Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
320 views

DC Motor Model Using Simscape

dc motor model using simscape matlab

Uploaded by

guddu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
320 views

DC Motor Model Using Simscape

dc motor model using simscape matlab

Uploaded by

guddu
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 27

DC Motor Model

Using Simscape

Engr. Salim Lashari


Introduction to Simscape
• Simscape™ provides an environment for modeling and
simulating physical systems spanning mechanical, electrical,
hydraulic, and other physical domains. It provides
fundamental building blocks from these domains that you
can assemble into models of physical components, such as
electric motors, inverting op-amps, hydraulic
valves. Because Simscape components use physical
connections, your models match the structure of the
system you are developing.
• Simscape models can be used to develop control systems
and test system-level performance.
• You can parameterize your models using MATLAB variables
and expressions, and design control systems for your
physical system in Simulink®.
Overview of DC Motor Example

• In this example, you model a DC motor driven


by a constant input signal that approximates a
pulse-width modulated signal and look at the
current and rotational motion at the motor
output.
Selecting Blocks to Represent System
Components
• Select the blocks to represent the input signal,
the DC motor, and the motor output displays.
• The following table describes the role of the
blocks that represent the system components.
Block Description
Solver Configuration Defines solver settings that apply to all physical modeling
blocks.

DC Voltage Source Generates a DC signal.

Controlled PWM Voltage Generates the signal that approximates a pulse-width


modulated motor input signal.

H-Bridge Drives the DC motor.

Current Sensor Converts the electrical current that drives the motor into a
physical signal proportional to the current.

Ideal Rotational Motion Sensor Converts the rotational motion of the motor into a physical
signal proportional to the motion.
Block Description

DC Motor Converts input electrical signal into mechanical motion.

PS-Simulink Converter Converts the input physical signal to a Simulink® signal.

Scope Displays motor current and rotational motion.

Electrical Reference Provides the electrical ground.

Mechanical Rotational Provides the mechanical ground.


Reference
Building the Model

• Create a Simulink model, add blocks to the


model, and connect the blocks.
• Create a new model.
• Add to the model the blocks listed in the
following table. The Library column of the
table specifies the hierarchical path to each
block.
Block Library Path Quantity
Solver Configuration Simscape > Utilities 1
DC Voltage Source Simscape > Foundation Library > Electrical > Electrical Sources 1

Controlled PWM Simscape > SimElectronics > Actuators & Drivers > Drivers 1
Voltage
H-Bridge Simscape > SimElectronics > Actuators & Drivers > Drivers 1

Current Sensor Simscape > Foundation Library > Electrical > Electrical Sensors 1

Ideal Rotational Simscape > Foundation Library > Mechanical > Mechanical 1
Motion Sensor Sensors
DC Motor Simscape > SimElectronics > Actuators & Drivers > Rotational 1
Actuators
PS-Simulink Converter Simscape > Utilities 2
Scope Simulink > Commonly Used Blocks 2

Electrical Reference Simscape > Foundation Library > Electrical > Electrical 1
Elements
Mechanical Rotational Simscape > Foundation Library > Mechanical > Rotational 1
Reference Elements
Building the Model

• Connect the blocks as shown in the following


figure.
Specifying Model Parameters

Specify the following parameters to represent


the behavior of the system components:
• Motor Input Signal Parameters
• Motor Parameters
• Current Display Parameters
• Torque Display Parameters
Motor Input Signal Parameters
1. Set the DC Voltage Source block parameters as follows:
Constant voltage = 2.5
Motor Input Signal Parameters
• Set the Controlled PWM Voltage block
parameters as follows:
• PWM frequency = 4000
• Simulation mode = Averaged
• This value tells the block to generate an output
signal whose value is the average value of the
PWM signal. Simulating the motor with an
averaged signal estimates the motor behavior in
the presence of a PWM signal. To validate this
approximation, use value of PWM for this
parameter.
Motor Input Signal Parameters

• Set the H-Bridge block parameters as follows:


• Simulation mode = Averaged
• This value tells the block to generate an
output signal whose value is the average value
of the PWM signal. Simulating the motor with
an averaged signal estimates the motor
behavior in the presence of a PWM signal. To
validate this approximation, use value
of PWM for this parameter.
Motor Parameters
• Configure the block that models the motor.
• Set the Motor block parameters as follows, leaving the unit
settings at their default values where applicable:
• Electrical Torque tab:
– Model parameterization = By rated power, rated speed &
no-load speed
– Armature inductance = 0.01
– No-load speed = 4000
– Rated speed (at rated load) = 2500
– Rated load (mechanical power) = 10
– Rated DC supply voltage = 12
• Mechanical tab:
– Rotor inertia = 2000
– Rotor damping = 1e-06
Current Display Parameters

• Specify the parameters of the blocks that create


the motor current display:
• Current Sensor block
• PS-Simulink Converter1 block
• Scope1 block
• Of the three blocks, only the PS-Simulink
Converter1 block has parameters. Set the PS-
Simulink Converter1 block Output signal unit
parameter to A to indicate that the block input
signal has units of amperes.
Torque Display Parameters

• Specify the parameters of the blocks that create the


motor torque display:
• Ideal Rotational Motion Sensor block
• PS-Simulink Converter block
• Scope block
• Of the three blocks, only the PS-Simulink Converter
block has parameters you need to configure for this
example. Set the PS-Simulink Converter block Output
signal unit parameter to rpm to indicate that the block
input signal has units of revolutions per minute.
• Note: You must type this parameter value. It is not
available in the drop-down list.
Configuring the Solver Parameters

• Configure the solver parameters to use a


continuous-time solver because SimElectronics
models only run with a continuous-time solver.
Increase the maximum step size the solver can
take so the simulation runs faster.
1. In the model window, select Simulation > Model
Configuration Parameters to open the
Configuration Parameters dialog box.
2. Select ode15s (Stiff/NDF) from the Solver list.
3. Enter 1 for the Max step size parameter value.
4. Click OK.
Running the Simulation and Analyzing
the Results
• In this part of the example, you run the
simulation and plot the results.
• In the model window,
select Simulation > Run to run the simulation.
• To view the motor current and torque in the
Scope windows, double-click the Scope blocks.
You can do this before or after you run the
simulation.
• The following plot shows the motor current.
Motor Current
Motor RPM
Conclusion

As expected, the motor runs at about 2000 rpm


when the applied DC voltage is 2.5 V.

You might also like