Estimation of Wing Loading and Thrust Loading

ESTIMATION OF
WING LOADING
AND THRUST
LOADING
INTRODUCTORY REMARKS ON
APPROACH OF REF.1.6 FOR
CHOOSING WING LOADING (W/S)
AND THRUST LOADING (T/W) OR
POWER LOADING (W/ P)
 It is felt that the approach of Ref.1.6, though presented about 50 years ago,
is still relevant. It was presented by Prof. A.A. Lebedinski of Moscow
Aviation Institute, in his lectures on ‘Airplane design‘ at Indian Institute of
Science Bangalore, India during 1963-64. The salient features of this
approach are as follows.
 (i) Derive simplified relations between the chosen performance parameter
and the wing loading.
 (ii) Obtain the wing loading which satisfies/optimizes the chosen parameter
e.g. landing distance, thrust required for Vp, fuel required for range.
 (iii) Examine the influence of allowing small variations in wing loading from
the optimum value and obtain a band of wing loadings. This would give an
estimate of the compromise involved when (W/S) is non-optimum.
 (iv) After all important cases are examined, choose the final wing loading
as the best compromise.
 (v) With the chosen wing loading, obtain (T/W) or (W/P) which satisfy
requirements of Vmax, (R/C)max, ceiling (Hmax), take-off field length
( Sto ) and maximum turn rate (ψ). If the requirements of engine output in
these cases are widely different, then examine possible compromise in
specification. After deciding the (T/W) or (W/P) obtain the engine output
required.
 Choose the number of engine(s) and arrive at the rating per engine. Finally
choose an engine from the engines available from different engine
manufacturers.
SELECTION OF WING
LOADING BASED ON
LANDING DISTANCE
 Landing distance (Sland) is the horizontal distance the airplane covers from
being at the screen height till it comes to a stop.
 The flight speed at this point is called ‘Approach speed’ and denoted by VA.
The glide angle during approach is generally 3o.
 Then, the airplane performs a flare to make the flight path horizontal and
touches the landing field at touch down speed (VTD).
 Subsequently, the airplane rolls for a duration of about 3 seconds and then
the brakes are applied.
 The horizontal distance covered from the start of the approach till the
airplane comes to a halt is the landing field length.
 VA = 1.3(Vs)land, VTD = 1.15(Vs) land
RELATION BETWEEN SLAND
AND WING LOADING
 To illustrate the steps, Eq.
(4.2a) which is applicable for
airplanes governed by FAR
25, is considered.
GUIDELINES FOR VALUES OF
CLMAX OF WINGS WITH
VARIOUS HIGH LIFT DEVICES
 The value of CLmax depends on the following.
 a) The geometry of the wing i.e. aspect ratio (A), taper ratio (λ) and sweep (Λ).
 b) Airfoil shape.
 c) Flap type, ratio of flap area to wing area (Sflap /S) and flap deflection (δflap).
 d) Type of leading edge slat and its deflection.
 e) Reynolds number.
 f) Surface texture.
 g) Interference effects due to fuselage, nacelle and pylons.
 h) Influence of propeller slip stream, if present.

 Commonly used flaps, slot and slat are shown in Fig.4.1.
 At this stage of preliminary design, the data collection, and the three view
drawing presented in chapter 2, give some information about the type of
high lift devices likely be used on the wing and the amount of wing sweep.
PERMISSIBLE VARIATION IN PLAND BY
ALLOWING REASONABLE VARIATION IN
SLAND
 The choice of wing loading will also be affected by other requirements like
Vmax and (R/C)max.
 Since design is a compromise between possibly conflicting requirements,
the change in pland when sland is varied within ± Δsland needs to be
examined.
 Figure 4.3 also shows the limits within which pland can be varied with
landing distance within sland ± Δ sland.
 The wing loading (W/S) of the airplane is always specified with reference to
the take-off weight (WTO or Wo). Hence, the wing loading from landing
consideration, based on take-off weight, is
 The weight of the airplane at the time of landing (Wland) is generally lower
than WTO.
 The difference between the two weights is due to the consumption of fuel
and dropping of any disposable weight.
 However, to calculate Wland only a part of the fuel weight is subtracted,
from the take off weight.
 The relationship between Wland and WTO is expressed as:
DIFFERENT TYPES OF WING AREAS –
PLANFORM AREA, EXPOSED WING
AREA, REFERENCE AREA AND WETTED
AREA.
 At this juncture, the definitions of different types of wing areas are
presented below.
 Planform is the geometric shape of the wing in the plan view.
 The area of this shape is the planform area.
 Exposed wing area is the planform area of the wing outside the fuselage
 Reference wing: For subsonic airplanes the reference wing is a trapezoidal
wing.
 This shape is obtained by extending the leading and trailing edges of the
exposed wing upto the fuselage centre line.
 The planform area of this wing is the reference area of the wing.
 It may be noted the fillet near the wing fuselage junction and the rounding
off near the wing tip are not considered.
 Equivalent trapezoidal wing: It is a trapezoidal wing whose root chord is at
the fuselage centre line and has the area same as the planform area.
SELECTION OF WING
LOADING BASED ON
PRESCRIBED FLIGHT SPEED
(VP)
 It may be added that for a passenger airplane, the power required for take-
off and climb are generally higher than that required during cruise.
 With an engine rating satisfying these requirements, a maximum speed
(Vmax) of 1.05 to 1.2 times the cruising speed is attainable at Hcr.
 The optimization from the consideration of Vp, aims at finding out the wing
loading which will result in the lowest thrust requirement (Tvp) for a chosen
Vp at Hp.
 The steps are as follows.
SELECTION OF WING
LOADING BASED ON
ABSOLUTE CEILING (HMAX)

Estimation of Wing Loading and Thrust Loading

Uploaded by

Copyright:

Available Formats

Estimation of Wing Loading and Thrust Loading

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Estimation of Wing Loading and Thrust Loading

Uploaded by

Copyright:

Available Formats

What are the steps involved in selecting wing loading based on landing distance?

What factors affect the maximum lift coefficient of a wing?

ESTIMATION OF

 d) Type of leading edge slat and its deflection.

 g) Interference effects due to fuselage, nacelle and pylons.

 h) Influence of propeller slip stream, if present.

You might also like