Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Ce260 CH 5

Download as ppt, pdf, or txt
Download as ppt, pdf, or txt
You are on page 1of 34

CE 260

SURVEYING
CHAPTER 5
THEODOLITES

• General Background:
• Theodolites or Transits are surveying
instruments designed to precisely
measure horizontal and vertical angles.
THEODOLITES
• They are used to
establish straight and
curved lines.
• To establish or
measure distance
(Stadia)
• To establish Elevation
when used as a level.
(When we set the
vertical angle to 90°).
TRANSITS
They have:
• 4 screw level base.
• Metallic vertical and
horizontal circles read
with Vernier scale.
• Plumb Bob
• Low precision
• Old instrument. Not in
use now.
THEODOLITES
They have:
• 3 screw level base
• Glass horizontal and vertical circles, read
directly or through micrometer.
• Right angle prism (optical plummet)
• High precision
ELECTRONIC THEODOLITE
– Electronic read out 1” eliminate mistakes and
reading the angles.
– Precision varies from 0.5” – 20”
– Zero is set by a button.
– Repeated angle averaging.
– Replacing optical theodolites (It is less
expensive to purchase and maintain).
THEODOLITES
Top image shows the
Electronic Theodolite.
Bottom shows the
Scale readings.
THEODOLITES
• ELECTRONIC
THEODOLITE
DETAILS
THEODOLITES
• OPERATION KEYS
AND DISPLAYS
THEODOLITES
• Field noted for
repeated angles
THEODOLITES SET-UP
1. Place the instrument over the point with
the tripod plate as level as possible and
with two tripod legs on the downhill side,
if applicable.
2. Stand back a pace or two and see if the
instrument appears to be over the
station; if it does not, adjust the location
and check again from a pace or two
away.
THEODOLITES SET-UP
3. Move to a position 90° opposed to the
original inspection location and repeat
step 2.
4. Check that the station point can now be
seen through the optical plummet (or that
the laser plummet spot is reasonably
close to the setup mark). Then push the
tripod legs firmly by pressing down on
the tripod shoe spurs.
THEODOLITES SET-UP
5. While looking through the optical plumb
(or at the laser spot), manipulate the
leveling screws (one, two or all the three at
a time) until the cross hair (bull’s-eye) of
the optical plummet or the laser spot is
directly on the station mark.
6. Level the theodolite circular bubble by
adjusting the tripod legs up or down.
THEODOLITES SET-UP
7. Perform a check through the optical
plummet or note the location of the laser
spot to confirm that it is still quite being
over the station mark.
8. Turn one (or more) leveling screws to be
sure that the circular bubble is now exactly
centered (if necessary).
THEODOLITES SET-UP
9. Loosen the tripod clamp bolt a bit and
slide the instrument on the flat tripod top (if
necessary) until the optical plummet or
laser spot is exactly centered on the
station mark. Retighten the tripod clamp
bolt and reset the circular bubble, if
necessary.
THEODOLITES SET-UP
10. The instrument can now be precisely
leveled by centering the tubular bubble.
Set the tubular bubble so that it is aligned
in the same direction as two of the foot
screws. Turn these two screws (together
or independently) until the bubble is
centered. Then turn the instrument 90°, at
which point the tubular bubble will be
aligned with the third leveling screw.
THEODOLITES SET-UP
10. Next, turn that third screw to center the
bubble. The instrument now should be
level, although it is always checked by
turning the instrument through 180°.
THEODOLITES
Repeating optical theodolite:
• Has 3 leveling screws
• Optical plummet, light weight, glass circle,
micrometer (to read the angles).
• Most theodolites are equipped with
compensating device (automatic
horizontal).
• 90° or 270° vertical angle of horizon.
THEODOLITES
• Micrometer used to read vertical and
horizontal angles.
• 2 independent motion (upper and lower). If
you move the upper motion, then the
angle does not change. But if you move
the lower motion, the angle will change.
THEODOLITES
Angle Measurement with an Optical
Theodolite
DIRECT OPTICAL THEODOLITE
• Has only one motion
(upper).
To find angle:
• Read the initial
direction (L target)
• Read the final
direction (R target)
• Determine the
difference between
the two.
DIRECT OPTICAL THEODOLITE
• Direct optical theodolite generally is more
precise. Some models can read directly
0.2” and estimate 0.1”.
• Several sightings are required for precise
work.
• Distribute initial reading around the circle
to minimize the effect of circle graduation
distribution, so initial reading read 0,
45,90,135,…
DIRECT OPTICAL THEODOLITE
• Angles
measured
with a
Direction
Theodolite
LAYING OFF ANGLES
• The angle is to be laid out no more precisely
than the least count of the transit or theodolite.
LAYING OFF ANGLES
• Process: Lock angle, rotate theodolite, then
open lock and measure again same angle.
Should have double the first angle
measurement.
PROLONGING A STRAIGHT LINE
• Start by taking
distance at A. Then
go to B, rotate 180°,
look back at A, plunge
and make another
line towards C.
BUCKING IN (INTERLINGING)
• Read A, then plunge to B. If Distance between B
and B’ is 1 M, then you have to move 0.5 M to
find C. then do the sighting again.
INTERSECTION OF 2 STRAIGHT
LINES
• Put 2 strings between
points and then get
the intersection.
PROLONGING A MEASUREMENT
LINE BY TRIANGULATION OVER
AN OBSTACLE
PROLONGING A LINE PAST AN
OBSTACLE
There are 3 methods for it:
1. Right-angle offset method.
2. Random-line method.
3. Triangulation method.
PROLONGING A LINE PAST AN
OBSTACLE
THE END OF CHAPTER 5

• THANK YOU!

You might also like