Cellphone Based Device Control

CELLPHONE BASED DEVICE
CONTROL WITH VOICE

ACKNOWLEDGEMENT
BY:-
ANURAG SRIVASTAV
GUIDED BY:-
ANKUR MISHRA
MS.RAJNI PARASHAR
ANKITA JAIRATH
DHARMENDRA KUMAR
E.C.E.4thYEAR
OBJECTIVE
In this project operating of home appliances like lights
and water pump take place from office or any remote
places.
If we forgot to switch off the lights or other appliances
while going out,it helps you to turn off the appliance
with your cellphone
Our cellphone works as the remote control for our
home appliances.
APPARATUS USED
SEMICONDUCTORS-
Microcontroller(AT89C51)
Voice recording and playback device(APR9600)
DTMF receiver(MT8870)
Relay driver(ULN2003)
Regulator(6V)
CONTD….
Resistors
Diode
LED
Capacitors
Electronic mic
Mobile phone headset connector etc….
Features
New
Voice
acknowledgement
Automation of home
appliance system
Remote sensing
BLOCK DIAGRAM
Microcontroller(AT89C51)
The AT89C51 is a low-power, high-performance CMOS 8-bit
microcomputer with 4Kbytes of Flash programmable and erasable
read only memory (PEROM).
The deviceis manufactured using Atmel’s high-density nonvolatile
memory technology and is compatible with the industry-standard
MCS-51 instruction set and pinout.
The on-chip Flash allows the program memory to be reprogrammed
in-system or by a conventional nonvolatile memory programmer.
 By combining a versatile 8-bit CPU with Flash on a monolithic chip,
the Atmel AT89C51 is a powerful microcomputer which provides a
highly-flexible and cost-effective solution to many embedded control
applications
Microcontroller(pin diagram)
Features
4K Bytes of In-System Reprogrammable Flash Memory
Endurance: 1,000 Write/Erase Cycles
Fully Static Operation: 0 Hz to 24 MHz
Three-level Program Memory Lock
128 x 8-bit Internal RAM
32 Programmable I/O Lines
Two 16-bit Timer/Counters
Six Interrupt Sources
Programmable Serial Channel
Low-power Idle and Power-down Modes
Voice recording and playback device(APR9600)
The APR9600 device offers true single-chip voice
recording,non-volatile storage, and playback capability for 40 to
60 seconds.
The device supports both random and sequential access of
multiple messages.
Sample rates are user-selectable, allowing designers to customize
their design for unique quality and storage time needs.
Integrated output amplifier, microphone amplifier, and AGC
circuits greatly simplify system design.
 The device is ideal for use in portable voice recorders, toys, and
many other consumer and industrial applications.
APR9600 IC
DTMF receiver(MT8870)
The MT-8870 is a DTMF Receiver that integrates both
band split filter and decoder functions into a single 18-pin
DIP or SOIC package.
 It is manufactured using CMOS process technology.
The MT-8870 offers low power consumption (35 mW
max) and precise data handling.
MT8870
Relay driver(ULN2003)
The ULN2003 is a monolithic high voltage and high current
Darlington transistor arrays.
It consists of seven NPN Darlington pairs that features high-
voltage outputs with common-cathode clamp diode for switching
inductive loads.
The collector-current rating of a single Darlington pair is 500mA.
The Darlington pairs may be paralleled for higher current
capability.
Applications include relay drivers, hammer drivers, lamp drivers,
display drivers(LED gas discharge),line drivers, and logic buffers.
ULN2003
Regulator(6V)
Here is the elementary 6V 1A power supply
circuit using 7806 IC.
The 7806 three-terminal positive voltage
regulator is available in the TO-220/D-PAK
package making them useful in a wide range of
applications.
7806 employs internal current limiting,
thermal shut down and safe operating area
protection, making it essentially indestructible.
 If proper heat sinking is provided, it can
deliver over 1 ampere output current.
Regulator(6V) Circuit
Single pole double throw (SPDT)
switch(SA630)
The SA630 is a wideband RF switch fabricated in
BiCMOS technology and incorporating on-chip
CMOS/TTL compatible drivers.
Its primary function is to switch signals in the frequency
range DC -1GHz from one 50W channel to another.
The switch is activated by a CMOS/TTL compatible
signal applied to the enable channel 1 pin (ENCH1).
The extremely low current consumption makes the
SA630 ideal for portable applications.
The excellent isolation and low loss makes this a
suitable replacement for PIN diodes.
Cell phone headset connector
Something Name Direction Description

Pin
1 Mic Microphone
2 Spk Speaker
3 Gnd Ground
Dual in-line package (DIP)
Dual in-line package (DIP) switches are electronic packages that
consist of a series of tiny switches.
 DIP switches are used to configure computers and peripherals such as
circuit boards and modems.
Actuator choices for DIP switches include slide actuators, rocker
actuators, and side actuated levers (piano).
 A slide actuator configuration can have raised or recessed slides.
 A rocker actuator configuration can have raised or recessed rockers.
 A side actuated lever configuration is typically called piano style, the
"keys" are pressed down to actuate.
The number of positions available is equivalent to the number of
actuators on the DIP switch
THANK
YOU

Cellphone Based Device Control

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cellphone Based Device Control

Uploaded by

Copyright:

Available Formats

CELLPHONE BASED DEVICE

CONTROL WITH VOICE

Something Name Direction Description

You might also like