Advanced CN Lecture 1

Advanced Computer
Networks
Lecture 1
2.1 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
LAYERED TASKS
We use the concept of layers in our daily life. As an

example, let us consider two friends who communicate
through postal mail. The process of sending a letter to a
friend would be complex if there were no services
available from the post office.
2.2
Tasks involved in sending a letter
2.3
THE OSI MODEL
Established in 1947, the International Standards

Organization (ISO) is a multinational body dedicated to
worldwide agreement on international standards. An ISO
standard that covers all aspects of network
communications is the Open Systems Interconnection
(OSI) model. It was first introduced in the late 1970s.
2.4
Seven layers of the OSI model
2.5
The interaction between layers in the OSI model
2.6
An exchange using the OSI model
2.7
LAYERS IN THE OSI MODEL
In this section we briefly describe the functions of each

layer in the OSI model.
Physical Layer
Data Link Layer
Network Layer
Transport Layer
Session Layer
Presentation Layer
Application Layer
2.8
Physical layer
The physical layer is responsible for movements of

individual bits from one hop (node) to the next.
Representation of bits into signal levels

Bits Transmission rate
Line configuration
Physical topology
Transmission mode
1-9
Data Link layer
The data link layer is responsible for moving

frames from one hop (node) to the next.
Framing, Physical address, Flow control, Error Control, Access control1-

10
Network Layer
The network layer is responsible for the delivery of individual packets from
the source host to the destination host.
Logical addressing, Routing 1-

11
Transport layer
The transport layer is responsible for the delivery
of a message from one process to another.
Process addr, Segmentation/assembly, ordering,

1-
Connection control, Flow control, Error control
12
Session layer
2.13
Note
The session layer is responsible for dialog

control and synchronization.
2.14
Presentation layer
2.15
Note
The presentation layer is responsible for translation,

compression, and encryption.
2.16
Application layer
2.17
Note
The application layer is responsible for

providing services to the user.
2.18
Summary of layers
2.19
TCP/IP PROTOCOL SUITE
The layers in the TCP/IP protocol suite do not exactly

match those in the OSI model. The original TCP/IP
protocol suite was defined as having four layers: host-to-
network, internet, transport, and application. However,
when TCP/IP is compared to OSI, we can say that the
TCP/IP protocol suite is made of five layers: physical,
data link, network, transport, and application.
Topics discussed in this section:

Physical and Data Link Layers
Network Layer
Transport Layer
Application Layer
2.20
TCP/IP and OSI model
2.21
2.22
ADDRESSING
Four levels of addresses are used in an internet employing

the TCP/IP protocols: physical, logical, port, and specific.
Topics discussed in this section:

Physical Addresses
Logical Addresses
Port Addresses
Specific Addresses
2.23
Addresses in TCP/IP
2.24
Relationship of layers and addresses in TCP/IP
2.25
Example 2.1
In Figure 2.19 a node with physical address 10 sends a

frame to a node with physical address 87. The two nodes
are connected by a link (bus topology LAN). As the
figure shows, the computer with physical address 10 is
the sender, and the computer with physical address 87 is
the receiver.
2.26
Figure 2.19 Physical addresses
2.27
Example 2.2
most local-area networks use a 48-bit (6-byte) physical

address written as 12 hexadecimal digits; every byte (2
hexadecimal digits) is separated by a colon, as shown
below:
07:01:02:01:2C:4B
A 6-byte (12 hexadecimal digits) physical address.
2.28
Example 2.3
Figure 2.20 shows a part of an internet with two routers

connecting three LANs. Each device (computer or
router) has a pair of addresses (logical and physical) for
each connection. In this case, each computer is
connected to only one link and therefore has only one
pair of addresses. Each router, however, is connected to
three networks (only two are shown in the figure). So
each router has three pairs of addresses, one for each
connection.
2.29
Figure 2.20 IP addresses
2.30
Example 2.4
Figure 2.21 shows two computers communicating via the

Internet. The sending computer is running three
processes at this time with port addresses a, b, and c. The
receiving computer is running two processes at this time
with port addresses j and k. Process a in the sending
computer needs to communicate with process j in the
receiving computer. Note that although physical
addresses change from hop to hop, logical and port
addresses remain the same from the source to
destination.
2.31
Figure 2.21 Port addresses
2.32
Note
The physical addresses will change from hop to hop,

but the logical addresses usually remain the same.
2.33
Example 2.5
A port address is a 16-bit address represented by one

decimal number as shown.
753
A 16-bit port address represented

as one single number.
2.34

Advanced CN Lecture 1

Uploaded by

Copyright:

Available Formats

Advanced CN Lecture 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Advanced CN Lecture 1

Uploaded by

Copyright:

Available Formats

Advanced Computer

We use the concept of layers in our daily life. As an

Established in 1947, the International Standards

In this section we briefly describe the functions of each

The physical layer is responsible for movements of

Representation of bits into signal levels

The data link layer is responsible for moving

Framing, Physical address, Flow control, Error Control, Access control1-

Logical addressing, Routing 1-

Process addr, Segmentation/assembly, ordering,

The session layer is responsible for dialog

The presentation layer is responsible for translation,

The application layer is responsible for

The layers in the TCP/IP protocol suite do not exactly

Topics discussed in this section:

Four levels of addresses are used in an internet employing

Topics discussed in this section:

In Figure 2.19 a node with physical address 10 sends a

most local-area networks use a 48-bit (6-byte) physical

A 6-byte (12 hexadecimal digits) physical address.

Figure 2.20 shows a part of an internet with two routers

Figure 2.21 shows two computers communicating via the

The physical addresses will change from hop to hop,

A port address is a 16-bit address represented by one

A 16-bit port address represented

You might also like