Technical Features FT1800

Technical Features FT1800
Why need Blood and Infusion Warmer?
Hypothermia
 Anesthesia 1st hour : decrease core temp. 1 – 1.6ºC
 Intra- and post- surgery: if patient core temp. < 35ºc,

need 5h to back to normal
 Massive fluid infusion
 Elderly, weak, infant and children patients

Why need Blood and Infusion Warmer
Complications
 Shivering
 Decreased tissue oxygen
delivery,
 Cardiac arrhythmias
 Impair coagulation, so
increase blood loss

 Wound infection
 Prolong postoperative
recovery
 Impairs immune function
disorder
Why need Blood and Infusion Warmer?
 Enzymes moderate &

metabolize ⇨ temp.
sensitive
 Warmed Infusion
effectively
increase /maintain
core temp.
 Less thermal stress ⇨
infusion comfort
Advanced features
o Advanced control: microprocessor + temperature sensors
o User friendly interface: smart design, easy to operate
o High safety system:

 24h continuous operating & self-testing
 over-heating automatic cut off
 Visual & audio alarms
o Open system:
 Accept the standard IV tube hospitals using now
 No extra disposable costs
 The most economical solution, especially welcomed by developing countries

The most advanced tube heating
system in this sector worldwide
FT1800
FT1800
 1.4m warming profile
active & gentle warming
up to the patient
 Using standard IV tubing
 2min reach to 36ºC

*room temp. 20ºC
 warming capacity:
 1.5 L/H – one channel
The most effective heating

Single channels
system using standard tubing
Open system, heating up to the patient
IV tube is completely wrapped in,

Soft warming profile fits
no heat loss wide range of tubing size
FT1800
 Set temperature freely

33 - 41°C
 Alarming & automatic

cut-off protections
 Easy to operate
Big LED screen

User friendly interface
FT1800
General illustration
Infusion
Stand
Infusion
Tubing
Main Control
Body
Warming
Profile
LED
Control Screen
Panel
Power
Connection
Cable
Cable
Illustration of the holder and the warming profile
Illustration of the control panel
Key to set Key to set

temp. up temp. down
Key to switch between

Celsius and Fahrenheit
Key
Standby/Oper
ating
Illustration of LED screen
- the symbol of the alarm will appear on the screen only when the alarm is triggered
Installation & Operation
Step 1:
- Use the clamp to fix
the device firmly to the
infusion stand at the
position of 20-30cm
below the
infusion/blood bag
- Screw the fastening
screw
- The device is almost
equal to the drip bucket
Fastening
Screw Infusion Clamp
Stand
Step 2:
roll clamp
- Glide the roll clamp
next to the drip bucket
- Empty the air in
tubing to make
infusion channel ready
Step 3:
- Take the primed

infusion line at 2-3cm to
the end of patient side
to insert in the tail
(small end) of the
warming profile
2-3CM
Step 4:
- Move your thumb over

the infusion line and
press the line gently into
the groove towards the
head(big end) of the
warming profile, until the
Big end
infusion line is
completely wrapped in
the warming profile
Step 5:
- Place the ends of the

warming profile into the
holder to prevent the
infusion tube
contacting with the Big
ground Small End
End
Note ：
If the Infusion tubing is too
short to fill the warming
profile from the beginning to
the end, it is necessary to
ensure that the patient end
(where the fluid flows out) of
the warming profile is filled.
The head of the warming
profile can be left unfilled. Of
course, a long enough tubing
ensures the heating effect.
Step 6:
- Press the key or to
select the desired
temperature
- Adjust the appropriate
infusion rate and press the
key to start
Note: Resetting of
temperature can only be
performed in Standly mode.
Note ：
If the infusion needs to be stopped for more
than 3 minutes, press the key to stop
warming (Standby). By press the key again
to resume it.
Shutting down the device
 press the key to enter Standby mode.
 Release all pressure in the infusion system by
switching off the pressure cuffs or infusion

pumps.
 Remove the consumable material from the
warming profile and dispose it according to the

relevantregulations.
 Disconnect the device from the power supply.
Clean and disinfect the equipment according to

instructions.
Maintenance
 After each use, if possible, please clean device
surface, fastening clamp and warming profile. Use
disinfectant to clean them periodically.
 Wring soft cloth with water or soap lye and use it to
clean device.
 Don’t allow cleaning fluids and disinfectant enter
ventilator of device.
 Disinfectants should be based on alcohol liquid
without oxygen releasing (with sodium hypochlorite and
1.4% bleach solution or < 0.2% acetaldehyde).
 It can’t be immersed in liquid and can’t be disinfected
in autoclave or by heat chemistry method.
Used in clinical settings
（ major dept. ）
Anesthesia, OT ：
Blood transfusion & infusion during operation
ICU,SICU,CCU,NICU:
Blood ， infusion ， enteral/parenteral nutrition ，
blood return feeds
Emergency care, ambulance ：

Blood transfusion & infusion
（ major dept. ）
Blood bank ：
Whole blood from cold storage
Dialysis:
Blood return feeds
Peritoneal dialysis
（ major dept. ）
Urinary surgery:
Rinse solution for prostate or bladder
Oncology
Intraperitoneal perfusion chemotherapy
（ major dept. ）
Obstetrics and Gynecology ：

Maternal
Neonates, paediatrics:
Blood transfusion & infusion
Tenderness
&
Excellence
Keep every life
well…….

Technical Features FT1800

Uploaded by

Copyright:

Available Formats

Technical Features FT1800

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Technical Features FT1800

Uploaded by

Copyright:

Available Formats

Technical Features FT1800

Why need Blood and Infusion Warmer?

 Anesthesia 1st hour : decrease core temp. 1 – 1.6ºC

 Intra- and post- surgery: if patient core temp. < 35ºc,

 Massive fluid infusion

 Elderly, weak, infant and children patients

increase blood loss

 Enzymes moderate &

o Advanced control: microprocessor + temperature sensors

o User friendly interface: smart design, easy to operate

o High safety system:

 over-heating automatic cut off

 Visual & audio alarms

 No extra disposable costs

 The most economical solution, especially welcomed by developing countries

 Using standard IV tubing

 2min reach to 36ºC

The most effective heating

IV tube is completely wrapped in,

 Set temperature freely

 Alarming & automatic

Big LED screen

Key to set Key to set

Key to switch between

- Take the primed

- Move your thumb over

- Place the ends of the

switching off the pressure cuffs or infusion

warming profile and dispose it according to the

Clean and disinfect the equipment according to

Emergency care, ambulance ：

Obstetrics and Gynecology ：

You might also like