Latex Thread

LATEX THREAD
BY
K. ARIVARASAN
(2017508003)
P.S.ARTHI (2017508004)
PREPARATION
• Latex thread is prepared by EXTRUSION PROCESS.

• Latex threads are produced by Continuous extrusion of compounded latex in
to a wet coacervant bath (e.g. 20 – 40 % acetic acid). This is followed by
washing with hot water, drying at 60 – 80°C in hot air and vulcanizing at 120
– 130°C in hot air. The vulcanized thread is passed through a bed of talc and
wound on to bobbins or drums and post cured at 60°C in hot air for 24 hr.
PROCESS STEPS
• Latex compounding
• Coacervant bath
• Latex thread extrusion
LATEX COMPOUNDING
Latex should be free from non-rubber constituents. The compounding
formulation should have minimum number of additives in solid form.
Dispersions of compounding ingredients should be very finely ground during
ball milling. Dispersions should be free from air bubbles / frothing. Air
entrapment should be nil or minimum during various compounding and
processing operations. Before extrusion, the compound should be passed
through a very fine mesh and then allowed to deaerate by application of partial
vacuum.
COACERVANT BATH
• Acetic acid diluted at 20 % - 40 % range is used as coacervant bath.

• When latex threads of relatively larger diameter are produced and when
shorter times of immersion in coacervants are used; the concentration of
acetic acid is higher.
• The outside surface of the thread coacervants first forming a thin-walled
rubber film on the surface while the interior latex compound in the thread is
still fluid.
• The interior latex compound coacervants by the action of acetic acid diffused
through the already set layer.
• Saline solutions are sometimes preferred for thicker diameter threads as they effect
rapid setting of the entire thickness.
• When a blend of acetic acid and saline solution is used; the external skin
formation on the latex thread is immediate.
• This skin acts as semi-permeable membrane and osmosis occurs through this film
as a result of which larger quantity of water is lost from the thread, which helps its
solidification.
• The strength of the coacervant batch is maintained within narrow limits
throughout the proces since the same varies considerably due to consumption of
acetic acid.
LATEX THREAD EXTRUSION
• The extrusion nozzles are made from boro silicate glass capillary with accurate
dimensional control these are then fused into a wider glass delivery tubes.
• Several sets of nozzles of different bore sizes are used as per the finished
product, diameter requirements.
• By varying extrusion conditions, it is possible to use a single nozzle to produce
extrudates in a range of diameters.
• The extrusion of latex thread takes place under the coacervant batch.
SUBSEQUENT PROCESS OPERATIONS
• After the coacervant batch the threads are passed through a hot water bath where water-soluble impurities are
leached out. The thread is strong at this stage and is subjected to a ‘stretching’ process to control the final diameter.
• The thread then carried to a hot air chamber for drying and vulcanization. The hot air chamber has a drying zone
maintained at approx. 70°C and the vulcanization zone is at about 125 – 130°C. Between the two zones one more
zone is maintained at intermediate temperatures between 70°C and 120°C. The total time in the Vulcanizer depends
on the diameter of the thread (typically between 5 to 7 minutes). The thread is thoroughly dried before it reaches the
vulcanization zone.
• The thread is then passed through a bed of talc and is inspected for defects on an inspection table as part of the
continuous process. The thread is finally wound on bobbins or drums under slight tension. The bobbins or drums are
finally post cured at 60°C in hot air ovens for 24 hr to complete the cure cycle.
• Various other quality control tests are then carried out. The compounds have to be designed to with stand
degradative forces such s solvent resistance, detergent resistance, superior aging properties, etc. by employing potent
non-staining type antioxidants.
TYPICAL COMPOUNDING FORMULATIONS
• GENERAL PURPOSE LATEX THREAD
INGREDIENTS PBW
60 % NHR Latex (LA) 167
10 % KO Solution 3
20 % Potassium Laurate 3
50 % Zinc oxide dispersion 6
50 % Titanium dioxide dispersion 10 – 15
50 % Antioxidant Dispersion 3
50 % Colloidal sulphur dispersion 3.5
50 % ZMBT Dispersion 2.0 – 3.0
50 % ZDBC Dispersion 0.5
• HEAT RESITANT LATEX THREAD
INGREDIENTS PBW
60 % NR Latex (LA-T2) 167
10 % KOH Solution 3
20 % Potassium Laurate 3
50 % Antioxidant Dispersion 4
50 % Zinc oxide Dispersion 8
50 % Titanium Dioxide Dispersion 10 – 15
50 % ZMBT Dispersion 3
50 % ZDBC Dispersion 1
50 % DPTT Dispersion 3.0 – 3.5
TESTING OF LATEX RUBBER THREAD
• Rubber threads are tested based on BIS 14424-1997 or as ASTMD-3845-1990.

• The important test parameters for thread are:
Count
Schwartz value
Tensile strength
Ageing resistance
COUNT
The count of a rubber thread is the number of

threads which when placed , side by side , measure
23.4 mm.
SCHWARTZ VALUE
Schwartz value of a rubber thread is the mean modulus on

extension and retraction during the sixth cycle of a sample thread
which has been extended to and retracted from an elongation 100%
greater than the elongation at which the modulus is measured.
TENSILE STRENGTH & AGING RESISTANCE
Tensile strength , elongation at break and aging resistance of rubber thread is
measured.
TECHNICAL REQUIRMENTS OF THE LATEX

PARAMETER GENERAL PURPOSE HEAT RESISTANT THREAD
THREAD.
Tensile Strength MPa, min. 24 24
Elongation at break % min. 750 750
Schwartz value , Mpa ,min. 2 2
Tensile strength retention after 65 75
ageing at 100 for 22 hours ,min.
Schwartz value % retained after 2 - 50
hours ageing at 150 degree Celsius
,min
APPLICATION
• HOSIERY APPLICATION
• Latex Rubber Thread finds major applications in the hosiery sector. Latex Rubber threads are primarily used to
manufacture elastic tapes mainly used in foundation garments like briefs, trunks, panties, brassieres etc and shorts,
pants, skirts, sportswear, sock tops etc. They are also used in elastic tapes for diapers, shoe uppers, headbands and
wristband for sportsmen and travel goods.
• SPECIAL APPLICATIONS
• Latex Rubber threads are also used to some of the niche' applications like toys, fishing baits, Pole fishing, bungee
cords etc. These are specially made color threads and needs extra care in the production. Colored Latex rubber
threads find application in making koosh balls, hairs for dolls etc
• The other niche segments where rubber threads are used are Medical nettings, meat packing, braids, laces, cords,
poly catheter manufacturing and webbing for furniture.
THANK YOU.

Latex Thread

Uploaded by

Copyright:

Available Formats

Latex Thread

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Latex Thread

Uploaded by

Copyright:

Available Formats

LATEX THREAD

• Latex thread is prepared by EXTRUSION PROCESS.

• Acetic acid diluted at 20 % - 40 % range is used as coacervant bath.

• Rubber threads are tested based on BIS 14424-1997 or as ASTMD-3845-1990.

The count of a rubber thread is the number of

Schwartz value of a rubber thread is the mean modulus on

TECHNICAL REQUIRMENTS OF THE LATEX

You might also like