Electric Motor Controls

MAGM 225
Electric Motor Controls
Mr. Conrado
Motor Control
Electric motors present some special problems from the standpoint of control. An electric motor will try to provide the power required by a load, even if it results in self-destruction. Therefore a motor must be protected from overloads. A motor draws up to six times as much current when the rotor is not turning as it does when operating at full speed. If a motor should stall the control device and the disconnect switch must be capable of handling the high locked-rotor current.
Types of Motor Controllers

A controller is simply a means of closing the circuit supplying power to an electrical motor. The most simple control device is a cord and plug. (1/8hp or less) A branch-circuit protective device, ie breaker, may serve as the controller for stationary motors of 1/8 HP or less that normally operate continuously A time delay circuit breaker is also allowed as a control device. A fusible knife switch may act as a motor controller provided it is rated for the horsepower rating of the motor supplied.
Magnetic Motor Starter

The main contacts are located inside the unit Repair kits are available When current is supplied to the internal solenoid the motor-starter contacts are closed. An overload relay section is added to the motor starter to sense motor current.
NEMA Sizes
NEMA has developed a standard numbering system for motor starter sizes. All manufactures use this system The larger the rating number the greater the horsepower rating of the starter. Are rated according to the current they will be expected to carry continuously, and interrupt the if the motor should stall. Motor starters come in 2 or 3 poles. 2 pole is for single phase and 3 pole for 3 phase. A 3 pole motor starter will handle a single phase motor with a horsepower rating half as large as 3 phase motor.
Enclosures
The motor-starter housing is selected for the environment in the area. NEMA has developed a standard numbering system for enclosures and require they be marked by the manufacture.
NEMA 1 - dry and free from dust and flammable materials NEMA 3 weather resistant suitable for outdoors but not dusty conditions. NEMA 4 water and dust tight. NEMA 4x water and dust tight but also corrosion resistant. NEMA 7 Explosion proof. NEMA 9 Dust Ignition proof
Motor-Full load current

The motor full-load current is used to determine the minimum size of circuit components. The name plate current rating must be used for selecting the maximum size motor running overload protection. Wires supplying a single motor shall have an amperage rating of not less that 1.25 times the full-load current of the motor.
Short-Circuit Protection
Motor circuits must be protected from excessive current, ground faults, and short circuits. Over current protection can be fused or circuit breaker a circuit beginning. Short circuit and ground fault must be capable of carrying the starting current of the motor. A single-phase, 5-hp, 230v motor with a nameplate of 28amps drives a normal load. Determine the overload device.
Full load current = 28A Fuse multiplier = 125% 1.25x28A=35A Use a 50-A fuse.
Service supplying several motors

The feeder wires are required to have a minimum rating equal to the sum of the full-load current of all motors supplied, plus 25%.
Motors of 5-hp 28a , 3-hp 17a, 1-hp 8a, and 2-hp 12amp.=72amps. No. 4 AWG minimum (from wire charts)
The disconnect must be selected for a horsepower rating of not less than the sum of all HP ratings.
5+3+1+2=11hp The disconnect closest is likely 15 hp If a breaker is used it must be a minimum of 115% of the sum of the full-load current for all motors served.
(28+17+8+12)1.15=75Amps
Feeder Taps
A common practice is to tap motor branch circuits from a motor feeder. This is permitted as long as the branch-circuit wire is terminated at an over current of proper size.
Motor Control Circuit

A magnetic motor starter is operated with an electric solenoid coil. Here we have a typical wiring diagram for a magnetic motor control. The thick lines are the power flow to the motor, the thin lines belong to the control circuit and generally are prewired by the manufacture.
Control Devices
Common wiring schematics use basic symbols and terminology. Switches and contacts are the basic control components, and they take several different forms. They can be operated mechanically, by timer, change in condition like temperature, pressure, flow, liquid level, or humidity. Switches and contacts are described by the number of pole and number of throws.
Poles the number of paths into a switch or contact. Throws the number of paths leaving each pole.
It must also be known if the switch is normally open or normally closed when inactivated.
Control Devices
The common types of switches and contacts are incorporated into various types of control devices.
Reversing Motor Starters

Electric motors may be called upon to drive a machine which must be reversible. A reversible motor starter is required to select the desired rotation direction. 3-phase only two of the three leads need to be reversed. Single phase the start windings must be reversed with respect to the run windings. Drum switch has forward, reverse, and stop. Note the phase rotation at the motor for forward and reverse.

Electric Motor Controls

Uploaded by

Copyright:

Available Formats

Electric Motor Controls

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electric Motor Controls

Uploaded by

Copyright:

Available Formats

MAGM 225

Electric Motor Controls

Types of Motor Controllers

Magnetic Motor Starter

Motor-Full load current

Service supplying several motors

Motor Control Circuit

Reversing Motor Starters

You might also like