The BM@N spectrometer at the NICA accelerator complex.

The BM@N experiment operates as part of the NICA complex (see Fig. 2). For light and heavy ions, the accelerator facility provides different ways of injection into the Nuclotron. Light ions (d-Mg) are accelerated up to an energy of 5 AMeV by a linear accelerator LU-20, after which the extracted beam is directly injected into the Nuclotron ring. The heavy ion linear accelerator Linac injects the beam first into the Booster ring. After acceleration up to $500\,{\rm AM}e{\rm V}$, the beam is injected into the Nuclotron for further acceleration up to 4.5 AGeV. Ion beams extracted from the Nuclotron can be delivered either to the BM@N fixed target experiment or to the NICA collider. At the collider, two experimental areas are reserved for two major experiments  $-$  the Multipurpose Detector (MPD) and the Spin Physics Detector (SPD) NICAWhitePaper .

The beam extracted from the Nuclotron is transported to the BM@N experimental area over a distance of about $150\,m$ by a set of dipole magnets and quadrupole lenses. This transport line is enclosed in a vacuum stainless steel pipe. The final steering of the beam on the BM@N target is performed by a pair of VKM and SP-57 dipole magnets, which allow a small beam bending in vertical and horizontal planes, correspondingly. They are placed respectively at a distance of approximately 5.7 and $7.7\,m$ from the target (Fig. 5). In addition, a doublet of quadrupole lenses is used for optimal focusing of the beam on the target. They are placed at about 10.0 and $12.5\,m$ upstream of the target, respectively.

The target is located at the pole edge of the SP-41 analyzing magnet close to its entrance. After the target, the beam ions are deflected by the SP-41 magnetic field ($\int Bdl=3.15\,\rm{Tm}$ at the maximum current of $2000\,A$) and the deflected beam passes through the entire setup also in the vacuum beam pipe. The position of the vacuum beam pipe after the target is fixed. For experiments at different beam energies, the magnetic field of the analyzing magnet is adjusted correspondingly. For example, studies of the Xe + CsI collisions during the 2023 Xe run were performed at Xe beam energies of 3.0 AGeV and 3.8 AGeV with the SP-41 current set to 1395 and 1720 A, respectively.

A vacuum beam pipe was integrated into the experimental setup in order to minimize the amount of scattering material in the path of the heavy ion beam. Vacuum in the entire beam pipe at the BM@N setup is achieved by a single roots pump installed upstream of the 1K200 quadrupole lens. The pressure maintained during the experiment is at the level of $10^{-4}\,Torr$. The ISO-K vacuum standard is adopted for flange connections. The stainless beam pipe with a diameter of $200\,mm$ is used in the beam transport line through the 1K200 and 2K200 quadrupole lenses and through the VKM and SP-57 corrective magnets up to the target. The vacuum level is monitored by two vacuum gauges, the data from which are recorded in the Slow Control System. The last $5\,m$ long part of the beam pipe before the target includes vacuum boxes containing the beam detectors described in the next section: two 3-way boxes for profilometers, three 3-way boxes for the Silicon Beam Tracker detectors and three 6-way boxes for the BC1, BC2, and VC trigger counters. All boxes located outside the magnetic field of the SP-41 analyzing magnet are made of stainless steel, while the vacuum pipe components, which are close to the target and placed in the magnet, are made of aluminum.

The bending of the beam ion trajectories by the magnetic field leads to a deflection from a straight line resulting in a few $mm$ displacement in the X direction at the target location. During the assembly of the beam pipe vacuum elements, an adjustment is carried out in order to compensate for this deflection. For that purpose the corresponding grooves for the vacuum box O-rings are made slightly wider than dictated by the ISO standard and allow for slight off-center shifts of the vacuum pipe components. The target flange assembly is also made of aluminum as well as an ISO 240 to $66\,mm$ vacuum adapter that provides a connection to the $4.5\,m$ long vacuum pipe that follows the target. This pipe is made of carbon fiber and consists of four straight sections of different lengths connected to each other by flangeless carbon fiber connections, which provide the possibility to align sections at slight angles with respect to each other as shown in Figs. 3 and  4. The carbon beam pipe is suspended on two supports also made of carbon fiber and installed on two GEM detectors, the one closest to the target and the other most downstream. The supports have adjustment units for precise positioning of the carbon beam pipe on the beam axis (Fig. 4). The carbon beam pipe is designed to sustain vacuum up to $10^{-4}\,Torr$. In the straight segments its thickness is about $1\,mm$, while in flangeless connections it reaches $2\,mm$.

The last section of the beam pipe has a length of approximately $3.2\,m$ and provides vacuum along the beam trajectory through the Outer Tracker system. It consists of three cylindrical segments with lengths of $1.2$, $1.0$ and $1.0\,m$, made of aluminum tube with an outer diameter of $125\,mm$ and a wall thickness of $1.5\,mm$. At the end of this section, the vacuum line is closed by a $100\,\mu m$ thick titanium membrane installed in a frame after the adapter ($d=125/150\,mm$).

The target station is located at the end of the second beam pipe section. It is designed to provide the possibility to insert a target in the beam line inside the vacuum volume and to interchange several targets without breaking the vacuum. A 3d model of the target station is presented in Fig. 6. An aluminum flange of $240\,mm$ in diameter serves as a holder of the target assembly elements and as an adapter between the beam pipe upstream of the target station and the first section of the carbon beam pipe. On the outer part of this flange, four pneumatic cylinders are installed allowing four target frames to be alternately moved in and out of the beam. The pneumatic cylinders can be remotely operated, and an optocoupler sensor is used to control the position of the target frames via a dedicated electronic module.

The part of the target assembly placed inside the vacuum has a centering frame, which fits into the inner part of the first section of the carbon beam pipe. The targets are installed in four petals. In the normal state, all the petals are leaning along the axis direction of the beam pipe. The retaining pins, made of carbon fiber, are $300\,mm$ long and $3\,mm$ in diameter.

In the 2023 Xe run, three disk targets with a diameter of $3.2\,cm$ were used: $1.75\,mm$ thick CsI, $0.85\,mm$ thick CsI, and $1.02\,mm$ thick Ge. One frame of the target assembly was left empty and was used to evaluate the background level caused by the interaction of beam particles with the structural elements of the target station.

The SP-41 dipole magnet with large acceptance is used in the spectrometer as an analyzing magnet to measure the momenta of produced particles and beam fragments. During the preparation of the magnet for the BM@N experiment, the original configuration of the SP-41, used in previous experiments with a streamer chamber, was significantly upgraded. In particular, the camera hole in the upper pole was filled with steel to improve the uniformity of the magnetic field, and the distance between the poles was increased by approximately $30\,cm$ to provide the space required by the BM@N GEM chambers. The dimensions of the SP-41 pole in X and Z directions are about 1.4 and $2.5\,m$, respectively, while the vertical distance between the upper and lower poles after the upgrade is $1.07\,m$ (Fig. 7). In the BM@N setup, the magnet is centered on the beam line. In the X coordinate the beam axis goes through the magnet close to the center of the poles, while vertically the beam axis is shifted closer to the lower pole by approximately $40\,mm$. The leading edge of the pole defines the origin of the Z axis, and the target is installed inside the SP-41 magnet at this position.

Determination of the momentum of the produced particles requires a detailed knowledge of the value and orientation of the magnetic field. After the upgrade of the SP-41, field measurements were performed by means of planar and 3D Hall probes SP41_2015 . In addition, the shape of the field was calculated by the TOSCA code using the known configuration of the yoke and coil materials. In order to obtain the field map for a wider X,Y,Z range and with smaller steps, the magnetic field measurement was repeated prior to the 2023 Xe run. The measurements with 3D Hall probes covered $(-156,+145\,cm)$, $(-38,+54\,cm)$, $(-162,+439\,cm)$ and were performed in $(126\times 47\times 241)$ points in X, Y, Z coordinates, respectively, allowing one to construct the field map on a $2.4\times 2.0\times 2.5\,cm^{3}$ three-dimensional grid (Fig. 7). During simulation and event reconstruction, the magnetic field components at a given (x,y,z) point are calculated by linear interpolation over eight neighboring measured nodes. The measurements of the field map were performed for four values of the current: 900, 1300, 1600, and $1900\,A$.

Each half-plane of the FSD forms an independent detector incorporating the following systems: coordinate modules based on DSSD, electronics cross-board, suspension and precise positioning mechanics, cable patch panel, air cooling, temperature monitors, light and EM shield. The top and bottom halves of each plane are made structurally identical and interchangeable. In addition, the design allows vertical shift of the half-planes during assembly in order to provide the possibility to mount/dismount the planes regardless of the installed beam pipe and to minimize the chances of its mechanical damage. In the working position, the upper and lower half-planes form a single coordinate system with active regions overlapping along the Y coordinate. In the center of each plane there is an insensitive $57\times 57\,mm^{2}$ zone which makes room for the beam pipe. A top view of the assembled eight half-planes around the beam pipe inside the SP-41 magnet is shown in Fig. 14.

The first plane consists of 6 modules, each of which uses one DSSD with dimensions of $93\times 63\times 0.32\,mm^{3}$ positioned in such a way that the long side is aligned with the Y coordinate. The detector modules of the remaining three coordinate planes use two $63\times 63\times 0.32\,mm^{3}$ DSSDs mounted on a common frame with an accuracy of $\pm 20\,\mu m$. There, the strips of the same type of one DSSD are connected to the strips of another DSSD by US-bonding with an aluminum wire of $25\,\mu m$ in diameter. Table  3 provides information about the number of modules and electronic components in each FSD plane.

The DSSDs with dimensions $63\times 63\times 0.32\,mm^{3}$ and $93\times 63\times 0.32\,mm^{3}$ were manufactured at RIMST (Zelenograd, Russia) and ZNTC (Zelenograd, Russia), respectively. The detector material is high-resistivity silicon wafers with diameters of 4” and 6”, produced by the Float Zone method ($\rho>5\,k\Omega\times cm$). Each side, $p^{+}$ and $n^{+}$, contains 640 strips. The strip spacing is 95 and $103\,\mu m$, respectively, and the relative angle between the strips on the two sides is $2.5^{\circ}$. The detectors are positioned in such a way that the strips of the $p^{+}$ side are aligned with the Y axis.

Fig. 15 shows a module with two DSSDs and a demonstration of US-bonding. A diagram of the FEE is presented in Fig. 16. The detector topology (DC) does not contain integrated bias resistors and capacitors for DC decoupling of the strips from the inputs of the readout electronics. The role of the RC-bias element in the DC circuit is performed by the integrated Pitch-Adapter (PA), which also performs the matching of the strip pitch with the pad topology of inputs in the FEE ASIC. The PAs, also manufactured at ZNTC, are based on a silicon-on-sapphire structure. Each PA has 640 RC channels with $1\,M\Omega$ polysilicon bias resistors and $120\,pF/100\,V$ integral capacitors. The PA-640 integrated circuits have low leakage currents (less than $10\,pA/capacitor/100\,V$) and an electrical breakdown value of $150\,V$, which corresponds to an electric field strength in the capacitor of more than $3\,MV/cm$.

After passing the PA, the signals from the $p^{+}$ and $n^{+}$ strips of the detector are fed to the inputs of a 128-channel specialized integrated circuit VATAGP7.1 (IDEAS, Norway) FEE_IDEAS . Each electronic registration channel has a charging amplifier ($\sigma$ - 200 $e$), a pulse shaper (peaking time $t_{s}=500\,ns$), and a memory capacitor, which stores the pulse amplitude at the trigger time. The ASIC also uses an analog multiplexer that channels 128 inputs into 1 output sent to the readout in the DAQ by ADC. Two printed circuit boards are used in each FSD module in order to accommodate its input signals, one for the 640 negative polarity signals from the $n^{+}$ strips, the other for the 640 positive polarity signals from the $p^{+}$ strips. Correspondingly, 5 ASICs are mounted on each PCB, bonding into the pitch adapters and sealed with a compound.

After the assembly of the modules into a half-plane, the position and rotation angles of every DSSD with respect to geodetic markers on the half-plane housing is measured using the NORGAU NVM II-5040D video meter with an accuracy of $\pm 5\,\mu m$. The markers are subsequently used during the installation in order to bind the position of each detector to the common coordinate system of the experimental setup.

Fig. 17 illustrates the distribution of hits in the 3^rd plane of the FSD observed in tests with cosmic rays and in the 2023 Xe run. Dark bands in the distribution indicate insensitive groups of 128 channels (1 chip). The number of such faulty chips at the end of the run was equal to 0, 1, 1, 8 for the 1^st, 2^nd, 3^rd and 4^th planes, respectively, which corresponds to 0.0, 1.0, 0.7 and $4.4\,\%$ of the channels. This malfunction can be due to the following reasons: 1) broken electrical contact in the transmission circuit from the chip (FEE buffer, cross-board connector, patch panel cable, long ADC-64 cable) 2) failure of the chip (no programming of the operating mode) or breakage of the US-bonding. Defects of the first type can be repaired, while the failures in the second group are of a permanent nature.

Triple-GEM detectors are located inside the SP-41 analyzing magnet downstream of the FSD. The full GEM tracking system configuration implemented in the 2023 Xe run consists of 14 detectors forming 7 tracking planes: 7 top detectors above the vacuum beam pipe and 7 bottom detectors below the pipe. Since the beam line inside the SP-41 is closer to the bottom pole of the magnet, in order to cover the maximum possible acceptance, the top and bottom detectors have been designed with different active area sizes, $163\times 45\,cm^{2}$ and $163\times 39\,cm^{2}$, respectively.

The left and right arms of the TOF400 system are placed at a distance of about 4 m from the target, symmetrically with respect to the beam. Each arm consists of two gas boxes (modules), each having 5 MRPC detectors (Fig. 20). The active area of one detector is $60\times 30\,cm^{2}$. Inside the box, the active areas of adjacent detectors overlap vertically by $50\,mm$, while the horizontal overlap of the gas boxes ensures crossing of the detector active area by $50\,mm$ as well. This makes the total active area of each of the two arms to be equal to $1.1\times 1.3\,m^{2}$, matching the geometrical acceptance of the $1.1\times 1.1\,m^{2}$ CSCs and covering a significant fraction of the GEM system acceptance. Each gas box is formed by an aluminum frame closed from the front and back sides by aluminum honeycomb plates, which provide sufficient rigidity while having small thickness in radiation lengths.

Fig. 21 shows a schematic cross-section of the TOF400 MRPC. The detector consists of three stacks inserted between two outer $1.5\,mm$ thick PCBs and separated by two inner PCBs, also $1.5\,mm$ thick. In order to add stiffness to the structure, fiberglass honeycombs with a thickness of $10\,mm$ were glued on the outer sides of the external PCBs. Each stack has 5 gas gaps between glass sheets, which are used as resistive electrodes. The two external glass sheets in a stack have a thickness of $400\,\mu m$, while the four internal sheets are $280\,\mu m$ thick. Fishing line as a spacer defines the $200\,\mu m$ gap between all the glass plates. High voltage is applied to the outer part of the external glass electrodes covered by conductive paint with the surface resistivity of about $2-10\,M\Omega/sq$. All internal glass electrodes are left electrically floating. Two PCBs with pickup readout pads are placed on both sides of the inner stack, one serving as the cathode readout plane, the other as the anode one. Correspondingly, the HV is applied in an alternating sequence, as shown on the right side of Fig. 21, in order to form a symmetrical configuration for the cathode and anode readout planes. Such a configuration was chosen to ensure that propagation of signals to the FEE has equal speed on positive and negative lines, thus preventing dispersion of the differential signal.

Readout pads are strips of $300\times 10\,mm^{2}$ arranged vertically with a $12.5\,mm$ pitch, making 48 readout strips in each PCB. A $2.5\,mm$ spacing between adjacent strips is introduced in order to reduce crosstalk between them. Signals from the strips are transferred to the front-end electronics by twisted pair cables. In order to achieve a better time resolution and determination of hit coordinate along the strip, the signals are read out from both ends of the strip.

The FEE of the TOF400 is based on the NINO amplifier/discriminator ASIC developed at CERN for the time-of-flight system of the ALICE experiment  TOF400_NINO_chip . The chip is processed on $0.25\,\mu m$ technology and has 8 input channels. Each channel includes an ultra-fast preamplifier with peaking time less than $1\,ns$, a discriminator with a minimum detection threshold of $10\,fC$, and an output stage which provides an LVDS output signal. The duration of the LVDS signal is proportional to the charge of the input signal and can be used for the amplitude-time correction. The 24-channel FEE board, which combines signal processing for three NINO chips, was developed at LHEP JINR  TOF400_FEE_board . In order to ensure optimal operation of the FEE, the boards are placed as close to the MRPC as possible and mounted on the front cover of the gas box. Measurements with a test signal from a generator showed an intrinsic time resolution of the FEE chain of about $7\,ps$. Additional features of the FEE board include the ability to remotely control the threshold levels of the NINO discriminators and to measure the supply voltage and temperature on the board via the RS-485 interface.

LVDS signals from the FEE boards are transmitted over a distance of up to $10\,m$ via a special cable without loss of time resolution. The signals are digitized in 72-channel time-to-digital converters (TDC72VHL) based on the HPTDC chip  TOF_HPTDC . The TDC72VHL were developed at LHEP JINR and operate in ultra high resolution mode with a binning of $23.4\,ps$. Such fine binning allows determining the leading and trailing edges of the input LVDS signals with high accuracy. The TDCs exhibit significant integral non-linearity, which, if not corrected, causes significant degradation of the time resolution. The method of uniform filling the TDC time window with random events (code density test) is used for non-linearity calibration of every channel of the TDC module. After applying the non-linearity correction, the intrinsic time resolution of individual TDC72VHL channels is equal to $20\,ps$ on average.

A full scale MRPC prototype with a complete readout chain and a $90\,\%\,C_{2}H_{2}F_{4}+5\,\%\,i-C_{4}H_{10}+5\,\%\,SF_{6}$ gas mixture was tested in the Nuclotron deutron beam  TOF400_TEST . A fast Cherenkov counter with a time resolution of $37\,ps$ was used as a start detector. The measured efficiency and time resolution as a function of high voltage for different levels of the NINO discriminator threshold are presented in Fig.  22. All the results include contributions from the front-end and data acquisition electronics. Based on the measured prototype performance, a high voltage of $11.5\,kV$ and a discriminator threshold of $120\,mV$ were chosen as the operating point of the TOF400 modules. With these settings, the dependence of efficiency and time resolution on the particle rate was studied with the prototype. The results of these tests are presented in Fig.  23. Monte Carlo simulations show that under the BM@N conditions, even at the highest heavy ion beam intensity, the particle flux in the TOF400 does not exceed $1\,kHz/cm^{2}$ for an Au+Au collision with the maximum energy and intensity of BM@N. Therefore, a time resolution better than $50\,ps$ and an efficiency higher than $95\,\%$ are expected.

The TOF700 wall is placed at about 7 meters from the target and has an active XY area of $3.2\times 2.2\,m^{2}$ defined to overlap with the geometrical acceptance of the Outer Tracker detectors ($2.2\times 1.5\,m^{2}$ CSC) as well as to provide substantial overlap with the GEM system acceptance. At the center of the TOF700 wall, there is an opening for the vacuum beam pipe. Since the density of hits from particles produced in heavy ion collisions is significantly higher in the region close to the beam, two types of MRPC detectors are used for the TOF700: “cold” – with an active area of $30\times 56\,cm^{2}$ and 16 readout strips of $18\times 560\,mm^{2}$ for the outer region with a low particle flux, and “warm” – with an active area of $16\times 35\,cm^{2}$ and 32 strips of $10\times 160\,mm^{2}$ for the region near the beam line. The horizontal orientation and size of the readout strips were dictated by the expected hit occupancy and the requirement of unambiguous matching of hits with particle tracks. The arrangement of the TOF700 MRPCs in the XY plane is shown in Fig. 24. The detectors are mounted on two sub-walls, which can slide relative to each other to facilitate access for installation and maintenance of the detectors. In addition, the MRPCs in each sub-wall are arranged in two layers in order to provide geometrical overlap between adjacent detectors.

“Cold” and “warm” MRPCs have a similar two-stack design with a single anode readout plane placed between the stacks. A schematic cross-section of a “cold” MRPC is shown in Fig.  25. Each stack is formed by six $0.67\,mm$ thick glass plates with the bulk resistivity of $2\times 10^{12}\,\Omega\times cm$. Fishing line spacers define a $0.3\,mm$ gap between the glass sheets. A graphite conductive coating with the surface resistivity of $\sim 1\,M\Omega/sq$ is painted on the outer surfaces of the external glass plates in order to apply both high voltage and ground connections. The anode readout plane is arranged on a $100\,\mu m$ one-sided PCB. Unipolar signals are taken from both ends of the strips, which makes it possible to determine the coordinate of the particle hit along the strip by measuring the time difference between the signals. Each detector is placed in an individual gas box, which is formed by a $2.5\,mm$ thick aluminum frame and two cover plates. One cover is made of a $2.5\,mm$ thick PCB and is designed to take out signal wires from the box volume to the readout electronics. The other cover is made of a $1.5\,mm$ thick aluminum sheet.

The design of “warm” MRPCs has only minor modifications. In order to increase their rate capability, the gas gaps and thickness of the glass plates in warm MRPCs are reduced to $0.22\,mm$ and $0.55\,mm$, respectively. Such a reduction leads to lower signal amplitudes due to increased anode strip – cathode capacity. To compensate for this signal weakening, the number of gaps in the chamber was increased from 10 to 12 (six gaps per stack).

The FEE boards are developed specially for BM@N. Signals from the MRPC are sent to the FEE over $50\,\Omega$ coaxial cables with MMCX connectors. The boards are based on the NINO ASICs, which, as already mentioned, process the signals in such a way that the duration of the LVDS output signals is proportional to the amplitude of the input signals, suitable for implementation of the time-over-threshold method. The output signals are transmitted to the digitizing module using DHR-78F connectors. A 64-channel VME TDC64VHLE time-to-digital converter based on the HPTDC chip is used for digitization. Using a special module (PWR&CTRL), it is possible to remotely control the power supply, discrimination threshold and hysteresis value in the FEE boards.

Prototypes of the “cold” and “warm” TOF700 detectors were tested in the secondary muon beam of the U-70 accelerator at IHEP (Protvino, Russia). The test was carried out at the “MUON” facility with a particle flux of about $1\,kHz/cm^{2}$ Kuzmin2019 . The test results of the “warm” MRPC prototype are shown in Fig. 26 and Fig. 27. The time resolution of the MRPCs with a complete chain of electronics (FEE and readout) is at the level of $60\,ps$. The efficiency is more than $95\,\%$.

Both TOF400 and TOF700 systems use the same non-flammable Freon rich gas mixture containing $90\,\%\,C_{2}H_{2}F_{4}$, $5\,\%\,i-C_{4}H_{10}$, and $5\,\%\,SF_{6}$. A simple open-loop gas system was designed for the BM@N experiment. This system is based on the MKS 1479A controllers produced by MKS Instruments, Inc. (Andover, Massachusetts, USA) for measuring and adjusting the absolute flow of components with an accuracy of $0.3\,\%$. The flow rate of the gas mixture can be adjusted in the range from $6\,l/h$ to $90\,l/h$.The typical operational flow is $21\,l/h$ which corresponds to the exchange of 2 volumes per day. The content of $O_{2}$ and $H_{2}O$ at the outlet of the system does not exceed $600\,ppm$ and $1000\,ppm$, respectively. The additional channel of the gas system is available to purge the system with nitrogen for cleaning and drying. A special PC program has been written to control the parameters of the gas system via the Ethernet interface.

The MRPC detector operates at very high voltages of $12\,kV$ and $15\,kV$ for the TOF400 and TOF700, respectively. On the other hand, the dark currents of the detector are quite small at the level of tens of $nA$. Also, the detector is very sensitive to voltage ripples due to the large capacitive coupling between the high voltage layer and the readout strips. Therefore, the high voltage system is subject to strict requirements for voltage stability and current measurement accuracy. The high voltage power supply systems for both TOF subsystems are based on commercially available Iseg modules (Iseg Spezialelektronik GmbH, Germany) and a system module specially designed for BM@N by HVSys (JINR, Dubna, Russia). Remote control of all elements of the system is organized via the Ethernet interface.

The main parameters of the TOF400 and TOF700 subsystems are summarized in Table  5.

The drift chambers, formerly used in the NA48 experiment at CERN DCH , have an octagonal shape with a transverse width of $2.9\,m$ (Fig. 28). Their fiducial area is about $4.5\,m^{2}$. The hole for the beam pipe in the center of the chamber has a diameter of $160\,mm$. The chambers are constructed with minimal amount of material along the beam direction, thus reducing multiple scattering effects.

Each chamber contains four X, Y, U, V coordinate planes with wire inclination angles with respect to the Y axis of $0^{\circ}$, $90^{\circ}$, $-45^{\circ}$ and $+45^{\circ}$, respectively. A schematic view of the drift cell geometry is shown in Fig. 29. In order to resolve left-right ambiguity of the hit position relative to the signal wire, every coordinate plane has two staggered rows of wires. Each coordinate plane has $2\times 256$ signal wires with a wire pitch of $10\,mm$. The central wires in the region of the beam pipe are split in two. The sense wires are grounded. The electric field is created by the negative voltage applied to two planes of field wires located on each side of the sense wire plane at a distance of $3\,mm$. The sense wires made of gold-plated tungsten have a diameter of $20\,\mu m$, while the gold-plated Ti-Cu field wires have a diameter of $120\,\mu m$. Thin Mylar foils ($22\,\mu m$) coated with graphite are used to shape the electric field in the drift cell. In addition, they serve as walls separating adjacent X, Y, U, V coordinate planes.

The chambers normally operate at a high voltage of about 2–$2.5\,kV$ between the field and sense wires, whereas the Mylar foils are kept at a negative voltage of 1–$1.5\,kV$. Typical gas amplification for such operating conditions is at the level of $2\times 10^{4}$. A drift distance of $5\,mm$ corresponds to a $\sim 100\,ns$ drift time, which ensures high rate capability of the detector.

The front-end amplifiers and discriminators developed for the readout of the DCH in the NA48 experiment DCH_el are used in the BM@N without modifications. The FEE cards are mounted on the frame of the drift chambers. The amplifiers are designed to provide accurate timing with minimal cross-talk between neighbouring channels. For pulses with a $10\,ns$ rise time, the cross-talk is suppressed with $\gtrsim 46\,dB$. The outputs of the amplifiers are AC-coupled to high-speed discriminators in LeCroy MVL407 IC units. The discriminator thresholds are set based on an external DC voltage and can be remotely controlled. The discriminator output is a differential ECL pulse with a $50\,ns$ width followed by $50\,ns$ of dead time. The output pulses are transmitted via $12\,m$ long twisted pair cables to TDC64VL VME modules, developed by AFI Electronics (Dubna, Russia). These 64-channel $100\,ps$ multihit TDCs provide a timestamp of the pulse front. The overall accuracy of the entire readout chain is about $1\,ns$.

The active area of the small CSC is $113\times 107\,cm^{2}$, while the large chambers have an active area of $219\times 145\,cm^{2}$. Both types of the CSC have similar design features. All chambers have one detection layer consisting of a plane of anode wires stretched between two cathode planes (see Figs. 30, 31). The anode wires form a horizontal grid with a step of $2.5\,mm$ in Y. They are made of gilded tungsten and have a diameter of $30\,\mu m$. In order to reduce anode wire deflection and to reinforce the flatness of the anode plane, vertical support wires are added to the mechanical design of the chambers. The support wires are made of stainless steel, have a diameter of $0.3\,mm$ and are insulated by a $0.8\,mm$ thick Teflon cladding.

The readout of induced signals is arranged on both front and back cathode planes made of PCBs with parallel metal strips. The inclination angles of the strips with respect to the vertical axis is 0 degrees (X coordinate) in one of the cathode planes and 15 degrees (Y coordinate) in the other. The pitch of the X and Y strips is $2.5\,mm$.

Due to the large multiplicity of charged particles in heavy ion collisions, the readout layer is divided into outer (cold) and inner (hot) zones, as shown in Fig.  31. The size of the inner zone is $-14<Y<14\,cm$ and $-24<Y<24\,cm$ in the small and large chambers, respectively. Each cathode plane in the small CSC is composed of two printed circuit boards, top and bottom. The cathode planes of the large chambers are assembled of eight PCBs, four in the top half of the plane and four in the bottom one.

To enhance the structure rigidity the PCBs are glued on support honeycomb panels. Furthermore, in order to prevent chamber deformation, the distance between the two cathode planes is fixed by additional spacers. The distance between cathode and anode planes was a subject of optimization and varies from chamber to chamber in the range from 3.4 to $3.8\,mm$. A larger gap increases the number of adjacent strips with induced signal above the threshold, the width of the cluster on average spans over 6 strips, i.e. $15\,mm$. On the other hand, a smaller than $3.4\,mm$ gap results in a higher probability of electric discharge. The cathode planes are grounded, and a high voltage of about $+2.4\,kV$ is applied to the anode wires.

The CSC front-end electronics is based on the same charge sensitive preamplifier chip VA163 as used for the GEM detectors. The multiplexed data from each FEE board are transmitted through a twisted pair flat cable to 12-bit analog-to-digital converter (ADC) modules read out by the data acquisition system. The full configuration of the Outer Tracker with six CSCs will have $\sim 30100$ readout channels and is planned to be integrated into the BM@N experimental setup in the next physics run.

All chambers of the Outer Tracker were operated with the $Ar(75\,\%)+C_{4}H_{10}(25\,\%)/C_{3}H_{8}O(vapor)$ gas mixture. The gas system (Fig. 32) consists of two parts: 1) the mixer system, which delivers a mixture of gases in a required ratio and pressure to downstream elements; 2) the distribution system, which delivers the gas in well defined quantities to the individual detectors. The power supply and readout module MKS 647C and mass flow controllers used in the gas distribution system are produced by MKS Instruments, Inc. (Andover, Massachusetts, USA).

The FHCal has a granular structure in the transverse and longitudinal planes. It consists of 54 separate modules in the transverse plane (see Fig. 33). The internal part of the FHCal consists of 34 small modules with transverse sizes of $15\times 15\,cm^{2}$ and a length equivalent to 4.0 nuclear interaction lengths. These modules are identical to the modules of the forward hadron calorimeters of the Multi-Purpose Detector (MPD) experiment at the NICA accelerator complex MPD_TDR . Each of the two outer lateral parts of the calorimeter contains 10 larger modules with a transverse size of $20\times 20\,cm^{2}$ and a length equivalent to 5.6 nuclear interaction lengths. These modules were initially constructed for the hadron calorimeter of the Compressed Baryonic Matter (CBM) experiment (FAIR, Darmstadt, Germany) CBM_PSD_TDR and are temporarily used in the BM@N experiment.

Beam ions that did not interact pass to a beam dump located behind the FHCal through the hole in the center of the calorimeter. The transverse size of the hole is $15\times 15\,cm^{2}$. This design feature is dictated by the requirement to protect internal modules and the front-end electronics of the FHCal against the high radiation dose and strong activation, typical for experiments with relativistic heavy ion beams.

The FHCal modules have a sampling structure and consist of lead/scintillator layers with a sampling ratio of 4:1 (the thickness of the lead plates and scintillator tiles are $16\,mm$ and $4\,mm$, respectively) and fulfill the compensation condition ($e/h=1$) for the hadron calorimeter. The small modules have 42 lead/scintillator layers, while the large modules have 60 such layers. To get rather high rigidity of the lead plates, they are made of lead-antimony alloy. The assembly of 60 (42) alternating layers of scintillator and lead plates is bound into one package by a $0.5\,mm$ thick stainless steel band tightened using a special tensioning mechanism. After tightening, the band is welded to additional steel plates inserted at the beginning, in the middle and at the end of the module (Fig. 34). Behind the tightening mechanism, a block of boron polystyrene with a thickness of $10\,cm$ is installed in the large modules. Once the package is assembled, it is closed by a cover box made of a $0.5\,mm$ thick stainless steel sheet.

The scintillator plates are made of polystyrene-based plastic scintillator produced by Uniplast (Vladimir, Russia). The light from the scintillator plates is collected by Kuraray Y11(200) wavelength shifting optical fiber glued into a $1.2\,mm$ deep groove on the surface of the scintillation plate and transported to the end of the module. The grooves in the scintillators of the large modules are circular, while those in the scintillators of the small modules are spiral. The end of each fiber on the scintillator side is coated with reflective paint. After the fiber is glued in the scintillator plate, the plate is wrapped in a Tyvek reflector. Outside of the scintillator plate, the fibers are placed in thin black plastic pipes to be optically shielded. When assembling the module, the plates are oriented in such a way that all optical fibers exit on the same side of the module (at the top). After that, groups of fibers from six consecutive scintillation plates are glued into individual optical connectors (7 and 10 groups in the small and large modules, respectively), which are placed on a panel mounted on the rear side of the module box (see Fig. 34). Thus, each of the large modules has ten longitudinal sections, and each of the small modules has seven sections. The longitudinal segmentation provides high homogeneity of light collection along the modules, a large dynamic range of the calorimeter response, and makes it possible to perform detailed energy calibration of the FHCal with cosmic muons FHCal_calib_cosmic .

The stability of the operation of the photodetectors and the calorimeter readout chain is controlled by a system of LEDs; one LED per calorimeter module. Correspondingly, the light from each LED is split to ten (seven) fibers, which are added into the optical connectors.

The weight of a single small and large module is about $200\,kg$ and $500\,kg$, respectively. The total weight of the FHCal is about 17 tons. The calorimeter is mounted on a special platform (Fig. 33 b), which is able to move the FHCal in X and Y directions.

The FHCal beam hole is covered with the FQH beam hodoscope. The main purpose of the FQH is to measure the charge of spectator fragments, which pass the beam hole of the calorimeter. In particular, the combined FHCal and FQH response allows one to estimate the collision centrality FHCal_FQH_centrality . The FQH consists of 16 quartz strips, which act as Cherenkov detectors. The size of the strips is $16\times 1\times 0.4\,cm^{3}$. The light from each FQH strip is viewed by two individual silicon photomultipliers mounted on both sides of the strip (see Fig. 35 a). The Hamamatsu S14160-3015PS MPPCs with a sensitive area of $3\times 3\,mm^{2}$ and an efficiency of $32\,\%$ are used as photodetectors. The hodoscope strips with photosensors are placed inside a single light tight box (see Fig. 35 b).

Four FEE boards, each of which can process eight input signals, are used in the readout of the whole FQH. The FEE boards incorporate signal amplifiers with two-gain outputs, the gains being $1\times$ and $4\times$. The low gain channel is used to cover maximum dynamic range up to the highest ion charge expected. The high gain channel is used to measure the charge of low–$Z$ fragments. Four TQDC-16 boards with a total of 64 channels are used to read out the two-gain outputs from each photodetector. Because the hodoscope is placed directly in the beamline, the charge calibration of the FQH strips is performed with ion beam. The FQH strips were tested on the $280\,MeV$ electron beam of ”Pakhra” synchrotron (LPI, Troitsk, Russia) and the light yield of about 5 photo-electrons on one MIP has been observed FQH_tests .

The ScWall is a large area detector aimed at measuring the charged particles in the forward rapidity region. It consists of an array of scintillating plates placed in an aluminum box. A view of the ScWall is shown in Fig. 36. The full detector size is $270\times 130\,cm^{2}$. The ScWall has 40 inner small ($7.5\times 7.5\times 1\,cm^{3}$) scintillator detectors (cells) and 138 large outer cells ($15\times 15\times 1\,cm^{3}$). In order to avoid radiation damage caused by the heavy ion beam, as well as to minimize background counts in other detectors, the very central part of the ScWall has a $15\times 15\,cm^{2}$ beam hole (see Fig. 36 b). The cells are made of polistirol-based scintillators manufactured by Uniplast (Vladimir, Russia).