Showing 1–50 of 67 results for author: Sloot, P

Integrated diode lasers for the generation of sub-GHz repetition rate frequency combs

Authors: Anzal Memon, Albert van Rees, Jesse Mak, Youwen Fan, Peter van der Slot, Hubertus Bastiaens, Klaus-J Boller

Abstract: We demonstrate absorber-free passive and hybrid mode-locking at sub-GHz repetition rates using a hybrid integrated extended cavity diode laser around 1550 nm. The laser is based on InP as gain medium and a long Si$_3$N$_4$ feedback circuit, with three highly frequency selective microring resonators. The feedback resonators not only increases the cavity length up to 0.6 m to achieve sub-GHz repetit… ▽ More We demonstrate absorber-free passive and hybrid mode-locking at sub-GHz repetition rates using a hybrid integrated extended cavity diode laser around 1550 nm. The laser is based on InP as gain medium and a long Si$_3$N$_4$ feedback circuit, with three highly frequency selective microring resonators. The feedback resonators not only increases the cavity length up to 0.6 m to achieve sub-GHz repetition rates but also serve as a dispersive narrowband mirror for sharp spectral filtering, which enables Fourier domain mode-locking. We observe passive mode-locking with repetition rates below 500 MHz, with $\approx$ 15 comb lines at around 0.2 mW total power. To stabilize the repetition rate, hybrid mode-locking is demonstrated by weak RF modulation of the diode current at frequencies around 500 MHz. The RF injection reduces the Lorentzian linewidth component from 8.9 kHz to a detection limited value around 300 mHz. To measure the locking range of the repetition rate, the injected RF frequency is tuned with regard to the passive mode-locking frequency and the injected RF power is varied. The locking range increases approximately as a square-root function of the injected RF power. At 1 mW injection a wide locking range of about 80 MHz is obtained. We observe the laser maintaining stable mode-locking also when the DC diode pump current is increased from 40 mA to 190 mA, provided that the cavity length is maintained constant with thermo-refractive tuning. △ Less

Submitted 30 May, 2024; originally announced May 2024.

Comments: This manuscript is under review for publication with optics express

Widely-tunable and narrow-linewidth hybrid-integrated diode laser at 637 nm

Authors: Lisa V. Winkler, Kirsten Gerritsma, Albert van Rees, Philip P. J. Schrinner, Marcel Hoekman, Ronald Dekker, Adriano R. do Nascimento Jr., Peter J. M. van der Slot, Christian Nölleke, Klaus-J. Boller

Abstract: We present hybrid-integrated extended cavity diode lasers tunable around 637 nm, with a gain-wide spectral coverage of 8 nm. This tuning range allows addressing the zero-phonon line of nitrogen vacancy centers and includes the wavelength of HeNe lasers (633 nm). The lasers provide wide mode-hop free tuning up to 97 GHz and a narrow intrinsic linewidth down to 10 kHz. The maximum output power is 2.… ▽ More We present hybrid-integrated extended cavity diode lasers tunable around 637 nm, with a gain-wide spectral coverage of 8 nm. This tuning range allows addressing the zero-phonon line of nitrogen vacancy centers and includes the wavelength of HeNe lasers (633 nm). The lasers provide wide mode-hop free tuning up to 97 GHz and a narrow intrinsic linewidth down to 10 kHz. The maximum output power is 2.5 mW in a single-mode fiber, corresponding to an on-chip power of 4.0 mW. Full integration and packaging in a standard housing with fiber pigtails provide high intrinsic stability and will enable integration into complex optical systems. △ Less

Submitted 8 April, 2024; originally announced April 2024.

Comments: 11 pages, 7 figures

Wakefields In Superconducting RF Cavities and The Impact on VUV Free-electron Laser Oscillator Performance

Authors: Alex H. Lumpkin, Henry P. Freund, Matthias Reinsch, Peter J. M. van der Slot

Abstract: The Fermilab Accelerator Science and Technology (FAST) facility is currently in operation with its linac based on TESLA-type superconducting rf cavities. Using a 3-MHz micropulse repetition rate with a long macropulse composed of up to 3000 micropulses, and with beam energies demonstrated at 300 MeV and projected to reach 800 MeV with two additional cryomodules, the feasibilities for a vacuum ultr… ▽ More The Fermilab Accelerator Science and Technology (FAST) facility is currently in operation with its linac based on TESLA-type superconducting rf cavities. Using a 3-MHz micropulse repetition rate with a long macropulse composed of up to 3000 micropulses, and with beam energies demonstrated at 300 MeV and projected to reach 800 MeV with two additional cryomodules, the feasibilities for a vacuum ultraviolet (VUV) and an extreme ultraviolet (EUV) free-electron laser oscillator (FELO) with the two energies are evaluated. We have used both the GINGER code with an oscillator module and the MINERVA/OPC code to assess FELO saturation prospects at 120 nm with a 5.0-cm-period undulator of 4.5-m length and the MINERVA/OPC code to assess the FELO at 13.4 nm with adjusted parameters. The simulation results support saturation at both of these wavelengths which are much shorter than the demonstrated shortest wavelength record of 168.6 nm from a storage-ring-based FELO. This indicates superconducting rf linac-driven FELOs can be extended into this VUV-EUV wavelength regime previously only reached with single-pass FEL configurations. In addition, emittance-dilution effects due to wakefields in the cavities and the resulting sub-macropulse centroid slew effects on FELO performance are addressed using MINERVA/OPC simulations for the first time. △ Less

Submitted 20 October, 2023; originally announced October 2023.

Comments: Journal submitted Phys.Rev.Accel.Beams (OA)

Report number: FERMILAB-PUB-23-581-AD-DI

Rate-Induced Transitions in Networked Complex Adaptive Systems: Exploring Dynamics and Management Implications Across Ecological, Social, and Socioecological Systems

Authors: Vítor V. Vasconcelos, Flávia M. D. Marquitti, Theresa Ong, Lisa C. McManus, Marcus Aguiar, Amanda B. Campos, Partha S. Dutta, Kristen Jovanelly, Victoria Junquera, Jude Kong, Elisabeth H. Krueger, Simon A. Levin, Wenying Liao, Mingzhen Lu, Dhruv Mittal, Mercedes Pascual, Flávio L. Pinheiro, Juan Rocha, Fernando P. Santos, Peter Sloot, Chenyang, Su, Benton Taylor, Eden Tekwa, Sjoerd Terpstra , et al. (5 additional authors not shown)

Abstract: Complex adaptive systems (CASs), from ecosystems to economies, are open systems and inherently dependent on external conditions. While a system can transition from one state to another based on the magnitude of change in external conditions, the rate of change -- irrespective of magnitude -- may also lead to system state changes due to a phenomenon known as a rate-induced transition (RIT). This st… ▽ More Complex adaptive systems (CASs), from ecosystems to economies, are open systems and inherently dependent on external conditions. While a system can transition from one state to another based on the magnitude of change in external conditions, the rate of change -- irrespective of magnitude -- may also lead to system state changes due to a phenomenon known as a rate-induced transition (RIT). This study presents a novel framework that captures RITs in CASs through a local model and a network extension where each node contributes to the structural adaptability of others. Our findings reveal how RITs occur at a critical environmental change rate, with lower-degree nodes tipping first due to fewer connections and reduced adaptive capacity. High-degree nodes tip later as their adaptability sources (lower-degree nodes) collapse. This pattern persists across various network structures. Our study calls for an extended perspective when managing CASs, emphasizing the need to focus not only on thresholds of external conditions but also the rate at which those conditions change, particularly in the context of the collapse of surrounding systems that contribute to the focal system's resilience. Our analytical method opens a path to designing management policies that mitigate RIT impacts and enhance resilience in ecological, social, and socioecological systems. These policies could include controlling environmental change rates, fostering system adaptability, implementing adaptive management strategies, and building capacity and knowledge exchange. Our study contributes to the understanding of RIT dynamics and informs effective management strategies for complex adaptive systems in the face of rapid environmental change. △ Less

Submitted 14 September, 2023; originally announced September 2023.

Comments: 25 pages, 4 figures, 1 box, supplementary information

MSC Class: 37G; 37N; 91B; 91C; 91D; 91E; 92D; 92D25; 92D40; 92F; 93A; 93A14; 93A16 ACM Class: I.6.3; I.6.m; J.3; J.4; J.m; K.4.2

Framework for developing quantitative agent based models based on qualitative expert knowledge: an organised crime use-case

Authors: Frederike Oetker, Vittorio Nespeca, Thijs Vis, Paul Duijn, Peter Sloot, Rick Quax

Abstract: In order to model criminal networks for law enforcement purposes, a limited supply of data needs to be translated into validated agent-based models. What is missing in current criminological modelling is a systematic and transparent framework for modelers and domain experts that establishes a modelling procedure for computational criminal modelling that includes translating qualitative data into q… ▽ More In order to model criminal networks for law enforcement purposes, a limited supply of data needs to be translated into validated agent-based models. What is missing in current criminological modelling is a systematic and transparent framework for modelers and domain experts that establishes a modelling procedure for computational criminal modelling that includes translating qualitative data into quantitative rules. For this, we propose FREIDA (Framework for Expert-Informed Data-driven Agent-based models). Throughout the paper, the criminal cocaine replacement model (CCRM) will be used as an example case to demonstrate the FREIDA methodology. For the CCRM, a criminal cocaine network in the Netherlands is being modelled where the kingpin node is being removed, the goal being for the remaining agents to reorganize after the disruption and return the network into a stable state. Qualitative data sources such as case files, literature and interviews are translated into empirical laws, and combined with the quantitative sources such as databases form the three dimensions (environment, agents, behaviour) of a networked ABM. Four case files are being modelled and scored both for training as well as for validation scores to transition to the computational model and application phase respectively. In the last phase, iterative sensitivity analysis, uncertainty quantification and scenario testing eventually lead to a robust model that can help law enforcement plan their intervention strategies. Results indicate the need for flexible parameters as well as additional case file simulations to be performed. △ Less

Submitted 21 July, 2023; originally announced August 2023.

Comments: 47 pages, 10 figures, 6 tables, appendix I-III

On-Chip Phase-Shift Induced Control of Supercontinuum Generation in a Dual-Core Si$\mathbf{_{3}}$N$\mathbf{_{4}}$ Waveguide

Authors: Lisi Xia, Peter J. M. van der Slot, Maximilian Timmerkamp, Bert Bastiaens, Carsten Fallnich, Klaus J. Boller

Abstract: We investigate on-chip spectral control of supercontinuum generation, taking advantage of the additional spatial degree of freedom in strongly-coupled dual-core waveguides. Using numerical integration of the multi-mode generalized nonlinear Schrödinger equation, we show that, with proper waveguide cross-section design, selective excitation of supermodes can vary the dispersion to its extremes, i.e… ▽ More We investigate on-chip spectral control of supercontinuum generation, taking advantage of the additional spatial degree of freedom in strongly-coupled dual-core waveguides. Using numerical integration of the multi-mode generalized nonlinear Schrödinger equation, we show that, with proper waveguide cross-section design, selective excitation of supermodes can vary the dispersion to its extremes, i.e., all-normal or anomalous dispersion can be selected via phase shifting in a Mach-Zehnder input circuit. The resulting control allows to provide vastly different supercontinuum spectra with the same waveguide circuit. △ Less

Submitted 8 July, 2023; originally announced July 2023.

Long-term absolute frequency stabilization of a hybrid-integrated InP-Si3N4 diode laser

Authors: Albert van Rees, Lisa V. Winkler, Pierre Brochard, Dimitri Geskus, Peter J. M. van der Slot, Christian Nölleke, Klaus-J. Boller

Abstract: Hybrid integrated diode lasers based on combining semiconductor optical amplifiers with low-loss Si3N4-based feedback circuits enable great laser performance for advanced photonic circuits. In particular, using high-Q Si3N4 ring resonators for frequency-selective feedback provides wide spectral coverage, mode-hop free tuning, and high frequency stability on short timescales, showing as ultra-narro… ▽ More Hybrid integrated diode lasers based on combining semiconductor optical amplifiers with low-loss Si3N4-based feedback circuits enable great laser performance for advanced photonic circuits. In particular, using high-Q Si3N4 ring resonators for frequency-selective feedback provides wide spectral coverage, mode-hop free tuning, and high frequency stability on short timescales, showing as ultra-narrow intrinsic linewidths. However, many applications also require long-term stability, which can be provided by locking the laser frequency to a suitable reference. We present the stabilization of a hybrid-integrated laser, which is widely tunable around the central wavelength of 1550 nm, to a fiber-based optical frequency discriminator (OFD) and to an acetylene absorption line. By locking the laser to the OFD, the laser's fractional frequency stability is improved down to 2.1$\cdot$10$^{-12}$ over an averaging time of 0.5 ms. For absolute stability over longer times of several days, we successfully lock the laser frequency to an acetylene absorption line. This limits the frequency deviations of the laser to a range of less than 12 MHz over 5 days. △ Less

Submitted 24 May, 2023; v1 submitted 24 February, 2023; originally announced February 2023.

Comments: 12 pages, 6 figures

Journal ref: IEEE Photonics Journal, Vol. 15, Issue 5, 1502408 (2023)

Hybrid integrated near UV lasers using the deep-UV Al2O3 platform

Authors: C. A. A. Franken, W. A. P. M. Hendriks, L. V. Winkler, M. Dijkstra, A. R. do Nascimento Jr, A. van Rees, M. R. S. Mardani, R. Dekker, J. van Kerkhof, P. J. M. van der Slot, S. M. García-Blanco, K. -J. Boller

Abstract: Hybrid integrated diode lasers have so far been realized using silicon, polymer, and silicon nitride (Si3N4) waveguide platforms for extending on-chip tunable light engines from the infrared throughout the visible range. Here we demonstrate the first hybrid integrated laser using the aluminum oxide (Al2O3) deep-UV capable waveguide platform. By permanently coupling low-loss Al2O3 frequency-tunable… ▽ More Hybrid integrated diode lasers have so far been realized using silicon, polymer, and silicon nitride (Si3N4) waveguide platforms for extending on-chip tunable light engines from the infrared throughout the visible range. Here we demonstrate the first hybrid integrated laser using the aluminum oxide (Al2O3) deep-UV capable waveguide platform. By permanently coupling low-loss Al2O3 frequency-tunable Vernier feedback circuits with GaN double-pass amplifiers in a hermetically sealed housing, we demonstrate the first extended cavity diode laser (ECDL) in the near UV. The laser shows a maximum fiber-coupled output power of 0.74 mW, corresponding to about 3.5 mW on chip, and tunes more than 4.4 nm in wavelength from 408.1 nm to 403.7 nm. Integrating stable, single-mode and tunable lasers into a deep-UV platform opens a new path for chip-integrated photonic applications. △ Less

Submitted 22 February, 2023; originally announced February 2023.

Comments: 14 pages, 3 figures

Considerations on wakefield effects in a VUV FELO driven by a superconducting tesla-type linac

Authors: Alex H. Lumpkin, Henry P. Freund, Peter Van der Slot

Abstract: The effects on beam dynamics from long-range and short-range wakefields from TESLA-type cavities are considered in regard to a proposed FEL oscillator (FE-LO) operating at 120 nm. This would be driven by the Fermilab Accelerator Science and Technology (FAST) linac at 300 MeV with a 3-MHz micropulse repetition rate. Our wakefield studies showed measurable effects on submacropulse centroid stability… ▽ More The effects on beam dynamics from long-range and short-range wakefields from TESLA-type cavities are considered in regard to a proposed FEL oscillator (FE-LO) operating at 120 nm. This would be driven by the Fermilab Accelerator Science and Technology (FAST) linac at 300 MeV with a 3-MHz micropulse repetition rate. Our wakefield studies showed measurable effects on submacropulse centroid stability and on submicropulse head-tail kicks that can lead to emittance degradation. In the case of the former, we use MINERVA/OPC to simulate the ~100-$μ$m centroid slew effects on the saturated output power levels of the FELO. △ Less

Submitted 24 August, 2022; originally announced August 2022.

Report number: FERMILAB-CONF-22-618-AD

Cascades towards noise-induced transitions on networks revealed using information flows

Authors: Casper van Elteren, Rick Quax, Peter Sloot

Abstract: Abrupt, system-wide transitions can be endogenously generated by seemingly stable networks of interacting dynamical units, such as mode switching in neuronal networks or public opinion changes in social systems. However, it remains poorly understood how such `noise-induced transitions' emerge from the interplay of network structure and dynamics on the network. Here, we report on two key roles that… ▽ More Abrupt, system-wide transitions can be endogenously generated by seemingly stable networks of interacting dynamical units, such as mode switching in neuronal networks or public opinion changes in social systems. However, it remains poorly understood how such `noise-induced transitions' emerge from the interplay of network structure and dynamics on the network. Here, we report on two key roles that nodes can play in the progression towards noise-induced tipping points. The models used are dynamical networks where the nodes are governed by the Boltzmann-Gibbs distribution, but the concept is easily generalized. First, so-called `initiator nodes' absorb and then transmit short-lived fluctuations to neighboring nodes, making them temporarily more dynamic. These neighbor nodes can then in turn transmit fluctuations to their neighbors, and so on, leading to a domino-effect where the more stable a node is (i.e., high average free energy barrier), the more neighbors are needed that have become temporarily dynamic. Interestingly, towards the tipping point we identify so-called `stabilizer nodes' whose state information becomes part of the long-term memory of the system, after which the domino-effect is reversed and settles the node in their new stable attractor. We validate these roles by targeted interventions that make tipping points more (or less) likely to begin or lead to systemic change. This opens up possibilities for understanding and controlling endogenously generated metastable behavior. △ Less

Submitted 29 May, 2024; v1 submitted 28 July, 2022; originally announced July 2022.

Comments: Should contain color

Guided-Acoustic Stimulated Brillouin Scattering in Silicon Nitride Photonic Circuits

Authors: Roel Botter, Kaixuan Ye, Yvan Klaver, Radius Suryadharma, Okky Daulay, Gaojian Liu, Jasper van den Hoogen, Lou Kanger, Peter van der Slot, Edwin Klein, Marcel Hoekman, Chris Roeloffzen, Yang Liu, David Marpaung

Abstract: Coherent optomechanical interaction between acoustic and optical waves known as stimulated Brillouin scattering (SBS) can enable ultra-high resolution signal processing and narrow linewidth lasers important for next generation wireless communications, precision sensing, and quantum information processing. While SBS has recently been studied extensively in integrated waveguides, many implementation… ▽ More Coherent optomechanical interaction between acoustic and optical waves known as stimulated Brillouin scattering (SBS) can enable ultra-high resolution signal processing and narrow linewidth lasers important for next generation wireless communications, precision sensing, and quantum information processing. While SBS has recently been studied extensively in integrated waveguides, many implementations rely on complicated fabrication schemes, using suspended waveguides, or non-standard materials such as As$_2$S$_3$. The absence of SBS in standard and mature fabrication platforms prevents large-scale circuit integration and severely limits the potential of this technology. Notably, SBS in standard silicon nitride integration platform is currently rendered out of reach due to the lack of acoustic guiding and the infinitesimal photo-elastic response of the material. In this paper, we experimentally demonstrate advanced control of backward SBS in multilayer silicon nitride waveguides. By optimizing the separation between two silicon nitride layers, we unlock gigahertz acoustic waveguiding in this platform for the first time, leading up to 15 $\times$ higher SBS gain coefficient than previously possible in silicon nitride waveguides. Using the same principle, we experimentally demonstrate on-demand inhibition of SBS by preventing acoustic guiding in the waveguide platform. We utilize the enhanced SBS gain to demonstrate a microwave photonic notch filter with high rejection (30 dB). We accomplish this in a low-loss, standard, and versatile silicon nitride integration platform without the need of suspending the SBS-active waveguide or hybrid integration with other materials. △ Less

Submitted 15 February, 2022; v1 submitted 1 December, 2021; originally announced December 2021.

Comments: 21 pages, 5 figures

Three-dimensional, time-dependent analysis of high- and low-Q free-electron laser oscillators

Authors: Peter J. M. van der Slot, Henry P. Freund

Abstract: Free-electron lasers (FELs) have been designed to operate over virtually the entire electromagnetic spectrum from microwaves through x-rays and in a variety of configurations including amplifiers and oscillators. Oscillators can operate in both the low and high gain regime and are typically used to improve the spatial and temporal coherence of the light generated. We will discuss various FEL oscil… ▽ More Free-electron lasers (FELs) have been designed to operate over virtually the entire electromagnetic spectrum from microwaves through x-rays and in a variety of configurations including amplifiers and oscillators. Oscillators can operate in both the low and high gain regime and are typically used to improve the spatial and temporal coherence of the light generated. We will discuss various FEL oscillators ranging from systems with high-quality resonators combined with low-gain undulators to systems with a low-quality resonator combined with a high-gain undulator line. The FEL gain code MINERVA and wavefront propagation code OPC are used to model the FEL interaction within the undulator and the propagation in the remainder of the oscillator, respectively. We will not only include experimental data for the various systems for comparison when available, but also present for selected cases how the two codes can be used to study the effect of mirror aberrations and thermal mirror deformation on FEL performance. △ Less

Submitted 6 May, 2021; originally announced May 2021.

Functional structure in production networks

Authors: Carolina Mattsson, Frank W. Takes, Eelke M. Heemskerk, Cees Diks, Gert Buiten, Albert Faber, Peter M. A. Sloot

Abstract: Production networks are integral to economic dynamics, yet dis-aggregated network data on inter-firm trade is rarely collected and often proprietary. Here we situate company-level production networks among networks from other domains according to their local connectivity structure. Through this lens, we study a regional and a national network of inferred trade relationships reconstructed from Dutc… ▽ More Production networks are integral to economic dynamics, yet dis-aggregated network data on inter-firm trade is rarely collected and often proprietary. Here we situate company-level production networks among networks from other domains according to their local connectivity structure. Through this lens, we study a regional and a national network of inferred trade relationships reconstructed from Dutch national economic statistics and re-interpret prior empirical findings. We find that company-level production networks have so-called functional structure, as previously identified in protein-protein interaction (PPI) networks. Functional networks are distinctive in their over-representation of closed squares, which we quantify using an existing measure called spectral bipartivity. Shared local connectivity structure lets us ferry insights between domains. PPI networks are shaped by complementarity, rather than homophily, and we use multi-layer directed configuration models to show that this principle explains the emergence of functional structure in production networks. Companies are especially similar to their close competitors, not to their trading partners. Our findings have practical implications for the analysis of production networks and a thorough understanding of their local connectivity structure will help us better reason about the micro-economic mechanisms behind their routine function, failure, and growth. △ Less

Submitted 29 March, 2021; originally announced March 2021.

Comments: 20 pages, 5 figures

Journal ref: Frontiers in Big Data 4 (2021)

Inferring temporal dynamics from cross-sectional data using Langevin dynamics

Authors: Pritha Dutta, Rick Quax, Loes Crielaard, Peter M. A. Sloot

Abstract: Cross-sectional studies are widely prevalent since they are more feasible to conduct compared to longitudinal studies. However, cross-sectional data lack the temporal information required to study the evolution of the underlying processes. Nevertheless, this is essential to develop predictive computational models which is the first step towards causal modelling. We propose a method for inferring c… ▽ More Cross-sectional studies are widely prevalent since they are more feasible to conduct compared to longitudinal studies. However, cross-sectional data lack the temporal information required to study the evolution of the underlying processes. Nevertheless, this is essential to develop predictive computational models which is the first step towards causal modelling. We propose a method for inferring computational models from cross-sectional data using Langevin dynamics. This method can be applied to any system that can be described as effectively following a free energy landscape, such as protein folding, stem cell differentiation and reprogramming, and social systems involving human interaction and social norms. A crucial assumption in our method is that the data-points are gathered from a system in (local) equilibrium. The result is a set of stochastic differential equations which capture the temporal dynamics, by assuming that groups of data-points are subject to the same free energy landscape and amount of noise. Our method is a 'baseline' method which initiates the development of computational models which can be iteratively enhanced through the inclusion of expert knowledge. We validate the proposed method against two population-based longitudinal datasets and observe significant predictive power in comparison with random choice algorithms. We also show how the predictive power of our 'baseline' model can be enhanced by incorporating domain expert knowledge. Our method addresses an important obstacle for model development in fields dominated by cross-sectional datasets. △ Less

Submitted 23 February, 2021; originally announced February 2021.

Comments: 17 pages, 3 figures, "The code for the proposed method is written in Mathematica programming language and is available at https://github.com/Pritha17/langevin-crosssectional"

Variable Polarization Control in Free-Electron Lasers

Authors: H. P. Freund, P. J. M. van der Slot

Abstract: Free-electron lasers (FELs) over virtually the entire electromagnetic spectrum from microwaves through ultraviolet through hard x-rays that are either seeded or start from noise. FELs can produce a variety of different optical polarizations of the output radiation ranging from linear through elliptic to circular polarization depending upon the characteristics of the undulators used. For example, x… ▽ More Free-electron lasers (FELs) over virtually the entire electromagnetic spectrum from microwaves through ultraviolet through hard x-rays that are either seeded or start from noise. FELs can produce a variety of different optical polarizations of the output radiation ranging from linear through elliptic to circular polarization depending upon the characteristics of the undulators used. For example, x-ray FELs use long undulator lines composed of a series of relatively short undulators. Most such FELs use linearly polarized undulators due to the ease of manufacture and tuning; hence the optical output is linearly polarized. However, elliptic or circular polarizations are possible by varying the orientation of the undulators along the line. Alternately, APPLE-II or Delta undulator designs allow for producing undulating magnetic fields with arbitrary polarizations. Here, we present a three-dimensional, time-dependent formulation that self-consistently models two independent optical polarizations and, therefore, completely treats any given sequence or combination of undulator, undulator imperfections, and undulator degradation There are two principal characteristics of the formulation that underpin this capability. In the first place, the particle trajectories are integrated by means of the full Lorentz force equations using three-dimensional analytic models of the undulators fields. This permits an accurate model of the interaction of the electrons with a large variety of undulator fields and orientations. In the second place, the formulation allows the electrons to couple simultaneously to two independent polarizations of the electromagnetic wave and, therefore, allows the optical polarization to evolve self-consistently along the undulator line. After first describing the numerical model, we proceed to give some examples using different undulator configurations that are of interest. △ Less

Submitted 16 December, 2020; originally announced December 2020.

Comments: 9 pages, 8 figures

High-purity microwave generation using a dual-frequency hybrid integrated semiconductor-dielectric waveguide laser

Authors: Jesse Mak, Albert van Rees, Rob E. M. Lammerink, Dimitri Geskus, Youwen Fan, Peter J. M. van der Slot, Chris G. H. Roeloffzen, Klaus-J. Boller

Abstract: We present an integrated semiconductor-dielectric hybrid dual-frequency laser operating in the 1.5 $μ$m wavelength range for microwave and terahertz (THz) generation. Generating a microwave beat frequency near 11 GHz, we observe a record-narrow intrinsic linewidth as low as about 2 kHz. This is realized by hybrid integration of a single diode amplifier based on indium phosphide (InP) with a long,… ▽ More We present an integrated semiconductor-dielectric hybrid dual-frequency laser operating in the 1.5 $μ$m wavelength range for microwave and terahertz (THz) generation. Generating a microwave beat frequency near 11 GHz, we observe a record-narrow intrinsic linewidth as low as about 2 kHz. This is realized by hybrid integration of a single diode amplifier based on indium phosphide (InP) with a long, low-loss silicon nitride (Si$_3$N$_4$) feedback circuit to extend the cavity photon lifetime, resulting in a cavity optical roundtrip length of about 30 cm on a chip. Simultaneous lasing at two frequencies is enabled by introducing an external control parameter for balancing the feedback from two tunable, frequency-selective Vernier mirrors on the Si$_3$N$_4$ chip. Each frequency can be tuned with a wavelength coverage of about 80 nm, potentially allowing for the generation of a broad range of frequencies in the microwave range up to the THz range. △ Less

Submitted 24 November, 2020; originally announced December 2020.

Journal ref: OSA Continuum, Vol. 4, Issue 8, pp. 2133-2142 (2021)

A hybrid-integrated diode laser in the visible spectral range

Authors: Cornelis A. A. Franken, Albert van Rees, Lisa V. Winkler, Youwen Fan, Dimitri Geskus, Ronald Dekker, Douwe H. Geuzebroek, Carsten Fallnich, Peter J. M. van der Slot, Klaus-J. Boller

Abstract: Generating visible light with wide tunability and high coherence based on photonic integrated circuits is of high interest for applications in biophotonics, precision metrology and quantum technology. Here we present the first demonstration of a hybrid-integrated diode laser in the visible spectral range. Using an AlGaInP optical amplifier coupled to a low-loss Si3N4 feedback circuit based on micr… ▽ More Generating visible light with wide tunability and high coherence based on photonic integrated circuits is of high interest for applications in biophotonics, precision metrology and quantum technology. Here we present the first demonstration of a hybrid-integrated diode laser in the visible spectral range. Using an AlGaInP optical amplifier coupled to a low-loss Si3N4 feedback circuit based on microring resonators, we obtain a spectral coverage of 10.8 nm around 684.4 nm wavelength with up to 4.8 mW output power. The measured intrinsic linewidth is 2.3$\pm$0.2 kHz. △ Less

Submitted 14 June, 2021; v1 submitted 8 December, 2020; originally announced December 2020.

Comments: 8 pages, 6 figures

Journal ref: Optics Letters, Vol. 46, Issue 19, pp. 4904-4907 (2021)

Analysis of Ultra-Short Bunches in Free-Electron Lasers

Authors: Lawrence Campbell, Henry Freund, James Henderson, Brian McNeil, Piotr Traczykowski, Peter van der Slot

Abstract: Free-electron lasers (FELs) operate at wavelengths from millimeter waves through hard x-rays. At x-ray wavelengths, FELs typically rely on self-amplified spontaneous emission (SASE). Typical SASE emission contains multiple temporal "spikes" which limit the longitudinal coherence of the optical output; hence, alternate schemes that improve on the longitudinal coherence of the SASE emission are of i… ▽ More Free-electron lasers (FELs) operate at wavelengths from millimeter waves through hard x-rays. At x-ray wavelengths, FELs typically rely on self-amplified spontaneous emission (SASE). Typical SASE emission contains multiple temporal "spikes" which limit the longitudinal coherence of the optical output; hence, alternate schemes that improve on the longitudinal coherence of the SASE emission are of interest. In this paper, we consnider electron bunches that are shorter than the SASE spike separation. In such cases, the spontaneously generated radiation consists of a single optical pulse with better longitudinal coherence than is found in typical SASE FELs. To investigate this regime, we use two FEL simulation codes. One (MINERVA) uses the slowly-varying envelope approximation(SVEA) which breaks down for extremely short pulses. The second (PUFFIN) is a particle-in-cell (PiC) simulation code that is considered to be a more complete model of the underlying physics and which is able to simulate very short pulses. We first anchor these codes by showing that there is substantial agreement between the codes in simulation of the SPARC SASE FEL experiment at ENEA Frascati. We then compare the two codes for simulations using electron bunch lengths that are shorter than the SASE slice separation. The comparisons between the two codes for short bunch simulations elucidate the limitations of the SVEA in this regime but indicate that the SVEA can treat short bunches that are comparable to the cooperation length. △ Less

Submitted 30 March, 2020; originally announced March 2020.

Comments: 8 pages, 11 figures. arXiv admin note: substantial text overlap with arXiv:1906.01996

Ring resonator enhanced mode-hop-free wavelength tuning of an integrated extended-cavity laser

Authors: Albert van Rees, Youwen Fan, Dimitri Geskus, Edwin J. Klein, Ruud M. Oldenbeuving, Peter J. M. van der Slot, Klaus-J. Boller

Abstract: Extending the cavity length of diode lasers with feedback from Bragg structures and ring resonators is highly effective for obtaining ultra-narrow laser linewidths. However, cavity length extension also decreases the free-spectral range of the cavity. This reduces the wavelength range of continuous laser tuning that can be achieved with a given phase shift of an intracavity phase tuning element. W… ▽ More Extending the cavity length of diode lasers with feedback from Bragg structures and ring resonators is highly effective for obtaining ultra-narrow laser linewidths. However, cavity length extension also decreases the free-spectral range of the cavity. This reduces the wavelength range of continuous laser tuning that can be achieved with a given phase shift of an intracavity phase tuning element. We present a method that increases the range of continuous tuning to that of a short equivalent laser cavity, while maintaining the ultra-narrow linewidth of a long cavity. Using a single-frequency hybrid integrated InP-Si3N4 diode laser with 120 nm coverage around 1540 nm, with a maximum output of 24 mW and lowest intrinsic linewidth of 2.2 kHz, we demonstrate a six-fold increased continuous and mode-hop-free tuning range of 0.22 nm (28 GHz) as compared to the free-spectral range of the laser cavity. △ Less

Submitted 19 December, 2019; originally announced December 2019.

Comments: 12 pages, 7 figures

Journal ref: Optics Express, Vol. 28, Issue 4, pp. 5669-5683 (2020)

Hybrid integrated semiconductor lasers with silicon nitride feedback circuits

Authors: Klaus-J. Boller, Albert van Rees, Youwen Fan, Jesse Mak, Rob E. M. Lammerink, Cornelis A. A. Franken, Peter J. M. van der Slot, David A. I. Marpaung, Carsten Fallnich, Jörn P. Epping, Ruud M. Oldenbeuving, Dimitri Geskus, Ronald Dekker, Ilka Visscher, Robert Grootjans, Chris G. H. Roeloffzen, Marcel Hoekman, Edwin J. Klein, Arne Leinse, René G. Heideman

Abstract: Hybrid integrated semiconductor laser sources offering extremely narrow spectral linewidth as well as compatibility for embedding into integrated photonic circuits are of high importance for a wide range of applications. We present an overview on our recently developed hybrid-integrated diode lasers with feedback from low-loss silicon nitride (Si3N4 in SiO2) circuits, to provide sub-100-Hz-level i… ▽ More Hybrid integrated semiconductor laser sources offering extremely narrow spectral linewidth as well as compatibility for embedding into integrated photonic circuits are of high importance for a wide range of applications. We present an overview on our recently developed hybrid-integrated diode lasers with feedback from low-loss silicon nitride (Si3N4 in SiO2) circuits, to provide sub-100-Hz-level intrinsic linewidths, up to 120 nm spectral coverage around 1.55 um wavelength, and an output power above 100 mW. We show dual-wavelength operation, dual-gain operation, laser frequency comb generation, and present work towards realizing a visible-light hybrid integrated diode laser. △ Less

Submitted 18 December, 2019; v1 submitted 25 November, 2019; originally announced November 2019.

Comments: 25 pages, 16 figures

Journal ref: Photonics, 7(1), 4 (2020)

Ultra-narrow linewidth hybrid integrated semiconductor laser

Authors: Youwen Fan, Albert van Rees, Peter J. M. van der Slot, Jesse Mak, Ruud Oldenbeuving, Marcel Hoekman, Dimitri Geskus, Chris G. H. Roeloffzen, Klaus-J. Boller

Abstract: We demonstrate a hybrid integrated and widely tunable diode laser with an intrinsic linewidth as narrow as 40 Hz, achieved with a single roundtrip through a low-loss feedback circuit that extends the cavity length to 0.5 meter on a chip. Employing solely dielectrics for single-roundtrip, single-mode resolved feedback filtering enables linewidth narrowing with increasing laser power, without limita… ▽ More We demonstrate a hybrid integrated and widely tunable diode laser with an intrinsic linewidth as narrow as 40 Hz, achieved with a single roundtrip through a low-loss feedback circuit that extends the cavity length to 0.5 meter on a chip. Employing solely dielectrics for single-roundtrip, single-mode resolved feedback filtering enables linewidth narrowing with increasing laser power, without limitations through nonlinear loss. We achieve single-frequency oscillation with up to 23 mW fiber coupled output power, 70-nm wide spectral coverage in the 1.55 $μ$m wavelength range with 3 mW output, and obtain more than 60 dB side mode suppression. Such properties and options for further linewidth narrowing render the approach of high interest for direct integration in photonic circuits serving microwave photonics, coherent communications, sensing and metrology with highest resolution. △ Less

Submitted 13 July, 2020; v1 submitted 17 October, 2019; originally announced October 2019.

Comments: 13 pages, and 11 figures

Journal ref: Optics Express, Vol. 28, Issue 15, pp. 21713-21728 (2020)

Comparison Between, and Validation Against an Experiment of, a Slowly-Varying Envelope Approximation Code and a Particle-in-Cell Simulation Code for Free-Electron Lasers

Authors: L. T. Campbell, H. P. Freund, J. Henderson, B. W. J. McNeil, P. Traczykowski, P. J. M. van der Slot

Abstract: Free-electron lasers (FELs) operate at wavelengths down to hard x-rays, and are either seeded or start from noise. There is increasing interest in x-ray FELs that rely on Self-Amplified Spontaneous Emission (SASE), and this involves increasing simulation activity in the design, optimization, and characterization of these x-ray FELs. Most of the simulation codes in use rely on the Slowly-Varying En… ▽ More Free-electron lasers (FELs) operate at wavelengths down to hard x-rays, and are either seeded or start from noise. There is increasing interest in x-ray FELs that rely on Self-Amplified Spontaneous Emission (SASE), and this involves increasing simulation activity in the design, optimization, and characterization of these x-ray FELs. Most of the simulation codes in use rely on the Slowly-Varying Envelope Approximation (SVEA) in which Maxwell's equations are averaged over the fast time scale resulting in relatively small computational requirements. While the SVEA codes are generally successful, the predictions of these codes sometimes differ in various aspects of the FEL interaction. In contrast, Particle-in-Cell (PiC) simulation codes do not average Maxwell's equations and are considered to be a more complete model of the underlying physics.Unfortunately, they require much longer run times than SVEA codes and have not been validated by comparison with experiment as often as the SVEA codes. In order to remedy this, and to resolve issues that arise due to different predictions between the SVEA codes, we present a comparison between one SVEA code (MINERVA) and a PiC simulation code (PUFFIN) with the experimental measurements obtained at the SPARC SASE FEL experiment at ENEA Frascati. The results show good agreement between the two codes and between the codes and the experiment. Since the formulations of the two codes share no common elements, this validates both formulations and demonstrates the capability to model the FEL interaction from the start of teh undulator through the undulator and into deep saturation. △ Less

Submitted 17 June, 2019; v1 submitted 4 June, 2019; originally announced June 2019.

Comments: 1 table, 3 figures. arXiv admin note: text overlap with arXiv:1611.01649

An X-Ray Regenerative Amplifier Free-Electron Laser Using Diamond Pinhole MIrrors

Authors: Henry P. Freund, Peter van der Slot, Yuri Shvyd'ko

Abstract: Free-electron lasers (FELs) have been built ranging in wavelength from long-wavelength oscillators using partial wave guiding through ultraviolet through hard x-ray FELs that are either seeded or start from noise (SASE). Operation in the x-ray spectrum has relied on single-pass SASE due either to the lack of seed lasers or difficulties in the design of x-ray mirrors. However, recent developments i… ▽ More Free-electron lasers (FELs) have been built ranging in wavelength from long-wavelength oscillators using partial wave guiding through ultraviolet through hard x-ray FELs that are either seeded or start from noise (SASE). Operation in the x-ray spectrum has relied on single-pass SASE due either to the lack of seed lasers or difficulties in the design of x-ray mirrors. However, recent developments in the production of diamond crystal Bragg reflectors point the way to the design of regenerative amplifiers (RAFELs) which are, essentially, low-Q x-ray free-electron laser oscillators (XFELOs) that out-couple a large fraction of the optical power on each pass. A RAFEL using a six-mirror resonator providing out-coupling of 90% or more through a pinhole in the first downstream mirror is proposed and analyzed using the MINERVA simulation code for the undulator interaction and the Optics Propagation Code (OPC) for the resonator. MINERVA/OPC has been used in the past to simulate infrared FEL oscillators. For the present purpose, OPC has been modified to treat Bragg reflection from diamond crystal mirrors. The six-mirror resonator design has been analyzed within the context of the LCLS-II beamline under construction at the Stanford Linear Accelerator Center and using the HXR undulator which is also to be installed on the LCLS-II beamline. Simulations have been run to optimize and characterize the properties of the RAFEL, and indicate that substantial powers are possible at the fundamental (3.05 keV) and third harmonic (9.15 keV). △ Less

Submitted 15 May, 2019; originally announced May 2019.

Comments: 9 pages, 14 figures

The dynamic importance of nodes is poorly predicted by static network features

Authors: Casper van Elteren, Rick Quax, Peter Sloot

Abstract: One of the most central questions in network science is: which nodes are most important? Often this question is answered using structural properties such as high connectedness or centrality in the network. However, static structural connectedness does not necessarily translate to dynamical importance. To demonstrate this, we simulate the kinetic Ising spin model on generated networks and one real-… ▽ More One of the most central questions in network science is: which nodes are most important? Often this question is answered using structural properties such as high connectedness or centrality in the network. However, static structural connectedness does not necessarily translate to dynamical importance. To demonstrate this, we simulate the kinetic Ising spin model on generated networks and one real-world weighted network. The dynamic impact of nodes is assessed by causally intervening on node state probabilities and measuring the effect on the systemic dynamics. The results show that structural features such as network centrality or connectedness are actually poor predictors of the dynamical impact of a node on the rest of the network. A solution is offered in the form of an information theoretical measure named integrated mutual information. The metric is able to accurately predict the dynamically most important node ('driver' node) in networks based on observational data of non-intervened dynamics. We conclude that the driver node(s) in networks are not necessarily the most well-connected or central nodes. Indeed, the common assumption of network structural features being proportional to dynamical importance is false. Consequently, great care should be taken when deriving dynamical importance from network data alone. These results highlight the need for novel inference methods that take both structure and dynamics into account. △ Less

Submitted 1 July, 2021; v1 submitted 14 April, 2019; originally announced April 2019.

Integrated frequency comb laser with narrow intrinsic optical linewidth based on a dielectric waveguide feedback circuit

Authors: Jesse Mak, Albert van Rees, Youwen Fan, Edwin J. Klein, Dimitri Geskus, Peter J. M. van der Slot, Klaus. -J. Boller

Abstract: We present an integrated hybrid semiconductor-dielectric (InP-Si$_3$N$_4$) waveguide laser that generates frequency combs at a wavelength around 1.5 $μ$m with a record-low intrinsic optical linewidth of 34 kHz. This is achieved by extending the cavity photon lifetime using a low-loss dielectric waveguide circuit. In our experimental demonstration, the on-chip, effective optical path length of the… ▽ More We present an integrated hybrid semiconductor-dielectric (InP-Si$_3$N$_4$) waveguide laser that generates frequency combs at a wavelength around 1.5 $μ$m with a record-low intrinsic optical linewidth of 34 kHz. This is achieved by extending the cavity photon lifetime using a low-loss dielectric waveguide circuit. In our experimental demonstration, the on-chip, effective optical path length of the laser cavity is extended to 6 cm. The resulting linewidth narrowing shows the high potential of on-chip, highly coherent frequency combs with direct electrical pumping, based on hybrid and heterogeneous integrated circuits making use of low-loss dielectric waveguides. △ Less

Submitted 18 February, 2019; originally announced February 2019.

Journal ref: Optics Express, Vol. 27, Issue 9, pp. 13307-13318 (2019)

A New Approach to Privacy-Preserving Clinical Decision Support Systems

Authors: Thomas Attema, Emiliano Mancini, Gabriele Spini, Mark Abspoel, Jan de Gier, Serge Fehr, Thijs Veugen, Maran van Heesch, Daniël Worm, Andrea De Luca, Ronald Cramer, Peter M. A. Sloot

Abstract: Background: Clinical decision support systems (CDSS) are a category of health information technologies that can assist clinicians to choose optimal treatments. These support systems are based on clinical trials and expert knowledge; however, the amount of data available to these systems is limited. For this reason, CDSSs could be significantly improved by using the knowledge obtained by treating p… ▽ More Background: Clinical decision support systems (CDSS) are a category of health information technologies that can assist clinicians to choose optimal treatments. These support systems are based on clinical trials and expert knowledge; however, the amount of data available to these systems is limited. For this reason, CDSSs could be significantly improved by using the knowledge obtained by treating patients. This knowledge is mainly contained in patient records, whose usage is restricted due to privacy and confidentiality constraints. Methods: A treatment effectiveness measure, containing valuable information for treatment prescription, was defined and a method to extract this measure from patient records was developed. This method uses an advanced cryptographic technology, known as secure Multiparty Computation (henceforth referred to as MPC), to preserve the privacy of the patient records and the confidentiality of the clinicians' decisions. Results: Our solution enables to compute the effectiveness measure of a treatment based on patient records, while preserving privacy. Moreover, clinicians are not burdened with the computational and communication costs introduced by the privacy-preserving techniques that are used. Our system is able to compute the effectiveness of 100 treatments for a specific patient in less than 24 minutes, querying a database containing 20,000 patient records. Conclusion: This paper presents a novel and efficient clinical decision support system, that harnesses the potential and insights acquired from treatment data, while preserving the privacy of patient records and the confidentiality of clinician decisions. △ Less

Submitted 3 December, 2018; v1 submitted 2 October, 2018; originally announced October 2018.

Comments: 15 pages, 4 figures

Surface acoustic waves for acousto-optic modulation in buried silicon nitride waveguides

Authors: Peter J. M. van der Slot, Marco A. G. Porcel, Klaus-J. Boller

Abstract: We theoretically investigate the use of Rayleigh surface acoustic waves (SAWs) for refractive index modulation in optical waveguides consisting of amorphous dielectrics. Considering low-loss Si$_3$N$_4$ waveguides with a standard core cross section of 4.4$\times$0.03 $μ$m$^2$ size, buried 8 $μ$m deep in a SiO$_2$ cladding we compare surface acoustic wave generation in various different geometries… ▽ More We theoretically investigate the use of Rayleigh surface acoustic waves (SAWs) for refractive index modulation in optical waveguides consisting of amorphous dielectrics. Considering low-loss Si$_3$N$_4$ waveguides with a standard core cross section of 4.4$\times$0.03 $μ$m$^2$ size, buried 8 $μ$m deep in a SiO$_2$ cladding we compare surface acoustic wave generation in various different geometries via a piezo-active, lead zirconate titanate film placed on top of the surface and driven via an interdigitized transducer (IDT). Using numerical solutions of the acoustic and optical wave equations, we determine the strain distribution of the SAW under resonant excitation. From the overlap of the acoustic strain field with the optical mode field we calculate and maximize the attainable amplitude of index modulation in the waveguide. For the example of a near-infrared wavelength of 840 nm, a maximum shift in relative effective refractive index of 0.7x10$^{-3}$ was obtained for TE polarized light, using an IDT period of 30 - 35 $μ$m, a film thickness of 2.5 - 3.5 $μ$m, and an IDT voltage of 10 V. For these parameters, the resonant frequency is in the range 70 - 85 MHz. The maximum shift increases to 1.2x10$^{-3}$, with a corresponding resonant frequency of 87 MHz, when the height of the cladding above the core is reduced to 3 $μ$m. The relative index change is about 300-times higher than in previous work based on non-resonant proximity piezo-actuation, and the modulation frequency is about 200-times higher. Exploiting the maximum relative index change of 1.2$\times$10$^{-3}$ in a low-loss balanced Mach-Zehnder modulator should allow full-contrast modulation in devices as short as 120 $μ$m (half-wave voltage length product = 0.24 Vcm). △ Less

Submitted 10 April, 2019; v1 submitted 9 October, 2017; originally announced October 2017.

Comments: 19 pages, 8 figures

Photo-induced second-order nonlinearity in stoichiometric silicon nitride waveguides

Authors: Marco A. G. Porcel, Jesse Mak, Caterina Taballione, Victoria K. Schermerhorn, Jörn P. Epping, Peter J. M. van der Slot, Klaus-J. Boller

Abstract: We report the observation of second-harmonic generation in stoichiometric silicon nitride waveguides grown via low-pressure chemical vapour deposition. Quasi-rectangular waveguides with a large cross section were used, with a height of 1 μm and various different widths, from 0.6 to 1.2 μm, and with various lengths from 22 to 74 mm. Using a mode-locked laser delivering 6-ps pulses at 1064 nm wavele… ▽ More We report the observation of second-harmonic generation in stoichiometric silicon nitride waveguides grown via low-pressure chemical vapour deposition. Quasi-rectangular waveguides with a large cross section were used, with a height of 1 μm and various different widths, from 0.6 to 1.2 μm, and with various lengths from 22 to 74 mm. Using a mode-locked laser delivering 6-ps pulses at 1064 nm wavelength with a repetition rate of 20 MHz, 15% of the incoming power was coupled through the waveguide, making maximum average powers of up to 15 mW available in the waveguide. Second-harmonic output was observed with a delay of minutes to several hours after the initial turn-on of pump radiation, showing a fast growth rate between 10$^{-4}$ to 10$^{-2}$ s$^{-1}$, with the shortest delay and highest growth rate at the highest input power. After this first, initial build-up, the second-harmonic became generated instantly with each new turn-on of the pump laser power. Phase matching was found to be present independent of the used waveguide width, although the latter changes the fundamental and second-harmonic phase velocities. We address the presence of a second-order nonlinearity and phase matching, involving an initial, power-dependent build-up, to the coherent photogalvanic effect. The effect, via the third-order nonlinearity and multiphoton absorption leads to a spatially patterned charge separation, which generates a spatially periodic, semi-permanent, DC-field-induced second-order susceptibility with a period that is appropriate for quasi-phase matching. The maximum measured second-harmonic conversion efficiency amounts to 0.4% in a waveguide with 0.9 x 1 μm$^2$ cross section and 36 mm length, corresponding to 53 μW at 532 nm with 13 mW of IR input coupled into the waveguide. The according $χ^{(2)}$ amounts to 3.7 pm/V, as retrieved from the measured conversion efficiency. △ Less

Submitted 30 October, 2017; v1 submitted 9 October, 2017; originally announced October 2017.

Comments: 20 pages, 10 figures

Information processing features can detect behavioral regimes of dynamical systems

Authors: Rick Quax, Gregor Chliamovitch, Alexandre Dupuis, Jean-Luc Falcone, Bastien Chopard, Alfons G. Hoekstra, Peter M. A. Sloot

Abstract: In dynamical systems, local interactions between dynamical units generate correlations which are stored and transmitted throughout the system, generating the macroscopic behavior. However a framework to quantify and study this at the microscopic scale is missing. Here we propose an 'information processing' framework based on Shannon mutual information quantities between the initial and future stat… ▽ More In dynamical systems, local interactions between dynamical units generate correlations which are stored and transmitted throughout the system, generating the macroscopic behavior. However a framework to quantify and study this at the microscopic scale is missing. Here we propose an 'information processing' framework based on Shannon mutual information quantities between the initial and future states. We apply it to the 256 elementary cellular automata (ECA), which are the simplest possible dynamical systems exhibiting behaviors ranging from simple to complex. Our main finding for ECA is that only a few features are needed for full predictability and that the 'information integration' (synergy) feature is always most predictive. Finally we apply the formalism to foreign exchange (FX) and interest-rate swap (IRS) time series data and find that the 2008 financial crisis marks a sudden and sustained regime shift (FX and EUR IRS) resembling tipping point behavior. The USD IRS market exhibits instead a slow and steady progression which appears consistent with the hypothesis that this market is (part of) the driving force behind the crisis. Our work suggests that the proposed framework is a promising way of predicting emergent complex systemic behaviors in terms of the local information processing of units. △ Less

Submitted 27 September, 2017; originally announced September 2017.

Studies of a Terawatt X-Ray Free-Electron Laser

Authors: H. P. Freund, P. J. M. van der SLot

Abstract: The possibility of constructing terawatt (TW) x-ray free-electron lasers (FELs) has been discussed using novel superconducting helical undulators [5]. In this paper, we consider the conditions necessary for achieving powers in excess of 1 TW in a 1.5 Å FEL using simulations with the MINERVA simulation code [7]. Steady-state simulations have been conducted using a variety of undulator and focusing… ▽ More The possibility of constructing terawatt (TW) x-ray free-electron lasers (FELs) has been discussed using novel superconducting helical undulators [5]. In this paper, we consider the conditions necessary for achieving powers in excess of 1 TW in a 1.5 Å FEL using simulations with the MINERVA simulation code [7]. Steady-state simulations have been conducted using a variety of undulator and focusing configurations. In particular, strong focusing using FODO lattices is compared with the natural, weak focusing inherent in helical undulators. It is found that the most important requirement to reach TW powers is extreme transverse compression of the electron beam in a strong FODO lattice. The importance of extreme focusing of the electron beam in the production of TW power levels means that the undulator is not the prime driver for a TW FEL, and simulations are also described using planar undulators that reach near-TW power levels. In addition, TW power levels can be reached using pure self-amplified spontaneous emission (SASE) or with novel self-seeding configurations when such extreme focusing of the electron beam is applied. △ Less

Submitted 29 March, 2018; v1 submitted 9 June, 2017; originally announced June 2017.

Comments: 10 pages, 12 figures

A temporal model for quasi-phase matching in high-order harmonic generation

Authors: Y. Tao, S. J. Goh, H. M. J. Bastiaens, P. J. M. van der Slot, S. G. Biedron, S. V. Milton, K. -J. Klaus

Abstract: We present a model for quasi-phase matching (QPM) in high-order harmonic generation (HHG). Using a one-dimensional description, we analyze the time-dependent, ultrafast wave-vector balance to calculate the on-axis harmonic output versus time, from which we obtain the output pulse energy. Considering, as an example, periodically patterned argon gas, as may be provided with a grid in a cluster jet,… ▽ More We present a model for quasi-phase matching (QPM) in high-order harmonic generation (HHG). Using a one-dimensional description, we analyze the time-dependent, ultrafast wave-vector balance to calculate the on-axis harmonic output versus time, from which we obtain the output pulse energy. Considering, as an example, periodically patterned argon gas, as may be provided with a grid in a cluster jet, we calculate the harmonic output during different time intervals within the drive laser pulse duration. We find that identifying a suitable single spatial period is not straightforward due to the complex and ultrafast plasma dynamics that underlies HHG at increased intensities. The maximum on-axis harmonic pulse energy is obtained when choosing the QPM period to phase match HHG at the leading edge of the drive laser pulse. △ Less

Submitted 13 December, 2016; originally announced December 2016.

Cluster size dependence of high-order harmonic generation

Authors: Y. Tao, R. Hagmeijers, H. M. J. Bastiaens, S. J. Goh, P. J. M. van der Slot, S. G. Biedron, S. V. Milton, K. -J. Boller

Abstract: We investigate high-order harmonic generation (HHG) from noble gas clusters in a supersonic gas jet. To identify the contribution of harmonic generation from clusters versus that from gas monomers, we measure the high-order harmonic output over a broad range of the total atomic number density in the jet (from 3*10^16 cm^{-3} to 3x10^18 cm{-3}) at two different reservoir temperatures (303 K and 363… ▽ More We investigate high-order harmonic generation (HHG) from noble gas clusters in a supersonic gas jet. To identify the contribution of harmonic generation from clusters versus that from gas monomers, we measure the high-order harmonic output over a broad range of the total atomic number density in the jet (from 3*10^16 cm^{-3} to 3x10^18 cm{-3}) at two different reservoir temperatures (303 K and 363 K). For the firrst time in the evaluation of the harmonic yield in such measurements, the variation of the liquid mass fraction, g, versus pressure and temperature is taken into consideration, which we determine, reliably and consistently, to be below 20% within our range of experimental parameters. By comparing the measured harmonic yield from a thin jet with the calculated corresponding yield from monomers alone, we find an increased emission of the harmonics when the average cluster size is less than 3000. Using g, under the assumption that the emission from monomers and clusters add up coherently, we calculate the ratio of the average single-atom response of an atom within a cluster to that of a monomer and find an enhancement of around 10 for very small average cluster size (~200). We do not find any dependence of the cut-off frequency on the composition of the cluster jet. This implies that HHG in clusters is based on electrons that return to their parent ions and not to neighbouring ions in the cluster. To fully employ the enhanced average single-atom response found for small average cluster sizes (~200), the nozzle producing the cluster jet must provide a large liquid mass fraction at these small cluster sizes for increasing the harmonic yield. Moreover, cluster jets may allow for quasi-phase matching, as the higher mass of clusters allows for a higher density contrast in spatially structuring the nonlinear medium. △ Less

Submitted 2 May, 2017; v1 submitted 29 November, 2016; originally announced November 2016.

Comments: 16 pages, 6 figures

Three-Dimensional, Time-Dependent Simulation of Free-Electron Lasers with Planar, Helical, and Elliptical Undulators

Authors: H. P. Freund, P. J. M. van der Slot, D. L. A. G. Grimminck, I. D. Setija, P. Falgari

Abstract: Free-electron lasers (FELs) have been built ranging in wavelength from long-wavelength oscillators using partial wave guiding through ultraviolet through hard x-ray that are either seeded or start from noise (SASE). In addition, FELs that produce different polarizations of the output radiation ranging from linear through elliptic to circular polarization are currently under study. In this paper, w… ▽ More Free-electron lasers (FELs) have been built ranging in wavelength from long-wavelength oscillators using partial wave guiding through ultraviolet through hard x-ray that are either seeded or start from noise (SASE). In addition, FELs that produce different polarizations of the output radiation ranging from linear through elliptic to circular polarization are currently under study. In this paper, we develop a three-dimensional, time-dependent formulation that is capable of modeling this large variety of FEL configurations including different polarizations. We employ a modal expansion for the optical field, i.e., a Gaussian expansion with variable polarization for free-space propagation. This formulation uses the full Newton-Lorentz force equations to track the particles through the optical and magnetostatic fields. As a result, arbitrary three-dimensional representations for different undulator configurations are implemented, including planar, helical, and elliptical undulators. In particular, we present an analytic model of an APPLE-II undulator to treat arbitrary elliptical polarizations. To model oscillator configurations, and allow propagation of the optical field outside the undulator and interact with optical elements, we link the FEL simulation with the optical propagation code OPC. We present simulations using the APPLE-II undulator model to produce elliptically polarized output radiation, and present a detailed comparison with recent experiments using a tapered undulator configuration at the Linac Coherent Light Source. Validation of the nonlinear formation is also shown by comparison with experimental results obtained in the SPARC SASE FEL experiment at ENEA Frascati, a seeded tapered amplifier experiment at Brookhaven National Laboratory, and the 10-kW Upgrade Oscillator experiment at the Thomas Jefferson National Accelerator Facility. △ Less

Submitted 5 November, 2016; originally announced November 2016.

Comments: 14 pages, double column, 20 figures

Coherent Cerenkov radiation and laser oscillation in a photonic crystal

Authors: T. Denis, M. V. van Dijk, J. H. H. Lee, R. van der Meer, A. Strooisma, P. J. M. van der Slot, W. L. Vos, K. J. Boller

Abstract: We demonstrate that photonic crystals can be used to generate powerful and highly coherent laser radiation when injecting a beam of free electrons. Using theoretical investigations we present the startup dynamics and coherence properties of such laser, in which gain is provided by matching the optical phase velocity in the photonic crystal to the velocity of the electron beam. We demonstrate that photonic crystals can be used to generate powerful and highly coherent laser radiation when injecting a beam of free electrons. Using theoretical investigations we present the startup dynamics and coherence properties of such laser, in which gain is provided by matching the optical phase velocity in the photonic crystal to the velocity of the electron beam. △ Less

Submitted 26 October, 2016; v1 submitted 23 August, 2016; originally announced August 2016.

Comments: 6 pages, 5 figures

Journal ref: Phys. Rev. A 94, 053852 (2016)

Stripping syntax from complexity: An information-theoretical perspective on complex systems

Authors: Rick Quax, Omri Har-Shemesh, Stefan Thurner, Peter M. A. Sloot

Abstract: Claude Shannons information theory (1949) has had a revolutionary impact on communication science. A crucial property of his framework is that it decouples the meaning of a message from the mechanistic details from the actual communication process itself, which opened the way to solve long-standing communication problems. Here we argue that a similar impact could be expected by applying informatio… ▽ More Claude Shannons information theory (1949) has had a revolutionary impact on communication science. A crucial property of his framework is that it decouples the meaning of a message from the mechanistic details from the actual communication process itself, which opened the way to solve long-standing communication problems. Here we argue that a similar impact could be expected by applying information theory in the context of complexity science to answer long-standing, cross-domain questions about the nature of complex systems. This happens by decoupling the domain-specific model details (e.g., neuronal networks, ecosystems, flocks of birds) from the cross-domain phenomena that characterize complex systems (e.g., criticality, robustness, tipping points). This goes beyond using information theory as a non-linear correlation measure, namely it allows describing a complex system entirely in terms of the storage, transfer, and modification of informational bits. After all, a phenomenon that does not depend on model details should best be studied in a framework that strips away all such details. We highlight the first successes of information-theoretic descriptions in the recent complexity literature, and emphasize that this type of research is still in its infancy. Finally we sketch how such an information-theoretic description may even lead to a new type of universality among complex systems, with a potentially tremendous impact. The goal of this perspective article is to motivate a paradigm shift in the young field of complexity science using a lesson learnt in communication science. △ Less

Submitted 11 March, 2016; originally announced March 2016.

Comments: 12 pages, 1 Fig, 30 References

MSC Class: 94A-02 ACM Class: F.0

Quantifying synergistic information using intermediate stochastic variables

Authors: Rick Quax, Omri Har-Shemesh, Peter M. A. Sloot

Abstract: Quantifying synergy among stochastic variables is an important open problem in information theory. Information synergy occurs when multiple sources together predict an outcome variable better than the sum of single-source predictions. It is an essential phenomenon in biology such as in neuronal networks and cellular regulatory processes, where different information flows integrate to produce a sin… ▽ More Quantifying synergy among stochastic variables is an important open problem in information theory. Information synergy occurs when multiple sources together predict an outcome variable better than the sum of single-source predictions. It is an essential phenomenon in biology such as in neuronal networks and cellular regulatory processes, where different information flows integrate to produce a single response, but also in social cooperation processes as well as in statistical inference tasks in machine learning. Here we propose a metric of synergistic entropy and synergistic information from first principles. The proposed measure relies on so-called synergistic random variables (SRVs) which are constructed to have zero mutual information about individual source variables but non-zero mutual information about the complete set of source variables. We prove several basic and desired properties of our measure, including bounds and additivity properties. In addition, we prove several important consequences of our measure, including the fact that different types of synergistic information may co-exist between the same sets of variables. A numerical implementation is provided, which we use to demonstrate that synergy is associated with resilience to noise. Our measure may be a marked step forward in the study of multivariate information theory and its numerous applications. △ Less

Submitted 19 October, 2016; v1 submitted 3 February, 2016; originally announced February 2016.

ACM Class: E.4; H.1.1; G.3

Deep Saturated Free Electron Laser Oscillators and Frozen Spikes

Authors: P. L. Ottaviani, S. Pagnutti, G. Dattoli, E. Sabia, V. Petrillo, P. Van Der Slot, S. Biedron, S. Milton

Abstract: We analyze the behavior of Free Electron Laser (FEL) oscillators operating in the deep saturated regime and point out the formation of sub-peaks of the optical pulse. They are very stable configurations, having a width corresponding to a coherence length. We speculate on the physical mechanisms underlying their growth and attempt an identification with FEL mode locked structures associated with Su… ▽ More We analyze the behavior of Free Electron Laser (FEL) oscillators operating in the deep saturated regime and point out the formation of sub-peaks of the optical pulse. They are very stable configurations, having a width corresponding to a coherence length. We speculate on the physical mechanisms underlying their growth and attempt an identification with FEL mode locked structures associated with Super Modes. Their impact on the intra-cavity nonlinear harmonic generation is also discussed along with the possibility of exploiting them as cavity out-coupler. △ Less

Submitted 27 January, 2016; originally announced January 2016.

Comments: 28 pages

Information geometric analysis of phase transitions in complex patterns: the case of the Gray-Scott reaction-diffusion model

Authors: Omri Har Shemesh, Rick Quax, Alfons G. Hoekstra, Peter M. A. Sloot

Abstract: The Fisher-Rao metric from Information Geometry is related to phase transition phenomena in classical statistical mechanics. Several studies propose to extend the use of Information Geometry to study more general phase transitions in complex systems. However, it is unclear whether the Fisher-Rao metric does indeed detect these more general transitions, especially in the absence of a statistical mo… ▽ More The Fisher-Rao metric from Information Geometry is related to phase transition phenomena in classical statistical mechanics. Several studies propose to extend the use of Information Geometry to study more general phase transitions in complex systems. However, it is unclear whether the Fisher-Rao metric does indeed detect these more general transitions, especially in the absence of a statistical model. In this paper we study the transitions between patterns in the Gray-Scott reaction-diffusion model using Fisher information. We describe the system by a probability density function that represents the size distribution of blobs in the patterns and compute its Fisher information with respect to changing the two rate parameters of the underlying model. We estimate the distribution non-parametrically so that we do not assume any statistical model. The resulting Fisher map can be interpreted as a phase-map of the different patterns. Lines with high Fisher information can be considered as boundaries between regions of parameter space where patterns with similar characteristics appear. These lines of high Fisher information can be interpreted as phase transitions between complex patterns. △ Less

Submitted 4 January, 2016; v1 submitted 7 December, 2015; originally announced December 2015.

Comments: 13 pages, 8 figures

Single-shot fluctuations in waveguided high-harmonic generation

Authors: S. J. Goh, Y. Tao, P. J. M. van der Slot, H. J. M. Bastiaens, J. Herek, S. G. Biedron, M. B. Danailov, S. V. Milton, K. -J. Boller

Abstract: For exploring the application potential of coherent soft x-ray (SXR) and extreme ultraviolet radiation (XUV) provided by high-harmonic generation, it is important to characterize the central output parameters. Of specific importance are pulse-to-pulse (shot-to-shot) fluctuations of the high-harmonic output energy, fluctuations of the direction of the emission (pointing instabilities), and fluctuat… ▽ More For exploring the application potential of coherent soft x-ray (SXR) and extreme ultraviolet radiation (XUV) provided by high-harmonic generation, it is important to characterize the central output parameters. Of specific importance are pulse-to-pulse (shot-to-shot) fluctuations of the high-harmonic output energy, fluctuations of the direction of the emission (pointing instabilities), and fluctuations of the beam divergence and shape that reduce the spatial coherence. We present the first single-shot measurements of waveguided high-harmonic generation in a waveguided (capillary-based) geometry. Using a capillary waveguide filled with Argon gas as the nonlinear medium, we provide the first characterization of shot-to-shot fluctuations of the pulse energy, of the divergence and of the beam pointing. We record the strength of these fluctuations vs. two basic input parameters, which are the drive laser pulse energy and the gas pressure in the capillary waveguide. In correlation measurements between single-shot drive laser beam profiles and single-shot high-harmonic beam profiles we prove the absence of drive laser beam-pointing-induced fluctuations in the high-harmonic output. We attribute the main source of high-harmonic fluctuations to ionization-induced nonlinear mode mixing during propagation of the drive laser pulse inside the capillary waveguide. △ Less

Submitted 15 July, 2015; originally announced July 2015.

Non-parametric estimation of Fisher information from real data

Authors: Omri Har Shemesh, Rick Quax, Borja Miñano, Alfons G. Hoekstra, Peter M. A. Sloot

Abstract: The Fisher Information matrix is a widely used measure for applications ranging from statistical inference, information geometry, experiment design, to the study of criticality in biological systems. Yet there is no commonly accepted non-parametric algorithm to estimate it from real data. In this rapid communication we show how to accurately estimate the Fisher information in a nonparametric way.… ▽ More The Fisher Information matrix is a widely used measure for applications ranging from statistical inference, information geometry, experiment design, to the study of criticality in biological systems. Yet there is no commonly accepted non-parametric algorithm to estimate it from real data. In this rapid communication we show how to accurately estimate the Fisher information in a nonparametric way. We also develop a numerical procedure to minimize the errors by choosing the interval of the finite difference scheme necessary to compute the derivatives in the definition of the Fisher information. Our method uses the recently published "Density Estimation using Field Theory" algorithm to compute the probability density functions for continuous densities. We use the Fisher information of the normal distribution to validate our method and as an example we compute the temperature component of the Fisher Information Matrix in the two dimensional Ising model and show that it obeys the expected relation to the heat capacity and therefore peaks at the phase transition at the correct critical temperature. △ Less

Submitted 7 July, 2015; v1 submitted 3 July, 2015; originally announced July 2015.

Comments: 6 pages, 5 figures

Journal ref: Phys. Rev. E 93, 023301 (2016)

Topological characterization of S[B] systems: From data to models of complexity

Authors: Emanuela Merelli, Matteo Rucco, Peter Sloot, Luca Tesei

Abstract: In this paper we propose a methodology for deriving a model of a complex system by exploiting the information extracted from Topological Data Analysis. Central to our approach is the S[B] paradigm in which a complex system is represented by a two-level model. One level, the structural S one, is derived using the newly introduced quantitative concept of Persistent Entropy. The other level, the beha… ▽ More In this paper we propose a methodology for deriving a model of a complex system by exploiting the information extracted from Topological Data Analysis. Central to our approach is the S[B] paradigm in which a complex system is represented by a two-level model. One level, the structural S one, is derived using the newly introduced quantitative concept of Persistent Entropy. The other level, the behavioral B one, is characterized by a network of interacting computational agents described by a Higher Dimensional Automaton. The methodology yields also a representation of the evolution of the derived two-level model as a Persistent Entropy Automaton. The presented methodology is applied to a real case study, the Idiotypic Network of the mammal immune system. △ Less

Submitted 25 May, 2015; v1 submitted 21 May, 2015; originally announced May 2015.

Comments: 26 pages, 10 figures

High confinement, high yield Si3N4 waveguides for nonlinear optical application

Authors: Jörn P. Epping, Marcel Hoekman, Richard Mateman, Arne Leinse, René G. Heideman, Albert van Rees, Peter J. M. van der Slot, Chris J. Lee, Klaus-J. Boller

Abstract: In this paper we present a novel fabrication technique for silicon nitride (Si3N4) waveguides with a thickness of up to 900 nm, which are suitable for nonlinear optical applications. The fabrication method is based on etching trenches in thermally oxidized silicon and filling the trenches with Si3N4. Using this technique no stress-induced cracks in the Si3N4 layer were observed resulting in a high… ▽ More In this paper we present a novel fabrication technique for silicon nitride (Si3N4) waveguides with a thickness of up to 900 nm, which are suitable for nonlinear optical applications. The fabrication method is based on etching trenches in thermally oxidized silicon and filling the trenches with Si3N4. Using this technique no stress-induced cracks in the Si3N4 layer were observed resulting in a high yield of devices on the wafer. The propagation losses of the obtained waveguides were measured to be as low as 0.4 dB/cm at a wavelength of around 1550 nm. △ Less

Submitted 13 January, 2015; v1 submitted 31 October, 2014; originally announced October 2014.

Comments: 10 pages, 4 figures

Journal ref: Optics Express, Vol. 23, Issue 2, pp. 642-648 (2015)

Slope Instability of the Earthen Levee in Boston, UK: Numerical Simulation and Sensor Data Analysis

Authors: N. B. Melnikova, D. Jordan, V. V. Krzhizhanovskaya, P. M. A. Sloot

Abstract: The paper presents a slope stability analysis for a heterogeneous earthen levee in Boston, UK, which is prone to occasional slope failures under tidal loads. Dynamic behavior of the levee under tidal fluctuations was simulated using a finite element model of variably saturated linear elastic perfectly plastic soil. Hydraulic conductivities of the soil strata have been calibrated according to piezo… ▽ More The paper presents a slope stability analysis for a heterogeneous earthen levee in Boston, UK, which is prone to occasional slope failures under tidal loads. Dynamic behavior of the levee under tidal fluctuations was simulated using a finite element model of variably saturated linear elastic perfectly plastic soil. Hydraulic conductivities of the soil strata have been calibrated according to piezometers readings, in order to obtain correct range of hydraulic loads in tidal mode. Finite element simulation was complemented with series of limit equilibrium analyses. Stability analyses have shown that slope failure occurs with the development of a circular slip surface located in the soft clay layer. Both models (FEM and LEM) confirm that the least stable hydraulic condition is the combination of the minimum river levels at low tide with the maximal saturation of soil layers. FEM results indicate that in winter time the levee is almost at its limit state, at the margin of safety (strength reduction factor values are 1.03 and 1.04 for the low-tide and high-tide phases, respectively); these results agree with real-life observations. The stability analyses have been implemented as real-time components integrated into the UrbanFlood early warning system for flood protection. △ Less

Submitted 29 January, 2014; originally announced January 2014.

Quantitative Comparison Between Crowd Models for Evacuation Planning and Evaluation

Authors: Vaisagh Viswanathan, Chong Eu Lee, Michael Harold Lees, Siew Ann Cheong, Peter M. A. Sloot

Abstract: Crowd simulation is rapidly becoming a standard tool for evacuation planning and evaluation. However, the many crowd models in the literature are structurally different, and few have been rigorously calibrated against real-world egress data, especially in emergency situations. In this paper we describe a procedure to quantitatively compare different crowd models or between models and real-world da… ▽ More Crowd simulation is rapidly becoming a standard tool for evacuation planning and evaluation. However, the many crowd models in the literature are structurally different, and few have been rigorously calibrated against real-world egress data, especially in emergency situations. In this paper we describe a procedure to quantitatively compare different crowd models or between models and real-world data. We simulated three models: (1) the lattice gas model, (2) the social force model, and (3) the RVO2 model, and obtained the distributions of six observables: (1) evacuation time, (2) zoned evacuation time, (3) passage density, (4) total distance traveled, (5) inconvenience, and (6) flow rate. We then used the DISTATIS procedure to compute the compromise matrix of statistical distances between the three models. Projecting the three models onto the first two principal components of the compromise matrix, we find the lattice gas and RVO2 models are similar in terms of the evacuation time, passage density, and flow rates, whereas the social force and RVO2 models are similar in terms of the total distance traveled. Most importantly, we find that the zoned evacuation times of the three models to be very different from each other. Thus we propose to use this variable, if it can be measured, as the key test between different models, and also between models and the real world. Finally, we compared the model flow rates against the flow rate of an emergency evacuation during the May 2008 Sichuan earthquake, and found the social force model agrees best with this real data. △ Less

Submitted 10 January, 2014; v1 submitted 1 January, 2014; originally announced January 2014.

Comments: 12 pages, 25 figures, accepted in EPJ B

ACM Class: I.2.11; I.6.4; I.6.5; I.6.6; J.2

Reducing cross-flow vibrations of underflow gates: experiments and numerical studies

Authors: C. D. Erdbrink, V. V. Krzhizhanovskaya, P. M. A. Sloot

Abstract: An experimental study is combined with numerical modelling to investigate new ways to reduce cross-flow vibrations of hydraulic gates with underflow. A rectangular gate section placed in a flume was given freedom to vibrate in the vertical direction. Holes in the gate bottom enabled leakage flow through the gate to enter the area directly under the gate which is known to play a key role in most ex… ▽ More An experimental study is combined with numerical modelling to investigate new ways to reduce cross-flow vibrations of hydraulic gates with underflow. A rectangular gate section placed in a flume was given freedom to vibrate in the vertical direction. Holes in the gate bottom enabled leakage flow through the gate to enter the area directly under the gate which is known to play a key role in most excitation mechanisms. For submerged discharge conditions with small gate openings the vertical dynamic support force was measured in the reduced velocity range 1.5 < Vr < 10.5 for a gate with and without holes. The leakage flow through the holes significantly reduced vibrations. This attenuation was most profound in the high stiffness region at 2 < Vr < 3.5. Two-dimensional numerical simulations were performed with the Finite Element Method to assess local velocities and pressures for both gate types. A moving mesh covering both solid and fluid domain allowed free gate movement and two-way fluid-structure interactions. Modelling assumptions and observed numerical effects are discussed and quantified. The simulated added mass in still water is shown to be close to experimental values. The spring stiffness and mass factor were varied to achieve similar response frequencies at the same dry natural frequencies as in the experiment. Although it was not possible to reproduce the vibrations dominated by impinging leading edge vortices (ILEV) at relatively low Vr, the simulations at high Vr showed strong vibrations with movement-induced excitation (MIE). For the latter case, the simulated response reduction of the ventilated gate agrees with the experimental results. The numerical modelling results suggest that the leakage flow diminishes the whipping effect of fluctuations at the trailing edge associated with the streamwise pressure drop across the gate and the body's vertical oscillatory motion. △ Less

Submitted 30 December, 2013; originally announced December 2013.

Comments: 27 pages, 15 figures, 2 tables

Evolutionary Design of Numerical Methods: Generating Finite Difference and Integration Schemes by Differential Evolution

Authors: C. D. Erdbrink, V. V. Krzhizhanovskaya, P. M. A. Sloot

Abstract: Classical and new numerical schemes are generated using evolutionary computing. Differential Evolution is used to find the coefficients of finite difference approximations of function derivatives, and of single and multi-step integration methods. The coefficients are reverse engineered based on samples from a target function and its derivative used for training. The Runge-Kutta schemes are trained… ▽ More Classical and new numerical schemes are generated using evolutionary computing. Differential Evolution is used to find the coefficients of finite difference approximations of function derivatives, and of single and multi-step integration methods. The coefficients are reverse engineered based on samples from a target function and its derivative used for training. The Runge-Kutta schemes are trained using the order condition equations. An appealing feature of the evolutionary method is the low number of model parameters. The population size, termination criterion and number of training points are determined in a sensitivity analysis. Computational results show good agreement between evolved and analytical coefficients. In particular, a new fifth-order Runge-Kutta scheme is computed which adheres to the order conditions with a sum of absolute errors of order 10^-14. Execution of the evolved schemes proved the intended orders of accuracy. The outcome of this study is valuable for future developments in the design of complex numerical methods that are out of reach by conventional means. △ Less

Submitted 30 December, 2013; originally announced December 2013.

Comments: 19 pages, 7 figures, 10 tables, 4 appendices

Integrated CARS Source based on Seeded Four-wave Mixing in Silicon Nitride

Authors: Jörn P. Epping, Michael Kues, Peter J. M. van der Slot, Chris J. Lee, Carsten Fallnich, Klaus-J. Boller

Abstract: We present a theoretical investigation of an integrated nonlinear light source for coherent anti-Stokes Raman scattering (CARS) based on silicon nitride waveguides. Wavelength tunable and temporally synchronized signal and idler pulses are obtained by using seeded four-wave mixing. We find that the calculated input pump power needed for nonlinear wavelength generation is more than one order of mag… ▽ More We present a theoretical investigation of an integrated nonlinear light source for coherent anti-Stokes Raman scattering (CARS) based on silicon nitride waveguides. Wavelength tunable and temporally synchronized signal and idler pulses are obtained by using seeded four-wave mixing. We find that the calculated input pump power needed for nonlinear wavelength generation is more than one order of magnitude lower than in previously reported approaches based on optical fibers. The tuning range of the wavelength conversion was calculated to be 1418 nm to 1518 nm (idler) and 788 nm to 857 nm (signal), which corresponds to a coverage of vibrational transitions from 2350 cm$^{-1}$ to 2810 cm$^{-1}$. A maximum conversion efficiency of 19.1% at a peak pump power of 300 W was obtained. △ Less

Submitted 9 December, 2013; v1 submitted 8 November, 2013; originally announced November 2013.

Comments: 8 pages

Categorical and Geographical Separation in Science

Authors: Julian Sienkiewicz, Krzysztof Soja, Janusz A. Holyst, Peter M. A. Sloot

Abstract: We perform the analysis of scientific collaboration at the level of universities. The scope of this study is to answer two fundamental questions: (i) can one indicate a category (i.e., a scientific discipline) that has the greatest impact on the rank of the university and (ii) do the best universities collaborate with the best ones only? Using two university ranking lists (ARWU and QS) as well as… ▽ More We perform the analysis of scientific collaboration at the level of universities. The scope of this study is to answer two fundamental questions: (i) can one indicate a category (i.e., a scientific discipline) that has the greatest impact on the rank of the university and (ii) do the best universities collaborate with the best ones only? Using two university ranking lists (ARWU and QS) as well as data from the Science Citation Index we show how the number of publications in certain categories correlates with the university rank. Moreover, using complex networks analysis, we give hints that the scientific collaboration is highly embedded in the physical space and the number of common papers decays with the distance between them. We also show the strength of the ties between universities is proportional to product of their total number of publications. △ Less

Submitted 15 December, 2013; v1 submitted 2 July, 2013; originally announced July 2013.

Comments: 17 pages, 12 figures, 3 tables

Distributed simulation of city inundation by coupled surface and subsurface porous flow for urban flood decision support system

Authors: V. V. Krzhizhanovskaya, N. B. Melnikova, A. M. Chirkin, S. V. Ivanov, A. V. Boukhanovsky, P. M. A. Sloot

Abstract: We present a decision support system for flood early warning and disaster management. It includes the models for data-driven meteorological predictions, for simulation of atmospheric pressure, wind, long sea waves and seiches; a module for optimization of flood barrier gates operation; models for stability assessment of levees and embankments, for simulation of city inundation dynamics and citizen… ▽ More We present a decision support system for flood early warning and disaster management. It includes the models for data-driven meteorological predictions, for simulation of atmospheric pressure, wind, long sea waves and seiches; a module for optimization of flood barrier gates operation; models for stability assessment of levees and embankments, for simulation of city inundation dynamics and citizens evacuation scenarios. The novelty of this paper is a coupled distributed simulation of surface and subsurface flows that can predict inundation of low-lying inland zones far from the submerged waterfront areas, as observed in St. Petersburg city during the floods. All the models are wrapped as software services in the CLAVIRE platform for urgent computing, which provides workflow management and resource orchestration. △ Less

Submitted 1 February, 2013; originally announced February 2013.

Comments: Pre-print submitted to the 2013 International Conference on Computational Science

Journal ref: Procedia Computer Science, Volume 18, 2013, Pages 1046-1056

Inference of the Russian drug community from one of the largest social networks in the Russian Federation

Authors: L. J. Dijkstra, A. V. Yakushev, P. A. C. Duijn, A. V. Boukhanovsky, P. M. A. Sloot

Abstract: The criminal nature of narcotics complicates the direct assessment of a drug community, while having a good understanding of the type of people drawn or currently using drugs is vital for finding effective intervening strategies. Especially for the Russian Federation this is of immediate concern given the dramatic increase it has seen in drug abuse since the fall of the Soviet Union in the early n… ▽ More The criminal nature of narcotics complicates the direct assessment of a drug community, while having a good understanding of the type of people drawn or currently using drugs is vital for finding effective intervening strategies. Especially for the Russian Federation this is of immediate concern given the dramatic increase it has seen in drug abuse since the fall of the Soviet Union in the early nineties. Using unique data from the Russian social network 'LiveJournal' with over 39 million registered users worldwide, we were able for the first time to identify the on-line drug community by context sensitive text mining of the users' blogs using a dictionary of known drug-related official and 'slang' terminology. By comparing the interests of the users that most actively spread information on narcotics over the network with the interests of the individuals outside the on-line drug community, we found that the 'average' drug user in the Russian Federation is generally mostly interested in topics such as Russian rock, non-traditional medicine, UFOs, Buddhism, yoga and the occult. We identify three distinct scale-free sub-networks of users which can be uniquely classified as being either 'infectious', 'susceptible' or 'immune'. △ Less

Submitted 13 May, 2013; v1 submitted 20 November, 2012; originally announced November 2012.

Comments: 12 pages, 11 figures