On-line simulation of building energy processes: need and research requirements
Pages 3008 - 3017
Abstract
Most building energy simulation software offers significant building energy performance capabilities; however, its use is limited to design phase only. There is significant benefit to have these energy simulation models available during operation phase for detection and diagnostics. Since simulation models and real building states are not coupled, the models are initialized in an empty state or run through a warm-up period (i.e., off-line simulation). This paper develops the need and research requirements for on-line simulation of building energy processes where current state variables obtained from sensors and meters in buildings are used to initialize the model. Based on the simulation results, a new corrective decision is made and implemented in the real process. This paper argues that on-line simulation can provide decision makers with reliable energy models to test different technical and behavioral interventions, and improve predictions of building performance, compared to the results obtained with existing off-line models.
References
[1]
Abraham, M. and Nguyen, N. (2004) "Green engineering: Defining the Principles." Environmental Progress, 22(4), 233--236.
[2]
Abrahamse, W., Steg, L., Vlek, C., and Rothengatter, T. (2005). "A review of intervention studies aimed at household energy conservation." Journal of Environmental Psychology, 25(3), 273--291.
[3]
Anderson, K., Lee, S. and Menassa, C. (2013). "Agent-based Model of Impact of Social Networks on Change in Building Occupant Behavior Energy Use." Journal of Computing in Civil Engineering -- Special Issue on Computational Approaches to Understand and Reduce Energy Consumption in the Built Environment, ASCE -- Tentatively accepted.
[4]
ASHRAE, (2007b). Guideline 14: Measurement of Energy and Demand Savings (2007).
[5]
Azar, E., and Menassa, C. C. (2012). "Agent-Based Modeling of Occupants' Impact on Energy Use in Commercial Buildings." Journal of Computing in Civil Engineering, ASCE, 26(4), 506.
[6]
Banks, J., J. S. Carson, B. L. Nelson, and D. M. Nicol. 2000. Discrete-Event System Simulation. 3rd ed. Upper Saddle River, New Jersey: Prentice-Hall, Inc.
[7]
Brooks, C., Lee, E. A., Liu, X., Neuendorffer, S., Zhao, Y. and Zheng, H. (2007). "Ptolemy II -- heterogeneous concurrent modeling and design in Java." Technical report No. UCB/EECS-2007-7, Berkeley, CA: University of California at Berkeley.
[8]
Capehart, B., Turner, W., Kennedy, W. (2003). Guide to energy management.4th ed. The Fairmont Press, Inc., Lilburn, Georgia.
[9]
Cheng, R. C. H. 1994. "Selecting Input Models." In Proceedings of the 1994 Winter Simulation Conference, Edited by J. D. Tew, S. Manivannan, D. A. Sadowski, and A. F. Seila, 184--191. Piscataway, New Jersey: Institute of Electrical and Electronics Engineers, Inc.
[10]
Dell'lsola, A. J. and Kirk,S. J.(2003). "Life Cycle Costing of Facilities". Reed Construction Data, Kingston, MA.
[11]
Doukas, H., Nychtis, C. and Psarras, J. (2009). "Assessing energy saving measures in buildings through an intelligent decision support model." Building and Environment, 44(2009), 290--298.
[12]
EIA (2012). "U.S. Energy Information Administration Glossary." Energy Information Administration. Available at: http://www.eia.gov/tools/glossary/index.cfm, last accessed September 2012.
[13]
EnergyPlus (2009a). "Input/Output Reference: The Encyclopedic Reference to EnergyPlus Input and Output". The Board of Trustees of the University of Illinois and the Regents of the University of California through the Ernest Orlando Lawrence Berkeley National Laboratory. Available at: http://apps1.eere.energy.gov/buildings/energyplus/pdfs/inputoutputreference.pdf, last accessed January 21, 2010.
[14]
eQuest (2009). "Introductory Tutorial, version 3.63". http://doe2.com/download/equest/eQ-v3-63_Introductory-Tutorial.pdf, last accessed July 1, 2011.
[15]
Goldman, C., Reid, M., Levy R. and Silverstein, A. (2010). "Coordination of Energy Efficiency and Demand Response." Environmental Energy Technologies Division, Ernest Orlando Lawrence Berkeley National Laboratory, LBNL-3044E.
[16]
Herrmann, R. K. (2005). "Building Automation and LEED Credits." ASHRAE Journal, 47 (9), 10--17.
[17]
Haberl, J. and Bou-Saada, T. (1998). "Procedures for calibrating hourly simulation models to measured building energy and environmental data." Journal of solar energy engineering. 120 (1998) 193--205.
[18]
Jiang, Z., Xia, J. and Jiang, Y. (2009). "An information sharing building automation system." Intelligent Buildings International, Earthscan, 1 (2009), 195--208.
[19]
Kaplan, M., J. Mcferran, J. Jansen, and R. Pratt. "Reconciliation of a DOE2.1c model with monitored end-use data from a small office building" ASHRAE Transactions 96(1), 1992.
[20]
Katipamula, S. and Brambley, M. R. (2005a). "Methods for Fault Detection, Diagnostics, and Prognostics for Building Systems-A Review, Part I." International Journal of HVAC&R Research, 11(1), 3--25.
[21]
Katipamula, S. and Brambley, M. R. (2005b). "Methods for Fault Detection, Diagnostics, and Prognostics for Building Systems-A Review, Part II." International Journal of HVAC&R Research, 11(2), 169--187.
[22]
Kim, H., and Anderson, K. (2012). "Energy Modeling System using Building Information Modeling (BIM) Open Standards". Journal of Computing in Civil Engineering, in press. Available at: http://ascelibrary.org/doi/pdf/10.1061/%28ASCE%29CP.1943-5487.0000215, last accessed October 19, 2012.
[23]
Meier, A., Aragon, C., Hurwitz, B., Peffer, T. and Pritoni, M. (2010). "How People Actually use Thermostats." Washington, D.C.: American Council for an Energy-Efficient Economy.
[24]
Lee, S. U., Painter, F. L. and Claridge, D. E. (2007). "Whole-building commercial HVAC system simulation for use in energy consumption fault detection." ASHRAE Transactions, 113(2), 52--61.
[25]
Lowry, G., (2002). "Factors affecting the success of building management system installations." Building Services Engineering Research & Technology, 23(1), 57--66.
[26]
Menassa, C., Kamat, V., Lee, S., Azar, A., Feng, C. and Anderson, K. (2013a). "A Conceptual Framework to Optimize Building Energy Consumption by Coupling Distributed Energy Simulation and Occupancy Models." Journal of Computing in Civil Engineering --Special Issue on Computational Approaches to Understand and Reduce Energy Consumption in the Built Environment, ASCE -- Tentatively accepted.
[27]
Menassa, C., Taylor, N., and Nelson, J. (2013b). "Optimizing Hybrid Ventilation in Public Spaces of Complex Buildings -- A Case Study of the Wisconsin Institutes for Discovery." Building and Environment, ELSEVIER Volume 61 (2013), 57--68.
[28]
Menassa, C. Taylor, N., and Nelson, J. (2013c). "A Framework for Automated Control and Commissioning of Hybrid Ventilation Systems in Complex Buildings." Automation in Construction, ELSEVIER. Volume 30 (2013), 94--103.
[29]
Menassa, C., Mangasarian, S., El Asmar, M. And Kirar, C. (2012). "Energy Consumption Evaluation of United States Navy LEED Certified Buildings." Journal of Performance of Constructed Facilities, American Society of Civil Engineers, 26 (1), 46--53.
[30]
Mirdamadi, S., F. Fontanili and L. Dupont (2007). "Discrete event simulation-based real-time shop floor control", Proc. 21st Eur. Conf. Modelling and Simulation (ECMS 2007), pp.235--240.
[31]
Pang, X., Wetter, M., Bhattacharya, P. and Haves, P. (2012). "A framework for simulation-based real-time whole building performance assessment." Building and Environment, 54 (2012) 100--108.
[32]
Peschiera, G. and Taylor, J. (2012). "The Impact of Peer Network Position on Electricity Consumption in Building Occupant Networks Utilizing Energy Feedback Systems," Energy and Buildings, 49 (June 2012), 584--590.
[33]
Peschiera, G., Taylor, J., and Siegel, J. (2010). "Response-Relapse Patterns of Building Occupant Electricity Consumption Following Exposure to Personal, Contextualized and Occupant Peer Network Utilization Data," Energy and Buildings, 42(8): 1329--1336.
[34]
Pratt, R. G., "Errors in audit predictions of commercial lighting and equipment loads and their impacts on heating and cooling estimates", ASHRAE Transactions 90-11-2, 1990.
[35]
Rao, Y., He, F., Shao, X., Zhang, C. (2008). "On-line simulation for shop floor control in manufacturing execution system", In: Xiong, C.-H., Liu, H., Huang, Y., Xiong, Y. L. (eds.) ICIRA 2008. LNCS (LNAI), vol. 5315, pp. 141--150. Springer, Heidelberg.
[36]
Samuelson, H. W., Lantz, A. and Reinhart, C. (2011). "Identifying Non-Technical Barriers to Energy Model Sharing and Reuse." Proceedings of Building Simulation 2011, Sydney, Australia. Available at: http://dosen.narotama.ac.id/wp-content/uploads/2012/03/Identifying-non-technical-barriers-to-energy-model-sharing-and-reuse.pdf, last accessed January 2013.
[37]
Schein, J., Bushby, S. T., Castro N. S. and House, J. M. (2006). "A rule-based fault detection method for air handling units." Energy and Buildings, 38 (2006), 1485--1492.
[38]
Soebarto, V. I. and Williamson, T. J. (2001). Multi-criteria Assessment of Building Performance: Theory and Implementation. Building and Environment, Elsevier, 36(6):681--690.
[39]
Široký, J., Oldewurtel, F., Cigler, J. and Prívara, S. (2011). "Experimental analysis of model predictive control for an energy efficient building heating system." Applied Energy, 88 (2011), 3079--3087.
[40]
Staats, H., Harland, P., and Wilke, H. A. M. (2004). "Effecting Durable Change: A Team Approach to Improve Environmental Behavior in the Household." Environment and Behavior, Sage Publications, 36(3), 341--367.
[41]
Staats, H., van Leeuwen, E., and Wit, A. (2000). "A Longitudinal Study of Informational Interventions to Save Energy in an Office Building." Journal of Applied Behavior Analysis, Society for the Experimental Analysis of Behavior, 33(1), 101--104.
[42]
Wetter, M. (2011). "Co-simulation of building energy and control systems with the Building Controls Virtual Test Bed." Journal of Building Performance Simulation, 4(3), 185--203.
[43]
Wu, S. and Sun, S. W. (2010). "Multilevel fault detection and diagnosis on office building HVAC systems." 2010 ACEEE Summer Study on Energy Efficiency in Buildings, American Council for energy Efficient Economy, 3: 362--373.
[44]
United Nations Environment Programme. (2007). "Buildings Can Play Key Role in Combating Climate Change." SBCI-Sustainable Construction and Building Initiative, Available at http://www.unep.org/Documents.Multilingual/Default.Print.asp, last accessed January 2013.
[45]
US Environmental Protection Agency -- (EPA) (2012). "Guidelines for Energy Management." http://www.energystar.gov/index.cfm?c=guidelines.download_guidelines, last accessed April 2012.
[46]
US Environmental Protection Agency (EPA). (2010). ENERGY STAR ® and Other Climate Protection Partnerships - 2010 Annual Report 2010 ANNUAL REPORT.
[47]
US Department of Energy (DOE) (2002). International Performance Measurement & Verification Protocol: Concepts and Options for Determining Energy and Water Savings Vol. I (2002).
[48]
US Department of Energy (DOE) (2008). M&V Guidelines: Measurement and Verification for Federal Projects (2008).
[49]
Yoon, J., Lee, E. J. and Claridge, D. (2003). "Calibration procedure for energy performance simulation of a commercial building." Journal of solar energy engineering. 125 (2003), 251--257.
[50]
Yudelson, J. (2010). "Greening Existing Buildings." McGraw Hill - A Green Source Book, New York.
Recommendations
Distributed building energy simulation with the HLA
SummerSim '19: Proceedings of the 2019 Summer Simulation ConferenceThe primary aim of this work is to demonstrate the feasibility of applying the High Level Architecture (HLA) framework to the distributed execution of physical urban building energy simulations that are too large to be supported within the resource ...
Exploring the validity of occupant behavior model for improving office building energy simulation
WSC '18: Proceedings of the 2018 Winter Simulation ConferenceBuilding energy use is significantly influenced by building occupants or users. The integration of a robust occupant behavior model that captures energy-related behaviors and a building energy model will have the potential to improve energy simulation ...
Analysis of the differences in energy simulation results between building information modeling (BIM)-based simulation method and the detailed simulation method
WSC '11: Proceedings of the Winter Simulation ConferenceBuilding Information Modeling (BIM)-based simulation models have been used to automate lengthy building energy modeling processes and it enable fast acquisition of results. Recent improvements of simulation programs have continued to the increase in the ...
Comments
Information & Contributors
Information
Published In
December 2013
4386 pages
ISBN:9781479920778
- General Chair:
- Raymond R. Hill,
- Program Chair:
- Michael E. Kuhl
Sponsors
- IIE: Institute of Industrial Engineers
- INFORMS-SIM: Institute for Operations Research and the Management Sciences: Simulation Society
- ASA: American Statistical Association
- SIGSIM: ACM Special Interest Group on Simulation and Modeling
- SCS: Society for Modeling and Simulation International
- ASIM: Arbeitsgemeinschaft Simulation
- IEEE/SMCS: Institute of Electrical and Electronics Engineers/Systems, Man, and Cybernetics Society
- NIST: National Institute of Standards & Technology
Publisher
IEEE Press
Publication History
Published: 08 December 2013
Check for updates
Qualifiers
- Research-article
Conference
WSC '13
Sponsor:
- IIE
- INFORMS-SIM
- ASA
- SIGSIM
- SCS
- ASIM
- IEEE/SMCS
- NIST
Acceptance Rates
Overall Acceptance Rate 3,413 of 5,075 submissions, 67%
Contributors
Other Metrics
Bibliometrics & Citations
Bibliometrics
Article Metrics
- 0Total Citations
- 68Total Downloads
- Downloads (Last 12 months)0
- Downloads (Last 6 weeks)0
Reflects downloads up to 10 Nov 2024
Other Metrics
Citations
View Options
Get Access
Login options
Check if you have access through your login credentials or your institution to get full access on this article.
Sign in