Abstract
Organicâinorganic perovskite solar cells have attracted tremendous attention because of their remarkably high power conversion efficiencies. To further improve device performance, it is imperative to obtain fundamental understandings on the photo-response and long-term stability down to the microscopic level. Here, we report the quantitative nanoscale photoconductivity imaging on two methylammonium lead triiodide thin films with different efficiencies by light-stimulated microwave impedance microscopy. The microwave signals are largely uniform across grains and grain boundaries, suggesting that microstructures do not lead to strong spatial variations of the intrinsic photo-response. In contrast, the measured photoconductivity and lifetime are strongly affected by bulk properties such as the sample crystallinity. As visualized by the spatial evolution of local photoconductivity, the degradation process begins with the disintegration of grains rather than nucleation and propagation from visible boundaries between grains. Our findings provide insights to improve the electro-optical properties of perovskite thin films towards large-scale commercialization.
Similar content being viewed by others
Introduction
The worldwide surge of research interest in organicâinorganic trihalide perovskites, e.g., methylammonium lead triiodide (CH3NH3PbI3 or MAPbI3), has led to a phenomenal increase of the power conversion efficiency (PCE) of perovskite solar cells (PSCs) from 3.8 to 22% in the past few years1,2,3,4,5,6. These hybrid organicâinorganic thin films are polycrystalline in nature and compatible with low-cost solution or vapor-based processes7,8,9. Yet their performance rivals many single-crystalline semiconductor solar cells10 owing to a number of intriguing optical and electrical properties that are ideal for energy harvesting and charge transport, such as high absorption coefficient across the visible spectrum11, high carrier mobility11,12, and long carrier recombination lifetime13,14. The unprecedented progress of PSC efficiency was often attributed to the unique defect structures in the bulk and the benign grain boundaries during the early stage of PSC development15,16.
As the PSC efficiency continues to increase, recent efforts on increasing grain sizes and/or passivating grain boundaries (GBs) have casted doubts on the general belief in the unique defect tolerance in perovskites. Several groups including us have found that, when the grain size is increased from a few hundred nanometers to the micrometer level, the device performance is often significantly improved together with elongated charge-carrier lifetimes17,18,19,20,21. At first sight, these studies imply that GBs in polycrystalline perovskite thin films may not be as benign as early studies had suggested. A recent theoretical study pointed out that GBs may even be the major recombination sites in the standard iodide based perovskites22, which seems to be consistent with the recent experimental efforts described above. It is worth noting that regardless the chemical/physical natures of the defects, there are three primary spatial locations of defects related to perovskite thin films, i.e., film surface, bulk of the grain, and boundary between neighboring grains. Thus, in addition to possible changes of GB properties, the various new growth controls for increasing grain sizes could also affect the surface and bulk properties of perovskite grains, e.g., enhanced crystallinity, reduced defect density at the surface and in the bulk, and reduced structural defects associated with pinhole formation. Thus, it is important to scrutinize and isolate the impact of these different microscopic factors on electro-optical properties of polycrystalline perovskite thin films. Moreover, as material stability continues to be the key challenge faced by the PSC community8, an immediate question is whether the GB and/or the surface of perovskite films are the weakest points where the degradation would start first. To this end, understanding the degradation mechanism at the microscopic level is also imperative for fabricating robust and reliable devices that meet the stringent requirements of commercialization23,24,25,26,27,28,29. In contrast to conventional macroscopic device characterizations, it is expected that spatially resolved studies on the chemical, electrical, and optical properties of the PSC thin films will provide crucial information for advancing the basic science and developing commercial products based on these fascinating materials.
While a number of scanning probe techniques30,31,32,33,34,35,36,37,38 have been used to interrogate properties of the PSC, local measurements of the intrinsic photoconductivity, rather than the extrinsic photocurrent across the Schottky-like tipâsample junction, have not been reported to investigate the role of various microstructures on the films. In addition, due to the poor air stability of the organicâinorganic trihalide compound, experiments on samples with a surface encapsulation layer are desirable to obtain reliable results. A non-contact method capable of mapping out the nanoscale photoconductivity on encapsulated films is thus particularly important for the PSC research. In this work, we report the first quantitative microwave impedance imaging with light stimulation on two MAPbI3 thin films with different PCEs capped by a polymethyl methacrylate (PMMA) protection layer. The photo-response is spatially uniform across grains and grains boundaries, whereas the difference of carrier mobility and lifetime between these two films is attributed to the difference of sample crystallinity. Both the surface topography and local photoconductivity have been monitored over an extended period of time, which sheds new light on the intricate degradation process of the PSC devices.
Results
Microwave photoconductivity imaging on MAPbI3
Our experiments are performed on a unique microwave impedance microscopy (MIM)39,40 setup with a focused laser beam illuminating from below the sample stage, as illustrated in Fig. 1a. The bottom illumination scheme avoids light being shallowed by the body of the cantilever probe41 and ensures an accurate calibration of the areal power intensity on the sample. Taking advantage of the near-field interaction, we are able to obtain a spatial resolution with deeply subwavelength lateral dimensions, i.e., on the order of the tip diameter (around 100ânm or 1/30,000λ, where λ is the wavelength of the 1âGHz microwave)40. Here the 1âGHz signal is delivered to the shielded cantilever tip42 and the reflected microwave is amplified and demodulated to form MIM-Im and MIM-Re signals, which are proportional to the imaginary and real parts of the tipâsample admittance39. Unlike the conductive AFM32,33,34,35, a direct contact between the MIM tip and the perovskite thin films is not required due to the efficient capacitive coupling at GHz frequencies, overcoming the challenges of interrogating nanoscale electrical properties on samples with an insulating capping layer. The contrast mechanism of the MIM is similar to that of the time-resolved microwave conductivity (TRMC) experiment11,12,43,44,45,46, a non-contact technique widely exploited to study the dynamics of photo-generated carriers, except that the time resolution in TRMC under pulsed excitation is traded for spatial resolution in MIM under continuous illumination.
The 100-nm thick MAPbI3 thin films are prepared by an excess organic salt based solventâsolvent extraction method21. The precursor solution (30âwt%) is spin-coated on glass substrates at 6000ârpm for 25âs to form a wet precursor film, which is then transferred into a stirred ether bath for 1âmin, followed by thermal annealing at 150â°C for 15âmin with a petri dish covered. Solar cell devices made from the same material but with thicker film (350ânm) have demonstrated a PCE of 18% (reverse scan) under the standard Air Mass (AM) 1.5 illumination (Supplementary Fig. 1). As a comparison, 100-nm thick MAPbI3 films with smaller grain size was deposited using the same process except with stoichiometry precursor and annealing at 100â°C for 10âmin. Devices with small grain size and thicker (350ânm) perovskite film possess a PCE of 15% (reverse scan) (Supplementary Fig. 1). To further verify the cell performance, we also measure the stabilized power output (SPO) near the maximum power point for these two perovskite cells (Supplementary Fig. 2). The SPOs are about 17.69% and 13.1% for cells based on large and small grains, respectively. In addition, energy-dispersive X-ray spectroscopy (EDS) measurement (Supplementary Fig. 3) also suggests that there is no clear correlation between the Pb and I distribution and the grain morphology (e.g., grain vs. grain boundary) in both samples. Pb and I stay roughly constant across multiple grains within experimental noise and the ratio of I/Pb is essentially the same for both samples. Consistent with previous studies23,24,25, uncapped MAPbI3 thin films degrade within several hours under the ambient light and humidity conditions, as shown in Supplementary Fig. 4. To prevent such rapid degradation, we have capped the sample surface with a thin (30ânm thick) layer of spin-coated PMMA47 in the following experiments. As shown in the schematic in Fig. 1a, part of the PMMA/MAPbI3 films is scratched away to expose the glass substrate as the reference region for the MIM imaging.
Before discussing our main results, it is instructive to review the contrast mechanism and response function of the MIM technique. Figure 1b shows the finite-element analysis (FEA) results based on the actual tip/sample geometry and material properties. Details of the FEA process are described in Supplementary Fig. 5. As the conductivity Ï of MAPbI3 increases, the microwave electrical fields are gradually pushed away from this layer due to the screening effect from free carriers. As a result, the MIM-Im signal, which is proportional to the tipâsample capacitance, starts to rise as Ïâ>â10â1âSâmâ1, increases monotonically as a function of Ï, and saturates for Ïâ>â103âSâmâ1. On the other hand, the MIM-Re signal (proportional to the electrical loss at 1âGHz), peaks around Ïâ=â101âSâmâ1 and decreases for both higher and lower conductivities. Note that while the simulation is performed for a uniform MAPbI3 layer, the span of the quasi-static electric field, which determines the lateral resolution and vertical probing depth, is set by the tip diameter. The MIM thus maps out the local variation of conductivity in the mesoscopic length scale of around 100ânm.
Figure 2a, b displays the AFM and MIM images of the samples with 18% and 15% PCEs, respectively. The large difference in grain sizes between these two films is evident from the topographic data. Without the illumination, there is little MIM contrast between the highly resistive perovskite film and the glass substrate (Supplementary Fig. 6). When illuminated by an above-gap continuous-wave 532ânm laser with a power intensity P of 100âmWâcmâ2 (on the order of 1âSun at AM 1.5), the 18% PCE sample exhibits clear photo-induced MIM signals, while the effect is much weaker on the 15% PCE sample. As a control experiment, we have also performed the MIM imaging when the 18% PCE sample is illuminated by a below-gap 980-nm laser with the same power density of 100âmWâcmâ2, as shown in Supplementary Fig. 6. The absence of photo-induced MIM signals with below-gap illumination further confirms the photoconductivity in the MAPbI3 films.
Quantitative analysis of photo-response
The intrinsic photoconductivity images in Fig. 2 contain much information on the photon-to-electron conversion process, which is at the heart of solar cell devices. For the quantitative analysis, we first focus on the power dependence of MIM response on the 18% PCE sample. Figure 3a shows the average MIM signals over an area of 3.5âÃâ3.5âμm as a function of the 532ânm-laser intensity (raw data displayed in Supplementary Fig. 7a). The MIM-Im signals increase monotonically with the laser power and saturate for both Pâ<â10âmWâcmâ2 and Pâ>â104âmWâcmâ2. The MIM-Re signals, on the other hand, reach a peak at P around 103âmWâcmâ2 and decrease on both sides. The close resemblance between Figs. 1b and 3a allows us to quantitatively extract Ï from the measured data. Since the film thickness is comparable to the tip diameter, the MIM is measuring the effective photoconductivity Ï averaged over the vertical direction, which can be derived as follows48 (assuming complete absorption by the film):
As an order-of-magnitude estimate, i.e., taking the incident photon-to-electron conversion efficiency (IPCE, hereafter denoted as η) ηâ=â1, film thickness Hâ=â100ânm, electron and hole lifetime Ï e âÏ h ââ102âns, photon energy hν=2.33âeV, electron and hole mobility μ e âμ hâ ââ102âcm2âVâ1âsâ1, we obtain Ïâââ10âSâmâ1 at Pâ=â100âmWâcmâ2, which is in excellent agreement with the data in Fig. 3c. The corresponding electron (hole) density is n(p)=PÏ e(h)/(H·hν)â3Ã1015âcmâ3, consistent with other investigations49. For laser intensity above 100âmWâcmâ2, the sub-linear power dependence observed in Fig. 3c may result from the saturation of photo-generated carriers50. On the other hand, it is generally believed that trap states in MAPbI3 remain unfilled at around 1âSun and become filled up to 10â100âSun under the steady-state illumination44. It is thus possible that trap states also play a role in the saturation of photoconductivity in Fig. 3c.
We now turn to the comparison between the two MAPbI3 thin films. Following the same procedure, the MIM signals and power-dependent photoconductivity of the 15% PCE sample are (raw data shown in Supplementary Fig. 7b) plotted in Fig. 3b, c, respectively. In the regime relevant to practical solar cell applications (P no greater than 100âmWâcmâ2), the photoconductivity of the 18% PCE sample is five to six times higher than that of the 15% PCE sample. The two films show very similar wavelength-dependent absorptivity and IPCE over the visible spectrum, as seen in Fig. 3d. The time-resolved photoluminescence (TRPL) data in Fig. 3e show that the total electronâhole recombination time is 280âns and 80âns for the 18% and 15% PCE samples, respectively, from which we estimate that the average carrier lifetime differs by a factor of three between the two films. As a result, the average mobility is also improved by a considerable amount (about two times) in the 18% film. Finally, from our X-ray diffraction (XRD) data in Fig. 3f, the substantially better crystallinity of the 18% film is vividly demonstrated by its much stronger MAPbI3 peak than the 15% counterpart. In all, as the average grain size increases from a few hundred nanometers to a few micrometers due to the better growth control, both the electronâhole recombination rate and transport scattering rate are considerably reduced.
Photoconductivity of grain boundaries
To understand the role of GBs, we directly compare the local photoconductivity between grains and GBs in the 18% PCE sample. From the AFM image in Fig. 4a, appreciable inhomogeneity is seen on the polycrystalline MAPbI3 thin film, with grain sizes ranging from sub-micrometer to a few micrometers and GBs appearing as trenches of about 10ânm in depth. In contrast, the corresponding MIM images are relatively uniform over grains with different heights and lateral sizes. In Fig. 4b, we compare the line profiles across a single GB from the AFM and MIM images. Note that the MIM-Im channel is susceptible to the topographic crosstalk, while the MIM-Re signal is less sensitive to the surface roughness. We emphasize that the topographic mixing is not proportional to the AFM data and cannot be removed by simple image processing. The AFM data represent the position of the tip apex when scanning on a surface with certain roughness. The topographic mixing in the MIM-Im data, on the other hand, is mostly due to the stray capacitance from the non-apex part when the tip tracks the sample surface. For quantitative analysis of the GB photoconductivity Ï GB, we perform the 3D FEA simulation (detailed in Supplementary Fig. 8), in which the GB is modeled as a thin slab (10ânm in width w) with a height difference ÎH of 10ânm lower than the grains (10âSâmâ1). Within the experimental uncertainty, a comparison between the MIM data and the FEA shows that Ï GB is within a factor of two from Ï G. As a control experiment, we have also conducted the MIM measurement on a thicker (300ânm) film of the 18% PCE sample and observed the same results (Supplementary Fig. 9), which indicates that the MIM signals are not dominated by the possible surface recombination in the 100ânm film. The result of nearly uniform photoconductivity is striking since GBs contain a large amount of dangling bonds, which usually lead to trap states detrimental to carrier generation and charge transport in conventional solar cell materials7. For halide perovskites, the role of GBs has been under debate over the years. While some theoretical studies showed that GBs only create shallow in-gap states due to the high ionicity and strong PbâI anti-bonding15,16, others indicated that GBs are the major recombination centers and should be passivated22. Our measurements provide direct experimental evidence that, at least for encapsulated thin films with micrometer-sized grains, GBs are relatively benign to carrier generation and transport. Perovskite films with better crystallinity, on the other hand, should be the direction to further improve the efficiency of PSCs.
Spatial evolution of the degradation process
The air stability of the perovskite films, which is arguably the most serious bottleneck towards commercial applications23,24,25,26,27,28,29, has also been studied by the MIM. Figure 5a shows selected AFM and MIM images of a PMMA-coated MAPbI3 film over 1 week under the ambient condition with a relative humidity of 35% at 23â°C (complete set of data included in Supplementary Fig. 10). Little change in the photoconductivity is observed on the first day or two, suggesting that the PMMA capping layer was initially effective in preventing the film degradation. Starting from Day 3, however, appreciable reduction of the photo-response is seen in certain regions of the film. Interestingly, the degradation does not emerge from GBs but is associated with the disintegration of large grains, which substantially reduces the photoconductivity in the surrounding regions. The degraded areas continue to grow during the subsequent days and the photoconductivity completely diminishes after Day 6. We note that recent transmission electron microscopy (TEM) studies have revealed the existence of twin boundaries that are not seen in traditional SEM or AFM images51. Our results are thus only valid for the GBs with clear topographic features. As a control experiment, we also continuously illuminate another sample for 9âh (same as the total imaging time in the aging experiment above) and observe no change in both topographic and photoconductivity maps (Supplementary Fig. 11). The illumination by itself, therefore, is not sufficient to cause the drastic suppression of photoconductivity in Fig. 5a.
To gain further insight on the aging process, we have carried out structural and optical characterizations on films prepared by the same method and exposed to the same conditions. As seen in the XRD results in Fig. 5b, the characteristic PbI2 peak at 2θâ=â12.66° appears on Day 1 and becomes significant on Day 3. The spectrum on Day 6 is dominated by the strong PbI2 peak, indicative of the nearly complete decomposition of MAPbI3 after 1 week. Note that the emergence of PbI2 reduces the local photoconductivity because its absorption edge at 525ânm52 is at higher energy than our 532ânm laser. The TRPL data plotted in Fig. 5c also demonstrate the same trend. While little change is observed after one day, the absolute PL intensity drops substantially on Day 3 and the TRPL decay rate increases rapidly on Day 6. Interestingly, the TRPL decay rates are similar for the first three days, suggesting that the carrier lifetime remains large in the unaffected regions. Combining the microscopic and macroscopic results, we conclude that the deterioration of the encapsulated film is initiated and accelerated by the water molecules slowly diffused through the PMMA layer, which drive the decomposition of large MAPbI3 grains into PbI2 in the solid phase and CH3NH2 and HI in the gas phase23,24,25,26. Again, GBs are not the nucleation centers during the degradation.
Discussion
To summarize, we report the intrinsic photoconductivity mapping of thin-film MAPbI3 with different PCEs under above-gap illuminations. The large photoconductivity of the higher efficiency sample is a direct consequence of the high carrier mobility and long lifetime because of the improved crystallinity. Surprisingly, the GBs exhibit photo-responses comparable to the grains, and they are not the nucleation centers for the degradation process. Our results highlight the unique defect structures responsible for the remarkable performance of PSC devices, and address the significance of crystallinity to further improve their energy conversion efficiency. We also emphasize that the nanoscale photoconductivity imaging by microwave microscopy represents a new methodology in optoelectronic research. With future development to incorporate broadband illumination, variable temperatures, and humidity-controlled environment, we expect to obtain further insights on the intriguing photo physics and air sensitivity of the hybrid perovskite materials.
Methods
Preparation of MAPbI3 perovskite thin films
The perovskite films in this work were deposited on top of cover glasses using the stoichiometry and non-stoichiometry solventâsolvent extraction method21. In short, 30âwt% methylammonium iodide (MAI) and lead iodide (PbI2) (MAI/PbI2â=â1/1, MAI/PbI2â=â1.2/1) were dissolved in a mixed solvent of 1-N-methyl-2-pyrrolidinone (NMP) and γ-butylrolactone (GBL) (NMP/GBLâ=â7/3 weight ratio). The cover glass with 80âµl precursor solution was spun at 6000ârpm for 25âs, and immediately dipped into a vigorously stirred diethyl ether bath for 1âmin. The perovskite films rapidly crystallized during the bathing process and were further annealed (stoichiometry precursor: 100â°C for 10âmin; non-stoichiometry precursor: 150â°C for 15âmin) with a petri-dish covered to remove excess organic salt. Within the experimental errors of our characterization tools, these two types of perovskite films show the same MAPbI3 perovskite composition and crystal structure and only differ in grain size and crystallinity21. The encapsulated perovskite films were capped with PMMA (M w about 120,000) film by spin-coating 15âmgâmlâ1 PMMA in chlorobenzene solution at 4000ârpm for 35âs.
Structural and optical characterizations
The absorption spectra were measured by a UV/Vis spectrometer (Cary-6000i). The perovskite structure was characterized by an X-ray diffractometer (Rigaku D/Max 2200) using the Cu Kα radiation. The incident photon-to-electron conversion efficiency (IPCE) experiment was carried out in a solar cell quantum efficiency measurement system (QEX10, PV Measurements). The time-resolved photoluminescence (TRPL) measurements were conducted in a home-built time correlated single photon counting system, where light source is a Fianium Supercontinuum high power broadband fiber laser (SC400-2-PP). The excitation wavelength was 500ânm with a spot area of 300âÃâ300âμm, a power of about 5âμW, and a repetition rate of 0.1âMHz.
Microwave impedance microscopy and finite-element analysis
The MIM in this work is based on a modified ParkAFM XE-100 platform with bottom illumination. The customized shielded cantilever probes40 are commercially available from PrimeNano Inc.
Finite-element analysis is performed using the AC/DC module of commercial software COMSOL4.4. Supplementary Figure 5 shows the FEA simulation result using the tip/sample geometry and material properties39. The upper part of the tip is modeled as a truncated cone with a half-angle of 15° and a diameter of 200ânm at the bottom surface. The radius of curvature of the tip apex (modeled as a truncated sphere), 250ânm in this case, is determined by calibration on standard samples. The relative dielectric constant ε of MAPbI3 is assumed to be 60, consistent with that reported in the literature7. From the AFM data, the thicknesses of the PMMA (εâ=â3, http://webhotel2.tut.fi/projects/caeds/tekstit/plastics/plastics_PMMA.pdf) and MAPbI3 are 30ânm and 100ânm, respectively. Supplementary Figure 5a shows the simulated real and imaginary parts of the tipâsample admittance as a function of the conductivity of the MAPbI3 layer, using the values at Ïâ=â0 as the reference points. The MIM electronics is calibrated in that an admittance contrast of 1ânS corresponds to an output voltage of 3.5âmV. In general, the MIM-Im signal, which is proportional to the tipâsample capacitance, increases monotonically as a function of Ï. The MIM-Re signal, which corresponds to the electrical loss at 1âGHz, peaks at intermediate Ï and decreases for both good conductors and good insulators. The quasi-static potential and displacement field distributions around the tipâsample junction are shown in Supplementary Fig. 5b for three characteristic conductivities at 0.1, 10, and 1000âSâmâ 1, respectively.
The 2D axisymmetric simulation in Supplementary Fig. 5 does not work for the modeling of grain boundaries (GBs) because of the lack of rotational symmetry. To quantitatively understand the experimental data, we have performed 3D simulation and modeled the GB as a thin slab sandwiched between two adjacent grains. The center of the GB is 10ânm (ÎH) lower than the surrounding grains, giving rise to the topographic artifact to the MIM signals described below. The width (w) of the GB, within which the electronic conductivity may differ from Ï G due to dangling bonds and other defects, is assumed to be 10ânm. The simulated MIM signals when the tip locates on top of the GB are plotted in Supplementary Fig. 8a, together with the signals when the tip locates on top of the grains (Ï Gâ=â10âSâmâ 1 under the 100âmWâcmâ 2 illumination). The tipâsample interaction at various Ï GBâs can be visualized by the quasi-static displacement field distribution in Supplementary Fig. 8b. The relative MIM contrast (GBs vs. grains) in our experiment corresponds to the difference between solid and dashed lines in Supplementary Fig. 8a. Note that the MIM-Im contrast is considerably affected by the topographic crosstalk, as the GB signals are always higher than that within the grains for all Ï GBâs. Nevertheless, by comparing the FEA results in Fig. 4c and the experimental data (60âmV contrast in MIM-Im and 10âmV contrast in MIM-Re) in Fig. 4b, it is evident that Ï GB is not substantially smaller than Ï G (within a factor of 2). We therefore conclude that Ï GB is not substantially smaller than Ï G (within a factor of 2). We therefore conclude that GBs are intrinsically benign in MAPbI3 thin films with photoconductivity comparable to that within the grains15.
Data availability
The data that support the findings of this work are available from the corresponding author upon reasonable request.
References
Kojima, A., Teshima, K., Shirai, Y. & Miyasaka, T. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells. J. Am. Chem. Soc. 131, 6050â6051 (2009).
Lee, M. M., Teuscher, J., Miyasaka, T., Murakami, T. N. & Snaith, H. J. Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites. Science 338, 643â647 (2012).
Burschka, J. et al. Sequential deposition as a route to high-performance perovskite-sensitized solar cells. Nature 499, 316â319 (2013).
Liu, M., Johnston, M. B. & Snaith, H. J. Efficient planar heterojunction perovskite solar cells by vapour deposition. Nature 501, 395â398 (2013).
Zhou, H. et al. Interface engineering of highly efficient perovskite solar cells. Science 345, 542â546 (2014).
Nie, W. et al. High-efficiency solution-processed perovskite solar cells with millimeter-scale grains. Science 347, 522â525 (2015).
Green, M. A., Ho-Baillie, A. & Snaith, H. J. The emergence of perovskite solar cells. Nat. Photonics 8, 506â514 (2014).
Berry, J. et al. Hybrid origanic-inorganic perovskites (HOIPs): opportunities and challenges. Adv. Mater. 27, 5102â5112 (2015).
Stranks, S. D. & Snaith, H. J. Metal-halide perovskite for photovoltaic and light-emitting devices. Nat. Nanotechnol. 10, 391â402 (2015).
Lewis, N. S. Research opportunities to advance solar energy utilization. Science 351, 1920 (2016).
Ponseca, C. S. et al. Organometal halide perovskite solar cell materials rationalized: ultrafast charge generation, high and microsecond-long balanced mobilities, and slow recombination. J. Am. Chem. Soc. 136, 5189â5190 (2014).
Oga, H., Saeki, A., Ogomi, Y., Hayase, S. & Seki, S. Improved understanding of the electronic and energetic landscapes of perovskite solar cells: high local charge carrier mobility, reduced recombination, and extremely shallow traps. J. Am. Chem. Soc. 136, 13818â13825 (2014).
Stranks, S. D. et al. Electron-hole diffusion lengths exceeding 1 micrometer in an organometal trihalide perovskite absorber. Science 342, 341â344 (2013).
Shi, D. et al. Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals. Science 347, 519â522 (2015).
Yin, W. J., Shi, T. & Yan, Y. Unique properties of halide perovskites as possible origins of the superior solar cell performance. Adv. Mater. 26, 4653â4658 (2014).
Yin, W. J., Shi, T. & Yan, Y. Unusual defect physics in CH3NH3PbI3 perovskite solar cell absorber. Appl. Phys. Lett. 104, 063903 (2014).
Xiao, Z. G. et al. Solvent annealing of perovskite-induced crystal growth for photovoltaic-device efficiency enhancement. Adv. Mater. 26, 6503â6509 (2014).
Yang, B. et al. Perovskite solar cells with near 100% internal quantum efficiency based on large single crystalline grains and vertical bulk heterojunctions. J. Am. Chem. Soc. 137, 9210â9213 (2015).
De Marco, N. et al. Guanidinium: a route to enhanced carrier lifetime and open-circuit voltage in hybrid perovskite solar cells. Nano Lett. 16, 1009â1016 (2016).
Zhang, W. et al. Enhanced optoelectronic quality of perovskite thin films with hypophosphorous acid for planar heterojunction solar cells. Nat. Commun. 6, 10030 (2015).
Yang, M., Zhou, Y., Zeng, Y., Jiang, C. S. & Padture, N. P. et al Square-centimeter solution-processed planar CH3NH3PbI3 perovskite solar cells with efficiency exceeding 15%. Adv. Mater. 27, 6363â6370 (2015).
Long, R., Liu, J. & Prezhdo, O. V. Unravelling the effects of grain boundary and chemical doping on electronâhole recombination in CH3NH3PbI3 Perovskite by Time-Domain Atomistic Simulation. J. Am. Chem. Soc. 138, 3884â3890 (2016).
Niu, G. et al. Study on the stability of CH3NH3PbI3 films and the effect of post-modification by aluminum oxide in all-solid-state hybrid solar cells. J. Mater. Chem. A 2, 705â710 (2014).
Leijtens, T. et al. Stability of metal halide perovskite solar cells. Adv. Energy Mater. 5, 1500963 (2015).
Han, Y. et al. Degradation observations of encapsulated planar CH3NH3PbI3 perovskite solar cells at high temperatures and humidity. J. Mater. Chem. A 3, 8139â8147 (2015).
Niu, G., Guo, X. & Wang, L. Review of recent progress in chemical stability of perovskite solar cells. J. Mater. Chem. A 3, 8970â8980 (2014).
Berhe, T. A. et al. Organometal halide perovskite solar cells: degradation and stability. Energy Environ. Sci. 9, 323â356 (2016).
Yang, J., Siempelkamp, B. D., Liu, D. & Kelly, T. L. Investigation of CH3NH3PbI3 degradation rates and mechanisms in controlled humidity environments using in situ techniques. ACS Nano 9, 1955â1963 (2015).
Divitini, G. et al. In situ observation of heat-induced degradation of perovskite solar cells. Nat. Energy 1, 15012 (2016).
Jiang, C. et al. Carrier separation and transport in perovskite solar cells studied by nanometre-scale profiling of electrical potential. Nat. Commun. 6, 8397 (2015).
Xiao, Z. et al. Giant switchable photovoltaic effect in organometal trihalide perovskite devices. Nat. Mater. 14, 193â198 (2014).
Zhao, Z., Chen, X., Wu, H., Wu, X. & Cao, G. Probing the photovoltage and photocurrent in perovskite solar cells with nanoscale resolution. Adv. Funct. Mater. 26, 3048â3058 (2016).
Yun, J. S. et al. Benefit of grain boundaries in organicâinorganic halide planar perovskite solar cells. J. Phys. Chem. Lett. 6, 875â880 (2015).
Kutes, Y. et al. Mapping the photoresponse of CH3NH3PbI3 hybrid perovskite thin films at the nanoscale. Nano Lett. 16, 3434â3441 (2016).
Son, D. et al. Self-formed grain boundary healing layer for highly efficient CH3NH3PbI3 perovskite solar cells. Nat. Energy 1, 16081 (2016).
Kutes, Y. et al. Direct observation of ferroelectric domains in solution-processed CH3NH3PbI3 perovskite thin films. J. Phys. Chem. Lett. 5, 3335â3339 (2014).
Fan, Z. et al. Ferroelectricity of CH3NH3PbI3 perovskite. J. Phys. Chem. Lett. 6, 1155â1161 (2015).
deQuilettes, D. W. et al. Impact of microstructure on local carrier lifetime in perovskite solar cells. Science 348, 683â686 (2015).
Lai, K., Kundhikanjana, W., Kelly, M. & Shen, Z. X. Modeling and characterization of a cantilever-based near-field scanning microwave impedance microscope. Rev. Sci. Instrum. 79, 063703 (2008).
Lai, K., Kundhikanjana, W., Kelly, M. A. & Shen, Z. X. Nanoscale microwave microscopy using shielded cantilever probes. Appl. Nanosci. 1, 13â18 (2011).
Tuteja, M., Koirala, P., Maclaren, S., Collins, R. & Rockett, A. Direct observation of electrical properties of grain boundaries in sputter-deposited CdTe using scan-probe microwave reflectivity based capacitance measurements. Appl. Phys. Lett. 107, 142106 (2015).
Yang, Y. et al. Batch-fabricated cantilever probes with electrical shielding for nanoscale dielectric and conductivity imaging. J. Micromech. Microeng. 22, 115040 (2012).
Marchioro, A. et al. Unravelling the mechanism of photoinduced charge transfer processes in lead iodide perovskite solar cells. Nat. Photonics 8, 250â255 (2014).
Hutter, E. M., Eperon, G. E., Stranks, S. D. & Savenije, T. J. Charge carriers in planar and meso-structured organicâinorganic perovskites: mobilities, lifetimes, and concentrations of trap states. J. Phys. Chem. Lett. 6, 3082â3090 (2015).
Reid, O. G., Yang, M., Kopidakis, N., Zhu, K. & Rumbles, G. Grain-size-limited mobility in methylammonium lead iodide perovskite thin films. ACS Energy Lett. 1, 561â565 (2016).
Ihly, R. et al. Efficient charge extraction and slow recombination in organicâinorganic perovskites capped with semiconducting single-walled carbon nanotubes. Energy Environ. Sci. 9, 1439â1449 (2016).
Li, F. et al. Ambipolar solution-processed hybrid perovskite phototransistors. Nat. Commun. 6, 8238 (2015).
Bube, R. H. Photoelectronic Properties of Semiconductors (Cambridge University Press, Cambridge, UK, 1992).
Herz, L. M. Charge-carrier dynamics in organic-inorganic metal halide perovskites. Annu. Rev. Phys. Chem. 67, 65â89 (2016).
Zhao, T., Shi, W., Xi, J., Wang, D. & Shuai, Z. Intrinsic and extrinsic charge transport in CH3NH3PbI3 perovskites predicted from first-principles. Sci. Rep. 6, 19968 (2016).
Rothmann, M. U. et al. Direct observation of intrinsic twin domains in tetragonal CH3NH3PbI3. Nat. Commun. 8, 14547 (2017).
Wang, G. et al. Wafer-scale growth of large arrays of perovskite microplate crystals for functional electronics and optoelectronics. Sci. Adv. 1, e1500613 (2015).
Acknowledgements
The work at UT-Austin led by X.L. and K.L. is supported by NSF EFMA-1542747. Z.C. and D.W. also acknowledge the support from Welch Foundation Grant No. F-1814. The work at the National Renewable Energy Laboratory was supported by the U.S. Department of Energy under Contract No. DE-AC36-08-GO28308. K.Z., M.Y., and P.S. acknowledge the support by the hybrid perovskite solar cell program of the National Center for Photovoltaics funded by the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Solar Energy Technologies Office.
Author information
Authors and Affiliations
Contributions
K.L., X.L., and K.Z. conceived the project. M.Y., P.S., and K.Z. prepared samples and performed optical measurements. Z.C., X.M., and J.S. conducted the MIM measurements. Z.C. and K.L. performed data analysis and drafted the manuscript. The manuscript was written through contributions of all authors. All authors have given approval to the final version of the manuscript.
Corresponding authors
Ethics declarations
Competing interests
K.L. holds a patent on the MIM technology, which is licensed to PrimeNano Inc. for commercial instrument. The terms of this arrangement have been reviewed and approved by the University of Texas at Austin in accordance with its policy on objectivity in research. The remaining authors declare no competing financial interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the articleâs Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the articleâs Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Chu, Z., Yang, M., Schulz, P. et al. Impact of grain boundaries on efficiency and stability of organic-inorganic trihalide perovskites. Nat Commun 8, 2230 (2017). https://doi.org/10.1038/s41467-017-02331-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-017-02331-4
This article is cited by
-
Revealing the impact of organic spacers and cavity cations on quasi-2D perovskites via computational simulations
Scientific Reports (2023)
-
High-quality CsPbBr3 films prepared by introducing methylammonium iodide into PbBr2 precursor for efficient perovskite solar cells
Journal of Materials Science: Materials in Electronics (2023)
-
Effectively modulating thermal activated charge transport in organic semiconductors by precise potential barrier engineering
Nature Communications (2021)
-
Microwave impedance microscopy and its application to quantum materials
Nature Reviews Physics (2021)
-
Superior photo-carrier diffusion dynamics in organic-inorganic hybrid perovskites revealed by spatiotemporal conductivity imaging
Nature Communications (2021)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.