GDM 850 Drillmec Manual Spanish

850 TON TOP DRIVE
Manual De Mantenimiento
SN054
850 Ton TOP DRIVE
Manual de
Mantenimiento
Premium Oilfield
Drilling Equipment and Support
9841 Windmill Park Ln
Houston, Texas 77064
Phone 713.623.1449 • Fax
281.416.4495
GDM 850 - DRILLMEC
Tabla de Contenido
Seccion 1 – General ............................................................................................. 1-1

• Uso del manual
• Especificaciones del Top Drive
• Datos del Torque
Seccion 2 – Mantenimiento e Inspección .......................................................... 2-1

• Diagrama de Mantenimiento del Top Drive
• Inspección
• Mantenimiento
• Inspección de componentes de carga
Seccion 3 – Diagramas y Partes ......................................................................... 3-1

• Índice
• Diagramas de Ensamblaje
• Diagramas Electricos
• Diagramas Hidraulicos
• Partes de Repuesto
Seccion 4 – Manual de Prevención de Caídas de Objetos ................................... 4-1
• Manual de Prevención de Caídas de Objetos
Seccion 5 – Certificaciones .................................................................................5-1

• Certificado de Conformidad
• Certificado de Registro API
• Licencia API
• Certificado de Origen
GDM 850 - DRILLMEC
Section
1
T he GDM (Global Drilling Machine) línea de Top Drives, Resuelve muchos de los problemas que
reducen el rendimiento y la fiabilidad de los modelos de top drive convencionales. La línea de Top Drives
GDM ofrece un simple y robusto diseño mecánico que minimiza los puntos de falla, mejorando el
rendimiento en Torque y RPM y permite un acceso más fácil a zonas de mantenimiento
General
Contenido
Uso del Manual 1-2
Especificaciones del Top Drive 1-3
Datos del Torque 1-4
1-1
GDM 850 - DRILLMEC
Uso del Manual

Este Manual está Organizado de la siguiente manera:
Seccion Descripcion
Contiene un resumen de este manual y define los términos de precaución;

1 – General
También describe Especificaciones del Top Drive y como encontrar
información.
2 – Mantenimiento
Describe los requisitos y rutinas de mantenimiento e inspección
e Inspeccion
3 – Diagramas y Contiene Diagramas de Ensamblaje, Diagramas Eléctricos, Diagramas

Partes Hidráulicos Diagramas de Lubricación. Partes mostradas en los Diagramas con
su respectivo número de parte.
4 – Prevención de Contiene estándares y prácticas para retención secundaria

Caídas de Objectos
5 – Certificaciones Certificados de Conformidad y Premium’s API Certificaciones y Licencias
Importante Información de Seguridad

A lo largo de este manual, se utilizan los siguientes términos de precaución. Es importante que sus
significados se entiendan completamente antes de continuar:
ADVERTENCIA (WARNING)– Este término precede inmediatamente o sigue

cualquier instrucción de procedimiento o información que, si no se cumple correctamente,
presenta el potencial de causar lesiones al personal o la muerte.
PRECAUCION (CAUTION) – Este término se refiere a cualquier técnica o procedimiento

que, si no se cumple correctamente, presenta el potencial de causar danos a las piezas o al
equipo incluyendo fallas catastróficas
NOTA (NOTE) – Este término se usa para enfatizar información importante.
1-2
GDM 850 - DRILLMEC
Especificaciones del Top Drive

GDM 850
Carga de Peso Estatico 850 Toneladas Cortas

Motor Electrico de Perforacion DMX175
Maxima Corriente Continua 1200 Amps
Maxima Corriente Intermitente 1450 Amps (15 Seconds)
Maximo Voltage 575 Volts
Rango de Frecuencia 40.6 Hz
Sistema de Enfriamiento 15 HP Soplador abordo
Caballos de Fuerza Continuo 1200 HP
Relacion de Transmision 8.1765 : 1
Torque Continuo 65,000 Ft/Lbs.
Capacidad del Freno 50,000 Ft/Lbs.
Maximo Torque de Desconexion 100,000 Ft/Lbs. MAXIMO
Capacidad de sujeción a la tubería 100,000 Ft/Lbs.
Orientación del Manipulador de Tubería 360˚/Ilimitado – con Candado Hyd
Conexion del Eje Principal 7 5/8” Reg.
Diámetro interior del paso del lodo 3” inches
Máxima Presión del paso de lodo 7,500 PSI
Actuador Remoto IBOP 10,000 PSI
Actuador Manual IBOP 10,000 PSI
Carrera del contrabalance 7.25” inches
Peso en el Gancho con el Extend Frame 53,000 Lbs.
Altura 25' with 144" Elevators
Anchura * Profundidad 4.4' * 5.6'
Sistema de Lubricacion 2HP 5GPM Flujo
Sistema Hidraulico 2,350 PSI at 13 GPM Flujo
1-3
GDM 850 - DRILLMEC
Datos del Torque
GDM-850 TON TOP DRIVE PERFORMANCE CURVE -- 1,200 HP

90000
BREAK OUT
85000 81,482 FT-LB
80000
75000
70000
65000
CONSTANT TORQUE
60000
64,921 FT-LB Continuous to
55000
99 RPM.
TORQUE (FT-LB)
50000
45000
CONSTANT HORSE POWER
40000 To Max Motor Speed
35000
30000
25000
20000
15000
10000
5000
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200
TOP DRIVE SPEED (RPM)
GDM 850 - DRILLMEC
2
Seccion
Mantenimiento e Inspección
Contenido
Diagrama del Mantenimiento del Top Drive 2-3
Figura 6 – Puntos de Mantenimiento 1 2-3
Mantenimiento 2-6
Manual del Motor Electrico y Generador 2-6
Lubricación 2-38
Aceite Hidráulico 2-38
Filtración
2-38
Grasa
Top Drive Caja de Engranajes 2-39
Top Drive Caja de Engranajes capacidad de aceite 2-40
Inspección 2-41
Programas Recomendado de Inspección 2-42
Categoría I Inspección 2-43
Categoría II Inspección 2-43
Categoría III Inspección
2-43
Categoría IV Inspección
Frecuencia de Inspección 2-44
Inspecciones Periódicas 2-44
Inspecciones No Periódicas 2-44
NDT Inspector Certificados 2-45
Criterio de Aceptación
Inspección y Mantenimiento por Desalineamiento del 2-46
Top Drive con el Centro del Pozo 2-47
Página de la Categoría de Inspección
2-48
Inspección después de Periodos de Condiciones Severas
de Perforación 2-51
Inspección de la Pre-Carga de los Rodamientos 2-52
Principales 2-53
Inspección de la Pre-Carga de los Rodamientos del Piñón 2-54
Inspección del Tubo Lavador (Wash-pipe)
2-54
Inspección del Freno de Disco del Top Drive
GDM 850- DRILLMEC Rev. 1 2-1

GDM 850 - DRILLMEC
Listado de Mantenimiento 2-55

Inspección de componentes de 2-56
Carga 2-63
Componentes de Carga

Diagrama de Mantenimiento del Top Drive
Figura 6 – Punto de Mantenimiento 1
Pastillas de Freno
Punto de Engrase Pastillas del freno,

Motor Golf Electric Examinar por desgaste y
NOTA: holgura entre el disco
Referirse al manual del Semanal
fabricante pare el tipo de
grasa e intervalos de engrase
Punto de engrase
Cople del Motor
10 bombazos (GDM P/N:
C100177) Kop Flex grasa
Cada 3 Meses
Boquillas aspersores de
Lubricación
Remover e inspeccionar por
obstrucciones
Mensual o en el cambio de
aceite
Cambio de Aceite de
Engranes
(Aceite: Meropa, ISO150/220)
en la caja de Engranes
Filtro colador tipo Y Cada 3 Meses o por análisis
Limpiar e de aceite
Inspeccionar
Semanal
NOTA:
Consultar el Listado de
Punto de Engrase
Collar de Carga (1 Place) Mantenimiento en
15 Bombazos (NLGI #2) Pagina
Semanal
2-55
2-3
Inspeccionar el respiradero Punto de Engrase

en la tapa de la caja de Pernos de block viajero
engranes por obstrucciones lubricar en la instalación
Diariamente
Punto de Engrase
Tubo Lavador (1 lugar)
Cada 12 Horas
Punto de Engrase
Sellos Inferiores (2 lugares)
Semanal
Inspeccionar el nivel de
aceite: el nivel es en la parte
inferior del engrane principal
cuando la bomba está en
funcionamiento
Cada 12 Horas
Punto de Engrase
Engrane de Giro (2 Lugares) tapón de Drenado caja de
Aplicar Grasa & Rotar Engranes (#12) Sellos
10 bombazos por conector inferiores
Semanal limpieza
(Referencia)
Punto de Engrase
Rodamiento del Cilindro Punto de Engrase
(2 lugares) Guia Estabilizadora
Semanal (4 lugares)
Diariamente
Punto de Engrase Punto de Engrase

Actuador Remoto (4 Lugares) Perno de puerta de la
Cada 12 Horas mordaza
(2 lugares)
Diariamente
2-4
Punto de Engrase
Perno del cilindro NOTA:
(4 lugares) Aplicar grasa en el
Semanal
interior de las bridas de
las viga
Punto de Engrase Punto de Engrase

Pernos de orejas del cuadro Ajustadores de las correderas
(8 Lugares) guias (8 Places)
Semanal Semanal
2-5
INSTALLATION & OPERATING MANUAL JULY 2022
REVISION 01
DRILLMAX 175T MOTOR
DOCUMENT NUMBER REV
IOM DMX175T 01
SUBJECT TO CHANGE WITHOUT NOTICE 1 of 33

Form MM 6.002-1
Gulf Electroquip
425 North Wayside Drive ONLINE gulfelectroquip.com PHONE +1 713-675-2525 FAX +1 713-675-6433
Houston, Texas 77020-7598 USA
REVISION 01
DRILLMAX 175T MOTOR
Gulf Electroquip Ltd.

425 North Wayside Drive
Houston, Texas, USA 77020-7598
Telephone: (713) 675-2525
Email: sales@gulfelectroquip.com
© Copyright 2022 Gulf Electroquip

All rights reserved throughout the world.
Specifications subject to change without notice.
® Gulf Electroquip and the Gulf Electroquip Brand Mark are registered trademarks of Gulf
Electroquip Ltd.
Printed in U.S.A.
REVISION HISTORY
01 07/25/2022 General Refinements K.V. S.V
00 05/31/2022 Initial Release S. V. K.V

Rev Date Reason for issue / Desc of Change Prepared Checked Approved

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
TABLE OF CONTENTS
1 INTRODUCTION AND DESCRIPTION......................................................................................... 5

1.1 Introduction ...................................................................................................................... 5
1.2 Safety Overview ................................................................................................................ 5
1.3 List of terms and symbols ………………………………………………………………………...8
1.4 Motor data & description ................................................................................................... 9
1.5 Motor Safety Information ………………………………………………………………………..10
2 GENERAL INSTRUCTIONS ....................................................................................................... 12
2.1 Application ..................................................................................................................... 12
2.2 Transportation ................................................................................................................. 12
2.3 Receiving ........................................................................................................................ 12
2.4 Storage & Removal ......................................................................................................... 12
2.5 Handling .......................................................................................................................... 13
2.6 Insulation Resistance ...................................................................................................... 14
3 INSTALLATION, START UP AND OPERATION ........................................................................ 14
3.1 Inspection ....................................................................................................................... 14
3.2 Support Structure & Alignment ........................................................................................ 14
3.3 Installation of motor ......................................................................................................... 16
3.4 Start-Up Procedure ......................................................................................................... 19
3.5 Operating Information ..................................................................................................... 19
4 MAINTENANCE ......................................................................................................................... 20
4.1 Inspection Procedure ...................................................................................................... 20
4.2 Preventive Maintenance Schedule .................................................................................. 21
4.3 Cleaning the Motor .......................................................................................................... 21
4.4 Drying Procedure ............................................................................................................ 23
4.5 Methods of Drying ........................................................................................................... 23
4.6 Maintenance Record ....................................................................................................... 23
4.7 Bearing Lubrication ......................................................................................................... 24
Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4.8 Troubleshooting .............................................................................................................. 25

5 APPENDICES ............................................................................................................................ 28
5.1 Motor GAD & Outline ...................................................................................................... 28
5.2 Nameplate (sample) ........................................................................................................ 29
5.3 Bolt torque specification …………………………………………………………………………30
5.4 Spares list …………………………………………………………………………………………31
5.5 Torque-speed curve ……………………………………………………………………………...32
6 WARRANTY TERMS……………………………………………………………………………………….33

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
INTRODUCTION AND DESCRIPTION
1.1 Introduction
This manual contains instructions for installing, operating, maintaining, and troubleshooting of the
various induction motors built by Gulf Electroquip in Houston, Texas. This section of the manual is general
in scope and designed to be used with product specific data and attachments, which provides detailed
information in relation to a specific model or series of motors.
1.2 Safety Overview

This manual contains general procedures that apply to Gulf Electroquip Motor products. Be sure to read
and understand the Safety Notice statements in this manual. For your protection, do not install, operate, or
attempt to perform maintenance procedures until you understand the Warning and Caution statements.
A Warning statement indicates a possible unsafe condition that can cause harm to personnel.
A Caution statement indicates a condition that can cause damage to equipment.
High Voltage warning – Connections that might be energized.
Important
This manual describes general guidelines that apply to most of the motor products shipped by Gulf
Electroquip. If you have a question about a procedure or are uncertain about any detail, DO NOT
PROCEED.
Please contact the Gulf Electroquip office for more information or clarification.
Before you install, operate or perform maintenance, become familiar with the following if applicable to your
area:
• NEMA Publication MG1 and MG-2, Safety Standard for Construction and guide for Selection,
Installation and Use of Electric Motors and Generators.
• IEC 34−1 Electrical and IEC72−1 Mechanical specifications
• ANSI C51.5, the National Electrical Code (NEC) and local codes and practices.
Safety Notice:
This equipment contains high voltage! Electrical shock can cause serious or fatal injury.
Only qualified personnel should attempt installation, operation and maintenance of electrical equipment.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
Do not touch electrical connections before you first ensure that power has been disconnected.
Electrical shock can cause serious or fatal injury. Only qualified personnel should attempt the installation,
operation and maintenance of this equipment.
The Adjustable Speed Controller may apply hazardous voltages to the motor leads after power to the
controller has been turned off. Verify that the controller is incapable of delivering hazardous voltages and
that the voltage at the motor leads is zero before proceeding. Failure to observe this precaution may result
in severe bodily injury or death.
Be sure the system is properly grounded before applying power. Do not apply AC power before you
ensure that all grounding instructions have been followed. Electrical shock can cause serious or fatal
injury. National Electrical Code and Local codes must be carefully followed.
Avoid extended exposure to machinery with high noise levels. Be sure to wear ear protective devices
to reduce harmful effects to your hearing.
Surface temperatures of motor enclosures may reach temperatures which can cause discomfort or
injury to personnel. When installing, protection should be provided by the user to protect against
accidental contact with hot surfaces. Failure to observe this precaution could result in bodily injury.
This equipment may be connected to other machinery that has rotating parts or parts that are driven
by this equipment. Improper use can cause serious or fatal injury.
Do not by-pass or disable protective devices or safety guards. Safety features are designed to
prevent damage to personnel or equipment. These devices can only provide protection if they remain
operative.
Avoid the use of automatic reset devices if the automatic restarting of equipment can be hazardous to
personnel or equipment.
Be sure the load is properly coupled to the motor shaft before applying power. The shaft key must be
fully captive by the load device. Improper coupling can cause harm to personnel or equipment if the load
decouples from the shaft during operation.
Use proper care and procedures that are safe during handling, lifting, installing, operating and
maintaining operations. Improper methods may cause muscle strain or other harm.
Incorrect motor rotation direction can cause serious or fatal injury or equipment damage. Be sure to
verify motor rotation direction before coupling the load to the motor shaft.
Motors that are to be used in flammable and/or explosive atmospheres must display the appropriate
listed logo.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
Pacemaker danger − Magnetic and electromagnetic fields in the vicinity of current carrying
conductors and motors can result in a serious health hazard to persons with cardiac pacemakers, metal
implants, and hearing aids. To avoid risk, stay away from the area surrounding this electrical equipment.
Before performing any motor maintenance procedure, be sure that the equipment connected to the
motor shaft cannot cause inadvertent shaft rotation. If the load can cause shaft rotation, disconnect the
load from the motor shaft before maintenance is performed. Unexpected mechanical rotation of the motor
parts can cause injury or motor damage.
Guards must be installed for rotating parts such as couplings, pulleys, external fans, and unused
shaft extensions, should be permanently guarded to prevent accidental contact by personnel. Accidental
contact with body parts or clothing can cause serious or fatal injury.
It is recommended to use a shielded motor power cable with a complete circumferential braided or
copper film/tape ground jacket around the power leads. This ground should be secured to the motor frame
from within the motor terminal box and must return without interruption to the drive ground. In addition, if
the motor and coupled equipment are not on a single common metal base plate, it is important to equalize
the equipment ground potentials by bonding the motor frame to the coupled equipment using a high
frequency conductor such as a braided strap.
Do not over grease motor as this may cause premature bearing failure.
The motor lifting hardware is adequate for lifting only the motor. Do not lift the motor and its driven
equipment by the motor lifting hardware. Disconnect the load (gears, pumps, compressors, or other driven
equipment) from the motor shaft before attempting to lift the motor.
If eye bolts are used for lifting a motor, be sure they are securely tightened. The lifting direction
should not exceed a 20° angle from the shank of the eye bolt or lifting lug. Excessive lifting angles can
cause damage.
To prevent equipment damage, be sure that the electrical service is not capable of delivering more
than the maximum motor rated amps listed on the rating plate.
If a HI POT test (High Potential Insulation test) must be performed, follow the precautions and
procedure in NEMA MG1 and MG2 standards to avoid equipment damage.
Do not operate motors with a roller bearing unless a sufficient radial load is applied so that damage
to the roller bearing does not occur.
If you have any questions or are uncertain about any statement or procedure, or if you require additional
information please contact Gulf Electroquip.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
1.3 List of Terms and Symbols
Active or Live Part: Indicates that a conductive piece of the motor is currently connected to electrical
power which energizes the motor. This generally occurs during normal operation, start-up and shutdown
of the motor.
Authorized Personnel: Refers to an employee that has been given formal approval by the company to
train other personnel to maintain, operate, setup and teardown a motor.
GEQ: Refers to the company name Gulf Electroquip Ltd.
Grounded: Indicates that a conductive piece of the motor is currently connected to the grounding
system of the motor.
Leads: Are the main motor power connections and are typically supplied by the customer.
Left Side : Refers to the left side position of the motor on board a top drive drilling rig.
Outfitted motor: Refers to a motor that has been outfitted per the customer specification, which can
include a braking system, blower, junction box, drive pinion, brake pinion and any other parts as
specified.
Pinion: Either the drive gear/hub and/or the brake hub that may be attached to the motor shaft.
Qualified Personnel: Refers to an employee that has been trained by authorized personnel to handle
maintenance, setup, operation and teardown of a motor.
Right Side : Refers to the right-side position of the motor on board a top drive drilling rig.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
1.4 Motor Data & Description
Rated Output 1200 HP
Rated Voltage 575 V
Rated Frequency 40.6 Hz
Base Speed 812 RPM
Max Speed 2300 RPM
Duty Top Drive
Maximum Current at Full Load 1227 Amps
Efficiency 90.1%
Number of Poles 6
Full Load Torque 7940 FT LBS
Ambient Conditions 40°C
Maximum Altitude 3000 FT
Upper Bearing 6326 – Ball Bearing
Lower Bearing NU330 – Roller Bearing
Cooling Forced Ventilated
Enclosure, Motor: DPG-FV

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
A 3-phase induction motor has two main parts: A static part called the stator, and a revolving part called
the rotor. The rotor is separated from the stator by the presence of a thin air gap. The stator consists of a
fabricated steel frame that houses and secures the laminated stator core. The stator core is made from
thin insulated laminations stacked to form a hollow cylindrical stack. At the air gap, along the inner
circumference of the laminations, are evenly spaced slots that contain the stator winding (formed coil).
The rotor core is made up of thin, insulated laminations stacked to create openings (slots) at the rotor
OD. Extruded copper rotor bars are inserted into the rotor slots and connected (brazed) at each end by
copper short circuit rings. The copper bars are swaged in this position to the slot to avoid movement as a
countermeasure against sparking and vibration. The rotor bars resemble a cage and is sometimes
referred to as a “squirrel cage” rotor.
The entire rotor core is secured to the shaft through an interference fit and the combined rotor and
shaft assembly rotates between bearings supported at each end of the motor frame.
1.5 Motor Safety Information
This motor is designed with the ability to operate within a potentially hazardous area. It is required that
the equipment shall be installed in compliance with all industry, national, and site safety standards. It is
the responsibility of the end user to ensure the equipment meets or surpasses these standards.
The installation, operation, and maintenance of the motor must only be carried out by qualified or
authorized personnel. Read and understand this manual in its entirety before proceeding. This is a high
voltage (575V) unit with a risk of shock that may cause potential bodily injury or loss of life. The motor
should be disconnected from any power supply and come to a complete rest before attempting any
installation or maintenance procedures.
Included Safety Features

 Safety wires and bolts are included with the motor. After completing installation of the motor, ensure
that all bolts have safety wire in place in order to protect personnel from falling objects.
 Thermal Protectors are included. These thermal protectors are temperature devices installed into
the windings of the motor and are intended to be used with the motor drive system. If the motor
winding temperature should rise above class H limits, the winding insulation life may become
shortened.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
Qualified and/or authorized personnel performing installation, maintenance or removal of this electrical
motor should always use Personal Protective Equipment (PPE) and follow all company safety policies.
Recommended Safety Features

 A safety lockout to isolate the motor and prevent the motor from starting during inspection and
maintenance.
 An interlock integrated into the controls of the motor that will ensure that the heaters are not
energized during motor operation.
 An interlock using a pressure switch to ensure that the cooling blower is running whenever the
motor is energized in order to continually cool the motor.
Under normal operating conditions, the motor electrical connections meet the requirements of IEC
Standards for safe operation. To ensure safe operation, the ingress of contamination or water should be
avoided. It is the responsibility of the end user to ensure the motor and auxiliaries are suitable for the
environment in which the equipment is to be operated. Failure to do so can result in electrical shock,
bodily injury, or loss of life.
This motor has a high voltage circuit, rotating parts and the frame of the motor can reach temperatures
high enough to cause injury or death of an individual during operation. Please ensure that all safety
precautions are taken while the motor is sitting idle, energized in operation or otherwise.
Should there be any questions or concerns about the safe operation of the motor, please contact Gulf
Electroquip (GEQ) at the following location:
Gulf Electroquip, Ltd.

425 North Wayside Ave.
Houston, Texas 77020
Phone 713-675-2525 [24/7/365]
Website: http://www.gulfelectroquip.com

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
GENERAL INSTRUCTIONS
2.1 Application
Gulf Electroquip DRILLMAX motors have been engineered to satisfy a wide range of applications within
the oilfield industry for drilling applications. The motor was developed to meet required specifications of
the IEC 60034-1 standard.
2.2 Transportation
Secure the motor tightly with shipping braces to make certain that it is does not shift during shipping and
result in damage to the motor.
2.3 Receiving
Thoroughly inspect the equipment before accepting shipment from the transportation company. If any of
the goods called for in the bill of lading are damaged or the quantity is short, do not accept them.
Promptly notify the freight company and make an appropriate notation on the freight bill. If any
concealed damage is discovered later. Notify the freight or express agent at once and request them to
make an inspection. Claims for loss or damage in shipment must not be deducted from the GEQ invoice,
nor should payment of the GEQ invoice be withheld awaiting adjustment of such claims, as the carrier
guarantees safe delivery.
Be sure to use the following procedure to ensure proper shipment upon receiving the motor:
1. Remove all packaging material, inspect and clean shaft surfaces, machined fits, rotate the shaft
by hand to check for any obstructions.
2. Remove any cover plates and inspect the interior for dirt or damage, loose connections, etc.
3. Reinstall cover plates and gaskets.
2.4 Storage/ Removal

Motors are to be stored in a clean and dry location, free from extreme temperatures and away from
corrosive and humid environments. The following preparations and maintenance should be followed for
proper storage:
1. Before placing the motor into storage, use a Meg-ohm meter to measure the insulation
resistance from the motor winding to ground. Record these values and store with the motor
manual and/or data sheets. The minimum acceptable reading is 2 megaohms.
2. Apply rust inhibitor to unpainted and machined steel surfaces.
3. Package the motor to prevent the ingress of dust and moisture (i.e., seal inside plastic heat
wrap); include desiccant inside the packaging to help prevent the formation of condensation.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4. While in storage, the motor space heaters should be energized. Please refer to the outline
drawing of the manual.
5. During storage it is necessary to rotate the shaft by hand at least 20 revolutions per month.
6. During storage the bearings should be lubricated every 6 to 9 months.
Upon removal from storage, be sure to do the following:

1. Disconnect heater connections, perform Insulation resistance test. If the insulation resistance
reading has deteriorated more than 50% of the reading before storage, the motor must be
electrically or mechanically dried. Refer to information contained in this manual on drying the
windings (paragraph 4.5).
2. Rotate the shaft a minimum of 20 revolutions to redistribute the lubricant.
3. If required, lubricate per the lubrication nameplate instructions.
NOTE: If the motor is stored for one year or longer, it must be returned to manufacturer for bearing
and seal inspection and reconditioning.
Improper storage of electrical machines can result in seriously reduced reliability. Though precautions
are taken at the factory, if the motor is exposed to a humid atmosphere, the bearing or surrounding
area can rust, potentially contaminating the bearing. If stored improperly, the electrical insulation may
absorb an excessive amount of moisture leading to the motor winding failing to ground.
2.5 Handling
Lifting and handling should be completed using the appropriate lifting points. For this reason, lifting lugs
are incorporated into the frame design to provide for lifting the motor in its horizontal orientation. Any
handling straps for lifting or shipping should be placed on the body/frame of the motor.
The motor shaft should never be used for lifting. Damage to the shaft surfaces can place an axial,
stationary or shock load on the bearings and may result in improper motor operation. Improper handling
of the motor that results in damage will void the warranty.
The provided lifting lugs and lug features are intended for lifting the motor only. These lifting points
should not be used on a motor with installed accessories i.e. a junction box, blower or brake assembly.
Failure to observe this precaution may result in bodily injury.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
2.6 Insulation Resistance
Throughout the life of the motor, it will be necessary to test the state of the motor’s insulation. This
procedure is best completed using a Meg-ohm meter. The test generally consists of detaching all the
leads from the motor and attaching one lead to a Meg-ohm meter and the other side of the meter to
ground. Use a Meg-ohm meter with a minimum of 500 VDC output and is capable of taking resistance
readings to ground. For more information on how to run this test, please do not hesitate to contact Gulf
Electroquip. The following chart can be used to assess the state of the motor insulation. Winding
insulation resistance measurements will be in units of megaohms.
INSTALLATION, START UP AND OPERATION
3.1 Inspection
Before installing the motor, it is recommended that the unit be thoroughly inspected for indications of
damage or potential malfunctions. Carefully examine the exterior surfaces of the motor for deep
scratches, dents, damaged guards, loose or missing bolts, screws and other attaching parts. Remove
the screens, louvers or covers from the ends of the motor and inspect the rotor and stator and other
internal components for loose or damaged windings and lead wires, loosely mounted components, and
the presence of moisture or other foreign material.
Remove all shipping materials such as blocks, straps, tapes, rubber packing, paper or other material
used to restrict movement of the rotor during shipment. Use low pressure compressed air, 25 PSI
maximum, to blow out all packing residue and dust from the interior of the motor. Turn the rotor by hand
to make certain that the shaft rotates smoothly and without binding.
3.2 Support Structure & Alignment

The support structure for the motor must be rigid, level and of ample size and strength to support the weight
of the motor and withstand the reaction loads the motor will impart. The support structure must also be
adequately designed to maintain coupling alignment between the motor and driven load. It is very important
that the support structure is designed in such a manner as to not have any resonant operating frequencies
at or near the operating speed, or at multiples of the operating speed of the unit.
Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
The motor and driven load should be located and leveled on the mounting base. Care should be taken to
eliminate any misalignment resulting from parallel, angular, axial or a combination of misalignments. Dial
indicators and micrometers shall be used to align the motor shaft and the driven load to eliminate any
misalignment conditions during installation. In arrangements where the motor uses a pinion mounted on the
drive end and is directly coupled to a gearbox, care shall be taken to strictly adhere to the equipment
manufacturer’s manual (top drive manual) to ensure parameters like backlash, mounting distance, gear
contact percentage, axial end play, etc. are within specified parameters.
Soft foot is the condition where the motor does not sit flat on its base and only three of the four mounting
points support the motor. When the fourth mounting point is clamped down the motor frame or mounting
skid is distorted causing possible vibration or erroneous alignment information. Soft foot can be corrected by
loosening each mounting point one at a time, measuring the relative movement with a dial indicator, and
shimming under the foot to eliminate that relative movement. Care shall be taken during installation to
eliminate “soft foot condition”.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
3.3 Installation
Please review the following list before attempting to install the motor:
1. Complete the inspection of the motor prior to installation. If the motor requires a pinion and/or a
brake hub, these must be installed before installing the motor on the top drive assembly.
2. Please follow the instructions for lifting the motor per the installation manual. Remove access
covers from the motor as needed before lifting.
3. The GEQ DMX175T motor is designed to operate in the vertical position with the drive hub
mounted on the bottom side and the brake assembly (customer-supplied) mounted on the top side.
Mount the motor to a secure, substantial structure to be sure the motor does not vibrate
excessively during operation. Be careful not to damage the surface of the interfacing components,
the motor shaft or to allow the motor to collide with any structures while the motor is suspended
from a crane during the installation process.
4. Once the motor is close to the desired position, be careful to align the interfacing components and
the mounting surfaces. Check that the motor is in the proper orientation and that the motor will
have the correct direction of rotation.
5. Bolt the motor into place using the mounting bolts. Torque all bolts to specifications listed in the
Appendix of this manual.
6. With the motor securely bolted in place, the next step is to connect the three (3) electrical power
leads of the motor. This motor has tabbed connections within the motor frame.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
7. Care shall be exercised when connecting the starting device phase leads to the motor. The leads
must have the proper sequence applied by the Variable Frequency Drive (VFD) to obtain the
desired motor direction of rotation. Interchanging the phase sequence of any two of the power
supply leads will produce rotation in the opposite direction.
NOTE!
If there is any doubt about rotation and phasing, the motor can be “bumped” to indicate the
direction of rotation by momentarily energizing the motor. A minimum of two people should
check this, one at the motor and one at the starting device with good visual/oral communication
via radio. For “bumping” the motor to determine rotation, the starting device should energize the
motor only as long as it takes to cause the motor to “break-away” and begin to rotate. If the
rotation is incorrect, remove power from motor and allow motor to coast to a stop. Reverse
phase sequence of the power supply connections to the motor for desired direction of rotation.
8. Next, it is necessary to wire in the recommended safety interlocks such as the control system,
thermal protection, air pressure safety switch, the speed encoder and any other safety systems
that the end user deems necessary.
9. Any other required and remaining mechanical or electrical systems should be installed at this time
(e.g., the motor cooling blower, braking equipment, motor speed encoders, etc.).
10. Space heaters (if provided with the motor) are mounted inside the DE end shield and should be
energized continuously only during motor storage. (Note: During start-up and operation of the
motor, the heaters must be de-energized.) See motor outline drawing for space heater wire
diagram and power information (If applicable)
11. The bearing housings are equipped with seals and include provisions for re-lubrication during
operation. Each bearing is equipped with a provision to mount one 100-ohm platinum resistance
temperature detector (RTD) for monitoring temperature. With the RTD, the temperature of the
bearings can be monitored during operation as the customer deems necessary. If RTDs are
monitored, the initial alarm point can be set at 100°C and shutdown initiated at 110°C. Otherwise,
if the established bearing temperatures are considerably lower, the alarm setting can be adjusted
to 10°C above the normal operating bearing temperature and the shutdown point can be set
another 10°C above the alarm.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
12. The stator of the motor is equipped with six 100 ohm platinum RTDs (embedded between the
stator coils), two per phase. The stator coils embedded in the laminated core receive a global VPI
of non-hygroscopic resin. The stator insulation system is Class H. The temperature of the stator
coils can be monitored during operation utilizing the RTDs that are installed inside the wound
stator assembly. For proper insulation protection, the RTD relays shall be initially set for alarm at
185°C, and shutdown at 195°C max.
13. Reinstall any access panels or exhaust covers that were removed during the unpacking of the
motor. At this time, it is completely necessary to run safety wires through heads of the bolts on the
exterior of the motor and secure all safety wire.
14. When completely assembled and installed on the top drive, this GEQ DRILLMAX motor will meet
an ingress protection rating of IP44 or better. Do not install any accessories on this system that do
not meet this standard. Please refer to IEC 60529 for additional information on ingress protection
ratings.
15. To complete the installation of the motor, it is now necessary to install the system ground wire onto
the motor. Please follow all local IEC codes for ground circuit sizing and installation.
Cabling used to connect to main motor terminals must have a temperature rating
greater than 110°C and shall be sized (size and insulation) for the maximum motor current.
Careful alignment of machines is essential to prevent excessive vibration, hot bearings, or shaft
failures. Interference fits shall be used between the motor shaft and the drive/brake hub.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
3.4 START UP PROCEDURE
1. After rotation is verified to be correct, the motor can be started using the variable frequency drive
(VFD). Verify all instrumentation are functional (as applicable), correct blower operation and ID
run the motor using VFD. Verify that there is no unusual noise or vibration present. Save the data
from the ID run.
2. Check the motor drive parameters full load amperes (AC amps) and confirm with the full load
current values listed in this manual. The phase currents should be balanced within +/- 5%.
3. Temperature-monitoring equipment (if provided with motor) must be available, monitor the stator
and/or bearing RTD temperatures for safe operation. Any sudden change in temperature on
either stator RTD’s or bearing RTD’s is cause for shutdown. Otherwise, temperature should
gradually rise and stabilize within approximately a 4-hour period.
4. Check the motor frame and enclosures for evidence of any excessive vibration. If the motor
frame or enclosures are vibrating excessively, the motor should be shut down and the cause of
vibration located and corrected.
5. Once the motor is started, it will remain at approximately the rated speed unless voltage is lost to
the main power terminals. The machine will trip the drive protection if the load applied to the shaft
is increased to a value outside of the normal operating limits or the torque of the load exceeds the
break down torque for which the motor is designed.
6. Normally, the VFD will contain relays to protect the motor from overcurrent, over temperature,
stall, and excessive torque. These relays will open and disconnect the motor from the electric
drive when abnormal conditions occur. Vibration detection devices may also be used to
disconnect the motor during excessive vibration events.
3.5 OPERATING INFORMATION
The motor is designed for use with a variable frequency drive (VFD). Please refer to the data in
Appendix or the motor nameplate for operating data to ensure that the drive is setup to run the motor at
rated motor electrical conditions.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
MAINTENANCE
4.1 Inspection Procedure

 Prior to beginning the inspection, the following suggested items should be available: Inspection
light, basic hand tools and wrenches, overhead lifting equipment, electric/pneumatic wire brush
suitable for the area classification, roughing/sanding pads, safety solvent, personal protective
equipment, etc. Inspections should be conducted by qualified personnel.
 Inspect exterior bolts – all bolts should be present, tight and free of rust and dirt. Bolts should not
show evidence of sparking (pitting, burned, or blackened areas or paint powdering would be
evidence of sparking). Clean and re-inspect.
 Remove end covers and side panels – inspect all mating surfaces, flange overlaps, and areas
where covers are adjacent to metal parts on motor exterior for indications of sparking or localized
heating. Clean and re-inspect.
 Inspect interior – look for evidence of sparking on interior joints, bearing brackets (end shields),
bearing bolts, etc. Clean and re-inspect.
 Inspect rotor – look for evidence of sparking at rotor bars, shorting rings, any rotor bolts, between
the rotor bars and the laminations at the edges of the slots at the end of the core and at each vent.
Clean and re-inspect.
 Inspect gaskets – look for evidence of damage to gaskets, replace them if missing, broken,
deformed or hardened.
 General inspection – while motor is open, inspect interior for cleanliness, insulation cracks, loose
bolts or brackets, leaks, or evidence of end-turn movement. Clean or schedule shop maintenance
as needed.
 Test – station observers should view internal joints and the rotor to stator air gap and start motor
while watching for sparks. Repeat test start if needed.
 Clean – using safety solvent, wire brush and roughing/sanding pads, clean both sides of mating
surfaces of air shields and end and side covers at bolt connection points. Be sure to clean both
metal components and not just under bolt heads. Bare metal should be showing.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4.2 Preventive Maintenance schedule

A routine preventive maintenance program must be practiced. This will ensure peak performance, extend
motor life and minimize or eliminate equipment breakdowns. The following preventive maintenance
schedule shall be used as a guide for establishing a preventive maintenance program for motors
operating under standard conditions. Specific operating conditions should be analyzed by the equipment
user and a preventive maintenance program established accordingly. The below maintenance plan is
provided as a guide.
Under standard operating conditions, the following inspections are to be performed every 30 days.
 With the motor stopped, clean the outside of the motor and its ventilation screens, to remove dirt,
dust, oil or other contaminants.
 With the motor stopped, inspect the motor for loose or damaged windings, cracked, burned or
broken insulation, loose mounting components, loose hold down bolts, and the presence of
moisture or other foreign material.
 With the motor stopped, inspect the area surrounding the bearings for signs of excessive leakage
of oil or grease. Lubricate the bearings in accordance with the recommendations set forth in this
manual.
 With the motor stopped, inspect the lead wires and control device wiring for cracked or damaged
insulation and loose terminals.
 With the motor running, inspect the motor control and monitoring devices for correct adjustment
and operation.
4.3 Cleaning the Motor

Cleaning the motor is essential to long-term motor life. When the drilling motor is unfastened and
dismounted from the machinery it is driving, accumulated dirt and oil buildup shall be removed. The
external motor surfaces shall be cleaned by steam cleaning. To clean the motor:
 Cover the motor air inlet and outlet with heavy plastic and tape in place. Ensure the interior motor
components are protected from spray during cleaning.
 Clean the external motor surfaces only when the drilling motor is removed from its machinery and
power is disconnected from the motor.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
PERSONNEL PERFORMING CLEANING PROCEDURES MUST WEAR

PROTECTIVE CLOTHING, GLOVES, AND EYE PROTECTION. FOLLOW LOCAL
PRACTICES AND PROCEDURES FOR CLEANING. FAILURE TO DO SO MAY
RESULT IN INJURY OR DEATH.
ALKALI AND CHLORINATED HYDROCARBON CLEANING SOLUTIONS SHOULD

NOT BE USED FOR CLEANING DRILL MOTORS DUE TO THE ADVERSE AFFECTS
ON MOTOR INSULATION. USE OF THESE SOLUTIONS MAY CAUSE MOTOR
FAILURE OR REDUCED MOTOR LIFE.
DO NOT SPRAY THE INTERNAL COMPONENTS OF THE MOTOR WITH A STEAM

CLEANER. MOISTURE CONTAMINATION MAY CAUSE MOTOR FAILURE OR
REDUCED MOTOR LIFE.
 Steam clean only the external surfaces of the motor. Do not direct the spray at motor openings or
the plastic covers.
 When steam cleaning is complete, let excess fluid drain from the motor.
 Remove plastic covers or protective covers and tape from the motor. Clean the inside of the motor
by using a vacuum cleaner or dry low pressure compressed air, 25 PSI maximum, to remove any
accumulation of dirt, dust, or other gritty particles. Stubborn deposits of grease, oil or similar
substances on the metal components that are located away and clear of the windings and
insulating components may be cleaned using a clean cloth moistened with a nonflammable
solvent.
 Deposits of grease, oil, or similar substances on the winding or insulating components should only
be removed with a clean dry shop cloth. Consult with GEQ in Houston, Texas if the winding or
insulating components are contaminated to an extent where wiping with a cloth will not remove
the contaminants.
Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4.4 Drying Procedure

If the motor has been subjected to extreme dampness during shipment, storage, or cleaning, a
procedure may be required to thoroughly dry all windings.
If the stator insulation resistance measures less than 2 megaohms, the machine must be dried out until
at least the minimum recommended resistance value is obtained. The drying-out process can be
accomplished by applying either external or internal heat as necessary to obtain an end-winding
temperature of 75°C (167°F) by thermometer.
4.5 Methods of Drying

The easiest and most convenient method of drying out a motor consists of placing the complete, or
partially disassembled, machine in an oven. External heat also can be applied by placing space heaters
beneath the motor so as to obtain an even distribution of heat along the length of the unit. Care must be
taken to provide adequate air circulation during the drying-out process to insure a complete and
thorough job.
The temperature of the motor should be raised slowly to avoid building up

excessive vapor or gas pressure, which could prove harmful to the insulation. Do
not exceed a temperature rise of 10°C (18°F) per hour.
Do not hurry the drying-out process. Never permit the temperature of the motor to
exceed the maximum allowable temperature rise marked on the name plate.
4. 6 Maintenance Record
It is advisable to maintain a record of the insulation resistance and humidity during measurements for
each motor. The measurements, taken at maintenance intervals, will provide a means of detecting a
gradual deterioration of the winding insulation. Such records should list the prevailing site conditions,
such as the test voltages, ambient temperature and humidity, at the time of each test since these
conditions will affect the results.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4.7 Bearing Lubrication
The bearings are lubricated with Shell GadusRail S2 Traction Motor Bearing grease. During construction at
the factory the bearings are packed with a reserve of grease.
Relubrication is required on the motor. Fittings are provided for both top and bottom bearings. A pressure
relief vent has access to the same bearing cavity; this should be removed, if possible, during the
relubrication process.
Each bearing should be relubricated with approx. 10 grams of grease every 6 months or 2500 hours of
operation, whichever occurs first. Do not over grease the bearings, damage can result from too much
grease in the bearings.
The vent should never have grease pumped into it; it will lose its ability to vent the grease cavity and result
in potential damage to the bearings. Should it become clogged with grease or other matter should be
replaced. Under no circumstances should the vent be cleaned with solvent.
If GadusRail grease is not available, please consult Gulf Electroquip or lubricant supplier for compatible
and suitable greases. It is strongly recommended that greases not be mixed.
At each lubrication interval and during preventive maintenance inspections, the grease seal area and
adjacent shaft area should be inspected for signs of excessive leakage. If excessive leakage is present,
the seals should be replaced, and the shaft and seal sleeves repaired or replaced as necessary.
Should it become necessary to remove the bearing from the motor, it should be thoroughly inspected for
wear or damage prior to re-installation and replaced if necessary. The seals of the bearing housing should
also be inspected for wear or damage and replaced if necessary. When re-installing the bearing, the
bearing should be hand packed with grease and the bearing housings should be packed to 1/2 to 2/3 full
with grease. Care should be taken to ensure that no foreign material is allowed into the grease, bearing or
bearing housing.
Monitoring of bearing temperature can provide a warning of an impending failure of a bearing and
prevent costly mechanical damage resulting from bearing failure. The operating temperature of a
bearing can vary depending on load, speed, and the amount of grease in the bearing. Monitoring of
bearing temperature should focus on a sudden increase in bearing operating temperature over
temperatures which have been observed as normal for a specific motor. A bearing should be closely
monitored if it reaches 230oF (110oC). The motor should be shut down and the bearing and seals
inspected. If the operating temperature of the bearing reaches over 257oF (125oC) the bearing should be
replaced. The described limits above are to be determined by measurement of the temperature by
resistance temperature detector (RTD).

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
4.8 Troubleshooting
The most important way to keep a unit running with very little down time is to set up a program for
intelligently analyzing the malfunctions, and making the necessary corrections. Although regular
preventive maintenance inspections are conducted, be alert between inspections for any signs of motor
trouble. When a minor problem is located, correct it immediately. Minor defects can result in costly
repairs and down time. Some of the more common symptoms, are found in the following chart.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
APPENDIX – Motor GAD & Outline

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
RATING NAMEPLATE (Example)

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
SPARES LIST
Below is a list of spare parts and corresponding part ID for reordering:
GEQ Part ID Description QTY per motor
254891 LIP SEAL 2
255383 DE BEARING 1
255470 ODE BEARING 1
254901 SEAL RING 1
254902 V-RING 1
Note – Spare parts are recommended to be replaced only at Gulf Electroquip.

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
BOLT TORQUE VALUES
Follow the below recommended tables as a guide for torque setting on fasteners.
SAE Grade 5

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
TORQUE SPEED CURVE

Form MM 6.002-1
Gulf Electroquip
REVISION 01
DRILLMAX 175T MOTOR
WARRANTY TERMS
Gulf Electroquip, Ltd., Electric Machinery & Equipment, Ltd., Red Claw, L.L.C. or whichever company the invoice for the goods or services specified is called “Seller.” The person or entity named in the
“Sold To” bland is called “Purchaser.”
Sale of any of the equipment or services of Seller, at the prices indicated heron, is expressly conditioned upon Purchaser’s acceptance of all the terms and conditions set forth in Seller’s Quotation and Confirmation
of Sale and Acknowledgment. Any statement of intent to purchase any such equipment or services, any Purchase Order, any shop work order release, or any direction to proceed with engineering, procurement, manufacturing or
shipment, shall constitute an assent to the prices and all terms and conditions and a representation that the Purchaser is solvent. Any additional or different terms, prices or conditions set forth in any communication from the
Purchaser, including any purchase order, are objected to by Seller and shall not be effective or binging unless assented to in writing and signed by an authorized representative of Seller.
LIMITED WARRANTY – SELLER WARRANTS ALL GOODS AND SERVICES SOLD HEREUNDER TO BE FREE FROM INHERENT ELECTRICAL OR MECHANICAL DEFECTS ON DATE OF SHIPMENT. SELLER
FURTHER WARRANTS THAT ON DATE OF SHIPMENT, THE EQUIPMENT WILL DELIVER ITS RATED OUTPUT AS INDICATED BY THE NAME-PLATE, PROVIDED THE EQUIPMENT IS PROPERLY CARED
FOR AND OEPRATED UNDER PROPER CONDITIONS, WITH COMPETENT SUPERVISTION AND ALL FOUR (4) CONDITIONS PRECEDENT LISTED IN THE FREE REPAIRS PARAGRAPH BELOW, ARE
SATISFIED. These warranties are extended to the immediate purchaser only and not transferable, provided however, that if the purchaser in the course of its usual business, transfers title or leases such apparatus (including
equipment incorporating such apparatus) without using the equipment, to a third party, such period shall run to such third party as if it were the Purchaser, subject to the provisions on transfer set forth in the RESTRICTIONS
Paragraph.
FREE REPAIRS – Provided that: (1) Seller’s personnel are present and participate in the start-up of the equipment; and (2) the equipment has been installed and operated under proper conditions; and (3) the equipment was
connected to its rated load; and (4) that NOTICE IN WRITING is given Seller by Purchaser or third party immediately when parts are found to be defective so that representative of the Seller may be present to inspect the equipment
when it is dismantled, PARTS FOUND TO BE DEFECTIVE WITHIN ONE (1) YEAR, (EXCEPT IN THE CASE OF DIESEL, GAS AND GASOLINE ENGINES, IN WHICH EVENT THE PERIOD OF TIME SHALL BE
NINETY (90) DATS), FROM THE DATE OF (I) SHIPMENT FROM SELLER, OR (II) START-UP OF THE EQUIPMENT, WHICHEVER DATE OCCURS FIRST WILL BE REPLACED OR REPAIRED, AT THE OPTION
OF SELLER, F.O.B. SELLER’S PLANT, HOUSTON TEXAS, FREIGHT PAID BY PURCHASER OR THIRD PARTY, FREE OF REPAIR CHARGE. PURCHASER’S FAILURE TO COMPLY WITH ALL TERMS OF
THE “FREE REPAIRS” AND “RESTRICTIONS” PARAGRAPHS SHALL ATUOMATICALLY VOID ANY WARRANTY PROVIDED BY SELLER.
RESTRICTIONS – No claims for damages or for labor done by others or parts furnished by others will be allowed unless authorized by Seller, in writing. THIS WARRANTY IS THE ONLY WARRANTY APPLICABLE
AND IS EXPRESSLY IN LIEU OF ANY WARRANTIES OTHERWISE IMPLIED BY LAW, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MURCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. PURCHASER AGREES THAT NO OTHER REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, HAVE BEEN MADE OR GIVEN AND THAT THE PROVISIONS
OF THE “FREE REPAIRS’ PARAGRAPH ARE THE SOLE AND EXCLSIVE REMEDIES TO BUYER FOR SELLER’S BREACH OF WARRANTY. No representations, claims, statements, advertising or
promotional activities made or conducted by Seller or Seller’s agents or representatives shall be binding upon Seller unless the same ar expressly set forth in the Quotation, the Confirmation of Sale and Acknowledgment or
in a subsequent written agreement signed by Seller. In the event the equipment sold fails to comply with any warranty set forth herein or imposed by law and provided Purchaser complies with all conditions precedent, the only
obligation of Seller shall be that upon the return of the non-conforming equipment freight prepaid to Seller at its plant in Houston, Texas, Seller shall replace the defective or non-conforming parts, at no cost to Purchaser. In the
event of breach or repudiation of this agreement by Seller, or in the event any equipment sold hereunder fails to comply with any warranty extended herein, Seller shall not be liable to Purchaser or any third party for any
special, consequential, incidental or penal damages, including, but not limited to, loss of profit or revenues, loss of use of the products or any associated equipment, damages to associated equipment, costs of capital, cost of
substitute products, facilities, services or replacement power, down time costs, or claims of Purchaser’s or third party’s customers for such damages and PRUCHASER AGREES TO AND DOES HEREBY INDEMNIFY
SELLER FROM SUCH DAMAGES including but not limited to the consequences of sellers own negligence. If Purchaser transfers title to or leases the products sold to any third party, as a condition precedent to the
transference of the warranty to a third party, as set forth above, Purchaser shall obtain from such third party, a provision affording Seller and its suppliers the protection of the preceding sentence and PURCHASER
INDEMNIFIES SELLER FROM ANY LIABILITY OR ALLEGED LIABILITY TO ANY THUIRD PARTY, in the event Purchaser fails to comply with this condition precedent including but not limited to defense
costs, expenses and attorney fees. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. THERE ARE NO WARRANTIES, WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF. THIS LIMITED WARRANTY AND THE DAMAGES SET FORTH HEREIN ARE EXPRESSLY AGREED TO BE THE SOLE AND EXCLUSIVE REMEDY
AVAILABLE TO PURCHASER.
DELIVERY – Shipping dates are approximate and are based upon prompt receipt of all necessary information. Purchaser agrees that seller is not responsible for late deliveries for any reason, including but not limited to (1) causes
beyond Seller’s reasonable control or (2) acts of God, acts of Purchaser, acts of civil or military authority, priorities, fires, strikes, or other labor disturbances, flood, epidemics, war, or delays in transportation or car shortages or (3)
inability on account of causes beyond its reasonable control to obtain necessary labor materials, components or manufacturing facilities, (4) or any other delay. In the event of any such delay the date of delivery or of performance
shall be extend for a period to the time lost by reason of the delay.
PAYMENTS – Payments shall become due as specified in the terms, in the Quotation or Confirmation of Sale and Acknowledgment. In the event the terms are silent with respect to payment then payment shall be due thirty (30)
days from shipment to Purchaser by Seller, F.O.B. Seller’s plant, Houston, Texas. Purchaser agrees that no amounts will be deducted for late delivery. Any and all amounts due or to become due hereunder, shall bear interest at the
rate of ten percent (10%) per annum or at the maximum non-usurious rate, whichever is less, from date due as set forth herein until paid. If the financial condition of the Purchaser at any time does not, in the judgement of Seller,
justify continuance of the work performed by Seller hereunder on the terms of payment agreed upon. Seller may require full or partial payment in advance or shall be entitled to cancel any order than outstanding and shall receive
reimbursement for its reasonable and probably cancellation charges as set forth below in the Liquidate Damages paragraph in the event of bankruptcy or insolvency of the Purchaser, voluntarily or involuntarily, under the
bankruptcy or any insolvency laws. Seller shall be entitled to cancel any order then outstanding at any time during the period allowed for filing claims against the estate and shall receive reimbursement for its reasonable and proper
cancellation charges. The rights of the Seller under this paragraph are cumulative and in addition to all rights available to the Seller at law or in equity.
LIQUIDATED DAMAGES – Purchaser acknowledges that, in order to be able to fabricate and deliver the equipment in accordance with the Quotation and Confirmation of Sale and Acknowledgment, Seller must, and will be
purchasing the basic “hull” of the equipment, the cost of which represents a substantial part of the total cost of the equipment, for which there will be no reasonable market, in the event of the cancellation or attempted cancellation
of the contract or sale represented herein and that even with the exercise or reasonable efforts, Seller will not be able to “cover” its loss from a default or, cancellation of, this agreement by selling, or otherwise disposing of the
“hull” to other persons or entities. Purchaser further acknowledges that, in the event of a default or attempted cancellation, Seller will suffer immediate and substantial damages and losses, the exact amount and extent of which will
be difficult, if not impossible to measure with certainty or precision. Accordingly, and in order to provide a reasonable compensation and remedy to Seller, in the event of a default Seller, shall be entitled to recover, and Purchaser
hereby agrees to pay, liquidated damages as follows: (i) if Purchaser shall default in the performance of any of its obligations ninety (90) days or more prior to the estimated shipment date described herein, Purchaser shall pay to
Seller, liquidated damages equal to seventy percent (70%) of the purchase price; (ii) if damages equal to eighty percent (80%); (iii) if such default shall occur thirty (30) days or more, but less than sixty (60) days prior to the
estimated shipping date, Purchaser shall pay to the Seller, liquidated damages equal to ninety percent (90%) of the purchase price. Purchaser and Seller each agree that the foregoing liquidated damages constitutes a reasonable and
practical agreement for attempting to compensate Seller for the losses and damages it will suffer in the event of a default hereunder.
SALES AND SIMILAR TAXES – Seller’s prices do not include sales, use, excise or other similar taxes. Consequently, in addition to the price specified herein, the amount of any present or future sales, use, excise or other
similar tax applicable to the sale or use of the equipment hereunder shall be pain by the Purchaser, or in lieu thereof, the Purchaser shall provide Seller with a tax exempt certificate acceptable to the taxing authorities.
LIMITATIONS – Any action or proceeding relating to or concerning any Quotation, Purchase Order or Confirmation of Sale and Acknowledgment or any breach thereof must be commenced by Purchaser within two (2) years after
the asserted claim or cause of action shall have accrued (whether or not the party asserting such claim or cause of action had any knowledge or notice thereof, and, if not action or proceeding is commenced within such two (2) year
period, the purchaser shall be deemed to have waived all claims against Seller).
GENERAL – Any sale shall not be subject to arbitration. This agreement shall be construed in accordance with the laws of the State of Texas. All sales and warranties of goods or services will be F.O.B. Seller’s plant in
Houston, TX. All terms and conditions of sale, including all payments, are due, performable and payable in Houston, Harris County, Texas. All suits for the enforcement of any rights to either Seller or Purchaser as a result of
this agreement or any sale will be brought exclusively in a state court of competent jurisdiction in Harris County, Texas. This Contract supersedes all oral and written communications between Seller and Purchaser, including but
not limited to, any representations, agreements, understandings, order forms of Purchaser, orders of purchaser and their respective agents, whether issued before or after this Agreement. The provisions of this Contract cannot be
waived, changed, modified or terminated, except in writing signed by Seller. The invalidity, in whole or in part, of any of the foregoing provisions will not affect the remainder of such provisions. The purchaser warrants and
represents to Seller that if it is not a consumer and is a Merchant in the type of goods sold and that the goods or services represented by this sale are purchased for represents to Seller that it is not a consumer and is a Merchant in
the type of goods sold and that the goods and that the goods or services represented by this sale are purchased for commercial purposes. To the maximum extent allowed by law, Purchaser agrees to release and hold Seller
harmless and to indemnify Seller from all damages resulting from suits under the Texas Deceptive Trade Practices Act or other laws in so far as they include recovery for damages in excess of those allowed by this agreement
and the Uniform Commercial Code as adopted by the State of Texas, including but not limited to the consequences of Seller’s own negligence.
Replaced Parts on Repaired Equipment – In the event that during the repair process Seller replaces any parts on equipment owned or leased by Purchaser, the Purchaser agrees that the parts which have been replaced shall
become the property of Seller.

Form MM 6.002-1
Gulf Electroquip
G D M 8 5 0 - D R I L L M E C
Grasa
Use Grasa multi-proposito base Litio que cumpla con N.L.G.I. classification No.1 or No.2 en lo
siguiente:
No. of
Locacion Application Frequency
Fittings
Tubo Lavador 1 Al exceso Cada 12 horas
(Wash-Pipe)
Cilindros del Link Tilt 2 a 4 Bombazos por Semanal
(Link tilt cylinder) 2 conector
Collar de Carga 1 10 Bombazos por Semanal

(Load Collar) conector
Cilindro de la Al exceso Semanal
Mordaza 6
(Clamp cylinder)
Engrane de Giro 2 10 Bombazos por Semanal
(Slewing gear) conector
3 a 4 Bombazos por Cada 12 horas
IBOP 4 conector
Marco Extendidio 2 a 4 pumps por Semanal

20 conector
 Consultar el Diagrama de Mantenimiento en la pagina 3-2 por la locación de los puntos de engrase
Motor
Gulf Motor Consultar el Manual del Fabricante
Usar las recomendaciones del Fabricante
Motor Coupling ** Kop-Flex High Performance Gear Coupling Grease
Frequencia: 3-meses
Procedimiento para Engrase del Acoplamiento del Motor
• Remueva los 2 tapones instalados a los costados del acoplamiento

• Instale el conector para la grasa en un uno de los orificios
• Bombear grasa hasta que salga por el otro orificio
• Si la grasa esta sucia– siga bombeando hasta que salga grasa limpia
• Remueva el conector de la grasa e instale los 2 tapones

G D M 8 5 0 - D R I L L M E C
Top Drive Caja de Engranajes

GDM Top Drives están diseñados para trabajar con aceite de engranes ISO Industrial EP
(Extrema presión). Los aceites de extrema presión son de alta calidad, aceites de tipo compuesto
de presión extrema para usar en todo tipo de conjuntos de engranajes industriales, excepto aquellos
con mecanismo de transmisión de fricción de tipo de velocidad variable incorporado.
El uso de EP asegura una mayor vida útil de su GDM Top Drive, especialmente durante periodos
de fuerte martilleo. Los aceites EP brindan una protección superior contra la corrosión a las superficies
de metales ferrosos y no son corrosivos al acero, latón, bronce y otros materiales comunes en rodamientos.
Temperatura A.G.M.A Premium Top Drive Gear

Ambiente Number Oil
(°C)
25°C & Up1 EP 9005-E02 Chevron ISO Meropa 220
0-60°C EP 9005-E02 Chevron ISO Meropa 150
1 Contactar OEM por mas recomendaciones para otros rangos de temperatura
Productos similares están disponibles en USA por la corporación EXXON.

Los Aceites que cumplan con las especificaciones y grados de AGMA que se muestran en la tabla
anterior se pueden usar en estos GDM 850 Top Drive.
Para aprobación de aceite especifico, contacte el Departamento de ingenieria de

Premium.
El aceite debe de cambiarse a intervalos planificados de 90 days.
Nunca se debe permitir que el aceite se contamine visiblemente con lodo o agua, lo que rápidamente
causa fallas en los rodamientos. Si hay alguna duda de la calidad del aceite, debe cambiarse incluso si
no se debe realizar un cambio de acuerdo con el programa de mantenimiento.

GDM 850 - DRILLMEC
Top Drive Caja de Engranajes Capacidad de Aceite
The GDM 850 Top Drive Caja de Engranajes tiene una capacidad aproximada de 20 US Gallons.
Al operar un GDM 850 Top Drive en climas húmedos, o cuando se utilizan fluidos de perforación
corrosivos (e.g., alto contenido de salmuera), Asegúrese de que el aceite lubricante se revise semanalmente
para detectar contaminación con agua. Se deben tomar muestras para una confirmación visual.
La caja de engranaje puede ser drenada, removiendo el tapón en la parte inferior de la caja de engranes.
El tapón magnético está localizado en el filtro colador tipo Y para atrapar partículas pequeñas metálicas.
Una acumulación sustancial de tales partículas es a menudo una indicación de una falla inminente en
los rodamientos. Tambien hay una manguera que drena el aceite restante del rodamiento inferior.
Esto removerá cualquier contaminación del rodamiento.
Inspeccionar el respiradero (localizado en la parte del lado del perforador en el motor de tracción)
diariamente para asegurarse de que no esté tapado; reemplace el respiradero cuando sea necesario.
Se pueden producir daños en los sellos si se permite que se acumule presión en la caja de
engranajes.
Figura 9 – Filtro colador tipo Y
Figura 10 - Respiradero

G D M 8 5 0 - DRILLME C
Inspeccion
Las inspecciones recomendadas en esta sección deben tratarse como una guía del
fabricante y están basadas en las especificaciones de API 8B 8th Edition Mayo 2014
que dice:
“El usuario/propietario y fabricante deben desarrollar y actualizar conjuntamente la

inspección, mantenimiento, reparación y procedimientos de remanufactura consistentes
con la aplicación del equipo, carga, condiciones de trabajo, uso y condición operacional”
General
La inspección y el mantenimiento esán plenamente relacionados. Las acciones de
inspección y mantenimiento pueden basarse en, entre otros, o más de los siguientes:
- Limites de tiempo especificos
- Limites de desgastes medibles
- Acumulación de ciclo de carga
- No funcionamiento del equipo
- Ambiente
- Experiencias pasadas
- Requisitos reglamentarios
El objetivó de la inspección es detectar defectos de servicio o de fabricación ocultos,

así como posibles caídas de objetos. La existencia de grietas puede indicar un deterioro
severo y una falla inminente. Su detección, identificación y evaluación requieren métodos
de inspección precisos. Una vez detectados. Se necesita atención inmediata para retirar
el equipo del servicio y reemplazarlo o realizar el servicio o reparación apropiado antes
de seguir usando el equipo.
“Si se observa algún defecto de fabricación informar a Premium inmediatamente”
Nota:
Se debe tener precaución y tener en cuenta la mayor susceptibilidad a la fractura de

muchos aceros que operan a bajas temperaturas.

GDM 850 - DRILLMEC
Categorias De Inspeccion
Categoría I
Categoría II
Categoría III
Categoría IV
Estas categorías describen la tarea de inspección y el tipo de personal para cada categoría.
La necesidad de niveles específicos de entrenamiento aumentara a medida que aumenten
los niveles de categoría. La frecuencia de la inspección se detallará en la sección posterior.
Si se detecta una grieta, el área de inspección debe ampliarse y puede incluir áreas no señaladas
en las especificaciones de inspección y mantenimiento.
Categoria I
Esta categoría involucra la inspección visual del equipo por desempeño inadecuado
mientras está en servicio y se suma a la lista de verificación de mantenimiento.
Cuando se utiliza, el equipo debe inspeccionarse visualmente a diario para detectar los
siguientes:
- Grietas
- Ajustes sueltos o conexiones
- Alargamiento de piezas
- Signos de desgaste, corrosión o sobrecarga
- Dispositivos de bloqueo, sujetadores faltantes o inadecuados
- Pasadores faltantes o inadecuados en los grilletes
- Fugas de aceite hidráulico y de transmisión
- Desempeño inadecuado de cualquiera de las funciones
La inspección diaria deberá incluir inspecciones de posibles objectos caídos y dispositivos

de retención o cosas que puedan dañarse, que necesite ajuste o faltante.
Cualquier objecto potencial caído o perdido / los dispositivos de retención dañados deben
repararse inmediatamente.
La inspección debe ser realizada por personal con conocimiento del equipo y sus funciones
Si se detecta un problema, se necesita atención inmediata para retirar el equipo de servicio
o hacer las reparaciones necesarias.

G D M 8 5 0 - D R T I L L M E C
Categoria II
Estos son todos los artículos en la inspección Categoría I más una inspección adicional
para los siguientes:
- Corrosion
- Deformasion
- Componentes faltantes o sueltos
- Componentes deteriorados
- No lubricacion
- Fisuras externas visibles
- No ajustados correctamente
Esta es una inspección más minuciosa que Categoría I, por lo que se requiere un acceso
total al equipo.
La inspección debe ser realizada por personal con conocimiento del equipo y sus
funciones
Si se detecta un problema, se necesita atención inmediata para retirar el equipo de

servicio o hacer las reparaciones necesarias.
Categoria III
Estos son todos los artículos en la inspección Categoría II más una inspección
adicional, que debe incluir NDT de áreas críticas y puede implicar un desmontaje
parcial para acceder a ciertos componentes e identificar el desgaste que esta más allá
de las tolerancias de Premium.
Antes de la inspección, las partes que requieran NDT debe de tener la pintura en las
áreas de inspección ya sea química o mecánicamente eliminada.
La inspección debe ser realizada por personal con conocimiento del equipo y sus funciones.
Los requerimientos para el personal NDT están listados más abajo.
Category IV
Estos son todos los artículos en la inspección Categoría III más una inspección
adicional con suficiente desmontaje para permitir NDT a los componentes primarios
de carga.
El equipo sera:
- Desarmado en una instalación adecuadamente equipada para permitir NDT a
todos los componentes primarios de carga, así como a otros componentes
críticos del equipo.
- Inspeccione por desgaste excesivo, fisuras, defectos o deformaciones.

G D M 8 5 0 - D R I L L M E C
La inspección debe ser realizada por personal con conocimiento del equipo y sus
funciones. Los requerimientos para el personal NDT están listados más abajo.
Premium recomienda una revisión completa en este punto, para que todas las piezas
desgastadas como bujes, rodamientos, sellos, tornillería puedan ser remplazados.
Frecuencia de Inspeccion
Inspecciones Periodicas
Por API 8B, siete intervalos de tiempo diferentes para las inspecciones (consulte la hoja de
inspección adjunta que se encuentra más abajo) son de uso.
El usuario/propietario debe desarrollar programas de inspección basados en los

siguientes, experiencias pasadas, recomendaciones de Premium o por lo
siguiente:
- Ambiente
- Ciclo de carga
- Requisitos reglamentarios
- Tiempo de operacion
- Pruebas
- Reparaciones
- Remanufacturar
Como una alternativa, el propietario/usuario puede utilizar la Table 1 de recomendaciones
que están basados en API 8B . la planificación a largo plazo se puede ajustar para no
interferir innecesariamente con las operaciones de perforación.
Inspecciones No Periodicas (NPI)
Una inspección periódica equivalente a Categoría III o Categoría IV debe hacerse

antes (si sabe) y después (por ejemplo, martilleo, tubería de revestimiento muy
pesada, atrapamiento de tubería) y/ o después de operar a bajas temperaturas . Otros
factores podrían ser el almacenamiento a largo plazo o desalineación con el centro del
pozo.
NPI se anota en una columna separada en Tabla 2.

G D M 8 5 0 - D R I L L M E C
Tabla 1 para inspección y mantenimiento, categorías y frecuencias
Equipo Frequencia
Dias Meses Aňos
1 7 1 3 6 1 5
Top Drive I II III IV
Bloque viajero, gancho y bloque, block to hook I II III IV
adapter
Corona, poleas y rodamientos I II III IV
Conectores y adaptadores de enlace I II III IV
Notes:
Un aňo = 3,000 horas.
Cualquier parte de un dia operativo debe considerarse un dia.
NDT Personal Certificado
El inspector de NDT estará certificado de acuerdo a ISO 9712 o por otro reconocido
programa de certificación NDT.
Los inspectores deben conocer el tipo de equipo que se va a evaluar y los métodos de
NDT que se aplican.
El usuario/propietario verificara que el inspector NDT tenga la siguiente información:
a) Diagramas de ensamblaje y diagramas que identifiquen las áreas críticas a inspeccionar.
b) Criterio de rechazo
Nota:
En ausencia de diagramas que identifiquen las áreas críticas, toda el área de los
componentes de carga se considerara critica.
Estas áreas serán utilizadas por el inspector NDT para adaptar el procedimiento de inspección.

G D M 8 5 0 - D R I L L M E C
Criterio de Aceptacion
El criterio de Aceptación se basa en el Usuario/propietario y recomendaciones de Premium

El equipo desgastado que no cumpla con los criterios de aceptación no se aceptara para
el servicio.
Indicaciones superficiales
Indicaciones permisibles
Las indicaciones de superficie son indicaciones de tal tamaño, forma y ubicación que
no necesitan ser removidos.
Los siguientes son los límites de desgaste para los componentes de carga:
 La clasificación de carga nominal se mantiene si el desgaste es menor que 5%

para todos los componentes de carga del Top Drive, con la excepción del collar
de carga.
 La capacidad de carga nominal debe reducirse en 5% si el desgaste es entre 5% y

10% para todos los componentes de carga del Top Drive, con la excepción del
collar de carga
 El límite de desgaste para el collar de carga es 10% sin la necesidad de reducir la

capacidad de carga nominal. La capacidad de carga del collar de carga debe
reducirse en 5% si el desgaste es entre 10% y 15%.
Debe contactar a departamento de ingeneria de Premium s i e l d e s g a s t e e s m a
y o r a 10% para todos los componentes de carga, y mayor a 15% en el collar de
carga para obtener la capacidad de carga correcta.
Indicaciones no permitidas
Indicaciones no permitidas están clasificadas como:
a) Indicaciones menores en superficie:
i) Las indicaciones superficiales menores se pueden eliminar limando o esmerilando.

G D M 8 5 0 - D R I L L M E C
ii) Las picaduras de fondo Redondo y la erosión son aceptables siempre

que el defecto sea menor que 1/16 inch profundidad. Se debe tener
precaución para evitar el calentamiento mayor hasta tal punto que
podría cambiar las propiedades mecánicas del material.
b) Indicaciones mayores de superfice
i) Grandes defectos o cualquier indicación de grietas son motivo de
reemplazo del componente.
Componentes Rechazados
Componentes Rechazados deben ser marcados y removidos de servicio.
Inspeccion y Mantenimiento por Desalineación Del Top Drive Con El Centro Del Pozo
El eje principal del top drive está siendo sometido a la máxima tensión y cargas de
torsión a medida que los pozos se perforan a mayores profundidades y desviaciones.
La combinación de cargas de tracción y torsión puede alcanzar un alto porcentaje de
la resistencia del material. Cuando esto ocurre, solo se requiere una pequeña cantidad
de carga cíclica para reducir drásticamente la cantidad de ciclos antes de que ocurra
una falla por fatiga de material. Además cuando el top drive esta desalineado con la
sarta de perforación, durante la perforación en estas condiciones, la amplitud del
momento de flexión resultante que actúa sobre los componentes del conjunto del eje
impulsor principal puede crear un alto esfuerzo de inversión que provocara la falla
prematura de los componentes del Top Drive.
Visual y no-destructiva examinación (NDE) deberá realizarse en la conexión del eje
principal del top drives en periodos regulares recomendados API 8B and API 7-2.

G D M 8 5 0 - D R I L L M E C
Tabla 2: Hoja de Inspeccion

Cliente: Equipo : Inspeccionado por: Inspeccionado por: Fecha:
Marcar  si pasa, X si no pasa or N/A si no aplica.
Componentes Diagrama #’s
# Descripcion Frequencia:
Semana Mes Aňo NPI
1 7 1 3 6 1 5
1 Inspeccion visual general del equipo. I I
Nota: asegurarse de que todos los boletines de
seguridad de los productos hayan sido revisados
e implementados.
2 Inspeccion visual general del equipo II II

siguiendo Categoría II
3 Inspeccion del equipo siguiendo: IV
La guía Categoría IV
4 Inspeccionar el nivel de aceite de I I
lubricación
5 Inspeccionar la presión de aceite de I I
lubricación
6 Inspeccionar el indicador del filtro de I I
lubricación
7 Cambiar el aceite de lubricación y el II II
filtro, limpiar el Filtro colador tipo Y
8 Tomar muestras del aceite de II

lubricación.
Inspeccionar por ruidos inusuales I I
durante la operación.
Inspeccionar el tubo lavador por fugas I

Inspeccionar el top drive por fugas I I
hidráulicas o de lubricación.

G D M 8 5 0 - D R I L L M E C
Inspeccionar por lavado interno en III

línea de lodo, abajo del tubo, cuello de
ganso, adaptador del tubo y el eje
principal
Bail Adaptador II IV II
Block Interface II IV II
Block Interface Pernos II IV II
Caja de engranes y tapa II IV II
Platos de carga laterales II IV II
Pernos de carga II IV II
Collar de carga II IV II
Eje principal II IV II
Collar de aterrizaje II IV II
Retenedor del collar de aterrizaje II IV II
Inspeccionar el grosor de las paredes IV
del cuello de ganso y del eje principal.
Valvulas de control de lodo II II

Top drive guarda II II
Top drive armazon II II
Top drive accesorios montados II II
Inspeccionar el Top Drive por I I
componentes sueltos y cable de
seguridad rotos.
Inspeccionar el Top Drive por II II
componentes sueltos y cable de
seguridad rotos siguiendo
recomendaciones de Categoria II
Inspeccionar los cables electricos por II II
signos de deterioro o estiramiento.
Visualmente inspeccione la guia de I I

torque por danos o fisuras.
Visulmente inspeccione la guia de II II

torque usando la guia Categoria II

G D M 8 5 0 - D R I L L M E C
Visualmente inspeccione la guia de III

torque siguiendo la guía Categoria III si
se encuentran indicaciones de grietas
desde arriba.
Visualmente inspeccione la guía de IV
torque usando la guía Categoria IV
Inspeccione por tornillos flojos en I I
montaje del soplador, caja electrica en
el mastil, parrillas de cables y
mangueras hidraulicas.
Inspeccione por tornillos flojos en II II
montaje del soplador, caja electrica en
el mastil, parrillas de cables y
mangueras hidraulicas. Siguiendo la
guía Categoria II
Visualmente inspeccione los cables I I
electricos de servicio, los soportes del
loop de servicio en el Top Drive como
en el mastil.
II II
Visualmente inspeccione los cables
electricos de servicio, los soportes del
loop de servicio en el Top Drive como
en el mastil. Siguiendo la guía Categoria
II
Visualmente inspeccione el soplador y II II
las soldaduras de la base.
Inspeccione la pre-carga en los II II
rodamientos del eje principal y ajuste la
pre-carga si es nesesario. Instrucciones
en este manual.
Inspeccione la abertura entre el disco II II
del freno y las balatas del freno. El
disco del freno tiene que estar centrado
en las mordazas del freno.
Asegurarse que todos los cables de II II
seguridad estén instalados
correctamente.
Visualmente examine adentro de las II II
cajas electricas e inspeccione por
componentes sueltos.
Visualmente inspeccione todas las II II
soldaduras por fisuras.
Visualmente inspeccione la armadura II II
del motor electrico de perforación por
signos de caída.

G D M 8 5 0 - D R I L L M E C
Inspección Después De Periodos De Condiciones Severas De Perforación

Después de periodos de martilleo o perforación difíciles, especialmente cuando perforaran superficie,
algunos componentes del Top Drive pueden aflojarse o dañarse por la vibración excesiva.
El procedimiento siguiente es recomendado después de presentar martilleo o condiciones severas de
perforación:
 Visualmente examine el Top Drive por algún signo de daño externo
 Visualmente inspeccione la línea del lodo
 Visualmente Inspeccionar toda la tornillería y el cable de seguridad, si el cable de seguridad

está roto asegúrese que los tornillos estén apretados y coloque nuevo cable de seguridad.
“Asegúrese de apretar los tornillos a su torque recomendado”
 Inspeccionar todos los tornillos externos que no cuenten con cable de seguridad y asegurarse que estén
apretados.
 Inspeccionar todas las guardas, ventilaciones y tapas.
 Asegurarse todo cable de seguridad instalado correctamente
 Visualmente inspeccionar las todas las soldaduras que estén accesibles.
 Visualmente examine el interior de las cajas eléctricas por componentes flojos.
 Inspeccionar la armadura del motor eléctrico:
 Si el disco del freno esta aproximadamente en el centro de la mordaza del freno, es

una indicación que la armadura está bien.
 Si el disco del freno está tocando la parte de abajo de la mordaza del freno es una
indicación que los rodamientos del motor están dañados y la armadura se movió
hacia abajo.

Inspección y Ajuste de los rodamientos del Piñón GDM850
Después del ensamble verifique el espacio entre la tapa del rodamiento del piñon y la pista del rodamiento superior.
Apretar los tornillos e inspeccionar el movimiento vertical (endplay) del piñón. Nota: para ajustar el movimiento es
necesario agregar lainas de ajuste (shims) ajuste el movimiento vertical hasta que el movimiento sea 0.002” – 0.005” Pre-
Cargado.
EJEMPLO: Si después de armar y colocar el indicador de carátula para ver el movimiento vertical del piñón, se lee en el
indicador de caratula .005" se agregaría un máximo de .010" de lainas de ajuste (shims) para ajustar los rodamientos a .005”
Pre-Cargado.
Movimiento Inicial
Lainas agregadas
Movimiento Final Pre-Carga Estimada
Numero de Trabajo Fecha

Nombre Firma
Testigo
Inspección y Ajuste de Rodamientos del Eje Principal GDM850
• Armar el eje principal e instalar en la caja de engranes, apretar todos los tornillos a su respectivo torque.
• El peso del eje principal armado es de 4900 Lbs. aproximado
• Instalar la tapa superior del quill sin el O-Ring, empujela hacia abajo hasta que haga contacto con el rodamiento superior del eje principal.
• Mida el espacio entre la tapa y agrege .002” lainas(shims), esta sera la altura inicial de las lainas (shims). Instale las lainas de ajuste y la tapa
superior, apriete los tornillos de la tapa al torque recomendado.
• Instalar el indicador de caratula para leer el movimiento vertical del eje principal hacia arriba y hacia abajo.
• Instalar la tuerca de levante en la parte superior del eje principal y apriete la tuerca hasta que no tenga movimiento.
• Instalar un indicador de peso entre el gancho de la grúa y la tuerca de levante. Asegurarse que el indicador de peso este libre de
movimiento y este leyendo cero sin carga.
• Mueva el eje principal hacia arriba despacio hasta que el indicador de peso lea 9400 lbs. inspeccione el indicador de caratula y registre la
lectura, tiene que estar cerca de 0.002”. esta medida tiene que ser constante cada vez que se mueva el eje principal hacia arriba y el
indicador de caratula tiene que leer cero cuando se mueva hacia abajo.
• El movimiento registrado en el indicador de caratula mas 0.002” a 0.005” será la cantidad de lainas de ajuste(shims) que serán removidas
para ajustar los rodamientos del eje principal.
EJEMPLO:
Movimiento inicial 0.002”
Lainas(shims)a remover: 0.007”
Pre-Carga: -0.005”
• Remover el indicador de peso y la tuerca de levante.
• Remover la tapa superior, instalar el O-ring, Re-instalar la tapa con las lainas ajustadas y apretar los tornillos al torque recomendado.
Movimiento Inicial
Lainas removidas
Total de shims instaladas Pre-carga estímada con 4500 lbs
Numero de Trabajo Fecha
Nombre Firma
Testigo
2-52
G D M 8 5 0 - D R I L L M E C
Instrucciones De Inspección Del Tubo Lavador (Wash-Pipe)

Instrucciones
1. Coloque la base magnética del indicador de caratula en la parte de arriba del eje principal y en la tuerca
inferior del tubo lavador (wash-pipe)
2. Gire el eje principal 360° e inspeccione las lecturas del indicador (TIR) en las posiciones A, B, C.
 Desalineación máxima permitida en el cara plana del cuello de ganso = 0.008” B.
 Desalineación máxima permitida en la cara radial del cuello de ganso = 0.010” A
 Desalineación máxima permitida del tubo lavador después del montaje completo = 0.010” C
La inspección puede indicar una desalineación que exceda los limites recomendados
Los conjuntos de tubo lavador están diseñados para adaptarse a la desalineación que pudiera existir
entre el cuello de ganso y el eje principal y trabajara con una desalineación excesiva.
Sin embargo, para lograr la máxima vida útil de los empaques, la alineación en el tubo lavador debe
mantenerse dentro de los limites recomendados.

G D M 8 5 0 - D R I L L M E C
Inspeccion Freno De Disco Del Top Drive
Inspeccion De Mordazas Del Freno
 Las Mordazas del freno tienen que ser inspeccionadas semanalmente.
 Una prueba de funcionamiento, inspeccionar por fugas de aceite hidráulico.
 Por desgaste prematuro, Las Balatas del freno cuando se rozan el disco de frenado pueden
causar calor excesivo en el compartimiento del freno.
 Si las balatas del freno están rozando es probable que el Sistema hidráulico tenga aire
atrapado, para eliminar el aire atrapado es necesario purgar el sistema hidráulico.
Mirar el procedimiento de purgado del freno.

G D M 8 5 0 - D R I L L M E C
Listado de
Mantenimiento GDM 850 Listado de mantenimiento
fecha:
Cada 12 Horas Lun Mar Mie Jue Vie Sab Dom

Engrase del Tubo Lavador (washpipe)
Engrase Valvula de lodo remota (IBOP)
Nivel de aceite caja de enganajes
Realizado por:
Diario Lun Mar Mie Jue Vie Sab Dom
Engrase engrane de giro
Insp enfriador de aceite por obstrucciones
Engrase la mordaza de aguante
Insp el indicador del filtro hidraulico
Insp el indicador del filtro de Lubricacion
Insp repiradero de la caja de engranes
Insp el Top Drive por mangueras
hidraulicas sueltas o flojas.
Insp el Top Drive por tornilleria floja y
cable de seguridad faltante.
Engrase el mecanismo de extensión
Realizado por:
Semanal Lun Mar Mie Jue Vie Sab Dom
Engrase el Collar de Carga
Engrase la los pernos de la llave de
aguante
Engrase los pernos de los cilindros de los
brazos del elevador
Insp y limpieza de Y- colador de succión
de la bomba de lubricacion
Examine las balatas del freno & Mordazas
por desgaste y fugas
Realizado por:
Mensual Lun Mar Mie Jue Vie Sab Dom
Engrase Motor de Perforacion por
recomendación del fabricante
Remover & limpiar Boquillas aspersores
de lubricación cada cambio de aceite
By:
Cada 3 Meses Lun Mar Mie Jue Vie Sab Dom
** Engrase el acoplamiento del Motor
Cambio de aceite de lubricación en caja de
transmisión
Próximo cambio de aceite:

8 7 6 5 4 3 2 1
D D
PRECEDURE:
PERFORM DRY MAGNETIC PARTICLE INSPECTION

100% OF ALL SURFACES AND WELDS IN
ACCORDANCE WITH ASTM E709.
PERFORM WET FLUORESCENT MAGNETIC PARTICLE

INSPECTION ON ALL AREAS INDICATED.
ACCEPTANCE CRITERIA PER API SPEC 8C PSL 2

C C
ALL AREAS TO BE VISUALLY INSPECTED FOR DAMAGE
AND SIGNS OF FATIGUE.
THE FOLLOWING INFORMATION SHOULD BE SUPPLIED

ON THE INSPECTION REPORT AT A MINIMUM:
• DATE
• PURCHASE ORDER #
• INSPECTION REPORT #
• GDS/PREMIUM PART #
• LOAD RATING
B • SERIAL # B
• TYPE OF INSPECTION
• SPECIFICATION AND ACCEPTANCE CRITERIA
• INSPECTOR'S SIGNITURE
• GDS/PREMIUM REPRESENTATIVE
UNLESS OTHERWISE SPECIFIED: NAME DATE

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DS 16AUG2022 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED LL 16AUG2022 TITLE:
A
ANGULAR: MACH .5 BEND 1
ONE PLACE DECIMAL .031 APPR. - -
LANDING A
TWO PLACE DECIMAL .015
THREE PLACE DECIMAL .005
COLLAR
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION
PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5M
THE INFORMATION CONTAINED IN THIS MATERIAL
SIZE PART/DWG NO. REV
B M800019
DRAWING IS THE SOLE PROPERTY OF -
1
GLOBAL DRILLING SUPPORT INTL. ANY
FINISH
REPRODUCTION IN PART OR AS A WHOLE
125 Ra UNLESS NOTED OTHERWISE
WITHOUT THE WRITTEN PERMISSION OF
GLOBAL DRILLING SUPPORT INTL. IS
PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 102.82 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D WET FLUORESCENT MPI PRECEDURE:

D
ALL SURFACES I.D.

WET FLUORESCENT MPI
RADIUS SURFACE X 2 PERFORM WET FLUORESCENT MAGNETIC PARTICLE

C C

• DATE
• LOAD RATING
• SERIAL #
WET FLUORESCENT MPI • TYPE OF INSPECTION
B MACHINED SURFACES B
ON BOTTOM • INSPECTOR'S SIGNITURE

PREMIUM
TOLERANCES:
A
LINKS LOAD A
COLLAR
THIRD ANGLE
B M800021
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
PRECEDURE:



C ALL AREAS TO BE VISUALLY INSPECTED FOR DAMAGE C

• DATE
• LOAD RATING
• SERIAL #
B • TYPE OF INSPECTION B

PREMIUM
TOLERANCES:
A
PIN, LOAD A
THIRD ANGLE
B M800125
1
FINISH
PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 58.11 LBS LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
PRECEDURE:



C
ALL AREAS TO BE VISUALLY INSPECTED FOR DAMAGE C

• DATE
• LOAD RATING
B • SERIAL # B

PREMIUM
TOLERANCES:
A
QUILL, 750T A
MACHINING
THIRD ANGLE
B M800338
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D PRECEDURE: D



C C
WET FLUORESCENT MPI AND SIGNS OF FATIGUE.

THRUST BEARING SURFACE
BORE
• DATE
• LOAD RATING
• SERIAL #
B • SPECIFICATION AND ACCEPTANCE CRITERIA B

PREMIUM
TOLERANCES:
A WET FLUORESCENT MPI
GEAR BOX A
PIN HOLES X 4 TWO PLACE DECIMAL .015
MACHINING
THIRD ANGLE
B M800343
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
PRECEDURE:



C ALL AREAS TO BE VISUALLY INSPECTED FOR DAMAGE C

WET FLUORESCENT MPI
RADIUS SURFACES
• DATE
• LOAD RATING
• SERIAL #
B • TYPE OF INSPECTION B

PREMIUM
TOLERANCES:
WET FLUORESCENT MPI FRACTIONAL 1/16 CHECKED LL 16AUG2022 TITLE:
A PIN HOLES ONE PLACE DECIMAL .031 APPR. - - BEAM A
THIRD ANGLE
B M800356
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
WET FLUORESCENT MPI

ENTIRE SLOTS
D D
PRECEDURE:



C C

• DATE
• LOAD RATING
B • SERIAL # B

PREMIUM
TOLERANCES:
TITLE:
WET FLUORESCENT MPI FRACTIONAL 1/16 CHECKED LL 16AUG2022
A PIN HOLES
SIDE LOAD A
PLATE
THIRD ANGLE
B M800357
1
FINISH
8 7 6 5 4 3 2 1
Load Path Component and Data
LOAD PATH PART NUMBER SERIAL NUMBER
COMPONENT
EQUIPMENT OEM S/N A801000 54
GEAR BOX LID M800345 407486-A801001-1-1
GEARBOX M800344 407486-A801001-1-1
MAIN SHAFT M800338 405655-M800338-1-1
LANDING COLLAR M800019 BAT51545-M800019-1-3
LINK COLLAR M800021 51328-M800021-1-4
BULL GEAR M800327 407996-M800327-1-1
PINION GEAR M800326 407996-M800326-2-2
BEAM M800356 408055-M800356-1-1
SIDE PLATE ODS M800357 408055-M800357-2-1
SIDE PLATE DS M800357 408055-M800357-2-2
SIDE PLATE PIN M800125 407570-M800125-2-04
SIDE PLATE PIN M800125 407570-M800125-2-08
SIDE PLATE PIN M800125 407570-M800125-2-02
SIDE PLATE PIN M800125 407570-M800125-2-10
1200HP A/C MOTOR E107925 2201594
IBOP VALVE R800007 M22-2476-1
GOOSENECK M800540 407711-M800540
THRUST BEARING M100044 216278259.0098
SAVER SUB 1 M800376 409192-M800376-1
SAVER SUB 2 M800376 409192-M800376-2
2-63
GDM 850 - DRILLMEC
3
Section
Drawings and Parts

Contents
Assembly Drawings 3-2
Index
Assembly Drawings 3-5
Electrical Schematics 3-69
Hydraulic Schematics 3-81
Itemized Spare Parts
3-86
GDM 850- DRILLMEC REV. 10 Page 3-1

GDM 850 - DRILLMEC
3 – Assembly Drawings
Assembly Drawing Index
Drawing No. Rev. Description
A801000 01 TOP DRIVE 750TON AC
A801002 01 GEAR BOX AND GEAR ASSY
A500031 01 LINK TILT CYLINDER DISRIBUTION
A500017 01 HYDRAULIC RETURN MANIFOLD
A800047 01 QUILL ASSY
A801001 02 GEAR BOX
A800042 01 LINK TILT MANIFOLD
A800136 01 SMALL SIGHT GLASS
A800050 01 LUBE FILTER
A800049 01 HYDRAULIC FILTER
A800381 03 SERVICE LOOP MOUNT
A800368 01 LINK ASSY
A800045 01 ROTATE ASSY
A800367 02 LINK COLLAR ASSY
A800271 01 ANTI ROTATION ASSY
A800383 01 WEIGHT SENSOR
A800372 01 TILT PLATE
A100246 01 LINK TILT CYL ASSY
A800353 02 BAIL CLAMP ASSY
A800056 01 ROD STOP ASSY
A800369 01 BLOCK INTERFACE ASSY
A800370 02 SERVICE PLATE ASSY

GDM 850 - DRILLMEC
A801003 01 HYDRAULIC VALVE BANK
A800270 01 ANTI ROTATION
A800346 01 BRAKE ARM ASSY
A800361 01 PIPE HANDLER MOTOR ASSY
A500245-480 01 LUBE PUMP ASSY (480v)
A800371 02 BONNET ASSY
A103104 03 TORQUE ARRESTOR ASSY
A103103 02 CLAMP CYLINDER ASSY
A103102 01 GRABBER W/PISTON ASSY
A100110 01 DIE BLOCK/JAW
M800376 01 SAVER SUB
A800048 01 IBOP
A800349 01 VALVE CLAMP ASSY
A800373 01 MOTOR ASSY
A500231 02 BRAKE ASSY
A500255 01 SEAL HOUSING ASSY
A500016 01 BRAKE DUMP VALVE
A800036 01 MOTOR HUB ASSY
A500163 01 HYD LUBE BRAKE MANIFOLD ASSY
A800385 01 OIL FILL GEAR BOX
GDM 850 - DRILLMEC REV. 10 Page 3-3

GDM 850 - DRILLMEC

A800348 01 AUXILLARY J-BOX
A800379 02 LUBE COOLER ASSY
A500627-1 01 PLC J-BOX
A800375 01 ELEVATOR OPEN CLOSE ASSY
A800377 01 ELEVATOR FLOAT ASSY
A500407-DM 01 TOPDRIVE CABLE KIT
M800540 02 MUD LINE
A500012 01 LABEL KIT
A800046 02 EXTEND FRAME
A800051 02 FRAME BASE
A800052 02 FRAME MOUNT
A800055 01 ROD STOP ASSY
A500684 02 ELECTRICAL KIT
A800141 01 EXTEND FRAME VALVE ASSY
A100248 01 ORIFICE 1/8"
A800054 02 COUNER BALANCE VALVE
A101899 02 LIMIT SWITCH ASSY

8 7 6 5 4 3 2 1
ITEM NO. PART NUMBER DESCRIPTION QTY. ITEM NO. PART NUMBER DESCRIPTION QTY.
1 A500031 LINK TILT CYLINDER DISTRIBUTION 1 34 S101568 SEAL 2
BLOCK ASSEMBLY
ASSEMBLY, QUILL, GDM750, 3 INCH 35 S500004 O-RING, 13.5 X 14.0 X .250, N-70 1
2 A800047 BORE 1
36 S500014 O-RING, 2.406 ID x .139 4
3 A800136 ASSY, SIGHT COVER, SMALL 2 THERMOWELL 850 GEARBOX, 1/2
37 N100659 NPT x 3/4 NPT 1
D
4 A500017 GDM HYDRAULIC RETURN 1
D
MANIFOLD 38 H101001 ADAPTER, MALE 1/2 ORFS, MALE 1/2 1
5 A800382 ASSMEBLY, PINION, 17T 1 ORB
ASSEMBLY, GEARBOX, FINAL 39 H101003 ADAPTER, MALE 1/2 ORFS, MALE 3/4 1
6 A801001 MACHINING, GDM750 1 ORB
BEARING, CYLINDRICAL ROLLER, 40 026211.1264DH2 CAPSCREW,SOCKET HEAD, 3/4- 12
7 M102890 260x400x65 1 10UNC X 4.00, DH2
GEARFLEX A SERIES DBL. 41 008121.0616DH2 CAPSCREW, HEXHEAD, 3/8-16 X 1" 8
8 M102894 ENGAGEMENT TYPE DA COUPLING 1 GR. 8
42 008121.1232DH2 CAPSCREW,HEX HEAD, 3/4-10UNC X 1
9 M500255 FLANGE BOTTOM QUILL 1 2.00,DH2
10 M500256 SEAL, CAGE, TOP 1 43 008121.1236DH2 CAPSCREW,HEX HEAD, 3/4-10UNC X 12
2.25,DH2
11 M500260 COVER FLANGE BOTTOM PINION 1 CAPSCREW,HEX HEAD, 7/8-9UNC X
44 008121.1440DH2 2.50,DH2 12
12 M500262-050 SHIMS, SET, PINION .050 4
45 220102.0600 WASHER,LOCK,NORDLOCK,1 PAIR 8
C 13 M500262-020 SHIMS, SET, PINION .020 2 3/8 C
14 M500262-010 SHIMS, SET, PINION .010 2 46 220102.1200 WASHER, LOCK, NORDLOCK, 1 PAIR, 13
3/4"
15 M500262-005 SHIMS, SET, PINION .005 2 WASHER,LOCK,NORDLOCK,1 PAIR
47 220102.1400 7/8 12
16 M500262-003 SHIMS, SET, PINION .003 3
48 220102.1000 WASHER, LOCK, NORDLOCK, 1 PAIR, 12
17 M500281 SLEEVE SEAL, QUILL, LOWER 1 5/8
18 M500498 FLANGE, SUCTION DRAIN, GDM 500 2 49 230101.1200 WASHER, LOCK, HI COLLAR 3/4" 12
19 M800035 FLANGE TOP QUILL 1 50 312221.0610 SETSCREW, 3/8-24 UNF X 0.63 CUP 6
POINT
20 M800037 FLANGE TOP PINION 1 CAPSCREW,HEX HEAD, 5/8-18UNF X
51 008122.1028DH2 1.75,DH2 12
21 M800038 FLANGE BOTTOM PINION 1
22 M800046 LUBE NOZZLE 2 52 230101.0800 WASHER,LOCK,HI COLLAR 1/2'' 8
53 026211.0820DH2 CAPSCREW,SOCKET HEAD, 1/2- 8
23 M800054 RETAINER 1 13UNC X 1.25, DH2
B B
24 M800146 HUB, MACHINING 1 54 H102696 ELL 90, MALE 1 1/4 JIC x MALE 1 1/4 2
ORB
25 M800051 FLANGE, FILLER CAP 2 ADAPTER, MALE 3/8 ORFS, MALE 3/8
O-RING, 1 1/4 x 1 1/2 x 1/8 (USE ON 55 H500012 ORB 1
26 S100056 M800046) 2
56 H100999 ADAPTER, MALE 3/8 ORFS, MALE 1/2 2
27 S100079 O-RING, 8 3/4 x 9 x 1/8, NITRILE 2 ORB
O-RING,2-224,NITRILE, N70, 1.75 X 57 H500075 ADAPTER, MALE 3/8 ORFS, MALE 5/8 1
28 S100419 2.00 X 1/8 2 ORB
29 S100123 O-RING, 10 1/2 x 11 x 1/4 1 58 H100389 VALVE, HYD, RELIEF, 250 PSI, 1/2 NPT 1
30 S100129 O-RING, 15 x 15 1/2 x 1/4 1
31 S101530 O RING, 6 1/4 X 6 1/2 X 1/8, 2- 259, 1
70 DUROMETER UNLESS OTHERWISE SPECIFIED: NAME DATE
PREMIUM
32 S101566 SEAL, OIL SEAL 8.5 X 10 X .625 2 DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN JP 6/20/2022 DRILLING EQUIPMENT AND SUPPORT
CHECKED TITLE:
33 S101567 SEAL, OIL SEAL 10.5 X 12.5 X .625 2 FRACTIONAL 1/16 DS 6/21/2022
A
ONE PLACE DECIMAL .031 APPR. - - ASSEMBLY, GEARBOX A
PROPRIETARY AND CONFIDENTIAL

THREE PLACE DECIMAL .005 GDM 750 TON
THIRD ANGLE
This drawing contains confidential and
proprietary information of
INTERPRET GEOMETRIC
TOLERANCING PER: ASME Y14.5M
PROJECTION -
Premium Oilfield Technologies. MATERIAL
Neither this document nor any information SIZE PART/DWG NO. REV
B A801002
disclosed herein shall be reproduced
1 RELEASE FOR ASSEMBLY 6/21/2022 JP

in any form, used, or disclosed to
others for any purpose, including
manufacturing without the express
FINISH
125AA UNLESS STATED OTHERWISE 1
written permission of:
REV. DESCRIPTION DATE APPROVED ECN # Premium Oilfield Technologies®
DO NOT SCALE DRAWING WEIGHT: LBS SHEET 1 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
2
58 57
25
8
6 D
D
19 23
20 55
25
22
6
56
6
A
22
C C
51 48 58 40
24
3 6
51
21 43
B B
4
11
44
44
2
PREMIUM
DRILLING EQUIPMENT AND SUPPORT
TITLE:
A ASSEMBLY, GEARBOX A
GDM 750 TON
-
A B A801002 1
WEIGHT: LBS SHEET 2 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D 5 D
E
7
5
43
D
44
41
C 9
17 2 33 11
C C
DETAIL B
B 2 2 2 DETAIL C
SCALE 1 : 8
19
34 8 24 5 42 23 5
40 2
48 51
B B
20
5
SECTION A-A
SCALE 1 : 20 DETAIL D
SCALE 1 : 8 DETAILNAME
E DATE
GDS International
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES DRAWN JP 6/20/2022
TOLERANCES:
FRACTIONAL 1/16 CHECKED DS 6/21/2022 TITLE:
A
ASSEMBLY, GEARBOX A
TWO PLACE DECIMAL .015 GDM 750 TON
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION -
A801002
DRAWING IS THE SOLE PROPERTY OF
FINISH
125AA UNLESS STATED OTHERWISE B 1
PROHIBITED. DO NOT SCALE DRAWING WEIGHT: LBS SHEET 3 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ITEM NO. PART NUMBER DESCRIPTION QTY.

1 M500670 MANIFOLD BRACKET 1
11 13 1 13 13
2 H500042 MANIFOLD, 6 PORT 2
3 H101970 ELL90º, MALE 3/8" ORFS, 3/4" ORB 2
D
D
4 H500081 ADAPTER, MALE 3/8" ORFS, MALE 2
2 3/4"
ORB
6 H500021 ELL90º, MALE 3/8" ORFS, MALE 1/2" 2
ORB
7 220102.0400 WASHER, LOCK, NORDLOCK, 1 PAIR 8
1/4
8 91251A554 CAPSCREW, SOCKET HEAD, 1/4- 8
8 10 20UNC X 3.00,DH
9 101112.0400 1/4"-20 UNC, HEX NUT, STOVER C 8
3
10 208201.0400 WASHER, FLAT, 3/8, NARROW 8
C 11 H101400 PLUG, SOCKET HEX, 1/2'' ORB 4 C

11 11 4 3/8
13 008121.0614DH CAPSCREW,HEX HEAD, 3/8-16 X 3
7/8'', GR8
12 13
8 10 1
3 4 2
B B
2

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DRILLING EQUIPMENT AND SUPPORT
6 5 3 9 7 2 5 6 TOLERANCES:
JP 5/20/2022
FRACTIONAL 1/16 CHECKED - - TITLE:

A
ONE PLACE DECIMAL .031 APPR. - - LINK TILT CYLINDER A

THREE PLACE DECIMAL .005 DISTRIBUTION
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION BLOCK ASSEMBLY
B A500031
1 RELEASE FOR MANUFACTURING 5/20/2022 JP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 M800338 QUILL 850T, MACHINING, 3 INCH 1

BORE
2 M100044 BRG, TPRD ROL, THRUST 1
3 M102892 LOCKING ASSEMBLY 1 D
D
A A 4 M800327 GEAR, 126T, 10MM, 15 DEG HELIX 1
5 M102887 BEARING, TAPERED ROLLER 1
6 M800058 SLEEVE, SEAL, QUILL, UPPER, 1

GDM850
7 M800377 SPACER, QUILL, GDM750 1
8 M800019 LANDING COLLAR, 850T 1
9 M800020 RETAINER, RING LOAD 1
NOTES: 10 M101170 SPIRAL RETAINING RING, 2 TURN 1
1. LOWER BEARING AND LOWER SEAL SLEEVE SHOWN ON A801002.
2. TORQUE BOLTS ON ITEM 3 (LOCKING RING) IN A STAR PATTERN USING 11 R100364 LINER, UPPER STEM 1
C 3 STEP TORQUE INCREASE METHOD TO 508 FT/LBS EA. SEAL, POLYPAK TYPE B, POLYMYTE, C
12 S100487 3.875 STD BORE 1
13 M800361 SLEEVE, SEAL, QUILL, UPPER, 1

GDM850
14 M800362 MUD SHIELD, POLYETHYLENE, GDM 1
850T
4 3 1
11
3
D
C E
3.0
B FLUID BORE B
B
4
7 5/8 REG
14

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN JP 3/28/2022 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED D2 6/15/2022 TITLE:
A SECTION A-A ANGULAR: MACH .5 BEND 1
APPR. ASSEMBLY, QUILL A
SCALE 1 : 16 ONE PLACE DECIMAL .031 - -

THREE PLACE DECIMAL .005 GDM 750 TON
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION 3 INCH BORE
B A800047
1 RELEASE DRAWING FOR MANUFACTURING 6/15/2022 JP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
11 14 13 6 1
11 12
5
D F D
DETAIL B
C C
SCALE 1 : 4 DETAIL C
DETAIL F SCALE 1 : 8
SCALE 1 : 2 DETAIL G
1 2 7 SCALE 1 : 4
1 8 9 10
H INTERFERENCE FIT
BETWEEN RACE OF THRUST
BEARING AND QUILL.
B B
DETAIL E
SCALE 1 : 8
PREMIUM
7 TITLE:
A ASSEMBLY, QUILL A
2
GDM 750 TON
3 INCH BORE
DETAIL D
SCALE 1 : 8 DETAIL H SIZE PART/DWG NO. REV
SCALE 1 : 4
B A800047 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800136 SIGHT COVER, SMALL, FRAME, GDM850 1
2 M800137 SIGHT COVER, SMALL, GASKET, GDM850 1
3 M800138 SIGHT COVER, SMALL, LENS, GDM850 1
4 008121.0620DH2 CAPSCREW,HEX HEAD,3/8-16UNC X 1.25,DH2 8
D
5 206101.0600 WASHER,FLAT,HARDENED,F436 PLAIN, 3/8 8 D
6 M100559 WIRE ROPE, 1/16" SS, 7X7 SAFETY CABLE 4'
7 M100482 FERRULE, 1/16", OVAL, ALUMINUM 4
C C
6.25
5
B B
10.75
GDS International
DIMENSIONS ARE IN INCHES DRAWN DF 8/11/2014
ASSY, SIGHT
TOLERANCES:
FRACTIONAL 1/16 CHECKED DGW 8/11/14 TITLE:
COVER, SMALL
A ONE PLACE DECIMAL .031 ENG APPR. XX
A
XX/XX/XX
THREE PLACE DECIMAL .005 MFG APPR. XX XX/XX/XX
PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC Q.A.
TOLERANCING PER: ASME Y14.5M XX XX/XX/XX
THE INFORMATION CONTAINED IN THIS
MATERIAL
DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV
B
AS NOTED
A800136
01 RELEASE FOR MANUFACTURE DF 8/11/14

GDS PART No.-Revision FINISH
01
REV. DESCRIPTION INITIAL DATE
PROHIBITED. A800136-01 DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: 1.08 SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

2 H101400 PLUG, SOCKET HEX, 1/2'' ORB 2
3 H101001 ADAPTER, MALE 1/2 ORFS, MALE 1/2 ORB 2
D 5 H100844 ADAPTER, MALE 1/2 JIC, FEM SWV 1/2 ORFS 1 D
6 H100199 VLV, HYD, RELIEF, 90, SAE-8 1

7 H101027 ELL 90, MALE 1/2 ORFS X MALE 1/2 ORB, S 1
8 026211.01040DH2 CAPSCREW, HEX SOC HD, #10-24UNC x 2.50 4
4 1 3 2 9 8 4 DRILLED
9 230101.01000 WASHER,LOCK, #10 4
10 M100559 WIRE ROPE 1/16 SS, 7X7 SAFETY CABLE 1
11 M100482 1/16 ALUMINUM OVAL, WIRE ROPE CLIP 4
2
3
C C
4
1 2 3 5
5 6
5
B B
7 6
7
7
NAME DATE
GDS International
DIMENSIONS ARE IN INCHES DRAWN DGW 05/19/2014
TOLERANCES:
FRACTIONAL 1/16 CHECKED WJB 11/14/2014 TITLE:
A A
ONE PLACE DECIMAL .031
APPR. WJB 11/14/2014 GDM HYDRAULIC
THIRD ANGLE RETURN MANIFOLD
SEE BOM SIZE PART/DWG NO. REV
A500017
1 RELEASED FOR MANUFACTURE 05/09/2014 DGW

FINISH
REV. DESCRIPTION DATE APPROVED ECN # PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 6.44 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
2 1 M800343 MACHINING, GEARBOX, GDM750 1

2 M800345 GEAR BOX LID 850T, MACHINING 1
3 M100967 DOWEL PIN, 1/2'' x 2'' LONG 3
D D
1 4 220102.1400 WASHER,LOCK,NORDLOCK,1 PAIR 39
7/8
5 026211.1444DH2 CAPSCREW SOCKET HEAD 7/8-9 39
UNC X 2-3/4" DH2
4 5 3
C C
3
3
67.00
+.0050
28.6130 - .0000
B B
38.25

PREMIUM
59.00 DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN JP 5/12/2022 DRILLING EQUIPMENT AND SUPPORT
A
ONE PLACE DECIMAL .031 APPR. - - ASSEMBLY, GEARBOX A

THREE PLACE DECIMAL .005 FINAL MACHINING
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION GDM
B A801001
2 CHANGED LOWER MAIN BEARING BORE DEPTH AND ADDED CHAMFER DETAIL, PAGE 2 7/21/2022 JP disclosed herein shall be reproduced
1 RELEASE FOR PRODUCTION 5/12/2022 JP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 H102956 ASSEMBLY, PRESSURE FILTER 1
2 H102971 ELEMENT, HI PRESSURE FILTER 1
3 S100484 WPF4 BOWL O-RING 1
D D
4 M101201 WPF4 ANTI-EXTRUSION RING 1
C C
1 3 4 2 1 1
B B
GDS International

TOLERANCES:
NOTE: FRACTIONAL 1/16 CHECKED DGW 3/24/15 TITLE:
A
ONE PLACE DECIMAL .031 APPR. DF 3/24/15 ASSEMBLY, A
1. ITEM NUMBER 1 IS A REUSABLE CORES TWO PLACE DECIMAL .015
THREE PLACE DECIMAL .005 PRESSURE FILTER
THIRD ANGLE
B H102956
01
FINISH
01 RELEASE FOR MANUFACTURE 3/24/2015 DF 125AA UNLESS STATED OTHERWISE
REV. DESCRIPTION DATE APPROVED ECN # PROHIBITED. DO NOT SCALE DRAWING WEIGHT: LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800317 BRACKET, PRESSURE FILTER, GDM 1
1 5 850
3 2 H102956 ASSEMBLY, PRESSURE FILTER 1
6 3 H102974 FLANGE ADAPTER, 1" CODE 62, 2
D W/#16 SAE D
4 S101800 O-RING, N90-219, 1.296ID x 0.139 3

DIA
5 H102975 MANIFOLD, 1" CODE 62 PORT 1
7 ADAPTER, MALE 3/4 ORFS, MALE 1
6 H101008 ORB, S 1
7 H101035 ELL 90, MALE 3/4 ORFS, MALE 1 ORB 1
9 11 2 9 10
A ORB
9 230101.0800 WASHER,LOCK,HI COLLAR 1/2'' 8
10 011215.1285DH2 SOCKETHEAD CAPSCREW, M12-1.75 4
15 14 14 15 x 85MM, GR 12.9 BLACK
C
11 011215.1245DH2 SOCKETHEAD CAPSCREW, M12-1.75 4 C
8 x 45MM, GR 12.9 BLACK
1 12 220102.0600 WASHER,LOCK,NORDLOCK,1 PAIR 4
3/8
12 13 CAPSCREW, HEX HEAD, FULL
3 13 017141.1020DH2 THREAD, METRIC, M10 X 1.25 X 30 4
13 12 MM
8 1/2
7 6 CAPSCREW, HEX HEAD, 1/2-13UNC
15 008121.0824DH2 X 1.50, DH2 2
16
16 H100656 PLUG, SOCKET HEX, 1/4 ORB 3
9 10 10
B B
9 11 16
6 5 NOTES:
3 5 WHEN CHANGING PRESURE FILTER ELEMENT, RETAIN METAL SCREEN.
REPLACEMENT ELEMENT P/N H102971
2 3

PREMIUM
TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. - - ASSEMBLY A
HYDRAULIC
A PROPRIETARY AND CONFIDENTIAL THREE PLACE DECIMAL .005
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION PRESSURE FILTER
B A800049

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
14 15 2 12 13
4 4 4
6
1 7
12 13
C 11 C
3
3
5 3
16
B B
2
SECTION A-A
SCALE 1 : 4
PREMIUM
TITLE:
A ASSEMBLY A
HYDRAULIC
PRESSURE FILTER
B A800049 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800537 TOP DRIVE CONNECTION MOUNT 1
2 M500623 CLAMP PLATE, SERVICE LOOP HANGER - GUARD 1
ALL PLUGS ARE INCLUDED 3 M800531 CLAMP PLATE, SERVICE LOOP HANGER - GUARD 1
IN SEPARATE PIGTAIL
TERMINIATION KIT 4 H102505 NIPPLE, MALE PIPE, HEX, 1 MNPT, 3/4 MNPT 1
D D
5 H100732 NIPPLE, MALE PIPE,HEX 3/8 NPT 2
6 H100736 NIPPLE, MALE PIPE, HEX, 3/4 NPT 1
7 H100737 NIPPLE, MALE PIPE, HEX, 1 NPT 1
1
8 H100804 TEE, MALE RUN, FEM, 1 NPT 1
9 H100838 ADAPTER, MALE 3/4 ORFS, MALE 3/4 NPT 2
10 H107028 PH CHECK VALVE 3/4"NPT 5 PSI CRACKING PSI 1
11 H500025 PLUG, DUST, CAP, HYD, 3/4, VEP NPT, STUCCHI, FEMALE 1
12 H500026 NIPPLE, HYD, 3/4, VEP NPT, STUCCHI, MALE 1
27 29
13 H500027 CAP, DUST, HYD, 3/4, VEP NPT, STUCCHI, MALE 1
C
15 H500055 NIPPLE, HYD, 3/8, VEP NPT, STUCCHI, MALE 1
C
16 H500054 CPLG, HYD, 3/8, VEP NPT, STUCCHI, FEMALE 1
17 H500056 CAP, DUST, HYD, 3/8, VEP NPT, STUCCHI, MALE 1
27 30 18 H500067 CPLG, HYD, 3/4, VEP NPT, STUCCHI, FEMALE 1
19 H500066 PLUG, DUST, HYD, 3/8, VEP NPT, STUCCHI, FEMALE 1
20 H500101 VALVE, CHECK, INLINE, 3/8NPTF, 1PSI CP 1
21 H500162 NIPPLE, HYD, 1", VEP NPT, STUCCHI, MALE 1
31 28 22 H500162-1 CAP, DUST, HYD, 1", VEP NPT, STUCCHI, MALE 1
23 H500163 CPLG, HYD, 1, VEP NPT, STUCCHI, FEMALE 1
24 H500163-1 PLUG, DUST, HYD, 1", VEP NPT, STUCCHI, FEMALE 1
25 M100460 SHACKLE, ANCHOR BOLT TYPE, 7/16, GALV 3
B 26 008121.0832DH2 CAPSCREW, HEX HEAD, 1/2-13UNC X 1.75, DH2 GR8 1 B
25 2 27 008121.1036DH2 CAPSCREW,HEX HEAD, 5/8-11UNC X 2.25,GR8,DH2 8
28 026211.1696DH2 CAPSCREW,SOCKET HEAD, 1-8UNC X 6.00, DH2 3
29 220102.0800 WASHER,LOCK,NORDLOCK,1 PAIR 1/2 1
30 220102.1000 WASHER, LOCK, NORDLOCK, 1 PAIR, 5/8 8
3 31 230101.1600 WASHER,LOCK,HI COLLAR 1'' 3
32 H100764 BUSH, HEX, MALE 1 NPT, FEM 1/2 NPT 1
2 33 H100836 ADAPTER, MALE 1/2 ORFS, MALE 1/2 NPT 1
3 34 H100788 STREET ELL 90, 1 NPT 1
PREMIUM
23 24 DIMENSIONS ARE IN INCHES DRAWN JTS 6/23/22 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED JIP 6/23/22 TITLE:
A 12 13
ASSEMBLY, SERVICE A
19 16 ONE PLACE DECIMAL .031
APPR. - -
LOOP MOUNT,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM850, DRILLMEC
3 ADDED ITEMS 34 8/31/2022 JIP THE INFORMATION CONTAINED IN THIS MATERIAL
DRAWING IS THE SOLE PROPERTY OF SIZE PART/DWG NO. REV
B A800381
2 ADDED ITEMS 32 & 33 7/19/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY
1 RELEASE FOR MANUFACTURE 6/23/22 JIP

FINISH
125 Ra UNLESS NOTED OTHERWISE 3
PREMIUM OILFIELD TECHNOLOGY IS
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D 10 D
33
14
32
4
C C
3 34
20 8
9
5
1
B B
5
6
7
15
11
21 PREMIUM
17 DRILLING EQUIPMENT AND SUPPORT
TITLE:
A ASSEMBLY, SERVICE A
25
LOOP MOUNT,
22
GDM850, DRILLMEC
18 B A800381 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 A800045 ROTATE PLATE ASSEMBLY, GDM 850T 1
2 A800367 LINK COLLAR ASSY, GDM850 1
6 3 M500148 SPRING, LOAD COLLAR ASSY 24
D D
4 M500145 SPRING POST, LOAD COLLAR ASSY 24
5 M800354 SPACER, 5/16", SPRING POST, LOAD COLLAR ASSY 48
6 A800271 850T PLATE, GUIDE ANTI ROTATION ASSY 1
7 M800352 STEM, BREAKAWAY MOUNT, CYLINDER, GDM 850T 2
8 M106652 PIN, SPRING, COILED, 1/4" OD X 2" LG 1
9 104112.2200 NUT, HEX, SLOTTED 1 3/8‐6 2
10 M106744 PIN, COTTER, 5/16 X 4 2

C C
11 M100559 WIRE ROPE, 1/16" SS, 7 X 7 SAFETY CABLE 14
12 M100482 1/16" ALIMINIUM OVAL, WIRE ROPE CLIP 26
13 A800383 1
3 4 5
B B

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN JTS 3/28/22 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
2 FRACTIONAL 1/16 CHECKED JIP 3/28/22 TITLE:
A
LINK ASSEMBLY, A
GDM 850
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION -
7 8 9 10 THE INFORMATION CONTAINED IN THIS
MATERIAL
A800368
1 INITIAL RELEASE 3/28/22 JIP

PREMIUM OILFIELD TECHNOLOGY ANY
FINISH
125 Ra UNLESS NOTED OTHERWISE B 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
C C
B
SECTION B-B
1 SCALE 1 : 20
F
2 2
B B
D
2
G UNLESS OTHERWISE SPECIFIED: NAME DATE PREMIUM

TOLERANCES:
A
LINK ASSEMBLY, A
GDM 850
THIRD ANGLE
A800368
9 7 PREMIUM OILFIELD TECHNOLOGY. ANY
PREMIUM OILFIEL TECHNOLOGY IS
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
2
C
4 C
DETAIL C
SCALE 1 : 12
B DETAIL F B
SCALE 1 : 8 2
9 7 10
DETAIL G
SCALE 1 : 16
4 5 3
UNLESS OTHERWISE SPECIFIED: NAME DATE PREMIUM
2 TOLERANCES:
FRACTIONAL 1/16 CHECKED TITLE:
JIP 3/28/22
A
LINK ASSEMBLY, A
GDM 850
THIRD ANGLE
DETAIL D THE INFORMATION CONTAINED IN THIS MATERIAL
SCALE 1 : 12
A800368
PREMIUM OILFIELD TECHNOLOGY. ANY
PREMIUM OILFIEL TECHNOLOGY IS
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ITEM PART NUMBER DESCRIPTION QTY.

NO.
1 M800328 ROTATING PLATE, LOAD COLLAR ASSY, GDM 850T 1
2 M800032 SLEWING GEAR, GDM 850 1
D 3 M800330 BUSHING, ROTATING PLATE PIN BORE, 850T 2 D
4 M100491 EYEBOLT, SHLD TYPE, 3/8-16UNC X 1-1/4in 2
6 008121.1288DH2 CAPSCREW, HEX HEAD, 3/4"-10UNC X 5.50, DH2 48
7 220102.1200 WASHER, LOCK, NORDLOCK, 1 PAIR, 3/4" 48
8 M100559 WIRE ROPE, 1/16" SS, 7 X 7 SAFETY CABLE 22 FT

C 10 H500039 CLAMP, DOUBLE, 3/8 2 C
2 3
1 10 6 7
4 5
56"
1-29/32"
TYP
B B
DETAIL A 7 6
SCALE 1 : 2
34-15/16"
A
3
PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DS 01MAR2022 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED JP 01MAR2022 TITLE:
A
1 ANGULAR: MACH .5 BEND 1
ROTATE PLATE ASSEMBLY A
ONE PLACE DECIMAL .031 APPR.
WITH PIN BORE BUSHING
THIRD ANGLE
NOTE: PROPRIETARY AND CONFIDENTIAL
INTERPRET GEOMETRIC PROJECTION GDM 850T
A. ITEM 8 & 9 ARE SAFETY WIRING COMPONENTS FOR GENERAL REFERENCE THE INFORMATION CONTAINED IN THIS MATERIAL
AND NOT SHOWN IN VIEWS.
B A800045
DRAWING IS THE SOLE PROPERTY OF SEE BOM
1
B. INSTALL ITEM 3 INTO ITEM 1 BY HEATING BORE AND/OR FREEZING ITEM 1 (PRESS FIT.) REPRODUCTION IN PART OR AS A WHOLE
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800021 LINKS LOAD COLLAR, 850 T 1
2 M800063 SLEEVE, LOAD COLLAR 1
3 M800336 LOAD COLLAR REAR BRKT WLDMT 1
4 M800351 MOUNT BRACKET, TILTING PLATE & RLA, GDM 850T 1
D 5 5 M800101 LINK COLLAR TOP PLATE, LOAD COLLAR ASSY, GDM850 1 D
6 M800102 LATCH LOAD COLLAR, LOAD COLLAR ASSY 2

7 M500636 PIN - 1'' X 3'' W/ 1''-8 THREADED END 2
8 M105001 LINCH PIN - WITH LOCKING RING 1/4" 2
9 M100491 EYEBOLT, SHLD TYPE, 3/8-16UNC X 1-1/4in 2
10 M100506 QUICK LINK, 3/8 2
11 M800074 RETAINING RING LOAD COLLAR SLEEVE 1
12 12 M800301 ROTARY UNION MANIFOLD, GDM 850 1
13 M800559 ROTARY MANIFOLD STAND 850T TOP DRIVE 1
13 14 M800175 DOWEL PIN, THREADED, CAPSCREW 3/4-16UNF 4
15 M100917 GREASE FITTING, 1/4 NPT, STRAIGHT 1
C 16 008121.0424DH HEX HEAD CS, GR 8, 1/4- 20UNC x 1 1/2 DRILLED 12 C
17 008121.0816DH2 CAPSCREW,HEX HEAD, 1/2-13UNC X 1.00,DH2 8
18 008121.1636DH2 CAPSCREW,HEX HEAD, 1-8UNC X 2.25,DH2 20
19 026211.1680DH2 CAPSCREW, SOCKET HEAD, 1-8 UNC X 5.00, DH2 10
20 108112.1600 NUT, HEX, PLATED, GR8 1-8 2
24 220102.1600 WASHER, NORD-LOCK, 1 IN, PAIR 20
B 25 230101.1600 WASHER,LOCK,HI COLLAR 1'' 10
B 27 M100482 1/16" ALIMINIUM OVAL, WIRE ROPE CLIP 15 B
28 M100847 SAFETY WIRE-3/16" SS WIRE ROPE 4
4 29 M100485 WIRE CRIMPS-3/16" ALUMINUM 4
2 30 M100089 BEARING BUSHING, ID1.50 X OD1.656 X LG1.50 2
2 30

PREMIUM
TOLERANCES:
A
LINK COLLAR A
ASSEMBLY,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM850
B A800367
2 ADDED BUSHING, ITEM 30 4/18/2022 PREMIUM OILFIELD TECHNOLOGY ANY
1 RELEASE FOR PRODUCTION 11/12/2018

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
13
12
D D
19 25
9 10
13
12
7 8 20
14 23 6
16 22
DETAIL B DETAIL D
SCALE 1 : 6 SCALE 1 : 4
C C
5
13 5
21 17
12 11
5
14
D
B B
5 2
13
C 1
7 8 20
DETAIL C
15 SCALE 1 : 4
6
4
3
24 18
PREMIUM
TITLE:
A 18 24 LINK COLLAR A
1
ASSEMBLY,
2 30
GDM850
SECTION A-A SIZE PART/DWG NO. REV
A SCALE 1 : 12
B A800367 2
WEIGHT: 4316.07 LBS SHEET 2 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800148 PLATE, GUIDE ANTI-ROTATION GDM 850T 1
3 008121.0616DH2 HEX HEAD, 3/8-16 UNC x 1 IN, GR 8 WIRED 3
4 M100559 WIRE ROPE, 1/16 SS, 7X7 SAFETY CABLE 5 FT
D 5 M100482 1/16" ALUMINUM OVAL, WIRE ROPE CLIP 6 D
TIRE WIRE
BOLTS TOGETHER
8.25
3 2
C C
DETAIL A A
SCALE 1 : 3
9.00
B B
.25
3.75
2.50
DIMENSIONS ARE IN INCHES DRAWN HD 05/30/2014

GDS International
TOLERANCES:
7.50 ANGULAR: MACH .5 BEND 1
A ONE PLACE DECIMAL .031
ENG APPR. JP 05/30/2014 850T PLATE, GUIDE A

INTERPRET GEOMETRIC
MFG APPR.
Q.A.
ANTI ROTATION ASSY
MATERIAL
SEE BOM SIZE DWG. NO. REV
01 RELEASE FOR MANUFACTURING JP 07/21/2014

GDS PART No.-Revision
A800271- 01
FINISH
N/A B A800271 01
PROHIBITED.
REV. DESCRIPTION INITIAL DATE DO NOT SCALE DRAWING SCALE: 1:4 WT: 10.61 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

3 4 1 7 1 M800548 BRACKET, WEIGHT SENSOR, GDM 1
850
2 E106019 LIMIT SWITCH, TOP PUSH BEVEL, DC 1
LED
D 3 220102.0600 WASHER,LOCK,NORDLOCK,1 PAIR 2 D
3/8
4 008121.0616DH2 CAPSCREW, HEXHEAD, 3/8-16 X 1" 2
GR. 8
5 230101.01000 WASHER,LOCK, #10 2
6 026211.01016DH CAPSCREW, SOCKET HEAD, #10- 2

24UNC X 1.00, WIRED
7 M800549 TAB, WEIGHT SENSOR, 10-24UNC 1
C C
2 7 1 3 4
2 5 6
A A
5 6 6 5
3 4
B 1 B
SECTION A-A
7 SCALE 1 : 1.5

PREMIUM
TOLERANCES:
A

THREE PLACE DECIMAL .005 WEIGHT SENSOR
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION GDM 850
B A800383
1 RELEASE FOR ASSEMBLY 7/20/2022 JP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 A100246 ASSEMBLY, CYLINDER, 3.25" BORE X 1.75" ROD X 13.5" 2

STROKE, GDM 850T
2 A800353 BAIL CLAMP ASSY, 750T, GDM 2

D D
3 M800341 MACHINING, CRANK, LINK TILT, GDM 850T 1
4 M108635 LINK PLATE ELEVATOR TILT 2
5 M108631 PIN, TILT PLATE CYLINDER, GDM850 2
6 M108632 PIN, TILT PLATE, GDM850 2
7 M108634 PIN, BAIL CLAMP, GDM850 2
8 M800349 BEARING BUSHING, ID1.50000 X OD1.6563 X LG1.0000 4

C C
9 M102283 PIN, COTTER, 5/32 x 2.5 2
10 M106744 PIN, COTTER, 5/16 X 4 4
11 M105812 PIN, ROLL, .25 x .75 LG, ZINC PLT 4
12 104112.1400 NUT, HEX, SLOTTED 7/8-9 UNC 2
13 104112.2000 NUT, HEX, SLOTTED, 1 1/4-7 4
14 H500021 ELL90º, MALE 3/8" ORFS, MALE 1/2" ORB 4

B ROD STOP ASSEMBLY, CYLINDER, ELEVATOR TILTING, GDM B
15 A800056 2
750T

PREMIUM
TOLERANCES:
A
ELEVATOR TILT A
PLATE ASSEMBLY,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION W/ LINK, GDM850
A800372
1 RELEASE FOR PRODUCTION 04/13/22 JIP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
10
13
1
D B D
6 10 13 8 15 1
5 10 13 11
C 5 A C
SECTION A-A
SCALE 1 : 3 A 14
SLOTTED END
OF ITEM 4
TO THIS SIDE
13
4
B B
7 9 12 10 6 2
11
SECTION B-B PREMIUM

SCALE 1 : 3 DRILLING EQUIPMENT AND SUPPORT
TITLE:
A ELEVATOR TILT A
PLATE ASSEMBLY,
W/ LINK, GDM850
B A800372 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 M800374 ROD STOP, CYLINDER, ELEVATOR TILTING, GDM 750T 1

1.756 2 230101.0500 WASHER, LOCK, HI COLLAR 5/16 4
D 3" D
3 026211.0521DH CAPSCREW, SOCKET HEAD, 5/16-18UNC X 1-5/16, DH 4
1 2 3
1
C C
SECTION A-A
SCALE 1 : 1.5
3
1 2 3
B B
A
3"

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DS 13MAY2022 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED JP 13MAY2022 TITLE:
A A
ONE PLACE DECIMAL .031 APPR. ROD STOP ASSEMBLY A
CYLINDER
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION ELEVATOR TILTING, GDM 750T
B A800056
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NOTES: 1 M800581 BAIL CLAMP BASE PLATE, 750T, GDM. WELDMENT 1
1. ITEMS #8, 9 & 10 NOT SHOWN 2 M800582 U-BOLT 1-8 UNC, 750T, BAIL CLAMP 2
D 3 101112.1600 HEX NUT, STOVER, 1-8UNC 4 D
2 4 M108633 PIN, BAIL CLAMP, GDM850 1

2 5 104112.1400 NUT, HEX, SLOTTED 7/8-9 UNC 1
SAFETY WIRE 1 2 6 M102283 PIN, COTTER, 5/32 x 2.5 1

PIN HERE
7 M100847 SAFETY WIRE-3/16" SS WIRE ROPE 1.5
8 M103175 3/16 STOP SLEEVE ALUM COMP 1
9 M103173 HOURGLASS SLEEVE ALUM, 3/16 IN (OVAL SLEEVE ALUM) 1
C C
6.060
1
B B
6
4
5
GDS International
DIMENSIONS ARE IN INCHES DRAWN MH 11/06/2014

TOLERANCES:
FRACTIONAL 1/16 CHECKED JP 11/11/14 TITLE:
A
ONE PLACE DECIMAL .031 APPR. JP 11/11/14
BAIL CLAMP ASSY, A
750T/850T, GDM
THIRD ANGLE
B A800353
2 CHANGED PIN, ADDED CASTLE NUT AND COTTER PIN 4/13/2022 JIP GLOBAL DRILLING SUPPORT INTL. ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
CUSTOMER SUPPLIED
TRAVELING BLOCK 1 M800356 BEAM, BLOCK INTERFACE ASSY, GEARBOX 1
& BLOCK, GDM 850T
D 2 M800357 SIDE LOAD PLATE, BLOCK INTERFACE ASSY, 2 D

GEARBOX & BLOCK, GDM 850T
3 M800358 SIDE PLATE RETAINER PLATE, BLOCK 2

INTERACE ASSY, GDM850
15
4 H800000 CYLINDER, HYDRAULIC 5IN BORE X 10IN 2
STROKE W/ OUT CLEVIS
5 M102871 PIN/CLEVIS, CYLINDER COUNTERBALANCE 2
6 M800355 PIN, 1-3/8", COUNTER-BALANCE CYLINDER, 4

1 GDM 850T
7 008121.0628DH CAPSCREW, HEXHEAD, 3/8-16 X 1.5" GR. 8 4
C 8 101112.0600 NUT,HEX,STOVER C 3/8-16 4 C

9 H101030 ELL 90°, MALE 1/2 ORFS, MALE 3/4 ORB 4
10 11 10 008121.1640DH2 CAPSCREW, HEX HEAD, 1"-8 UNC X 2.50, 8
DH2
11 209202.1600 WASHER, LOCK, 1" 8
239-1/16"
5 3 BEARING BUSHING, ID1.375 X OD1.53125 X

12 M800359 LG1.00, GARLOCK P/N: 22DU16 4
13 M103570 BEARING BUSHING, ID1.375 X OD1.531 X 4

LG0.75, GARLOCK P/N: 22DU12
2
14 - GEARBOX, 850T 1
B 4 15 - TRAVELING BLOCK 1 B
16 M800125 PIN LOAD SIDE PLATES TOP DRIVE 4

137"
6
NOTE: ITEM 14 & 15 ARE FOR ILLUSTRATION ONLY, AND
NOT INCLUDED IN THE FABRICATION BOM.
8 7
9
PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DS 31MAR2022 DRILLING EQUIPMENT AND SUPPORT
16 16
TOLERANCES:
JP 31MAR2022
A
BLOCK INTERFACE ASSY A
14 TWO PLACE DECIMAL .015
GEARBOX & BLOCK
THIRD ANGLE
64-23/32" THE INFORMATION CONTAINED IN THIS MATERIAL
67-1/4" SEE BOM
A800369
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
64-23/32"
C D
D
6 7 8
10 11 3
9
C 5
4
C 2 C
A 3-1/8"
13 12
3"
133-9/16"
6
6 A
7 8
B B
7.69
TYP
SECTION C-C
SCALE 1 : 16
2 2 DETAIL B
SCALE 1 : 2
B
PREMIUM
16
16 TITLE:
A BLOCK INTERFACE ASSY A
GEARBOX & BLOCK
GDM 850T
SECTION A-A SIZE PART/DWG NO. REV
52"
SCALE 1 : 16
B A800369 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
PIN RETAINER HOLES

C
PIN RETAINER SUPPLIED TOWARD BACK OF GEARBOX C
BY CUSTOMER
TRAVELING BLOCK PINS

SUPPLIED BY CUSTOMER
B B
PREMIUM
TITLE:
A BLOCK INTERFACE ASSY A
GEARBOX & BLOCK
GDM 850T
B A800369 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 A801003 GDM HYDRAULIC VALVE BANK ASSY, SHORT GRABBER 1
1 2 A800270 850T PLATE, CAPTURE ANTI‐ROTATION ASSY 1
2 3 A800346 GDM 850, BRAKE ARM ASSEMBLY 1
5 4 A800361 PIPE HANDLER MOTOR ASSY GDM850 1
17 40 34 5 M800076 SERVICE PLATE WELDMENT, GDM 850 1
6 M800081 PIN BASE CYLINDER 1
D 7 m800082 PIN ROD END CYLINDER 1 D
8 M800083 PIN BRAKE LOCK 1
9 M800084 PIN BRAKE BLOCK 2
2 10 M800085 BAR PIN LOCK 2
C B 11 M800086 LEVER BRAKE OUTER 1
33 12 M800087 LEVER BRAKE INNER 1
2 13 M800181 BRAKE BLOCK LOCK PIVOT 1
14 M800091 BRAKE BLOCK LINK PIVOT TOP 1
15 M800093 N5000‐175 TRUARC INTERNAL RETAING RING 1‐3/4 DIA 2
16 M800094 3/4" RETAINING RING TRUARC N5000‐75 2
17 M800160 BRACKET LUBE PUMP GDM 850 1
4 18 M800179 BRAKE BLOCK LINK PIVOT, SERVICE PLATE ASSY, GDM750 1
2 19 M800180 BRACKET, SENSOR, HANDLER ROTATE 1
20 M800182 SHOULDER BOLT, 850T BRAKE BLOCK 6
21 M800302 PIN, CYLINDER SLEW LOCK, GDM850 1
C 22 M800565 ADAPTER, LOWER CAGE, GDM 850 2 C
22 A 23 M500075 KNUCKLE CYLINDER ROD, SERVICE PLATE ASSY 1
24 M500096 EXTERNAL RETAINING RING 3/4'' 1
25 H101027 ELL 90, MALE 1/2 ORFS, MALE 1/2 ORB 4
26 H101517 VLV, HYD, CHECK, INLINE, PILOT, 1/4 NPTF 1
9 27 H100662 PLUG, SOCKET HEX, 1/2'' ORB 2
42 36 10 28 H101854 CYLINDER 1
9 10 42 36 29 H500017 ADAPTER, MALE 3/8 ORFS, MALE 1/4 NPT 3
30 H500020 TEE, SWIVEL BRANCH, #6 ORFS 1
20 43 46 31 H500042 MANIFOLD, 6 PORT 1
32 E106016 PROXIMITY SENSOR, M18, HANDLER LOCK 1
2 13 33 M104223 PIN, DOWEL, 5/8'' X 2'' 4
35 41 34 008121.0524DH CAPSCREW, HEX HEAD, 5/16‐18 x 1.50, DH2 4
35 008121.0636DH CAPSCREW,HEX HEAD, 3/8‐16UNC X 2.25,DH 2
20 26 36 008121.0824DH2 CAPSCREW, HEX HEAD, 1/2‐13UNC X 1.50, DH2 8
2
37 026211.01048DH CAPSCREW, HEX SOC HD, # 10‐24UNC x 3.00 DH 4
B B
29 38 026211.1852DH2 CAPSCREW,SOCKET HEAD, 1‐1/8‐7UNC X 3.25, DH2 12
37 45 39 026211.1860DH2 CAPSCREW, HEX HEAD, 1‐1/8‐7UNC x 3.75, DH2 8
46 43 41 220102.0600 WASHER,LOCK,NORDLOCK,1 PAIR 3/8 2
31 42 220102.0800 WASHER,LOCK,NORDLOCK,1 PAIR 1/2 8
DETAIL A 45 230101.01000 WASHER,LOCK, #10 4
SCALE 1 : 6 DETAIL C 46 101112.1400 HEX NUT, STOVER, 7/8‐9UNC 6
SCALE 1 : 6 47 M100482 1/16" ALIMINIUM OVAL, WIRE ROPE CLIP 40
25
27
PREMIUM
DETAIL B TOLERANCES:
A
SCALE 1 : 6 ANGULAR: MACH .5 BEND 1
SERVICE PLATE ASSY, A
850 TON TOP DRIVE
THIRD ANGLE
SEE BOM
A800370
B
2 CORRECTED ITEMS 13, 18, 19, & 20. ADDED FORWARD HOLES FOR ITEM 17 7/27/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
F
D D
14 36 42
16 6 3 12 7 15
28 21 24
D
23
C C
DETAIL F
SCALE 1 : 6
39 44
39 44
11
B B
22
19
32
G
38 44 DETAIL G
SCALE 1 : 6
PREMIUM
TITLE:
A SERVICE PLATE ASSY, A
850 TON TOP DRIVE
-
DETAIL D 8 15 SIZE PART/DWG NO. REV

SCALE 1 : 4 B A800370 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

5 5 4 6 6 4 4 6 7 8 1 1 H500098 MANIFOLD, HIC, VALVE STACK 1
4 H101342 SOLENOID, VALVE, 3-POS 24 VDC 3
D 5 H101341 SOLENOID, VALVE, 2-POS 24 VDC 2 D
6 H500099 SOLENOID, VALVE, 3-POS 24 VDC 3
7 026113.01032 CAPSCREW, HEX SOC HD, # 10-24UNC x 2.00 32
8 230101.01000 WASHER,LOCK, #10 32
9 H500029 ADAPTER, 5/8 ORB MALE - 1/4 ORB FEMALE 2
11 H103553 ELL 90°, MALE 3/8 ORFS, FEM SWV 3/8 ORFS 2
12 H101033 ELL 90°, MALE 3/4 ORFS, MALE 5/8 ORB 2
14 H101420 TEST STATION #4 SAE 14
C 17 H101001 ADAPTER, MALE 1/2 ORFS, MALE 1/2 ORB 1 C
18 H101075 TEE, FEM SWV BRANCH, MALE 1/4 ORFS 2
2 3 20 M102254 BRACKET, HYDRAULIC MANIFOLD,GDM850 1
21 H100668 REDUCER, MALE 5/8 ORB, FEMALE 3/8 ORB 1
22 M102399 PIN, HYDRAULIC MANIFOLD BRACKET 1
20
21 10
B B
20
1
12
10
12 NAME DATE
GDS International
TOLERANCES:
TITLE:
10 FRACTIONAL 1/16 CHECKED DS 8/12/2022
A
ONE PLACE DECIMAL .031 APPR. JP 8/12/2022 GDS HYDRAULIC A
THREE PLACE DECIMAL .005 VALVE BANK
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION ASSY, SHORT GRABBER
A801003
01 RELEASE FOR MANUFACTURE 8/12/2022 JP

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
15 16 14 11 15 16 15 16 13 14 17 15 16 13 14 13 14 13 14 13
13
3
15
C C
14
16
14
16
15
15
14
2
B
16 18 18 B
19 19
9 9
22
15 12 16 14 11 15 16 16 15 13 14 14 16 15 13 14 14 13 13 14 13
GDS International
TITLE:
A GDS HYDRAULIC A
VALVE BANK
ASSY, SHORT GRABBER
B A801003 01
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 M800147 PLATE, CAPTURE ANTI-ROTATION GDM 850T 1
12.00 2 220102.1200 WASHER,LOCK,NORDLOCK,1 PAIR 7/8 3
3 008121.1224DH2 HEX HEAD, 3/4-10 UNC X 1-1/2 IN, GR 8 DRILLED HEAD 3
D 4 M100559 WIRE ROPE 1/16 SS, 7X7 SAFETY CABLE 5 FT D
5 M100482 1/16" ALUMINUM OVAL, WIRE ROPE CLIP 6
TIE WIRE
C
BOLTS TOGETHER C
DETAIL A 1
SCALE 1 : 3
8.53
B B
2
1.00
A
DIMENSIONS ARE IN INCHES DRAWN HD 05/30/2014

GDS International
TOLERANCES:
A ONE PLACE DECIMAL .031
ENG APPR. JP 05/30/2014 850T PLATE, CAPTURE A

INTERPRET GEOMETRIC
MFG APPR.
Q.A.
ANTI-ROTATION ASSY
MATERIAL
SEE BOM SIZE DWG. NO. REV
01 RELEASED FOR MANUFACTURING JP 07/21/2014

GDS PART No.-Revision
A800270-01
FINISH
B A800270 01
PROHIBITED.
REV. DESCRIPTION INITIAL DATE DO NOT SCALE DRAWING SCALE: 1:4 WT: 17.77 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800557 GDM 850, BRAKE ARM TOP PLATE 1
2 M105146 DOWEL PIN, 3/8 X 1 3/4 1
3 M105147 DOWEL PIN, 1/2" X 1 3/4" 1
D D
4 M800080 ARM BRAKE 1
5 044212.0626 FLATHEAD SOCKET SCREW 3/8" X 4
1.625"
1 5
2 5 5
5 5
3
5
C 5 C
3
4
B B
1

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN JAV 4/13/2014 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. - - GDM 850 A

THREE PLACE DECIMAL .005 BRAKE ARM
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION ASSEMBLY
B A800346
FINISH
DO NOT SCALE DRAWING WEIGHT: 78.97 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 H500154 1.00-20 SLOTTED NUT, MOTOR, HANDLER ROTATE 1
2 H500155 KEY KIT, MOTOR, HANDLER ROTATE 1
3 M800311 PINION, SLEW RING 1
D D
5 M800312 RING, ADAPTER, HANDLER ROTATE MOTOR 1
6 230101.0800 WASHER, LOCK, HI COLLAR 1/2" 4
11 9 8 7 026211.0844DH2 CAPSCREW,SOCKET HEAD, 1/2-13UNC X 2.75, DH2 4
9 026211.0620DH2 CAPSCREW,SOCKET HEAD,3/8-16UNC X 1.25, 8
10 H500104 MOTOR, HANDLER ROTATE 1
C C
10 7 6
B B
5
2
3
GDS International
1 DIMENSIONS ARE IN INCHES

TOLERANCES:
DRAWN DGW 4/14/15
ITEM 3 REMOVED FOR CLARITY FRACTIONAL 1/16 CHECKED DF 4/14/15 TITLE:

A
ONE PLACE DECIMAL .031 APPR. DGW 4/14/15
PIPE HANDLER A
MOTOR ASSY
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM 850
B A800361
01
FINISH
01 RELEASE FOR MANUFACTURE 4/14/2015 DGW 125AA UNLESS STATED OTHERWISE
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 E100026 MOTOR, AC, 2 HP, 460V, 1750 RPM 1
2 M100114 CPLG, SPIDER ELEMENT STYLE A NBR MAT 1
3 M100113 CPLG, HALF, 7/8 BORE, 3/16 KEY 2
D D
4 M100845 HOUSING, BELL, SAE A X 145 TC - 4.25 LG 1
5 M800178 KEYSTOCK, MACHINE, STEPPED, 1/4 x 3/16 .0625 FT
1
6 H100625 ADAPTER, MALE 1 1/4 JIC, MALE 1 1/4 ORB 1
7 H101008 ADAPTER, MALE 3/4 ORFS, MALE 1 ORB, S 1
8 008121.0616 CAPSCREW, HEXHEAD, 3/8-16 X 1" GR. 8 4
9 008112.0620 CAPSCREW,HEX HEAD,3/8-16UNC X 1.25, 2
8 10
C
9 10 12 M100559 WIRE ROPE, 1/16" SS, 7 X 7 SAFETY CABLE 4 FT
C
13 H500024 PUMP, GEAR, LUBE SYSTEM, GDM TOP DRIVE 1
15 208202.0500 WASHER,FLAT,Gr8, SAE, YZ, 5/16 4
16 101112.0500 NUT,HEX,STOVER C 5/16‐18 4
17 008121.0528DH CAPSCREW,HEX HEAD, 5/16‐18UNC X 1.25,DH 4
7
B 1 B
17 14 16
3 NOTE:
REMOVE STOCK KEY FROM PUMP AND REPLACE WITH
15 3/4" OF M800178 - STEPPED KEY STOCK.
5 3
2
SEE NOTE
6 UNLESS OTHERWISE SPECIFIED: NAME DATE

PREMIUM
TOLERANCES:
A
ASSEMBLY, A
LUBE PUMP,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION 480V

FINISH
125 Ra UNLESS NOTED OTHERWISE B A500245-480 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M800346 BONNET 850T TOP DRIVE 1
2 2 M800347 ADAPTER, GOOSENECK, 3 INCH 1
1 5 13 3 M800556 850 T MOTOR SUPPORT FRAME WLDMT 1
D D
4 M100967 DOWEL PIN, 1/2'' x 2'' LONG 4
8 10 11 15 5 008121.1244DH2 CAPSCREW, HEX HEAD, 3/4-10UNC x 2.75, DH2 12

6 008121.1660DH2 CAPSCREW HEXHEAD, 1-8UNC x 3.75, DH2 28
18 2 8 008121.20104DH2 CAPSCREW, HEX HEAD, 1 1/4-7UNC X 6.50, DH2 3

9 101112.1600 HEX NUT, STOVER, 1-8UNC 2
19
10 101112.2000 HEX NUT, STOVER 1 1/4-7 UNC 3
11 208202.2000 WASHER,FLAT,Gr8, SAE, YZ, 1 1/4" 3

C C
12 208202.1600 WASHER,FLAT,Gr8, SAE, YZ, 1'' 2
15 220102.2000 WASHER, LOCK, NORDLOCK, 1 PAIR 1 1/4 3

2
21 22 18 H101856 STANDJUMP ACCUMULATOR 2
2
B B
19 H500037 CLAMP, SINGLE, 4 INCH 2

6 14 13 20 21 H101066 TEE, MALE, 1/2 ORB BRANCH, MALE 1/2 ORFS 2
3
2
22 H100671 REDUCER, MALE 1 ORB X FEMALE 1/2 ORB, S 2
14 12 9 6

PREMIUM
TOLERANCES:
A 7 14 ANGULAR: MACH .5 BEND 1
BONNET ASSEMBLY, A
GDM 850
THIRD ANGLE
B A800371
2 ADDED ITEMS 18-22 8/23/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ITEM NO. PART NUMBER DESCRIPTION QTY. ITEM NO. PART NUMBER DESCRIPTION QTY.
1 M800339 GRABBER LEG, PIPE HANDLER, GDM 850T 1 37 M105708 PIN, SAFETY .156 X 3 1
2 M800332 MOUNTING PLATE, SPRNG RETAINER, GDM850 1 38 M800340 CABLE, PIPE HANDLER RETENTION, GDM 850T 1
3 M800539 PIN, RETAINER, SPRING 1 2 39 M108727 BAR, SAFETY, CLAMP CYLINDER, PH-100 1
4 M103089 TRUNION, BUSHING CYL MOUNT TDS-11 PH-75 2 2 40 M800538 LOCKNUT, BEARING, N10 2
D 5 M102213 BEARING, SELF LUB, 1.375 ID X .1.375 LG 2 41 M800331 PIN, TORQUE ARREST, 2.5" OD, GDM 850T 2 D
6 H101325 CYLINDER ASSEMBLY, IBOP, PH75 1 42 008121.0644DH CAPSCREW, HEX HEAD, 3/8‐16UNC X 2.75 2
7 210202.0800 WASHER, LOCK, SPLIT, GR8, 1/2 4 43 101112.0600 NUT,HEX,STOVER C 3/8‐16 2
8 008121.0824DH2 CAPSCREW, HEX HEAD, 1/2-13UNC X 1.50, DH2 4
9 M105817 PIN, SECONDARY RETENTION, DIA 1.0 1
11 M102222 PIN, COTTER, 5/32 X 2.00, SS 5 43
12 A103103 ASSEMBLY, CLAMP CYLINDER 1
13 M800333 BUSHING, WRENCH LEG PIN BORE, 850T 2 41
14 M800329 YOKE, IBOP ACTUATOR, GDM 850T-PH100 1
15 M102402 PIN, PIVOT, YOKE 2
16 M102278 BEARING, SELF LUBE, 1.00 ID X .75 LONG 2 1
C C
17 M105812 PIN, ROLL, .25 x .75 LG, ZINC PLT 2
18 M100613 CAM FOLLOWER, IBOP CRANK ASSY 2 30
19 209202.1400 WASHER, LOCK, 7/8 2 6
20 M102333 NUT, HEX, 7/8" X 14 UNF 2 4 29
14
21 M100635 GREASE FITTING, 1/8-27 NPT, STRAIGHT 2
22 M105810 SHACKLE, CHAIN, BOLT TYPE, 4 3/4 TON, G-2150 1
23 M104144 PIN, SECONDARY RETENTION 2 3
14
24 104112.1000 NUT, HEX, SLOTTED 5/8" X 11 2
25 008121.1240DH2 CAPSCREW, HEX HEAD, 3/4-10UNC x 2.50, GR8, DH2 4 15
26 210202.1200 WASHER,LOCK,SPLIT,GR8, 3/4 5
27 M108540 SPACER, LARGE, SPRING RETAINER 1 12
B 28 M102276 BEARING, SELF LUBE, 1.00 ID X .50 LONG 2 B
29 H102041 90 ELBOW, #6 JIC MALE, #8 ORB MALE 2
30 E103865 CAP, 9/16-18, #6 2
31 M102849 SPRING, COMPRESSION 1
32 M108541 SPACER, LARGE, SPRING RETAINER 4
33 M108081 CAPSCREW,HEX HEAD, 3/4‐10UNC X 4.00, DH2 1
35 M102248 PIN, COTTER 1/8 X 1.5, SS 1
36 104111.1600 NUT, HEX SLOTTED, 1‐14 UNS, CAD PLATED 1

PREMIUM
TOLERANCES:
A
ASSEMBLY, A
TORQUE ARRESTOR,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM 850
3 CHANGED PART NUMBER OF ITEM 23 6/27/2022 JIP THE INFORMATION CONTAINED IN THIS MATERIAL
A103104
B
2 CHANGED PART NUMBER OF ITEM 3, ADDED ITEM 40 5/18/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D
9
13 5
28 1 41
14
2X
D D
10
11 6
SECTION B-B 29 30
SCALE 1 : 3
42 C C
23 3
11 24
41 6 4
41
C B B 7 8 C
13 SECTION C-C
A A SCALE 1 : 3
18 19 20 21 38
11
11 24 23 3 14 10
1 1
2 25 26
B SECTION D-D B
SCALE 1 : 11
14
36 37 39
2X 22
12 E 16
2 40 15 17
SECTION A-A
SCALE 1 : 3
PREMIUM
31 TITLE:
A ASSEMBLY, A
TORQUE ARRESTOR,
3 2 GDM 850
32 27
E SIZE PART/DWG NO. REV
33
SECTION E-E
34 ? 26 D
B A103104 3
SCALE 1 : 11 WEIGHT: LBS SHEET 2 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 A103102 ASSEMBLY, GRABBER BODY, PH-100 1
2 M103075 LINER, STABILIZER 2
M STAMPING/MARKING INFORMATION: 4 M102338 PIN, GRABBER HINGE 2
P/N: A103103 5 M103044 RETAINER, HINGE PIN, PH-75 2
PO: 6 M102170 MODIFIED, SHOULDER BOLT 2
D 7 210202.0800 WASHER, LOCK, SPLIT, GR8, 1/2 12 D
8 008121.0820DH2 CAPSCREW,HEX HEAD,1/2-13UNC X 1.25,DH2, ZINC PLTD. 8
9 M102404 PIN, CLEVIS, 5/16'' STAINLESS STEEL. 2
10 M103543 SPLIT RING S.S. F/PH-75 CLAMP CYL. ASSY 2
11 M103076 STABILIZER, FRONT 1
M 13 008121.1688DH2 CAPSCREW, HEX HEAD, 1"-8 UNC 2
14 H101414 SPRING, DIE 2
15 104111.1600 NUT, HEX SLOTTED, 1‐14 UNS, CAD PLATED 2
16 M102172 3/16" X 1-3/4" LG STAINLESS STEEL, COTTER PIN 2
17 A100209 STABBING GUIDE ASSY. 6.25 - 7.50 TOOL JOINT (NC50 - 5 1/2 FH) 1
19 M104285 SECONDARY RETAINER PLATE, STUD 4
20 M103249 HINGE PIN SECONDARY RETAINER 2
21 104112.0800 NUT, HEX, SLOTTED 1/2" X 13 4
C 22 M100303 COTTER PIN 4 C
24 M103007 DIE BLOCK KEYS 2
25 A100110 JAW ASSY, NC50 - 5 1/2 FH (SET), 6.25" - 7.50" T.J. 2
26 M100765 EYEBOLT, 3/8"-16 UNC, 1-1/4" THREAD LG 2
29 005121.0544DH2 CAPSCREW, HEXHEAD, 5/16‐18UNC x 2.75, DH2 8
31 A103101 MANIFOLD ASSEMBLY, GRABBER BODY, W/O LIFT 1
32 S500001 O-RING, .75 X 1 X .125, N-70 2
33 C100295 LOCTITE, BLUE A/R
34 M103042 CABLE, 3/64", WLL 54 LBS A/R
35 M102990 FERRULE, CABLE, .136 x .219 6
36 M106197 GREASE FITTING CAP, RED PLASTIC 6
37 M103968 GATE, CLAMPING CYLINDER 1
B B
NOTES:
1. APPLY ANTI-SIEZE AND TORQUE ALL BOLTS PER GDS FORM 330.
2. CLEAN AND LIGHTLY LUBRICATEALL SEALS AND SEAL SURFACES PRIOR TO ASSEMBLY.
3. FULLY TORQUE AND LOCKWIRE AT NEXT ASSEMBLY. UNLESS OTHERWISE SPECIFIED: NAME DATE
PREMIUM
4. TORQUE BOLT UNTIL WASHER IS IS FLUSH WITH FRONT STABLIIZER. DIMENSIONS ARE IN INCHES DRAWN JTS 3/15/22 DRILLING EQUIPMENT AND SUPPORT
5. GREASE ALL GREASE FITTINGS AFTER NEXT ASSEMBLY. TOLERANCES:
A
6. SECURE SHOULDER BOLT USING RED LOCTITE. ANGULAR: MACH .5 BEND 1
JIP 3/15/22
ASSEMBLY, A
7. BREAK ALL SHARP EDGES. ONE PLACE DECIMAL .031 APPR. - -
8. STAMP PART NUMBER AS SHOWN.

CLAMP CYLINDER,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION W/O LIFT
A103103
B
2 REMOVED ITEMS 8, 7 & 32 (LIFT HANDLE GUARD AND HARDWARE) 6/27/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
A B
37
B
D D
A 3
17
11
C C
9 10
29 30 32
2X 7 8 6 5
4
1 3
B B
PREMIUM
TITLE:
A ASSEMBLY, A
CLAMP CYLINDER,
W/O LIFT
26 27 28 26 27 28 SIZE PART/DWG NO. REV

28
B A103103 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
8 8 5
2 7 8 6 10 4 1 14 12 15
2
D D
13
16
37
24
24
37
C C
25
25
17
B 23 18 B
20
18 7 21 22 19
17
SECTION B-B
SECTION A-A SCALE 1 : 3 PREMIUM
SCALE 1 : 3 DRILLING EQUIPMENT AND SUPPORT
TITLE:
A ASSEMBLY, A
CLAMP CYLINDER,
W/O LIFT
B A103103 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

4 1 M800334 WELDMENT, GRABBER BODY WITH EARS 1
5
3 2 H102163 PISTON, PH 40 1
D 3 M102249 RING, CYLINDER HEAD 1 D
4 H102575 CYLINDER HEAD, IR-1000 1

2
5 S100364 SEAL, ROD 1
8 7 A 6 M103678 FLANGE PROTECTOR 2
7 S100363 PISTON SEAL 2
8 S100365 WIPER, ROD 1
2
DETAIL B
SCALE 1 : 2
DETAIL C
C SCALE 1 : 2 C
4
1
6
B
B B
NOTES:
1. CLEAN AND LUBRICATE ALL SEALS AND SEAL
SURFACES PRIOR TO ASSEMBLY.
2. ORIENT KEYWAY PARALLEL TO TOP FACE FOR NEXT ASSEMBLY.
3. PRESSURE TEST PER NOV SPEC TS000362. INSTALL ITEMS 6 AFTER TEST.
4 IF NOT BUILDING OUT NEXT LEVEL, MASK/PLUG ALL OPEN PORTS.
A
PREMIUM
SECTION A-A DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN JTS 3/15/22 DRILLING EQUIPMENT AND SUPPORT
SCALE 1 : 6 FRACTIONAL 1/16 CHECKED JIP 3/15/22 TITLE:
A
ASSEMBLY, A
GRABBER BODY,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION PH-100 W/O LIFT

FINISH
125 Ra UNLESS NOTED OTHERWISE B A103102 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

IBOP LWCV, 8.88/8.63 OD, 7 5/8
1 R800007 REG BOX X 7 5/8 REG BOX, 37 INCH 1
LG
2 A800349 ASSEMBLY, 8.88 VALVE CLAMP 1
D D
3 M800323 SHELL, IBOP ACTUATOR, GDM 850 1
4 M102478 ASSEMBLY, EXTERNAL CRANK, IBOP 2
2 5 S100369 WASHER, LOCK TAB, .56 DIA 4
6 008121.0628DH CAPSCREW, HEX HEAD, 1/2-13UNC 4

X 1.75, DH2 GR8
2
7.44
3
8.88 CLOSED
NOTES:
1. IBOP VALVE ASSEMBLY SHOWN IN THE CLOSED POSITION.
C 4 2. ITEM 4 ARM MUST BE INSTALLED AT 90 FROM BASE. C
VALVE POSITION MUST BE AT 50% OPEN. AND INSTALL
CRANKS THRU WINDOW IN SHELL.
3. CHECK UPPER BALL VALVE POSITION AFTER INSTALL.
4. GREASE ALL PORTS AFTER FINAL ASSEMBLY.
A
3
37.0
B B
8.63 5 6
SHOWN IN
CLOSED POSITION
DETAIL A
SCALE 1 : 4

PREMIUM
TOLERANCES:
A

THREE PLACE DECIMAL .005 IBOP ACTUATOR
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION DUAL BALL, GDM 850
-
B A800048

FINISH
DO NOT SCALE DRAWING WEIGHT: 541.366 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

2 3 6 2
1 M800162 CLAMP, IBOP CONNECTION, 8.88 1
REFERENCE 2 R100030 TONG DIE, 1/2 X 1-1/4 X 5 LONG 4

8.88 INCH VALVE USE TONG DIE P/N R100030. 3 M800163 RETAINER, TONG DIE, GDM 4
8.45 INCH VALVE USE TONG DIE P/N R100749.
D D
4 026211.1040DH2 CAPSCREW, SOCKET HEAD, 5/8-11 10
UNC x 2.50
5 230101.1000 WASHER,LOCK, HI COLLAR 5/8" 10
6 026211.0616DH2 CAPSCREW, SOCKET HEAD, 3/8- 4

16 UNC X 1.00, DH2
1 6 SECTION A-A 3 NOTES:
B SEATING DIE BLOCKS INTO VALVE BODY
1. POSITION ASSEMBLY HALF LENGTH OF DIE BLOCK ON MAINSHAFT
.215 AND HALF ON VALVE. TIGHTEN CLAMP ASSEMBLY ONTO IBOP.
1 2. STRIKE OUTSIDE OF CLAMP IN THE DIE BLOCK AREA WITH HAMMER
8.450 TO SEAT THE DIES INTO THE BODY OF THE VALVE.
4 3. TIGHTEN CLAMP ASSEMBLY.
C 4. REPEAT STEPS 2 TO 3 TIMES, THEN TORQUE ITEM 4 TO 225 FT/LBS. C
5. LIGHT OIL OR ANTI-SEIZE MUST BE USED ON BOLTS.
A A
5
5
.438
9.00
1
11.82
B B
B
3 SECTION B-B
8.88
1
GDS International

TOLERANCES:
FRACTIONAL 1/16 CHECKED JV 8/19/14 TITLE:
ASSEMBLY, 8.88
A ONE PLACE DECIMAL .031 ENG APPR. XXX
A
XX/XX/XX

INTERPRET GEOMETRIC
MFG APPR.
Q.A.
XXX XX/XX/XX VALVE CLAMP
TOLERANCING PER: ASME Y14.5M XXX XX/XX/XX
MATERIAL
B A800349
01 RELEASE FOR PRODUCTION JP 8/19/14

01
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 E107925 MOTOR, AS VERTICAL, 1200HP, 600V 1
2 030221.2472DH BOLT, SUPER, SB12-150-6-450 4
3 A500231 ASSY, MOTOR, DISC BRAKE 1
D D
4 A500255 SEAL RING HOUSING ASSEMBLY, GE 1
B20
5 H102495 FITTING, PIPE 3'' HOSE END X 3'' MNPT 1
STL 3/8 TC HOSE
6 M104035 SEAL RING, GE B20 1
7 N100495 1024 PULSE ENCODER WITH DOUBLE 1
RECEPTICLE
8 M500335 SHAFT, MAIN ENCODER, GDM 1
9 A800036 5GE20B HUB & ADAPTER FLANGE 1
10 E107926 ASSY, BLOWER, 15HP, 480V, GDM, 1
GULF
11 M500331 PLENUM, GE B20 GDM500 1
C C
12 M500613 INSERT, AC PLENUM 2
13 M500270-020 SHIM, MOTOR MOUNT BTM, 0.020 1
14 P100057 BREATHER/DRAIN, 3/8 NPT 2
15 220102.0400 WASHER, LOCK, NORDLOCK, 1 PAIR 16

1/4
16 026211.0412DH CAPSCREW,SOCKET HEAD, 1/4- 16
20UNC X 0.75, DH
17 A800384 GDM AC HYDRAULIC AND LUBE 1
MANIFOLD ASSEMBLY
B B

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN JTS - DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
FRACTIONAL 1/16 CHECKED JP - TITLE:
A
ONE PLACE DECIMAL .031 APPR. - - MOTOR ASSY A

THREE PLACE DECIMAL .005 1200HP, 575V
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION 480V BLOWER
B A800373
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 008121.1656 DH2 CAPSCREW,HEX HEAD, 1-8UNC X 3.50,DH2 4
2 016142.1650DH2 CAPSCR, SOCKETHEAD, M16 x 50, GR8.8, DH2 8
3 026211.1048DH2 CAPSCREW,SOCKET HEAD, 5/8-11UNC X 3.00, DH2 8
4 026211.1244DH2 CAPSCREW,SOCKET HEAD, 3/4-10UNC X 2.75, DH2 12 D
D
7 230101.1000 WASHER LOCK HI COLLAR 5/8" 16
8 A500364 ASSY, CALIPER, BRAKE 2
9 M500238 HUB DISC 1
10 M500265 ADAPTER PLATE, DISC BRAKE 2
11 M500267 SHIMS 1
12 M500268 DISC, DISC BRAKE 1
13 M500274 DISC BRAKE HOUSING, DISC BRAKE ASSY 2
9
14 M500275 DISC BRAKE COVER, DISC BRAKE ASSY 1
C 12 5 4 C
15 M500750 BRAKE COVER SHOULDER BOLT 4
SECTION B-B
30.00
6 16 14 3 7 8
15
B B
10
14.13
B B
7 2
13
GDS International

TOLERANCES:
13 1 6 11 9 FRACTIONAL 1/16 CHECKED DGW 10/15/14 TITLE:
A
ASSY, MOTOR, A
2 ONE PLACE DECIMAL .031 APPR. DF 10/15/14
DISC BRAKE
THIRD ANGLE
B A500231
2 ADDED M500750 AND NECESSARY HARDWARE 12/18/2015 DGW N0321
2
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M500325 SEAL HOUSING, GE B20 1
2 S100250 SEAL, DUAL LIP, 8.00 x 9.25 x 0.625 2
3 M500417 SHIELD, OIL, PTFE, GDM 500T 1
4 M100332 RETAINING RING, INT, 9.25 BORE, 0.086 THK 1 D
D
5 M104129 FLAT SOCKET HEAD CAPSCREW, 5/8-11 UNC x 4 INCHES LONG 8
A
5
5
4
1
2
C 3 C
B B
A
SECTION A-A
GDS International
DIMENSIONS ARE IN INCHES DRAWN DGW 5/7/14

TOLERANCES:
FRACTIONAL 1/16 CHECKED DF 10/14/14 TITLE:
A - - - - - ANGULAR: MACH .5 BEND 1
ONE PLACE DECIMAL .031 APPR. DGW 10/14/14
SEAL RING HOUSING A
- - - - - PROPRIETARY AND CONFIDENTIAL TWO PLACE DECIMAL .015
ASSEMBLY
THIRD ANGLE
- - - - -
DRAWING IS THE SOLE PROPERTY OF INTERPRET GEOMETRIC PROJECTION GE B20
GLOBAL DRILLING SUPPORT INTL. ANY TOLERANCING PER: ASME Y14.5M
-
REPRODUCTION IN PART OR AS A WHOLE MATERIAL
- - - - SIZE PART/DWG NO. REV
B A500255
01
01
FINISH
RELEASE FOR MANUFACTURING DGW 10/14/14 N0079 PROHIBITED.
125AA Unless stated otherwise
REV. DESCRIPTION INITIAL DATE ECN # DO NOT SCALE DRAWING SCALE: DNS WEIGHT: 4.85 SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 H500102 VALVE, SOL, HYD, 2 POS, 3 WAY 1
4.27 2 H500016 ELL 90°, MALE 3/8 ORFS, MALE 3/8 NPT 1
4 206101.0500 WASHER,FLAT,HARDENED,F436 Plain, 5/16 2 D
D
5 008121.0544DH CAPSCREW, HEX HEAD, 5/16-18UNC X 2.75,DH 2
6 101112.0500 NUT,HEX,STOVER C 5/16-18 2
7 H102722 PLUG, HOLLOW HEX, 3/8" NPT 1
8 M100559 WIRE ROPE, 1/16" SS, 7 X 7 SAFETY CABLE 1FT
9 M100482 1/16" ALUMINUM OVAL, WIRE ROPE CLIP 2
C C
4 5 6
2
7.39
7
B B
1
2.000
2.95
GDS International

TOLERANCES:
A - - - - - ANGULAR: MACH .5 BEND 1
ONE PLACE DECIMAL .031 APPR. DF 10/20/14
GDM BREAK A
- - - - - PROPRIETARY AND CONFIDENTIAL TWO PLACE DECIMAL .015
VALVE ASSEMBLY
THE INFORMATION CONTAINED IN THIS THIRD ANGLE
- - - - - DRAWING IS THE SOLE PROPERTY OF
INTERPRET GEOMETRIC
PROJECTION
-
REPRODUCTION IN PART OR AS A WHOLE MATERIAL
- - - - SIZE PART/DWG NO. REV
B A500016
01
01
FINISH
RELEASE FOR MANUFACTURE DF 10/20/14 - PROHIBITED.
125AA Unless stated otherwise
REV. DESCRIPTION INITIAL DATE ECN # DO NOT SCALE DRAWING SCALE: DNS WEIGHT: SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M102897 GEB 20 HUB 1
2 M800018 ADAPTER FLANGE, GEB20, GDM850, MOTOR ASSY 1
3 026211.1644 SOCKET HEAD, 1-14 UNS x 2 3/4 IN FINE 12
D D
3 2 1
A
C C
B B
SECTION A-A
SCALE 1 : 3
NAME DATE
GDS International
TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. DF 5/29/15 ASSEMBLY, A
THREE PLACE DECIMAL .005 MOTOR HUB ADAPTER,
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION GDM 850
-
A800036
01 RELEASE FOR MANUFACTURE 5/29/2015 DF

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 M500635 MOUNT, MOTOR MANIFOLD MOUNT, AC 1
4 H101946 MANIFLD , HEADER 1
D 5 H101027 ELL 90, MALE 1/2 ORFS, MALE 1/2 ORB 5 D

7 H500021 ELL90º, MALE 3/8" ORFS, MALE 1/2" ORB 3
9 H100661 PLUG, SOCKET HEX, 3/4" ORB 3
10 H100855 ADAPTER, HEX, FEM 1/2 NPT, MALE 3/4 ORB 1
11 E500186 FLOW METER, TURBINE, 1/2 NPT, 3/4-7-1/2 GPM 1
12 E500187 CONVERTER, 5 PIN, F TO I, CANISTER STYLE, FLOW SENSOR 1
14 H102273 FITTING, 1/2 PIPE COUPLING 1
C C
17 026211.01028DH CAPSCREW, SOCKET HEAD, #10-24UNC X 1.750, WIRED 2
18 230101.01000 WASHER,LOCK,HI COLLAR # 10 2
21 026211.0440DH CAPSCREW, SOCKET HEAD, 1/4-20UNC X 2.50,DH 11
16 15 17 3 20 18 19 5 2 21 22 5 22 230101.0400 WASHER,LOCK,HI COLLAR 1/4 11
23 H500110 ELL 90 DEG, MALE1/4 ORFS, MALE 1/2 ORB 1
6
8
B B
13 1
GDS International

14 12 11 10 5 7 7 7 23 4 9 5 TOLERANCES:
DGW 10/20/14
A
ONE PLACE DECIMAL .031 APPR. DF 10/17/14
GDM AC HYDRAULIC A
AND LUBE MANIFOLD
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION ASSEMBLY
B A500163
01
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 A800348 AUXILIARY J-BOX ASSY, GDM, 850 TON 1
2 A800379 LUBE COOLER ASSY, GDM750 1
3 A500627-1 PLC J-BOX, GDM 1
4 A800375 INSTALLATION KIT, MANIFOLD, HYD ELEVATOR, OPEN/CLOSE 1
5 A800377 INSTALLATION KIT, MANIFOLD, HYDRAULIC ELEVATOR, FLOAT 1
D 6 M100244 ANTI-VIBRATION, RUBBER MOUNT, 3/8 BOLT 8 D
7 M103115 RUBBER, S-PIPE 1
8 M106971-1 S-PIPE, CLAMP BASE, INSIDE, W/LUG 1
9 M800542 WELDMENT, GDM850, GUARD 1
10 M800541 PLATE, MOUNT, J-BOX, GUARD 1
11 M800567 GDM 800, UPPER CAGE MOUNT ADAPTER 2
12 N500004 GAUGE, PRESSURE, 0 - 300 PSI, SS, WIKA,W/FLANGE 1
13 N500005 GAUGE, PRESSURE, 0 - 1000 PSI, SS, WIKA, W/FLANGE 1
14 N500006 GAUGE, PRESSURE, 0 - 3000 PSI, SS, WIKA, W/FLANGE 1
15 R100349-1 TOP, S-PIPE MOUNT, W/LUG 1
16 E102971 NUT,HEX,SS,6-32,NYLOC 9
17 E103858 SCREW, 6-32 X 1.00, SS 9
18 008121.0528DH CAPSCREW,HEX HEAD, 5/16-18UNC X 2.00,DH 4
19 008121.0620DH2 CAPSCREW,HEX HEAD,3/8-16UNC X 1.25,DH2 2
C 20 008121.0624DH CAPSCREW, HEX HEAD, 3/8-16UNC X 1.50 5 C
21 008121.0644DH CAPSCREW, HEX HEAD, 3/8-16UNC X 2.75 4
24 008121.1648DH2 CAPSCREW, HEXHEAD, 1-8UNC x 3.00,DH2 14
25 008121.1664DH2 CAPSCREW,SOCKET HEAD, 1-8UNC X 4.25,DH2 8
26 101112.0600 NUT,HEX,STOVER C 3/8-16 9
27 101112.0500 NUT,HEX,STOVER C 5/16-18 4
28 101112.1000 NUT,HEX,STOVER C 5/8-11 4
29 101112.1600 HEX NUT, STOVER, 1-8UNC 10
B 34 220102.0600 WASHER,LOCK,NORDLOCK,1 PAIR 3/8 7 B
38 230101.1600 WASHER,LOCK,HI COLLAR 1'' 10
40 M800535 PLATFORM, LOWER CAGE, GDM 850 1 2
41 M800536 HINGE PIN, WORK PLATFORM, GUARD, GDM850 2
42 M800532 HINGE PIN, DOOR, GUARD, GDM850 4
43 M800157 PIN, DOOR LATCHING, GDM 850 4
44 M100294 COTTER PIN, 3/32" X 1-1/2" 4
45 M800533 DOOR, ODS, CAGE ACCESS, GDM 850 1
46 M800534 DOOR, DS, CAGE ACCESS, GDM 850 1 UNLESS OTHERWISE SPECIFIED: NAME DATE
PREMIUM
47 104112.0800 NUT, HEX, SLOTTED 1/2" X 13 4 DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN JTS 5/4/22 DRILLING EQUIPMENT AND SUPPORT
48 230101.1200 WASHER, LOCK, HI COLLAR 3/4" 4 FRACTIONAL 1/16 CHECKED JIP 5/4/22 TITLE:
A
GUARD ASSEMBLY, A
GDM850
THIRD ANGLE
B A800374
2 ADDED WORK PLATFORM AND ACCESS DOORS 6/13/2022 JIP PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
39
23 28 32 36
D 6 21 31 26 D
34 26 31 20
35 22 15 7 8 24 29 33 37 11
24 37
19 34
3
2
10
C C
27 30 30 18 6 4
5
25 38
1
29 37
B B
13 17 16
12 17 16
14 17 16
33 24 PREMIUM
TITLE:
A GUARD ASSEMBLY, A
GDM850
-
B A800374 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
43
44 47
43
45
D D
APPLY
9 ANTI-SEIZE
47 44
DETAIL C
SCALE 1 : 6 48
DETAIL D
SCALE 1 : 6
42
SECTION A-A
C SCALE 1 : 4 C
APPLY
ANTI-SEIZE 9
41
40
B A B
38
A
SECTION B-B
SCALE 1 : 4
C
B PREMIUM
TITLE:
A GUARD ASSEMBLY, A
B GDM850
-
B A800374 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
ITEM NO. PART NUMBER DESCRIPTION Default/

QTY.
1 M800570 J-BOX, AUXILLARY, GDM 850T 1
2 E500128 1NPT NYLON WASHER 1
3 E500290 WASHER, NYLON, 1/2 NPT 2 D
D
4 E500176 GLAND, CABLE, EX, 1'' NPT 1
5 E500132 A2EX/20 1/2 NPT 2
6 E100152 CONDUIT FTG, FLEX METAL, STR, 1/2 1

NPT
7 E100236 LOCKNUT, CONDUIT FTG, 1/2 NPT 2
8 E100238 GLAND, CABLE, 1 1/2 NPT, 33.0 - 1

16 42.9mm
15
2X
C C
B B
3 2
4 5 5 6
2X
GDS International
DIMENSIONS ARE IN INCHES DRAWN KHW 8/18/2014

4 2 5 5 TOLERANCES:
FRACTIONAL 1/16 CHECKED XXX XX/XX/XX TITLE:
A A
ONE PLACE DECIMAL .031
ENG APPR. XXX XX/XX/XX
AUXILLARY J-BOX ASSY,
GDM, 850 TON
THREE PLACE DECIMAL .005 MFG APPR. XXX XX/XX/XX
PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC Q.A.
TOLERANCING PER: ASME Y14.5M XXX XX/XX/XX
MATERIAL
B A800348
01 RELEASE FOR MANUFACTURE KHW 8/18/14

01
PROHIBITED. A800348-01 DO NOT SCALE DRAWING SCALE: 1:5 WEIGHT: SHEET 1 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 M800571 BACK PAN, J-BOX, AUXILLIARY, 1

GDM 850T
2 E500272 DIN RAIL, TS35 1
3 E103730 TERM. BLK, FEED THRU, SCR 2 LVL 19 D
D
4 E101072 TERM. BLK, GND, 2 LVL 1
C C
3
19X
B B
1 2
GDS International
TITLE:
A AUXILLARY J-BOX A
ASSY, GDM, 850 TON

SIZE DWG. NO. REV
B A800348 01
SCALE: 1:5 WEIGHT: SHEET 2 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 H500123 COOLER, OIL MOTORLESS, 011 1
2 2 2 2 M800184 PLENUM, LUBE COOLER, GDM850, B20 1
D 3 M800140 LUBE COOLER GUARD, GDM850 1 D
4 M800158 MOUNT, LUBE COOLER, GDM 850 1

5 5 M800545 MOUNT, RH, LUBE COOLER, GDM 850 1
4
6 H500049 ELL 90, MALE#8 ORFS, MALE#16 ORB 1
7 H101035 ELL 90, MALE 3/4 ORFS, MALE 1 ORB 1
8 206101.0600 WASHER,FLAT,HARDENED,F436 PLAIN, 3/8 8

11 5
6 1 16 " 9 008121.0664DH CAPSCREW, HEX HEAD, 3/8-16 x 4.00, DH 4
5
C 1 16 " C
10 101112.0600 NUT,HEX,STOVER C 3/8-16 4
11 H102495 FITTING, PIPE 3'' HOSE END X 3'' MNPT STL 3/8 TC HOSE 1
3
B B
9 8 10

PREMIUM
DIMENSIONS ARE IN INCHES DRILLING EQUIPMENT AND SUPPORT
7 TOLERANCES:
DRAWN JTS 5/4/22

A
LUBE COOLER A
ASSEMBLY,
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM850
B A800379
2 CHANGED PLENUM (ITEM 2) PART NUMBER 8/31/2022 PREMIUM OILFIELD TECHNOLOGY ANY

FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

12 11 1 E500290 WASHER, NYLON, 1/2 NPT 25
17 10
5 15 2 E500288 A2EX/16SS 1/2" NPT NICKEL 4
7 3 E500133 A2EX/20SS 1/2" NPT NICKEL 20
D D
4 E101213 HOLE FOLL, 0.50 IN, STAINLESS STEEL 2
5 E100994 M TO F 90 ELBOW 4
6 E500132 A2EX/20 1/2 NPT 1
15 7 E103806 RTD, 100 OHM, PLAT., 3 WIRE 1
AMBIENT TEMP.
8 E104925 Z BRACKET - 20 IN 1
17 9 9 9 A500403 ASSY., BACKPAN, WAGO, JBOX, 1
15 7 11 12 PLC, GDM
10 P100057 BREATHER/DRAIN, 3/8 NPT 1
15 TRANSDUCER, PRESSURE, 0 TO 300
11 N100476 PSI 2
C C
12 N100477 TRANSDUCER, PRESSURE, 0 TO 3000 2
PSI
6 13 E100236 LOCKNUT, CONDUIT FTG, 1/2 NPT 25
14 E105637 WASHER, NYLON, 3/4 NPT 2
15 E500126 A2EX/25 3/4''NPT NICKEL 2
10 17 M104135-1 PLC J-BOX, GDM 500T 1
6 15 10 12 11
3 2 3 3 2
B 3 3 B
3 3 3 4
15
15
GDS International
DIMENSIONS ARE IN INCHES DRAWN KHW 5/15/2014

4 2 3 2 2 10
TOLERANCES:
TITLE:
PLC J-BOX,
FRACTIONAL 1/16 CHECKED
A
2 3 3 11 ANGULAR: MACH .5 BEND 1
XXX XX/XX/XX
A
5 ONE PLACE DECIMAL .031 ENG APPR. XXX XX/XX/XX
THREE PLACE DECIMAL .005 MFG APPR. XXX XX/XX/XX
GDM 500T,
INTERPRET GEOMETRIC
Q.A. XXX XX/XX/XX WAGO
-
MATERIAL
- - - DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV
B A500627-1
01 RELEASE FOR MANUFACTURE KHW 5/19/14

1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 E500272 DIN RAIL, TS35 1
8 1
13 2 E105658 PLC, PROFINET IO, 2-PORT, WAGO 1
PLC, DIGITAL OUTPUT, 24VDC, 2 CH,
2X 3 E105659 WAGO 12
D D
4 E105642 PLC, DIGITAL INPUT, 16 CH, 24 VDC, 1
14 WAGO
2X 5 E105660 PLC, ANALOG INPUT, 4-20, 4 CH, 3
REMOVABLE TERMINALS, WAGO
15 6 E105647 PLC, RTD MODULE, 2/4 CH, WAGO 1
8X 7 E105646 PLC, BUS END MODULE, WAGO 1

8 M104136 PLC J-BOX, BACKPAN, GDM 500T 1
9 E103907 WIRE DUCT 2X4 DEEP PLASTIC GREY 1
10 E103908 WIRE DUCT COVER, 2" 1
2
11 E105649 GROUND BAR 1
C 10 PLC, COUNTER, DIFFERENTIAL, C
12 E105740 WAGO 1
13 E103733 END STOP, GREY 2
3 WIELAND TERMINAL BLOCK,
14 E103992 W/DIODE, BLUE 2
12X TERMINAL BLOCK, 4 CONDUCTOR
15 E105718 12AWG 8
4 TERMINAL BLOCK, 4 CONDUCTOR
16 E105902 12AWG, GND 1
5
9 3X
B B
6
12
11 GDS International
TITLE:
A PLC J-BOX, A
GDM 500T,
WAGO
SIZE DWG. NO. REV
B A500627-1 01
SCALE: 1:5 WEIGHT: SHEET 2 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 A800376 MANIFOLD, HYDRUAULC ELEVATOR, 1

B+V, OPEN/CLOSE
3/8
D 3 101112.0600 NUT,HEX,STOVER C 3/8-16 2 D
4 026211.0688DH2 Black-Oxide Alloy Steel Socket 2

Head Screw
3 2 NOTES:
C ITEM 1 SUPPLIED BY CUSTOMER. C
B B
4
4

PREMIUM
TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. - - INSTALLATION KIT A

THREE PLACE DECIMAL .005 MANIFOLD, HYD ELEVATOR
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION OPEN/CLOSE
B A800375
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 A800378 MANIFOLD, FLOAT, HYDRAULIC 1
ELEVATORS, B + V
1/2
D 3 101112.0800 NUT,HEX,STOVER C 1/2-13 2 D
4 008121.0868DH2 CAPSCREW, HEXHEAD 1/2-13 UNC x 2

4.25, DH2
C C
NOTES:
ITEM 1 SUPPLIED BY CUSTOMER
B B
2 3

PREMIUM
TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. - - INSTALLATION KIT A

THREE PLACE DECIMAL .005 MANIFOLD
THIRD ANGLE
INTERPRET GEOMETRIC
PROJECTION ELEVATOR FLOAT
B A800377
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

1 2 9 7 10 NO.
1 A800051 SUB-ASSEMBLY, BASE FRAME & 1
RUNNER, ETC., GDM 750T, 66"
2 M800365 ARM, EXTEND FRAME, UPPER 1
3 M800366 ARM, MINOR, EXTEND FRAME, GDM 1
D 19 750T D
19
4 A800052 ASSEMBLY, MOUNT FRAME, TORQUE 1
ATTREST SYSTEM, GDM 750T, 66"
5 H800030 5" BORE, 21-7/16" NET STROKE, 15- 2
20 13/16" STOP TUBE, 2" DIA. ROD
6 M800588 PIN - 2.75 DIA X 7.00 8
5 2
7 M800589 RETENTION PLATE 16
8 M800592 PIN, 2.00" X 4.00" CYLINDER PIN 4
5 9 M800593 RETENTION PLATE, CYLINDER PIN 8
CAPTURE PLATE
10 M100635 GREASE FITTING, 1/8-27 NPT, 12
STRAIGHT
178-5/32"
21 11 M800368 LOCKING LUG, SHIPPING, EXTEND 2

C FRAME, GDM 750T C
2
12 M800369 PIN, 2.00 OD X 7 LG 2
13 M800370 WIRE SNAP COTTER PIN, 0.243" DIA. 2
3 14 209202.0800 WASHER, LOCK, SLPIT, GR5, 1/2 64
15 008121.0826DH2 CAPSCREW,X HEX HEAD, 1/2-13UNC
1.625, DH2 48
16 008121.0822DH2 SCREW, HEX HEAD, GR8

1/2-13 X 1-3/8, 16
4
13
18 008121.0620DH2 CAPSCREW,HEX HEAD,3/8-16UNC X
1.25,DH2 24
12 19 A800055 ROD STOP ASSEMBLY, CYLINDER, 2
B EXTEND FRAME, GDM 750T B
2 20 A100248 1/8" ORIFICE INSERT, EXTEND FRAME 2
11 FITTING, GDM 750T
21 H101027 ELBOW 90 , MALE 1/2 ORFS X MALE 2
2 1/2 ORB
A 3/4" TYP
NOTE: ITEM 11 TO BE WELDED ONTO ITEM 4 ON SITE
27-7/32" TYP
1 4 1 4 1/2" DURING FINAL TOP LEVEL ASSEMBLYING FOR

4 ITEM 11, 12 & 1 TOGETHER.
12 13
11 PREMIUM
20-7/8"

TOLERANCES:
11 FRACTIONAL 1/16 CHECKED JP 06MAY2022 TITLE:
A 13
ASSEMBLY A
12 ONE PLACE DECIMAL .031 APPR.
B B TWO PLACE DECIMAL .015
EXTEND FRAME
SECTION B-B THREE PLACE DECIMAL .005
THIRD ANGLE
GDM 750T, 66"
SCALE 1 : 10 63-3/8" PROPRIETARY AND CONFIDENTIAL
DETAIL A
SCALE 1 : 10 SIZE PART/DWG NO. REV
B
REVISIONS
A800046
2
REV. DESCRIPTION DATE APPROVED REPRODUCTION IN PART OR AS A WHOLE
FINISH
1 INITIAL RELEASE 06MAY2022 JP GLOBAL DRILLING SUPPORT INTL. IS
2 ADDING ITEM 20 & 21 29AUG2022 JP PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 0.00 LBS SHEET 1 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
U N TED
.5 0 O P
L L BE M NG TO
A D I E)
1 9 SH EXTEN E HOL
M S
(ITE SITE BY MOU
D 14 15 15 16 ON IVE T O D
DR
7 10 15 16 18 21 18 18 5 20 19 2
2 2
9
F
F
15
C
15
C C C
168-5/16"
B B
4 3 1
PREMIUM
TITLE:
A ASSEMBLY A
EXTEND FRAME
GDM 750T, 66"
87-5/8" (CUSTOMER REQUIRED) SIZE PART/DWG NO. REV
63-3/8" 94-17/32" B A800046 2

8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D D
G
D
SECTION F-F
C SECTION C-C SCALE 1 : 8 C
SCALE 1 : 8
6 4-2 4 2 10 8 2
B 10 B
14 15
17 18
5 PREMIUM
7 7 DRILLING EQUIPMENT AND SUPPORT
TITLE:
A ASSEMBLY A
EXTEND FRAME
DETAIL D DETAIL G GDM 750T, 66"
B A800046 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
B ITEM
NO. PART NUMBER DESCRIPTION QTY.
A 9 9 A 10 11 6 M M
2 2 1 M800337 BASE, EXTEND FRAME GDM 1
2 M800307 RAIL SLIDER, COATED, GDM 144 IN 4
D D
3 M800363 SPACER, EXTEND FRAME SLIDER, 750T 4
N 4 M105713 BEARING, PLAIN RADIAL, 70 X 105 X 40 4

5 M500398 ROD, GUIDE RUNNER ADJUSTER 8
6 M500399 CLAMP, ADJUSTER ROD, GUIDE RUNNER 8
7 M500729 WASHER PLATE 1/4", RAIL SLIDER TRACK, GDM 8
8 M500400 BRACKET, GUIDE RUNNER ADJUSTER CLAMP 8
9 M100501 EYEBOLT, 1/2 UNC, 1 1/2" LG 6 2
10 026211.0616DH2 CAPSCREW, SOCKET HEAD, 3/8-16 UNC X 1.00, DH2 32
C C
SECTION M-M 11 230101.0600 WASHER,LOCK,HI COLLAR 3/8'' 32
168-5/16"
SCALE 1 : 24
12 230101.1600 WASHER,LOCK,HI COLLAR 1'' 32
13 026211.16102DH2 UNC 1-8 LG 6.375", SOCKET HEAD SCREW, DH2 16
3 13 12
14 026211.1692DH2 UNC 1-8 LG 5.75", SOCKET HEAD SCREW, DH2 16
2
2
2 16 225102.0800 WASHER, LOCK, NORDLOCK, 1 PAIR, 1/2, LARGE 2
5 2 17 101112.0800 NUT,HEX, SS 1/2-13UNC 2
B B
1 2 1 5 15 6
14 6 10 11 5
B SECTION A-A
3 SCALE 1 : 12
15
PREMIUM
15"

TOLERANCES:
A DETAIL N ANGULAR: MACH .5 BEND 1
SUB-ASSEMBLY A
63-3/8"
BASE FRAME & RUNNER
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM 750T, 66"
REVISIONS SIZE PART/DWG NO. REV
B A800051
2
FINISH
2 ADDING TWO EYEBOLTS, ETC. 05AUG2022 JP PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 2440.37 LBS SHEET 1 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
D C
6-3/8"
F 2 9 3 13 12
E
D D
8
P
G .035 15
TYP
4 4 1
1
DETAIL E
SCALE 1 : 6
C C
DETAIL G
SCALE 1 : 4
5-3/4"
2 9 3 14 12
4 4 7
2
B 9 B
1
2
16
DETAIL F
SCALE 1 : 6
2
17
PREMIUM
TITLE:
A SUB-ASSEMBLY A
DETAIL P BASE FRAME & RUNNER

SCALE 1 : 8 GDM 750T, 66"
D C SECTION D-D SECTION C-C SIZE PART/DWG NO. REV
SECTION B-B
SCALE 1 : 20 B A800051 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
2 2 1 M800367 ANCHOR FRAME, EXTEND, GDM 1
1 1 1
T T 2 M105713 BEARING, PLAIN RADIAL, 70 X 105 X 40 4
4 M800364 PAD-BELTED RUBBER - 3.5" X 9" PATTERN 6 D
D
5 008121.0848DH2 CAPSCREW,HEX HEAD, 1/2-13UNC X 8
3.00,DH2
SECTION J-J 6 206101.0800 WASHER,FLAT,HARDENED,F436 Plain, 1/2 8
2 V SCALE 1 : 16 7 101112.0800 NUT,HEX,STOVER C 1/2-13 8
14 8 210101.0800 WASHER,LOCK,SPLIT, SS 1/2 8
2 3 9 9 A500684 KIT, ELECTRICAL, EXTEND FRAME 1
1
14 N 10 A800141 ASSEMBLY, EXTEND FRAME VALVE 1
2 11 A800054 ASSEMBLY, COUNTER BALANCE VALVE & 1
FITTINGS, EXTEND FRAME, 750T
H J J 0.50" BY 0.035" TUBE ASSEMBLY,
2 12 A800057 DIRECTIONAL TO/FROM COUNTER-BALANCE 1
K N F VALVES, EXTEND FRAME, GDM750T
0.50" BY 0.035" TUBE ASSEMBLY-LONG,
C
K 13 A800058 DIRECTIONAL & COUNTER-BALANCE 1 C
11 VALVES, EXTEND FRAME, GDM750T
F
H 14 A101899 LIMIT SWITCH ASSY, EXTEND FRAME 1
12 13
14 12 13
72-7/8"
4
12
B
13 B
14
A A
5 6 7 8 4
14-3/8"

PREMIUM
TOLERANCES:
A
52-1/8"
ASSEMBLY, MOUNT FRAME A
TORQUE ATTREST SYSTEM
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION GDM 750T, 66"
REVISIONS
B A800052
REV. DESCRIPTION DATE APPROVED DRAWING IS THE SOLE PROPERTY OF SEE BOM
2
FINISH
1 INITIAL RELEASE 04MAY2022 JP WITHOUT THE WRITTEN PERMISSION OF
2 MOVE HYDRAULIC PADS TO M800367 WELDMENT, ETC. 04AUG2022 JP PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 877.57 LBS SHEET 1 OF 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
1 2 14 1
D P P
2 D
D 1 1
1
10
4
DETAIL V
SECTION N-N
SCALE 1 : 8
SECTION K-K
SCALE 1 : 4 5 6 7 8
14 14 SECTION A-A
C C
SCALE 1 : 4
14
1 U
11 11
2
SECTION P-P
SCALE 1 : 8 1-3/4"
B B
DETAIL U
SCALE 1 : 2 2
1
2
1 2
SECTION F-F
SCALE 1 : 4
.001
PREMIUM
(0.002 IN DIAMETER, DRILLING EQUIPMENT AND SUPPORT
NORMINAL, PRESS FIT) SECTION T-T 10 12 TITLE:
A SCALE 1 : 16 ASSEMBLY, MOUNT FRAME A
TORQUE ATTREST SYSTEM
GDM 750T, 66"
13
DETAIL D
SCALE 2 : 1 SECTION H-H B A800052 2
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 M800373 ROD STOP CLAMP, CYLINDER, EXTEND FRAME, GDM 750T 1

2.008 4"
D D
3 026211.0828DH2 CAPSCREW,SOCKET HEAD, 1/2-13UNC X 1.75, DH2 4
1 2 3
1
C C
SECTION A-A
SCALE 1 : 1.5
3
1 2 3
B B
A
3"

PREMIUM
TOLERANCES:
A A
ONE PLACE DECIMAL .031 APPR. ROD STOP ASSEMBLY A
CYLINDER
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION EXTEND FRAME, GDM 750T
B A800055
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 M106061 J-BOX, EXTEND FRAME 1
2 E100121 STRAIN RELIEF, 1/2 NPT, 0.375 - 0.500 2
3 E100147 SEALING RING, 1/2 NPT 2
D D
4 E100130 STRAIN RELIEF, 3/4 NPT, 0.750 - 0.880 1
1 5 E100157 SEALING RING, 3/4 NPT 1
6 7 E100237 LOCKNUT, CONDUIT FTG, 3/4 NPT 1
8 E500272 DIN RAIL, TS35 (4-1/2" LENGTH) 4-1/2"
A 9 E103733 END STOP, GREY 2
10 E500228 TERMINAL BLOCK, DIN, FEED THRU, SCREW; 26-10AWG, 30A, 600V 9
7 6 11 E101072 TERMINAL, GROUND, DUAL LEVEL, 1
A 12 220102.0400 WASHER, LOCK, NORDLOCK, 1 PAIR 1/4 4
13 008121.0408DH CAPSCREW, HEX HEAD, 1/4-20 X 0.50, DH, GR8 4
C C
14 201311.01000 WASHER, FLAT, SS, #10 2
5 15 210202.01000 WASHER, LOCK, SS, #10, FOR #10-32 SCREW 2
16 026211.01204 SOCKET HEAD SCREW, #10-32, 1/4" LG, ALLOY STEEL 2
17 E103657 CABLE, 10 C #16 AWG, 600V, GENERIC 40 FT
4 2 3 2 3
NOTE: ITEM 17 IS NOT SHOWN IN VIEWS
B B
11
4-1/2"
9X 10
SECTION A-A
SCALE 1 : 1.5
9 14 15 16
PREMIUM
DIMENSIONS ARE IN INCHES DRAWN KHW 7/15/15 DRILLING EQUIPMENT AND SUPPORT
8 TOLERANCES:
A
ONE PLACE DECIMAL .031 APPR. KIT, ELECTRICAL A
12 13 TWO PLACE DECIMAL .015
EXTEND FRAME
THIRD ANGLE
B A500684
2 REVISE BOM, REPLACE DRAWING TEMPLATE, ETC. 5/27/2022 DS
2
FINISH
01 RELEASE FOR MANUFACTURE 7/15/2015 125 Ra UNLESS NOTED OTHERWISE
REV. DESCRIPTION DATE ISSUED ECN # PROHIBITED. DO NOT SCALE DRAWING WEIGHT: LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 M106762 TAP 1/4" FNPT, ELBOW, #8 MORB X #8 MORFS 1
2 M106761 DRILL 1/8" ORIFICE HOLE, 1/4" NPT PLUG, HEX DRIVE 1
D 2 1 A D
(#8 ORB)
1/8"
1 2
C C
2 1
B 1 B
SECTION A-A
SCALE 2 : 1 (#8 ORFS)

PREMIUM
2 TOLERANCES:
FRACTIONAL 1/16 CHECKED JP 26AUG2022 TITLE:
A
ONE PLACE DECIMAL .031 APPR. 1/8" ORIFICE INSERT A
EXTEND FRAME FITTING
THIRD ANGLE
B A100248
1
FINISH
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

NO.
1 H107042 3:1 Pilot Ratio, Dual Counter Balance Valve Assembly, 15 GPM 1
2 H100619 ADAPTER, MALE 1/2 JIC, MALE 1/2 ORB 2

D D
2 3 H101001 ADAPTER, MALE 1/2 ORFS, MALE 1/2 ORB 2
2 4 H106527 #8 F-ORFS-SWL X #8 M-ORFS X #8 M-ORFS 2

5 026211.0532DH CAPSCREW, SOCKET HEAD, 5/16-18UNC X 2.00, DH 2
A 6 230101.0500 WASHER, LOCK, HI COLLAR 5/16 2
2 1 2 2 2
2 2 2
1 3 2 4 4 3 5 6 3 2
C C
7-3/4"
3
3 2
3 3 2
2 2
B 4 4 B
4
2 2
2
4
2
A 2-5/16"
2 5 3 4 4 2 1
SECTION A-A
SCALE 1 : 2 2 2 2

PREMIUM
TOLERANCES:
A 5 6
ONE PLACE DECIMAL .031 APPR. ASSEMBLY A
6-1/16" TWO PLACE DECIMAL .015
COUNTER BALANCE VALVE & FITTINGS
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION EXTEND FRAME, 750T
REVISIONS SIZE PART/DWG NO. REV
B A800054
2
FINISH
2 CHANGE FITTINGS 04AUG2022 JP PROHIBITED. DO NOT SCALE DRAWING WEIGHT: 5.53 LBS SHEET 1 OF 1
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1

7 8 1 E107011 LIMIT SWITCH 1
2 M105393 LIMIT SWITCH BRACKET, EXTEND 1

FRAME
3 E107012 LIMIT SWITCH, FLEXIBLE METAL 1
D ADAPTER D
4 201311.01000 WASHER, FLAT, SS, #10 8
5 CAPSCREW, HEX SOC HD, # 10-

2 026211.01044DH 24UNC x 2.75 DH 2
1 6 CAPSCREW, HEX SOC HD, # 10-

2 026211.01056DH 24UNC x 3.50 DH 2
7 210202.0400 WASHER,LOCK,SPLIT,GR8, 1/4" 4
8 026211.0412DH CAPSCREW,SOCKET HEAD, 1/4- 4

20UNC X 0.75, DH
9 126112.01024 NUT, SELF LOCKING, 10-24 4
C
11 026211.0812DH2 CAPSCREW,SOCKET HEAD, 1/2- 2 C
13UNC X 0.75, DH2
4 5
3
3 5 4
6 4
B B
10 11 6 4
4 9 8 7 UNLESS OTHERWISE SPECIFIED: NAME DATE

PREMIUM
DIMENSIONS ARE IN INCHES DRAWN DGW 9/2/15 DRILLING EQUIPMENT AND SUPPORT
TOLERANCES:
A
LIMIT SWITCH A
ASSEMBLY
THIRD ANGLE
INTERPRET GEOMETRIC PROJECTION EXTEND FRAME
B A101899
2 CORRECT ITEM 5 & 6 P/N VERSUS LENGTH, AND REPLACE DRAWING TEMPLATE 5/25/2022 DS
2
FINISH
1 RELEASE FOR MANUFACTURING 9/3/2015 DGW 125 Ra UNLESS NOTED OTHERWISE
8 7 6 5 4 3 2 1
Electrical Schematics
500
501 TOPDRIVE
AUX J-BOX
502
TB90
503 PIN 1 BLACK CAB 48
1
504 LOCAL BLOWER
PIN 2 WHITE 15 HP
505 2
3550 RPM
506 PIN 3 RED
3 13.8 Amp
507 480VAC
PIN 4 GREEN
508 4
509 PIN 5 ORANGE CAB 49
5
510 LUBE PUMP
PIN 6 BLUE
511 6 2 HP
512 PIN 7 WHT-BLK 1750 RPM
7 2.7 Amp
513 480VAC
PIN 8 RED-BLK
514 8
515 PIN 9 GRN-BLK SPARE
9
516
AUX PIGTAIL PIN 10 ORN-BLK SPARE
517 10
KEYED 00
518 PIN 11 BLU-BLK SPARE
11
519
PIN 12 BLK-WHT SPARE
520 12
521 PIN 13 RED-WHT
13 MOTOR
522
523 PIN 14 GRN-WHT HEATER
14
524 PIN 15 BLU-WHT
15 LUBE
525
526 PIN 16 BLK-RED HEATER
16
527 PIN 17 WHT-RED SPARE
17
528
PIN 18 ORN-RED SPARE
529 18
530 PIN 19 BLU-RED
19
531
532
533
534
535
536
537
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
TD PLC BOX
1715 TD TB2
PIN A 800 1 800 +VDC RED
1716
1717 PIN B 801 801 0VDC BLACK
2
1718
1719 3
1720 PIN D 802 4 802 A YELLOW

ENCODER PIGTAIL CHANNEL A
1721 KEYED 00
PIN E 803 5 803 A/ YELLOW/WHITE
1722 TD ENCODER
CAB 33
1723 6
1724 PIN G B
804 7 804 BLUE
1725 CHANNEL B
PIN H 805 8 805 B/ BLUE/WHITE
1726
1727
9
1728
10
1729
1730
1731
1732
1733
1734
1735
NOTE:
1736 ***SHIELDS TO BE GROUNDED AT VFD***
1737
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811 TD PLC J-BOX
1812 D1 TB30
PIN 1 BLACK 1
788
TD R1 13
1813 1 I-0.0
PIN 2 WHITE
1814
D2
1815 2 789
TD R1 13
1816 2 I-0.1
PIN 3 RED 3
1817
4
24 VDC
1818 PIN 4 GREEN
1819 5
1820 6
1821
1822 PLC PIGTAIL 7
KEYED 01
1823
PIN 5 ORANGE 8
1824
9 0 VDC
1825 PIN 6 BLUE
1826 10
PIN 7 WHT-BLK
1827
1828 PIN 8 RED-BLK
1829
PIN 9 GRN-BLK
1830
1831 PIN 10 ORN-BLK
1832
1833
1834
1835
1836
1837
1838
MODULE #1 MODULE #2 MODULE #3 MODULE #4 MODULE #5 MODULE #6 MODULE #7
2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC
1900 RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE
1901
1902
ETHERNET
1903 24V 0V DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2
1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5
HNDLR ROTATE HNDLR ROTATE LINK TILT LINK TILT LINK TILT SPARE
1904 FORWARD REVERSE HNDLR UNLOCK STAND JUMP IBOP CLOSE IBOP OPEN BUW CLOSE BUW OPEN EXTEND RETRACT FLOAT Q13.1 BRAKE BRAKE DUMP
Q8.0 Q8.1 Q9.0 Q9.1 Q10.0 Q10.1 Q11.0 Q11.1 Q12.0 Q12.1 Q13.0 Q14.0 Q14.1
320 322 334 316 314 312 310 308 326 328 324 304 306
1905
1906
+ + 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V
1907 2 6 2 6 2 6 2 6 2 6 2 6 2 6 2 6
1908
1909
1910 - - 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V 0V
3 7 3 7 3 7 3 7 3 7 3 7 3 7 3 7
1911
321 323 335 317 315 313 311 309 327 329 325 305 307
1912
1913
PE PE PE PE PE PE PE PE PE PE PE PE PE PE PE PE
1914 4 8 4 8 4 8 4 8 4 8 4 8 4 8 4 8
1915
1916
1917
WAGO 750-375 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508
1918
1919 TB30:7
0V MODULE #8 MODULE #9 MODULE #10 MODULE #11 MODULE #12 MODULE #13 MODULE #14
24V 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 2-DO 24V DC 16-DI 24V DC 4-AI 4-20mA
TB30:1 RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE
1920 DI1 DI2
1 2
1921 24V POWER 24V POWER
SUPPLY #1 SUPPLY #2
363 366
1922
DI3 DI4
DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2 DO1 DO2 AI1 AI2
3 4
1923 1 5 1 5 1 5 1 5 1 5 PH LOCK 1 5
ELEVATOR ELEVATOR ELEVATOR ELEVATOR DOLLY DOLLY SPARE SENSOR
SPARE SPARE DOWN UP OPEN CLOSE EXTEND RETRACT SPARE SPARE SPARE SPARE
1924 Q15.0 Q15.1 Q16.0 Q16.1 Q17.0 Q17.1 Q18.0 Q18.1 Q19.0 Q19.1 355
334 336 330 332 338 340
DI5 DI6
1925 5 6
DOLLY EXTEND NO WEIGHT
SWITCH PROX SWITCH
1926 24V 24V 24V 24V 24V 24V 24V 24V 24V 24V 377 375 M M
2 6 2 6 2 6 2 6 2 6 DI7 DI8 2 6
1927 7 8
ELEVATOR CLOSE HAS WEIGHT
SENSOR PROX SWITCH
1928
378 376
DI9 DI10
1929
9 10
0V 0V 0V 0V 0V 0V 0V 0V 0V 0V ELEVATOR LOAD AI3 AI4
1930 3 7 3 7 3 7 3 7 3 7
SPARE SENSOR
3 7
379 HYDRAULIC
DI11 DI12 SPARE SYS PRESS
1931
335 337 331 333 339 341 11 12 409
1932 SPARE SPARE
1933 PE PE PE PE PE PE PE PE PE PE DI13 DI14 M M
4 8 4 8 4 8 4 8 4 8 13 14 4 8
1934 SPARE SPARE
0V
1935 DI15 DI16
15 16
1936
SPARE SPARE
1937
WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 753-508 WAGO 750-1405 WAGO 753-455
1938
1939
1940
1941
MODULE #15 MODULE #16 MODULE #17 MODULE #18 MODULE #19 MODULE #20
4-AI 4-20mA 4-AI 4-20mA 2/4 CHANNEL RTD 2/4 CHANNEL RTD INCREMENTAL ENCODER INTERFACE END MODULE
RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE RACK 1 TOP-DRIVE
AI1 AI2 AI1 AI2 AI1 AI2 AI1 AI2 A A/ 24V 0V
1 5 1 5 1 5 1 5 1 5 1 5
HYD RETURN VIBRATION LUBE OIL MOTOR MOTOR
PRESS HYD TEMP SENSOR SPARE TEMP RTD 1 RTD 3
411 407 450 432 417 423
100Ω
M M M M M M M M B B/ N1 N2
2 6 2 6 2 6 2 6 2 6 2 6
431 418 424
AI3 AI4 AI3 AI4 AI3 AI4 AI3 AI4 C C/ LTCH GATE
3 7 3 7 3 7 3 7 3 7 3 7
LUBE PRESS LUBE PRESS AMBIENT MOTOR
AFTER FILTER B4 FILTER SPARE SPARE TEMP RTD 2
405 403 429 420
100Ω 100Ω
M M M M M M M M 5V 0V REF SHLD
4 8 4 8 4 8 4 8 4 8 4 8
0V 0V
428 421
WAGO 753-455 WAGO 753-455 WAGO 750-464 WAGO 750-464 WAGO 750-637 WAGO 750-600
TOPDRIVE
TD PLC J-BOX
TD R1 M15 CH1
407 WHITE
- 5 SIGNAL -
HYDRAULIC PT1
TEMPERATURE 408 BROWN 24V
+ TB30:3
GND1
TD R1 M14 CH3
409 BLK
HYDRAULIC - 7 SIGNAL -
SYSTEM PT3 410 RED 24V
PRESSURE + TB30:3
GND1
TD R1 M15 CH0
411 BLK
HYDRAULIC - 1 SIGNAL -
RETURN PT4 412 RED 24V
PRESSURE + TB30:3
GND1
TOP DRIVE
GEARCASE PLC JBOX
TD R1 M17 CH 0
WHT CAB 76 432 WHT
1 MEAS LEAD (-)
LUBE OIL
TEMP
RED 431 RED
RTD7 2 MEAS LEAD (+)
RED 433
TD R1 M15 CH3
403 BLK
LUBE PRESS - 7 SIGNAL -
BEFORE PT1 404 RED 24V
FILTER + TB30:4
GND2
TD R1 M15 CH2
405 BLK
LUBE PRESS - 3 SIGNAL -
AFTER PT2 406 RED 24V
FILTER + TB30:4
GND3
PLC J-BOX TRACTION MOTOR
TD R1 M18 CH0 WHT

417
+AI 1 1
WHT
A
TD R1 M18 CH0 RTD
418 RED
-AI 1 2
WHT
WHT
SPARE
RTD
RED
TD R1 M18 CH1 WHT

420
+AI 3 3
WHT
B
TD R1 M18 CH1 RTD2
421 RED
-AI 3 4
WHT
WHT
SPARE
RTD
RED
TD R1 M18 CH2 WHT

423
+AI 2 5
WHT
C
TD R1 M18 CH2 RTD2
424 RED
-AI 2 6
WHT
WHT
SPARE
RTD
RED
TOPDRIVE TOPDRIVE
PLC J-BOX PLC J-BOX
LINK TILT RETRACT ELEVATOR UP

TD R1 M5 SOL04B TD R1 M9
320 BLACK 2-H 336 BLACK 2-H
O-0.1 5 O-0.1 5 + -
+ -
321 WHITE 337 WHITE
O-0.1 7 O-0.1 7
GREEN GREEN
LINK TILT EXTEND ELEVATOR DOWN

SOL04A TD R1 M9
TD R1 M5
O-0.0 1 O-0.0 1 + -
+ -
327 WHITE 335 WHITE
O-0.0 3 O-0.0 3 TOPDRIVE
GREEN GREEN
PLC J-BOX
LINK TILT FLOAT ELEVATOR CLOSE
TD R1 M6 SOL05A TD R1 M10 DOLLY RETRACT
O-0.0 1 O-0.1 5 + - TD R1 M11
+ -
325 WHITE 333 WHITE 340 BLACK 2-H
O-0.0 3 O-0.1 7 O-0.1 5 + -
GREEN GREEN 341 WHITE
O-0.1 7
GREEN
HANDLER UNLOCK ELEVATOR OPEN
SOL02B TD R1 M10
TD R1 M2 DOLLY EXTEND
O-0.0 1 O-0.0 1 + - TD R1 M11
+ -
O-0.0 3 O-0.0 3 O-0.0 1 + -
O-0.0 3
GREEN
HANDLER ROTATE FWD BRAKE CLOSE
SOL03A SOL01B
TD R1 M1 TD R1 M7
STAND jUMP
SOL06B
O-0.0 1 O-0.0 1 + - TD R1 M2
+ -
O-0.0 3 O-0.0 3 O-0.1 5 + -
O-0.1 7
GREEN
HANDLER ROTATE REV BRAKE DUMP
SOL03B TD R1 M7 SOL01C
TD R1 M1
O-0.1 5 O-0.1 5 + -
+ -
323 WHITE 307 WHITE
O-0.1 7 O-0.1 7
GREEN GREEN
BUW GRIPPER OPEN IBOP OPEN

SOL08A SOL07B
TD R1 M4 TD R1 M3
O-0.1 5 O-0.1 5 + -
+ -
309 WHITE 313 WHITE
O-0.1 7 O-0.1 7
GREEN GREEN
BUW GRIPPER CLOSE IBOP CLOSE

SOL08B SOL07B
TD R1 M4 TD R1 M3
O-0.0 1 -
O-0.0 1 + -
+
311 WHITE 315 WHITE
O-0.0 3 O-0.0 3
GREEN GREEN
TOP DRIVE
PLC JBOX TOP DRIVE
WEIGHT SENSOR ELEVATOR CLOSE

TD R1 M13 PLC JBOX
376 LIMIT SWITCH SWITCH
HAS WEIGHT I-0.5 8
GRN TD R1 M13 GRN
WHT BLK ELEVATOR CLOSE 393 BLU BRN
TD R1 M13 SENSOR I-0.6 7
375 RED BLK
NO WEIGHT I-0.5 6
TB1:4 377 24V 394 24V

TB1:4
TB1:7
TOP DRIVE TOP DRIVE
PLC JBOX ELEVATOR LOAD

HANDLER LOCK SENSOR PLC JBOX
SWITCH
4 355 PROX
STATUS I-0.3
TD R1 M13 GRN
356 0V ELEVATOR LOAD 395 BLU BRN
TB01:8 SENSOR I-0.9 10
BLK BRN BLK
TB1:5 354 24V
BLU 396 24V

TB1:4
TOP DRIVE
PLC JBOX
TOP DRIVE
VIBRATION SENSOR
TD R1 M16
1 391 - DOLLY EXTEND
STATUS I-0.0 PLC JBOX
SWITCH
V
390 24V TD R1 M13 GRN
TB1:5 + DOLLY EXTEND 397 WHITE BLK
SENSOR I-0.4 5
TB1:4 398 24V

500
501 TOPDRIVE
502 DOLLY EXTEND
503 SWITCH
504
DOLLY J-BOX GRN
505 PLC J-BOX WHITE BLK
506
507
508 TD R1 M13 TB90
DOLLY EXTEND 397 BLACK
509 SENSOR I-0.4 5 1
510 398 24V WHITE 2
TB1:4
511
RED
512 3
TD R1 M11
513 340 GREEN
O-0.1 5 4
514 DOLLY RETRACT
341 ORANGE DOLLY RETRACT
515 O-0.1 7 5
516 BLUE BLACK 2-H
6 + -
517 TD R1 M11 WHITE
338 WHT-BLK
518 O-0.0 1 7 GREEN
519 DOLLY EXTEND RED-BLK
O-0.0 3 339 8
520 DOLLY EXTEND
GRN-BLK
521 9
BLACK 2-H
522 ORN-BLK + -
10 WHITE
523
524 GREEN
525
526
527
528
529
530
531
532
533
534
535
536
537
Hydraulic Schematics
TOP DRIVE BRAKE HANDLER LOCK HANDLER ROTATE LINK TILT LINK TILT FLOAT SPARE STAND JUMP IBOP SPARE SPARE BACK-UP WRENCH SPARE SPARE
"A" "B" "C" "D" "E" "F" "G" "H" "I" "J" "K" "L" "M"
P A P A P A P A P A P A P A P A
T B T B T B T B T B T B T B T B
1 mm
"32H"
1000 1500
"34G B" PSI PSI
"30C B" "30C A" "30D B" "30D A" "34G A" 1500 2250
1400 1400 PSI
PSI PSI
PSI "25I A" "25J A"
"33B" "33A" 2500 2500 1000 "30G" "22H" 600 1800
1300 1000 PSI PSI PSI PSI PSI
PSI PSI "25G A" 1500
"20C" "25E A" "20I" PSI "20K"
1500 "25G B"
"36D A" 2750 PSI 800
"36D B" PSI "20F" 1700 PSI "25J B" "20L"
"20A" "20B" 1200 PSI "20M"
PSI
"25E B"
"20G"
"20H"
"22D" "32D" "30J" "30J"
"P"
#10
"T"
#10
"B1" "A1" "B2" "A2" "B3" "A3" "B4" "A4" "B5" "A5" "B6" "A6" "A7" "B8" "A8" "B9" "A9" "B10" "A10" "B11" "A11" "B12" "A12" "B13" "A13"
#8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8 #8
"GB1" "GA1" "GB2" "GA2" "GB3" "GA3" "GB4" "GA4" "GB5" "GA5" "GB6" "GA6" "GA7" "GB8" "GA8" "GB9" "GA9" "GB10" "GA10" "GB11" "GA11" "GB12" "GA12" "GB13" "GA13"
#4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4 #4
15 14
1000 1000
PSI PSI
9 8
VR VP
750 PSI
2
3
1
CNCC
1 2
CODA
BORE : 4.00"
4 3 ROD : 1.75"
STROKE : 12.00"
2 B A
2 1
2 3
1
BORE : 10.00" "T"
3 ROD : 8.00" #12
1 BORE : 2.50"
STROKE : 2.00" FROM HPU
B4
ROD : 1.38" "P"
STROKE : 2.50" #12
3 BORE : 1.50"
2
4
B5
ROD : .625" B A
STROKE : 3.50" A4
A5
1 3
2 1
T B
P A
DUMP TO TANK
P T P T S1
S6
S2
ELEVATOR TILT MANIFOLD AMP CONTROL UNIT
S3
S7 C1/X S4
BORE : 3.25" C1 C2 X A B C
ROD : 1.75"
STROKE : 13.50" TOP DRIVE EXTEND FRAME
TOP DRIVE BRAKE CALIPERS
- 01 BY - THIS PRINT DESIGN AND DETAIL ARE DRAWN JP 08/10/2022
02 - BY -
THE SOLEPROPERTY AND INVENTION CHECKED - - PREMIUM OILFIELD 9841 WINDMILL PARK LN
OF PREMIUM DRILLING EQUIPMENT APPRV'D - - HOUSTON, TX 77064
AND SUPPORT. THIS PRINT IS ISSUED DRILLING EQUIPMENT AND SUPPORT
03 - BY - WITH THE UNDERSTANDING THAT IT PLOTTED
MATERIAL
04 - BY - IS NOT TO BE REPRODUCED WITHOUT
WRITTENCONSENT FROM PREMIUM
SCHEMATIC, HYDRAULIC,
05 - BY - DRILLINGEQUIPMENT AND SUPPORT
AND RETURNEDUPON REQUEST.
GDM 750 TON W/ELEVATORS
EST. WEIGHT SCALE
No. M/D/Y BY - NTS H102549-750 REV-01
- 01 2011/12/7 JA RELEASE THIS PRINT DESIGN AND DETAIL ARE DRAWN JP 2022/09/02
THE SOLE PROPERTY AND INVENTION CHECKED DS 2022/09/03 9841 WINDMILL PARK RD
02 2013/5/20 KS ADDED NEW FILTER NUMBER OF GDS INTERNATIONAL. THIS PRINT HOUSTON, TX 77064
APPRV'D
IS ISSUEDWITH THE UNDERSTANDING
03 - - - THAT IT IS NOT TO BE REPRODUCED PLOTTED
WITHOUT WRITTEN CONSENT FROM MATERIAL
04 - - -
GDS INTERNATIONAL AND RETURNED
UPON REQUEST.
LUBE SCHEMATIC
05 - BY -
EST. WEIGHT SCALE
No. Y/M/D BY - REV-02
1"=1"
A
1/8"
1/2" B
1/2"
1/2"
A
1/2"
1/2"
1/8"
1/2"
1/2" 1/2"
2 1
3/4"
3/4" 3
3/8"
A 08/09/2022 JP FOR_REFERENCE_ONLY THIS PRINT DESIGN AND DETAIL ARE DRAWN JP 08/09/2022
-
THE SOLEPROPERTY AND INVENTION CHECKED JP 08/09/2022 PREMIUM OILFIELD
01 BY - OF PREMIUM DRILLING EQUIPMENT AN APPRV'D DRILLING EQUIPMENT AND SUPPORT
D SUPPORT.THIS PRINT IS ISSUED
02 - BY - WITH THE UNDERSTANDING THAT IT PLOTTED
IS NOT TOBE REPRODUCED WITHOUT MATERIAL
03 - BY -
WRITTENCONSENT FROM PREMIUM SCHEMATIC, HYDRAULIC
04 - BY - DRILLINGEQUIPMENT AND SUPPORT
AND RETURNEDUPON REQUEST.
EXTEND FRAME
EST. WEIGHT SCALE
No. Y/M/D BY - REV-A
1"=1"
SW
CAD
PLC Pressure HPU Tank PLC
Signal „Elevator Open“

S1
P T P T
Signal „Rotate up“ S6 S2 Signal „Elevator Close“
Elevator Tilt Manifold AMP Control Unit
Signal „Rotate down“ S7 S3
C1/X Feedback „Elevator Closed “
C1 C2 X A B C
S4
Feedback „ Load Sensor Activated “
Swivel Swivel
P Pressure Supply C1 C2
T Tank / Return
A Elevator Close
B Elevator Open
C Feedback Closed /Load Sensor
FL
A/P
FL Float Signal Pilot Line B/T
C/XP
C1 Rotate Up
C2 Rotate Down
*Hydraulic and electrical connections above the swivel are not included
X Float Signal Pilot Port **Control Units are optional available. Different types on request
Material Scale 1:1 Format A3 Weight kg

day name part name
Tolerance Surface drawn 16.11.2017 A. Rehfeld Interface drawing
ch.no engineering change day name DIN ISO DIN ISO check.
1302 norm
for AMP
The present document is the property of Elevator / Rotator Manifold
FORUM B + V Oil Tools GmbH part no. sheet
Oil Tools GmbH 1
Hamburg-Germany
corresponding authorisation has been previously
AUTHORIZED MANUFACTURER
1 sh.
GDM 850 - DRILLMEC
Itemized Spare Parts List
The main components of the GDM are generally not considered field-replaceable by design. The
maintenance practices and schedules defined in this section of the Operations & Maintenance Manual, are
meant to keep the main top drive components in working condition until major overhaul and refurbishment
periods are scheduled out of the field.
Therefore, the only spare parts Premium recommends are consumables that consist of fasteners, seals, o-
rings, wiring, fuses, safety wire, and a motor coupling repair kit. Additionally, because these spares are
consumables, they are normally readily available to the customer through many outlets and often already
kept on-site. Depending upon the consumables stocking philosophy of the end user, Premium can
customize consumables kits that are tailored to the customers’ specific needs.
The following kits are examples of recommended spares for

GDM Top Drives orders:
Extended Frame Spares: :

1. Rail Slider - M800307
2. Adjuster Bolt - M500398
3. Adjuster Clamp - M500399
4. Mounting Bolts -
• 026211.16 102dh2
• 02611.16.92dh2
5. Limit Switch - E107011
6. Limit Switch Flexible Adapter – E107012
Clamping Cylinder:
1. Wiper – S100365
2. Piston Seal – S100363
3. Rod Seal – S100364
4. Die Block – A100110
5. Die – R100080
IBOP:
1. Cranks – M102478
2. Cam Followers – M100613
3. Po Check Valve – H107216
4. IBOP Cylinder Seal Kit – H101325-2
5. IBOP Cylinder - H101325
GDM850- DRILLMEC Rev.4 3-71

GDM 850 - DRILLMEC
Hydraulic System:
1. Link Tilt Cylinder – A100246
2. Cylinder - H800030
3. Stucci Hydraulic Quick Connects –
• H500026
• H500027
• H500054
• H500066
• H500163
• H500163-1
4. Directional Valves –
• H500099
• H101341
• H101342
5. Filter – H102971
6. O-Rings for Filter Housing–
• S100484
• M101201
7. Gauges –
• 1K PSI – N500005
• 3K PSI – N500006
8. Stand Jump Circuit Cylinder –
• H800000
• Seal Kit - H800000-1
Brakes:
1. Caliper Seal kit –S101565
2. Brake Pads – M102872
3. Brake Valve – H500102
Lube System:
1. Filter – H100480
2. Gauge – 0-300 PSI N500004
3. Transducer – N100476
4. Lube Temperature RTD –E104323
5. Sight Glass and Gasket –
• M800138
• M800137
6. Lube Pump – H500024
7. Coupling and Insert –
• M100113
• M100114
3-72
G D M 8 5 0 - DRILLMEC
4
Section
Dropped Objects Manual

Contents
750/850 TON GDM TOP 4-2
DRIVES
4-1
DROPPED OBJECTS MANUAL
750/850 TON GDM TOP DRIVES
Issue Date: November 2015
The Dropped Objects Manual has been developed to provide information about components
on overhead equipment manufactured by Premium. This information will apply to Top Drive, Traveling
Block, Block Dolly and/or Torque Track parts that have potential to loosen and fall to the rig floor,
possibly causing injury or damage.
This manual includes various techniques of fastening with specifications as well as guidelines and
examples of general usage.
Contact:
Service Manager
Premium Oilfield
Drilling Equipment and Support,
LLC 9841 Windmill Park Ln.
Houston, TX 77064
+1 713 623-1449
Table of Contents
1 Introduction……………………………………………………...…Page 1
Dropped Objects Defined
Dropped Object Scenarios
Safety Requirements
General Safety Practices
Personnel and Equipment Service
2 Methods and Premium Guidelines for Retention……………………Page 4

Primary Retention
Secondary Retention
Safety Securing
Fastener Installation Guidelines
Safety Wire
Pin Retention
Notes
3 Fastener Specifications…………………………………………...Page 8
Hex Cap Screw
Socket-Head Cap Crew
Stud
Loctite
Pin
Flat Washer
Split Lock Washer
Hi Collar Split Lock Washer
Internal Lock Washer
External Lock Washer
Tab Lock Washer
Wedge Lock Washer
Hex Nut
Metal Lock Nut
Slotted Nut
Jam Nut
Cotter Pin
Multi-Jackbolt Tensioner
Retaining Ring
Safety Wire
Safety Cable
Table of Contents
4 GDM Top Drive General Assemblies…………………………………Page 29
GDM Top Drive General Assemblies Chart
Top Drive Dropped Objects Location Identification
1.1 Gearbox Assembly
1.2 Assy, Link, Top Drive, GDM
1.2.1 Link Collar Assembly
1.2.2 Rotating Plate Assy, Links Assy
1.2.3 Load Collar Front Brkt Assy, Top Drive Assy
1.2.4 Service Plate Assy, Top Drive Assy
1.2.5 Pinion Assy, Service Plate Assy
1.3 Bonnet/Motor Mount Assembly
1.4 Assy, Hydraulic, GDM
1.5 Lube System, GDM
2 Assy, Motor, GDM
2.1 Brake Valve Assembly
2.2 Hydraulic & Lube Manifold Assembly
2.3 Assy, Motor, Disc Brake
2.4 Assy, Blower
3 Guard Assembly
4 BUW Assy, GDM
4.1 Grabber Spring Stabilizer Assembly
4.2 Grabber Box Assembly
5 Block Interface Assembly, With Side Plates
5.1 Block Interface Assy
6 Service Loop Mount Assembly, TD Side, GDM
7 Assy, Gooseneck
8 Assy, Slider Frame, Offset
9 Lower Well Control Valve Actuator
10 Service Loops
11 Traveling Block / Block Interface
12 Torque Reaction Assemblies
13 Track Assembly
14 Crown Interface
15 Extend / Retract Frames
5 Ordering Replacement Parts…………………………………...…… Page 103
6 Revision Notice……………………………….……………...…..……Page 104

TITLE: Form:
349
PREMIUM DROPPED OBJECTS REVISION 0
DATE Nov 2015
MANUAL PAGE 1 of 104
Section 1 – Introduction
Dropped Objects Defined

A dropped object is:
Any object, with the potential to cause death or injury, or damage to

equipment or the environment, that falls from its previous static
position under its own weight.
Dropped objects derive their capability for damage and harm from the conversion
of their potential energy to kinetic energy prior to impact.
Dropped or potential dropped objects can be further classified as either static or

dynamic.
Static dropped object - A static dropped object is a solid object, initially at rest,
that falls from its original position under its own weight. Examples of static
dropped objects include a nut dislodged in a rig derrick, or a fallen cable tray due
to corroded fastenings.
Dynamic dropped object - A dynamic dropped object is a solid object that

breaks free from its fastenings due to the applied force from the impact of some
other equipment or a moving object. An example of a dynamic dropped object
would be a stand of drill pipe falling across the derrick and hitting and breaking a
light resulting in the light falling to the rig floor.
Dropped Object Scenarios

 Hand tools used at heights or left behind after working at height
 Operations conducted at height
 Equipment mounted at a height that, following contact, vibration or

environmental conditions, could fall, e.g., piping, lights, cameras, rigging
gear, etc.
 Temporary equipment at height
 Personnel working on a level directly below the work site
 Lifting operations
Contacts: Service Manager Premium International LLC 9841 Windmill Park Lane Houston, Texas
77064 Telephone: 713-623-1449 Website: www.globaldrillingsupport.com
TITLE: Form:
349
DATE Nov 2015
Safety Requirements
It is essential that proper practices and procedures are followed to maintain safe
and reliable operation. These practices and procedures are defined in the
respective GDM manuals and are the recommended methods of performing
operations and maintenance.
Perform a Job Safety Analysis (JSA) before starting any tasks. It is important to
insure that all personnel are clear of the work area before performing dangerous
tasks.
Always wear basic Personal Protective Equipment (PPE) - hard hat, safety
glasses, and safety boots when working or using equipment. Secondary PPE
may be needed for certain tasks.
Insure you have read all warning and caution information provided for safe
operation.
General Safety Practices

The Premium equipment can require or contain one or more utilities,
such as electrical and hydraulic.
Prior to commencing any work:
1. Isolate energy sources. Verify with meters or functioning of equipment that this
has happened.
2. Never perform maintenance or repairs while the equipment is in operation.
3. Allow heated equipment to cool before performing maintenance or repairs.
4. Always conduct a JSA prior to starting any task. Always insure that personnel
and equipment safety are never jeopardized.
5. Always wear the proper protective equipment.
6. Never operate any equipment without proper training.
TITLE: Form:
349
DATE Nov 2015
7. Prior to disassembly of equipment, insure all components (such as cables,

hoses, etc.) are tagged and labeled. Failing to do so could create a further failure
on re-starting.
8. Service to the equipment may require the use of tools designed specifically for
that purpose. Premium recommends that only the right tool for the job be used.
Personnel Training and Equipment Service

All personnel performing work such as installation, operations, repair or
maintenance procedures on Premium equipment, or in the vicinity of the
equipment, must be trained on rig safety, tool operation, and maintenance to
ensure their safety.
If required, please contact the Premium Service Department or the

Training Department for more information in regards to equipment
operation and maintenance or personnel training.
TITLE: Form:
349
DATE Nov 2015
Section 2 - Methods and Premium Guidelines for

Retention
All components of Premium hoisting equipment are designed and
manufactured for prevention of potential dropped objects under the API 8C
Dropped Object international standards. It is our intent to insure that
damages from vibration, improper maintenance, corrosion, shock load, and
collision are reviewed and minimized or alleviated. This result is achieved
through design, the use of specialty fasteners, locking and safety wires on
fasteners and pins, guards, safety cables, and integrated barriers. Retention is
accomplished by one or more of the methods below.
Primary Retention
This is the primary method by which an item is installed or mounted and

secured to prevent the item falling. This includes bolted connections,
screws, pins, buckles, clips, and welds.
Secondary Retention
This is the engineered method for securing the primary retention to

prevent loss of clamping force or displacement of fastening components.
This includes lock washers, lock wire, and cotter pins.
Secondary Retention is also referred to as Second Barrier or Fail

Safe feature in some engineering descriptions.
Safety Securing
This is an additional engineered method applied to or around the item and

secured back to the main structure, and is designed to restrain the items
hould the primary retention fail. This includes cables, baskets, and slings.
TITLE: Form:
349
DATE Nov 2015
Fastener Installation Guidelines
Premium recommends the following guidelines when installing

fasteners:
1) All cap screws used must meet or exceed the ASME B1.1 -2003 (R2008)
specifications.
2) All cap screws are to be torqued to the values shown on the Premium
torque chart. Any deviation from the torque chart is noted on the service
manual drawings or in the assembly work orders.
3) All cap screws permanently installed are to be coated with LOCTITE

Threadlocker or equivalent following the manufacturer’s instructions for
the dimension of the cap screw. Always follow Premium or
LOCTITE recommendations regarding which Threadlocker to use based
on the size of cap screw.
4) Any cap screws or fasteners that require periodic loosening to facilitate

adjustment of components (e.g., slider rails, tool joint clamps, link tilt
clamps) should be coated with a copper-based anti-seize thread
compound.
5) Where a locknut is required, use only Grade C metal locking nuts or

equivalent. Note: Metal lock nuts are reusable, but should not be reused
more than two to three times. The use of anti-seize on the locknut is not
recommended. When in doubt, replace the nut.
6) All caps crews or fasteners requiring the use of Wedge Lock washers
must be torqued to the recommended Premium or washer
manufacturer’s specification.
7) Slotted nuts can used on threaded pins and cap screws that have a drilled
thread that will accept a cotter pin when the nut is installed. The cotter pin
must be opened sufficiently to prevent it from dislodging.
8) Tab lock washers are designed to lock in the slot of the jam nut. At a
minimum, one tab must be bent into place.
TITLE: Form:
349
DATE Nov 2015
Safety Wire
Safety wire is required:
1) Whenever a part is mounted to the underside of another part.
2) Whenever the part has the possibility to fall without being contained.
3) Whenever the part is in a high vibration area.
Safety wire is not required:
1) If the bolt is captive in such a way that even when loose, the bolt and/or
the part it retains cannot fall.
2) Where the style of fastener will not allow holes to be drilled (button, flat or
pan head bolts). Where possible, internal/external lock washers or wedge
lock washers should be used. If a lock washer cannot be used, LOCTITE
Threadlocker should be applied to threads.
Stainless steel lock wire (twisted per conventional standards) is typically used
where space will not allow use of wire rope.
Stainless steel wire rope:
1) The use of 1/16” diameter wire rope is recommended for fasteners and
wired bolts to prevent loosening. 1/16" wire rope can also serve as fall
restraint for small safety bolts or pins.
2) The use of 1/8" diameter wire rope is recommended as a fall restraint for
items up to 100 lbs.
3) The use of 3/16" diameter wire rope is recommended as a fall restraint for
items between 100 and 400 lbs.
4) Larger diameter wire rope is used as recommended by Premium

Engineering for heavier objects.
TITLE: Form:
349
DATE Nov 2015
Pin Retention
1) For pins up to and including 0.750” in diameter, use a safety pin 0.125” or
larger.
2) For pins .0750” to 1.375” diameter, use a minimum ¼" bolt and Stover nut.
3) For pins 1.5” and 4.00” diameter, use a minimum 3/8" bolt and Stover nut.
4) For pins 4.25” and 6.00” diameter, use a minimum 1/2" bolt and Stover
nut.
Notes
1) It is recommended that safety wire should not be used to lock more than
three cap screws at a time.
2) When using a wedge lock washer, a film of dry moly must be applied to
both sides of washer as well as the screw threads.
3) LOCTITE Threadlocker is not considered a substitute for safety wire.
4) Never install capscrews without lubrication, other than when using metal
locking nuts.
5) Leave only enough slack wire on pins and fasteners to allow pin removal.
6) It is important to not have excess safety cable when using. Extra length
could allow an object to break the cable as it falls.
7) Double lock nutting and double nutting is NOT recommended.
8) Dimpling of bolts as a means of safety retention is not recommended.
9) Slotted nuts should only be used on components not requiring a constant

clamping pressure.
10) Where there is a possibility of exposure to the sharp end of a cotter pin, it
should be wrapped fully around the nut.
TITLE: Form:
349
DATE Nov 2015
Section 3 - Fastener Specifications
Hex Cap Screw

Premium uses SAE Grade 8 hex cap screws that conform to ASME
standards for thread and dimension. A typically specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Socket-Head Cap Screw
Premium uses socket-head cap screws that conform to ASTM A574

and ASME standards for thread and dimension. A typical specification is
shown below.
TITLE: Form:
349
DATE Nov 2015
Stud
Premium uses studs that conform to ASME thread and dimension

standards and ASTM physical requirements standards. A typical specification
is shown below.
TITLE: Form:
349
DATE Nov 2015
LOCTITE
Premium uses LOCTITE Threadlocker as specified by the manufacturer
and/or Premium Engineering. Descriptions of the products from the
manufacturer are shown below.
TITLE: Form:
349
DATE Nov 2015
Pin
Premium uses the following guidelines for pins:
1) For pins up to and including 0.750” in diameter, use a safety pin 0.125” or
larger.
2) For pins .0750” to 1.375” diameter, use a minimum ¼" bolt and Stover nut.
3) For pins 1.5” and 4.00” diameter, use a minimum 3/8" bolt and Stover nut.
4) For pins 4.25” and 6.00” diameter, use a minimum 1/2" bolt and Stover
nut.
Flat Washer
Premium uses flat washers that conform to ASTM F436 and ASME
standards for dimension. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Split Lock Washer

Premium uses helical spring lock washers that conform to ASME
B18.21 for dimensional, physical properties, and test methods standards. A
typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Hi Collar Split Lock Washer
Premium uses hi collar split lock washers that conform to ASME

dimension standards. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Internal Lock Washer
Premium uses internal lock washers that conform to ASME dimension

standards and ASTM finish standards. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
External Lock Washer
Premium uses external lock washers that conform to ASME dimension

standards and ASTM finish standards. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Tab Lock Washer
Premium uses tab lock washers manufactured by MiSUMi.

Specifications from the manufacturer are shown below.
TITLE: Form:
349
DATE Nov 2015
Wedge Lock Washer

Premium uses HEICO-LOCK wedge lock washers. The
manufacturer’s description of the HEICO-LOCK is shown below.
TITLE: Form:
349
DATE Nov 2015
Hex Nut
Premium uses SAE Grade 8 hex nuts that conform to ASME

standards for thread and dimension. A typical specification is shown below.
TITLE: Form:
349
PPREMIUM DROPPED OBJECTS REVISION 0
DATE Nov 2015
Metal Lock Nut
Premium uses Stover metal lock nuts manufactured by Coburn-Myers

that conform to ASME B18.16.6 for dimensional, mechanical, and
performance requirements. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Slotted Nut
Premium uses SAE Grade 2 slotted nuts that conform to ASME thread
and dimension standards. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Jam Nut
Premium uses SAE Grade 2 jam nuts that conform to ASME thread
and dimension standards. A typical specification is shown below.
TITLE: Form:
349
DATE Nov 2015
Cotter Pin
Premium uses cotter pins that conform to ASME B18.8.1 standards.

Typical dimensions are shown below.
TITLE: Form:
349
DATE Nov 2015
Multi-Jackbolt Tensioner
Premium uses Superbolt multi-jackbolt tensioners manufactured by

Nord-Lock. Specifications from the manufacturer are shown below.
TITLE: Form:
349
DATE Nov 2015
Retaining Ring
Premium uses several types of retaining rings: housing and shaft

rings manufactured by Rotoclip, and light, medium and heavy duty
internal and external rings manufactured by Smalley. Typical
specifications from the manufacturers are shown below.
TITLE: Form:
349
DATE Nov 2015
TITLE: Form:
349
DATE Nov 2015
Safety Wire
Premium uses .041” and .051” stainless steel safety wire

manufactured by Malin. An installation guide and examples of proper safety
wire technique are shown below.
TITLE: Form:
349
DATE Nov 2015
Safety Cable
Premium uses 1/16”, 1/8”, and 3/16” 7X7 and 7X19 stainless steel aircraft
cable. Typical specifications are shown below.
TITLE: Form:
349
DATE Nov 2015
Section 4 - GDM Top Drive General Assemblies Chart

This chart lays out component assemblies that require Secondary Restraint
and/or Dropped Object. The chart is listed by assembly and model with revision
dates.
ASSEMBLY MODEL DATE
DESCRIPTION 375 500 650 750
TON TON TON TON
1. BASE, GDM TOP DRIVE
1.1. GEARBOX ASSY, GDM
1.2. ASSY, LINK, TOP DRIVE
1.2.1. LINK COLLAR ASSEMBLY
1.2.2. ROTATING PLATE ASSY, LINKS
ASSY
1.2.3. LOAD COLLAR FRONT BRKT ASSY,
TOP DRIVE LINK ASSY
1.2.4. SERVICE PLATE ASSY
1.2.5. PINION ASSY, SERVICE PLATE ASSY
1.3. BONNET/MOTOR MOUNT ASSEMBLY
1.4. ASSY, HYDRAULIC, GDM
1.5. LUBE SYSTEM, GDM
2. ASSY, MOTOR, GDM
2.1. BRAKE VALVE ASSEMBLY
2.2. HYDRAULIC & LUBE MANIFOLD
2.3. ASSY, MOTOR, DISC BRAKE
2.4. ASSY, BLOWER, 15HP
3. GUARD ASSEMBLY, GDM
4. BUW ASSY, GDM
4.1. GRABBER SPRING STABILIZER
ASSEMBLY
4.2. GRABBER BOX ASSEMBLY
5. BLOCK INTERFACE WITH SIDE PLATES
5.1. BLOCK INTERFACE ASSY
6. SERVICE LOOP MOUNT ASSEMBLY,
7. ASSY, GOOSENECK
8. ASSEMBLY, RAIL SLIDER
9. LOWER WELL ACTUATOR ASSEMBLY
10. SERVICE LOOP ASSEMBLY
11. TRAVELING BLOCK /BLOCK INTERFACE
12. TORQUE REACTION
13. TRACK ASSEMBLY
14. CROWN INTERFACE
15. EXTEND/ RETRACT FRAMES
TITLE: Form:
349
DATE Nov 2015
Top Drive Dropped Object Location Identification

This portion provides a detailed pictorial breakdown of the proper primary and
secondary retention used on the GDM top drive.
Please Note:
Drawings included are meant to show a reference only. The different models may
contain many different drawings and have different configurations. Where
configurations have large differences in appearance, other photographs maybe
included.
Notes:
1) File photos included are used to indicate where safety wire is required.
The fasteners in the photograph may not actually have safety wiring
installed.
2) Photographs may show more than 3 wires wired together. Per the
effective date of the worksheet, wiring to only 3 bolts per wire is the
recommendation.
TITLE: Form:
349
DATE Nov 2015
1.1 GEARBOX ASSEMBLY
FLANGE, SUCTION Primary Restraint

DRAIN Socket head Cap screw
Through bolts (6 bolts Dry Moly Lube
@ 2 places) torqued Secondary Restraint
and lock wired. Wedge Lock Washer
Safety Wire
FLANGE, IDLER GEARS, Primary Restraint

BOTTOM Hex head Cap screw
Bolts torqued and lock Dry Moly Lube
wired (15 bolts @ 2 Secondary Restraint
places) on gearbox. Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
FLANGE, QUILL, Primary Restraint

BOTTOM Hex head Cap screw
wired (10 bolts on Secondary Restraint
gearbox. Wedge Lock Washer
Safety Wire
FLANGE, IDLER GEARS, Primary Restraint

TOP Socket head Cap screw
places) on gearbox. Wedge Lock Washer
Safety Wire
FLANGE, TOP QUILL Primary Restraint

Bolts torqued and lock Hex head Cap screw
wired (12 bolts). Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
FLANGE, TOP QUILL Primary Restraint

Bolts torqued (8 bolts). Captive
Loctite
Secondary Restraint
Seal, Cage, Top
TITLE: Form:
349
DATE Nov 2015
FLANGE TOP QUILL, Socket head Cap screw

GEARBOX ASSY Loctite
Bolts torqued and lock Secondary Restraint
wired (3 bolts). Safety Wire
FLANGE, FILLER CAP (1 Primary Restraint

of 2) Socket head Cap screw
places) Wedge Lock Washer
Safety Wire
FLANGE, FILLER CAP Primary Restraint

(2 of 2) Socket head Cap screw
places). Wedge Lock Washer
Safety Wire
RING, SEALING, TOP Primary Restraint

DRIVE CORE Socket head Cap screw
Safety Wire
TITLE: Form:
349
DATE Nov 2015
GEARBOX LID (1 of 2) Primary Restraint

wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
GEARBOX LID (2 of 2) Primary Restraint

Bolts torqued and lock Socket head Cap screw
wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
VIEWCOVER WINDOW Primary Restraint

(1 OF 2) Hex head Cap screw
PLACES) Wedge Lock Washer
Safety Wire
VIEWCOVER WINDOW Primary Restraint

(1 OF 2) Socket head Cap screw
wired (@ 3 locations) Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
LUBE OIL RESERVOIR Primary Restraint

(1 OF 2) Socket head Cap screw
wired (@ 2 locations) Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.2 ASSY, LINK, TOP DRIVE, GDM
ROTATING PLATE Primary Restraint

wired (24 bolts). Flat Washer
Loctite
Secondary Restraint
Safety Wire
ELEVATOR LINK, Primary Restraint

ASSEMBLY Hex head Cap screw
nutted @ 2 places. All Metal Locking Nut
Safety Wire
TITLE: Form:
349
DATE Nov 2015

ASSEMBLY Captive one side
Retaining Ring Fully Secondary Restraint
Seated Internal Retaining Ring
Safety Wire
ELEVATOR LINK, PIN Primary Restraint

Bolts and lock nut Hex head Cap screw
torqued @ 2 places. Secondary Restraint
All Metal Locking Nut

Bolts and lock nutted Secondary Restraint
torqued @ 2 places. All Metal Locking Nut
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.2.1 LINK COLLAR ASSEMBLY
LINK COLLAR TOP Primary Restraint

PLATE Socket head Cap screw
wired (10 bolts) Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
LATCH LOAD COLLAR, Primary Restraint

LOAD COLLAR ASSY Eye Bolt 2
Eye bolts torqued to Loctite
specification. Secondary Restraint
Wedge Lock Washer
Safety Wire
Safety Securing
Stainless steel wire rope
Quick Link
ROTARY SEAL ASSY Primary Restraint

wired (12 bolts) Loctite
Secondary Restraint
Safety Wire
PLATE, GUIDE, ANTI- Primary Restraint

ROTATION Hex head Cap screw
wired (3 bolts) on Secondary Restraint
plate. Wedge Lock Washer
Safety Wire
SENSOR BRACKET Primary Restraint

wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
SENSOR BRACKET Primary Restraint

Bolts and locknuts Hex head Cap screw
torqued and lock wired Secondary Restraint
All Metal Locknut
Safety Wire
LATCH LOAD COLLAR, Primary Restraint

LOAD COLLAR ASSY Pin
Bolts torqued and lock Slotted Nut
wired (1 bolt @ 2 Secondary Restraint
places) Lynch Pin
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.2.2 ROTATING PLATE ASSY, LINKS ASSY
BRG, TURN TABLE, Primary Restraint

LINK ASSEMBLY Hex head Cap screw
wired Secondary Restraint
Wedge Lock Washer
Safety Wire
BRG, TURN TABLE, Primary Restraint

LINK ASSEMBLY Socket head Cap screw
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
CLAMP, DOUBLE Primary Restraint

wired (2 places) Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
File Photo 1
TITLE: Form:
349
DATE Nov 2015
1.2.3. LOAD COLLAR FRONT BRKT ASSY, TOP DRIVE LINK ASSY
LOAD COLLAR FRONT Primary Restraint

BRACKET Hex head Cap screw
Wedge Lock Washer
Safety Wire
LOAD COLLAR REAR Primary Restraint

ASSY, LINK ASSY Hex head Cap screw
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.2.4. SERVICE PLATE ASSY, TOP DRIVE ASSY
SERVICE PLATE Primary Restraint

MOUNTING BOLTS Socket head Cap screw
(1 of 2) Loctite
wired (16 bolts) High Collar Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
SERVICE PLATE Primary Restraint

(2 of 2) Loctite
wired (16 bolts) High Collar Lock Washer
Safety Wire
GDM HYDRAULIC Primary Restraint

RETURN MANIFOLD Socket head Cap screw
Bolts torqued and lock Loctite
High Collar Lock Washer
Safety Wire
LUBE FILTER ASSEMBLY Primary Restraint

(1 of 2) Socket head Cap screw
Safety Wire
LUBE FILTER ASSEMBLY Primary Restraint

(2 of 2) Hex head Cap screw
wired (3 bolts) All Metal Locking Nut
Safety Wire
TITLE: Form:
349
DATE Nov 2015
HANDLER LOCK Primary Restraint

wired (2 bolts) All Metal Locking Nut

(1 of 4) Secondary Restraint
Bolts torqued and lock All Metal Locking Nut
wired (4 bolts)

Bolts torqued and lock All Metal Locking Nut
wired (4 bolts)

ASSEMBLY Captive Pin
Retaining ring firmly set Retaining Ring
in place
TITLE: Form:
349
DATE Nov 2015

ASSEMBLY Captive Pin
(4 of 4)
TITLE: Form:
349
DATE Nov 2015
1.2.5. PINION ASSY, SERVICE PLATE ASSY
GEAR PLATE WLDMNT, Primary Restraint

PINION ASSY Socket head Cap screw
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
PINION MOTOR Primary Restraint

MOUNT Socket head Cap screw
Wedge Lock Washer
Safety Wire
MOTOR, HANDLER Primary Restraint

ROTATE Socket head Cap screw
Wedge Lock Washer
Safety Wire
ENCODER ASSEMBLY Primary Restraint

wired (8 bolts) Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
ENCODER COVER Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
ENCODER GEAR Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.3. BONNET/MOTOR MOUNT ASSEMBLY
S-PIPE ADAPTOR Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire
BONNET ASSEMBLY Primary Restraint

wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015

Secondary Restraint
Wedge Lock Washer
Safety Wire

Wedge Lock Washer
Safety Wire

Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
1.4. ASSY, HYDRAULIC, GDM

STANDJUMP Primary Restraint
ACCUMULATOR Hex head Cap screw
Safety Wire
HYDRAULIC VALVE Primary Restraint

BANK ASSEMBLY Hex head Cap screw
. Wedge Lock Washer
Safety Wire
HYDRAULIC FILTER Primary Restraint

Secondary Restraint
. Wedge Lock Washer
Safety Wire
HYDRAULIC FILTER Primary Restraint

wired (4 bolts @ 2 Loctite
places) Secondary Restraint
Safety Wire
TITLE: Form:
349
DATE Nov 2015
This Page left blank intentionally
TITLE: Form:
349
DATE Nov 2015
1.5. LUBE SYSTEM, GDM

ASSY, LUBE PUMP Primary Restraint
wired (2 Bolts) Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire

MOTOR Hex head Cap screw
Wedge Lock Washer
Safety Wire

MOUNTING Hex head Cap screw
Bolts torqued and lock Flat washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
2. ASSY, MOTOR, GDM
DOMINATOR MOTOR Primary Restraint

LEAD J-BOX Hex head Cap screw
Bolts torqued and lock Flat Washer
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015

VENT COVER ( 2 or 3 Hex head Cap screw
vent covers based on Dry Moly Lube
motor) Secondary Restraint
Bolts torqued and lock Wedge Lock Washer
wired Safety Wire

VENT COVER (as Hex head Cap screw
above) Flat Washer
Split Lock Washer
Safety Wire

COVER Bolts torqued Hex head Cap screw
and lock wired (8 bolts) Flat Washer
on motor Loctite
Secondary Restraint
Split Lock Washer
Safety Wire

File Photo 2 FRONT SEAL COVER Hex head Cap screw
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015

BRAKE END SEAL Hex head Cap screw
COVER Dry Moly Lube
wired Wedge Lock Washer
Safety Wire

ENCODER MOUNT Hex head Cap screw
Bolts torqued and lock Flat washer
wired (1 bolt) Loctite
Secondary Restraint
Safety Wire

COVER Hex head Cap screw
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
GE MOTOR D.S. Primary Restraint

INSPECTION PLATE Hex head Cap screw
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
GE MOTOR INNER Primary Restraint

RETENTION BOLTS Hex head Cap screw
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
GE MOTOR LEAD J- Primary Restraint

BOX Hex head Cap screw
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
GE MOTOR COVER Primary Restraint

(752 /B20) Hex head Cap screw
wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire
MOTOR PLENUM Primary Restraint

wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
OIL FILL CAP Primary Restraint

wired Dry Moly Lube
Safety wire on cap Secondary Restraint
Wedge Lock Washer
Safety Wire
MOTOR PLENUM Primary Restraint

wired (8 bolts @ 2 Loctite
Safety Wire
MOTOR MOUNTING Primary Restraint

BOLTS ( 4 Bolts) SUPERBOLT
Bolts torqued and lock (Multi-Jack Bolt Tensioners (MJT))
wired (12 multi torque JL-G or JL-M lubricant
screw) on each Secondary Restraint
Safety Wire
MOTOR MOUNTING Primary Restraint

BOLTS ( 4 Bolts) Hex head Cap screw
Wedge Lock Washer
Safety Wire
File Photo 3
TITLE: Form:
349
DATE Nov 2015
2.1. BRAKE VALVE ASSEMBLY
INSPECTION PLATE Primary Restraint

wired (4 bolts) on Flat Washer
motor. 2 bolts on Secondary Restraint
switch All Metal Locking Nut
Safety Wire
TITLE: Form:
349
DATE Nov 2015
2.2. HYDRAULIC & LUBE MANIFOLD ASSEMBLY
HYDRAULIC & LUBE Primary Restraint

MANIFOLD ASSEMBLY Socket head Cap screw
wired (4 manifolds) To Secondary Restraint
mounting plate High Collar Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
2.3. ASSY, MOTOR, DISC BRAKE

BRAKE RING SPACER Socket head Cap screw
Wedge Lock Washer
Safety Wire
BRAKE CALIPER Primary Restraint

MOUNTS Hex head Cap screw
@ 2 spots. Bolts Dry Moly Lube
(2 bolts per caliper) Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
BRAKE CALIPER Primary Restraint

@ 2 spots Bolts Loctite
Safety Wire
BRAKE DISC Primary Restraint

torqued and lock wired Loctite
Secondary Restraint
Safety Wire
BRAKE DISC GUIDE Primary Restraint

BOLTS Hex head Cap screw
wired Loctite
Secondary Restraint
Safety Wire

BOLTS Socket head Cap screw
Safety Wire
TITLE: Form:
349
DATE Nov 2015

BOLTS Hex head Cap screw
wired (4 bolts) per Secondary Restraint
caliper. All Metal Locking Nut
BRAKE COVER Primary Restraint

Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
2.4. ASSY, BLOWER
BLOWER MOTOR J- Primary Restraint

BOX COVER Hex head Cap screw
Wedge Lock Washer
Safety Wire
BLOWER INLET Primary Restraint

File Photo 4 INSPECTION COVER Hex head Cap screw
Stainless Steel Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
BLOWER AIR INTAKE Primary Restraint

HOOD Hex head Cap screw
Stainless Steel Wedge Lock Washer
Safety Wire
BLOWER MOTOR Primary Restraint

MOUNTING BOLTS Hex head Cap screw
Wedge Lock Washer
Safety Wire
BLOWER MOTOR END Primary Restraint

CAP BOLTS Hex head Cap screw
Through bolts torqued Anti- seize
and lock wired Secondary Restraint
Split Lock Washer
Safety Wire
IMPELLOR HOUSING Primary Restraint

TO MOTOR INLET Hex head Cap screw
BOLTS Flat Washer
Through bolts torqued Secondary Restraint
and lock wired All Metal Locking Nut
Safety Wire
TITLE: Form:
349
DATE Nov 2015
MOTOR INLET TO Primary Restraint

MOTOR Hex head Cap screw
Through bolts torqued Flat Washer
and lock wired Loctite
Secondary Restraint
Split Lock Washer
Safety Wire

MOUNTING BOLTS (1 Hex head Cap screw
of 2) Flat Washer
Through bolts torqued Slotted Nut
Cotter Pin
Safety Wire

MOUNTING BOLTS Hex head Cap screw
(2 of 2) Flat Washer
Through bolts torqued Slotted Nut
Cotter Pin
Safety Wire
TITLE: Form:
349
DATE Nov 2015
3. GUARD ASSEMBLY
TITLE: Form:
349
DATE Nov 2015
GUARD LOGO MOUNT Primary Restraint

Through bolts torqued Hex head Cap screw
and lock wired Flat Washer
Secondary Restraint
Safety Wire
GUARD Primary Restraint

Pins secured and lock Pin
Cotter Pin
Safety Wire
GUARD UPPER Primary Restraint

MOUNT Hex head Cap screw
Cotter Pin
Safety Wire
GUARD MOUNT Primary Restraint

File Photo 5 Through bolts (4 bolts Socket head Cap screw
per side) torqued and Loctite
lock wired Secondary Restraint
Safety Wire
TITLE: Form:
349
DATE Nov 2015

Through bolts ( 5 bolts Socket head Cap screw
per side) torqued and Loctite
lock wired (2 places) Secondary Restraint
Safety Wire

(3 bolts per side) (1 OF Hex head Cap screw
3) Flat Washer
and lock wired (2 All Metal Locking Nut
places) Safety Wire

(as above) (2 OF 3) Hex head Cap screw
Safety Wire

Bolts (3) torqued and Flat Washer
lock wired (2 places) Secondary Restraint
Safety Wire
TITLE: Form:
349
DATE Nov 2015
GUARD HINGE ROD Primary Restraint

Through rods torqued Threaded rod
and cotter pinned (2 Flat Washer
places) Slotted Nut
Secondary Restraint
Cotter Pin
GUARD DOORS Primary Restraint

File Photo 6 Safety latches closed Pins
and lock wired (3 Secondary Restraint
places) Cotter Pin
Safety Wire
GUARD PLATFORM Primary Restraint

Safety latches closed Pin
places) Cotter Pin
Safety Wire
COOLER MOUNTS Primary Restraint

Safety latches closed Hex head Cap screw
and lock Flat Washer
Secondary Restraint
Safety Wire
TITLE: Form:
349
DATE Nov 2015
COOLER MOUNTS Primary Restraint

Safety latches closed Hex head Cap screw
and lock wired Flat Washer
Secondary Restraint
Safety Wire
GAUGE PANEL Primary Restraint

Through bolts (2 bolts Pan head Cap screw
per side) torqued and Secondary Restraint
lock wired Nylon Locking Nut
GAUGE PANEL Primary Restraint

Through bolts (3 bolts Pan head Cap screw
per gauge) torqued Secondary Restraint
and lock nutted Nylon Locking Nut
TITLE: Form:
349
DATE Nov 2015
4. BUW ASSY, GDM
PIVOT PIN ASSEMBLY Primary Restraint

Torque nut to spec. Pin
Insure tang on lock Anti-seize
washer is bent and Secondary Restraint
pushed squarely in to Tab lock washers
nut minimum 1 slot Lock Nut
GRABBER CYLINDER Primary Restraint

File Photo 7 RETAINERS Hex head Cap screw
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
SPRING POST Primary Restraint

wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
SPRING POST Primary Restraint

RETENTION Hex head Cap screw
Bolts (1) torqued and Secondary Restraint
lock nutted All metal lock nut
BELL GUIDE SAFETY Primary Restraint

SECURING Hex head Cap screw
3/16” stainless steel Dry Moly Lube
safety cable attached Secondary Restraint
to both guides and Wedge Lock Washer
secured to Grabber Safety Wire
Torque Box Side, Safety Securing
Grabber Assembly. Stainless steel wire rope
BELL GUIDE SAFETY Primary Restraint

SECURING Hex head Cap screw
3/16” stainless steel Dry Moly Lube
safety cable attached Secondary Restraint
to both guides and Wedge Lock Washer
secured to Grabber Safety Wire
Torque Box Side, Safety Securing
Grabber Assembly. Stainless steel wire rope
TITLE: Form:
349
DATE Nov 2015
4.1. GRABBER SPRING STABILIZER ASSEMBLY
GRIPPER SPRING Primary Restraint

SAFETY SECURING Socket head Cap screw
3/16” stainless steel Loctite
safety cable (as below) Secondary Restraint
Safety Wire
Safety Securing
TITLE: Form:
349
GDS DROPPED OBJECTS MANUAL REVISION 0
DATE Nov 2015
PAGE 77 of 104
GRIPPER SPRING Primary Restraint

STABILIZER Nuts @ 2
Torque Stover Locks Secondary Restraint
and safety wire Cotter Pin
Safety Wire
Contacts: Service Manager GDS International LLC 9841 Windmill Park Lane Houston, Texas 77064
Telephone: 713-623-1449 Website: www.globaldrillingsupport.com
TITLE: Form:
349
DATE Nov 2015
4.2. GRABBER BOX ASSEMBLY
TITLE: Form:
349
DATE Nov 2015
SIDE TORQUE BOX Primary Restraint

Through bolts torqued Socket head Cap screw
Secondary Restraint
Safety Wire
SIDE TORQUE BOX Primary Restraint

Secondary Restraint
Safety Wire
Safety Securing
DIE BLOCKS Primary Restraint

Through bolts (4 per Hex head Cap screw
block) @ 2 places Dry Moly Lube
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
5. BLOCK INTERFACE ASSEMBLY, WITH SIDE PLATES
BAIL PINS Primary Restraint

(1 of 2) Hex head Cap screw
Bolts torqued (2 bolts Dry Moly Lube
@ 2 places) Secondary Restraint
Wedge Lock Washer
Safety Wire

Retaining Ring
(2 of 2) Pin
2 pins @ 2 places Anti-seize
Secondary Restraint
Retaining Plate
TITLE: Form:
349
DATE Nov 2015
COUNTERBALANCE Primary Restraint

CYLINDER PINS Pin
Bolts and Locknuts Hex head Cap screw
torqued (1 bolt @ 2 All Metal Locking Nut
places).2 cylinders per Safety Wire
top drive
COUNTERBALANCE Primary Restraint

CYLINDER PINS Pin
Bolts torqued (1 bolt Secondary Restraint
@ 2 places).2 Hex head Cap screw
cylinders per top All Metal Locking Nut
drive Safety Wire
TITLE: Form:
349
DATE Nov 2015
5.1. BLOCK INTERFACE ASSY
RETAINER, SIDE Primary Restraint

BLOCK, INTERFACE Hex head Cap screw
ASSEMBLY Dry Moly Lube
Bolts torqued (4 bolts Secondary Restraint
@ 2 places) Wedge Lock Washer
Safety Wire

Bolts and Stover Pin
locknuts torqued (2 Secondary Restraint
bolts @ 2 places). Hex head Cap screw
Note: Bale not shown All Metal Locking Nut
for clarity
TITLE: Form:
349
DATE Nov 2015
6. SERVICE LOOP MOUNT ASSEMBLY, TD SIDE, GDM
SERVICE LOOP MOUNT Primary Restraint

wired on Service Loop Loctite
Plate Secondary Restraint
Safety Wire
Safety Securing
SERVICE LOOP MOUNT Primary Restraint

PLUGS AND CAPS Coupler Cap
Safety Wiring installed Secondary Restraint
to retain caps Safety Wire
TITLE: Form:
349
DATE Nov 2015
SERVICE LOOP PLUGS Primary Restraint

Through bolts (4 bolt Pan head Cap screw
and locknuts @ 3 Secondary Restraint
plugs) torqued Nylon Lock Nut
Safety Wire
SERVICE LOOP PLUGS Primary Restraint

Through bolts (4 bolt Pan head Cap screw
and locknuts @ 3 Secondary Restraint
plugs) torqued Nylon Lock Nut
Safety Wire
File Photo 8
TITLE: Form:
349
DATE Nov 2015
7. ASSY, GOOSENECK
Mudline Primary Restraint

and lock wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
Mudline Primary Restraint

and lock wired Dry Moly Lube
Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
Mudline Blanking Cap Primary Restraint

Safety Wiring installed Blanking Cap
to retain caps Anti-seize
Secure with Safety Safety Securing
Cable Clevis
Cotter pin
TITLE: Form:
349
DATE Nov 2015
8. ASSY, SLIDER FRAME, OFFSET
Slider Adjuster Bolts Primary Restraint

Through bolts (4 bolts Socket head Cap screw
@ 4 places) torqued Dry Moly
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
SLIDER FRAME Primary Restraint

ADJUSTER CAPS Socket head Cap screw
Through bolts (4 bolts Dry Moly
@ 2 places @ 2 sides) Secondary Restraint
torqued and lock Wedge Lock Washer
wired Safety Wire
Safety Wiring installed
to retain caps
SLIDER SECONDARY Primary Restraint

SECURING Eye Bolt
Secure slider (2 per Quick Link
side @ 2 sides)with Safety Securing
Safety Cable Stainless steel wire rope

ADJUSTER BOLTS Hex head Cap screw
Through bolts (bolts @ Dry Moly
2 places) torqued and Secondary Restraint
lock wired Wedge Lock Washer
Safety Wire
Slider Frame Adjuster Primary Restraint

Bolts Hex head Cap screw
Safety Wire
TITLE: Form:
349
DATE Nov 2015
Slider Frame Adjuster Primary Restraint

Bolts Hex head Cap screw
Safety Wire
Contacts: Service Manager Premium LLC 9841 Windmill Park Lane Houston, Texas 77064
Telephone: 713-623-1449 Website: www.globaldrillingsupport.com
TITLE: Form:
349
DATE Nov 2015
9. LOWER WELL CONTROL VALVE AND ACTUATOR

LOWER WELL CONTOL Primary Restraint
VALVE ANTI- Hex head Cap screw
ROTATION MOUNT Dry Moly
Mount secure to Secondary Restraint
actuator, properly Wedge Lock Washer
adjusted and secure Safety Wire
Secondary Safety
Stainless Steel Cable
Eye Bolt
Quick Link
TITLE: Form:
349
DATE Nov 2015
10.SERVICE LOOPS
SERVICE LOOP Primary Restraint

SADDLE Pin
Pins and Shackles 3 Anti-seize
(places) Secondary Restraint
Cotter pin
SERVICE LOOP Primary Restraint

SADDLE Pin
Pins and Shackles 3 Anti-seize
(places) Secondary Restraint
Cotter pin
TITLE: Form:
349
DATE Nov 2015
11. TRAVELING BLOCK /BLOCK INTERFACE
TRAVELING BLOCK Primary Restraint

SIDE COVER Hex head Cap screw
(2 COVERS @ 18 Secondary Restraint
BOLTS) All Metal Lock Nut
Through bolts torqued Safety Wire
and lock wired
TRAVELING BLOCK Primary Restraint

LOGO PLATE Hex head Cap screw
and lock wired Wedge Lock washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
STOP PIN CAP Primary Restraint

Through bolts (8 bolts Hex head Cap screw
Wedge Lock Washer
Safety Wire
MAIN SHAFT Primary Restraint

Through bolts (8 bolts Hex head Cap screw
Wedge Lock Washer
Safety Wire
SECONDARY SAFETY Secondary Safety

Stainless Steel Wire Rope
Clevis with pin and slotted nut
MIDDLE COVER Primary Restraint

Through bolts (8 bolts Hex head cap screw
Wedge Lock Washer
TITLE: Form:
349
DATE Nov 2015
BAIL PIN Primary Restraint

Pins installed, bolts Pin
and lock nuts torqued Anti-seize
Secondary Restraint
Bolt
All metal lock bolt
COVER LOCK Primary Restraint

File Photo 9 Through bolts torqued Hex head Cap screw
and lock wired Dry Moly
Secondary Restraint
Wedge Lock Washer
Safety Wire
COVER LATCH Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire

Through bolts torqued Dry Moly
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
SLIDER FRAME BOLTS Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire
SLIDER SECONDARY Primary Restraint

RETENTION Eye Bolt
Eye bolts torqued and Loctite
safety cabled Safety Secondary
Safety Cable
Contacts: Service Manager Prmium International LLC 9841 Windmill Park Lane Houston, Texas
TITLE: Form:
349
DATE Nov 2015
12. TORQUE REACTION ASSEMBLIES

TORQUE REACTION Primary Restraint
BEAM Pin
Pins installed, bolts Anti-seize
and lock nuts torqued Secondary Restraint
Bolt
All metal lock bolt
MID MAST MOUNTS Primary Restraint

Pins installed, bolts Pin
and lock nuts torqued Anti-seize
Secondary Restraint
Bolt (no anti-seize)
All metal lock bolt
SLIDE PLATE BOLTS Primary Restraint

Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
TORQUE REACTION Primary Restraint

THREADED ROD Threaded rod
Anco Lock Nut
TITLE: Form:
349
DATE Nov 2015
13. TRACK ASSEMBLY
TRACK CONNECTION Primary Restraint

Pins fully installed, Pin
bolts and nuts torqued Anti-seize
Secondary Restraint
All metal lock bolt
TRACK CONNECTION Primary Restraint

Pins fully installed, Pin
bolts and nuts torqued Anti-seize
Secondary Restraint
All metal lock bolt
TITLE: Form:
349
DATE Nov 2015
14. CROWN INTERFACE

CROWN INTERFACE Primary Restraint
BAR Clevis with Pin
Pins fully installed in Slotted Nut
clevises. Slotted nut Secondary Restraint
tight, cotter pin Cotter Pin
installed and bent. Safety Secondary
Safety Cable
Clevis with Pin
TITLE: Form:
349
DATE Nov 2015
15. EXTEND/RETRACT FRAMES
ARM, EXTEND FRAME, Primary Restraint

UPPER Socket head Cap screw
Through bolts torqued Retention Plate
and lock wired (4 Dry Moly
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
PAD - BELTED RUBBER Primary Restraint

places) All metal lock nut
Safety Wire
ARM, MINOR, EXTEND Primary Restraint

FRAME Hex head Cap screw
and lock wired (4 All metal lock nut
places) Safety Wire
SLIDER ADJUSTER Primary Restraint

and lock wired (8 All metal lock nut
places) Safety Wire
SLIDER ADJUSTER Primary Restraint

ASSEMBLY Eye Bolt
Eye bolts torqued (4 Flat Washer
place) Secondary Restraint
All metal lock nut
Safety Secondary
Stainless Steel Wire Rope
Quick Link
TITLE: Form:
349
DATE Nov 2015
HYDRAULIC CYLINDER Primary Restraint

END RETENTION Socket head Cap screw
(2 Places) Secondary Restraint
Wedge Lock Washer
Safety Wire
HYDRAULIC CYLINDER Primary Restraint

ROD END RETENTION Socket head Cap screw
(2 Places) Secondary Restraint
Wedge Lock Washer
Safety Wire
CARRIAGE GUIDE Primary Restraint

(2 places) Flat Washer
Loctite
Secondary Restraint
Wedge Lock Washer
Safety Wire
TITLE: Form:
349
DATE Nov 2015
Section 5 - Ordering Replacement Parts
Occasionally, there is a need to obtain new parts for your GDM. It is important to replace
failed or damaged components with Premium certified parts to insure they are “form, fit,
and function.” Use of incorrect parts could result in equipment damage or injury to
personnel. When ordering parts, it is helpful to provide the following information:
 Equipment serial number

 Component part number and description
 Applicable assembly number
 Quantity required
 Required delivery of the parts
TITLE: Form:
349
DATE Nov 2015
Section 6 – Revision Notice

The methods, procedures, and guidelines described in this manual reflect
Premium’s current manufacturing processes as of the date of the publication of this
manual. Premium anticipates further revisions to this manual, and you should
contact the Service Manager to insure you have the latest version of the manual.
GDM 850 - DRILLMEC
5
Section
Certifications
Contents
Certificate of Compliance 5-3
Certificate of Registration 5-4
API Accreditations 5-5
Certificate of Origin 5-6
5-1
CERTIFICATE OF COMPLIANCE
5-2
CERTIFICATE OF COMPLIANCE
Customer: DRILLMEC INC MEXICO
Customer P.O.: POC2000199
Description / Serial Number: GDM TOP DRIVE & EXTEND FRAME/ SERIAL # 54
Quantity: 1
GDS Work Order Number: R13970
The undersigned hereby certifies that the equipment referenced above conforms to the customer’s
purchase order requirements, API Spec 8C (as applicable), and generally accepted industry practices.
Deviations and exceptions are as follows:
None
All documentation related to this order is available for examination upon request.
r}
Director of Quality/HSE
GDS INTERNATIONAL,
LLC:8/2/2022
22/58
Form 128 Rev 1 October 2014
GDS INTERNATIONAL, LLC
9841 Windmill Park Lane
Houston, TX
Design, Manufacture, Service, and Supply of Drilling and Hoisting Equipment for
the Petroleum and Natural Gas Industries
No Exclusions Identified as Applicable
Effective Date: SEPTEMBER 20, 2019

Expiration Date: OCTOBER 4, 2022
Registered Since: OCTOBER 4, 2013
Vice President of Global Industry Services
19/58
8C-0161
GDS INTERNATIONAL, LLC

9841 Windmill Park Lane
Houston, TX
API-8C
8C-0161
The scope of this license includes the following: Block-to-Hook Adapters, Power Swivels, Traveling Blocks
and/or Hook Blocks, Guide Dollies for Travelling Equipment at PSL 1, PSL 2
QMS Exclusions: No Exclusions Identified as Applicable
Effective Date: OCTOBER 4, 2019

Expiration Date: OCTOBER 4, 2022
Vice President of Global Industry Services

CERTIFICATE OF ORIGIN
We, Premium Oilfield Drilling Equipment and Support, certify

the following product/products shipped on order R13970 is/are the products assembled and
tested in the United States of America and shipped from Houston, Texas.
Description GDM TOP DRIVE & EXTEND FRAME
Serial Number 54
Part Number A801000
Customer Name DRILLMEC INC. MEXICO
Customer P.O. Number POC2000199

Job Number R13970
08/17/2022
r}
___________________________ ________________________
QUALITY CONTROL DATE
Form 377 Rev 0 August 2022

GDM 850 Drillmec Manual Spanish

Cargado por

Copyright:

Formatos disponibles

GDM 850 Drillmec Manual Spanish

Cargado por

Información del documento

Título original

Derechos de autor

Formatos disponibles

Compartir este documento

Compartir o incrustar documentos

Opciones para compartir

¿Le pareció útil este documento?

¿Este contenido es inapropiado?

Copyright:

Formatos disponibles

GDM 850 Drillmec Manual Spanish

Cargado por

Copyright:

Formatos disponibles

850 TON TOP DRIVE

Seccion 1 – General ............................................................................................. 1-1

Seccion 2 – Mantenimiento e Inspección .......................................................... 2-1

Seccion 3 – Diagramas y Partes ......................................................................... 3-1

• Manual de Prevención de Caídas de Objetos

Seccion 5 – Certificaciones .................................................................................5-1

Uso del Manual

Contiene un resumen de este manual y define los términos de precaución;

3 – Diagramas y Contiene Diagramas de Ensamblaje, Diagramas Eléctricos, Diagramas

4 – Prevención de Contiene estándares y prácticas para retención secundaria

5 – Certificaciones Certificados de Conformidad y Premium’s API Certificaciones y Licencias

Importante Información de Seguridad

ADVERTENCIA (WARNING)– Este término precede inmediatamente o sigue

PRECAUCION (CAUTION) – Este término se refiere a cualquier técnica o procedimiento

NOTA (NOTE) – Este término se usa para enfatizar información importante.

Especificaciones del Top Drive

Carga de Peso Estatico 850 Toneladas Cortas

Datos del Torque

GDM-850 TON TOP DRIVE PERFORMANCE CURVE -- 1,200 HP

GDM 850- DRILLMEC Rev. 1 2-1

Listado de Mantenimiento 2-55

GDM 850- DRILLMEC Rev. 1 2-2

Punto de Engrase Pastillas del freno,

Inspeccionar el respiradero Punto de Engrase

Punto de Engrase Punto de Engrase

Punto de Engrase Punto de Engrase

DRILLMAX 175T MOTOR

DOCUMENT NUMBER REV

SUBJECT TO CHANGE WITHOUT NOTICE 1 of 33

DRILLMAX 175T MOTOR

Gulf Electroquip Ltd.

© Copyright 2022 Gulf Electroquip

01 07/25/2022 General Refinements K.V. S.V

00 05/31/2022 Initial Release S. V. K.V

SUBJECT TO CHANGE WITHOUT NOTICE 2 of 33

DRILLMAX 175T MOTOR

1 INTRODUCTION AND DESCRIPTION......................................................................................... 5

DRILLMAX 175T MOTOR

4.8 Troubleshooting .............................................................................................................. 25

SUBJECT TO CHANGE WITHOUT NOTICE 4 of 33

DRILLMAX 175T MOTOR

INTRODUCTION AND DESCRIPTION

1.2 Safety Overview

A Caution statement indicates a condition that can cause damage to equipment.

High Voltage warning – Connections that might be energized.

SUBJECT TO CHANGE WITHOUT NOTICE 5 of 33

DRILLMAX 175T MOTOR

SUBJECT TO CHANGE WITHOUT NOTICE 6 of 33

DRILLMAX 175T MOTOR

SUBJECT TO CHANGE WITHOUT NOTICE 7 of 33

DRILLMAX 175T MOTOR

1.3 List of Terms and Symbols

GEQ: Refers to the company name Gulf Electroquip Ltd.

SUBJECT TO CHANGE WITHOUT NOTICE 8 of 33

DRILLMAX 175T MOTOR

1.4 Motor Data & Description

Rated Output 1200 HP

Rated Voltage 575 V

Rated Frequency 40.6 Hz