stc8prog is a command line flash programming tool for STC 8051 series microcontrollers, Currently, only STC8H/STC8G/STC8A, STC15 (FWVER > 0x72) series are supported.

STC microcontrollers have an UART/USB based boot strap loader (BSL). It utilizes a packet-based protocol to flash the code memory and IAP memory over a serial link. This is referred to as in-system programming (ISP). This tool is built according to the ISP described in STC8H datasheet.

• STC8A8K64S4A12
• STC8A8K64D4
• STC8G1K08A
• STC8H1K08
• STC8H3K32S2
• STC8H3K64S4
• STC8H8K64U
• STC15W104
• STC15F104W
• STC15W408AS
• STC15F2K60S2

Usage: stc8prog [options]...
  -h, --help                    display this message
  -p, --port <device>           set device path
  -s, --speed <baud>            set download baudrate
  -r, --reset <msec>            make reset sequence by pulling low dtr
  -r, --reset <cmd> [args] ;    command to perform reset or power cycle
  -f, --flash <file>            flash chip with data from hex file
  -e, --erase                   erase the entire chip
  -d, --debug                   enable debug output
  -v, --version                 display version information

Baudrate options: 
   4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 500000, 576000,
   921600, 1000000, 1152000, 1500000, 2000000, 2500000, 3000000, 3500000,
   4000000

Communicate with MCU without changing anything. It will communicate in 2400 baud first, then switch to a higher baud for a second check

# 2400 baud -> 115200 baud
./stc8prog -p /dev/ttyUSB0

You can specify other baud with parameter -s

# 2400 baud -> 1152000 baud
./stc8prog -p /dev/ttyUSB0 -s 1152000

This will erase the flash.

./stc8prog -p /dev/ttyUSB0 -e

Suggest to erase before writing flash

./stc8prog -p /dev/ttyUSB0 -e -f foo.hex

High baudrate will speed up the writing

./stc8prog -p /dev/ttyUSB0 -s 1152000 -e -f foo.hex

By default PlatformIO places packages at /home/[username]/.platformio/packages

1. create a folder named tool-stc8prog under it
2. and place stc8prog executable under it.

Create a new env in platformio.ini, it can be a clone of existing one, change the name and change upload_protocol option to custom, then configurate the rest accordingly, for example:

[env:stc8h3k32s2-stc8prog]
platform = intel_mcs51
board = stc8h3k32s2
upload_protocol = custom
upload_port = /dev/ttyUSB0
upload_flags =
    -p
    $UPLOAD_PORT
    -s
    1152000
    -e
upload_command = ${platformio.packages_dir}/tool-stc8prog/stc8prog $UPLOAD_FLAGS -f $SOURCE

If you want to reset the MCU by pulling DTR line low, add -r 5 to upload_flags config
If you want to make this env default, set it to default_envs

[platformio]
default_envs = stc8h3k32s2-stc8prog

For more options, please read platformio section_env_upload

You can trigger upload with hotkey Ctrl+Alt+U.

If there are any erros and you want to see more detailed logs, run it in the verbose way:

1. Click PlatformIO icon in the left navigation panel
2. Expand [your env name] in PROJECT TASKS
3. Expand Advanced
4. Click Verbose Upload, this will output the full log of all commands

• Linux

sudo apt install build-essential

• macOS

xcode-select --install

git clone https://github.com/IOsetting/stc8prog.git

cd stc8prog
make

sudo make install

Package dev-embedded/stc8prog-9999 located in unoficial rasdark overlay. Resulting binary will be from last commit from https://github.com/IOsetting/stc8prog.git

1. Run Cygwin setup
2. Install 'gcc-core' and 'make' packages
3. Use command-line git to pull latest stc8prog source to desired folder
4. Run Cygwin terminal
5. Navigate to folder with stc8prog source (windows disks are mapped to /cygdrive; eg. to navigate to 'stc8prog' folder located on 'D' drive, use 'cd /cygdrive/d/stc8prog/')
6. Run make to build binary

• By default, Cygwin's gcc binary requires cygwin1.dll to work correctly, just copy it from Cygwin installation dir bin folder