The split-ring test provides a simple benchmark for correlating springback obtained by finite ele... more The split-ring test provides a simple benchmark for correlating springback obtained by finite element analysis (FEA) with experimental measurements. This test consists in cutting a ring specimen from a full drawn cup and then to split the ring longitudinally along a radial plane. The difference between the ring diameters, before and after splitting, gives a direct measure of the springback
ABSTRACT Deep drawing is one of the most important operations used in sheet metal forming. Within... more ABSTRACT Deep drawing is one of the most important operations used in sheet metal forming. Within this, forming of cylindrical cup is one of the most widely studied deep drawing processes since it allows analysing the effect of different process parameters in phenomena such as earing, springback and ironing. In fact, during the deep drawing of a cylindrical cup the blank thickness gradually increases as the blank outer diameter is reduced to the die inner diameter, resulting in a thickness increase from a point near the bottom radius until the maximum value at the top of the cup. Therefore, if the gap between the punch and the die is not sufficiently large to allow the blank material to flow, ironing of the cup wall will occur. The ironing process typically imposes high contact forces, normal to the surface of the punch and the die, which can lead to the occurrence of galling, particularly for aluminium alloys. In this work an experimental device, adopted in previous studies, was used to analyse the influence of the lubricant conditions in the deep drawing of a cylindrical cup. The study considers an AA5754-O aluminium alloy blank with a diameter of 60 mm, which is fully deep drawn with a 33 mm diameter punch. Due to the forming conditions, the cup is deep drawn and ironing of the cup wall also occurs. The experimental tests were performed considering different amounts of lubricant in the blank surfaces in the contact with the die and with the blank-holder in order to better understand the influence of these tools on the process. The experimental study was complemented with numerical simulations, exploring the conditions induced by the ironing operation, quite challenging for the numerical simulation of the process using the finite element method. Besides the influence of the contact with friction conditions in the forming process (i.e. punch force evolution, thickness distribution along the cup wall and contact pressure), the influence of the die shoulder and inner radius were also analysed.
The split-ring test provides a simple benchmark for correlating springback obtained by finite ele... more The split-ring test provides a simple benchmark for correlating springback obtained by finite element analysis (FEA) with experimental measurements. This test consists in cutting a ring specimen from a full drawn cup and then to split the ring longitudinally along a radial plane. The difference between the ring diameters, before and after splitting, gives a direct measure of the springback
ABSTRACT Deep drawing is one of the most important operations used in sheet metal forming. Within... more ABSTRACT Deep drawing is one of the most important operations used in sheet metal forming. Within this, forming of cylindrical cup is one of the most widely studied deep drawing processes since it allows analysing the effect of different process parameters in phenomena such as earing, springback and ironing. In fact, during the deep drawing of a cylindrical cup the blank thickness gradually increases as the blank outer diameter is reduced to the die inner diameter, resulting in a thickness increase from a point near the bottom radius until the maximum value at the top of the cup. Therefore, if the gap between the punch and the die is not sufficiently large to allow the blank material to flow, ironing of the cup wall will occur. The ironing process typically imposes high contact forces, normal to the surface of the punch and the die, which can lead to the occurrence of galling, particularly for aluminium alloys. In this work an experimental device, adopted in previous studies, was used to analyse the influence of the lubricant conditions in the deep drawing of a cylindrical cup. The study considers an AA5754-O aluminium alloy blank with a diameter of 60 mm, which is fully deep drawn with a 33 mm diameter punch. Due to the forming conditions, the cup is deep drawn and ironing of the cup wall also occurs. The experimental tests were performed considering different amounts of lubricant in the blank surfaces in the contact with the die and with the blank-holder in order to better understand the influence of these tools on the process. The experimental study was complemented with numerical simulations, exploring the conditions induced by the ironing operation, quite challenging for the numerical simulation of the process using the finite element method. Besides the influence of the contact with friction conditions in the forming process (i.e. punch force evolution, thickness distribution along the cup wall and contact pressure), the influence of the die shoulder and inner radius were also analysed.
Uploads