chapter1.fm Page 9 Friday, January 18, 2002 8:58 AM
CHAPTER
1
INTRODUCTION
The evolution of digital circuit design
n
Compelling issues in digital circuit design
n
How to measure the quality of a design
n
Valuable references
1.1
A Historical Perspective
1.2
Issues in Digital Integrated Circuit Design
1.3
Quality Metrics of a Digital Design
1.4
Summary
1.5
To Probe Further
9
chapter1.fm Page 10 Friday, January 18, 2002 8:58 AM
INTRODUCTION
10
1.1
Chapter 1
A Historical Perspective
The concept of digital data manipulation has made a dramatic impact on our society. One
has long grown accustomed to the idea of digital computers. Evolving steadily from mainframe and minicomputers, personal and laptop computers have proliferated into daily life.
More significant, however, is a continuous trend towards digital solutions in all other
areas of electronics. Instrumentation was one of the first noncomputing domains where the
potential benefits of digital data manipulation over analog processing were recognized.
Other areas such as control were soon to follow. Only recently have we witnessed the conversion of telecommunications and consumer electronics towards the digital format.
Increasingly, telephone data is transmitted and processed digitally over both wired and
wireless networks. The compact disk has revolutionized the audio world, and digital video
is following in its footsteps.
The idea of implementing computational engines using an encoded data format is by
no means an idea of our times. In the early nineteenth century, Babbage envisioned largescale mechanical computing devices, called Difference Engines [Swade93]. Although
these engines use the decimal number system rather than the binary representation now
common in modern electronics, the underlying concepts are very similar. The Analytical
Engine, developed in 1834, was perceived as a general-purpose computing machine, with
features strikingly close to modern computers. Besides executing the basic repertoire of
operations (addition, subtraction, multiplication, and division) in arbitrary sequences, the
machine operated in a two-cycle sequence, called “store” and “mill” (execute), similar to
current computers. It even used pipelining to speed up the execution of the addition operation! Unfortunately, the complexity and the cost of the designs made the concept impractical. For instance, the design of Difference Engine I (part of which is shown in Figure 1.1)
required 25,000 mechanical parts at a total cost of £17,470 (in 1834!).
Figure 1.1 Working part of Babbage’s
Difference Engine I (1832), the first known
automatic calculator (from [Swade93],
courtesy of the Science Museum of
London).
chapter1.fm Page 11 Friday, January 18, 2002 8:58 AM
Section 1.1
A Historical Perspective
11
The electrical solution turned out to be more cost effective. Early digital electronics
systems were based on magnetically controlled switches (or relays). They were mainly
used in the implementation of very simple logic networks. Examples of such are train
safety systems, where they are still being used at present. The age of digital electronic
computing only started in full with the introduction of the vacuum tube. While originally
used almost exclusively for analog processing, it was realized early on that the vacuum
tube was useful for digital computations as well. Soon complete computers were realized.
The era of the vacuum tube based computer culminated in the design of machines such as
the ENIAC (intended for computing artillery firing tables) and the UNIVAC I (the first
successful commercial computer). To get an idea about integration density, the ENIAC
was 80 feet long, 8.5 feet high and several feet wide and incorporated 18,000 vacuum
tubes. It became rapidly clear, however, that this design technology had reached its limits.
Reliability problems and excessive power consumption made the implementation of larger
engines economically and practically infeasible.
All changed with the invention of the transistor at Bell Telephone Laboratories in
1947 [Bardeen48], followed by the introduction of the bipolar transistor by Schockley in
1949 [Schockley49]1. It took till 1956 before this led to the first bipolar digital logic gate,
introduced by Harris [Harris56], and even more time before this translated into a set of
integrated-circuit commercial logic gates, called the Fairchild Micrologic family
[Norman60]. The first truly successful IC logic family, TTL (Transistor-Transistor Logic)
was pioneered in 1962 [Beeson62]. Other logic families were devised with higher performance in mind. Examples of these are the current switching circuits that produced the first
subnanosecond digital gates and culminated in the ECL (Emitter-Coupled Logic) family
[Masaki74]. TTL had the advantage, however, of offering a higher integration density and
was the basis of the first integrated circuit revolution. In fact, the manufacturing of TTL
components is what spear-headed the first large semiconductor companies such as Fairchild, National, and Texas Instruments. The family was so successful that it composed the
largest fraction of the digital semiconductor market until the 1980s.
Ultimately, bipolar digital logic lost the battle for hegemony in the digital design
world for exactly the reasons that haunted the vacuum tube approach: the large power consumption per gate puts an upper limit on the number of gates that can be reliably integrated
on a single die, package, housing, or box. Although attempts were made to develop high
integration density, low-power bipolar families (such as I2L—Integrated Injection Logic
[Hart72]), the torch was gradually passed to the MOS digital integrated circuit approach.
The basic principle behind the MOSFET transistor (originally called IGFET) was
proposed in a patent by J. Lilienfeld (Canada) as early as 1925, and, independently, by O.
Heil in England in 1935. Insufficient knowledge of the materials and gate stability problems, however, delayed the practical usability of the device for a long time. Once these
were solved, MOS digital integrated circuits started to take off in full in the early 1970s.
Remarkably, the first MOS logic gates introduced were of the CMOS variety
[Wanlass63], and this trend continued till the late 1960s. The complexity of the manufacturing process delayed the full exploitation of these devices for two more decades. Instead,
1
An intriguing overview of the evolution of digital integrated circuits can be found in [Murphy93].
(Most of the data in this overview has been extracted from this reference). It is accompanied by some of the historically ground-breaking publications in the domain of digital IC’s.
chapter1.fm Page 12 Friday, January 18, 2002 8:58 AM
INTRODUCTION
12
Chapter 1
the first practical MOS integrated circuits were implemented in PMOS-only logic and
were used in applications such as calculators. The second age of the digital integrated circuit revolution was inaugurated with the introduction of the first microprocessors by Intel
in 1972 (the 4004) [Faggin72] and 1974 (the 8080) [Shima74]. These processors were
implemented in NMOS-only logic, which has the advantage of higher speed over the
PMOS logic. Simultaneously, MOS technology enabled the realization of the first highdensity semiconductor memories. For instance, the first 4Kbit MOS memory was introduced in 1970 [Hoff70].
These events were at the start of a truly astounding evolution towards ever higher
integration densities and speed performances, a revolution that is still in full swing right
now. The road to the current levels of integration has not been without hindrances, however. In the late 1970s, NMOS-only logic started to suffer from the same plague that made
high-density bipolar logic unattractive or infeasible: power consumption. This realization,
combined with progress in manufacturing technology, finally tilted the balance towards
the CMOS technology, and this is where we still are today. Interestingly enough, power
consumption concerns are rapidly becoming dominant in CMOS design as well, and this
time there does not seem to be a new technology around the corner to alleviate the
problem.
Although the large majority of the current integrated circuits are implemented in the
MOS technology, other technologies come into play when very high performance is at
stake. An example of this is the BiCMOS technology that combines bipolar and MOS
devices on the same die. BiCMOS is used in high-speed memories and gate arrays. When
even higher performance is necessary, other technologies emerge besides the already mentioned bipolar silicon ECL family—Gallium-Arsenide, Silicon-Germanium and even
superconducting technologies. These technologies only play a very small role in the overall digital integrated circuit design scene. With the ever increasing performance of CMOS,
this role is bound to be further reduced with time. Hence the focus of this textbook on
CMOS only.
1.2
Issues in Digital Integrated Circuit Design
Integration density and performance of integrated circuits have gone through an astounding revolution in the last couple of decades. In the 1960s, Gordon Moore, then with Fairchild Corporation and later cofounder of Intel, predicted that the number of transistors that
can be integrated on a single die would grow exponentially with time. This prediction,
later called Moore’s law, has proven to be amazingly visionary [Moore65]. Its validity is
best illustrated with the aid of a set of graphs. Figure 1.2 plots the integration density of
both logic IC’s and memory as a function of time. As can be observed, integration complexity doubles approximately every 1 to 2 years. As a result, memory density has
increased by more than a thousandfold since 1970.
An intriguing case study is offered by the microprocessor. From its inception in the
early seventies, the microprocessor has grown in performance and complexity at a steady
and predictable pace. The transistor counts for a number of landmark designs are collected
in Figure 1.3. The million-transistor/chip barrier was crossed in the late eighties. Clock
frequencies double every three years and have reached into the GHz range. This is illus-
chapter1.fm Page 13 Friday, January 18, 2002 8:58 AM
Section 1.2
Issues in Digital Integrated Circuit Design
13
64 Gbits
*0.08µm
1010
Human memory
Human memory
Human DNA
Human DNA
109
4 Gbits
1 Gbits
Number of bits per chip
108
256 Mbits
107
64 Mbits
106
Book
Book
16 Mbits
4 Mbits
105
1 Mbits
104
256 Kbits
0.15µm
0.15-0.2µm
0.25-0.3µm
0.35-0.4µm
0.5-0.6µm
0.7-0.8µm
1.0-1.2µm
1.6-2.4µm
64 Kbits
Encyclopedia
Encyclopedia
2 hrs CD Audio
2 hrs CD Audio
30
30sec
secHDTV
HDTV
Page
Page
1970
1980
1990
2000
2010
Year
(b) Trends in memory complexity
(a) Trends in logic IC complexity
Figure 1.2
Evolution of integration complexity of logic ICs and memories as a function of time.
trated in Figure 1.4, which plots the microprocessor trends in terms of performance at the
beginning of the 21st century. An important observation is that, as of now, these trends
have not shown any signs of a slow-down.
It should be no surprise to the reader that this revolution has had a profound impact
on how digital circuits are designed. Early designs were truly hand-crafted. Every transistor was laid out and optimized individually and carefully fitted into its environment. This
is adequately illustrated in Figure 1.5a, which shows the design of the Intel 4004 microprocessor. This approach is, obviously, not appropriate when more than a million devices
have to be created and assembled. With the rapid evolution of the design technology,
time-to-market is one of the crucial factors in the ultimate success of a component.
100000000
Pentium 4
Pentium III
Pentium II
Transistors
10000000
Pentium ®
1000000
486
386
100000
286 ™
8086
10000
4004
1000
1970
8080
8008
1975
1980
1985
1990
1995
2000
Year of Introduction
Figure 1.3
Historical evolution of microprocessor transistor count (from [Intel01]).
chapter1.fm Page 14 Friday, January 18, 2002 8:58 AM
INTRODUCTION
14
Chapter 1
10000
Doubles every
2 years
Frequency (Mhz)
1000
P6
100
Pentium ® proc
486
10
8086
8085
1
0.1
1970
286
386
8080
8008
4004
1980
1990
Year
2000
2010
Figure 1.4 Microprocessor performance
trends at the beginning of the 21st century.
Designers have, therefore, increasingly adhered to rigid design methodologies and strategies that are more amenable to design automation. The impact of this approach is apparent
from the layout of one of the later Intel microprocessors, the Pentium® 4, shown in Figure
1.5b. Instead of the individualized approach of the earlier designs, a circuit is constructed
in a hierarchical way: a processor is a collection of modules, each of which consists of a
number of cells on its own. Cells are reused as much as possible to reduce the design effort
and to enhance the chances for a first-time-right implementation. The fact that this hierarchical approach is at all possible is the key ingredient for the success of digital circuit
design and also explains why, for instance, very large scale analog design has never
caught on.
The obvious next question is why such an approach is feasible in the digital world
and not (or to a lesser degree) in analog designs. The crucial concept here, and the most
important one in dealing with the complexity issue, is abstraction. At each design level,
the internal details of a complex module can be abstracted away and replaced by a black
box view or model. This model contains virtually all the information needed to deal with
the block at the next level of hierarchy. For instance, once a designer has implemented a
multiplier module, its performance can be defined very accurately and can be captured in a
model. The performance of this multiplier is in general only marginally influenced by the
way it is utilized in a larger system. For all purposes, it can hence be considered a black
box with known characteristics. As there exists no compelling need for the system
designer to look inside this box, design complexity is substantially reduced. The impact of
this divide and conquer approach is dramatic. Instead of having to deal with a myriad of
elements, the designer has to consider only a handful of components, each of which are
characterized in performance and cost by a small number of parameters.
This is analogous to a software designer using a library of software routines such as
input/output drivers. Someone writing a large program does not bother to look inside those
library routines. The only thing he cares about is the intended result of calling one of those
modules. Imagine what writing software programs would be like if one had to fetch every
bit individually from the disk and ensure its correctness instead of relying on handy “file
open” and “get string” operators.
chapter1.fm Page 15 Friday, January 18, 2002 8:58 AM
Section 1.2
Issues in Digital Integrated Circuit Design
15
(a) The 4004 microprocessor
Standard Cell Module
Memory Module
(b) The Pentium ® 4 microprocessor
Figure 1.5 Comparing the design methodologies of the Intel 4004 (1971) and Pentium ® 4 (2000
microprocessors (reprinted with permission from Intel).
chapter1.fm Page 16 Friday, January 18, 2002 8:58 AM
INTRODUCTION
16
Chapter 1
Typically used abstraction levels in digital circuit design are, in order of increasing
abstraction, the device, circuit, gate, functional module (e.g., adder) and system levels
(e.g., processor), as illustrated in Figure 1.6. A semiconductor device is an entity with a
SYSTEM
MODULE
+
GATE
CIRCUIT
DEVICE
G
D
S
n
Figure 1.6
+
n
+
Design abstraction levels in digital circuits.
very complex behavior. No circuit designer will ever seriously consider the solid-state
physics equations governing the behavior of the device when designing a digital gate.
Instead he will use a simplified model that adequately describes the input-output behavior
of the transistor. For instance, an AND gate is adequately described by its Boolean expression (Z = A.B), its bounding box, the position of the input and output terminals, and the
delay between the inputs and the output.
This design philosophy has been the enabler for the emergence of elaborate computer-aided design (CAD) frameworks for digital integrated circuits; without it the current
design complexity would not have been achievable. Design tools include simulation at the
various complexity levels, design verification, layout generation, and design synthesis. An
overview of these tools and design methodologies is given in Chapter 8 of this textbook.
Furthermore, to avoid the redesign and reverification of frequently used cells such
as basic gates and arithmetic and memory modules, designers most often resort to cell
libraries. These libraries contain not only the layouts, but also provide complete documentation and characterization of the behavior of the cells. The use of cell libraries is, for
chapter1.fm Page 17 Friday, January 18, 2002 8:58 AM
Section 1.2
Issues in Digital Integrated Circuit Design
17
instance, apparent in the layout of the Pentium ® 4 processor (Figure 1.5b). The integer
and floating-point unit, just to name a few, contain large sections designed using the socalled standard cell approach. In this approach, logic gates are placed in rows of cells of
equal height and interconnected using routing channels. The layout of such a block can be
generated automatically given that a library of cells is available.
The preceding analysis demonstrates that design automation and modular design
practices have effectively addressed some of the complexity issues incurred in contemporary digital design. This leads to the following pertinent question. If design automation
solves all our design problems, why should we be concerned with digital circuit design at
all? Will the next-generation digital designer ever have to worry about transistors or parasitics, or is the smallest design entity he will ever consider the gate and the module?
The truth is that the reality is more complex, and various reasons exist as to why an
insight into digital circuits and their intricacies will still be an important asset for a long
time to come.
• First of all, someone still has to design and implement the module libraries. Semiconductor technologies continue to advance from year to year. Until one has developed a fool-proof approach towards “porting” a cell from one technology to another,
each change in technology—which happens approximately every two
years—requires a redesign of the library.
• Creating an adequate model of a cell or module requires an in-depth understanding
of its internal operation. For instance, to identify the dominant performance parameters of a given design, one has to recognize the critical timing path first.
• The library-based approach works fine when the design constraints (speed, cost or
power) are not stringent. This is the case for a large number of application-specific
designs, where the main goal is to provide a more integrated system solution, and
performance requirements are easily within the capabilities of the technology.
Unfortunately for a large number of other products such as microprocessors, success
hinges on high performance, and designers therefore tend to push technology to its
limits. At that point, the hierarchical approach tends to become somewhat less
attractive. To resort to our previous analogy to software methodologies, a programmer tends to “customize” software routines when execution speed is crucial; compilers—or design tools—are not yet to the level of what human sweat or ingenuity
can deliver.
• Even more important is the observation that the abstraction-based approach is only
correct to a certain degree. The performance of, for instance, an adder can be substantially influenced by the way it is connected to its environment. The interconnection wires themselves contribute to delay as they introduce parasitic capacitances,
resistances and even inductances. The impact of the interconnect parasitics is bound
to increase in the years to come with the scaling of the technology.
• Scaling tends to emphasize some other deficiencies of the abstraction-based model.
Some design entities tend to be global or external (to resort anew to the software
analogy). Examples of global factors are the clock signals, used for synchronization
in a digital design, and the supply lines. Increasing the size of a digital design has a
chapter1.fm Page 18 Friday, January 18, 2002 8:58 AM
INTRODUCTION
18
Chapter 1
profound effect on these global signals. For instance, connecting more cells to a supply line can cause a voltage drop over the wire, which, in its turn, can slow down all
the connected cells. Issues such as clock distribution, circuit synchronization, and
supply-voltage distribution are becoming more and more critical. Coping with them
requires a profound understanding of the intricacies of digital circuit design.
• Another impact of technology evolution is that new design issues and constraints
tend to emerge over time. A typical example of this is the periodical reemergence of
power dissipation as a constraining factor, as was already illustrated in the historical
overview. Another example is the changing ratio between device and interconnect
parasitics. To cope with these unforeseen factors, one must at least be able to model
and analyze their impact, requiring once again a profound insight into circuit topology and behavior.
• Finally, when things can go wrong, they do. A fabricated circuit does not always
exhibit the exact waveforms one might expect from advance simulations. Deviations
can be caused by variations in the fabrication process parameters, or by the inductance of the package, or by a badly modeled clock signal. Troubleshooting a design
requires circuit expertise.
For all the above reasons, it is my belief that an in-depth knowledge of digital circuit
design techniques and approaches is an essential asset for a digital-system designer. Even
though she might not have to deal with the details of the circuit on a daily basis, the understanding will help her to cope with unexpected circumstances and to determine the dominant effects when analyzing a design.
Example 1.1 Clocks Defy Hierarchy
To illustrate some of the issues raised above, let us examine the impact of deficiencies in one
of the most important global signals in a design, the clock. The function of the clock signal in
a digital design is to order the multitude of events happening in the circuit. This task can be
compared to the function of a traffic light that determines which cars are allowed to move. It
also makes sure that all operations are completed before the next one starts—a traffic light
should be green long enough to allow a car or a pedestrian to cross the road. Under ideal circumstances, the clock signal is a periodic step waveform with transitions synchronized
throughout the designed circuit (Figure 1.7a). In light of our analogy, changes in the traffic
lights should be synchronized to maximize throughput while avoiding accidents. The importance of the clock alignment concept is illustrated with the example of two cascaded registers,
both operating on the rising edge of the clock φ (Figure 1.7b). Under normal operating conditions, the input In gets sampled into the first register on the rising edge of φ and appears at the
output exactly one clock period later. This is confirmed by the simulations shown in Figure
1.8c (signal Out).
Due to delays associated with routing the clock wires, it may happen that the clocks
become misaligned with respect to each other. As a result, the registers are interpreting time
indicated by the clock signal differently. Consider the case that the clock signal for the second
register is delayed—or skewed—by a value δ. The rising edge of the delayed clock φ′ will
postpone the sampling of the input of the second register. If the time it takes to propagate the
output of the first register to the input of the second is smaller than the clock delay, the latter
will sample the wrong value. This causes the output to change prematurely, as clearly illustrated in the simulation, where the signal Out′ goes high at the first rising edge of φ′ instead of
chapter1.fm Page 19 Friday, January 18, 2002 8:58 AM
Section 1.2
Issues in Digital Integrated Circuit Design
19
In
3
φ (Volt)
t (nsec)
(a) Ideal clock waveform
Volt
2
φ
φ′
1
0
In
skew
skew
φ
REGISTER
3
Volt
2
Out’
Out
φ′
1
REGISTER
0
Out
(b) Two cascaded registers
Figure 1.7
time
(c) Simulated waveforms
Impact of clock misalignment.
the second one. In terms of our traffic analogy, cars of a first traffic light hit the cars of the
next light that have not left yet.
Clock misalignment, or clock skew, as it is normally called, is an important example of
how global signals may influence the functioning of a hierarchically designed system. Clock
skew is actually one of the most critical design problems facing the designers of large, highperformance systems.
Example 1.2 Power Distribution Networks Defy Hierarchy
While the clock signal is one example of a global signal that crosses the chip hierarchy
boundaries, the power distribution network represents another. A digital system requires a
stable DC voltage to be supplied to the individual gates. To ensure proper operation, this
voltage should be stable within a few hundred millivolts. The power distribution system
has to provide this stable voltage in the presence of very large current variations. The
resistive nature of the on-chip wires and the inductance of the IC package pins make this a
difficult proposition. For example, the average DC current to be supplied to a 100 W-1V
microprocessor equals 100 A! The peak current can easily be twice as large, and current
demand can readily change from almost zero to this peak value over a short time—in the
range of 1 nsec or less. This leads to a current variation of 100 GA/sec, which is a truly
astounding number.
Consider the problem of the resistance of power-distribution wires. A current of 1 A
running through a wire with a resistance of 1 Ω causes a voltage drop of 1V. With supply
voltages of modern digital circuits ranging between 1.2 and 2.5 V, such a drop is unaccept-
chapter1.fm Page 20 Friday, January 18, 2002 8:58 AM
INTRODUCTION
20
Block A
Block B
(a) Routing through the block
Block A
Chapter 1
Block B
(b) Routing around the block
Figure 1.8 Power distribution network design.
able. Making the wires wider reduces the resistance, and hence the voltage drop. While
this sizing of the power network is relatively simple in a flat design approach, it is a lot
more complex in a hierarchical design. For example, consider the two blocks below in
Figure 1.8a [Saleh01]. If power distribution for Block A is examined in isolation, the additional loading due to the presence of Block B is not taken into account. If power is routed
through Block A to Block B, a larger IR drop will occur in Block B since power is also
being consumed by Block A before it reaches Block B.
Since the total IR drop is based on the resistance seen from the pin to the block, one
could route around the block and feed power to each block separately, as shown in Figure
1.8b. Ideally, the main trunks should be large enough to handle all the current flowing
through separate branches. Although routing power this way is easier to control and maintain, it also requires more area to implement. The large metal trunks of power have to be
sized to handle all the current for each block. This requirement forces designers to set
aside area for power busing that takes away from the available routing area.
As more and more blocks are added, the complex interactions between the blocks
determine the actual voltage drops. For instance, it is not always easy to determine which
way the current will flow when multiple parallel paths are available between the power
source and the consuming gate. Also, currents into the different modules do rarely peak at
the same time. All these considerations make the design of the power-distribution a challenging job. It requires a design methodology approach that supersedes the artificial
boundaries imposed by hierarchical design.
The purpose of this textbook is to provide a bridge between the abstract vision of
digital design and the underlying digital circuit and its peculiarities. While starting from a
solid understanding of the operation of electronic devices and an in-depth analysis of the
nucleus of digital design—the inverter—we will gradually channel this knowledge into
the design of more complex entities, such as complex gates, datapaths, registers, controllers, and memories. The persistent quest for a designer when designing each of the mentioned modules is to identify the dominant design parameters, to locate the section of the
design he should focus his optimizations on, and to determine the specific properties that
make the module under investigation (e.g., a memory) different from any others.
chapter1.fm Page 21 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
21
The text also addresses other compelling (global) issues in modern digital circuit
design such as power dissipation, interconnect, timing, and synchronization.
1.3
Quality Metrics of a Digital Design
This section defines a set of basic properties of a digital design. These properties help to
quantify the quality of a design from different perspectives: cost, functionality, robustness,
performance, and energy consumption. Which one of these metrics is most important
depends upon the application. For instance, pure speed is a crucial property in a compute
server. On the other hand, energy consumption is a dominant metric for hand-held mobile
applications such as cell phones. The introduced properties are relevant at all levels of the
design hierarchy, be it system, chip, module, and gate. To ensure consistency in the definitions throughout the design hierarchy stack, we propose a bottom-up approach: we start
with defining the basic quality metrics of a simple inverter, and gradually expand these to
the more complex functions such as gate, module, and chip.
1.3.1
Cost of an Integrated Circuit
The total cost of any product can be separated into two components: the recurring
expenses or the variable cost, and the non-recurring expenses or the fixed cost.
Fixed Cost
The fixed cost is independent of the sales volume, the number of products sold. An important component of the fixed cost of an integrated circuit is the effort in time and manpower it takes to produce the design. This design cost is strongly influenced by the complexity of the design, the aggressiveness of the specifications, and the productivity of the
designer. Advanced design methodologies that automate major parts of the design process
can help to boost the latter. Bringing down the design cost in the presence of an everincreasing IC complexity is one of the major challenges that is always facing the semiconductor industry.
Additionally, one has to account for the indirect costs, the company overhead that
cannot be billed directly to one product. It includes amongst others the company’s
research and development (R&D), manufacturing equipment, marketing, sales, and building infrastructure.
Variable Cost
This accounts for the cost that is directly attributable to a manufactured product, and is
hence proportional to the product volume. Variable costs include the costs of the parts
used in the product, assembly costs, and testing costs. The total cost of an integrated circuit is now
fixed cost
cost per IC = variable cost per IC + -----------------------
volume
(1.1)
chapter1.fm Page 22 Friday, January 18, 2002 8:58 AM
INTRODUCTION
22
Chapter 1
Individual die
Figure 1.9 Finished wafer. Each
square represents a die - in this case
the AMD Duron™ microprocessor
(Reprinted with permission from AMD).
The impact of the fixed cost is more pronounced for small-volume products. This also
explains why it makes sense to have large design team working for a number of years on a
hugely successful product such as a microprocessor.
While the cost of producing a single transistor has dropped exponentially over the
past decades, the basic variable-cost equation has not changed:
of die + cost of die test + cost of packaging-----------------------------------------------------------------------------------------------------------------variable cost = cost
final test yield
(1.2)
As will be elaborated on in Chapter 2, the IC manufacturing process groups a number of
identical circuits onto a single wafer (Figure 1.9). Upon completion of the fabrication, the
wafer is chopped into dies, which are then individually packaged after being tested. We
will focus on the cost of the dies in this discussion. The cost of packaging and test is the
topic of later chapters.
The die cost depends upon the number of good die on a wafer, and the percentage of
those that are functional. The latter factor is called the die yield.
cost of wafer
cost of die = ------------------------------------------------------------dies per wafer × die yield
(1.3)
The number of dies per wafer is, in essence, the area of the wafer divided by the die
area.The actual situation is somewhat more complicated as wafers are round, and chips are
square. Dies around the perimeter of the wafer are therefore lost. The size of the wafer has
been steadily increasing over the years, yielding more dies per fabrication run. Eq. (1.3)
also presents the first indication that the cost of a circuit is dependent upon the chip
area—increasing the chip area simply means that less dies fit on a wafer.
The actual relation between cost and area is more complex, and depends upon the
die yield. Both the substrate material and the manufacturing process introduce faults that
can cause a chip to fail. Assuming that the defects are randomly distributed over the wafer,
and that the yield is inversely proportional to the complexity of the fabrication process, we
obtain the following expression of the die yield:
chapter1.fm Page 23 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
23
defects per unit area × die area – α
die yield = 1 + -------------------------------------------------------------------------
α
(1.4)
α is a parameter that depends upon the complexity of the manufacturing process, and is
roughly proportional to the number of masks. α = 3 is a good estimate for today’s complex
CMOS processes. The defects per unit area is a measure of the material and process
induced faults. A value between 0.5 and 1 defects/cm2 is typical these days, but depends
strongly upon the maturity of the process.
Example 1.3 Die Yield
Assume a wafer size of 12 inch, a die size of 2.5 cm2, 1 defects/cm2, and α = 3. Determine the
die yield of this CMOS process run.
The number of dies per wafer can be estimated with the following expression, which
takes into account the lost dies around the perimeter of the wafer.
2
× wafer diameter
π × ( wafer diameter ⁄ 2 ) – π
--------------------------------------------dies per wafer = ----------------------------------------------------------die area
2 × die area
This means 252 (= 296 - 44) potentially operational dies for this particular example. The die
yield can be computed with the aid of Eq. (1.4), and equals 16%! This means that on the average only 40 of the dies will be fully functional.
The bottom line is that the number of functional of dies per wafer, and hence the
cost per die is a strong function of the die area. While the yield tends to be excellent for the
smaller designs, it drops rapidly once a certain threshold is exceeded. Bearing in mind the
equations derived above and the typical parameter values, we can conclude that die costs
are proportional to the fourth power of the area:
cost of die = f ( die area )
4
(1.5)
The area is a function that is directly controllable by the designer(s), and is the prime metric for cost. Small area is hence a desirable property for a digital gate. The smaller the
gate, the higher the integration density and the smaller the die size. Smaller gates furthermore tend to be faster and consume less energy, as the total gate capacitance—which is
one of the dominant performance parameters—often scales with the area.
The number of transistors in a gate is indicative for the expected implementation
area. Other parameters may have an impact, though. For instance, a complex interconnect
pattern between the transistors can cause the wiring area to dominate. The gate complexity, as expressed by the number of transistors and the regularity of the interconnect structure, also has an impact on the design cost. Complex structures are harder to implement
and tend to take more of the designers valuable time. Simplicity and regularity is a precious property in cost-sensitive designs.
1.3.2
Functionality and Robustness
A prime requirement for a digital circuit is, obviously, that it performs the function it is
designed for. The measured behavior of a manufactured circuit normally deviates from the
chapter1.fm Page 24 Friday, January 18, 2002 8:58 AM
INTRODUCTION
24
Chapter 1
expected response. One reason for this aberration are the variations in the manufacturing
process. The dimensions, threshold voltages, and currents of an MOS transistor vary
between runs or even on a single wafer or die. The electrical behavior of a circuit can be
profoundly affected by those variations. The presence of disturbing noise sources on or off
the chip is another source of deviations in circuit response. The word noise in the context
of digital circuits means “unwanted variations of voltages and currents at the logic
nodes.” Noise signals can enter a circuit in many ways. Some examples of digital noise
sources are depicted in Figure 1.10. For instance, two wires placed side by side in an integrated circuit form a coupling capacitor and a mutual inductance. Hence, a voltage or current change on one of the wires can influence the signals on the neighboring wire. Noise
on the power and ground rails of a gate also influences the signal levels in the gate.
Most noise in a digital system is internally generated, and the noise value is proportional to the signal swing. Capacitive and inductive cross talk, and the internally-generated
power supply noise are examples of such. Other noise sources such as input power supply
noise are external to the system, and their value is not related to the signal levels. For these
sources, the noise level is directly expressed in Volt or Ampere. Noise sources that are a
function of the signal level are better expressed as a fraction or percentage of the signal
level. Noise is a major concern in the engineering of digital circuits. How to cope with all
these disturbances is one of the main challenges in the design of high-performance digital
circuits and is a recurring topic in this book.
VDD
v(t)
i(t)
(a) Inductive coupling
(b) Capacitive coupling
Figure 1.10 Noise sources in digital circuits.
(c) Power and ground
noise
The steady-state parameters (also called the static behavior) of a gate measure how
robust the circuit is with respect to both variations in the manufacturing process and noise
disturbances. The definition and derivation of these parameters requires a prior understanding of how digital signals are represented in the world of electronic circuits.
Digital circuits (DC) perform operations on logical (or Boolean) variables. A logical
variable x can only assume two discrete values:
x ∈ {0,1}
As an example, the inversion (i.e., the function that an inverter performs) implements the
following compositional relationship between two Boolean variables x and y:
y = x: {x = 0 ⇒ y = 1; x = 1 ⇒ y = 0}
(1.6)
chapter1.fm Page 25 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
25
A logical variable is, however, a mathematical abstraction. In a physical implementation, such a variable is represented by an electrical quantity. This is most often a node
voltage that is not discrete but can adopt a continuous range of values. This electrical voltage is turned into a discrete variable by associating a nominal voltage level with each logic
state: 1 ⇔ VOH, 0 ⇔ VOL, where VOH and VOL represent the high and the low logic levels,
respectively. Applying VOH to the input of an inverter yields VOL at the output and vice
versa. The difference between the two is called the logic or signal swing Vsw.
V OH = ( V OL )
V OL = ( V OH )
(1.7)
The Voltage-Transfer Characteristic
Assume now that a logical variable in serves as the input to an inverting gate that produces
the variable out. The electrical function of a gate is best expressed by its voltage-transfer
characteristic (VTC) (sometimes called the DC transfer characteristic), which plots the
output voltage as a function of the input voltage Vout = f(Vin). An example of an inverter
VTC is shown in Figure 1.11. The high and low nominal voltages, VOH and VOL, can
readily be identified—VOH = f(VOL) and VOL = f(VOH). Another point of interest of the
VTC is the gate or switching threshold voltage VM (not to be confused with the threshold
voltage of a transistor), that is defined as VM = f(VM). VM can also be found graphically at
the intersection of the VTC curve and the line given by Vout = Vin. The gate threshold voltage presents the midpoint of the switching characteristics, which is obtained when the output of a gate is short-circuited to the input. This point will prove to be of particular interest
when studying circuits with feedback (also called sequential circuits).
Vout
VOH
f
Vout = Vin
V
M
VOL
VOL
VOH
Vin
Figure 1.11 Inverter voltage-transfer
characteristic.
Even if an ideal nominal value is applied at the input of a gate, the output signal
often deviates from the expected nominal value. These deviations can be caused by noise
or by the loading on the output of the gate (i.e., by the number of gates connected to the
output signal). Figure 1.12a illustrates how a logic level is represented in reality by a range
of acceptable voltages, separated by a region of uncertainty, rather than by nominal levels
chapter1.fm Page 26 Friday, January 18, 2002 8:58 AM
INTRODUCTION
26
Chapter 1
alone. The regions of acceptable high and low voltages are delimited by the VIH and VIL
voltage levels, respectively. These represent by definition the points where the gain
(= dVout / dVin) of the VTC equals −1 as shown in Figure 1.12b. The region between VIH
and VIL is called the undefined region (sometimes also referred to as transition width, or
TW). Steady-state signals should avoid this region if proper circuit operation is to be
ensured.
Noise Margins
For a gate to be robust and insensitive to noise disturbances, it is essential that the “0” and
“1” intervals be as large as possible. A measure of the sensitivity of a gate to noise is given
by the noise margins NML (noise margin low) and NMH (noise margin high), which quantize the size of the legal “0” and “1”, respectively, and set a fixed maximum threshold on
the noise value:
NM L = V IL – V OL
(1.8)
NM H = V OH – V IH
The noise margins represent the levels of noise that can be sustained when gates are cascaded as illustrated in Figure 1.13. It is obvious that the margins should be larger than 0
for a digital circuit to be functional and by preference should be as large as possible.
Regenerative Property
A large noise margin is a desirable, but not sufficient requirement. Assume that a signal is
disturbed by noise and differs from the nominal voltage levels. As long as the signal is
within the noise margins, the following gate continues to function correctly, although its
output voltage varies from the nominal one. This deviation is added to the noise injected at
the output node and passed to the next gate. The effect of different noise sources may
accumulate and eventually force a signal level into the undefined region. This, fortunately,
does not happen if the gate possesses the regenerative property, which ensures that a dis-
“1”
VOH
VIH
Vout
VOH
Slope = -1
Undefined
Region
“0”
VIL
VOL
(a) Relationship between voltage and logic levels
Figure 1.12 Mapping logic levels to the voltage domain.
Slope = -1
VOL
VIL
VIH
(b) Definition of VIH and VIL
Vin
chapter1.fm Page 27 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
27
“1”
VOH
NMH
VIH
Undefined
region
VIL
NML
VOL
“0”
Gate output
Gate input
Stage M
Stage M + 1
Figure 1.13 Cascaded inverter gates:
definition of noise margins.
turbed signal gradually converges back to one of the nominal voltage levels after passing
through a number of logical stages. This property can be understood as follows:
An input voltage vin (vin ∈ “0”) is applied to a chain of N inverters (Figure 1.14a).
Assuming that the number of inverters in the chain is even, the output voltage vout (N →
∞) will equal VOL if and only if the inverter possesses the regenerative property. Similarly,
when an input voltage vin (vin ∈ “1”) is applied to the inverter chain, the output voltage
will approach the nominal value VOH.
…
v1
v0
v2
v3
v4
v5
v6
(a) A chain of inverters
V (Volt)
5
v0
3
v1
1
–1
(b) Simulated response of
chain of MOS inverters
0
2
4
v2
6
8
10
t (nsec)
Figure 1.14
The regenerative property.
Example 1.4 Regenerative property
The concept of regeneration is illustrated in Figure 1.14b, which plots the simulated transient
response of a chain of CMOS inverters. The input signal to the chain is a step-waveform with
chapter1.fm Page 28 Friday, January 18, 2002 8:58 AM
INTRODUCTION
28
Chapter 1
a degraded amplitude, which could be caused by noise. Instead of swinging from rail to rail,
v0 only extends between 2.1 and 2.9 V. From the simulation, it can be observed that this deviation rapidly disappears, while progressing through the chain; v1, for instance, extends from
0.6 V to 4.45 V. Even further, v2 already swings between the nominal VOL and VOH. The
inverter used in this example clearly possesses the regenerative property.
The conditions under which a gate is regenerative can be intuitively derived by analyzing a simple case study. Figure 1.15(a) plots the VTC of an inverter Vout = f(Vin) as well
as its inverse function finv(), which reverts the function of the x- and y-axis and is defined
as follows:
in = f ( out ) ⇒ in = finv ( out )
out
(1.9)
out
v3
finv(v)
f(v)
v1
v1
v3
finv(v)
v2
v0
in
(a) Regenerative gate
f(v)
v0
v2
in
(b) Nonregenerative gate
Figure 1.15 Conditions for regeneration.
Assume that a voltage v0, deviating from the nominal voltages, is applied to the first
inverter in the chain. The output voltage of this inverter equals v1 = f(v0) and is applied to
the next inverter. Graphically this corresponds to v1 = finv(v2). The signal voltage gradually converges to the nominal signal after a number of inverter stages, as indicated by the
arrows. In Figure 1.15(b) the signal does not converge to any of the nominal voltage levels
but to an intermediate voltage level. Hence, the characteristic is nonregenerative. The difference between the two cases is due to the gain characteristics of the gates. To be regenerative, the VTC should have a transient region (or undefined region) with a gain greater
than 1 in absolute value, bordered by the two legal zones, where the gain should be
smaller than 1. Such a gate has two stable operating points. This clarifies the definition of
the VIH and the VIL levels that form the boundaries between the legal and the transient
zones.
Noise Immunity
While the noise margin is a meaningful means for measuring the robustness of a circuit
against noise, it is not sufficient. It expresses the capability of a circuit to “overpower” a
chapter1.fm Page 29 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
29
noise source. Noise immunity, on the other hand, expresses the ability of the system to process and transmit information correctly in the presence of noise [Dally98]. Many digital
circuits with low noise margins have very good noise immunity because they reject a
noise source rather than overpower it. These circuits have the property that only a small
fraction of a potentially-damaging noise source is coupled to the important circuit nodes.
More precisely, the transfer function between noise source and signal node is far smaller
than 1. Circuits that do not posses this property are susceptible to noise.
To study the noise immunity of a gate, we have to construct a noise budget that allocates the power budget to the various noise sources. As discussed earlier, the noise sources
can be divided into sources that are
• proportional to the signal swing Vsw. The impact on the signal node is expressed as g
Vsw.
• fixed. The impact on the signal node equals f VNf, with Vnf the amplitude of the noise
source, and f the transfer function from noise to signal node.
We assume, for the sake of simplicity, that the noise margin equals half the signal swing
(for both H and L). To operate correctly, the noise margin has to be larger than the sum of
the coupled noise values.
V sw
V NM = -------≥
2
∑f V
i
Nfi
+
∑g V
j
sw
(1.10)
j
i
Given a set of noise sources, we can derive the minimum signal swing necessary for the
system to be operational,
2
∑f V
i
Nfi
V sw ≥ ------------------------1 – 2 gj
i
∑
(1.11)
j
This makes it clear that the signal swing (and the noise margin) has to be large enough to
overpower the impact of the fixed sources (f VNf). On the other hand, the sensitivity to
internal sources depends primarily upon the noise suppressing capabilities of the gate, this
is the proportionality or gain factors gj. In the presence of large gain factors, increasing the
signal swing does not do any good to suppress noise, as the noise increases proportionally.
In later chapters, we will discuss some differential logic families that suppress most of the
internal noise, and hence can get away with very small noise margins and signal swings.
Directivity
The directivity property requires a gate to be unidirectional, that is, changes in an output
level should not appear at any unchanging input of the same circuit. If not, an output-signal transition reflects to the gate inputs as a noise signal, affecting the signal integrity.
In real gate implementations, full directivity can never be achieved. Some feedback
of changes in output levels to the inputs cannot be avoided. Capacitive coupling between
inputs and outputs is a typical example of such a feedback. It is important to minimize
these changes so that they do not affect the logic levels of the input signals.
chapter1.fm Page 30 Friday, January 18, 2002 8:58 AM
INTRODUCTION
30
Chapter 1
Fan-In and Fan-Out
The fan-out denotes the number of load gates N that are connected to the output of the
driving gate (Figure 1.16). Increasing the fan-out of a gate can affect its logic output levels. From the world of analog amplifiers, we know that this effect is minimized by making
the input resistance of the load gates as large as possible (minimizing the input currents)
and by keeping the output resistance of the driving gate small (reducing the effects of load
currents on the output voltage). When the fan-out is large, the added load can deteriorate
the dynamic performance of the driving gate. For these reasons, many generic and library
components define a maximum fan-out to guarantee that the static and dynamic performance of the element meet specification.
The fan-in of a gate is defined as the number of inputs to the gate (Figure 1.16b).
Gates with large fan-in tend to be more complex, which often results in inferior static and
dynamic properties.
M
N
(b) Fan-in M
(a) Fan-out N
Figure 1.16 Definition of fan-out and fanin of a digital gate.
The Ideal Digital Gate
Based on the above observations, we can define the ideal digital gate from a static perspective. The ideal inverter model is important because it gives us a metric by which we
can judge the quality of actual implementations.
Its VTC is shown in Figure 1.17 and has the following properties: infinite gain in the
transition region, and gate threshold located in the middle of the logic swing, with high
and low noise margins equal to half the swing. The input and output impedances of the
ideal gate are infinity and zero, respectively (i.e., the gate has unlimited fan-out). While
this ideal VTC is unfortunately impossible in real designs, some implementations, such as
the static CMOS inverter, come close.
Example 1.5 Voltage-Transfer Characteristic
Figure 1.18 shows an example of a voltage-transfer characteristic of an actual, but outdated
gate structure (as produced by SPICE in the DC analysis mode). The values of the dc-parameters are derived from inspection of the graph.
chapter1.fm Page 31 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
31
Vout
g = -∞
Figure 1.17
Vin
VOH = 3.5 V;
VIH = 2.35 V;
Ideal voltage-transfer characteristic.
VOL = 0.45 V
VIL = 0.66 V
VM = 1.64 V
NMH = 1.15 V; NML = 0.21 V
The observed transfer characteristic, obviously, is far from ideal: it is asymmetrical,
has a very low value for NML, and the voltage swing of 3.05 V is substantially below the maximum obtainable value of 5 V (which is the value of the supply voltage for this design).
5.0
Vout (V)
4.0
NML
3.0
2.0
VM
NMH
1.0
0.0
1.0
2.0
3.0
Vin (V)
1.3.3
4.0
5.0
Figure 1.18 Voltage-transfer
characteristic of an NMOS
inverter of the 1970s.
Performance
From a system designers perspective, the performance of a digital circuit expresses the
computational load that the circuit can manage. For instance, a microprocessor is often
characterized by the number of instructions it can execute per second. This performance
chapter1.fm Page 32 Friday, January 18, 2002 8:58 AM
INTRODUCTION
32
Chapter 1
metric depends both on the architecture of the processor—for instance, the number of
instructions it can execute in parallel—, and the actual design of logic circuitry. While the
former is crucially important, it is not the focus of this text book. We refer the reader to the
many excellent books on this topic [for instance, Hennessy96]. When focusing on the pure
design, performance is most often expressed by the duration of the clock period (clock
cycle time), or its rate (clock frequency). The minimum value of the clock period for a
given technology and design is set by a number of factors such as the time it takes for the
signals to propagate through the logic, the time it takes to get the data in and out of the
registers, and the uncertainty of the clock arrival times. Each of these topics will be discussed in detail on the course of this text book. At the core of the whole performance analysis, however, lays the performance of an individual gate.
The propagation delay tp of a gate defines how quickly it responds to a change at its
input(s). It expresses the delay experienced by a signal when passing through a gate. It is
measured between the 50% transition points of the input and output waveforms, as shown
in Figure 1.19 for an inverting gate.2 Because a gate displays different response times for
rising or falling input waveforms, two definitions of the propagation delay are necessary.
The tpLH defines the response time of the gate for a low to high (or positive) output transition, while tpHL refers to a high to low (or negative) transition. The propagation delay tp is
defined as the average of the two.
t pLH + t pHL
t p = ------------------------2
(1.12)
Vin
50%
t
tpHL
tpLH
Vout
90%
50%
10%
tf
t
tr
Figure 1.19 Definition of propagation
delays and rise and fall times.
2
The 50% definition is inspired the assumption that the switching threshold VM is typically located in the
middle of the logic swing.
chapter1.fm Page 33 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
33
CAUTION: : Observe that the propagation delay tp, in contrast to tpLH and tpHL, is an
artificial gate quality metric, and has no physical meaning per se. It is mostly used to compare different semiconductor technologies, or logic design styles.
The propagation delay is not only a function of the circuit technology and topology,
but depends upon other factors as well. Most importantly, the delay is a function of the
slopes of the input and output signals of the gate. To quantify these properties, we introduce the rise and fall times tr and tf , which are metrics that apply to individual signal
waveforms rather than gates (Figure 1.19), and express how fast a signal transits between
the different levels. The uncertainty over when a transition actually starts or ends is
avoided by defining the rise and fall times between the 10% and 90% points of the waveforms, as shown in the Figure. The rise/fall time of a signal is largely determined by the
strength of the driving gate, and the load presented by the node itself, which sums the contributions of the connecting gates (fan-out) and the wiring parasitics.
When comparing the performance of gates implemented in different technologies or
circuit styles, it is important not to confuse the picture by including parameters such as
load factors, fan-in and fan-out. A uniform way of measuring the tp of a gate, so that technologies can be judged on an equal footing, is desirable. The de-facto standard circuit for
delay measurement is the ring oscillator, which consists of an odd number of inverters
connected in a circular chain (Figure 1.20). Due to the odd number of inversions, this circuit does not have a stable operating point and oscillates. The period T of the oscillation is
determined by the propagation time of a signal transition through the complete chain, or
T = 2 × tp × N with N the number of inverters in the chain. The factor 2 results from the
observation that a full cycle requires both a low-to-high and a high-to-low transition. Note
that this equation is only valid for 2Ntp >> tf + tr. If this condition is not met, the circuit
might not oscillate—one “wave” of signals propagating through the ring will overlap with
a successor and eventually dampen the oscillation. Typically, a ring oscillator needs a
least five stages to be operational.
v1
v0
v0
Figure 1.20
v2
v1
v3
v4
v5
Ring oscillator circuit for propagation-delay measurement.
v5
chapter1.fm Page 34 Friday, January 18, 2002 8:58 AM
INTRODUCTION
34
Chapter 1
CAUTION: We must be extremely careful with results obtained from ring oscillator
measurements. A tp of 20 psec by no means implies that a circuit built with those gates
will operate at 50 GHz. The oscillator results are primarily useful for quantifying the differences between various manufacturing technologies and gate topologies. The oscillator
is an idealized circuit where each gate has a fan-in and fan-out of exactly one and parasitic
loads are minimal. In more realistic digital circuits, fan-ins and fan-outs are higher, and
interconnect delays are non-negligible. The gate functionality is also substantially more
complex than a simple invert operation. As a result, the achievable clock frequency on
average is 50 to a 100 times slower than the frequency predicted from ring oscillator measurements. This is an average observation; carefully optimized designs might approach the
ideal frequency more closely.
Example 1.6 Propagation Delay of First-Order RC Network
Digital circuits are often modeled as first-order RC networks of the type shown in Figure
1.21. The propagation delay of such a network is thus of considerable interest.
R
vout
vin
C
Figure 1.21
First-order RC network.
When applying a step input (with vin going from 0 to V), the transient response of this
circuit is known to be an exponential function, and is given by the following expression
(where τ = RC, the time constant of the network):
v out(t) = (1 − e−t/τ) V
(1.13)
The time to reach the 50% point is easily computed as t = ln(2)τ = 0.69τ. Similarly, it takes t
= ln(9)τ = 2.2τ to get to the 90% point. It is worth memorizing these numbers, as they are
extensively used in the rest of the text.
1.3.4
Power and Energy Consumption
The power consumption of a design determines how much energy is consumed per operation, and much heat the circuit dissipates. These factors influence a great number of critical design decisions, such as the power-supply capacity, the battery lifetime, supply-line
sizing, packaging and cooling requirements. Therefore, power dissipation is an important
property of a design that affects feasibility, cost, and reliability. In the world of high-performance computing, power consumption limits, dictated by the chip package and the heat
removal system, determine the number of circuits that can be integrated onto a single chip,
and how fast they are allowed to switch.With the increasing popularity of mobile and distributed computation, energy limitations put a firm restriction on the number of computations that can be performed given a minimum time between battery recharges.
chapter1.fm Page 35 Friday, January 18, 2002 8:58 AM
Section 1.3
Quality Metrics of a Digital Design
35
Depending upon the design problem at hand, different dissipation measures have to
be considered. For instance, the peak power Ppeak is important when studying supply-line
sizing. When addressing cooling or battery requirements, one is predominantly interested
in the average power dissipation Pav. Both measures are defined in equation Eq. (1.14):
P peak = i peak V supply = max [ p ( t ) ]
T
T
∫
∫
V supply
P av = --1- p ( t )dt = --------------- i supply ( t )dt
T
T
0
(1.14)
0
where p(t) is the instantaneous power, isupply is the current being drawn from the supply
voltage Vsupply over the interval t ∈ [0,T], and ipeak is the maximum value of isupply over that
interval.
The dissipation can further be decomposed into static and dynamic components. The
latter occurs only during transients, when the gate is switching. It is attributed to the
charging of capacitors and temporary current paths between the supply rails, and is, therefore, proportional to the switching frequency: the higher the number of switching events,
the higher the dynamic power consumption. The static component on the other hand is
present even when no switching occurs and is caused by static conductive paths between
the supply rails or by leakage currents. It is always present, even when the circuit is in
stand-by. Minimization of this consumption source is a worthwhile goal.
The propagation delay and the power consumption of a gate are related—the propagation delay is mostly determined by the speed at which a given amount of energy can be
stored on the gate capacitors. The faster the energy transfer (or the higher the power consumption), the faster the gate. For a given technology and gate topology, the product of
power consumption and propagation delay is generally a constant. This product is called
the power-delay product (or PDP) and can be considered as a quality measure for a
switching device. The PDP is simply the energy consumed by the gate per switching
event. The ring oscillator is again the circuit of choice for measuring the PDP of a logic
family.
An ideal gate is one that is fast, and consumes little energy. The energy-delay product (E-D) is a combined metric that brings those two elements together, and is often used
as the ultimate quality metric. From the above, it should be clear that the E-D is equivalent
to power-delay2.
Example 1.7 Energy Dissipation of First-Order RC Network
Let us consider again the first-order RC network shown in Figure 1.21. When applying a step
input (with Vin going from 0 to V), an amount of energy is provided by the signal source to the
network. The total energy delivered by the source (from the start of the transition to the end)
can be readily computed:
∞
∞
V
∫
∫
∫
dvout
2
- dt = ( CV ) dv out = CV
E in = i in ( t )v in ( t )dt = V C ----------dt
0
0
(1.15)
0
It is interesting to observe that the energy needed to charge a capacitor from 0 to V volt
with a step input is a function of the size of the voltage step and the capacitance, but is inde-
chapter1.fm Page 36 Friday, January 18, 2002 8:58 AM
INTRODUCTION
36
Chapter 1
pendent of the value of the resistor. We can also compute how much of the delivered energy
gets stored on the capacitor at the end of the transition.
∞
∞
∫
∫
E C = i C ( t )v out ( t )dt =
0
0
V
2
dv out
---------- v out dt = C v out dvout = CV
C ----------2
dt
∫
(1.16)
0
This is exactly half of the energy delivered by the source. For those who wonder happened with the other half—a simple analysis shows that an equivalent amount gets dissipated
as heat in the resistor during the transaction. We leave it to the reader to demonstrate that during the discharge phase (for a step from V to 0), the energy originally stored on the capacitor
gets dissipated in the resistor as well, and turned into heat.
1.4
Summary
In this introductory chapter, we learned about the history and the trends in digital circuit
design. We also introduced the important quality metrics, used to evaluate the quality of a
design: cost, functionality, robustness, performance, and energy/power dissipation. At the
end of the Chapter, you can find an extensive list of reference works that may help you to
learn more about some of the topics introduced in the course of the text.
1.5
To Probe Further
The design of digital integrated circuits has been the topic of a multitude of textbooks and
monographs. To help the reader find more information on some selected topics, an extensive list of reference works is listed below. The state-of-the-art developments in the area
of digital design are generally reported in technical journals or conference proceedings,
the most important of which are listed.
JOURNALS AND PROCEEDINGS
IEEE Journal of Solid-State Circuits
IEICE Transactions on Electronics (Japan)
Proceedings of The International Solid-State and Circuits Conference (ISSCC)
Proceedings of the VLSI Circuits Symposium
Proceedings of the Custom Integrated Circuits Conference (CICC)
European Solid-State Circuits Conference (ESSCIRC)
chapter1.fm Page 37 Friday, January 18, 2002 8:58 AM
Section 1.5
To Probe Further
37
REFERENCE BOOKS
MOS
M. Annaratone, Digital CMOS Circuit Design, Kluwer, 1986.
T. Dillinger, VLSI Engineering, Prentice Hall, 1988.
E. Elmasry, ed., Digital MOS Integrated Circuits, IEEE Press, 1981.
E. Elmasry, ed., Digital MOS Integrated Circuits II, IEEE Press, 1992.
L. Glasser and D. Dopperpuhl, The Design and Analysis of VLSI Circuits, Addison-Wesley, 1985.
A. Kang and Leblebici, CMOS Digital Integrated Circuits, 2nd Ed., McGraw-Hill, 1999.
C. Mead and L. Conway, Introduction to VLSI Systems, Addison-Wesley, 1980.
K. Martin, Digital Integrated Circuit Design, Oxford University Press, 2000.
D. Pucknell and K. Eshraghian, Basic VLSI Design, Prentice Hall, 1988.
M. Shoji, CMOS Digital Circuit Technology, Prentice Hall, 1988.
J. Uyemura, Circuit Design for CMOS VLSI, Kluwer, 1992.
H. Veendrick, MOS IC’s: From Basics to ASICS, VCH, 1992.
Weste and Eshraghian, Principles of CMOS VLSI Design, Addison-Wesley, 1985, 1993.
High-Performance Design
K. Bernstein et al, High Speed CMOS Design Styles, Kluwer Academic, 1998.
A. Chandrakasan, F. Fox, and W. Bowhill, ed., Design of High-Performance Microprocessor Circuits, IEEE Press, 2000.
M. Shoji, High-Speed Digital Circuits, Addison-Wesley, 1996.
Low-Power Design
A. Chandrakasan and R. Brodersen, ed., Low-Power Digital CMOS Design, IEEE Press, 1998.
J. Rabaey and M. Pedram, ed., Low-Power Design Methodologies, Kluwer Academic, 1996.
G. Yeap, Practical Low-Power CMOS Design, Kluwer Academic, 1998.
Memory Design
K. Itoh, VLSI Memory Chip Design, Springer, 2001.
B. Prince, Semiconductor Memories, Wiley, 1991.
B. Prince, High Performance Memories, Wiley, 1996.
D. Hodges, Semiconductor Memories, IEEE Press, 1972.
Interconnections and Packaging
H. Bakoglu, Circuits, Interconnections, and Packaging for VLSI, Addison-Wesley, 1990.
W. Dally and J. Poulton, Digital Systems Engineering, Cambridge University Press, 1998.
E. Friedman, ed., Clock Distribution Networks in VLSI Circuits and Systems, IEEE Press, 1995.
J. Lau et al, ed., Electronic Packaging: Design, Materials, Process, and Reliability, McGraw-Hill,
1998.
Design Tools and Methodologies
V. Agrawal and S. Seth, Test Generation for VLSI Chips, IEEE Press, 1988.
chapter1.fm Page 38 Friday, January 18, 2002 8:58 AM
INTRODUCTION
38
Chapter 1
D. Clein, CMOS IC Layout, Newnes, 2000.
G. De Micheli, Synthesis and Optimization of Digital Circuits, McGraw-Hill, 1994.
S. Rubin, Computer Aids for VLSI Design, Addison-Wesley, 1987.
J. Uyemura, Physical Design of CMOS Integrated Circuits Using L-Edit, PWS, 1995.
A. Vladimirescu, The Spice Book, John Wiley and Sons, 1993.
W. Wolf, Modern VLSI Design, Prentice Hall, 1998.
Bipolar and BiCMOS
A. Alvarez, BiCMOS Technology and Its Applications, Kluwer, 1989.
M. Elmasry, ed., BiCMOS Integrated Circuit Design, IEEE Press, 1994.
S. Embabi, A. Bellaouar, and M. Elmasry, Digital BiCMOS Integrated Circuit Design, Kluwer,
1993.
Lynn et al., eds., Analysis and Design of Integrated Circuits, McGraw-Hill, 1967.
General
J. Buchanan, CMOS/TTL Digital Systems Design, McGraw-Hill, 1990.
H. Haznedar, Digital Micro-Electronics, Benjamin/Cummings, 1991.
D. Hodges and H. Jackson, Analysis and Design of Digital Integrated Circuits, 2nd ed., McGrawHill, 1988.
M. Smith, Application-Specific Integrated Circuits, Addison-Wesley, 1997.
R. K. Watts, Submicron Integrated Circuits, Wiley, 1989.
REFERENCES
[Bardeen48] J. Bardeen and W. Brattain, “The Transistor, a Semiconductor Triode,” Phys. Rev.,
vol. 74, p. 230, July 15, 1948.
[Beeson62] R. Beeson and H. Ruegg, “New Forms of All Transistor Logic,” ISSCC Digest of Technical Papers, pp. 10–11, Feb. 1962.
[Dally98] B. Dally, Digital Systems Engineering, Cambridge University Press, 1998.
[Faggin72] F. Faggin, M.E. Hoff, Jr, H. Feeney, S. Mazor, M. Shima, “The MCS-4 - An LSI MicroComputer System,” 1972 IEEE Region Six Conference Record, San Diego, CA, April 19-21,
1972, pp.1-6.
[Harris56] J. Harris, “Direct-Coupled Transistor Logic Circuitry in Digital Computers,” ISSCC
Digest of Technical Papers, p. 9, Feb. 1956.
[Hart72] C. Hart and M. Slob, “Integrated Injection Logic—A New Approach to LSI,” ISSCC
Digest of Technical Papers, pp. 92–93, Feb. 1972.
[Hoff70] E. Hoff, “Silicon-Gate Dynamic MOS Crams 1,024 Bits on a Chip,” Electronics,
pp. 68–73, August 3, 1970.
[Intel01] “Moore’s Law”, http://www.intel.com/research/silicon/mooreslaw.htm
[Masaki74] A. Masaki, Y. Harada and T. Chiba, “200-Gate ECL Master-Slice LSI,” ISSCC Digest
of Technical Papers, pp. 62–63, Feb. 1974.
[Moore65] G. Moore, “Cramming more Components into Integrated Circuits,” Electronics, Vol. 38,
Nr 8, April 1965.
chapter1.fm Page 39 Friday, January 18, 2002 8:58 AM
Section 1.6
Exercises
39
[Murphy93] B. Murphy, “Perspectives on Logic and Microprocessors,” Commemorative Supplement to the Digest of Technical Papers, ISSCC Conf., pp. 49–51, San Francisco, 1993.
[Norman60] R. Norman, J. Last and I. Haas, “Solid-State Micrologic Elements,” ISSCC Digest of
Technical Papers, pp. 82–83, Feb. 1960.
[Hennessy96] J. Hennessy and D. Patterson, Computer Architecture A Quantitative Approach, Second Edition, Morgan Kaufmann Publishers, 1996
[Saleh01] R. Saleh, M. Benoit, and P, McCrorie, “Power Distribution Planning”, Simplex Solutions,
http://www.simplex.com/wt/sec.php?page_name=wp_powerplan
[Schockley49] W. Schockley, “The Theory of pn Junctions in Semiconductors and pn-Junction
Transistors,” BSTJ, vol. 28, p. 435, 1949.
[Shima74] M. Shima, F. Faggin and S. Mazor, “An N-Channel, 8-bit Single-Chip Microprocessor,”
ISSCC Digest of Technical Papers, pp. 56–57, Feb. 1974.
[Swade93] D. Swade, “Redeeming Charles Babbage’s Mechanical Computer,” Scientific American,
pp. 86–91, February 1993.
[Wanlass63] F. Wanlass, and C. Sah, “Nanowatt logic Using Field-Effect Metal-Oxide Semiconductor Triodes,” ISSCC Digest of Technical Papers, pp. 32–32, Feb. 1963.
1.6
Exercises
1.
2.
3.
4.
5.
[E, None, 1.2] Based on the evolutionary trends described in the chapter, predict the integration complexity and the clock speed of a microprocessor in the year 2015. Determine also
how much DRAM should be available on a single chip at that point in time, if Moore’s law
would still hold.
[D,
None,
1.2]
Visit
the
Intel
on-line
microprocessor
museum
(http://www.intel.com/intel/intelis/museum/exhibit/hist_micro/index.htm). While browsing
through the microprocessor hall-of-fame, determine the rate of increase in transistor counts
and clock frequencies in the 70’s, 80’s, and 90’s. Also, create a plot of the number of transistors versus technology feature size. Spend some time browsing the site. It contains a large
amount of very interesting information.
[D, None, 1.2] By scanning the literature, find the leading-edge devices at this point in time in
the following domains: microprocessor, signal processor, SRAM, and DRAM. Determine for
each of those, the number of integrated devices, the overall area and the maximum clock
speed. Evaluate the match with the trends predicted in section 1.2.
[D, None, 1.2] Find in the library the latest November issue of the Journal of Solid State Circuits. For each of the papers, determine its application class (such as microprocessor, signal
processor, DRAM, SRAM), the type of manufacturing technology used (MOS, bipolar, etc.),
the minimum feature size, the number of devices on a single die, and the maximum clock
speed. Tabulate the results along the various application classes.
[E, None, 1.2] Provide at least three examples for each of the abstraction levels described in
Figure 1.6.
chapter1.fm Page 40 Friday, January 18, 2002 8:58 AM
40
INTRODUCTION
Chapter 1
chapter2.fm Page 41 Friday, January 18, 2002 8:59 AM
CHAPTER
2
THE MANUFACTURING PROCESS
Overview of manufacturing process
n
Design rules
n
IC packaging
n
Future Trends in Integrated Circuit Technology
2.1
Introduction
2.2
Manufacturing CMOS Integrated Circuits
2.5.1
Short-Term Developments
2.2.1
The Silicon Wafer
2.5.2
In the Longer Term
2.2.2
Photolithography
2.2.3
Some Recurring Process Steps
2.2.4
Simplified CMOS Process Flow
2.3
Design Rules — The Contract between
Designer and Process Engineer
2.4
Packaging Integrated Circuits
2.4.1
Package Materials
2.4.2
Interconnect Levels
2.4.3
Thermal Considerations in Packaging
2.5
2.6
Perspective — Trends in Process Technology
Summary
41
chapter2.fm Page 42 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
42
2.1
Chapter 2
Introduction
Most digital designers will never be confronted with the details of the manufacturing process that lies at the core of the semiconductor revolution. Yet, some insight in the steps
that lead to an operational silicon chip comes in quite handy in understanding the physical
constraints that are imposed on a designer of an integrated circuit, as well as the impact of
the fabrication process on issues such as cost.
In this chapter, we briefly describe the steps and techniques used in a modern integrated circuit manufacturing process. It is not our aim to present a detailed description of
the fabrication technology, which easily deserves a complete course [Plummer00]. Rather
we aim at presenting the general outline of the flow and the interaction between the various steps. We learn that a set of optical masks forms the central interface between the
intrinsics of the manufacturing process and the design that the user wants to see transferred to the silicon fabric. The masks define the patterns that, when transcribed onto the
different layers of the semiconductor material, form the elements of the electronic devices
and the interconnecting wires. As such, these patterns have to adhere to some constraints
in terms of minimum width and separation if the resulting circuit is to be fully functional.
This collection of constraints is called the design rule set, and acts as the contract between
the circuit designer and the process engineer. If the designer adheres to these rules, he gets
a guarantee that his circuit will be manufacturable. An overview of the common design
rules, encountered in modern CMOS processes, will be given. Finally, an overview is
given of the IC packaging options. The package forms the interface between the circuit
implemented on the silicon die and the outside world, and as such has a major impact on
the performance, reliability, longevity, and cost of the integrated circuit.
2.2
Manufacturing CMOS Integrated Circuits
A simplified cross section of a typical CMOS inverter is shown in Figure 2.1. The CMOS
process requires that both n-channel (NMOS) and p-channel (PMOS) transistors be built
in the same silicon material. To accommodate both types of devices, special regions called
wells must be created in which the semiconductor material is opposite to the type of the
channel. A PMOS transistor has to be created in either an n-type substrate or an n-well,
while an NMOS device resides in either a p-type substrate or a p-well. The cross section
Figure 2.1
Cross section of an n-well CMOS process.
chapter2.fm Page 43 Friday, January 18, 2002 8:59 AM
Section 2.2
Manufacturing CMOS Integrated Circuits
43
shown in Figure 2.1 features an n-well CMOS process, where the NMOS transistors are
implemented in the p-doped substrate, and the PMOS devices are located in the n-well.
Modern processes are increasingly using a dual-well approach that uses both n- and pwells, grown on top on a epitaxial layer, as shown in Figure 2.2. We will restrict the
remainder of this discussion to the latter process (without loss of generality).
gate-oxide
Tungsten
TiSi2
AlCu
SiO2
poly
p-well
n+
SiO2
n-well
p+
p-epi
p+
Figure 2.2Cross section of modern dual-well CMOS process.
The CMOS process requires a large number of steps, each of which consists of a
sequence of basic operations. A number of these steps and/or operations are executed very
repetitively in the course of the manufacturing process. Rather than diving directly into a
description of the overall process flow, we first discuss the starting material followed by a
detailed perspective on some of the most-often recurring operations.
2.2.1
The Silicon Wafer
The base material for the manufacturing process comes
in the form of a single-crystalline, lightly doped wafer.
These wafers have typical diameters between 4 and 12
inches (10 and 30 cm, respectively) and a thickness of
at most 1 mm, and are obtained by cutting a singlecrystal ingot into thin slices (Figure 2.3). A starting
wafer of the p--type might be doped around the levels
of 2 × 1021 impurities/m3. Often, the surface of the
wafer is doped more heavily, and a single crystal epitaxial layer of the opposite type is grown over the surface before the wafers are handed to the processing
company. One important metric is the defect density of
the base material. High defect densities lead to a larger
fraction of non-functional circuits, and consequently an
increase in cost of the final product.
Figure 2.3 Single-crystal ingot and
sliced wafers (from [Fullman99]).
chapter2.fm Page 44 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
44
2.2.2
Chapter 2
Photolithography
In each processing step, a certain area on the chip is masked out using the appropriate optical mask so that a desired processing step can be selectively applied to the remaining
regions. The processing step can be any of a wide range of tasks including oxidation, etching, metal and polysilicon deposition, and ion implantation. The technique to accomplish
this selective masking, called photolithography, is applied throughout the manufacturing
process. Figure 2.4 gives a graphical overview of the different operations involved in a
typical photolitographic process. The following steps can be identified:
optical
mask
oxidation
photoresist
removal (ashing)
photoresist coating
stepper exposure
Figure 2.4 Typical operations in a single
photolithographic cycle (from [Fullman99]).
photoresist
development
acid etch
process
step
spin, rinse, dry
1. Oxidation layering — this optional step deposits a thin layer of SiO2 over the complete wafer by exposing it to a mixture of high-purity oxygen and hydrogen at
approximately 1000°C. The oxide is used as an insulation layer and also forms transistor gates.
2. Photoresist coating — a light-sensitive polymer (similar to latex) is evenly applied
while spinning the wafer to a thickness of approximately 1 µm. This material is
originally soluble in an organic solvent, but has the property that the polymers cross-
chapter2.fm Page 45 Friday, January 18, 2002 8:59 AM
Section 2.2
Manufacturing CMOS Integrated Circuits
45
link when exposed to light, making the affected regions insoluble. A photoresist of
this type is called negative. A positive photoresist has the opposite properties; originally insoluble, but soluble after exposure. By using both positive and negative
resists, a single mask can sometimes be used for two steps, making complementary
regions available for processing. Since the cost of a mask is increasing quite rapidly
with the scaling of technology, a reduction of the number of masks is surely of high
priority.
3. Stepper exposure — a glass mask (or reticle), containing the patterns that we want to
transfer to the silicon, is brought in close proximity to the wafer. The mask is
opaque in the regions that we want to process, and transparent in the others (assuming a negative photoresist). The glass mask can be thought of as the negative of one
layer of the microcircuit. The combination of mask and wafer is now exposed to
ultra-violet light. Where the mask is transparent, the photoresist becomes insoluble.
4. Photoresist development and bake — the wafers are developed in either an acid or
base solution to remove the non-exposed areas of photoresist. Once the exposed
photoresist is removed, the wafer is “soft-baked” at a low temperature to harden the
remaining photoresist.
5. Acid Etching — material is selectively removed from areas of the wafer that are not
covered by photoresist. This is accomplished through the use of many different
types of acid, base and caustic solutions as a function of the material that is to be
removed. Much of the work with chemicals takes place at large wet benches where
special solutions are prepared for specific tasks. Because of the dangerous nature of
some of these solvents, safety and environmental impact is a primary concern.
6. Spin, rinse, and dry — a special tool (called SRD) cleans the wafer with deionized
water and dries it with nitrogen. The microscopic scale of modern semiconductor
devices means that even the smallest particle of dust or dirt can destroy the circuitry.
To prevent this from happening, the processing steps are performed in ultra-clean
rooms where the number of dust particles per cubic foot of air ranges between 1 and
10. Automatic wafer handling and robotics are used whenever possible. This
explains why the cost of a state-of-the-art fabrication facility easily ranges in the
multiple billions of dollars. Even then, the wafers must be constantly cleaned to
avoid contamination, and to remove the left-over of the previous process steps.
7. Various process steps — the exposed area can now be subjected to a wide range of
process steps, such as ion implantation, plasma etching, or metal deposition. These
are the subjects of the subsequent section.
8. Photoresist removal (or ashing) — a high-temperature plasma is used to selectively
remove the remaining photoresist without damaging device layers.
We illustrate the use of the photolitographic process for one specific example, the
patterning of a layer of SiO2, in Figure 2.5. The sequence of process steps shown in the
Figure patterns exactly one layer of the semiconductor material, and may seem very complex. Yet, the reader has to bear in mind that same sequence patterns the layer of the complete surface of the wafer. It is hence a very parallel process, transferring hundreds of
chapter2.fm Page 46 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
46
Chapter 2
Chemical or plasma
etch
Si-substrate
Hardened resist
SiO2
(a) Silicon base material
Si-substrate
Photoresist
SiO2
Si-substrate
(d) After development and etching of resist,
chemical or plasma etch of SiO2
Hardened resist
SiO2
(b) After oxidation and deposition
of negative photoresist
Si-substrate
UV-light
Patterned
optical mask
(e) After etching
Exposed resist
Si-substrate
(c) Stepper exposure
SiO2
Si-substrate
(f) Final result after removal of resist
Figure 2.5 Process steps for patterning of SiO 2.
millions of patterns to the semiconductor surface simultaneously. The concurrent and scalable nature of the optolithographical process is what makes the cheap manufacturing of
complex semiconductor circuits possible, and lies at the core of the economic success of
the semiconductor industry.
The continued scaling of the minimum feature sizes in integrated circuits puts an
enormous burden on the developer of semiconductor manufacturing equipment. This is
especially true for the optolithographical process. The dimensions of the features to be
transcribed surpass the wavelengths of the optical light sources, so that achieving the necessary resolution and accuracy becomes harder and harder. So far, engineering engineering has extended the lifetime of this process at least until the 100 nm (or 0.1 µm) process
generation. Techniques such as optical-mask correction (OPC) pre-warp the drawn patterns to account for the diffraction phenomena, encountered when printing close to the
limits of optical lithography. This adds substantially to the cost of mask making. In the
foreseeable future, other solutions that offer a a finer resolution such as extreme-ultraviolet (EUV), X-ray or electron-beam may be needed. These techniques, while fully functional, are currently less attractive from an economic viewpoint.
chapter2.fm Page 47 Friday, January 18, 2002 8:59 AM
Section 2.2
2.2.3
Manufacturing CMOS Integrated Circuits
47
Some Recurring Process Steps
Diffusion and Ion Implantation
Many steps of the integrated circuit manufacturing process require a chance in the
dopant concentration of some parts of the material. The creation of the source and drain
regions, well and substrate contacts, the doping of the polysilicon, and the adjustments of
the device threshold are examples of such. There exist two approaches for introducing
these dopants—diffusion and ion implantation. In both techniques, the area to be doped is
exposed, while the rest of the wafer is coated with a layer of buffer material, typically
SiO2.
In diffusion implantation, the wafers are placed in a quartz tube embedded in a
heated furnace. A gas containing the dopant is introduced in the tube. The high temperatures of the furnace, typically 900 to 1100 °C, cause the dopants to diffuse into the
exposed surface both vertically and horizontally. The final dopant concentration is the
greatest at the surface and decreases in a gaussian profile deeper in the material.
In ion implantation, dopants are introduced as ions into the material. The ion
implantation system directs and sweeps a beam of purified ions over the semiconductor
surface. The acceleration of the ions determines how deep they will penetrate the material,
while the beam current and the exposure time determine the dosage. The ion implantation
method allows for an independent control of depth and dosage. This is the reason that ion
implantation has largely displaced diffusion in modern semiconductor manufacturing.
Ion implantation has some unfortunate side effects however, the most important one
being lattice damage. Nuclear collisions during the high energy implantation cause the
displacement of substrate atoms, leading to material defects. This problem is largely
resolved by applying a subsequent annealing step, in which the wafer is heated to around
1000°C for 15 to 30 minutes, and then allowed to cool slowly. The heating step thermally
vibrates the atoms, which allows the bonds to reform.
Deposition
Any CMOS process requires the repetitive deposition of layers of a material over
the complete wafer, to either act as buffers for a processing step, or as insulating or conducting layers. We have already discussed the oxidation process, which allows a layer of
SiO2 to be grown. Other materials require different techniques. For instance, silicon
nitride (Si3N4) is used as a sacrificial buffer material during the formation of the field
oxide and the introduction of the stopper implants. This silicon nitride is deposited everywhere using a process called chemical vapor deposition or CVD, which uses a gas-phase
reaction with energy supplied by heat at around 850°C.
Polysilicon, on the other hand, is deposited using a chemical deposition process,
which flows silane gas over the heated wafer coated with SiO2 at a temperature of approximately 650°C. The resulting reaction produces a non-crystalline or amorphous material
called polysilicon. To increase to conductivity of the material, the deposition has to be followed by an implantation step.
The Aluminum interconnect layers are typically deployed using a process known as
sputtering. The aluminum is evaporated in a vacuum, with the heat for the evaporation
chapter2.fm Page 48 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
48
Chapter 2
delivered by electron-beam or ion-beam bombarding. Other metallic interconnect materials such as Copper require different deposition techniques.
Etching
Once a material has been deposited, etching is used to selectively form patterns such
as wires and contact holes. The wet etching process was described earlier, and makes use
of acid or basic solutions. For instance, hydrofluoric acid buffered with ammonium fluoride is typically used to etch SiO2.
In recent years, dry or plasma etching has made a lot of inroad. A wafer is placed
into the etch tool's processing chamber and given a negative electrical charge. The chamber is heated to 100°C and brought to a vacuum level of 7.5 Pa, then filled with a positively charged plasma (usually a mix of nitrogen, chlorine and boron trichloride). The
opposing electrical charges cause the rapidly moving plasma molecules to align themselves in a vertical direction, forming a microscopic chemical and physical “sandblasting”
action which removes the exposed material. Plasma etching has the advantage of offering
a well-defined directionality to the etching action, creating patterns with sharp vertical
contours.
Planarization
To reliably deposit a layer of material onto the semiconductor surface, it is essential
that the surface is approximately flat. If no special steps were taken, this would definitely
not be the case in modern CMOS processes, where multiple patterned metal interconnect
layers are superimposed onto each other. Therefore, a chemical-mechanical planarization
(CMP) step is included before the deposition of an extra metal layer on top of the insulating SiO2 layer. This process uses a slurry compound—a liquid carrier with a suspended
abrasive component such as aluminum oxide or silica—to microscopically plane a device
layer and to reduce the step heights.
2.2.4
Simplified CMOS Process Flow
The gross outline of a potential CMOS process flow is given in Figure 2.6. The process
starts with the definition of the active regions, this is the regions where transistors will be
constructed. All other areas of the die will be covered with a thick layer of silicon dioxide
(SiO2), called the field oxide. This oxide acts as the insulator between neighboring
devices, and is either grown (as in the process of Figure 2.1), or deposited in etched
trenches (Figure 2.2) — hence the name trench insulation. Further insulation is provided
by the addition of a reverse-biased np-diode, formed by adding an extra p+ region, called
the channel-stop implant (or field implant) underneath the field oxide. Next, lightly doped
p- and n-wells are formed through ion implantation. To construct an NMOS transistor in a
p-well, heavily doped n-type source and drain regions are implanted (or diffused) into the
lightly doped p-type substrate. A thin layer of SiO2, called the gate oxide, separates the
region between the source and drain, and is itself covered by conductive polycrystalline
silicon (or polysilicon, for short). The conductive material forms the gate of the transistor.
PMOS transistors are constructed in an n-well in a similar fashion (just reverse n’s and
chapter2.fm Page 49 Friday, January 18, 2002 8:59 AM
Section 2.2
Manufacturing CMOS Integrated Circuits
49
Define active areas
Etch and fill trenches
Implant well regions
Deposit and pattern
polysilicon layer
Implant source and drain
regions and substrate contacts
Create contact and via windows
Deposit and pattern metal layers
Figure 2.6 Simplified process sequence for the manufacturing of a ndual-well CMOS circuit.
p’s). Multiple insulated layers of metallic (most often Aluminum) wires are deposited on
top of these devices to provide for the necessary interconnections between the transistors.
A more detailed breakdown of the flow into individual process steps and their
impact on the semiconductor material is shown graphically in Figure 2.7. While most of
the operations should be self-explanatory in light of the previous descriptions, some comments on individual operations are worthwhile. The process starts with a p-substrate surfaced with a lightly doped p-epitaxial layer (a). A thin layer of SiO2 is deposited, which
will serve as the gate oxide for the transistors, followed by a deposition of a thicker sacrificial silicon nitride layer (b). A plasma etching step using the complementary of the
active area mask creates the trenches, used for insulating the devices (c). After providing
the channel stop implant, the trenches are filled with SiO2 followed by a number of steps
to provide a flat surface (including inverse active pattern oxide etching, and chemicalmechanical planarization). At that point, the sacrificial nitride is removed (d). The n-well
mask is used to expose only the n-well areas (the rest of the wafer is covered by a thick
buffer material), after which an implant-annealing sequence is applied to adjust the welldoping. This is followed by a second implant step to adjust the threshold voltages of the
PMOS transistors. This implant only impacts the doping in the area just below the gate
oxide (e). Similar operations (using other dopants) are performed to create the p-wells,
and to adjust the thresholds of the NMOS transistors (f). A thin layer of polysilicon is
chemically deposited, and patterned with the aid of the polysilicon mask. Polysilicon is
used both as gate electrode material for the transistors as well as an interconnect medium
(g). Consecutive ion implantations are used to dope the source and drain regions of the
PMOS (p+) and NMOS (n+) transistors, respectively (h), after which the thin gate oxide
not covered by the polysilicon is etched away1. The same implants are also used to dope
1
Most modern processes also include extra implants for the creation of the lightly-doped drain regions
(LDD), and the creation of gate spacers at this point. We have omitted these for the sake of simplicity.
chapter2.fm Page 50 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
50
p-epi
p
Chapter 2
(a) Base material: p+ substrate
with p-epi layer
+
Si3N4
SiO2
p-epi
p+
(b) After deposition of gate-oxide and
sacrificial nitride (acts as a
buffer layer)
(c) After plasma etch of insulating
trenches using the inverse of
the active area mask
p+
SiO2
(d) After trench filling, CMP
planarization, and removal of
sacrificial nitride
n
(e) After n-well and
VTp adjust implants
p
(f) After p-well and
VTn adjust implants
chapter2.fm Page 51 Friday, January 18, 2002 8:59 AM
Section 2.2
Manufacturing CMOS Integrated Circuits
51
poly(silicon)
(g) After polysilicon deposition
and etch
n+
p+
(h) After n+ source/drain and
p+ source/drain implants. These
steps also dope the polysilicon.
SiO2
(i) After deposition of SiO2
insulator and contact hole etch.
Al
(j) After deposition and
patterning of first Al layer.
Al
SiO2
(k) After deposition of SiO2
insulator, etching of via’s,
deposition and patterning of
second layer of Al.
Figure 2.7 Process flow for the fabrication of an NMOS and a PMOS transistor in a dual-well CMOS process. Be
aware that the drawings are stylized for understanding, and that the aspects ratios are not proportioned to reality.
chapter2.fm Page 52 Friday, January 18, 2002 8:59 AM
52
THE MANUFACTURING PROCESS
Chapter 2
the polysilicon on the surface, reducing its resistivity. Undoped polysilicon has a very
high resistivity. Note that the polysilicon gate, which is patterned before the doping, actually defines the precise location of the channel region, and hence the location of the source
and drain regions. This procedure allows for a very precise positioning of the two regions
relative to the gate, and hence is called the self-aligned process. The process continues
with the deposition of the metallic interconnect layers. These consists of a repetition of the
following steps (i-k): deposition of the insulating material (most often SiO2), etching of
the contact or via holes, deposition of the metal (most often Aluminum and Copper,
although Tungsten is often used for the lower layers), and patterning of the metal. Intermediate planarization steps ensure that the surface remains reasonable flat, even in the
presence of multiple interconnect layers. After the last level of metal is deposited, a final
passivation or overglass is deposited for protection. This layer would be CVD SiO2,
although often an additional layer of nitride is deposited as it is more impervious to moisture. The final processing step is to etch openings to the pads used for bonding.
A cross-section of the final artifact is shown in Figure 2.8. Observe how the transistors occupy only a small fraction of the total height of the structure. The interconnect layers take up the majority of the vertical dimension.
transistor
Figure 2.8 Cross-section of state-of-the-art
CMOS process.
2.3
Design Rules — The Contract between Designer and Process Engineer
As processes become more complex, requiring the designer to understand the intricacies
of the fabrication process and interpret the relations between the different masks is a sure
road to trouble. The goal of defining a set of design rules is to allow for a ready translation
of a circuit concept into an actual geometry in silicon. The design rules act as the interface
or even the contract between the circuit designer and the process engineer.
Circuit designers in general want tighter, smaller designs, which lead to higher performance and higher circuit density. The process engineer, on the other hand, wants a
reproducible and high-yield process. Design rules are, consequently, a compromise that
attempts to satisfy both sides.
chapter2.fm Page 53 Friday, January 18, 2002 8:59 AM
Section 2.3
Design Rules — The Contract between Designer and Process Engineer
53
The design rules provide a set of guidelines for constructing the various masks
needed in the patterning process. They consist of minimum-width and minimum-spacing
constraints and requirements between objects on the same or on different layers.
The fundamental unity in the definition of a set of design rules is the minimum line
width. It stands for the minimum mask dimension that can be safely transferred to the
semiconductor material. In general, the minimum line width is set by the resolution of the
patterning process, which is most commonly based on optical lithography. More advanced
approaches use electron-beam. EUV or X-ray sources that offer a finer resolution, but are
less attractive from an economical viewpoint today.
Even for the same minimum dimension, design rules tend to differ from company to
company, and from process to process. This makes porting an existing design between different processes a time-consuming task. One approach to address this issue is to use
advanced CAD techniques, which allow for migration between compatible processes.
Another approach is to use scalable design rules. The latter approach, made popular by
Mead and Conway [Mead80], defines all rules as a function of a single parameter, most
often called λ. The rules are chosen so that a design is easily ported over a cross section of
industrial processes. Scaling of the minimum dimension is accomplished by simply
changing the value of λ. This results in a linear scaling of all dimensions. For a given process, λ is set to a specific value, and all design dimensions are consequently translated into
absolute numbers. Typically, the minimum line width of a process is set to 2λ. For
instance, for a 0.25 µm process (i.e., a process with a minimum line width of 0.25 µm), λ
equals 0.125 µm.
This approach, while attractive, suffers from some disadvantages:
1. Linear scaling is only possible over a limited range of dimensions (for instance,
between 0.25 µm and 0.18 µm). When scaling over larger ranges, the relations
between the different layers tend to vary in a nonlinear way that cannot be adequately covered by the linear scaling rules.
2. Scalable design rules are conservative. As they represent a cross section over different technologies, they have to represent the worst-case rules for the whole set. This
results in over-dimensioned and less-dense designs.
For these reasons, scalable design rules are normally avoided by industry.2 As circuit density is a prime goal in industrial designs, most semiconductor companies tend to use
micron rules, which express the design rules in absolute dimensions and can therefore
exploit the features of a given process to a maximum degree. Scaling and porting designs
between technologies under these rules is more demanding and has to be performed either
manually or using advanced CAD tools.
For this textbook, we have selected a “vanilla” 0.25 µm CMOS process as our preferred implementation medium. The rest of this section is devoted to a short introduction
and overview of the design rules of this process, which fall in the micron-rules class. A
complete design-rule set consists of the following entities: a set of layers, relations
2
While not entirely accurate, lambda rules are still useful to estimate the impact of a technology scale on
the area of a design.
chapter2.fm Page 54 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
54
Chapter 2
between objects on the same layer, and relations between objects on different layers. We
discuss each of them in sequence.
Layer Representation
The layer concept translates the intractable set of masks currently used in CMOS into a
simple set of conceptual layout levels that are easier to visualize by the circuit designer.
From a designer’s viewpoint, all CMOS designs are based on the following entities:
• Substrates and/or wells, being p-type (for NMOS devices) and n-type (for PMOS)
• Diffusion regions (n+ and p+) defining the areas where transistors can be formed.
These regions are often called the active areas. Diffusions of an inverse type are
needed to implement contacts to the wells or to the substrate. These are called select
regions.
• One or more polysilicon layers, which are used to form the gate electrodes of the
transistors (but serve as interconnect layers as well).
• A number of metal interconnect layers.
• Contact and via layers to provide interlayer connections.
A layout consists of a combination of polygons, each of which is attached to a certain
layer. The functionality of the circuit is determined by the choice of the layers, as well as
the interplay between objects on different layers. For instance, an MOS transistor is
formed by the cross section of the diffusion layer and the polysilicon layer. An interconnection between two metal layers is formed by a cross section between the two metal layers and an additional contact layer. To visualize these relations, each layer is assigned a
standard color (or stipple pattern for a black-and-white representation). The different layers used in our CMOS process are represented in Colorplate 1 (color insert).
Intralayer Constraints
A first set of rules defines the minimum dimensions of objects on each layer, as well as the
minimum spacings between objects on the same layer. All distances are expressed in µm.
These constraints are presented in a pictorial fashion in Colorplate 2.
Interlayer Constraints
Interlayer rules tend to be more complex. The fact that multiple layers are involved makes
it harder to visualize their meaning or functionality. Understanding layout requires the
capability of translating the two-dimensional picture of the layout drawing into the threedimensional reality of the actual device. This takes some practice.
We present these rules in a set of separate groupings.
1. Transistor Rules (Colorplate 3). A transistor is formed by the overlap of the active
and the polysilicon layers. From the intralayer design rules, it is already clear that
the minimum length of a transistor equals 0.24 µm (the minimum width of polysilicon), while its width is at least 0.3 µm (the minimum width of diffusion). Extra rules
chapter2.fm Page 55 Friday, January 18, 2002 8:59 AM
Section 2.3
Design Rules — The Contract between Designer and Process Engineer
55
include the spacing between the active area and the well boundary, the gate overlap
of the active area, and the active overlap of the gate.
2. Contact and Via Rules (Colorplates 2 and 4). A contact (which forms an interconnection between metal and active or polysilicon) or a via (which connects two metal
layers) is formed by overlapping the two interconnecting layers and providing a
contact hole, filled with metal, between the two. In our process, the minimum size of
the contact hole is 0.3 µm, while the polysilicon and diffusion layers have to extend
at least over 0.14 µm beyond the area of the contact hole. This sets the minimum
area of a contact to 0.44 µm × 0.44 µm. This is larger than the dimensions of a minimum-size transistor! Excessive changes between interconnect layers in routing are
thus to be avoided. The figure, furthermore, points out the minimum spacings
between contact and via holes, as well as their relationship with the surrounding layers.
Well and Substrate Contacts (Colorplate 5). For robust digital circuit design, it is
important for the well and substrate regions to be adequately connected to the supply voltages. Failing to do so results in a resistive path between the substrate contact of the transistors and the supply rails, and can lead to possibly devastating parasitic effects, such as
latchup. It is therefore advisable to provide numerous substrate (well) contacts spread over
the complete region. To establish an ohmic contact between a supply rail, implemented in
metal1, and a p-type material, a p+ diffusion region must be provided. This is enabled by
the select layer, which reverses the type of diffusion. A number of rules regarding the use
of the select layer are illustrated in Colorplate 5.
Consider an n-well process, which implements the PMOS transistors into an n-type
well diffused in a p-type material. The nominal diffusion is p+. To invert the polarity of the
diffusion, an n-select layer is provided that helps to establish the n+ diffusions for the wellcontacts in the n-region as well as the n+ source and drain regions for the NMOS transistors in the substrate.
Verifying the Layout
Ensuring that none of the design rules is violated is a fundamental requirement of the
design process. Failing to do so will almost surely lead to a nonfunctional design. Doing
so for a complex design that can contain millions of transistors is no sinecure, especially
when taking into account the complexity of some design-rule sets. While design teams in
the past used to spend numerous hours staring at room-size layout plots, most of this task
is now done by computers. Computer-aided Design-Rule Checking (called DRC) is an
integral part of the design cycle for virtually every chip produced today. A number of layout tools even perform on-line DRC and check the design in the background during the
time of conception.
Example 2.1 Layout Example
An example of a complete layout containing an inverter is shown in Figure 2.9. To help
the visualization process, a vertical cross section of the process along the design center is
included as well as a circuit schematic.
chapter2.fm Page 56 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
56
Chapter 2
VDD
GND
In
A′
A
Out
(a) Layout
A′
A
n
Field
oxide
p-substrate
n+
p+
(b) Cross section along A-A′
In
VDD
GND
Out
(c) Circuit diagram
Figure 2.9
A detailed layout example, including vertical process cross section and circuit diagram.
It is left as an exercise for the reader to determine the sizes of both the NMOS and
the PMOS transistors.
2.4
Packaging Integrated Circuits
The IC package plays a fundamental role in the operation and performance of a component. Besides providing a means of bringing signal and supply wires in and out of the silicon die, it also removes the heat generated by the circuit and provides mechanical support.
Finally, its also protects the die against environmental conditions such as humidity.
The packaging technology furthermore has a major impact on the performance and
power-dissipation of a microprocessor or signal processor. This influence is getting more
pronounced as time progresses by the reduction in internal signal delays and on-chip
capacitance as a result of technology scaling. Up to 50% of the delay of a high-performance computer is currently due to packaging delays, and this number is expected to rise.
chapter2.fm Page 57 Friday, January 18, 2002 8:59 AM
Section 2.4
Packaging Integrated Circuits
57
The search for higher-performance packages with fewer inductive or capacitive parasitics
has accelerated in recent years.
The increasing complexity of what can be integrated on a single die also translates into a
need for ever more input-output pins, as the number of connections going off-chip tends to
be roughly proportional to the complexity of the circuitry on the chip. This relationship
was first observed by E. Rent of IBM (published in [Landman71]), who translated it into
an empirical formula that is appropriately called Rent’s rule. This formula relates the number of input/output pins to the complexity of the circuit, as measured by the number of
gates.
P = K × Gβ
(2.1)
where K is the average number of I/Os per gate, G the number of gates, β the Rent exponent, and P the number of I/O pins to the chip. β varies between 0.1 and 0.7. Its value
depends strongly upon the application area, architecture, and organization of the circuit, as
demonstrated in Table 2.1. Clearly, microprocessors display a very different input/output
behavior compared to memories.
Table 2.1
Rent’s constant for various classes of systems ([Bakoglu90])
Application
β
K
Static memory
0.12
6
Microprocessor
0.45
0.82
Gate array
0.5
1.9
High-speed computer (chip)
0.63
1.4
High-speed computer (board)
0.25
82
The observed rate of pin-count increase for integrated circuits varies between 8% to
11% per year, and it has been projected that packages with more than 2000 pins will be
required by the year 2010. For all these reasons, traditional dual-in-line, through-hole
mounted packages have been replaced by other approaches such as surface-mount, ballgrid array, and multichip module techniques. It is useful for the circuit designer to be
aware of the available options, and their pros and cons.
Due to its multi-functionality, a good package must comply with a large variety of
requirements.
• Electrical requirements—Pins should exhibit low capacitance (both interwire and
to the substrate), resistance, and inductance. A large characteristic impedance
should be tuned to optimize transmission line behavior. Observe that intrinsic integrated-circuit impedances are high.
• Mechanical and thermal properties—The heat-removal rate should be as high as
possible. Mechanical reliability requires a good matching between the thermal properties of the die and the chip carrier. Long-term reliability requires a strong connection from die to package as well as from package to board.
chapter2.fm Page 58 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
58
Chapter 2
• Low Cost—Cost is always one of the more important properties. While ceramics
have a superior performance over plastic packages, they are also substantially more
expensive. Increasing the heat removal capacity of a package also tends to raise the
package cost. The least expensive plastic packaging can dissipate up to 1 W. Somewhat more expensive, but still cheap, plastic packages can dissipate up to 2W.
Higher dissipation requires more expensive ceramic packaging. Chips dissipating
over 50 W require special heat sink attachments. Even more extreme techniques
such as fans and blowers, liquid cooling hardware, or heat pipes, are needed for
higher dissipation levels.
Packing density is a major factor in reducing board cost. The increasing pin count
either requires an increase in the package size or a reduction in the pitch between the
pins. Both have a profound effect on the packaging economics.
Packages can be classified in many different ways —by their main material, the
number of interconnection levels, and the means used to remove heat. In this short section,
we can only glance briefly at each of those issues.
2.4.1
Package Materials
The most common materials used for the package body are ceramic and polymers (plastics). The latter have the advantage of being substantially cheaper, but suffer from inferior
thermal properties. For instance, the ceramic Al2O3 (Alumina) conducts heat better than
SiO2 and the Polyimide plastic, by factors of 30 and 100 respectively. Furthermore, its
thermal expansion coefficient is substantially closer to the typical interconnect metals.
The disadvantage of alumina and other ceramics is their high dielectric constant, which
results in large interconnect capacitances.
2.4.2
Interconnect Levels
The traditional packaging approach uses a two-level interconnection strategy. The die is
first attached to an individual chip carrier or substrate. The package body contains an
internal cavity where the chip is mounted. These cavities provide ample room for many
connections to the chip leads (or pins). The leads compose the second interconnect level
and connect the chip to the global interconnect medium, which is normally a PC board.
Complex systems contain even more interconnect levels, since boards are connected
together using backplanes or ribbon cables. The first two layers of the interconnect hierarchy are illustrated in the drawing of Figure 2.10. The following sections provide a brief
overview of the interconnect techniques used at levels one and two of the interconnect
hierarchy, followed by a short discussion of some more advanced packaging approaches.
Interconnect Level 1 —Die-to-Package-Substrate
For a long time, wire bonding was the technique of choice to provide an electrical connection between die and package. In this approach, the backside of the die is attached to the
substrate using glue with a good thermal conductance. Next, the chip pads are individually
connected to the lead frame with aluminum or gold wires. The wire-bonding machine use
chapter2.fm Page 59 Friday, January 18, 2002 8:59 AM
Section 2.4
Packaging Integrated Circuits
59
Figure 2.10 Interconnect hierarchy in traditional IC
packaging.
for this purpose operates much like a sewing machine. An example of wire bonding is
shown in Figure 2.11. Although the wire-bonding process is automated to a large degree,
it has some major disadvantages.
Substrate
Bonding wire
Die
Pad
Lead frame
Figure 2.11
Wire bonding.
1. Wires must be attached serially, one after the other. This leads to longer manufacturing times with increasing pin counts.
2. Larger pin counts make it substantially more challenging to find bonding patterns
that avoid shorts between the wires.
Bonding wires have inferior electrical properties, such as a high individual inductance (5
nH or more) and mutual inductance with neighboring signals. The inductance of a bonding
wire is typically about 1 nH/mm, while the inductance per package pin ranges between 7
and 40 nH per pin depending on the type of package as well as the positioning of the pin
on the package boundary [Steidel83].Typical values of the parasitic inductances and
capacitances for a number of commonly used packages are summarized in Table 2.2.
3. The exact value of the parasitics is hard to predict because of the manufacturing
approach and irregular outlay.
New attachment techniques are being explored as a result of these deficiencies. In
one approach, called Tape Automated Bonding (or TAB), the die is attached to a metal
lead frame that is printed on a polymer film (typically polyimide) (Figure 2.12a). The connection between chip pads and polymer film wires is made using solder bumps (Figure
2.12b). The tape can then be connected to the package body using a number of techniques.
One possible approach is to use pressure connectors.
chapter2.fm Page 60 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
60
Sprocket
hole
Film + Pattern
Chapter 2
Solder bump
Die
Test
pads
Substrate
Lead
frame
(b) Die attachment using solder bumps
Polymer film
(a) Polymer tape with imprinted wiring pattern
Figure 2.12
Tape-automated bonding (TAB).
Table 2.2 Typical capacitance and inductance values of package and bonding styles (from [Steidel83]
and [Franzon93]).
Package Type
Capacitance
(pF)
Inductance
(nH)
68-pin plastic DIP
4
35
68-pin ceramic DIP
7
20
256-pin grid array
1–5
2–15
Wire bond
0.5–1
1–2
Solder bump
0.1–0.5
0.01–0.1
The advantage of the TAB process is that it is highly automated. The sprockets in
the film are used for automatic transport. All connections are made simultaneously. The
printed approach helps to reduce the wiring pitch, which results in higher lead counts.
Elimination of the long bonding wires improves the electrical performance. For instance,
for a two-conductor layer, 48 mm TAB Circuit, the following electrical parameters hold: L
≈ 0.3–0.5 nH, C ≈ 0.2–0.3 pF, and R ≈ 50–200 Ω [Doane93, p. 420].
Another approach is to flip the die upside-down and attach it directly to the substrate
using solder bumps. This technique, called flip-chip mounting, has the advantage of a
superior electrical performance (Figure 2.13). Instead of making all the I/O connections
on the die boundary, pads can be placed at any position on the chip. This can help address
the power- and clock-distribution problems, since the interconnect materials on the substrate (e.g., Cu or Au) are typically of a better quality than the Al on the chip.
Interconnect Level 2—Package Substrate to Board
When connecting the package to the PC board, through-hole mounting has been the packaging style of choice. A PC board is manufactured by stacking layers of copper and insu-
chapter2.fm Page 61 Friday, January 18, 2002 8:59 AM
Section 2.4
Packaging Integrated Circuits
61
Die
Solder bumps
Interconnect
layers
Figure 2.13
Substrate
Flip-chip bonding.
lating epoxy glass. In the through-hole mounting approach, holes are drilled through the
board and plated with copper. The package pins are inserted and electrical connection is
made with solder (Figure 2.14a). The favored package in this class was the dual-in-line
package or DIP (Figure 2.15a). The packaging density of the DIP degrades rapidly when
the number of pins exceeds 64. This problem can be alleviated by using the pin-grid-array
(PGA) package that has leads on the entire bottom surface instead of only on the periphery
(Figure 2.15b). PGAs can extend to large pin counts (over 400 pins are possible).
(a) Through-hole mounting
(b) Surface mount
Figure 2.14
Board-mounting approaches.
The through-hole mounting approach offers a mechanically reliable and sturdy connection. However, this comes at the expense of packaging density. For mechanical reasons, a minimum pitch of 2.54 mm between the through-holes is required. Even under
those circumstances, PGAs with large numbers of pins tend to substantially weaken the
board. In addition, through-holes limit the board packing density by blocking lines that
might otherwise have been routed below them, which results in longer interconnections.
PGAs with large pin counts hence require extra routing layers to connect to the multitudes
of pins. Finally, while the parasitic capacitance and inductance of the PGA are slightly
lower than that of the DIP, their values are still substantial.
Many of the shortcomings of the through-hole mounting are solved by using the
surface-mount technique. A chip is attached to the surface of the board with a solder connection without requiring any through-holes (Figure 2.14b). Packing density is increased
for the following reasons: (1) through-holes are eliminated, which provides more wiring
space; (2) the lead pitch is reduced; and (3) chips can be mounted on both sides of the
board. In addition, the elimination of the through-holes improves the mechanical strength
of the board. On the negative side, the on-the-surface connection makes the chip-board
connection weaker. Not only is it cumbersome to mount a component on a board, but also
more expensive equipment is needed, since a simple soldering iron will not do anymore.
Finally, testing of the board is more complex, because the package pins are no longer
accessible at the backside of the board. Signal probing becomes hard or even impossible.
A variety of surface-mount packages are currently in use with different pitch and
pin-count parameters. Three of these packages are shown in Figure 2.15: the small-outline
package with gull wings, the plastic leaded package (PLCC) with J-shaped leads, and the
chapter2.fm Page 62 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
62
Chapter 2
2
7
5
1
3
Bare die
DIP
PGA
Small-outline IC
Quad flat pack
PLCC
Leadless carrier
4
6
Figure 2.15
1
2
3
4
5
6
7
An overview of commonly used package types.
leadless chip carrier. An overview of the most important parameters for a number of
packages is given in Table 2.3.
Table 2.3
Parameters of various types of chip carriers.
Package type
Lead spacing
(Typical)
Lead count
(Maximum)
Dual-in-line
2.54 mm
64
Pin grid array
2.54 mm
> 300
Small-outline IC
1.27 mm
28
Leaded chip carrier (PLCC)
1.27 mm
124
Leadless chip carrier
0.75 mm
124
Even surface-mount packaging is unable to satisfy the quest for evermore higher
pin-counts. This is worsened by the demand for power connections: today’s high performance chips, operating at low supply voltages, require as many power and ground pins as
signal I/Os! When more than 300 I/O connections are needed, solder balls replace pins as
the preferred interconnect medium between package and board. An example of such a
packaging approach, called ceramic ball grid array (BGA), is shown in Figure 2.16. Solder bumps are used to connect both the die to the package substrate, and the package to the
board. The area array interconnect of the BGA provides constant input/output density
regardless of the number of total package I/O pins. A minimum pitch between solder balls
of as low as 0.8 mm can be obtained, and packages with multiple 1000’s of I/O signals are
feasible.
chapter2.fm Page 63 Friday, January 18, 2002 8:59 AM
Section 2.4
Packaging Integrated Circuits
Lid
Thermal
grease
Chip
63
Flip-chip
solder joints
Ceramic base
Board
(a)
Solder ball
(b)
Figure 2.16 Ball grid array packaging; (a) cross-section, (b) photo of package bottom
Multi-Chip Modules—Die-to-Board
The deep hierarchy of interconnect levels in the package is becoming unacceptable in
today’s complex designs with their higher levels of integration, large signal counts, and
increased performance requirements. The trend is toward reducing the number of levels.
For the time being, attention is focused on the elimination of the first level in the packaging hierarchy. Eliminating one layer in the packaging hierarchy by mounting the die
directly on the wiring backplanes—board or substrate—offers a substantial benefit when
performance or density is a major issue. This packaging approach is called the multichip
module technique (or MCM), and results in a substantial increase in packing density as
well as improved performance.
A number of the previously mentioned die-mounting techniques can be adapted to
mount dies directly on the substrate. This includes wire bonding, TAB, and flip-chip,
although the latter two are preferable. The substrate itself can vary over a wide range of
materials, depending upon the required mechanical, electrical, thermal, and economical
requirements. Materials of choice are epoxy substrates (similar to PC boards), metal,
ceramics, and silicon. Silicon has the advantage of presenting a perfect match in mechanical and thermal properties with respect to the die material.
The main advantages of the MCM approach are the increased packaging density and
performance. An example of an MCM module implemented using a silicon substrate
(commonly dubbed silicon-on-silicon) is shown in Figure 2.17. The module, which implements an avionics processor module and is fabricated by Rockwell International, contains
53 ICs and 40 discrete devices on a 2.2″ × 2.2″ substrate with aluminum polyimide interconnect. The interconnect wires are only an order of magnitude wider than what is typical
for on-chip wires, since similar patterning approaches are used. The module itself has 180
I/O pins. Performance is improved by the elimination of the chip-carrier layer with its
assorted parasitics, and through a reduction of the global wiring lengths on the die, a result
of the increased packaging density. For instance, a solder bump has an assorted capacitance and inductance of only 0.1 pF and 0.01 nH respectively. The MCM technology can
also reduce power consumption significantly, since large output drivers—and associated
dissipation—become superfluous due to the reduced load capacitance of the output pads.
chapter2.fm Page 64 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
64
Figure 2.17
Chapter 2
Avionics processor module. Courtesy of Rockwell International.
The dynamic power associated with the switching of the large load capacitances is simultaneously reduced.
While MCM technology offers some clear benefits, its main disadvantage is economic. This technology requires some advanced manufacturing steps that make the process expensive. The approach is only justifiable when either dense housing or extreme
performance is essential. In the near future, this argument might become obsolete as
MCM approaches proliferate.
2.4.3
Thermal Considerations in Packaging
As the power consumption of integrated circuits rises, it becomes increasingly important
to efficiently remove the heat generated by the chips. A large number of failure mechanisms in ICs are accentuated by increased temperatures. Examples are leakage in reversebiased diodes, electromigration, and hot-electron trapping. To prevent failure, the temperature of the die must be kept within certain ranges. The supported temperature range for
commercial devices during operation equals 0° to 70°C. Military parts are more demanding and require a temperature range varying from –55° to 125°C.
The cooling effectiveness of a package depends upon the thermal conduction of the
package material, which consists of the package substrate and body, the package composition, and the effectiveness of the heat transfer between package and cooling medium.
Standard packaging approaches use still or circulating air as the cooling medium. The
transfer efficiency can be improved by adding finned metal heat sinks to the package.
More expensive packaging approaches, such as those used in mainframes or supercomput-
chapter2.fm Page 65 Friday, January 18, 2002 8:59 AM
Section 2.5
Perspective — Trends in Process Technology
65
ers, force air, liquids, or inert gases through tiny ducts in the package to achieve even
greater cooling efficiencies.
<We may want to briefly introduce the thermal equation here.>
As an example, a 40-pin DIP has a thermal resistance of 38 °C/W and 25 °C/W for
natural and forced convection of air. This means that a DIP can dissipate 2 watts (3 watts)
of power with natural (forced) air convection, and still keep the temperature difference
between the die and the environment below 75 °C. For comparison, the thermal resistance
of a ceramic PGA ranges from 15 ° to 30 °C/W.
Since packaging approaches with decreased thermal resistance are prohibitively
expensive, keeping the power dissipation of an integrated circuit within bounds is an economic necessity. The increasing integration levels and circuit performance make this task
nontrivial. An interesting relationship in this context has been derived by Nagata
[Nagata92]. It provides a bound on the integration complexity and performance as a function of the thermal parameters
N G ∆T
------- ≤ ------t p θE
(2.2)
where NG is the number of gates on the chip, tp the propagation delay, ∆T the maximum
temperature difference between chip and environment, θ the thermal resistance between
them, and E the switching energy of each gate.
Example 2.2 Thermal Bounds On Integration
For ∆T = 100 °C, θ = 2.5 °C/W and E = 0.1 pJ, this results in NG/tp ≤ 4 × 105 (gates/nsec). In
other words, the maximum number of gates on a chip, when all gates are operating simultaneously, must be less than 400,000 if the switching speed of each gate is 1 nsec. This is equivalent to a power dissipation of 40 W.
Fortunately, not all gates are operating simultaneously in real systems. The maximum number of gates can be substantially larger, based on the activity in the circuit. For
instance, it was experimentally derived that the ratio between the average switching period
and the propagation delay ranges from 20 to 200 in mini- and large-scale computers
[Masaki92].
Nevertheless, Eq. (2.2) demonstrates that heat dissipation and thermal concerns
present an important limitation on circuit integration. Design approaches for low power
that reduce either E or the activity factor are rapidly gaining importance.
2.5
Perspective — Trends in Process Technology
Modern CMOS processes pretty much track the flow described in the previous sections
although a number of the steps might be reversed, a single well approach might be followed, a grown field oxide instead of the trench approach might be used, or extra steps
such as LDD (Lightly Doped Drain) might be introduced. Also, it is quite common to
cover the polysilicon interconnections as well as the drain and source regions with a silicide such as TiSi2 to improve the conductivity (see Figure 2.2). This extra operation is
chapter2.fm Page 66 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
66
Chapter 2
inserted between steps i and j of our process. Some important modifications or improvements to the technology are currently under way or are on the horizon, and deserve some
attention. Beyond these, it is our belief that no dramatic changes, breaking away from the
described CMOS technology, must be expected in the next decade.
2.5.1
Short-Term Developments
Copper and Low-k Dielectrics
A recurring theme in this text book will be the increasing impact of interconnect on the
overall design performance. Process engineers are continuously evaluating alternative
options for the traditional ‘Aluminum conductor—SiO2 insulator’ combination that has
been the norm for the last decades. In 1998, engineers at IBM introduced an approach that
finally made the use of Copper as an interconnect material in a CMOS process viable and
economical [IEEESpectrum98]. Copper has the advantage of have a resistivity that is substantially lower than Aluminum. Yet it has the disadvantage of easy diffusion into silicon,
which degrades the characteristics of the devices. Coating the copper with a buffer material such as Titanium Nitride, preventing the diffusion, addresses this problem, but
requires a special deposition process. The Dual Damascene process, introduced by IBM,
(Figure 2.18) uses a metallization approach that fills trenches etched into the insulator, followed by a chemical-mechanical polishing step. This is in contrast with the traditional
approach that first deposits a full metal layer, and removes the redundant material through
etching.
In addition to the lower resistivity interconnections, insulator materials with a lower
dielectric constant than SiO2 —and hence lower capacitance— have also found their way
into the production process starting with the 0.18 µm CMOS process generation.
(a)
(b)
Figure 2.18
The damascene process (from Geppert98]):
process steps (a), and microphotograph of interconnect after
removal of insulator (b)
chapter2.fm Page 67 Friday, January 18, 2002 8:59 AM
Section 2.5
Perspective — Trends in Process Technology
67
Silicon-on-Insulator
While having been around for quite a long time, there seems to be a good chance that Silicon-on-Insulator (SOI) CMOS might replace the traditional CMOS process, described in
the previous sections (also known as the bulk CMOS process). The main difference lies in
the start material: the transistors are constructed in a very thin layer of silicon, deposited
on top of a thick layer of insulating SiO2 (Figure 2.19). The primary advantages of the SOI
process are reduced parasitics and better transistor on-off characteristics. It has, for
instance, been demonstrated by researchers at IBM that the porting of a design from a bulk
CMOS to an SOI process —leaving all other design and process parameters such as channel length and oxide thickness identical— yields a performance improvement of 22%
[Allen99]. Preparing a high quality SOI substrate at an economical cost was long the main
hindrance against a large-scale introduction of the process. This picture has changed at the
end of the nineties, and SOI is steadily moving into the mainstream.
Gate
tox
oxide
n+
tSi
p
Buried Oxide (BOX)
n+
oxide
tBox
p-substrate
(a)
(b)
Figure 2.19 Silicon-on-insulator process— schematic diagram (a) and SEM cross-section (b).
2.5.2
In the Longer Term
Extending the life of CMOS technology beyond the next decade, and deeply below the
100 nm channel length region however will require re-engineering of both the process
technology and the device structure. We already are witnessing the emergence of a wide
range of new devices (such as organic transistors, molecular switches, and quantum
devices). While projecting what approaches will dominate in that era equals resorting to
crystal-ball gazing, one interesting development is worth mentioning.
Truly Three-Dimensional Integrated Circuits
Getting signals in and out of the computation elements in a timely fashion is one of the
main challenges presented by the continued increase in integration density. One way to
address this problem is to introduce extra active layers, and to sandwich them in-between
the metal interconnect layers (Figure 2.20). This enables us to position high density memory on top of the logic processors implemented in the bulk CMOS, reducing the distance
between computation and storage, and hence also the delay [Souri00]. In addition, devices
with different voltage, performance, or substrate material requirements can be placed in
chapter2.fm Page 68 Friday, January 18, 2002 8:59 AM
THE MANUFACTURING PROCESS
68
Chapter 2
different layers. For instance, the top active layer can be reserved for the realization of
optical transceivers, which may help to address the input/output requirements, or MEMS
(Micro Electro-Mechanical Systems) devices providing sensoring functions or radio-frequency (RF) interfaces.
optical device
T3 - Optical I/O; MEMS
M6
M5
M4
M3
n+/p+
n+/p+
T2 - High Density Memory
M2
M1
n+/p+
n+/p+
Bulk
T1 - Logic
Figure 2.20 Example of true 3D integration. Extra
active layers (T*), implementing high density memory
and I/O, are sandwiched between the metal
interconnect layers (M*).
While this approach may seem to be promising, a number of major challenges and
hindrances have to be resolved to make it really viable. How to remove the dissipated heat
is one of the compelling questions. Ensuring yield is another one. Yet, researchers are
demonstrating major progress, and 3D integration might very well be on the horizon.
Before the true solution arrives, we might have to rely on some intermediate approaches.
One alternative, called 2.5D integration, is to bond two fully processed wafers, on which
circuits are fabricated on the surface such that the chips completely overlap. Vias are
etched to electrically connect both chips after metallization. The advantages of this technology lie in the similar electrical properties of devices on all active levels and the independence of processing temperature since all chips can be fabricated separately and later
bonded. The major limitation of this technique is its lack of precision (best case alignment
+/- 2 µm), which restricts the inter-chip communication to global metal lines.
One picture that strongly emerges from these futuristic devices is that the line
between chip, substrate, package, and board is blurring, and that designers of these systems-on-a-die will have to consider all these aspects simultaneously.
2.6
Summary
This chapter has presented an a birds-eye view on issues regarding the manufacturing and
packaging of CMOS integrated circuits.
• The manufacturing process of integrated circuits require a large number of steps,
each of which consists of a sequence of basic operations. A number of these steps
and/or operations, such as photolithograpical exposure and development, material
deposition, and etching, are executed very repetitively in the course of the manufacturing process.
chapter2.fm Page 69 Friday, January 18, 2002 8:59 AM
Section 2.7
To Probe Further
69
• The optical masks forms the central interface between the intrinsics of the manufacturing process and the design that the user wants to see transferred to the silicon fabric.
• The design rules set define the constraints n terms of minimum width and separation
that the IC design has to adhere to if the resulting circuit is to be fully functional.
This design rules acts as the contract between the circuit designer and the process
engineer.
• The package forms the interface between the circuit implemented on the silicon die
and the outside world, and as such has a major impact on the performance, reliability, longevity, and cost of the integrated circuit.
2.7
To Probe Further
Many textbooks on semiconductor manufacturing have been published over the last few
decades. An excellent overview of the state-of-the-art in CMOS manufacturing can be
found in the “Silicon VLSI Technology” book by J. Plummer, M. Deal, and P. Griffin
[Plummer00]. A visual overview of the different steps in the manufacturing process can be
found on the web at [Fullman99]. Other sources for information are the IEEE Transactions
on Electron Devices, and the Technical Digest of the IEDM conference.
REFERENCES
[Allen99] D. Allen, et al., “A 0.2 µm 1.8 V SOI 550 MHz PowerPC Microprocessor with Copper
Interconnects,” Proceedings IEEE ISSCC Conference, vol. XLII, pp. 438-439, February 1999.
[Bakoglu90] H. Bakoglu, Circuits, Interconnections and Packaging for VLSI, Addison-Wesley,
1990.
[Doane93] D. Doane, ed., Multichip Module Technologies and Alternatives, Van Nostrand-Reinhold, 1993.
[Franzon93] P. Franzon, “Electrical Design of Digital Multichip Modules,” in [Doane93], pp
525–568, 1993.
[Fullman99] Fullman Kinetics, “The Semiconductor Manufacturing Process”, http://www.fullmankinetics.com/semiconductors/semiconductors.html, 1999.
[Geppert98] L. Geppert, “Technology—1998 Analysis and Forecast”, IEEE Spectrum, Vol. 35, No
1, pp. 23, January 1998.
[Landman71] B. Landman and R. Russo, “On a Pin versus Block Relationship for Partitions of
Logic Graphs,” IEEE Trans. on Computers, vol. C-20, pp. 1469–1479, December 1971.
[Masaki92] A. Masaki, “Deep-Submicron CMOS Warms Up to High-Speed Logic,” Circuits and
Devices Magazine, Nov. 1992.
[Mead80] C. Mead and L. Conway, Introduction to VLSI Systems, Addison-Wesley, 1980.
[Nagata92] M. Nagata, “Limitations, Innovations, and Challenges of Circuits and Devices into a
Half Micrometer and Beyond,” IEEE Journal of Solid State Circuits, vol. 27, no. 4, pp. 465–472,
April 1992.
chapter2.fm Page 70 Friday, January 18, 2002 8:59 AM
70
THE MANUFACTURING PROCESS
Chapter 2
[Plummer00] J. Plummer, M. Deal, and P. Griffin, Silicon VLSI Technology, Prentice Hall, 2000.
[Steidel83] C. Steidel, “Assembly Techniques and Packaging,” in [Sze83], pp. 551–598, 1983.
[Souri00] S. J. Souri, K. Banerjee, A. Mehrotra and K. C. Saraswat, “Multiple Si Layer ICs: Motivation, Performance Analysis, and Design Implications,” Proceedings 37th Design Automation
Conference, pp. 213-220, June 2000.
chapter3.fm Page 77 Friday, January 18, 2002 9:00 AM
CHAPTER
3
THE DEVICES
Qualitative understanding of MOS devices
n
Simple component models for manual analysis
n
Detailed component models for SPICE
n
Impact of process variations
3.1
Introduction
3.3.3
Dynamic Behavior
3.2
The Diode
3.3.4
The Actual MOS Transistor—Some
Secondary Effects
3.3.5
SPICE Models for the MOS Transistor
3.3
3.2.1
A First Glance at the Diode — The
Depletion Region
3.2.2
Static Behavior
3.4
A Word on Process Variations
3.2.3
Dynamic, or Transient, Behavior
3.5
Perspective: Technology Scaling
3.2.4
The Actual Diode—Secondary Effects
3.2.5
The SPICE Diode Model
The MOS(FET) Transistor
3.3.1
A First Glance at the Device
3.3.2
The MOS Transistor under Static
Conditions
77
chapter3.fm Page 78 Friday, January 18, 2002 9:00 AM
THE DEVICES
78
3.1
Chapter 3
Introduction
It is a well-known premise in engineering that the conception of a complex construction
without a prior understanding of the underlying building blocks is a sure road to failure.
This surely holds for digital circuit design as well. The basic building blocks in today’s
digital circuits are the silicon semiconductor devices, more specifically the MOS transistors and to a lesser degree the parasitic diodes, and the interconnect wires. The role of the
semiconductor devices has been appreciated for a long time in the world of digital integrated circuits. On the other hand, interconnect wires have only recently started to play a
dominant role as a result of the advanced scaling of the semiconductor technology.
Giving the reader the necessary knowledge and understanding of these components
is the prime motivation for the next two chapters. It is not our intention to present an indepth treatment of the physics of semiconductor devices and interconnect wires. We refer
the reader to the many excellent textbooks on semiconductor devices for that purpose,
some of which are referenced in the To Probe Further section at the end of the chapters.
The goal is rather to describe the functional operation of the devices, to highlight the properties and parameters that are particularly important in the design of digital gates, and to
introduce notational conventions.
Another important function of this chapter is the introduction of models. Taking all
the physical aspects of each component into account when designing complex digital circuits leads to an unnecessary complexity that quickly becomes intractable. Such an
approach is similar to considering the molecular structure of concrete when constructing a
bridge. To deal with this issue, an abstraction of the component behavior called a model is
typically employed. A range of models can be conceived for each component presenting a
trade-off between accuracy and complexity. A simple first-order model is useful for manual analysis. It has limited accuracy but helps us to understand the operation of the circuit
and its dominant parameters. When more accurate results are needed, complex, second- or
higher-order models are employed in conjunction with computer-aided simulation. In this
chapter, we present both first-order models for manual analysis as well as higher-order
models for simulation for each component of interest.
Designers tend to take the component parameters offered in the models for granted.
They should be aware, however, that these are only nominal values, and that the actual
parameter values vary with operating temperature, over manufacturing runs, or even over
a single wafer. To highlight this issue, a short discussion on process variations and their
impact is included in the chapter.
3.2
The Diode
Although diodes rarely occur directly in the schematic diagrams of present-day digital
gates, they are still omnipresent. Each MOS transistor implicitly contains a number of
reverse-biased diodes that directly influence the behavior of the device. Especially, the
voltage-dependent capacitances contributed by these parasitic elements play an important
role in the switching behavior of the MOS digital gate. Diodes are also used to protect the
input devices of an IC against static charges. Therefore, a brief review of the basic properties and device equations of the diode is appropriate. Rather than being comprehensive,
chapter3.fm Page 79 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
79
we choose to focus on those aspects that prove to be influential in the design of digital
MOS circuits, this is the operation in reverse-biased mode.1
3.2.1
A First Glance at the Diode — The Depletion Region
The pn-junction diode is the simplest of the semiconductor devices. Figure 3.1a shows a
cross-section of a typical pn-junction. It consists of two homogeneous regions of p- and ntype material, separated by a region of transition from one type of doping to another,
which is assumed thin. Such a device is called a step or abrupt junction. The p-type material is doped with acceptor impurities (such as boron), which results in the presence of
holes as the dominant or majority carriers. Similarly, the doping of silicon with donor
impurities (such as phosphorus or arsenic) creates an n-type material, where electrons are
the majority carriers. Aluminum contacts provide access to the p- and n-terminals of the
device. The circuit symbol of the diode, as used in schematic diagrams, is introduced in
Figure 3.1c.
To understand the behavior of the pn-junction diode, we often resort to a one-dimensional simplification of the device (Figure 3.1b). Bringing the p- and n-type materials
together causes a large concentration gradient at the boundary. The electron concentration
changes from a high value in the n-type material to a very small value in the p-type
material. The reverse is true for the hole concentration. This gradient causes electrons to
B
A
Al
SiO2
p
n
(a) Cross-section of pn-junction in an IC process
A
Al
A
p
n
B
B
(b) One-dimensional
representation
1
(c) Diode symbol
Figure 3.1 Abrupt pn-junction diode
and its schematic symbol.
We refer the interested reader to the web-site of the textbook for a comprehensive description of the
diode operation.
chapter3.fm Page 80 Friday, January 18, 2002 9:00 AM
THE DEVICES
80
Chapter 3
diffuse from n to p and holes to diffuse from p to n. When the holes leave the p-type material, they leave behind immobile acceptor ions, which are negatively charged. Consequently, the p-type material is negatively charged in the vicinity of the pn-boundary.
Similarly, a positive charge builds up on the n-side of the boundary as the diffusing electrons leave behind the positively charged donor ions. The region at the junction, where the
majority carriers have been removed, leaving the fixed acceptor and donor ions, is called
the depletion or space-charge region. The charges create an electric field across the
boundary, directed from the n to the p-region. This field counteracts the diffusion of holes
and electrons, as it causes electrons to drift from p to n and holes to drift from n to p.
Under equilibrium, the depletion charge sets up an electric field such that the drift currents
are equal and opposite to the diffusion currents, resulting in a zero net flow.
The above analysis is summarized in Figure 3.2 that plots the current directions, the
charge density, the electrical field, and the electrostatic field of the abrupt pn-junction
under zero-bias conditions. In the device shown, the p material is more heavily doped than
Hole diffusion
Electron diffusion
(a) Current flow
p
n
Hole drift
Electron drift
ρ
Charge
density
+
x
-
Electrical
field
E
x
(c) Electric field
V
Potential
x
-W1
Figure 3.2
(b) Charge density
Distance
W2
The abrupt pn-junction under equilibrium bias.
φ0
(d) Electrostatic
potential
chapter3.fm Page 81 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
81
the n, or NA > ND, with NA and ND the acceptor and donor concentrations, respectively.
Hence, the charge concentration in the depletion region is higher on the p-side of the junction. Figure 3.2 also shows that under zero bias, there exists a voltage φ0 across the junction, called the built-in potential. This potential has the value
NAND
φ 0 = φ T ln ------------n i2
(3.1)
kT
φ T = ------ = 26mV at 300 K
q
(3.2)
where φT is the thermal voltage
The quantity ni is the intrinsic carrier concentration in a pure sample of the semiconductor
and equals approximately 1.5 × 1010 cm-3 at 300 K for silicon.
Example 3.1 Built-in Voltage of pn-junction
An abrupt junction has doping densities of NA = 1015 atoms/cm3, and ND = 1016 atoms/cm3.
Calculate the built-in potential at 300 K.
From Eq. (3.1),
10 15 × 10 16
- mV = 638 mV
φ 0 = 26 ln -------------------------2.25 × 10 20
3.2.2
Static Behavior
The Ideal Diode Equation
Assume now that a forward voltage VD is applied to the junction or, in other words, that
the potential of the p-region is raised with respect to the n-zone. The applied potential lowers the potential barrier. Consequently, the flow of mobile carriers across the junction
increases as the diffusion current dominates the drift component. These carriers traverse
Excess carriers
pn0
Excess carriers
np0
–Wp
p-region
–W1 0
W2
n-region
Wn
Metal contact to n-region
Depletion region
Metal contact to p-region
Minority carrier concentration
x
Figure 3.3 Minority carrier concentrations in the neutral region near an abrupt pn-junction under forward-bias
conditions.
chapter3.fm Page 82 Friday, January 18, 2002 9:00 AM
THE DEVICES
82
Chapter 3
the depletion region and are injected into the neutral n- and p-regions, where they become
minority carriers, as is illustrated in Figure 3.3. Under the assumption that no voltage gradient exists over the neutral regions, which is approximately the case for most modern
devices, these minority carriers will diffuse through the region as a result of the concentration gradient until they get recombined with a majority carrier. The net result is a current
flowing through the diode from the p-region to the n-region, and the diode is said to be in
the forward-bias mode.
On the other hand, when a reverse voltage VD is applied to the junction or when the
potential of the p-region is lowered with respect to the n-region, the potential barrier is
raised. This results in a reduction in the diffusion current, and the drift current becomes
dominant. A current flows from the n-region to the p-region. Since the number of minority
carriers in the neutral regions (electrons in the p-zone, holes in the n-region) is very small,
this drift current component is virtually ignorable (Figure 3.4). It is fair to state that in the
reverse-bias mode the diode operates as a nonconducting, or blocking, device. The diode
thus acts as a one-way conductor.
Metal contact to n-region
np0
pn0
pn(x)
np(x)
–Wp
Figure 3.4
conditions.
Depletion region
Metal contact to p-region
Minority carrier concentration
p-region
–W1 0
W2
n-region
Wn
x
Minority carrier concentration in the neutral regions near the pn-junction under reverse-bias
The most important property of the diode current is its exponential dependence upon
the applied bias voltage. This is illustrated in Figure 3.5, which plots the diode current ID
as a function of the bias voltage VD. The exponential behavior for positive-bias voltages is
even more apparent in Figure 3.5b, where the current is plotted on a logarithmic scale. The
current increases by a factor of 10 for every extra 60 mV (= 2.3 φT) of forward bias. At
small voltage levels (VD < 0.15 V), a deviation from the exponential dependence can be
observed, which is due to the recombination of holes and electrons in the depletion region.
The behavior of the diode for both forward- and reverse bias conditions is best
described by the well-known ideal diode equation, which relates the current through the
diode ID to the diode bias voltage VD
I D = I S ( e V D ⁄ φT – 1 )
(3.3)
Observe how Eq. (3.3) corresponds to the exponential behavior plotted in Figure 3.5. φT is
the thermal voltage of Eq. (3.2) and is equal to 26 mV at room temperature.
IS represents a constant value, called the saturation current of the diode. It is proportional to the area of the diode, and a function of the doping levels and widths of the neutral
chapter3.fm Page 83 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
83
100
1.5
10–5
Deviation due to
recombination
ID (A)
ID (mA)
2.5
0.5
2.3 φT V / decade
current
10–10
–0.5
–1.0
–0.5
0.0
VD (V)
(a) On a linear scale
Figure 3.5
0.5
1.0
10–15
0.0
0.2
0.4
VD (V)
0.6
0.8
(b) On a logarithmic scale (forward bias only)
Diode current as a function of the bias voltage VD.
regions. Most often, IS is determined empirically.It is worth mentioning that in actual
devices, the reverse currents are substantially larger than the saturation current IS. This is
due to the thermal generation of hole and electron pairs in the depletion region. The electric field present sweeps these carriers out of the region, causing an additional current
component. For typical silicon junctions, the saturation current is nominally in the range
of 10−17 A/µm2, while the actual reverse currents are approximately three orders of magnitude higher. Actual device measurements are, therefore, necessary to determine realistic
values for the reverse diode leakage currents.
Models for Manual Analysis
The derived current-voltage equations can be summarized in a set of simple models that
are useful in the manual analysis of diode circuits. A first model, shown in Figure 3.6a, is
based on the ideal diode equation Eq. (3.3). While this model yields accurate results, it has
the disadvantage of being strongly nonlinear. This prohibits a fast, first-order analysis of
the dc-operation conditions of a network. An often-used, simplified model is derived by
inspecting the diode current plot of Figure 3.5. For a “fully conducting” diode, the voltage
drop over the diode VD lies in a narrow range, approximately between 0.6 and 0.8 V. To a
+
ID = IS(eVD/φT – 1)
VD
+
VD
–
–
VDon
–
(a) Ideal diode model
Figure 3.6
ID
+
Diode models.
(b) First-order diode model
chapter3.fm Page 84 Friday, January 18, 2002 9:00 AM
THE DEVICES
84
Chapter 3
first degree, it is reasonable to assume that a conducting diode has a fixed voltage drop
VDon over it. Although the value of VDon depends upon IS, a value of 0.7 V is typically
assumed. This gives rise to the model of Figure 3.6b, where a conducting diode is replaced
by a fixed voltage source.
Example 3.2 Analysis of Diode Network
Consider the simple network of Figure 3.7 and assume that VS = 3 V, RS = 10 kΩ and IS = 0.5
× 10–16 A. The diode current and voltage are related by the following network equation
VS − RSID = VD
Inserting the ideal diode equation and (painfully) solving the nonlinear equation using either
numerical or iterative techniques yields the following solution: ID = 0.224 mA, and VD =
0.757 V. The simplified model with VDon = 0.7 V produces similar results (VD = 0.7 V, ID =
0.23 A) with far less effort. It hence makes considerable sense to use this model when determining a first-order solution of a diode network.
RS
ID
VS
+
VD
–
Figure 3.7 A simple diode circuit.
3.2.3
Dynamic, or Transient, Behavior
So far, we have mostly been concerned with the static, or steady-state, characteristics of
the diode. Just as important in the design of digital circuits is the response of the device to
changes in its bias conditions. The transient, or dynamic, response determines the maximum speed at which the device can be operated. Because the operation mode of the diode
is a function of the amount of charge present in both the neutral and the space-charge
regions, its dynamic behavior is strongly determined by how fast charge can be moved
around.
While we could embark at this point onto an in-depth analysis of the switching
behavior of the diode in the forward-biasing mode, it is our conviction that this would be
besides the point and unnecessarily complicate the discussion. In fact, all diodes in an
operational MOS digital integrated circuit are reverse-biased and are supposed to remain
so under all circumstances. Only under exceptional conditions may forward-biasing occur.
A signal over(under) shooting the supply rail is an example of such. Due to its detrimental
impact on the overall circuit operation, this should be avoided under all circumstances.
Hence, we will devote our attention solely to what governs the dynamic response of
the diode under reverse-biasing conditions, the depletion-region charge.
chapter3.fm Page 85 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
85
Depletion-Region Capacitance
In the ideal model, the depletion region is void of mobile carriers, and its charge is determined by the immobile donor and acceptor ions. The corresponding charge distribution
under zero-bias conditions was plotted in Figure 3.2. This picture can be easily extended
to incorporate the effects of biasing. At an intuitive level the following observations can
be easily verified—under forward-bias conditions, the potential barrier is reduced, which
means that less space charge is needed to produce the potential difference. This corresponds to a reduced depletion-region width. On the other hand, under reverse conditions,
the potential barrier is increased corresponding to an increased space charge and a wider
depletion region. These observations are confirmed by the well- known depletion-region
expressions given below (a derivation of these expressions, which are valid for abrupt
junctions, is either simple or can be found in any textbook on devices such as [Howe97]).
One observation is crucial — due to the global charge neutrality requirement of the diode,
the total acceptor and donor charges must be numerically equal.
1. Depletion-region charge (VD is positive for forward bias).
N A ND
Q j = A D 2ε si q ------------------- ( φ – VD )
N A + N D 0
(3.4)
2. Depletion-region width.
W j = W 2 – W1 =
N A + N D
2ε
- ( φ – VD )
--------si- ------------------ q N A ND 0
(3.5)
3. Maximum electric field.
Ej =
NAND
2q
- ( φ – VD )
------ ------------------ ε si N A + N D 0
(3.6)
In the preceding equations εsi stands for the electrical permittivity of silicon and equals 11.7
times the permittivity of a vacuum, or 1.053 × 10−10 F/m. The ratio of the n- versus p-side
of the depletion-region width is determined by the doping-level ratios: W2/(−W1) = NA/ND.
From an abstract point of view, it is possible to visualize the depletion region as a
capacitance, albeit one with very special characteristics. Because the space-charge region
contains few mobile carriers, it acts as an insulator with a dielectric constant εsi of the
semiconductor material. The n- and p-regions act as the capacitor plates. A small change
in the voltage applied to the junction dVD causes a change in the space charge dQj. Hence,
a depletion-layer capacitance can be defined
Cj =
ε si q N A N D
dQ j
= A D -------- -------------------- ( φ – V D ) –1
2 N A + N D 0
d VD
C j0
= ---------------------------1 – VD ⁄ φ0
(3.7)
where Cj0 is the capacitance under zero-bias conditions and is only a function of the physical parameters of the device.
chapter3.fm Page 86 Friday, January 18, 2002 9:00 AM
THE DEVICES
86
Chapter 3
2.0
Abrupt junction
Cj (fF)
1.5
m = 0.5
1.0
Linear junction
m = 0.33
0.5
0.0
-4.0
Cj0
-2.0
0.0
VD (V)
Figure 3.8
Junction capacitance (in fF/µm2) as a function of the applied bias voltage.
ε si q N A N D –1
C j0 = A D -------- -------------------- φ
2 N A + N D 0
(3.8)
Notice that the same capacitance value is obtained when using the standard parallel-plate
capacitor equation Cj = εsi AD/Wj (with Wj given in Eq. (3.5)). Typically, the AD factor is
omitted, and Cj and Cj0 are expressed as a capacitance/unit area.
The resulting junction capacitance is plotted in the function of the bias voltage in
Figure 3.8 for a typical silicon diode found in MOS circuits. A strong nonlinear dependence can be observed. Note also that the capacitance decreases with an increasing reverse
bias: a reverse bias of 5 V reduces the capacitance by more than a factor of two.
Example 3.3 Junction Capacitance
Consider the following silicon junction diode: Cj0 = 2 × 10-3 F/m2, AD = 0.5 µm2, and φ0 =
0.64 V. A reverse bias of −2.5 V results in a junction capacitance of 0.9 × 10-3 F/m2 (0.9
fF/µm2), or, for the total diode, a capacitance of 0.45 fF.
Equation (3.7) is only valid under the condition that the pn-junction is an abrupt
junction, where the transition from n to p material is instantaneous. This is often not the
case in actual integrated-circuit pn-junctions, where the transition from n to p material can
be gradual. In those cases, a linear distribution of the impurities across the junction is a
better approximation than the step function of the abrupt junction. An analysis of the
linearly-graded junction shows that the junction capacitance equation of Eq. (3.7) still
holds, but with a variation in order of the denominator. A more generic expression for the
junction capacitance can be provided,
chapter3.fm Page 87 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
87
C j0
C j = -------------------------------( 1 – VD ⁄ φ0 )m
(3.9)
where m is called the grading coefficient and equals 1/2 for the abrupt junction and 1/3 for
the linear or graded junction. Both cases are illustrated in Figure 3.8.
Large-Signal Depletion-Region Capacitance
Figure 3.8 raises awareness to the fact that the junction capacitance is a voltage-dependent
parameter whose value varies widely between bias points. In digital circuits, operating
voltages tend to move rapidly over a wide range. Under those circumstances, it is more
attractive to replace the voltage-dependent, nonlinear capacitance Cj by an equivalent, linear capacitance Ceq. Ceq is defined such that, for a given voltage swing from voltages Vhigh
to Vlow, the same amount of charge is transferred as would be predicted by the nonlinear
model
Q j ( V high ) – Q j ( V low )
∆Q
= K eq C j0
C eq = ----------j = -------------------------------------------------∆V D
V high – V low
(3.10)
Combining Eq. (3.4) (extended to accommodate the grading coefficient m) and Eq.
(3.10) yields the value of Keq.
– φ 0m
K eq = --------------------------------------------------- [ ( φ – V high ) 1 – m – ( φ 0 – V low ) 1 – m ]
( V high – V low ) ( 1 – m ) 0
(3.11)
Example 3.4 Average Junction Capacitance
The diode of Example 3.3 is switched between 0 and −2.5 V. Compute the average junction
capacitance (m = 0.5).
For the defined voltage range and for φ0 = 0.64 V, Keq evaluates to 0.622. The average
capacitance hence equals 1.24 fF/µm2.
3.2.4
The Actual Diode—Secondary Effects
In practice, the diode current is less than what is predicted by the ideal diode equation. Not
all applied bias voltage appears directly across the junction, as there is always some voltage drop over the neutral regions. Fortunately, the resistivity of the neutral zones is generally small (between 1 and 100 Ω, depending upon the doping levels) and the voltage drop
only becomes significant for large currents (>1 mA). This effect can be modeled by adding a resistor in series with the n- and p-region diode contacts.
In the discussion above, it was further assumed that under sufficient reverse bias, the
reverse current reaches a constant value, which is essentially zero. When the reverse bias
exceeds a certain level, called the breakdown voltage, the reverse current shows a dramatic increase as shown in Figure 3.9. In the diodes found in typical CMOS processes,
this increase is caused by the avalanche breakdown. The increasing reverse bias heightens
the magnitude of the electrical field across the junction. Consequently, carriers crossing
the depletion region are accelerated to high velocity. At a critical field Ecrit , the carriers
chapter3.fm Page 88 Friday, January 18, 2002 9:00 AM
THE DEVICES
88
Chapter 3
ID (A)
0.1
0
–0.1
–25.0
–15.0
–5.0
0
5.0
Figure 3.9 I-V characteristic of junction
diode, showing breakdown under reversebias conditions (Breakdown voltage = 20 V).
VD (V)
reach a high -enough energy level that electron-hole pairs are created on collision with
immobile silicon atoms. These carriers create, in turn, more carriers before leaving the
depletion region. The value of Ecri t is approximately 2 × 105 V/cm for impurity concentrations of the order of 1016 cm−3. While avalanche breakdown in itself is not destructive and
its effects disappear after the reverse bias is removed, maintaining a diode for a long time
in avalanche conditions is not recommended as the high current levels and the associated
heat dissipation might cause permanent damage to the structure. Observe that avalanche
breakdown is not the only breakdown mechanism encountered in diodes. For highly doped
diodes, another mechanism, called Zener breakdown, can occur. Discussion of this phenomenon is beyond the scope of this text.
Finally, it is worth mentioning that the diode current is affected by the operating
temperature in a dual way:
1. The thermal voltage φT, which appears in the exponent of the current equation, is
linearly dependent upon the temperature. An increase in φT causes the current to
drop.
2. The saturation current IS is also temperature-dependent, as the thermal equilibrium
carrier concentrations increase with increasing temperature. Theoretically, the saturation current approximately doubles every 5 °C. Experimentally, the reverse current has been measured to double every 8 °C.
This dual dependence has a significant impact on the operation of a digital circuit. First of
all, current levels (and hence power consumption) can increase substantially. For instance,
for a forward bias of 0.7 V at 300 K, the current increases approximately 6%/°C, and doubles every 12 °C. Secondly, integrated circuits rely heavily on reverse-biased diodes as
isolators. Increasing the temperature causes the leakage current to increase and decreases
the isolation quality.
3.2.5
The SPICE Diode Model
In the preceding sections, we have presented a model for manual analysis of a diode circuit. For more complex circuits, or when a more accurate modeling of the diode that takes
chapter3.fm Page 89 Friday, January 18, 2002 9:00 AM
Section 3.2
The Diode
89
RS
+
VD
ID
CD
–
Figure 3.10
SPICE diode model.
into account second-order effects is required, manual circuit evaluation becomes intractable, and computer-aided simulation is necessary. While different circuit simulators have
been developed over the last decades, the SPICE program, developed at the University of
California at Berkeley, is definitely the most successful [Nagel75]. Simulating an integrated circuit containing active devices requires a mathematical model for those devices
(which is called the SPICE model in the rest of the text). The accuracy of the simulation
depends directly upon the quality of this model. For instance, one cannot expect to see the
result of a second-order effect in the simulation if this effect is not present in the device
model. Creating accurate and computation-efficient SPICE models has been a long process and is by no means finished. Every major semiconductor company has developed
their own proprietary models, which it claims have either better accuracy or computational
efficiency and robustness.
The standard SPICE model for a diode is simple, as shown in Figure 3.10. The
steady-state characteristic of the diode is modeled by the nonlinear current source ID,
which is a modified version of the ideal diode equation
I D = I S ( e V D ⁄ nφT – 1 )
(3.12)
The extra parameter n is called the emission coefficient. It equals 1 for most common diodes but can be somewhat higher than 1 for others. The resistor Rs models the
series resistance contributed by the neutral regions on both sides of the junction. For
higher current levels, this resistance causes the internal diode VD to differ from the externally applied voltage, hence causing the current to be lower than what would be expected
from the ideal diode equation.
The dynamic behavior of the diode is modeled by the nonlinear capacitance CD,
which combines the two different charge-storage effects in the diode: the space (or depletion-region) charge, and the excess minority carrier charge. Only the former was discussed
in this chapter, as the latter is only an issue under forward-biasing conditions.
τ T I S V D ⁄ nφ T
C j0
e
- + --------C D = -------------------------------m
φT
( 1 – VD ⁄ φ0 )
(3.13)
A listing of the parameters used in the diode model is given in Table 3.1. Besides the
parameter name, symbol, and SPICE name, the table contains also the default value used
by SPICE in case the parameter is left undefined. Observe that this table is by no means
complete. Other parameters are available to govern second-order effects such as break-
chapter3.fm Page 90 Friday, January 18, 2002 9:00 AM
THE DEVICES
90
Chapter 3
down, high-level injection, and noise. To be concise, we chose to limit the listing to the
parameters of direct interest to this text. For a complete description of the device models
(as well as the usage of SPICE), we refer to the numerous textbooks devoted to SPICE
(e.g., [Banhzaf92], [Thorpe92]).
Table 3.1
3.3
First-order SPICE diode model parameters.
Parameter Name
Symbol
SPICE Name
Units
Default Value
Saturation current
IS
IS
A
1.0 E−14
Emission coefficient
n
N
–
1
Series resistance
RS
RS
Ω
0
Transit time
τT
TT
s
0
Zero-bias junction
capacitance
Cj0
CJ0
F
0
Grading coefficient
m
M
–
0.5
Junction potential
φ0
VJ
V
1
The MOS(FET) Transistor
The metal-oxide-semiconductor field-effect transistor (MOSFET or MOS, for short) is
certainly the workhorse of contemporary digital design. Its major asset from a digital perspective is that the device performs very well as a switch, and introduces little parasitic
effects. Other important advantages are its integration density combined with a relatively
“simple” manufacturing process, which make it possible to produce large and complex
circuits in an economical way.
Following the approach we took for the diode, we restrict ourselves in this section to
a general overview of the transistor and its parameters. After a generic overview of the
device, we present an analytical description of the transistor from a static (steady-state)
and dynamic (transient) viewpoint. The discussion concludes with an enumeration of
some second-order effects and the introduction of the SPICE MOS transistor models.
3.3.1
A First Glance at the Device
The MOSFET is a four terminal device. The voltage applied to the gate terminal determines if and how much current flows between the source and the drain ports. The body
represents the fourth terminal of the transistor. Its function is secondary as it only serves to
modulate the device characteristics and parameters.
At the most superficial level, the transistor can be considered to be a switch. When a
voltage is applied to the gate that is larger than a given value called the threshold voltage
VT, a conducting channel is formed between drain and source. In the presence of a voltage
difference between the latter two, current flows between them. The conductivity of the
channel is modulated by the gate voltage—the larger the voltage difference between gate
and source, the smaller the resistance of the conducting channel and the larger the current.
chapter3.fm Page 91 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
91
When the gate voltage is lower than the threshold, no such channel exists, and the switch
is considered open.
Two types of MOSFET devices can be identified. The NMOS transistor consists of
n+ drain and source regions, embedded in a p-type substrate. The current is carried by
electrons moving through an n-type channel between source and drain. This is in contrast
with the pn-junction diode, where current is carried by both holes and electrons. MOS
devices can also be made by using an n-type substrate and p+ drain and source regions. In
such a transistor, current is carried by holes moving through a p-type channel. The device
is called a p-channel MOS, or PMOS transistor. In a complementary MOS technology
(CMOS), both devices are present. The cross-section of a contemporary dual-well CMOS
process was presented in Chapter 2, and is repeated here for convenience (Figure 3.11).
gate-oxide
Tungsten
TiSi2
AlCu
SiO2
poly
p-well
SiO2
n-well
n+
p-epi
p+
p+
Figure 3.11
Cross-section of contemporary dual-well CMOS process.
Circuit symbols for the various MOS transistors are shown in Figure 3.12. As mentioned earlier, the transistor is a four-port device with gate, source, drain, and body terminals (Figures a and c). Since the body is generally connected to a dc supply that is identical
for all devices of the same type (GND for NMOS, Vdd for PMOS), it is most often not
shown on the schematics (Figures b and d). If the fourth terminal is not shown, it is
assumed that the body is connected to the appropriate supply.
G
S
G
D
B
D
S
(a) NMOS transistor
as 4-terminal device
(b) NMOS transistor
as 3-terminal device
S
G
S
D
B
(a) PMOS transistor
as 4-terminal device
S
D
(d) PMOS transistor
as 3-terminal device
Figure 3.12 Circuit symbols for
MOS transistors.
chapter3.fm Page 92 Friday, January 18, 2002 9:00 AM
THE DEVICES
92
3.3.2
Chapter 3
The MOS Transistor under Static Conditions
In the derivation of the static model of the MOS transistor, we concentrate on the NMOS
device. All the arguments made are valid for PMOS devices as well as will be discussed at
the end of the section.
The Threshold Voltage
Consider first the case where VGS = 0 and drain, source, and bulk are connected to ground.
The drain and source are connected by back-to-back pn-junctions (substrate-source and
substrate-drain). Under the mentioned conditions, both junctions have a 0 V bias and can
be considered off, which results in an extremely high resistance between drain and source.
Assume now that a positive voltage is applied to the gate (with respect to the
source), as shown in Figure 3.13. The gate and substrate form the plates of a capacitor
with the gate oxide as the dielectric. The positive gate voltage causes positive charge to
accumulate on the gate electrode and negative charge on the substrate side. The latter
manifests itself initially by repelling mobile holes. Hence, a depletion region is formed
below the gate. This depletion region is similar to the one occurring in a pn-junction
diode. Consequently, similar expressions hold for the width and the space charge per unit
area. Compare these expressions to Eq. (3.4) and Eq. (3.5).
Wd =
2ε si φ
-----------qN A
(3.14)
2qN A ε si φ
(3.15)
and
Qd =
with NA the substrate doping and φ the voltage across the depletion layer (i.e., the potential
at the oxide-silicon boundary).
As the gate voltage increases, the potential at the silicon surface at some point
reaches a critical value, where the semiconductor surface inverts to n-type material. This
+
S
VGS
–
D
G
n+
n+
Depletion
region
n-channel
p-substrate
B
Figure 3.13
NMOS transistor for positive VGS, showing depletion region and induced channel.
chapter3.fm Page 93 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
93
point marks the onset of a phenomenon known as strong inversion and occurs at a voltage
equal to twice the Fermi Potential (Eq. (3.16)) (φF ≈ −0.3 V for typical p-type silicon substrates):
N
φ F = – φ T ln(------A)
ni
(3.16)
Further increases in the gate voltage produce no further changes in the depletionlayer width, but result in additional electrons in the thin inversion layer directly under the
oxide. These are drawn into the inversion layer from the heavily doped n+ source region.
Hence, a continuous n-type channel is formed between the source and drain regions, the
conductivity of which is modulated by the gate-source voltage.
In the presence of an inversion layer, the charge stored in the depletion region is
fixed and equals
Q B0 =
2qN A ε si – 2 φ F
(3.17)
This picture changes somewhat in case a substrate bias voltage VSB is applied (VSB is normally positive for n-channel devices). This causes the surface potential required for strong
inversion to increase and to become |–2φF + VSB|. The charge stored in the depletion
region now is expressed by Eq. (3.18)
QB =
2qN A ε si ( – 2 φ F + V SB )
(3.18)
The value of VGS where strong inversion occurs is called the threshold voltage VT .
VT is a function of several components, most of which are material constants such as the
difference in work-function between gate and substrate material, the oxide thickness, the
Fermi voltage, the charge of impurities trapped at the surface between channel and gate
oxide, and the dosage of ions implanted for threshold adjustment. From the above arguments, it has become clear that the source-bulk voltage VSB has an impact on the threshold.
as well. Rather than relying on a complex (and hardly accurate) analytical expression for
the threshold, we rely on an empirical parameter called VT0, which is the threshold voltage
for VSB = 0, and is mostly a function of the manufacturing process. The threshold voltage
under different body-biasing conditions can then be determined in the following manner,
V T = V T0 + γ (
– 2φ F + V SB –
– 2φ F )
(3.19)
The parameter γ (gamma) is called the body-effect coefficient, and expresses the impact of
changes in VSB. Observe that the threshold voltage has a positive value for a typical
NMOS device, while it is negative for a normal PMOS transistor.
chapter3.fm Page 94 Friday, January 18, 2002 9:00 AM
THE DEVICES
94
The effect of the well bias on the
threshold voltage of an NMOS
transistor is plotted in for typical
values of |–2φF| = 0.6 V and γ =
0.4 V0.5. A negative bias on the
well or substrate causes the
threshold to increase from 0.45 V
to 0.85 V. Note also that VSB
always has to be larger than -0.6 V
in an NMOS. If not, the sourcebody diode becomes forward
biased, which deteriorates the
transistor operation.
0.9
0.85
0.8
0.75
0.65
T
V (V)
0.7
0.6
0.55
0.5
0.45
0.4
-2.5
-2
-1.5
-1
V
Figure 3.14
BS
-0.5
Chapter 3
0
(V)
Effect of body-bias on threshold.
Example 3.5 Threshold Voltage of a PMOS Transistor
An PMOS transistor has a threshold voltage of -0.4 V, while the body-effect coefficient
equals -0.4. Compute the threshold voltage for VSB = -2.5 V. 2φF = 0.6 V.
Using Eq. (3.19), we obtain VT(-2.5 V) = -0.4 - 0.4 × ((2.5+0.6)0.5 - 0.60.5) V = -0.79 V,
which is twice the threshold under zero-bias conditions!
Resistive Operation
Assume now that VGS > VT and that a small voltage, VDS, is applied between drain and
source. The voltage difference causes a current ID to flow from drain to source (Figure
3.15). Using a simple analysis, a first-order expression of the current as a function of VGS
and VDS can be obtained.
VGS
VDS
S
G
n+
– V(x)
ID
D
+
n+
L
x
p-substrate
B
Figure 3.15
voltages.
NMOS transistor with bias
At a point x along the channel, the voltage is V(x), and the gate-to-channel voltage at
that point equals VGS – V(x). Under the assumption that this voltage exceeds the threshold
voltage all along the channel, the induced channel charge per unit area at point x can be
computed.
chapter3.fm Page 95 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
95
Q i ( x ) = – C ox [ V GS – V ( x ) – V T ]
(3.20)
Cox stands for the capacitance per unit area presented by the gate oxide, and equals
ε ox
C ox = -----t ox
(3.21)
with εox = 3.97 × εo = 3.5 × 10-11 F/m the oxide permittivity, and tox is the thickness of the
oxide. The latter which is 10 nm (= 100 Å) or smaller for contemporary processes. For an
oxide thickness of 5 nm, this translates into an oxide capacitance of 7 fF/µm2.
The current is given as the product of the drift velocity of the carriers υn and the
available charge. Due to charge conservation, it is a constant over the length of the channel. W is the width of the channel in a direction perpendicular to the current flow.
ID = – υ n ( x )Q i ( x )W
(3.22)
The electron velocity is related to the electric field through a parameter called the mobility
µn (expressed in m2/V⋅s). The mobility is a complex function of crystal structure, and local
electrical field. In general, an empirical value is used.
υ n = – µ n ξ ( x ) = µ n dV
dx
(3.23)
Combining Eq. (3.20) − Eq. (3.23) yields
I D dx = µ n C ox W ( V GS – V – V T )dV
(3.24)
Integrating the equation over the length of the channel L yields the voltage-current relation
of the transistor.
V DS 2
V DS 2
----- ( V GS – V T )V DS – --------- = k n ( V GS – V T )V DS – -------I D = k'n W
2
2
L
(3.25)
k'n is called the process transconductance parameter and equals
µ n ε ox
k' n = µ n C ox = -----------t ox
(3.26)
The product of the process transconductance k'n and the (W/L) ratio of an (NMOS) transistor is called the gain factor kn of the device. For smaller values of VDS, the quadratic
factor in Eq. (3.25) can be ignored, and we observe a linear dependence between VDS and
ID. The operation region where Eq. (3.25) holds is hence called the resistive or linear
region. One of its main properties is that it displays a continuous conductive channel
between source and drain regions.
NOTICE: The W and L parameters in Eq. (3.25) represent the effective channel width
and length of the transistor. These values differ from the dimensions drawn on the layout
due to effects such as lateral diffusion of the source and drain regions (L), and the
encroachment of the isolating field oxide (W). In the remainder of the text, W and L will
chapter3.fm Page 96 Friday, January 18, 2002 9:00 AM
THE DEVICES
96
Chapter 3
always stand for the effective dimensions, while a d subscript will be used to indicate the
drawn size. The following expressions related the two parameters, with ∆W and ∆L
parameters of the manufacturing process:
W = W d – ∆W
L = L d – ∆L
(3.27)
The Saturation Region
As the value of the drain-source voltage is further increased, the assumption that the channel voltage is larger than the threshold all along the channel ceases to hold. This happens
when VGS − V(x) < VT. At that point, the induced charge is zero, and the conducting channel disappears or is pinched off. This is illustrated in Figure 3.16, which shows (in an
VGS
VDS > VGS – VT
G
D
S
n+
Figure 3.16
–
VGS - VT
+
n+
NMOS transistor under pinch-off conditions.
exaggerated fashion) how the channel thickness gradually is reduced from source to drain
until pinch-off occurs. No channel exists in the vicinity of the drain region. Obviously, for
this phenomenon to occur, it is essential that the pinch-off condition be met at the drain
region, or
VGS − VDS ≤ VT.
(3.28)
Under those circumstances, the transistor is in the saturation region, and Eq. (3.25)
no longer holds. The voltage difference over the induced channel (from the pinch-off point
to the source) remains fixed at VGS − VT, and consequently, the current remains constant
(or saturates). Replacing VDS by VGS − VT in Eq. (3.25) yields the drain current for the saturation mode. It is worth observing that, to a first agree, the current is no longer a function
of VDS. Notice also the squared dependency of the drain current with respect to the control
voltage VGS.
k'
----- ( V – V T ) 2
ID = -----n- W
2 L GS
(3.29)
chapter3.fm Page 97 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
97
Channel-Length Modulation
The latter equation seems to suggest that the transistor in the saturation mode acts as a perfect current source — or that the current between drain and source terminal is a constant,
independent of the applied voltage over the terminals. This not entirely correct. The effective length of the conductive channel is actually modulated by the applied VDS: increasing
VDS causes the depletion region at the drain junction to grow, reducing the length of the
effective channel. As can be observed from Eq. (3.29), the current increases when the length
factor L is decreased. A more accurate description of the current of the MOS transistor is
therefore given in Eq. (3.30).
I D = I D ′ ( 1 + λV DS )
(3.30)
with ID’ the current expressions derived earlier, and λ an empirical parameter, called the
channel-length modulation. Analytical expressions for λ have proven to be complex and
inaccurate. λ varies roughly with the inverse of the channel length. In shorter transistors,
the drain-junction depletion region presents a larger fraction of the channel, and the channel-modulation effect is more pronounced. It is therefore advisable to resort to long-channel transistors if a high-impedance current source is needed.
Velocity Saturation
The behavior of transistors with very short channel lengths (called short-channel devices)
deviates considerably from the resistive and saturated models, presented in the previous
paragraphs. The main culprit for this deficiency is the velocity saturation effect. Eq. (3.23)
states that the velocity of the carriers is proportional to the electrical field, independent of
the value of that field. In other words, the carrier mobility is a constant. However, at high
field strengths, the carriers fail to follow this linear model. In fact, when the electrical field
along the channel reaches a critical value ξc, the velocity of the carriers tends to saturate
due to scattering effects (collisions suffered by the carriers). This is illustrated in Figure
3.17.
υn (m/s)
υsat = 105
Constant velocity
Constant mobility (slope = µ)
Figure 3.17
ξc = 1.5
Velocity-saturation effect.
ξ (V/µm)
For p-type silicon, the critical field at which electron saturation occurs is around 1.5
× 106 V/m (or 1.5 V/µm), and the saturation velocity υsat approximately equals 105 m/s.
This means that in an NMOS device with a channel length of 1 µm, only a couple of volts
between drain and source are needed to reach the saturation point. This condition is easily
met in current short-channel devices. Holes in a n-type silicon saturate at the same velocity, although a higher electrical field is needed to achieve saturation. Velocity-saturation
effects are hence less pronounced in PMOS transistors.
chapter3.fm Page 98 Friday, January 18, 2002 9:00 AM
THE DEVICES
98
Chapter 3
This effect has a profound impact on the operation of the transistor. We will illustrate this with a first-order derivation of the device characteristics under velocity-saturating conditions [Ko89]. The velocity as a function of the electrical field, plotted in Figure
3.17, can be roughly approximated by the following expression:
µn ξ
- for ξ ≤ ξ c
υ = -------------------1 + ξ ⁄ ξc
= υ sat
for
(3.31)
ξ ≥ ξc
The continuity requirement between the two regions dictates that ξc = 2υsat/µn. Re-evaluation of Eq. (3.20) and Eq. (3.22) in light of revised velocity formula leads to a modified
expression of the drain current in the resistive region:
V DS 2
W
I D = κ(V DS)µ n C ox ----- ( V GS – V T )V DS – --------2
L
(3.32)
1
κ(V) = -----------------------------1 + ( V ⁄ ξc L )
(3.33)
with
κ is a measure of the degree of velocity saturation, since VDS/L can be interpreted as the
average field in the channel. In case of long-channel devices (large values of L) or small
values of VDS, κ approaches 1 and Eq. (3.32) simplifies to the traditional current equation
for the resistive operation mode. For short-channel devices, κ is smaller than 1, which
means that the delivered current is smaller than what would be normally expected.
When increasing the drain-source voltage, the electrical field in the channel will
ultimately reach the critical value, and the carriers at the drain become velocity saturated.
The saturation drain voltage VDSAT can be calculated by equating the current at the drain to
the current given by Eq. (3.32) for VDS = VDSAT. The former is derived from Eq. (3.22),
assuming that the drift velocity is saturated and equals υsat.
IDSAT = υ sat C ox W ( V GT – V DSAT )
V DSAT 2
W
= κ(V DSAT)µ n C ox ----- V GT V DSAT – -------------2
L
(3.34)
VGT is a shorthand notation for VGS - VT. After some algebra, we obtain
V DSAT = κ(V GT)V GT
(3.35)
Further increasing the drain-source voltage does not yield more current (to a first degree)
and the transistor current saturates at IDSAT. This leads to some interesting observations:
• For a short-channel device and for large enough values of VGT, κ(VGT) is substantially smaller than 1, hence VDSAT < VGT. The device enters saturation before VDS
reaches VGS - VT. Short-channel devices therefore experience an extended saturation
chapter3.fm Page 99 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
99
ID
Long-channel device
VGS = VDD
Short-channel device
VDSAT
Figure 3.18 Short-channel devices display an
extended saturation region due to velocity-saturation.
VGS - VT
VDS
region, and tend to operate more often in saturation conditions than their long-channel counterparts, as is illustrated in Figure 3.18.
• The saturation current IDSAT displays a linear dependence with respect to the gatesource voltage VGS, which is in contrast with the squared dependence in the longchannel device. This reduces the amount of current a transistor can deliver for a
given control voltage. On the other hand, reducing the operating voltage does not
have such a significant effect in submicron devices as it would have in a long-channel transistor.
The equations above ignore that a larger portion of the channel becomes velocity-saturated with a further increase of VDS. From a modeling perspective, it appears as though the
effective channel is shortening with increasing VDS, similar in effect to the channel-length
modulation. The resulting increase in current is easily accommodated by introducing an
extra (1 + λ × VDS) multiplier.
Thus far we have only considered the effects of the tangential field along the channel due to the VDS, when considering velocity-saturation effects. However, there also
exists a normal (vertical) field originating from the gate voltage that further inhibits channel carrier mobility. This effect, which is called mobility degradation, reduces the surface
mobility with respect to the bulk mobility. Eq. (3.36) provides a simple estimation of the
mobility reduction,
µ n0
µ n, eff = --------------------------------------1 + η ( V GS – V T )
(3.36)
with µn0 the bulk mobility and η an empirical parameter. A typical approach is to use
derive the actual value of µ for a given field strength from tables or empirical charts.
Readers interested in a more in-depth perspective on the short-channel effects in
MOS transistors are referred to the excellent reference works on this topic, such as
[Ko89].
Velocity Saturation — Revisited
Unfortunately, the drain-current equations Eq. (3.32) and Eq. (3.33) are complex expressions of VGS and VDS, which makes them rather unwieldy for a first-order manual analysis.
A substantially simpler model can be obtained by making two assumptions:
chapter3.fm Page 100 Friday, January 18, 2002 9:00 AM
THE DEVICES
100
Chapter 3
1. The velocity saturates abruptly at ξc, and is approximated by the following expression:
υ = µn ξ
= υ sat = µ n ξ c
for ξ ≤ ξc
(3.37)
for ξ ≥ ξ c
2. The drain-source voltage VDSAT at which the critical electrical field is reached and
velocity saturation comes into play is constant and is approximated by Eq. (3.38).
From Eq. (3.35), it can be observed that this assumption is reasonable for larger values of VGT (>> ξcL).
Lυ sat
V DSAT = Lξ c = -----------µn
(3.38)
Under these circumstances, the current equations for the resistive region remain
unchanged from the long-channel model. Once VDSAT is reached, the current abruptly saturates. The value for IDSAT at that point can be derived by plugging the saturation voltage
into the current equation for the resistive region (Eq. (3.25)).
I DSAT = I D ( V DS = V DSAT )
2
V DSAT
----- ( V GS – V T )V DSAT – -------------= µ n C ox W
L
2
(3.39)
V DSAT
= υ sat C ox W VGS – V T – -------------
2
This model is truly first-order and empirical. The simplified velocity model causes
substantial deviations in the transition zone between linear and velocity-saturated regions.
Yet, by carefully choosing the model parameters, decent matching can be obtained with
empirical data in the other operation regions, as will be shown in one of the following sections. Most importantly, the equations are coherent with the familiar long-channel equations, and provide the digital designer with a much needed tool for intuitive understanding
and interpretation.
Drain Current versus Voltage Charts
The behavior for the MOS transistor in the different operation regions is best understood
by analyzing its ID-VDS curves, which plot ID versus VDS with VGS as a parameter. Figure
3.19 shows these charts for two NMOS transistors, implemented in the same technology
and with the same W/L ratio. One would hence expect both devices to display identical IV characteristics, The main difference however is that the first device has a long channel
length (Ld = 10 µm), while the second transistor is a short channel device (Ld = 0.25 µm),
and experiences velocity saturation.
Consider first the long-channel device. In the resistive region, the transistor behaves
like a voltage-controlled resistor, while in the saturation region, it acts as a voltage-controlled current source (when the channel-length modulation effect is ignored). The transi-
chapter3.fm Page 101 Friday, January 18, 2002 9:00 AM
Section 3.3
x 10
101
-4
2.5
-4
VGS = 2.5 V
VDS = VGS-VT
VGS = 2.5 V
5
Saturation
Resistive
VGS = 2.0 V
3
VGS = 1.5 V
2
VGS = 2.0 V
1.5
I D (A)
Quadratic dependence
2
4
I D (A)
x 10
VGS = 1.5 V
1
VGS = 1.0 V
0.5
1
VGS = 1.0 V
0
0
0.5
1
1.5
2
Linear dependence
6
The MOS(FET) Transistor
0
2.5
0
0.5
1
VDS (V)
1.5
2
2.5
VDS (V)
(a) Long-channel transistor (Ld = 10 µm)
(b) Short-channel transistor (Ld = 0.25 µm)
Figure 3.19 I-V characteristics of long- and a short-channel NMOS transistors in a 0.25 µm CMOS technology. The (W/L)
ration of both transistors is identical and equals 1.5
tion between both regions is delineated by the VDS = VGS - VT curve. The squared
dependence of ID as a function of VGS in the saturation region — typical for a long channel
device — is clearly observable from the spacing between the different curves. The linear
dependence of the saturation current with respect to VGS is apparent in the short-channel
device of b. Notice also how velocity-saturation causes the device to saturate for substantially smaller values of VDS. This results in a substantial drop in current drive for high voltage levels. For instance, at (VGS = 2.5 V, VDS = 2.5 V), the drain current of the short
transistor is only 40% of the corresponding value of the longer device (220 µA versus 540
µA).
-4
6
-4
x 10
2.5
x 10
5
2
4
linear
I D (A)
I D (A)
1.5
3
1
2
quadratic
0.5
1
quadratic
0
0
0.5
1
1.5
2
VGS (V)
(a) Long-channel device (Ld = 10 µm)
2.5
0
0
0.5
1
1.5
2
2.5
VGS (V)
(b) Short-channel device (Ld = 0.25 µm)
Figure 3.20 NMOS transistor ID-VGS characteristic for long and short-channel devices (0.25 µm CMOS
technology). W/L = 1.5 for both transistors and VDS = 2.5 V.
chapter3.fm Page 102 Friday, January 18, 2002 9:00 AM
THE DEVICES
102
Chapter 3
The difference in dependence upon VGS between long- and short-channel devices is
even more pronounced in another set of simulated charts that plot ID as a function of VGS
for a fixed value of VDS (≥ VGS — hence ensuring saturation) (Figure 3.20). A quadratic
versus linear dependence is apparent for larger values of VGS.
All the derived equations hold for the PMOS transistor as well. The only difference
is that for PMOS devices, the polarities of all voltages and currents are reversed. This
is illustrated in Figure 3.21, which plots the ID-VDS characteristics of a minimum-size
PMOS transistor in our generic 0.25 µm CMOS process. The curves are in the third quadrant as ID, VDS, and VGS are all negative. Interesting to observe is also that the effects of
velocity saturation are less pronounced than in the CMOS devices. This can be attributed
to the higher value of the critical electrical field, resulting from the smaller mobility of
holes versus electrons.
-4
0
x 10
VGS = -1.0 V
-0.2
VGS = -1.5 V
I D (A)
-0.4
VGS = -2.0 V
-0.6
-0.8
-1
-2.5
VGS = -2.5 V
-2
-1.5
-1
-0.5
0
Figure 3.21 I-V characteristics of (Wd=0.375 µm,
Ld=0.25 µm) PMOS transistor in 0.25 µm CMOS
process. Due to the smaller mobility, the maximum
current is only 42% of what is achieved by a similar
NMOS transistor.
VDS (V)
Subthreshold Conduction
A closer inspection of the ID-VGS curves of Figure 3.20 reveals that the current does not
drop abruptly to 0 at VGS = VT . It becomes apparent that the MOS transistor is already partially conducting for voltages below the threshold voltage. This effect is called subthreshold or weak-inversion conduction. The onset of strong inversion means that ample carriers
are available for conduction, but by no means implies that no current at all can flow for
gate-source voltages below VT, although the current levels are small under those conditions. The transition from the on- to the off-condition is thus not abrupt, but gradual.
To study this effect in somewhat more detail, we redraw the ID versus VGS curve of
Figure 3.20b on a logarithmic scale as shown in Figure 3.22. This confirms that the current
does not drop to zero immediately for VGS < VT, but actually decays in an exponential
fashion, similar to the operation of a bipolar transistor.2 In the absence of a conducting
channel, the n+ (source) - p (bulk) - n+ (drain) terminals actually form a parasitic bipolar
transistor. The current in this region can be approximated by the expression
2
Discussion of the operation of bipolar transistors is out of the scope of this textbook. We refer to various textbooks on semiconductor devices, or to the additional information that is available on the web-site of this
book.
chapter3.fm Page 103 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
103
-2
10
-4
10
Linear region
Quadratic region
-6
I D (A)
10
-8
10
Subthreshold exponential region
-10
10
VT
-12
10
Figure 3.22 ID current versus VGS
(on logarithmic scale), showing the
exponential characteristic of the
subthreshold region.
0
0.5
1
1.5
2
2.5
VGS (V)
ID = IS e
V GS
---------------nkT ⁄ q
1 – e
V DS
– -----------kT ⁄ q
(3.40)
where IS and n are empirical parameters, with n ≥ 1 and typically ranging around 1.5.
In most digital applications, the presence of subthreshold current is undesirable as it
detracts from the ideal switch-like behavior that we like to assume for the MOS transistor.
We would rather have the current drop as fast as possible once the gate-source voltage
falls below VT. The (inverse) rate of decline of the current with respect to VGS below VT
hence is a quality measure of a device. It is often quantified by the slope factor S, which
measures by how much VGS has to be reduced for the drain current to drop by a factor of
10. From Eq. (3.40), we find
kT
S = n ------ ln ( 10 )
q
(3.41)
with S is expressed in mV/decade. For an ideal transistor with the sharpest possible rolloff, n = 1 and (kT/q)ln(10) evaluates to 60 mV/decade at room temperature, which means
that the subthreshold current drops by a factor of 10 for a reduction in VGS of 60 mV.
Unfortunately, n is larger than 1 for actual devices and the current falls at a reduced rate
(90 mV/decade for n = 1.5). The current roll-off is further affected in a negative sense by
an increase in the operating temperature (most integrated circuits operate at temperatures
considerably beyond room temperature). The value of n is determined by the intrinsic
device topology and structure. Reducing its value hence requires a different process technology, such as silicon-on-insulator.
Subthreshold current has some important repercussions. In general, we want the current through the transistor to be as close as possible to zero at VGS = 0. This is especially
important in the so-called dynamic circuits, which rely on the storage of charge on a
capacitor and whose operation can be severely degraded by subthreshold leakage. Achieving this in the presence of subthreshold current requires a firm lower bound on the value of
the threshold voltage of the devices.
chapter3.fm Page 104 Friday, January 18, 2002 9:00 AM
THE DEVICES
104
Chapter 3
Example 3.6 Subthreshold Slope
For the example of Figure 3.22, a slope of 89.5 mV/decade is observed (between 0.2 and 0.4
V). This is equivalent to an n-factor of 1.49.
In Summary – Models for Manual Analysis
The preceding discussions made it clear that the deep-submicron transistor is a complex
device. Its behavior is heavily non-linear and is influenced by a large number of secondorder effects. Fortunately, accurate circuit-simulation models have been developed that
make it possible to predict the behavior of a device with amazing precision over a large
range of device sizes, shapes, and operation modes, as we will discuss later in this chapter.
While excellent from an accuracy perspective, these models fail in providing a designer
with an intuitive insight in the behavior of a circuit and its dominant design parameters.
Such an understanding is necessary in the design analysis and optimization process. A
designer who misses a clear vision on what drives and governs the circuit operation by
necessity resorts on a lengthy trial by error optimization process, that most often leads to
an inferior solution.
The obvious question is now how to abstract the behavior of our MOS transistor into
a simple and tangible analytical model that does not lead to hopelessly complex equations,
yet captures the essentials of the device. It turns out that the first-order expressions,
derived earlier in the chapter, can be combined into a single expression that meets these
goals. The model presents the transistor as a single current source (Figure 3.23), the value
of which is given defined in the Figure. The reader can verify that, depending upon the
operating condition, the model simplifies into either Eq. (3.25), Eq. (3.29), or Eq. (3.39)
(corrected for channel-length modulation), depending upon operating conditions.
I D = 0 for V GT ≤ 0
2
V min
W
( 1 + λV DS ) for V GT ≥ 0
I D = k′ ----- V GT V min – ---------2
L
G
ID
S
D
B
with V min = min ( V GT, V DS, V DSAT ),
V GT = V GS – V T ,
and V T = V T0 + γ (
Figure 3.23
– 2φ F + V SB –
– 2φ F )
A unified MOS model for manual analysis.
Besides being a function of the voltages at the four terminals of the transistor, the
model employs a set of five parameters: VTO, γ, VDSAT, k’, and λ. In principle, it would be
possible to determine these parameters from the process technology and from the device
physics equations. The complexity of the device makes this a precarious task. A more
rewarding approach is to choose the values such that a good matching with the actual
device characteristics is obtained. More significantly, the model should match the best in
chapter3.fm Page 105 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
105
the regions that matter the most. In digital circuits, this in the region of high VGS and VDS.
The performance of an MOS digital circuit is primarily determined by the maximum
available current (i.e., the current obtained for VGS = VDS = supply voltage). A good
matching in this region is therefore essential.
Example 3.7 Manual Analysis Model for 0.25 µm CMOS Process3
Based on the simulated ID-VDS and ID-VGS plots of a (Wd = 0.375 µm, Ld = 0.25 µm) transistor,
implemented in our generic 0.25 micron CMOS process (Figure 3.19, Figure 3.20), we have
derived a set of device parameters to match well in the (VDS = 2.5 V, VGS = 2.5 V) region —
2.5 V being the typical supply voltage for this process. The resulting characteristics are plotted in Figure 3.24 for the NMOS transistor, and compared to the simulated values. Overall, a
2.5
x 10
-4
2
I
D
(A)
1.5
1
Figure 3.24 Correspondence between simple model
(solid line) and SPICE simulation (dotted) for minimumsize NMOS transistor (Wd=0.375 µm, Ld=0.25 µm).
Observe the discrepancy in the transition zone between
resistive and velocity saturation.
0.5
0
0
0.5
1
1.5
V
DS
2
2.5
(V)
good correspondence can be observed with the exception of the transition region between
resistive and velocity-saturation. This discrepancy, which is due the simple velocity model of
Eq. (3.37) as explained earlier, is acceptable as it occurs in the lower value-range of VDS. It
demonstrates that our model, while simple, manages to give a fair indication of the overall
behavior of the device.
Design Data — Transistor Model for Manual Analysis
Table 3.2 tabulates the obtained parameter values for the minimum-sized NMOS and a similarly sized PMOS device in our generic 0.25 µm CMOS process. These values will be used as
generic model-parameters in later chapters.
Table 3.2
Parameters for manual model of generic 0.25 µm CMOS process (minimum length device).
VT0 (V)
γ (V0.5)
VDSAT (V)
k' (A/V2)
λ (V−1)
NMOS
0.43
0.4
0.63
115 × 10−6
0.06
PMOS
−0.4
-0.4
-1
-30 × 10−6
-0.1
3
A MATLAB implementation of the model is available on the web-site of the textbook.
chapter3.fm Page 106 Friday, January 18, 2002 9:00 AM
THE DEVICES
106
Chapter 3
A word of caution — The model presented here is derived from the characteristics
of a single device with a minimum channel-length and width. Trying to extrapolate this
behavior to devices with substantially different values of W and L will probably lead to
sizable errors. Fortunately, digital circuits typically use only minimum-length devices as
these lead to the smallest implementation area. Matching for these transistors will typically be acceptable. It is however advisable to use a different set of model parameters for
devices with dramatically different size- and shape-factors.
The presented current-source model will prove to be very useful in the analysis of
the basic properties and metrics of a simple digital gate, yet its non-linearity makes it
intractable for anything that is somewhat more complex. We therefore introduce an even
more simplified model that has the advantage of being linear and straightforward. It is
based on the underlying assumption in most digital designs that the transistor is nothing
more than a switch with an infinite off-resistance, and a finite on-resistance Ron.
VGS ≥ VT
Ron
S
D
Figure 3.25
NMOS transistor modeled as a switch.
The main problem with this model is that Ron is still time-variant, non-linear and
depending upon the operation point of the transistor. When studying digital circuits in the
transient mode — which means while switching between different logic states — it is
attractive to assume Ron as a constant and linear resistance Req, chosen so that the final
result is similar to what would be obtained with the original transistor. A reasonable
approach in that respect is to use the average value of the resistance over the operation
region of interest, or even simpler, the average value of the resistances at the end-points of
the transition. The latter assumption works well if the resistance does not experience any
strong non-linearities over the range of the averaging interval.
R eq = averaget = t
1 …t 2
1 ( R on ( t ) ) = ------------t2 – t 1
t2
t2
1 - V
DS ( t )
R on(t) dt = --------------------------- dt
t2 – t1 ID ( t )
t1
∫
∫
t1
(3.42)
1
≈ --- ( R on(t 1) + R on(t 2) )
2
Example 3.8 Equivalent resistance when (dis)charging a capacitor
One of the most common scenario’s in contemporary digital circuits is the discharging of a
capacitor from VDD to GND through an NMOS transistor with its gate voltage set to VDD, or
vice-versa the charging of the capacitor to VDD through a PMOS with its gate at GND. Of special interest is the point where the voltage on the capacitor reaches the mid-point (VDD/2) —
this is by virtue of the definition of the propagation delay as introduced in Chapter 2. Assuming that the supply voltage is substantially larger than the velocity-saturation voltage VDSAT of
the transistor, it is fair to state that the transistor stays in velocity saturation for the entire
chapter3.fm Page 107 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
107
duration of the transition. This scenario is plotted in for the case of an NMOS discharging a
capacitor from VDD to VDD/2.
ID
VDS (VDD→VDD/2)
VDD
VGS = VDD
Rmid
ID
R0
VDS
(a) schematic
VDD/2
VDD
(b) trajectory traversed on ID-VDS curve.
Figure 3.26 Discharging a capacitor through an NMOS transistor: Schematic (a) and I-V trajectory (b). The
instantaneous resistance of the transistor equals (VDS/ID) and is visualized by the angle with respect to the y-axis.
With the aid of Eq. (3.42) and Eq. , we can derive the value of the equivalent resistance, which averages the resistance of the device over the interval.
V DD ⁄ 2
Req
1
= -------------------– V DD ⁄ 2
∫
V DD
V
7
3 VDD
- 1 – --- λV DD
----------------------------------- dV ≈ --- -----------
9
4 I DSAT
I DSAT ( 1 + λV )
(3.43)
2
V DSAT
W
with I DSAT = k' ----- ( VDD – VT )V DSAT – -------------L
2
A similar result can be obtained by just averaging the values of the resistance at the end points
(and simplifying the result using a Taylor expansion):
VDD ⁄ 2
V DD
VDD
1
≈ 3--- ------------ 1 – 5--- λV DD
R eq = --- ----------------------------------------+ -----------------------------------------------
6
2 I DSAT ( 1 + λV DD ) I DSAT ( 1 + λVDD ⁄ 2 )
4 I DSAT
(3.44)
A number of conclusions are worth drawing from the above expressions:
• The resistance is inversely proportional to the (W/L) ratio of the device. Doubling the transistor width halves the resistance.
• For VDD >> VT + VDSAT/2, the resistance becomes virtually independent of the supply voltage. This is confirmed in halves, which plots the simulated equivalent resistance as a function of the supply voltage VDD. Only a minor improvement in resistance, attributable to the
channel-length modulation, can be observed when raising the supply voltage.
• Once the supply voltage approaches VT, a dramatic increase in resistance can be observed.
chapter3.fm Page 108 Friday, January 18, 2002 9:00 AM
THE DEVICES
108
7
x 10
Chapter 3
5
6
R eq (Ohm)
5
4
3
2
1
0
0.5
1
1.5
V
DD
2
2.5
(V)
Figure 3.27 Simulated equivalent
resistance of a minimum size NMOS
transistor in 0.25 µm CMOS process as a
function of VDD
(VGS = VDD, VDS = VDD →VDD/2).
Design Data — Equivalent Resistance Model
Table 3.3 enumerates the equivalent resistances obtained by simulation of our generic 0.25 µm
CMOS process. These values will come in handy when analyzing the performance of CMOS
gates in later chapters.
Table 3.3 Equivalent resistance Req (W/L= 1) of NMOS and PMOS transistors in 0.25 µm CMOS process (with
L = Lmin). For larger devices, divide Req by W/L.
VDD (V)
1
1.5
2
2.5
NMOS (kΩ)
35
19
15
13
PMOS (kΩ)
115
55
38
31
3.3.3
Dynamic Behavior
The dynamic response of a MOSFET transistor is a sole function of the time it takes to
(dis)charge the parasitic capacitances that are intrinsic to the device, and the extra capacitance introduced by the interconnecting lines (and are the subject of Chapter 4). A profound understanding of the nature and the behavior of these intrinsic capacitances is
essential for the designer of high-quality digital integrated circuits. They originate from
three sources: the basic MOS structure, the channel charge, and the depletion regions of
the reverse-biased pn-junctions of drain and source. Aside from the MOS structure capacitances, all capacitors are nonlinear and vary with the applied voltage, which makes their
analysis hard. We discuss each of the components in turn.
chapter3.fm Page 109 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
109
MOS Structure Capacitances
The gate of the MOS transistor is isolated from the conducting channel by the gate oxide
that has a capacitance per unit area equal to Cox = εox / tox. We learned earlier that from a IV perspective it is useful to have Cox as large as possible, or to keep the oxide thickness
very thin. The total value of this capacitance is called the gate capacitance Cg and can be
decomposed into two elements, each with a different behavior. Obviously, one part of Cg
contributes to the channel charge, and is discussed in a subsequent section. Another part is
solely due to the topological structure of the transistor. This component is the subject of
the remainder of this section.
Consider the transistor structure of Figure 3.28. Ideally, the source and drain diffusion should end right at the edge of the gate oxide. In reality, both source and drain tend to
extend somewhat below the oxide by an amount xd, called the lateral diffusion. Hence, the
effective channel of the transistor L becomes shorter than the drawn length Ld (or the
length the transistor was originally designed for) by a factor of ∆L = 2xd. It also gives rise
to a parasitic capacitance between gate and source (drain) that is called the overlap capacitance. This capacitance is strictly linear and has a fixed value
Polysilicon gate
Drain
Source
W
n+
xd
n+
xd
Ld
Gate-bulk
overlap
(a) Top view
Gate oxide
tox
n+
L
(b) Cross section
n+
Figure 3.28
MOSFET overlap capacitance.
C GSO = C GDO = C ox x d W = C o W
(3.45)
Since xd is a technology-determined parameter, it is customary to combine it with the
oxide capacitance to yield the overlap capacitance per unit transistor width Co (more specifically, Cgso and Cgdo).
Channel Capacitance
Perhaps the most significant MOS parasitic circuit element, the gate-to-channel capacitance CGC varies in both magnitude and in its division into three components CGCS, CGCD,
and CGCB (being the gate-to-source, gate-to-drain, and gate-to-body capacitances, respectively), depending upon the operation region and terminal voltages. This varying distribution is best explained with the simple diagrams of Figure 3.29. When the transistor is in
chapter3.fm Page 110 Friday, January 18, 2002 9:00 AM
THE DEVICES
110
Chapter 3
cut-off (a), no channel exists, and the total capacitance CGC appears between gate and
body. In the resistive region (b), an inversion layer is formed, which acts as a conductor
between source and drain. Consequently, CGCB = 0 as the body electrode is shielded from
the gate by the channel. Symmetry dictates that the capacitance distributes evenly between
source and drain. Finally, in the saturation mode (c), the channel is pinched off. The
capacitance between gate and drain is approximately zero, and so is the gate-body capacitance. All the capacitance hence is between gate and source.
G
CGC
CGC
CGC
D
S
G
G
D
S
(a) cut-off
D
S
(c) saturation
(b) resistive
Figure 3.29 The gate-to-channel capacitance and how the operation region influences is distribution over the three other
device terminals.
To actual value of the total gate-channel capacitance and its distribution over the
three components is best understood with the aid of a number of charts. The first plot (Figure 3.30a) captures the evolution of the capacitance as a function of VGS for VDS = 0. For
VGS = 0, the transistor is off, no channel is present and the total capacitance, equal to
WLCox, appears between gate and body. When increasing VGS, a depletion region forms
under the gate. This seemingly causes the thickness of the gate dielectric to increase,
which means a reduction in capacitance. Once the transistor turns on (VGS = VT), a channel
is formed and CGCB drops to 0. With VDS = 0, the device operates in the resistive mode and
the capacitance divides equally between source and drain, or CGCS = CGCD = WLCox/2. The
large fluctuation of the channel capacitance around VGS=VT is worth remembering. A
designer looking for a well-behaved linear capacitance should avoid operation in this
region.
CGC
WLCox
WLCox
CGCB
CGCS = CGCD
2
WLCox
CGC
Figure 3.30
3
WLCox
CGCD
2
VGS
VT
(a) CGC as a function of VGS (with VDS=0)
2WLCox
CGCS
0
VDS/(VGS-VT)
1
(b) CGC as a function of the degree of saturation
Distribution of the gate-channel capacitance as a function of VGS and VDS (from [Dally98]).
Once the transistor is on, the distribution of its gate capacitance depends upon the
degree of saturation, measured by the VDS/(VGS-VT) ratio. As illustrated in Figure 3.30b,
chapter3.fm Page 111 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
111
CGCD gradually drops to 0 for increasing levels of saturation, while CGCS increases to 2/3
CoxWL. This also means that the total gate capacitance is getting smaller with an increased
level of saturation.
From the above, it becomes clear that the gate-capacitance components are nonlinear and varying with the operating voltages. To make a first-order analysis possible, we
will use a simplified model with a constant capacitance value in each region of operation
in the remainder of the text. The assumed values are summarized in Table 3.4.
Table 3.4
Average distribution of channel capacitance of MOS transistor for different operation regions.
Operation Region
CGCB
CGCS
CGCD
CGC
CG
Cutoff
CoxWL
0
0
CoxWL
CoxWL+2CoW
Resistive
0
CoxWL / 2
CoxWL / 2
CoxWL
CoxWL+2CoW
Saturation
0
(2/3)CoxWL
0
(2/3)CoxWL
(2/3)CoxWL+2CoW
Example 3.9 Using a circuit simulator to extract capacitance
Determining the value of the parasitic capacitances of an MOS transistor for a given operation
mode is a labor-intensive task, and requires the knowledge of a number of technology parameters that are often not explicitly available. Fortunately, once a SPICE model of the transistor
is attained, a simple simulation can give you the data you are interested in. Assume we would
like to know the value of the total gate capacitance of a transistor in a given technology as a
function of VGS (for VDS = 0). A simulation of the circuit of Figure 3.31a will give us exactly
this information. In fact, the following relation is valid:
I = C G(V GS)
dV GS
dt
which can be rewritten to yield an expression for CG.
dV
C G(V GS) = I ⁄ GS
dt
A transient simulation gives us VGS as a function of time, which can be translated into
the capacitance with the aid of some simple mathematical manipulations. This is demonstrated in Figure 3.31b, which plots the simulated gate capacitance of a minimum size 0.25
µm NMOS transistor as a function of VGS. The graphs clearly shows the drop of the capacitance when VGS approaches VT and the discontinuity at VT, predicted in Figure 3.30.
Junction Capacitances
A final capacitive component is contributed by the reverse-biased source-body and drainbody pn-junctions. The depletion-region capacitance is nonlinear and decreases when the
reverse bias is raised as discussed earlier. To understand the components of the junction
capacitance (often called the diffusion capacitance), we must look at the source (drain)
chapter3.fm Page 112 Friday, January 18, 2002 9:00 AM
THE DEVICES
112
Chapter 3
-16
10
VGS
x 10
9
Gate Capacitance (F)
8
I
(a)
Figure 3.31 Simulating the gate capacitance of an MOS
transistor; (a) circuit configuration used for the analysis, (b)
resulting capacitance plot for minimum-size NMOS transistor
in 0.25 µm technology.
7
6
5
4
3
2
-2
-1.5
-1
-0.5
0
V
GS
0.5
1
1.5
2
(V)
(b)
region and its surroundings. The detailed picture, shown in Figure 3.32, shows that the
junction consists of two components:
Channel-stop implant
NA+
Side wall
Source
ND
W
Bottom
xj
Side wall
Channel
LS
Substrate NA
Figure 3.32
Detailed view of source junction.
• The bottom-plate junction, which is formed by the source region (with doping ND)
and the substrate with doping NA. The total depletion region capacitance for this
component equals Cbottom = CjWLS, with Cj the junction capacitance per unit area as
given by Eq. (3.9). As the bottom-plate junction is typically of the abrupt type, the
grading coefficient m approaches 0.5.
• The side-wall junction, formed by the source region with doping ND and the p+ channel-stop implant with doping level NA+. The doping level of the stopper is usually
larger than that of the substrate, resulting in a larger capacitance per unit area. The
side-wall junction is typically graded, and its grading coefficient varies from 0.33 to
0.5. Its capacitance value equals Csw = C'jswxj (W + 2 × Ls). Notice that no side-wall
capacitance is counted for the fourth side of the source region, as this represents the
conductive channel.4
Since xj, the junction depth, is a technology parameter, it is normally combined with
C'jsw into a capacitance per unit perimeter Cjsw = C'jswxj. An expression for the total
junction capacitance can then be derived,
chapter3.fm Page 113 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
113
C diff = C bottom + C sw = C j × AREA + Cjsw × PERIMETER
= C j L S W + C jsw ( 2L S + W )
(3.46)
Since all these capacitances are small-signal capacitances, we normally linearize them and
use average capacitances along the lines of Eq. (3.10).
Problem 3.1
Using a circuit simulator to determine the drain capacitance
Derive a simple circuit that would help you to derive the drain capacitance of an NMOS
transistor in the different operation modes using circuit simulation (in the style of Figure
3.31).
Capacitive Device Model
All the above contributions can be combined in a single capacitive model for the MOS
transistor, which is shown Figure 3.33. Its components are readily identified on the basis
of the preceding discussions.
G
CGS
CGD
D
S
CGB
CSB
CDB
Figure 3.33
MOSFET capacitance model.
B
CGS = CGCS + CGSO; CGD = CGCD + CGDO; CGB = CGCB
CSB = CSdiff; CDB = CDdiff
(3.47)
It is essential for the designers of high-performance and low-energy circuits to be very
familiar with this model as well as to have an intuitive feeling of the relative values of its
components.
Example 3.10
MOS Transistor Capacitances
Consider an NMOS transistor with the following parameters: tox = 6 nm, L = 0.24 µm, W =
0.36 µm, LD = LS = 0.625 µm, CO = 3 × 10–10 F/m, Cj0 = 2 × 10–3 F/m2, Cjsw0 = 2.75 × 10–10
F/m. Determine the zero-bias value of all relevant capacitances.
The gate capacitance per unit area is easily derived as (εox / tox) and equals 5.7 fF/µm2.
The gate-to-channel CGC then equals WLCox = 0.49 fF. To find the total gate capacitance, we
have to add the source and drain overlap capacitors, each of which equals WCO = 0.105 fF.
This leads to a total gate capacitance of 0.7 fF.
4
To be entirely correct, we should take the diffusion capacitance of the source(drain)-to-channel junction
into account. Due to the doping conditions and the small area, this component can virtually always be ignored in
a first-order analysis. Detailed SPICE models most often include a factor CJSWG to account for this junction.
chapter3.fm Page 114 Friday, January 18, 2002 9:00 AM
THE DEVICES
114
Chapter 3
The diffusion capacitance consists of the bottom and the side-wall capacitances. The
former is equal to Cj0 LDW = 0.45 fF, while the side-wall capacitance under zero-bias conditions evaluates to Cjsw0 (2LD + W) = 0.44 fF. This results in a total drain(source)-to-bulk
capacitance of 0.89 fF.
The diffusion capacitance seems to dominate the gate capacitance. This is a worst-case
condition, however. When increasing the value of the reverse bias over the junction — as is
the normal operation mode in MOS circuits —, the diffusion capacitance is substantially
reduced. Also, clever design can help to reduce the value of LD (LS). In general, it can be
stated that the contribution of diffusion capacitances is at most equal, and very often substantially smaller than the gate capacitance.
Design Data — MOS Transistor Capacitances
Table 3.5 summarizes the parameters needed to estimate the parasitic capacitances of the MOS
transistors in our generic 0.25 µm CMOS process.
Table 3.5 Capacitance parameters of NMOS and PMOS transistors in 0.25 µm CMOS process.
Cox
(fF/µm2)
CO
(fF/µm)
Cj
(fF/µm2)
mj
φb
(V)
Cjsw
(fF/µm)
mjsw
φbsw
(V)
NMOS
6
0.31
2
0.5
0.9
0.28
0.44
0.9
PMOS
6
0.27
1.9
0.48
0.9
0.22
0.32
0.9
Source-Drain Resistance
The performance of a CMOS circuit may further be affected by another set of parasitic
elements, being the resistances in series with the drain and source regions, as shown in
Figure 3.34a. This effect become more pronounced when transistors are scaled down, as
this leads to shallower junctions and smaller contact openings become smaller. The resistance of the drain (source) region can be expressed as
L S, D
R
R S, D = ---------W
+ RC
(3.48)
with RC the contact resistance, W the width of the transistor, and LS,D the length of the
source or drain region (Figure 3.34b). R❏ is the sheet resistance per square of the drainsource diffusion, and ranges from 20 to 100 Ω/ ❏. Observe that the resistance of a square
of material is constant, independent of its size (see also Chapter 4).
The series resistance causes a deterioration in the device performance, as it reduces
the drain current for a given control voltage. Keeping its value as small as possible is thus
an important design goal for both the device and the circuit engineer. One option, popular
in most contemporary processes, is to cover the drain and source regions with a low-resistivity material such as titanium or tungsten. This process is called silicidation and effec-
chapter3.fm Page 115 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
115
tively reduces the sheet resistance to values in the range from 1 to 4 Ω/❏.5 Making the
transistor wider than needed is another possibility as should be obvious from Eq. (3.48).
With a process that includes silicidation and proper attention to layout, parasitic resistance
is not important. However, the reader should be aware that careless layout may lead to
resistances that severely degrade the device performance.
3.3.4
The Actual MOS Transistor—Some Secondary Effects
The operation of a contemporary transistor may show some important deviations from the
model we have presented so far. These divergences become especially pronounced once
the dimensions of the transistor reach the deep sub-micron realm. At that point, the
assumption that the operation of a transistor is adequately described by a one-dimensional
model, where it is assumed that all current flows on the surface of the silicon and the electrical fields are oriented along that plane, is not longer valid. Two- or even three-dimensional models are more appropriate. An example of such was already given in Section
3.2.2 when we discussed the mobility degradation.
The understanding of some of these second-order effects and their impact on the
device behavior is essential in the design of today’s digital circuits and therefore merits
some discussion. One word of warning, though. Trying to take all those effects into
account in a manual, first-order analysis results in intractable and opaque circuit models. It
is therefore advisable to analyze and design MOS circuits first using the ideal model. The
impact of the non-idealities can be studied in a second round using computer-aided simulation tools with more precise transistor models.
Polysilicon gate
LD
G
Drain
contact
D
S
RS
W
VGS,eff
RD
Drain
(a) Modeling the series resistance
Figure 3.34
5
4.
(b) Parameters of the series resistance
Series drain and source resistance.
Silicidation is also used to reduce the resistance of the polysilicon gate, as will be discussed in Chapter
chapter3.fm Page 116 Friday, January 18, 2002 9:00 AM
THE DEVICES
116
Chapter 3
VT
VT
Long-channel threshold
L
(a) Threshold as a function of the
length (for low VDS)
Figure 3.35
Low VDS threshold
VDS
(b) Drain-induced barrier
lowering (for low L)
Threshold variations.
Threshold Variations
Eq. (3.19) states that the threshold voltage is only a function of the manufacturing technology and the applied body bias VSB. The threshold can therefore be considered as a constant
over all NMOS (PMOS) transistors in a design. As the device dimensions are reduced, this
model becomes inaccurate, and the threshold potential becomes a function of L, W, and
VDS. Two-dimensional second-order effects that were ignorable for long-channel devices
suddenly become significant.
In the traditional derivation of the VTO, for instance, it is assumed that the channel
depletion region is solely due to the applied gate voltage and that all depletion charge
beneath the gate originates from the MOS field effects. This ignores the depletion regions
of the source and reverse-biased drain junction, which become relatively more important
with shrinking channel lengths. Since a part of the region below the gate is already
depleted (by the source and drain fields), a smaller threshold voltage suffices to cause
strong inversion. In other words, VT0 decreases with L for short-channel devices (Figure
3.35a). A similar effect can be obtained by raising the drain-source (bulk) voltage, as this
increases the width of the drain-junction depletion region. Consequently, the threshold
decreases with increasing VDS. This effect, called the drain-induced barrier lowering, or
DIBL, causes the threshold potential to be a function of the operating voltages (Figure
3.35b). For high enough values of the drain voltage, the source and drain regions can even
be shorted together, and normal transistor operation ceases to exist. The sharp increase in
current that results from this effect, which is called punch-through, may cause permanent
damage to the device and should be avoided. Punch-through hence sets an upper bound on
the drain-source voltage of the transistor.
Since the majority of the transistors in a digital circuit are designed at the minimum
channel length, the variation of the threshold voltage as a function of the length is almost
uniform over the complete design, and is therefore not much of an issue except for the
increased sub-threshold leakage currents. More troublesome is the DIBL, as this effect
varies with the operating voltage. This is, for instance, a problem in dynamic memories,
where the leakage current of a cell (being the subthreshold current of the access transistor)
becomes a function of the voltage on the data-line, which depends upon the applied data
patterns. From the cell perspective, DIBL manifests itself as a data-dependent noise
source.
chapter3.fm Page 117 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
117
Worth mentioning is that the threshold of the MOS transistor is also subject to narrow-channel effects. The depletion region of the channel does not stop abruptly at the
edges of the transistor, but extends somewhat under the isolating field-oxide. The gate
voltage must support this extra depletion charge to establish a conducting channel. This
effect is ignorable for wide transistors, but becomes significant for small values of W,
where it results in an increase of the threshold voltage. For small geometry transistors,
with small values of L and W, the effects of short- and narrow channels may tend to cancel
each other out.
Hot-Carrier Effects
Besides varying over a design, threshold voltages in short-channel devices also have the
tendency to drift over time. This is the result of the hot-carrier effect [Hu92]. Over the last
decades, device dimensions have been scaled down continuously, while the power supply
and the operating voltages were kept constant. The resulting increase in the electrical field
strength causes an increasing velocity of the electrons, which can leave the silicon and
tunnel into the gate oxide upon reaching a high-enough energy level. Electrons trapped in
the oxide change the threshold voltage, typically increasing the thresholds of NMOS
devices, while decreasing the VT of PMOS transistors. For an electron to become hot, an
electrical field of at least 104 V/cm is necessary. This condition is easily met in devices
with channel lengths around or below 1 µm. The hot-electron phenomenon can lead to a
long-term reliability problem, where a circuit might degrade or fail after being in use for a
while. This is illustrated in Figure 3.36, which shows the degradation in the I-V characteristics of an NMOS transistor after it has been subjected to extensive operation. State-ofthe-art MOSFET technologies therefore use specially-engineered drain and source regions
to ensure that the peaks in the electrical fields are bounded, hence preventing carriers to
reach the critical values necessary to become hot. The reduced supply voltage that is typical for deep sub-micron technologies can in part be attributed to the necessity to keep hotcarrier effects under control.
Figure 3.36 Hot-carrier effects cause the I-V characteristics of an NMOS transistor to degrade from
extensive usage (from [McGaughy98]).
chapter3.fm Page 118 Friday, January 18, 2002 9:00 AM
THE DEVICES
118
Chapter 3
CMOS Latchup
The MOS technology contains a number of intrinsic bipolar transistors. These are especially troublesome in CMOS processes, where the combination of wells and substrates
results in the formation of parasitic n-p-n-p structures. Triggering these thyristor-like
devices leads to a shorting of the VDD and VSS lines, usually resulting in a destruction of
the chip, or at best a system failure that can only be resolved by power-down.
Consider the n-well structure of Figure 3.37a. The n-p-n-p structure is formed by the
source of the NMOS, the p-substrate, the n-well and the source of the PMOS. A circuit
equivalent is shown in Figure 3.37b. When one of the two bipolar transistors gets forward
biased (e.g., due to current flowing through the well, or substrate), it feeds the base of the
other transistor. This positive feedback increases the current until the circuit fails or
burns out.
VDD
VDD
Rnwell
+
n
p
+
n+
p
+
n-well
+
p
Rnwell
Rpsubs
n-source
p-substrate
(a) Origin of latchup
Figure 3.37
p-source
n+
Rpsubs
(b) Equivalent circuit
CMOS latchup.
From the above analysis the message to the designer is clear—to avoid latchup, the
resistances Rnwell and Rpsubs should be minimized. This can be achieved by providing
numerous well and substrate contacts, placed close to the source connections of the
NMOS/PMOS devices. Devices carrying a lot of current (such as transistors in the I/O
drivers) should be surrounded by guard rings. These circular well/substrate contacts, positioned around the transistor, reduce the resistance even further and reduce the gain of the
parasitic bipolars. For an extensive discussion on how to avoid latchup, please refer to
[Weste93]. The latchup effect was especially critical in early CMOS processes. In recent
years, process innovations and improved design techniques have all but eliminated the
risks for latchup.
3.3.5
SPICE Models for the MOS Transistor
The complexity of the behavior of the short-channel MOS transistor and its many parasitic
effects has led to the development of a wealth of models for varying degrees of accuracy
and computing efficiency. In general, more accuracy also means more complexity and,
hence, an increased run time. In this section, we briefly discuss the characteristics of the
chapter3.fm Page 119 Friday, January 18, 2002 9:00 AM
Section 3.3
The MOS(FET) Transistor
119
more popular MOSFET models, and describe how to instantiate a MOS transistor in a circuit description.
SPICE Models
SPICE has three built-in MOSFET models, selected by the LEVEL parameter in the
model card. Unfortunately, all these models have been rendered obsolete by the progression to short-channel devices. They should only be used for first-order analysis, and we
therefore limit ourselves to a short discussion of their main properties.
• The LEVEL 1 SPICE model implements the Shichman-Hodges model, which is
based on the square law long-channel expressions, derived earlier in this chapter. It
does not handle short-channel effects.
• The LEVEL 2 model is a geometry-based model, which uses detailed device physics
to define its equations. It handles effects such as velocity saturation, mobility degradation, and drain-induced barrier lowering. Unfortunately, including all 3D-effects
of an advanced submicron process in a pure physics-based model becomes complex
and inaccurate.
• LEVEL 3 is a semi-empirical model. It relies on a mixture of analytical and empirical expressions, and uses measured device data to determine its main parameters. It
works quite well for channel lengths down to 1 µm.
In response to the inadequacy of the built-in models, SPICE vendors and semi-conductor manufacturers have introduced a wide range of accurate, but proprietary models. A
complete description of all those would take the remainder of this book, which is, obviously, not the goal. We refer the interested reader to the extensive literature on this topic
[e.g. Vladimirescu93].
The BSIM3V3 SPICE Model
The confusing situation of having to use a different model for each manufacturer has fortunately been partially resolved by the adoption of the BSIM3v3 model as an industrywide standard for the modeling of deep-submicron MOSFET transistors. The Berkeley
Short-Channel IGFET Model (or BSIM in short) provides a model that is analytically
simple and is based on a ‘small’ number of parameters, which are normally extracted from
experimental data. Its popularity and accuracy make it the natural choice for all the simulations presented in this book.
A full-fledged BSIM3v3 model (denoted as LEVEL 49) contains over 200 parameters, the majority of which are related to the modeling of second-order effects. Fortunately, understanding the intricacies of all these parameters is not a requirement for the
digital designer. We therefore only present an overview of the parameter categories (Table
3.6). The Bin category deserves some extra attention. Providing a single set of parameters
that is acceptable over all possible device dimensions is deemed to be next to impossible.
So, a set of models is provided, each of which is valid for a limited region delineated by
chapter3.fm Page 120 Friday, January 18, 2002 9:00 AM
THE DEVICES
120
Chapter 3
LMIN, LMAX, WMIN, and WMAX (called a bin). It is typically left to the user to select
the correct bin for a particular transistor.
Table 3.6 BSIM3-V3 model parameter categories, and some important parameters.
Parameter Category
Description
Control
Selection of level and models for mobility, capacitance, and noise
LEVEL, MOBMOD, CAPMOD
DC
Parameters for threshold and current calculations
VTH0, K1, U0, VSAT, RSH,
AC & Capacitance
Parameters for capacitance computations
CGS(D)O, CJ, MJ, CJSW, MJSW
dW and dL
Derivation of effective channel length and width
Process
Process parameters such as oxide thickness and doping concentrations
TOX, XJ, GAMMA1, NCH, NSUB
Temperature
Nominal temperature and temperature coefficients for various device parameters
TNOM
Bin
Bounds on device dimensions for which model is valid
LMIN, LMAX, WMIN, WMAX
Flicker Noise
Noise model parameters
We refer the interested reader to the BSIM3v3 documentation provided on the website of the textbook (REFERENCE) for a complete description of the model parameters
and equations. The LEVEL-49 models for our generic 0.25 µm CMOS process can be
found at the same location.
Transistor Instantiation
The parameters that can be specified for an individual transistor are enumerated in
Table 3.7. Not all these parameters have to be defined for each transistor. SPICE assumes
default values (which are often zero!) for the missing factors.
WARNING: It is hard to expect accuracy from a simulator, when the circuit description
provided by the designer does not contain the necessary details. For instance, you must
accurately specify the area and the perimeter of the source and drain regions of the devices
when performing a performance analysis. Lacking this information, which is used for the
computation of the parasitic capacitances, your transient simulation will be next to useless. Similarly, it is often necessary to painstakingly define the value of the drain and
source resistance. The NRS and NRD values multiply the sheet resistance specified in the
transistor model for an accurate representation of the parasitic series source and drain
resistance of each transistor.
chapter3.fm Page 121 Friday, January 18, 2002 9:00 AM
Section 3.4
A Word on Process Variations
Table 3.7
121
SPICE transistor parameters.
Parameter Name
Symbol
SPICE Name
Units
Default Value
Drawn Length
L
L
m
−
Effective Width
W
W
m
−
2
0
Source Area
AREA
AS
m
Drain Area
AREA
AD
m2
0
Source Perimeter
PERIM
PS
m
0
Drain Perimeter
PERIM
PD
m
0
Squares of Source Diffusion
NRS
−
1
Squares of Drain Diffusion
NRD
−
1
Example 3.11
SPICE description of a CMOS inverter
An example of a SPICE description of a CMOS inverter, consisting of an NMOS and a
PMOS transistor, is given below. Transistor M1 is an NMOS device of model-type (and bin)
nmos.1 with its drain, gate, source, and body terminals connected to nodes nvout, nvin, 0, and
0, respectively. Its gate length is the minimum allowed in this technology (0.25 µm). The ‘+’
character at the start of line 2 indicates that this line is a continuation of the previous one.
The PMOS device of type pmos.1, connected between nodes nvout, nvin, nvdd, and
nvdd (D, G, S, and B, respectively), is three times wider, which reduces the series resistance,
but increases the parasitic diffusion capacitances as the area and perimeter of the drain and
source regions go up.
Finally, the .lib line refers to the file that contains the transistor models.
M1 nvout nvin 0 0 nmos.1 W=0.375U L=0.25U
+AD=0.24P PD=1.625U AS=0.24P PS=1.625U NRS=1 NRD=1
M2 nvout nvin nvdd nvdd pmos.1 W=1.125U L=0.25U
+AD=0.7P PD=2.375U AS=0.7P PS=2.375U NRS=0.33 NRD=0.33
.lib 'c:\Design\Models\cmos025.l'
3.4
A Word on Process Variations
The preceding discussions have assumed that a device is adequately modeled by a single
set of parameters. In reality, the parameters of a transistor vary from wafer to wafer, or
even between transistors on the same die, depending upon the position. This observed random distribution between supposedly identical devices is primarily the result of two factors:
1. Variations in the process parameters, such as impurity concentration densities, oxide
thicknesses, and diffusion depths, caused by nonuniform conditions during the deposition and/or the diffusion of the impurities. These result in diverging values for
sheet resistances, and transistor parameters such as the threshold voltage.
chapter3.fm Page 122 Friday, January 18, 2002 9:00 AM
THE DEVICES
122
Chapter 3
2. Variations in the dimensions of the devices, mainly resulting from the limited resolution of the photolithographic process. This causes deviations in the (W/L) ratios of
MOS transistors and the widths of interconnect wires.
Observe that quite a number of these deviations are totally uncorrelated. For instance,
variations in the length of an MOS transistor are unrelated to variations in the threshold
voltage as both are set by different process steps. Below we examine the impact on some
of the parameters that determine the transistor current.
• The threshold voltage VT can vary for numerous reasons: changes in oxide thickness, substrate, poly and implant impurity levels, and the surface charge. Accurate
control of the threshold voltage is an important goal for many reasons. Where in the
past thresholds could vary by as much as 50%, state-of-the-art digital processes
manage to control the thresholds to within 25-50 mV.
• k'n: The main cause for variations in the process transconductance is changes in
oxide thickness. Variations can also occur in the mobility but to a lesser degree.
• Variations in W and L. These are mainly caused by the lithographic process.
Observe that variations in W and L are totally uncorrelated since the first is determined in the field-oxide step, while the second is defined by the polysilicon definition and the source and drain diffusion processes.
The measurable impact of the process variations may be a substantial deviation of
the circuit behavior from the nominal or expected response, and this could be in either
positive or negative directions. This poses the designer for an important economic
dilemma. Assume, for instance, that you are supposed to design a microprocessor running
at a clock frequency of 500 MHz. It is economically important that the majority of the
manufactured dies meet that performance requirement. One way to achieve that goal is to
design the circuit assuming worst-case values for all possible device parameters. While
safe, this approach is prohibitively conservative and results in severely overdesigned and
hence uneconomical circuits.
To help the designer make a decision on how much margin to provide, the device
manufacturer commonly provides fast and slow device models in addition to the nominal
ones. These result in larger or smaller currents than expected, respectively.
Example 3.12
MOS Transistor Process Variations
To illustrate the possible impact of process variations on the performance of an MOS device,
consider a minimum-size NMOS device in our generic 0.25 µm CMOS process. A later chapter will establish that the speed of the device is proportional to the drain current that can be
delivered.
Assume initially that VGS = VDS = 2.5 V. From earlier simulations, we know that this
produces a drain current of 220 µA. The nominal model is now replaced by the fast and slow
models, that modify the length and width (±10%), threshold (±60 mV), and oxide thickness
(±5%) parameters of the device. Simulations produce the following data:
Fast: Id = 265 µA: +20%
Slow: Id = 182 µA: -17%
Let us now proceed one step further. The supply voltage delivered to a circuit is by no means
a constant either. For instance, the voltage delivered by a battery can drop off substantially
chapter3.fm Page 123 Friday, January 18, 2002 9:00 AM
Section 3.4
A Word on Process Variations
123
towards the end of its lifetime. In practice, a variation in 10% of the supply voltage may well
be expected.
Fast + Vdd = 2.75 V: Id = 302 µA: +37%
Slow + Vdd = 2.25 V: Id = 155 µA: -30%
The current levels and the associated circuit performance can thus vary by almost 100%
between the extreme cases. To guarantee that the fabricated circuits meet the performance
requirements under all circumstances, it is necessary to make the transistor 42%
(=220µA/155µA) wider then would be required in the nominal case. This translates into a
severe area penalty.
Fortunately, these worst- (or best-) case conditions occur only very rarely in reality.
The probability that all parameters assume their worst-case values simultaneously is very
low, and most designs will display a performance centered around the nominal design.
The art of the design for manufacturability is to center the nominal design so that the
majority of the fabricated circuits (e.g., 98%) will meet the performance specifications,
while keeping the area overhead minimal.
Specialized design tools to help meet this goal are available. For instance, the Monte
Carlo analysis approach [Jensen91] simulates a circuit over a wide range of randomly chosen values for the device parameters. The result is a distribution plot of design parameters
(such as the speed or the sensitivity to noise) that can help to determine if the nominal
design is economically viable. Examples of such distribution plots, showing the impact of
variations in the effective transistor channel length and the PMOS transistor thresholds on
the speed of an adder cell, are shown in Figure 3.38. As can be observed, technology variations can have a substantial impact on the performance parameters of a design.
2.10
2.10
Delay (ns)
Delay (ns)
1.90
1.70
1.50
1.10
1.90
1.70
1.20
1.30
1.40
1.50
Leff (in mm)
1.60
1.50
–0.90
–0.80
–0.70
–0.60
–0.50
VTp (V)
Figure 3.38 Distribution plots of speed of adder circuit as a function of varying device parameters, as obtained
by a Monte Carlo analysis. The circuit is implemented in a 2 µm (nominal) CMOS technology (courtesy of Eric
Boskin, UCB, and ATMEL corp.).
One important conclusion from the above discussion is that SPICE simulations
should be treated with care. The device parameters presented in a model represent average
values, measured over a batch of manufactured wafers. Actual implementations are bound
to differ from the simulation results, and for reasons other than imperfections in the mod-
chapter3.fm Page 124 Friday, January 18, 2002 9:00 AM
THE DEVICES
124
Chapter 3
eling approach. Be furthermore aware that temperature variations on the die can present
another source for parameter deviations. Optimizing an MOS circuit with SPICE to a resolution level of a picosecond or a microvolt is clearly a waste of effort.
3.5
Perspective: Technology Scaling
Over the last decades, we have observed a spectacular increase in integration density and
computational complexity of digital integrated circuits. As already argued in the introduction, applications that were considered implausible yesterday are already forgotten today.
Underlying this revolution are the advances in device manufacturing technology that
allow for a steady reduction of the minimum feature size such as the minimum transistor
channel length realizable on a chip. To illustrate this point, we have plotted in Figure 3.39
the evolution of the (average) minimum device dimensions starting from the 1960s and
projecting into the 21st century. We observe a reduction rate of approximately 13% per
year, halving every 5 years. Another interesting observation is that no real sign of a slowdown is in sight, and that the breathtaking pace will continue in the foreseeable future.
2
Minimum Feature Size (micron)
10
1
10
0
10
Figure 3.39 Evolution of (average) minimum channel
length of MOS transistors over time. Dots represent
observed or projected (2000 and beyond) values. The
continuous line represents a scaling scenario that
reduces the minimum feature with a factor 2 every 5
years.
-1
10
-2
10
1960
1970
1980
1990
2000
2010
Year
A pertinent question is how this continued reduction in feature size influences the
operating characteristics and properties of the MOS transistor, and indirectly the critical
digital design metrics such as switching frequency and power dissipation. A first-order
projection of this behavior is called a scaling analysis, and is the topic of this section. In
addition to the minimum device dimension, we have to consider the supply voltage as a
second independent variable in such a study. Different scaling scenarios result based on
how these two independent variables are varied with respect to each other [Dennard74,
Baccarani84].
Three different models are studied in Table 3.8. To make the results tractable, it is
assumed that all device dimensions scale by the same factor S (with S > 1 for a reduction
in size). This includes the width and length of the transistor, the oxide thickness, and the
junction depths. Similarly, we assume that all voltages, including the supply voltage and
chapter3.fm Page 125 Friday, January 18, 2002 9:00 AM
Section 3.5
Perspective: Technology Scaling
125
the threshold voltages, scale by a same ratio U. The relations governing the scaling behavior of the dependent variables are tabulated in column 2. Observe that this analysis only
considers short-channel devices with a linear dependence between control voltage and saturation current (as expressed by Eq. (3.39)). We discuss each scenario in turn.
Scaling scenarios for short-channel devices.
Table 3.8
Parameter
Relation
Full Scaling
General Scaling
Fixed-Voltage Scaling
W, L, tox
1/S
1/S
1/S
VDD, VT
1/S
1/U
1
NSUB
Area/Device
V/Wdepl
2
WL
2
S /U
S
1/S
S2
2
1/S
2
1/S2
Cox
1/tox
S
S
S
Cgate
CoxWL
1/S
1/S
1/S
kn, kp
CoxW/L
S
S
S
Isat
CoxWV
1/S
1/U
1
Current Density
Isat/Area
S
S2/U
S2
Ron
V/Isat
1
1
1
Intrinsic Delay
RonCgate
1/S
1/S
1/S
P
IsatV
1/S2
1/U2
Power Density
P/Area
1
2
S /U
2
1
S2
Full Scaling (Constant Electrical Field Scaling)
In this ideal model, voltages and dimensions are scaled by the same factor S. The goal is to
keep the electrical field patterns in the scaled device identical to those in the original
device. Keeping the electrical fields constant ensures the physical integrity of the device
and avoids breakdown or other secondary effects. This scaling leads to greater device density (Area), higher performance (Intrinsic Delay), and reduced power consumption (P).
The effects of full scaling on the device and circuit parameters are summarized in the third
column of Table 3.8. We use the intrinsic time constant, which is the product of the gate
capacitance and the on-resistance, as a measure for the performance. The analysis shows
that the on-resistance remains constant due to the simultaneous scaling of voltage swing
and current level. The performance improved is solely due to the reduced capacitance. The
results clearly demonstrate the beneficial effects of scaling—the speed of the circuit
increases in a linear fashion, while the power/gate scales down quadratically!6
6
Some assumptions were made when deriving this table:
1. It is assumed that the carrier mobilities are not affected by the scaling.
2. The substrate doping Nsub is scaled so that the maximum depletion-layer width is reduced by a
factor S.
3. It is furthermore assumed that the delay of the device is mainly determined by the intrinsic
capacitance (the gate capacitance) and that other device capacitances, such as the diffusion
capacitances, scale appropriately. This assumption is approximately true for the full-scaling
case, but not for fixed-voltage scaling, where Cdiff scales as 1 ⁄ S .
chapter3.fm Page 126 Friday, January 18, 2002 9:00 AM
THE DEVICES
126
Chapter 3
5
4.5
Supply Voltage (V)
4
3.5
3
2.5
2
1.5
1
0.5
10
0
10
-1
Minimum Feature Size (µ m)
Figure 3.40 Evolution of min and max supplyvoltage in digital integrated circuits as a function
of feature size. All values for 0.15 micron and
below are projected.
Fixed-Voltage Scaling
In reality, full scaling is not a feasible option. First of all, to keep new devices compatible
with existing components, voltages cannot be scaled arbitrarily. Having to provide for
multiple supply voltages adds considerably to the cost of a system. As a result, voltages
have not been scaled down along with feature sizes, and designers adhere to well-defined
standards for supply voltages and signal levels. As is illustrated in Figure 3.40, 5 V was
the de facto standard for all digital components up to the early 1990s, and a fixed-voltage
scaling model was followed.
Only with the introduction of the 0.5 µm CMOS technology did new standards such
as 3.3 V and 2.5 V make an inroad. Today, a closer tracking between voltage and device
dimension can be observed.The reason for this change in operation model can partially be
explained with the aid of the fixed-voltage scaling model, summarized in the fifth column
of Table 3.8. In a velocity-saturated device, keeping the voltage constant while scaling the
device dimensions does not give a performance advantage over the full-scaling model, but
instead comes with a major power penalty. The gain of an increased current is simply offset by the higher voltage level, and only hurts the power dissipation. This scenario is very
different from the situation that existed when transistors were operating in the long-channel mode, and the current was a quadratic function of the voltage (as per Eq. (3.29)).
Keeping the voltage constant under these circumstances gives a distinct performance
advantage, as it causes a net reduction in on-resistance.
While the above argumentation offers ample reason to scale the supply voltages
with the technology, other physical phenomena such as the hot-carrier effect and oxide
breakdown also contributed to making the fixed-voltage scaling model unsustainable.
Problem 3.2 Scaling of Long-channel Devices
Demonstrate that for a long-channel transistor, full-voltage scaling results in a reduction
of the intrinsic delay with a factor S2, while increasing the power dissipation/device by S.
chapter3.fm Page 127 Friday, January 18, 2002 9:00 AM
Section 3.5
Perspective: Technology Scaling
127
Reconstruct Table 3.8 assuming that the current is a quadratic function of the voltage (Eq.
(3.29)).
WARNING: The picture painted in the previous section represents a first-order model.
Increasing the supply voltage still offers somewhat of a performance benefit for shortchannel transistors. This is apparent in Figure 3.27 and Table 3.3, which show a reduction
of the equivalent on-resistance with increasing supply voltage — even for the high voltage
range. Yet, this effect, which is mostly due to the channel-length modulation, is secondary
and is far smaller than what would be obtained in case of long-channel devices.
The reader should keep this warning in the back of his mind throughout this scaling
study. The goal is to discover first-order trends. This implies ignoring second-order effects
such as mobility-degradation, series resistance, etc.
General Scaling
We observe in Figure 3.40 that the supply voltages, while moving downwards, are not
scaling as fast as the technology. For instance, for the technology scaling from 0.5 µm to
0.1 µm, the maximum supply-voltage only reduces from 5 V to 1.5 V. The obvious question is why not to stick to the full-scaling model, when keeping the voltage higher does not
yield any convincing benefits? This departure is motivated by the following argumentation:
• Some of the intrinsic device voltages such as the silicon bandgap and the built-in
junction potential, are material parameters and cannot be scaled.
• The scaling potential of the transistor threshold voltage is limited. Making the
threshold too low makes it difficult to turn off the device completely. This is aggravated by the large process variation of the value of the threshold, even on the same
wafer.
Therefore, a more general scaling model is needed, where dimensions and voltages
are scaled independently. This general scaling model is shown in the fourth column of
Table 3.8. Here, device dimensions are scaled by a factor S, while voltages are reduced by
a factor U. When the voltage is held constant, U = 1, and the scaling model reduces to the
fixed-voltage model. Note that the general-scaling model offers a performance scenario
identical to the full- and the fixed scaling, while its power dissipation lies between the two
models (for S > U > 1).
Verifying the Model
To summarize this discussion on scaling, we have combined in Table 3.9 the characteristics of some of the most recent CMOS processes and projections on some future ones.
Observe how the operating voltages are being continuously reduced with diminishing
device dimensions. As predicted by the scaling model, the maximum drive current
remains approximately constant. Maintaining this level of drive in the presence of a
chapter3.fm Page 128 Friday, January 18, 2002 9:00 AM
THE DEVICES
128
Chapter 3
reduced supply voltage requires an aggressive lowering of the threshold voltage, which
translates in a rapid increase of the sub-threshold leakage current.
Table 3.9
MOSFET technology projection for high performance logic (from [SIA01]).
Year of Introduction
2001
2003
2005
2007
2010
2013
2016
Drawn channel length (nm)
90
65
45
35
25
18
13
Physical channel length (nm)
65
45
32
25
18
13
9
Gate oxide (nm)
2.3
2.0
1.9
1.4
1.2
1.0
0.9
VDD (V)
1.2
1.0
0.9
0.7
0.6
0.5
0.4
NMOS IDsat (µA/µm)
900
900
900
900
1200
1500
1500
NMOS Ileak (µA/µm)
0.01
0.07
0.3
1
3
7
10
From the above, it is reasonable to conclude that both integration density and performance will continue to increase. The obvious question is for how long? Experimental 25
nm CMOS devices have proven to be operational in the laboratories and to display current
characteristics that are surprisingly close to present-day transistors. These transistors,
while working along similar concepts as the current MOS devices, look very different
from the structures we are familiar with, and require some substantial device engineering.
For instance, Figure 3.41 shows a potential transistor structure, the Berkeley FinFET dualgated transistor, which has proven to be operational up to very small channel lengths.
Source
Source
Buried Oxide
Gate
SiO2
Si
Drain
Figure 3.41 FinFET dual-gated transistor
with 25 nm channel length [Hu99].
Another option is the vertical transistor. Even while the addition of many metal layers has
turned the integrated circuit into a truly three-dimensional artifact, the transistor itself is
still mostly laid out in a horizontal plane. This forces the device designer to jointly optimize packing density and performance parameters. By rotating the device so that the drain
ends up on top, and the source at the bottom, these concerns are separated: packing density
still is dominated by horizontal dimensions, while performance issues are mostly determined by vertical spacings (Figure 3.42). Operational devices of this type have been fabricated with channel lengths substantially below 0.1 µm. [Eaglesham00].
Integrated circuits integrating more then one billion transistors clocked at speeds of
tens of GHz’s hence seem to be well under way. Whether this will actually happen is an
open question. Even though it might be technologically feasible, other parameters have an
equal impact on the feasibility of such an undertaking. A first doubt is if such a part can be
chapter3.fm Page 129 Friday, January 18, 2002 9:00 AM
Section 3.6
Summary
129
D rain
G a te
G a te
Source
Figure 3.42 Vertical transistor with dual gates. The photo on the right shows an enlarged view of the channel area.
manufactured in an economical way. Current semiconductor plants cost over $5 billion,
and this price is expected to rise substantially with smaller feature sizes. Design considerations also play a role. Power consumption of such a component might be prohibitive. The
growing role of interconnect parasitics might put an upper bound on performance. Finally,
system considerations might determine what level of integration is really desirable. All in
all, it is obvious that the design of semiconductor circuits still faces an exciting future.
3.6
Summary
In this chapter, we have presented a a comprehensive overview of the operation of the
MOSFET transistor, the semiconductor device at the core of virtually all contemporary
digital integrated circuits. Besides an intuitive understanding of its behavior, we have presented a variety of modeling approaches ranging from simple models, useful for a firstorder manual analysis of the circuit operation, to complex SPICE models. These models
will be used extensively in later chapters, where we look at the fundamental building
blocks of digital circuits. We started off with a short discussion of the semiconductor
diode, one of the most dominant parasitic circuit elements in CMOS designs.
• The static behavior of the junction diode is well described by the ideal diode equation that states that the current is an exponential function of the applied voltage bias.
• In reverse-biased mode, the depletion-region space charge of the diode can be modeled as a non-linear voltage-dependent capacitance. This is particularly important as
the omnipresent source-body and drain-body junctions of the MOS transistors all
operate in this mode. A linearized large-scale model for the depletion capacitance
was introduced for manual analysis.
• The MOS(FET) transistor is a voltage-controlled device, where the controlling gate
terminal is insulated from the conducting channel by a SiO2 capacitor. Based on the
value of the gate-source voltage with respect to a threshold voltage VT, three operation regions have been identified: cut-off, linear, and saturation. One of the most
enticing properties of the MOS transistor, which makes it particularly amenable to
digital design, is that it approximates a voltage-controlled switch: when the control
voltage is low, the switch is nonconducting (open); for a high control voltage, a con-
chapter3.fm Page 130 Friday, January 18, 2002 9:00 AM
THE DEVICES
130
Chapter 3
ducting channel is formed, and the switch can be considered closed. This two-state
operation matches the concepts of binary digital logic.
• The continuing reduction of the device dimensions to the submicron range has introduced some substantial deviations from the traditional long-channel MOS transistor
model. The most important one is the velocity saturation effect, which changes the
dependence of the transistor current with respect to the controlling voltage from
quadratic to linear. Models for this effect as well as other second-order parasitics
have been introduced. One particular effect that is gaining in importance is the subthreshold conduction, which causes devices to conduct current even when the control voltage drops below the threshold.
• The dynamic operation of the MOS transistor is dominated by the device capacitors.
The main contributors are the gate capacitance and the capacitance formed by the
depletion regions of the source and drain junctions. The minimization of these
capacitances is the prime requirement in high-performance MOS design.
• SPICE models and their parameters have been introduced for all devices. It was
observed that these models represent an average behavior and can vary over a single
wafer or die.
• The MOS transistor is expected to dominate the digital integrated circuit scene for
the next decade. Continued scaling will lead to device sizes of approximately 0.07
micron by the year 2010, and logic circuits integrating more than 1 billion transistors on a die.
3.7
To Probe Further
Semiconductor devices have been discussed in numerous books, reprint volumes, tutorials, and journal articles. The IEEE Journal on Electron Devices is the premier journal,
where most of the state-of-the-art devices and their modeling are discussed. Another valuable resource are the proceedings of the International Electron Devices Meeting (IEDM).
The books (such as [Streetman95] and [Pierret96]) and journal articles referenced below
contain excellent discussions of the semiconductor devices of interest or refer to specific
topics brought up in the course of this chapter.
REFERENCES
[Baccarani84] G. Baccarani, M. Wordeman, and R. Dennard, “Generalized Scaling Theory and Its
Application to 1/4 Micrometer MOSFET Design,” IEEE Trans. Electron Devices, ED-31(4):
p. 452, 1984.
[Banzhaf92] W. Bhanzhaf, Computer Aided Analysis Using PSPICE, 2nd ed., Prentice Hall, 1992.
[Dennard74] R. Dennard et al., “Design of Ion-Implanted MOSFETS with Very Small Physical
Dimensions,” IEEE Journal of Solid-State Circuits, SC-9, pp. 256–258, 1974.
chapter3.fm Page 131 Friday, January 18, 2002 9:00 AM
Section 3.7
To Probe Further
131
[Eaglesham99] D. Eaglesham, “0.18 µm CMOS and Beyond,”, Proceedings 1999 Design Automation Conference, pp. 703-708, June 1999.
[Howe97] R. Howe and S. Sodini, Microelectronics: An Integrated Approach, Prentice Hall, 1997.
[Hu92] C. Hu, “IC Reliability Simulation,” IEEE Journal of Solid State Circuits, vol. 27, no. 3, pp.
241–246, March 1992.
[Jensen91] G. Jensen et al., “Monte Carlo Simulation of Semiconductor Devices,” Computer Physics Communications, 67, pp. 1–61, August 1991.
[Ko89] P. Ko, “Approaches to Scaling,” in VLSI Electronics: Microstructure Science, vol. 18, chapter 1, pp. 1–37, Academic Press, 1989.
[Nagel75] L. Nagel, “SPICE2: a Computer Program to Simulate Semiconductor Circuits,” Memo
ERL-M520, Dept. Elect. and Computer Science, University of California at Berkeley, 1975.
[Pierret96] R. Pierret, Semiconductor Device Fundamentals, Addison-Wesley, 1996.
[SIA01] International Technology Roadmap for Semiconductors, http://www.sematech.org, 2001.
[Streetman95] B. Streetman, Solid State Electronic Devices, Prentice Hall, 1995.
[Thorpe92] T. Thorpe, Computerized Circuit Analysis with SPICE, John Wiley and Sons, 1992.
[Vladimirescu93] A. Vladimirescu, The SPICE Book, John Wiley and Sons, 1993.
[Weste93] N. Weste and K. Eshragian, Principles of CMOS VLSI Design: A Systems Perspective,
Addison-Wesley, 1993.
chapter3.fm Page 132 Friday, January 18, 2002 9:00 AM
132
THE DEVICES
Chapter 3
chapter4.fm Page 133 Friday, January 18, 2002 9:00 AM
CHAPTER
4
THE WIRE
Determining and quantifying interconnect parameters
n
Introducing circuit models for interconnect wires
n
Detailed wire models for SPICE
n
Technology scaling and its impact on interconnect
4.1
Introduction
4.2
A First Glance
4.3
Interconnect Parameters — Capacitance,
Resistance, and Inductance
4.4
4.3.1
Capacitance
4.3.2
Resistance
4.3.3
Inductance
4.4.5
4.5
4.6
The Transmission Line
SPICE Wire Models
4.5.1
Distributed rc Lines in SPICE
4.5.2
Transmission Line Models in SPICE
Perspective: A Look into the Future
Electrical Wire Models
4.4.1
The Ideal Wire
4.4.2
The Lumped Model
4.4.3
The Lumped RC model
4.4.4
The Distributed rc Line
133
chapter4.fm Page 134 Friday, January 18, 2002 9:00 AM
THE WIRE
134
4.1
Chapter 4
Introduction
Throughout most of the past history of integrated circuits, on-chip interconnect wires were
considered to be second class citizens that had only to be considered in special cases or
when performing high-precision analysis. With the introduction of deep-submicron semiconductor technologies, this picture is undergoing rapid changes. The parasitics effects
introduced by the wires display a scaling behavior that differs from the active devices such
as transistors, and tend to gain in importance as device dimensions are reduced and circuit
speed is increased. In fact, they start to dominate some of the relevant metrics of digital
integrated circuits such as speed, energy-consumption, and reliability. This situation is
aggravated by the fact that improvements in technology make the production of everlarger die sizes economically feasible, which results in an increase in the average length of
an interconnect wire and in the associated parasitic effects. A careful and in-depth analysis
of the role and the behavior of the interconnect wire in a semiconductor technology is
therefore not only desirable, but even essential.
4.2
A First Glance
The designer of an electronic circuit has multiple choices in realizing the interconnections
between the various devices that make up the circuit. State-of-the-art processes offer multiple layers of Aluminum, and at least one layer of polysilicon. Even the heavily doped n+
or p+ layers, typically used for the realization of source and drain regions, can be
employed for wiring purposes. These wires appear in the schematic diagrams of electronic
circuits as simple lines with no apparent impact on the circuit performance. In our discussion on the integrated-circuit manufacturing process, it became clear that this picture is
overly simplistic, and that the wiring of today’s integrated circuits forms a complex geometry that introduces capacitive, resistive, and inductive parasitics. All three have multiple
effects on the circuit behavior.
1. An increase in propagation delay, or, equivalently, a drop in performance.
2. An impact on the energy dissipation and the power distribution.
3. An introduction of extra noise sources, which affects the reliability of the circuit.
A designer can decide to play it safe and include all these parasitic effects in her analysis
and design optimization process. This conservative approach is non-constructive and even
unfeasible. First of all, a “complete” model is dauntingly complex and is only applicable
to very small topologies. It is hence totally useless for today’s integrated circuits with their
millions of circuit nodes. Furthermore, this approach has the disadvantage that the “forest
gets lost between the trees”. The circuit behavior at a given circuit node is only determined
by a few dominant parameters. Bringing all possible effects to bear, only obscures the picture and turns the optimization and design process a “trial-and-error” operation rather than
an enlightened and focused search.
To achieve the latter, it is important that the designer has a clear insight in the parasitic wiring effects, their relative importance, and their models. This is best illustrated with
the simple example, shown in Figure 4.1. Each wire in a bus network connects a transmit-
chapter4.fm Page 135 Friday, January 18, 2002 9:00 AM
Section 4.2
A First Glance
135
receivers
transmitters
schematics view
physical view
Figure 4.1 Schematic and physical views of wiring of bus-network. The latter shows only a limited area (as
indicated by the shadings in the schematics).
ter (or transmitters) to a set of receivers and is implemented as a link of wire segments of
various lengths and geometries. Assume that all segments are implemented on a single
interconnect layer, isolated from the silicon substrate and from each other by a layer of
dielectric material. Be aware that the reality may be far more complex.
A full-fledged circuit model, taking into account the parasitic capacitance, resistance, and the inductance of the interconnections, is shown in Figure 4.2a. Observe that
these extra circuit elements are not located in a single physical point, but are distributed
over the length of the wire. This is a necessity when the length of the wire becomes significantly larger than its width. Notice also that some parasitics are inter-wire, hence creating
coupling effects between the different bus-signals that were not present in the original
schematics.
Analyzing the behavior of this schematic, which only models a small part of the circuit, is slow and cumbersome. Fortunately, substantial simplifications can often be made,
some of which are enumerated below.
• Inductive effects can be ignored if the resistance of the wire is substantial — this is
for instance the case for long Aluminum wires with a small cross-section — or if the
rise and fall times of the applied signals are slow.
• When the wires are short, the cross-section of the wire is large, or the interconnect
material used has a low resistivity, a capacitance-only model can be used (Figure
4.2b).
• Finally, when the separation between neighboring wires is large, or when the wires
only run together for a short distance, inter-wire capacitance can be ignored, and all
the parasitic capacitance can be modeled as capacitance to ground.
Obviously, the latter problems are the easiest to model, analyze, and optimize. The
experienced designer knows to differentiate between dominant and secondary effects. The
goal of this chapter is to present the reader the basic techniques to estimate the values of
chapter4.fm Page 136 Friday, January 18, 2002 9:00 AM
THE WIRE
136
(a)
Chapter 4
(b)
Figure 4.2 Wire models for the circuit of Figure 4.1. Model (a) considers most of the wire parasitics (with
the exception of inter-wire resistance and mutual inductance), while model (b) only considers capacitance.
the various interconnect parameters, simple models to evaluate their impact, and a set of
rules-of-thumb to decide when and where a particular model or effect should be considered.
4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
4.3.1
Capacitance
An accurate modeling of the wire capacitance(s) in a state-of-the-art integrated circuit is a
non-trivial task and is even today the subject of advanced research. The task is complicated by the fact that the interconnect structure of contemporary integrated circuits is
three-dimensional, as was clearly demonstrated in the process cross-section of Figure 2.8.
The capacitance of such a wire is a function of its shape, its environment, its distance to
the substrate, and the distance to surrounding wires. Rather than getting lost in complex
equations and models, a designer typically will use an advanced extraction tool to get precise values of the interconnect capacitances of a completed layout. Most semiconductor
manufacturers also provide empirical data for the various capacitance contributions, as
measured from a number of test dies. Yet, some simple first-order models come in handy
to provide a basic understanding of the nature of interconnect capacitance and its parameters, and of how wire capacitance will evolve with future technologies.
Consider first a simple rectangular wire placed above the semiconductor substrate,
as shown in Figure 4.3. If the width of the wire is substantially larger than the thickness of
the insulating material, it may be assumed that the electrical-field lines are orthogonal to
the capacitor plates, and that its capacitance can be modeled by the parallel-plate capaci-
chapter4.fm Page 137 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
137
tor model (also called area capacitance). Under those circumstances, the total capacitance
of the wire can be approximated as1
ε di
c int = ----- WL
t di
(4.1)
where W and L are respectively the width and length of the wire, and tdi and εdi represent
the thickness of the dielectric layer and its permittivity. SiO2 is the dielectric material of
choice in integrated circuits, although some materials with lower permittivity, and hence
lower capacitance, are coming in use. Examples of the latter are organic polyimides and
aerogels. ε is typically expressed as the product of two terms, or ε = εrε0. ε0 = 8.854 × 1012
F/m is the permittivity of free space, and εr the relative permittivity of the insulating
material. Table 4.1 presents the relative permittivity of several dielectrics used in integrated circuits. In summary, the important message from Eq. (4.1) is that the capacitance
is proportional to the overlap between the conductors and inversely proportional to their
separation.
Table 4.1
Relative permittivity of some typical dielectric materials.
εr
Material
Free space
1
Aerogels
~1.5
Polyimides (organic)
3-4
Silicon dioxide
3.9
Glass-epoxy (PC board)
5
Silicon Nitride (Si3N4)
7.5
Alumina (package)
9.5
Silicon
11.7
Current flow
L
Electrical-field lines
W
H
tdi
Dielectric
Substrate
Figure 4.3 Parallel-plate capacitance
model of interconnect wire.
1
To differentiate between distributed (per unit length) wire parameters versus total lumped values, we
will use lowercase to denote the former and uppercase for the latter.
chapter4.fm Page 138 Friday, January 18, 2002 9:00 AM
THE WIRE
138
Chapter 4
In actuality, this model is too simplistic. To minimize the resistance of the wires
while scaling technology, it is desirable to keep the cross-section of the wire (W×H) as
large as possible — as will become apparent in a later section. On the other hand, small
values of W lead to denser wiring and less area overhead. As a result, we have over the
years witnessed a steady reduction in the W/H-ratio, such that it has even dropped below
unity in advanced processes. This is clearly visible on the process cross-section of FIGURE. Under those circumstances, the parallel-plate model assumed above becomes inaccurate. The capacitance between the side-walls of the wires and the substrate, called the
fringing capacitance, can no longer be ignored and contributes to the overall capacitance.
This effect is illustrated in Figure 4.4a. Presenting an exact model for this difficult geome-
cfringe
(a) Fringing fields
cpp
w
H
+
Figure 4.4 The fringing-field
capacitance. The model decomposes
the capacitance into two contributions:
a parallel-plate capacitance, and a
fringing capacitance, modeled by a
cylindrical wire with a diameter equal to
the thickness of the wire.
(b) Model of fringing-field capacitance.
try is hard. So, as good engineering practice dictates, we will use a simplified model that
approximates the capacitance as the sum of two components (Figure 4.4b): a parallel-plate
capacitance determined by the orthogonal field between a wire of width w and the ground
plane, in parallel with the fringing capacitance modeled by a cylindrical wire with a
dimension equal to the interconnect thickness H. The resulting approximation is simple
and works fairly well in practice.
2πε di
wε di
+ -------------------------c wire = c pp + c fringe = ---------t di
log ( t di ⁄ H )
(4.2)
with w = W - H/2 a good approximation for the width of the parallel-plate capacitor.
Numerous more accurate models (e.g. [Vdmeijs84]) have been developed over time, but
these tend to be substantially more complex, and defeat our goal of developing a conceptual understanding.
To illustrate the importance of the fringing-field component, Figure 4.5 plots the
value of the wiring capacitance as a function of (W/H). For larger values of (W/H) the total
capacitance approaches the parallel-plate model. For (W/H) smaller than 1.5, the fringing
chapter4.fm Page 139 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
139
Capacitance (pF/cm)
component actually becomes the dominant component. The fringing capacitance can
increase the overall capacitance by a factor of more than 10 for small line widths. It is
interesting to observe that the total capacitance levels off to a constant value of approximately 1 pF/cm for line widths smaller than the insulator thickness. In other words, the
capacitance is no longer a function of the width.
H/tdi = 1
H/tdi = 0.5
Cp-p
W/Tdi
Figure 4.5 Capacitance of interconnect wire as a function of (W/tdi), including fringing-field effects
(from [Schaper83]). Two values of H/tdi are considered. Silicon-dioxide with εr = 3.9 is used as
dielectric.
So far, we have restricted our analysis to the case of a single rectangular conductor
placed over a ground plane. This structure, called a microstripline, used to be a good
model for semiconductor interconnections when the number of interconnect layers was
restricted to 1 or 2. Today’s processes offer many more layers of interconnect, which are
packed quite densely in addition. In this scenario, the assumption that a wire is completely
isolated from its surrounding structures and is only capacitively coupled to ground,
becomes untenable. This is illustrated in Figure 4.6, where the capacitance components of
a wire embedded in an interconnect hierarchy are identified. Each wire is not only coupled
to the grounded substrate, but also to the neighboring wires on the same layer and on adjacent layers. To a first order, this does not change the total capacitance connected to a given
wire. The main difference is that not all its capacitive components do terminate at the
grounded substrate, but that a large number of them connect to other wires, which have
dynamically varying voltage levels. We will later see that these floating capacitors form
not only a source of noise (crosstalk), but also can have a negative impact on the performance of the circuit.
In summary, inter-wire capacitances become a dominant factor in multi-layer interconnect structures. This effect is more outspoken for wires in the higher interconnect layers, as these wires are farther away from the substrate. The increasing contribution of the
inter-wire capacitance to the total capacitance with decreasing feature sizes is best illustrated by Figure 4.7. In this graph, which plots the capacitive components of a set of parallel wires routed above a ground plane, it is assumed that dielectric and wire thickness are
chapter4.fm Page 140 Friday, January 18, 2002 9:00 AM
THE WIRE
140
fringing
Chapter 4
parallel
Figure 4.6 Capacitive coupling
between wires in interconnect
hierarchy.
held constant while scaling all other dimensions. When W becomes smaller than 1.75 H,
the inter-wire capacitance starts to dominate.
Figure 4.7 Interconnect capacitance as
a function of design rules. It consists of a
capacitance to ground and an inter-wire
capacitance (from [Schaper83]).
sign Data
Interconnect Capacitance Design Data
A set of typical interconnect capacitances for a standard 0.25 µm CMOS process are given in
Table 4.2. The process supports 1 layer of polysilicon and 5 layers of Aluminum. Metal layers
1 to 4 have the same thickness and use a similar dielectric, while the wires at metal layer 5 are
almost twice as thick and are embedded in a dielectric with a higher permittivity. When placing
the wires over the thick field oxide that is used to isolate different transistors, use the “Field”
column in the table, while wires routed over the active area see a higher capacitance as seen in
the “Active” column. Be aware that the presented values are only indicative. To obtain more
chapter4.fm Page 141 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
141
accurate results for actual structures, complex 3-dimensional models should be used that take
the environment of the wire into account.
Wire area and fringe capacitance values for typical 0.25 µm CMOS process. The
table rows represent the top plate of the capacitor, the columns the bottom plate. The
area capacitances are expressed in aF/µm2, while the fringe capacitances (given in the
shaded rows) are in aF/µm.
Table 4.2
Field
Active
Poly
41
57
Al1
Al2
Al3
Al4
88
Poly
54
30
Al1
40
47
54
Al2
13
15
17
25
27
29
45
Al3
8.9
9.4
10
15
18
19
20
27
49
Al4
6.5
6.8
7
8.9
15
14
15
15
18
27
45
Al5
5.2
5.4
5.4
6.6
9.1
14
38
12
12
12
14
19
27
52
36
41
35
Table 4.3 tabulates indicative values for the capacitances between parallel wires placed
on the same layer with a minimum spacing (as dictated by the design rules). Observe that these
numbers include both the parallel plate and fringing components. Once again, the capacitances
are a strong function of the topology. For instance, a ground plane placed on a neighboring
layer terminates a large fraction of the fringing field, and effectively reduces the inter-wire
capacitance. The polysilicon wires experience a reduced inter-wire capacitance due to the
smaller thickness of the wires. On the other hand, the thick Al5 wires display the highest interwire capacitance. It is therefore advisable to either separate wires at this level by an amount
that is larger than the minimum allowed, or to use it for global signals that are not that sensitive
to interference. The supply rails are an example of the latter.
Table 4.3 inter-wire capacitance per unit wire length for different interconnect layers of typical 0.25
µm CMOS process. The capacitances are expressed in aF/µm, and are for minimally-spaced wires.
Layer
Poly
Al1
Al2
Al3
Al4
Al5
Capacitance
40
95
85
85
85
115
chapter4.fm Page 142 Friday, January 18, 2002 9:00 AM
THE WIRE
142
Chapter 4
Example 4.1 Capacitance of Metal Wire
Some global signals, such as clocks, are distributed all over the chip. The length of those
wires can be substantial. For die sizes between 1 and 2 cm, wires can reach a length of 10 cm
and have associated wire capacitances of substantial value. Consider an aluminum wire of 10
cm long and 1 µm wide, routed on the first Aluminum layer. We can compute the value of the
total capacitance using the data presented in Table 4.2.
Area (parallel-plate) capacitance: (0.1 × 106 µm2) × 30 aF/µm2= 3 pF
Fringing capacitance: 2 × (0.1 × 106 µm) × 40 aF/µm = 8 pF
Total capacitance: 11 pF
Notice the factor 2 in the computation of the fringing capacitance, which takes the two sides
of the wire into account.
Suppose now that a second wire is routed alongside the first one, separated by only the
minimum allowed distance. From Table 4.3, we can determine that this wire will couple to
the first with a capacitance equal to
Cinter =(0.1 × 106 µm) × 95 aF/µm = 9.5 pF
which is almost as large as the total capacitance to ground!
A similar exercise shows that moving the wire to Al4 would reduce the capacitance to
ground to 3.45 pF (0.65 pF area and 2.8 pF fringe), while the inter-wire capacitance would
remain approximately the same at 8.5 pF.
4.3.2
Resistance
The resistance of a wire is proportional to its length L and inversely proportional to its
cross-section A. The resistance of a rectangular conductor in the style of Figure 4.3 can be
expressed as
ρL
ρL
R = ------ = --------A
HW
(4.3)
where the constant ρ is the resistivity of the material (in Ω-m). The resistivities of some
commonly-used conductive materials are tabulated in Table 4.4. Aluminum is the interconnect material most often used in integrated circuits because of its low cost and its compatibility with the standard integrated-circuit fabrication process. Unfortunately, it has a
large resistivity compared to materials such as Copper. With ever-increasing performance
targets, this is rapidly becoming a liability and top-of-the-line processes are now increasingly using Copper as the conductor of choice.
Table 4.4
Resistivity of commonly-used conductors (at 20 C).
Material
ρ (Ω-m)
Silver (Ag)
1.6 × 10−8
chapter4.fm Page 143 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
Table 4.4
143
Resistivity of commonly-used conductors (at 20 C).
Material
ρ (Ω-m)
Copper (Cu)
1.7 × 10−8
Gold (Au)
2.2 × 10−8
Aluminum (Al)
2.7 × 10−8
Tungsten (W)
5.5 × 10−8
Since H is a constant for a given technology, Eq. (4.3) can be rewritten as follows,
LR = R❑ ---W
(4.4)
ρ
R❑ = ---H
(4.5)
with
the sheet resistance of the material, having units of Ω/❑ (pronounced as Ohm-per-square).
This expresses that the resistance of a square conductor is independent of its absolute size,
as is apparent from Eq. (4.4). To obtain the resistance of a wire, simply multiply the sheet
resistance by its ratio (L/W).
Interconnect Resistance Design Data
Typical values of the sheet resistance of various interconnect materials are given in Table 4.5.
Table 4.5
Sheet resistance values for a typical 0.25 µm CMOS process.
Material
Sheet Resistance (Ω/❑)
n- or p-well diffusion
1000 – 1500
+
+
n , p diffusion
50 – 150
n+, p+ diffusion with silicide
3–5
+
+
n , p polysilicon
150 – 200
n+, p+ polysilicon with silicide
4–5
Aluminum
0.05 – 0.1
From this table, we conclude that Aluminum is the preferred material for the wiring of
long interconnections. Polysilicon should only be used for local interconnect. Although the
sheet resistance of the diffusion layer (n+, p+) is comparable to that of polysilicon, the use of diffusion wires should be avoided due to its large capacitance and the associated RC delay.
chapter4.fm Page 144 Friday, January 18, 2002 9:00 AM
THE WIRE
144
Chapter 4
Advanced processes also offer silicided polysilicon and diffusion layers. A silicide is
a compound material formed using silicon and a refractory metal. This creates a highly
conductive material that can withstand high-temperature process steps without melting.
Examples of silicides are WSi2, TiSi2, PtSi2, and TaSi. WSi2, for instance, has a resistivity
ρ of 130 µΩ-cm, which is approximately eight times lower than polysilicon. The silicides
are most often used in a configuration called a polycide, which is a simple layered combination of polysilicon and a silicide. A typical polycide consists of a lower level of polysilicon with an upper coating of silicide and combines the best properties of both
materials—good adherence and coverage (from the poly) and high conductance (from the
silicide). A MOSFET fabricated with a polycide gate is shown in Figure 4.8. The advantage of the silicided gate is a reduced gate resistance. Similarly, silicided source and drain
regions reduce the source and drain resistance of the device.
Silicide
Polysilicon
SiO2
n+
n+
p
Figure 4.8
MOSFET.
A polycide-gate
Transitions between routing layers add extra resistance to a wire, called the contact
resistance. The preferred routing strategy is thus to keep signal wires on a single layer
whenever possible and to avoid excess contacts or via’s. It is possible to reduce the contact
resistance by making the contact holes larger. Unfortunately, current tends to concentrate
around the perimeter in a larger contact hole. This effect, called current crowding, puts a
practical upper limit on the size of the contact. The following contact resistances (for minimum-size contacts) are typical for a 0.25 µm process: 5-20 Ω for metal or polysilicon to
n+, p+, and metal to polysilicon; 1-5 Ω for via’s (metal-to-metal contacts).
Example 4.2 Resistance of a Metal Wire
Consider again the aluminum wire of Example 4.2, which is 10 cm long and 1 µm wide, and
is routed on the first Aluminum layer. Assuming a sheet resistance for Al1 of 0.075 Ω/❑, we
can compute the total resistance of the wire
Rwire = 0.075 Ω/❑ × (0.1 × 106 µm) / (1 µm)= 7.5 kΩ
Implementing the wire in polysilicon with a sheet resistance of 175 Ω/❑ raises the overall
resistance to 17.5 MΩ, which is clearly unacceptable. Silicided polysilicon with a sheet resistance of 4 Ω/❑ offers a better alternative, but still translates into a wire with a 400 kΩ resistance.
So far, we have considered the resistance of a semiconductor wire to be linear and
constant. This is definitely the case for most semiconductor circuits. At very high frequencies however, an additional phenomenon — called the skin effect — comes into play such
that the resistance becomes frequency-dependent. High-frequency currents tend to flow
primarily on the surface of a conductor with the current density falling off exponentially
chapter4.fm Page 145 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
145
with depth into the conductor. The skin depth δ is defined as the depth where the current
falls off to a value of e-1 of its nominal value, and is given by
δ =
ρ-------πfµ
(4.6)
with f the frequency of the signal and µ the permeability of the surrounding dielectric (typically equal to the permeability of free space, or µ = 4π × 10-7 H/m). For Aluminum at 1
GHz, the skin depth is equal to 2.6 µm. The obvious question is now if this is something
we should be concerned about when designing state-of-the-art digital circuits?
The effect can be approximated by assuming that the current flows uniformly in an
outer shell of the conductor with thickness δ, as is illustrated in Figure 4.9 for a rectangular wire. Assuming that the overall cross-section of the wire is now limited to approxiδ
H
W
Figure 4.9 The skin-effect reduces the flow of the current
to the surface of the wire.
mately 2(W+H)δ, we obtain the following expression for the resistance (per unit length) at
high frequencies (f > fs):
πfµρ
r ( f ) = ----------------------2(H + W)
(4.7)
The increased resistance at higher frequencies may cause an extra attenuation — and
hence distortion — of the signal being transmitted over the wire. To determine the on-set
of the skin-effect, we can find the frequency fs where the skin depth is equal to half the
largest dimension (W or H) of the conductor. Below fs the whole wire is conducting current, and the resistance is equal to (constant) low-frequency resistance of the wire. From
Eq. (4.6), we find the value of fs:
4ρ
f s = ---------------------------------------2
πµ ( max(W, H) )
(4.8)
Example 4.3 Skin-effect and Aluminum wires
We determine the impact of the skin-effect on contemporary integrated circuits by analyzing an Aluminum wire with a resistivity of 2.7×10-8 Ω-m, embedded in a SiO2 dielectric
with a permeability of 4π × 10-7 H/m. From Eq. (4.8), we find that the largest dimension of
wire should be at least 5.2 µm for the effect to be noticeable at 1 GHz. This is confirmed
by the more accurate simulation results of Figure 4.10, which plots the increase in resistance due to skin effects for different width Aluminum conductors. A 30% increase in
chapter4.fm Page 146 Friday, January 18, 2002 9:00 AM
THE WIRE
146
Chapter 4
resistance can be observed at 1 GHz for a 20 µm wire, while the increase for a 1 µm wire
is less than 1%.
Figure 4.10 Skin-effect
induced increase in resistance
as a function of frequency and
wire width. All simulations were
performed for a wire thickness
of 0.7 µm [Sylvester97].
In summary, the skin-effect is only an issue for wider wires. Since clocks tend to
carry the highest-frequency signals on a chip and also are fairly wide to limit resistance,
the skin effect is likely to have its first impact on these lines. This is a real concern for
GHz-range design, as clocks determine the overall performance of the chip (cycle time,
instructions per second, etc.). Another major design concern is that the adoption of better
conductors such as Copper may move the on-set of skin-effects to lower frequencies.
4.3.3
Inductance
Integrated-circuit designers tend to dismiss inductance as something they heard about in
their physics classes, but that has no impact on their field. This was definitely the case in
the first decades of integrated digital circuit design. Yet with the adoption of low-resistive
interconnect materials and the increase of switching frequencies to the super GHz range,
inductance starts to play a role even on a chip. Consequences of on-chip inductance
include ringing and overshoot effects, reflections of signals due to impedance mismatch,
inductive coupling between lines, and switching noise due to Ldi/dt voltage drops.
The inductance of a section of a circuit can always be evaluated with the aid of its
definition, which states that a changing current passing through an inductor generates a
voltage drop ∆V
∆V = L
di
dt
(4.9)
chapter4.fm Page 147 Friday, January 18, 2002 9:00 AM
Section 4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
147
It is possible to compute the inductance a wire directly from its geometry and its
environment. A simpler approach relies on the fact that the capacitance c and the inductance l (per unit length) of a wire are related by the following expression
cl = εµ
(4.10)
with ε and µ respectively the permittivity and permeability of the surrounding dielectric.
The caveat is that for this expression to be valid the conductor must be completely surrounded by a uniform dielectric medium. This is most often not the case. Yet even when
the wire is embedded in different dielectric materials, its is possible to adopt “average”
dielectric constants such that Eq. (4.10) still can be used to get an approximative value of
the inductance.
Some other interesting relations, obtained from Maxwell’s laws, can be pointed out.
The constant product of permeability and permittivity also defines the speed ν at which an
electromagnetic wave can propagate through the medium
c0
1
1
ν = -------- = ---------- = ------------lc
εr µr
εµ
(4.11)
c0 equals the speed of light (30 cm/nsec) in a vacuum. The propagation speeds for a number of materials used in the fabrication of electronic circuits are tabulated in Table 4.6.
The propagation speed for SiO2 is two times slower than in a vacuum.
Table 4.6 Dielectric constants and wave-propagation speeds for various materials used in electronic
circuits. The relative permeability µr of most dielectrics is approximately equal to 1.
εr
Propagation speed
(cm/nsec)
Vacuum
1
30
SiO2
3.9
15
Dielectric
PC board (epoxy glass)
5.0
13
Alumina (ceramic package)
9.5
10
Example 4.4 Inductance of a Semiconductor Wire
Consider an Al1 wire implemented in the 0.25 micron CMOS technology and routed on top
of the field oxide. From Table 4.2, we can derive the capacitance of the wire per unit length:
c = (W×30 + 2×40) aF/µm
From Eq. (4.10), we can derive the inductance per unit length of the wire, assuming
SiO2 as the dielectric and assuming a uniform dielectric (make sure to use the correct units!)
l = (3.9 × 8.854 × 10−12) × (4 π 10−7) / C
For wire widths of 0.4 µm, 1µm and 10µm, this leads to the following numbers:
chapter4.fm Page 148 Friday, January 18, 2002 9:00 AM
THE WIRE
148
Chapter 4
W = 0.4 µm: c = 92 aF/µm; l = 0.47 pH/µm
W = 1 µm: c = 110 aF/µm; l = 0.39 pH/µm
W = 10 µm: c = 380 aF/µm; l = 0.11 pH/µm
Assuming a sheet resistance of 0.075 Ω/❑, we can also determine the resistance of the
wire,
r = 0.075/W Ω/µm
It is interesting to observe that the inductive part of the wire impedance becomes equal
in value to the resistive component at a frequency of 27.5 GHz (for a 1 µm wide wire), as can
be obtained from solving the following expression:
ωl = 2πfl = r
For extra wide wires, this frequency reduces to approximately 11 GHz. For wires with
a smaller capacitance and resistance (such as the thicker wires located at the upper interconnect layers), this frequency can become as low as 500 MHz, especially when better interconnect materials such as Copper are being used. Yet, these numbers indicate that inductance
only becomes an issue in integrated circuits for frequencies that are well above 1 GHz.
4.4
Electrical Wire Models
In previous sections, we have introduced the electrical properties of the interconnect wire
— capacitance, resistance, and inductance — and presented some simple relations and
techniques to derive their values from the interconnect geometries and topologies. These
parasitic elements have an impact on the electrical behavior of the circuit and influence its
delay, power dissipation, and reliability. To study these effects requires the introduction of
electrical models that estimate and approximate the real behavior of the wire as a function
of its parameters. These models vary from very simple to very complex depending upon
the effects that are being studied and the required accuracy. In this section, we first derive
models for manual analysis, while how to cope with interconnect wires in the SPICE circuit simulator is the topic follows next.
4.4.1
The Ideal Wire
In schematics, wires occur as simple lines with no attached parameters or parasitics. These
wires have no impact on the electrical behavior of the circuit. A voltage change at one end
of the wire propagates immediately to its other ends, even if those are some distance away.
Hence, it may be assumed that the same voltage is present at every segment of the wire at
the every point in time, and that the whole wire is an equipotential region. While this
ideal-wire model is simplistic, it has its value, especially in the early phases of the design
process when the designer wants to concentrate on the properties and the behavior of the
transistors that are being connected. Also, when studying small circuit components such
as gates, the wires tend to be very short and their parasitics ignorable. Taking these into
account would just make the analysis unnecessarily complex. More often though, wire
parasitics play a role and more complex models should be considered.
chapter4.fm Page 149 Friday, January 18, 2002 9:00 AM
Section 4.4
4.4.2
Electrical Wire Models
149
The Lumped Model
The circuit parasitics of a wire are distributed along its length and are not lumped into a
single position. Yet, when only a single parasitic component is dominant, when the interaction between the components is small, or when looking at only one aspect of the circuit
behavior, it is often useful to lump the different fractions into a single circuit element. The
advantage of this approach is that the effects of the parasitic then can be described by an
ordinary differential equation. As we will see later, the description of a distributed element
requires partial differential equations.
As long as the resistive component of the wire is small and the switching frequencies are in the low to medium range, it is meaningful to consider only the capacitive component of the wire, and to lump the distributed capacitance into a single capacitor as
shown in Figure 4.11. Observe that in this model the wire still represents an equipotential
region, and that the wire itself does not introduce any delay. The only impact on performance is introduced by the loading effect of the capacitor on the driving gate. This capacitive lumped model is simple, yet effective, and is the model of choice for the analysis of
most interconnect wires in digital integrated circuits.
Rdriver
Vout
cwire
Vout
Vin
Driver
Clumped
Figure 4.11 Distributed versus lumped capacitance model of wire. Clumped = L×cwire, with L the length of the
wire and cwire the capacitance per unit length. The driver is modeled as a voltage source and a source
resistance Rdriver.
Example 4.5 Lumped capacitance model of wire
For the circuit of Figure 4.11, assume that a driver with a source resistance of 10 kΩ is used to
drive a 10 cm long, 1 µm wide Al1 wire. In Example 4.1, we have found that the total lumped capacitance for this wire equals 11 pF.
The operation of this simple RC network is described by the following ordinary differential
equation (similar to the expression derived in Example 1.6):
C lumped
dV out V out – V in
+ ----------------------- = 0
dt
R driver
When applying a step input (with Vin going from 0 to V), the transient response of this circuit is
known to be an exponential function, and is given by the following expression (where τ =
Rdriver×Clumped, the time constant of the network):
Vout(t) = (1 − e−t/τ) V
The time to reach the 50% point is easily computed as t = ln(2)τ = 0.69τ. Similarly, it takes t
= ln(9)τ = 2.2τ to get to the 90% point. Plugging in the numbers for this specific example yields
t50% = 0.69 × 10 KΩ × 11 pF = 76 nsec
t90% =2.2 × 10 KΩ × 11 pF = 242 nsec
chapter4.fm Page 150 Friday, January 18, 2002 9:00 AM
THE WIRE
150
Chapter 4
These numbers are not even acceptable for the lowest performance digital circuits. Techniques to
deal with this bottleneck, such as reducing the source resistance of the driver, will be introduced in
Chapter ZZZ.
While the lumped capacitor model is the most popular, sometimes it is also useful to
present lumped models of a wire with respect to either resistance and inductance. This is
often the case when studying the supply distribution network. Both the resistance and
inductance of the supply wires can be interpreted as parasitic noise sources that introduce
voltage drops and bounces on the supply rails.
4.4.3
The Lumped RC model
On-chip metal wires of over a few mm length have a significant resistance. The equipotential assumption, presented in the lumped-capacitor model, is no longer adequate, and a
resistive-capacitive model has to be adopted.
A first approach lumps the total wire resistance of each wire segment into one single
R and similarly combines the global capacitance into a single capacitor C. This simple
model, called the lumped RC model is pessimistic and inaccurate for long interconnect
wires, which are more adequately represented by a distributed rc-model. Yet, before analyzing the distributed model, its is worthwhile to spend some time on the analysis and the
modeling of lumped RC networks for the following reasons:
• The distributed rc-model is complex and no closed form solutions exist. The behavior of the distributed rc-line can be adequately modeled by a simple RC network.
• A common practice in the study of the transient behavior of complex transistor-wire
networks is to reduce the circuit to an RC network. Having a means to analyze such
a network effectively and to predict its first-order response would add a great asset
to the designers tool box.
In Example 4.5, we analyzed a single resistor-single capacitor network. The behavior of
such a network is fully described by a single differential equation, and its transient waveform is a modeled by an exponential with a single time-constant (or network pole). Unfortunately, deriving the correct waveforms for a network with a larger number of capacitors
and resistors rapidly becomes hopelessly complex: describing its behavior requires a set of
ordinary differential equations, and the network now contains many time-constants (or
poles and zeros). Short of running a full-fledged SPICE simulation, delay calculation
methods such as the Elmore delay formula come to the rescue [Elmore48].
Consider the resistor-capacitor network of Figure 4.12. This circuit is called an RCtree and has the following properties:
• the network has a single input node (called s in Figure 4.12)
• all the capacitors are between a node and the ground
• the network does not contain any resistive loops (which makes it a tree)
An interesting result of this particular circuit topology is that there exists a unique resistive
path between the source node s and any node i of the network. The total resistance along
chapter4.fm Page 151 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
151
2
R2
s
R1
C2
1
4
1
0
R4
C1
C4
R3
3
Ri
C3
i
Ci
Figure 4.12
Tree-structured RC network.
this path is called the path resistance Rii. For example, the path resistance between the
source node s and node 4 in the example of Figure 4.12 equals
R44 = R1 + R3 + R4
The definition of the path resistance can be extended to address the shared path
resistance Rik, which represents the resistance shared among the paths from the root node s
to nodes k and i:
R ik =
∑ R ⇒ ( R ∈ [ path ( s → i ) ∩ path ( s → k )] )
j
j
(4.12)
For the circuit of Figure 4.12, Ri4 = R1 + R3 while Ri2 = R1.
Assume now that each of the N nodes of the network is initially discharged to GND,
and that a step input is applied at node s at time t = 0. The Elmore delay at node i is then
given by the following expression:
N
τ Di =
∑C R
k
ik
(4.13)
k=1
The Elmore delay is equivalent to the first-order time constant of the network (or the first
moment of the impulse response). The designer should be aware that this time-constant
represents a simple approximation of the actual delay between source node and node i. Yet
in most cases this approximation has proven to be quite reasonable and acceptable. It
offers the designer a powerful mechanism for providing a quick estimate of the delay of a
complex network.
Example 4.6 RC delay of a tree-structured network
Using Eq. (4.13), we can compute the Elmore delay for node i in the network of Figure 4.12.
τDi = R1C1 + R1C2 + (R1 + R3)C3 + (R1 + R3)C4 + (R1 + R3 + Ri)Ci
As a special case of the RC tree network, let us consider the simple, non-branched
RC chain (or ladder) shown in Figure 4.13. This network is worth analyzing because it is a
structure that is often encountered in digital circuits, and also because it represents an
chapter4.fm Page 152 Friday, January 18, 2002 9:00 AM
THE WIRE
152
Chapter 4
approximative model of a resistive-capacitive wire. The Elmore delay of this chain network can be derived with the aid of Eq. (4.13):
Vin
R1
1
R2
Ri–1
2
i – 1 Ri
RN
i
N
VN
C1
Figure 4.13
C2
Ci–1
Ci
CN
RC chain.
N
τ DN =
∑C ∑R
i
i=1
N
i
j=1
j
=
∑C R
i
ii
(4.14)
i=1
or the shared-path resistance is replaced by simply the path resistance. As an example,
consider node 2 in the RC chain of Figure 4.13. Its time-constant consists of two components contributed by nodes 1 and 2. The component of node 1 consists of C1R1 with R1 the
total resistance between the node and the source, while the contribution of node 2 equals
C2(R1 + R2). The equivalent time constant at node 2 equals C1R1 + C2(R1 + R2). τi of node
i can be derived in a similar way.
τDi = C1R1 + C2(R1 + R2) + … + Ci(R1 + R2 + … + Ri)
Example 4.7 Time-Constant of Resistive-Capacitive Wire
The model presented in Figure 4.13 can be used as an approximation of a resistive-capacitive wire.
The wire with a total length of L is partitioned into N identical segments, each with a length of L/N.
The resistance and capacitance of each segment are hence given by rL/N and cL/N, respectively.
Using the Elmore formula, we can compute the dominant time-constant of the wire:
2 N( N + 1 )
L 2
N+1
τ DN = ---- ( rc + 2rc + … + Nrc ) = ( rcL ) ---------------------- = RC ------------ N
2
2N
2N
(4.15)
with R (= rL) and C (= cL) the total lumped resistance and capacitance of the wire. For very large
values of N, this model asymptotically approaches the distributed rc line. Eq. (4.15) then simplifies
to the following expression:
2
RC
rcL
τ DN = -------- = ----------2
2
(4.16)
Eq. (4.16) leads to two important conclusions:
• The delay of a wire is a quadratic function of its length! This means that doubling
the length of the wire quadruples its delay.
• The delay of the distributed rc-line is one half of the delay that would have been
predicted by the lumped RC model. The latter combines the total resistance and
capacitance into single elements, and has a time-constant equal to RC (as is also
chapter4.fm Page 153 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
153
obtained by setting N = 1 in Eq. (4.15)). This confirms the observation made earlier
that the lumped model presents a pessimistic view on the delay of resistive wire.
WARNING: Be aware that an RC-chain is characterized by a number of time-constants.
The Elmore expression determines the value of only the dominant one, and presents thus a
first-order approximation.
The Elmore delay formula has proven to be extremely useful. Besides making it
possible to analyze wires, the formula can also be used to approximate the propagation
delay of complex transistor networks. In the switch model, transistors are replaced by their
equivalent, linearized on-resistance. The evaluation of the propagation delay is then
reduced to the analysis of the resulting RC network. More precise minimum and maximum bounds on the voltage waveforms in an RC tree have further been established
[Rubinstein83]. These bounds have formed the base for most computer-aided timing analyzers at the switch and functional level [Horowitz83]. An interesting result [Lin84] is that
the exponential voltage waveform with the Elmore delay as time constant is always situated between these min and max bounds, which demonstrates the validity of the Elmore
approximation.
4.4.4
The Distributed rc Line
In the previous paragraphs, we have shown that the lumped RC model is a pessimistic
model for a resistive-capacitive wire, and that a distributed rc model (Figure 4.14a) is
more appropriate. As before, L represents the total length of the wire, while r and c stand
for the resistance and capacitance per unit length. A schematic representation of the distributed rc line is given in Figure 4.14b.
Vin
r∆ L
c∆ L
r∆ L
Vi-1
r∆ L
Vi
c∆L
c∆ L
r∆ L
Vi+1
c ∆L
L
(a) Distributed model
(r,c,L)
Vin
Vout
(b) Schematic symbol for distributed RC line
Figure 4.14 Distributed RC line wire-model and its schematic symbol.
r∆ L
c∆ L
Vout
chapter4.fm Page 154 Friday, January 18, 2002 9:00 AM
THE WIRE
154
Chapter 4
The voltage at node i of this network can be determined by solving the following set
of partial differential equations:
c∆L
∂V i
( Vi + 1 – Vi ) + ( Vi – 1 – Vi )
= -----------------------------------------------------------∂t
r∆L
(4.17)
The correct behavior of the distributed rc line is then obtained by reducing ∆L asymptotically to 0. For ∆L → 0, Eq. (4.17) becomes the well-known diffusion equation:
2
rc
∂V
∂V
=
∂t
∂x2
(4.18)
where V is the voltage at a particular point in the wire, and x is the distance between this
point and the signal source. No closed-form solution exists for this equation, but approximative expressions such as the formula presented in Eq. (4.19) can be derived
[Bakoglu90]. These equations are difficult to use for ordinary circuit analysis. It is known
however that the distributed rc line can be approximated by a lumped RC ladder network,
which can be easily used in computer-aided analysis. Some of these models will be presented in a later section, discussing SPICE wire models.
RC
V out ( t ) = 2erfc( --------)
4t
= 1.0 – 1.366e
t « RC
(4.19)
t– 2.5359 ------RC
+ 0.366e
t– 9.4641 ------RC
t » RC
Figure 4.15 shows the response of a wire to a step input, plotting the waveforms at
different points in the wire as a function of time. Observe how the step waveform “diffuses” from the start to the end of the wire, and the waveform rapidly degrades, resulting
in a considerable delay for long wires. Driving these rc lines and minimizing the delay and
signal degradation is one of the trickiest problems in modern digital integrated circuit
design. It hence will receive considerable attention in later chapters.
2.5
x= L/10
2
voltage (V)
x = L/4
1.5
x = L/2
1
x= L
0.5
0
0
0.5
1
1.5
2
2.5
3
time (nsec)
3.5
4
4.5
5
Figure 4.15 Simulated step response of resistive-capacitive wire as a function of time and place.
chapter4.fm Page 155 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
155
Some of the important reference points in the step response of the lumped and the
distributed RC model of the wire are tabulated in Table 4.7. For instance, the propagation
delay (defined at 50% of the final value) of the lumped network not surprisingly equals
0.69 RC. The distributed network, on the other hand, has a delay of only 0.38 RC, with R
and C the total resistance and capacitance of the wire. This confirms the result of Eq.
(4.16).
Table 4.7
Step response of lumped and distributed RC networks—points of Interest.
Voltage range
Lumped RC network
Distributed RC network
0 → 50% (tp)
0.69 RC
0.38 RC
0 → 63% (τ)
RC
0.5 RC
10% → 90% (tr)
2.2 RC
0.9 RC
0% → 90%
2.3 RC
1.0 RC
Example 4.8 RC delay of Aluminum Wire
Let us consider again the 10 cm long, 1 µm wide Al1 wire of Example 4.1. In Example 4.4, we
derived the following values for r and c:
c = 110 aF/µm; r = 0.075 Ω/µm;
Using the entry of Table 4.7, we derive the propagation delay of the wire:
tp = 0.38 RC = 0.38 × (0.075 Ω/µm) × (110 aF/µm) × (105 µm)2 = 31.4 nsec
We can also deduce the propagation delays of an identical wire implemented in polysilicon
and Al5. The values of the capacitances are obtained from Table 4.2, while the resistances are
assumed to be respectively 150 Ω/µm and 0.0375 Ω/µm for Poly and Al5:
Poly: tp = 0.38 × (150 Ω/µm) × (88 + 2 × 54 aF/µm) × (105 µm)2 = 112 µsec!
Al5: tp = 0.38 × (0.0375 Ω/µm) × (5.2 + 2 × 12 aF/µm) × (105 µm)2 = 4.2 nsec
Obviously, the choice of the interconnect material and layer has a dramatic impact on the delay of
the wire.
An important question for a designer to answer when analyzing an interconnect network
whether the effects of RC delays should be considered, or whether she can get away with a
simpler lumped capacitive model. A simple rule of thumb proves to be very useful here.
Design Rules of Thumb
• rc delays should only be considered when tpRC >> tpgate of the driving gate.
This translates into Eq. (4.20), which determines the critical length L of the interconnect
wire where RC delays become dominant.
chapter4.fm Page 156 Friday, January 18, 2002 9:00 AM
THE WIRE
156
L crit >>
t pgate
--------------0.38rc
Chapter 4
(4.20)
The actual value of Lcrit depends upon the sizing of the driving gate and the chosen interconnect material.
• rc delays should only be considered when the rise (fall) time at the line input is
smaller than RC, the rise (fall) time of the line.
t rise < RC
(4.21)
with R and C the total resistance and capacitance of the wire. When this condition is not
met, the change in signal is slower than the propagation delay of the wire, and a lumped capacitive model suffices.
Example 4.9 RC versus Lumped C
The presented rule can be illustrated with the aid of the simple circuit shown in Figure
4.16. It is assumed here that the driving gate can be modeled as voltage source with a
finite source resistance Rs. The total propagation delay of the network can be approximated by the following expression, obtained by applying the Elmore formula:2
(rw,cw,L)
Rs
Vout
Vin
Figure 4.16 rc-line of length L driven by source with
resistance equal to Rs.
Rw Cw
2
- = R s C w + 0.5r w c w L
τ D = R s C w + ------------2
and
t p = 0.69R s C w + 0.38R w C w
with Rw = rL and Cw = cL. The delay introduced by the wire resistance becomes dominant
when (RwCw)/2 ≥ RsCw, or L ≥ 2Rs/r. Assume now a driver with a source resistance of 1
kΩ, driving an Al1 wire of 1 µm wide (r = 0.075 Ω/µm). This leads to a critical length of
2.67 cm.
2
Hint: replace the wire by the lumped RC network of Figure 4.13 and apply the Elmore equation on the
resulting network.
chapter4.fm Page 157 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
4.4.5
157
The Transmission Line
When the switching speeds of the circuits become sufficiently fast, and the quality of the
interconnect material become high enough so that the resistance of the wire is kept within
bounds, the inductance of the wire starts to dominate the delay behavior, and transmission
line effects must be considered. This is more precisely the case when the rise and fall times
of the signal become comparable to the time of flight of the signal waveform across the
line as determined by the speed of light. With the advent of Copper interconnect and the
high switching speeds enabled by the deep-submicron technologies, transmission line
effects are soon to be considered in the fastest CMOS designs.
In this section, we first analyze the transmission line model. Next, we apply it to the
current semiconductor technology and determine when those effects should be actively
considered in the design process.
Transmission Line Model
Similar to the resistance and capacitance of an interconnect line, the inductance is distributed over the wire. A distributed rlc model of a wire, known as the transmission line
model, becomes the most accurate approximation of the actual behavior. The transmission
line has the prime property that a signal propagates over the interconnection medium as a
wave. This is in contrast to the distributed rc model, where the signal diffuses from the
source to the destination governed by the diffusion equation, Eq. (4.18). In the wave
mode, a signal propagates by alternatively transferring energy from the electric to the
magnetic fields, or equivalently from the capacitive to the inductive modes.
Consider the point x along the transmission line of Figure 4.17 at time t. The following set of equations holds:
Vin
r
r
l
g
Figure 4.17
c
r
l
c
g
l
g
x
c
r
l
g
Vout
c
Lossy transmission line.
∂v
∂i
= – ri – l
∂x
∂t
∂i
∂v
= – gv – c
∂x
∂t
(4.22)
Assuming that the leakage conductance g equals 0, which is true for most insulating materials, and eliminating the current i yields the wave propagation equation, Eq. (4.23).
2
2
∂ v = rc ∂v + lc ∂ v
∂t
∂x2
∂ t2
(4.23)
chapter4.fm Page 158 Friday, January 18, 2002 9:00 AM
THE WIRE
158
Chapter 4
where r, c, and l are the resistance, capacitance, and inductance per unit length,
respectively.
To understand the behavior of the transmission line, we will first assume that the
resistance of the line is small. In this case, a simplified capacitive/inductive model, called
the lossless transmission line, is appropriate. This model is applicable for wires at the
printed-circuit board level. Due to the high conductivity of the Copper interconnect material used there, the resistance of the transmission line can be ignored. On the other hand,
resistance plays an important role in integrated circuits, and a more complex model, called
the lossy transmission line should be considered. The lossy model is only discussed briefly
at the end.
The Lossless Transmission Line
For the lossless line, Eq. (4.23) simplifies to the ideal wave equation:
2
2
2
∂ v = lc ∂ v = ---1- ∂ v
∂x2
∂ t2
ν2 ∂ t2
(4.24)
A step input applied to a lossless transmission line propagates along the line with a
speed ν, given by Eq. (4.11) and repeated below.
c0
1 = ------------1 = ---------ν = -------εr µr
εµ
lc
(4.25)
Even though the values of both l and c depend on the geometric shape of the wire, their
product is a constant and is only a function of the surrounding media. The propagation
delay per unit wire length (tp) of a transmission line is the inverse of the speed:
tp =
(4.26)
lc
Let us now analyze how a wave propagates along a lossless transmission line. Suppose
that a voltage step V has been applied at the input and has propagated to point x of the line
(Figure 4.18). All currents are equal to 0 at the right side of x, while the voltage over the
line equals V at the left side. An additional capacitance cdx must be charged for the wave
to propagate over an additional distance dx. This requires the following current:
I =
dQ
dx
= c V = cνV =
dt
dt
c
--V
l
(4.27)
since the propagation speed of the signal dx/dt equals ν. This means that the signal sees
the remainder of the line as areal impedance,
V
Z 0 = --- =
I
1
εµ
l
-- = ---------- = ------ .
cν
c
c
(4.28)
This impedance, called the characteristic impedance of the line, is a function of the
dielectric medium and the geometry of the conducting wire and isolator (Eq. (4.28)), and
is independent of the length of the wire and the frequency. That a line of arbitrary length
has a constant, real impedance is a great feature as it simplifies the design of the driver cir-
chapter4.fm Page 159 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
159
dx
V
Wire
I
Substrate
x
Direction of propagation
Figure 4.18 Propagation of
voltage step along a lossless
transmission line.
cuitry. Typical values of the characteristic impedance of wires in semiconductor circuits
range from 10 to 200 Ω.
Example 4.10
Propagation Speeds of Signal Waveforms
The information of Table 4.6 shows that it takes 1.5 nsec for a signal wave to propagate from
source-to-destination on a 20 cm wire deposited on an epoxy printed-circuit board. If transmission line effects were an issue on silicon integrated circuits, it would take 0.67 nsec for the
signal to reach the end of a 10 cm wire.
WARNING: The characteristic impedance of a wire is a function of the overall interconnect topology. The electro-magnetic fields in complex interconnect structures tend to be
irregular, and are strongly influenced by issues such as the current return path. Providing a
general answer to the latter problem has so far proven to be illusive, and no closed-formed
analytical solutions are typically available. Hence, accurate inductance and characteristic
impedance extraction is still an active research topic. For some simplified structures,
approximative expressions have been derived. For instance, the characteristic impedances
of a triplate strip-line (a wire embedded in between two ground planes) and a semiconductor micro strip-line (wire above a semiconductor substrate) are approximated by Eq. (4.29)
and Eq. (4.30), respectively.
µ
+ W-
--------------Z 0 ( triplate ) ≈ 94Ω -----r ln 2t
εr H + W
(4.29)
µr
4t
-
- ln --------------------------------------Z 0 ( microstrip ) ≈ 60Ω ---------------------------------0.475ε r + 0.67 0.536W + 0.67H
(4.30)
and
Termination
The behavior of the transmission line is strongly influenced by the termination of the line.
The termination determines how much of the wave is reflected upon arrival at the wire
chapter4.fm Page 160 Friday, January 18, 2002 9:00 AM
THE WIRE
160
Chapter 4
end. This is expressed by the reflection coefficient ρ that determines the relationship
between the voltages and currents of the incident and reflected waveforms.
V refl
I refl
R–Z
- = -------- = ---------------0
ρ = --------R + Zo
V inc
I inc
(4.31)
where R is the value of the termination resistance. The total voltages and currents at the
termination end are the sum of incident and reflected waveforms.
V = V inc ( 1 + ρ )
(4.32)
I = I inc ( 1 – ρ )
Three interesting cases can be distinguished, as illustrated in Figure 4.19. In case
(a) the terminating resistance is equal to the characteristic impedance of the line. The termination appears as an infinite extension of the line, and no waveform is reflected. This
is also demonstrated by the value of ρ, which equals 0. In case (b), the line termination is
Incident wave
Z0
V
Reflected wave
Z0
(a) Matched termination
Z0
L
x
L
x
L
x
V
(b) Open-circuit termination
Z0
V
(c) Short-circuit termination
Figure 4.19 Behavior of various transmission line terminations.
an open circuit (R = ∞), and ρ = 1. The total voltage waveform after reflection is twice
the incident one as predicted by Eq. (4.32). Finally, in case (c) where the line termination
is a short circuit, R = 0, and ρ = –1. The total voltage waveform after reflection equals
zero.
The transient behavior of a complete transmission line can now be examined. It is
influenced by the characteristic impedance of the line, the series impedance of the source
ZS, and the loading impedance ZL at the destination end, as shown in Figure 4.20.
Consider first the case where the wire is open at the destination end, or ZL = ∞, and
ρL = 1. An incoming wave is completely reflected without phase reversal. Under the
assumption that the source impedance is resistive, three possible scenarios are sketched in
Figure 4.21: RS = 5 Z0, RS = Z0, and RS = 1/5 Z0.
1. Large source resistance—RS = 5 Z0 (Figure 4.21a)
chapter4.fm Page 161 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
161
ZS
Z0
ZL
Figure 4.20 Transmission line
with terminating impedances.
5
4
Vdest
V
3
Vsource
2
1
(a) RS = 5Z0, RL = ×
0
4
V
3
2
1
(b) RS = Z0, RL = ×
0
8
V
6
4
2
(c) RS = Z0/5, RL = ×
00
Figure 4.21
5
10
t (in tflight)
Transient response of transmission line.
15
Only a small fraction of the incoming signal Vin is injected into the transmission
line. The amount injected is determined by the resistive divider formed by the source
resistance and the characteristic impedance Z0.
Vsource = (Z0 / (Z0 + RS)) Vin = 1/6 × 5 V = 0.83 V
(4.33)
This signal reaches the end of the line after L/ν sec, where L stands for the length of
the wire and is fully reflected, which effectively doubles the amplitude of the wave
(Vdest = 1.67 V). The time it takes for the wave to propagate from one end of the wire to
chapter4.fm Page 162 Friday, January 18, 2002 9:00 AM
THE WIRE
162
Chapter 4
the other is called the time-of-flight, tflight = L/ν. Approximately the same happens when
the wave reaches the source node again. The incident waveform is reflected with an amplitude determined by the source reflection coefficient, which equals 2/3 for this particular
case.
5Z 0 – Z 0
2
- = --ρ S = -------------------3
5Z 0 + Z 0
(4.34)
The voltage amplitude at source and destination nodes gradually reaches its final value of
Vin. The overall rise time is, however, many times L/ν.
When multiple reflections are present, as in the above case, keeping track of waves
on the line and total voltage levels rapidly becomes cumbersome. Therefore a graphical
construction called the lattice diagram is often used to keep track of the data (Figure
4.22). The diagram contains the values of the voltages at the source and destination ends,
as well as the values of the incident and reflected wave forms. The line voltage at a termination point equals the sum of the previous voltage, the incident, and reflected waves.
Vsource
Vdest
0.8333 V
+ 0.8333
1.6666 V
+ 0.8333
2.2222 V
+ 0.5556
2.7778 V
+ 0.5556
t
+ 0.3704
3.1482 V
3.5186 V
+ 0.3704
3.7655 V
+ 0.2469
4.0124 V
+ 0.2469
...
L/ν
Figure 4.22 Lattice diagram for
RS = 5 Z0 and RL = ∞. Vstep = 5 V,
(as in Figure 4.21a).
2. Small source resistance—RS = Z0/5 (Figure 4.21c)
A large portion of the input is injected in the line. Its value is doubled at the destination end, which causes a severe overshoot. At the source end, the phase of the signal is
reversed (ρS = −2/3). The signal bounces back and forth and exhibits severe ringing. It
takes multiple L/ν before it settles.
3. Matched source resistance—RS = Z0 (Figure 4.21b)
Half of the input signal is injected at the source. The reflection at the destination end
doubles the signal, so that the final value is reached immediately. It is obvious that this is
the most effective case.
Note that the above analysis is an ideal one, as it is assumed that the input signal has
a zero rise time. In real conditions the signals are substantially smoother, as demonstrated
in the simulated response of Figure 4.23 (for RS = Z0/5 and tr = tflight).
chapter4.fm Page 163 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
163
10
Vdest
V (V)
8
Vsource
Vin
6
4
2
0
0
Problem 4.1
100
200
300
t (psec)
400
500
Figure 4.23 Simulated transient
response of lossless transmission
line for finite input rise times ( RS =
Z0/5, tr = tflight).
Transmission Line Response
Derive the lattice diagram of the above transmission line for RS = Z0/5, RL = ∞, and Vstep = 5
V. Also try the reverse picture—assume that the series resistance of the source equals zero,
and consider different load impedances.
Example 4.11
Capacitive Termination
Loads in MOS digital circuits tend to be of a capacitive nature. One might wonder how this
influences the transmission line behavior and when the load capacitance should be taken into
account.
The characteristic impedance of the transmission line determines the current that can be
supplied to charge capacitive load CL. From the load’s point of the view, the line behaves as a
resistance with value Z0. The transient response at the capacitor node, therefore, displays a
time constant Z0CL. This is illustrated in Figure 4.24, which shows the simulated transient
response of a series-terminated transmission line with a characteristic impedance of 50 Ω
loaded by a capacitance of 2 pF. The response shows how the output rises to its final value
with a time-constant of 100 psec (= 50 Ω × 2 pF) after a delay equal to the time-of-flight of
the line.
This asymptotic response causes some interesting artifacts. After 2 tflight, an unexpected
voltage dip occurs at the source node that can be explained as follows. Upon reaching the destination node, the incident wave is reflected. This reflected wave also approaches its final
value asymptotically. Since Vdest equals 0 initially instead of the expected jump to 5 V, the
reflection equals −2.5 V rather than the expected 2.5 V. This forces the transmission line temporarily to 0 V, as shown in the simulation. This effect gradually disappears as the output
node converges to its final value.
The propagation delay of the line equals the sum of the time-of-flight of the line (= 50
psec) and the time it takes to charge the capacitance (= 0.69 Z0 CL = 69 psec). This is exactly
what the simulation yields. In general, we can say that the capacitive load should only be considered in the analysis when its value is comparable to or larger than the total capacitance of
the transmission line [Bakoglu90].
chapter4.fm Page 164 Friday, January 18, 2002 9:00 AM
THE WIRE
164
Chapter 4
5.0
Vdest
4.0
V
3.0
Vsource
2.0
1.0
0.0
0
0.1
0.2
0.3
time (nsec)
0.4
0.5
Figure 4.24 Capacitively
terminated transmission line: RS =
50 Ω, RL = ∞, CL = 2 pF, Z0 = 50 Ω,
tflight = 50 psec.
Lossy Transmission Line
While board and module wires are thick and wide enough to be treated as lossless transmission lines, the same is not entirely true for on-chip interconnect where the resistance of
the wire is an important factor. The lossy transmission-line model should be applied
instead. Going into detail about the behavior of a lossy line would lead us to far astray. We
therefore only discuss the effects of resistive loss on the transmission line behavior in a
qualitative fashion.
The response of a lossy RLC line to a unit step combines wave propagation with a
diffusive component. This is demonstrated in Figure 4.25, which plots the response of the
RLC transmission line as a function of distance from the source. The step input still propagates as a wave through the line. However, the amplitude of this traveling wave is attenuated along the line:
V step ( x )
= e
------------------V step ( 0 )
r
– --------- x
2Z 0
(4.35)
The arrival of the wave is followed by a diffusive relaxation to the steady-state value
at point x. The farther it is from the source, the more the response resembles the behavior
of a distributed RC line. In fact, the resistive effect becomes dominant, and the line
behaves as a distributed RC line when R (= rL, the total resistance of the line) >> 2 Z0.
When R = 5 Z0, only 8% of the original step reaches the end of the line. At that point, the
line is more appropriately modeled as a distributed rc line.
Be aware that the actual wires on chips, boards, or substrates behave in a far more
complex way than predicted by the above analysis. For instance, branches on wires, often
called transmission line taps, cause extra reflections and can affect both signal shape and
delay. Since the analysis of these effects is very involved, the only meaningful approach is
to use computer analysis and simulation techniques. For a more extensive discussion of
these effects, we would like to refer the reader to [Bakoglu90] and [Dally98].
chapter4.fm Page 165 Friday, January 18, 2002 9:00 AM
Section 4.4
Electrical Wire Models
165
Transmission line
Source
x=0
x = x1
x = x2
t
Dest
x = x3
t
t
Figure 4.25
x=L
x
t
t
Step response of lossy transmission line.
Design Rules of Thumb
Once again, we have to ask ourselves the question when it is appropriate to consider
transmission line effects. From the above discussion, we can derive two important constraints:
• Transmission line effects should be considered when the rise or fall time of the
input signal (tr, tf) is smaller than the time-of-flight of the transmission line (tflight).
This leads to the following rule of thumb, which determines when transmission line
effects should be considered:
Lt r ( t f ) < 2.5t flight = 2.5 -ν
(4.36)
For on-chip wires with a maximum length of 1 cm, one should only worry about transmission line effects when tr < 150 psec. At the board level, where wires can reach a length of
up to 50 cm, we should account for the delay of the transmission line when tr < 8 nsec. This
condition is easily achieved with state-of-the-art processes and packaging technologies. Ignoring the inductive component of the propagation delay can easily result in overly optimistic
delay predictions.
• Transmission line effects should only be considered when the total resistance of the
wire is limited:
R < 5Z 0
(4.37)
If this is not the case, the distributed RC model is more appropriate.
Both constraints can be summarized in the following set of bounds on the wire length:
tr 1
5 l
------ -------- < L < --- -2.5 lc
r c
(4.38)
• The transmission line is considered lossless when the total resistance is substantially
smaller than the characteristic impedance, or
chapter4.fm Page 166 Friday, January 18, 2002 9:00 AM
THE WIRE
166
Z
R < ----02
Example 4.12
Chapter 4
(4.39)
When to Consider Transmission Line Effects
Consider again our Al1 wire. Using the data from Example 4.4 and Eq. (4.28), we can
approximate the value of Z0 for various wire widths:
W = 0.1 µm: c = 92 aF/µm; Z0 = 74 Ω
W = 1.0 µm: c = 110 aF/µm; Z0 = 60 Ω
W = 10 µm: c = 380 aF/µm; Z0 = 17 Ω
For a wire with a width of 1µm, we can derive the maximum length of the wire for
which we should consider transmission line effects using Eq. (4.37):
5Z
5 × 60Ω
L max = --------0- = ------------------------------ = 4000µm
0.075Ω ⁄ µm
r
From Eq. (4.36), we find a corresponding maximum rise (or fall) time of the input signal
equal to
trmax = 2.5 × (4000 µm)/(15 cm/nsec) = 67 psec
This is hard to accomplish in current technologies. For these wires, a lumped capacitance
model is more appropriate. Transmission line effects are more plausible in wider wires. For a
10 µm wide wire, we find a maximum length of 11.3 mm, which corresponds to a maximum
rise time of 188 psec.
Assume now a Copper wire, implemented on level 5, with a characteristic impedance
of 200 Ω and a resistance of 0.025 Ω/µm. The resulting maximum wire length equals 40 mm.
Rise times smaller than 670 psec will cause transmission line effects to occur.
Be aware however that the values for Z0, derived in this example, are only approximations. In actual designs, more complex expressions or empirical data should be used.
Example 4.13
Simulation of Transmission Line Effects
Show SPICE simulation
4.5
SPICE Wire Models
In previous sections, we have discussed the various interconnect parasitics, and introduced
simple models for each of them. Yet, the full and precise impact of these effects can only
be found through detailed simulation. In this section, we introduce the models that SPICE
provides for the capacitive, resistive, and inductive parasitics.
chapter4.fm Page 167 Friday, January 18, 2002 9:00 AM
Section 4.5
4.5.1
SPICE Wire Models
167
Distributed rc Lines in SPICE
Because of the importance of the distributed rc-line in today’s design, most circuit simulators have built-in distributed rc-models of high accuracy. For instance, the Berkeley
SPICE3 simulator supports a uniform-distributed rc-line model (URC). This model
approximates the rc-line as a network of lumped RC segments with internally generated
nodes. Parameters include the length of the wire L and (optionally) the number of segments used in the model.
Example 4.14
SPICE3 URC Model
A typical example of a SPICE3 instantiation of a distributed rc-line is shown below. N1 and
N2 represent the terminal nodes of the line, while N3 is the node the capacitances are connected to. RPERL and CPERL stand for the resistance and capacitance per meter.
U1 N1=1 N2=2 N3=0 URCMOD L=50m N=6
.MODEL URCMOD URC(RPERL=75K CPERL=100pF)
If your simulator does not support a distributed rc-model, or if the computational
complexity of these models slows down your simulation too much, you can construct a
simple yet accurate model yourself by approximating the distributed rc by a lumped RC
network with a limited number of elements. Figure 4.26 shows some of these approximations ordered along increasing precision and complexity. The accuracy of the model is
determined by the number of stages. For instance, the error of the π3 model is less than
3%, which is generally sufficient.
4.5.2
Transmission Line Models in SPICE
SPICE supports a lossless transmission line model. The line characteristics are defined by
the characteristic impedance Z0, while the length of the line can be defined in either of two
forms. A first approach is to directly define the transmission delay TD, which is equivalent to the time-of-flight. Alternatively, a frequency F may be given together with NL, the
dimensionless, normalized electrical length of the transmission line, which is measured
with respect to the wavelength in the line at the frequency F. The following relation is
valid.
NL = F ⋅ TD
(4.40)
No lossy transmission line model is currently provided. When necessary, loss can be
added by breaking up a long transmission line into shorter sections and adding a small
series resistance in each section to model the transmission line loss. Be careful when using
this approximation. First of all, the accuracy is still limited. Secondly, the simulation
speed might be severely effected, since SPICE chooses a time step that is less than or
equal to half of the value of TD. For small transmission lines, this time step might be much
smaller than what is needed for transistor analysis.
chapter4.fm Page 168 Friday, January 18, 2002 9:00 AM
THE WIRE
168
R
R/2
C/2
C
π
T
R/2
R/2
R/4
C/2
R/2
C/4
C/6
R/3
C/3
R/6
C/6
π3
Figure 4.26
4.6
C/2
T2
R/3
C/3
R/4
C/2
π2
R/3
R/2
C/2
C/4
Chapter 4
R/3
R/3
C/3
C/3
R/6
C/3
T3
Simulation models for distributed RC line.
Perspective: A Look into the Future
Similar to the approach we followed for the MOS transistor, it is worthwhile to explore
how the wire parameters will evolve with further scaling of the technology. As transistor
dimensions are reduced, the interconnect dimensions must also be reduced to take full
advantage of the scaling process.
A straightforward approach is to scale all dimensions of the wire by the same factor
S as the transistors (ideal scaling). This might not be possible for at least one dimension of
the wire, being the length. It can be surmised that the length of local interconnections —
wires that connect closely grouped transistors — scales in the same way as these transistors. On the other hand, global interconnections, that provide the connectivity between
large modules and the input-output circuitry, display a different scaling behavior. Examples of such wires are clock signals, and data and instruction buses. Figure 4.27 contains a
histogram showing the distribution of the wire lengths in an actual microprocessor design,
containing approximately 90,000 gate) [Davis98]. While most of the wires tend to be only
a couple of gate pitches long, a substantial number of them are much longer and can reach
lengths up to 500 gate pitches.
The average length of these long wires is proportional to the die size (or complexity)
of the circuit. An interesting trend is that while transistor dimensions have continued to
shrink over the last decades, the chip sizes have gradually increased. In fact, the size of the
typical die (which is the square root of the die area) is increasing by 6% per year, doubling
chapter4.fm Page 169 Friday, January 18, 2002 9:00 AM
Section 4.6
Perspective: A Look into the Future
169
Figure 4.27 Distribution of wire
lengths in an advanced
microprocessor as a function of
the gate pitch.
about every decade. Chips have scaled from 2 mm × 2 mm in the early 1960s to approximately 2 cm × 2 cm in 2000. They are projected to reach 4 cm on the side by 2010!
This argues that when studying the scaling behavior of the wire length, we have to
differentiate between local and global wires. In our subsequent analysis, we will therefore
consider three models: local wires (SL = S > 1), constant length wires (SL = 1), and global
wires (SL = SC < 1).
Assume now that all other wire dimensions of the interconnect structure (W, H, t)
scale with the technology factor S. This leads to the scaling behavior illustrated in Table
4.8. Be aware that this is only a first-order analysis, intended to look at overall trends.
Effects such a fringing capacitance are ignored, and breakthroughs in semiconductor technology such as new interconnect and dielectric materials are also not considered.
Table 4.8
Ideal Scaling of Wire Properties
Parameter
Relation
Local Wire
Constant Length
Global Wire
W, H, t
1/S
1/S
1/S
L
1/S
1
1/SC
C
LW/t
1/S
1
1/SC
R
L/WH
S
S2
S2/SC
CR
L2/Ht
1
S2
S2/SC2
The eye-catching conclusion of this exercise is that scaling of the technology does
not reduce wire delay (as personified by the RC time-constant). A constant delay is predicted for local wires, while the delay of the global wires goes up with 50% per year (for S
= 1.15 and SC = 0.94). This is in great contrast with the gate delay, which reduces from
year to year. This explains why wire delays are starting to play a predominant role in
today’s digital integrated circuit design.
The ideal scaling approach clearly has problems, as it causes a rapid increase in wire
resistance. This explains why other interconnect scaling techniques are attractive. One
chapter4.fm Page 170 Friday, January 18, 2002 9:00 AM
THE WIRE
170
Chapter 4
option is to scale the wire thickness at a different rate. The “constant resistance” model of
Table 4.9 explores the impact of not scaling the wire thickness at all. While this approach
seemingly has a positive impact on the performance, it causes the fringing and inter-wire
capacitance components to come to the foreground. We therefore introduce an extra
capacitance scaling factor εc (> 1), that captures the increasingly horizontal nature of the
capacitance when wire widths and pitches are shrunk while the height is kept constant.
Table 4.9
“Constant Resistance” Scaling of Wire Properties
Parameter
Relation
Local Wire
Constant Length
Global Wire
W, t
1/S
1/S
1/S
H
1
1
1
L
1/S
1
1/SC
C
εcLW/t
εc/S
εc
εc/SC
R
L/WH
1
S
S/SC
εc/S
εcS
εcS/SC2
CR
2
L /Ht
This scaling scenario offers a slightly more optimistic perspective, assuming of
course that εc < S. Yet, delay is bound to increase substantially for intermediate and long
wires, independent of the scaling scenario. To keep these delays from becoming excessive, interconnect technology has to be drastically improved. One option is to use better
interconnect (Cu) and insulation materials (polymers and air). The other option is to differentiate between local and global wires. In the former, density and low-capacitance are
crucial, while keeping the resistance under control is crucial in the latter. To address these
conflicting demands, modern interconnect topologies combine a dense and thin wiring
grid at the lower metal layers with fat, widely spaced wires at the higher levels, as is illustrated in Figure 4.28. Even with these advances, it is obvious that interconnect will play a
dominant role in both high-performance and low-energy circuits for years to come.
4.7
Summary
This chapter has presented a careful and in-depth analysis of the role and the behavior of
the interconnect wire in modern semiconductor technology. The main goal is to identify
the dominant parameters that set the values of the wire parasitics (being capacitance, resistance, and inductance), and to present adequate wire models that will aid us in the further
analysis and optimization of complex digital circuits.
chapter4.fm Page 171 Friday, January 18, 2002 9:00 AM
Section 4.8
To Probe Further
171
M6
Global
M5
M4
intermodule
M3
M2
M1
poly
Intercell
Intracell
Figure 4.28 Interconnect hierarchy of 0.25 µm
CMOS process, drawn to scale.
substrate
4.8
To Probe Further
Interconnect and its modeling is a hotly debated topic, that receives major attention in
journals and conferences. A number of textbooks and reprint volumes have been published. [Bakoglu90], [Tewksbury94], and [Dally98] present an in-depth coverage of interconnect issues, and are a valuable resource for further browsing.
REFERENCES
[Bakoglu90] H. Bakoglu, Circuits, Interconnections and Packaging for VLSI, Addison-Wesley,
1990.
[Dally98] B. Dally, Digital Systems Engineering, Cambridge University Press, 1998.
[Davis98] J. Davis and J. Meindl, “Is Interconnect the Weak Link?,” IEEE Circuits and Systems
Magazine, pp. 30-36, March 1998.
[Elmore48] E. Elmore, “The Transient Response of Damped Linear Networks with Particular
Regard to Wideband Amplifiers,” Journal of Applied Physics, pp. 55–63, January 1948.
[Etter93] D. Etter, “Engineering Problem Solving with Matlab,” Prentice Hall, 1993.
[Horowitz83] M. Horowitz, “Timing Models for MOS Circuits,” Ph.D. diss., Stanford University,
1983.
[Lin84] T.. Lin and C. Mead, “Signal delay in general RC networks,” IEEE Transactions on Computer-Aided Design, Vol. 3 No 4, pp. 321--349, 1984.
[Rubinstein83] J. Rubinstein, P. Penfield, and M. Horowitz, “Signal Delay in RC Networks,” IEEE
Transactions on Computer-Aided Design, vol. CAD-2, pp. 202–211, July 1983.
[Tewksbury94] S. Tewksbury, ed., Microelectronics System Interconnections—Performance and
Modeling, IEEE Press, 1994.
chapter4.fm Page 172 Friday, January 18, 2002 9:00 AM
172
THE WIRE
Chapter 4
[Vdmeijs84] N. Van De Meijs and J. Fokkema, “VLSI Circuit Reconstruction from Mask Topology,” Integration, vol. 2, no. 2, pp. 85–119, 1984.
chapter4.fm Page 173 Friday, January 18, 2002 9:00 AM
Section 4.8
To Probe Further
173
chapter5.fm Page 176 Friday, January 18, 2002 9:01 AM
CHAPTER
5
THE CMOS INVERTER
Quantification of integrity, performance, and energy metrics of an inverter
Optimization of an inverter design
5.1
Introduction
5.4.2
5.2
The Static CMOS Inverter — An Intuitive
Perspective
Propagation Delay: First-Order
Analysis
5.4.3
5.3
Evaluating the Robustness of the CMOS
Inverter: The Static Behavior
Propagation Delay from a Design
Perspective
Switching Threshold
5.5.1
Dynamic Power Consumption
5.3.2
Noise Margins
5.5.2
Static Consumption
Robustness Revisited
5.5.3
Putting It All Together
5.5.4
Analyzing Power Consumption Using
SPICE
Performance of CMOS Inverter: The Dynamic
Behavior
5.4.1
176
Power, Energy, and Energy-Delay
5.3.1
5.3.3
5.4
5.5
Computing the Capacitances
5.6
Perspective: Technology Scaling and its
Impact on the Inverter Metrics
chapter5.fm Page 177 Friday, January 18, 2002 9:01 AM
Section 5.1
5.1
Introduction
177
Introduction
The inverter is truly the nucleus of all digital designs. Once its operation and properties are
clearly understood, designing more intricate structures such as NAND gates, adders, multipliers, and microprocessors is greatly simplified. The electrical behavior of these complex circuits can be almost completely derived by extrapolating the results obtained for
inverters. The analysis of inverters can be extended to explain the behavior of more complex gates such as NAND, NOR, or XOR, which in turn form the building blocks for modules such as multipliers and processors.
In this chapter, we focus on one single incarnation of the inverter gate, being the
static CMOS inverter — or the CMOS inverter, in short. This is certainly the most popular
at present, and therefore deserves our special attention. We analyze the gate with respect
to the different design metrics that were outlined in Chapter 1:
• cost, expressed by the complexity and area
• integrity and robustness, expressed by the static (or steady-state) behavior
• performance, determined by the dynamic (or transient) response
• energy efficiency, set by the energy and power consumption
From this analysis arises a model of the gate that will help us to identify the parameters of the gate and to choose their values so that the resulting design meets desired specifications. While each of these parameters can be easily quantified for a given technology,
we also discuss how they are affected by scaling of the technology.
While this Chapter focuses uniquely on the CMOS inverter, we will see in the following Chapter that the same methodology also applies to other gate topologies.
5.2
The Static CMOS Inverter — An Intuitive Perspective
Figure 5.1 shows the circuit diagram of a static CMOS inverter. Its operation is readily
understood with the aid of the simple switch model of the MOS transistor, introduced in
Chapter 3 (Figure 3.25): the transistor is nothing more than a switch with an infinite offresistance (for |VGS| < |VT|), and a finite on-resistance (for |VGS| > |VT|). This leads to the
VDD
Vin
Vout
CL
Figure 5.1 Static CMOS inverter. VDD stands for the
supply voltage.
chapter5.fm Page 178 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
178
Chapter 5
following interpretation of the inverter. When Vin is high and equal to VDD, the NMOS
transistor is on, while the PMOS is off. This yields the equivalent circuit of Figure 5.2a. A
direct path exists between Vout and the ground node, resulting in a steady-state value of 0
V. On the other hand, when the input voltage is low (0 V), NMOS and PMOS transistors
are off and on, respectively. The equivalent circuit of Figure 5.2b shows that a path exists
between VDD and Vout, yielding a high output voltage. The gate clearly functions as an
inverter.
VDD
VDD
Rp
Vout
Vout
Rn
Vin = VDD
(a) Model for high input
Vin = 0
(b) Model for low input
Figure 5.2
inverter.
Switch models of CMOS
A number of other important properties of static CMOS can be derived from this switchlevel view:
• The high and low output levels equal VDD and GND, respectively; in other words,
the voltage swing is equal to the supply voltage. This results in high noise margins.
• The logic levels are not dependent upon the relative device sizes, so that the transistors can be minimum size. Gates with this property are called ratioless. This is in
contrast with ratioed logic, where logic levels are determined by the relative dimensions of the composing transistors.
• In steady state, there always exists a path with finite resistance between the output
and either VDD or GND. A well-designed CMOS inverter, therefore, has a low output impedance, which makes it less sensitive to noise and disturbances. Typical values of the output resistance are in kΩ range.
• The input resistance of the CMOS inverter is extremely high, as the gate of an MOS
transistor is a virtually perfect insulator and draws no dc input current. Since the
input node of the inverter only connects to transistor gates, the steady-state input
current is nearly zero. A single inverter can theoretically drive an infinite number of
gates (or have an infinite fan-out) and still be functionally operational; however,
increasing the fan-out also increases the propagation delay, as will become clear
below. So, although fan-out does not have any effect on the steady-state behavior, it
degrades the transient response.
chapter5.fm Page 179 Friday, January 18, 2002 9:01 AM
Section 5.2
The Static CMOS Inverter — An Intuitive Perspective
179
• No direct path exists between the supply and ground rails under steady-state operating conditions (this is, when the input and outputs remain constant). The absence of
current flow (ignoring leakage currents) means that the gate does not consume any
static power.
SIDELINE: The above observation, while seemingly obvious, is of crucial importance,
and is one of the primary reasons CMOS is the digital technology of choice at present. The
situation was very different in the 1970s and early 1980s. All early microprocessors, such
as the Intel 4004, were implemented in a pure NMOS technology. The lack of complementary devices (such as the NMOS and PMOS transistor) in such a technology makes
the realization of inverters with zero static power non-trivial. The resulting static power
consumption puts a firm upper bound on the number of gates that can be integrated on a
single die; hence the forced move to CMOS in the 1980s, when scaling of the technology
allowed for higher integration densities.
The nature and the form of the voltage-transfer characteristic (VTC) can be graphically deduced by superimposing the current characteristics of the NMOS and the PMOS
devices. Such a graphical construction is traditionally called a load-line plot. It requires
that the I-V curves of the NMOS and PMOS devices are transformed onto a common coordinate set. We have selected the input voltage Vin, the output voltage Vout and the NMOS
drain current IDN as the variables of choice. The PMOS I-V relations can be translated into
this variable space by the following relations (the subscripts n and p denote the NMOS
and PMOS devices, respectively):
I DSp = – IDSn
(5.1)
V GSn = V in ; V GSp = V in – V DD
V DSn = V out ; V DSp = V out – V DD
The load-line curves of the PMOS device are obtained by a mirroring around the xaxis and a horizontal shift over VDD. This procedure is outlined in Figure 5.3, where the
subsequent steps to adjust the original PMOS I-V curves to the common coordinate set Vin,
Vout and IDn are illustrated.
IDp
Vin = 0
IDn
IDn
Vin = 1.5
VDSp
Vin = 1.5
VDSp
VGSp = –1
VGSp = –2.5
Vin = VDD + VGSp
IDn = –IDp
Vin = 0
Vout = VDD + VDSp
Figure 5.3 Transforming PMOS I-V characteristic to a common coordinate set
(assuming VDD = 2.5 V).
Vout
chapter5.fm Page 180 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
180
IDn
PMOS
Vin = 0
Vin = 2.5
Vin = 0.5
Vin = 2
Vin = 1
Chapter 5
NMOS
Vin = 1.5
Vin = 1.5
Vin = 1
Vin = 1.5
Vin = 2
Vin = 1
Vin = 2.5
Vin = 0.5
Vin = 0
Vout
Figure 5.4 Load curves for NMOS and PMOS transistors of the static CMOS inverter (VDD = 2.5 V). The dots
represent the dc operation points for various input voltages.
The resulting load lines are plotted in Figure 5.4. For a dc operating points to be
valid, the currents through the NMOS and PMOS devices must be equal. Graphically, this
means that the dc points must be located at the intersection of corresponding load lines. A
number of those points (for Vin = 0, 0.5, 1, 1.5, 2, and 2.5 V) are marked on the graph. As
can be observed, all operating points are located either at the high or low output levels.
The VTC of the inverter hence exhibits a very narrow transition zone. This results from
the high gain during the switching transient, when both NMOS and PMOS are simultaneously on, and in saturation. In that operation region, a small change in the input voltage
results in a large output variation. All these observations translate into the VTC of Figure
5.5.
NMOS off
PMOS res
2.5
Vout
2
NMOS sat
PMOS res
1
1.5
NMOS sat
PMOS sat
0.5
NMOS res
PMOS sat
0.5
1
1.5
2
NMOS res
PMOS off
2.5
Vin
Figure 5.5 VTC of static CMOS inverter,
derived from Figure 5.4 (VDD = 2.5 V). For each
operation region, the modes of the transistors are
annotated — off, res(istive), or sat(urated).
Before going into the analytical details of the operation of the CMOS inverter, a
qualitative analysis of the transient behavior of the gate is appropriate as well. This
response is dominated mainly by the output capacitance of the gate, CL, which is com-
chapter5.fm Page 181 Friday, January 18, 2002 9:01 AM
Section 5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
VDD
181
VDD
Rp
Vout
Vout
CL
CL
Rn
Vin = 0
Vin = VDD
(a) Low-to-high
(b) High-to-low
Figure 5.6 Switch model of
dynamic behavior of static CMOS
inverter.
posed of the drain diffusion capacitances of the NMOS and PMOS transistors, the capacitance of the connecting wires, and the input capacitance of the fan-out gates. Assuming
temporarily that the transistors switch instantaneously, we can get an approximate idea of
the transient response by using the simplified switch model again (Figure 5.6). Let us consider the low-to-high transition first (Figure 5.6a). The gate response time is simply determined by the time it takes to charge the capacitor CL through the resistor Rp. In Example
4.5, we learned that the propagation delay of such a network is proportional to the its time
constant RpCL. Hence, a fast gate is built either by keeping the output capacitance
small or by decreasing the on-resistance of the transistor. The latter is achieved by
increasing the W/L ratio of the device. Similar considerations are valid for the high-to-low
transition (Figure 5.6b), which is dominated by the RnCL time-constant. The reader should
be aware that the on-resistance of the NMOS and PMOS transistor is not constant, but is a
nonlinear function of the voltage across the transistor. This complicates the exact determination of the propagation delay. An in-depth analysis of how to analyze and optimize the
performance of the static CMOS inverter is offered in Section 5.4.
5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
In the qualitative discussion above, the overall shape of the voltage-transfer characteristic
of the static CMOS inverter was derived, as were the values of VOH and VOL (VDD and
GND, respectively). It remains to determine the precise values of VM, VIH, and VIL as well
as the noise margins.
5.3.1
Switching Threshold
The switching threshold, VM, is defined as the point where Vin = Vout. Its value can be
obtained graphically from the intersection of the VTC with the line given by Vin = Vout
(see Figure 5.5). In this region, both PMOS and NMOS are always saturated, since VDS =
VGS. An analytical expression for VM is obtained by equating the currents through the tran-
chapter5.fm Page 182 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
182
Chapter 5
sistors. We solve the case where the supply voltage is high so that the devices can be
assumed to be velocity-saturated (or VDSAT < VM - VT). We furthermore ignore the channellength modulation effects.
V DSATp
V DSATn
- = 0
- + k p V DSATp V M – V DD – V Tp – ---------------k n V DSATn V M – V Tn – ---------------
2
2
(5.2)
Solving for VM yields
VM
V DSATp
V DSATn
V + ---------------- + r V DD + V Tp + ---------------
Tn
k p V DSATp υ satp W p
2
2
= ----------------------------------------------------------------------------------------------------- with r = --------------------- = ------------------- (5.3)
k n V DSATn υ satn W n
1+r
assuming identical oxide thicknesses for PMOS and NMOS transistors. For large values
of VDD (compared to threshold and saturation voltages), Eq. (5.3) can be simplified:
rV DD
V M ≈ -----------1+r
(5.4)
Eq. (5.4) states that the switching threshold is set by the ratio r, which compares the relative driving strengths of the PMOS and NMOS transistors. It is generally considered to be
desirable for VM to be located around the middle of the available voltage swing (or at
VDD/2), since this results in comparable values for the low and high noise margins. This
requires r to be approximately 1, which is equivalent to sizing the PMOS device so that
(W/L)p = (W/L)n × (VDSATnk′n )/(VDSATnk′p ). To move VM upwards, a larger value of r is
required, which means making the PMOS wider. Increasing the strength of the NMOS, on
the other hand, moves the switching threshold closer to GND.
From Eq. (5.2), we can derive the required ratio of PMOS versus NMOS transistor
sizes such that the switching threshold is set to a desired value VM. When using this
expression, please make sure that the assumption that both devices are velocity-saturated
still holds for the chosen operation point.
k′ n V DSATn ( V M – V Tn – V DSATn ⁄ 2 )
(W ⁄ L)
------------------p- = -------------------------------------------------------------------------------------------------( W ⁄ L )n
k′ p V DSATp ( V DD – V M + V Tp + V DSATp ⁄ 2 )
(5.5)
Problem 5.1 Inverter switching threshold for long-channel devices, or low supply-voltages.
The above expressions were derived under the assumption that the transistors are velocitysaturated. When the PMOS and NMOS are long-channel devices, or when the supply voltage is low, velocity saturation does not occur (VM-VT < VDSAT). Under these circumstances,
Eq. (5.6) holds for VM. Derive.
V Tn + r ( V DD + V Tp )
V M = ----------------------------------------------with r =
1+r
–k p
-------kn
(5.6)
chapter5.fm Page 183 Friday, January 18, 2002 9:01 AM
Section 5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
183
Design Technique — Maximizing the noise margins
When designing static CMOS circuits, it is advisable to balance the driving strengths of the
transistors by making the PMOS section wider than the NMOS section, if one wants to maximize the noise margins and obtain symmetrical characteristics. The required ratio is given by
Eq. (5.5).
Example 5.1 Switching threshold of CMOS inverter
We derive the sizes of PMOS and NMOS transistors such that the switching threshold of a
CMOS inverter, implemented in our generic 0.25 µm CMOS process, is located in the middle
between the supply rails. We use the process parameters presented in Example 3.7, and
assume a supply voltage of 2.5 V. The minimum size device has a width/length ratio of 1.5.
With the aid of Eq. (5.5), we find
–6
( W ⁄ L )p
115 × 10 × 0.63
( 1.25 – 0.43 – 0.63 ⁄ 2 -) = 3.5
------------------- = ---------------------------------- × -----------------------------------------------------–6
( 1.25 – 0.4 – 1.0 ⁄ 2 )
1.0
( W ⁄ L )n
30 × 10
Figure 5.7 plots the values of switching threshold as a function of the PMOS/NMOS
ratio, as obtained by circuit simulation. The simulated PMOS/NMOS ratio of 3.4 for a 1.25 V
switching threshold confirms the value predicted by Eq. (5.5).
An analysis of the curve of Figure 5.7 produces some interesting observations:
1. VM is relatively insensitive to variations in the device ratio. This means that small
variations of the ratio (e.g., making it 3 or 2.5) do not disturb the transfer characteristic that much. It is therefore an accepted practice in industrial designs to set the
width of the PMOS transistor to values smaller than those required for exact symmetry. For the above example, setting the ratio to 3, 2.5, and 2 yields switching
thresholds of 1.22 V, 1.18 V, and 1.13 V, respectively.
1.8
1.7
1.6
1.5
1.3
V
M
(V)
1.4
1.2
1.1
1
0.9
0.8
10
0
10
W /W
p
n
1
Figure 5.7 Simulated inverter switching
threshold versus PMOS/NMOS ratio (0.25 µm
CMOS, VDD = 2.5 V)
chapter5.fm Page 184 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
184
Vin
Chapter 5
Vmb
Vma
Vin
Vout
t
Vout
Vout
t
b) Response of inverter with
(a) Response of standard
modified threshold
inverter
Figure 5.8 Changing the inverter threshold can improve the circuit reliability.
t
2. The effect of changing the Wp/Wn ratio is to shift the transient region of the VTC.
Increasing the width of the PMOS or the NMOS moves VM towards VDD or GND
respectively. This property can be very useful, as asymmetrical transfer characteristics are actually desirable in some designs. This is demonstrated by the example of
Figure 5.8. The incoming signal Vin has a very noisy zero value. Passing this signal
through a symmetrical inverter would lead to erroneous values (Figure 5.8a). This
can be addressed by raising the threshold of the inverter, which results in a correct
response (Figure 5.8b). Further in the text, we will see other circuit instances where
inverters with asymmetrical switching thresholds are desirable.
Changing the switching threshold by a considerable amount is however not easy,
especially when the ratio of supply voltage to transistor threshold is relatively small
(2.5/0.4 = 6 for our particular example). To move the threshold to 1.5 V requires a
transistor ratio of 11, and further increases are prohibitively expensive. Observe that
Figure 5.7 is plotted in a semi-log format.
5.3.2
Noise Margins
By definition, VIH and VIL are the operational points of the inverter where
dV out
= – 1 . In
d V in
the terminology of the analog circuit designer, these are the points where the gain g of the
amplifier, formed by the inverter, is equal to −1. While it is indeed possible to derive analytical expressions for VIH and VIL, these tend to be unwieldy and provide little insight in
what parameters are instrumental in setting the noise margins.
A simpler approach is to use a piece wise linear approximation for the VTC, as
shown in Figure 5.9. The transition region is approximated by a straight line, the gain of
which equals the gain g at the switching threshold VM. The crossover with the VOH and the
VOL lines is used to define VIH and VIL points. The error introduced is small and well
chapter5.fm Page 185 Friday, January 18, 2002 9:01 AM
Section 5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
185
Vout
VOH
VM
Figure 5.9 A piece-wise linear
approximation of the VTC simplifies the
derivation of VIL and VIH.
Vin
VOL
VIL
VIH
within the range of what is required for an initial design. This approach yields the following expressions for the width of the transition region VIH - VIL, VIH, VIL, and the noise margins NMH and NML.
( V OH – V OL )
– V DD
= -----------V IH – V IL = – -----------------------------g
g
VM
V IH = V M – -----g
V DD – V M
V IL = V M + ----------------------g
NM H = V DD – V IH
(5.7)
NM L = V IL
These expressions make it increasingly clear that a high gain in the transition region is
very desirable. In the extreme case of an infinite gain, the noise margins simplify to VOH VM and VM - VOL for NMH and NML, respectively, and span the complete voltage swing.
Remains us to determine the midpoint gain of the static CMOS inverter. We assume
once again that both PMOS and NMOS are velocity-saturated. It is apparent from Figure
5.4 that the gain is a strong function of the slopes of the currents in the saturation region.
The channel-length modulation factor hence cannot be ignored in this analysis — doing so
would lead to an infinite gain. The gain can now be derived by differentiating the current
equation (5.8), valid around the switching threshold, with respect to Vin.
V DSATn
- ( 1 + λ n V out ) +
k n V DSATn V in – V Tn – ---------------
2
(5.8)
V DSATp
- ( 1 + λ p V out – λp V DD ) = 0
k p V DSATp V in – V DD – V Tp – ---------------
2
Differentiation and solving for dVout/dVin yields
dV out
k n V DSATn ( 1 + λ n Vout ) + k p V DSATp ( 1 + λ p V out – λ p VDD )
= – -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(5.9)
d V in
λ n k n V DSATn ( V in – V Tn – V DSATn ⁄ 2 ) + λ p k p V DSATp ( Vin – V DD – V Tp – V DSATp ⁄ 2 )
Ignoring some second-order terms, and setting Vin = VM results in the gain expression,
chapter5.fm Page 186 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
186
1 k n V DSATn + k p V DSATp
g = – ----------------- --------------------------------------------------ID ( VM )
λn – λp
Chapter 5
(5.10)
1+r
≈ ------------------------------------------------------------------------------( V M – V Tn – V DSATn ⁄ 2 ) ( λ n – λ p )
with ID(VM) the current flowing through the inverter for Vin = VM. The gain is almost
purely determined by technology parameters, especially the channel length modulation. It
can only in a minor way be influenced by the designer through the choice of supply and
switching threshold voltages.
Example 5.2 Voltage transfer characteristic and noise margins of CMOS Inverter
Assume an inverter in the generic 0.25 µm CMOS technology designed with a PMOS/NMOS
ratio of 3.4 and with the NMOS transistor minimum size (W = 0.375 µm, L = 0.25 µm, W/L =
1.5). We first compute the gain at VM (= 1.25 V),
I D(V M) = 1.5 × 115 × 10
–6
× 0.63 × ( 1.25 – 0.43 – 0.63 ⁄ 2 ) × ( 1 + 0.06 × 1.25 ) = 59 × 10
–6
–6
A
–6
1.5 × 115 × 10 × 0.63 + 1.5 × 3.4 × 30 × 10 × 1.0- = – 27.5 (Eq. 5.10)
1
-----------------------------------------------------------------------------------------------------------------------------g = – ---------------------–6
0.06 + 0.1
59 × 10
This yields the following values for VIL, VIH, NML, NMH:
VIL = 1.2 V, VIH = 1.3 V, NML = NMH = 1.2.
Figure 5.10 plots the simulated VTC of the inverter, as well as its derivative, the gain. A close
to ideal characteristic is obtained. The actual values of VIL and VIH are 1.03 V and 1.45 V,
respectively, which leads to noise margins of 1.03 V and 1.05 V. These values are lower than
those predicted for two reasons:
• Eq. (5.10) overestimates the gain. As observed in Figure 5.10b, the maximum gain (at
VM) equals only 17. This reduced gain would yield values for VIL and VIH of 1.17 V, and 1.33
V, respectively.
• The most important deviation is due to the piecewise linear approximation of the
VTC, which is optimistic with respect to the actual noise margins.
The obtained expressions are however perfectly useful as first-order estimations as
well as means of identifying the relevant parameters and their impact.
To conclude this example, we also extracted from simulations the output resistance of
the inverter in the low- and high-output states. Low values of 2.4 kΩ and 3.3 kΩ were
observed, respectively. The output resistance is a good measure of the sensitivity of the gate
in respect to noise induced at the output, and is preferably as low as possible.
SIDELINE: Surprisingly (or not so surprisingly), the static CMOS inverter can also be
used as an analog amplifier, as it has a fairly high gain in its transition region. This region
is very narrow however, as is apparent in the graph of Figure 5.10b. It also receives poor
marks on other amplifier properties such as supply noise rejection. Yet, this observation
can be used to demonstrate one of the major differences between analog and digital
design. Where the analog designer would bias the amplifier in the middle of the transient
region, so that a maximum linearity is obtained, the digital designer will operate the
chapter5.fm Page 187 Friday, January 18, 2002 9:01 AM
Section 5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
2.5
187
0
-2
2
-4
-6
1.5
gain
V out (V)
-8
-10
1
-12
-14
0.5
-16
0
-18
0
0.5
1
1.5
V (V)
in
Figure 5.10
= 2.5 V).
2
2.5
0
0.5
(a)
1
1.5
2
2.5
V (V)
in
(b)
Simulated Voltage Transfer Characteristic (a) and voltage gain (b) of CMOS inverter (0.25 µm CMOS, VDD
device in the regions of extreme nonlinearity, resulting in well-defined and well-separated
high and low signals.
Problem 5.2 Inverter noise margins for long-channel devices
Derive expressions for the gain and noise margins assuming that PMOS and NMOS are
long-channel devices (or that the supply voltage is low), so that velocity saturation does
not occur.
5.3.3
Robustness Revisited
Device Variations
While we design a gate for nominal operation conditions and typical device parameters,
we should always be aware that the actual operating temperature might very over a large
range, and that the device parameters after fabrication probably will deviate from the nominal values we used in our design optimization process. Fortunately, the dc-characteristics
of the static CMOS inverter turn out to be rather insensitive to these variations, and the
gate remains functional over a wide range of operating conditions. This already became
apparent in Figure 5.7, which shows that variations in the device sizes have only a minor
impact on the switching threshold of the inverter. To further confirm the assumed robustness of the gate, we have re-simulated the voltage transfer characteristic by replacing the
nominal devices by their worst- or best-case incarnations. Two corner-cases are plotted in
Figure 5.11: a better-than-expected NMOS combined with an inferior PMOS, and the
opposite scenario. Comparing the resulting curves with the nominal response shows that
the variations mostly cause a shift in the switching threshold, but that the operation of the
chapter5.fm Page 188 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
188
Chapter 5
2.5
Good PMOS
Bad NMOS
2
(V)
1.5
V
out
Nominal
1
Good NMOS
Bad PMOS
0.5
0
0
0.5
1
1.5
2
2.5
Figure 5.11 Impact of device variations on static CMOS
inverter VTC. The “good” device has a smaller oxide
thickness (- 3nm), a smaller length (-25 nm), a higher width
(+30 nm), and a smaller threshold (-60 mV). The opposite
is true for the “bad” transistor.
V (V)
in
gate is by no means affected. This robust behavior that ensures functionality of the gate
over a wide range of conditions has contributed in a big way to the popularity of the static
CMOS gate.
Scaling the Supply Voltage
In Chapter 3, we observed that continuing technology scaling forces the supply voltages to
reduce at rates similar to the device dimensions. At the same time, device threshold voltages are virtually kept constant. The reader probably wonders about the impact of this
trend on the integrity parameters of the CMOS inverter. Do inverters keep on working
when the voltages are scaled and are there potential limits to the supply scaling?
A first hint on what might happen was offered in Eq. (5.10), which indicates that the
gain of the inverter in the transition region actually increases with a reduction of the supply voltage! Note that for a fixed transistor ratio r, VM is approximately proportional to
VDD. Plotting the (normalized) VTC for different supply voltages not only confirms this
conjecture, but even shows that the inverter is well and alive for supply voltages close to
the threshold voltage of the composing transistors (Figure 5.12a). At a voltage of 0.5 V —
which is just 100 mV above the threshold of the transistors — the width of the transition
region measures only 10% of the supply voltage (for a maximum gain of 35), while it widens to 17% for 2.5 V. So, given this improvement in dc characteristics, why do we not
choose to operate all our digital circuits at these low supply voltages? Three important
arguments come to mind:
• In the following sections, we will learn that reducing the supply voltage indiscriminately has a positive impact on the energy dissipation, but is absolutely detrimental
to the performance on the gate.
• The dc-characteristic becomes increasingly sensitive to variations in the device
parameters such as the transistor threshold, once supply voltages and intrinsic voltages become comparable.
• Scaling the supply voltage means reducing the signal swing. While this typically
helps to reduce the internal noise in the system (such as caused by crosstalk), it
makes the design more sensitive to external noise sources that do not scale.
chapter5.fm Page 189 Friday, January 18, 2002 9:01 AM
Section 5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
2.5
189
0.2
2
0.15
V out (V)
V out (V)
1.5
1
0.1
0.05
0.5
gain = -1
0
0
0.5
1
1.5
2
2.5
0
0
V (V)
in
(a) Reducing VDD improves the gain...
Figure 5.12
0.05
0.1
V (V)
0.15
0.2
in
(b) but it detoriates for very-low supply voltages.
.
VTC of CMOS inverter as a function of supply voltage (0.25 µm CMOS technology).
To provide an insight into the question on potential limits to the voltage scaling, we
have plotted in Figure 5.12b the voltage transfer characteristic of the same inverter for the
even-lower supply voltages of 200 mV, 100 mV, and 50 mV (while keeping the transistor
thresholds at the same level). Amazingly enough, we still obtain an inverter characteristic,
this while the supply voltage is not even large enough to turn the transistors on! The explanation can be found in the sub-threshold operation of the transistors. The sub-threshold
currents are sufficient to switch the gate between low and high levels, and provide enough
gain to produce acceptable VTCs. The very low value of the switching currents ensures a
very slow operation but this might be acceptable for some applications (such as watches,
for example).
At around 100 mV, we start observing a major deterioration of the gate characteristic. VOL and VOH are no longer at the supply rails and the transition-region gain approaches
1. The latter turns out to be a fundamental show-stopper. To achieving sufficient gain for
use in a digital circuit, it is necessary that the supply must be at least a couple times φΤ =
kT/q (=25 mV at room temperature), the thermal voltage introduced in Chapter 3
[Swanson72]. It turns out that below this same voltage, thermal noise becomes an issue as
well, potentially resulting in unreliable operation.
kT
V DDmin > 2…4 -----q
(5.11)
Eq. (5.11) presents a true lower bound on supply scaling. It suggests that the only way to
get CMOS inverters to operate below 100 mV is to reduce the ambient temperature, or in
other words to cool the circuit.
Problem 5.3 Minimum supply voltage of CMOS inverter
Once the supply voltage drops below the threshold voltage, the transistors operate the subthreshold region, and display an exponential current-voltage relationship (as expressed in
Eq. (3.40)). Derive an expression for the gain of the inverter under these circumstances
chapter5.fm Page 190 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
190
Chapter 5
(assume symmetrical NMOS and PMOS transistors, and a maximum gain at VM = VDD/2).
The resulting expression demonstrates that the minimum voltage is a function of the slope
factor n of the transistor.
1 V DD ⁄ 2φT
– 1)
g = – --- ( e
n
(5.12)
According to this expression, the gain drops to -1 at VDD = 48 mV (for n = 1.5 and φT = 25
mV).
5.4
Performance of CMOS Inverter: The Dynamic Behavior
The qualitative analysis presented earlier concluded that the propagation delay of the
CMOS inverter is determined by the time it takes to charge and discharge the load capacitor CL through the PMOS and NMOS transistors, respectively. This observation suggests
that getting CL as small as possible is crucial to the realization of high-performance
CMOS circuits. It is hence worthwhile to first study the major components of the load
capacitance before embarking onto an in-depth analysis of the propagation delay of the
gate. In addition to this detailed analysis, the section also presents a summary of techniques that a designer might use to optimize the performance of the inverter.
5.4.1
Computing the Capacitances
Manual analysis of MOS circuits where each capacitor is considered individually is virtually impossible and is exacerbated by the many nonlinear capacitances in the MOS transistor model. To make the analysis tractable, we assume that all capacitances are lumped
together into one single capacitor CL , located between Vout and GND. Be aware that this is
a considerable simplification of the actual situation, even in the case of a simple inverter.
VDD
VDD
M2
Cg4
Cdb2
Vin
Cgd12
Vout2
Vout
Cdb1
M1
Figure 5.13
M4
Cw
Cg3
M3
Parasitic capacitances, influencing the transient behavior of the cascaded inverter pair.
chapter5.fm Page 191 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
191
Figure 5.13 shows the schematic of a cascaded inverter pair. It includes all the
capacitances influencing the transient response of node Vout. It is initially assumed that the
input Vin is driven by an ideal voltage source with zero rise and fall times. Accounting
only for capacitances connected to the output node, CL breaks down into the following
components.
Gate-Drain Capacitance Cgd12
M1 and M2 are either in cut-off or in the saturation mode during the first half (up to 50%
point) of the output transient. Under these circumstances, the only contributions to Cgd12
are the overlap capacitances of both M1 and M2. The channel capacitance of the MOS
transistors does not play a role here, as it is located either completely between gate and
bulk (cut-off) or gate and source (saturation) (see Chapter 3).
The lumped capacitor model now requires that this floating gate-drain capacitor be
replaced by a capacitance-to-ground. This is accomplished by taking the so-called Miller
effect into account. During a low-high or high-low transition, the terminals of the gatedrain capacitor are moving in opposite directions (Figure 5.14). The voltage change over
the floating capacitor is hence twice the actual output voltage swing. To present an identical load to the output node, the capacitance-to-ground must have a value that is twice as
large as the floating capacitance.
We use the following equation for the gate-drain capacitors: Cgd = 2 CGD0W (with
CGD0 the overlap capacitance per unit width as used in the SPICE model). For an in-depth
discussion of the Miller effect, please refer to textbooks such as Sedra and Smith
([Sedra87], p. 57).1
Cgd1
∆V
Vout
Vout
∆V
Vin
M1
∆V
2Cgd1
∆V
M1
Vin
Figure 5.14 The Miller effect—A capacitor experiencing identical but opposite voltage swings at both
its terminals can be replaced by a capacitor to ground, whose value is two times the original value.
Diffusion Capacitances Cdb1 and Cdb2
The capacitance between drain and bulk is due to the reverse-biased pn-junction. Such a
capacitor is, unfortunately, quite nonlinear and depends heavily on the applied voltage.
We argued in Chapter 3 that the best approach towards simplifying the analysis is to
replace the nonlinear capacitor by a linear one with the same change in charge for the voltage range of interest. A multiplication factor Keq is introduced to relate the linearized
capacitor to the value of the junction capacitance under zero-bias conditions.
1
The Miller effect discussed in this context is a simplified version of the general analog case. In a digital
inverter, the large scale gain between input and output always equals -1.
chapter5.fm Page 192 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
192
C eq = K eq C j0
Chapter 5
(5.13)
with Cj0 the junction capacitance per unit area under zero-bias conditions. An expression
for Keq was derived in Eq. (3.11) and is repeated here for convenience
– φ 0m
K eq = --------------------------------------------------- [ ( φ – V high ) 1 – m – ( φ 0 – V low ) 1 – m ]
( V high – V low ) ( 1 – m ) 0
(5.14)
with φ0 the built-in junction potential and m the grading coefficient of the junction.
Observe that the junction voltage is defined to be negative for reverse-biased junctions.
Example 5.3 Keq for a 2.5 V CMOS Inverter
Consider the inverter of Figure 5.13 designed in the generic 0.25 µm CMOS technology. The
relevant capacitance parameters for this process were summarized in Table 3.5.
Let us first analyze the NMOS transistor (Cdb1 in Figure 5.13). The propagation delay
is defined by the time between the 50% transitions of the input and the output. For the CMOS
inverter, this is the time-instance where Vout reaches 1.25 V, as the output voltage swing goes
from rail to rail or equals 2.5 V. We, therefore, linearize the junction capacitance over the
interval {2.5 V, 1.25 V} for the high-to-low transition, and {0, 1.25 V} for the low-to-high
transition.
During the high-to-low transition at the output, Vout initially equals 2.5 V. Because the
bulk of the NMOS device is connected to GND, this translates into a reverse voltage of 2.5 V
over the drain junction or Vhigh = −2.5 V. At the 50% point, Vout = 1.25 V or Vlow = −1.25 V.
Evaluating Eq. (5.14) for the bottom plate and sidewall components of the diffusion capacitance yields
Bottom plate: Keq (m = 0.5, φ0 = 0.9) = 0.57,
Sidewall: Keqsw (m = 0.44, φ0 = 0.9) = 0.61
During the low-to-high transition, Vlow and Vhigh equal 0 V and −1.25 V, respectively,
resulting in higher values for Keq,
Bottom plate: Keq (m = 0.5, φ0 = 0.9) = 0.79,
Sidewall: Keqsw (m = 0.44, φ0 = 0.9) = 0.81
The PMOS transistor displays a reverse behavior, as its substrate is connected to 2.5 V.
Hence, for the high-to-low transition (Vlow = 0, Vhigh = −1.25 V),
Bottom plate: Keq (m = 0.48, φ0 = 0.9) = 0.79,
Sidewall: Keqsw (m = 0.32, φ0 = 0.9) = 0.86
and for the low-to-high transition (Vlow = −1.25 V, Vhigh = −2.5 V)
Bottom plate: Keq (m = 0.48, φ0 = 0.9) = 0.59,
Sidewall: Keqsw (m = 0.32, φ0 = 0.9) = 0.7
Using this approach, the junction capacitance can be replaced by a linear component
and treated as any other device capacitance. The result of the linearization is a minor distortion of the voltage waveforms. The logic delays are not significantly influenced by this
simplification.
chapter5.fm Page 193 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
193
Wiring Capacitance Cw
The capacitance due to the wiring depends upon the length and width of the connecting
wires, and is a function of the distance of the fanout from the driving gate and the number
of fanout gates. As argued in Chapter 4, this component is growing in importance with the
scaling of the technology.
Gate Capacitance of Fanout Cg3 and Cg4
We assume that the fanout capacitance equals the total gate capacitance of the loading
gates M3 and M4. Hence,
C fanout = C gate ( NMOS ) + C gate ( PMOS )
= ( C GSOn + C GDOn + W n L n C ox ) + ( C GSOp + C GDOp + W p L p C ox )
(5.15)
This expression simplifies the actual situation in two ways:
• It assumes that all components of the gate capacitance are connected between Vout
and GND (or VDD), and ignores the Miller effect on the gate-drain capacitances. This
has a relatively minor effect on the accuracy, since we can safely assume that the
connecting gate does not switch before the 50% point is reached, and Vout2, therefore, remains constant in the interval of interest.
• A second approximation is that the channel capacitance of the connecting gate is
constant over the interval of interest. This is not exactly the case as we discovered in
Chapter 3. The total channel capacitance is a function of the operation mode of the
device, and varies from approximately 2/3 WLCox (saturation) to the full WLCox (linear and cut-off). A drop in overall gate capacitance also occurs just before the transistor turns on (Figure 3.30). During the first half of the transient, it may be assumed
that one of the load devices is always in linear mode, while the other transistor
evolves from the off-mode to saturation. Ignoring the capacitance variation results
in a pessimistic estimation with an error of approximately 10%, which is acceptable
for a first order analysis.
Example 5.4 Capacitances of a 0.25 µm CMOS Inverter
A minimum-size, symmetrical CMOS inverter has been designed in the 0.25 µm CMOS technology. The layout is shown in Figure 5.15. The supply voltage VDD is set to 2.5 V. From the
layout, we derive the transistor sizes, diffusion areas, and perimeters. This data is summarized
in Table 5.1. As an example, we will derive the drain area and perimeter for the NMOS transistor. The drain area is formed by the metal-diffusion contact, which has an area of 4 × 4 λ2,
and the rectangle between contact and gate, which has an area of 3 × 1 λ2. This results in a
total area of 19 λ2, or 0.30 µm2 (as λ = 0.125 µm). The perimeter of the drain area is rather
involved and consists of the following components (going counterclockwise): 5 + 4 + 4 + 1 +
1 = 15 λ or PD = 15 × 0.125 = 1.875 µm. Notice that the gate side of the drain perimeter is not
included, as this is not considered a part of the side-wall. The drain area and perimeter of the
PMOS transistor are derived similarly (the rectangular shape makes the exercise considerably
simpler): AD = 5 × 9 λ2 = 45 λ2, or 0.7 µm2; PD = 5 + 9 + 5 = 19 λ, or 2.375 µm.
chapter5.fm Page 194 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
194
Chapter 5
VDD
PMOS
(9λ/2λ)
0.25 µm = 2λ
Out
In
Metal 1
Polysilicon
NMOS
(3λ/2λ)
GND
Figure 5.15 Layout of two chained, minimum-size inverters using SCMOS Design Rules (see also
Color-plate 6).
Table 5.1
Inverter transistor data.
W/L
AD (µm2)
2
PD (µm)
AS (µm2)
2
PS (µm)
NMOS
0.375/0.25
0.3 (19 λ )
1.875 (15λ)
0.3 (19 λ )
1.875 (15λ)
PMOS
1.125/0.25
0.7 (45 λ2)
2.375 (19λ)
0.7 (45 λ2)
2.375 (19λ)
This physical information can be combined with the approximations derived above to
come up with an estimation of CL. The capacitor parameters for our generic process were
summarized in Table 3.5, and repeated here for convenience:
Overlap capacitance: CGD0(NMOS) = 0.31 fF/µm; CGDO(PMOS) = 0.27 fF/µm
Bottom junction capacitance: CJ(NMOS) = 2 fF/µm2; CJ(PMOS) = 1.9 fF/µm2
Side-wall junction capacitance: CJSW(NMOS) = 0.28 fF/µm; CJSW(PMOS) = 0.22
fF/µm
Gate capacitance: Cox(NMOS) = Cox(PMOS) = 6 fF/µm2
Finally, we should also consider the capacitance contributed by the wire, connecting
the gates and implemented in metal 1 and polysilicon. A layout extraction program typically
chapter5.fm Page 195 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
195
will deliver us precise values for this parasitic capacitance. Inspection of the layout helps us
to form a first-order estimate and yields that the metal-1 and polysilicon areas of the wire, that
are not over active diffusion, equal 42 λ2 and 72 λ2, respectively. With the aid of the interconnect parameters of Table 4.2, we find the wire capacitance — observe that we ignore the
fringing capacitance in this simple exercise. Due to the short length of the wire, this contribution is ignorable compared to the other parasitics.
Cwire = 42/82 µm2 × 30 aF/µm2 + 72/82 µm2 × 88 aF/µm2 = 0.12 fF
Bringing all the components together results in Table 5.2. We use the values of Keq
derived in Example 5.3 for the computation of the diffusion capacitances. Notice that the load
capacitance is almost evenly split between its two major components: the intrinsic capacitance, composed of diffusion and overlap capacitances, and the extrinsic load capacitance,
contributed by wire and connecting gate.
Table 5.2
5.4.2
Components of CL (for high-to-low and low-to-high transitions).
Capacitor
Expression
Value (fF) (H→L)
Value (fF) (L→H)
Cgd1
2 CGD0n Wn
0.23
0.23
Cgd2
2 CGD0p Wp
0.61
0.61
Cdb1
Keqn ADn CJ + Keqswn PDn CJSW
0.66
0.90
Cdb2
Keqp ADp CJ + Keqswp PDp CJSW)
1.5
1.15
Cg3
(CGD0n+CGSOn) Wn + Cox Wn Ln
0.76
0.76
Cg4
(CGD0p+CGSOp) Wp + Cox Wp Lp
2.28
2.28
Cw
From Extraction
0.12
0.12
CL
∑
6.1
6.0
Propagation Delay: First-Order Analysis
One way to compute the propagation delay of the inverter is to integrate the capacitor
(dis)charge current. This results in the expression of Eq. (5.16).
v2
tp =
CL ( v )
- dv
∫ ------------i(v)
(5.16)
v1
with i the (dis)charging current, v the voltage over the capacitor, and v1 and v2 the initial
and final voltage. An exact computation of this equation is intractable, as both CL(v) and
i(v) are nonlinear functions of v. We rather fall back to the simplified switch-model of the
inverter introduced in Figure 5.6 to derive a reasonable approximation of the propagation
delay adequate for manual analysis. The voltage-dependencies of the on-resistance and the
load capacitor are addressed by replacing both by a constant linear element with a value
averaged over the interval of interest. The preceding section derived precisely this value
chapter5.fm Page 196 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
196
Chapter 5
for the load capacitance. An expression for the average on-resistance of the MOS transistor was already derived in Example 3.8, and is repeated here for convenience.
1
R eq = ----------------VDD ⁄ 2
VD D
∫
V DD ⁄ 2
V
7
3 VDD
----------------------------------- dV ≈ --- ------------ 1 – --- λV DD
9
I DSAT ( 1 + λV )
4 I DSAT
(5.17)
2
V DSAT
W
with I DSAT = k' ----- ( VDD – VT )V DSAT – -------------L
2
Deriving the propagation delay of the resulting circuit is now straightforward, and is
nothing more than the analysis of a first-order linear RC-network, identical to the exercise
of Example 4.5. There, we learned that the propagation delay of such a network for a voltage step at the input is proportional to the time-constant of the network, formed by pulldown resistor and load capacitance. Hence,
t pHL = ln(2)R eqn C L = 0.69R eqn C L
(5.18)
Similarly, we can obtain the propagation delay for the low-to-high transition,
t pLH = 0.69R eqp C L
(5.19)
with Reqp the equivalent on-resistance of the PMOS transistor over the interval of interest.
This analysis assumes that the equivalent load-capacitance is identical for both the highto-low and low-to-high transitions. This has been shown to be approximately the case in
the example of the previous section. The overall propagation delay of the inverter is
defined as the average of the two values, or
t pHL + t pLH
R eqn + R eqp
t p = ------------------------- = 0.69C L -------------------------
2
2
(5.20)
Very often, it is desirable for a gate to have identical propagation delays for both rising
and falling inputs. This condition can be achieved by making the on-resistance of the
NMOS and PMOS approximately equal. Remember that this condition is identical to the
requirement for a symmetrical VTC.
Example 5.5 Propagation Delay of a 0.25 µm CMOS Inverter
To derive the propagation delays of the CMOS inverter of Figure 5.15, we make use of Eq.
(5.18) and Eq. (5.19). The load capacitance CL was already computed in Example 5.4, while
the equivalent on-resistances of the transistors for the generic 0.25 µm CMOS process were
derived in Table 3.3. For a supply voltage of 2.5 V, the normalized on-resistances of NMOS
and PMOS transistors equal 13 kΩ and 31 kΩ, respectively. From the layout, we determine
the (W/L) ratios of the transistors to be 1.5 for the NMOS, and 4.5 for the PMOS. We assume
that the difference between drawn and effective dimensions is small enough to be ignorable.
This leads to the following values for the delays:
chapter5.fm Page 197 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
197
3
Vin
2.5
Vout
2
V
out
(V)
1.5
tpHL
1
tpLH
0.5
Figure 5.16 Simulated transient
response of the inverter of Figure
5.15.
0
-0.5
0
0.5
1
1.5
2
2.5
t (sec)
x 10
-10
13kΩ- × 6.1fF = 36 psec
t pHL = 0.69 × ------------ 1.5
31kΩ
t pLH = 0.69 × -------------- × 6.0fF = 29 psec
4.5
and
36 + 29- = 32.5 psec
tp = ---------------- 2
The accuracy of this analysis is checked by performing a SPICE transient simulation
on the circuit schematic, extracted from the layout of Figure 5.15. The computed transient
response of the circuit is plotted in Figure 5.16, and determines the propagation delays to be
39.9 psec and 31.7 for the HL and LH transitions, respectively. The manual results are good
considering the many simplifications made during their derivation. Notice especially the
overshoots on the simulated output signals. These are caused by the gate-drain capacitances of
the inverter transistors, which couple the steep voltage step at the input node directly to the
output before the transistors can even start to react to the changes at the input. These overshoots clearly have a negative impact on the performance of the gate, and explain why the
simulated delays are larger than the estimations.
WARNING: This example might give the impression that manual analysis always leads
to close approximations of the actual response. This is not necessarily the case. Large
deviations can often be observed between first- and higher-order models. The purpose of
the manual analysis is to get a basic insight in the behavior of the circuit and to determine
the dominant parameters. A detailed simulation is indispensable when quantitative data is
required. Consider the example above a stroke of good luck.
chapter5.fm Page 198 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
198
Chapter 5
The obvious question a designer asks herself at this point is how she can manipulate
and/or optimize the delay of a gate. To provide an answer to this question, it is necessary
to make the parameters governing the delay explicit by expanding Req in the delay equation. Combining Eq. (5.18) and Eq. (5.17), and assuming for the time being that the channel-length modulation factor λ is ignorable, yields the following expression for tpHL (a
similar analysis holds for tpLH)
C L V DD
3 C L V DD
- = 0.52 -------------------------------------------------------------------------------------------------------t pHL = 0.69 --- ---------------( W ⁄ L ) n k′ n V DSATn ( V DD – V Tn – V DSATn ⁄ 2 )
4 I DSATn
(5.21)
In the majority of designs, the supply voltage is chosen high enough so that VDD >> VTn +
VDSATn/2. Under these conditions, the delay becomes virtually independent of the supply
voltage (Eq. (5.22)). Observe that this is a first-order approximation, and that increasing
the supply voltage yields an observable, albeit small, improvement in performance due to
a non-zero channel-length modulation factor.
CL
t pHL ≈ 0.52 ------------------------------------------( W ⁄ L ) n k′ n V DSATn
(5.22)
This analysis is confirmed in Figure 5.17, which plots the propagation delay of the
inverter as a function of the supply voltage. It comes as no surprise that this curve is virtually identical in shape to the one of Figure 3.27, which charts the equivalent on-resistance
of the MOS transistor as a function of VDD. While the delay is relative insensitive to supply variations for higher values of VDD, a sharp increase can be observed starting around
5.5
5
4.5
t p (normalized)
4
3.5
3
2.5
2
1.5
1
0.8
1
1.2
1.4
1.6
V
1.8
2
2.2
2.4
Figure 5.17 Propagation delay of CMOS
inverter as a function of supply voltage
(normalized with respect to the delay at 2.5
V). The dots indicate the delay values
predicted by Eq. (5.21). Observe that this
equation is only valid when the devices are
velocity-saturated. Hence, the deviation at
low supply voltages.
(V)
DD
≈2VT. This operation region should clearly be avoided if achieving high performance is a
premier design goal.
Design Techniques
From the above, we deduce that the propagation delay of a gate can be minimized in the following ways:
chapter5.fm Page 199 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
199
• Reduce CL. Remember that three major factors contribute to the load capacitance: the
internal diffusion capacitance of the gate itself, the interconnect capacitance, and the fanout. Careful layout helps to reduce the diffusion and interconnect capacitances. Good
design practice requires keeping the drain diffusion areas as small as possible.
• Increase the W/L ratio of the transistors. This is the most powerful and effective performance optimization tool in the hands of the designer. Proceed however with caution
when applying this approach. Increasing the transistor size also raises the diffusion
capacitance and hence CL. In fact, once the intrinsic capacitance (i.e. the diffusion capacitance) starts to dominate the extrinsic load formed by wiring and fanout, increasing the
gate size does not longer help in reducing the delay, and only makes the gate larger in
area. This effect is called “self-loading”. In addition, wide transistors have a larger gate
capacitance, which increases the fan-out factor of the driving gate and adversely affects
its speed.
• Increase VDD. As illustrated in Figure 5.17, the delay of a gate can be modulated by
modifying the supply voltage. This flexibility allows the designer to trade-off energy dissipation for performance, as we will see in a later section. However, increasing the supply voltage above a certain level yields only very minimal improvement and hence
should be avoided. Also, reliability concerns (oxide breakdown, hot-electron effects)
enforce firm upper-bounds on the supply voltage in deep sub-micron processes.
Problem 5.4
Propagation Delay as a Function of (dis)charge Current
So far, we have expressed the propagation delay as a function of the equivalent resistance of
the transistors. Another approach would be replace the transistor by a current source with
value equal to the average (dis)charge current over the interval of interest. Derive an expression of the propagation delay using this alternative approach.
5.4.3
Propagation Delay from a Design Perspective
Some interesting design considerations and trade-off’s can be derived from the delay
expressions we have derived so far. Most importantly, they lead to a general approach
towards transistor sizing that will prove to be extremely useful.
NMOS/PMOS Ratio
So far, we have consistently widened the PMOS transistor so that its resistance matches
that of the pull-down NMOS device. This typically requires a ratio of 3 to 3.5 between
PMOS and NMOS width. The motivation behind this approach is to create an inverter
with a symmetrical VTC, and to equate the high-to-low and low-to-high propagation
delays. However, this does not imply that this ratio also yields the minimum overall propagation delay. If symmetry and reduced noise margins are not of prime concern, it is actually possible to speed up the inverter by reducing the width of the PMOS device!
chapter5.fm Page 200 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
200
Chapter 5
The reasoning behind this statement is that, while widening the PMOS improves the
tpLH of the inverter by increasing the charging current, it also degrades the tpHL by cause of
a larger parasitic capacitance. When two contradictory effects are present, there must exist
a transistor ratio that optimizes the propagation delay of the inverter.
This optimum ratio can be derived through the following simple analysis. Consider
two identical, cascaded CMOS inverters. The load capacitance of the first gate equals
approximately
CL = ( C dp1 + C dn1 ) + ( C gp2 + C gn2 ) + C W
(5.23)
where Cdp1 and Cdn1 are the equivalent drain diffusion capacitances of PMOS and NMOS
transistors of the first inverter, while Cgp2 and Cgn2 are the gate capacitances of the second
gate. CW represents the wiring capacitance.
When the PMOS devices are made β times larger than the NMOS ones (β = (W/L)p /
(W/L)n), all transistor capacitances will scale in approximately the same way, or Cdp1 ≈ β
Cdn1, and Cgp2 ≈ β Cgn2. Eq. (5.23) can then be rewritten:
C L = ( 1 + β ) ( C dn1 + C gn2 ) + CW
(5.24)
An expression for the propagation delay can be derived, based on Eq. (5.20).
Reqp
0.69
t p = ---------- ( ( 1 + β ) ( C dn1 + C gn2 ) + C W ) R eqn + --------β
2
= 0.345 ( ( 1 + β ) ( Cdn1 + C gn2 ) + C W )R eqn 1 + --r-
β
(5.25)
r (= Reqp/Reqn) represents the resistance ratio of identically-sized PMOS and NMOS transistors. The optimal value of β can be found by setting
β opt =
∂tp
to 0, which yields
∂β
Cw
r 1 + ---------------------------
Cdn1 + Cgn2
(5.26)
This means that when the wiring capacitance is negligible (Cdn1+Cgn2 >> CW), βopt
equals r , in contrast to the factor r normally used in the noncascaded case. If the wiring
capacitance dominates, larger values of β should be used. The surprising result of this
analysis is that smaller device sizes (and hence smaller design area) yield a faster design at
the expense of symmetry and noise margin.
Example 5.6 Sizing of CMOS Inverter Loaded by an Identical Gate
Consider again our standard design example. From the values of the equivalent resistances
(Table 3.3), we find that a ratio β of 2.4 (= 31 kΩ / 13 kΩ) would yield a symmetrical transient response. Eq. (5.26) now predicts that the device ratio for an optimal performance
should equal 1.6. These results are verified in Figure 5.18, which plots the simulated propagation delay as a function of the transistor ratio β. The graph clearly illustrates how a changing
β trades off between tpLH and tpHL. The optimum point occurs around β = 1.9, which is some-
chapter5.fm Page 201 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
201
what higher than predicted. Observe also that the rising and falling delays are identical at the
predicted point of β equal to 2.4.
5
x 10
-11
tpLH
tpHL
tp
4
p
t (sec)
4.5
3.5
3
1
1.5
2
2.5
3
3.5
4
4.5
5
Figure 5.18 Propagation delay of CMOS inverter as a
function of the PMOS/NMOS transistor ratio β.
β
Sizing Inverters for Performance
In this analysis, we assume a symmetrical inverter, this is an inverter where PMOS and
NMOS are sized such that the rise and fall delays are identical. The load capacitance of the
inverter can be divided into an intrinsic and an extrinsic component, or CL = Cint + Cext.
Cint represents the self-loading or intrinsic output capacitance of the inverter, and is associated with the diffusion capacitances of the NMOS and PMOS transistors as well as the
gate-drain overlap (Miller) capacitances. Cext is the extrinsic load capacitance, attributable
to fanout and wiring capacitance. Assuming that Req stands for the equivalent resistance of
the gate, we can express the propagation delay as follows
t p = 0.69R eq ( C int + C ext )
= 0.69R eq C int ( 1 + C ext ⁄ C int ) = t p0 ( 1 + C ext ⁄ C int )
(5.27)
tp0 = 0.69 ReqCint represents the delay of the inverter only loaded by its own intrinsic
capacitance (Cext = 0), and is called the intrinsic or unloaded delay.
The next question is how transistor sizing impacts the performance of the gate. To
do so, we must establish the relationship between the various parameters in Eq. (5.27) and
the sizing factor S, which relates the transistor sizes of our inverter to a reference
gate—typically a minimum-sized inverter. The intrinsic capacitance Cint consists of the
diffusion and Miller capacitances, both of which are proportional to the width of the transistors. Hence, Cint = SCiref. The resistance of the gate relates to the reference gate as Req =
Rref/S. We can now rewrite Eq. (5.27),
t p = 0.69 ( R ref ⁄ S ) ( SC iref ) ( 1 + C ext ⁄ ( SC iref ) )
C ext
C ext
= 0.69R ref C iref 1 + ------------- = t p0 1 + ------------
SC iref
SC iref
(5.28)
chapter5.fm Page 202 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
202
Chapter 5
This leads to two important conclusions:
• The intrinsic delay of the inverter tp0 is independent of the sizing of the gate, and is
purely determined by technology and inverter layout. When no load is present, an
increase in the drive of the gate is totally offset by the increased capacitance.
• Making S infinitely large yields the maximum obtainable performance gain, eliminating the impact of any external load, and reducing the delay to the intrinsic one.
Yet, any sizing factor S that is sufficiently larger than (Cext/Cint) produces similar
results at a substantial gain in silicon area.
Example 5.7 Device Sizing for Performance
Let us explore the performance improvement that can be obtained by device sizing in the
design of Example 5.5. We find from Table 5.2 that Cint/Cext ≈ 1.05 (Cint = 3.0 fF, Cext = 3.15
fF). This would predict a maximum performance gain of 2.05. A scaling factor of 10 allows
us to get within 10% of this optimal performance, while larger device sizes only yield ignorable performance gains.
This is confirmed by simulation results, which predict a maximum obtainable perfor3.8
x 10
-11
3.6
3.4
p
t (sec)
3.2
3
2.8
2.6
2.4
2.2
2
2
4
6
8
S
10
12
14
Figure 5.19 Increasing inverter performance by
sizing the NMOS and PMOS transistor with an
identical factor S for a fixed fanout (inverter of
Figure 5.15).
mance improvement of 1.9 (tp0 = 19.3 psec). From the graph of Figure 5.19, we observe that
the bulk of the improvement is already obtained for S = 5, and that sizing factors larger than
10 barely yield any extra gain.
Sizing A Chain of Inverters
While sizing up an inverter reduces its delay, it also increases its input capacitance. Gate
sizing in an isolated fashion without taking into account its impact on the delay of the preceding gates is a purely academic enterprise. Therefore, a more relevant problem is determining the optimum sizing of a gate when embedded in a real environment. A simple
chain of inverters is a good first case to study. To determine the input loading effect, the
relationship between the input gate capacitance Cg and the intrinsic output capacitance of
the inverter has to be established. Both are proportional to the gate sizing. Hence, the following relationship holds, independent of gate sizing
chapter5.fm Page 203 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
203
C int = γC g
(5.29)
γ is a proportionality factor, which is only a function of technology and is close to 1 for
most sub-micron processes. Rewriting Eq. (5.28),
C ext
= t p0 ( 1 + f ⁄ γ )
t p = t p0 1 + --------γC g
(5.30)
shows that the delay if the inverter is only a function of the ratio between its external load
capacitance and input capacitance. This ratio is called the effective fanout f.
Let us consider the circuit of Eq. Figure 5.20. The goal is to minimize the delay
through the inverter chain, with the input capacitance of the first inverter Cg1—typically a
minimally-sized device— and the load capacitance CL fixed.
In
Out
Cg1
2
1
CL
N
Figure 5.20 Chain of N inverters with fixed
input and output capacitance.
Given the delay expression for the j-th inverter stage,2
C g, j + 1
t p, j = t p0 1 + --------------- = t p0 ( 1 + f j ⁄ γ )
γC g, j
(5.31)
we can derive the total delay of the chain.
N
tp =
∑t
j=1
N
p, j
= t p0
- , with C
∑ 1 + --------------γC
C g, j + 1
g, j
j=1
g, N + 1
= CL
(5.32)
This equation has N-1 unknowns, being Cg,2, Cg,3, …, Cg,N. The minimum delay can be
found by taking N-1 partial derivatives, and equating them to 0, or ∂t p ⁄ ∂C g, j = 0 . The
result is a set of constraints, Cg,j+1/Cg,j = Cg,j/Cg,j-1. In other words, the optimum size of
each inverter is the geometric mean of its neighbors sizes,
C g, j =
C g, j – 1 C g, j + 1 .
(5.33)
Overall, this means that each inverter is sized up by the same factor f with respect to the
preceding gate, has the same effective fanout (fj = f), and hence the same delay. With Cg,1
and CL given, we can derive the sizing factor,
f =
C L ⁄ C g, 1 =
F
(5.34)
t p = Nt p0 ( 1 + N F ⁄ γ ) .
(5.35)
N
N
and the minimum delay through the chain,
2
This expression ignores the wiring capacitance, which is a fair assumption for the time being.
chapter5.fm Page 204 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
204
Chapter 5
F represents the overall effective fanout of the circuit, and equals CL/Cg,1. Observe how the
relationship between tp and F is a very strong function of the number of stages. As
expected, the relationship is linear when only 1 stage is present. Introducing a second
stage turns it into square root, and so on. The obvious question now is how to choose the
number of stages so that the delay is minimized for a given value of F.
Choosing the Right Number of Stages in an Inverter Chain
Evaluation of Eq. (5.35) reveals the trade-off’s in choosing the number of stages for a
given F (=fN). When the number of stages is too large, the first component of the equation,
representing the intrinsic delay of the stages, becomes dominant. If the number of stages is
too small, the effective fanout of each stage becomes large, and the second component is
dominant. The optimum value can be found by differentiating the minimum delay expression by the number of stages, and setting the result to 0.
N F ln F
γ + N F – ------------------ = 0
N
or equivalently
f = e
(5.36)
( 1 + γ ⁄ f)
This equation only has a closed-form solution for γ = 0, this is when the self-loading is
ignored and the load capacitance only consists of the fanout. Under these simplified conditions, it is found that the optimal number of stages equals N = ln(F), and the effective
fanout of each stage is set to f = 2.71828 = e. This optimal buffer design scales consecutive
stages in an exponential fashion, and is hence called an exponential horn [Mead79]. When
self-loading is included, Eq. (5.36) can only be solved numerically. The results are plotted
in Figure 5.21a. For the typical case of γ≈1, the optimum scaler factor turns out to be close
to 3.6. Figure 5.21b plots the (normalized) propagation delay of the inverter chain as a
function of the effective fanout for γ = 1. Choosing values of the fanout that are higher
than the optimum does not impact the delay that much, and reduces the required number
of buffer stages and the implementation area. A common practice is to select an optimum
fanout of 4. The use of too many stages (f < fopt), on the other hand, has a substantial negative impact on the delay, and should be avoided.
Example 5.8 The Impact of Introducing Buffer Stages
Table 5.3 enumerates the values of tp,opt/tp0 for the unbuffered design, the dual stage, and
optimized inverter chain for a variety of values of F (for γ = 1). Observe the impressive
speed-up obtained with cascaded inverters when driving very large capacitive loads.
The above analysis can be extended to not only cover chains of inverters, but also networks of inverters that contain actual fanout, an example of which is shown in Figure
5.22. We solely have to adjusting the expression for Cext to incorporate the additional
fanout factors.
chapter5.fm Page 205 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
5
205
7
6
4.5
normalized delay
5
fopt
4
3.5
4
3
2
3
1
2.5
0
0
0.5
1
1.5
γ
2
2.5
3
1
1.5
2
2.5
3
3.5
4
4.5
5
f
(b) Normalized propagation delay (tp/(tpopt)
as a function of the effective fanout f for γ=1.
(a) Optimum effective fanout f (or inverter
scaling factor) as a function of the self-loading
factor γ in an inverter chain.
Figure 5.21 Optimizing the number of stages in an inverter chain.
Table 5.3
topt/tp0 versus x for various driver configurations.
F
Unbuffered
Two Stage
Inverter Chain
10
11
8.3
8.3
100
101
22
16.5
1000
1001
65
24.8
10,000
10,001
202
33.1
Problem 5.5 Sizing an Inverter Network
Determine the sizes of the inverters in the circuit of Figure 5.22, such that the delay
between nodes Out and In is minimized. You may assume that CL = 64 Cg,1.
In
Out
CL
1
2
3
Figure 5.22 Inverter network, in which each
gate has a fanout of 4 gates, distributing a single
input to 16 output signals in a tree-like fashion.
chapter5.fm Page 206 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
206
Chapter 5
Hints: Determine first the ratio’s between the devices that minimize the delay. You should
find that the following must hold,
4C g, 2
4C g, 3
CL
------------- = ------------= --------C g, 1
C g, 2
C g, 3
Finding the actual gate sizes (Cg,3 = 2.52Cg,2 = 6.35Cg,1) is a relatively straightforward
task. Straightforward sizing of the inverter chain, without taking the fanout into account,
would have led to a sizing factor of 4 instead of 2.52.
The rise/fall time of the input signal
All the above expressions were derived under the assumption that the input signal to the
inverter abruptly changed from 0 to VDD or vice-versa. Only one of the devices is assumed
to be on during the (dis)charging process. In reality, the input signal changes gradually
and, temporarily, PMOS and NMOS transistors conduct simultaneously. This affects the
total current available for (dis)charging and impacts the propagation delay. Figure 5.23
plots the propagation delay of a minimum-size inverter as a function of the input signal
slope—as obtained from SPICE. It can be observed that tp increases (approximately) linearly with increasing input slope, once ts > tp(ts=0).
5.4
x 10
-11
5.2
5
p
t (sec)
4.8
4.6
4.4
4.2
4
3.8
3.6
0
2
4
t (sec)
s
6
8
x 10
-11
Figure 5.23 tp as a function of the
input signal slope (10-90% rise or
fall time) for minimum-size
inverter with fan-out of a single
gate.
While it is possible to derive an analytical expression describing the relationship
between input signal slope and propagation delay, the result tends to be complex and of
limited value. From a design perspective, it is more valuable to relate the impact of the
finite slope on the performance directly to its cause, which is the limited driving capability
of the preceding gate. If the latter would be infinitely strong, its output slope would be
zero, and the performance of the gate under examination would be unaffected. The
strength of this approach is that it realizes that a gate is never designed in isolation, and
that its performance is both affected by the fanout, and the driving strength of the gate(s)
feeding into its inputs. This leads to a revised expression for the propagation delay of an
inverter i in a chain of inverters [Hedenstierna87]:
chapter5.fm Page 207 Friday, January 18, 2002 9:01 AM
Section 5.4
Performance of CMOS Inverter: The Dynamic Behavior
i
i
i–1
t p = t step + ηt step
207
(5.37)
Eq. (5.37) states that the propagation delay of inverter i equals the sum of the delay of the
i
same gate for a step input (tstep
) (i.e. zero input slope) augmented with a fraction of the
step-input delay of the preceding gate (i-1). The fraction η is an empirical constant, which
typically has values around 0.25. This expression has the advantage of being very simple,
while exposing all relationships necessary for global delay computations of complex circuits.
Example 5.9 Delay of Inverter embedded in Network
Consider for instance the circuit of Figure 5.22. With the aid of Eq. (5.31) and Eq. (5.37), we
can derive an expression for the delay of the stage-2 inverter, marked by the gray box.
4C g, 3
4C g, 2
+ ηt p0 1 + ------------t p, 2 = t p0 1 + ------------
γC g, 2
γC g, 1
An analysis of the overall propagation delay in the style of Problem 5.5, leads to the following
revised sizing requirements for minimum delay,
4 ( 1 + η )C g, 2
4 ( 1 + η )C g, 3
CL
-------------------------------- = ------------------------------- = --------C g, 1
C g, 2
C g, 3
or f2 = f1 = 2.47 (assuming η = 0.25).
Design Challenge
It is advantageous to keep the signal rise times smaller than or equal to the gate propagation
delays. This proves to be true not only for performance, but also for power consumption considerations as will be discussed later. Keeping the rise and fall times of the signals small and of
approximately equal values is one of the major challenges in high-performance design, and is
often called ‘slope engineering’.
Problem 5.6 Impact of input slope
Determine if reducing the supply voltage increases or decreases the influence of the input
signal slope on the propagation delay. Explain your answer.
Delay in the Presence of (Long) Interconnect Wires
The interconnect wire has played a minimal role in our analysis so far. When gates get farther apart, the wire capacitance and resistance can no longer be ignored, and may even
dominate the transient response. Earlier delay expressions can be adjusted to accommodate these extra contributions by employing the wire modeling techniques introduced in
chapter5.fm Page 208 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
208
Chapter 5
the previous Chapter. The analysis detailed in Example 4.9 is directly applicable to the
problem at hand. Consider the circuit of Figure 5.24, where an inverter drives a single
fanout through a wire of length L. The driver is represented by a single resistance Rdr,
which is the average between Reqn and Reqp. Cint and Cfan account for the intrinsic capacitance of the driver, and the input capacitance of the fanout gate, respectively.
(rw,cw,L)
Vout
Cint
Vout
Cfan
Figure 5.24 Inverter driving single fanout through wire of
length L.
The propagation delay of the circuit can be obtained by applying the Ellmore delay
expression.
t p = 0.69R dr C int + ( 0.69R dr + 0.38R w )C w + 0.69 ( R dr + R w )C fan
= 0.69R dr ( C int + C fan ) + 0.69 ( R dr c w + r w C fan )L + 0.38r w c w L
2
(5.38)
The 0.38 factor accounts for the fact that the wire represents a distributed delay. Cw and Rw
stand for the total capacitance and resistance of the wire, respectively. The delay expressions contains a component that is linear with the wire length, as well a quadratic one. It is
the latter that causes the wire delay to rapidly become the dominant factor in the delay
budget for longer wires.
Example 5.10 Inverter delay in presence of interconnect
Consider the circuit of Figure 5.24, and assume the device parameters of Example 5.5: Cint =
3 fF, Cfan = 3 fF, and Rdr = 0.5(13/1.5 + 31/4.5) = 7.8 kΩ. The wire is implemented in metal1
and has a width of 0.4 µm—the minimum allowed. This yields the following parameters: cw =
92 aF/µm, and rw = 0.19 Ω/µm (Example 4.4). With the aid of Eq. (5.38), we can compute at
what wire length the delay of the interconnect becomes equal to the intrinsic delay caused
purely by device parasitics. Solving the following quadratic equation yields a single (meaningful) solution.
6.6 × 10
– 18 2
L + 0.5 × 10
– 12
L = 32.29 × 10
– 12
or
L = 65 µm
Observe that the extra delay is solely due to the linear factor in the equation, and more specifically due to the extra capacitance introduced by the wire. The quadratic factor (this is, the
distributed wire delay) only becomes dominant at much larger wire lengths (> 7 cm). This is
due to the high resistance of the (minimum-size) driver transistors. A different balance
emerges when wider transistors are used. Analyze, for instance, the same problem with the
driver transistors 100 times wider, as is typical for high-speed, large fan-out drivers.
chapter5.fm Page 209 Friday, January 18, 2002 9:01 AM
Section 5.5
5.5
Power, Energy, and Energy-Delay
209
Power, Energy, and Energy-Delay
So far, we have seen that the static CMOS inverter with its almost ideal VTC—symmetrical shape, full logic swing, and high noise margins—offers a superior robustness, which
simplifies the design process considerably and opens the door for design automation.
Another major attractor for static CMOS is the almost complete absence of power consumption in steady-state operation mode. It is this combination of robustness and low
static power that has made static CMOS the technology of choice of most contemporary
digital designs. The power dissipation of a CMOS circuit is instead dominated by the
dynamic dissipation resulting from charging and discharging capacitances.
5.5.1
Dynamic Power Consumption
Dynamic Dissipation due to Charging and Discharging Capacitances
Each time the capacitor CL gets charged through the PMOS transistor, its voltage rises
from 0 to VDD, and a certain amount of energy is drawn from the power supply. Part of this
energy is dissipated in the PMOS device, while the remainder is stored on the load capacitor. During the high-to-low transition, this capacitor is discharged, and the stored energy
is dissipated in the NMOS transistor.3
A precise measure for this energy consumpVDD
tion can be derived. Let us first consider the low-tohigh transition. We assume, initially, that the input
iVDD
waveform has zero rise and fall times, or, in other
words, that the NMOS and PMOS devices are never
vout
on simultaneously. Therefore, the equivalent circuit
of Figure 5.25 is valid. The values of the energy
EVDD, taken from the supply during the transition, as
CL
well as the energy EC, stored on the capacitor at the
end of the transition, can be derived by integrating
Figure 5.25 Equivalent circuit
the instantaneous power over the period of interest.
during the low-to-high transition.
The corresponding waveforms of vout(t) and iVDD(t)
are pictured in Figure 5.26.
∞
∞
∫
∫
E VDD = i VDD ( t )V DD dt = V DD
0
0
dv out
- dt = C L V DD
C L ----------dt
VDD
∫ dv
out
2
= C L V DD
(5.39)
0
3
Observe that this model is a simplification of the actual circuit. In reality, the load capacitance consists
of multiple components some of which are located between the output node and GND, others between output
node and VDD. The latter experience a charge-discharge cycle that is out of phase with the capacitances to GND,
i.e. they get charged when Vout goes low and discharged when Vout rises. While this distributes the energy delivery by the supply over the two phases, it does not impact the overall dissipation, and the results presented in this
section are still valid.
chapter5.fm Page 210 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
210
∞
∞
∫
∫
E C = i VDD ( t )v out dt =
V DD
∫
2
C L V DD
v out dv out = ---------------2
(5.40)
0
0
vout
0
dv out
- v dt = C L
C L ----------dt out
Chapter 5
iVDD
t
Charge
Discharge
t
Figure 5.26 Output voltages and supply
current during (dis)charge of CL.
These results can also be derived by observing that during the low-to-high transition, CL is loaded with a charge CLVDD. Providing this charge requires an energy from the
supply equal to CLVDD2 (= Q × VDD). The energy stored on the capacitor equals CLVDD2/2.
This means that only half of the energy supplied by the power source is stored on CL. The
other half has been dissipated by the PMOS transistor. Notice that this energy dissipation
is independent of the size (and hence the resistance) of the PMOS device! During the discharge phase, the charge is removed from the capacitor, and its energy is dissipated in the
NMOS device. Once again, there is no dependence on the size of the device. In summary,
each switching cycle (consisting of an L→H and an H→L transition) takes a fixed amount
of energy, equal to CLVDD2. In order to compute the power consumption, we have to take
into account how often the device is switched. If the gate is switched on and off f0→1 times
per second, the power consumption equals
2
P dyn = C L V DD f 0 → 1
(5.41)
f0→1 represents the frequency of energy-consuming transitions, this is 0 → 1 transitions
for static CMOS.
Advances in technology result in ever-higher of values of f0→1 (as tp decreases). At
the same time, the total capacitance on the chip (CL) increases as more and more gates are
placed on a single die. Consider for instance a 0.25 µm CMOS chip with a clock rate of
500 Mhz and an average load capacitance of 15 fF/gate, assuming a fanout of 4. The
power consumption per gate for a 2.5 V supply then equals approximately 50 µW. For a
design with 1 million gates and assuming that a transition occurs at every clock edge, this
would result in a power consumption of 50 W! This evaluation presents, fortunately, a
pessimistic perspective. In reality, not all gates in the complete IC switch at the full rate of
500 Mhz. The actual activity in the circuit is substantially lower.
Example 5.11 Capacitive power dissipation of inverter
The capacitive dissipation of the CMOS inverter of Example 5.4 is now easily computed. In
Table 5.2, the value of the load capacitance was determined to equal 6 fF. For a supply voltage of 2.5 V, the amount of energy needed to charge and discharge that capacitance equals
chapter5.fm Page 211 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
211
2
E dyn = CL VDD = 37.5 fJ
Assume that the inverter is switched at the maximum possible rate (T = 1/f = tpLH + tpHL
= 2 tp). For a tp of 32.5 psec (Example 5.5), we find that the dynamic power dissipation of the
circuit is
P dyn = Edyn ⁄ ( 2t p ) = 580 µW
Of course, an inverter in an actual circuit is rarely switched at this maximum rate, and
even if done so, the output does not swing from rail-to-rail. The power dissipation will hence
be substantially lower. For a rate of 4 GHz (T = 250 psec), the dissipation reduces to 150 µW.
This is confirmed by simulations, which yield a power consumption of 155 µW.
Computing the dissipation of a complex circuit is complicated by the f0→1 factor,
also called the switching activity. While the switching activity is easily computed for an
inverter, it turns out to be far more complex in the case of higher-order gates and circuits.
One concern is that the switching activity of a network is a function of the nature and the
statistics of the input signals: If the input signals remain unchanged, no switching happens, and the dynamic power consumption is zero! On the other hand, rapidly changing
signals provoke plenty of switching and hence dissipation. Other factors influencing the
activity are the overall network topology and the function to be implemented. We can
accommodate this by another rewrite of the equation, or
2
2
2
P dyn = C L V DD f 0 → 1 = C L V DD P 0 → 1 f = C EFF V DD f
(5.42)
where f now presents the maximum possible event rate of the inputs (which is often the
clock rate) and P0→1 the probability that a clock event results in a 0 → 1 (or power-consuming) event at the output of the gate. CEFF = P0→1CL is called the effective capacitance
and represents the average capacitance switched every clock cycle. For our example, an
activity factor of 10% (P0→1 = 0.1) reduces the average consumption to 5 W.
Example 5.12 Switching activity
Consider the waveforms on the
right where the upper waveform
represents the idealized clock signal, and the bottom one shows the
signal at the output of the gate.
Power consuming transitions
occur 2 out of 8 times, which is
equivalent to a transition probability of 0.25 (or 25%).
Clock
Output signal
Figure 5.27 Clock and signal waveforms
Low Energy/Power Design Techniques
With the increasing complexity of the digital integrated circuits, it is anticipated that the power
problem will only worsen in future technologies. This is one of the reasons that lower supply
chapter5.fm Page 212 Friday, January 18, 2002 9:01 AM
212
THE CMOS INVERTER
Chapter 5
voltages are becoming more and more attractive. Reducing VDD has a quadratic effect on
Pdyn. For instance, reducing VDD from 2.5 V to 1.25 V for our example drops the power dissipation from 5 W to 1.25 W. This assumes that the same clock rate can be sustained. Figure 5.17
demonstrates that this assumption is not that unrealistic as long as the supply voltage is substantially higher than the threshold voltage. An important performance penalty occurs once
VDD approaches 2 VT.
When a lower bound on the supply voltage is set by external constraints (as often happens in real-world designs), or when the performance degradation due to lowering the supply
voltage is intolerable, the only means of reducing the dissipation is by lowering the effective
capacitance. This can be achieved by addressing both of its components: the physical capacitance and the switching activity.
A reduction in the switching activity can only be accomplished at the logic and architectural abstraction levels, and will be discussed in more detail in later Chapters. Lowering the
physical capacitance is an overall worthwhile goal, which also helps to improve the performance of the circuit. As most of the capacitance in a combinational logic circuit is due to transistor capacitances (gate and diffusion), it makes sense to keep those contributions to a
minimum when designing for low power. This means that transistors should be kept to minimal
size whenever possible or reasonable. This definitely affects the performance of the circuit, but
the effect can be offset by using logic or architectural speed-up techniques. The only instances
where transistors should be sized up is when the load capacitance is dominated by extrinsic
capacitances (such as fan-out or wiring capacitance). This is contrary to common design practices used in cell libraries, where transistors are generally made large to accommodate a range
of loading and performance requirements.
The above observations lead to an interesting design challenge. Assume we have to minimize the energy dissipation of a circuit with a specified lower-bound on the performance. An
attractive approach is to lower the supply voltage as much as possible, and to compensate the
loss in performance by increasing the transistor sizes. Yet, the latter causes the capacitance to
increase. It may be foreseen that at a low enough supply voltage, the latter factor may start to
dominate and cause energy to increase with a further drop in the supply voltage.
Example 5.13 Transistor Sizing for Energy Minimization
To analyze the transistor-sizing for miniIn
Out
mum energy problem, we examine the simple case of a static CMOS inverter driving an
Cext
external load capacitance Cext. To take the
Cg1
f
1
input loading effects into account, we
assume that the inverter itself is driven by a
Figure 5.28 CMOS inverter driving an external
load capacitance Cext, while being driven by a
minimum-sized device (Figure 5.28). The
minimum sized gate.
goal is to minimize the energy dissipation of
the complete circuit, while maintaining a
lower-bound on performance. The degrees of freedom are the size factor f of the inverter and
the supply voltage Vdd of the circuit. The propagation delay of the optimized circuit should
not be larger than that of a reference circuit, chosen to have as parameters f = 1 and Vdd = Vref.
Using the approach introduced in Section 5.4.3 (Sizing a Chain of Inverters), we can
derive an expression for the propagation delay of the circuit,
chapter5.fm Page 213 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
213
F
f
t p = t p0 1 + - + 1 + ----
fγ
γ
(5.43)
with F = (Cext/Cg1) the overall effective fanout of the circuit tp0 is the intrinsic delay of the
inverter. Its dependence upon VDD is approximated by the following expression, derived from
Eq. (5.21).
V DD
t p0 ∼ -----------------------V DD – V TE
(5.44)
The energy dissipation for a single transition at the input is easily found once the total capacitance of the circuit is known, or
2
E = V dd C g1 ( ( 1 + γ ) ) ( 1 + f ) + F )
(5.45)
The performance constraint now states that the propagation delay of the scaled circuit should
be equal (or smaller) to the delay of the reference circuit (f=1, Vdd = Vref). To simplify the subsequent analysis, we make the simplifying assumption that the intrinsic output capacitance of
the gate equals its gate capacitance, or γ = 1. Hence,
F
F
t p0 2 + f + ---
2 + f + ---
V DD V ref – V TE
tp
f
f
--------- = --------------------------------- = ---------- ------------------------- --------------------- = 1
V ref V DD – V TE
t p0ref ( 3 + F )
t pref
3+F
(5.46)
Eq. (5.46) establishes a relationship between the sizing factor f and the supply voltage, plotted
in Figure 5.29a for different values of F. Those curves show a clear minimum. Increasing the
size of the inverter from the minimum initially increases the performance, and hence allows
for a lowering of the supply voltage. This is fruitful until the optimum sizing factor of
f = F is reached, which should not surprise careful readers of the previous sections. Further increases in the device sizes only increase the self-loading factor, deteriorate the performance, and require an increase in supply voltage. Also observe that for the case of F=1, the
reference case is the best solution; any resizing just increases the self-loading.
4
1.5
1
F=1
3.5
3
normalized energy
2
vdd (V)
2.5
5
2
1.5
10
1
2
1
5
0.5
10
20
0.5
20
0
1
2
3
4
5
6
7
0
1
2
3
4
f
f
(a)
(b)
5
6
7
Figure 5.29 Sizing of an inverter for energy-minimization. (a) Required supply voltage as a function of the sizing factor f
for different values of the overall effective fanout F; (b) Energy of scaled circuit (normalized with respect to the reference
case) as a function of f. Vref = 2.5V, VTE = 0.5V.
chapter5.fm Page 214 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
214
Chapter 5
With the VDD(f) relationship in hand, we can derive the energy of the scaled circuit
(normalized with respect to the reference circuit) as a function of the sizing factor f.
V DD 2 2 + 2f + F
E - = --------- ------------------------------
V ref 4 + F
E ref
(5.47)
Finding an analytical expression for the optimal sizing factor is possible, but yields a complex
and messy equation. A graphical approach is just as effective. The resulting charts are plotted
in Figure 5.29b, from which a number of conclusions can be drawn:
• Device sizing, combined with supply voltage reduction, is a very effective approach in
reducing the energy consumption of a logic network. This is especially true for networks with large effective fanouts, where energy reductions with almost a factor of 10 can
be observed. But the gain is also sizable for smaller values of F. The only exception is the
F=1 case, where the minimum size device is also the most effective one.
• Oversizing the transistors beyond the optimal value comes at a hefty price in energy. This
is unfortunately a common approach in many of today’s designs.
• The optimal sizing factor for energy is smaller than the one for performance, especially for
large values of F. For example, for a fanout of 20, fopt(energy) = 3.53, while fopt(performance) = 4.47. Increasing the device sizes only leads to a minimal supply reduction once
VDD starts approaching VTE, hence leading to very minimal energy gains.
Dissipation Due to Direct-Path Currents
In actual designs, the assumption of the zero rise and fall times of the input wave forms is
not correct. The finite slope of the input signal causes a direct current path between VDD
and GND for a short period of time during switching, while the NMOS and the PMOS
transistors are conducting simultaneously. This is illustrated in Figure 5.30. Under the
(reasonable) assumption that the resulting current spikes can be approximated as triangles
and that the inverter is symmetrical in its rising and falling responses, we can compute the
energy consumed per switching period,
I peak t sc
I peak t sc
- = t sc VDD I peak
- + V DD ---------------E dp = V DD ---------------2
2
(5.48)
as well as the average power consumption
2
P dp = t sc VDD I peak f = C sc VDD f
(5.49)
The direct-path power dissipation is proportional to the switching activity, similar to the
capacitive power dissipation. tsc represents the time both devices are conducting. For a linear input slope, this time is reasonably well approximated by Eq. (5.50) where ts represents the 0-100% transition time.
chapter5.fm Page 215 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
215
VDD
VDD – VT
vin
Vin
Isc
VT
Vout
CL
t
Ipeak
ishort
t
Figure 5.30
Short-circuit currents during transients.
V DD – 2V T
V DD – 2V T t r ( f )
× -------t sc = ------------------------t s ≈ ------------------------0.8
V DD
V DD
(5.50)
Ipeak is determined by the saturation current of the devices and is hence directly proportional to the sizes of the transistors. The peak current is also a strong function of the
ratio between input and output slopes. This relationship is best illustrated by the following simple analysis: Consider a static CMOS inverter with a 0 → 1 transition at the input.
Assume first that the load capacitance is very large, so that the output fall time is significantly larger than the input rise time (Figure 5.31a). Under those circumstances, the input
VDD
VDD
ISC ≈ 0
Vin
ISC ≈ IMAX
Vout
Vin
CL
(a) Large capacitive load
Vout
CL
(b) Small capacitive load
Figure 5.31 Impact of load capacitance on short-circuit current.
moves through the transient region before the output starts to change. As the source-drain
voltage of the PMOS device is approximately 0 during that period, the device shuts off
without ever delivering any current. The short-circuit current is close to zero in this case.
Consider now the reverse case, where the output capacitance is very small, and the output
fall time is substantially smaller than the input rise time (Figure 5.31b). The drain-source
voltage of the PMOS device equals VDD for most of the transition period, guaranteeing the
maximal short-circuit current (equal to the saturation current of the PMOS). This clearly
chapter5.fm Page 216 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
216
Chapter 5
represents the worst-case condition. The conclusions of the above analysis are confirmed
in Figure 5.32, which plots the short-circuit current through the NMOS transistor during a
low-to-high transition as a function of the load capacitance.
2.5
x 10
-4
CL = 20 fF
2
CL = 100 fF
1
CL = 500 fF
I
sc
(A)
1.5
0.5
Figure 5.32 CMOS inverter short-circuit current
through NMOS transistor as a function of the load
capacitance (for a fixed input slope of 500 psec).
0
-0.5
0
2
4
time (sec)
6
x 10
-10
This analysis leads to the conclusion that the short-circuit dissipation is minimized
by making the output rise/fall time larger than the input rise/fall time. On the other hand,
making the output rise/fall time too large slows down the circuit and can cause short-circuit currents in the fan-out gates. This presents a perfect example of how local optimization and forgetting the global picture can lead to an inferior solution.
Design Techniques
A more practical rule, which optimizes the power consumption in a global way, can be formulated (Veendrick84]):
The power dissipation due to short-circuit currents is minimized by matching the rise/fall
times of the input and output signals. At the overall circuit level, this means that rise/fall
times of all signals should be kept constant within a range.
Making the input and output rise times of a gate identical is not the optimum solution for
that particular gate on its own, but keeps the overall short-circuit current within bounds. This is
shown in Figure 5.33, which plots the short-circuit energy dissipation of an inverter (normalized with respect to the zero-input rise time dissipation) as a function of the ratio r between
input and output rise/fall times. When the load capacitance is too small for a given inverter size
(r > 2…3 for VDD = 5 V), the power is dominated by the short-circuit current. For very large
capacitance values, all power dissipation is devoted to charging and discharging the load
capacitance. When the rise/fall times of inputs and outputs are equalized, most power dissipation is associated with the dynamic power and only a minor fraction (< 10%) is devoted to
short-circuit currents.
Observe also that the impact of short-circuit current is reduced when we lower the
supply voltage, as is apparent from Eq. (5.50). In the extreme case, when VDD < VTn + |VTp|,
short-circuit dissipation is completely eliminated, because both devices are never on
simultaneously. With threshold voltages scaling at a slower rate than the supply voltage, shortcircuit power dissipation is becoming of a lesser importance in deep-submicron technologies.
chapter5.fm Page 217 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
217
8
W/L|P = 1.125 µm/0.25 µm
7
W/L|N = 0.375 µm/0.25 µm
CL = 30 fF
VDD = 3.3 V
6
P norm
5
4
3
VDD = 2.5 V
2
1
0
0
VDD = 1.5 V
1
2
3
t /t
4
5
Figure 5.33 Power dissipation of a static CMOS
inverter as a function of the ratio between input
and output rise/fall times. The power is
normalized with respect to zero input rise-time
dissipation. At low values of the slope ratio, inputoutput coupling leads to some extra dissipation.
sin sout
At a supply voltage of 2.5 V and thresholds around 0.5 V, an input/output slope ratio of 2 is
needed to cause a 10% degradation in dissipation.
Finally, its is worth observing that the short-circuit power dissipation can be modeled by adding a load capacitance Csc = tscIpeak/VDD in parallel with CL, as is apparent in
Eq. (5.49). The value of this short-circuit capacitance is a function of VDD, the transistor
sizes, and the input-output slope ratio.
5.5.2
Static Consumption
The static (or steady-state) power dissipation of a circuit is expressed by Eq. (5.51), where
Istat is the current that flows between the supply rails in the absence of switching activity
P stat = I stat V DD
(5.51)
Ideally, the static current of the CMOS inverter is equal to zero, as the PMOS and
NMOS devices are never on simultaneously in steady-state operation. There is, unfortunately, a leakage current flowing through the reverse-biased diode junctions of the transistors, located between the source or drain and the substrate as shown in Figure 5.34. This
contribution is, in general, very small and can be ignored. For the device sizes under consideration, the leakage current per unit drain area typically ranges between 10-100
pA/µm2 at room temperature. For a die with 1 million gates, each with a drain area of 0.5
µm2 and operated at a supply voltage of 2.5 V, the worst-case power consumption due to
diode leakage equals 0.125 mW, which is clearly not much of an issue.
However, be aware that the junction leakage currents are caused by thermally generated carriers. Their value increases with increasing junction temperature, and this occurs
in an exponential fashion. At 85°C (a common junction temperature limit for commercial
hardware), the leakage currents increase by a factor of 60 over their room-temperature val-
chapter5.fm Page 218 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
218
Chapter 5
VDD
VDD
Vout = VDD
Drain Leakage
Current
Subthreshold current
Figure 5.34 Sources of leakage currents in
CMOS inverter (for Vin = 0 V).
ues. Keeping the overall operation temperature of a circuit low is consequently a desirable
goal. As the temperature is a strong function of the dissipated heat and its removal mechanisms, this can only be accomplished by limiting the power dissipation of the circuit
and/or by using chip packages that support efficient heat removal.
An emerging source of leakage current is the subthreshold current of the transistors.
As discussed in Chapter 3, an MOS transistor can experience a drain-source current, even
when VGS is smaller than the threshold voltage (Figure 5.35). The closer the threshold
voltage is to zero volts, the larger the leakage current at VGS = 0 V and the larger the static
power consumption. To offset this effect, the threshold voltage of the device has generally
been kept high enough. Standard processes feature VT values that are never smaller than
0.5-0.6V and that in some cases are even substantially higher (~ 0.75V).
This approach is being challenged by the reduction in supply voltages that typically
goes with deep-submicron technology scaling as became apparent in Figure 3.40. We concluded earlier (Figure 5.17) that scaling the supply voltages while keeping the threshold
voltage constant results in an important loss in performance, especially when VDD
approaches 2 VT. One approach to address this performance issue is to scale the device
thresholds down as well. This moves the curve of Figure 5.17 to the left, which means that
the performance penalty for lowering the supply voltage is reduced. Unfortunately, the
threshold voltages are lower-bounded by the amount of allowable subthreshold leakage
current, as demonstrated in Figure 5.35. The choice of the threshold voltage hence represents a trade-off between performance and static power dissipation. The continued scaling
of the supply voltage predicted for the next generations of CMOS technologies however
forces the threshold voltages ever downwards, and makes subthreshold conduction a dominant source of power dissipation. Process technologies that contain devices with sharper
turn-off characteristic will therefore become more attractive. An example of the latter is
the SOI (Silicon-on-Insulator) technology whose MOS transistors have slope-factors that
are close to the ideal 60 mV/decade.
Example 5.14 Impact of threshold reduction on performance and static power dissipation
Consider a minimum size NMOS transistor in the 0.25 µm CMOS technology. In Chapter 3,
we derived that the slope factor S for this device equals 90 mV/decade. The off-current (at
VGS = 0) of the transistor for a VT of approximately 0.5V equals 10-11A (Figure 3.22). Reducing the threshold with 200 mV to 0.3 V multiplies the off-current of the transistors with a factor of 170! Assuming a million gate design with a supply voltage of 1.5 V, this translates into
a static power dissipation of 106 ×170×10-11×1.5 = 2.6 mW. A further reduction of the thresh-
chapter5.fm Page 219 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
219
ID
VT = 0.2
VT = 0.6
VGS
Figure 5.35 Decreasing the threshold
increases the subthreshold current at VGS =
0.
old to 100 mV results in an unacceptable dissipation of almost 0.5 W! At that supply voltage,
the threshold reductions correspond to a performance improvement of 25% and 40%, respectively.
This lower bound on the thresholds is in some sense artificial. The idea that the leakage current in a static CMOS circuit has to be zero is a preconception. Certainly, the presence of leakage currents degrades the noise margins, because the logic levels are no longer
equal to the supply rails. As long as the noise margins are within range, this is not a compelling issue. The leakage currents, of course, cause an increase in static power dissipation. This is offset by the drop in supply voltage, that is enabled by the reduced thresholds
at no cost in performance, and results in a quadratic reduction in dynamic power. For a
0.25 µm CMOS process, the following circuit configurations obtain the same performance: 3 V supply–0.7 V VT; and 0.45 V supply–0.1 V VT. The dynamic power consumption of the latter is, however, 45 times smaller [Liu93]! Choosing the correct values of
supply and threshold voltages once again requires a trade-off. The optimal operation point
depends upon the activity of the circuit. In the presence of a sizable static power dissipation, it is essential that non-active modules are powered down, lest static power dissipation
would become dominant. Power-down (also called standby) can be accomplished by disconnecting the unit from the supply rails, or by lowering the supply voltage.
5.5.3
Putting It All Together
The total power consumption of the CMOS inverter is now expressed as the sum of its
three components:
2 +V
P tot = P dyn + P dp + P stat = ( C L V DD
DD I peak t s )f 0 → 1 + V DD I leak
(5.52)
In typical CMOS circuits, the capacitive dissipation is by far the dominant factor. The
direct-path consumption can be kept within bounds by careful design, and should hence
not be an issue. Leakage is ignorable at present, but this might change in the not too distant future.
chapter5.fm Page 220 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
220
Chapter 5
The Power-Delay Product, or Energy per Operation
In Chapter 1, we introduced the power-delay product (PDP) as a quality measure for a
logic gate.
(5.53)
PDP = P av t p
The PDP presents a measure of energy, as is apparent from the units (Wsec = Joule).
Assuming that the gate is switched at its maximum possible rate of fmax = 1/(2tp), and
ignoring the contributions of the static and direct-path currents to the power consumption,
we find
2
C L V DD
2
PDP = C L V DD f max t p = ---------------2
(5.54)
The PDP stands for the average energy consumed per switching event (this is, for a
0→1, or a 1→0 transition). Remember that earlier we had defined Eav as the average
energy per switching cycle (or per energy-consuming event). As each inverter cycle contains a 0→1, and a 1→0 transition, Eav hence is twice the PDP.
Energy-Delay Product
The validity of the PDP as a quality metric for a process technology or gate topology is
questionable. It measures the energy needed to switch the gate, which is an important
property for sure. Yet for a given structure, this number can be made arbitrarily low by
reducing the supply voltage. From this perspective, the optimum voltage to run the circuit
at would be the lowest possible value that still ensures functionality. This comes at the
major expense in performance, at discussed earlier. A more relevant metric should combine a measure of performance and energy. The energy-delay product (EDP) does exactly
that.
2
C L V DD
2
EDP = PDP × t p = P av t p = ---------------- tp
2
(5.55)
It is worth analyzing the voltage dependence of the EDP. Higher supply voltages reduce
delay, but harm the energy, and the opposite is true for low voltages. An optimum operation point should hence exist. Assuming that NMOS and PMOS transistors have comparable threshold and saturation voltages, we can simplify the propagation delay expression
Eq. (5.21).
αC L V DD
t p ≈ -----------------------V DD – V Te
(5.56)
where VTe = VT + VDSAT/2, and α technology parameter. Combining Eq. (5.55) and Eq.
(5.56), 4
4
This equation is only accurate as long as the devices remain in velocity saturation, which is probably
not the case for the lower supply voltages. This introduces some inaccuracy in the analysis, but will not distort
the overall result.
chapter5.fm Page 221 Friday, January 18, 2002 9:01 AM
Section 5.5
Power, Energy, and Energy-Delay
221
2
3
αC L V DD
EDP = -------------------------------2 ( V DD – V TE )
(5.57)
The optimum supply voltage can be obtained by taking the derivative of Eq. (5.57) with
respect to VDD, and equating the result to 0.
--- V TE
V DDopt = 3
2
(5.58)
The remarkable outcome from this analysis is the low value of the supply voltage
that simultaneously optimizes performance and energy. For sub-micron technologies with
thresholds in the range of 0.5 V, the optimum supply is situated around 1 V.
Example 5.15
Optimum supply voltage for 0.25 µm CMOS inverter
From the technology parameters for our generic CMOS process presented in Chapter 3, the
value of VTE can be derived.
VTn = 0.43 V, VDsatn = 0.63 V, VTEn = 0.74 V.
VTp = -0.4 V, VDsatp = -1 V, VTEp = -0.9 V.
VTE ≈ (VTEn+|VTEp|)/2 = 0.8 V
Hence, VDDopt = (3/2) × 0.8 V = 1.2 V. The simulated graphs of Figure 5.36, plotting normalized delay, energy, and energy-delay product, confirm this result. The optimum supply voltage is predicted to equal 1.1 V. The charts clearly illustrate the trade-off between delay and
energy.
15
Energy-Delay (norm)
Energy-Delay
10
Energy
Delay
5
0
0.5
1
1.5
V (V)
2
2.5
Figure 5.36 Normalized delay, energy,
and energy-delay plots for CMOS inverter in
0.25 µm CMOS technology.
DD
WARNING: While the above example demonstrates that there exists a supply voltage
that minimizes the energy-delay product of a gate, this voltage does not necessarily represent the optimum voltage for a given design problem. For instance, some designs require a
minimum performance, which requires a higher voltage at the expense of energy. Similarly, a lower-energy design is possible by operating by circuit at a lower voltage and by
chapter5.fm Page 222 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
222
Chapter 5
obtaining the overall system performance through the use of architectural techniques such
as pipelining or concurrency.
5.5.4
Analyzing Power Consumption Using SPICE
A definition of the average power consumption of a circuit was provided in Chapter 1, and
is repeated here for the sake of convenience.
P av
T
T
∫
∫
V DD
1
- i DD ( t )dt
= --- p ( t )dt = --------T
T
0
(5.59)
0
with T the period of interest, and VDD and iDD the supply voltage and current, respectively.
Some implementations of SPICE provide built-in functions to measure the average value
of a circuit signal. For instance, the HSPICE .MEASURE TRAN I(VDD) AVG command
computes the area under a computed transient response (I(VDD)) and divides it by the
period of interest. This is identical to the definition given in Eq. (5.59). Other implementations of SPICE are, unfortunately, not as extensive. This is not as bad as it seems, as long
as one realizes that SPICE is actually a differential equation solver. A small circuit can
easily be conceived that acts as an integrator and whose output signal is nothing but the
average power.
Consider, for instance, the circuit of Figure 5.37. The current delivered by the power
supply is measured by the current-controlled current source and integrated on the capacitor C. The resistance R is only provided for DC-convergence reasons and should be chosen as high as possible to minimize leakage. A clever choice of the element parameter
ensures that the output voltage Pav equals the average power consumption. The operation
of the circuit is summarized in Eq. (5.60) under the assumption that the initial voltage on
the capacitor C is zero.
C
dP av
= ki DD
dt
or
(5.60)
T
∫
k- i dt
P av = --C DD
0
Equating Eq. (5.59) and Eq. (5.60) yields the necessary conditions for the equivalent
circuit parameters: k/C = VDD/T. Under these circumstances, the equivalent circuit shown
presents a convenient means of tracking the average power in a digital circuit.
Example 5.16 Average Power of Inverter
The average power consumption of the inverter of Example 5.4 is analyzed using the above
technique for a toggle period of 250 psec (T = 250 psec, k = 1, VDD = 2.5 V, hence C = 100
pF). The resulting power consumption is plotted in Figure 5.38, showing an average power
consumption of approximately 157.3 µW. The .MEAS AVG command yields a value of
chapter5.fm Page 223 Friday, January 18, 2002 9:01 AM
Section 5.6
Perspective: Technology Scaling and its Impact on the Inverter Metrics
223
VDD
Pav
+
iDD
C
Circuit
under test
–
k iDD
R
Figure 5.37 Equivalent circuit to measure average power in SPICE.
160.32 µW, which demonstrates the approximate equivalence of both methods. These numbers are equivalent to an energy of 39 fJ (which is close to the 37.5 fJ derived in Example
5.11). Observe the slightly negative dip during the high-to-low transition. This is due to the
injection of current into the supply, when the output briefly overshoots VDD as a result of the
capacitive coupling between input and output (as is apparent from in the transient response of
Figure 5.16).
1.8
x 10
-4
Average Power
(over one cycle)
1.6
1.4
power (W)
1.2
Vin: 0→1
1
0.8
0.6
0.4
0.2
0
0
0.5
1
1.5
2
t (sec)
5.6
2.5
x 10
-10
Figure 5.38 Deriving the power
consumption using SPICE.
Perspective: Technology Scaling and its Impact on the Inverter
Metrics
In section 3.5, we have explored the impact of the scaling of technology on the some of
the important design parameters such as area, delay, and power. For the sake of clarity, we
repeat here some of the most important entries in the resulting scaling table (Table 3.8).
Table 5.4 Scaling scenarios for short-channel devices (S and U represent the technology and voltage
scaling parameters, respectively).
Parameter
Relation
Full Scaling
General Scaling
Fixed-Voltage Scaling
Area/Device
WL
1/S2
1/S2
1/S2
Intrinsic Delay
RonCgate
1/S
1/S
1/S
chapter5.fm Page 224 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
224
Chapter 5
Table 5.4 Scaling scenarios for short-channel devices (S and U represent the technology and voltage
scaling parameters, respectively).
Parameter
Relation
Full Scaling
General Scaling
Fixed-Voltage Scaling
Intrinsic Energy
CgateV2
1/S3
1/SU2
1/S
Intrinsic Power
Energy/Delay
1/S
Power Density
P/Area
1
2
2
1
S2/U2
S2
1/U
To validity of these theoretical projections can be verified by looking back and
observing the trends during the past decades.
From Figure 5.39, we can derive that the gate
delay indeed decreases exponentially at a rate
of 13%/year, or halving every five years. This
rate is on course with the prediction of Table
5.4, since S averages approximately 1.15 as
we had already observed in Figure 3.39. The
delay of a 2-input NAND gate with a fanout of
four has gone from tens of nanoseconds in the
1960s to a tenth of a nanosecond in the year Figure 5.39 Scaling of the gate delay (from
2000, and is projected to be a few tens of pico- [Dally98]).
seconds by 2010.
Reducing power dissipation has only been a second-order priority until recently.
Hence, statistics on dissipation-per-gate or design are only marginally available. An interesting chart is shown in Figure 5.40, which plots the power density measured over a large
number of designs produced between 1980 and 1995. Although the variation is
large—even for a fixed technology—it shows the power density to increase approximately
with S2. This is in correspondence with the fixed-voltage scaling scenario presented in
Table 5.4. For more recent years, we expect a scenario more in line with the full-scaling
model—which predicts a constant power density—due to the accelerated supply-voltage
scaling and the increased attention to power-reducing design techniques. Even under these
circumstances, power dissipation-per-chip will continue to increase due to the ever-larger
die sizes.
The presented scaling model has one fatal flaw however: the performance and
power predictions produce purely “intrinsic” numbers that take only device parameters
into account. In Chapter 4, it was concluded that the interconnect wires exhibit a different
scaling behavior, and that wire parasitics may come to dominate the overall performance.
Similarly, charging and discharging the wire capacitances may dominate the energy budget. To get a crisper perspective, one has to construct a combined model that considers
device and wire scaling models simultaneously. The impact of the wire capacitance and its
scaling behavior is summarized in Table 5.5. We adopt the fixed-resistance model introduced in Chapter 4. We furthermore assume that the resistance of the driver dominates the
wire resistance, which is definitely the case for short to medium-long wires.
chapter5.fm Page 225 Friday, January 18, 2002 9:01 AM
Section 5.6
Perspective: Technology Scaling and its Impact on the Inverter Metrics
225
∝ S2
Figure 5.40 Evolution of power-density in
micro- and DSP processors, as a function of
the scaling factor S ([Sakurai97]). S is
normalized to 1 for a 4 µm process.
S
Table 5.5 Scaling scenarios for wire capacitance. S and U represent the technology and voltage scaling
parameters, respectively, while SL stands for the wire-length scaling factor. εc represents the impact of fringing
and inter-wire capacitances.
Parameter
Relation
General Scaling
Wire Capacitance
WL/t
εc/SL
Wire Delay
RonCint
εc/SL
Wire Energy
CintV2
εc/SLU2
Wire Delay / Intrinsic Delay
εcS/SL
Wire Energy / Intrinsic Energy
εcS/SL
The model predicts that the interconnect-caused delay (and energy) gain in importance with the scaling of technology. This impact is limited to an increase with εc for short
wires (S = SL), but it becomes increasingly more outspoken for medium-range and long
wires (SL < S). These conclusions have been confirmed by a number of studies, an example of which is shown in Figure 5.41. How the ratio of wire over intrinsic contributions
will actually evolve is debatable, as it depends upon a wide range of independent parameters such as system architecture, design methodology, transistor sizing, and interconnect
materials. The doom-day scenario that interconnect may cause CMOS performance to saturate in the very near future hence may be exaggerated. Yet, it is clear to that increased
attention to interconnect is an absolute necessity, and may change the way the next-generation circuits are designed and optimized (e.g. [Sylvester99]).
chapter5.fm Page 226 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
226
Chapter 5
Figure 5.41 Evolution of wire delay / gate delay ratio
with respect to technology (from [Fisher98]).
5.7
Summary
This chapter presented a rigorous and in-depth analysis of the static CMOS inverter. The
key characteristics of the gate are summarized:
• The static CMOS inverter combines a pull-up PMOS section with a pull-down
NMOS device. The PMOS is normally made wider than the NMOS due to its inferior current-driving capabilities.
• The gate has an almost ideal voltage-transfer characteristic. The logic swing is equal
to the supply voltage and is not a function of the transistor sizes. The noise margins
of a symmetrical inverter (where PMOS and NMOS transistor have equal currentdriving strength) approach VDD/2. The steady-state response is not affected by fanout.
• Its propagation delay is dominated by the time it takes to charge or discharge the
load capacitor CL. To a first order, it can be approximated as
R eqn + R eqp
t p = 0.69C L -------------------------
2
Keeping the load capacitance small is the most effective means of implementing
high-performance circuits. Transistor sizing may help to improve performance as
long as the delay is dominated by the extrinsic (or load) capacitance of fanout and
wiring.
• The power dissipation is dominated by the dynamic power consumed in charging
and discharging the load capacitor. It is given by P0→1 CLVDD2f. The dissipation is
proportional to the activity in the network. The dissipation due to the direct-path
currents occurring during switching can be limited by careful tailoring of the signal
chapter5.fm Page 227 Friday, January 18, 2002 9:01 AM
Section 5.8
To Probe Further
227
slopes. The static dissipation can usually be ignored but might become a major factor in the future as a result of subthreshold currents.
• Scaling the technology is an effective means of reducing the area, propagation delay
and power consumption of a gate. The impact is even more striking if the supply
voltage is scaled simultaneously.
• The interconnect component is gradually taking a larger fraction of the delay and
performance budget.
5.8
To Probe Further
The operation of the CMOS inverter has been the topic of numerous publications and textbooks. Virtually every book on digital design devotes a substantial number of pages to the
analysis of the basic inverter gate. An extensive list of references was presented in Chapter
1. Some references of particular interest that were explicitly quoted in this chapter are
given below.
REFERENCES
[Dally98] W. Dally and J. Poulton, Digital Systems Engineering, Cambridge University Press, 1998.
[Fisher98] P. D. Fisher and R. Nesbitt, ``The Test of Time: Clock-Cycle Estimation and Test Challenges for Future Microprocessors,'' IEEE Circuits and Devices Magazine, 14(2), pp. 37-44,
1998.
[Hedenstierna87] N. Hedenstierna and K. Jeppson, “CMOS Circuit Speed and Buffer Optimization,” IEEE Transactions on CAD, Vol CAD-6, No 2, pp. 270-281, March 1987.
[Liu93] D. Liu and C Svensson, “Trading speed for low power by choice of supply and threshold
voltages”, IEEE Journal of Solid State Circuits, Vol.28, no.1, pp. 10-17, Jan. 1993, p.10-17.
[Mead80] C. Mead and L. Conway, Introduction to VLSI Systems, Addison-Wesley, 1980.
[Sakurai97] T.Sakurai, H.Kawaguchi, T.Kuroda, “Low-Power CMOS Design through VTH Control
and Low-Swing Circuits,” Digest International Symp.on Low-Power Electronics and Design,
pp.1-6, Sept. 1997. Also in T.Sakurai, T.Kuroda, “Low Voltage Technology and Circuits,” Mead
Microelectronics Conference, Lausanne, Switzerland, June 1997.
[Sedra87] Sedra and Smith, MicroElectronic Circuits, Holt, Rinehart and Winston, 1987.
[Swanson72] R. Swanson and J. Meindl, “Ion-Implanted Complementary CMOS transistors in LowVoltage Circuits,” IEEE Journal of Solid-State Circuits, Vol. SC-7, No. 2, pp.146-152, April
1972.
[Veendrick84] H. Veendrick, “Short-Circuit Dissipation of Static CMOS Circuitry and its Impact on
the Design of Buffer Circuits,” IEEE Journal of Solid-State Circuits, Vol. SC-19, no. 4,
pp. 468–473, 1984.
chapter5.fm Page 228 Friday, January 18, 2002 9:01 AM
THE CMOS INVERTER
228
5.9
Chapter 5
Exercises and Design Problems
For all problems, use the device parameters provided in Chapter 3 (as well as the inside back cover),
unless otherwise mentioned.
DESIGN PROBLEM
Using the 1.2 µm CMOS introduced in Chapter 2, design a static CMOS
inverter that meets the following requirements:
1. Matched pull-up and pull-down times (i.e., tpHL = tpLH).
2. tp = 5 nsec (± 0.1 nsec).
The load capacitance connected to the output is equal to 4 pF. Notice that this
capacitance is substantially larger than the internal capacitances of the gate.
Determine the W and L of the transistors. To reduce the parasitics, use
minimal lengths (L = 1.2 µm) for all transistors. Verify and optimize the design
using SPICE after proposing a first design using manual computations. Compute also the energy consumed per transition. If you have a layout editor (such
as MAGIC) available, perform the physical design, extract the real circuit
parameters, and compare the simulated results with the ones obtained earlier.
CHAPTER
6
DESIGNING COMBINATIONAL
LOGIC GATES IN CMOS
In-depth discussion of logic families in CMOS—
static and dynamic, pass-transistor, non-ratioed and ratioed logic
n
Optimizing a logic gate for area, speed, energy, or robustness
n
Low-power and high-performance circuit-design techniques
6.1
6.2
6.3
Introduction
6.3.3
Issues in Dynamic Design
Static CMOS Design
6.3.4
Cascading Dynamic Gates
6.2.1
Complementary CMOS
6.4
6.2.2
Ratioed Logic
6.4.1
How to Choose a Logic Style?
6.2.3
Pass-Transistor Logic
6.4.2
Designing Logic for Reduced Supply
Voltages
Dynamic CMOS Design
Perspectives
6.3.1
Dynamic Logic: Basic Principles
6.5
Summary
6.3.2
Speed and Power Dissipation of
Dynamic Logic
6.6
To Probe Further
229
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
230
6.1
Chapter 6
Introduction
The design considerations for a simple inverter circuit were presented in the previous
chapter. Now, we will extend this discussion to address the synthesis of arbitrary digital
gates such as NOR, NAND and XOR. The focus is on combinational logic (or non-regenerative) circuits; this is, circuits that have the property that at any point in time, the output
of the circuit is related to its current input signals by some Boolean expression (assuming
that the transients through the logic gates have settled). No intentional connection between
outputs and inputs is present.
This is in contrast to another class of circuits, known as sequential or regenerative,
for which the output is not only a function of the current input data, but also of previous
values of the input signals (Figure 6.1). This is accomplished by connecting one or more
outputs intentionally back to some inputs. Consequently, the circuit “remembers” past
events and has a sense of history. A sequential circuit includes a combinational logic portion and a module that holds the state. Example circuits are registers, counters, oscillators,
and memory. Sequential circuits are the topic of the next Chapter.
In
Combinational
Logic
Circuit
In
Out
Combinational
Logic
Circuit
Out
State
(a) Combinational
(b) Sequential
Figure 6.1 High level classification of logic circuits.
There are numerous circuit styles to implement a given logic function. As with the
inverter, the common design metrics by which a gate is evaluated are area, speed, energy
and power. Depending on the application, the emphasis will be on different metrics. For
instance, the switching speed of digital circuits is the primary metric in a high-performance processor, while it is energy dissipation in a battery operated circuit. In addition to
these metrics, robustness to noise and reliability are also very important considerations.
We will see that certain logic styles can significantly improve performance, but are more
sensitive to noise. Recently, power dissipation has also become a very important requirement and significant emphasis is placed on understanding the sources of power and
approaches to deal with power.
6.2
Static CMOS Design
The most widely used logic style is static complementary CMOS. The static CMOS style
is really an extension of the static CMOS inverter to multiple inputs. In review, the primary advantage of the CMOS structure is robustness (i.e, low sensitivity to noise), good
performance, and low power consumption with no static power dissipation. Most of those
Section 6.2
Static CMOS Design
231
properties are carried over to large fan-in logic gates implemented using a similar circuit
topology.
The complementary CMOS circuit style falls under a broad class of logic circuits
called static circuits in which at every point in time (except during the switching transients), each gate output is connected to either VDD or Vss via a low-resistance path. Also,
the outputs of the gates assume at all times the value of the Boolean function implemented
by the circuit (ignoring, once again, the transient effects during switching periods). This is
in contrast to the dynamic circuit class, which relies on temporary storage of signal values
on the capacitance of high-impedance circuit nodes. The latter approach has the advantage
that the resulting gate is simpler and faster. Its design and operation are however more
involved and prone to failure due to an increased sensitivity to noise.
In this section, we sequentially address the design of various static circuit flavors
including complementary CMOS, ratioed logic (pseudo-NMOS and DCVSL), and passtransistor logic. The issues of scaling to lower power supply voltages and threshold voltages will also be dealt with.
6.2.1
Complementary CMOS
Concept
A static CMOS gate is a combination of two networks, called the pull-up network (PUN)
and the pull-down network (PDN) (Figure 6.2). The figure shows a generic N input logic
gate where all inputs are distributed to both the pull-up and pull-down networks. The function of the PUN is to provide a connection between the output and VDD anytime the output
of the logic gate is meant to be 1 (based on the inputs). Similarly, the function of the PDN
is to connect the output to VSS when the output of the logic gate is meant to be 0. The PUN
and PDN networks are constructed in a mutually exclusive fashion such that one and only
one of the networks is conducting in steady state. In this way, once the transients have settled, a path always exists between VDD and the output F, realizing a high output (“one”),
or, alternatively, between VSS and F for a low output (“zero”). This is equivalent to stating
that the output node is always a low-impedance node in steady state.
VDD
In1
In2
PUN
InN
pull-up: make a connection from VDD to F when
F(In1,In2, ... Inn) = 1
F (In1,In2, ... Inn)
In1
In2
PDN
InN
pull-down: make a connection from VDD to Vss when
F(In1,In2, ... Inn) = 0
VSS
Figure 6.2 Complementary logic gate as a combination of a PUN (pull-up network) and a
PDN (pull-down network).
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
232
Chapter 6
In constructing the PDN and PUN networks, the following observations should be
kept in mind:
• A transistor can be thought of as a switch controlled by its gate signal. An NMOS
switch is on when the controlling signal is high and is off when the controlling signal
is low. A PMOS transistor acts as an inverse switch that is on when the controlling
signal is low and off when the controlling signal is high.
• The PDN is constructed using NMOS devices, while PMOS transistors are used in
the PUN. The primary reason for this choice is that NMOS transistors produce
“strong zeros,” and PMOS devices generate “strong ones”. To illustrate this, consider the examples shown in Figure 6.3. In Figure 6.3a, the output capacitance is initially charged to VDD. Two possible discharge scenarios are shown. An NMOS
device pulls the output all the way down to GND, while a PMOS lowers the output
no further than |VTp| — the PMOS turns off at that point, and stops contributing discharge current. NMOS transistors are hence the preferred devices in the PDN. Similarly, two alternative approaches to charging up a capacitor are shown in Figure
6.3b, with the output initially at GND. A PMOS switch succeeds in charging the
output all the way to VDD, while the NMOS device fails to raise the output above
VDD-VTn. This explains why PMOS transistors are preferentially used in a PUN.
Out
VDD
VDD→ 0
Out
VDD→ |VTp|
CL
CL
(a) pulling down a node using NMOS and PMOS switches
VDD
0 → VDD
0→ VDD- VTn
Figure 6.3 Simple examples
illustrate why an NMOS should be
used as a pull-down, and a PMOS
should be used as a pull-up device.
Out
Out
CL
CL
(b) pulling down a node using NMOS and PMOS switches
• A set of construction rules can be derived to construct logic functions (Figure 6.4).
NMOS devices connected in series corresponds to an AND function. With all the
inputs high, the series combination conducts and the value at one end of the chain is
transferred to the other end. Similarly, NMOS transistors connected in parallel represent an OR function. A conducting path exists between the output and input terminal if at least one of the inputs is high. Using similar arguments, construction rules
for PMOS networks can be formulated. A series connection of PMOS conducts if
both inputs are low, representing a NOR function (A.B = A+B), while PMOS transistors in parallel implement a NAND (A+B = A·B.
• Using De Morgan’s theorems ((A + B) = A·B and A·B = A + B), it can be shown that
the pull-up and pull-down networks of a complementary CMOS structure are dual
networks. This means that a parallel connection of transistors in the pull-up network
corresponds to a series connection of the corresponding devices in the pull-down
Section 6.2
Static CMOS Design
A
B
Series Combination
233
A
Conducts if A · B
(a) series
Parallel Combination
Conducts if A + B
B
(b) parallel
Figure 6.4 NMOS logic rules — series devices implement an AND, and parallel devices
implement an OR.
network, and vice versa. Therefore, to construct a CMOS gate, one of the networks
(e.g., PDN) is implemented using combinations of series and parallel devices. The
other network (i.e., PUN) is obtained using duality principle by walking the hierarchy, replacing series sub-nets with parallel sub-nets, and parallel sub-nets with
series sub-nets. The complete CMOS gate is constructed by combining the PDN
with the PUN.
• The complementary gate is naturally inverting, implementing only functions such as
NAND, NOR, and XNOR. The realization of a non-inverting Boolean function
(such as AND OR, or XOR) in a single stage is not possible, and requires the addition of an extra inverter stage.
• The number of transistors required to implement an N-input logic gate is 2N.
Example 6.1 Two-input NAND Gate
Figure 6.5 shows a two-input NAND gate (F = A·B). The PDN network consists of two
NMOS devices in series that conduct when both A and B are high. The PUN is the dual network, and consists of two parallel PMOS transistors. This means that F is 1 if A = 0 or B = 0,
which is equivalent to F = A·B. The truth table for the simple two input NAND gate is given
in Table 6.1. It can be verified that the output F is always connected to either VDD or GND,
but never to both at the same time.
VDD
Table 6.1Truth Table for 2 input NAND
A
B
F
A
A
B
F
0
0
1
0
1
1
1
0
1
1
1
0
B
Figure 6.5 Two-input NAND gate in complementary static CMOS style.
Example 6.2 Synthesis of complex CMOS Gate
Using complementary CMOS logic, consider the synthesis of a complex CMOS gate whose
function is F = D + A· (B +C). The first step in the synthesis of the logic gate is to derive the
pull-down network as shown in Figure 6.6a by using the fact that NMOS devices in series
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
234
Chapter 6
implements the AND function and parallel device implements the OR function. The next step
is to use duality to derive the PUN in a hierarchical fashion. The PDN network is broken into
smaller networks (i.e., subset of the PDN) called sub-nets that simplify the derivation of the
PUN. In Figure 6.6b, the sub-nets (SN) for the pull-down network are identified At the top
level, SN1 and SN2 are in parallel so in the dual network, they will be in series. Since SN1
consists of a single transistor, it maps directly to the pull-up network. On the other hand, we
need to recursively apply the duality rules to SN2. Inside SN2, we have SN3 and SN4 in
series so in the PUN they will appear in parallel. Finally, inside SN3, the devices are in parallel so they appear in series in the PUN. The complete gate is shown in Figure 6.6c. The reader
can verify that for every possible input combination, there always exists a path to either VDD
or GND.
VDD
VDD
C
SN1
D
D
B
C
B
SN2
A
A
A
SN4
F
F
SN3
B
D
C
F
(a) pull-down network
(b) Deriving the pull-up network
hierarchically by identifying
sub-nets
A
D
B
C
Figure 6.6 Complex complementary CMOS gate.
(c) complete gate
Static Properties of Complementary CMOS Gates
Complementary CMOS gates inherit all the nice properties of the basic CMOS inverter.
They exhibit rail to rail swing with VOH = VDD and VOL = GND. The circuits also have no
static power dissipation, since the circuits are designed such that the pull-down and pullup networks are mutually exclusive. The analysis of the DC voltage transfer characteristics and the noise margins is more complicated then for the inverter, as these parameters
depend upon the data input patterns applied to gate.
Consider the static two-input NAND gate shown in Figure 6.7. Three possible input
combinations switch the output of the gate from high-to-low: (a) A = B = 0 → 1, (b) A= 1,
B = 0 → 1, and (c) B= 1, A = 0 → 1. The resulting voltage transfer curves display significant differences. The large variation between case (a) and the others (b & c) is explained
by the fact that in the former case both transistors in the pull-up network are on simultaneously for A=B=0, representing a strong pull-up. In the latter cases, only one of the pullup devices is on. The VTC is shifted to the left as a result of the weaker PUN.
The difference between (b) and (c) results mainly from the state of the internal node
int between the two NMOS devices. For the NMOS devices to turn on, both gate-tosource voltages must be above VTn, with VGS2 = VA - VDS1 and VGS1 = VB. The threshold
Section 6.2
Static CMOS Design
235
3.0
VDD
A
M3
B
M4
A = B = 0→1
F
A
M2
Vout, V
2.0
1.0
int
B
A=1, B=0→1
B=1, A=0→1
M1
0.00.0
1.0
2.0
3.0
Vin, V
Figure 6.7 The VTC of a two-input NAND is data-dependent. NMOS devices are
0.5µm/0.25µm while the PMOS devices are sized at 0.75µm/0.25µm.
voltage of transistor M2 will be higher than transistor M1 due to the body effect. The
threshold voltages of the two devices are given by:
V Tn2 = V tn0 + γ ( (
2φ f + Vint ) –
VTn1 = V tn0
2φ f )
(6.1)
(6.2)
For case (b), M3 is turned off, and the gate voltage of M2 is set to VDD. To a first
order, M2 may be considered as a resistor in series with M1. Since the drive on M2 is large,
this resistance is small and has only a small effect on the voltage transfer characteristics.
In case (c), transistor M1 acts as a resistor, causing body effect in M2. The overall impact
is quite small as seen from the plot.
Design Consideration
The important point to take away from the above discussion is that the noise margins are
input-pattern dependent. For the above example, a glitch on only one of the two inputs has a
larger chance of creating a false transition at the output than when the glitch would occur on
both inputs simultaneously. Therefore, the former condition has a lower low noise margin. A
common practice when characterizing gates such as NAND and NOR is to connect all the
inputs together. This unfortunately does not represent the worst-case static behavior. The data
dependencies should be carefully modeled.
Propagation Delay of Complementary CMOS Gates
The computation of propagation delay proceeds in a fashion similar to the static inverter.
For the purpose of delay analysis, each transistor is modeled as a resistor in series with an
ideal switch. The value of the resistance is dependent on the power supply voltage and an
equivalent large signal resistance, scaled by the ratio of device width over length, must be
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
236
Chapter 6
used. The logic is transformed into an equivalent RC network that includes the effect of
internal node capacitances. Figure 6.8 shows the two-input NAND gate and its equivalent
RC switch level model. Note that the internal node capacitance Cint —attributable to the
source/drain regions and the gate overlap capacitance of M2/M1— is included. While complicating the analysis, the capacitance of the internal nodes can have quite an impact in
some networks such as large fan-in gates. In a first pass, we ignore the effect of the internal capacitance.
VDD
VDD
A
M3
RP
B
M4
F
A
M2
B
M1
A
RP
B
F
RN
CL
A
Figure 6.8 Equivalent RC
model for a 2-input NAND gate.
RN
(a) Two-input NAND
Cint
B
(b) RC equivalent model
A simple analysis of the model shows that—similar to the noise margins—the
propagation delay depends upon the input patterns. Consider for instance the low-tohigh transition. Three possible input scenarios can be identified for charging the output to
VDD. If both inputs are driven low, the two PMOS devices are on. The delay in this case is
0.69 × (Rp/2) × CL, since the two resistors are in parallel. This is not the worst-case low-tohigh transition, which occurs when only one device turns on, and is given by 0.69 × Rp ×
CL. For the pull-down path, the output is discharged only if both A and B are switched
high, and the delay is given by 0.69 × (2RN) × CL to a first order. In other words, adding
devices in series slows down the circuit, and devices must be made wider to avoid a performance penalty. When sizing the transistors in a gate with multiple fan-in’s, we should
pick the combination of inputs that triggers the worst-case conditions.
For example, for a NAND gate to have the same pull-down delay (tphl) as a minimum-sized inverter, the NMOS devices in the NAND stack must be made twice as wide
so that the equivalent resistance the NAND pull-down is the same as the inverter. The
PMOS devices can remain unchanged.
This first-order analysis assumes that the extra capacitance introduced by widening
the transistors can be ignored. This is not a good assumption in general, but allows for a
reasonable first cut at device sizing.
Example 6.3 Delay dependence on input patterns
Consider the NAND gate of Figure 6.8a. Assume NMOS and PMOS devices of
0.5µm/0.25µm and 0.75µm/0.25µm, respectively. This sizing should result in approximately
equal worst-case rise and fall times (since the effective resistance of the pull-down is
designed to be equal to the pull-up resistance).
Section 6.2
Static CMOS Design
237
Figure 6.9 shows the simulated low-to-high delay for different input patterns. As
expected, the case where both inputs transition go low (A = B = 1→0) results in a smaller
delay, compared to the case where only one input is driven low. Notice that the worst-case
low-to-high delay depends upon which input (A or B) goes low. The reason for this involves
the internal node capacitance of the pull-down stack (i.e., the source of M2). For the case that
B = 1 and A transitions from 1→0, the pull-up PMOS device only has to charge up the output
node capacitance since M2 is turned off. On the other hand, for the case where A=1 and B transitions from 1→0, the pull-up PMOS device has to charge up the sum of the output and the
internal node capacitances, which slows down the transition.
3.0
A = B = 1→0
Voltage, V
2.0
A = 1, B = 1→0
1.0
A = 1→0, B =1
0.0
-1.00
100
200
300
time, psec
400
Input Data
Pattern
Delay
(psec)
A = B= 0→1
69
A = 1, B= 0→1
62
A= 0→1, B = 1
50
A=B=1→0
35
A=1, B = 1→0
76
A= 1→0, B = 1
57
Figure 6.9 Example showing the delay dependence on input patterns.
The table in Figure 6.9 shows a compilation of various delays for this circuit. The firstorder transistor sizing indeed provides approximately equal rise and fall delays. An important
point to note is that the high-to-low propagation delay depends on the state of the internal
nodes. For example, when both inputs transition from 0→1, it is important to establish the
state of the internal node. The worst-case happens when the internal node is charged up to
VDD-VTn. The worst case can be ensured by pulsing the A input from 1 →0→1, while input B
only makes the 0→1. In this way, the internal node is initialized properly.
The important point to take away from this example is that estimation of delay can be
fairly complex, and requires a careful consideration of internal node capacitances and data
patterns. Care must be taken to model the worst-case scenario in the simulations. A brute
force approach that applies all possible input patterns, may not always work as it is important
to consider the state of internal nodes.
The CMOS implementation of a NOR gate (F = A + B) is shown in Figure 6.10. The
output of this network is high, if and only if both inputs A and B are low. The worst-case
pull-down transition happens when only one of the NMOS devices turns on (i.e., if either
A or B is high). Assume that the goal is to size the NOR gate such that it has approximately the same delay as an inverter with the following device sizes: NMOS
0.5µm/0.25µm and PMOS 1.5µm/0.25µm. Since the pull-down path in the worst case is a
single device, the NMOS devices (M1 and M2) can have the same device widths as the
NMOS device in the inverter. For the output to be pulled high, both devices must be
turned on. Since the resistances add, the devices must be made two times larger compared
to the PMOS in the inverter (i.e., M3 and M4 must have a size of 3µm/0.25µm). Since
PMOS devices have a lower mobility relative to NMOS devices, stacking devices in series
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
238
Chapter 6
must be avoided as much as possible. A NAND implementation is clearly preferred over a
NOR implementation for implementing generic logic.
VDD
VDD
RP
M4
B
B
M1
F
M2
B
RN
A
Problem 6.1
Cint
A
F
A
Figure 6.10 Sizing of a NOR gate to
produce the same delay as an inverter with
size of NMOS: 0.5µm/0.25µm and PMOS:
1.5µm/0.25µm.
F
RP
M3
A
RN
CL
B
Transistor Sizing in Complementary CMOS Gates
Determine the transistor sizes of the individual transistors in Figure 6.6c such that it has
approximately the same tplh and tphl as a inverter with the following sizes: NMOS:
0.5µm/0.25µm and PMOS: 1.5µm/0.25µm.
So far in the analysis of propagation delay, we have ignored the effect of internal
node capacitances. This is often a reasonable assumption for a first-order analysis. However, in more complex logic gates that have large fan-in, the internal node capacitances
can become significant. Consider a 4-input NAND gate as shown in Figure 6.11, which
shows the equivalent RC model of the gate, including the internal node capacitances. The
internal capacitances consist of the junction capacitance of the transistors, as well as the
gate-to-source and gate-to-drain capacitances. The latter are turned into capacitances to
ground using the Miller equivalence. The delay analysis for such a circuit involves solving
distributed RC networks, a problem we already encountered when analyzing the delay of
interconnect networks. Consider the pull-down delay of the circuit. The output is discharged when all inputs are driven high. The proper initial conditions must be placed on
the internal nodes (this is, the internal nodes must be charged to VDD-VTN) before the
inputs are driven high.
VDD
VDD
A
M5 B
M7 D
M6 C
A
B
M4
M3
M8
A
R5
B
R6
R7
C
D
M2
A
R3
R2
C
D
M1
F
CL
R4
B
C
R8
R1
D
C3
C2
C1
Figure 6.11 Four input NAND
gate and its RC model.
Section 6.2
Static CMOS Design
239
The propagation delay can be computed using the Elmore delay model and is
approximated as:
t pHL = 0.69 ( R 1 ⋅ C 1 + ( R 1 + R 2 ) ⋅ C 2 + ( R 1 + R 2 + R 3 ) ⋅ C 3 + ( R 1 + R 2 + R 3 + R 4 ) ⋅ C L )
(6.3)
Notice that the resistance of M1 appears in all the terms, which makes this device
especially important when attempting to minimize delay. Assuming that all NMOS
devices have an equal size, Eq. (6.3) simplifies to
t
pHL
(6.4)
= 0.69R N ( C + 2 ⋅ C + 3 ⋅ C + 4 ⋅ C L )
1
2
3
Example 6.4 A Four-Input Complementary CMOS NAND Gate
In this example, the intrinsic propagation delay of the 4 input NAND gate (without any loading) is evaluated using hand analysis and simulation. Assume that all NMOS devices have a
W/L of 0.5µm/0.25µm, and all PMOS devices have a device size of 0.375µm/0.25µm. The
layout of a four-input NAND gate is shown in Figure 6.12. The devices are sized such that the
worst case rise and fall time are approximately equal (to first order ignoring the internal node
capacitances).
Using techniques similar to those employed for the CMOS inverter in Chapter 3, the
capacitances values can be computed from the layout. Notice that in the pull-up path, the
PMOS devices share the drain terminal in order to reduce the overall parasitic contribution to
the output. Using our standard design rules, the area and perimeter for various devices can be
easily computed as shown in Table 6.1
In this example, we will focus on the pull-down delay, and the capacitances will be
computed for the high-to-low transition at the output. While the output makes a transition
from VDD to 0, the internal nodes only transition from VDD-VTn to GND. We would need to
linearize the internal junction capacitances for this voltage transition, but, to simplify the
analysis, we will use the same Keff for the internal nodes as for the output node.
VDD
Out
GND
A
B
C
D
Figure 6.12 Layout a four-input NAND gate in complementary CMOS.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
240
Chapter 6
Table 6.1 Area and perimeter of transistors in 4 input NAND gate.
Transistor
W (µm)
AS (µm2)
AD (µm2)
PS (µm)
PD(µm)
1
0.5
0.3125
0.0625
1.75
0.25
2
0.5
0.0625
0.0625
0.25
0.25
3
0.5
0.0625
0.0625
0.25
0.25
4
0.5
0.0625
0.3125
0.25
1.75
5
0.375
0.296875
0.171875
1.875
0.875
6
0.375
0.171875
0.171875
0.875
0.875
7
0.375
0.171875
0.171875
0.875
0.875
8
0.375
0.296875
0.171875
1.875
0.875
It is assumed that the output connects to a single, minimum-size inverter. The effect of
intra-cell routing, which is small, is ignored. The various contributions are summarized in
Table 6.2. For the NMOS and PMOS junctions, we use Keq = 0.57, Keqsw = 0.61, and Keq
= 0.79, Keqsw = 0.86, respectively. Notice that the gate-to-drain capacitance is multiplied
by a factor of two for all internal nodes and the output node to account for the Miller
effect (this ignores the fact that the internal nodes have a slightly smaller swing due to
the threshold drop).
Table 6.2 Computation of capacitances for high-to-low transition at the output. The table shows
the intrinsic delay of the gate without extra loading. Any fan-out capacitance would simply be
added to the CL term.
Capacitor
Contributions (H→L)
Value (fF) (H→L)
C1
Cd1 + Cs2 + 2 * Cgd1 + 2 * Cgs2
(0.57 * 0.0625 * 2+ 0.61 * 0.25 * 0.28) +
(0.57 * 0.0625 * 2+ 0.61 * 0.25* 0.28) +
2 * (0.31 * 0.5) + 2 * (0.31 * 0.5) = 0.85fF
C2
Cd2 + Cs3 + 2 * Cgd2 + 2 * Cgs3
(0.57 * 0.0625 * 2+ 0.61 * 0.25 * 0.28) +
(0.57 * 0.0625 * 2+ 0.61 * 0.25* 0.28) +
2 * (0.31 * 0.5) + 2 * (0.31 * 0.5) = 0.85fF
C3
Cd3 + Cs4 + 2 * Cgd3 + 2 * Cgs4
(0.57 * 0.0625 * 2+ 0.61 * 0.25 * 0.28) +
(0.57 * 0.0625 * 2+ 0.61 * 0.25* 0.28) +
2 * (0.31 * 0.5) + 2 * (0.31 * 0.5) = 0.85fF
CL
(0.57 * 0.3125 * 2 + 0.61 * 1.75 *0.28) +
Cd4 + 2 * Cgd4 + Cd5 +Cd6 +Cd7 + Cd8 +
2 * Cgd5+2 * Cgd6+ 2 * Cgd7+ 2 * Cgd8 2 * (0.31 * 0.5)+ 4 * (0.79 * 0.171875* 1.9+ 0.86
* 0.875 * 0.22)+ 4 * 2 * (0.27 * 0.375) = 3.47fF
= Cd4 + 4 * Cd5 + 4 * 2 * Cgd6
Using Eq. (6.4), we can compute the propagation delay as:
13KΩ
tpHL = 0.69 --------------- ( 0.85fF + 2 ⋅ 0.85fF + 3 ⋅ 0.85fF + 4 ⋅ 3.47 fF ) = 85 p s
2
The simulated delay for this particular transition was found to be 86 psec! The hand analysis
gives a fairly accurate estimate given all assumptions and linearizations made. For example,
we assume that the gate-source (or gate-drain) capacitance only consists of the overlap component. This is not entirely the case, as during the transition some other contributions come in
place depending upon the operating region. Once again, the goal of hand analysis is not to
Section 6.2
Static CMOS Design
241
provide a totally accurate delay prediction, but rather to give intuition into what factors influence the delay and to aide in initial transistor sizing. Accurate timing analysis and transistor
optimization is usually done using SPICE. The simulated worst-case low-to-high delay time
for this gate was 106ps.
While complementary CMOS is a very robust and simple approach for implementing logic gates, there are two major problems associated with using this style as the complexity of the gate (i.e., fan-in) increases. First, the number of transistors required to
implement an N fan-in gate is 2N. This can result in significant implementation area. The
second problem is that propagation delay of a complementary CMOS gate deteriorates
rapidly as a function of the fan-in. The large number of transistors (2N) increases the overall capacitance of the gate. For an N-input NAND gate, the output capacitance increases
linearly with the fan-in since the number of PMOS devices connected to the output node
increases linearly with the fan-in. Also, a series connection of transistors in either the PUN
or PDN slows the gate as well, because the effective (dis)charging resistance is increased.
For the same N-input NAND gate, the effective resistance of the PDN path increases linearly with the fan-in. Since the output capacitance increase linearly and the pull-down
resistance increases linearly, the high-to-low delay can increase in a quadratic fashion.
The fan-out has a large impact on the delay of complementary CMOS logic as well.
Each input to a CMOS gate connects to both an NMOS and a PMOS device, and presents
a load to the driving gate equal to the sum of the gate capacitances.
The above observations are summarized by the following formula, which approximates the influence of fan-in and fan-out on the propagation delay of the complementary
CMOS gate
t p = a 1 FI + a 2 FI 2 + a 3 FO
(6.5)
where FI and FO are the fan-in and fan-out of the gate, respectively, and a1, a2 and a3 are
weighting factors that are a function of the technology.
At first glance, it would appear that the increase in resistance for larger fan-in can be
solved by making the devices in the transistor chain wider. Unfortunately, this does not
improve the performance as much as expected, since widening a device also increases its
gate and diffusion capacitances, and has an adverse affect on the gate performance. For
the N-input NAND gate, the low-to-high delay only increases linearly since the pull-up
resistance remains unchanged and only the capacitance increases linearly.
Figure 6.13 show the propagation delay for both transitions as a function of fan-in
assuming a fixed fan-out (NMOS: 0.5µm and PMOS: 1.5µm). As predicted above, the
tpLH increases linearly due to the linearly-increasing value of the output capacitance. The
simultaneous increase in the pull-down resistance and the load capacitance results in an
approximately quadratic relationship for tpHL. Gates with a fan-in greater than or equal to 4
become excessively slow and must be avoided.
Design Techniques for Large Fan-in
Several approaches may be used to reduce delays in large fan-in circuits.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
242
Chapter 6
1250
tpHL
tp (psec)
1000
750
500
tpLH
250
02
4
6
8
10
Fan-in
12
14
16
Figure 6.13 Propagation delay of
CMOS NAND gate as a function of
fan-in. A fan-out of one inverter is
assumed, and all pull-down
transistors are minimal size.
1. Transistor Sizing
The most obvious solution is to increase the overall transistor size. This lowers the resistance of devices in series and lowers the time constant. However, increasing the transistor size,
results in larger parasitic capacitors, which do not only affect the propagation delay of the gate
in question, but also present a larger load to the preceding gate. This technique should, therefore, be used with caution. If the load capacitance is dominated by the intrinsic capacitance of
the gate, widening the device only creates a “self-loading” effect, and the propagation delay is
unaffected. A more comprehensive approach towards sizing transistors in complex CMOS
gates is discussed in the next section.
2. Progressive Transistor Sizing
An alternate approach to uniform sizing (in which each transistor is scaled up uniformly), is to use progressive transistor sizing (Figure 6.14). Referring back to Eq. (6.3), we see
that the resistance of M1 (R1) appears N times in the delay equation, the resistance of M2 (R2)
appears N-1 times, etc. From the equation, it is clear that R1 should be made the smallest, R2 the
next smallest, etc. Consequently, a progressive scaling of the transistors is beneficial: M1 > M2
> M3 > MN. Basically, in this approach, the important resistance is reduced while reducing
capacitance. For an excellent treatment on the optimal sizing of transistors in a complex network, we refer the interested reader to [Shoji88, pp. 131–143]. The reader should be aware of
Out
InN
MN
In3
M3
In2
M2
C2
In1
M1
C1
CL
C3
M1 > M 2 > M3 > M N
Figure 6.14 Progressive sizing of transistors in large transistor
chains copes with the extra load of internal capacitances.
Section 6.2
Static CMOS Design
243
CL
In3
M3
In2
M2
C2
In1
M1
C1
CL
In1
M1
In2
M2
C2
In3
M3
C3
(a)
(b)
Figure 6.15 Influence of transistor ordering on delay. Signal In1 is the critical signal.
one important pitfall of this approach. While progressive resizing of transistors is relatively
easy in a schematic diagram, it is not as simple in a real layout. Very often, design-rule considerations force the designer to push the transistors apart, which causes the internal capacitance
to grow. This may offset all the gains of the resizing!
3. Input Re-Ordering
Some signals in complex combinational logic blocks might be more critical than others.
Not all inputs of a gate arrive at the same time (due, for instance, to the propagation delays of
the preceding logical gates). An input signal to a gate is called critical if it is the last signal of
all inputs to assume a stable value. The path through the logic which determines the ultimate
speed of the structure is called the critical path.
Putting the critical-path transistors closer to the output of the gate can result in a speedup. This is demonstrated in Figure 6.15. Signal In1 is assumed to be a critical signal. Suppose
further that In2 and In3 are high and that In1 undergoes a 0→1 transition. Assume also that CL
is initially charged high. In case (a), no path to GND exists until M1 is turned on, which is
unfortunately the last event to happen. The delay between the arrival of In1 and the output
is therefore determined by the time it takes to discharge CL, C1 and C2. In the second case,
C1 and C2 are already discharged when In 1 changes. Only CL still has to be discharged,
resulting in a smaller delay.
4. Logic Restructuring
Manipulating the logic equations can reduce the fan-in requirements and hence reduce
the gate delay, as illustrated in Figure 6.16. The quadratic dependency of the gate delay on fanin makes the six-input NOR gate extremely slow. Partitioning the NOR-gate into two threeinput gates results in a significant speed-up, which offsets by far the extra delay incurred by
turning the inverter into a two-input NAND gate.
Figure 6.16 Logic restructuring
can reduce the gate fan-in.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
244
Chapter 6
Transistor Sizing for Performance in Combinational Networks
Earlier, we established that minimization of the propagation delay of a gate in isolation is
a purely academic effort. The sizing of devices should happen in its proper context. In
Chapter 5, we developed a methodology to do so for inverters. In Chapter 5 we found out
that an optimal fanout for a chain of inverters driving a load CL is (CL/Cin)1/N, where N is
the number of stages in the chain, and Cin the input capacitance of the first gate in the
chain. If we have an opportunity to select the number of stages, we found out that we
would like to keep the fanout per stage around 4. Can this result be extended to determine
the size of any combinational path for minimal delay? By extending our previous
approach to address complex logic networks, we will find out that this is indeed possible
[Sutherland99].1
To do so, we modify the basic delay equation of the inverter, introduced in Chapter
5, and repeated here for the sake of clarity,
C ext
t p = t p0 1 + --------= t p0 ( 1 + f ⁄ γ )
γC g
(6.6)
t p = t p0 ( p + gf ⁄ γ )
(6.7)
to
with tp0 still representing the intrinsic delay of an inverter, and f the ratio between the
external load and the input capacitance of the gate. In this context, f is often called the
electrical effort. p represents the ratio of the intrinsic (or unloaded) delays of the complex
gate and the simple inverter. The more involved structure of the multiple-input gate, combined with its series devices, increases its intrinsic delay. p is a function of gate topology
as well as layout style. Table 6.3 enumerates the values of p for some standard gates,
assuming simple layout styles, and ignoring second-order effects such as internal node
capacitances.
Table 6.3 Estimates of intrinsic delay factors of various logic types assuming simple layout styles, and
a fixed PMOS/NMOS ratio.
Gate type
p
Inverter
1
n-input NAND
n
n-input NOR
n
n-way multiplexer
2n
XOR, NXOR
n2n-1
1
The approach introduced in this section is commonly called logical effort, and was first introduced in
[Sutherland99], which presents an extensive treatment of the topic. The treatment offered here represents only a
glance-over of the overall approach.
Section 6.2
Static CMOS Design
245
The factor g is called the logical effort, and represents the fact that, for a given load,
complex gates have to work harder than an inverter to produce a similar response. In other
words, the logical effort of a logic gate tells how much worse it is at producing output current than an inverter, given that each of its inputs may contain only the same input capacitance as the inverter. Equivalently, logical effort is how much more input capacitance a
gate presents to deliver the same output current as an inverter. Logical effort is a useful
parameter, because it depends only on circuit topology. The logical efforts of some common logic gates are given in Table 6.4.
Table 6.4 Logic efforts of common logic gates, assuming a PMOS/NMOS ratio of 2.
Number of Inputs
Gate Type
1
2
3
n
Inverter
1
NAND
4/3
5/3
(n+2)/3
NOR
5/3
7/3
(2n+1)/3
Multiplexer
2
2
2
XOR
4
12
Example 6.5 Logical effort of complex gates
Consider the gates shown in Figure 6.17. Assuming an PMOS/NMOS ratio of 2, the input
capacitance of a minimum-sized symmetrical inverter equals 3 times the gate capacitance of a
minimum-sized NMOS (called Cunit). We size the 2-input NAND and NOR such that their
equivalent resistances equal the resistance of the inverter (using the techniques described earlier). This increases the input capacitance of the 2-input NOR to 4 Cunit, or 4/3 the capacitance
of the inverter.The input capacitance of the 2-input NOR is 5/3 that of the inverter. Equivalently, for the same input capacitance, the NAND and NOR gate have 4/3 and 5/3 less driving
strength than the inverter. This affects the delay component that corresponds to the load,
increasing it by this same factor, called ‘logical effort.’ Hence, gNAND = 4/3, and gNOR = 5/3.
VDD
A
A
2
2
B
2
F
F
A
A
VDD
VDD
Inverter
4
A
4
2
1
F
A
B
B
1
B
1
2
2-input NAND
Figure 6.17 Logical effort of 2-input NAND
and NOR gates.
2-input NOR
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
246
Chapter 6
AN
N
2in
pu
t
Normalized Delay
D
:g
=4
/3
;
p=
2
The delay model of a logic gate, as
represented in Eq. (6.7), is a simple
linear relationship. Figure 6.18 shows
5
this relationship graphically: the delay
=1
is plotted as a function of the fanout
p
4
1;
g=
(electrical effort) for an inverter and
:
ter
er
for a 2-input NAND gate. The slope of
3
v
Effort
In
Delay
the line is the logical effort of the gate;
2
its intercept is the intrinsic delay. The
graph shows that we can adjust the
1
Intrinsic
delay by adjusting the effective fanout
Delay
(by transistor sizing) or by choosing a
logic gate with a different logical
1
2
3
4
5
Fanout f
effort. Observe also that fanout and
Figure 6.18 Delay as a function of fanout for an
logical effort contribute to the delay in
inverter and a 2-input NAND.
a similar way. We call the product of
the two h = fg the gate effort.
The total delay of a path through a combinational logic block can now be expressed
as
N
tp =
∑t
N
p, j
= t p0
∑ p + -------γ
fj gj
j
(6.8)
j=1
j=1
We use a similar procedure as we did for the inverter chain in Chapter 5 to determine the
minimum delay of the path. By finding N – 1 partial derivatives and setting theme to zero,
we find that each stage should bear the same ‘effort’:
f1 g 1 = f2 g2 = … = f N g N
(6.9)
The fanouts along the path can be multiplied to get a path effective fanout, and so can the
logical efforts.
F = f 1 f 2 …f N = C L ⁄ C g1
G = g 1 g 2 …g N
(6.10)
The path effort can then be defined as the product of the two, or H = FG. From here on, the
analysis proceeds along the same lines as the inverter chain. The gate effort that minimizes
the path delay is found to equal
h =
N
FG =
N
H,
(6.11)
and the minimum delay through the path is
D = t p0
N
N ( N H )
∑ p + -----------------γ
j
j=1
(6.12)
Section 6.2
Static CMOS Design
247
Note that the overall intrinsic delay is a function of the types of logic gates in the path, and
is not affected by the sizing.
Example 6.6 Sizing combinational logic for minimum delay
Consider the logic network of Figure 6.19, which may represent the critical path of a more
complex logic block. The output of the network is loaded with a capacitance which is 5 times
larger than the input capacitance of the first gate, which is a minimum-sized inverter. The
effective fanout of the path hence equals F = CL/Cg1 = 5. Using the entries in Table 6.4, we
find the path logical effort
5 5
25
G = 1 × --- × --- × 1 = -----3 3
9
H = FG = 125/9, and the optimal stage effort h is 4 H = 1.93. Taking into account the gate
types, we derive the fanout factors: f1 = 1.93; f2 = 1.93×(3/5) = 1.16; f3 = 1.16; f4=1.93. Notice
that the inverters are assigned larger electrical efforts than the more complex gates because
they are better at driving loads. From this, we can derive the sizes of the gates (with respect to
their minimum-sized versions): a = f1/g2 = 1.16; b = f1f2/g3= 1.34; c = f1f2f3/g4=2.60.
These calculations do not have to be very precise. As discussed in the Chapter 5, sizing
a gate too large or too small by a factor of 1.5 still result in circuits within 5% of minimum
delay. Therefore, the “back of the envelope” hand calculations using this technique are quite
effective.
1
a
b
c
5
Figure 6.19 Critical path of
combinational network.
Power Consumption in CMOS Logic Gates
The sources of power consumption in a complementary CMOS inverter were discussed in
detail in Chapter 5. Many of these issues apply directly to complex CMOS gates. The
power dissipation is a strong function of transistor sizing (which affects physical capacitance), input and output rise/fall times (which affects the short-circuit power), device
thresholds and temperature (which affect leakage power), and switching activity. The
dynamic power dissipation is given by α0→1 CL VDD2 f. Making a gate more complex
mostly affects the switching activity α0→1, which has two components: a static component
that is only a function of the topology of the logic network, and a dynamic one that results
from the timing behavior of the circuit—the latter factor is also called glitching.
Logic Function—The transition activity is a strong function of the logic function being
implemented. For static CMOS gates with statistically independent inputs, the static
transition probability is the probability p0 that the output will be in the zero state in one
cycle, multiplied by the probability p1 that the output will be in the one state in the next
cycle:
α0 → 1 = p0 • p 1 = p0 • ( 1 – p 0 )
(6.13)
248
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
Chapter 6
Assuming that the inputs are independent and uniformly distributed, any N-input static
gate has a transition probability that corresponds to
N
N0 • 2 – N 0
N0 N1
α 0 → 1 = ------- • ------- = -------------------------------------N
N
2N
2
2
2
(6.14)
where N0 is the number of zero entries and N1 is the number of one entries in the output
column of the truth table of the function. To illustrate, consider a static 2-input NOR gate
whose truth table is shown in Table 6.5. Assume that only one input transition is possible
during a clock cycle, and that the inputs to the NOR gate have a uniform input distribution
—this is, the four possible states for inputs A and B (00, 01, 10, 11) are equally likely.
Table 6.5 Truth table of a 2 input NOR gate.
A
B
Out
0
0
1
0
1
0
1
0
0
1
1
0
From Table 6.5 and Eq. (6.14), the output transition probability of a 2-input static
CMOS NOR gate can be derived:
N
2
N • 2 – N
3 • 2 – 3
0
0
3
α 0 → 1 = -------------------------------------- = ----------------------------- = -----16
2•2
2N
2
2
(6.15)
Problem 6.2 N input XOR gate
Assuming the inputs to an N-input XOR gate are uncorrelated and uniformly distributed,
derive the expression for the switching activity factor.
Signal Statistics—The switching activity of a logic gate is a strong function of the input
signal statistics. Using a uniform input distribution to compute activity is not a good one
since the propagation through logic gates can significantly modify the signal statistics. For
example, consider once again a 2-input static NOR gate, and let pa and pb be the
probabilities that the inputs A and B are one. Assume further that the inputs are not
correlated. The probability that the output node equals one is given by
p1 = (1-pa) (1-pb)
(6.16)
Therefore, the probability of a transition from 0 to 1 is
α0->1 = p0 p1 = (1-(1-pa) (1-pb)) (1-pa) (1-pb)
(6.17)
Section 6.2
Static CMOS Design
249
Figure 6.20 Transition activity of
a two-input NOR gate as a
function of the input probabilities
(pA,pB)
Figure 6.20 shows the transition probability as a function of pa and pb. Observe how
this graph degrades into the simple inverter case when one of the input probabilities is set
to 0. From this plot, it is clear that understanding the signal statistics and their impact on
switching events can be used to significantly impact the power dissipation.
Problem 6.3
Power Dissipation of Basic Logic Gates
Derive the 0 → 1 output transition probabilities for the basic logic gates (AND, OR, XOR).
The results to be obtained are given in Table 6.6.
Table 6.6
Output transition probabilities for static logic gates.
α0→1
AND
(1 – pApB)pApB
OR
(1 – pA)(1 – pB)[1 – (1 – pA)(1 – pB)]
XOR
[1 – (pA + pB – 2pApB)](pA + pB – 2pApB)
Inter-signal Correlations—The evaluation of the switching activity is further
complicated by the fact that signals exhibit correlation in space and time. Even if the
primary inputs to a logic network are uncorrelated, the signals become correlated or
“colored”, as they propagate through the logic network. This is best illustrated with a
simple example. Consider first the circuit shown in Figure 6.21a, and assume that the
primary inputs, A and B, are uncorrelated and uniformly distributed. Node C has a 1 (0)
probability of 1/2, and a 0->1 transition probability of 1/4. The probability that the node Z
undergoes a power consuming transition is then determined using the AND-gate expression of Table 6.6.
p0->1 = (1- pa pb) pa pb = (1-1/2 • 1/2) 1/2 • 1/2 = 3/16
(6.18)
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
250
A
C
Chapter 6
C
A
Z
Z
B
B
(a) Logic circuit without
(b) Logic circuit with
reconvergent fanout
reconvergent fanout
Figure 6.21 Example illustrating the effect of signal correlations.
The computation of the probabilities is straightforward: signal and transition probabilities are evaluated in an ordered fashion, progressing from the input to the output node.
This approach, however, has two major limitations: (1) it does not deal with circuits with
feedback as found in sequential circuits; (2) it assumes that the signal probabilities at the
input of each gate are independent. This is rarely the case in actual circuits, where reconvergent fanout often causes inter-signal dependencies. For instance, the inputs to the AND
gate in Figure 6.21b (C and B) are inter-dependent as both are a function of A. The
approach to compute probabilities, presented previously, fails under these circumstances.
Traversing from inputs to outputs yields a transition probability of 3/16 for node Z, similar
to the previous analysis. This value for transition probability is clearly false, as logic transformations show that the network can be reduced to Z = C•B = A•A = 0, and no transition
will ever take place.
To get the precise results in the progressive analysis approach, its is essential to take
signal inter-dependencies into account. This can be accomplished with the aid of conditional probabilities. For an AND gate, Z equals 1 if and only if B and C are equal to 1.
pZ = p(Z=1) = p(B=1, C=1)
(6.19)
where p(B=1,C=1) represents the probability that B and C are equal to 1 simultaneously. If
B and C are independent, p(B=1,C=1) can be decomposed into p(B=1) • p(C=1), and this
yields the expression for the AND-gate, derived earlier: pZ = p(B=1) • p(C=1) = pB pC. If a
dependency between the two exists (as is the case in Figure 6.21b), a conditional probability has to be employed, such as
pZ = p(C=1|B=1) • p(B=1)
(6.20)
The first factor in Eq. (6.20) represents the probability that C=1 given that B=1. The
extra condition is necessary as C is dependent upon B. Inspection of the network shows
that this probability is equal to 0, since C and B are logical inversions of each other, resulting in the signal probability for Z, pZ = 0.
Deriving those expressions in a structured way for large networks with reconvergent
fanout is complex, especially when the networks contain feedback loops. Computer support is therefore essential. To be meaningful, the analysis program has to process a typical
sequence of input signals, as the power dissipation is a strong function of statistics of those
signals.
Dynamic or Glitching Transitions—When analyzing the transition probabilities of
complex, multistage logic networks in the preceding section, we ignored the fact that the
gates have a non-zero propagation delay. In reality, the finite propagation delay from one
Section 6.2
Static CMOS Design
251
Out1
Out2
Out3
Out4
Out5
1
...
3.0
Out6
Voltage, V
Out2
2.0
Out6
Out8
Out7
1.0
Out1
Out5
Out3
0.0
0
200
400
Figure 6.22 Glitching in a chain of NAND
gates.
600
time, psec
logic block to the next can cause spurious transitions, called glitches, critical races, or
dynamic hazards, to occur: a node can exhibit multiple transitions in a single clock cycle
before settling to the correct logic level.
A typical example of the effect of glitching is shown in Figure 6.22, which displays
the simulated response of a chain of NAND gates for all inputs going simultaneously from
0 to 1. Initially, all the outputs are 1 since one of the inputs was 0. For this particular transition, all the odd bits must transition to 0 while the even bits remain at the value of 1.
However, due to the finite propagation delay, the higher order even outputs start to discharge and the voltage drops. When the correct input ripples through the network, the output goes high. The glitch on the even bits causes extra power dissipation beyond what is
required to strictly implement the logic function. Although the glitches in this example are
only partial (i.e., not from rail to rail), they contribute significantly to the power dissipation. Long chains of gates often occur in important structures such as adders and multipliers and the glitching component can easily dominate the overall power consumption.
Design Techniques to Reduce Switching Activity
The dynamic power of a logic gate can be reduced by minimizing the physical capacitance and
the switching activity. The physical capacitance can be minimized in a number ways, including
circuit style selection, transistor sizing, placement and routing, and architectural optimizations.
The switching activity, on the other hand, can be minimized at all level of the design abstraction, and is the focus of this section. Logic structures can be optimized to minimize both the
fundamental transitions required to implement a given function, and the spurious transitions.
1. Logic Restructuring
Changing the topology of a logic network may reduce its power dissipation. Consider for
instance two alternate implementations of F = A • B • C • D, as shown in Figure 6.23. Ignore
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
252
O1
A
B
C
O2
A
B
F
D
C
D
Chain structure
Chapter 6
O1
F
O2
Tree structure
Figure 6.23 Simple example to demonstrate the influence of circuit topology on activity.
glitching and assume that all primary inputs (A,B,C,D) are uncorrelated and uniformly distributed (i.e., p1 (a,b,c,d)= 0.5). Using the expressions from Table 6.6, the activity can be computed
for the two topologies, as shown in Table 6.7. The results indicate that the chain implementation will have an overall lower switching activity than the tree implementation for random
inputs. However, as mentioned before, it is also important to consider the timing behavior to
accurately make power trade-offs. In this example the tree topology will have lower (no)
glitching activity since the signal paths are balanced to all the gates.
Table 6.7Probabilities for tree and chain topologies.
O1
O2
F
p1 (chain)
1/4
1/8
1/16
p0 = 1-p1 (chain)
3/4
7/8
15/16
p0->1 (chain)
3/16
7/64
15/256
p1 (tree)
1/4
1/4
1/16
p0 = 1-p1 (tree)
3/4
3/4
15/16
p0->1 (tree)
3/16
3/16
15/256
2. Input ordering
Consider the two static logic circuits of Figure 6.24. The probabilities of A, B and C being 1 are
listed in the Figure. Since both circuits implement identical logic functionality, it is clear that
the activity at the output node Z is equal in both cases. The difference is in the activity at the
intermediate node. In the first circuit, this activity equals (1 − 0.5 × 0.2) (0.5 × 0.2) = 0.09. In
the second case, the probability that a 0 → 1 transition occurs equals (1 – 0.2 × 0.1) (0.2 × 0.1)
= 0.0196. This is substantially lower. From this we learn that it is beneficial to postpone the
introduction of signals with a high transition rate (i.e., signals with a signal probability close to
0.5). A simple reordering of the input signals is often sufficient to accomplish that goal.
3. Time-multiplexing resources
Time-multiplexing a single hardware resource—such as a logic unit or a bus—over a number
functions is an often used technique to minimize the implementation area. Unfortunately, the
minimum area solution does not always result in the lowest switching activity. For example,
consider the transmission of two input bits (A and B) using either dedicated resources or a timemultiplexed approach, as shown in Figure 6.25. To first order—ignoring the multiplexer over-
Section 6.2
Static CMOS Design
253
A
B
B
p(A = 1) = 0.5
p(B = 1) = 0.2
p(C = 1) = 0.1
C
Z
Z
C
A
Figure 6.24 Reordering of inputs affects the circuit activity.
head—, it would seem that the degree of time-multiplexing should not affect the switched
capacitance, since the time-multiplexed solution has half the capacitance switched at twice the
frequency (for a fixed throughput).
If data being transmitted were random, it will make no difference which architecture is
used. However if the data signals have some distinct properties (called temporal correlation),
the power dissipation of the time-multiplexed solution can be significantly higher. Suppose, for
instance, that A is always (or mostly) 1 and B is (mostly) 0. In the parallel solution, the
switched capacitance is very low since there are very few transitions on the data bits. However,
in the time-multiplexed solution, the bus toggles between 0 and 1. Care must be taken in digital
systems to avoid time-multiplexing data streams with very distinct data characteristics.
A
C
A
0
t
B
1
B
C
(a) parallel data transmission
0
A
1
B
t
C
t
(b) serial data transmission
Figure 6.25 Parallel versus time-multiplexed data busses.
4. Glitch Reduction by balancing signal paths
The occurrence of glitching in a circuit is mainly due to a mismatch in the path lengths in the
network. If all input signals of a gate change simultaneously, no glitching occurs. On the other
hand, if input signals change at different times, a dynamic hazard might develop. Such a mismatch in signal timing is typically the result of different path lengths with respect to the primary inputs of the network. This is illustrated in Figure 6.26. Assume that the XOR gate has a
unit delay. The first network (a) suffers from glitching as a result of the wide disparity between
the arrival times of the input signals for a gate. For example, for gate F3, one input settles at
time 0, while the second one only arrives at time 2. Redesigning the network so that all arrival
times are identical can dramatically reduce the number of superfluous transitions (network b).
Summary
The CMOS logic style described in the previous section is highly robust and scalable with
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
254
0
F1
0
1
0
0
2
F2
F1
1
F3
F3
0
Chapter 6
0
0
0
(a) Network sensitive to glitching
1
F2
(b) Glitch-free network
Figure 6.26 Glitching is influenced by matching of signal path lengths. The annotated numbers
indicate the signal arrival times.
technology, but requires 2N transistors to implement a N-input logic gate. Also, the load
capacitance is significant, since each gate drives two devices (a PMOS and an NMOS) per
fan-out. This has opened the door for alternative logic families that either are simpler or
faster.
6.2.2
Ratioed Logic
Concept
Ratioed logic is an attempt to reduce the number of transistors required to implement a
given logic function, at the cost of reduced robustness and extra power dissipation. The
purpose of the PUN in complementary CMOS is to provide a conditional path between
VDD and the output when the PDN is turned off. In ratioed logic, the entire PUN is replaced
with a single unconditional load device that pulls up the output for a high output (Figure
6.27a). Instead of a combination of active pull-down and pull-up networks, such a gate
consists of an NMOS pull-down network that realizes the logic function, and a simple load
device. Figure 6.27b shows an example of ratioed logic, which uses a grounded PMOS
load and is referred to as a pseudo-NMOS gate.
VDD
VDD
PMOS
load
load
F
In1
In2
In3
F
In1
In2
In3
PDN
(a) generic
PDN
(b) pseudo-NMOS
Figure 6.27 Ratioed logic gate.
The clear advantage of pseudo-NMOS is the reduced number of transistors (N+1
versus 2N for complementary CMOS). The nominal high output voltage (VOH) for this
gate is VDD since the pull-down devices are turned off when the output is pulled high
(assuming that VOL is below VTn). On the other hand, the nominal low output voltage is
Section 6.2
Static CMOS Design
255
not 0 V since there is a fight between the devices in the PDN and the grounded PMOS
load device. This results in reduced noise margins and more importantly static power dissipation. The sizing of the load device relative to the pull-down devices can be used to
trade-off parameters such a noise margin, propagation delay and power dissipation. Since
the voltage swing on the output and the overall functionality of the gate depends upon the
ratio between the NMOS and PMOS sizes, the circuit is called ratioed. This is in contrast
to the ratioless logic styles, such as complementary CMOS, where the low and high levels
do not depend upon transistor sizes.
Computing the dc-transfer characteristic of the pseudo-NMOS proceeds along paths
similar to those used for its complementary CMOS counterpart. The value of VOL is
obtained by equating the currents through the driver and load devices for Vin = VDD. At
this operation point, it is reasonable to assume that the NMOS device resides in linear
mode (since the output should ideally be close to 0V), while the PMOS load is saturated.
2
2
V DSAT
V OL
= k ( –V – V ) ⋅ V
k n ( V DD – V Tn )V OL – --------p
DD
Tp
DSAT – --------------
2
2
(6.21)
Assuming that VOL is small relative to the gate drive (VDD-VT) and that VTn is equal
to VTp in magnitude, VOL can be approximated as:
k p ( – V DD – V Tp ) ⋅ V DSAT µ p ⋅ W p
V OL ≈ --------------------------------------------------------≈ ----------------- ⋅ V DSAT
k n ( V DD – V Tn )
µn ⋅ Wn
(6.22)
In order to make VOL as small as possible, the PMOS device should be sized much
smaller than the NMOS pull-down devices. Unfortunately, this has a negative impact on
the propagation delay for charging up the output node since the current provided by the
PMOS device is limited.
A major disadvantage of the pseudo-NMOS gate is the static power that is dissipated when the output is low through the direct current path that exists between VDD and
GND. The static power consumption in the low-output mode is easily derived
2
P low
V DSATp
= V DD I low ≈ V DD ⋅ k p ( – V DD – V Tp ) ⋅ V DSATp – ---------------
2
(6.23)
Example 6.7 Pseudo-NMOS Inverter
Consider a simple pseudo-NMOS inverter (where the PDN network in Figure 6.27 degenerates to a single transistor) with an NMOS size of 0.5µm/0.25µm. The effect of sizing the
PMOS device is studied in this example to demonstrate the impact on various parameters.
The W/L ratio of the grounded PMOS is varied over values from 4, 2, 1, 0.5 to 0.25. Devices
with a W/L < 1 are constructed by making the length longer than the width. The voltage transfer curve for the different sizes is plotted in Figure 6.28.
Table 6.8 summarizes the nominal output voltage (VOL), static power dissipation, and
the low-to-high propagation delay. The low-to-high delay is measured as the time to reach
1.25V from VOL (which is not 0V for this inverter). This is chosen since the load gate is a
CMOS inverter with a switching threshold of 1.25V. The trade-off between the static and
dynamic properties is apparent. A larger pull-up device improves performance, but increases
static power dissipation and lowers noise margins (i.e., increases VOL).
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
256
Chapter 6
3.0
2.5
W/Lp = 4
2.0
Vout, V
1.5
W/Lp = 2
1.0
W/Lp = 0.5
W/Lp = 1
0.5
W/Lp = .25
0.0
0.0
0.5
1.0
1.5
2.0
2.5
Figure 6.28 Voltage-transfer curves of
the pseudo-NMOS inverter as a
function of the PMOS size.
Vin, V
Table 6.8Performance of a pseudo-NMOS inverter.
Size
VOL
Static Power
Dissipation
tplh
4
0.693V
564µW
14ps
2
0.273V
298µW
56ps
1
.133V
160µW
123ps
0.5
0.064V
80µW
268ps
0.25
0.031V
41µW
569ps
Notice that the simple first-order model to predict VOL is quite effective. For a
PMOS W/L of 4, VOL is given by (30/115) (4) (0.63V) = 0.66V.
The static power dissipation of pseudo-NMOS limits its use. However, pseudoNMOS still finds use in large fan-in circuits. Figure 6.29 shows the schematics of pseudoNMOS NOR and NAND gates. When area is most important, the reduced transistor count
compared to complimentary CMOS is quite attractive.
VDD
VDD
F
A
B
C
D
In1
Out
CL
(a) NOR
Figure 6.29 Four-input pseudo-NMOS NOR
and NAND gates.
In2
In3
In4
(b) NAND
Section 6.2
Static CMOS Design
Problem 6.4
257
NAND Versus NOR in Pseudo-NMOS
Given the choice between NOR or NAND logic, which one would you prefer for implementation in pseudo-NMOS?
How to Build Even Better Loads
It is possible to create a ratioed logic style that completely eliminates static currents and
provides rail-to-rail swing. Such a gate combines two concepts: differential logic and positive feedback. A differential gate requires that each input is provided in complementary
format, and produces complementary outputs in turn. The feedback mechanism ensures
that the load device is turned off when not needed. A example of such a logic family,
called Differential Cascode Voltage Switch Logic (or DCVSL), is presented conceptually
in Figure 6.30a [Heller84].
The pull-down networks PDN1 and PDN2 use NMOS devices and are mutually
exclusive (this is, when PDN1 conducts, PDN2 is off, and when PDN1 is off, PDN2 conducts), such that the required logic function and its inverse are simultaneously implemented. Assume now that, for a given set of inputs, PDN1 conducts while PDN2 does not,
and that Out and Out are initially high and low, respectively. Turning on PDN1, causes
Out to be pulled down, although there is still a fight between M1 and PDN1. Out is in a
high impedance state, as M2 and PDN2 are both turned off. PDN1 must be strong enough
to bring Out below VDD-|VTp|, the point at which M2 turns on and starts charging Out to
VDD —eventually turning off M1. This in turn enables Out to discharge all the way to GND.
Figure 6.30b shows an example of an XOR/XNOR gate. Notice that it is possible to share
transistors among the two pull-down networks, which reduces the implementation overhead
VDD
VDD
M1
VDD
Out
M2
Out
Out
A
A
B
B
Out
B
PDN1
B
B
B
PDN2
A
(a) Basic principle
A
(b) XOR-XNOR gate
Figure 6.30 DCVSL logic gate.
The resulting circuit exhibits a rail-to-rail swing, and the static power dissipation is
eliminated: in steady state, none of the stacked pull-down networks and load devices are
simultaneously conducting. However, the circuit is still ratioed since the sizing of the
PMOS devices relative to the pull-down devices is critical to functionality, not just perfor-
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
258
Chapter 6
mance. In addition to the problem of increase complexity in design, this circuit style still
has a power-dissipation problem that is due to cross-over currents. During the transition,
there is a period of time when PMOS and PDN are turned on simultaneously, producing a
short circuit path.
Example 6.8 DCVSL Transient Response
An example transient response is shown for an AND/NAND gate in DCVSL. Notice
that as Out is pulled down to VDD-|VTp|, Out starts to charge up to VDD quickly. The
delay from the input to Out is 197 psec and to Out is 321 psec. A static CMOS AND
gate (NAND followed by an inverter) has a delay of 200ps.
2.5
Out = A B
M1
A
M3 B
M4
Voltage,V
A
Out = A B
AB
1.5
0.5
B
AB
A,B
A,B
M2
-0.5 0
0.2
0.4
0.6
Time, ns
0.8
1.0
Figure 6.31Transient response of a simple AND/NAND DCVSL gate. M1 and M2
1µm/0.25µm, M3 and M4 are 0.5µm/0.25µm and the cross-coupled PMOS devices are
1.5µm/0.25µm.
Design Consideration: Single-ended versus Differential
The DCVSL gate provides differential (or complementary) outputs. Both the output signal
(Vout1) and its inverted value (Vout2) are simultaneously available. This is a distinct advantage,
as it eliminates the need for an extra inverter to produce the complementary signal. It has been
observed that a differential implementation of a complex function may reduce the number of
gates required by a factor of two! The number of gates in the critical timing path is often
reduced as well. Finally, the approach prevents some of the time-differential problems introduced by additional inverters. For example, in logic design it often happens that both a signal
and its complement are needed simultaneously. When the complementary signal is generated
using an inverter, the inverted signal is delayed with respect to the original (Figure 6.32a). This
causes timing problems, especially in very high-speed designs. The differential output capability avoids this problem (Figure 6.32b).
With all these positive properties, why not always use differential logic? Well, the differential nature virtually doubles the number of wires that has to be routed, leading very often to
unwieldy designs (on top of the additional implementation overhead in the individual gates).
Additionally, the dynamic power dissipation is high.
Section 6.2
Static CMOS Design
259
Vout2
Vout1
Vin
Vout2
Vin
Vout1
Vout2
Vout1
Vout1
(a) Single-ended
6.2.3
Vout2
(b) Differential
Figure 6.32 Advantage of differential
(b) over single-ended (a) gate.
Pass-Transistor Logic
Pass-Transistor Basics
A popular and widely-used alternative to complementary CMOS is pass-transistor logic,
which attempts to reduce the number of transistors required to implement logic by allowing the primary inputs to drive gate terminals as well as source/drain terminals
[Radhakrishnan85]. This is in contrast to logic families that we have studied so far, which
only allow primary inputs to drive the gate terminals of MOSFETS.
Figure 6.33 shows an implementation of the AND
B
function constructed that way, using only NMOS transistors. In this gate, if the B input is high, the top transisA
tor is turned on and copies the input A to the output F.
B
F = AB
When B is low, the bottom pass transistor is turned on
0
and passes a 0. The switch driven by B seems to be
redundant at first glance. Its presence is essential to Figure 6.33 Pass-transistor
ensure that the gate is static, this is that a low-imped- implementation of an AND gate.
ance path exists to the supply rails under all circumstances, or, in this particular case, when B is low.
The promise of this approach is that fewer transistors are required to implement a given
function. For example, the implementation of the AND gate in Figure 6.33 requires 4 transistors (including the inverter required to invert B), while a complementary CMOS implementation would require 6 transistors. The reduced number of devices has the additional
advantage of lower capacitance.
Unfortunately, as discussed earlier, an NMOS device is effective at passing a 0 but
is poor at pulling a node to VDD. When the pass transistor pulls a node high, the output
only charges up to VDD -VTn. In fact, the situation is worsened by the fact that the devices
experience body effect, as there exists a significant source-to-body voltage when pulling
high. Consider the case when the pass transistor is charging up a node with the gate and
drain terminals set at VDD. Let the source of the NMOS pass transistor be labeled x. Node
x will charge up to VDD-VTn(Vx):
V x = V DD – ( Vtn0 + γ ( (
2φf + V x ) –
2φ f ) )
(6.24)
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
260
Chapter 6
Example 6.9 Voltage swing for pass transistors circuits
Assuming a power supply voltage of 2.5V, the transient response of Figure 6.34 shows the
output of a NMOS charging up (where the drain voltage is at VDD and the gate voltage in is
ramped from 0V to VDD). Assume that node x was initially 0. Also notice that if IN is low,
3.0
In
1.5µm/0.25µm
x
VDD
0.5µm/0.25µm
Out
0.5µm/0.25µm
Voltage, V
IN
Out
2.0
x
1.0
0.0 0
0.5
1
Time, ns
1.5
2
Figure 6.34 Transient response of charging up a node using an N device. Notice the slow tail
after an initial quick response.
node x is in a high impedance state (not driven to one of the rails using a low resistance path).
Extra transistors can be added to provide a path to GND, but for this discussion, the simplified
circuit is sufficient. Notice that the output charges up quickly initially, but has slow tail. This
is attributed to the fact that the drive (gate to source voltage) reduces significantly as the output approaches VDD-VTn and the current available to charge up node x reduces drastically.
Hand calculation using Eq. (6.24), results in an output voltage of 1.8V, which comes close to
the simulated value.
WARNING:
The above example demonstrates that pass-transistor gates cannot be cascaded by connecting the output of a pass gate to the gate input of another pass transistor. This is
illustrated in Figure 6.35a, where the output of M1 (node x) drives the gate of another
MOS device. Node x can charge up to VDD-VTn1. If node C has a rail to rail swing, node Y
only charges up to the voltage on node x - VTn2, which works out to VDD-VTn1-VTn2. Figure
6.35b on the other hand has the output of M1 (x) driving the junction of M2, and there is
only one threshold drop. This is the proper way of cascading pass gates.
B
A
x
B
M1
A
C
Y
Out
C
Y
x
M1
M2
Out
M2
Swing on Y = VDD- VTn1
Swing on Y = VDD- VTn- VTn2
(b)
(a)
Figure 6.35 Pass transistor output (Drain/Source) terminal should not drive other gate terminals to
avoid multiple threshold drops.
Section 6.2
Static CMOS Design
261
Example 6.10 VTC of the pass transistor AND gate
The voltage transfer curve of a pass-transistor gate shows little resemblance to complementary CMOS. Consider the AND gate shown in Figure 6.36. Similar to complementary CMOS,
the VTC of pass transistor logic is data-dependent. For the case when B = VDD, the top pass
transistor is turned on, while the bottom one is turned off. In this case, the output just follows
the input A until the input is high enough to turn off the top pass transistor (i.e., reaches VDDVTn). Next consider the case when A=VDD, and B makes a transition from 0 → 1. Since the
inverter has a threshold of VDD/2, the bottom pass transistor is turned on till then and the output is close to zero. Once the bottom pass transistor turns off, the output follows the input B
minus a threshold drop. A similar behavior is observed when both inputs A and B transition
from 0 → 1.
Observe that a pure pass-transistor gate is not regenerative. A gradual signal degradation will be observed after passing through a number of subsequent stages. This can be remedied by the occasional insertion of a CMOS inverter. With the inclusion of an inverter in the
signal path, the VTC resembles the one of CMOS gates.
1.5µm/0.25µm
A
0.5µm/0.25µm
B
B=VDD, A = 0→VDD
Vout, V
0.5µm/0.25µm
B
2.0
1.0
A=Vdd, B = 0→VDD
A= B = 0→VDD
F = AB
0
0.5µm/0.25µm
0.00.0
1.0
2.0
Vin, V
Figure 6.36 Voltage Transfer Characteristic for the pass-transistor AND gate of Figure 6.33.
Pass-transistors require lower switching energy to charge up a node due to the
reduced voltage swing. For the pass transistor circuit in Figure 6.34 assume that the drain
voltage is at VDD and the gate voltage transitions to VDD. The output node charges from 0V
to VDD-VTn (assuming that node x was initially at 0V) and the energy drawn from the
power supply for charging the output of a pass transistor is given by:
E0 → 1 =
∫ P (t )dt = V ∫ isupply (t )dt = V
DD
0
( V DD – V Tn )
T
T
0
DD
∫
C L dV out = C L • V DD • ( V DD – V Tn )
(6.25)
0
While the circuit exhibits lower switching power, it may consumes static power
when the output is high—the reduced voltage level may be insufficient to turn off the
PMOS transistor of the subsequent CMOS inverter.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
262
A
A
B
B
Pass-Transistor
Network
F
A
A
B
B
Inverse
Pass-Transistor
Network
F
Chapter 6
(a) Basic concept
B
B
B
A
B
B
A
A
B
F = AB
A
B
F=A+B
F = AB
AND/NAND
B
A
F=A⊕B
A
A
B
B
F=A+B
OR/NOR
(b) Example pass-transistor networks
A
F=A⊕B
XOR/NXOR
Figure 6.37 Complementary pass-transistor logic (CPL).
Differential Pass Transistor Logic
For high performance design, a differential pass-transistor logic family, called CPL or
DPL, is commonly used. The basic idea (similar to DCVSL) is to accept true and complementary inputs and produce true and complementary outputs. A number of CPL gates
(AND/NAND, OR/NOR, and XOR/NXOR) are shown in Figure 6.37. These gates possess a number of interesting properties:
• Since the circuits are differential, complementary data inputs and outputs are always
available. Although generating the differential signals requires extra circuitry, the
differential style has the advantage that some complex gates such as XORs and
adders can be realized efficiently with a small number of transistors. Furthermore,
the availability of both polarities of every signal eliminates the need for extra inverters, as is often the case in static CMOS or pseudo-NMOS.
• CPL belongs to the class of static gates, because the output-defining nodes are
always connected to either VDD or GND through a low resistance path. This is
advantageous for the noise resilience.
• The design is very modular. In effect, all gates use exactly the same topology. Only
the inputs are permutated. This makes the design of a library of gates very simple.
More complex gates can be built by cascading the standard pass-transistor modules.
Section 6.2
Static CMOS Design
263
Example 6.11 Four-input NAND in CPL
Consider the implementation of a four-input AND/NAND gate using CPL. Based on the associativity of the boolean AND operation [A·B·C·D = (A·B)·(C·D)], a two-stage approach has
been adopted to implement the gate (Figure 6.38). The total number of transistors in the gate
(including the final buffer) is 14. This is substantially higher than previously discussed gates.
This factor, combined with the complicated routing requirements, makes this circuit style not
particularly efficient for this gate. One should, however, be aware of the fact that the structure
simultaneously implements the AND and the NAND functions, which might reduce the transistor count of the overall circuit.
B
B
Out
A
C
B
D
A
B
Y
X
X
X
B
D
X
D
Y
C
B
A
Out
X
X
A
C
D
D
Y
C
D
Y
Y
X
Out
Y
X
Out
Figure 6.38 Layout and schematics of four-input NAND-gate using CPL (the final inverter stage is
omitted). See also Colorplate 9.
In summary, CPL is a conceptually simple and modular logic style. Its applicability
depends strongly upon the logic function to be implemented. The availability of a simple
XOR as well of the ease of implementing some specific gate structures makes it attractive
for structures such as adders and multipliers. Some extremely fast and efficient implementations have been reported in that application domain [Yano90]. When considering CPL,
the designer should not ignore the implicit routing overhead of the complementary signals,
which is apparent in the layout of Figure 6.38.
Robust and Efficient Pass-Transistor Design
Unfortunately, differential pass-transistor logic, like single-ended pass-transistor logic,
suffers from static power dissipation and reduced noise margins, since the high input to
the signal-restoring inverter only charges up to VDD-VTn. There are several solutions proposed to deal with this problem as outlined below.
Solution 1: Level Restoration. A common solution to the voltage drop problem is the
use of a level restorer, which is a single PMOS configured in a feedback path (Figure
6.39). The gate of the PMOS device is connected to the output of the inverter, its drain
connected to the input of the inverter and the source to VDD. Assume that node X is at 0V
(out is at VDD and the Mr is turned off) with B = VDD and A = 0. If input A makes a 0 to VDD
transition, Mn only charges up node X to VDD-VTn. This is, however, enough to switch the
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
264
Chapter 6
output of the inverter low, turning on the feedback device Mr and pulling node X all the
way to VDD. This eliminates any static power dissipation in the inverter. Furthermore, no
static current path can exist through the level restorer and the pass-transistor, since the
restorer is only active when A is high. In summary, this circuit has the advantage that all
voltage levels are either at GND or VDD, and no static power is consumed.
Level restorer
VDD
VDD
Mr
B
A
M2
Out
X
Mn
M1
Figure 6.39 Level-restoring circuit.
While this solution is appealing in terms of eliminating static power dissipation, it
adds complexity since the circuit is now ratioed. The problem arises during the transition
of node X from high-to-low. The pass transistor network attempts to pull-down node X
while the level restorer pulls now X to VDD. Therefore, the pull-down device must be
stronger than the pull-up device in order to switch node X and the output. Some careful
transistor sizing is necessary to make the circuit function correctly. Assume the notation
R1 to denote the equivalent on-resistance of transistor M1, R2 for M2 , and so on. When Rr is
made too small, it is impossible to bring the voltage at node X below the switching threshold of the inverter. Hence, the inverter output never switches to VDD, and the level-restoring transistor stays on. This sizing problem can be reformulated as follows: the resistance
of Mn and Mr must be such that the voltage at node X drops below the threshold of the
inverter, VM = f(R1, R2). This condition is sufficient to guarantee a switching of the output
voltage Vout to VDD and a turning off of the level-restoring transistor.
VDD
VDD
B
Mr
M2
A=0
Mn
X
Out
M1
Figure 6.40 Transistor-sizing problem
for level-restoring circuit.
Example 6.12 Sizing of a Level Restorer
Analyzing the circuit as a whole is nontrivial, because the restoring transistor acts as a feedback device. One way to simplify the circuit for manual analysis is to open the feedback loop
and to ground the gate of the restoring transistor when determining the switching point (this is
a reasonable assumption, as the feedback only becomes effective once the inverter starts to
Section 6.2
Static CMOS Design
265
switch). Hence, Mr and Mn form a “pseudo-NMOS-like” configuration, with Mr the load transistor and Mn acting as a pull-down device to GND. Assume that the inverter M1, M2 is sized
to have the switching point at VDD/2 (NMOS: 0.5µm/0.25µm and PMOS: 1.5µm/0.25µm).
Therefore, node X must be pulled below VDD/2 in order to switch the inverter and shut off Mr.
This is confirmed in Figure 6.42, which shows the transient response as the size of the
level restorer is varied while keeping the size of Mn fixed (0.5µm/0.25µm). As the simulation
indicates, for sizes above 1.5µm/0.25µm, node X can’t be brought below the switching
threshold of the inverter and can’t switch the output. The detailed derivation of sizing requirement will be presented in the sequential design chapter. An important point to observe here is
that the sizing of Mr is critical for DC functionality, not just performance!
3.0
Voltage, V
2.0
W/Lr =1.75/0.25
W/Lr =1.50/0.25
1.0
W/Lr =1.0/0.25
0.0 0
100
200
W/Lr =1.25/0.25
300
400
Time, psec
Figure 6.41Transient response of the
circuit in Figure 6.40. A level restorer
that is too large can result in incorrect
evaluation.
500
Another concern is the influence of the level restorer on the switching speed of the
device. Adding the restoring device increases the capacitance at the internal node X, slowing down the gate. The rise time of the gate is further negatively affected, since, the levelrestoring transistor Mr fights the decrease in voltage at node X before being switched off.
On the other hand, the level restorer reduces the fall time, since the PMOS transistor, once
turned on, speeds the pull-up action.
Problem 6.5
Device Sizing in Pass Transistors
For the circuit shown in Figure 6.40, assume that the pull-down device consists of 6 pass transistors in series each with a device size of 0.5µm/0.25µm (replacing transistor Mn). Determine
the maximum W/L size for the level restorer transistor for correct functionality.
A modification of the level-restorer, applicable in differential networks and known
as swing-restored pass transistor logic, is shown in Figure 6.42. Instead of a simple
inverter or half-latch at the output of the pass transistor network, two back-to-back inverters, configured in a cross-coupled fashion, are used for level restoration and performance
improvement. Inputs are fed to both the gate and source/drain terminals as in the case of
conventional pass transistor networks. Figure 6.42 shows a simple XOR/XNOR gate of
three variables A, B and C. Notice that the complementary network can be optimized by
sharing transistors between the true and complementary outputs.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
266
VDD
VDD
M2
Out
M2
Out
Out
M1
M1
Complementary Output
NMOS Pass Transistor Network
Chapter 6
VDD
VDD
M2
M2
M1
M1
Out
C
C
C
C
B
B
B
B
A
Complementary inputs
to gate and source/drain
terminals
(a) general concept
A
A
A
(b) XOR/XNOR gate
Figure 6.42 Swing-restored pass transistor logic [Parameswar96].
Solution 2: Multiple-Threshold Transistors. A technology solution to the voltage-drop
problem associated with pass-transistor logic is the use of multiple-threshold devices.
Using zero threshold devices for the NMOS pass-transistors eliminates most of the threshold drop, and passes a signal close to VDD. Notice that even if the devices threshold was
implanted to be exactly equal to zero, the body effect of the device prevents a swing to
VDD. All devices other than the pass transistors (i.e., the inverters) are implemented using
standard high-threshold devices. The use of multiple-threshold transistors is becoming
more common, and involves simple modifications to existing process flows.
VDD
Zero (or low)-threshold transistor
VDD
0V
2.5 V
VDD
0V
Out
2.5 V
Figure 6.43 Static power consumption when
using zero-threshold pass-transistors.
The use of zero-threshold transistors can be dangerous due to the subthreshold currents that can flow through the pass-transistors, even if VGS is slightly below VT. This is
demonstrated in Figure 6.43, which points out a potential sneak dc-current path. While
these leakage paths are not critical when the device is switching constantly, they do pose a
significant energy-overhead when the circuit is in the idle state.
Section 6.2
Static CMOS Design
267
C
C
A
B
Figure 6.44 CMOS transmission gate.
A
B
C
C
(a) Circuit
(b) Symbolic representation
Solution 3: Transmission Gate Logic. The most widely-used solution to deal with the
voltage-drop problem is the use of transmission gates. It builds on the complementary
properties of NMOS and PMOS transistors: NMOS devices pass a strong 0 but a weak 1,
while PMOS transistors pass a strong 1 but a weak 0. The ideal approach is to use an
NMOS to pull-down and a PMOS to pull-up. The transmission gate combines the best of
both device flavors by placing a NMOS device in parallel with a PMOS device (Figure
6.44a). The control signals to the transmission gate (C and C) are complementary. The
transmission gate acts as a bidirectional switch controlled by the gate signal C. When C =
1, both MOSFETs are on, allowing the signal to pass through the gate. In short,
A = B
if
(6.26)
C=1
On the other hand, C = 0 places both transistors in cutoff, creating an open circuit between
nodes A and B. Figure 6.44b shows a commonly used transmission-gate symbol.
Consider the case of charging node B to VDD for the transmission gate circuit in Figure 6.45a. Node A is driven to VDD and transmission gate is enabled (C = 1 and C= 0). If
only the NMOS pass-device were present, node B charges up to VDD-VTn at which point
the NMOS device turns off. However, since the PMOS device is present and turned on
(VGSp = -VDD), charging continues all the way up to VDD. Figure 6.45b shows the opposite
case, this is discharging node B to 0. B is initially at VDD when node A is driven low. The
PMOS transistor by itself can only pull down node B to VTp at which point it turns off. The
parallel NMOS device however stays turned on (since its VGS = VDD) and pulls node B all
the way to GND. Though the transmission gate requires two transistors and more control
signals, it enables rail-to-rail swing.
C = VDD
C = VDD
B (initially at 0)
A=0
A = VDD
C=0
(a) charging node B
B (initially at VDD)
C=0
(a) discharging node B
Figure 6.45 Transmission gates
enable rail-to-rail switching
Transmission gates can be used to build some complex gates very efficiently. Figure
6.46 shows an example of a simple inverting two-input multiplexer. This gate either
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
268
Chapter 6
selects input A or B based on the value of the control signal S, which is equivalent to
implementing the following Boolean function:
F = (A ⋅ S + B ⋅ S)
(6.27)
A complementary implementation of the gate requires eight transistors instead of six.
S
S
VDD
S
VDD
A
M2
Out
F
S
M1
B
S
GND
S
A
S
B
Figure 6.46 Transmission gate multiplexer and its layout.
Another example of the effective use of transmission gates is the popular XOR circuit shown in Figure 6.47. The complete implementation of this gate requires only six
transistors (including the inverter used for the generation of B), compared to the twelve
transistors required for a complementary implementation. To understand the operation of
this circuit, we have to analyze the B = 0 and B = 1 cases separately. For B = 1, transistors
M1 and M2 act as an inverter while the transmission gate M3/M4 is off; hence F = AB. In
the opposite case, M1 and M2 are disabled, and the transmission gate is operational, or F =
AB. The combination of both results in the XOR function. Notice that, regardless of the
values of A and B, node F always has a connection to either VDD or GND and is hence a
low-impedance node. When designing static-pass transistor networks, it is essential to
adhere to the low-impedance rule under all circumstances. Other examples where transmission-gate logic is effectively used are fast adder circuits and registers.
B
B
M2
A
A
F
M1
B
B
M3/M4
Figure 6.47 Transmission gate XOR.
Section 6.2
Static CMOS Design
269
Performance of Pass-Transistor and Transmission Gate Logic
The pass-transistor and the transmission gate are, unfortunately, not ideal switches, and
have a series resistance associated with it. To quantify the resistance, consider the circuit
in Figure 6.48, which involves charging a node from 0 V to VDD. In this discussion, we use
the large-signal definition of resistance, which involves dividing the voltage across the
switch by the drain current. The effective resistance of the switch is modeled as a parallel
connection of the resistances Rn and Rp of the NMOS and PMOS devices, defined as (VDD
– Vout)/In and (VDD – Vout)/Ip, respectively. The currents through the devices are obviously
dependent on the value of Vout and the operating mode of the transistors. During the lowto-high transition, the pass-transistors traverse through a number of operation modes. For
low values of Vout, the NMOS device is saturated and the resistance is approximated as:
V
–V
V
–V
DD
out
DD
out
R n = ------------------------------- = -------------------------------------------------------------------------------------------------------------------------------I
2
V DSAT
N
W
k′ ----- ( V
–V
– V )V
– -------------------
n L N DD
out
Tn DSAT
2
V
–V
DD
out
≈ -----------------------------------------------------------------------------k n ( V DD – V out – V Tn )V DSAT
(6.28)
The resistance goes up for increasing values of Vout, and approaches infinity when Vout
reaches VDD-VTn, this is when the device shuts off. Similarly, we can analyze the behavior
of the PMOS transistor. When Vout is small, the PMOS is saturated, but it enters the linear
mode of operation for Vout approaching VDD, giving the following approximated resistance:
R
p
V DD – V out
V DD – V out
= ------------------------------- = -------------------------------------------------------------------------------------------------------------------------------------IP
( V out – V DD ) 2
k p ⋅ ( – V DD – V Tp ) ( V out – V DD ) – --------------------------------
2
1
≈ ------------------------------------------
k p ( V DD – V Tp )
(6.29)
The simulated value of Req = Rp || Rn as a function of Vout is plotted in Figure 6.48. It
can be observed that Req is relatively constant (≈ 8kΩ in this particular case). The same is
true in other design instances (for instance, when discharging CL). When analyzing transmission-gate networks, the simplifying assumption that the switch has a constant resistive
value is therefore acceptable.
Problem 6.6
Equivalent Resistance During Discharge
Determine the equivalent resistance by simulation for the high-to-low transition of a transmission gate (this is, produce a plot similar to the one presented in Figure 6.48).
An important consideration is the delay associated with a chain of transmission
gates. Figure 6.49 shows a chain of n transmission gates. Such a configuration often
occurs in circuits such as adders or deep multiplexors. Assume that all transmission gates
are turned on and a step is applied at the input. To analyze the propagation delay of this
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
270
Chapter 6
30
2.5 V
Resistance, ohms
Rn
Rn
Rp
20
Vout
2.5 V
Rp
0V
10
Rn || Rp
0
0.0
1.0
2.0
Vout, V
Figure 6.48 Simulated equivalent resistance of transmission gate for low-to-high transition
(for (W/L)n = (W/L)p = 0.5µm/0.25µm). A similar response for overall resistance is obtained for the
high-to-low transition
network, the transmission gates are replaced by their equivalent resistances Req. This produces the network of Figure 6.49b.
The delay of a network of n transmission gates in sequence can be estimated using the
Elmore approximation (see Chapter 4):
n
t p ( V n ) = 0.69
∑ CR
k=0
eq k
n( n + 1)
= 0.69CR eq -------------------2
(6.30)
This means that the propagation delay is proportional to n2 and increases rapidly with the
number of switches in the chain.
2.5
2.5
V1
In
C
0
2.5
Vi
Vi-1
C
0
2.5
Vi+1
0
Vn–1
C
C
Vn
C
0
(a) A chain of transmission gates
Req
In
Req
V1
C
Req
Vi
C
(b) Equivalent RC network
Figure 6.49 Speed optimization in transmission-gate networks.
Vi+1
C
Req
Vn-1
C
Vn
C
Section 6.2
Static CMOS Design
271
Example 6.13 Delay through 16 transmission gates
Consider 16 cascaded minimum-sized transmission gates, each with an average resistance of
8 kΩ. The node capacitance consists of the capacitance of two NMOS and PMOS devices
(junction and gate). Since the gate inputs are assumed to be fixed, there is no Miller multiplication. The capacitance can be calculated to be approximately 3.6 fF for the low-to-high transition. The delay is given by:
t
p
= 0.69 ⋅ CR
eq
( 16 + 1 ) ≈ 2.7ns
n ( n + 1 ) = 0.69 ⋅ ( 3.6fF ) ( 8KΩ ) 16
--------------------------------------------
2
2
(6.31)
The transient response for this particular example is shown in Figure 6.50. The simulated delay is 2.7ns. It is remarkable that a simple RC model predicts the delay so accurately.
It is also clear that the use of long pass transistor chains causes significant delay degradation.
3.0
Out2
Voltage, V
Out1
2.0
Out16
1.0
0.0 0
2
4
6
Time (ns)
8
10
Figure 6.50 Transient response of 16
transmission gates cascaded in series.
The most common approach for dealing with the long delay is to break the chain and
by inserting buffers every m switches (Figure 6.51). Assuming a propagation delay tbuf for
each buffer, the overall propagation delay of the transmission-gate/buffer network is then
computed as follows,
n
m(m + 1)
n
t p = 0.69 ---- CR eq ----------------------- + ---- – 1 t buf
m
2
m
n
n(m + 1)
= 0.69 CR eq --------------------- + ---- – 1 t buf
m
2
(6.32)
The resulting delay exhibits only a linear dependence on the number of switches n, in contrast to the unbuffered circuit, which is quadratic in n. The optimal number of switches
mopt between buffers can be found by setting the derivative
t pbuf
m opt = 1.7 ----------CR eq
∂t p
to 0, which yields
∂m
(6.33)
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
272
Chapter 6
Obviously, the number of switches per segment grows with increasing values of tbuf. In
current technologies, mopt is typically around 3.
m
Req
Req
Req
Req
Req
Req
In
C
CC
C
C
CC
C
Figure 6.51 Breaking up long transmission gate chains by inserting buffers.
Example 6.14 Transmission Gate Chain
Consider the same 16 transmission gate chain. The buffers shown in Figure 6.51 can be
implemented as inverters (instead of two cascaded inverters). In some cases, it might be necessary to add an extra inverter to produce the correct polarity. Assuming that each inverter is
sized such that the NMOS is 0.5µm/0.25µm and PMOS is 0.5µm /0.25µm, Eq. (6.33) predicts
that an inverter must be inserted every 3 transmission gates. The simulated delay when placing an inverter every two transmission gates equals 154 psec, for every three transmission
gates is 154 psec, and for four transmission gates is 164 psec. The insertion of buffering
inverters reduces the delay with a factor of almost 2.
CAUTION: Although many of the circuit styles discussed in the previous sections sound
very exciting, and might be superior to static CMOS in many respects, none of them has
the robustness and ease of design of complementary CMOS. Therefore, use them sparingly and with caution. For designs that have no extreme area, complexity, or speed constraints, complementary CMOS is the recommended design style.
6.3
Dynamic CMOS Design
It was noted earlier that static CMOS logic with a fan-in of N requires 2N devices. A variety of approaches were presented to reduce the number of transistors required to implement a given logic function including pseudo-NMOS, pass transistor logic, etc. The
pseudo-NMOS logic style requires only N + 1 transistors to implement an N input logic
gate, but unfortunately it has static power dissipation. In this section, an alternate logic
style called dynamic logic is presented that obtains a similar result, while avoiding static
power consumption. With the addition of a clock input, it uses a sequence of precharge
and conditional evaluation phases.
6.3.1
Dynamic Logic: Basic Principles
The basic construction of an (n-type) dynamic logic gate is shown in Figure 6.52a. The
PDN (pull-down network) is constructed exactly as in complementary CMOS. The opera-
Section 6.3
Dynamic CMOS Design
273
tion of this circuit is divided into two major phases: precharge and evaluation, with the
mode of operation determined by the clock signal CLK.
VDD
VDD
CLK
Mp
CLK
Mp
Out
Out
CL
In1
A
C
PDN
In2
B
In3
CLK
Me
(a) n-type network
CLK
Me
(b) Example
Figure 6.52 Basic concepts of a dynamic gate.
Precharge
When CLK = 0, the output node Out is precharged to VDD by the PMOS transistor Mp.
During that time, the evaluate NMOS transistor Me is off, so that the pull-down path is disabled. The evaluation FET eliminates any static power that would be consumed during the
precharge period (this is, static current would flow between the supplies if both the pulldown and the precharge device were turned on simultaneously).
Evaluation
For CLK = 1, the precharge transistor Mp is off, and the evaluation transistor Me is turned
on. The output is conditionally discharged based on the input values and the pull-down
topology. If the inputs are such that the PDN conducts, then a low resistance path exists
between Out and GND and the output is discharged to GND. If the PDN is turned off, the
precharged value remains stored on the output capacitance CL, which is a combination of
junction capacitances, the wiring capacitance, and the input capacitance of the fan-out
gates. During the evaluation phase, the only possible path between the output node and a
supply rail is to GND. Consequently, once Out is discharged, it cannot be charged again till
then next precharge operation. The inputs to the gate can therefore make at most one transition during evaluation. Notice that the output can be in the high-impedance state during
the evaluation period if the pull-down network is turned off. This behavior is fundamentally different from the static counterpart that always has a low resistance path between the
output and one of the power rails.
As as an example, consider the circuit shown in Figure 6.52b. During the precharge
phase (CLK=0), the output is precharged to VDD regardless of the input values since the
evaluation device is turned off. During evaluation (CLK=1), a conducting path is created
274
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
Chapter 6
between Out and GND if (and only if) A·B+C is TRUE. Otherwise, the output remains at
the precharged state of VDD. The following function is thus realized:
Out = CLK + ( A ⋅ B + C ) ⋅ CLK
(6.34)
A number of important properties can be derived for the dynamic logic gate:
• The logic function is implemented by the NMOS pull-down network. The construction of the PDN proceeds just as it does for static CMOS.
• The number of transistors (for complex gates) is substantially lower than in the
static case: N + 2 versus 2N.
• It is non-ratioed. The sizing of the PMOS precharge device is not important for realizing proper functionality of the gate. The size of the precharge device can be made
large to improve the low-to-high transition time (of course, at a cost to the high-tolow transition time). There is however, a trade-off with power dissipation since a
larger precharge device directly increases clock-power dissipation.
• It only consumes dynamic power. Ideally, no static current path ever exists between
VDD and GND. The overall power dissipation, however, can be significantly higher
compared to a static logic gate.
• The logic gates have faster switching speeds. There are two main reasons for this.
The first (obvious) reason is due to the reduced load capacitance attributed to the
lower number of transistors per gate and the single-transistor load per fan-in. Second, the dynamic gate does not have short circuit current, and all the current provided by the pull-down devices goes towards discharging the load capacitance.
The low and high output levels VOL and VOH are easily identified as GND and VDD
and are not dependent upon the transistor sizes. The other VTC parameters are dramatically different from static gates. Noise margins and switching thresholds have been
defined as static quantities that are not a function of time. To be functional, a dynamic gate
requires a periodic sequence of precharges and evaluations. Pure static analysis, therefore,
does not apply. During the evaluate period, the pull-down network of a dynamic inverter
starts to conduct when the input signal exceeds the threshold voltage (VTn) of the NMOS
pull-down transistor. Therefore, it is reasonable to set the switching threshold (VM) as well
as VIH and VIL of the gate equal to VTn. This translates to a low value for the NML.
Design Consideration
It is also possible to implement dynamic logic using a complimentary approach, where the output node is connected by a pre-discharge NMOS transistor to GND, and the evaluation PUN
network is implemented in PMOS. The operation is similar: during precharge, the output node
is discharged to GND. During evaluation, the output is conditionally charged to VDD. This ptype dynamic gate has the disadvantage of being slower than the n-type due to the lower current drive of the PMOS transistors.
Section 6.3
Dynamic CMOS Design
6.3.2
275
Speed and Power Dissipation of Dynamic Logic
The main advantages of dynamic logic are increased speed and reduced implementation
area. Fewer devices to implement a given logic function implies that the overall load
capacitance is much smaller. The analysis of the switching behavior of the gate has some
interesting peculiarities to it. After the precharge phase, the output is high. For a low input
signal, no additional switching occurs. As a result, tpLH = 0! The high-to-low transition, on
the other hand, requires the discharging of the output capacitance through the pull-down
network. Therefore tpHL is proportional to CL and the current-sinking capabilities of the
pull-down network. The presence of the evaluation transistor slows the gate somewhat, as
it presents an extra series resistance. Omitting this transistor, while functionally not forbidden, may result in static power dissipation and potentially a performance loss.
The above analysis is somewhat unfair, because it ignores the influence of the precharge time on the switching speed of the gate. The precharge time is determined by the
time it takes to charge CL through the PMOS precharge transistor. During this time, the
logic in the gate cannot be utilized. However, very often, the overall digital system can be
designed in such a way that the precharge time coincides with other system functions. For
instance, the precharge of the arithmetic unit in a microprocessor can coincide with the
instruction decode. The designer has to be aware of this “dead zone” in the use of dynamic
logic, and should carefully consider the pros and cons of its usage, taking the overall system requirements into account.
Example 6.15 A Four-Input Dynamic NAND Gate
Figure 6.53 shows the design of a four-input NAND example designed using the dynamic-circuit style. Due to the dynamic nature of the gate, the derivation of the voltage-transfer characteristic diverges from the traditional approach. As we had discussed above, we will assume
that the switching threshold of the gate equals the threshold of the NMOS pull-down transistor. This results in asymmetrical noise margins, as shown in Table 6.9.
The dynamic behavior of the gate is simulated with SPICE. It is assumed that all inputs
are set high as the clock transitions high. On the rising edge of the clock, the output node is
discharged. The resulting transient response is plotted in Figure 6.53, and the propagation
delays are summarized in Table 6.9. The duration of the precharge cycle can be adjusted by
changing the size of the PMOS precharge transistor. Making the PMOS too large should be
avoided, however, as it both slows down the gate, and increases the capacitive load on the
clock line. For large designs, the latter factor might become a major design concern as the
clock load can become excessive and hard to drive.
Table 6.9
The dc and ac parameters of a four-input dynamic NAND.
Transistors
VOH
VOL
VM
NMH
NML
tpHL
tpLH
tpre
6
2.5 V
0V
VTN
2.5-VTN
VTN
110 psec
0 nsec
83psec
As mentioned earlier, the static parameters are time-dependent. To illustrate this, consider the four input NAND gate with all inputs tied together, and making a partial low-to-high
transition. Figure 6.54 shows a transient simulation of the output voltage for three different
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
276
Chapter 6
VDD
CLK
2.5
Out
In1
Voltage
Out
In2
1.5
IN &
CLK
0.5
In3
-0.5
In4
0
0.5
1
Time, ns
Figure 6.53 Schematic and transient response of a four-input
dynamic NAND gate.
CLK
input transitions—to 0.45V, 0.5V and 0.55V, respectively. Above, we have defined the
switching threshold of the dynamic gate as the device threshold. However, notice that the
amount by which the output voltage drops is a strong function of the input voltage and the
available evaluation time. The noise voltage needed to corrupt the signal has to be larger if the
evaluation time is short. In other words, the switching threshold is really a function of the
evaluation time.
When evaluating the power dissipation of a dynamic gate, it would appear that
dynamic logic presents a significant advantage. There are three reasons for this. First, the
physical capacitance is lower since dynamic logic uses fewer transistors to implement a
given function. Also, the load seen for each fanout is one transistor instead of two. Second, dynamic logic gates by construction can at most have one transition per clock cycle.
Glitching (or dynamic hazards) does not occur in dynamic logic. Finally, dynamic gates
do not exhibit short circuit power since the pull-up path is not turned on when the gate is
evaluating.
While these arguments are generally true, they are offset by other considerations: (i)
the clock power of dynamic logic can be significant, particularly since the clock node has
3.0
CLK
Voltage, V
2.0
Vout
Vout
(VG=0.55) (VG=0.5)
1.0
VG
0.0
-1.0
Vout
(VG=0.45)
0
20
40
60
Time, nsec
80
100
Figure 6.54 Effect of an input glitch on the
output. The switching threshold depends on the
time for evaluation. A larger glitch is acceptable
if the evaluation phase is smaller. In this
example, the input glitches high during
evaluation and stays high during the whole
period.
Section 6.3
Dynamic CMOS Design
277
a guaranteed transition on every single clock cycle; (ii) the number of transistors is higher
than the minimal set required for implementing the logic; (iii) short-circuit power may
exist when leakage-combatting devices are added (as will be discussed further); (iv) and,
most importantly, dynamic logic generally displays a higher switching activity due to the
periodic precharge and discharge operations. Earlier, the transition probability for a static
gate was shown to be p0 p1 = p0 (1-p0). For dynamic logic, the output transition probability
does not depend on the state (history) of the inputs, but rather on the signal probabilities
only. For an n-tree dynamic gate, the output makes a 0→1 transition during the precharge
phase only if the output was discharged during the preceding evaluate phase. The 0→1
transition probability for an n-type dynamic gate hence equals
α0 → 1 = p0
(6.35)
where p0 is the probability that the output is zero. This number is always larger or equal to
p0 p 1. For uniformly distributed inputs, the transition probability for an N-input gate is:
N
α0 → 1 = ------02
(6.36)
N
where N0 is the number of zero entries in the truth table of the logic function.
Example 6.16 Activity estimation in dynamic logic
To illustrate the increased activity for a dynamic gate, once again consider a 2 input NOR
gate. An n-tree dynamic implementation is shown in Figure 6.55 along with its static counterpart. For equi-probable inputs, there is then a 75% probability that the output node of the
dynamic gate will discharge immediately after the precharge phase, implying that the activity
for such a gate equals 0.75 (i.e PNOR= 0.75 CLVdd2fclk). The corresponding activity is a lot
smaller, 3/16, for a static implementation. For a dynamic NAND gate, the transition probability is 1/4 (since there is a 25% probability the output will be discharged) while it is 3/16 for a
static implementation. Though these example illustrate that the switching activity of dynamic
logic is generally higher, it should be noted that dynamic logic has lower physical capacitance. Both factors must be accounted for when choosing a logic style.
VDD
VDD
CLK
A
CL
B
A
B
Figure 6.55 Static NOR versus n-type
dynamic NOR.
CL
A
B
CLK
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
278
Chapter 6
Problem 6.7 Activity Computation
For the 4-input dynamic NAND gate, compute the activity factor with the following assumption for the inputs. Assume that the inputs are independent and pA=1 = 0.2, pB=1 = 0.3, pC=1 =
0.5, and pD=1 = 0.4.
6.3.3
Issues in Dynamic Design
Dynamic logic clearly can result in high performance solutions compared to static circuits.
However, there are several important considerations that must be taken into account if one
wants dynamic circuits to function properly. This include charge leakage, charge sharing,
backgate (and in general capacitive) coupling, and clock feedthrough. Some of these
issues are highlighted in this section.
Charge Leakage
The operation of a dynamic gate relies on the dynamic storage of the output value on a
capacitor. If the pull-down network is off, the output should ideally remain at the precharged state of VDD during the evaluation phase. However, this charge gradually leaks
away due to leakage currents, eventually resulting in a malfunctioning of the gate. Figure
6.56a shows the sources of leakage for the basic dynamic inverter circuit.
VDD
CLK
CLK
(4)
Mp
(3)
Out
(1)
A=0
M1
(2)
CLK
CL
t
Vout
Precharge
Evaluate
Me
t
(a) Leakage sources
(b) Effect on waveforms
Figure 6.56 Leakage issues in dynamic circuits.
Source 1 and 2 are the reverse-biased diode and sub-threshold leakage of the
NMOS pull-down device M1, respectively. The charge stored on CL will slowly leak away
due these leakage sources, assuming that the input is at zero during evaluation. Charge
leakage causes a degradation in the high level (Figure 6.56b). Dynamic circuits therefore
require a minimal clock rate, which is typically on the order of a few kHz. This makes the
usage of dynamic techniques unattractive for low performance products such as watches,
or processors that use conditional clocks (where there are no guarantees on minimum
clock rates). Note that the PMOS precharge device also contributes some leakage current
Section 6.3
Dynamic CMOS Design
279
due to the reverse bias diode (source 3) and the subthreshold conduction (source 4). To
some extent, the leakage current of the PMOS counteracts the leakage of the pull-down
path. As a result the output voltage is going to be set by the resistive divider composed of
the pull-down and pull-up paths.
Example 6.17 Leakage in dynamic circuits
Consider the simple inverter with all devices set at 0.5µm/0.25µm. Assume that the input is
low during the evaluation period. Ideally, the output should remain at the precharged state of
VDD. However, as seen from Figure 6.57 the output voltage drops. Once the output drops
below the switching threshold of the fan-out logic gate, the output is interpreted as a low voltage. Notice that the output settles to an intermediate voltage. This is due to the leakage current
provided by the PMOS pull-up.
3.0
Voltage, V
2.0
Out
1.0
Figure 6.57 Impact of charge leakage. The
output settles to an intermediate voltage
determined by a resistive divider of the pulldown and pull up devices.
CLK
0.00
10
20
time, ms
30
40
Leakage is caused by the high impedance state of the output node during the evaluate mode, when the pull down path is turned off. The leakage problem van be counteracted
by reducing the output impedance on the output node during evaluation. This is often done
by adding a bleeder transistor as shown in Figure 6.58a. The only function of the
bleeder—a pseudo-NMOS-like pull-up device—is to compensate for the charge lost due
to the pull-down leakage paths. To avoid the ratio problems associated with this style of
circuit and the associated static power consumption, the bleeder resistance is made high,
or, in other words, the device is kept small. This allows the (strong) pull-down devices to
VDD
CLK
Mp
VDD
Mbl
CLK
Mbl
Mp
Out
Out
A
Ma
A
Ma
B
Mb
B
Mb
CLK
Me
CLK
Me
(a)
(b)
Figure 6.58 Static bleeders
compensates for the charge-leakage.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
280
Chapter 6
lower the Out node substantially below the switching threshold of the inverter. Often, the
bleeder is implemented in a feedback configuration to eliminate the static power dissipation (Figure 6.58b).
Charge Sharing
Another important concern in dynamic logic is the impact of charge sharing. Consider the
circuit of Figure 6.59. During the precharge phase, the output node is precharged to VDD.
Assume that all inputs are set to 0 during precharge, and that the capacitance Ca is discharged. Assume further that input B remains at 0 during evaluation, while input A makes
a 0 → 1 transition, turning transistor Ma on. The charge stored originally on capacitor CL
is redistributed over CL and Ca. This causes a drop in the output voltage, which cannot be
recovered due to the dynamic nature of the circuit.
VDD
CLK
Mp
Out
CL
Ma
A
B=0
CLK
Mb
Me
X
Ca
Cb
Figure 6.59 Charge sharing in dynamic networks.
The influence on the output voltage is readily calculated. Under the above assumptions, the following initial conditions are valid: Vout(t = 0) = VDD and VX(t = 0) = 0. Two
possible scenarios must be considered:
1. ∆Vout < VTn — In this case, the final value of VX equals VDD – VTn(VX). Charge conservation yields
C L V DD = C L V out ( t ) + C a [ V DD – V Tn ( V X ) ]
or
∆V out = V out ( t ) – V DD
(6.37)
C
= – -----a- [ V DD – V Tn ( V X ) ]
CL
2. ∆Vout > VTn — Vout and VX reach the same value:
Ca
∆V out = – V DD ----------------- C a + C L
(6.38)
Which of the above scenarios is valid is determined by the capacitance ratio. The boundary condition between the two cases can be determined by setting ∆Vout equal to VTn in Eq.
(6.38), yielding
Section 6.3
Dynamic CMOS Design
281
V Tn
C
-----a- = -----------------------V DD – V Tn
CL
(6.39)
Overall, it is desirable to keep the value of ∆Vout below |VTp|. The output of the dynamic
gate might be connected to a static inverter, in which case the low level of Vout would
cause static power consumption. One major concern is circuit malfunction if the output
voltage is brought below the switching threshold of the gate it drives.
Example 6.18 Charge-Sharing
Let us consider the impact of charge sharing on the dynamic logic gate shown in Figure 6.60,
which implements a 3-input EXOR function y = A ⊕ B ⊕ C. The first question to be resolved
is what conditions cause the worst-case voltage drop on node y. For simplicity, ignore the
load inverter, and assume that all inputs are low during the precharge operation and that all
isolated internal nodes (Va, Vb, Vc, and Vd) are initially at 0V.
Inspection of the truth table for this particular logic function shows that the output
stays high for 4 out of 8 cases. The worst-case change in output is obtained by exposing the
maximum amount of internal capacitance to the output node during the evaluation period.
This happens for A B C or A B C. The voltage change can then be obtained by equating the
initial charge with the final charge as done with equation Eq. (6.38), yielding a worst-case
change of 30/(30+50) * 2.5V = 0.94V. To ensure that the circuit functions correctly, the
switching threshold of the connecting inverter should be placed below 2.5- 0.94 = 1.56V.
The most common and effective approach to deal with the charge redistribution is to
also precharge critical internal nodes, as is shown in Figure 6.61. Since the internal nodes
are charged to VDD during precharge, charge sharing does not occur. This solution obviously comes at the cost of increased area and capacitance.
Capacitive Coupling
The high impedance of the output node makes the circuit very sensitive to crosstalk
effects. A wire routed over a dynamic node may couple capacitively and destroy the state
of the floating node. Another equally important form of capacitive coupling is the backgate (or output-to-input) coupling.Consider the circuit shown in Figure 6.62 in which a
dynamic two-input NAND gate drives a static NAND gate. A transition in the input In of
CLK
y
Cy = 50 fF
A
A
a
Ca = 15 fF
VDD = 2.5V
Load Inverter
b
B
B
B
c
Cc = 15 fF
C
CLK
C
B
Cb = 15 fF
d
Cd = 10 fF
Figure 6.60 Example illustrating the
charge sharing effect in dynamic logic.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
282
Chapter 6
VDD
Mbl
Mp
CLK
CLK
Out
A
Ma
B
Mb
CLK
Me
Figure 6.61 Dealing with charge-sharing by precharging
internal nodes. An NMOS precharge transistor may also be
used, but this requires an inverted clock.
the static gate may cause the output of the gate (Out2) to go low. This output transition
couples capacitively to the other input of the gate, the dynamic node Out1, through the
gate-source and gate-drain capacitances of transistor M4. A simulation of this effect is
shown in Figure 6.63, and demonstrates that the output of the dynamic gate can drop significantly. This further causes the output of the static NAND gate not to drop all the way
down to 0V, and a small amount of static power is dissipated. If the voltage drop is large
enough, the circuit can evaluate incorrectly, and the NAND output may not go low. When
designing and laying out dynamic circuits, special care is needed to minimize capacitive
coupling.
VDD
CLK
VDD
M6
M5
Mp
Out1
A=0
VDD
M1
Out2
CL1
M4
B=0
CL2
In
M2
M3
CLK
Me
Figure 6.62 Example demonstrating
the effect of backgate coupling.
Clock-Feedthrough
A special case of capacitive coupling is clock-feedthrough, an effect caused by the capacitive coupling between the clock input of the precharge device and the dynamic output
node. The coupling capacitance consists of the gate-to-drain capacitance of the precharge
device, and includes both the overlap and the channel capacitances. This capacitive coupling causes the output of the dynamic node to rise above VDD on the low-to-high transition of the clock, assuming that the pull-down network is turned off. Subsequently, the fast
rising and falling edges of the clock couple onto the signal node, as is quite apparent in the
simulation of Figure 6.63.
The danger of clock feedthrough is that it may cause the (normally reverse-biased)
junction diodes of the precharge transistor to become forward-biased. This causes electron
Section 6.3
Dynamic CMOS Design
due to clock feedthrough
3.0
Out1
2.0
Voltage, V
283
CLK
1.0
IN
Out2 (does not discharge
to gnd)
0.0
-1.0
0
2
4
Figure 6.63 Clock feedthrough effect.
6
Time, ns
injection into the substrate, which can be collected by a nearby high impedance node in
the 1 state, eventually resulting in faulty operation. CMOS latchup might be another result
of this injection. For all purposes, high-speed dynamic circuits should be carefully simulated to ensure that clock-feedthrough effects stay within bounds.
All the above considerations demonstrate that the design of dynamic circuits is
rather tricky and requires extreme care. It should therefore only be attempted when high
performance is required.
6.3.4
Cascading Dynamic Gates
Besides the signal integrity issues, there is one major catch that complicates the design of
dynamic circuits: straightforward cascading of dynamic gates to create more complex
structures does not work. The problem is best illustrated with the two cascaded n-type
dynamic inverters, shown in Figure 6.64a. During the precharge phase (i.e., CLK =0), the
outputs of both inverters are precharged to VDD. Assume that the primary input In makes a
0 → 1 transition (Figure 6.64b). On the rising edge of the clock, output Out1 starts to discharge. The second output should remain in the precharged state of VDD as its expected
VDD
VDD
Mp
CLK
CLK
V
Mp
CLK
In
Out2
Out1
Out1
VTn
In
∆V
Out2
CLK
CLK
Me
Me
(a)
Figure 6.64 Cascade of dynamic n−type blocks.
t
(b)
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
284
Chapter 6
value is 1 (Out1 transitions to 0 during evaluation). However, there is a finite propagation
delay for the input to discharge Out1 to GND. Therefore, the second output also starts to
discharge. As long as Out1 exceeds the switching threshold of the second gate, which
approximately equals VTn, a conducting path exists between Out2 and GND, and precious
charge is lost at Out2. The conducting path is only disabled once Out1 reaches VTn, and
turns off the NMOS pull-down transistor. This leaves Out2 at an intermediate voltage
level. The correct level will not be recovered, as dynamic gates rely on capacitive storage
in contrast to static gates, which have dc restoration. The charge loss leads to reduced
noise margins and potential malfunctioning.
The cascading problem arises because the outputs of each gate—and hence the
inputs to the next stages—are precharged to 1. This may cause inadvertent discharge in the
beginning of the evaluation cycle. Setting all the inputs to 0 during precharge addresses
that concern. When doing so, all transistors in the pull-down network are turned off after
precharge, and no inadvertent discharging of the storage capacitors can occur during evaluation. In other words, correct operation is guaranteed as long as the inputs can only
make a single 0 → 1 transition during the evaluation period2. Transistors are only be
turned on when needed, and at most once per cycle. A number of design styles complying
with this rule have been conceived. The two most important ones are discussed below.
Domino Logic
Concept. A Domino logic module [Krambeck82] consists of an n-type dynamic logic
block followed by a static inverter (Figure 6.65). During precharge, the output of the ntype dynamic gate is charged up to VDD, and the output of the inverter is set to 0. During
evaluation, the dynamic gate conditionally discharges, and the output of the inverter
makes a conditional transition from 0 → 1. If one assumes that all the inputs of a Domino
gate are outputs of other Domino gates3, then it is ensured that all inputs are set to 0 at the
end of the precharge phase, and that the only transitions during evaluation are 0 → 1 transitions. The formulated rule is hence obeyed. The introduction of the static inverter has the
additional advantage that the fan-out of the gate is driven by a static inverter with a lowimpedance output, which increases noise immunity. The buffer furthermore reduces the
capacitance of the dynamic output node by separating internal and load capacitances.
Consider now the operation of a chain of Domino gates. During precharge, all inputs
are set to 0. During evaluation, the output of the first Domino block either stays at 0 or
makes a 0 → 1 transition, affecting the second gate. This effect might ripple through the
whole chain, one after the other, similar to a line of falling dominoes—hence the name.
Domino CMOS has the following properties:
• Since each dynamic gate has a static inverter, only non-inverting logic can be implemented. Although there are ways to deal with this, as is discussed in a subsequent
section, this is major limiting factor, and pure Domino design has become rare.
2
3
This ignores the impact of charge distribution and leakage effects, discussed earlier.
It is required that all other inputs that do not fall under this classification (for instance, primary inputs)
stay constant during evaluation.
Section 6.3
Dynamic CMOS Design
285
VDD
CLK
VDD
Mp
Mp
CLK
Out2
Out1
In1
PDN
In2
In4
PDN
In3
CLK
Me
Me
CLK
Figure 6.65 DOMINO CMOS logic.
• Very high speeds can be achieved: only a rising edge delay exists, while tpHL equals
zero. The inverter can be sized to match the fan-out, which is already much smaller
than in the complimentary static CMOS case, as only a single gate capacitance has
to be accounted for per fan-out gate.
Since the inputs to a Domino gate are low during precharge, it is tempting to eliminate the evaluation transistor as this would reduce clock load and increase pull-down
drive. However, eliminating the evaluation device extends the precharge cycle: the precharge now has to ripple through the logic network as well. Consider the logic network
shown in Figure 6.66, where the evaluation devices have been eliminated. If the primary
input In1 is 1 during evaluation, the output of each dynamic gate is 0 and the output of
each static inverter is 1. On the falling edge of the clock, the precharge operation is started.
Assume further that In1 makes a high-to-low transition. The input to the second gate is initially high, and it takes two gate delays before In2 is driven low. During that time, the second gate cannot precharge its output, as the pull-down network is fighting the precharge
device. Similarly, the third gate has to wait till the second gate precharges before it can
start precharging, etc. Therefore the time taken to precharge the logic circuit is equal to its
critical path. Another important negative is the extra power dissipation when both pull-up
and pull-down devices are on. It is therefore good practice to always utilize evaluation
devices.
Dealing with the Non-inverting Property of Domino Logic. A major limitation in
Domino logic is that only non-inverting logic can be implemented. This requirement has
VDD
CLK
Mp
In1
1->0
VDD
CLK
VDD
Mp
CLK
Mp
Out1
Out2
Outn
0->1
0->1
0->1
In2
1->0
In3
Inn
1->0
1->0
Figure 6.66 Effect of ripple precharge when the evaluation transistor is removed. The
circuit also exhibits static power dissipation.
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
286
Chapter 6
limited the widespread use of pure Domino logic. There are several ways to deal with the
non-inverting logic requirement. Figure 6.67 shows one approach to the problem—reorganizing the logic using simple boolean transforms such as De Morgan’s Law. Unfortunately, this sort of optimization is not always possible, and more general schemes may
have to be used.
Domino AND
A
B
X
C
D
E
Y
F
G
H
A
B
X
C
D
E
F
G
H
Y
Domino AND-OR
Domino OR
(a) before logic transformation
(b) after logic transformation
Figure 6.67 Restructuring logic to enable implementation using non-inverting Domino Logic.
A general but expensive approach to solving the problem is the use of differential
logic. Dual-rail Domino is similar in concept to the DCVSL structure discussed earlier,
but uses a precharged load instead of a static cross-coupled PMOS load. Figure 6.68
shows the circuit schematic of an AND/NAND differential logic gate. Note that all inputs
come from other differential Domino gates, and are low during the precharge phase, while
making a conditional 0→1 transition during evaluation. Using differential Domino, it is
possible to implement any arbitrary function. This comes at the expense of an increased
power dissipation, since a transition is guaranteed every single clock cycle regardless of
the input values—either O or O must make a 0→1 transition. The function of transistors
Mf1 and Mf2 is to keep the circuit static when the clock is high for extended periods of time
(bleeder). Notice that this circuit is not ratioed, even in the presence of the PMOS pull-up
devices! Due to its high-performance, this differential approach is very popular, and is
used in several commercial microprocessors.
Optimization of Domino Logic Gates. Several optimizations can be performed on
Domino logic gates. The most obvious performance optimization involves the sizing of
VDD
VDD
Mp
CLK
Mf1
Mp
Mf2
O = AB
CLK
O = AB
A
M1
A
B
M2
CLK
Me
B
Figure 6.68 Simple dual rail (differential)
Domino logic gate.
Section 6.3
Dynamic CMOS Design
287
the transistors in the static inverter. With the inclusion of the evaluation devices in Domino circuits, all gates precharge in parallel, and the precharge operation takes only two
gate delays—charging the output of the dynamic gate to VDD, and driving the inverter output low. The critical path during evaluation goes through the pull-down path of the
dynamic gate, and the PMOS pull-up transistor of the static inverter. Therefore, to speed
up the circuit during evaluation, the beta ratio of the static inverter should be made high so
that its switching threshold is close to VDD. This can be accomplished by using a small
(minimum) sized NMOS and a large PMOS device. The minimum-sized NMOS only
impacts the precharge time, which is limited in general due to the parallel precharging of
all gates. The only disadvantage of using a large beta ratio is a reduction in noise margin.
A designer should therefor simultaneously consider the reduced noise margin and performance during the device sizing.
Numerous variations of Domino
VDD
logic have been proposed [Bernstein98].
Mp
CLK
One optimization that reduces area is MulO1= A B(C+D)
tiple Output Domino Logic. The basic
concept is illustrated is Figure 6.69. It
CLK
A
exploits the fact that certain outputs are
O2= B(C+D) = B O3
CLK
subsets of other outputs to generate a
B
number of logical functions in a single
O3= C+D
gate. In this example, O3 = C+D is used in
C
D
all three outputs, and hence it is implemented at the bottom of the pull-down
Me
CLK
network. Since O2 equals B ·O3, it can
reuse the logic for O3. Notice that the
Figure 6.69 Multiple output Domino
internal nodes have to be precharged to
VDD to produce the correct results. Given
that the internal nodes precharge to VDD, the number of devices driving precharge devices
is not reduced. However, the number of evaluation transistors is drastically reduced as
they are amortized over multiple outputs. Additionally, this approach results in a reduction
of the fan-out factor, once again due to the reuse of transistors over multiple functions.
Compound Domino (Figure 6.70) represents another optimization of the generic
Domino gate, once again minimizing the number of transistors. Instead of each dynamic
gate driving a static inverter, it is possible to combine the outputs of multiple dynamic
gates with the aid of a complex static CMOS gate, as shown in Figure 6.70. The outputs of
three dynamic structures, implementing O1 = A B C, O2 = D E F and O3 = G H, are combined using a single complex CMOS static gate that implements O = (o1+o2) o3. The total
logic function realized this way equals O = A B C D E F + GH.
Compound Domino is a useful tool for constructing complex dynamic logic gates.
Large dynamic stacks are replaced using parallel small fan-in structures and complex
CMOS gates. For example, a large fan-in Domino AND can be implemented as parallel
dynamic NAND structures with lower fan-in that are combined using a static NOR gate.
One important consideration in Compound Domino is the problem associated with back-
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
288
Mp
CLK
Mp
Mp CLK
CLK
O2
O1
O3
A
D
B
E
G
C
F
H
CLK
Me
Chapter 6
Me
CLK
O
Figure 6.70 Compound Domino logic uses
complex static gates at the output of the
dynamic gates.
Me
CLK
gate coupling. Care must be taken to ensure that the dynamic nodes are not affected by the
coupling between the output of the static gates and the output of dynamic nodes.
np-CMOS
The Domino logic presented in the previous section has the disadvantage that each
dynamic gate requires an extra static inverter in the critical path to make the circuit functional. np-CMOS, provides an alternate approach to cascading dynamic logic by using two
flavors (n-tree and p-tree) of dynamic logic. In a p-tree logic gate, PMOS devices are used
to build a pull-up logic network, including a PMOS evaluation transistor (Figure 6.71)
([Goncalvez83, Friedman84, Lee86]). The NMOS predischarge transistor drives the output low during precharge. The output conditionally makes a 0 → 1 transition during evaluation depending on its inputs.
VDD
CLK
VDD
Mp
Out1
In1
In2
In3
PDN
CLK
Me
PUN
In4
Out2
CLK
Me
CLK
To other
N-blocks
Mp
Figure 6.71 The np-CMOS logic
circuit style.
To other
P-blocks
np-CMOS logic exploits the duality between n-tree and p-tree logic gates to eliminate the cascading problem. If the n-tree gates are controlled by CLK, and p-tree gates are
controlled using CLK, n-tree gates can directly drive p-tree gates, and vice-versa. Similar
to Domino, n-tree outputs must go through an inverter when connecting to another n-tree
gate. During the precharge phase (CLK = 0), the output of the n-tree gate, Out1, is charged
Section 6.4
Perspectives
289
to VDD, while the output of the p-tree gate, Out2, is pre-discharged to 0V. Since the n-tree
gate connects PMOS pull-up devices, the PUN of the p-tree is turned off at that time. During evaluation, the output of the n-tree gate can only make a 1→0 transition, conditionally
turning on some transistors in the p-tree. This ensures that no accidental discharge of Out2
can occur. Similarly, n-tree blocks can follow p-tree gates without any problems, as the
inputs to the n-gate are precharged to 0. A disadvantage of the np-CMOS logic style is that
the p-tree blocks are slower than the n-tree modules, due to the lower current drive of the
PMOS transistors in the logic network. Equalizing the propagation delays requires extra
area.
6.4
Perspectives
6.4.1
How to Choose a Logic Style?
In the preceding sections, we have discussed several gate-implementation approaches
using the CMOS technology. Each of the circuit styles has its advantages and disadvantages. Which one to select depends upon the primary requirement: ease of design, robustness, area, speed, or power dissipation. No single style optimizes all these measures at the
same time. Even more, the approach of choice may vary from logic function to logic
function.
The static approach has the advantage of being robust in the presence of noise. This
makes the design process rather trouble-free and amenable to a high degree of automation.
This ease-of-design does not come for free: for complex gates with a large fan-in, complementary CMOS becomes expensive in terms of area and performance. Alternative static
logic styles have therefore been devised. Pseudo-NMOS is simple and fast at the expense
of a reduced noise margin and static power dissipation. Pass-transistor logic is attractive
for the implementation of a number of specific circuits, such as multiplexers and XORdominated logic such as adders.
Dynamic logic, on the other hand, makes it possible to implement fast and small
complex gates. This comes at a price. Parasitic effects such as charge sharing make the
design process a precarious job. Charge leakage forces a periodic refresh, which puts a
lower bound on the operating frequency of the circuit.
The current trend is towards an increased use of complementary static CMOS. This
tendency is inspired by the increased use of design-automation tools at the logic design
level. These tools emphasize optimization at the logic rather than the circuit level and put
a premium on robustness. Another argument is that static CMOS is more amenable to
voltage scaling than some of the other approaches discussed in this chapter.
6.4.2
Designing Logic for Reduced Supply Voltages
In Chapter 3, we projected that the supply voltage for CMOS processes will continue to
drop over the coming decade, and may go as low as 0.6V by 2010. To maintain performance under those conditions, it is essential that the device thresholds scale as well. Fig-
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
290
Chapter 6
ure 6.72a shows a plot of the (VT, VDD) ratio required to maintain a given performance
level (assuming that other device characteristics remain identical).
This trade-off is not without penalty. Reducing the threshold voltage, increases the
subthreshold leakage current exponentially as we derived in Eq. (3.40) (repeated here for
the sake of clarity).
1.5
1.25
VDD,V
0.75
tpd=645pS
ID, A
tpd=420pS
1.0
tpd=840pS
0.5
0.25
0.0
0.05
0.15
0.25
0.35
VT, V
(a) VDD/VT for fixed performance
10-2
10-3
VT = 0.1V
10-4
10-5
VT = 0.4 V
10-6
-7
10
10-8
10-9
10-10
10-11
10-12
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
VGS, V
(b) Leakage as a function of VT
0.45
Figure 6.72 Voltage Scaling (VDD/VT on delay and leakage)
Ileakage = I S 10
V GS – V Th
-----------------------
S
1 – 10
nV D S
– -----------S
(6.40)
with S the slope factor of the device. The subthreshold leakage of an inverter is the current
of the NMOS for Vin = 0V and Vout = VDD (or the PMOS current for Vin = VDD and Vout =
0). The exponential increase in inverter leakage for decreasing thresholds illustrated in
Figure 6.72b.
These leakage currents are particularly a concern for designs that feature intermittent computational activity separated by long periods of inactivity. For example, the processor in a cellular phone remains in idle mode for a majority of the time. While the
processor is shutdown mode, the system should ideally consume zero or near-zero power.
This is only possible if leakage is low—this is, the devices have a high threshold voltage.
This is in contradictory to the scaling scenario that we just depicted, where high performance under low supply voltage means reduced thresholds. To satisfy the contradicting
requirements of high-performance during active periods, and low leakage during standby,
several process modifications or leakage-control techniques have been introduced in
CMOS processes. Most processes with feature sizes at and below 0.18 µm CMOS support
devices with different thresholds—typically a device with low threshold for high performance circuits, and a transistor with high threshold for leakage control. Another approach
that is gaining ground is the dynamic control of the threshold voltage of a device by
exploiting the body effect of the transistor. To use this approach for the control of individual devices requires a dual-well process (see Figure 2.2).
Clever circuit design can also help to reduce the leakage current, which is a function
of the circuit topology and the value of the inputs applied to the gate. Since VT depends on
body bias (VBS), the sub-threshold leakage of an MOS transistor depends not only on the
gate drive (VGS), but also on the body bias. In an inverter with In = 0, the sub-threshold
Section 6.4
Perspectives
291
leakage of the inverter is set by the NMOS transistor with its VGS = VBS = 0 V. In more
complex CMOS gates, the leakage current depends upon the input vector. For example,
the sub-threshold leakage current of a two-input NAND gate is the least when A = B = 0.
Under these conditions, the intermediate node X settles to,
V X ≈ V th ln ( 1 + n )
(6.41)
The NAND gate sub-threshold leakage is then set by the top-most NMOS transistor with
VGS = VBS = -VX. Clearly, the sub-threshold leakage under this condition is slightly smaller
than that of the inverter. This reduction in sub-threshold leakage due to stacked transistors
is called the stack effect. Figure 6.73 shows the leakage components for a simple twoinput NAND gate.
VDD
A
P1
B
P2
G
A
B
VX
ISUB
0
0
1
1
0
1
0
1
Vth ln (1+n)
0
Vdd-VT
0
INSUB (VGS = VBS = -VX)
INSUB (VGS = VBS = 0)
INSUB (VGS = VBS = 0)
2 IPSUB (VSG = VSB = 0)
N1
VX
B
A
N2
Figure 6.73 Sub-threshold leakage reduction due to stack effect
in a two-input NAND gate.
In short-channel MOS transistors, the sub-threshold leakage current depends not
only on the gate drive (VGS) and the body bias (VBS), but also depends on the drain voltage
(VDS). The threshold voltage of a short-channel MOS transistor decreases with increasing
VDS due to drain induced barrier lowering (DIBL). Typical value for DIBL can range
from 20-150 mV change in VT per volt change in VDS. Figure 6.74 illustrates the impact on
the sub-threshold leakage as a result of
• a decrease in gate drive—point A to B
• an increase in body bias—point A to C
• an increase in drain voltage—point A to D.
Because of the latter, the impact of the stack effect is even more significant for
short-channel transistors. The intermediate voltage reduces the drain-source voltage of the
top-most device, and hence reduces its leakage. Consider again the two-input NAND gate
of Figure 6.73, when both M1and M2 are off. From the simulated load lines shown in Figure 6.75, we see that VX settles to approximately 100 mV in steady state. The steady state
sub-threshold leakage in the NAND gate is hence due to VGS = VBS = -100 mV and VDS =
VDD - 100 mV, which is 20 times smaller than that leakage of a stand-alone NMOS transistor with VGS = VBS = 0 mV and VDS = VDD [Ye98].
In summary, the sub-threshold leakage in complex stacked circuits can be significantly lower than in individual devices. Observe that the maximum leakage reduction
occurs when all the transistors in the stack are off, and the intermediate node voltage
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
292
Chapter 6
Figure 6.74 Dependence of subthreshold leakage current on terminal
voltages for a typical 0.25 µm NMOS
Figure 6.75 Load line indicating the
steady state solution for the intermediate
node voltage in a transistor stack.
reaches its steady state value. Exploiting this effect requires a careful selection of the input
signals to every gate during standby or sleep mode.
Problem 6.8 Computing VX
Eq. (6.41) represents intermediate node voltage for a two-input NAND with less than 10%
error, when A = B = 0. Derive Eq. (6.41) assuming (i) VT and Io of M1 and M2 are approximately equal, (ii) NMOS transistors are identically sized, and (iii) n < 1.5. Explain the temperature dependence of stack effect and leakage reduction due to stack effect using equation
(4.5).
6.5
Summary
In this chapter, we have extensively analyzed the behavior and performance of combinational CMOS digital circuits with regard to area, speed, and power.
Section 6.6
To Probe Further
293
• Static complementary CMOS combines dual pull-down and pull-up networks, only
one of which is enabled at any time.
• The performance of a CMOS gate is a strong function of the fan-in. Techniques to
deal with fan-in include transistor sizing, input reordering, and partitioning. The
speed is also a linear function of the fan-out. Extra buffering is needed for large fanouts.
• The ratioed logic style consists of an active pull-down (up) network connected to a
load device. This results in a substantial reduction in gate complexity at the expense
of static power consumption and an asymmetrical response. Careful transistor sizing
is necessary to maintain sufficient noise margins. The most popular approaches in
this class are the pseudo-NMOS techniques and differential DCVSL, which requires
complementary signals.
• Pass-transistor logic implements a logic gate as a simple switch network. This
results in very simple implementations for some logic functions. Long cascades of
switches are to be avoided due to a quadratic increase in delay with respect to the
number of elements in the chain. NMOS-only pass-transistor logic produces even
simpler structures, but might suffer from static power consumption and reduced
noise margins. This problem can be addressed by adding a level-restoring transistor.
• The operation of dynamic logic is based on the storage of charge on a capacitive
node and the conditional discharging of that node as a function of the inputs. This
calls for a two-phase scheme, consisting of a precharge followed by an evaluation
step. Dynamic logic trades off noise margin for performance. It is sensitive to parasitic effects such as leakage, charge redistribution, and clock feedthrough. Cascading dynamic gates can cause problems, and should be addressed carefully.
• The power consumption of a logic network is strongly related to the switching activity of the network. This activity is a function of the input statistics, the network
topology, and the logic style. Sources of power consumption such as glitches and
short-circuit currents can be minimized by careful circuit design and transistor sizing.
• Threshold voltage scaling is required for low-voltage operation. Leakage control is
critical for low-voltage operation
6.6
To Probe Further
The topic of (C)MOS logic styles is treated extensively in the literature. Numerous texts
have been devoted to the issue. Some of the most comprehensive treatments can be found
in [Weste93] and [Chandrakasan01]. Regarding the intricacies of high-performance
design, [Shoji96] and [Bernstein98] offer the most in-depth discussion of the optimization
and analysis of digital MOS circuits. The topic of power minimization is relatively new.
Excellent reference works are [Chandrakasan95] and [Rabaey95].
294
DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
Chapter 6
Innovations in the MOS logic area are typically published in the proceedings of the
ISSCC Conference and the VLSI circuits symposium, as well as the IEEE Journal of Solid
State Circuits (especially the November issue).
REFERENCES
[Bernstein98] K. Bernstein et al., High-Speed CMOS Design Styles, Kluwer Academic Publishers,
1998.
[Chandrakasan95] A. Chandrakasan and R. Brodersen, Low Power Digital CMOS Design, Kluwer
Academic Publishers, 1995.
[Chandrakasan01] A. Chandrakasan, W. Bowhill, and F. Fox, ed., Design of High-Performance
Microprocessor Circuits, IEEE Press, 2001.
[Friedman84] V. Friedman and S. Liu, “Dynamic Logic CMOS Circuits,” IEEE Journal of Solid
State Circuits, vol. SC-19, no. 2, pp. 263–266, April 1984.
[Goncalvez83] N. Goncalvez and H. De Man, “NORA: A Racefree Dynamic CMOS Technique for
Pipelined Logic Structures,” IEEE Journal of Solid State Circuits, vol. SC-18, no. 3, pp.
261–266, June 1983.
[Heller84] L. Heller et al., “Cascade Voltage Switch Logic: A Differential CMOS Logic Family,”
Proc. IEEE ISSCC Conference, pp. 16–17, February 1984.
[Krambeck82] R. Krambeck et al., “High-Speed Compact Circuits with CMOS,” IEEE Journal of
Solid State Circuits, vol. SC-17, no. 3, pp. 614–619, June 1982.
[Lee86] C. M. Lee and E. Szeto, “Zipper CMOS,” IEEE Circuits and Systems Magazine, pp. 10–16,
May 1986.
[Parameswar96] A.Parameswar, H.Hara, and T.Sakurai, “A swing restored pass-transistor logicbased multiply and accumulate circuit for multimedia applications,” IEEE Journal of Solid State
Circuits, vol.SC-31, no.6, pp.805-809, June 1996.
[Rabaey95] J. Rabaey and M. Pedram, Ed., Low Power Design Methodologies, Kluwer, 1995.
[Radhakrishnan85] D. Radhakrishnan, S. Whittaker, and G. Maki, “Formal Design Procedures for
Pass-Transistor Switching Circuits,” IEEE Journal of Solid State Circuits, vol. SC-20, no. 2,
pp. 531–536, April 1985.
[Shoji88] M. Shoji, CMOS Digital Circuit Technology, Prentice Hall, 1988.
[Shoji96] M. Shoji, High-Speed Digital Circuits, Addison-Wesley, 1996.
[Sutherland99] I. Sutherland, B. Sproull, and D. Harris, Logical Effort, Morgan Kaufmann, 1999.
[Weste93] N. Weste and K. Eshragian, Principles of CMOS VLSI Design: A Systems Perspective,
Addison-Wesley, 1993.
[Yano90] K. Yano et al., “A 3.8 ns CMOS 16 × 16 b Multiplier Using Complimentary PassTransistor Logic,” IEEE Journal of Solid State Circuits, vol. SC-25, no 2, pp. 388–395, April
1990.
[Ye98] Y. Ye, S. Borkar, and V. De, “A new technique for standby leakage reduction in high-performance circuits,” Symposium on VLSI Circuits, pp 40-41, 1998.
Section 6.6
To Probe Further
295
chapter7.fm Page 296 Friday, January 18, 2002 9:09 AM
CHAPTER
7
DESIGNING SEQUENTIAL LOGIC
CIRCUITS
Implementation techniques for flip-flops, latches, oscillators, pulse generators,
and Schmitt triggers
n
Static versus dynamic realization
n
Choosing clocking strategies
7.1
7.2
7.3
Introduction
Alternative Register Styles
Timing Metrics for Sequential Circuits
7.4.1
Pulse Registers
7.1.2
Classification of Memory Elements
7.4.2
Sense-Amplifier Based Registers
Static Latches and Registers
7.5 Pipelining: An approach to optimize sequential
circuits
7.2.1
The Bistability Principle
7.2.2
SR Flip-Flops
7.5.1
Latch- vs. Register-Based Pipelines
7.2.3
Multiplexer-Based Latches
7.5.2
7.2.4
Master-Slave Edge-Triggered Register
NORA-CMOS—A Logic Style for Pipelined
Structures
7.2.5
Low-Voltage Static Latches
7.6
Dynamic Latches and Registers
7.3.1
296
7.4
7.1.1
Dynamic Transmission-Gate Edge-triggered
Registers
Non-Bistable Sequential Circuits
7.6.1
The Schmitt Trigger
7.6.2
Monostable Sequential Circuits
7.6.3
Astable Circuits
7.3.2
C2MOS—A Clock-Skew Insensitive
Approach
7.7
Perspective: Choosing a Clocking Strategy
7.3.3
True Single-Phase Clocked Register
(TSPCR)
7.8
Summary
7.9
To Probe Further
chapter7.fm Page 297 Friday, January 18, 2002 9:09 AM
Section 7.1
7.1
Introduction
297
Introduction
Combinational logic circuits, described earlier, have the property that the output of a logic
block is only a function of the current input values, assuming that enough time has elapsed
for the logic gates to settle. Yet virtually all useful systems require storage of state information, leading to another class of circuits called sequential logic circuits. In these circuits, the output not only depends upon the current values of the inputs, but also upon
preceding input values. In other words, a sequential circuit remembers some of the past
history of the system—it has memory.
Figure 7.1 shows a block diagram of a generic finite state machine (FSM) that consists of combinational logic and registers, which hold the system state. The system
depicted here belongs to the class of synchronous sequential systems, in which all registers are under control of a single global clock. The outputs of the FSM are a function of the
current Inputs and the Current State. The Next State is determined based on the Current
State and the current Inputs and is fed to the inputs of registers. On the rising edge of the
clock, the Next State bits are copied to the outputs of the registers (after some propagation
delay), and a new cycle begins. The register then ignores changes in the input signals until
the next rising edge. In general, registers can be positive edge-triggered (where the input
data is copied on the positive edge of the clock) or negative edge-triggered (where the
input data is copied on the negative edge, as is indicated by a small circle at the clock
input).
Inputs
Outputs
COMBINATIONAL
LOGIC
Current State
Registers
Q
Next State
D
CLK
Figure 7.1
Block diagram of a finite state machine using positive edge-triggered registers.
This chapter discusses the CMOS implementation of the most important sequential
building blocks. A variety of choices in sequential primitives and clocking methodologies
exist; making the correct selection is getting increasingly important in modern digital circuits, and can have a great impact on performance, power, and/or design complexity.
Before embarking on a detailed discussion on the various design options, a revision of the
design metrics, and a classification of the sequential elements is necessary.
7.1.1
Timing Metrics for Sequential Circuits
There are three important timing parameters associated with a register as illustrated in Figure 7.2. The set-up time (tsu) is the time that the data inputs (D input) must be valid before
the clock transition (this is, the 0 to 1 transition for a positive edge-triggered register). The
hold time (thold) is the time the data input must remain valid after the clock edge. Assum-
chapter7.fm Page 298 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
298
CLK
t
tsu
D
Chapter 7
Register
D
thold
DATA
STABLE
Q
CLK
t
tc-q
Q
DATA
STABLE
Figure 7.2 Definition of set-up
time, hold time, and propagation
t delay of a synchronous register.
ing that the set-up and hold-times are met, the data at the D input is copied to the Q output
after a worst-case propagation delay (with reference to the clock edge) denoted by tc-q.
Given the timing information for the registers and the combination logic, some system-level timing constraints can be derived. Assume that the worst-case propagation
delay of the logic equals tplogic, while its minimum delay (also called the contamination
delay) is tcd. The minimum clock period T, required for proper operation of the sequential
circuit is given by
T ≥ t c-q + t p log ic + t su
(7.1)
The hold time of the register imposes an extra constraint for proper operation,
t cdregister + t cdlogic ≥ t hold
(7.2)
where tcdregister is the minimum propagation delay (or contamination delay) of the register.
As seen from Eq. (7.1), it is important to minimize the values of the timing parameters associated with the register, as these directly affect the rate at which a sequential circuit can be clocked. In fact, modern high-performance systems are characterized by a
very-low logic depth, and the register propagation delay and set-up times account for a
significant portion of the clock period. For example, the DEC Alpha EV6 microprocessor
[Gieseke97] has a maximum logic depth of 12 gates, and the register overhead stands for
approximately 15% of the clock period. In general, the requirement of Eq. (7.2) is not hard
to meet, although it becomes an issue when there is little or no logic between registers.1
7.1.2
Classification of Memory Elements
Foreground versus Background Memory
At a high level, memory is classified into background and foreground memory. Memory
that is embedded into logic is foreground memory, and is most often organized as individual registers of register banks. Large amounts of centralized memory core are referred to
as background memory. Background memory, discussed later in this book, achieves
1
(or when the clocks at different registers are somewhat out of phase due to clock
skew, as will be discussed in a later Chapter)
chapter7.fm Page 299 Friday, January 18, 2002 9:09 AM
Section 7.1
Introduction
299
higher area densities through efficient use of array structures and by trading off performance and robustness for size. In this chapter, we focus on foreground memories.
Static versus Dynamic Memory
Memories can be static or dynamic. Static memories preserve the state as long as the
power is turned on. Static memories are built using positive feedback or regeneration,
where the circuit topology consists of intentional connections between the output and the
input of a combinational circuit. Static memories are most useful when the register won’t
be updated for extended periods of time. An example of such is configuration data, loaded
at power-up time. This condition also holds for most processors that use conditional clocking (i.e., gated clocks) where the clock is turned off for unused modules. In that case, there
are no guarantees on how frequently the registers will be clocked, and static memories are
needed to preserve the state information. Memory based on positive feedback fall under
the class of elements called multivibrator circuits. The bistable element, is its most popular representative, but other elements such as monostable and astable circuits are also frequently used.
Dynamic memories store state for a short period of time—on the order of milliseconds. They are based on the principle of temporary charge storage on parasitic capacitors
associated with MOS devices. As with dynamic logic discussed earlier, the capacitors
have to be refreshed periodically to annihilate charge leakage. Dynamic memories tend to
simpler, resulting in significantly higher performance and lower power dissipation. They
are most useful in datapath circuits that require high performance levels and are periodically clocked. It is possible to use dynamic circuitry even when circuits are conditionally
clocked, if the state can be discarded when a module goes into idle mode.
Latches versus Registers
A latch is an essential component in the construction of an edge-triggered register. It is
level-sensitive circuit that passes the D input to the Q output when the clock signal is high.
This latch is said to be in transparent mode. When the clock is low, the input data sampled
on the falling edge of the clock is held stable at the output for the entire phase, and the
latch is in hold mode. The inputs must be stable for a short period around the falling edge
of the clock to meet set-up and hold requirements. A latch operating under the above conditions is a positive latch. Similarly, a negative latch passes the D input to the Q output
when the clock signal is low. The signal waveforms for a positive and negative latch are
shown in Figure 7.3. A wide variety of static and dynamic implementations exists for the
realization of latches.
Contrary to level-sensitive latches, edge-triggered registers only sample the input on
a clock transition — 0-to-1 for a positive edge-triggered register, and 1-to-0 for a negative
edge-triggered register. They are typically built using the latch primitives of Figure 7.3. A
most-often recurring configuration is the master-slave structure that cascades a positive
and negative latch. Registers can also be constructed using one-shot generators of the
clock signal (“glitch” registers), or using other specialized structures. Examples of these
are shown later in this chapter.
chapter7.fm Page 300 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
300
Positive Latch
D
In
Q
Chapter 7
Negative Latch
Out
D
In
G
Q
Out
G
CLK
CLK
clk
clk
In
In
Out
Out
Out
stable
Out
follows In
Out
stable
Out
follows In
Figure 7.3 Timing of positive and negative latches.
Static Latches and Registers
7.2.1
The Bistability Principle
Static memories use positive feedback to create a bistable circuit — a circuit having two
stable states that represent 0 and 1. The basic idea is shown in Figure 7.4a, which shows
two inverters connected in cascade along with a voltage-transfer characteristic typical of
such a circuit. Also plotted are the VTCs of the first inverter, that is, Vo1 versus Vi1, and the
second inverter (Vo2 versus Vo1). The latter plot is rotated to accentuate that Vi2 = Vo1.
Assume now that the output of the second inverter Vo2 is connected to the input of the first
Vi1, as shown by the dotted lines in Figure 7.4a. The resulting circuit has only three possible operation points (A, B, and C), as demonstrated on the combined VTC. The following
important conjecture is easily proven to be valid:
Vi1
Vo1 = Vi2
Vi2 = Vo1
Vo1
Vo2
Vi1
Vo2 = Vi1
(a)
Figure 7.4 Two cascaded inverters (a)
and their VTCs (b).
Vi2 = Vo1
7.2
Vo2
A
C
B
Vi1 = Vo2
(b)
chapter7.fm Page 301 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
301
Under the condition that the gain of the inverter in the transient region is larger than 1, only A
and B are stable operation points, and C is a metastable operation point.
Suppose that the cross-coupled inverter pair is biased at point C. A small deviation from
this bias point, possibly caused by noise, is amplified and regenerated around the circuit
loop. This is a consequence of the gain around the loop being larger than 1. The effect is
demonstrated in Figure 7.5a. A small deviation δ is applied to Vi1 (biased in C). This deviation is amplified by the gain of the inverter. The enlarged divergence is applied to the
second inverter and amplified once more. The bias point moves away from C until one of
the operation points A or B is reached. In conclusion, C is an unstable operation point.
Every deviation (even the smallest one) causes the operation point to run away from its
original bias. The chance is indeed very small that the cross-coupled inverter pair is biased
at C and stays there. Operation points with this property are termed metastable.
A
Figure 7.5
Metastability.
Vi2 = Vo1
Vi2 = Vo1
A
C
C
B
δ
(a)
Vi1 = Vo2
B
δ
Vi1 = Vo2
(b)
On the other hand, A and B are stable operation points, as demonstrated in Figure
7.5b. In these points, the loop gain is much smaller than unity. Even a rather large deviation from the operation point is reduced in size and disappears.
Hence the cross-coupling of two inverters results in a bistable circuit, that is, a circuit with two stable states, each corresponding to a logic state. The circuit serves as a
memory, storing either a 1 or a 0 (corresponding to positions A and B).
In order to change the stored value, we must be able to bring the circuit from state A
to B and vice-versa. Since the precondition for stability is that the loop gain G is smaller
than unity, we can achieve this by making A (or B) temporarily unstable by increasing G to
a value larger than 1. This is generally done by applying a trigger pulse at Vi1 or Vi2. For
instance, assume that the system is in position A (Vi1 = 0, Vi2 = 1). Forcing Vi1 to 1 causes
both inverters to be on simultaneously for a short time and the loop gain G to be larger
than 1. The positive feedback regenerates the effect of the trigger pulse, and the circuit
moves to the other state (B in this case). The width of the trigger pulse need be only a little
larger than the total propagation delay around the circuit loop, which is twice the average
propagation delay of the inverters.
In summary, a bistable circuit has two stable states. In absence of any triggering, the
circuit remains in a single state (assuming that the power supply remains applied to the
circuit), and hence remembers a value. A trigger pulse must be applied to change the state
chapter7.fm Page 302 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
302
Chapter 7
of the circuit. Another common name for a bistable circuit is flip-flop (unfortunately, an
edge-triggered register is also referred to as a flip-flop).
7.2.2
SR Flip-Flops
The cross-coupled inverter pair shown in the previous section provides an approach to
store a binary variable in a stable way. However, extra circuitry must be added to enable
control of the memory states. The simplest incarnation accomplishing this is the wellknow SR —or set-reset— flip-flop, an implementation of which is shown in Figure 7.6a.
This circuit is similar to the cross-coupled inverter pair with NOR gates replacing the
inverters. The second input of the NOR gates is connected to the trigger inputs (S and R),
that make it possible to force the outputs Q and Q to a given state. These outputs are complimentary (except for the SR = 11 state). When both S and R are 0, the flip-flop is in a quiescent state and both outputs retain their value (a NOR gate with one of its input being 0
looks like an inverter, and the structure looks like a cross coupled inverter). If a positive
(or 1) pulse is applied to the S input, the Q output is forced into the 1 state (with Q going to
0). Vice versa, a 1 pulse on R resets the flip-flop and the Q output goes to 0.
S
S
R
Q
Q
0
0
Q
Q
1
0
1
0
0
1
1
1
0
0
1
0
Q
S
Q
R
Q
Q
R
Forbidden State
(a) Schematic diagram
Figure 7.6
(c) Characteristic table
(b) Logic symbol
NOR-based SR flip-flop.
These results are summarized in the characteristic table of the flip-flop, shown in
Figure 7.6c. The characteristic table is the truth table of the gate and lists the output states
as functions of all possible input conditions. When both S and R are high, both Q and Q
are forced to zero. Since this does not correspond with our constraint that Q and Q must be
complementary, this input mode is considered to be forbidden. An additional problem
with this condition is that when the input triggers return to their zero levels, the resulting
state of the latch is unpredictable and depends on whatever input is last to go low. Finally,
Figure 7.6 shows the schematics symbol of the SR flip-flop.
Problem 7.1
SR Flip-Flop Using NAND Gates
An SR flip-flop can also be implemented using a
cross-coupled NAND structure as shown in Figure
7.7. Derive the truth table for a such an implementation.
S
R
Q
Q
Figure 7.7 NAND-based SR flip-flop.
chapter7.fm Page 303 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
303
The SR flip-flops discussed so far are asynchronous, and do not require a clock signal. Most systems operate in a synchronous fashion with transition events referenced to a
clock. One possible realization of a clocked SR flip-flop— a level-sensitive positive
latch— is shown in Figure 7.8. It consists of a cross-coupled inverter pair, plus 4 extra
transistors to drive the flip-flop from one state to another and to provide clocked operation. Observe that the number of transistors is identical to the implementation of Figure
7.6, but the circuit has the added feature of being clocked. The drawback of saving some
transistors over a fully-complimentary CMOS implementation is that transistor sizing
becomes critical in ensuring proper functionality. Consider the case where Q is high and
an R pulse is applied. The combination of transistors M4, M7, and M8 forms a ratioed
inverter. In order to make the latch switch, we must succeed in bringing Q below the
switching threshold of the inverter M1-M2. Once this is achieved, the positive feedback
causes the flip-flop to invert states. This requirement forces us to increase the sizes of transistors M5, M6, M7, and M8.
VDD
M2
M4
Q
Q
CLK
S
M6
M1
M5
M3
M8
CLK
M7
R
Figure 7.8
CMOS clocked SR flip-flop.
The presented flip-flop does not consume any static power. In steady-state, one
inverter resides in the high state, while the other one is low. No static paths between VDD
and GND can exist except during switching.
Example 7.1
Transistor Sizing of Clocked SR Latch
Assume that the cross-coupled inverter pair is designed such that the inverter threshold VM is
located at VDD/2. For a 0.25 µm CMOS technology, the following transistor sizes were
selected: (W/L)M1 = (W/L)M3 = (0.5µm/0.25µm), and (W/L)M2 = (W/L)M4 = (1.5µm/0.25µm).
Assuming Q = 0, we determine the minimum sizes of M5, M6, M7, and M8 to make the device
switchable.
To switch the latch from the Q = 0 to the Q = 1 state, it is essential that the low level of
the ratioed, pseudo-NMOS inverter (M5-M6)-M2 be below the switching threshold of the
inverter M3-M4 that equals VDD/2. It is reasonable to assume that as long as VQ > VM, VQ
equals 0, and the gate of transistor M2 is grounded. The boundary conditions on the transistor
sizes can be derived by equating the currents in the inverter for VQ = VDD / 2, as given in Eq.
(7.3) (this ignores channel length modulation). The currents are determined by the saturation
current since VSET = VDD = 2.5V and VM = 1.25V. We assume that M5 and M6 have identical
sizes and that W/L5-6 is the effective ratio of the series-connected devices. Under this condi-
chapter7.fm Page 304 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
304
Chapter 7
tion, the pull-down network can be modeled by a single transistor M56, whose length is twice
the length of the individual devices.
2
2
V DSATp
V DSATn
W
W
( V – V )V
k′ n -----
Tn
DSATn – ----------------- = k′ p ----- ( – V DD – V Tp )V DSATp – -----------------
L 2
2
L 5 – 6 DD
2
(7.3)
Using the parameters for the 0.25 µm process, Eq. (7.3) results in the constraint that the
effective (W/L)M5-6 ≥ 2.26. This implies that the individual device ratio for M5 or M6 must be
larger that approximately 4.5. Figure 7.9a shows the DC plot of VQ as a function of the individual device sizes of M5 and M6. We notice that the individual device ratio of greater than 3
is sufficient to bring the Q voltage to the inverter switching threshold. The difference between
the manual analysis and simulation arises due to second order effects such as DIBL and channel length modulation. Figure 7.9b, which shows the transient response for different device
sizes. The plot confirms that an individual W/L ratio of greater than 3 is required to overpower
the feedback and switch the state of the latch.
2.0
3
Q
S
1.5
W=0.5µm
W=0.6µm
W=0.7µm
Volts
Q (Volts)
2
1.0
1
W=0.8µm
0.5
0.02.0
2.5
3.0
W/L5and 6
(a)
3.5
4.0
W=0.9µm
W=1µm
0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
time (nsec)
(b)
Figure 7.9 Sizing issues for SR flip-flop. (a) DC output voltage vs. individual pulldown
device size of M5 and M6 with W/L2= 1.5µm/.25µm. (b) Transient response shows that M5
and M6 must each have a W/L larger than 3 to switch the SR flip-flop.
The positive feedback effect makes a manual derivation of propagation delay of the
SR latch quite hard. Some simplifications are therefore necessary. Consider, for instance,
the latch of Figure 7.8, where Q and Q are set to 0 and 1, respectively. A pulse is applied at
node S, causing the latch to toggle. In the first phase of the transient, node Q is being
pulled down by transistors M5 and M6. Since node Q is initially low, the PMOS device M2
is on while M1 is off. The transient response is hence determined by the pseudo-NMOS
inverter formed by (M5-M6) and M2. Once Q reaches the switching threshold of the CMOS
inverter M3-M4, this inverter reacts and the positive feedback comes into action, turning
M2 off and M1 on. This accelerates the pulling down of node Q. From this analysis, we can
derive that the propagation delay of node Q is approximately equal to the delay of the
pseudo-NMOS inverter formed by (M5-M6) and M2. To obtain the delay for node Q, it is
sufficient to add the delay of the complementary CMOS inverter M3-M4.
Example 7.2
Propagation Delay of Static SR Flip-Flop
The transient response of the latch in Figure 7.8, as obtained from simulation, is plotted in
Figure 7.10. The devices are sized as described in Example 7.1, and a load of a single inverter
chapter7.fm Page 305 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
305
is assumed for each latch output. The flip-flop is initially in the reset state, and an S-pulse is
applied. As we can observe, this results first in a discharging of the Q output while Q stays at
0. Once the switching threshold of the inverter M3-M4 is reached, the Q output starts to rise.
The delay of this transient is solely determined by the M3-M4 inverter, which is hampered by
the slow rise time at its input. From the simulation results, we can derive that tpQ and tpQ equal
120psec and 230psec, respectively.
3.0
2.0
Q
Volts
SET
tpQ
1.0
Q
tpQ
Figure 7.10 Transient response
of SR flip-flop.
0.0
0.9
Problem 7.2
1.0
1.1
1.2
1.3
Time (nsec)
1.4
1.5
Complimentary CMOS SR FF
Instead of using the modified SR FF of Figure 7.8, it is also possible to use complementary
logic to implement the clocked SR FF. Derive the transistor schematic (which consists of 12
transistors). This circuit is more complex, but switches faster and consumes less switching
power. Explain why.
7.2.3
Multiplexer-Based Latches
There are many approaches for constructing latches. One very common technique
involves the use of transmission gate multiplexers. Multiplexer based latches can provide
similar functionality to the SR latch, but has the important added advantage that the sizing
of devices only affects performance and is not critical to the functionality.
Figure 7.11 shows an implementation of static positive and negative latches based
on multiplexers. For a negative latch, when the clock signal is low, the input 0 of the multiplexer is selected, and the D input is passed to the output. When the clock signal is high,
the input 1 of the multiplexer, which connects to the output of the latch, is selected. The
feedback holds the output stable while the clock signal is high. Similarly in the positive
latch, the D input is selected when clock is high, and the output is held (using feedback)
when clock is low.
A transistor level implementation of a positive latch based on multiplexers is shown
in Figure 7.12. When CLK is high, the bottom transmission gate is on and the latch is
chapter7.fm Page 306 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
306
Negative Latch
1
0
D
Chapter 7
Positive Latch
0
Q
Q
1
D
Figure 7.11 Negative and positive
latches based on multiplexers.
CLK
CLK
transparent - that is, the D input is copied to the Q output. During this phase, the feedback
loop is open since the top transmission gate is off. Unlike the SR FF, the feedback does not
have to be overridden to write the memory and hence sizing of transistors is not critical for
realizing correct functionality. The number of transistors that the clock touches is important since it has an activity factor of 1. This particular latch implementation is not particularly efficient from this metric as it presents a load of 4 transistors to the CLK signal.
CLK
Q
CLK
D
Figure 7.12 Positive latch built using
transmission gates.
CLK
It is possible to reduce the clock load to two transistors by using implement multiplexers using NMOS only pass transistor as shown in Figure 7.13. The advantage of this
approach is the reduced clock load of only two NMOS devices. When CLK is high, the
latch samples the D input, while a low clock-signal enables the feedback-loop, and puts
the latch in the hold mode. While attractive for its simplicity, the use of NMOS only pass
transistors results in the passing of a degraded high voltage of VDD-VTn to the input of the
first inverter. This impacts both noise margin and the switching performance, especially in
the case of low values of VDD and high values of VTn. It also causes static power dissipation in first inverter, as already pointed out in Chapter 6. Since the maximum input-voltage to the inverter equals VDD-VTn, the PMOS device of the inverter is never turned off,
resulting is a static current flow.
7.2.4
Master-Slave Edge-Triggered Register
The most common approach for constructing an edge-triggered register is to use a masterslave configuration, as shown in Figure 7.14. The register consists of cascading a negative
latch (master stage) with a positive latch (slave stage). A multiplexer-based latch is used in
this particular implementation, although any latch could be used. On the low phase of the
clock, the master stage is transparent, and the D input is passed to the master stage output,
chapter7.fm Page 307 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
307
QM
CLK
D
CLK
QM
CLK
CLK
(a) Schematic diagram
(b) Non-overlapping clocks
Figure 7.13 Multiplexer-based NMOS latch using NMOS-only pass transistors.
QM. During this period, the slave stage is in the hold mode, keeping its previous value
using feedback. On the rising edge of the clock, the master slave stops sampling the input,
and the slave stage starts sampling. During the high phase of the clock, the slave stage
samples the output of the master stage (QM), while the master stage remains in a hold
mode. Since QM is constant during the high phase of the clock, the output Q makes only
one transition per cycle. The value of Q is the value of D right before the rising edge of the
clock, achieving the positive edge-triggered effect. A negative edge-triggered register can
be constructed using the same principle by simply switching the order of the positive and
negative latch (this is, placing the positive latch first).
Slave
CLK
Master
0
1
D
0
1
Q
D
QM
QM
Q
CLK
CLK
Figure 7.14 Positive edge-triggered register based on a master-slave configuration.
A complete transistor-level implementation of a the master-slave positive edge-triggered register is shown in Figure 7.15. The multiplexer is implemented using transmission
gates as discussed in the previous section. When the clock is low (CLK = 1), T1 is on and
T2 is off, and the D input is sampled onto node QM. During this period, T3 is off and T4 is
on and the cross-coupled inverters (I5, I6) holds the state of the slave latch. When the clock
goes high, the master stage stops sampling the input and goes into a hold mode. T1 is off
and T2 is on, and the cross coupled inverters I3 and I4 holds the state of QM. Also, T3 is on
and T4 is off, and QM is copied to the output Q.
Problem 7.3 Optimization of the Master Slave Register
It is possible to remove the inverters I1 and I2 from Figure 7.3 without loss of functionality. Is
there any advantage in including these inverters in the implementation?
chapter7.fm Page 308 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
308
D
I2
T2
I1
T1
I3
I5
T4
I4
T3
Chapter 7
I6
Q
QM
CLK
Figure 7.15 Master-slave positive edge-triggered register using multiplexers.
Timing Properties of Multiplexer-based Master-Slave Registers
Registers are characterized by three important timing parameters: the set-up time, the hold
time and the propagation delay. It is important to understand the factors that affect these
timing parameters, and develop the intuition to manually estimate them. Assume that the
propagation delay of each inverter is tpd_inv, and the propagation delay of the transmission
gate is tpd_tx. Also assume that the contamination delay is 0 and the inverter delay to derive
CLK from CLK has a delay equal to 0.
The set-up time is the time before the rising edge of the clock that the input data D
must become valid. Another way to ask the question is how long before the rising edge
does the D input have to be stable such that QM samples the value reliably. For the transmission gate multiplexer-based register, the input D has to propagate through I1, T1, I3 and
I2 before the rising edge of the clock. This is to ensure that the node voltages on both terminals of the transmission gate T2 are at the same value. Otherwise, it is possible for the
cross-coupled pair I2 and I3 to settle to an incorrect value. The set-up time is therefore
equal to 3 *tpd_inv + tpd_tx.
The propagation delay is the time for the value of QM to propagate to the output Q.
Note that since we included the delay of I2 in the set-up time, the output of I4 is valid
before the rising edge of clock. Therefore the delay tc-q is simply the delay through T3 and
I6 (tc-q = tpd_tx + tpd_inv).
The hold time represents the time that the input must be held stable after the rising
edge of the clock. In this case, the transmission gate T1 turns off when clock goes high and
therefore any changes in the D-input after clock going high are not seen by the input.
Therefore, the hold time is 0.
Example 7.3 Timing analysis using SPICE.
To obtain the set-up time of the register using SPICE, we progressively skew the input with
respect to the clock edge until the circuit fails. Figure 7.16 shows the set-up time simulation
assuming a skew of 210 psec and 200 psec. For the 210 psec case, the correct value of input D
is sampled (in this case, the Q output remains at the value of VDD). For a skew of 200 psec, an
incorrect value propagates to the output (in this case, the Q output transitions to 0). Node QM
starts to go high while the output of I2 (the input to transmission gate T2) starts to fall. However, the clock is enabled before the two nodes across the transmission gate (T2) settle to the
chapter7.fm Page 309 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
309
same value and therefore, results in an incorrect value written into the master latch.The set-up
time for this register is therefore 210 psec.
3.0
3.0
Q
2.5
2.0
QM
1.5
CLK
D
D
CLK
Q
1.0
1.0
QM
I2-T2
0.5
0.5
0.0
0.0
-0.5
I2-T2
1.5
Volts
Volts
2.0
2.5
-0.5
0
0.2
0.4
0.6
0.8
time (nsec)
(a) Tsetup = 0.21 nsec
1
0
0.2
0.4
0.6
0.8
time (nsec)
(b) Tsetup = 0.20 nsec
1
Figure 7.16 Set-up time simulation.
In a similar fashion, the hold time can be simulated. The D input edge is once again
skewed relative to the clock signal till the circuit stop functioning. For this design, the hold
time is 0 - i.e., the inputs can be changed on the clock edge. Finally, for the propagation
delay, the inputs transition at least one set-up time before the rising edge of the clock and the
delay is measured from the 50% point of the CLK edge to the 50% point of the Q output.
From this simulation (Figure 7.17), tc-q (lh) was 160 psec and tc-q(hl) was 180 psec.
The drawback of the transmission gate register is the high capacitive load presented to the
clock signal. The clock load per register is important, since it directly impacts the power
dissipation of the clock network. Ignoring the overhead required to invert the clock signal
(since the buffer inverter overhead can be amortized over multiple register bits), each register has a clock load of 8 transistors. One approach to reduce the clock load at the cost of
robustness is to make the circuit ratioed. Figure 7.18 shows that the feedback transmission
gate can be eliminated by directly cross coupling the inverters.
The penalty for the reduced clock load is increased design complexity. The transmission gate (T1) and its source driver must overpower the feedback inverter (I2) to switch
the state of the cross-coupled inverter.The sizing requirements for the transmission gates
2.5
CLK
Volts
1.5
D
tc-q(lh)
Figure 7.17 Simulation of propagation delay.
tc-q(hl)
Q
0.5
-0.5 0
0.5
1
1.5
time, nsec
2
2.5
chapter7.fm Page 310 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
310
CLK
CLK
D
Chapter 7
I1
T1
I2
CLK
Q
I3
T2
I4
CLK
Figure 7.18 Reduced load clock load static master-slave register.
can be derived using a similar analysis as performed for the SR flip-flop. The input to the
inverter I1 must be brought below its switching threshold in order to make a transition. If
minimum-sized devices are to be used in the transmission gates, it is essential that the
transistors of inverter I2 should be made even weaker. This can be accomplished by making their channel-lengths larger than minimum. Using minimum or close-to-minimumsize devices in the transmission gates is desirable to reduce the power dissipation in the
latches and the clock distribution network.
Another problem with this scheme is the reverse conduction — this is, the second
stage can affect the state of the first latch. When the slave stage is on (Figure 7.19), it is
possible for the combination of T2 and I4 to influence the data stored in I1-I2 latch. As long
as I4 is a weak device, this is fortunately not a major problem.
0
VDD
D
T1
I1
T2
I2
0
VDD
I3
Q
I4
Figure 7.19 Reverse conduction possible in the transmission gate.
Non-ideal clock signals
So far, we have assumed that CLK is a perfect inversion of CLK, or in other words, that the
delay of the generating inverter is zero. Even if this were possible, this would still not be a
good assumption. Variations can exist in the wires used to route the two clock signals, or
the load capacitances can vary based on data stored in the connecting latches. This effect,
known as clock skew is a major problem, and causes the two clock signals to overlap as is
shown in Figure 7.20b. Clock-overlap can cause two types of failures, as illustrated for the
NMOS-only negative master-slave register of Figure 7.20a.
• When the clock goes high, the slave stage should stop sampling the master stage
output and go into a hold mode. However, since CLK and CLK are both high for a
short period of time (the overlap period), both sampling pass transistors conduct and
there is a direct path from the D input to the Q output. As a result, data at the output
can change on the rising edge of the clock, which is undesired for a negative edgetriggered register. The is know as a race condition in which the value of the output
chapter7.fm Page 311 Friday, January 18, 2002 9:09 AM
Section 7.2
Static Latches and Registers
311
X
CLK
Q
CLK
A
D
B
CLK
CLK
(a) Schematic diagram
CLK
Figure 7.20 Master-slave register based
on NMOS-only pass transistors.
CLK
(b) Overlapping clock pairs
Q is a function of whether the input D arrives at node X before or after the falling
edge of CLK. If node X is sampled in the metastable state, the output will switch to a
value determined by noise in the system.
• The primary advantage of the multiplexer-based register is that the feedback loop is
open during the sampling period, and therefore sizing of devices is not critical to
functionality. However, if there is clock overlap between CLK and CLK, node A can
be driven by both D and B, resulting in an undefined state.
Those problems can be avoided by using two non-overlapping clocks PHI1 and PHI2
instead (Figure 7.21), and by keeping the nonoverlap time tnon_overlap between the clocks
large enough such that no overlap occurs even in the presence of clock-routing delays.
During the nonoverlap time, the FF is in the high-impedance state—the feedback loop is
open, the loop gain is zero, and the input is disconnected. Leakage will destroy the state if
this condition holds for too long a time. Hence the name pseudo-static: the register
employs a combination of static and dynamic storage approaches depending upon the state
of the clock.
Problem 7.4
Generating non-overlapping clocks
Figure 7.22 shows one possible implementation of the clock generation circuitry for generating a two-phase non-overlapping clocks. Assuming that each gate has a unit gate delay, derive
the timing relationship between the input clock and the two output clocks. What is the nonoverlap period? How can this period be increased if needed?
7.2.5
Low-Voltage Static Latches
The scaling of supply voltages is critical for low power operation. Unfortunately,
certain latch structures don’t function at reduced supply voltages. For example, without
the scaling of device thresholds, NMOS only pass transistors (e.g., Figure 7.21) don’t
chapter7.fm Page 312 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
312
Chapter 7
Q
PHI2
PHI1
D
PHI2
(a) Schematic diagram
PHI1
PHI1
PHI2
Figure 7.21 Pseudo-static
two-phase D register.
tnon_overlap
(b) Two-phase non-overlapping clocks
scale well with supply voltage due to its inherent threshold drop. At very low power supply voltages, the input to the inverter cannot be raised above the switching threshold,
resulting in incorrect evaluation. Even with the use of transmission gates, performance
degrades significantly at reduced supply voltages.
Scaling to low supply voltages hence requires the use of reduced threshold devices.
However, this has the negative effect of exponentially increasing the sub-threshold leakage power as discussed in Chapter 6. When the registers are constantly accessed, the leakage energy is typically insignificant compared to the switching power. However, with the
use of conditional clocks, it is possible that registers are idle for extended periods and the
leakage energy expended by registers can be quite significant.
Many solutions are being explored to address the problem of high leakage during
idle periods. One approach for this involves the use of Multiple Threshold devices as
shown in Figure 7.23 [Mutoh95]. Only the negative latch is shown here. The shaded
inverters and transmission gates are implemented in low-threshold devices. The lowthreshold inverters are gated using high threshold devices to eliminate leakage.
During normal mode of operation, the sleep devices are tuned on. When clock is
low, the D input is sampled and propagates to the output. When clock is high, the latch is
in the hold mode. The feedback transmission gate conducts and the cross-coupled feedback is enabled. Note there is an extra inverter, needed for storage of state when the latch
is in the sleep state. During idle mode, the high threshold devices in series with the low
threshold inverter are turned off (the SLEEP signal is high), eliminating leakage. It is
assumed that clock is in the high state when the latch is in the sleep state. The feedback
PHI1
CLK
PHI2
Figure 7.22 Circuitry for generating
a two-phase non-overlapping clock.
chapter7.fm Page 313 Friday, January 18, 2002 9:09 AM
Section 7.3
Dynamic Latches and Registers
313
VDD
VDD
SLEEP
High VT
VDD
CLK
SLEEP
High VT
Q
D
SLEEP
SLEEP
High VT
CLK
High VT
CLK
VDD
Figure 7.23 Solving the leakage
problem using multiple-threshold
CMOS.
low-threshold transmission gate is turned on and the cross-coupled high-threshold devices
maintains the state of the latch.
Problem 7.5 Transistor minimization in the MTCMOS register
Unlike combinational logic, both NMOS and PMOS high-threshold devices are required to
eliminate the leakage in low-threshold latches. Explain why this is the case.
Hint: Eliminate the high-VT NMOS or high-VT PMOS of the low-threshold inverter on the
right of Figure 7.23, and investigate potential leakage paths.
7.3
Dynamic Latches and Registers
Storage in a static sequential circuit relies on the concept that a cross-coupled inverter pair
produces a bistable element and can thus be used to memorize binary values. This
approach has the useful property that a stored value remains valid as long as the supply
voltage is applied to the circuit, hence the name static. The major disadvantage of the
static gate, however, is its complexity. When registers are used in computational structures
that are constantly clocked such as pipelined datapath, the requirement that the memory
should hold state for extended periods of time can be significantly relaxed.
This results in a class of circuits based on temporary storage of charge on parasitic
capacitors. The principle is exactly identical to the one used in dynamic logic — charge
stored on a capacitor can be used to represent a logic signal. The absence of charge
denotes a 0, while its presence stands for a stored 1. No capacitor is ideal, unfortunately,
and some charge leakage is always present. A stored value can hence only be kept for a
limited amount of time, typically in the range of milliseconds. If one wants to preserve
signal integrity, a periodic refresh of its value is necessary. Hence the name dynamic storage. Reading the value of the stored signal from a capacitor without disrupting the charge
requires the availability of a device with a high input impedance.
chapter7.fm Page 314 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
314
7.3.1
Chapter 7
Dynamic Transmission-Gate Edge-triggered Registers
A fully dynamic positive edge-triggered register based on the master-slave concept is
shown in Figure 7.24. When CLK = 0, the input data is sampled on storage node 1, which
has an equivalent capacitance of C1 consisting of the gate capacitance of I1, the junction
capacitance of T1, and the overlap gate capacitance of T1. During this period, the slave
stage is in a hold mode, with node 2 in a high-impedance (floating) state. On the rising
edge of clock, the transmission gate T2 turns on, and the value sampled on node 1 right
before the rising edge propagates to the output Q (note that node 1 is stable during the high
phase of the clock since the first transmission gate is turned off). Node 2 now stores the
inverted version of node 1. This implementation of an edge-triggered register is very efficient as it requires only 8 transistors. The sampling switches can be implemented using
NMOS-only pass transistors, resulting in an even-simpler 6 transistor implementation.
The reduced transistor count is attractive for high-performance and low-power systems.
CLK
D
T1
CLK
1
I1
C1
CLK
T2
CLK
2
I3
Q
C2
Figure 7.24 Dynamic edge-triggered register.
The set-up time of this circuit is simply the delay of the transmission gate, and corresponds to the time it takes node 1 to sample the D input. The hold time is approximately
zero, since the transmission gate is turned off on the clock edge and further inputs changes
are ignored. The propagation delay (tc-q) is equal to two inverter delays plus the delay of
the transmission gate T2.
One important consideration for such a dynamic register is that the storage nodes
(i.e., the state) has to be refreshed at periodic intervals to prevent a loss due to charge leakage, due to diode leakage as well as sub-threshold currents. In datapath circuits, the refresh
rate is not an issue since the registers are periodically clocked, and the storage nodes are
constantly updated.
Clock overlap is an important concern for this register. Consider the clock waveforms shown in Figure 7.25. During the 0-0 overlap period, the NMOS of T1 and the
PMOS of T2 are simultaneously on, creating a direct path for data to flow from the D input
of the register to the Q output. This is known as a race condition. The output Q can change
on the falling edge if the overlap period is large — obviously an undesirable effect for a
positive edge-triggered register. The same is true for the 1-1 overlap region, where an
input-output path exists through the PMOS of T1 and the NMOS of T2. The latter case is
taken care off by enforcing a hold time constraint. That is, the data must be stable during
the high-high overlap period. The former situation (0-0 overlap) can be addressed by making sure that there is enough delay between the D input and node 2 ensuring that new data
sampled by the master stage does not propagate through to the slave stage. Generally the
built in single inverter delay should be sufficient and the overlap period constraint is given
as:
t overlap0 – 0 < t T1 + t I1 + t T2
(7.4)
chapter7.fm Page 315 Friday, January 18, 2002 9:09 AM
Section 7.3
Dynamic Latches and Registers
315
(0,0) overlap
CLK
(1,1) overlap
CLK
Figure 7.25 Impact of non-overlapping clocks.
Similarly, the constraint for the 1-1 overlap is given as:
t hold > t overlap1 – 1
7.3.2
(7.5)
C2MOS—A Clock-Skew Insensitive Approach
The C2MOS Register
Figure 7.26 shows an ingenious positive edge-triggered register, based on a master-slave
concept insensitive to clock overlap. This circuit is called the C2MOS (Clocked CMOS)
register [Suzuki73], and operates in two phases.
CLK
VDD
VDD
M2
M6
M4
CLK
M8
X
D
CLK
M3
M1
Master Stage
CL1
CLK
M7
M5
Q
CL2
Figure 7.26 C2MOS master-slave
positive edge-triggered register.
Slave Stage
1. CLK = 0 (CLK = 1): The first tri-state driver is turned on, and the master stage acts
as an inverter sampling the inverted version of D on the internal node X. The master
stage is in the evaluation mode. Meanwhile, the slave section is in a high-impedance
mode, or in a hold mode. Both transistors M7 and M8 are off, decoupling the output
from the input. The output Q retains its previous value stored on the output capacitor
CL2.
2. The roles are reversed when CLK = 1: The master stage section is in hold mode (M3M4 off), while the second section evaluates (M7-M8 on). The value stored on CL1
propagates to the output node through the slave stage which acts as an inverter.
chapter7.fm Page 316 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
316
Chapter 7
The overall circuit operates as a positive edge-triggered master-slave register —
very similar to the transmission-gate based register presented earlier. However, there is an
important difference:
A C2MOS register with CLK-CLK clocking is insensitive to overlap, as long as the rise and
fall times of the clock edges are sufficiently small.
To prove the above statement, we examine both the (0-0) and (1-1) overlap cases
(Figure 7.25). In the (0-0) overlap case, the circuit simplifies to the network shown in Figure 7.27a in which both PMOS devices are on during this period. The question is does any
new data sampled during the overlap window propagate to the output Q. This is not desirable since data should not change on the negative edge for a positive edge-triggered register. Indeed new data is sampled on node X through the series PMOS devices M2-M4, and
node X can make a 0-to-1 transition during the overlap period. However, this data cannot
propagate to the output since the NMOS device M7 is turned off. At the end of the overlap
period, CLK=1 and both M7 and M8 turn off, putting the slave stage is in the hold mode.
Therefore, any new data sampled on the falling clock edge is not seen at the slave output
Q, since the slave state is off till the next rising edge of the clock. As the circuit consists of
a cascade of inverters, signal propagation requires one pull-up followed by a pull-down, or
vice-versa, which is not feasible in the situation presented.
The (1-1) overlap case (Figure 7.27b), where both NMOS devices M3 and M7 are
turned on, is somewhat more contentious. The question is again if new data sampled during the overlap period (right after clock goes high) propagates to the Q output. A positive
edge-triggered register may only pass data that is presented at the input before the rising
edge. If the D input changes during the overlap period, node X can make a 1-to-0 transition, but cannot propagate to the output. However, as soon as the overlap period is over,
the PMOS M8 is turned on and the 0 propagates to output. This effect is not desirable. The
0
VDD
VDD
M2
M6
M4
D
X
0
VDD
M2
M8
(a) (0-0) overlap
M5
M6
X
Q D
1
M1
VDD
M3
M1
Q
1
M7
M5
(b) (1-1) overlap
Figure 7.27
C2MOS D-FF during overlap periods. No feasible signal path can exist between
In and D, as illustrated by the arrows.
problem is fixed by imposing a hold time constraint on the input data, D, or, in other
words, the data D should be stable during the overlap period.
In summary, it can be stated that the C2MOS latch is insensitive to clock overlaps
because those overlaps activate either the pull-up or the pull-down networks of the latches,
chapter7.fm Page 317 Friday, January 18, 2002 9:09 AM
Section 7.3
Dynamic Latches and Registers
317
but never both of them simultaneously. If the rise and fall times of the clock are sufficiently slow, however, there exists a time slot where both the NMOS and PMOS transistors are conducting. This creates a path between input and output that can destroy the state
of the circuit. Simulations have shown that the circuit operates correctly as long as the
clock rise time (or fall time) is smaller than approximately five times the propagation
delay of the register. This criterion is not too stringent, and is easily met in practical
designs. The impact of the rise and fall times is illustrated in Figure 7.28, which plots the
simulated transient response of a C2MOS D FF for clock slopes of respectively 0.1 and 3
nsec. For slow clocks, the potential for a race condition exists.
3.0
2.5
Volts
Q(3)
X(3)
2.0
CLK(3)
1.5
X(0.1)
CLK(0.1)
1.0
Q(0.1)
0.5
Figure 7.28 Transient response of
C2MOS FF for 0.1 nsec and 3 nsec
clock rise (fall) times assuming In = 1.
0.0
-0.5
0
2
4
time (nsec)
6
8
Dual-edge Registers
So far, we have focused on edge-triggered registers that sample the input data on only one
of the clock edges (rising or falling). It is also possible to design sequential circuits that
sample the input on both edges. The advantage of this scheme is that a lower frequency
clock (half of the original rate) is distributed for the same functional throughput, resulting
in power savings in the clock distribution network. Figure 7.29 shows a modification of
the C2MOS register to enable sampling on both edges. It consists of two parallel masterslave based edge-triggered registers, whose outputs are multiplexed using the tri-state
drivers.
When clock is high, the positive latch composed of transistors M1-M4 is sampling
the inverted D input on node X. Node Y is held stable, since devices M9 and M10 are turned
off. On the falling edge of the clock, the top slave latch M5-M8 turns on, and drives the
inverted value of X to the Q output. During the low phase, the bottom master latch (M1,
M4, M9, M10) is turned on, sampling the inverted D input on node Y. Note that the devices
M1 and M4 are reused, reducing the load on the D input. On the rising edge, the bottom
slave latch conducts, and drives the inverted version of Y on node Q. Data hence changes
on both edges. Note that the slave latches operate in a complementary fashion — this is,
only one of them is turned on during each phase of the clock.
chapter7.fm Page 318 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
318
VDD
VDD
M4
CLK
Chapter 7
n1
M3
M8
X
CLK
M7
CLK
M6
D
CLK
M2
n2
M1
M5
Q
VDD
M14
n1
CLK
M10 Y
CLK
M13
CLK
M9
CLK
M12
n2
M11
Figure 7.29 C2MOS based dual-edge triggered register.
Problem 7.6 Dual-edge registers
Determine how the adoption of dual-edge registers influences the power-dissipation in the
clock-distribution network.
7.3.3
True Single-Phase Clocked Register (TSPCR)
In the two-phase clocking schemes described above, care must be taken in routing the two
clock signals to ensure that overlap is minimized. While the C2MOS provides a skew-tolerant solution, it is possible to design registers that only use a single phase clock. The True
Single-Phase Clocked Register (TSPCR), proposed by Yuan and Svensson, uses a single
clock [Yuan89]. The basic single-phase positive and negative latches are shown in Figure
7.30. For the positive latch, when CLK is high, the latch is in the transparent mode and
VDD
VDD
VDD
VDD
Out
In
In
CLK
CLK
Positive Latch
Figure 7.30
CLK
CLK
Out
Negative Latch
True Single Phase Latches.
chapter7.fm Page 319 Friday, January 18, 2002 9:09 AM
Section 7.3
Dynamic Latches and Registers
319
corresponds to two cascaded inverters; the latch is non-inverting, and propagates the input
to the output. On the other hand, when CLK = 0, both inverters are disabled, and the latch
is in hold-mode. Only the pull-up networks are still active, while the pull-down circuits are
deactivated. As a result of the dual-stage approach, no signal can ever propagate from the
input of the latch to the output in this mode. A register can be constructed by cascading
positive and negative latches. The clock load is similar to a conventional transmission gate
register, or C2MOS register. The main advantage is the use of a single clock phase. The
disadvantage is the slight increase in the number of transistors — 12 transistors are
required.
TSPC offers an additional advantage: the possibility of embedding logic functionality into the latches. This reduces the delay overhead associated with the latches. Figure
7.31a outlines the basic approach for embedding logic, while Figure 7.31b shows an
example of a positive latch that implements the AND of In1 and In2 in addition to performing the latching function. While the set-up time of this latch has increased over the one
shown in Figure 7.30, the overall performance of the digital circuit (that is, the clock
period of a sequential circuit) has improved: the increase in set-up time is typically smaller
than the delay of an AND gate. This approach of embedding logic into latches has been
used extensively in the design of the EV4 DEC Alpha microprocessor [Dobberpuhl92]
and many other high performance processors.
VDD
VDD
VDD
In1
VDD
In2
Q
PUN
Q
In
CLK
CLK
CLK
CLK
In1
PDN
In2
(a) Including logic into the latch
Figure 7.31
(b) AND latch
Adding logic to the TSPC approach.
Example 7.4 Impact of embedding logic into latches on performance
Consider embedding an AND gate into the TSPC latch, as shown in Figure 7.31b. In a 0.25
µm, the set-up time of such a circuit using minimum-size devices is 140 psec. A conventional
approach, composed of an AND gate followed by a positive latch has an effective set-up time
of 600 psec (we treat the AND plus latch as a black box that performs both functions). The
embedded logic approach hence results in significant performance improvements.
The TSPC latch circuits can be further reduced in complexity, as illustrated in Figure 7.32, where only the first inverter is controlled by the clock. Besides the reduced number of transistors, these circuits have the advantage that the clock load is reduced by half.
On the other hand, not all node voltages in the latch experience the full logic swing. For
instance, the voltage at node A (for Vin = 0 V) for the positive latch maximally equals VDD
– VTn, which results in a reduced drive for the output NMOS transistor and a loss in perfor-
chapter7.fm Page 320 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
320
VDD
VDD
In
CLK
VDD
VDD
Out
In
A
(a) Positive Latch
CLK
Chapter 7
Figure 7.32 Simplified TSPC latch
(also called split-output).
Out
A
(b) Negative Latch
mance. Similarly, the voltage on node A (for Vin = VDD) for the negative latch is only
driven down to |VTp|. This also limits the amount of VDD scaling possible on the latch.
Figure 7.33 shows the design of a specialized single-phase edge-triggered register.
When CLK = 0, the input inverter is sampling the inverted D input on node X. The second
(dynamic) inverter is in the precharge mode, with M6 charging up node Y to VDD. The third
inverter is in the hold mode, since M8 and M9 are off. Therefore, during the low phase of
the clock, the input to the final (static) inverter is holding its previous value and the output
Q is stable. On the rising edge of the clock, the dynamic inverter M4-M6 evaluates. If X is
high on the rising edge, node Y discharges. The third inverter M7-M8 is on during the high
phase, and the node value on Y is passed to the output Q. On the positive phase of the
clock, note that node X transitions to a low if the D input transitions to a high level. Therefore, the input must be kept stable till the value on node X before the rising edge of the
clock propagates to Y. This represents the hold time of the register (note that the hold time
less than 1 inverter delay since it takes 1 delay for the input to affect node X). The propagation delay of the register is essentially three inverters since the value on node X must
propagate to the output Q. Finally, the set-up time is the time for node X to be valid, which
is one inverter delay.
VDD
M3
D
CLK
M2
M1
VDD
CLK
VDD
M6
M9
Y
X
CLK
M5
M4
Q
Q
CLK
M8
M7
Figure 7.33
TSPC.
Positive edge-triggered register
WARNING: Similar to the C2MOS latch, the TSPC latch malfunctions when the slope of
the clock is not sufficiently steep. Slow clocks cause both the NMOS and PMOS clocked
transistors to be on simultaneously, resulting in undefined values of the states and race
conditions. The clock slopes should therefore be carefully controlled. If necessary, local
buffers must be introduced to ensure the quality of the clock signals.
chapter7.fm Page 321 Friday, January 18, 2002 9:09 AM
Section 7.4
Alternative Register Styles
321
Example 7.5 TSPC Edge-Triggered Register
Transistor sizing is critical for achieving correct functionality in the TSPC register. With
improper sizing, glitches may occur at the output due to a race condition when the clock transitions from low to high. Consider the case where D is low and Q=1 (Q=0). While CLK is
low, Y is pre-charged high turning on M7. When CLK transitions from low to high, nodes Y
and Q start to discharge simultaneously (through M4-M5 and M7-M8, respectively). Once Y is
sufficiently low, the trend on Q is reversed and the node is pulled high anew through M9. In a
sense, this chain of events is comparable to what would happen if we chain dynamic logic
gates. Figure 7.34 shows the transient response of the circuit of Figure 7.33 for different sizes
of devices in the final two stages.
3.0
Qmodified Qoriginal
Volts
2.0
CLK
M4 , M 5
M7 , M 8
Original
Width
0.5µm
2µm
Modified
Width
1µm
1µm
1.0
Qoriginal
Figure 7.34 Transistor sizing issues in TSPC
(for the register of Figure 7.33).
Qmodified
0.0
0.0
0.2
0.4
0.6
time (nsec)
0.8
1.0
This glitch may be the cause of fatal errors, as it may create unwanted events (for
instance, when the output of the latch is used as a clock signal input to another register). It
also reduces the contamination delay of the register. The problem can be corrected by resizing the relative strengths of the pull-down paths through M4-M5 and M7-M8, so that Y discharges much faster than Q. This is accomplished by reducing the strength of the M7-M8
pulldown path, and by speeding up the M4 -M5 pulldown path.
7.4
Alternative Register Styles
7.4.1
Pulse Registers
Until now, we have used the master-slave configuration to create an edge-triggered register. A fundamentally different approach for constructing a register uses pulse signals. The
idea is to construct a short pulse around the rising (or falling) edge of the clock. This pulse
acts as the clock input to a latch (e.g., a TSPC flavor is shown in Figure 7.35a), sampling
the input only in a short window. Race conditions are thus avoided by keeping the opening
time (i.e, the transparent period) of the latch very short. The combination of the glitchgeneration circuitry and the latch results in a positive edge-triggered register.
Figure 7.35b shows an example circuit for constructing a short intentional glitch on
each rising edge of the clock [Kozu96]. When CLK = 0, node X is charged up to VDD (MN
is off since CLKG is low). On the rising edge of the clock, there is a short period of time
when both inputs of the AND gate are high, causing CLKG to go high. This in turn acti-
chapter7.fm Page 322 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
322
VDD
VDD
M3
M6
VDD
CLK
Q
D
CLKG
M2
Chapter 7
CLKG
MP
M5
CLKG
X
MN
M1
M4
(b) glitch generation
(a) register
CLK
CLKG
(c) glitch clock
Figure 7.35 Glitch latch - timing generation and register.
vates MN, pulling X and eventually CLKG low (Figure 7.35c). The length of the pulse is
controlled by the delay of the AND gate and the two inverters. Note that there exists also a
delay between the rising edges of the input clock (CLK) and the glitch clock (CLKG) —
also equal to the delay of the AND gate and the two inverters. If every register on the chip
uses the same clock generation mechanism, this sampling delay does not matter. However,
process variations and load variations may cause the delays through the glitch clock circuitry to be different. This must be taken into account when performing timing verification and clock skew analysis (which is the topic of a later Chapter).
If set-up time and hold time are measured in reference to the rising edge of the glitch
clock, the set-up time is essentially zero, the hold time is equal to the length of the pulse (if
the contamination delay is zero for the gates), and the propagation delay (tc-q) equals two
gate delays. The advantage of the approach is the reduced clock load and the small number
of transistors required. The glitch-generation circuitry can be amortized over multiple register bits. The disadvantage is a substantial increase in verification complexity. This has
prevented a wide-spread use. They do however provide an alternate approach to conventional schemes, and have been adopted in some high performance processors (e.g.,
[Kozu96]).
Another version of the pulsed register is shown in Figure 7.36 (as used in the AMDK6 processor [Partovi96]). When the clock is low, M3 and M6 are off, and device P1 is
turned on. Node X is precharged to VDD, the output node (Q) is decoupled from X and is
held at its previous state. CLKD is a delay-inverted version of CLK. On the rising edge of
the clock, M3 and M6 turn on while devices M1 and M4 stay on for a short period, determined by the delay of the three inverters. During this interval, the circuit is transparent
and the input data D is sampled by the latch. Once CLKD goes low, node X is decoupled
from the D input and is either held or starts to precharge to VDD by PMOS device P2. On
the falling edge of the clock, node X is held at VDD and the output is held stable by the
cross-coupled inverters.
Note that this circuit also uses a one-shot, but the one-shot is integrated into the reg-
chapter7.fm Page 323 Friday, January 18, 2002 9:09 AM
Section 7.4
Alternative Register Styles
CLK
323
P1
P3
x
Q
M6
M3
D
P2
M2
M1
M5
M4
Figure 7.36 Flow-through positive
edge-triggered register.
CLKD
ister. The transparency period also determines the hold time of the register. The window
must be wide enough for the input data to propagate to the Q output. In this particular circuit, the set-up time can be negative. This is the case if the transparency window is longer
than the delay from input to output. This is attractive, as data can arrive at the register even
after the clock goes high, which means that time is borrowed from the previous cycle.
Example 7.6 Set-up time of glitch register
The glitch register of Figure 7.36 is transparent during the (1-1) overlap of CLK and CLKD.
As a result, the input data can actually change after the rising edge of the clock, resulting in a
negative set-up time (Figure 7.37). The D-input transitions to low after the rising edge of the
clock, and transitions high before the falling edge of CLKD (this is, during the transparency
period). Observe how the output follows the input. The output Q does go to the correct value
of VDD as long as the input D is set up correctly some time before the falling edge of CLKD.
When the negative set-up time is exploited, there can be no guarantees on the monotonic
behavior of the output. That is, the output can have multiple transitions around the rising
edge, and therefore, the output of the register should not be used as a clock to other registers.
3.0
2.5
Volts
Q
D
2.0
1.5
1.0
0.5
CLK
CLKD
Figure 7.37 Simulation showing a
negative set-up time for the glitch
register.
0.0
-0.5
0.0
Problem 7.7
0.2
0.4
0.6
time (nsec)
0.8
1.0
Converting a glitch register to a conditional glitch register
Modify the circuit in Figure 7.36 so that it takes an additional Enable input. The goal is to
convert the register to a conditional register which latches only when the enable signal is
asserted.
chapter7.fm Page 324 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
324
7.4.2
Chapter 7
Sense-Amplifier Based Registers
So far, we have presented two fundamental approaches towards building edge-triggered
registers: the master-slave concept and the glitch technique. Figure 7.38 introduces
another technique that uses a sense amplifier structure to implement an edge-triggered
register [Montanaro96]. Sense-amplifier circuits accept small input signals and amplify
them to generate rail-to-rail swings. As we will see, sense amplifier circuits are used
extensively in memory cores and in low swing bus drivers to amplify small voltage swings
present in heavily loaded wires. There are many techniques to construct these amplifiers,
with the use of feedback (e.g., cross-coupled inverters) being one common approach. The
circuit shown in Figure 7.38 uses a precharged front-end amplifier that samples the differential input signal on the rising edge of the clock signal. The outputs of front-end are fed
into a NAND cross-coupled SR FF that holds the data and guarantees that the differential
outputs switch only once per clock cycle. The differential inputs in this implementation
don’t have to have rail-to-rail swing and hence this register can be used as a receiver for a
reduced swing differential bus.
The core of the front-end consists of a cross-coupled inverter (M5-M8), whose outputs (L1 and L2) are precharged using devices M9 and M10 during the low phase of the
clock. As a result, PMOS transistors M7 and M8 to be turned off and the NAND FF is
holding its previous state. Transistor M1 is similar to an evaluate switch in dynamic circuits and is turned off ensuring that the differential inputs don’t affect the output during
the low phase of the clock. On the rising edge of the clock, the evaluate transistor turns on
and the differential input pair (M2 and M3) is enabled, and the difference between the input
signals is amplified on the output nodes on L1 and L2. The cross-coupled inverter pair flips
to one of its the stable states based on the value of the inputs. For example, if IN is 1, L1 is
pulled to 0, and L2 remains at VDD. Due to the amplifying properties of the input stage, it is
not necessary for the input to swing all the way up to VDD and enables the use of lowswing signaling on the input wires.
The shorting transistor, M4, is used to provide a DC leakage path from either node
L3, or L4, to ground. This is necessary to accommodate the case where the inputs change
OUT
OUT
VDD
VDD
M9
M7
M8
M10
L1
L2
M5
M6
M4
IN
CLK
L3
M2
VDD
M1
L4
M3
IN
Figure 7.38 Positive edge-triggered
register based on sense-amplifier.
chapter7.fm Page 325 Friday, January 18, 2002 9:09 AM
Section 7.5
Pipelining: An approach to optimize sequential circuits
325
Initially
0
L1
L2
high
impedance
L3
w/o shorting
device
0
IN
1 0
1
1 0 L4
w/shorting
device
IN
0 1
Inputs Change (CLK still high)
0 1
0 0
L1
L2
leakage path
L3
IN
1 0
0 1
1 0
0 L4
L1
leakage path
L3
IN
0 1
L3 is isolated so charge accumulates
until L1/L3 change state,
causing L2 to change state as well.
As a result the flip-flop outputs change.
IN
1 0
L2
0 0
1 1
1 0 L4
IN
0 1
The leakage current attempts to
charge L1/L3 but the DC path
through the shorting transistor
allows it to leak away to ground.
Figure 7.39 The need for the shorting transistor M4.
their value after the positive edge of CLK has occurred, resulting in either L3 or L4 being
left in a high-impedance state with a logical low voltage level stored on the node. Without
the leakage path that node would be susceptible to charging by leakage currents. The latch
could then actually change state prior to the next rising edge of CLK! This is best illustrated graphically, as shown in Figure 7.39.
7.5
Pipelining: An approach to optimize sequential circuits
Pipelining is a popular design technique often used to accelerate the operation of the datapaths in digital processors. The idea is easily explained with the example of Figure 7.40a.
The goal of the presented circuit is to compute log(|a − b|), where both a and b represent
streams of numbers, that is, the computation must be performed on a large set of input values. The minimal clock period Tmin necessary to ensure correct evaluation is given as:
T min = t c-q + t pd,logic + t su
(7.6)
where tc-q and tsu are the propagation delay and the set-up time of the register, respectively. We assume that the registers are edge-triggered D registers. The term tpd,logic stands
for the worst-case delay path through the combinational network, which consists of the
adder, absolute value, and logarithm functions. In conventional systems (that don’t push
the edge of technology), the latter delay is generally much larger than the delays associated with the registers and dominates the circuit performance. Assume that each logic
module has an equal propagation delay. We note that each logic module is then active for
only 1/3 of the clock period (if the delay of the register is ignored). For example, the adder
chapter7.fm Page 326 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
326
Chapter 7
unit is active during the first third of the period and remains idle—this is, it does no useful
computation— during the other 2/3 of the period. Pipelining is a technique to improve the
resource utilization, and increase the functional throughput. Assume that we introduce
registers between the logic blocks, as shown in Figure 7.40b. This causes the computation
for one set of input data to spread over a number of clock periods, as shown in Table 7.1.
The result for the data set (a1, b1) only appears at the output after three clock-periods. At
that time, the circuit has already performed parts of the computations for the next data
sets, (a2, b2) and (a3,b3). The computation is performed in an assembly-line fashion, hence
the name pipeline.
Table 7.1 Example of pipelined computations.
Clock Period
Adder
1
a1 + b1
2
a2 + b2
Absolute Value
Logarithm
|a1 + b1|
3
a3 + b3
|a2 + b2|
log(|a1 + b1|)
4
a4 + b4
|a3 + b3|
log(|a2 + b2|)
5
a5 + b5
|a4 + b4|
log(|a3 + b3|)
The advantage of pipelined operation becomes apparent when examining the minimum clock period of the modified circuit. The combinational circuit block has been partitioned into three sections, each of which has a smaller propagation delay than the original
function. This effectively reduces the value of the minimum allowable clock period:
.
b
log
REG
CLK
REG
a
(7.7)
REG
T min,pipe = t c-q + max (t pd,add,t pd,abs, t pd ,log)
Out
(a) Reference circuit
CLK
CLK
log
REG
CLK
.
REG
REG
b
CLK
REG
a
REG
CLK
Out
CLK
(b) Pipelined version
CLK
Figure 7.40
Datapath for the computation of log(|a + b|).
chapter7.fm Page 327 Friday, January 18, 2002 9:09 AM
Section 7.5
Pipelining: An approach to optimize sequential circuits
327
Suppose that all logic blocks have approximately the same propagation delay, and
that the register overhead is small with respect to the logic delays. The pipelined network
outperforms the original circuit by a factor of three under these assumptions, or T min,pipe=
Tmin/3. The increased performance comes at the relatively small cost of two additional registers, and an increased latency.2 This explains why pipelining is popular in the implementation of very high-performance datapaths.
7.5.1
Latch- vs. Register-Based Pipelines
Pipelined circuits can be constructed using level-sensitive latches instead of edge-triggered registers. Consider the pipelined circuit of Figure 7.41. The pipeline system is
implemented based on pass-transistor-based positive and negative latches instead of edgetriggered registers. That is, logic is introduced between the master and slave latches of a
master-slave system. In the following discussion, we use without loss of generality the
CLK-CLK notation to denote a two-phase clock system. Latch-based systems give significantly more flexibility in implementing a pipelined system, and often offers higher performance. When the clocks CLK and CLK are non-overlapping, correct pipeline operation is
obtained. Input data is sampled on C1 at the negative edge of CLK and the computation of
CLK
CLK
CLK
Out
In
F
G
C1
C2
C3
CLK
CLK
Compute F
compute G
Figure 7.41 Operation of two-phase
pipelined circuit using dynamic registers.
logic block F starts; the result of the logic block F is stored on C2 on the falling edge of
CLK, and the computation of logic block G starts. The non-overlapping of the clocks
ensures correct operation. The value stored on C2 at the end of the CLK low phase is the
result of passing the previous input (stored on the falling edge of CLK on C1) through the
logic function F. When overlap exists between CLK and CLK, the next input is already
being applied to F, and its effect might propagate to C2 before CLK goes low (assuming
that the contamination delay of F is small). In other words, a race develops between the
previous input and the current one. Which value wins depends upon the logic function F,
the overlap time, and the value of the inputs since the propagation delay is often a func2
Latency is defined here as the number of clock cycles it takes for the data to propagate from the input to
the output. For the example at hand, pipelining increases the latency from 1 to 3. An increased latency is in general acceptable, but can cause a global performance degradation if not treated with care.
chapter7.fm Page 328 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
328
Chapter 7
tion of the applied inputs. The latter factor makes the detection and elimination of race
conditions non-trivial.
7.5.2
NORA-CMOS—A Logic Style for Pipelined Structures
The latch-based pipeline circuit can also be implemented using C2MOS latches, as shown
in Figure 7.42. The operation is similar to the one discussed above. This topology has one
additional, important property:
A C2MOS-based pipelined circuit is race-free as long as all the logic functions F (implemented using static logic) between the latches are non-inverting.
The reasoning for the above argument is similar to the argument made in the construction of a C2MOS register. During a (0-0) overlap between CLK and CLK, all C2MOS
latches, simplify to pure pull-up networks (see Figure 7.27). The only way a signal can
VDD
VDD
VDD
CLK
CLK
In
CLK
F
CLK
CLK
C1
Figure 7.42
Out
G
C2
CLK
C3
Pipelined datapath using C 2MOS latches.
race from stage to stage under this condition is when the logic function F is inverting, as
illustrated in Figure 7.43, where F is replaced by a single, static CMOS inverter. Similar
considerations are valid for the (1-1) overlap.
VDD
VDD
VDD
CLK
CLK
CLK
CLK
0
Figure 7.43 Potential race condition
during (0-0) overlap in C 2MOS-based
design.
Based on this concept, a logic circuit style called NORA-CMOS was conceived
[Goncalves83]. It combines C2MOS pipeline registers and NORA dynamic logic function
blocks. Each module consists of a block of combinational logic that can be a mixture of
static and dynamic logic, followed by a C2MOS latch. Logic and latch are clocked in such
a way that both are simultaneously in either evaluation, or hold (precharge) mode. A block
that is in evaluation during CLK = 1 is called a CLK-module, while the inverse is called a
chapter7.fm Page 329 Friday, January 18, 2002 9:09 AM
Section 7.5
Pipelining: An approach to optimize sequential circuits
329
CLK-module. Examples of both classes are shown in Figure 7.44 a and b, respectively.
The operation modes of the modules are summarized in Table 7.2.
VDD
CLK
VDD
VDD
CLK
CLK
In1
In2
In3
Out
PUN
PDN
CLK
CLK
CLK
Combinational logic
Latch
(a) CLK-module
VDD
CLK
VDD
VDD
VDD
In4
CLK
Out
In1
In2
In3
PDN
CLK
CLK
In4
(b) CLK-module
Figure 7.44
Examples of NORA CMOS Modules.
Table 7.2 Operation modes for NORA logic modules.
CLK block
CLK = 0
CLK = 1
CLK block
Logic
Latch
Logic
Latch
Precharge
Hold
Evaluate
Evaluate
Evaluate
Evaluate
Precharge
Hold
A NORA datapath consists of a chain of alternating CLK and CLK modules. While
one class of modules is precharging with its output latch in hold mode, preserving the previous output value, the other class is evaluating. Data is passed in a pipelined fashion from
module to module.
NORA offers designers a wide range of design choices. Dynamic and static logic
can be mixed freely, and both CLKp and CLKn dynamic blocks can be used in cascaded or
in pipelined form. With this freedom of design, extra inverter stages, as required in
DOMINO-CMOS, are most often avoided.
chapter7.fm Page 330 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
330
Chapter 7
Design Rules
In order to ensure correct operation, two important rules should always be followed:
• The dynamic-logic rule: Inputs to a dynamic CLKn (CLKp) block are only allowed to
make a single 0 → 1 (1 → 0) transition during the evaluation period (Chapter 6).
• The C2MOS rule: In order to avoid races, the number of static inversions between
C2MOS latches should be even.
The presence of dynamic logic circuits requires the introduction of some extensions
to the latter rule. Consider the situation pictured in Figure 7.45a. During precharge (CLK =
0), the output register of the module has to be in hold mode, isolating the output node from
the internal events in the module. Assume now that a (0-0) overlap occurs. Node A gets
precharged to VDD, while the latch simplifies to a pull-up network (Figure 7.45b). It can be
observed that under those circumstances the output node charges to VDD, and the stored
value is erased! This malfunctioning is caused by the fact that the number of static inversions between the last dynamic node in the module and the latch is odd, which creates an
active path between the precharged node and the output. This translates into the following
rule: The number of static inversions between the last dynamic block in a logic function
and the C2MOS latch should be even. This and similar considerations lead to a reformulated C2MOS rule [Goncalvez83].
Revised C2MOS Rule
• The number of static inversions between C2MOS latches should be even (in the absence
of dynamic nodes); if dynamic nodes are present, the number of static inverters between
VDD
VDD
VDD
VDD
VDD
CLK
CLK
A
A
CLK
CLK
Out
In1
PDN
In2
VDD
CLK
CLK
(a) Circuit with odd number of static inversions
between dynamic logic stage and register
Out
In1
PDN
In2
CLK
CLK
(b) Same circuit during (0-0) clock overlap.
Figure 7.45
Extended C2MOS rules.
chapter7.fm Page 331 Friday, January 18, 2002 9:09 AM
Section 7.6
Non-Bistable Sequential Circuits
331
a latch and a dynamic gate in the logic block should be even. The number of static inversions between the last dynamic gate in a logic block and the latch should be even as well.
Adhering to the above rules is not always trivial and requires a careful analysis of
the logic equations to be implemented. This often makes the design of an operational
NORA-CMOS structure cumbersome. Its use should only be considered when maximum
circuit performance is a must.
7.6
Non-Bistable Sequential Circuits
In the preceding sections, we have focused on one single type of sequential element, this is
the latch (and its sibling the register). The most important property of such a circuit is that
it has two stable states, and is hence called bistable. The bistable element is not the only
sequential circuit of interest. Other regenerative circuits can be catalogued as astable and
monostable. The former act as oscillators and can, for instance, be used for on-chip clock
generation. The latter serve as pulse generators, also called one-shot circuits. Another
interesting regenerative circuit is the Schmitt trigger. This component has the useful property of showing hysteresis in its dc characteristics—its switching threshold is variable and
depends upon the direction of the transition (low-to-high or high-to-low). This peculiar
feature can come in handy in noisy environments.
7.6.1
The Schmitt Trigger
Definition
A Schmitt trigger [Schmitt38] is a device with two important properties:
1. It responds to a slowly changing input waveform with a fast transition time at the
output.
2. The voltage-transfer characteristic of the device displays different switching thresholds for positive- and negative-going input signals. This is demonstrated in Figure
7.46, where a typical voltage-transfer characteristic of the Schmitt trigger is shown
(and its schematics symbol). The switching thresholds for the low-to-high and highto-low transitions are called VM+ and VM−, respectively. The hysteresis voltage is
defined as the difference between the two.
One of the main uses of the Schmitt trigger is to turn a noisy or slowly varying input signal
into a clean digital output signal. This is illustrated in Figure 7.47. Notice how the hysteresis suppresses the ringing on the signal. At the same time, the fast low-to-high (and highto-low) transitions of the output signal should be observed. For instance, steep signal
slopes are beneficial in reducing power consumption by suppressing direct-path currents.
The “secret” behind the Schmitt trigger concept is the use of positive feedback.
chapter7.fm Page 332 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
332
Chapter 7
VOH
Vout
In
Out
VOL
(b) Schematic symbol
VM–
VM+
Vin
(a) Voltage-transfer characteristic
Figure 7.46
Non-inverting Schmitt trigger.
CMOS Implementation
One possible CMOS implementation of the Schmitt trigger is shown in Figure 7.48. The
idea behind this circuit is that the switching threshold of a CMOS inverter is determined
by the (kn/kp) ratio between the NMOS and PMOS transistors. Increasing the ratio results
in a reduction of the threshold, while decreasing it results in an increase in VM. Adapting
the ratio depending upon the direction of the transition results in a shift in the switching
threshold and a hysteresis effect. This adaptation is achieved with the aid of feedback.
Suppose that Vin is initially equal to 0, so that Vout = 0 as well. The feedback loop
biases the PMOS transistor M4 in the conductive mode while M3 is off. The input signal
effectively connects to an inverter consisting of two PMOS transistors in parallel (M2 and
M4) as a pull-up network, and a single NMOS transistor (M1) in the pull-down chain. This
modifies the effective transistor ratio of the inverter to kM1/(kM2+kM4), which moves the
switching threshold upwards.
Once the inverter switches, the feedback loop turns off M4, and the NMOS device
M3 is activated. This extra pull-down device speeds up the transition and produces a clean
output signal with steep slopes.
A similar behavior can be observed for the high-to-low transition. In this case, the
pull-down network originally consists of M1 and M3 in parallel, while the pull-up network
is formed by M2. This reduces the value of the switching threshold to VM–.
Vin
Vout
VM+
VM–
t0
Figure 7.47
t
Noise suppression using a Schmitt trigger.
t0 + tp
t
chapter7.fm Page 333 Friday, January 18, 2002 9:09 AM
Section 7.6
Non-Bistable Sequential Circuits
333
VDD
M4
M2
X
Vin
Vout
M3
M1
Figure 7.48
Example 7.7
CMOS Schmitt trigger.
CMOS Schmitt Trigger
Consider the schmitt trigger with the following device sizes. Devices M1 and M2 are
1µm/0.25µm, and 3µm/0.25µm, respectively. The inverter is sized such that the switching
threshold is around VDD/2 (= 1.25 V). Figure 7.49a shows the simulation of the Schmitt trigger assuming that devices M3 and M4 are 0.5µm/0.25µm and 1.5µm/0.25µm, respectively. As
apparent from the plot, the circuit exhibits hysteresis. The high-to-low switching point (VM- =
0.9 V) is lower than VDD/2, while the low-to-high switching threshold (VM+ = 1.6 V) is larger
than VDD/2.
2.5
2.5
2.0
2.0
VM+
1.5
Vx (V)
VX (V)
1.5
VM-
1.0
1.0
k=3
k=1
0.5
0.5
0.0
0.0
0.5
1.0
1.5
2.0
2.5
Vin(V)
(a) Voltage-transfer characteristics with hysteresis.
0.0
0.0
k=4
k=2
0.5
1.0
1.5
2.0
2.5
Vin(V)
(b) The effect of varying the ratio of the
PMOS device M4. The width is k * 0.5µm.
Figure 7.49 Schmitt trigger simulations.
It is possible to shift the switching point by changing the sizes of M3 and M4. For
example, to modify the low-to-high transition, we need to vary the PMOS device. The highto-low threshold is kept constant by keeping the device width of M3 at 0.5 µm. The device
width of M4 is varied as k * 0.5µm. Figure 7.49b demonstrates how the switching threshold
increases with raising values of k.
chapter7.fm Page 334 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
334
Problem 7.8
Chapter 7
An Alternative CMOS Schmitt Trigger
Another CMOS Schmitt trigger is shown in Figure 7.50. Discuss the operation of the gate,
and derive expressions for VM− and VM+.
VDD
M4
M6
M3
In
Out
M2
X
M5
VDD
M1
Figure 7.50
7.6.2
Alternate CMOS Schmitt trigger.
Monostable Sequential Circuits
A monostable element is a circuit that generates a pulse of a predetermined width every
time the quiescent circuit is triggered by a pulse or transition event. It is called monostable
because it has only one stable state (the quiescent one). A trigger event, which is either a
signal transition or a pulse, causes the circuit to go temporarily into another quasi-stable
state. This means that it eventually returns to its original state after a time period determined by the circuit parameters. This circuit, also called a one-shot, is useful in generating
pulses of a known length. This functionality is required in a wide range of applications.
We have already seen the use of a one-shot in the construction of glitch registers. Another
notorious example is the address transition detection (ATD) circuit, used for the timing
generation in static memories. This circuit detects a change in a signal, or group of signals,
such as the address or data bus, and produces a pulse to initialize the subsequent circuitry.
The most common approach to the implementation of one-shots is the use of a simple delay element to control the duration of the pulse. The concept is illustrated in Figure
7.51. In the quiescent state, both inputs to the XOR are identical, and the output is low. A
transition on the input causes the XOR inputs to differ temporarily and the output to go
high. After a delay td (of the delay element), this disruption is removed, and the output
goes low again. A pulse of length td is created. The delay circuit can be realized in many
different ways, such as an RC-network or a chain of basic gates.
In
DELAY
td
Figure 7.51
Transition-triggered one-shot.
Out
td
chapter7.fm Page 335 Friday, January 18, 2002 9:09 AM
Section 7.6
Non-Bistable Sequential Circuits
7.6.3
335
Astable Circuits
An astable circuit has no stable states. The output oscillates back and forth between two
quasi-stable states with a period determined by the circuit topology and parameters (delay,
power supply, etc.). One of the main applications of oscillators is the on-chip generation
of clock signals. This application is discussed in detail in a later chapter (on timing).
The ring oscillator is a simple, example of an astable circuit. It consists of an odd
number of inverters connected in a circular chain. Due to the odd number of inversions, no
stable operation point exists, and the circuit oscillates with a period equal to 2 × tp × N,
with N the number of inverters in the chain and tp the propagation delay of each inverter.
Example 7.8 Ring oscillator
The simulated response of a ring oscillator with five stages is shown in Figure 7.52 (all gates
use minimum-size devices). The observed oscillation period approximately equals 0.5 nsec,
which corresponds to a gate propagation delay of 50 psec. By tapping the chain at various
points, different phases of the oscillating waveform are obtained (phases 1, 3, and 5 are displayed in the plot). A wide range of clock signals with different duty-cycles and phases can be
derived from those elementary signals using simple logic operations.
The ring oscillator composed of cascaded inverters produces a waveform with a
fixed oscillating frequency determined by the delay of an inverter in the CMOS process.
In many applications, it is necessary to control the frequency of the oscillator. An example
of such a circuit is the voltage-controlled oscillator (VCO), whose oscillation frequency is
a function (typically non-linear) of a control voltage. The standard ring oscillator can be
modified into a VCO by replacing the standard inverter with a current-starved inverter as
shown in Figure 7.53 [Jeong87]. The mechanism for controlling the delay of each inverter
is to limit the current available to discharge the load capacitance of the gate.
In this modified inverter circuit, the maximal discharge current of the inverter is limited by adding an extra series device. Note that the low-to-high transition on the inverter
can also be controlled by adding a PMOS device in series with M2. The added NMOS
transistor M3, is controlled by an analog control voltage Vcntl, which determines the available discharge current. Lowering Vcntl reduces the discharge current and, hence, increases
tpHL. The ability to alter the propagation delay per stage allows us to control the frequency
of the ring structure. The control voltage is generally set using feedback techniques. Under
low operating current levels, the current-starved inverter suffers from slow fall times at its
3.0
v1 v3 v5
2.5
Volts
2.0
1.5
1.0
0.5
Figure 7.52 Simulated waveforms of
five-stage ring oscillator. The outputs
of stages 1, 3, and 5 are shown.
0.0
-0.5
0.0
0.5
time (nsec)
1.0
1.5
chapter7.fm Page 336 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
336
Chapter 7
VDD
M2
In
Out
M1
Iref
Vcntl
Figure 7.53
Voltage-controlled oscillator based on
current-starved inverters.
M3
output. This can result in significant short-circuit current. This is resolved by feeding its
output into a CMOS inverter or better yet a Schmitt trigger. An extra inverter is needed at
the end to ensure that the structure oscillates.
Example 7.9
Current-Starved Inverter Simulation
Figure 7.54 show the simulated delay of the current-starved inverter as a function of the control voltage Vcntl. The delay of the inverter can be varied over a large range. When the control
voltage is smaller than the threshold, the device enters the sub-threshold region. This results
in large variations of the propagation delay, as the drive current is exponentially dependent
on the drive voltage. When operating in this region, the delay is very sensitive to variations in
the control voltage, and, hence, to noise.
5.0
tpHL (nsec)
4.0
3.0
2.0
Figure 7.54 tpHL of current-starved
inverter as a function of the control
voltage.
1.0
0.0
0.5
1.0
1.5
Vctrl (V)
2.0
2.5
Another approach to implement the delay element is to use a differential element as
shown in Figure 7.55a. Since the delay cell provides both inverting and non-inverting outputs, an oscillator with an even number of stages can be implemented. Figure 7.55b shows
a two-stage differential VCO, where the feedback loop provides 180o phase shift through
two gate delays, one non-inverting and the other inverting, therefore forming an oscillation. The simulated waveforms of this two stage VCO are shown in Figure 7.55c. The inphase and quadrature phase outputs are available simultaneously. The differential type
chapter7.fm Page 337 Friday, January 18, 2002 9:09 AM
Section 7.7
Perspective: Choosing a Clocking Strategy
337
VCO has better immunity to common mode noise (for example, supply noise) compared to
the common ring oscillator. However, it consumes more power due to the increased complexity, and the static current.
Vo-
Vo+
in+
in-
v1
i+ o+
v2
i- o-
v3
v4
i+ o+
i- o-
Vctrl
(b) two stage VCO
(a) delay cell
3.0
2.5
v1 v2
v3
v4
Volts
2.0
1.5
1.0
0.5
0.0
-0.5
0.5
1.5
2.5
time (nsec)
(c) simulated waveforms of 2-stage VCO
7.7
3.5
Figure 7.55 Differential delay
element and VCO topology.
Perspective: Choosing a Clocking Strategy
A crucial decision that must be made in the earliest phases of a chip design is to select the
appropriate clocking methodology. The reliable synchronization of the various operations
occurring in a complex circuit is one of the most intriguing challenges facing the digital
designer of the next decade. Choosing the right clocking scheme affects the functionality,
speed and power of a circuit.
A number of widely-used clocking schemes were introduced in this chapter. The
most robust and conceptually simple scheme is the two-phase master-slave design. The
predominant approach is use the multiplexer-based register, and to generate the two clock
phases locally by simply inverting the clock. More exotic schemes such as the glitch register are also used in practice. However, these schemes require significant hand tuning and
must only be used in specific situations. An example of such is the need for a negative setup time to cope with clock skew.
The general trend in high-performance CMOS VLSI design is therefore to use simple clocking schemes, even at the expense of performance. Most automated design methodologies such as standard cell employ a single-phase, edge-triggered approach, based on
static flip-flops. But the tendency towards simpler clocking approaches is also apparent in
chapter7.fm Page 338 Friday, January 18, 2002 9:09 AM
DESIGNING SEQUENTIAL LOGIC CIRCUITS
338
Chapter 7
high-performance designs such as microprocessors. The use of latches between logic is
also very common to improve circuit performance.
7.8
Summary
This chapter has explored the subject of sequential digital circuits. The following topics
were discussed:
• The cross-coupling of two inverters creates a bistable circuit, called a flip-flop. A
third potential operation point turns out to be metastable; that is, any diversion from
this bias point causes the flip-flop to converge to one of the stable states.
• A latch is a level-sensitive memory element that samples data on one phase and
holds data on the other phase. A register (sometime also called a flip-flop) on the
other hand samples the data on the rising or falling edge. A register has three important parameter the set-up time, the hold time, and the propagation delay. These
parameters must be carefully optimized since they may account for a significant
portion of the clock period.
• Registers can be static or dynamic. A static register holds state as long as the power
supply is turned on. It is ideal for memory that is accessed infrequently (e.g., reconfiguration registers or control information). Dynamic memory is based on temporary
charge store on capacitors. The primary advantage is the reduced complexity and
higher performance/lower power. However, charge on a dynamic node leaks away
with time, and hence dynamic circuits have a minimum clock frequency.
• There are several fundamentally different approaches towards building a register.
The most common and widely used approach is the master-slave configuration
which involves cascading a positive latch and negative latch (or vice-versa).
• Registers can also be constructed using the pulse or glitch concept. An intentional
pulse (using a one shot circuit) is used to sample the input around an edge. Generally, the design of such circuits requires careful timing analysis across all process
corners. Sense-amplifier based schemes are also used to construct registers and are
to be used when high performance or low signal swing signalling is required.
• Choice of clocking style is an important consideration. Two phase design can result
in race problems. Circuit techniques such as C2MOS can be used to eliminate race
conditions in two-phase clocking. Another option is to use true single phase clocking. However, the rise time of clocks must be carefully optimized to eliminate races.
• The combination of dynamic logic with dynamic latches can produce extremely fast
computational structures. An example of such an approach, the NORA logic style, is
very effective in pipelined datapaths.
• Monostable structures have only one stable state. They are useful as pulse generators.
• Astable multivibrators, or oscillators, possess no stable state. The ring oscillator is
the best-known example of a circuit of this class.
chapter7.fm Page 339 Friday, January 18, 2002 9:09 AM
Section 7.9
To Probe Further
339
• Schmitt triggers display hysteresis in their dc characteristic and fast transitions in
their transient response. They are mainly used to suppress noise.
7.9
To Probe Further
The basic concepts of sequential gates can be found in many logic design textbooks (e.g.,
[Mano82] and [Hill74]). The design of sequential circuits is amply documented in most of
the traditional digital circuit handbooks. [Partovi01] and [Bernstein98] provide in-depth
overviews of the issues and solutions in the design of high-performance sequential elements.
References
[Bernstein98] K. Bernstein et al., High-Speed CMOS Design Styles, Kluwer Academic Publishers,
1998.
[Dopperpuhl92] D. Dopperpuhl et al., “A 200 MHz 64-b Dual Issue CMOS Microprocessor,” IEEE
JSSC, vol. 27, no. 11, Nov. 1992, pp. 1555–1567.
[Gieseke97] B. Bieseke et al., “A 600MHz Superscalar RISC Microprocessor with Out-Of-Order
Execution,” IEEE ISSCC, pp. 176-177, Feb. 1997.
[Goncalves83] N. Goncalves and H. De Man, “NORA: a racefree dynamic CMOS technique for
pipelined logic structures,” IEEE JSSC, vol. SC-18, no. 3, June 1983, pp. 261–266.
[Hill74] F. Hill and G. Peterson, Introduction to Switching Theory and Logical Design, Wiley, 1974.
[Jeong87] D. Jeong et al., “Design of PLL-based clock generation circuits,” IEEE JSSC, vol. SC-22,
no. 2, April 1987, pp. 255–261.
[Kozu96] S. Kozu et al., “A 100MHz 0.4W RISC Processor with 200MHz Multiply-Adder, using
Pulse-Register Technique,” IEEE ISSCC, pp. 140-141, February 1996.
[Mano82] M. Mano, Computer System Architecture, Prentice Hall, 1982.
[Montanaro96] J. Montanaro et al., “A 160-MHz, 32-b, 0.5-W CMOS RISC Microprocessor,” IEEE
JSSC, pp. 1703-1714, November 1996.
[Mutoh95] S. Mutoh et al., “1-V Power Supply High-Speed Digital Circuit Technology with Multithreshold-Voltage CMOS,” IEEE Journal of Solid State Circuits, pp. 847-854, August 1995.
[Partovi96] H. Partovi, “Flow-Through Latch and Edge-Triggered Flip Flop Hybrid Elements,”
IEEE ISSCC, pp. 138-139, February 1996.
[Partovi01] H. Partovi, “Clocked Storage Elements,” in Design of High-Performance Microprocessor Circuits, Chandakasan et al, Ed., Chapter 11, pp. 207-233, 2001.
[Schmitt38] O. H. Schmitt, “A Thermionic Trigger,” Journal of Scientific Instruments, vol. 15, January 1938, pp. 24–26.
[Suzuki73] Y. Suzuki, K. Odagawa, and T. Abe, “Clocked CMOS calculator circuitry,” IEEE Journal of Solid State Circuits, vol. SC-8, December 1973, pp. 462–469.
[Yuan89] J. Yuan and Svensson C., “High-Speed CMOS Circuit Technique,” IEEE JSSC, vol. 24,
no. 1, February 1989, pp. 62–70.
chapter9.fm Page 406 Friday, April 5, 2002 4:15 PM
CHAPTER
9
COPING WITH INTERCONNECT
Driving large capacitors
n
Dealing with transmision line effects in wires
n
Signal integrity in the presence of interconnect parasitics
n
Noise in supply networks
n
9.1
Introduction
9.2
Capacitive Parasitics
9.3
406
9.2.1
Capacitance and Reliability—Cross
Talk
9.2.2
Capacitance and Performance in
CMOS
Resistive Parasitics
9.3.1
Resistance and Reliability—Ohmic
Voltage Drop
9.3.2
Electromigration
9.3.3
Resistance and Performance—RC
Delay
9.4
9.5
Inductive Parasitics
9.4.1
Inductance and Reliability— Voltage
Drop
9.4.2
Inductance and
Performance—Transmission Line
Effects
Advanced Interconnect Techniques
9.5.1
Reduced-Swing Circuits
9.5.2
Current-Mode Transmission
Techniques
9.6
Perspective: Networks-on-a-Chip
9.7
Chapter Summary
chapter9.fm Page 407 Friday, April 5, 2002 4:15 PM
Section 9.1
9.1
Introduction
407
Introduction
In previous Chapters, we have pointed out the growing impact of interconnect parasitics
on all design metrics of digital integrated circuits. As mentioned, interconnect introduces
three types of parasitic effects—capacitive, resistive, and inductive—, all of which influence the signal integrity and degrade the performance of the circuit. While so far we have
concentrated on the modeling aspects of the wire, we now analyze how interconnect
affects the circuit operation, and we present a collection of design techniques to cope with
these effects. The discussion addresses each parasitic in sequence.
9.2
Capacitive Parasitics
9.2.1
Capacitance and Reliability—Cross Talk
An unwanted coupling from a neighboring signal wire to a network node introduces an
interference that is generally called cross talk. The resulting disturbance acts as a noise
source and can lead to hard-to-trace intermittent errors, since the injected noise depends
upon the transient value of the other signals routed in the neighborhood. In integrated circuits, this intersignal coupling can be both capacitive and inductive, as shown earlier in
Figure 1.10. Capacitive cross talk is the dominant effect at current switching speeds,
although inductive coupling forms a major concern in the design of the input-output circuitry of mixed-signal circuits.
The potential impact of capacitive crosstalk is influenced by the impedance of the
line under examination. If the line is floating, the disturbance caused by the coupling persists and may be worsened by subsequent switching on adjacent wires. If the wire is
driven, on the other hand, the signal returns to its original level.
Floating Lines
Let us consider the circuit configuration of
Figure 9.1. Line X is coupled to wire Y by a
parasitic capacitance CXY. Line Y sees a total
capacitance to ground equal to CY. Assume that
the voltage at node X experiences a step
change equal to ∆VX . This step appears on
node Y attenuated by the capacitive voltage
divider.
CXY
∆V Y = ---------------------∆V
CY + CX Y X
X
VX
CXY
Y
CY
Figure 9.1 Capacitive coupling
to a floating line.
(9.1)
Circuits that are particularly susceptive to capacitive cross talk are networks with lowswing precharged nodes, located in adjacency to full-swing wires (with ∆VX = VDD ).
Examples are dynamic memories, low-swing on-chip busses, and some dynamic logic
families.
chapter9.fm Page 408 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
408
Chapter 9
Example 9.1 Interwire Capacitance and Cross Talk
Consider the dynamic logic circuit of Figure 9.2. The storage capacitance CY of the dynamic
node Y is composed of the diffusion capacitances of the pre- and discharge transistors, the
gate capacitance of the connecting inverter, and the wire capacitance. A nonrelated signal Y is
routed as a Metal1 wire over the polysilicon gate of one of the transistors in the inverter. This
creates a parasitic capacitance CXY with respect to node Y. Suppose now that node Y is precharged to 2.5 V and that signal X undergoes a transition from 2.5 V to 0 V. The charge redistribution causes a voltage drop ∆V Y on node Y, as given by Eq. (9.1).
Assume that CX equals 6 fF. An overlap of 3× 1 µm2 between metal1 and polysilicon
results in a parasitic coupling capacitance of 0.5 fF (3 × 1 × 0.057 + 2 × 3 × 0.054), as
obtained from Table 4.2. The computation of the fringing effect in the case of overlapping
wires is complex and depends upon the relative orientation of the wires. We assumed in this
analysis that two sides of the cross section contribute. A 2.5 V transition on Y thus causes a
voltage disturbance of 0.19 V on the dynamic node (or 7.5%). Combined with other parasitic
effects, such as charge redistribution and clock feedthrough, this might lead to circuit malfunctioning.
V DD
CLK
C XY
Y
In 1
In 2
In 3
CY
PDN
X
2.5 V
0V
CLK
Figure 9.2 Cross talk in dynamic
circuits.
Driven Lines
If the line Y is driven with a resistance RY, a step on line X results in a transient on line Y
(Figure 9.3a). The transient decays with a time constant τXY = R Y(CXY +CY ). The actual
impact on the “victim line” is a strong function of the rise (fall) time of the interfering signal. If the rise time is comparable or larger than the time constant, the peak value of disturbance is diminished. This is illustrated by the simulated waveforms of b. Obviously,
keeping the driving impedance of a wire—and hence τXY —low goes a long way towards
reducing the impact of capacitive cross talk. The keeper transistor, added to a dynamic
gate or precharged wire, is an excellent example of how impedance reduction helps to
control noise.
In summary, the impact of cross talk on the signal integrity of driven nodes is rather
limited. The resulting glitches may cause malfunctioning of connecting sequential ele-
chapter9.fm Page 409 Friday, April 5, 2002 4:15 PM
Section 9.2
Capacitive Parasitics
409
X
RY
VX
0.5
CXY
t r = 5 psec
0.45
Y
0.4
CY
tr = 100 psec
0.35
tr = 200 psec
V (Volt)
0.3
(a) Driven line Y with interferer X
0.25
tr = 500 psec
0.2
0.15
0.1
0.05
0
Figure 9.3 Capacitive coupling to a
driven line.
0
0.2
0.4
0.6
t(sec)
0.8
1
x 10
-9
(b) Voltage response for different rise times of V x (0 t0 2.5 V)
(Rx = 10 kΩ, C y = 20 fF, C xy = 5 fF)
ments, and should therefore be carefully monitored. However, the most important effect is
an increase in delay as is discussed in a subsequent paragraph.
Design Techniques—Dealing with Capacitive Cross Talk
Cross talk is a proportional noise source. This means that scaling the signal levels to
increase noise margins does not help since the noise sources scale in a similar way. The
only options in addressing the problem is to control the circuit geometry, or to adopt signaling conventions that are less sensitive to coupled energy. A number of ground rules can
be established (as advocated in [Dally98]).
1. It is obviously not a good idea to allow the capacitance between two signal wires to
grow too large if one wants to keep cross talk at a minimum. It is, for instance, bad
practice to have two wires on the same layer run parallel for a long distance. One is
often tempted to do just that when distributing the two clocks in a two-phase system
or when routing a bus. Wires on adjacent layers should be run perpindicular.
2. Avoid floating nodes if at all possible. Nodes sensitive to cross talk problems, such
as precharged busses, should be equiped with keeper devices to reduce the impedance.
3. Sensitive nodes should be well-separated from full-swing signals.
4. Make the rise (fall) time as large as possible, subject to timing constraints.
5. Use differential signaling in sensitive low-swing wiring networks. This turns the
cross talk signal into a common-mode noise source that does not impact the operation of the circuit.
6. If necessary, provide a shielding wire—GND or VDD —between the two signals (Figure 9.4). This effectively turns the interwire capacitance into a capacitance-toground and eliminates interference.
chapter9.fm Page 410 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
410
Chapter 9
7. The interwire capacitance between signals on different layers can be further reduced
by the addition of extra routing layers. When four or more routing layers are available, we can fall back to an approach often used in printed circuit board design.
Every signal layer is interleaved with a GND or VDD metal plane (Figure 9.4).
Shielding
wire
GND
V DD
Shielding
layer
GND
Substrate (GND)
9.2.2
Figure 9.4 Cross section of routing
layers, illustrating the use of shielding to
reduce capacitive cross talk.
Capacitance and Performance in CMOS
Cross Talk and Performance
The previous section discussed the impact of capacitive crosstalk on the signal integrity.
Even when cross talk does not result in fatal breakdown of the circuit, it still should be
monitored carefully as it also impacts the performance of the gate. The circuit schematic
of Figure 9.5 is illustrative of how capacitive cross talk may result in a data-dependent
variation of the propagation delay. Assume that the inputs to the three parallel wires X, Y,
X
Cc
Y
Cc
Z
Figure 9.5 Impact of cross talk on propagation
delay.
and Z experience simultaneous transitions. Wire Y (called the victim wire) switches in a
direction that is opposite to the transitions of its neighboring signals X and Z. The coupling
chapter9.fm Page 411 Friday, April 5, 2002 4:15 PM
Section 9.2
Capacitive Parasitics
411
capacitances experience a voltage swing that is double the signal swing, and hence represent an effective capacitive load that is twice as large as Cc—the by now well-known
Miller effect. Since the coupling capacitance represents a large fraction of the overall
capacitance in the deep-submicron dense wire structures, this increase in capacitance is
substantial, and has a major impact on the propagation delay of the circuit. Observe that
this is a worst-case scenario. If all inputs experience a simultaneous transition in the same
direction, the voltage over the coupling capacitances remains constant, resulting in a zerocontribution to the effective load capacitance. The total load capacitance CL of gate Y
hence depends upon the data activities on the neighboring signal,s and varies between the
following bounds:
C G N D ≤ CL ≤ C GND + 4C c
(9.2)
with CGND the capacitance of node Y to ground, including the diffusion and fanout capacitances. In [Sylvester98], it was established that for a 0.25 µm technology the wire delay
with noise is potentially 80% larger than the wire delay without noise (scenario of Figure
9.5; wire length = 100 µm, fanout = 2).
Complicating the analysis of this problem is the fact that the capacitance not only
depends upon the values of the surrounding wires, but also upon the exact timing of the
transitions. The simultaneity of transitions can only be detected from detailed timing simulations, making the timing verification process substantially more complex. The ensuing
explosion in verification cost caused by the unpredictably of the actual delay is hence a
source of major concern. Just assuming worst-case conditions for the capacitances—this
is, always assuming the Miller effect—leads to an overly pessimistic estimation, and overkill in the circuit design.
Design Techniques—Circuit Fabrics with Predictable Wire Delay
With cross talk making wire-delay more and more unpredictable, a designer can choose
between a number of different methodology options to address the issue, some of which are
enumerated below.
1. Evaluate and improve—After detailed extraction and simulation, the bottlenecks in
delay are identified, and the circuit is appropriately modified.
2. Constructive layout generation—Wire routing programs take into account the effects of
the adjacent wires, ensuring that the performance requirements are met.
3. Predictable structures—By using predefined, known, or conservative wiring structures,
the designer is ensured that the circuit will meet his specifications and that cross talk will
not be a show stopper.
The first approach is the one most often used. It has the disadvantage of requiring many
iterations through the complete design generation process, and hence being very slow. The second technique is appealing. The complexity of the required tool set makes it however doubtful
how much of this ambitious goal is actually achievable in a reliable (and affordable) way in the
foreseeable future. although major inroads have been made already. The last approach may be
the only one that is really workable in the short haul. Just as regular structures helped to tame
chapter9.fm Page 412 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
412
Chapter 9
the complexity of transistor layout in the early 1980’s, regular and predictable wiring topologies may be the way to address the capacitive cross talk problem. Field-programmable gate
arrays (FPGA’s), with their well-characterized interconnect grid, are an example in case. The
availability of multiple layers of metal interconnect makes this approach viable for semi-custom (and custom) design as well. The dense wire fabric [Khatri99], shown in Figure 9.6, preS
G
S
V
S
VV S
G
V
S
S
V
S
S
G
G
S
V
V
S
V
SS
Figure 9.6 Dense wire fabric (DWF) [Khatri99].
S, V, and G stand for Signal, V D D, and GND,
respectively.
sents such a solution. Minimum-width wires are prewired on a minimum pitch distance. Wires
on adjacent layers are routed orthogonally, mimimizing the cross talk. Signals on the same
layer are separated by VD D or GND shields. The wiring structure is personalized by providing
via’s at the appropriate places. The advantage of the approach is that cross talk is virtually
eliminated, and that delay variation is reduced to maximally 2%. This comes at a cost in area,
and a 5% capacitance—and hence performance and power—increase. For most designs, the
reduction in design and verification time easily compensates for this performance penalty.
Capacitive Load and Performance
The increasing values of the interconnect capacitances, especially those of the global
wires, emphasize the need for effective driver circuits that can (dis)charge capacitances
with sufficient speed. This need is further highlighted by the fact that in complex designs a
single gate often has to drive a large fan-out and hence has a large capacitive load. Typical
examples of large on-chip loads are busses, clock networks, and control wires. The latter
include, for instance, reset and set signals. These signals control the operation of a large
number of gates, so fan-out is normally high. Other examples of large fan-outs are
encountered in memories where a large number of storage cells is connected to a small set
of control and data wires. The capacitance of these nodes is easily in the multi-picofarad
range. The worst case occurs when signals go off-chip. In this case, the load consists of the
package wiring, the printed circuit board wiring, and the input capacitance of the connected ICs or components. Typical off-chip loads range from 20 to 50 pF, which is multi-
chapter9.fm Page 413 Friday, April 5, 2002 4:15 PM
Section 9.2
Capacitive Parasitics
413
ple thousand times larger than a standard on-chip load. Driving those nodes with sufficient
speed becomes one of the most crucial design problems.
The main secrets to the efficient driving of large capacitive loads was already
unveiled in Chapter 5.They boil down to two dominant concepts:
• Adequate transistor sizing is instrumental when dealing with large loads,
• Partitioning drivers into chains of gradually-increasing buffers helps to deal with
large fanout factors.
Some other important conclusions from that analysis are worth repeating for the sake of
clarity:
• When optimizing for performance, the delay of a multi-stage driver should be partitioned equally over all stages.
• If the number of stages can be freely chosen, a fanout (sizing) factor of approximately 4 per stage leads to the minimum delay for contemporary semiconductor
processes. Choosing factors that are somewhat larger do not impact the performance
that much, while yielding substantial area benefits.
In the following sections, we elaborate further on this topic. We focus especially on the
driving of very large capacitances, such as encountered when going off-chip. We also
introduce some special, but useful driver circuits.
Driving Off-Chip Capacitances—A Case Study. As established in Chapter 2, the
increase in complexity of today’s integrated circuits translates in an explosive need for
input/outputs pins. Packages with over 1000 pins have become a necessity. This puts
tough requirements on the bonding-pad design in terms of noise immunity. The simultaneous switching of a lot of pads, each driving a large capacitor, causes large transient currents and creates voltage fluctuations on the power and ground lines. This reduces the
noise margins and affects the signal integrity, as will become apparent later in this chapter.
At the same time, technology scaling reduces the internal capacitances on the chip,
while off-chip capacitances remain approximately constant—typically 10-20 pF. The
overall effective fanout factor F of an output-pin driver hence experiences a net increase
when scaling technologies. In a consistent system-design approach, we expect the off-chip
propagation delays to scale in the same way as the on-chip delays. This puts an even
tougher burden on the bonding-pad buffer design. The challenges associated with a bonding-pad driver design are illustrated with a simple case study.
Example 9.2 Output Buffer-Design
Consider the case where an on-chip minimum-size inverter has to drive an off-chip capacitor
CL of 20 pF. Ci equals approximately 2.5 fF for a standard gate in a 0.25 µm CMOS process.
This corresponds to a t p0 of approximately 30 psec. The overall effective fanout F (the ratio
between CL and Ci) equals 8000, which definitely calls for a multistage buffer design. From
Eq. (5.36) and assuming that γ = 1, we learn that seven stages result in a near-optimal design
with a scaling factor f of 3.6, and an overall propagation delay of 0.76 nsec. With a PMOS /
NMOS ratio of 1.9— the optimum ratio derived for our standard process parameters in Example 5.6—and a minimum dimension of 0.25 µm, we can derive the widths for the NMOS and
PMOS transistors in the consecutive inverter stages, as shown in Table 9.1.
chapter9.fm Page 414 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
414
Table 9.1
Chapter 9
Transistor sizes for optimally-sized cascaded buffers.
Stage
1
2
3
4
5
6
W n (µm)
0.375
1.35
4.86
W p (µm)
0.71
2.56
9.2
7
17.5
63
226.8
816.5
33.1
119.2
429.3
1545.5
This solution obviously requires some extremely large transistors with gate widths of
up to 1.5 mm! The overall size of this buffer equals several thousand minimum-size inverters,
which is quite prohibitive as a complex chip requires a large number of those drivers. This
argument clearly illustrates the enormous cost associated with attempting to achieve optimum
delay.
Trading off Performance for Area and Energy Reduction. Fortunately, it is not necessary to achieve the optimal buffer delay in most cases. Off-chip communications can often
be performed at a fraction of the on-chip clocking speeds. Relaxing the delay requirements
still allows for off-chip clock speeds in excess of 100 Mhz, while substantially reducing
the buffering requirements. This redefines the buffer design problem.
Given a maximum propagation delay time tp,max, determine the number of
buffer stages N and the required scaling factor f, such that the overall area is
minimized. This is equivalent to finding a solution that sets tp as close as possible to tp,max.
The optimization problem is now reformulated into the finding of the minimum integer
value of N that obeys the constraints of Eq. (9.3).
tp ,m a x
f = N × F1 ⁄ N
------------- ≥ ln ( F ) ----------tp 0
ln ( f )
(9.3)
This transcendental optimization problem can be solved using a small computer program
or using mathematical packages such as MATLAB [Etter93]. Figure 9.7 plots the righthand side of this equation as a function of N for some values of F. For a given value of the
overall effective fanout F, and a maximum value of the delay (tpmax/tpo), the minimum
number of buffers N is derived from inspection of the appropriate curve.
Using the total width of the transitors as a measure, we can also project the area savings of the larger scaling factor. Assuming that the area of the minimum inverter equals
Amin , and that scaling the transistors with a factor f results in a similar area increase, we
can derive the area of the driver as a function of f.
2
Adriver = ( 1 + f + f + … + f
N
N–1
)A min
f –1
F–1
= ------------- Am i n = ------------ Amin
f–1
f–1
(9.4)
In short, the area of the driver is approaximately inversely proportional to the tapering factor f. Choosing larger values of f can help to substantially reduce the area cost.
chapter9.fm Page 415 Friday, April 5, 2002 4:15 PM
Section 9.2
Capacitive Parasitics
415
10,000
F = 10,000
tp/tp 0
1000
100
F = 1000
F = 100
10
1
3
5
7
9
Number of buffer stages N
11
Figure 9.7 tp/tp 0 as a function of
the number of buffer stages for
various values of the overall
fanout F.
It is also worth reflecting briefly on the energy dissipation of the exponential buffer.
While it takes an amount of energy equal to CLVDD 2 to just switch just the load capacitance, the driver itself consumes energy as well to switch its internal capacitances (ignoring short-circuit energy). This overhead energy is approximated by the expression below,
2
E driver = ( 1 + f + f + … + f
N–1
2
)C i V DD
CL 2
2
F–1
= ------------ Ci VD D ≈ ----------V
f–1
f – 1 DD
(9.5)
This means that driving a large capacitance fast (suing the optimum taperaing factor of
3.6) takes an extra 40% of energy. For large load capacitances, this is a substantial overhead. Backing off somewhat from the optimum tapering factor can help to reduce the extra
dissipation.
Example 9.3 Output Driver Design—Revisited
Applying these results to the bonding-pad driver problem and setting tp,max to 2 nsec results in
the following solution: N = 3, f = 20, and tp = 1.8 nsec. The required transistor sizes are summarized in Table 9.2.
Table 9.2
Transistor sizes of redesigned cascaded buffer.
Stage
1
2
3
Wn (µ m )
0.375
7.5
150
Wp (µ m )
0.71
14.4
284
The overall area of this solution is approximately 7.5 times smaller than the optimum
solution, while its speed is reduced by less than a factor of 2.5. It also reduces the extra energy
dissipation per switching transition due to the buffer intrinsic capacitances to an almost negligible amount. The overall dissipation of the combined buffer and load is reduced by 24%,
chapter9.fm Page 416 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
416
Chapter 9
which corresponds to a hefty amount given the size of the load capacitor. This clearly shows
that designing a circuit for the right speed, not for the maximum speed, pays off!
Design Consideration—Implementing Wide Transistors
Even this redesigned buffer requires wide transistors. One must be careful when designing
those devices, since the large value of W translates into very long gate connections. Long polyD(rain)
S
Multiple
Contacts
D
G
S(ource)
S
polysilicon
G(ate)
(a) Small transistors in parallel
Figure 9.8
(b) Circular transistors
Approaches to implementing very wide transistors.
silicon wires tend to be highly resistive, which degrades the switching performance. This problem can be addressed in a number of ways. For instance, a wide transistor can be constructed
by connecting many smaller transistors in parallel (Figure 9.8a) or by using ring- or even spiral-shaped devices (Figure 9.8b). In each approach, the resistance of the gate is reduced with
the aid of a low-resistance metal bypass connecting the shorter polysilicon sections. An example of a pad driver designed using these techniques is shown in Figure 9.9.
Design Consideration—Designing Reliable Input/Output Pads
Design Challenge—Designing Reliable Output and Input Pads
The design of bonding pad-drivers is obviously a critical and nontrivial task that is further
complicated by noise and reliability considerations. For instance, the large transient currents resulting from the switching of the huge output capacitance can cause latchup to
occur. Multiple well and substrate contacts supplemented with guard rings help avoid the
onset of this destructive effect.
Guard rings are grounded p+ diffusions in a p-well and supply-connected n+ diffusions in an n-well that are used to collect injected minority carriers before they reach the
base of the paraistic bipolar transistors. These rings should surround the NMOS and
PMOS transistors of the final stage of the output pad driver.
The designer of an input pad faces some different challenges. The input of the first
stage of the input buffer is directly connected to external circuitry, and is hence sensitive
chapter9.fm Page 417 Friday, April 5, 2002 4:15 PM
Section 9.2
Capacitive Parasitics
417
Bonding pad
GND
In
Out
n + guard ring
In
V DD
GND
Out
Figure 9.9 Layout of final stage of bonding-pad driver. The plot on the right side is a magnification of the NMOS
transistor connected between GND and Out. See also Colorplate 13.
to any voltage excursions on the connected input pins. A human walking over a synthetic
carpet over in 80% relative humidity can accumulate a voltage potential of 1.5 kV—you
have probably experienced the sparks that jump from your hand when touching a metal
object under those circumstances. The same is true for the assembly machinery. The gate
connection of an MOS transistor has a very high input resistance (10 12 to 1013 Ω). The
voltage at which the gate oxide punctures and breaks down is about 40-100 V, and is getting smaller with reducing oxide thicknesses. A human or machine, charged up to a high
static potential, can hence easily cause a fatal breakdown of the input transistors to happen
when brought in contact with the input pin. This phenomenum called Electrostatic Discharge (ESD) has proven to be fatal to many circuits duirng manufacturing and assembly.
A combination of resistance and diode clamps are used to defray and limit this
potentially destructive voltage. A typical electrostatic protection circuit is shown in Figure 9.10a. The protection diodes D1 and D2 turn on when the voltage at node X rises below
VDD or goes below ground. The resistor R is used to limit the peak current that flows in the
diodes in the event of an unusual voltage excursion. Current process tend to use tub resistors (p-diffusion in an n-well, and n-diffusion for a p-well) to implement the resistors, and
values can be anywhere from 200Ω to 3 kΩ. The designer should be aware that the resulting RC time-constant can be a performance limiting factor in high-speed circuits. Figure
9.10b shows the layout of a typical input pad.
chapter9.fm Page 418 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
418
VDD
BUFFER
RESISTOR
D1
R
PAD
X
D2
(a)
Chapter 9
C
Figure 9.10 Input protection
Circuit (a), and layout of input
pad (b).
Diode
PAD
(b)
The task of the pad designer seems to become harder for every new technology generation. Fortunately, a number of novel packaging technologies that reduce off-chip
capacitance, are currently emerging. For instance, advanced technqiues such as ball grid
arrays and chip-on-board go a long way in helping to reducing the off-chip driving
requirements (see also Chapter 2).
Some Interesting Driver Circuits. Sofar, most of our driver circuits have been simple
inverters. Sometimes, some variants are necessary. The tri-state buffer is an example of
such. Busses are essential in most digital systems. A bus is a bundle of wires that connect
a set of sender and receiver devices such as processors, memories, disks, and input/output
devices.When one device is sending on the bus, all other sending devices should be disconnected. This can be achieved by putting the output buffers of those devices in a highimpedance state Z that effectively disconnects the gate from the output wire. Such a buffer
has three possible states—0, 1, and Z—and is therefore called a tri-state buffer.
Implementing a tri-state inverter is straightforward in CMOS. Simultaneously turning off the NMOS and PMOS transistor produces a floating output node that is disconnected from its input. Two possible implementations of a tri-state buffer are shown in
Figure 9.11. While the first one is simple, the second is more appropriate for driving large
capacitances. Having transistors in series in the output stage is to be avoided due to the
huge area overhead.
chapter9.fm Page 419 Friday, April 5, 2002 4:15 PM
Section 9.3
Resistive Parasitics
419
VD D
V DD
En
En
In
Out
Out
En
In
En
9.3
Figure 9.11 Two possible
implementations of a tri-state
buffer. En = 1 enables the
buffer.
Resistive Parasitics
In this section, we discuss the impact of wiring resistance on reliability and performance.
Before doing so, we first analyze the effects of scaling on the wiring resistance and introduce a number of approximative models for resistive wires.
9.3.1
Resistance and Reliability—Ohmic Voltage Drop
140
3.5
120
3
100
2.5
80
2
60
1.5
40
1
20
0.5
0
0
EV4 EV5 EV6 EV7 EV8
Supply Voltage (V)
S upply Current (A)
Current flowing through a resistive wire results in an ohmic voltage drop that degrades the
signal levels. This is especially important in the power distribution network, where current
levels can easily reach amperes, as illustrated in Figure 9.12 for the Compaq Alpha processor family. Consider now a 2 cm long V DD or GND wire with a current of 1mA per µm
Figure 9.12 Evolution of power-supply current and supply
voltage for different generations of the high-performance
alpha microprocessor family from Compaq. Even with the
reductions in supply voltage, a total supply current of over
100 A has to be supported for the newer generations.
width. This current is about the maximum that can be sustained by an aluminum wire due
to electromigration, which is discussed in the subsequent section. Assuming a sheet resistance of 0.05 Ω/q, the resistance of this wire (per µm width) equals 1 kΩ. A current of 1
mA/µm would result in a voltage drop of 1 V. The altered value of the voltage supply
reduces noise margins and changes the logic levels as a function of the distance from the
supply terminals. This is demonstrated by the circuit in Figure 9.13, where an inverter
placed far from the power and ground pins connects to a device closer to the supply. The
difference in logic levels caused by the IR voltage drop over the supply rails might partially turn on transistor M1. This can result in an accidental discharging of the precharged,
dynamic node X, or cause static power consumption if the connecting gate is static. In
chapter9.fm Page 420 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
420
V DD
φ pre
Chapter 9
I
R′
V D D – ∆V′
I
∆V
X
M1
∆V
Figure 9.13 Ohmic voltage
drop on the supply rails reduces
the noise margins.
R
short, the current pulses from the on-chip logic, memories and I/O pins cause voltage
drops over the power-distribution network, and are the major source for on-chip powersupply noise. Beyond causing a reliability risk, IR drops on the supply network also
impact the performance of the system. A small drop in the supplu voltage may cause a significant increase in delay.
The most obvious solution to this problem is to reduce the maximum distance
between the supply pins and the circuit supply connections. This is most easily accomplished through a structured layout of the power distribution network. A number of onchip power-distribution networks with peripheral bonding are shown in Figure 9.14. In all
(a)
(b)
(c)
Figure 9.14 On-chip power distribution networks.
(a) Single layer power grid;
(b) Dual layer grid;
(c) Dual power plane.
cases, power and ground are brought onto the chip via bonding pads located on the four
sides of the chip. Which approach to use depends upon the number of coarse metal layers
(this is, thick, high pitch topmost metal layers) one wants to allocate to power distribution.
chapter9.fm Page 421 Friday, April 5, 2002 4:15 PM
Section 9.3
Resistive Parasitics
421
In the first approach (a), power and ground are routed vertically (or horizontally) on the
same layer. Power is brought in from two sides of the chip. Local power strips are
strapped to this upper grid, and then further routed on the lower metal levels. Method (b)
uses two coarse metal layers for the power distribution, and the power is brought in from
the four sides of the die. This approach was used in the EV5 generation of the Compaq
Alpha processor [Herrick00]. The combination of power and clock distribution occupied
more than 90% of the 3rd and 4th Al layers. One further and more aggressive step to take
is to use two solid metal planes for the distribrution of V dd and GND (c). This approach
has the advantage of drastically reducing the resistance of the network. The metal planes
also act as shields between data signalling layers, hence reducing cross-talk. They also
help to reduce the on-chip inductance. Obviously, this approach is only feasible when sufficient metal layers are available.
The sizing of the power network is a non-trivial task. The power grid can be modeled as a network of resistors (wires) and current sources (logic), containing hundreds of
millions of elements. Very often, many paths exist between the power pins and the supply
connections of a chip module or gate. While in general the current follows the path of the
lowest resistance, the exact flow depends upon factors such as the current draw from
neighboring modules that share the same network. The analysis is complicated by the fact
that peak currents drawn by the connected modules are distributed over time. IR drop is a
dynamic phenomenon due primarily to simultaneous switching events such as clocks, and
bus drivers. As large drivers begin to switch, the simultaneous demand from current from
the power network stresses the grid. At the same time, a worst-case analysis adding all the
peak currents may lead to a gross overdimensioning of the wires.
The above makes it clear that computer-aided design tools are a necessary companion of the power-distribution network designer. Given the complexity of todays integrated
circuits, transistor-level analysis of the complete power-network requirements is just not
feasible. At the same time, partitioning of the problem over sub-sections might not result
in an accurate picture either. Changes to the power grid in one section tend to have a global impact. This is illustrated in Figure 9.15, which shows the simulated IR voltage drop
of a complex digital circuit. A first implementation (a) suffers from a more than acceptable drop in the upper right module of the design, because only the top portion of the
power grid feeds the large drivers at the top. The lower portions of the module are not
directly connected to the grid. Adding just one single strap to the network largely resolves
this problem, as shown in (b).
Therefore, an accurate picture of the IR risk cannot be obtained unless the entire
chip is verified as a single entity. Any tool used for this purpose must have the capacity to
analyze multi-million resistor grids. Fortunately, a number of efficient and quite accurate
power-grid analysis tools are currently available [Simplex, ]. They combine a dynamic
analyis of the current requirements of the circuit modules with a detailed modeling of the
popwer network. Tools as such are quite indispensable in todays design process.
9.3.2
Electromigration
The current density (current per unit area) in a metal wire is limited due to an effect called
electromigration. A direct current in a metal wire running over a substantial time period,
chapter9.fm Page 422 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
422
Chapter 9
Highest voltage drop
(a)
(b)
Figure 9.15 Simulated IR voltage drop in power-distribution network of two versions of a complex digital
integrated circuit. The gray-scale is used to indicate the severeness of the voltage drop. Adding an extra strap
to the upper layers of the power network (b) helps to address the large voltage trop in the upper right module in
the initial design (a).
causes a transport of the metal ions. Eventually, this causes the wire to break or to shortcircuit to another wire. This type of failure will only occur after the device has been in use
for some time. Some examples of failure caused by migration are shown in Figure 9.16.
Notice how the first photo clearly shows hillock formation in the direction of the electron
current flow.
(a) Line-open failure.
Figure 9.16
(b) Open failure in contact plug.
Electromigration-related failure modes (Courtesy of N. Cheung and A. Tao, U.C. Berkeley).
The rate of the electromigration depends upon the temperature, the crystal structure,
and the average current density. The latter is the only factor that can be effectively controlled by the circuit designer. Keeping the current below 0.5 to 1 mA/µm normally prevents migration. This parameter can be used to determine the minimal wire width of the
power and ground network. Signal wires normally carry an ac-current and are less susceptible to migration. The bidirectional flow of the electrons tends to anneal any damage done
chapter9.fm Page 423 Friday, April 5, 2002 4:15 PM
Section 9.3
Resistive Parasitics
423
to the crystal structure. Most companies impose a number of strict wire-sizing guidelines
on their designers, based on measurements and past experience. Research results have
shown that many of these rules tend to be overly conservative [Tao94].
Design Rule
Electromigration effects are proportional to the average current flow through the wire, while IR
voltage drops are a function of the peak current.
At the technology level, a number of precautions can be taken to reduce the migration
risk. One option is to add alloying elements (such as Cu or Tu) to the aluminum to prevent
the movement of the Al ions. Another approach is to control the granularity of the ions. The
introduction of new interconnect materials is a big help as well. For instance, the use of
Copper interconnect increases the expected lifetime of a wire with a factor of 100 over Al.
9.3.3
Resistance and Performance—RC Delay
In Chapter 4, we established that the delay of a wire grows quadratically with its length.
Doubling the length of a wire increases its delay by a factor of four! The signal delay of
long wires therefore tends to be dominated by the RC effect. This is becoming an ever
larger problem in modern technologies, which feature an increasing average length of the
global wires (Figure 4.27)—at the same time that the average delay of the individual gates
is going down. This leads to the rather bizar situation that it may take multiple clock
cycles to get a signal from one side of a chip to its opposite end [Dally-DAC]. Providing
accurate synchronization and correct operation becomes a major challenge under these circumstances. In this section, we discuss a number of design techniques that may help to
cope with the delay imposed by the resistance of a wire.
Better Interconnect Materials
A first option for reducing RC delays is to use better interconnect materials when they are
available and appropriate. The introduction of silicides and Copper have helped to reduce
the resistance of polysilicon (and diffused) and metal wires, respectively, while the adoption of dielectric materials with a lower permittivity lowers the capacitance. Both Copper
and low-permittivity dielectrics have become common in advanced CMOS technologies
(starting from the 0.18 µm technology generation). Yet, the designer should be aware that
these new materials only provide a temporary respite of one or two generations, and do not
solve the fundamental problem of the delay of long wires. Innovative design techniques
are often the only way of coping with the latter.
chapter9.fm Page 424 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
424
Chapter 9
Example 9.4 Impact of Advanced Interconnect Materials
Copper offers a resistivity that is 1.6 times lower than that of Aluminum (Table 4.4) from a
pure material perspective. Cladding and other manufacturing artifacts may increase the effective resistivity of on-chip Cu wires to approximately 2.2 10-8 Ω-m.
Sometimes, it is hard to avoid the use of long polysilicon wires. A good example of
such circumstance are the address lines in memories, which must connect to a large number of transistor gates. Keeping the wires in polysilicon increases the memory density substantially by avoiding the overhead of the extra metal contacts. The polysilicon-only
option unfortunately leads to an excessive propagation delay. One possible solution is to
drive the word line from both ends, as shown in Figure 9.17a. This effectively reduces the
worst-case delay by a factor of four. Another option is to provide an extra metal wire,
called a bypass, which runs parallel to the polysilicon one, and connects to it every k cells
(Figure 9.17b). The delay is now dominated by the much shorter polysilicon segments
between the contacts. Providing contacts only every k cells helps to preserve the implementation density.
Driver
WL
Polysilicon word line
Metal word line
(a) Driving the word line from both sides
Metal bypass
WL
K cells
Polysilicon word line
(b) Using a metal bypass
Figure 9.17
Approaches to reduce the word-line delay.
Better Interconnect Strategies
With the length of the wire being a prime factor in both the delay and the energy consumption of an interconnect wire, any approach that helps to reduce the wire length is bound to
have an essential impact. It was pointed out earlier that the addition of interconnect layers
tends to reduce the average wire length, as routing congestion is reduced and interconnections can pretty much follow a direct path between source and destination. Yet, the
“Mahattan-style” wiring approach that is typical in todays routing tools brings with it a
substantial amount of overhead that is often overlooked. In the Manhattan-style routing,
interconnections are routed first along one of two preferred directions, followed by a connection in the other direction (Figure 9.18a). It seems obvious that routing along the diagonal direction would yield a sizable reduction in wirelength—of up to 29% in the best
case. Ironically, 45° lines were very popolar in the early days of integrated circuits
chapter9.fm Page 425 Friday, April 5, 2002 4:15 PM
Section 9.3
Resistive Parasitics
425
designs, but got of out of vogue because of complexity issues, impact on tools, and maskmaking concerns. Recently, it has been demonstrated that these concerns can be addressed
adequately, and that 45° lines are perfectly feasible [Simplex01]. The impact on wiring is
quite tangible: a reduction of 20% in wirelength! This in turn results in higher performance, lower power dissipation, and smaller chip area. The density of wiring structures
that go beyond pure Manhattan directions, is demonstrated clearly in a sample layout,
shown in Figure 9.18b.
di
a
go
na
l
destination
y
source
x
Manhattan
(a)
Figure 9.18 Manhattan versus diagonal routing.
(a) Manhattan routing uses preferential routing along
orthogonal axis, while diagonal routing allows for 45° lines.
(b) example of layout using 45° lines.
(b)
Introducing Repeaters
The most popular design approach to reducing the propagation delay of long wires is to
introduce intermediate buffers, also called repeaters, in the interconnect line (Figure
9.19). Making an interconnect line m times shorter reduces its propagation delay quadratically, and is sufficient to offset the extra delay of the repeaters when the wire is sufficiently long. Assuming that the repeaters have a fixed delay tpbuf , we can derive the delay
of the partitioned wire.
2
tp = 0.38 rc -L
--- m + mt pbuf
m
(9.6)
tpbuf
R/m
R/m
R/m
R/m
V out
V in
C/m
Figure 9.19
C/m
C/m
Reducing RC interconnect delay by introducing repeaters.
C/m
chapter9.fm Page 426 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
426
Chapter 9
The optimal number of buffers that minimes the overall delay can be found by setting
∂tp / ∂m = 0.
0.38 rc
m opt = L ---------------- =
tpbuf
tpwire ( u n b u f f e r e d)
------------------------------------t pbuf
(9.7)
yielding a minimum delay of
tp , opt = 2 tp w i r e(u n b u f f e r e d) t pbuf
(9.8)
and is obtained when the delay of the individual wire segments is made equal to that of a
repeater. Observe also the equivalence between this design problem and the chain of transmission gates, as discussed in Example 6.11.
Example 9.5 Reducing the Wire Delay through Repeaters
In Example 4.8, we derived the propagation delay of a 10 cm long, 1 µm wide Al1 wire to be
31.4 nsec. Eq. (9.7) indicates that a partitioning of the wire into 18 sections would minimize
its delay, assuming a fixed tpbuf of 0.1 nsec. This results in an overall delay time of 3.5 nsec,
an important improvement. Similarly, the delays of equal-length Polysilicon and Al5 wires
would be reduced to 212 nsec (from 112 µsec) and 1.3 nsec (from 4.2 nsec) by introducing
1058 and 6 stages, respectively.
The above analysis is simplified and optimistic in the sense that tpbuf is a function of
the load capacitance. Sizing the repeaters is needed to reduce the delay. A more precise
expression of the delay of the interconnect chain is obtained by modeling the repeater as
an RC network, and by using the Ellmore delay approach. Assuming that R d and Cd are the
resistance and capacitance of a minimum-sized repeater, and s is the sizing factor, this
leads to the following expression:
R cL
rL
L 2
t p = m 0.69-----d ------ + sC d + 0.69 ------ ( sCd ) + 0.38 rc --
s m
m
m
(9.9)
By setting ∂tp / ∂m and ∂tp /∂s to 0, optimal values for m, s and tpmin are obtained.
0.38rc
m opt = L ----------------------- =
0.69R d C d
s opt =
tpwire ( u n b u f f e r e d)
------------------------------------tp b u f, m i n
Rd c
--------rCd
(9.10)
t p,m i n = 2.4 L R d C d rc
Eq. (9.10) clearly demonstrates how the insertion of repeaters linearizes the delay of a
wire. Also, observe that for a given technology and a given interconnect layer, there exists
aan optimal length of the wire segments between repeaters. We call this the critical length
Lcrit.
chapter9.fm Page 427 Friday, April 5, 2002 4:15 PM
Section 9.3
Resistive Parasitics
427
L
L c r i t = ---------- =
m opt
0.69R d C d
----------------------0.38 rc
(9.11)
It can be derived that the delay of a segment of critical length always equals 3.23Rd Cd, and
is independent of the routing layer. Inserting repeaters to reduce the delay of a wire only
makes sense when the wire is at least two times longer than the critical length.
Example 9.6 Minimizing the Wire Delay (Revised)
In Chapter 5 (Example 5.5), we determined the intinsic delay of a minimum-sized inverter in
our 0.25 µm CMOS process to be 32.5 psec with (average) values of Rd and Cd of 7.8 kΩ and
6 fF, respectively. For an Al1 wire (c = 110 aF/µm; r = 0.075 Ω/µm), this yields an optimum
repeater sizing factor sopt = 43. Inserting 31 of these sized-up inverters, sets the minimum
delay of the 10 cm wire of Example 9.5 to a more realistic 4.7 nsec. This is in contrast to just
inserting 31 minimum-sized repeaters, which would actually increase the delay to 61 nsec due
to the poor driving capability of the repeater.
The critical length for Al1 evaluates to 3.2 mm, while it equals 54 µm and 8.8 mm for
Polysilicon and Al5, respectively.
Repeater insertion has proven such an efficient and essential tool in combatting long wire
delays that modern design automation tools perform this task automatically [REFERENCE].
Optimizing the Interconnect Architecture
Even with buffer insertion, the delay of a resistive wire cannot be reduced below the minimum dictated by Eq. (9.8). Long wires hence often exhibit a delay that is longer than the
clock period of the design. For instance, the 10 cm long Al1 wire of Example 9.6 comes
with a minimum delay of 4.7 nsec, even after optimal buffer insertion and sizing, while the
0.25 µm CMOS process featured in this text can sustain clock speeds in excess of 1 GHz
(this is, clock periods below 1 nsec). The wire delay all-by-itself hence becomes the limiting factor on the performance achievable by the integrated circuit. The only way to
address this bottleneck is to tackle it at the system architecture-level.
Wire pipelining is a popular performance-improvement technique in this category.
The concept of pipelining was introduced in Chapter 7 as a means of improving the
throughput performance of logic modules with long critical paths. A similar approach can
be used to increase the throughput of a wire, as is illustrated in Figure 9.20. The wire is
partitioned in k segments by inserting registers or latches. While this does not reduce the
delay through the wire segment—it takes k clock cycles for a signal to proceed through the
wire—, it helps to increase its throughput, as the wire is handling k signals simultaneously
at any point in time. The delay of the individual wire segments can further be optimized by
repeater insertion, and should be below a single clock period.
This is only one example of the many techniques that the chip architect has at her
disposition to deal with the wire delay problem. The most important message that emerges
from this discussion is that wires have to be considered early on in the design process, and
can no longer be treated as an afterthought as was most often the case in the past.
chapter9.fm Page 428 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
428
R/k
V in
R
R
C/k
CLK
CLK
Figure 9.20
9.4
R/k
R/k
R
C/k
CLK
R/k
V out
R
C/k
Chapter 9
C/k
CLK
Wire pipelining improves the throughput of a wire.
Inductive Parasitics
Besides having a parasitic resistance and capacitance, interconnect wires also exhibit an
inductive parasitic. An important source of parasitic inductance is introduced by the bonding wires and chip packages. Even for intermediate-speed CMOS designs, the current
through the input-output connections can experience fast transitions that cause voltage
drops as well as ringing and overshooting, phenomena not found in RC circuits. At higher
switching speeds, wave propagation and transmission line effects can come into the picture. Both effects are analyzed in this section. First, we discuss the source of these inductive parasitics and their quantitative values.
di
Inductance and Reliability— L ----- Voltage Drop
dt
9.4.1
During each switching action, a transient current is sourced from (or sunk into) the supply
rails to charge (or discharge) the circuit capacitances, as modeled in Figure 9.21. Both V DD
and VSS connections are routed to the external supplies through bonding wires and package
pins and possess a nonignorable series inductance. Hence, a change in the transient current
creates a voltage difference between the external and internal (VDD ’, GND’) supply voltages. This situation is especially severe at the output pads, where the driving of the large
external capacitances generates large current surges. The deviations on the internal supply
voltages affect the logic levels and result in reduced noise margins.
V DD
i(t)
L
V’DD
V in
V out
CL
GND’
L
Figure 9.21 Inductive coupling between external
and internal supply voltages.
chapter9.fm Page 429 Friday, April 5, 2002 4:15 PM
Section 9.4
Inductive Parasitics
429
Example 9.7 Noise Induced by Inductive Bonding Wires and Package Pins
Assume that the circuit in Figure 9.21 is the last stage of an output pad driver, driving a load
capacitance of 10 pF over a voltage swing of 2.5 V. The inverter has been dimensioned so that
the 10–90% rise and fall times of the output signal (tr , t f) equal 1 nsec. Since the power and
ground connections are connected to the external supplies through the supply pins, both connections have a series inductance L. For a traditional throughole packaging approach, an
inductance of around 2.5 nH is typical. To simplify the analysis, assume first that the inverter
acts as a current source with a constant current (dis)charging the load capacitance. A (average) current of 20 mA is required to achieve the 1 nsec output rise and fall times.
Iavg = (10 pF × (0.9 − 0.1) × 2.5 V) / 1 nsec = 20 mA
This scenario occurs where the the buffer is driven by a steep step-function at its input.
The left side of Figure 9.22 plots the simulated evolution of output voltage, inductor current,
and inductor voltage over time for t f = 50 psec. The abrupt current change causes a steep voltage spike of up to 0.95 V over the inductor. In fact, the voltage drop would have been larger,
if the drop itself did not slow down the transients and reduce the demand for current through
positive feedback. Nevertheless, a supply voltage with that much variation is unacceptable.
In reality, the charging current is rarely a constant. A better approximation assumes
that the current rises linearly to a maximum after which it drops back to zero, again in a linear
fashion. The current distribution over time models as a triangle. This situation occurs when
the input signal to the buffer displays slow rise/fall times. Under this model, the (estimated)
voltage drop over the inductor equals
v L = L di L /dt = (2.5 nH × 40 mA) / ( (1.25/2) × 1 nsec) = 133 mV.
The peak current of (approximately) 40 mA results from the fact that the total delivered
charge—or the integrated area under IL—is fixed, which means that the peak of the triangular
current distribution is double the value of the rectangular one. The denominator factor estimates the time it takes to go from 0 to peak current. Simulated results of this scenario are
shown on the right side of Figure 9.22 for tf = 1 nsec. It can be observed that the current distribution indeed becomes triangular for this slow input slope. The simulated voltage drop over
the inductor is reduced to xxx mV. This indicates that avoiding fast-changing signals at the
inputs of the drivers for large capacitirs goes a long way in reducing the Ldi/dt effects.
In an actual circuit, a single supply pin serves a large number of gates or output drivers. A simultaneous switching of those drivers causes even worse current transients and
voltage drops. As a result, the internal supply voltages deviate in a substantial way from
the external ones. For instance, the simultaneous switching of the 16 output drivers of an
output bus would cause a voltage drop of at least 1.1 V if the supply connections of the
buffers were connected to the same pin on the package.
Improvements in packaging technologies are leading to ever-increasing numbers of
pins per package. Packages with up to 1000 pins are currently available. Simultaneous
switching of a substantial number of those pins results in huge spikes on the supply rails
that are bound to disturb the operation of the internal circuits as well as other external
components connected to the same supplies.
chapter9.fm Page 430 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
430
2.5
2.5
2
2
without
1.5
V out (V)
Chapter 9
1
1.5
1
with inductors
0.5
0.5
0
0
0
0.5
1
1.5
2
0
0.5
1
1.5
-9
without inductors
0.04
2
-9
x 10
x 10
0.04
with inductors
i L (A)
decoupled
0.02
0
0.02
0
0.5
1
1.5
2
0
0
0.5
1
1.5
-9
x 10
1
2
-9
x 10
1
with inductors
0.5
VL (V)
0.5
decoupled
0
0
0
0.5
1
time (nsec)
1.5
2
-9
x 10
(a) input rise/fall time: 50 psec
0
0.5
1
1.5
time (nsec)
2
-9
x 10
(b) input rise/fall time: 800 psec
Figure 9.22 Simulated signal waveforms for output driver connected to bonding pads for input
rise/fall times of 50 psec (a) and 800 psec (b), respectively. The waveforms in (a) show the results
when (1) no inductors are present in the power distribution network (ideal case); (b) in the presence
of inductors; and (c) with added decoupling capcitance of 200 pF.
Design Techniques
A number of approaches are available to the designer to address the L(di/dt) problem.
1. Separate power pins for I/O pads and chip core—Since the I/O drivers require the
largest switching currents, they also cause the largest current changes. It is wise to isolate the center of the chip, where most of the logic action occurs, from the drivers by providing different power and ground pins.
2. Multiple power and ground pins—In order to reduce the di/dt per supply pin, we can
restrict the number of I/O drivers connected to a single supply pin. Typical numbers are
five to ten drivers per supply pin. Be aware that this number depends heavily upon the
switching characteristics of the drivers such as the number of simultaneously switching
gates and the rise and fall times.
chapter9.fm Page 431 Friday, April 5, 2002 4:15 PM
Section 9.4
Inductive Parasitics
431
3. Careful selection of the positions of the power and ground pins on the package—The inductance of pins located at the corners of the package is substantially higher
(Figure 9.23).
Bonding wire
Chip
L
Mounting
cavity
L′
Lead
frame
Pin
Figure 9.23 The inductance of a
bonding-wire/pin combination
depends upon the pin position.
4. Increase the rise and fall times of the off-chip signals to the maximum extent allowable. and distributed all over the chip, especially under the data busses. The example
above demonstrated that output drivers with over-designed rise and fall times are not
only expensive in terms of area, but also might affect the circuit operation and reliability.
We concluded in Section 9.2.2 that the better driver in terms of area is the one that
achieves a specified delay, not the one with the fastest delay. When noise is considered,
the best driver is the one that achieves a specified delay with the maximum allowable
rise and fall times at the output.
Problem 9.1
Design of Output Driver with Reduced Rise/Fall Times
Given a cascaded output driver designed for a given delay that produces excessive noise on
the supply lines, define the best approach to address the noise problem: (a) Scale down all
stages of the buffer; (b) Scale down the last stage only; (c) Scale down all stages except the
last one.
5. Use advanced packaging technologies such as surface-mount or hybrids that come
with a substantially reduced capacitance and inductance per pin. For instance, we can see
from Table 2.2 that the bonding inductance of a chip mounted in flip-chip style on a substrate using the solder-bump techniques is reduced to 0.1nH, which is 50 to 100 times
smaller than for standard packages.
6. Adding decoupling capacitances on the board— These capacitances, which should be
added for every supply pin, act as local supplies and stabilize the supply voltage seen by
the chip. They separate the bonding-wire inductance from the inductance of the board
interconnect (Figure 9.24). The bypass capacitor, combined with the inductance, actually
acts as a low-pass network that filters away the high-frequency components of the transient voltage spikes on the supply lines. 1
chapter9.fm Page 432 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
432
+
SUPPLY
Board
wiring
Chapter 9
Bonding
wire
Cd
CHIP
–
Decoupling
capacitor
Figure 9.24
inductance.
Decoupling capacitors isolate the board inductance from the bonding wire and pin
Example 9.8 Impact of Decoupling Capacitances
A decoupling capacitance of 200 pF was added between the supply connections of the buffer
circuit examined in Example 9.7. Its impact is shown in the simulations of Figure 9.22. For an
input signal rise time of 50 psec, the spike on the supply rail is reduced from 0.95 — without
decoupling capacitance — to approximately 70 mV. The waveforms also demonstrate how
the current for charging the output capacitance is drawn from the decoupling capacitor initially. Later in the transition, current is gradually being drawn from the supply network
through the bonding-wire inductors.
7. Adding decoupling capacitances on the chip— In high-performance circuits with high
switching speeds and steep signal transitions, it is becoming common practice to integrate decoupling capacitances on the chip, which ensures cleaner supply voltages. Onchip bypass capacitors reduce the peak current demand to the average value. To limit the
voltage ripple to 0.25 V, a capacitance of around 12.5 nF must be provided for every 50
Kgate module in a 0.25 µm CMOS process [Dally98]. This capacitance is typically
implemented using the thin gate oxide. A thin-oxide capacitor is essentially a MOS transistor with its drain and source tied together. Diffusion capacitors can be used for that
purpose as well.
Example 9.9 On-Chip Decoupling Capacitances in Compaq’s Alpha Processor Family
[Herrick00]
The Alpha processor family, mentioned earlier in this chapter, has been at the leading edge in
high-performance microprocessors for the last decade. Pushing the clock speed to the extreme
seriously challenges the power-distribution network. The Alpha processors are hence at fore1
A word of caution. The combination of inductor-capacitance might act as an underdamped resonator,
making the noise problem actually worse. A careful insertion of damping resistance is often required.
chapter9.fm Page 433 Friday, April 5, 2002 4:15 PM
Section 9.4
Inductive Parasitics
433
front when it comes to on-chip decoupling capacitance. Table 9.3 enumerates some characteristics of consecutive processors in the family.
Table 9.3 On-chip decoupling capacitances in Alpha Processor family.
Processor
Technology
Clock Frequency
Total Switching
Capacitance
On-chip Decoupling
Capacitance
EV4
0.75 µm CMOS
200 MHz
12.5 nF
128 nF
EV5
0.5 µm CMOS
350 MHz
13.9 nF
160 nF
EV6
0.35 µm CMOS
575 MHz
34 nF
320 nF
Given a gate capacitance of 4 fF/µm2 (t ox = 9.0 nm), the 320 nF decoupling capacitance
of the EV6 requires 80 mm 2 of die area, which is 20% of the total chip. To minimize the
impact, the capacitance was placed under the major busses. Even with this large amount of
real estate dedicated to decoupling, the designers were runing out of capacitance, and had to
resort to some innovative techniques to provide more near-chip decoupling. The problem was
solved by wirebonding a 2 µF, 2 cm 2 capacitor to the chip, and connecting the power grid to
the capacitance through 160 Vdd/GND wirebond pairs. A diagram of the Wirebond Attached
Chip Capacitor (WACC) approach is shown in Figure 9.25. This example serves as a clear
illustration of the problems that power-grid designers are facing in the high-performance
arena.
320 V dd/GND bond wires connect WACC with chip
WACC
Microprocessor
587-pin IPGA package
Figure 9.25 The Wirebond-attached Chip capacitor (WACC) approach provides extra decoupling capaciatnce
close to the chip for the Compaq EV6 microprocessor [Herrick00]. Thr microprocessor is connected to the
outside world via 320 signal pins and 198 supply/ground pins.
Finally, be aware that the mutual inductance between neighboring wires also introduces cross talk. This effect is not yet a major concern in CMOS but definitely is emerging
as an issue at the highest switching speeds ([Johnson93]).
9.4.2
Inductance and Performance—Transmission Line Effects
When an interconnection wire becomes sufficiently long or when the circuits become sufficiently fast, the inductance of the wire starts to dominate the delay behavior, and transmission line effects must be considered. This is more precisely the case when the rise and
fall times of the signal become comparable to the time of flight of the signal waveform
chapter9.fm Page 434 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
434
Chapter 9
across the line as determined by the speed of light. Until recently, this was only the case
for the fastest digital designs implemented on a board level, or in exotic technologies such
as GaAs and SiGe. As advancing technology increases line lenghts and switching speeds,
this situation is gradually becoming common in fastest CMOS circuits as well, and transmission-line effects are bound to become a concern of the CMOS designer as well.
In this section, we discuss some techniques to minimize or mitigate the impact of
the transmission line behavior. A first and foremost technique is to use approriate termination. Termination is however only effective if the current-return path is well-behaved.
Shielding of wires that are prone to transmission line effects will prove to be a necessity.
Termination
In our discussion of transmission lines in Chapter 5, it became apparent that appropriate
termination is the most effective way of minimizing the delay. Matching the load impedance to the characteristic impedance of the line results in the fastest response. This leads to
the following design rule:
To avoid the negative effects of transmission-line behavior such as ringing or
slow propagation delays, the line should be terminated, either at the source
(series termination), or at the destination (parallel termination) with a resistance matched to its characteristic impedance Z0 .
Z0
Z0
ZL
(a)
ZS
Z0
Z0
Figure 9.26 Matched termination scenarios
for wires behaving as transmission lines: (a)
series termination at the source; (b) parallel
termination at the destimation.
(b)
The two scenarios — series and parallel termination — are depicted in Figure 9.26. Series
termination requires that the impedance of the signal source is matched to the connecting
wire. This approach is appropriate for many CMOS designs, where the destination load is
purely capacitive. The impedance of the driver inverter can be matched to the line by careful transistor sizing. To drive a 50-Ω line, for example, requires a 53-µm-long NFET and a
135-µm-long PFET (in our 0.25 µm CMOS technology) to give a nominal output impedance of 50 Ω.
It is important that the impedance of the driver is closely matched to the line, typically to within 10% or better, if excessive reflections of travelling waves are to be
avoided. Unfortunately, the on-resistance of a FET may vary by 100% across process,
voltage and temperature variations. This can be compensated for by making the resistance
chapter9.fm Page 435 Friday, April 5, 2002 4:15 PM
Section 9.4
Inductive Parasitics
435
In
VDD
Z0
s0
s2
s1
ZL
sn
GND
c1
c2
cn
Figure 9.27 Tunable segmented driver providing matched series-termination to a transmission line load.
of the driver transistors electrically tunable (Figure 9.27). Each of the driver transistors is
replaced by a segmented driver, with the segments being switched in and out by control
lines c1 to cn , to match the driver impedance as close as possible to the line impedance.
Each of the segments has a different resistance, shaped by the shape factors si (typically
ratioed with factors of 2). A fixed element (s0 ) is added in parallel with the adjustable
ones, so that the range of adjustment is limited and a more precise adjustment can be made
with less bits. The control lines are usually driven by a feedback control circuit that compares an on-chip reference driver transistor to a fixed external reference transistor
[Dally98].
Similar considerations are valid when the termination is provided at the destination
end, called parallel termination. Be aware that this approach results in a standby current,
and that keeping this current flowing continuously might result in unacceptable power dissipation. Parallel termination is very popular for high-speed inter-chip, board-level interconnections, where the termination is often implemented by inserting a (grounded)
resistor next to the input pin (of the package) at the end of the wire. This off-chip termination does not take into account the package parasitics and the internal circuitry, and may
introduce unacceptably large reflections on the signal line. A more effective approach is to
include the terminating resistor inside the package after the package parasitics.
Generally, CMOS fabrication does not provide us with means to make precise, temperature-insensitive resistors. Usually, it is necessary to use interconnect materials or
FETs as resistors. Because these resistors are temperature, supply-voltage, and processdependent, tuning is necessary (either statically or continuously). Digital trimming such as
proposed earlier in this section can be used to accomplish that goal. Another issue when
using MOSFETs as resistors is ensuring that the device exhibits a linear behavior over the
operation region of interest. Since PMOS transistors typically display a larger region of
linear operation than their NMOS counterparts, they are the preferred way of implementing a terminating resistance. Assume that the triode-connected PMOS transistor of Figure
9.28a is used as a 50-Ω matched termination, connected to V DD. From simulations (Figure
9.28d), we observe that the resistance is fairly constant for small values of VR, but
increases rapidly once the transistor staurates. We can extend the linear region by increasing the bias voltage of the PMOS transistor (Figure 9.28b). This however requires an extra
supply voltage, which is not practical in most situations. A better approach is to add a
diode-connected NMOS transistor in parallel with the PMOS device (Figure 9.28c). The
chapter9.fm Page 436 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
436
Chapter 9
combination of the two devices gives a near-constant resistance over the complete voltage
range (as we have already observed in Chapter 6 when discussing transmission gates).
Many other clever schemes have been devised, but they are out the scope of this textbook.
We refer the reader to [Dally98] for a more detailed perspective.
Vdd
2
Normalized Resistance (Ω)
Mr
Out
(a)
V dd
V dd
NMOS only
1.9
1.8
1.7
PMOS only
1.6
1.5
1.4
1.3
NMOS-PMOS
1.2
PMOS with -1V bias
1.1
1
0
Mr p Mr n
Mr
(b)
Out
(c)
1
1.5
V R (Volt)
V bb
Out
0.5
2
2.5
(d)
Figure 9.28 Parallel termination of transmission
line using transistors as resistors: (a) grounded
PMOS; PMOS with negative gate bias; (c) PMOSNMOS combination; (d) Simulation.
Shielding
A transmission-line is in essence a four-port network. While we focus mostly on the signal
path, the signal-return path should not be ignored. Kirchoff’s law tells us that, when we
inject a current i into a signal conductor, a net current of -i must flow in the return. The
characteristics of the transmission line (such as its characteristic impedance) are a strong
function of the signal return. Hence, if we want to control the behavior of a wire behaving
as a transmission line, we should carefully plan and manage how the return current flows.
A good example of a well-defined transmission line is the coaxial cable, where the signal
wire is surrounded by a cylindrical ground plane. To accomplish similar effects on a board
or on a chip, designers often surround the signal wire with ground (supply) planes and
shielding wires. While expensive in real-estate, adding shielding makes the behavior and
the delay of an interconnection a lot more predictable. Yet even with these precautions,
powerful extraction and simulation tools will be needed in the future for the high-performance circuit designer.
Example 9.10
Design of an Output Driver—Revisited
As a conclusion to this section, we simulate an output driver that includes the majority of the
parasitic effects introduced in this chapter. The schematics of the driver are shown in Figure
9.29a. The inductance of the power, ground, and signal pins (estimated at 2.5 nH), as well as
the transmission line behavior of the board have been included (assuming a wire length of
15cm, which is a typical for board traces). The driver is initially designed to produce rise and
fall times of 0.33 nsec for a total load capacitance of 10pF. Producing the required average
current of 60 mA requires transistor widths of 120 µm and 275 µm for the NMOS and PMOS
chapter9.fm Page 437 Friday, April 5, 2002 4:15 PM
Section 9.4
Inductive Parasitics
437
transistors in the final stage of the driver. The first graph of Figure 9.29b shows the simulated
waveforms for this configuration. Severe ringing is observed. It is quite obvious that the
driver resistance is underdamped, hence the large overshoots and the large settling time.
The circuit was redesigned to eliminate some of these effects. First of all, the sizes of
the driver transistsors were reduced so that their impedances match the characteristic impedance of the transmission line (to 65 µm and 155 µm for NMOS and PMOS, respectively). A
decoupling capacitance of 200 pF was added to the supplies of the drivers. Finally, the inputprotection diodes of the fan-out device were added to the model to create a more realistic per-
chapter9.fm Page 438 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
438
Chapter 9
spective. The simulation shows that these modifications are quite effective, giving a circuit
that is both better behaved and faster..
V DD
Clamping
Diodes
L = 2.5 nH
V DD
120
L = 2.5 nH
V in
Z0 = 50 Ω
Vs
C L = 5 pF
275
Vd
CL
L = 2.5 nH
(a) Output driver schematic.
4
Vd
V in
Vout (V)
3
Vs
2
1
0
-1
0
1
2
3
4
5
6
7
8
x 10
Initial design
-9
4
(V)
2
Vs
1
V
out
V in
Vd
3
0
-1
0
1
2
3
4
5
6
time (sec)
7
8
x 10
-9
Revised design with matched driver impedance
(b) Transient simulations
Figure 9.29
9.5
Simulation of output driver for various terminations.
Advanced Interconnect Techniques
In previous sections, we have discussed a number of techniques on how to cope with the
capacitive, resistive and inductive parasitics that come with interconnect wires. In this sec-
chapter9.fm Page 439 Friday, April 5, 2002 4:15 PM
Section 9.5
Advanced Interconnect Techniques
439
tion, we discuss a number of more-advanced circuits that have emerged in recent years.
More specifically, we discuss how reducing the signal swing can help to reduce the delay
and the power dissipation when driving wires with large capacitances.
9.5.1
Reduced-Swing Circuits
Increasing the size of the driver transistor, and thus increasing the average current I av during switching, is only one way of coping with the delay caused by a large load capacitance.
Another approach could be the reduction of the signal swing at the output of the driver and
over the load capacitance. Intuitively, we can understand that reducing the charge that has
to be displaced may be beneficial to the performance of the gate. This is best understood
by revisiting the propagation-delay equation Eq. (5.16)
v2
tp =
C L ( v)
dv
∫ -------------i (v )
(9.12)
v1
Assuming tthat the load capacitance is a constant, we can derived a simplified expression
for the delay,
CL V swing
tp = --------------------I av
(9.13)
where Vswing = v2 - v1 equals the signal swing at the output, and I av is the average
(dis)charge current. This expression clearly demonstrates that the delay reduces linearly
with the signal swing, under the condition that the (dis)charge current is not affected by
the reduction in voltage swing. Just lowering the overall supply voltage does not work:
while reducing the swing, it also lowers the current by a similar ratio. This was demonstrated earlier in Figure 3.28, which showed that the equivalent resistance of a (dis)charge
transistor is approximately constant over a wide range of supply voltages. While potentially offering an increased performance, lower signal swings further carry the major benefit of lowering the dynamic power consumption, which can be substantial when the load
capacitance is large.
On the negative side, reduced signal swings result in smaller noise margins, and
hence impact the signal integrity and reliability. Furthermore, CMOS gates are not particularly effective in detecting and reacting to small signal changes, because of the relatively
small transconductance of the MOS device. In order to work properly and to achieve high
performance, reduced-swing circuits normally require amplifier circuits, whose task it is to
restore the signal to its full swing in a minimum amount of time and with a minimum
amount of extra energy consumption. The overhead of adding extra amplifiers is only justifiable for network nodes with a large fan-in, where the circuit can be shared over many
input gates. Typical examples of such nodes are the data or address buses of a microprocessor, or the data lines in a memory array. In the former case, the amplifier is most often
called a receiver, while in a memory it is named a sense amplifier .2
2
More details on sense amplifier circuits can be found in the later chapter on semiconductor memories.
chapter9.fm Page 440 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
440
Chapter 9
A typical diagram of a reduced-swing network, consisting of a driver, a large capacitance/resistance interconnect wire, and a receiver circuit, is shown in Figure 9.30. Many
different designs for both drivers and receivers have been devised [Zhang00], of which we
only discuss a few. In general, the reduced-swing circuits fall into two major categories,
static and dynamic (or precharged). Another differentiating factor between circuits is the
signalling technique. Most receivers circuits use a single-ended appraoch, where the
receiver detects an absolute change in voltage on a single wire. Other circuits use differential or double-ended signalling techniques, where both the signal and its complement are
transmitted, and the receiver detects a relative change in voltage between the two wires.
While the latter approach requires substantial more wiring real-estate, it has the advantage
of being more robust in the presence of noise.
Figure 9.30 Reduced-swing
interconnect circuit. The driver circuit
reduces the normal voltage swing to a
reduced value, while the receiver
detects the signal and restores it to the
normal swing value.
Out
In
driver
CL
receiver
Static Reduced-Swing Networks
The task of designing a reduced-swing network simplifies substantially when a second
lower supply rail VDDL is available. A simple and robust single-ended driver circuit using
that second supply is shown in Figure 9.31. The challenge is in the receiver design. Just
using an inverter does not work very well: the small swing at the input of the NMOS transistor results in a small pull-down current, and hence a slow high-to-low transition at the
output; furthermore, the low value of VDDL is not sufficient to turn off the PMOS transistor, which detoriates the performance even more, and causes static power dissipation to
occur in addition. A more refined receiver circuit, inspired by the DCVSL gate discussed
eralier, is shown in Figure 9.31 Using a low-voltage inverter, the complement of the input
VDD
VDD
VDD
VDD L
Out
In
VDDL
Out
CL
Figure 9.31 Single-ended, static
reduced-swing driver and receiver.
driver
receiver
signal is generated. The receiver now acts as a differential amplifier. The cross-coupled
load transistors ensure that the output is restored to VDD, and that no static power is con-
chapter9.fm Page 441 Friday, April 5, 2002 4:15 PM
Section 9.5
Advanced Interconnect Techniques
441
VDD
VDD
VDD
P1
In2
In
N3
P3
CL
P2
A
Out
B
N1
N2
(a)
Out
Figure 9.32 (a) Symmetric sourcefollower driver with level converter;
(b) Simulated waveforms;
VTn
A
(b)
B
|VTp|
In2
In
sumed in steady-state mode. The positive feedback helps to accelerate the transitions. The
disadvantage of the circuit is that it becomes unacceptably slow for low swing values.
A circuit that avoids the use of a second supply rail is shown in Figure 9.32. By
reversing the postions of the NMOS and the PMOS transistors in the final stage of the
driver, we have limited the signal swing on the interconnect from |VTp | to V DD-V Tn, or
approximately 2 threshold values below VDD. The symmetrical receiver/level converter
consists of two cross-coupled transistor pairs (P1-P2 and N1-N2), and two diode-connected transistors, which isolate the reduced-swing interconnect wire from the full-swing
output signal. To understand the operation of the receiver, assume that node In2 goes from
low to high, or from |VTp | to VDD-VTn. Initially, node A and B are at V
| Tp| and GND,
respectively. During the transition period, with both N3 and P3 conducting, A and B rise to
VDD-VTn as shown in Figure 9.32b. Consequently, N2 turns on, and Out goes to low. The
feedback transistor P1 pulls A further up to VDD to turn P2 completely off. In2 and B stay
at VDD-VTn . Note that there is no standby current path from VDD to GND through N3
although the gate-source voltage of N3 almost VTn . Since the circuit is symmetric, a similar explanation holds for the high-to-low transition. Since the main function of transistors
P1 and N1 is to provide positive feedback and to completely cut off P2 or N2, they can be
very weak, which minimize their fight against the driver. The sensing delay of the receiver
is as small as two inverter delays.
Problem 9.2 Energy Consumption of Reduced-Swing Receiver
Assuming that the capacitance is dominated by the load capacitance of the wire, derive the
energy-reduction per signal transition that the circuit of Figure 9.32 offers over the full-swing
version.
chapter9.fm Page 442 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
442
Chapter 9
The interconnect systems shown so far are all single-ended. Figure 9.33 shows a differential scheme. The driver generates two complimentary reduced-wing signals using a
second supply rail. The receiver is nothing less than a clocked sense-amplifier-based differential register, introduced earlier in Section 7.7. The differential approach offers a very
high rejection of common-mode noise signals such as supply-rail noise and crosstalk
interference. The signal-swing can hence be reduced to very low levels — operation with
swings as low as 200 mV has been demonstrated. The driver uses NMOS transistors for
both pull-up and pull-down. The receiver is a clocked unbalanced current-latch sense
amplifier, which is discharged and charged at every clock cycle. The main disadvantage of
the differential approach is the doubling of the number of wires, which certainly presents a
major concern in many designs. The extra clock signal adds further to the overhead.
In
VDD L
VDD
clk
CL
VDDL
d
out
d
CL
clk
Figure 9.33 Differential reducedswing interconnect system using an
dditional supply rail at the driver.
The receiver is a clocked
differential flip-flop [Burd00].
out
clk
Dynamic Reduced-Swing Networks
Another approach to speeding up the response of large fan-in circuits such as buses is to
make use of precharging, an example of which is shown in Figure 9.34. During φ = 0, the
bus wire is precharged to VDD through transistor M2. Because this device is shared by all
input gates, it can be made large enough to ensure a fast precharging time. During φ = 1,
the bus capacitance is conditionally discharged by one of the pull-down transistors. This
operation is slow because the large capacitance Cbus must be discharged through the small
pull-down device M1 .
A speed-up at the expense of noise margin can be obtained by observing that all
transitions on the bus are from high-to-low during evaluation. A faster response can be
obtained by moving the switching threshold of the subsequent inverter upwards. This
results in an asymmetrical gate. In a traditional inverter design, M3 and M4 are sized so
that tpHL and tpLH are identical, and the switching threshold (V M) of the inverter is situated
around 0.5 V DD. This means that the bus voltage Vbus has to drop over VDD /2 before the
output inverter switches. This can be avoided by making the PMOS device larger, moving
VM upwards. This causes the output buffer to start switching earlier.
The precharged approach can result in a substantial speed-up for the driving of large
capacitive lines. However, it also suffers from all the disadvantages of dynamic circuit
techniques—charge-sharing, leakage, and inadvertent charge loss as a result of cross talk
and noise. Cross talk between neighboring wires is especially an issue in densely wired
bus networks. The reduced noise margin NMH of the asymmetrical read-out inverter
makes this circuit particularly sensitive to these parasitic effects. Extreme caution and
chapter9.fm Page 443 Friday, April 5, 2002 4:15 PM
Section 9.5
Advanced Interconnect Techniques
443
V DD
φ
V DD
M2
M4
Bus
Out
(a)Circuit diagram.
In 1.φ
M1
Cbus
In 2.φ
C out
M3
2.5
V asym
2
V (Volt)
V bus
(b)Simulated response for both symmetrical and asymmetrical read-out
inverters. M 4 is made fifteen times
wider in the asymmetrical case.
The load capacitance equals 1 pF.
Vsym
1.5
φ
1
0.5
0
0
2
4
6
8
10
12
time (nsec)
Figure 9.34
Precharged bus.
extensive simulation is required when designing large precharged networks. However, the
speed benefit is sometimes worth the effort.
The simulated response of a precharged bus network is shown in Figure 9.34b. The
output signal is plotted for both symmetrical and asymmetrical output inverters. Skewing
the switching threshold upwards reduces the propragation delay with more than 2.5 nsec.
This allows for a further reduction in the evaluation period, which reduces the voltage
swing of the bus with 0.6 V and the energy consumption with 18%. Careful timing of the
precharge/evaluate signals is required to reap the maximum benefits of this scheme.
A variant on the dynamic theme is
VDD
offered by the pulse-controlled
REF
driver scheme of Figure 9.35. The
PRE
REF
Out
In
idea is to control the (dis)charging
SA
EN
CL
time of the drivers so that a desired
E N2
swing is obtained on the interconnect. The interconnect wire is precharged to a reference voltage
Figure 9.35 Pulse-controlled driver with sense amplifier
REF, typically situated at VDD/2.
The receiver consists of a differential sense amplifier, which compares the voltage on the
interconnect wire to REF. Since the amplifier consumes static power, it should only be
enable for a short while. The advantage of this circuit is that the pulse width can be finetuned to realize a very-low swing, while no extra voltage supply is needed. This concept
has been widely applied in memory designs. However, it only works well in the cases
chapter9.fm Page 444 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
444
Chapter 9
when the capacitive loads are well-known beforehand. Furthermore, the wire is floating
when the driver is disabled, making it susceptible to noise.
The circuits detailed above present only a small sub-group of the many reducedswing circuits that have been devised. A more complete overview can be found in
[Zhang00]. When venturing into the area of reduced-swing interconnect circuits, you
should always be aware of the trade-off’s involved: power and performance versus signal
integrity and reliability.
9.5.2
Current-Mode Transmission Techniques
All the approaches presented above assume that the data to be transmitted over the wire is
represented by a set of voltage levels, referenced to the supply rails. While this approach
conforms with the logical levels we typically use in digital logic, it does not necessarily
represent the best solution from a performance, power, and reliabilty perspective
[Dally98]. Consider the problem of transmitting a bit over a lengthy transmission line with
a characteristic impedance of 50 Ω. The traditional voltage-mode approach is depicted in
a. The driver switches the line between the two supply lines, that represent a 1 and a 0,
respectively, and has an impedance of Rout . The receiver is a CMOS inverter that compares the incoming voltage with a power-supply referenced threshold voltage, typically
centered in the middle of the two supply rails. The signal swing is lower-bounded by noise
considerations. More specifically, power supply noise has a large impact as it impact both
the signal levels and the switching threshold of the receiver. The latter is also a strong
function of manufacturing process variations.
VDD
R 0ut
Z0
(a)
+
Iin
Z0
RT
Figure 9.36 Voltage- versus
current-mode transmission
systems. The latter has the
advantage of higher noise
immunity with respect to
supply noise.
-
(b)
Another option is to use a low-swing current-mode transmission system as is shown
in b. The driver injects a current I in into the line for a 1 and a reserve current of -I in for a 0.
This induces a voltage wave of 2 × I in × Ζ0 into the transmission line, which ultimately
gets absorbed into the parallel termination resistance RT. The convergence time depends
on how well the termination resistance is matched to the characteristic impedance of the
chapter9.fm Page 445 Friday, April 5, 2002 4:15 PM
Section 9.6
Perspective: Networks-on-a-Chip
445
transmission line. A differential amplifier is used to the detect the voltage changes over
RT. Observe that the signal and its return path are both isolated from the supply rails and
the associated noise, making all supply-noise common-mode to the differential receiver.
Analog designers will testify that this type of noise is easily suppressed in any decent differential amplifier design.
While both approaches can be tuned to accomplish approximately the same performance levels, the current-mode approach holds a definite edge in terms of (dynamic)
power dissipation. Due to its immunity to power-supply noise, it can operate at a much
lower noise margin than the voltage-mode network, and hence also at a much lower
swing. The value of the voltage wave propagating over the transmission line can be as low
as 100 mV. The main challenge in designing an efficient current mode-circuit is the static
power consumption. This is not an issue in ultra high-speed networks, where dynamic
power tends to play the major role. Based on these observations, current-mode CMOS
transmission systems have become popular in the area of high-speed off-chip interconnections. We would not be surprised to see them emerge on-chip as well in the foreseeable
future.
9.6
Perspective: Networks-on-a-Chip
With chip sizes and clock rates continuing to increase, and feature sizes getting smaller at
a constant rate, it is quite simple to conjecture that interconnect problems will be with us
for some time to come. Physics constraints as such as the speed of light and thermal noise
determinate how fast and how reliably a communication over a “long” distance can be
established. As communication bottlenecks have been the major damper on hyper-supercomputer performance, similar constraints are starting to hamper integrated systems (“systems-on-a-chip”). New solutions conceived at the technology and circuit level only help to
temporarily postpone the problems. The only and ultimate solution is to address interconnections on a chip as a communication problem, and to apply techniques and approaches
that have made large-world communications and networking systems work reliably and
correctly for quite some time. For example, the fact that the Internet is working correctly
given it spanning scope and the numbers of connection points is quite amazing. The secret
to its success is a well-thought-out protocol stack that isolates and orthoganizes the various functionality, performance, and reliability concenrns. So, rather than considering onchip interconnections as point-to-point wires, they should be abstracted as communication
channels over which we want to transmit data within a “quality-of-service” setting, putting
constraints on throughtput, latency, and correctness [Sgroi01].
As an example, today’s on-chip interconnect signalling techniques are designed
with noise margins large enough to ensure that a bit will always be transmitted correctly. It
is probably safe to conjecture that future designs might take a more extreme tack: give up
on integrity all together for the sake of energy/performance, and allow errors to occur on
the transmitted signals. These errors can be taken care off by other circuitry, that provides
error-correcting capabilities and/or retransmit corrupted data.
On a higher level of abstraction, we already are witnessing the emergence of complete “networks” on a chip. Rather than being statically wired from source-to-destination,
chapter9.fm Page 446 Friday, April 5, 2002 4:15 PM
COPING WITH INTERCONNECT
446
Chapter 9
data is injected as packets into a complete network of wires, switches, and routers, and it is
the network that dynamically decides how and when to route these packets through its
segments [Dally01]. Ultimately, this is the only approach that can reliably work when the
discrepancy between device sizes and on-chip distances becomes macroscopic.
9.7
Chapter Summary
This chapter has introduced a number of techniques to cope with the impact of interconnect on the performance and reliability of digital integrated circuits. The parasitics introduced by the interconnect have a dual effect on circuit operation: (1) they introduce noise
and (2) they increase the propagation delay and power dissipation.
• Capacitive cross-talk in dense wire networks affects the reliability of the system,
and impacts the performance. Careful design using well-behaved regular structures
or using advanced design-automation tools is a necessity. Providing the necessary
shielding is important for wires such as busses or clock signals.
• Driving large capacitances rapidly in CMOS requires the introduction of a cascade
of buffer stages that must be carefully sized. More advanced techniques include the
lowering of the signal-swing on long wires, and the use of current-mode signalling.
• Resistivity affects the reliability of the circuit by introducing RI drops. This is especially important for the supply network, where wire sizing is important.
• The extra delay introduced by the rc effects can be minimized by partitioning of the
wire and by using a better interconnect technology.
• The inductance of the interconnect becomes important at higher switching speeds.
The chip package is currently one of the most important contributors of inductance.
Novel packaging techniques are gaining importance with faster technologies.
• Ground bounce introduced by the L di/dt voltage drop over the supply wires is one
of the most important sources of noise in current integrated circuits. Ground bounce
can be reduced by providing sufficient supply pins and by controlling the slopes of
the off-chip signals.
• Transmission line effects are rapifly becoming an issue in super-GHz designs. Providing the correct termination is the only means of dealing with the transmission
line delay.
9.8
To Probe Further
Excellent overviews of the issues involved in dealing with interconnect in digital designs
can be found in [Dally98] and [Bakoglu90]. Chandrakasan book - others? journals?
chapter9.fm Page 447 Friday, April 5, 2002 4:15 PM
Section 9.8
To Probe Further
447
REFERENCES
[Abo92] A. Abo and A. Behzad, “Interconnect Driver Design,” EE141 Project Report, Univ. of California—Berkeley, 1992.
[Bakoglu90] H. Bakoglu, Circuits, Interconnections and Packaging for VLSI, Addison-Wesley,
1990.
[Brews89] J. Brews, “Electrical Modeling of Interconnections,” in SubMicron Integrated Circuits,
ed. R. Watts, John Wiley & Sons, pp. 269–331, 1989.
[Doane93] D. Doane, ed., Multichip Module Technologies and Alternatives, Van Nostrand-Reinhold, 1993.
[Dopperpuhl92] D. Dopperpuhl et al., “A 200 MHz 64-b Dual Issue CMOS Microprocessor,” IEEE
Journal of Solid State Circuits, vol. 27, no. 11, pp. 1555–1567, November 1992.
[Elmore48] E. Elmore, “The Transient Response of Damped Linear Networks with Particular
Regard to Wideband Amplifiers,” Journal of Applied Physics, pp. 55–63, January 1948.
[Etter93] D. Etter, “Engineering Problem Solving with Matlab,” Prentice Hall, 1993.
[Franzon93] P. Franzon, “Electrical Design of Digital Multichip Modules,” in [Doane93], pp
525–568, 1993.
[Heller75] L. Heller et al., “High-Sensitivity Charge-Transfer Sense Amplifier,” Proceedings ISSCC
Conf., pp. 112-113, 1975.
[Hedenstierna87] N. Hedenstierna et al., “CMOS Circuit Speed and Buffer Optimization,” IEEE
Trans. on Computer-Aided Design, vol CAD-6, no. 2, pp. 270–281, March 1987.
[Horowitz83] M. Horowitz, “Timing Models for MOS Circuits,” Ph.D. diss., Stanford University,
1983.
[Johnson93] H. Johnson and M. Graham, High-Speed Digital Design—A Handbook of Black Magic,
Prentice Hall, 1993.
[Kang87] S. Kang, “Metal-Metal Matrix (M3) for High-Speed MOS VLSI Layout,” IEEE Trans.
Computer-Aided Design, vol. CAD-6, pp. 886–891, September 1987.
[Landman71] B. Landman and R. Russo, “On a Pin versus Block Relationship for Partitions of
Logic Graphs,” IEEE Trans. on Computers, vol. C-20, pp. 1469–1479, December 1971.
[Masaki92] A. Masaki, “Deep-Submicron CMOS Warms Up to High-Speed Logic,” Circuits and
Devices Magazine, Nov. 1992.
[Mead80] C. Mead and L. Conway, Introduction to VLSI Systems, Addison-Wesley, 1980.
[Nagata92] M. Nagata, “Limitations, Innovations, and Challenges of Circuits and Devices into a
Half Micrometer and Beyond,” IEEE Journal of Solid State Circuits, vol. 27, no. 4, pp. 465–472,
April 1992.
[Rubinstein83] J. Rubinstein, P. Penfield, and M. Horowitz, “Signal Delay in RC Networks,” IEEE
Transactions on Computer-Aided Design, vol. CAD-2, pp. 202–211, July 1983.
[Schaper83] L. Schaper and D. Amey, “Improved Electrical Performance Required for Future MOS
Packaging,” IEEE Trans. on Components, Hybrids and Manufacturing Technology, vol. CHMT6, pp. 282–289, September 1983.
[Solomon82] P. Solomon, “A Comparison of Semiconductor Devices for High-Speed Logic,” Proc.
of the IEEE, vol. 70, no. 5, May 1982.
[Sorkin87] G. Sorkin, “Asymptotically Perfect Trivial Global Routing: A Stochastic Analysis,”
IEEE Trans. on Computer-Aided Design, vol. CAD-6, p. 820, 1987.
[Steidel83] C. Steidel, “Assembly Techniques and Packaging,” in [Sze83], pp. 551–598, 1983.
chapter9.fm Page 448 Friday, April 5, 2002 4:15 PM
448
COPING WITH INTERCONNECT
Chapter 9
[Sze81] S. Sze, Physics of Semi-Conductor Devices, 2nd ed., Wiley, 1981.
[Sze83] S. Sze, ed., VLSI Technology, McGraw-Hill, 1983.
[Tao94] J. Tao, N. Cheung, and C. Hu, “An Electromigration Failure Model for Interconnects under
Pulsed and Bidirectional Current Stressing,” IEEE Trans. on Devices, vol. 41, no. 4, pp.
539–545, April 1994.
[Tewksbury94] S. Tewksbury, ed., Microelectronics System Interconnections—Performance and
Modeling, IEEE Press, 1994.
[Vaidya80] S. Vaidya, D. Fraser, and A. Sinha, “Electromigration Resistance of Fine-Line Al,”
Proc. 18th Reliability Physics Symposium, IEEE, p. 165, 1980.
[Vdmeijs84] N. Van De Meijs and J. Fokkema, “VLSI Circuit Reconstruction from Mask Topology,” Integration, vol. 2, no. 2, pp. 85–119, 1984.
[Wada92] O. Wada, T. Kamijoh, and M. Nakamura, “Integrated Optical Connections,” IEEE Circuits and Devices Magazine, vol. 8, no. 6, pp. 37–42, 1992.
[Weste93] N. Weste and K.Eshragian, Principles of CMOS VLSI Design: A Systems Perspective,
2nd ed., Addison-Wesley, 1993.
[Yoshino90] T. Yoshino et al., “A 100 MHz 64-tap FIR Digital Filter in a 0.8 µm BiCMOS Gate
Array,” IEEE Journal of Solid State Circuits, vol. 25, no. 6, pp. 1494–1501, December 1990.
chapter10_141.fm Page 42 Tuesday, April 16, 2002 9:12 AM
CHAPTER
10
TIMING ISSUES
IN DIGITAL CIRCUITS
Impact of clock skew and jitter on performance and functionality
n
Alternative timing methodologies
n
Synchronization issues in digital IC and board design
n
Clock generation
10.1 Introduction
10.5 Synchronizers and Arbiters*
10.2 Classification of Digital Systems
10.6 Clock Synthesis and Synchronization Using a
Phase-Locked Loop
10.3 Synchronous Design — An In-depth
Perspective
10.3.1Synchronous Timing Basics
10.3.2Sources of Skew and Jitter
10.3.3Clock-Distribution Techniques
10.7 Future Directions
10.8 Perspective: Synchronous versus
Asynchronous Design
10.9 Summary
10.10 To Probe Further
10.3.4Latch-Based Clocking
10.4 Self-Timed Circuit Design*
42
chapter10_141.fm Page 43 Tuesday, April 16, 2002 9:12 AM
43
10.1
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Introduction
All sequential circuits have one property in common—a well-defined ordering of the
switching events must be imposed if the circuit is to operate correctly. If this were not the
case, wrong data might be written into the memory elements, resulting in a functional failure. The synchronous system approach, in which all memory elements in the system are
simultaneously updated using a globally distributed periodic synchronization signal (that
is, a global clock signal), represents an effective and popular way to enforce this ordering.
Functionality is ensured by imposing some strict contraints on the generation of the clock
signals and their distribution to the memory elements distributed over the chip; non-compliance often leads to malfunction.
This Chapter starts with an overview of the different timing methodologies. The
majority of the text is devoted to the popular synchronous approach. We analyze the
impact of spatial variations of the clock signal, called clock skew, and temporal variations
of the clock signal, called clock jitter, and introduce techniques to cope with it. These variations fundamentally limit the performance that can be achieved using a conventional
design methodology.
At the other end of the design spectrum is an approach called asynchronous design,
which avoids the problem of clock uncertainty all-together by eliminating the need for
globally-distributed clocks. After discussing the basics of asynchronous design approach,
we analyze the associated overhead and identify some practical applications. The important issue of synchronization, which is required when interfacing different clock domains
or when sampling an asynchronous signal, also deserves some in-depth treatment. Finally,
the fundamentals of on-chip clock generation using feedback is introduced along with
trends in timing.
10.2
Classification of Digital Systems
In digital systems, signals can be classified depending on how they are related to a local
clock [Messerschmitt90][Dally98]. Signals that transition only at predetermined periods
in time can be classified as synchronous, mesochronous, or plesiochronous with respect to
a system clock. A signal that can transition at arbitrary times is considered asynchronous.
10.2.1
Synchronous Interconnect
A synchronous signal is one that has the exact same frequency, and a known fixed phase
offset with respect to the local clock. In such a timing methodology, the signal is “synchronized” with the clock, and the data can be sampled directly without any uncertainty. In
digital logic design, synchronous systems are the most straightforward type of interconnect, where the flow of data in a circuit proceeds in lockstep with the system clock as
shown below.
Here, the input data signal In is sampled with register R1 to give signal Cin, which is
synchronous with the system clock and then passed along to the combinational logic
block. After a suitable setting period, the output Cout becomes valid and can be sampled by
chapter10_141.fm Page 44 Tuesday, April 16, 2002 9:12 AM
Section 10.2
Classification of Digital Systems
44
CLK
In
R1
Cin
Figure 10.1 Synchronous interconnect
methodology.
Combinational
Logic
R2
Cout
Out
R2 which synchronizes the output with the clock. In a sense, the “certainty period” of signal Cout, or the period where data is valid is synchronized with the system clock, which
allows register R2 to sample the data with complete confidence. The length of the “uncertainty period,” or the period where data is not valid, places an upper bound on how fast a
synchronous interconnect system can be clocked.
10.2.2
Mesochronous interconnect
A mesochronous signal is one that has the same frequency but an unknown phase offset
with respect to the local clock (“meso” from Greek is middle). For example, if data is
being passed between two different clock domains, then the data signal transmitted from
the first module can have an unknown phase relationship to the clock of the receiving
module. In such a system, it is not possible to directly sample the output at the receiving
module because of the uncertainty in the phase offset. A (mesochronous) synchronizer can
be used to synchronize the data signal with the receiving clock as shown below. The synchronizer serves to adjust the phase of the received signal to ensure proper sampling.
Block A
R1
D1
Interconnect
Delay
D3
D2
R2
Block B
D4
ClkB
ClkA
PD/
Control
Figure 10.2 Mesochronous communication approach using variable delay line.
In Figure 10.2, signal D1 is synchronous with respect to ClkA. However, D1 and D2
are mesochronous with ClkB because of the unknown phase difference between ClkA and
ClkB and the unknown interconnect delay in the path between Block A and Block B. The
role of the synchronizer is to adjust the variable delay line such that the data signal D3 (a
delayed version of D2) is aligned properly with the system clock of block B. In this example, the variable delay element is adjusted by measuring the phase difference between the
received signal and the local clock. After register R2 samples the incoming data during the
certainty period, then signal D4 becomes synchronous with ClkB.
10.2.3
Plesiochronous Interconnect
A plesiochronous signal is one that has nominally the same, but slightly different frequency as the local clock (“plesio” from Greek is near). In effect, the phase difference
chapter10_141.fm Page 45 Tuesday, April 16, 2002 9:12 AM
45
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
drifts in time. This scenario can easily arise when two interacting modules have independent clocks generated from separate crystal oscillators. Since the transmitted signal can
arrive at the receiving module at a different rate than the local clock, one needs to utilize a
buffering scheme to ensure all data is received. Typically, plesiochronous interconnect
only occurs in distributed systems like long distance communications, since chip or even
board level circuits typically utilize a common oscillator to derive local clocks. A possible
framework for plesiochronous interconnect is shown in Figure 10.3.
Clock C2
Timing
Recovery
Clock C 1
C3
Originating
Module
Receiving
Module
FIFO
Figure 10.3 Plesiochronous communications using FIFO.
In this digital communications framework, the originating module issues data at
some unknown rate characterized by C1, which is plesiochronous with respect to C2. The
timing recovery unit is responsible for deriving clock C3 from the data sequence, and buffering the data in a FIFO. As a result, C3 will be synchronous with the data at the input of
the FIFO and will be mesochronous with C1. Since the clock frequencies from the originating and receiving modules are mismatched, data might have to be dropped if the transmit frequency is faster, and data can be duplicated if the transmit frequency is slower than
the receive frequency. However, by making the FIFO large enough, and periodically resetting the system whenever an overflow condition occurs, robust communication can be
achieved.
10.2.4
Asynchronous Interconnect
Asynchronous signals can transition at any arbitrary time, and are not slaved to any local
clock. As a result, it is not straightforward to map these arbitrary transitions into a synchronized data stream. Although it is possible to synchronize asynchronous signals by
detecting events and introducing latencies into a data stream synchronized to a local clock,
a more natural way to handle asynchronous signals is to simply eliminate the use of local
clocks and utilize a self-timed asynchronous design approach. In such an approach, communication between modules is controlled through a handshaking protocol to perform the
proper ordering of commands.
Data
Req
Reg
Self-Timed
Logic
I
Self-Timed
Logic
Reg
DV
I
DV
Interconnect Circuit
Interconnect Circuit
Ack
handshaking
signals
Figure 10.4 Asynchronous design methodology for simple pipeline interconnect.
chapter10_141.fm Page 46 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
46
When a logic block completes an operation, it will generate a completion signal DV
to indicate that output data is valid. The handshaking signals then initiate a data transfer to
the next block, which latches in the new data and begins a new computation by asserting
the initialization signal I. Asynchronous designs are advantageous because computations
are performed at the native speed of the logic, where block computations occur whenever
data becomes available. There is no need to manage clock skew, and the design methodology leads to a very modular approach where interaction between blocks simply occur
through a handshaking procedure. However, these handshaking protocols result in
increased complexity and overhead in communication that can reduce performance.
10.3
Synchronous Design — An In-depth Perspective
10.3.1
Synchronous Timing Basics
Virtually all systems designed today use a periodic synchronization signal or clock. The
generation and distribution of a clock has a significant impact on performance and power
dissipation. For a positive edge-triggered system, the rising edge of the clock is used to
denote the beginning and completion of a clock cycle. In the ideal world, assuming the
clock paths from a central distribution point to each register are perfectly balanced, the
phase of the clock (i.e., the position of the clock edge relative to a reference) at various
points in the system is going to be exactly equal. However, the clock is neither perfectly
periodic nor perfectly simultaneous. This results in performance degradation and/or circuit
malfunction. Figure 10.5 shows the basic structure of a synchronous pipelined datapath. In
R1
In
D
CLK
Q
Combinational
Logic
R2
D
tCLK1
tc-q
tc-q, cd
tsu, thold
Q
tCLK2
tlogic
tlogic, cd
Figure 10.5 Pipelined Datapath Circuit and timing parameters.
the ideal scenario, the clock at registers 1 and 2 have the same clock period and transition
at the exact same time. The following timing parameters characterize the timing of the
sequential circuit.
• The contamination (minimum) delay tc-q,cd, and maximum propagation delay of the
register tc-q.
• The set-up (tsu) and hold time (thold) for the registers.
• The contamination delay tlogic,cd and maximum delay tlogic of the combinational
logic.
chapter10_141.fm Page 47 Tuesday, April 16, 2002 9:12 AM
47
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
• tclk1 and tclk2, corresponding to the position of the rising edge of the clock relative to
a global reference.
Under ideal conditions (tclk1 = tclk2), the worst case propagation delays determine the
minimum clock period required for this sequential circuit. The period must be long
enough for the data to propagate through the registers and logic and be set-up at the destination register before the next rising edge of the clock. This constraint is given by (as
derived in Chapter 7):
T > t c – q + t log ic + t su
(10.1)
At the same time, the hold time of the destination register must be shorter than the minimum propagation delay through the logic network,
t ho ld < t c – q, cd + t log ic, cd
(10.2)
The above analysis is simplistic since the clock is never ideal. As a result of process and
environmental variations, the clock signal can have spatial and temporal variations.
Clock Skew
The spatial variation in arrival time of a clock transition on an integrated circuit is commonly referred to as clock skew. The clock skew between two points i and j on a IC is
given by δ (i,j) = ti- tj, where ti and tj are the position of the rising edge of the clock with
respect to a reference. Consider the transfer of data between registers R1 and R2 in Figure
10.5. The clock skew can be positive or negative depending upon the routing direction and
position of the clock source. The timing diagram for the case with positive skew is shown
in Figure 10.6. As the figure illustrates, the rising clock edge is delayed by a positive δ at
the second register.
TCLK + δ
CLK1
CLK2
1
TCLK
δ
2
3
4
δ + th
Figure 10.6 Timing diagram to study the impact of clock skew on performance and funcationality. In
this sample timing diagram, δ > 0.
Clock skew is caused by static path-length mismatches in the clock load and by definition skew is constant from cycle to cycle. That is, if in one cycle CLK2 lagged CLK1 by
δ, then on the next cycle it will lag it by the same amount. It is important to note that clock
skew does not result in clock period variation, but rather phase shift.
chapter10_141.fm Page 48 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
48
TCLK + δ
1
CLK1
CLK2
TCLK
2δ
3
4
Figure 10.7 Timing diagram for the case when δ < 0. The rising edge of CLK2 arrives
earlier than the edge of CLK1.
Skew has strong implications on performance and functionality of a sequential system. First consider the impact of clock skew on performance. From Figure 10.6, a new
input In sampled by R1 at edge
will propagate through the combinational logic and be
sampled by R2 on edge . If the clock skew is positive, the time available for signal to
propagate from R1 to R2 is increased by the skew δ. The output of the combinational logic
must be valid one set-up time before the rising edge of CLK2 (point ). The constraint on
the minimum clock period can then be derived as:
1
4
4
T + δ ≥ t c – q + t log ic + t su
or
T ≥ t c – q + t log ic + t su – δ
(10.3)
The above equation suggests that clock skew actually has the potential to improve
the performance of the circuit. That is, the minimum clock period required to operate the
circuit reliably reduces with increasing clock skew! This is indeed correct, but unfortunately, increasing skew makes the circuit more susceptible to race conditions may and
harm the correct operation of sequential systems.
As above, assume that input In is sampled on the rising edge of CLK1 at edge into
R1. The new values at the output of R1 propagates through the combinational logic and
should be valid before edge
at CLK2. However, if the minimum delay of the combinational logic block is small, the inputs to R2 may change before the clock edge , resulting
in incorrect evaluation. To avoid races, we must ensure that the minimum propagation
delay through the register and logic must be long enough such that the inputs to R2 are
valid for a hold time after edge . The constraint can be formally stated as
1
4
2
2
δ + t hol d < t ( c – q, cd ) + t ( log ic, cd )
or
δ < t ( c – q, cd ) + t ( log ic, cd ) – t hold
(10.4)
Figure 10.7 shows the timing diagram for the case when δ < 0. For this case, the rising edge of CLK2 happens before the rising edge of CLK1. On the rising edge of CLK1, a
new input is sampled by R1. The new sampled data propagates through the combinational
logic and is sampled by R2 on the rising edge of CLK2, which corresponds to edge . As
can be seen from Figure 10.7 and Eq. (10.3), a negative skew directly impacts the performance of sequential system. However, a negative skew implies that the system never fails,
since edge
happens before edge ! This can also be seen from Eq. (10.4), which is
always satisfied since δ < 0.
4
2
1
chapter10_141.fm Page 49 Tuesday, April 16, 2002 9:12 AM
49
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Example scenarios for positive and negative clock skew are shown in Figure 10.8.
In
R1
Combinational
Logic
Q
D
R2
tCLK1
CLK
Combinational
Logic
Q
D
R3
D
tCLK2
Q
tCLK3
delay
delay
(a) Positive skew
In
R1
Combinational
Logic
Q
D
R2
D
Combinational
Logic
Q
tCLK1
R3
D
Q
tCLK3
tCLK2
delay
CLK
delay
(b) Negative skew
Figure 10.8 Positive and negative clock skew.
• δ > 0—This corresponds to a clock routed in the same direction as the flow of the data
through the pipeline (Figure 10.8a). In this case, the skew has to be strictly controlled
and satisfy Eq. (10.4). If this constraint is not met, the circuit does malfunction independent of the clock period. Reducing the clock frequency of an edge-triggered circuit
does not help get around skew problems! On the other hand, positive skew increases the
throughput of the circuit as expressed by Eq. (10.3), because the clock period can be
shortened by δ. The extent of this improvement is limited as large values of δ soon provoke violations of Eq. (10.4).
• δ < 0—When the clock is routed in the opposite direction of the data (Figure 10.8b), the
skew is negative and condition (10.4) is unconditionally met. The circuit operates correctly independent of the skew. The skew reduces the time available for actual computation so that the clock period has to be increased by |δ|. In summary, routing the clock in
the opposite direction of the data avoids disasters but hampers the circuit performance .
Unfortunately, since a general logic circuit can have data flowing in both directions (for
example, circuits with feedback), this solution to eliminate races will not always work (Figure
10.9). The skew can assume both positive and negative values depending on the direction of
In
REG
Logic
Logic
CLK
Positive skew
CLK
Clock distribution
Figure 10.9 Datapath structure with feedback.
REG
CLK
REG
REG
Negative skew
CLK
Logic
Out
chapter10_141.fm Page 50 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
50
the data transfer. Under these circumstances, the designer has to account for the worst-case
skew condition. In general, routing the clock so that only negative skew occurs is not feasible.
Therefore, the design of a low-skew clock network is essential.
Example 10.1
Propagation and Contamination Delay Estimation
Consider the logic network shown in Figure 10.10. Determine the propagation and contamination delay of the network, assuming that the worst case gate delay is tgate. The maximum
and minimum delays of the gates is made, as they are assumed to be identical.
The contamination delay is given by 2 tgate (the delay through OR1 and OR2). On the
other hand, computation of the worst case propagation delay is not as simple as it appears. At
first glance, it would appear that the worst case corresponds to path
and the delay is 5tgate.
However, when analyzing the data dependencies, it becomes obvious that path
is never
exercised. Path
is called a false path. If A = 1, the critical path goes through OR1 and OR2.
If A = 0 and B = 0, the critical path is through I1,OR1 and OR2 (corresponding to a delay of 3
tgate). For the case when A= 0 and B =1, the critical path is through I1,OR1, AND 3 and OR2. In
other words, for this simple (but contrived) logic circuit, the output does not even depend on
inputs C and D (that is, there is redundancy). Therefore, the propagation delay is 4 tgate. Given
the propagation and contamination delay, the minimum and maximum allowable skew can be
easily computed.
1
1
path
A
B
C
OR1
I1
AND1
1
2
OR2
1
path
AND2
AND 3
D
Figure 10.10 Logic network for computation of performance.
WARNING: The computation of the worst-case propagation delay for combinational
logic, due to the existence of false paths, cannot be obtained by simply adding the propagation delay of individual logic gates. The critical path is strongly dependent on circuit
topology and data dependencies.
Clock Jitter
Clock jitter refers to the temporal variation of the clock period at a given point — that is,
the clock period can reduce or expand on a cycle-by-cycle basis. It is strictly a temporal
uncertainty measure and is often specified at a given point on the chip. Jitter can be measured and cited in one of many ways. Cycle-to-cycle jitter refers to time varying deviation
chapter10_141.fm Page 51 Tuesday, April 16, 2002 9:12 AM
51
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
of a single clock period and for a given spatial location i is given as Tjitter,i(n) = Ti, n+1 - Ti,n
- TCLK, where Ti,n is the clock period for period n, Ti, n+1 is clock period for period n+1, and
TCLK is the nominal clock period.
Jitter directly impacts the performance of a sequential system. Figure 10.11 shows
the nominal clock period as well as variation in period. Ideally the clock period starts at
edge and ends at edge and with a nominal clock period of TCLK. However, as a result
of jitter, the worst case scenario happens when the leading edge of the current clock period
is delayed (edge ), and the leading edge of the next clock period occurs early (edge ).
As a result, the total time available to complete the operation is reduced by 2 tjiiter in the
worst case and is given by
2
5
3
4
TCLK – 2t j itt er ≥ t c – q + t log i c + t su or T ≥ t c – q + t log ic + t su + 2t j itt er
(10.5)
The above equation illustrates that jitter directly reduces the performance of a sequential
circuit. Care must be taken to reduce jitter in the clock network to maximize performance.
TCLK
CLK
2
1 3
4
5
-tjitter
In
tjitter
6
REGS
Combinational
Logic
CLK
tc-q , tc-q, cd
tsu, thold
tjitter
tlogic
tlogic, cd
Figure 10.11 Circuit for studying the impact of jitter on performance.
Impact of Skew and Jitter on Performance
In this section, the combined impact of skew and jitter is studied with respect to conventional edge-triggered clocking. Consider the sequential circuit show in Figure 10.12.
Assume that nominally ideal clocks are distributed to both registers (the clock
period is identical every cycle and the skew is 0). In reality, there is static skew δ between
the two clock signals (assume that δ > 0). Assume that CLK1 has a jitter of tjitter1 and
CLK2 has a jitter of tjitter2. To determine the constraint on the minimum clock period, we
must look at the minimum available time to perform the required computation. The worst
case happen when the leading edge of the current clock period on CLK1 happens late
(edge ) and the leading edge of the next cycle of CLK2 happens early (edge ). This
results in the following constraint
3
T CLK + δ – t j itt er1 – t jit ter2 ≥ t c – q + t log i c + t su
or T ≥ t c – q + t log ic + t su – δ + t jit ter1 + t jit ter2
(10.6)
chapter10_141.fm Page 52 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
52
R1
In
R2
Combinational
Logic
Q
D
Q
D
tCLK1
2 5
8
tCLK2
11
TCLK + δ
TCLK
tjitter1
CLK1
1 3
7 9
δ
CLK2
tjitter2
4 6
12
Figure 10.12 Sequential circuit to study the impact of skew and jitter on edge-triggered
systems. In this example, a positive skew (δ) is assumed.
As the above equation illustrates, while positive skew can provide potential performance advantage, jitter has a negative impact on the minimum clock period. To formulate
the minimum delay constraint, consider the case when the leading edge of the CLK1 cycle
arrives early (edge ) and the leading edge the current cycle of CLK2 arrives late (edge
). The separation between edge
and
should be smaller than the minimum delay
through the network. This results in
1
6
1
6
δ + t hold + t ji tter1 + t ji tte r2 < t ( c – q, c d) + t ( log i c, cd )
or
δ < t ( c – q, cd ) + t ( log ic, cd ) – t hold – t j itt er1 – t jit ter2
(10.7)
The above relation indicates that the acceptable skew is reduced by the jitter of the two
signals.
Now consider the case when the skew is negative (δ <0) as shown in Figure 10.13.
For the timing shown, |δ| > tjitter2. It can be easily verified that the worst case timing is
exactly the same as the previous analysis, with δ taking a negative value. That is, negative
skew reduces performance.
25
8
TCLK + δ
CLK1
CLK2
tjitter1
36
1 4
tjitter2
11
δ<0
TCLK
9
12
7
Figure 10.13 Consider a negative clock skew (δ) and the skew is assumed to be larger than the jitter.
chapter10_141.fm Page 53 Tuesday, April 16, 2002 9:12 AM
53
TIMING ISSUES IN DIGITAL CIRCUITS
10.3.2
Chapter 10
Sources of Skew and Jitter
A perfect clock is defined as perfectly periodic signal that is simultaneous triggered at various memory elements on the chip. However, due to a variety of process and environmental variations, clocks are not ideal. To illustrate the sources of skew and jitter, consider the
simplistic view of clock generation and distribution as shown in Figure 10.14. Typically, a
high frequency clock is either provided from off chip or generated on-chip. From a central
point, the clock is distributed using multiple matched paths to low-level memory element.s registers. In this picture, two paths are shown. The clock paths include wiring and
the associated distributed buffers required to drive interconnects and loads. A key point to
realize in clock distribution is that the absolute delay through a clock distribution path
is not important; what matters is the relative arrival time between the output of each path
at the register points (i.e., it is pefectly acceptable for the clock signal to take multiple
cycles to get from a central distribution point to a low-level register as long as all clocks
arrive at the same time to different registers on the chip).
Devices
1
4
2
Power Supply
Clock Generation
3
5
Interconnect
Temperature
6
Capacitive Load
7
Coupling to Adjacent Lines
Figure 10.14 Skew and jitter sources in synchronous clock distribution.
The are many reasons why the two parallel paths don’t result in exactly the same
delay. The sources of clock uncertainty can be classified in several ways. First, errors can
be divided into systematic or random. Systematic errors are nominally identical from chip
to chip, and are typically predictable (e.g., variation in total load capacitance of each clock
path). In principle, such errors can be modeled and corrected at design time given sufficiently good models and simulators. Failing that, systematic errors can be deduced from
measurements over a set of chips, and the design adjusted to compensate. Random errors
are due to manufacturing variations (e.g., dopant fluctuations that result in threshold variations) that are difficult to model and eliminate. Mismatch may also be characterized as
static or time-varying. In practice, there is a continuum between changes that are slower
than the time constant of interest, and those that are faster. For example, temperature variations on a chip vary on a millisecond time scale. A clock network tuned by a one-time
calibration or trimming would be vulnerable to time-varying mismatch due to varying
thermal gradients. On the other hand, to a feedback network with a bandwidth of several
megahertz, thermal changes appear essentially static. For example, the clock net is usually
by far the largest single net on the chip, and simultaneous transitions on the clock drivers
induces noise on the power supply. However, this high speed effect does not contribute to
chapter10_141.fm Page 54 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
54
time-varying mismatch because it is the same on every clock cycle, affecting each rising
clock edge the same way. Of course, this power supply glitch may still cause static mismatch if it is not the same throughout the chip. Below, the various sources of skew and jitter, introduced in Figure 10.14, are described in detail.
Clock-Signal Generation (1)
The generation of the clock signal itself causes jitter. A typical on-chip clock generator, as
described at the end of this chapter, takes a low-frequency reference clock signal, and produces a high-frequency global reference for the processor. The core of such a generator is
a Voltage-Controlled Oscillator (VCO). This is an analog circuit, sensitive to intrinsic
device noise and power supply variations. A major problem is the coupling from the surrounding noisy digital circuitry through the substrate. This is particularly a problem in
modern fabrication processes that combine a lightly-doped epitaxial layer and a heavilydoped substrate (to combat latch-up). This causes substrate noise to travel over large distances on the chip. These noise source cause temporal variations of the clock signal that
propagate unfiltered through the clock drivers to the flip-flops, and result in cycle-to-cycle
clock-period variations. This jitter causes performance degradation.
Manufacturing Device Variations (2)
Distributed buffers are integral components of the clock distribution networks, as they are
required to drive both the register loads as well as the global and local interconnects. The
matching of devices in the buffers along multiple clock paths is critical to minimizing timing uncertainty. Unfortunately, as a result of process variations, devices parameters in the
buffers vary along different paths, resulting in static skew. There are many sources of variations including oxide variations (that affects the gain and threshold), dopant variations,
and lateral dimension (width and length) variations. The doping variations can affect the
depth of junction and dopant profiles and cause variations in electrical parameters such as
device threshold and parasitic capacitances. The orientation of polysilicon can also have a
big impact on the device parameters. Keeping the orientation the same across the chip for
the clock drivers is critical.
Variation in the polysilicon critical dimension, is particularly important as it translates directly into MOS transistor channel length variation and resulting variations in the
drive current and switching characteristics. Spatial variation usually consists of waferlevel (or within-wafer) variation and die-level (or within-die) variation. At least part of the
variation is systematic and can be modeled and compensated for. The random variations
however, ultimately limits the matching and skew that can be achieved.
chapter10_141.fm Page 55 Tuesday, April 16, 2002 9:12 AM
55
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Interconnect Variations (3)
Vertical and lateral dimension variations cause the interconnect capacitance and resistance
to vary across a chip. Since this variation is static, it causes skew between different paths.
One important source of interconnect variation is the Inter-level Dielectric (ILD) thickness
variations. In the formation of aluminum interconnect, layers of silicon dioxide are interposed between layers of patterned metallization. The oxide layer is deposited over a layer
of patterned metal features, generally resulting in some remaining step height or surface
topography. Chemical-mechanical polishing (CMP) is used to “planarize” the surface and
remove topography resulting from deposition and etch (as shown in Figure 10.15a). While
at the feature scale (over an individual metal line), CMP can achieve excellent planarity,
there are limitations on the planarization that can be achieved over a global range. This is
primarily caused due to variations in polish rate that is a function of the circuit layout density and pattern effects. Figure 10.15b shows this effect where the polish rate is higher for
the lower spatial density region, resulting in smaller dielectric thickness and higher capacitance.
The assessment and control of variation is of critical importance in semiconductor
process development and manufacturing. Significant advances have been made to develop
analytical models for estimating the ILD thickness variations based on spatial density.
Since this component is often predictable from the layout, it is possible to actually correct
for the systematic component at design time (e.g., by adding appropriate delays or making
the density uniform by adding “dummy fills”). Figure 10.16 shows the spatial pattern density and ILD thickness for a high performance microprocessor. The graphs show that there
is clear correlation between the density and the thickness of the dielectric. So clock distribution networks must exploit such information to reduce clock skew.
Other interconnect variations include deviation in the width of the wires and line
spacing. This results from photolithography and etch dependencies. At the lower levels of
metallization, lithographic effects are important while at higher levels etch effects are
important that depend on width and layout. The width is a critical parameter as it directly
impacts the resistance of the line and the wire spacing affects the wire-to-wire capaci(b) Reality
(a) Ideally
t=t1
Oxide
ρ1=low
ρ2=high
Metal
t=t2
t=t3
Figure 10.15 Inter-level Dielectric (ILD) thickness variation due to density (coutersy of
Duane Boning).
chapter10_141.fm Page 56 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
56
tance, which the dominant component of capacitance. A detailed review of device and
interconnect variations is presented in [Boning00].
(a) Pattern Density
(b) ILD thickness variation
Figure 10.16 Pattern density and ILD thickness variation for a high performance microprocessor.
Environmental Variations (4 and 5)
Environmental variations are probably the most significant and primarily contribute to
skew and jitter. The two major sources of environmental variations are temperature and
power supply. Temperature gradients across the chip is a result of variations in power dissipation across the die. This has particularly become an issue with clock gating where
some parts of the chip maybe idle while other parts of the chip might be fully active. This
results in large temperature variations. Since the device parameters (such as threshold,
mobility, etc.) depend strongly on temperature, buffer delay for a clock distribution network along one path can vary drastically for another path. More importantly, this component is time-varying since the temperature changes as the logic activity of the circuit
varies. As a result, it is not sufficient to simulate the clock networks at worst case corners
of temperature; instead, the worst-case variation in temperature must be simulated. An
interesting question is does temperature variation contribute to skew or to jitter? Clearly
the variation in temperature is time varying but the changes are relatively slow (typical
time constants for temperature on the order of milliseconds). Therefore it usually considered as a skew component and the worst-case conditions are used. Fortunately, using feedback, it is possible to calibrate the temperature and compensate.
Power supply variations on the hand is the major source of jitter in clock distribution networks. The delay through buffers is a very strong function of power supply as it
directly affects the drive of the transistors. As with temperature, the power supply voltage
is a strong function of the switching activity. Therefore, the buffer delay along one path is
very different than the buffer delay along another path. Power supply variations can be
classified into static (or slow) and high frequency variations. Static power supply variations may result from fixed currents drawn from various modules, while high-frequency
variations result from instantaneous IR drops along the power grid due to fluctuations in
switching activity. Inductive issues on the power supply are also a major concern since
they cause voltage fluctuations. This has particularly become a concern with clock gating
as the load current can vary dramatically as the logic transitions back and forth between
the idle and active states. Since the power supply can change rapidly, the period of the
chapter10_141.fm Page 57 Tuesday, April 16, 2002 9:12 AM
57
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
clock signal is modulated on a cycle-by-cycle basis, resulting in jitter. The jitter on two
different clock points maybe correlated or uncorrelated depending on how the power network is configured and the profile of switching patterns. Unfortunately, high-frequency
power supply changes are difficult to compensate even with feedback techniques. As a
result, power supply noise fundamentally limits the performance of clock networks.
Capacitive Coupling (✖and ✗ )
The variation in capacitive load also contributes to timing uncertainty. There are two
major sources of capacitive load variations: coupling between the clock lines and adjacent
signal wires and variation in gate capacitance. The clock network includes both the interconnect and the gate capacitance of latches and registers. Any coupling between the clock
wire and adjacent signal results in timing uncertainty. Since the adjacent signal can transition in arbitrary directions and at arbitrary times, the exactly coupling to the clock network
is not fixed from cycle-to-cycle. This results in clock jitter. Another major source of clock
uncertainty is variation in the gate capacitance related to the sequential elements. The load
capacitance is highly non-linear and depends on the applied voltage. In many latches and
registers this translates to the clock load being a function of the current state of the
latch/register (this is, the values stored on the internal nodes of the circuit), as well as the
next state. This causes the delay through the clock buffers to vary from cycle-to-cycle,
causing jitter.
Example 10.2 Data-dependent Clock Jitter
Consider the circuit shown in Figure 10.17, where a minimum-sized local clock buffer drives
a register (actually, four registers are driven, though only one is shown here). The simulation
shows CKb, the output of the first inverter for four possible transitions (0 0, 0 1, 1 0 and
1 1). The jitter on the clock based on data-dependent capacitance is illustrated. In general,
the only way to deal with this problem is to use registers that don’t exhibit a large variation in
load as a function of data — for example, the differential sense-amplifier register shown in
Chapter 7.
CK
T2
CKb
CK
CKb
CLK
2.5
Q
I1
I3
Voltage (V)
T1
D
CKb
1.5
CKb
CLK
0.5
CK
-0.5
0
0.1
0.2
time (ns)
Figure 10.17 Impact of data-dependent clock load on clock jitter for pass-transistor register.
0.3
0.4
chapter10_141.fm Page 58 Tuesday, April 16, 2002 9:12 AM
Section 10.3
10.3.3
Synchronous Design — An In-depth Perspective
58
Clock-Distribution Techniques
It is clear from the previous discussion that clock skew and jitter are major issues in digital
circuits, and can fundamentally limit the performance of a digital system. It is necessary to
design a clock network that minimizes skew and jitter. Another important consideration in
clock distribution is the power dissipation. In most high-speed digital processors, a majority of the power is dissipated in the clock network. To reduce power dissipation, clock networks must support clock conditioning — this is, the ability to shut down parts of the
clock network. Unfortunately, clock gating results in additional clock uncertainty.
In this section, an overview of basic constructs in high-performance clock distribution techniques is presented along with a case study of clock distribution in the Alpha
microprocessor. There are many degrees of freedom in the design of a clock network
including the type of material used for wires, the basic topology and hierarchy, the sizing
of wires and buffers, the rise and fall times, and the partitioning of load capacitances.
Fabrics for clocking
Clock networks typically include a network that is used to distribute a global reference to
various parts of the chip, and a final stage that is responsible for local distribution of the
clock while considering the local load variations. Most clock distribution schemes exploit
the fact that the absolute delay from a central clock source to the clocking elements is
irrelevant — only the relative phase between two clocking points is important. Therefore
one common approach to distributing a clock is to use balanced paths (or called trees).
The most common type of clock primitive is the H-tree network (named for the
physical structure of the network) as illustrated in Figure 10.18, where a 4x4 array is
shown. In this scheme, the clock is routed to a central point on the chip and balanced
paths, that include both matched interconnect as well as buffers, are used to distribute the
reference to various leaf nodes. Ideally, if each path is balanced, the clock skew is zero.
That is, though it might take multiple clock cycles for a signal to propagate from the central point to each leaf node, the arrival times are equal at every leaf node. However, in
reality, as discussed in the previous section, process and environmental variations cause
clock skew and jitter to occur.
CLK
Figure 10.18 Example of an H-tree clock-distribution
network for 16 leaf nodes.
The H-tree configuration is particularly useful for regular-array networks in which
all elements are identical and the clock can be distributed as a binary tree (for example,
arrays of identical tiled processors). The concept can be generalized to a more generic set-
chapter10_141.fm Page 59 Tuesday, April 16, 2002 9:12 AM
59
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Figure 10.19 An example RC-matched distribution for an
IBM Microprocessor [Restle98].
ting. The more general approach, referred to as routed RC trees, represents a floorplan that
distributes the clock signal so that the interconnections carrying the clock signals to the
functional sub-blocks are of equal length. That is, the general approach does not rely on a
regular physical structure. An example of a matched RC is shown in Figure 10.19. The
chip is partitioned into ten balanced load segments (tiles). The global clock driver distributes the clock to tile drivers located at the dots in the figure. A lower level RC-matched
tree is used to drive 580 additional drivers inside each tile.
Another important clock distribution template is the grid structure as shown in Figure 10.20 [Bailey00]. Grids are typically used in the final stage of clock network to distribute the clock to the clocking element loads. This approach is fundamentally different
from the balanced RC approach. The main difference is that the delay from the final driver
to each load is not matched. Rather, the absolute delay is minimized assuming that the grid
size is small. A major advantage of such a grid structure is that it allows for late design
changes since the clock is easily accessible at various points on the die. Unfortunately, the
penalty is the power dissipation since the structure has a lot of unnecessary interconnect.
It is essential to consider clock distribution in the earlier phases of the design of a
complex circuit, since it might influence the shape and form of the chip floorplan. Clock
distribution is often only considered in the last phases of the design process, when most of
the chip layout is already frozen. This results in unwieldy clock networks and multiple
GCLK
Driver
Driver
Driver
GCLK
Driver
GCLK
GCLK
Figure 10.20 Grid structures allow a low skew
distribution and physical design flexibility at the
cost of power dissipation [Bailey00].
chapter10_141.fm Page 60 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
60
timing constraints that hamper the performance and operation of the final circuit. With
careful planning, a designer can avoid many of these problems, and clock distribution
becomes a manageable operation.
Case Study—The Digital Alpha Microprocessors
In this section, the clock distribution strategy for three generations of the Alpha microprocessor is discussed in detail. These processors have always been at the cutting edge of the
technology, and therefore represent an interesting perspective on the evolution of clock
distribution.
The Alpha 21064 Processor. The first generation Alpha microprocessor (21064 or EV4)
from Digital Equipment Corporation used a single global clock driver [Dobberpuhl92].
The distribution of clock load capacitance among various functional block shown in Figure 10.20, resulting in a total clock load of 3.25nF! The processor uses a single-phase
clock methodology and the 200Mhz clock is fed to a binary fanning tree with five levels of
buffering. The inputs to the clock drivers are shorted out to smooth out the asymmetry in
the incoming signals. The final output stage, residing in the middle of the chip, drives the
clock net. The clock driver and the associated pre-drivers account for 40% of the effective
switched capacitance (12.5nF), resulting in significant power dissipation. The overall
width of the clock driver was on the order of 35cm in a 0.75µm technology. A detail clock
skew simulation with process variations indicates that a clock uncertainty of less than
200psec (< 10%) was achieved.
clock driver
(35cm width)
ICache
373pF
Integer Unit Write
Buffer
1129pF
82pF
Data
Floating Unit Cache
208pF
803pF
Figure 10.21 Clock load for the .
The Alpha 21164 Processor . The Alpha 21164 microprocessor (EV5) operates at a
clock frequency of 300 Mhz while using 9.3 million transistors on a 16.5 mm × 18.1 mm
die in a 0.5 µm CMOS technology [Bowhill95]. A single-phase clocking methodology
was selected and the design made extensive use of dynamic logic, resulting in a substantial
clock load of 3.75 nF. The clock-distribution system consumes 20 W, which is 40% of the
total dissipation of the processor.
The incoming clock signal is first routed through a single six-stage buffer placed at
the center of the chip. The resulting signal is distributed in metal-3 to the left and right
banks of final clock drivers, positioned between the secondary cache memory and the outside edge of the execution unit (Figure 10.22a). The produced clock signal is driven onto a
grid of metal-3 and metal-4 wires. The equivalent transistor width of the final driver
inverter equals 58 cm! To ensure the integrity of the clock grid across the chip, the grid
was extracted from the layout, and the resulting RC-network was simulated. A threedimensional representation of the simulation results is plotted in Figure 10.22b. As evi-
chapter10_141.fm Page 61 Tuesday, April 16, 2002 9:12 AM
61
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Clock driver
(a) Chip microphotograph, showing positioning of clock drivers.
(b) Clock skew simulation.
Figure 10.22 Clock distribution and skew in 300 MHz microprocessor (Courtesy of Digital Equipment
Corporation).
dent from the plot, the skew is zero at the output of the left and right drivers. The maximum value of the absolute skew is smaller than 90 psec. The critical instruction and
execution units all see the clock within 65 psec.
Clock skew and race problems were addressed using a mix-and-match approach.
The clock skew problems were eliminated by either routing the clock in the opposite direction of the data at a small expense of performance or by ensuring that the data could not
overtake the clock. A standardized library of level-sensitive transmission-gate latches was
used for the complete chip. To avoid race-through conditions, a number of design guidelines were followed including:
• Careful sizing of the local clock buffers so that their skew was minimal.
• At least one gate had to be inserted between connecting latches. This gate, which
can be part of the logic function or just a simple inverter, ensures that the signal cannot overtake the clock. Special design verification tools were developed to guarantee that this rule was obeyed over the complete chip.
To improve the inter-layer dielectric uniformity, filler
polygons were inserted between widely spaced lines (Figure
10.23). Though this may increase the capacitance to nearby
signal lines, the improved uniformity results in lower variation
and clock uncertainty. The dummy fills are automatically
inserted, and tied to one of the power rails (VDD or GND). This
technique is used in many processors for controlling the clock
skew.
This example demonstrates that managing clock skew
and clock distribution for large, high-performance synchro-
Figure 10.23 Dummy
fills reduce the ILD
variation and improve
clock skew.
chapter10_141.fm Page 62 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
62
nous designs is a feasible task. However, making such a circuit work in a reliable way
requires careful planning and intensive analysis.
The Alpha 21264 Processor. A hierarchical clocking scheme is used in the 600Mhz
Alpha 21264 (EV6) processor (in 0.35µm CMOS) as shown in Figure 10.24. The choice
of a hierarchical clocking scheme for this processor is significantly different than their
previous approaches, which did not have a hierarchy of clocks beyond the global clock
grid. Using a hierarchical clocking approach makes trade-off’s between power and skew
management. Power is reduced because the clocking networks for individual blocks can
be gated. As seen in previous generation microprocessors, the clock power contributes to a
large fraction of overall power consumption. Also the flexibility of having local clocks
provides the designers with more freedom with circuit styles at the module level. The
drawback of using a hierarchical clock network is that skew reduction becomes more difficult because clocks to various local registers may go through very different paths, which
may contribute to the skew. However, using timing verification tools, the skew can be
managed by tweaking of clock drivers.
Figure 10.24 Clock
hierarchy for the Alpha
21264 Processor.
The clock hierarchy consists of a global clock grid, called GCLK, that covers the
entire die. State elements and clocking points exist from 0 to 8 levels past GCLK. The onchip generated clock is routed to the center of the die and distributed using tree structures
to 16 distributed clock drivers (Figure 10.25). The global clock distribution network utilizes a windowpane configuration, that achieves low skew by dividing up the clock into 4
regions -- this reduces the distance from the drivers to the loads. Each grid pane is driven
from four sides, reducing the dependence on process variations. This also helps the power
supply and thermal problems as the drivers are distributed through the chip.
Use of a grid-ded clock has the advantage of reducing the clock skew and provides
universal availability of clock signals. The drawback clearly is the increased capacitance
of the Global Clock grid when compared to a tree distribution approach. Beyond the
GCLK is a major clock grid. The major clock grid are used to drive different large execution blocks within the chip including 1) Bus interface unit 2) integer issue and execution
units 3) floating point issue and execution units 4) instruction fetch and branch prediction
unit 5) load/store unit and 6) pad ring. The reason the major clocks were introduced was to
reduce power because the major clocks have localized loads, and can be sized appropriately to meet the skew and edge requirements for the local loading conditions.
chapter10_141.fm Page 63 Tuesday, April 16, 2002 9:12 AM
63
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
Figure 10.25 Global clock-distribution network in a window-pane structure.
The last hierarchy of clocks in the Alpha processor are the local clocks, which are
generated as needed from any other clock, and typically can be customized to meet local
timing constraints. The local clocks provide great flexibility in the design of the local logic
blocks, but at the same time, makes it significantly more difficult to manage skew. For
example, local clocks can be gated in order to reduce power, can be driven with wildly different loads, and can even be tweaked to enable time borrowing between different blocks.
Furthermore, the local clocks are susceptible to coupling from data lines as well because
they are local and not shielded like the global grid-ded clocks. As a result, the local clock
distribution is highly dependent on it’s local interconnection, and has to be designed very
carefully to manage local clock skew.
Design Techniques—Dealing with Clock Skew and Jitter
To fully exploit the improved performance of logic gates with technology scaling, clock
skew and jitter must be carefully addressed. Skew and jitter can fundamentally limit the
peformance of a digital circuits. Some guidelines for reducing of clock skew and jitter are
presented below.
1. To minimize skew, balance clock paths from a central distribution source to individual clocking elements using H-tree structures or more generally routed tree structures. When using routed clock trees, the effective clock load of each path that
includes wiring as well as transistor loads must be equalized.
2. The use of local clock grids (instead of routed trees) can reduce skew at the cost of
increased capacitive load and power dissipation.
3. If data dependent clock load variations causes significant jitter, differential registers
that have a data independent clock load should be used. The use of gated clocks to
save also results in data dependent clock load and increased jitter. In clock networks
where the fixed load is large (e.g., using clock grids), the data dependent variation
might not be significant.
4. If data flows in one direction, route data and clock in opposite directions. This elminates races at the cost of perfomance.
chapter10_141.fm Page 64 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
64
5. Avoid data dependent noise by shielding clock wires from adjacent signal wires. By
placing power lines (VDD or GND) next to the clock wires, coupling from neighboring signal nets can be minimized or avoided.
6. Variations in interconnect capacitance due to inter-layer dielectric thickness variation can be greatly reduced through the use of dummy fills. Dummy fills are very
common and reduce skew by increasing uniformity. Systematic variations should be
modeled and compensated for.
7. Variation in chip temperature across the die causes variations in clock buffer delay.
The use of feedback circuits based on delay locked loops as discussed later in this
chapter can easily compensate for temperature variations.
8. Power supply variation is a significant component of jitter as it impacts the cycle to
cycle delay through clock buffers. High frequency power supply variation can be
reduced by addition of on-chip decoupling capacitors. Unfortunately, decoupling
capacitors require a significant amount of area and efficient packaging solutions
must be leveraged to reduce chip area.
10.3.4
Latch-Based Clocking
While the use of registers in a sequential circuits enables a robust design methodology,
there are significant performance advantages to using a latch based design in which combinational logic is separated by transparent latches. In an edge-triggered system, the worst
case logic path between two registers determines the minimum clock period for the entire
system. If a logic block finishes before the clock period, it has to idle till the next input is
latched in on the next system clock edge. The use of a latch based methodology (as illustrated in Figure 10.26) enables more flexible timing, allowing one stage to pass slack to or
steal time from following stages. This flexibility, allows an overall performance increase.
Note that the latch based methodology is nothing more than adding logic between latches
of a master-slave flip-flop.
For the latch-based system in Figure 10.26, assume a two-phase clocking scheme.
Assume furthermore that the clock are ideal, and that the two clocks are inverted versions
of each other (for sake of simplicity). In this configuration, a stable input is available to
the combinational logic block A (CLB_A) on the falling edge of CLK1 (at edge ) and it
has a maximum time equal to the TCLK/2 to evaluate (that is, the entire low phase of
CLK1). On the falling edge of CLK2 (at edge ), the output CLB_A is latched and the
computation of CLK_B is launched. CLB_B computes on the low phase of CLK2 and the
output is available on the falling edge of CLK1 (at edge ). This timing appears equivalent to having an edge-triggered system where CLB_A and CLB_B are cascaded and
between two edge-triggered registers (Figure 10.27). In both cases, it appears that the time
available to perform the combination of CLB_A and CLB_B is TCLK.
2
3
4
chapter10_141.fm Page 65 Tuesday, April 16, 2002 9:12 AM
65
TIMING ISSUES IN DIGITAL CIRCUITS
In
L1
D
A
L2
CLB_A
tpd,A
Q
CLK1
B
Q
D
L1
CLB_B
tpd,B
D
CLK2
C
Chapter 10
L2
CLB_C
tpd,C
Q
D
CLK1
Q
CLK2
TCLK
1
CLK1
2
compute
CLB_A
3
CLK2
launch B
4
launch C
launch A
compute
CLB_B
Figure 10.26 Latch-based design in which transparent latches are separated by combinational logic.
However, there is an important performance related difference. In a latch based system, since the logic is separated by level sensitive latches, it possible for a logic block to
utilize time that is left over from the previous logic block and this is referred to as slack
borrowing [Bernstein00]. This approach requires no explicit design changes, as the passing of slack from one block to the next is automatic. The key advantage of slack borrowing is that it allows logic between cycle boundaries to use more than one clock cycle while
satisfying the cycle time constraint. Stated in another way, if the sequential system works
at a particular clock rate and the total logic delay for a complete cycle is larger than the
clock period, then unused time or slack has been implicitly borrowed from preceding
stages. This implies that the clock rate can be higher than the worst case critical path!
Slack passing happens due to the level sensitive nature of latches. In Figure 10.26,
the input to CLB_A should be valid by the falling edge of CLK1 (edge ). What happens
if the combinational logic block of the previous stage finishes early and has a valid input
data for CLB_A before edge ? Since the a latch is transparent during the entire high
phase of the clock, as soon as the previous stage has finished computing, the input data for
CLB_A is valid. This implies that the maximum time available for CLB_A is its phase time
(i.e., the low phase of CLK1) and any left over time from the previous computation. Formally state, slack passing has taken place if TCLK < tpd, A + tpd, B and the logic functions correctly (for simplicity, the delay associated with latches are ignored). An excellent
quantitative analysis of slack-borrowing is presented in [Bernstein00].
2
2
In
L1
D
L1
L2
Q
CLK1
D
Q
CLB_A
CLK2
CLB_B
D
L2
Q
CLK1
D
Q
CLB_C
CLK2
Figure 10.27 Edge-triggered pipeline (back-to-back latches for edge-triggered registers) of the logic in Figure
10.26.
Consider the latch based system in Figure 10.28. In this example, point a (input to
CLB_A) is valid before the edge . This implies that the previous block did not use up the
entire high phase of CLK1, which results in slack time (denoted by the shaded area). By
2
chapter10_141.fm Page 66 Tuesday, April 16, 2002 9:12 AM
Section 10.3
Synchronous Design — An In-depth Perspective
66
construction, CLB_A can start computing as soon as point a becomes valid and uses the
slack time to finish well before its allocated time (edge ). Since L2 is a transparent latch,
c becomes valid on the high phase of CLK2 and CLB_B starts to compute by using the
slack provided by CLB_A. CLB_B completes before its allocated time (edge ) and
passes a small slack to the next cycle. As this picture indicates, the total cycle delay, that is
the sum of the delay for CLB_A and CLB_B, is larger than the clock period. Since the
pipeline behaves correctly, slack passing has taken place and a higher throughput has been
achieved.
3
4
L1
In
D
Q
CLB_A
tpd,A
a
b
L2
D Q
CLB_B
tpd,B
c
L1
d
CLK2
CLK1
Q
D
e
CLK1
TCLK
CLK1
1
2
4
3
CLK2
slack passed to next stage
tpd,A
tDQ
tpd,B
tDQ
e valid
d valid
a valid
b valid c valid
Figure 10.28 Example of slack-borrowing.
An important question related to slack passing relates to the maximum possible
slack that can be passed across cycle boundaries. In Figure 10.28, it is easy that see that
the earliest time that CLB_A can start computing is . This happens if the previous logic
block did not use any of its allocated time (CLK1 high phase) or if it finished by using
slack from previous stages. Therefore, the maximum time that can be borrowed from
the previous stage is 1/2 cycle or TCLK /2. Similarly, CLB_B must finish its operation
by edge . This implies that the maximum logic cycle delay is equal to 1.5 * TCLK.
However, note that for an n-stage pipeline, the overall logic delay cannot exceed the
time available of n * TCLK.
1
4
Example 10.3 Slack-passing example
First consider an edge-triggered pipeline of Figure 10.29. Assume that the primary input
In is valid slightly after the rising edge of the clock. For this circuit, it is easy to see that
the minimum clock period required is 125ns. The latency is two clock cycles (actually, the
output is valid 2.5 cycles after the input settles). Note that for the first pipeline stage, 1/2
chapter10_141.fm Page 67 Tuesday, April 16, 2002 9:12 AM
67
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
cycle is wasted as the input data can only be latched in on the falling edge of the clock.
This time can be exploited in a latch based system.
a
In
D Q
CL1
b
75ns
CL2
c
d
D Q
50ns
CLK
CL3
e
CL4
75ns
f
50ns
CLK
Out
D Q
CLK
Figure 10.29 Conventional edge-triggered pipeline.
Figure 10.30 shows a latch based pipeline of the same sequential circuit. As the timing indicates, exactly the same timing can be achieve with a clock period of 100ns. This is
enabled by slack borrowing between logical partitions.
In
D Q
a
CL1
75ns
CLK
b
D Q
c
CL2
d
50ns
D Q
e
CL3
75ns
CLK
CLK
g
f
D Q
CL4
50ns
h
Out
D Q
CLK
CLK
TCLK = 100ns
CLK
tpd,CL1
a valid
tpd,CL2
b valid c valid d valid e valid
tpd,CL4
tpd,CL3
f valid g valid h valid Out valid
Figure 10.30 Latch-based pipeline.
10.4
Self-Timed Circuit Design*
10.4.1
Self-Timed Logic - An Asynchronous Technique
The synchronous design approach advocated in the previous sections assumes that all circuit events are orchestrated by a central clock. Those clocks have a dual function.
• They insure that the physical timing constraints are met. The next clock cycle can
only start when all logic transitions have settled and the system has come to a steady
state. This ensures that only legal logical values are applied in the next round of
computation. In short, clocks account for the worst case delays of logic gates,
sequential logic elements and the wiring.
• Clock events serve as a logical ordering mechanism for the global system events. A
clock provides a time base that determines what will happen and when. On every
chapter10_141.fm Page 68 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
68
clock transition, a number of operations are initiated that change the state of the
sequential network.
Consider the pipelined datapath of Figure 10.31. In this circuit, the data transitions
through logic stages under the command of the clock. The important point to note under
this methodology is that the clock period is chosen to be larger than the worst-case delay
of each pipeline stage, or T > max (tpd1, tpd2, tpd3) + tpd,reg. This will ensure satisfying the
physical constraint. At each clock transition, a new set of inputs is sampled and computation is started anew. The throughput of the system—which is equivalent to the number of
data samples processed per second—is equivalent to the clock rate. When to sample a new
input or when an output is available depends upon the logical ordering of the system
events and is clearly orchestrated by the clock in this example.
In
R1
D
CLK
Figure 10.31
Logic
Block #1
Q
tpd,reg
R2
D
Q
tpd1
Logic
Block #2
tpd2
R3
D
Q
Logic
Block #3
R4
D
Q
tpd3
Pipelined, synchronous datapath.
The synchronous design methodology has some clear advantages. It presents a
structured, deterministic approach to the problem of choreographing the myriad of events
that take place in digital designs. The approach taken is to equalize the delays of all operations by making them as bad as the worst of the set. The approach is robust and easy to
adhere to, which explains its enormous popularity; however it does have some pitfalls.
• It assumes that all clock events or timing references happen simultaneously over the
complete circuit. This is not the case in reality, because of effects such as clock skew
and jitter.
• As all the clocks in a circuit transitions at the same time, significant current flows
over a very short period of time (due to the large capacitance load). This causes significant noise problems due to package inductance and power supply grid resistance.
• The linking of physical and logical constraints has some obvious effects on the performance. For instance, the throughput rate of the pipelined system of Figure 10.31
is directly linked to the worst-case delay of the slowest element in the pipeline. On
the average, the delay of each pipeline stage is smaller. The same pipeline could
support an average throughput rate that is substantially higher than the synchronous
one. For example, the propagation delay of a 16-bit adder is highly data dependent
(e.g., adding two 4-bit numbers requires a much shorter time compared to adding
two 16-bit numbers).
One way to avoid these problems is to opt for an asynchronous design approach and
to eliminate all the clocks. Designing a purely asynchronous circuit is a nontrivial and
potentially hazardous task. Ensuring a correct circuit operation that avoids all potential
race conditions under any operation condition and input sequence requires a careful timing analysis of the network. In fact, the logical ordering of the events is dictated by the
structure of the transistor network and the relative delays of the signals. Enforcing timing
chapter10_141.fm Page 69 Tuesday, April 16, 2002 9:12 AM
69
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
constraints by manipulating the logic structure and the lengths of the signal paths requires
an extensive use of CAD tools, and is only recommended when strictly necessary.
A more reliable and robust technique is the self-timed approach, which presents a
local solution to the timing problem [Seitz80]. Figure 10.32 uses a pipelined datapath to
illustrate how this can be accomplished. This approach assumes that each combinational
function has a means of indicating that it has completed a computation for a particular
piece of data. The computation of a logic block is initiated by asserting a Start signal. The
combinational logic block computes on the input data and in a data-dependent fashion
(taking the physical constraints into account) generates a Done flag once the computation
is finished. Additionally, the operators must signal each other that they are either ready to
receive a next input word or that they have a legal data word at their outputs that is ready
for consumption. This signaling ensures the logical ordering of the events and can be
achieved with the aid of an extra Ack(nowledge) and Req(uest) signal. In the case of the
pipelined datapath, the scenario could proceed as follows.
Req
Req
HS
Ack
R1
HS
Ack
Start
In
Req
Done
F1
tpF1
HS
Ack
Start
R2
Req
Done
F2
tpF2
Ack
Start
R3
Done
F3
Out
tpF3
Figure 10.32 Self-timed, pipelined datapath.
1. An input word arrives, and a Req(uest) to the block F1 is raised. If F1 is inactive at
that time, it transfers the data and acknowledges this fact to the input buffer, which
can go ahead and fetch the next word.
2. F1 is enabled by raising the Start signal. After a certain amount of time, dependent
upon the data values, the Done signal goes high indicating the completion of the
computation.
3. A Re(quest) is issued to the F2 module. If this function is free, an Ack(nowledge) is
raised, the output value is transferred, and F1 can go ahead with its next computation.
The self-timed approach effectively separates the physical and logical ordering
functions implied in circuit timing. The completion signal Done ensures that the physical
timing constraints are met and that the circuit is in steady state before accepting a new
input. The logical ordering of the operations is ensured by the acknowledge-request
scheme, often called a handshaking protocol. Both interested parties synchronize with
each other by mutual agreement or, if you want, by shaking hands. The ordering protocol
described above and implemented in the module HS is only one of many that are possible.
The choice of protocol is important, since it has a profound effect on the circuit performance and robustness.
chapter10_141.fm Page 70 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
70
When compared to the synchronous approach, self-timed circuits display some
alluring properties.
• In contrast to the global centralized approach of the synchronous methodology, timing signals are generated locally. This avoids all problems and overheads associated
with distributing high-speed clocks.
• Separating the physical and logical ordering mechanisms results in a potential
increase in performance. In synchronous systems, the period of the clock has to be
stretched to accommodate the slowest path over all possible input sequences. In selftimed systems, a completed data-word does not have to wait for the arrival of the
next clock edge to proceed to the subsequent processing stages. Since circuit delays
are often dependent upon the actual data value, a self-timed circuit proceeds at the
average speed of the hardware in contrast to the worst-case model of synchronous
logic. For a ripple carry adder, the average length of carry-propagation is O(log
(N)). This is a fact that can be exploited in self-timed circuits, while in a synchronous methodology, a worst case performance that varies linearly with the number of
bits O(N)) must be assumed.
• The automatic shut-down of blocks that are not in use can result in power savings.
Additionally, the power consumption overhead of generating and distributing highspeed clocks can be partially avoided. As discussed earlier, this overhead can be
substantial. It is also possible to reduce the average clock load in synchronous processors through the use of gated clocks in which portions of the circuits that don’t
compute in a cycle are shut off.
• Self-timed circuits are by nature robust to variations in manufacturing and operating
conditions such as temperature. Synchronous systems are limited by their performance at the extremes of the operating conditions. The performance of a self-timed
system is determined by the actual operating conditions.
Unfortunately, these nice properties are not for free; they come at the expense of a
substantial circuit-level overhead, which is caused by the need to generate completion signals and the need for handshaking logic that acts as a local traffic agent to order the circuit
events (see block HS in Figure 10.32). Both of these topics are treated in more detail in
subsequent sections.
10.4.2
Completion-Signal Generation
A necessary component of self-timed logic is the circuitry to indicate when a particular
piece of circuitry has completed its operation for the current piece of data. There are two
common and reliable ways to generate the completion signal.
Dual-Rail Coding
One common approach to completion signal generation is the use of dual rail coding. It
actually requires the introduction of redundancy in the data representation to signal that a
particular bit is either in a transition or steady-state mode. Consider the redundant data
chapter10_141.fm Page 71 Tuesday, April 16, 2002 9:12 AM
71
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
model presented in Table 10.1. Two bits (B0 and B1) are used to represent a single data bit
B. For the data to be valid or the computation to be completed, the circuit must be in a
legal 0 (B0 = 0, B1 = 1) or 1 (B0 = 1, B1 = 0) state. The (B0 = 0, B1 = 0) condition signals
that the data is non-valid and the circuit is in either a reset or transition mode. The (B0 = 1,
B1 = 1) state is illegal and should never occur in an actual circuit.
Table 10.1
Redundant signal representation to include transition state.
B
B0
B1
in transition (or reset)
0
0
0
0
1
1
1
0
illegal
1
1
A circuit that actually implements such a redundant representation is shown in Figure 10.33, which is a dynamic version of the DCVSL logic style where the clock is
replaced by the Start signal [Heller84]. DCVSL uses a redundant data representation by
nature of its differential dual-rail structure. When the Start signal is low, the circuit is precharged by the PMOS transistors, and the output (B0, B1) goes in the Reset-Transition
state (0, 0). When the Start signal goes high, signaling the initiation of a computation, the
NMOS pull-down network evaluates, and one of the precharged nodes is lowered. Either
B0 or B1—but never both—goes high, which raises Done and signals the completion of
the computation.
VDD
VDD
Start
B0
B0
B1
In1
In1
In2
In2
PDN
Start
Done
B1
PDN
Figure 10.33 Generation of a
completion signal in DCVSL.
DCVSL is more expensive in terms of area than a non-redundant circuit due to its
dual nature. The completion generation is performed in series with the logic evaluation,
and its delay adds directly to the total delay of the logic block. The completion signals of
all the individual bits must be combined to generate the completion for an N-bit data word.
Completion generation thus comes at the expense of both area and speed. The benefits of
the dynamic timing generation often justify this overhead. Redundant signal presentations
other than the one presented in Table 10.1 can also be envisioned. One essential element is
the presence of a transition state denoting that the circuit is in evaluation mode and the
output data is not valid.
chapter10_141.fm Page 72 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
Example 10.4
72
Self-Timed Adder Circuit
An efficient implementation of a self-timed adder circuit is shown in Figure 10.34
[Abnous93]. A Manchester-carry scheme is used to boost the circuit performance. The proposed approach is based on the observation that the circuit delay of an adder is dominated by
the carry-propagation path. It is consequentially sufficient to use the differential signaling in
the carry path only (Figure 10.34a). The completion signal is efficiently derived by combining the carry signals of the different stages (Figure 10.34b). This safely assumes that the sum
generation, which depends upon the arrival of the carry signal, is faster than the completion
generation. The benefit of this approach is that the completion generation starts earlier and
proceeds in parallel with sum generation, which reduces the critical timing path. All other signals such as P(ropagate), G(enerate), K(ill), and S(um) do not require completion generation
and can be implemented in single-ended logic. As shown in the circuit schematics, the differential carry paths are virtually identical. The only difference is that the G(enerate) signal is
replaced by a K(ill). A simple logic analysis demonstrates that this indeed results in an
inverted carry signal and, hence, a differential signaling.
VDD
Start
P0
C0
P1
P2
C0
G0
G1
G2
C2out
C1out
Start
P3
C3
C2
C1
C4
C4
G3
C3out
C4out
VDD
Start
VDD
Start
P0
C0
P1
C1
C0
K0
C2
K1
C1out
Start
P2
P3
C3
K2
C2out
C4
C4
K3
C3out
C4out
C 4out
C3out
C3out
C2out
C2out
C1out
C1out
C4out
(a) Differential carry generation
Figure 10.34
Done
Start
(b) Completion signal
Manchester-carry scheme with differential signal representation.
Replica Delay
While the dual-rail coding above allows tracking of the signal statistics, it comes at the
cost of power dissipation. Every single gate must transition for every new input vector,
regardless of the value of the data vector. An attempt to reduce the overhead of completion
detection is to use a critical-path replica configured as a delay element, as shown in Figure
chapter10_141.fm Page 73 Tuesday, April 16, 2002 9:12 AM
73
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
10.35. To start a computation, the Start signal is raised and the computation of the logic
network is initiated. At the same time, the start signal is fed into the replica delay line,
which tracks the critical path of the logic network. It is important that the replica is structured such that no glitching transitions occur. When the output of the delay line makes a
transition, it indicates that the logic is complete—as the delay line mimics the critical path.
In general, it is important to add extra padding in the delay line to compensate for possible
random process variations. The advantage of this approach is that the logic can be implemented using a standard non-redundant circuit style such as complementary CMOS. Also,
if multiple logic units are computing in parallel, it is possible to amortize the overhead of
the delay line over multiple blocks. Note that this approach generates the completion signal after a time equal to the worst case delay through the network. As a result, it does not
exploit the statistical properties of the incoming data. However, it can track the local
effects of process variations and environmental variations (e.g., temperature or power supply variations). This approach is widely used to generate the internal timing of semiconductor memories where self-timing is a commonly used technique.
In
LOGIC
NETWORK
Start
DELAY MODULE
(CRITICAL PATH REPLICA)
Out
Done
Figure 10.35 Completion-signal gener
using delay module.
Example 10.5An alternate completion detection circuit using current sensing
Ideally, logic should be implemented using non-redundant CMOS (e.g., static CMOS) and
the completion signal circuitry should track data dependencies. Figure 10.36 shown an
example technique that attempts to realize the above [REF]. A current sensor is inserted in
series with the combinational logic, and monitors the current flowing through the logic.
The current sensor outputs a low value when no current flows through the logic (this is,
the logic is idle), and is high when the combinational logic is switching performing computation. This signal effectively determines when the logic has completed its cycle. Note
that this approach tracks data-dependent computation times — if only the lower order bits
of an adder switch, current will stop flowing once the lower order bits switch to the final
value.
If the input data vector does not change from one cycle to the next, no current is
drawn from the supply for static CMOS logic. In this case, a delay element that tracks the
minimum delay through the logic and current sensor is used for signal completion. The
outputs of the current sensor and minimum delay element are then combined. This
approach is interesting, but requires careful analog design. Ensuring reliability while
keeping the overhead circuitry small is the main challenge. These concerns have kept the
applicability of the approach very limited, notwithstanding its great potential.
chapter10_141.fm Page 74 Tuesday, April 16, 2002 9:12 AM
Self-Timed Circuit Design*
Inputs
74
VDD
Input Register
Section 10.4
Start
tdelay
Output
Static CMOS Logic
A
GNDsense
Start
Current Sensor
toverlap
A
B
tMDG
Done
Min Delay Generator
tpd-NOR
Done
B
Output
tMDG > min(tdelay)
Figure 10.36
10.4.3
⇒t
valid
overlap
>0
Completion-signal generation using current sensing.
Self-Timed Signaling
Besides the generation of the completion signals, a self-timed approach also requires a
handshaking protocol to logically order the circuit events avoiding races and hazards. The
functionality of the signaling (or handshaking) logic is illustrated by the example of Figure 10.37, which shows a sender module transmitting data to a receiver ([Sutherland89]).
Req
2
Req
Ack
SENDER
Data
3
RECEIVER
Ack
(a) Sender-receiver configuration
Data
1
1
cycle 1
cycle 2
Sender’s action
Figure 10.37
Receiver’s action
Two-phase handshaking protocol.
(b) Timing diagram
1
The sender places the data value on the data bus
and produces an event on the Req
control signal by changing the polarity of the signal . In some cases the request event is
a rising transition; at other times it is a falling one—the protocol described here does not
distinguish between them. Upon receiving the request, the receiver accepts the data when
possible and produces an event on the Ack signal to indicate that the data has been
accepted . If the receiver is busy or its input buffer is full, no Ack event is generated, and
the transmitter is stalled until the receiver becomes available by, for instance, freeing
space in the input buffer. Once the Ack event is produced, the transmitter goes ahead and
produces the next data word . The four events, data change, request, data acceptance,
3
1
2
chapter10_141.fm Page 75 Tuesday, April 16, 2002 9:12 AM
75
TIMING ISSUES IN DIGITAL CIRCUITS
A
F
C
B
A
B
Fn+1
0
0
1
0
1
0
0
Fn
Fn
1
1
1
(a) Schematic
Figure 10.38
Chapter 10
Muller C-element.
(b) Truth table
and acknowledge, proceed in a cyclic order. Successive cycles may take different amounts
of time depending upon the time it takes to produce or consume the data.
This protocol is called two-phase, since only two phases of operation can be distinguished for each data transmission—the active cycle of the sender and the active cycle of
the receiver. Both phases are terminated by certain events. The Req event terminates the
active cycle of the sender, while the receiver’s cycle is completed by the Ack event. The
sender is free to change the data during its active cycle. Once the Req event is generated, it
has to keep the data constant as long as the receiver is active. The receiver can only accept
data during its active cycle.
The correct operation of the sender-receiver system requires a strict ordering of the
signaling events, as indicated by the arrows in Figure 10.37. Imposing this order is the task
of the handshaking logic which, in a sense, performs logic manipulations on events. An
essential component of virtually any handshaking module is the Muller C-element. This
gate, whose schematic symbol and truth table are given in Figure 10.38, performs an
AND-operation on events. The output of the C-element is a copy of its inputs when both
inputs are identical. When the inputs differ, the output retains its previous value. Phrased
in a different way—events must occur at both inputs of a Muller C-element for its output
to change state and to create an output event. As long as this does not happen, the output
remains unchanged and no output event is generated. The implementation of a C-element
is centered around a flip-flop, which should be of no surprise, given the similarities in
their truth tables. Figure 10.39 displays two potential circuit realizations—a static and a
dynamic one respectively.
VDD
VDD
B
A
A
S
B
R
Q
A
F B
B
Figure 10.39
F
F
B
A
(a) Logic
VDD
(b) Majority Function
B
(c) Dynamic
Implementations of a Muller C-element.
Figure 10.40 shows how to use this component to enforce the two-phase handshaking protocol for the example of the sender-receiver. Assume that Req, Ack, and Data
Ready are initially 0. When the sender wants to transmit the next word, the Data Ready
signal is set to 1, which triggers the C-element because both its inputs are at 1. Req goes
chapter10_141.fm Page 76 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
76
high—this is commonly denoted as Req↑. The sender now resides in the wait mode, and
control is passed to the receiver. The C-element is blocked, and no new data is sent to
the data bus (Req stays high) as long as the transmitted data is not processed by the
receiver. Once this happens, the Data accepted signal is raised. This can be the result
of many different actions, possibly involving other C-elements communicating with
subsequent blocks. An Ack↑ ensues, which unblocks the C-element and passes the
control back to the sender. A Data ready↓ event, which might already have happened
before Ack↑, produces a Req↓, and the cycle is repeated.
Data
Sender
logic
Receiver
logic
Data ready
Data accepted
Req
C
Figure 10.40 A Muller C-element
implements a two-phase handshake
protocol. The circle at the lower input
of the Muller C-element stands for
inversion.
Ack
Handshake logic
Problem 10.1 Two-Phase Self-Timed FIFO
Figure 10.41 shows a two-phase, self-timed implementation of a FIFO (first-in first-out)
buffer with three registers. Assuming that the registers accept a data word on both positiveand negative-going transitions of the En signals and that the Done signal is simply a delayed
version of En, examine the operation of the FIFO by plotting the timing behavior of all signals of interest. How can you observe that the FIFO is completely empty (full)? (Hint: Determine the necessary conditions on the Ack and Req signals.)
Out
In
R1
En
R2
R3
Done
Reqi
Req0
C
Acki
C
C
Acko
Figure 10.41 Three-stage
self-timed FIFO, using a twophase signaling protocol.
The two-phase protocol has the advantage of being simple and fast. There is some
bad news, however. This protocol requires the detection of transitions that may occur in
either direction. Most logic devices in the MOS technology tend to be sensitive to levels or
to transitions in one particular direction. Event-triggered logic, as required in the twophase protocol, requires extra logic as well as state information in the registers and the
computational elements. Since the transition direction is important, initializing all the
Muller C-elements in the appropriate state is essential. If this is not done, the circuit might
dead-lock, which means that all elements are permanently blocked and nothing will ever
chapter10_141.fm Page 77 Tuesday, April 16, 2002 9:12 AM
77
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
happen. A detailed study on how to implement event-triggered logic can be found in the
text by Sutherland on micropipelines [Sutherland89].
The only alternative is to adopt a different signaling approach, called four-phase signaling, or return-to-zero (RTZ). This class of signaling requires that all controlling signals
be brought back to their initial values before the next cycle can be initiated. Once again,
this is illustrated with the example of the sender-receiver. The four-phase protocol for this
example is shown in Figure 10.42.
4
2
Req
Sender’s action
Receiver’s action
Ack
5
3
Data
1
1
Cycle 1
Cycle 2
Figure 10.42 Four-phase
handshaking protocol.
The protocol presented is initially the same as the two-phase one. Both the Req and
the Ack are initially in the zero-state, however. Once a new data word is put on the bus ,
the Req is raised (Req↑ or ) and control is passed to the receiver. When ready, the
receiver accepts the data and raises Ack (Ack↑ or ). So far, nothing new. The protocol
proceeds, now by bringing both Req (Req↓ or ) and Ack (Ack↓ or ) back to their initial
state in sequence. Only when that state is reached is the sender allowed to put new data on
the bus . This protocol is called four-phase because four distinct time-zones can be recognized per cycle: two for the sender; two for the receiver. The first two phases are identical to the two-phase protocol; the last two are devoted to resetting of the state. An
implementation of the protocol, based on Muller C-elements, is shown in Figure 10.43. It
is interesting to notice that the four-phase protocol requires two C-elements in series
(since four states must be represented). The Data ready and Data accepted signals must be
pulses instead of single transitions.
1
2
4
3
5
1
Data
Sender
Receiver
logic
logic
Data accepted
Data ready
S
C
Req
C
Ack
Handshake logic
Figure 10.43 Implementation of 4-phase handshake protocol using Muller C-elements.
chapter10_141.fm Page 78 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
Problem 10.2
78
Four-Phase Protocol
Derive the timing diagram for the signals shown in Figure 10.43. Assume that the Data Ready
signal is a pulse and that the Data Accepted signal is a delayed version of Req.
The four-phase protocol has the disadvantage of being more complex and slower,
since two events on Req and Ack are needed per transmission. On the other hand, it has the
advantage of being robust. The logic in the sender and receiver modules does not have to
deal with transitions, which can go either way, but only has to consider rising (or falling)
transition events or signal levels. This is readily accomplished with traditional logic circuits.
For this reason, four-phase handshakes are the preferred implementation approach for most
of the current self-timed circuits. The two-phase protocol is mostly selected when the
sender and receiver are far apart and the delays on the control wires (Ack, Req) are
substantial.
Example 10.6
The Pipelined Datapath—Revisited
We have introduced both the signaling conventions and the concepts of the completion-signal
generation. Now it is time to bring them all together. We do this with the example of the pipelined data path, which was presented earlier. A view of the self-timed data path, including the
timing control, is offered in Figure 10.44. The logic functions F1 and F2 are implemented
using dual-rail, differential logic.
In
Out
R1
F1
Start
En
Reqi
R2
Done
F2
Start
En
Reqo
Reqint
C
C
C
Ackint
Acki
Figure 10.44
Done
C
Acko
Self-timed pipelined datapath—complete composition.
To understand the operation of this circuit, assume that all Req and Ack signals, including the internal ones, are set to 0, what means there is no activity in the data path. All Start
signals are low so that all logic circuits are in precharge condition. An input request (Reqi↑)
triggers the first C-element. The enable signal En of R1 is raised, effectively latching the input
data into the register, assuming a positive edge-triggered or a level-sensitive implementation.
Acki↑ acknowledges the acceptance of the data. The second C-element is triggered as well,
since Ackint is low. This raises the Start signal and starts the evaluation of F1. At its completion, the output data is placed on the bus, and a request is initiated to the second stage
(Reqint↑), which acknowledges its acceptance by raising Ackint.
At this point, stage 1 is still blocked for further computations. However, the input
buffer can respond to the Acki↑ event by resetting Reqi to its zero state (Reqi↓). In turn, this
lowers En and Acki. Upon receival of Ackint↑, Start goes low, the pre-charge phase starts, and
chapter10_141.fm Page 79 Tuesday, April 16, 2002 9:12 AM
79
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
F1 is ready for new data. Note that this sequence corresponds to the four-phase handshake
mechanism described earlier. The dependencies among the events are presented in a more
pictorial fashion in the state transition diagram (STG) shown in Figure 10.45. These STGs
can become very complex. Computer tools are often used to derive STGs that ensure proper
operation and optimize the performance.
Reqi↑
Start↑
Reqint↑
Acki↑
Ackint↑
Reqi↓
Start↓
Reqint↓
Acki↓
C-element 1
Ackint↓
C-element 2
Figure 10.45 State transition diagram for pipeline stage 1. The nodes represent the signaling events,
while the arrows express dependencies. Arrows in dashed lines express actions in either the preceding or
following stage.
10.4.4
Practical Examples of Self-Timed Logic
As described in the previous section, self-timed circuits can provide significant performance advantage. Unfortunately, the overhead circuits preclude widespread application in
general purpose digital computing. However, several applications exist that exploit the
key concepts of self-timed circuits. A few examples that illustrate the use of self-timed
concepts for either power savings or performance enhancement are presented below.
Glitch Reduction Using Self-timing
A major source of unnecessary switched capacitance in a large datapath such as bit-sliced
adders and multipliers, is due to spurious transitions caused by glitch propagation. Imbalances in a logic network cause inputs of a logic gate or block to arrive at different times,
resulting in glitching transitions. In large combinational blocks such as multipliers, transitions happens in waves as the primary input changes ripple through the logic. If a logic
block can be enabled after all of the inputs settle, then the number of glitching transitions
can be reduced. One approach for minimizing spurious transitions is the use of a selftimed gating approach that involves partitioning each computational logic block into
smaller blocks and distinct phases. Tri-state buffers are inserted between each of these
phases to prevent glitches from propagating further in the datapath (Figure 10.46). Assuming an arbitrary logic network in Figure 10.46, the outputs of logic block 1 will not be synchronized. When the tri-state buffers at the output of logic block 1 are enabled, the the
computation of logic block 2 is allowed to proceed. To reduce glitching transitions, the tristate buffer should be enabled only when the outputs of logic block 1 are ensured to be stable and valid. The control of the tri-state buffer can be performed through the use of a selftimed enable signal which is generated by passing the system clock through a delay chain
chapter10_141.fm Page 80 Tuesday, April 16, 2002 9:12 AM
Section 10.4
Self-Timed Circuit Design*
80
that models the critical path of the processor. The delay chain is then tapped at the points
corresponding to the locations of the buffers, and the resulting signals are distributed
throughout the chip. This technique succeeds in reducing the switched capacitance combinational logic blocks such as multipliers, even including the overhead of the delay chain,
gating signal distribution and buffers [Goodman98].
Logic
out1
CLK
delay chain
...
in2
Logic
out2
in3
Block 2
Block 1
CLKD1
Logic
Block 3
CLKD2
..
CLK
out1
in2
out2
in3
Figure 10.46 Application of self-timing for glitch reduction.
Post-Charge Logic
An interesting form of self-timed logic is self-resetting CMOS. This structure uses a different control structure than the conventional self-timed pipeline described earlier. The
idea is that instead of checking if all of the logic blocks have completed their operation
before transitioning to the reset stage, the idea is to precharge a logic block as soon as it
completes it operation. Since the precharge happens after operation instead of before evaluation, it is often termed post-charge logic. A block diagram of post-charge logic is shown
in Figure 10.47 [Williams00]. As seen from this block diagram, the precharging of L1
Precharged
Logic Block
(L1)
completion
detection
(L3)
completion
detection
(L2)
completion
detection
(L1)
Precharged
Logic Block
(L2)
Precharged
Logic Block
(L3)
Figure 10.47 Self-resetting logic.
happen when the successor stage has finished evaluating. It is possible to precharge a
block based on the completion of its own output, but care must be taken to ensure that the
following stage has properly evaluated based on the output before it is precharged.
chapter10_141.fm Page 81 Tuesday, April 16, 2002 9:12 AM
81
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
It should be noted that unlike other logic
VDD
styles, the signals are represented as pulses, and are
valid only for a limited duration. The pulse width
must be shorter than the reset delay or else, there
int
would be a contention between the precharge
A
B
out
C
device and the evaluate switches. While this logic
style offers potential speed advantages, special care
Figure 10.48 Self-resetting
must be taken to ensure correct timing. Also, cir3-input OR.
cuitry that converts level signals to pulses are
required. An example of self-resetting logic is
shown in Figure 10.48 [Bernstein98]. Assume that all inputs are low, and int is initially
precharged. If A goes high, int will fall, causing out to go high. This causes, the gate to
precharge. When the PMOS precharge device is active, the inputs must be in a reset state
to avoid contention.
Clock-Delayed Domino
One interesting application of self-timed circuits using the delay-matching concept is
Clock-Delayed Domino. This is a style of dynamic logic, where there is no global clock
signal. Instead, the clock for one stage is derived from the previous stage. A block diagram
of this is shown in Figure 10.49. The two inverter delays along the clock path emulate the
worst case delay through the logic path (i.e., the Pulldown Network). Sometimes, there is
a transmission gate inserted between the two inverters to accomplish this (the transmission
gate is on with the gate terminal of NMOS tied to VDD and the PMOS to GND). Clockdelayed Domino was used in the IBM’s 1GHz Microprocessor and is used widely in high
speed Domino logic. There are several advantages of using such a self-clocked timing
abstraction. First, CD domino can provide both inverting and non-inverting function. This
alleviates a major limitation of conventional Domino that is only capable of non-inverting
logic. The inverter after the pulldown network is not essential as the clock arrives to the
next stage only after the current stage has evaluated. Also, notice that is possible to eliminate the “foot-switch” in the later stages, as the clock-evaluation edge arrives only when
the input is stable. This provides significant speed up of the logic critical path. A careful
analysis of the timing shows that the short circuit power can be eliminated.
CLK1
D1
CLK3
CLK2
Pulldown
Network
Evaluate occurs
D2
Pulldown
Network
D3
CLK4
Pulldown
Network
D4
Pulldown
Network
Out
Precharge occurs
C1
C2
C3
C4
Phase2 Clk1
Slow
Figure 10.49 Clock Delayed Domino Logic. A
self-clocked logic style
chapter10_141.fm Page 82 Tuesday, April 16, 2002 9:12 AM
Section 10.5
10.5
Synchronizers and Arbiters*
82
Synchronizers and Arbiters*
10.5.1
Synchronizers—Concept and Implementation
Even though a complete system may be designed in a synchronous fashion, it must still
communicate with the outside world, which is generally asynchronous. An asynchronous
input can change value at any time related to the clock edges of the synchronous system,
as is illustrated in Figure 10.50.
fin
Synchronous system
Asynchronous
system
fCLK
Synchronization
Figure 10.50 Asynchronous-synchronous interface
Consider a typical personal computer. All operations within the system are strictly
orchestrated by a central clock that provides a time reference. This reference determines
what happens within the computer system at any point in time. This synchronous computer has to communicate with a human through the mouse or the keyboard, who has no
knowledge of this time reference and might decide to press a keyboard key at any point in
time. The way a synchronous system deals with such an asynchronous signal is to sample
or poll it at regular intervals and to check its value. If the sampling rate is high enough, no
transitions will be missed—this is known as the Nyquist criterion in the communication
community. However, it might happen that the signal is polled in the middle of a transition. The resulting value is neither low or high but undefined. At that point, it is not clear
if the key was pressed or not. Feeding the undefined signal into the computer could be the
source of all types of trouble, especially when it is routed to different functions or gates
that might interpret it differently. For instance, one function might decide that the key is
pushed and start a certain action, while another function might lean the other way and
issue a competing command. This results in a conflict and a potential crash. Therefore, the
undefined state must be resolved in one way or another before it is interpreted further. It
does not really matter what decision is made, as long as a unique result is available. For
instance, it is either decided that the key is not yet pressed, which will be corrected in the
next poll of the keyboard, or it is concluded that the key is already pressed.
Thus, an asynchronous signal must be resolved to be either in the high or low state
before it is fed into the synchronous environment. A circuit that implements such a decision-making function is called a synchronizer. Now comes the bad news—building a perfect synchronizer that always delivers a legal answer is impossible! [Chaney73,
Glasser85] A synchronizer needs some time to come to a decision, and in certain cases this
time might be arbitrarily long. An asynchronous/synchronous interface is thus always prone
to errors called synchronization failures. The designer’s task is to ensure that the probability
of such a failure is small enough that it is not likely to disturb the normal system behavior.
Typically, this probability can be reduced in an exponential fashion by waiting longer before
chapter10_141.fm Page 83 Tuesday, April 16, 2002 9:12 AM
83
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
making a decision. This is not too troublesome in the keyboard example, but in general,
waiting affects system performance and should therefore be avoided to a maximal extent.
To illustrate why waiting helps reduce the
CLK
failure rate of a synchronizer, consider a synchroint
nizer as shown in Figure 10.51. This circuit is a
Q
I1
D
latch that is transparent during the low phase of
the clock and samples the input on the rising
I2
edge of the clock CLK. However, since the samCLK
pled signal is not synchronized to the clock sig- Figure 10.51 A simple synchronizer.
nal, there is a finite probability that the set-up
time or hold time of the latch is violated (the probability is a strong function of the transition frequencies of the input and the clock). As a result, one the clock goes high, there is a
the chance that the output of the latch resides somewhere in the undefined transition zone.
The sampled signal eventually evolves into a legal 0 or 1 even in the latter case, as the
latch has only two stable states.
Example 10.7
Flip-Flop Trajectories
Figure 10.52 shows the simulated trajectories of the output nodes of a cross-coupled static
CMOS inverter pair for an initial state close to the metastable point. The inverters are composed of minimum-size devices.
2.0
Vout
Figure 10.52 Simulated trajectory for a
simple flip-flop synchronizer.
1.0
0.0
0
100
200
300
time, ps
If the input is sampled such that cross-coupled inverter starts at the metastable point,
the voltage will remain at the metastable state forever in the absense of noise. If the data is
sampled with a small offset (positive or negative), the differential voltage will evolve in an
exponential form, with a time constant that is dependent on the strength of the transistor as
well as the parasitic capacitances. The time it takes to reach the acceptable signal zones
depends upon the initial distance of the sampled signal from the metastable point.
In order to determine the required waiting period, let us build a mathematical model
of the behavior of the bistable element and use the results to determine the probability of
synchronization failure as a function of the waiting period. This model is used to compute
the range of values for v(0) that still cause an error, or a voltage in the undefined range,
after a waiting period T. A signal is called undefined if its value is situated between VIH
and VIL.
chapter10_141.fm Page 84 Tuesday, April 16, 2002 9:12 AM
Section 10.5
Synchronizers and Arbiters*
84
V MS – ( V MS – V IL )e – T / τ ≤ v ( 0 ) ≤ V MS + ( V IH – V MS )e – T / τ
(10.8)
Eq. (10.8) conveys an important message: The range of input voltages that cause a
synchronization error decreases exponentially with the waiting period T. Increasing the
waiting period from 2τ to 4τ decreases the interval and the chances of an error by a factor
of 7.4.
Some information about the asynchronous signal is required in order to compute the
probability of an error. Assume that Vin is a periodical waveform with an average period
Tsignal between transitions and with identical rise and fall times tr. Assume also that the
slopes of the waveform in the undefined region can be approximated by a linear function
(Figure 10.53). Using this model, we can estimate the probability Pinit that v(0), the value
of Vin at the sampling time, resides in the undefined region.
V
–V
IH
IL
--------------------- tr
V
swing
P init = -------------------------------T signal
(10.9)
The chances for a synchronization error to occur depend upon the frequency of the
synchronizing clock φ. The more sampling events, the higher the chance of running into
an error. This means that the average number of synchronization errors per second Nsync(0)
equals Eq. (10.10) if no synchronizer is used.
P init
N sync ( 0 ) = --------Tφ
(10.10)
where Tφ is the sampling period.
From Eq. (10.8) we learned that waiting a time T before observing the output
reduces exponentially the probability that the signal is still undefined.
P i ni t e –T / τ
( V IH – V IL )e – T / τ
tr
N sync ( T ) = ---------------------- = --------------------------------------- --------------------Tsignal T φ
Tφ
V swing
(10.11)
The robustness of an asynchronous-synchronous interface is determined by the following parameters: signal switching rate and rise time, sampling frequency, and waiting
time T.
Example 10.8
Synchronizers and Mean Time-to-Failure
Consider the following design example. Tφ = 5 nsec, which corresponds to a 200 Mhz clock), T
= Tφ = 5 nsec, Tsignal = 50 nsec, tr =0.5 nsec, and τ = 150 psec (as obtained in Example 10.7).
VIH – VIL
Vswing
(VIH – VIL) tr / Vswing
tr
Figure 10.53
signal slope.
Linear approximation of
chapter10_141.fm Page 85 Tuesday, April 16, 2002 9:12 AM
85
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
From the VTC of a typical CMOS inverter, it can be derived that VIH – VIL approximately
equals 0.5 V for a voltage swing of 2.5 V. Evaluation of Eq. (10.11) yields an error probability
of 1.38x 10–9 errors/sec. The inverse of Nsync is called the mean time-to-failure, or the MTF, and
equals 7 × 108sec, or 23 years. If no synchronizer was used, the MTF would only have been 2.5
µsec!
Design Consideration
When designing a synchronous/asynchronous interface, we must keep in mind the following
observations:
• The acceptable failure rate of a system depends upon many economic and social factors
and is a strong function of its application area.
• The exponential relation in Eq. (10.11) makes the failure rate extremely sensitive to the
value of τ. Defining a precise value of τ is not easy in the first place. τ varies from chip to
chip and is a function of temperature as well. The probability of an error occurring can
thus fluctuate over large ranges even for the same design. A worst-case design scenario is
definitely advocated here. If the worst-case failure rate exceeds a certain criterion, it can
be reduced by increasing the value of T. A problem occurs when T exceeds the sampling
period Tφ. This can be avoided by cascading (or pipelining) a number of synchronizers,
as shown in Figure 10.54. Each of those synchronizers has a waiting period equal to Tφ.
Notice that this arrangement requires the φ-pulse to be short enough to avoid race conditions. The global waiting period equals the sum of the Ts of all the individual synchronizers. The increase in MTF comes at the expense of an increased latency.
In
O1
Sync
φ
Figure 10.54
O2
Sync
Out
Sync
Cascading synchronizers reduces the main time-to-failure.
• Synchronization errors are very hard to trace due to their probabilistic nature. Making
the mean time-to-failure very large does not preclude errors. The number of synchronizers in a system should therefore be severely restricted. A maximum of one or two per
system is advocated.
10.5.2
Arbiters
Finally, a sibling of the synchronizer called the arbiter, interlock element, or mutualexclusion circuit, should be mentioned. An arbiter is an element that decides which of
two events has occurred first. Such components for instance allow multiple processors to
access a single resource, such as a large shared memory. A synchronizer is actually a
chapter10_141.fm Page 86 Tuesday, April 16, 2002 9:12 AM
Section 10.6
Clock Synthesis and Synchronization Using a Phase-Locked Loop
86
special case of an arbiter, since it determines if a signal transition happened before or
after a clock event. A synchronizer is thus an arbiter with one of its inputs tied to the
clock.
An example of a mutual-exclusion circuit is shown in Figure 10.55. It operates on
two input-request signals, that operate on a four-phase signaling protocol; that is, the
Req(uest) signal has to go back to the reset state before a new Req(uest) can be issued. The
output consists of two Ack(nowledge) signals that should be mutually exclusive. While
Requests may occur concurrently, only one of the Acknowledges is allowed to go high.
The operation is most easily visualized starting with both inputs low—neither device issuing a request—nodes A and B high, and both Acknowledges low. An event on one of the
inputs (e.g., Req1↑) causes the flip-flop to switch, node A goes low, and Ack1↑. Concurrent events on both inputs force the flip-flop into the metastable state, and the signals A
and B might be undefined for a while. The cross-coupled output structure keeps the output
values low until one of the NAND outputs differs from the other by more than a threshold
value VT. This approach eliminates glitches at the output.
Req1
Ack1
Req1
Arbiter
Req2
A
Ack2
Ack1
B
Ack2
Req2
(a) Schematic symbol
Req1
(b) Implementation
Req2
VT gap
A
B
Metastable
Ack1
t
(c) Timing diagram
Figure 10.55
10.6
Mutual-exclusion element (or arbiter).
Clock Synthesis and Synchronization Using a Phase-Locked Loop
There are numerous digital applications that require the on-chip generation of a periodic
signal. Synchronous circuits need a global periodic clock reference to drive sequential elements. Current microprocessors and high performance digital circuits require clock frequencies in the gigahertz range. Crystal oscillators generate accurate, low-jitter clocks
with a frequency range from 10’s of Megahertz to approximately 200MHz. To generate a
higher frequency required by digital circuits, a phase-locked loop (PLL) structure is typically used. A PLL takes an external low-frequency reference crystal frequency signal and
multiplies its frequency by a rational number N (see the left side of Figure 10.56).
chapter10_141.fm Page 87 Tuesday, April 16, 2002 9:12 AM
87
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
PLLs are also used to perform synchronization of communication between chips.
Typically as shown in Figure 10.56, a reference clock is sent along with the parallel data
being communicated (in this example only the transmit path from chip 1 to chip 2 is
shown). Since chip-to-chip communication occurs at a lower rate than the on-chip clock
rate, the reference clock is a divided but in-phase version of the system clock. The reference clock synchronizes all input flip-flops on chip 2; this can present a significant clock
load for wide data busses. Introducing clock buffers to deal with this problem unfortunately introduces skew between the data and sample clock. A PLL, using feedback, can be
align (i.e., de-skew) the output of the clock buffer with respect to the data. In addition, for
the configuration shown in Figure 10.56, the PLL can multiply the frequency of the
incoming reference clock, allowing the reference clock to be a fraction of the data rate.
Chip 1
Chip 2
Data
Digital
System
Digital
System
fsystem = N * fcrystal
Divider
reference
clock
PLL
PLL
Clock
Buffer
fcrystal < 200Mhz
Crystal
Oscillator
Figure 10.56Applications of Phase Locked Loops (PLL).
10.6.1
Basic Concept
Periodic signals of known frequency can be discribed exactly by only one parameter, their
phase. More accurately a set of two or more periodic signals of the same frequency can be
well defined if we know one of them and its phase with respect to the other signals, as in
Figure 10.57.Here φ1and φ2 represent the phase of the two signals. The relative phase is
defined as the difference between the two phases.
S
1
S
2
Time
φ 1 φ2
∆φ = φ 2 – φ 1
Figure 10.57Relative and absolute phase of two periodic signals
chapter10_141.fm Page 88 Tuesday, April 16, 2002 9:12 AM
Section 10.6
Clock Synthesis and Synchronization Using a Phase-Locked Loop
88
A PLL is a complex, nonlinear feedback circuit, and its basic operation is understood with the aid of Figure 10.58 [Jeong87]. The voltage-controlled oscillator (VCO)
takes an analog control input and generates a clock signal of the desired frequency. In general, there is a non-linear relationship between the control voltage (vcont) and the output
frequency. To synthesize a system clock of a particular frequency, it necessary to set the
control voltage to the appropriate value. This is function of the rest of the blocks (i.e.,
feedback loop) in the PLL. The feedback loop is critical to tracking process and environmental variations. The feedback also allows frequency multiplication.
The reference clock is typically generated off-chip from an accurate crystal reference. The reference clock is compared to a divided version of the system clock (i.e., the
local clock). The local clock and reference clock are compared using a phase detector that
compares the phase difference between the signals and produces an Up or Down signal
when the local clock lags or leads the reference signal. It detects which of the two input
signals arrives earlier and produces an appropriate output signal. Next, the Up and Down
signals are fed into a charge pump, which translates the digital encoded control information into an analog voltage [Gardner80]. An Up signal increases the value of the control
voltage and speeds up the VCO, which causes the local signal to catch up with the reference clock. A Down signal, on the other hand, slows down the oscillator and eliminates
the phase lead of the local clock.
Passing the output of the charge pump directly into the VCO creates a jittery clock
signal. The edge of the local clock jumps back and forth instantaneously and oscillates
around the targeted position. As discussed earlier, clock jitter, is highly undesirable, since
it reduces the time available for logic computation and therefore should be kept within a
given percentage of the clock period. This is partially accomplished by the introduction of
the loop filter. This low-pass filter removes the high-frequency components from the VCO
control voltage and smooths out its response, which results in a reduction of the jitter.
Note that the PLL structure is a feedback structure and the addition of extra phase shifts,
as is done by a high-order filter, may result in instability. Important properties of a PLL are
its lock range—the range of input frequencies over which the loop can maintain functionality; the lock time—the time it takes for the PLL to lock onto a given input signal; and the
jitter. When in lock, the system clock is N-times the reference clock frequency.
A PLL is an analog circuit and is inherently sensitive to noise and interference. This is
especially true for the loop filter and VCO, where induced noise has a direct effect on the
resulting clock jitter. A major source of interference is the noise coupling through the supply
Reference
clock
Local
clock
Up
Loop
filter
Charge
pump
Phase
detector
VCO
Down
Divide by
N
Figure 10.58
vcont
Composition of a phase-locked loop (PLL).
System
Clock
chapter10_141.fm Page 89 Tuesday, April 16, 2002 9:12 AM
89
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
rails and the substrate. This is particularly a concern in digital environments, where noise is
introduced due to a variety of sources. Analog circuits with a high supply rejection, such as
differential VCOs, are therefore desirable [Kim90]. In summary, integrating a highly sensitive component into a hostile digital environment is nontrivial and requires expert analog
design. Below a more detailed description of various components of a PLL is given.
10.6.2
Building Blocks of a PLL
Voltage Controlled Oscillator (VCO)
A VCO generates a periodic signal, whose frequency is a linear function of the input control voltage vcont. In other words a VCO is characterized by, ω = ω 0 + K vco ⋅ v cont . As the
phase is the time integral of the frequency, the output phase of the VCO block is given by,
φ out = ω 0 t + K vco ⋅
t
∫
–∞
(10.12)
v cont dt
where K vco is the gain of the VCO given in rad/s/V, and ω 0 is a fixed frequency offset.
vcont controls a frequency centered around ω 0 . The output signal has the form
t
–∞
x ( t ) = A ⋅ cos ω 0 t + K vco ⋅ ∫
v cont dt
(10.13)
Phase Detectors
The phase detector determines the relative phase difference between two incoming signals
and outputs a signal that is proportional to this phase difference. This output signal is then
used to adjust the output of the VCO and thus align the two inputs via a feedback network.
One of the inputs to the phase detector is a reference clock that is typically generated offchip while the other clock input is a divided version of the VCO. Two basic types of phase
detectors are commonly used. These include the XOR gate and the phase frequency detector (PFD).
XOR Phase Detector. The XOR phase detector is the simplest phase detector. The XOR
is useful as a phase detector since the time when the two inputs are different (or same) represents the relative phase. Figure 10.59 shows the XOR of two waveforms. The output of
chapter10_141.fm Page 90 Tuesday, April 16, 2002 9:12 AM
Section 10.6
Clock Synthesis and Synchronization Using a Phase-Locked Loop
90
the XOR is low pass filtered and acts as a control voltage to the VCO. The output (low
pass filtered) as a function of the phase error is also shown.
ref
ref
Output
local
clock
local
clock
output
Output (Low pass filtered)
VDD
-180
Figure 10.59
-90
90
180
phase error (deg)
The XOR as a phase detector.
For this detector any deviation in a positive or negative direction from the the perfect in-phase condition (i.e., phase error of zero) produces the same change in duty factor
resulting in the same average voltage. Thus the linear phase range is only 180 degrees.
Using such a phase detector, a PLL will lock to a quadrature phase relationship (i.e., 1/4
cycle offset) between the two inputs. A drawback of the XOR phase detector is that it may
lock to a multiple of the clock frequency. If the local clock is a multiple of the reference
clock frequency, the output of the phase detector will still be a square wave of 50% duty
cycle, albeit at a different frequency. The filtered version of this signal will be identical to
that of the truly locked state and thus the VCO will operate at the nominal frequency.
Phase-Frequency Detector. The phase-frequency detector (PFD) is the most commonly
used form of phase detector, and it solves several of the shortcomings of the detectors discussed above. As the name implies, the output of the PFD is dependent both on the phase
and frequency difference of the applied signals. Accordingly, it cannot lock to an incorrect
chapter10_141.fm Page 91 Tuesday, April 16, 2002 9:12 AM
91
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
multiple of the frequency. The PFD takes two clock inputs and produces two outputs, UP
and DOWN as shown in Figure 10.60.
Rst
Q
D
UP
UP=0
DN=1
A
D
A
B
B
UP=0
DN=0
Rst
Q
A
DN
B
(a) schematic
UP = 1
DN = 0
A
B
(b) state transition diagram
A
A
B
B
UP
UP
DN
DN
(c) Timing waveforms
Figure 10.60 Phase-Frequency Detector. (a) Schematic (b) State Transition Diagram (c) Timing.
The PFD is a state machine with 3 states. Assume that both UP and DN outputs are
initially low. When input A leads B, the UP output is asserted on the rising edge of input
A. The UP signal remain in this state until a low-to-high transition occurs on input B. At
that time, the DN output is asserted, causing both flip-flops to reset through the asynchronous reset signal. Notice that a short pulse proportional to the phase error is generated on
the DN signal, and that there is a small pulse on the DN output, whose duration is is equal
to the delay throught he AND gate and register reset delay. The pulse width of the UP
pulse is equal to the phase error between the two signal. The roles are reversed for the case
when input B lags A, and a pulse proportional to the phase error is generated on the DN
output. If the loop is in lock, short pulses will be generated on the UP and DN outputs.
A
B
UP
Figure 10.61 Timing of the PFD measuring
frequency error.
DN
The circuit also acts as a frequency detector, providing a measure of the frequency
error (Figure 10.61). For the case when A is at a higher frequency than B, the PFD generates a lot more UP pulses (with the average proportional to the frequency difference),
chapter10_141.fm Page 92 Tuesday, April 16, 2002 9:12 AM
Section 10.6
Clock Synthesis and Synchronization Using a Phase-Locked Loop
92
while the DN pulses average close to zero. The exactly the opposite is true for the case
when B has a frequency larger than A — many more pulses are generated on the DN output than the UP output.
The phase characterisctics of the phase detector is shown in Figure 10.62. Notice
that the linear range has been expanded to 4π.
Average (UP-DN)
VDD
-2π
2π
phase error (deg)
Figure 10.62 Phase detector characteristic.
VDD
UP
To VCO Control Input
DN
Figure 10.63 Charge Pump.
Charge Pump
The UP/DN pulses must be converted to an analog voltage
that controls the VCO. One possible implementation is
shown in Figure 10.63. A pulse on the UP signal adds a
charge packet proportional to the size of the UP pulse, and
a pulse on the DN signal removes a charge packet proportional to the DN pulse. If the width of the UP pulse is large
than the DN pulse, then there is a net increase in the control
voltage. This effectively increases the frequency of the
VCO.
Simulation
The settling time of a PLL is the time it takes it reach steady state behavior. The period of
the startup transient is strongly dependent on the bandwidth of the loop filter. Figure 10.64
shows a spice level simulation of a PLL (an ideal VCO is used to speed up the simulation)
implemented in 0.25µm CMOS. In this example a reference frequency of 100Mhz is chosen and the PLL multiplies this frequency by 8 to 800Mhz. The figure illustrates the transient response and settling process of the control voltage to the VCO. Once the control
voltage reaches its final value, the output frequency (the clock to the digital system) settles
to its final value. The simulation on the right shows the reference frequency, the output of
the divider and the output frequency. As illustrated in this plot, the top graph show lock in
which fout = 8 * fref. The lower graph shows the waveforms during the locking process
where the output is not in phase with the input and the frequencies are not related through
the divide ratio
.
chapter10_141.fm Page 93 Tuesday, April 16, 2002 9:12 AM
93
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
ref
1.0
div
Control Voltage (V)
0.8
vco
0.6
0.4
ref
0.2
div
0.0
0
1
2
3
Time (µs)
4
5
vco
Figure 10.64 Spice simulation of a PLL. The control voltage of the VCO is shown along with
waveforms before lock and after lock.
Summary
In a short span of time, phased-locked loops have become an essential component of
any high-performance digital design. Their design requires considerable skill, integrating
analog circuitry into a hostile digital environment. Yet, experience has demonstrated that
this combination is perfectly feasible, and leads to new and better solutions.
10.7
Future Directions
This section highlights some of the trends in high-performance and low-power timing
optimization.
10.7.1
Distributed Clocking Using DLLs
A recent trend in high-performance clocking is the use of Delay-Locked Loop (DLL)
structures, a small variation of the PLL structure. A schematic of a DLL is shown in Figure 10.65 [Maneatis00]. The key component of a DLL is a voltage-controlled delay line
(VCDL). It consists of a cascade of adjustable delay elements (for instance, a currentstarved inverter). The idea is to delay the output clock such that it perfectly lines up with
the reference. Unlike a VCO, there is no clock generator. The reference frequency is fed
into the input of the VCDL. Similar to a PLL structure, a phase-detector compares the reference frequency to the output of the delay line (F0), and generates an UP/DN error signal.
Note that only a phase detection is required instead of a PFD. When in lock there is no
chapter10_141.fm Page 94 Tuesday, April 16, 2002 9:12 AM
Section 10.7
Future Directions
94
error between the two clocks. The function of the feedback is to adjust the delay through
the VCDL such that the rising edge of the input reference clock (fREF), and the output
clock fO are aligned .
Figure 10.65 Delay-Locked Loop.
(a)
(b)
(c)
A qualitative sketch of the signals in the DLL is shown in Figure 10.66c. Initially,
the DLL is out of lock. Since the first edge of the output arrives before the reference edge,
an UP pulse of width equal to the error between the two signals. The role of the charge
pump is to generate a charge packet proportional to the error, increasing the voltage of the
VCDL control voltage. This causes the edge of the output signal to be delayed in the next
cycle (this implementation of the VCDL assumes that a large voltage results in larger
delay). After many cycles, the phase error is corrected, and the two signals are in lock.
Figure 10.67 shows the application of a DLL strcuture to clock distribution. The
chip is partitioned into many small regions (or tiles). A global clock is distributed to each
tile in a low-skew manner (e.g., this could be done through the package or using low skew
on-chip routing schemes). For purpose of simplicity, the Figure shows a two-tile chip, but
this is easily extended to many regions. Inside each tile, the global clock is buffered before
driving the digital load. In front of each buffer is a VCDL. The goal of the clock network
is to deliver a signal to the digital circuit with close-to-zero skew and jitter. Unfortunately,
the static and dynamic variations of the buffers cause the phase error between the buffered
clocks to be non-zero and time-varying. This is especially a concern since the delay
through the buffer chain can equal multiple clock cycles. The feedback inside each tile
adjusts the control voltage of VCDL, such that the buffered output is locked in phase to
the global input clock. The feedback loop compensates for both static process variations
and for slow dynamic variations (e.g., temperature). Such configurations have become
common in high performance digital microprocessors.
chapter10_141.fm Page 95 Tuesday, April 16, 2002 9:12 AM
95
TIMING ISSUES IN DIGITAL CIRCUITS
VCDL
Chapter 10
Digital
Circuit
CP/LF
Phase
Detector
GLOBAL CLK
VCDL
Digital
Circuit
CP/LF
Phase
Detector
Figure 10.66 DLL Approach to Clock Distribution.
10.7.2
Optical Clock Distribution
It is clear that there are some fundamental problems associated with electrical synchronization techniques for future high-performance multi-GHz systems. The performance of a
digital is fundametally limited by process and environmental variations. Even with aggressive active clock management schemes such as the use of DLLs and PLLs, the variations
in power supply and clock load result in unacceptable clock uncertainity. As a result, there
has been a major recent push towards the use of optics for system wide synchronization.
An excellent review of the rationale and trade-offs in optical interconnects vs. electrical
interconnect is given in [Miller00].
The potential advantage of optical technology for clock distribution is due to the fact
that the delay is not sensitive to temperature and the clock edges don’t degrade over long
distances (e.g., 10’s meters). In fact, it is possible to deliver an optical clock signal with
10-100ps of uncertanity for 10’s meters. Of course, the performance of an optical system
is limited by the speed of light. Optical clocks can distribution on-chip via waveguides or
freespace. Figure 10.67 shows the plot of an optical clock architecutre using waveguides.
The off-chip optical source is brought to the chip, distributed through waveguides, and
converted through receiver circuitry to a local electrical clock distribution network. The
chip is divided into small sections (or tiles) and each the global clock is distributed from
the photon source (the most popular choice being a laser for its ease of use) through
waveguides with splitters and bends to each of the sections. Notice that an H-treee is used
in distributing the optical clock. At the end of the waveguide is a photodetector (which can
be implemented using silicon or germanium).Once reaching the detector in each section,
the global clock optical pulses are converted into current pulses. These current pulses have
a very small magnitude (10’s µA) and they are fed into a transimpedance amplifier of the
chapter10_141.fm Page 96 Tuesday, April 16, 2002 9:12 AM
Section 10.8
Perspective: Synchronous versus Asynchronous Design
96
optoelectronic circuitry that amplifes the signal into voltage levels appropriate for digital
processing. into voltage signals. The electrical clock is then distributed through conventional techniques to the local load. Optics has the additional advantage that many of the
difficulties with electromagnetic wave phenomena are avoided (e.g., crosstalk or inductive
coupling). A common problem in electrical signals is reflection from the loads, often
requiring termination, hence increasing power dissipation. Optical clocks avoid this probelm and don’t require termination [Miller00].
In such an approach, the skew of the global clock to the photodectors is virtually
zero. There are some variations in the arrival time of the optical signal (e.g., due to variations at bends cause different energy loss along different paths). However, the optical
receiver is typically composed of multiple stages to amplify the small current pulses and is
susseptible to process and environmental variations. The sources of variations are very
similar to a conventional electrical approach including threshold and device variations,
power supply and temperature variations, and variations in the local drivers.
Local Electrical
Distribution
Optical GCLK
Optical
Receiver
waveguides
Figure 10.67
distribution.
Architecture for optical clock
Optical clocking may an important future in high-performance systems. However,
the challenges of dealing with process variations in the opto-electronic circuitry must be
addressed for this to become a reality.
10.8
Perspective: Synchronous versus Asynchronous Design
The self-timed approach offers a potential solution to the growing clock-distribution problem. It translates the global clock signal into a number of local synchronization problems.
Independence from physical timing constraints is achieved with the aid of completion signals. Handshaking logic is needed to ensure the logical ordering of the circuit events and
to avoid race conditions. This requires adherence to a certain protocol, which normally
consists of either two or four phases.
Despite all its advantages, self-timing has only been used in a number of isolated
cases. Examples of self-timed circuits can be found in signal processing [Jacobs90], fast
arithmetic units (such as self-timed dividers) [Williams87], simple microprocessors
[Martin89] and memory (static RAM, FIFOs). In general, synchronous logic is both faster
and simpler since the overhead of completion-signal generation and handshaking logic is
avoided. The design a fool-proof network of handshaking units, that is robust with respect
to races, live-lock, and dead-lock, is nontrivial and requires the availability of dedicated
design-automation tools.
On the other hand, distributing a clock at high speed becomes exceedingly difficult.
This was amply illustrated by the example of the 21164 Alpha microprocessor. Skew man-
chapter10_141.fm Page 97 Tuesday, April 16, 2002 9:12 AM
97
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
agement requires extensive modeling and analysis, as well as careful design. It will not be
easy to extend this methodology into the next generation of designs. This observation is
already reflected in the fact that the routing network for the latest generation of massively
parallel supercomputers is completely implemented using self-timing [Seitz92]. For selftiming to become a mainstream design technique however (if it ever will), further innovations in circuit and signaling techniques and design methodologies are needed. Other alternative timing approaches might emerge as well. Possible candidates are fully asynchronous
designs or islands of synchronous units connected by an asynchronous network.
10.9
Summary
This chapter has explored the timing of sequential digital circuits.
• An in-depth analysis of the synchronous digital circuits and clocking approaches
was presented. Clock skew and jitter has a major impact on the functionality and
performance of a system. Important parameters are the clocking scheme used and
the nature of the clock-generation and distribution network.
• Alternative timing approaches, such as self-timed design, are becoming attractive to
deal with clock distribution problems. Self-timed design uses completion signals
and handshaking logic to isolate physical timing constraints from event ordering.
• The connection of synchronous and asynchronous components introduces the risk of
synchronization failure. The introduction of synchronizers helps to reduce that risk,
but can never eliminate it.
• Phase-locked loops are becoming an important element of the digital-designer’s tool
box. They are used to generate high speed clock signals on a chip. The analog nature
of the PLL makes its design a real challenge.
• Important trends for clock distribution include the use of delay-locked loops to
actively adjust delays on a chip.
• The key message of this chapter is that synchronization and timing are among the
most intriguing challenges facing the digital designer of the next decade.
10.10
To Probe Further
While system timing is an important topic, no congruent reference work is available in this
area. One of the best discussions so far is the chapter by Chuck Seitz in [Mead80, Chapter
7]. Other in-depth overviews are given in [Bakoglu90, Chapter 8], [Johnson93, Chapter
11], [Hatamian88], and [Chandrakasan00]. A collection of papers on clock distribution
networks is presented in [Friedman95]. Numerous other publications are available on this
topic in the leading journals, some of which are mentioned below.
chapter10_141.fm Page 98 Tuesday, April 16, 2002 9:12 AM
Section 10.10
To Probe Further
98
REFERENCES
[Abnous93] A. Abnous and A. Behzad, “A High-Performance Self-Timed CMOS Adder,” in EE241
Final Class Project Reports, by J. Rabaey, Univ. of California—Berkeley, May 1993.
[Bailey00] D. Bailey, “Clock Distribution,” in [Chandrakasan00].
[Bakoglu90] H. Bakoglu, Circuits, Interconnections and Packaging for VLSI, Addison-Wesley,
pp. 338–393, 1980.
[Boning00] D. Boning, S. Nassif, “Models of Process Variations in Device and Interconnect” in
[Chandrakasan00].
[Bowhill95] W. Bowhill et al., “A 300 MHz Quad-Issue CMOS RISC Microprocessor,” Technical
Digest of the 1995 ISSCC Conference, San Fransisco, February 1995.
[Bernstein98] K. Bernstein et. al, High Speed CMOS Design Styles, Kluwer Academic Publishers,
1998.
[Bernstein00] K. Bernstein, “Basic Logic Families”, in [Chandrakasan00].
[Chandrakasan00] A. Chandrakasan, W. Bowhill, and F. Fox, Design of High-Performance Microprocessor Circuits, IEEE Press, 2000.
[Chaney73] T. Chaney and F. Rosenberger, “Anomalous Behavior of Synchronizer and Arbiter Circuits,” IEEE Trans. on Computers, vol. C-22, April 1973, pp. 421–422.
[Dally 98] W. Dally and J. Poulton, Digital Systems Engineering, Cambridge University Press, 1998.
[Dopperpuhl92] D. Dopperpuhl et al., “A 200 MHz 64-b Dual Issue CMOS Microprocessor,” IEEE
Journal on Solid State Circuits, vol. 27, no. 11, Nov. 1992, pp. 1555–1567.
[Friedman95] E. Friedman, ed., Clock Distribution Networks in VLSI Circuits and Systems, IEEE
Press, 1995.
[Gardner80] F. Gardner, “Charge-Pump Phase-Locked Loops,” IEEE Trans. on Communications,
vol. COM-28, November 1980, pp. 1849–1858.
[Glasser85] L. Glasser and D. Dopperpuhl, The Design and Analysis of VLSI Circuits, AddisonWesley, 1985, pp. 360–365.
[Goodman98] J. Goodman, A. P. Dancy, A. P. Chandrakasan, "An Energy/Security Scalable
Encryption Processor Using an Embedded Variable Voltage DC/DC Converter," IEEE Journal of
Solid-state Circuits, pp. 1799-1809, 1998.
[Gray93] P. Gray and R. Meyer, Analysis and Design of Analog Integrated Circuits, 3rd ed., Wiley,
1993.
[Hatamian88] M. Hatamian, “Understanding Clock Skew in Synchronous Systems,” in Concurrent
Computations, ed. S. Tewksbury et al., Plenum Publishing, pp. 86–96, 1988.
[Heller84] L. Heller et al., “Cascade Voltage Switch Logic: A Differential CMOS Logic Family,”
IEEE International Solid State Conference Digest, Feb. 1984, San Francisco, pp. 16–17.
[Jacobs90] G. Jacobs and R. Brodersen, “A Fully Asynchronous Digital Signal Processor,” IEEE
Journal on Solid State Circuits, vol. 25, No 6, December 1990, pp. 1526–1537.
[Jeong87] D. Jeong et al., “Design of PLL-Based Clock Generation Circuits”, IEEE Journal on
Solid State Circuits, vol. SC-22, no 2, April 1987, pp 255–261.
[Johnson93] H. Johnson and M. Graham, High-Speed Digital Design—A Handbook of Black Magic,
Prentice-Hall, N.J, 1993.
[Kim90] B. Kim, D. Helman, and P. Gray, “A 30 MHz Hybrid Analog/Digital Clock Recovery Circuit in 2 µm CMOS,” IEEE Journal on Solid State Circuits, vol. SC-25, no. 6, December 1990,
pp. 1385–1394.
chapter10_141.fm Page 99 Tuesday, April 16, 2002 9:12 AM
99
TIMING ISSUES IN DIGITAL CIRCUITS
Chapter 10
[Martin89] A. Matrin et. al, “The First Asynchronous Microprocessor: Test Results,” Computer
Architecture News, vol. 17 No 4, June 1989, pp. 95–110.
[Mead80] C. Mead and L. Conway, Introduction to VLSI Design, Addison-Wesley, 1980.
[Messerschmitt90] D. Messerschmidtt, “Synchronization in Digital Systems,” IEEE Journal on
Selected Areas in Communications, vol. 8, No. 8, pp. 1404-1419, October 1990.
[Miller2000] D. Miller, “Rationale and Challenges for Optical Interconnects to Electronic Chips,”
Proceedings of the IEEE, pp. 728-749, June 2000.
[Nielsen94] L Nielsen, C. Niessen, J. Sparso, K. van Berkel, “Low-Power Operation Using SelfTimed Circuits and Adaptive Scaling of Supply Voltage,” IEEE Transactions on VLSI systems,
December 1994, pp 391-397.
[Restle98] P. Restle, K. Jenkins, A. Deutsch, P. Cook, “Measurement and Modeling of On-chip
Transmission Line Effects in a 400MHz Microprocessor,” IEEE Journal of Solid-state Circuits,
pp. 662-665, April 1998.
[Seitz80] C. Seitz, “System Timing,” in [Mead80], pp. 218–262, 1980.
[Seitz92] C. Seitz, “Mosaic C: An Experimental Fine-Grain Multicomputer,” in Future Tendencies
in Computer Science, Control and Applied Mathematics, Proceedings International Conference
on the 25th Anniversary of INRIA, Springer-Verlag, Germany, pp. 69–85, 1992.
[Shoji88] M. Shoji, CMOS Digital Circuit Technology, Prentice-Hall, 1988.
[Sutherland89] I. Sutherland, “Micropipelines,” Communications of the ACM, pp. 720–738, June
1989.
[Veendrick80] H. Veendrick, “The Behavior of Flip Flops Used as Synchronizers and Prediction of
Their Failure Rates”, IEEE Journal of Solid State Circuits, vol. SC-15, no 2, April 1980, pp.
169–176.
[Williams87] T. Williams et al., “A Self-Timed Chip for Division,” in Proc. of Advanced Research
in VLSI 1987, Stanford Conf., pp. 75–96, March 1987.
EXERCISES AND DESIGN PROBLEM
Please refer to the book web-page (http://bwrc.eecs.berkeley.edu/IcBook) for
insightful and challenging exercises and design problems.
DMIA.fm Page 71 Friday, January 18, 2002 9:09 AM
DESIGN METHODOLOGY INSERT
A
IC LAYOUT
Creating a manufacturable layout
n
Verifying the layout
The increasing complexity of the integrated circuit has made the role of design-automation tools indispensable, and raises the abstractions the designer is working with to ever
higher levels. Yet, when performance or design density is of primary importance, the
designer has no other choice than to return to handcrafting the circuit topology and physical design. The labor-intensive nature of this approach, called custom design, translates
into a high cost and a long time-to-market. Therefore, it can only be justified economically
under the following conditions:
• The custom block can be reused many times, for instance as a library cell
• The cost can be amortized over a large volume. Microprocessors and semiconductor
memories are examples of applications in this class.
• Cost is not the prime design criterion. This is becoming increasingly rare. Examples
are space-applications and scientific instrumentation.
With continuous progress in the design-automation arena, the share of custom design
reduces from year to year. Even in high-performance microprocessors, large portions are
designed automatically using semicustom design approaches. Only the most performancecritical modules such as the integer and floating-point execution units are handcrafted.
71
DMIA.fm Page 72 Friday, January 18, 2002 9:09 AM
IC LAYOUT
72
Chapter A
Even though the amount of design automation in the custom design process is minimal, some design tools have proven to be indispensable. Together with circuit simulators,
these programs form the core of every design-automation environment, and are the first
tools an aspirant circuit designer will encounter.
Layout Editor
The layout editor is the premier working tool of the designer and exists primarily for the
generation of a physical representation of a design, given a circuit topology. Virtually
every design-automation vendor offers an entry in this field. Most well-known is the
MAGIC tool developed at the University of California at Berkeley [Ousterhout84], which
has been widely distributed. Even though MAGIC did not withstand the evolution of software technology and user interface, some of its offspring did. Throughout this textbook,
we will be using a layout tool called max, a MAGIC descendant developed by a company
called MicroMagic [mmi00]. A typical max display is shown in Figure A.1 and illustrates
the basic function of the layout editor—placing polygons on different mask layers so that
a functional physical design is obtained (scathingly called polygon pushing).
Figure A.1 View of a max
display window. It plots the layout
of two stacked NMOS transistor.
The menu on the left side allows
for the selection of the layer a
particular polygon will be placed
on.
Since physical design occupies a major fraction of the design time for a new cell or
component, techniques to expedite this process have been in continual demand. The symbolic-layout approach has gained popularity over the years. In this design methodology,
the designer only draws a shorthand notation for the layout structure. This notation indicates only the relative positioning of the various design components (transistors, contacts,
DMIA.fm Page 73 Friday, January 18, 2002 9:09 AM
Section
73
wires). The absolute coordinates of these elements are determined automatically by the
editor using a compactor [Hsueh79, Weste93]. The compactor translates the design rules
into a set of constraints on the component positions, and solves a constrained optimization
problem that attempts to minimize the area or another cost function.
An example of a symbolic notation for a circuit topology, called a sticks diagram, is
shown in Figure A.2. The different layout entities are dimensionless, since only positionVDD
3
Out
In
1
Figure A.2 Sticks representation of CMOS inverter. The
numbers represent the (Width /Length)-ratios of the transistors.
GND
In
ing is important. The advantage of this approach is that the designer does not have to
worry about design rules, because the compactor ensures that the final layout is physically
correct. Thus, she can avoid cumbersome polygon manipulations. Another plus of the
symbolic approach is that cells can adjust themselves automatically to the environment.
For example, automatic pitch-matching of cells is an attractive feature in module generators. Consider the case of Figure A.3 (from [Croes88]), in which the original cells have
BEFORE
AFTER
Figure A.3
Automatic pitch matching of data path cells based on symbolic layout.
different heights, and the terminal positions do not match. Connecting the cells would
require extra wiring. The symbolic approach allows the cells to adjust themselves and connect without any overhead.
The disadvantage of the symbolic approach is that the outcome of the compaction
phase is often unpredictable. The resulting layout can be less dense than what is obtained
with the manual approach. Notwithstanding, symbolic layout tools have improved considerably over the years and are currently a part of the mainstream design process.
DMIA.fm Page 74 Friday, January 18, 2002 9:09 AM
IC LAYOUT
74
Chapter A
Design-Rule Checking
Design rules were introduced in Chapter 2 as a set of layout restrictions that ensure the
manufactured design will operate as desired with no short or open circuits. A prime
requirement of the physical layout of a design is that it adhere to these rules. This can be
verified with the aid of a design-rule checker (DRC), which uses as inputs the physical
layout of a design and a description of the design rules presented in the form of a technology file. Since a complex circuit can contain millions of polygons that must be checked
against each other, efficiency is the most important property of a good DRC tool. The verification of a large chip can take hours or days of computation time. One way of expediting the process is to preserve the design hierarchy at the physical level. For instance, if a
cell is used multiple times in a design, it should be checked only once. Besides speeding
up the process, the use of hierarchy can make error messages more informative by retaining knowledge of the circuit structure.
DRC tools come in two formats: (1) The on-line DRC runs concurrent with the layout editor and flags design violations during the cell layout. For instance, max has a builtin design-rule checking facility. An example of on-line DRC is shown in Figure A.4. (2)
Batch DRC is used as a post-design verifier, and is run on a complete chip prior to shipping the mask descriptions to the manufacturer.
Figure A.4 On-line design rule checking. The white
dots indicate a design rule violation. The violated rule
can be obtained with a simple mouse click.
poly_not_fet to all_diff minimum spacing = 0.14 um.
Circuit Extraction
Another important tool in the custom-design methodology is the circuit extractor, which
derives a circuit schematic from a physical layout. By scanning the various layers and
their interactions, the extractor reconstructs the transistor network, including the sizes of
the devices and the interconnections. The schematic produced can be used to verify that
the artwork implements the intended function. Furthermore, the resulting circuit diagram
contains precise information on the parasitics, such as the diffusion and wiring capacitances and resistances. This allows for a more accurate simulation and analysis. The complexity of the extraction depends greatly upon the desired information. Most extractors
extract the transistor network and the capacitances of the interconnect with respect to
GND or other network nodes. Extraction of the wiring resistances already comes at a
DMIA.fm Page 75 Friday, January 18, 2002 9:09 AM
Section
75
greater cost, yet has become a necessity for virtually all high-performance circuits. Clever
algorithms have helped to reduce the complexity of the resulting circuit diagrams. For
very high speed circuits, extraction of the inductance would be desirable as well. Unfortunately, this requires a three-dimensional analysis and is only feasible for small-sized circuits at present.
To Probe Further
More detailed information regarding the MAGIC and max layout editors can be found on
the web-site of this book. In-depth textbooks on layout generation and verification have
been published, and can be of great help to the novice designer. Just to mention a number
of them, [Clein00], [Uyemura95], [Wolf94], and [Weste93] offer some comprehensive
and well-illustrated treatment and discussion.
REFERENCES
[Clein00] D. Clein, CMOS IC Layout—Concepts, Methodologies, and Tools, Newnes, 2000.
[Croes88] K. Croes, H. De Man, and P. Six, “CAMELEON: A Process-Tolerant Symbolic Layout
System,” Journal of Solid State Circuits, vol. 23 no. 3, pp. 705–713, June 1988.
[Hsueh79] M. Hsueh and D. Pederson, “Computer-Aided Layout of LSI Building Blocks,” Proceedings ISCAS Conf., pp. 474–477, Tokyo, 1979.
[mmi00] MicroMagic, Inc, http://www.micromagic.com.
[Ousterhout84] J. Ousterhout, G. Hamachi, R. Mayo, W. Scott, and G. Taylor, “Magic: A VLSI Layout System,” Proc. 21st Design Automation Conference, pp. 152–159, 1984.
[Uyemura95] J. Uyemura, Physical Design of CMOS Integrated Circuits Using L-EDIT, PWS Publishing Company, 1995.
[Weste93] N. Weste and K. Eshraghian, Principles of CMOS VLSI Design—A Systems Perspective,
Addison-Wesley, 1993.
[Wolf94] W. Wolf, Modern VLSI Design—A Systems Approach, Prentice Hall, 1994.
DMIA.fm Page 76 Friday, January 18, 2002 9:09 AM
76
IC LAYOUT
Chapter A
dmie.fm Page 358 Tuesday, April 2, 2002 9:04 AM
DESIGN METHODOLOGY INSERT
E
CHARACTERIZING LOGIC AND
SEQUENTIAL CELLS
The challenge of library characterization
n
Characterization methods for logic cells and registers
n
Cell parameters
The Importance and Challenge of Library Characterization
The quality of the results produced by a logic synthesis tool is a strong function of the
level of detail and accuracy with which the individual cells were characterized. To estimate the delay of a complex module, a logic synthesis program must rely on higher-level
delay models of the individual cells—falling back to a full circuit- or switch level timing
model for each delay estimation is simply not possible from a perspective of compute
time. Hence, an important component in the development process of a standard-cell
library is the generation of the delay models. In previous chapters, we learned that the
delay of a complex gate is a function of the fanout (consisting of connected gates and
wires), and the rise-and fall times of the input signals. Furthermore, the delay of a call can
vary between manufacturing runs as a result of process variations.
In this insert, we discuss first the models and characterization methods that are commonly used for logic cells. Sequential registers require some extra timing parameters, and
deserve a separate discussion.
358
dmie.fm Page 359 Tuesday, April 2, 2002 9:04 AM
CHARACTERIZING LOGIC AND SEQUENTIAL CELLS
359
Insert E
Characterization of Logic Cells
Unfortunately, no common delay model for standard cells has been adopted. Every vendor
has his own favored methods of cell characterization. Even within a single tool, various
delay models can often be used, trading off acuracy for performance. The basic concepts
are however quite similar, and are closely related to the ones we introduced in Chapters 5
and 6. We therefore opt to concentrate on a single set of models in this section; more pre
cisley, those used in the Synopsys Design Compiler [DesignCompiler01], one of the most
popular synthesis tools. Once a model has been adopted, it has to be adopted for all the
cells in the block; in other words, it can’t be changed from cell to cell.
The total delay consists of four components, as illustrated in Figure E.1:
Dtotal = DI + DT + DS + DC.
(E.1)
DI represents the intrinsic delay, this is the delay with no output loading. DT is the ‘transition’ component, or the part of the delay caused by the output load. DS is the fraction of
the delay due to the input slope. Finally, DC is the delay of the wire following the gate. All
delays are characterized for both rising and falling transitions.
Figure E.1 Delay components.
The simplest model for the transition delay is the linear delay model of Chapter 5,
DT = Rdriver(ΣCgate + Cwire),
(5.2)
where ΣCgate is the sum of all input pin capacitances of gates connected to the output of
this gate, and Cwire is the estimated wire capacitance. Similarly, the slope delay DS can be
approximated as a linear function of the transition delay DT of the previous gate,
DS = SS DTprev
(5.3)
with SS is the slope-sensitivity factor, and DTprev the transition delay of the previous stage.
The characterization of a library cell therefore must provide the following components, each of them for both rising and falling transitions, and with respect to each of the
input pins:
• intrinsic delay;
• input pin capacitance;
• equivalent output driving resistance;
dmie.fm Page 360 Tuesday, April 2, 2002 9:04 AM
CHARACTERIZING LOGIC AND SEQUENTIAL CELLS
Insert E
360
• and slope sensitivity.
In addition to the cell models, the synthesis tools also must have access to a wire
model. Since the length of the wires is unknown before the placement of the cells, estimates of Cwire and Rwire are made based on the size of the block, and the fanout of the gate.
The length of a wire is most often proportional the number of destinations it has to connect.
Example E.1 3-Input NAND Gate Cell
To characterization of the 3-input NAND standard cell gate, presented earlier in Example 8.1,
is given in Table E.1. The table characterizes the performance of the cell as a function of the
load capacitance and the input-rise(fall) time for two different supply voltages and operating
temperatures. The cell is designed in a 0.18 µm CMOS technology.
Table E.1 Delay characterization of 3-input NAND gate (in nsec) as a function of the input
node for two operation corners (supply voltage-temperature of 1.2V - 125°C, and 1.6V - 40°C)
. The parameters are the load capacitance C and the input rise(fall) time T.
Path
1.2V - 125°C
1.6V - 40°C
In1—tpLH
0.073+7.98C+0.317T
0.020+2.73C+0.253T
In1—tpHL
0.069+8.43C+0.364T
0.018+2.14C+0.292T
In2—tpLH
0.101+7.97C+0.318T
0.026+2.38C+0.255T
In2—tpHL
0.097+8.42C+0.325T
0.023+2.14C+0.269T
In3—tpLH
0.120+8.00C+0.318T
0.031+2.37C+0.258T
In3—tpHL
0.110+8.41C+0.280T
0.027+2.15C+0.223T
While linear delay models offer good first-order estimates, more precise models are
often used in synthesis, especially when the real wire lengths are back-annotated onto the
design. Under those circumstances, non-linear models have to be adopted. The most common approach is to capture the non-linear relations as lookup tables for each of these
parameters. To increase computational efficiency and minimize storage and characterization requirements, only a limited set of loads and slopes are captured, and linear interpolation is used to determine the values in-between.
Example E.2 Delay models using lookup-tables
A (partial) characterization of a 2-input AND cell (AND2), designed in a 0.25 µm CMOS
technology [STMicro01], is given below. The delays are captured for output capacitances of
7fF, 35fF, 70fF and 140fF, and input slopes of 40ps, 200ps, 800ps and 1.6ns, respectively.
cell(AND) {
area : 36 ;
pin(Z) {
direction : output ;
function : "A*B";
max_capacitance : 0.14000 ;
dmie.fm Page 361 Tuesday, April 2, 2002 9:04 AM
CHARACTERIZING LOGIC AND SEQUENTIAL CELLS
361
Insert E
timing() {
related_pin : "A" ; /* delay between input pin A and output pin Z */
cell_rise {
values( "0.10810, 0.17304, 0.24763, 0.39554", \
"0.14881, 0.21326, 0.28778, 0.43607", \
"0.25149, 0.31643, 0.39060, 0.53805", \
"0.35255, 0.42044, 0.49596, 0.64469" ); }
rise_transition {
values( "0.08068, 0.23844, 0.43925, 0.84497", \
"0.08447, 0.24008, 0.43926, 0.84814", \
"0.10291, 0.25230, 0.44753, 0.85182", \
"0.12614, 0.27258, 0.46551, 0.86338" );}
cell_fall(table_1) {
values( "0.11655, 0.18476, 0.26212, 0.41496", \
"0.15270, 0.22015, 0.29735, 0.45039", \
"0.25893, 0.32845, 0.40535, 0.55701", \
"0.36788, 0.44198, 0.52075, 0.67283" );}
fall_transition(table_1) {
values( "0.06850, 0.18148, 0.32692, 0.62442", \
"0.07183, 0.18247, 0.32693, 0.62443", \
"0.09608, 0.19935, 0.33744, 0.62677", \
"0.12424, 0.22408, 0.35705, 0.63818" );}
intrinsic_rise : 0.13305 ; /* unloaded delays */
intrinsic_fall : 0.13536 ;
}
timing() {
related_pin : "B" ; /* delay between input pin A and output pin Z */
...
intrinsic_rise : 0.12426 ;
intrinsic_fall : 0.14802 ;
}
}
pin(A) {
direction : input ;
capacitance : 0.00485 ; /* gate capacitance */
}
pin(B) {
direction : input ;
capacitance : 0.00519 ;
}
}
Characterization of Registers
In Chapter 7, we identified the three important timing parameters of a register. The set-up
time (tsu) is the time that the data inputs (D input) must be valid before the clock transition
(this is, the 0 to 1 transition for a positive edge-triggered register). The hold time (thold) is
the time the data input must remain valid after the clock edge. Finally, the propagation
delay (tc-q) equals the time it takes for the data to be copied to the Q output after a clock
event. The latter parameter is illustrated in Figure E.2a.
Latches are a bit more complex, and require an extra timing parameter. While tC-Q,
corresponds to the delay of re-launching of data that arrived to a closed latch, tD-Q equals
the delay between D and Q terminals when the latch is in transparent mode (Figure E.2b).
dmie.fm Page 362 Tuesday, April 2, 2002 9:04 AM
CHARACTERIZING LOGIC AND SEQUENTIAL CELLS
Insert E
362
tD-Q
Q
D
Clk
tC-Q
Q
D
Figure E.2 Propagation delay definitions for
sequential components:
(a) register;
(b) latch.
Clk
tC-Q
(a)
(b)
The characterization of the tC-Q (tD-Q) delay is fairly straightforward. It consists of a
delay measurement between the 50% transitions of Clk (D) and Q, for different values of
the input slopes and the output loads.
The characterization of setup and hold times is more elaborate, and depends upon
what is defined as “valid” in the definitions of both setup and hold times. Consider the
case of the set-up time. Narrowing the time interval between the arrival of the data at the D
input and the Clk event does not lead into instantaneous failure, but rather in a gradual
degradation in the delay of the register. This is documented in Figure E.3a, which illustrates the behavior of a register when the data arrives close to the setup time. If D changes
long before the clock edge, the tC-Q delay has a constant value. Moving the data transition
closer to the clock edge causes tC-Q to increase. Finally, if the data changes too close to
the clock edge, the register fails to register the transition altogether.
Clk
t
D
t
Q
t
1.05tC-Q
tC-Q
tSu
tD-C
tH
Figure E.3 Characterization of sequential elemnts: (a) determining the setup time of a register; (b)
definition of setup and hold times.
Clearly, a more precise definition of the “setup time” concept is necessary. A unambiguous specification can be obtained by plotting the tC-Q delay against the data-to-clock
offset, as shown in Figure E.3b. The degradation of the delay for smaller values of the off-
dmie.fm Page 363 Tuesday, April 2, 2002 9:04 AM
CHARACTERIZING LOGIC AND SEQUENTIAL CELLS
363
Insert E
set can be observed. The actual definition of the setup time is rather precarious. If it were
defined as the minimum D-Clk offset that causes the flip-flop to fail, the logic following
the register would suffer from excessive delay if the offset is close to, but larger than, that
point of failure. Another option is to place it at the operation point of the register that minimizes the sum of the data-clock offset and the tC-Q delay. This point, which minimizes the
overall flip-flop overhead, is reached when the slope of the delay curve in Figure E.3b
equals 45 degrees.
While custom design can take advantage of driving flip-flops that close to their
point of failure—and take all the risk that comes with it—, semi-custom design must take
a more conservative approach. For the characterization of registers in a standard cell
library, both setup and hold times are commonly defined as data-clock offsets that correspond to some fixed percentage increase in tC-Q, typically set at 5%, as indicated in Figure E.3b. Note that these curves are different for 0-1 and 1-0 transitions, resulting in
different setup (an hold) times for 0 and 1 values. Identical definitions hold for latches.
Example E.3 Register setup and hold times
REFERENCES
[STMicro01]
Chapter 3 Problem Set
1
Chapter 3
PROBLEMS
For all problems, use the device parameters provided in Chapter 3 (Tables 3.2 and 3.5) and the inside
back book cover, unless otherwise mentioned. Also assume T = 300 K by default.
1. [E,SPICE,3.2.2]
a. Consider the circuit of Figure 0.1. Using the simple model, with VDon = 0.7 V, solve for ID.
b. Find ID and VD using the ideal diode equation. Use Is = 10–14 A and T = 300 K.
c. Solve for VD1, VD2, and ID using SPICE.
d. Repeat parts b and c using IS = 10–16 A, T = 300K, and IS = 10–14A, T = 350 K.
R1 = 2kΩ
+
2.5 V
–
R2 = 2kΩ
ID
+
VD
–
Figure 0.1
2.
Resistor diode circuit.
[M, None, 3.2.3] For the circuit in Figure 0.2, Vs = 3.3 V. Assume AD = 12 µm2, φ0 = 0.65 V,
and m = 0.5. NA = 2.5 E16 and ND = 5 E15.
a. Find ID and VD.
b. Is the diode forward- or reverse-biased?
c. Find the depletion region width, Wj, of the diode.
d. Use the parallel-plate model to find the junction capacitance, Cj.
e. Set Vs = 1.5 V. Again using the parallel-plate model, explain qualitatively why Cj
increases.
Rs = 2 kΩ
+
Vs=3.3V
–
3.
4.
ID
–
VD
+
Figure 0.2
Series diode circuit
[E, None, 3.3.2] Figure 0.3 shows NMOS and PMOS devices with drains, source, and gate
ports annotated. Determine the mode of operation (saturation, linear, or cutoff) and drain current ID for each of the biasing configurations given below. Verify with SPICE. Use the following transistor data: NMOS: k'n = 115µA/V2, VT0 = 0.43 V, λ = 0.06 V–1, PMOS: k'p = 30
µA/V2, VT0 = –0.4 V, λ = -0.1 V–1. Assume (W/L) = 1.
a. NMOS: VGS = 2.5 V, VDS = 2.5 V. PMOS: VGS = –0.5 V, VDS = –1.25 V.
b. NMOS: VGS = 3.3 V, VDS = 2.2 V. PMOS: VGS = –2.5 V, VDS = –1.8 V.
c. NMOS: VGS = 0.6 V, VDS = 0.1 V. PMOS: VGS = –2.5 V, VDS = –0.7 V.
[E, SPICE, 3.3.2] Using SPICE plot the I-V characteristics for the following devices.
Chapter 3 Problem Set
2
D
G
S
5.
6.
G
ID
D
Figure 0.3 NMOS and PMOS devices.
a. NMOS W = 1.2µm, L = 0.25µm
b. NMOS W = 4.8µm, L = 0.5µm
c. PMOS W = 1.2 µm, L = 0.25 µm
d. PMOS W = 4.8 µm, L = 0.5 µm
[E, SPICE, 3.3.2] Indicate on the plots from problem 4.
a. the regions of operation.
b. the effects of channel length modulation.
c. Which of the devices are in velocity saturation? Explain how this can be observed on the IV plots.
[M, None, 3.3.2] Given the data in Table 0.1 for a short channel NMOS transistor with
VDSAT = 0.6 V and k′ =100 µA/V2, calculate VT0, γ, λ, 2|φf|, and W / L:
Table 0.1
7.
S
ID
Measured NMOS transistor data
VGS
VDS
VBS
ID (µA)
1
2.5
1.8
0
1812
2
2
1.8
0
1297
3
2
2.5
0
1361
4
2
1.8
–1
1146
5
2
1.8
-2
1039
[E, None, 3.3.2] Given Table 0.2 ,the goal is to derive the important device parameters from
these data points. As the measured transistor is processed in a deep-submciron technology, the
‘unified model’ holds. From the material constants, we also could determine that the saturation voltage VDSAT equals -1V. You may also assume that -2ΦF = -0.6V.
NOTE: The parameter values on Table 3.3 do NOT hold for this problem.
a. Is the measured transistor a PMOS or an NMOS device? Explain your answer.
b. Determine the value of VT0.
c. Determine γ.
d. Determine λ.
Digital Integrated Circuits - 2nd Ed
3
e. Given the obtained answers, determine for each of the measurements the operation region
of the transistor (choose from cutoff, resistive, saturated, and velocity saturated). Annotate
your finding in the right-most column of the above.
Table 0.2 Measurements taken from the MOS device, at different terminal voltages.
8.
Measurement
number
VGS
(V)
VDS
(V)
VSB
(V)
ID (µA)
1
-2.5
-2.5
0
-84.375
2
1
1
0
0.0
3
-0.7
-0.8
0
-1.04
4
-2.0
-2.5
0
-56.25
5
-2.5
-2.5
-1
-72.0
6
-2.5
-1.5
0
-80.625
7
-2.5
-0.8
0
-66.56
Operation
Region?
[M, None, 3.3.2] An NMOS device is plugged into the test configuration shown below in Figure 0.4. The input Vin =2V. The current source draws a constant current of 50 µA. R is a variable resistor that can assume values between 10kΩ and 30 kΩ. Transistor M1 experiences
short channel effects and has following transistor parameters: k’ = 110*10-6 V/A2, VT = 0.4 ,
and VDSAT = 0.6V. The transistor has a W/L = 2.5µ/0.25µ. For simplicity body effect and
channel length modulation can be neglected. i.e λ=0, γ=0. .
VDD = 2.5V
R
VD
Vin=2V
M1
W/L = 2.5µ/0.25µ
VS
I = 50µΑ
9.
Figure 0.4
Test configuration for the NMOS device.
a. When R =10kΩ find the operation region, VD and VS.
b. When R= 30kΩ again determine the operation region VD, VS
c. For the case of R = 10kΩ, would VS increase or decrease if λ ≠
[M, None, 3.3.2] Consider the circuit configuration of Figure 0.5.
0. Explain qualitatively
Chapter 3 Problem Set
4
a. Write down the equations (and only those) which are needed to determine the voltage at
node X. Do NOT plug in any values yet. Neglect short channel effects and assume that λp
= 0.
b. Draw the (approximative) load lines for both MOS transistor and resistor. Mark some of
the significant points.
c. Determine the required width of the transistor (for L = 0.25µm) such that X equals 1.5 V.
d. We have, so far, assumed that M1 is a long-channel device. Redraw the load lines assuming that M1 is velocity-saturated. Will the voltage at X rise or fall?
2.5 V
R1 = 20 kΩ
I
X
M1
Figure 0.5
10.
MOS circuit.
[M, None, 3.3.2] The circuit of Figure 0.6 is known as a source-follower configuration. It
achieves a DC level shift between the input and output. The value of this shift is determined
by the current I0. Assume γ = 0.4, 2|φf| = 0.6 V, VT0 = 0.43 V, k′ = 115 µA/V2, and λ = 0. The
NMOS device has W/L = 5.4µ/1.2µ such that the short channel effects are not observed.
a. Derive an expression giving Vi as a function of Vo and VT(Vo). If we neglect body effect,
what is the nominal value of the level shift performed by this circuit.
b. The NMOS transistor experiences a shift in VT due to the body effect. Find VT as a function
of Vo for Vo ranging from 0 to 1.5V with 0.25 V intervals. Plot VT vs. Vo.
c. Plot Vo vs. Vi as Vo varies from 0 to 1.5 V with 0.25 V intervals. Plot two curves: one
neglecting the body effect and one accounting for it. How does the body effect influence
the operation of the level converter? At Vo (body effect) = 1.5 V, find Vo (ideal) and, thus,
determine the maximum error introduced by body effect.
VDD = 2.5 V
Vi
5.4µ/1.2µ
Vo
I0 = 35 µA
Figure 0.6
11.
Source-follower level converter.
[M, SPICE, 3.3.2] Problem 11 uses the MOS circuit of Figure 0.7.
a. Plot Vout vs. Vin with Vin varying from 0 to 2.5 volts (use steps of 0.5V). VDD = 2.5 V.
b. Repeat a using SPICE.
c. Repeat a and b using a MOS transistor with (W / L) = 4 / 1. Is the discrepancy between
manual and computer analysis larger or smaller. Explain why.
Digital Integrated Circuits - 2nd Ed
5
VDD=2.5V
8 kΩ
Vout
Vin
M1
1µ/0.25µ
Figure 0.7
12.
MOS circuit.
[E, None, 3.3.2]Below in Figure 0.8 is an I-V transfer curve for an NMOS transistor. In this
problem, the objective is to use this I-V curve to obtain information about the transistor. The
transistor has (W/L)=(1µ/1µ). It may also be assumed that velocity saturation does not play a
role in this example. Also assume -2ΦF = 0.6V. Using Figure 0.8 determine the following
parameters: device VTO, γ, λ.
Figure 0.8
I-V curves
Chapter 3 Problem Set
6
13.
[E, None , 3.3.2]The curves below in Figure 0.9 represent the gate voltage(VGS) vs. drain current (IDS) of two NMOS devices which are on the same die and operate in subthreshold
region. Due to process variations on the same die the curves do not overlap.
10
10
10
10
-4
-5
-6
Figure 0.9 Subthreshold
current curves. Difference is
due to process variations
-7
I
DS
10
IDS vs V GS in weak inversion
-3
10
10
10
10
-8
-9
-10
-11
0
0.1
0.2
0.3
0.4
0.5
V GS
0.6
0.7
0.8
0.9
1
Also assume that the transistors are within the same circuit configurations as Figure 0.10
in If the in put voltages are both Vin = 0.2V. What would be the respective durations to discharge the load of CL = 1pF attached to the drains of these devices.
Vd
CL = 1pF
Vin
14.
M1
Figure 0.10 The circuit for testing the time to
discharge the load capacitance through a device
operating in subthreshold region.
[M, None, 3.3.2] Short-channel effects:
a. Use the fact that current can be expressed as the product of the carrier charge per unit
length and the velocity of carriers (IDS = Qv) to derive IDS as a function of W, Cox, VGS – VT,
and carrier velocity v.
b. For a long-channel device, the carrier velocity is the mobility times the applied electric
field. The electrical field, which has dimensions of V/m, is simply (VGS – VT ) / 2L. Derive
IDS for a long-channel device.
c. From the equation derived in a, find IDS for a short-channel device in terms of the maximum carrier velocity, vmax.
Based on the results of b and c describe the most important differences between shortchannel and long-channel devices.
Digital Integrated Circuits - 2nd Ed
15.
7
[C, None, 3.3.2] Another equation, which models the velocity-saturated drain current of an
MOS transistor is given by
µ 0 C ox W
1
I dsat = -------------------------------------------------------- -------------- ----- ( V GS – V T ) 2
1 + ( V GS – V t ) ⁄ ( E sat L ) 2 L
Using this equation it is possible to see that velocity saturation can be modeled by a MOS
device with a source-degeneration resistor (see Figure 0.11).
a. Find the value of RS such that IDSAT(VGS, VDS) for the composite transistor in the figure
matches the above velocity-saturated drain current equation. Hint: the voltage drop across
RS is typically small.
b. Given Esat = 1.5 V/µm and k′ = µ0Cox = 20 µA/V2, what value of RS is required to model
velocity saturation. How does this value depend on W and L?
VD
W/L
VG
V′S
RS
VS
16.
Figure 0.11 Source-degeneration model of
velocity saturation.
[E, None, 3.3.2] The equivalent resistances of two different devices need to be computed.
a. First, consider the fictive device whose I-V characteristic is given in Figure 0.12. Constant
k has the dimension of S (or1/Ω). V0 is a voltage characteristic to the device. Calculate the
equivalent resistance for an output voltage transition from 0 to 2V0 by integrating the
resistance as a function of the voltage.
I(A)
I = k*V*e(V/V0)
I
+
V
Figure 0.12 Fictive device
whose equivalent resistance is to
be calculated.
V(V)
-
b. Next, obtain the resistance equation 3.43 using the Figure 0.13. Assuming the VGS is kept
at VDD, Calculate the Req as output (VDS) transitions from VDD to VDD/2.(Figure 0.13).
Chapter 3 Problem Set
8
Hint: Make sure you use the Short channel Unified MOS Model equations. Hint: You
will need to use the expansion. ln(1+x) ≈ x - x2/2 + x3/3
VDD →VDD/2
VDD
17.
18.
Figure 0.13 The equivalent resistance is to
be computed for the H→L transition.
[M, None, 3.3.3] Compute the gate and diffusion capacitances for transistor M1 of Figure 0.7.
Assume that drain and source areas are rectangular, and are 1 µm wide and 0.5 µm long. Use
the parameters of Example 3.5 to determine the capacitance values. Assume mj = 0.5 and
mjsw = 0.44. Also compute the total charge stored at node In, for the following initial conditions:
a. Vin = 2.5 V, Vout = 2.5 V, 0.5 V, and 0 V.
b. Vin = 0 V, Vout = 2.5 V, 0.5 V, and 0 V.
[E, None, 3.3.3]Consider a CMOS process with the following capacitive parameters for the
NMOS transistor: CGSO, CGDO, COX, CJ, mj, Cjsw, mjsw, and PB, with the lateral diffusion equal
to LD. The MOS transistor M1 is characterized by the following parameters: W, L, AD, PD,
AS, PS.
VDD=VT
Vg
M1
Iin
Figure 0.14
capacitance
Circuit to measure total input
CT
a. Consider the configuration of Figure 0.14. VDD is equal to VT (the threshold voltage of the
transistor) Assume that the initial value of Vg equals 0. A current source with value Iin is
applied at time 0. Assuming that all the capacitance at the gate node can be lumped into a
single, grounded, linear capacitance CT, derive an expression for the time it will take for
Vg to reach 2 VT
b. The obvious question is now how to compute CT. Among, Cdb, Csb, Cgs, Cgd, Cgb which of
these parasatic capacitances of the MOS transistor contribute to CT. For those that contribute to CT write down the expression that determines the value of the contribution. Use only
the parameters given above. If the transistor goes through different operation regions and
this impacts the value of the capacitor, determine the expression of the contribution for
each region (and indicate the region).
Digital Integrated Circuits - 2nd Ed
9
c. Consider now the case depicted in Figure 0.15. Asssume that Vd is initially at 0 and we
want to charge it up to 2 VT. Again among, Cdb, Csb, Cgs, Cgd, Cgb which device capacitances contribute to the total drain capacitance? Once again, make sure you differentiate
between different operation regions..
Vd
CT
Iin
M1
Figure 0.15
capacitance
19.
Circuit to measure the total drain
[M, None, 3.3.3]For the NMOS transistor in Figure 0.16, sketch the voltages at the source
and at the drain as a function of time. Initially, both source and drain are at +2.5 volts. Note
that the drain is open circuited. The 10 µA current source is turned on at t=0. Device parameters:W/Leff = 125µ/0.25µ ; µCox = 100 µA/V2 ; Cox = 6fF/µ2 ;COL(per width) = 0.3 fF/µ ; Csb =
100 fF; Cdb = 100fF;VDSAT =1V.
HINT:Do not try to solve this analytically. Just use a qualitative analysis to derive the different operation modes of the circuit and the devices.
Cgd
d
Cdb
g
s
2.5V
Csb
Cgs
10µA
Figure 0.16 Device going through different
operation regions over time
20.
21.
[C, SPICE, 3.4] Though impossible to quantify exactly by hand, it is a good idea to understand
process variations and be able to at least get a rough estimate for the limits of their effects.
a. For the circuit of Figure 0.7, calculate nominal, minimum, and maximum currents in the
NMOS device with Vin = 0 V, 2.5 V and 5 V. Assume 3σ variations in VT0 of 25 mV, in k′ of
15%, and in lithographic etching of 0.15 µm.
b. Analyze the impact of these current variations on the output voltage. Assume that the load
resistor also can vary by 10%. Verify the result with SPICE.
[E, None, 3.5] A state-of-the-art, synthesizable, embedded microprocessor consumes
0.4mW/MHz when fabricated using a 0.18 µm process. With typical standard cells (gates),
the area of the processor is 0.7 mm2. Assuming a 100 Mhz clock frequency, and 1.8 V power
Chapter 3 Problem Set
10
22.
supply. Assume short channel devices, but ignore second order effects like mobility degradation, series resistance, etc.
a. Using fixed voltage scaling and constant frequency, what will the area, power consumption, and power density of the same processor be, if scaled to 0.12 µm technology, assuming the same clock frequency?
b. If the supply voltage in the scaled 0.12 µm part is reduced to 1.5 V what will the power
consumption and power density be?
c. How fast could the scaled processor in Part (b) be clocked? What would the power and
power density be at this new clock frequency?
d. Power density is important for cooling the chip and packaging. What would the supply
voltage have to be to maintain the same power density as the original processor?
The superscalar, superpipelined, out-of-order executing, highly parallel, fully x86 compatible
JMRII microprocessor was fabricated in a 0.25 m technology and was able to operate at 100
MHZ, consuming 10 watts using a 2.5 V power supply.
a. Using fixed voltage scaling, what will the speed and power consumption of the same processor be if scaled to 0.1 µm technology?
b. If the supply voltage on the 0.1 µm part were scaled to 1.0 V, what will the power consumption and speed be?
c. What supply should be used to fix the power consumption at 10 watts? At what speed
would the processor operate?
1
Chapter 4 Problem Set
Chapter 4
Problems
1.
[M, None, 4.x] Figure 0.1 shows a clock-distribution network. Each segment of the clock network (between the nodes) is 5 mm long, 3 µm wide, and is implemented in polysilicon. At
each of the terminal nodes (such as R) resides a load capacitance of 100 fF.
a. Determine the average current of the clock driver, given a voltage swing on the clock lines
of 5 V and a maximum delay of 5 nsec between clock source and destination node R. For
this part, you may ignore the resistance and inductance of the network
b. Unfortunately the resistance of the polysilicon cannot be ignored. Assume that each
straight segment of the network can be modeled as a Π-network. Draw the equivalent circuit and annotate the values of resistors and capacitors.
c. Determine the dominant time-constant of the clock response at node R.
S
Figure 0.1
Clock-distribution network.
R
2.
3.
[C, SPICE, 4.x] You are designing a clock distribution network in which it is critical to minimize skew between local clocks (CLK1, CLK2, and CLK3). You have extracted the RC network of Figure 0.2, which models the routing parasitics of your clock line. Initially, you
notice that the path to CLK3 is shorter than to CLK1 or CLK2. In order to compensate for this
imbalance, you insert a transmission gate in the path of CLK3 to eliminate the skew.
a. Write expressions for the time-constants associated with nodes CLK1, CLK2 and CLK3.
Assume the transmission gate can be modeled as a resistance R3.
b. If R1 = R2 = R4 = R5 = R and C1 = C2 = C3 = C4 = C5 = C, what value of R3 is required to
balance the delays to CLK1, CLK2, and CLK3?
c. For R = 750Ω and C = 200fF, what (W/L)’s are required in the transmission gate to eliminate skew? Determine the value of the propagation delay.
d. Simulate the network using SPICE, and compare the obtained results with the manually
obtained numbers.
[M, None, 4.x]Consider a CMOS inverter followed by a wire of length L. Assume that in the
reference design, inverter and wire contribute equally to the total propagation delay tpref. You
may assume that the transistors are velocity-saturated. The wire is scaled in line with the ideal
wire scaling model. Assume initially that the wire is a local wire.
a. Determine the new (total) propagation delay as a a function of tpref, assuming that technology and supply voltage scale with a factor 2. Consider only first-order effects.
b. Perform the same analysis, assuming now that the wire scales a global wire, and the wire
length scales inversely proportional to the technology.
2
Chapter 4 Problem Set
R4
CLK1
R2
C4
R5
Clock
driver
C2
R1
CLK2
C5
C1
CLK3
C3
Model as:
R3
4.
5.
Figure 0.2
network.
RC clock-distribution
c. Repeat b, but assume now that the wire is scaled along the constant resistance model. You
may ignore the effect of the fringing capacitance.
d. Repeat b, but assume that the new technology uses a better wiring material that reduces
the resistivity by half, and a dielectric with a 25% smaller permittivity.
e. Discuss the energy dissipation of part a. as a function of the energy dissipation of the original design Eref.
f. Determine for each of the statements below if it is true, false, or undefined, and explain in
one line your answer.
- When driving a small fan-out, increasing the driver transistor sizes raises the shortcircuit power dissipation.
- Reducing the supply voltage, while keeping the threshold voltage constant decreases
the short-circuit power dissipation.
- Moving to Copper wires on a chip will enable us to build faster adders.
- Making a wire wider helps to reduce its RC delay.
- Going to dielectrics with a lower permittivity will make RC wire delay more important.
[M, None, 4.x] A two-stage buffer is used to drive a metal wire of 1 cm. The first inverter is of
minimum size with an input capacitance Ci=10 fF and an internal propagation delay tp0=50 ps
and load dependent delay of 5ps/fF. The width of the metal wire is 3.6 µm. The sheet resistance of the metal is 0.08 Ω/ , the capacitance value is 0.03 fF/µm2 and the fringing field
capacitance is 0.04fF/µm.
a. What is the propagation delay of the metal wire?
b. Compute the optimal size of the second inverter. What is the minimum delay through the
buffer?
c. If the input to the first inverter has 25% chance of making a 0-to-1 transition, and the
whole chip is running at 20MHz with a 2.5 supply voltage, then what’s the power consumed by the metal wire?
[M, None, 4.x]To connect a processor to an external memory an off -chip connection is necessary. The copper wire on the board is 15 cm long and acts as a transmission line with a characteristic impedance of 100Ω.(See Figure 0.3). The memory input pins present a very high
impedance which can be considered infinite. The bus driver is a CMOS inverter consisting of
very large devices: (50/0.25) for the NMOS and (150/0.25) for the PMOS, where all sizes are
Digital Integrated Circuits - 2nd Ed
3
in µm. The minimum size device, (0.25/0.25) for NMOS and (0.75/0.25) for PMOS, has the
on resistance 35 kΩ.
a. Determine the time it takes for a change in the signal to propagate from source to destination (time of flight). The wire inductance per unit length equals 75*10-8 H/m.
b. Determine how long it will take the output signal to stay within 10% of its final value. You
can model the driver as a voltage source with the driving device acting as a series resistance. Assume a supply and step voltage of 2.5V. Hint: draw the lattice diagram for the
transmission line.
c. Resize the dimensions of the driver to minimize the total delay.
L=15cm
Memory
Z=100Ω
Figure 0.3 The driver, the connecting copper wire and the
memory block being accessed.
6.
7.
[M, None, 4.x] A two stage buffer is used to drive a metal wire of 1 cm. The first inverter is a
minimum size with an input capacitance Ci=10 fF and a propagation delay tp0=175 ps when
loaded with an identical gate. The width of the metal wire is 3.6 µm. The sheet resistance of
the metal is 0.08 Ω/ , the capacitance value is 0.03 fF/µm2 and the fringing field capacitance
is 0.04 fF/µm.
a. What is the propagation delay of the metal wire?
b. Compute the optimal size of the second inverter. What is the minimum delay through the
buffer?
[M, None, 4.x] For the RC tree given in Figure 0.4 calculate the Elmore delay from node A to
node B using the values for the resistors and capacitors given in the below in Table 0.1.
Figure 0.4
RC tree for calculating the delay
4
Chapter 4 Problem Set
Table 0.1
8.
Values of the components in the RC tree of Figure 0.4
Resistor
Value(Ω)
Capacitor
Value(fF)
R1
0.25
C1
250
R2
0.25
C2
750
R3
0.50
C3
250
R4
100
C4
250
R5
0.25
C5
1000
R6
1.00
C6
250
R7
0.75
C7
500
R8
1000
C8
250
[M, SPICE, 4.x] In this problem the various wire models and their respective accuracies will
be studied.
a. Compute the 0%-50% delay of a 500um x 0.5um wire with resistance of 0.08 Ω/ , with
area capacitance of 30aF/um2, and fringing capacitance of 40aF/um. Assume the driver
has a 100Ω resistance and negligible output capacitance.
• Using a lumped model for the wire.
• Using a PI model for the wire, and the Elmore equations to find tau. (see Chapter 4, figure
4.26).
• Using the distributed RC line equations from Chapter 4, section 4.4.4.
b. Compare your results in part a. using spice (be sure to include the source resistance). For
each simulation, measure the 0%-50% time for the output
• First, simulate a step input to a lumped R-C circuit.
• Next, simulate a step input to your wire as a PI model.
• Unfortunately, our version of SPICE does not support the distributed RC model as
described in your book (Chapter 4, section 4.5.1). Instead, simulate a step input to your
wire using a PI3 distributed RC model.
9.
[M, None, 4.x] A standard CMOS inverter drives an aluminum wire on the first metal layer.
Assume Rn=4kΩ, Rp=6kΩ. Also, assume that the output capacitance of the inverter is negligible in comparison with the wire capacitance. The wire is .5um wide, and the resistivity is
0.08 Ω/ ..
a. What is the "critical length" of the wire?
b. What is the equivalent capacitance of a wire of this length? (For your capacitance calculations, use Table 4.2 of your book , assume there’s field oxide underneath and nothing
above the aluminum wire)
Digital Integrated Circuits - 2nd Ed
10.
11.
5
[M, None, 4.x] A 10cm long lossless transmission line on a PC board (relative dielectric constant = 9, relative permeability = 1) with characteristic impedance of 50Ω is driven by a 2.5V
pulse coming from a source with 150Ω resistance.
a. If the load resistance is infinite, determine the time it takes for a change at the source to
reach the load (time of flight).
Now a 200Ω load is attached at the end of the transmission line.
b. What is the voltage at the load at t = 3ns?
c. Draw lattice diagram and sketch the voltage at the load as a function of time. Determine
how long does it take for the output to be within 1 percent of its final value.
[C, SPICE, 4.x] Assume VDD=1.5V. Also, use short-channel transistor models forhand analysis.
VDD
VDD
L=350nH/m
C=150pF/m
in
VS
10cm
VL
Figure 0.5 Transmission line
between two inverters
CL=0.2pF
12.
13.
a. The Figure 0.5 shows an output driver feeding a 0.2 pF effective fan-out of CMOS gates
through a transmission line. Size the two transistors of the driver to optimize the delay.
Sketch waveforms of VS and VL, assuming a square wave input. Label critical voltages
and times.
b. Size down the transistors by m times (m is to be treated as a parameter). Derive a first
order expression for the time it takes for VL to settle down within 10% of its final voltage
level.Compare the obtained result with the case where no inductance is associated with the
wire.Please draw the waveforms of VL for both cases, and comment.
c. Use the transistors as in part a). Suppose CL is changed to 20pF. Sketch waveforms of VS
and VL, assuming a square wave input. Label critical voltages and instants.
d. Assume now that the transmission line is lossy. Perform Hspice simulation for three cases:
R=100 Ω/cm; R=2.5 Ω/cm; R=0.5 Ω/cm. Get the waveforms of VS, VL and the middle
point of the line. Discuss the results.
[M, None, 4.x] Consider an isolated 2mm long and 1µm wide M1(Metal1)wire over a silicon
substrate driven by an inverter that has zero resistance and parasitic output capccitance. How
will the wire delay change for the following cases? Explain your reasoning in each case.
a. If the wire width is doubled.
b. If the wire length is halved.
c. If the wire thickness is doubled.
d. If thickness of the oxide between the M1 and the substrate is doubled.
[E, None, 4.x] In an ideal scaling model, where all dimensions and voltages scale with a factor of S >1 :
6
Chapter 4 Problem Set
a. How does the delay of an inverter scale?
b. If a chip is scaled from one technology to another where all wire dimensions,including the
vertical one and spacing, scale with a factor of S, how does the wire delayscale? How does
the overall operating frequency of a chip scale?
c. Repeat b) for the case where everything scales, except the vertical dimension of wires (it
stays constant).
CHAPTER
5
THE CMOS INVERTER
Quantification of integrity, performance, and energy metrics of an inverter
Optimization of an inverter design
5.1
Exercises and Design Problems
5.4.2
5.2
The Static CMOS Inverter — An Intuitive
Perspective
Propagation Delay: First-Order
Analysis
5.4.3
Propagation Delay from a Design
Perspective
5.3
Evaluating the Robustness of the CMOS
Inverter: The Static Behavior
Switching Threshold
5.5.1
Dynamic Power Consumption
5.3.2
Noise Margins
5.5.2
Static Consumption
Robustness Revisited
5.5.3
Putting It All Together
5.5.4
Analyzing Power Consumption Using
SPICE
Performance of CMOS Inverter: The Dynamic
Behavior
5.4.1
180
Power, Energy, and Energy-Delay
5.3.1
5.3.3
5.4
5.5
Computing the Capacitances
5.6
Perspective: Technology Scaling and its
Impact on the Inverter Metrics
Section 5.1
181
Exercises and Design Problems
1.
[M, SPICE, 3.3.2] The layout of a static CMOS inverter is given in Figure 5.1. (λ = 0.125
µm).
a. Determine the sizes of the NMOS and PMOS transistors.
b. Plot the VTC (using HSPICE) and derive its parameters (VOH, VOL, VM, VIH, and VIL).
c. Is the VTC affected when the output of the gates is connected to the inputs of 4 similar
gates?.
GND
Poly
In
VDD = 2.5 V.
Poly
2λ
5.1
Exercises and Design Problems
PMOS
NMOS
Metal1
Out
Metal1
Figure 5.1
2.
CMOS inverter layout.
d. Resize the inverter to achieve a switching threshold of approximately 0.75 V. Do not layout the new inverter, use HSPICE for your simulations. How are the noise margins
affected by this modification?
Figure 5.2 shows a piecewise linear approximation for the VTC. The transition region is
approximated by a straight line with a slope equal to the inverter gain at VM. The intersection
of this line with the VOH and the VOL lines defines VIH and VIL.
a. The noise margins of a CMOS inverter are highly dependent on the sizing ratio, r = kp/kn,
of the NMOS and PMOS transistors. Use HSPICE with VTn = |VTp| to determine the value
of r that results in equal noise margins? Give a qualitative explanation.
b. Section 5.3.2 of the text uses this piecewise linear approximation to derive simplified
expressions for NMH and NML in terms of the inverter gain. The derivation of the gain is
based on the assumption that both the NMOS and the PMOS devices are velocity saturated
at VM . For what range of r is this assumption valid? What is the resulting range of VM ?
c. Derive expressions for the inverter gain at VM for the cases when the sizing ratio is just
above and just below the limits of the range where both devices are velocity saturated.
What are the operating regions of the NMOS and the PMOS for each case? Consider the
effect of channel-length modulation by using the following expression for the small-signal
resistance in the saturation region: ro,sat = 1/(λID).
182
THE CMOS INVERTER
Chapter 5
Vout
VOH
VM
Vin
VOL
3.
VIL
VIH
Figure 5.2 A different approach to derive
VIL and VIH.
[M, SPICE, 3.3.2] Figure 5.3 shows an NMOS inverter with resistive load.
a. Qualitatively discuss why this circuit behaves as an inverter.
b. Find VOH and VOL calculate VIH and VIL.
c. Find NML and NMH, and plot the VTC using HSPICE.
d. Compute the average power dissipation for: (i) Vin = 0 V and (ii) Vin = 2.5 V
+2.5 V
RL = 75 kΩ
Vout
Vin
M1
W/L = 1.5/0.5
Figure 5.3
4.
5.
Resistive-load inverter
e. Use HSPICE to sketch the VTCs for RL = 37k, 75k, and 150k on a single graph.
f. Comment on the relationship between the critical VTC voltages (i.e., VOL, VOH, VIL, VIH )
and the load resistance, RL.
g. Do high or low impedance loads seem to produce more ideal inverter characteristics?
[E, None, 3.3.3] For the inverter of Figure 5.3 and an output load of 3 pF:
a. Calculate tplh, tphl, and tp.
b. Are the rising and falling delays equal? Why or why not?
c. Compute the static and dynamic power dissipation assuming the gate is clocked as fast as
possible.
The next figure shows two implementations of MOS inverters. The first inverter uses only
NMOS transistors.
Section 5.1
Exercises and Design Problems
183
a. Calculate VOH, VOL, VM for each case.
VDD = 2.5V
V DD = 2.5V
M2
M4 W/L=0.75/0.25
W/L=0.375/0.25
VOUT
V OUT
VIN
VIN
M3 W/L=0.375/0.25
M1 W/L=0.75/0.25
Figure 5.4 Inverter Implementations
6.
b. Use HSPICE to obtain the two VTCs. You must assume certain values for the source/drain
areas and perimeters since there is no layout. For our scalable CMOS process, λ = 0.125
µm, and the source/drain extensions are 5λ for the PMOS; for the NMOS the source/drain
contact regions are 5λx5λ.
c. Find VIH , VIL, NM L and NMH for each inverter and comment on the results. How can you
increase the noise margins and reduce the undefined region?
d. Comment on the differences in the VTCs, robustness and regeneration of each inverter.
Consider the following NMOS inverter. Assume that the bulk terminals of all NMOS device
are connected to GND. Assume that the input IN has a 0V to 2.5V swing.
VDD= 2.5V
VDD= 2.5V
M3
x
M2
OUT
IN
a.
b.
c.
d.
M1
Set up the equation(s) to compute the voltage on node x. Assume γ=0.5.
What are the modes of operation of device M2? Assume γ=0.
What is the value on the output node OUT for the case when IN =0V?Assume γ=0.
Assuming γ=0, derive an expression for the switching threshold (VM) of the inverter.
Recall that the switching threshold is the point where VIN= VOUT. Assume that the device
sizes for M1, M2 and M3 are (W/L)1, (W/L)2, and (W/L)3 respectively. What are the limits
on the switching threshold?
For this, consider two cases:
i) (W/L)1 >> (W/L)2
184
THE CMOS INVERTER
7.
Chapter 5
ii) (W/L)2 >> (W/L)1
Consider the circuit in Figure 5.5. Device M1 is a standard NMOS device. Device M2 has all
the same properties as M1, except that its device threshold voltage is negative and has a value
of -0.4V. Assume that all the current equations and inequality equations (to determine the
mode of operation) for the depletion device M2 are the same as a regular NMOS. Assume that
the input IN has a 0V to 2.5V swing.
VDD= 2.5 V
M2 (2µm/1µm), VTn = -0.4V
OUT
IN
M1 (4µm/1µm)
Figure 5.5 A depletion load NMOS inverter
8.
a. Device M2 has its gate terminal connected to its source terminal. If VIN = 0V, what is the
output voltage? In steady state, what is the mode of operation of device M2 for this input?
b. Compute the output voltage for VIN = 2.5V. You may assume that VOUT is small to simplify
your calculation. In steady state, what is the mode of operation of device M2 for this
input?
c. Assuming Pr(IN =0)= 0.3, what is the static power dissipation of this circuit?
[M, None, 3.3.3] An NMOS transistor is used to charge a large capacitor, as shown in Figure
5.6.
a. Determine the tpLH of this circuit, assuming an ideal step from 0 to 2.5V at the input node.
b. Assume that a resistor RS of 5 kΩ is used to discharge the capacitance to ground. Determine tpHL.
c. Determine how much energy is taken from the supply during the charging of the capacitor.
How much of this is dissipated in M1. How much is dissipated in the pull-down resistance
during discharge? How does this change when RS is reduced to 1 kΩ.
d. The NMOS transistor is replaced by a PMOS device, sized so that kp is equal to the kn of
the original NMOS. Will the resulting structure be faster? Explain why or why not.
VDD = 2.5V
In
20
2 M1
Out
CL = 5 pF
Figure 5.6 Circuit diagram with annotated W/L ratios
9.
The circuit in Figure 5.7 is known as the source follower configuration. It achieves a DC level
shift between the input and the output. The value of this shift is determined by the current I0.
Assume xd=0, γ=0.4, 2|φf|=0.6V, VT0=0.43V, kn’=115µA/V2 and λ=0.
Section 5.1
Exercises and Design Problems
185
VDD = 2.5V
VDD = 2.5V
Io
Vi
M1 1um/0.25um
Vi
M1 1um/0.25um
Vo
Vo
Vbias= 0.55V
M2
LD=1um
Io
(a)
(b)
Figure 5.7 NMOS source follower configuration
10.
a. Suppose we want the nominal level shift between Vi and Vo to be 0.6V in the circuit in
Figure 5.7 (a). Neglecting the backgate effect, calculate the width of M2 to provide this
level shift (Hint: first relate Vi to Vo in terms of Io).
b. Now assume that an ideal current source replaces M2 (Figure 5.7 (b)). The NMOS transistor M1 experiences a shift in VT due to the backgate effect. Find VT as a function of Vo for
Vo ranging from 0 to 2.5V with 0.5V intervals. Plot VT vs. Vo
c. Plot Vo vs. Vi as Vo varies from 0 to 2.5V with 0.5 V intervals. Plot two curves: one
neglecting the body effect and one accounting for it. How does the body effect influence
the operation of the level converter?
d. At Vo(with body effect) = 2.5V, find Vo(ideal) and thus determine the maximum error
introduced by the body effect.
For this problem assume:
VDD = 2.5V, W P/L = 1.25/0.25, WN/L = 0.375/0.25, L=Leff =0.25µm (i.e. xd= 0µm), CL=Cinv2
2
-1
gate, kn’ = 115µA/V , kp’= -30µA/V , Vtn0 = | Vtp0 | = 0.4V, λ = 0V , γ = 0.4, 2|φf|=0.6V, and tox
= 58A. Use the HSPICE model parameters for parasitic capacitance given below (i.e. Cgd0, Cj,
Cjsw), and assume that VSB=0V for all problems except part (e).
186
THE CMOS INVERTER
Chapter 5
VDD = 2.5V
L = LP = LN = 0.25µm
VOUT
VIN
CL = Cinv-gate
(Wp/Wn = 1.25/0.375)
+
VSB
Figure 5.8 CMOS inverter with capacitive
11.
## Parasitic Capacitance Parameters (F/m)##
NMOS: CGDO=3.11x10-10, CGSO=3.11x10-10, CJ=2.02x10-3, CJSW=2.75x10-10
PMOS: CGDO=2.68x10-10, CGSO=2.68x10-10, CJ=1.93x10-3, CJSW=2.23x10-10
a. What is the Vm for this inverter?
b. What is the effective load capacitance CLeff of this inverter? (include parasitic capacitance,
refer to the text for Keq and m.) Hint: You must assume certain values for the source/drain
areas and perimeters since there is no layout. For our scalable CMOS process, λ = 0.125
µm, and the source/drain extensions are 5λ for the PMOS; for the NMOS the source/drain
contact regions are 5λx5λ.
c. Calculate tPHL, tPLH assuming the result of (b) is ‘CLeff = 6.5fF’. (Assume an ideal step
input, i.e. trise=tfall=0. Do this part by computing the average current used to charge/discharge CLeff.)
d. Find (Wp/Wn) such that tPHL = tPLH.
e. Suppose we increase the width of the transistors to reduce the tPHL, tPLH. Do we get a proportional decrease in the delay times? Justify your answer.
f. Suppose VSB = 1V, what is the value of Vtn, Vtp, Vm? How does this qualitatively affect
CLeff?
Using Hspice answer the following questions.
a. Simulate the circuit in Problem 10 and measure tP and the average power for input Vin:
pulse(0 VDD 5n 0.1n 0.1n 9n 20n), as VDD varies from 1V - 2.5V with a 0.25V interval. [tP
= (tPHL + tPLH ) / 2]. Using this data, plot ‘tP vs. VDD’, and ‘Power vs. VDD’.
Specify AS, AD, PS, PD in your spice deck, and manually add CL = 6.5fF. Set VSB = 0V
for this problem.
b. For Vdd equal to 2.5V determine the maximum fan-out of identical inverters this gate can
drive before its delay becomes larger than 2 ns.
c. Simulate the same circuit for a set of ‘pulse’ inputs with rise and fall times of tin_rise,fall
=1ns, 2ns, 5ns, 10ns, 20ns. For each input, measure (1) the rise and fall times tout_rise and
Section 5.1
12.
Exercises and Design Problems
187
tout_fall of the inverter output, (2) the total energy lost Etotal, and (3) the energy lost due to
short circuit current Eshort.
Using this data, prepare a plot of (1) (tout_rise+tout_fall)/2 vs. tin_rise,fall, (2) Etotal vs.
tin_rise,fall, (3) Eshort vs. tin_rise,fall and (4) Eshort/Etotal vs. tin_rise,fall.
d. Provide simple explanations for:
(i) Why the slope for (1) is less than 1?
(ii) Why Eshort increases with tin_rise,fall?
(iii) Why Etotal increases with tin_rise,fall?
Consider the low swing driver of Figure 5.9:
VDD = 2.5 V
W
= 1.5 µm
L n 0.25 µm
W
3 µm
=
L p 0.25 µm
Vin
Vout
2.5V
CL=100fF
0V
Figure 5.9 Low Swing Driver
13.
a. What is the voltage swing on the output node (Vout)? Assume γ=0.
b. Estimate (i) the energy drawn from the supply and (ii) energy dissipated for a 0V to 2.5V
transition at the input. Assume that the rise and fall times at the input are 0. Repeat the
analysis for a 2.5V to 0V transition at the input.
c. Compute tpLH (i.e. the time to transition from VOL to (VOH + VOL) /2). Assume the input
rise time to be 0. VOL is the output voltage with the input at 0V and VOH is the output voltage with the input at 2.5V.
d. Compute VOH taking into account body effect. Assume γ = 0.5V1/2 for both NMOS and
PMOS.
Consider the following low swing driver consisting of NMOS devices M1 and M2. Assume
an NWELL implementation. Assume that the inputs IN and IN have a 0V to 2.5V swing and
that VIN = 0V when VIN = 2.5V and vice-versa. Also assume that there is no skew between IN
and IN (i.e., the inverter delay to derive IN from IN is zero).
VLOW= 0.5V
IN
25µm/0.25µm
M2
Out
IN
M1
25µm/0.25µm
CL=1pF
Figure 5.10 Low Swing Driver
a. What voltage is the bulk terminal of M2 connected to?
188
THE CMOS INVERTER
Chapter 5
b. What is the voltage swing on the output node as the inputs swing from 0V to 2.5V. Show
the low value and the high value.
c. Assume that the inputs IN and IN have zero rise and fall times. Assume a zero skew
between IN and IN. Determine the low to high propagation delay for charging the output
node measured from the the 50% point of the input to the 50% point of the output. Assume
that the total load capacitance is 1pF, including the transistor parasitics.
d. Assume that, instead of the 1pF load, the low swing driver drives a non-linear capacitor,
whose capacitance vs. voltage is plotted below. Compute the energy drawn from the low
supply for charging up the load capacitor. Ignore the parasitic capacitance of the driver circuit itself.
3
2
1
.5V 1V 1.5V 2V 2.5V 3V
14.
Voltage, V
The inverter below operates with VDD=0.4V and is composed of |V t| = 0.5V devices. The
devices have identical I0 and n.
a. Calculate the switching threshold (VM) of this inverter.
b. Calculate VIL and VIH of the inverter.
VDD = 0.4V
VIN
VOUT
Figure 5.11 Inverter in Weak Inversion Regime
15.
Sizing a chain of inverters.
a. In order to drive a large capacitance (CL = 20 pF) from a minimum size gate (with input
capacitance Ci = 10fF), you decide to introduce a two-staged buffer as shown in Figure
5.12. Assume that the propagation delay of a minimum size inverter is 70 ps. Also assume
Section 5.1
Exercises and Design Problems
189
that the input capacitance of a gate is proportional to its size. Determine the sizing of the
two additional buffer stages that will minimize the propagation delay.
‘1’ is the minimum size inverter.
In
OUT
1
?
?
Ci = 10fF
CL = 20pF
Added Buffer Stage
Figure 5.12 Buffer insertion for driving large loads.
16.
b. If you could add any number of stages to achieve the minimum delay, how many stages
would you insert? What is the propagation delay in this case?
c. Describe the advantages and disadvantages of the methods shown in (a) and (b).
d. Determine a closed form expression for the power consumption in the circuit. Consider
only gate capacitances in your analysis. What is the power consumption for a supply voltage of 2.5V and an activity factor of 1?
[M, None, 3.3.5] Consider scaling a CMOS technology by S > 1. In order to maintain compatibility with existing system components, you decide to use constant voltage scaling.
a. In traditional constant voltage scaling, transistor widths scale inversely with S, W∝1/S.
To avoid the power increases associated with constant voltage scaling, however, you
decide to change the scaling factor for W. What should this new scaling factor be to maintain approximately constant power. Assume long-channel devices (i.e., neglect velocity
saturation).
b. How does delay scale under this new methodology?
c. Assuming short-channel devices (i.e., velocity saturation), how would transistor widths
have to scale to maintain the constant power requirement?
190
THE CMOS INVERTER
DESIGN PROBLEM
Using the 0.25 µm CMOS introduced in Chapter 2, design a static CMOS
inverter that meets the following requirements:
1. Matched pull-up and pull-down times (i.e., tpHL = tpLH).
2. tp = 5 nsec (± 0.1 nsec).
The load capacitance connected to the output is equal to 4 pF. Notice that this
capacitance is substantially larger than the internal capacitances of the gate.
Determine the W and L of the transistors. To reduce the parasitics, use
minimal lengths (L = 0.25 µm) for all transistors. Verify and optimize the design
using SPICE after proposing a first design using manual computations. Compute also the energy consumed per transition. If you have a layout editor (such
as MAGIC) available, perform the physical design, extract the real circuit
parameters, and compare the simulated results with the ones obtained earlier.
Chapter 5
Chapter 6 Problem Set
1
Chapter 6
PROBLEMS
1.
2.
[E, None, 4.2] Implement the equation X = ((A + B) (C + D + E) + F) G using complementary CMOS. Size the devices so that the output resistance is the same as that of an inverter
with an NMOS W/L = 2 and PMOS W/L = 6. Which input pattern(s) would give the worst and
best equivalent pull-up or pull-down resistance?
Implement the following expression in a full static CMOS logic fashion using no more than
10 transistors:
Y = (A ⋅ B) + (A ⋅ C ⋅ E) + (D ⋅ E) + (D ⋅ C ⋅ B)
3.
Consider the circuit of Figure 6.1.
VDD
B
D
A
C
Y
B
A
C
D
Figure 6.1 CMOS combinational logic gate.
4.
a. What is the logic function implemented by the CMOS transistor network? Size the NMOS
and PMOS devices so that the output resistance is the same as that of an inverter with an
NMOS W/L = 4 and PMOS W/L = 8.
b. What are the input patterns that give the worst case tpHL and tpLH. State clearly what are the
initial input patterns and which input(s) has to make a transition in order to achieve this
maximum propagation delay. Consider the effect of the capacitances at the internal nodes.
c. Verify part (b) with SPICE. Assume all transistors have minimum gate length (0.25µm).
d. If P(A=1)=0.5, P(B=1)=0.2, P(C=1)=0.3 and P(D=1)=1, determine the power dissipation
in the logic gate. Assume VDD=2.5V, Cout=30fF and fclk=250MHz.
[M, None, 4.2] CMOS Logic
a. Do the following two circuits (Figure 6.2) implement the same logic function? If yes, what
is that logic function? If no, give Boolean expressions for both circuits.
b. Will these two circuits’ output resistances always be equal to each other?
c. Will these two circuits’ rise and fall times always be equal to each other? Why or why not?
Chapter 6 Problem Set
2
VDD
E
VDD
6
A
A
6 B
6
6 D
C
6 B
6 C
6 D
6
E
6
F
A
4
B
4
C
4
D
4
F
1
E
A
4
B
4
C
4
D
4
Circuit A
5.
6.
1
Figure 6.2 Two static
CMOS gates.
[E, None, 4.2] The transistors in the circuits of the preceding problem have been sized to give
an output resistance of 13 kΩ for the worst-case input pattern. This output resistance can vary,
however, if other patterns are applied.
a. What input patterns (A–E) give the lowest output resistance when the output is low? What
is the value of that resistance?
b. What input patterns (A–E) give the lowest output resistance when the output is high? What
is the value of that resistance?
[E, None, 4.2] What is the logic function of circuits A and B in Figure 6.3? Which one is a
dual network and which one is not? Is the nondual network still a valid static logic gate?
Explain. List any advantages of one configuration over the other.
VDD
A
B
B
A
F
A
B
B
A
F
B
B
B
B
A
A
A
A
Circuit A
8.
E
Circuit B
VDD
7.
6
Circuit B
Figure 6.3 Two logic functions.
[E, None, 4.2] Compute the following for the pseudo-NMOS inverter shown in Figure 6.4:
a. VOL and VOH
b. NML and NMH
c. The power dissipation: (1) for Vin low, and (2) for Vin high
d. For an output load of 1 pF, calculate tpLH, tpHL, and tp. Are the rising and falling delays
equal? Why or why not?
[M, SPICE, 4.2] Consider the circuit of Figure 6.5.
Digital Integrated Circuits - 2nd Ed
3
2.5 V
PMOS
M2 W/L = 0.5µm/0.25µm
Vout
Vin
M1 W/L = 4µm/0.25µm
NMOS
Figure 6.4 Pseudo-NMOS inverter.
a. What is the output voltage if only one input is high? If all four inputs are high?
b. What is the average static power consumption if, at any time, each input turns on with an
(independent) probability of 0.5? 0.1?
c. Compare your analytically obtained results to a SPICE simulation.
VDD
(W/L) = 0.6
F
A
B
C
D
(W/L) = 1.5
Figure 6.5 Pseudo-NMOS gate.
9.
10.
[M, None, 4.2] Implement F = ABC + ACD (and F) in DCVSL. Assume A, B, C, D, and their
complements are available as inputs. Use the minimum number of transistors.
[E, Layout, 4.2] A complex logic gate is shown in Figure 6.6.
a. Write the Boolean equations for outputs F and G. What function does this circuit
implement?
b. What logic family does this circuit belong to?
c. Assuming W/L = 0.5u/0.25u for all nmos transistors and W/L = 2u/0.25u for the pmos transistors, produce a layout of the gate using Magic. Your layout should conform to the following datapath style: (1) Inputs should enter the layout from the left in polysilicon; (2)
The outputs should exit the layout at the right in polysilicon (since the outputs would probably be driving transistor gate inputs of the next cell to the right); (3) Power and ground
lines should run vertically in metal 1.
d. Extract and netlist the layout. Load both outputs (F,G) with a 30fF capacitance and simulate the circuit. Does the gate function properly? If not, explain why and resize the transistors so that it does. Change the sizes (and areas and perimeters) in the HSPICE netlist.
Chapter 6 Problem Set
4
VDD
F
G
A
A
A
A
B
B
Figure 6.6 Two-input complex logic gate.
11.
Design and simulate a circuit that generates an optimal differential signal as shown in Figure
6.7. Make sure the rise and fall times are equal.
Y
A
Y
A Y Y
0 0 1
1 1 0
Y
Y
50% of VDD
Figure 6.7 Differential Buffer.
12.
What is the function of the circuit in Figure 6.8?
A
Y
B
Y
Figure 6.8 Gate.
13.
14.
Implement the function S = ABC + ABC + ABC + ABC, which gives the sum of two inputs
with a carry bit, using NMOS pass transistor logic. Design a DCVSL gate which implements
the same function. Assume A, B, C, and their complements are available as inputs.
Describe the logic function computed by the circuit in Figure 6.9. Note that all transistors
(except for the middle inverters) are NMOS. Size and simulate the circuit so that it achieves a
Digital Integrated Circuits - 2nd Ed
5
100 ps delay (50-50) using 0.25µm devices, while driving a 100 fF load on both differential
outputs. (VDD = 2.5V) Assume A, B and their complements are available as inputs.
Y
Y
A
A
A
A
B
B
B
B
A
A
A
A
B
B
B
B
Figure 6.9 Cascoded Logic Styles.
15.
For the drain and source perimeters and areas you can use the following approximations: AS=AD=W*0.625u and PS=PD=W+1.25u.
[M, None. 4.2] Figure 6.10 contains a pass-gate logic network.
a. Determine the truth table for the circuit. What logic function does it implement?
b. Assuming 0 and 2.5 V inputs, size the PMOS transistor to achieve a VOL = 0.3 V.
c. If the PMOS were removed, would the circuit still function correctly? Does the PMOS
transistor serve any useful purpose?
A
1.5/.25
B
16.
17.
Out
Figure 6.10 Pass-gate network.
[M, None, 4.2] This problem considers the effects of process scaling on pass-gate logic.
a. If a process has a tbuf of 0.4 ns, Req of 8 kΩ, and C of 12 fF, what is the optimal number of
stages between buffers in a pass-gate chain?
b. Suppose that, if the dimension of this process are shrunk by a factor S, Req scales as 1/S2, C
scales as 1/S, and tbuf scales as 1/S2. What is the expression for the optimal number of buffers as a function of S? What is this value if S = 2?
[C, None, 4.2] Consider the circuit of Figure 6.11. Let Cx = 50 fF, Mr has W/L = 0.375/0.375,
Mn has W/Leff = 0.375/0.25. Assume the output inverter doesn’t switch until its input equals
VDD/2.
a. How long will it take Mn to pull down node x from 2.5 V to 1.25 V if In is at 0 V and B is
at 2.5V?
b. How long will it take Mn to pull up node x from 0 V to 1.25 V if VIn is 2.5 V and VB is
2.5 V?
c. What is the minimum value of VB necessary to pull down Vx to 1.25 V when VIn = 0 V?
Chapter 6 Problem Set
6
VDD
VDD
Mr
B
M2
In
x
Mn
Out
M1
Figure 6.11 Level restorer.
18.
Pass Transistor Logic
pass transistor network
VDD
VDD = 2.5V
B
M2
A
Mn1
B
x
Out
M1
(W/L)2 = 1.5um/0.25um
(W/L)1 = 0.5um/0.25um
(W/L)ni = 0.5um/0.25um
kn’ = 115uA/V2, kp’ = -30uA/V2
VtN = 0.43V, VtP = -0.4V
Mn2
Figure 6.12 Level restoring circuit.
19.
20.
21.
Consider the circuit of Figure 6.12. Assume the inverter switches ideally at VDD/2, neglect
body effect, channel length modulation and all parasitic capacitance throughout this problem.
a. What is the logic function performed by this circuit?
b. Explain why this circuit has non-zero static dissipation.
c. Using only just 1 transistor, design a fix so that there will not be any static power dissipation. Explain how you chose the size of the transistor.
d. Implement the same circuit using transmission gates.
e. Replace the pass-transistor network in Figure 6.12 with a pass transistor network that
computes the following function: x = ABC at the node x. Assume you have the true and
complementary versions of the three inputs A,B and C.
[M, None, 4.3] Sketch the waveforms at x, y, and z for the given inputs (Figure 6.13). You
may approximate the time scale, but be sure to compute the voltage levels. Assume that
VT = 0.5 V when body effect is a factor.
[E, None, 4.3] Consider the circuit of Figure 6.14.
a. Give the logic function of x and y in terms of A, B, and C. Sketch the waveforms at x and y
for the given inputs. Do x and y evaluate to the values you expected from their logic functions? Explain.
b. Redesign the gates using np-CMOS to eliminate any race conditions. Sketch the waveforms at x and y for your new circuit.
[M, None, 4.3] Suppose we wish to implement the two logic functions given by
F = A + B + C and G = A + B + C + D. Assume both true and complementary signals are
available.
Digital Integrated Circuits - 2nd Ed
7
VDD
2.5 V
φ
A
φ
0V
2.5 V
Mp
x
0V
2.5 V
A
Ma
B
Mb
CL = 100 fF
y
B
0V
Ca = 10 fF
z
φ
Cb = 10 fF
Mn
Figure 6.13 Dynamic CMOS.
VDD
2.5 V
φ
0V
2.5 V
A
2.5 V
B
φ
C
0V
φ
A
φ
y
x
C
φ
B
Figure 6.14 Cascaded dynamic gates.
a. Implement these functions in dynamic CMOS as cascaded φ stages so as to minimize the
total transistor count.
b. Design an np-CMOS implementation of the same logic functions. Does this design display
any of the difficulties of part (a)?
22. Consider a conventional 4-stage Domino logic circuit as shown in Figure 6.15 in which all
precharge and evaluate devices are clocked using a common clock φ. For this entire problem,
assume that the pulldown network is simply a single NMOS device, so that each Domino
stage consists of a dynamic inverter followed by a static inverter. Assume that the precharge
time, evaluate time, and propagation delay of the static inverter are all T/2. Assume that the
transitions are ideal (zero rise/fall times).
φ
IN
φ
φ
φ
Pulldown
Network
Out1
φ
Pulldown
Network
Out2
φ
Figure 6.15 Conventional DOMINO Dynamic Logic.
φ
Pulldown
Network
Pulldown
Network
Out3
φ
Out4
Chapter 6 Problem Set
8
23.
a. Complete the timing diagram for signals Out1, Out2, Out3 and Out4, when the IN signal
goes high before the rising edge of the clock φ. Assume that the clock period is 10 T time
units.
b. Suppose that there are no evaluate switches at the 3 latter stages. Assume that the clock φ
is initially in the precharge state (φ=0 with all nodes settled to the correct precharge
states), and the block enters the evaluate period (φ=1). Is there a problem during the evaluate period, or is there a benefit? Explain.
c. Assume that the clock φ is initially in the evaluate state (φ=1), and the block enters the precharge state (φ = 0). Is there a problem, or is there any benefit, if the last three evaluate
switches are removed? Explain.
[C, Spice, 4.3] Figure 6.16 shows a dynamic CMOS circuit in Domino logic. In determining
source and drain areas and perimeters, you may use the following approximations: AD = AS =
W × 0.625µm and PD = PS = W + 1.25µm. Assume 0.1 ns rise/fall times for all inputs,
including the clock. Furthermore, you may assume that all the inputs and their complements
are available, and that all inputs change during the precharge phase of the clock cycle.
a. What Boolean functions are implemented at outputs F and G? If A and B are interpreted as
two-bit binary words, A = A1A0 and B = B1B0, then what interpretation can be applied to
output G?
b. Which gate (1 or 2) has the highest potential for harmful charge sharing and why? What
sequence of inputs (spanning two clock cycles) results in the worst-case charge-sharing
scenario? Using SPICE, determine the extent to which charge sharing affects the circuit
for this worst case..
2.5 V
φ
2.5 V
2/0.25
B0
φ
1/0.25
1/0.25
A0
1/0.25
B0
2/0.25
φ
F
0.5/0.25
2.5 V
2/0.25
1/0.25
1/0.25
0.5/0.25
A1
2/0.25
A1
B1
2/0.25
B1
φ
GATE 1
2.5 V
G
CL
2/0.25
GATE 2
Figure 6.16 DOMINO logic circuit.
24.
[M, Spice, 4.3] In this problem you will consider methods for eliminating charge sharing in
the circuit of Figure 6.16. You will then determine the performance of the resulting circuit.
a. In problem 24 you determined which gate (1 or 2) suffers the most from charge sharing.
Add a single 2/0.25 PMOS precharge transistor (with its gate driven by the clock φ and its
source connected to VDD) to one of the nodes in that gate to maximally reduce the chargesharing effect. What effect (if any) will this addition have on the gate delay? Use SPICE to
demonstrate that the additional transistor has eliminated charge sharing for the previously
determined worst-case sequence of inputs.
b. For the new circuit (including additional precharge transistor), find the sequence of inputs
(spanning two clock cycles) that results in the worst-case delay through the circuit.
Digital Integrated Circuits - 2nd Ed
25.
9
Remember that precharging is another factor that limits the maximum clocking frequency
of the circuit, so your input sequence should address the worst-case precharging delay.
c. Using SPICE on the new circuit and applying the sequence of inputs found in part (b), find
the maximum clock frequency for correct operation of the circuit. Remember that the precharge cycle must be long enough to allow all precharged nodes to reach ~90% of their
final values before evaluation begins. Also, recall that the inputs (A, B and their complements) should not begin changing until the clock signal has reached 0 V (precharge
phase), and they should reach their final values before the circuit enters the evaluation
phase.
[C, None, 4.2–3] For this problem, refer to the layout of Figure 6.17.
a. Draw the schematic corresponding to the layout. Include transistor sizes.
b. What logic function does the circuit implement? To which logic family does the circuit
belong?
c. Does the circuit have any advantages over fully complementary CMOS?
d. Calculate the worst-case VOL and VOH.
e. Write the expresions for the area and perimeter of the drain and source for all of the FETs
in terms of λ . Assume that the capacitance of shared diffuusions divides evenly between
the sharing devices. Copy the layout into Magic, extract and simulate to find the worstcase tpHL time. For what input transition(s) does this occur? Name all of the parasitic
capacitances that you would need to know to calculate this delay by hand (you do not need
to perform the calculation).
Figure 6.17 Layout
of complex gate.
26.
27.
[E, None, 4.4] Derive the truth table, state transition graph, and output transition probabilities
for a three-input XOR gate with independent, identically distributed, uniform white-noise
inputs.
[C, None, 4.4] Figure 6.18 shows a two-input multiplexer. For this problem, assume independent, identically-distributed uniform white noise inputs.
Chapter 6 Problem Set
10
a. Does this schematic contain reconvergent fan-out? Explain your answer.
b. Find the exact signal (P1) and transition (P0 → 1) formulas for nodes X, Y, and Z for: (1) a
static, fully complementary CMOS implementation, and (2) a dynamic CMOS implementation.
X
A
S
C
Z
C
Y
B
28.
29.
C
Figure 6.18 Two-input multiplexer
[M, None, 4.4] Compute the switching power consumed by the multiplexer of Figure 6.18,
assuming that all significant capacitances have been lumped into the three capacitors shown
in the figure, where C = 0.3 pF. Assume that VDD = 2.5 V and independent, identically-distributed uniform white noise inputs, with events occuring at a frequency of 100 MHz. Perform
this calculation for the following:
a. A static, fully-complementary CMOS implementation
b. A dynamic CMOS implementation
Consider the circuit shown Figure 6.19.
a. What is the logic function implemented by this circuit? Assume that all devices (M1-M6)
are 0.5µm/0.25µm.
b. Let the drain current for each device (NMOS and PMOS) be 1µA for NMOS at VGS= VT
and PMOS at VSG= VT. What input vectors cause the worst case leakage power for each
output value? Explain (state all the vectors, but do not evaluate the leakage). Ignore DIBL.
c. Suppose the circuit is active for a fraction of time d and idle for (1-d). When the circuit is
active, the inputs arrive at 100 MHz and are uniformly distributed (Pr(A =1) = 0.5,
Pr(B=1) = 0.5, Pr(C=1) = 0.5) and independent. When the circuit is in the idle mode, the
inputs are fixed to one you chose in part (b). What is the duty cycle d for which the active
power is equal to the leakage power?
VDD = 2.5V
B
M4
C
M5
A
B
M1
VDD = 2.5V
A
M6
Out
CL = 50fF
M3
C
M2
Figure 6.19 CMOS
logic gate.
Digital Integrated Circuits - 2nd Ed
11
DESIGN PROJECT
Design, lay out, and simulate a CMOS four-input XOR gate in the standard 0.25 micron CMOS process. You can choose any logic circuit
style, and you are free to choose how many stages of logic to use: you
could use one large logic gate or a combination of smaller logic gates.
The supply voltage is set at 2.5 V! Your circuit must drive an external
20 fF load in addition to whatever internal parasitics are present in your
circuit.
The primary design objective is to minimize the propagation delay
of the worst-case transition for your circuit. The secondary objective is
to minimize the area of the layout. At the very worst, your design must
have a propagation delay of no more than 0.5 ns and occupy an area of
no more than 500 square microns, but the faster and smaller your circuit,
the better. Be aware that, when using dynamic logic, the precharge time
should be made part of the delay.
The design will be graded on the magnitude of A × tp2, the product
of the area of your design and the square of the delay for the worst-case
transition.
chapter7-ex.fm Page 1 Wednesday, October 29, 2003 11:52 PM
Chapter 7 Problem Set
1
Chapter 7
PROBLEMS
[M, None, 7.4] Figure 1 shows a practical implementation of a pulse register. Clock Clk is
ideal with 50% duty cycle.
1.
V DD
Q
X
Q
D
Clk d
Clk
Figure 0.1
Pulse register.
Data : VDD = 2.5V, tp,inv = 200ps, node capacitances are CClkd = 10fF, Cx = 10fF, both true and
complementary outputs node capacitances are 20fF.
a. Draw the waveforms at nodes Clk, Clkd, X and Q for two clock cycles, with D = 0 in one
cycle and D = 1 in the other.
b. What is the approximate value of setup and hold times for this circuit?
c. c)If the probability that D will change its logic value in one clock cycle is α, with equal
probability of being 0 or 1, what is the power consumption of this circuit? (exclude the
power consumption in the clock line) fclk = 100 MHz.
chapter7-ex.fm Page 2 Wednesday, October 29, 2003 11:52 PM
Chapter 7 Problem Set
2
2.
[M, None, 7.4] Figure 2 shows a register that attempts to statistically reduce power consumption using a data-transition look-ahead technique.
Q
CKI
D
DI
CKIB
CKIB
Data-Transition
Look-Ahead
Pulse
Generator
XNOR
CKIB
Clk
CKI
Figure 0.2 Pulse register.
3.
a. Briefly describe the operation of the circuit.
b. If all the NMOS transistors are of the same size, and all of the PMOS transistors are of the
same size, two times wider than the NMOS, roughly determine the input switching probability under which this flip-flop reduces power, compared to an equivalent flip-flop without data-transition look-ahead circuitry.
[E, None, 7.6] Shown in Figure 3 is a novel design of a Schmitt trigger. Determine the W/L
ratio of transistor M1 such that VM+ = 3VTn. VDD = 2.5V. The W/L ratios of other transistors are
shown in figure. You may ignore the body effect in this question. The other transistor parameters are as given in Chapter 3.
NMOS: VTn = 0.4V, kn’ = 115µA/V2, VDSAT = 0.6V, λ = 0, γ = 0V1/2
chapter7-ex.fm Page 3 Wednesday, October 29, 2003 11:52 PM
Digital Integrated Circuits - 2nd Ed
3
PMOS: VTp = -0.4V, kp’ = -30µA/V2, VDSAT = -1V, λ = 0, γ = -0V1/2
VDD
2.5
M4
M2
Vout
VDD
VX
1
Vin
10
M3
?
M1
Figure 0.3 Schmitt trigger.
4.
[M, None, 7.6] Consider the circuit in Figure 4. The inverter is ideal, with VM=VDD/2 and
infinite slope. The transistors have VT_=0.4V, kn’=120 µA/V2 and kp= 40 µA/V2. M1 has
(W/L)1=1. Ignore all other parasitic effects in the transistors.
VDD = 1.2V
M2
X
Vin
M1
Figure 0.4
Vout
M3
Schmitt trigger.
a. As VIN goes from 0 to VDD and back to 0 explain the sequence of events which makes this
circuit operate as a Schmitt Trigger.
b. Find the value of (W/L)2 such that when VIN increases from 0 to VDD the output will
switch at Vin = 0.8V.
c. Find the value of (W/L)3 such that when Vin decreases from VDD to 0 the output will
switch at Vin = 0.4V. If you don’t trust your value from b., you may use (W/L)2=5.
chapter7-ex.fm Page 4 Wednesday, October 29, 2003 11:52 PM
Chapter 7 Problem Set
4
5.
[M, None, 7.6] Figure 5 shows an astable multivibrator. Calculate and draw voltage waveforms at the capacitor VC and at the output Vout. What is the oscillation frequency of the multivibrator?
R1
D1
R2
D2
VC
V out
C
R3
R4
Figure 0.5 Astable multivibrator.
Assume that the amplifier is ideal, with symmetric supplies (Voutmax = VDD, Voutmin = -VSS)
R1 = 1kΩ, R2 = 3kΩ, R3 = R4 = 4kΩ, C = 1nF, VDD = -VSS == 5V, diode voltage VD = 0.6V
(ideal diode), Vout (t = 0-) = -VSS.
6. [E, None, 7.6] An oscillator is shown in Figure 6. Draw the signal waveforms for this circuit
at nodes X, Y, Z, A, and B. Determine the oscillation frequency. You may assume that the
delay of the inverters, the resistances of the MOS transistors, and all internal capacitors can be
ignored. The inverter switch point is set at 1.25V. Assume that nodes Y and Z are initially at
0V and 2.5V, respectively.
3.3V
I0 = 4.2µA
A
C0 = 1pF
X
2.5V
C1 = 1pF
B
I1 = 1.4µA
Figure 0.6
Oscillator.
Y
Z
chapter7-ex.fm Page 5 Wednesday, October 29, 2003 11:52 PM
Digital Integrated Circuits - 2nd Ed
7.
5
[E, None, 7.6] Consider the oscillator in Figure 7. Assume that the “n” switches turn “on” for
voltages above VDD/2, and the “p” switches turn “on” for voltages below VDD/2. Assume that
the current sources stop when the node voltage charges to either VDD or ground.
V DD
V DD
50µA
p
50µA
p
X
20fF
n
8.
50µA
p
Y
20fF
n
50µA
Figure 0.7
V DD
50µA
Z
20fF
n
50µA
Oscillator.
a. Find the oscillation period for VDD = 3V.
b. Draw the waveforms at nodes X, Y, and Z for two periods.
c. Find the oscillation period.
[M, None, 7.6] The circuit in Figure 8 operates at a supply voltage of 3V and uses two
Schmitt triggers with the following threshold voltages: VM+ = 2V, VM- = 1V.
X
Y
R
A
Figure 0.8
C
A circuit composed of Schmitt triggers.
a. Identify whether the circuit is monostable, bistable, or astable?
b. Draw the waveforms at nodes X, Y, and A. Mark all important voltage levels.
c. Calculate the key timing parameter for this circuit (propagation delay for bistable, pulse
width for monostable, and time period for astable) in terms of R and C. You can assume
that gate delays are negligible compared to the delay of the RC network.
1
Chapter 10 Problem Set
Chapter 10
PROBLEMS
Logic
Logic
Logic
Logic
tθ
Logic
Register
Mux
Logic
Logic
Logic
[C, None, 9.2] For the circuit in Figure 0.1, assume a unit delay through the Register and
Logic blocks (i.e., tR = tL = 1). Assume that the registers, which are positive edge-triggered,
have a set-up time tS of 1. The delay through the multiplexer tM equals 2 tR.
a. Determine the minimum clock period. Disregard clock skew.
b. Repeat part a, factoring in a nonzero clock skew: δ = t′θ – tθ = 1.
c. Repeat part a, factoring in a non-zero clock skew: δ = t′θ – tθ = 4.
d. Derive the maximum positive clock skew that can be tolerated before the circuit fails.
e. Derive the maximum negative clock skew that can be tolerated before the circuit fails.
Register
1.
t′θ
Θ
Figure 0.1
2.
Sequential circuit.
This problem examines sources of skew and jitter.
a. A balanced clock distribution scheme is shown in Figure 0.2. For each source of variation,
identify if it contributes to skew or jitter. Circle your answer in Table 0.1
4 Power Supply Noise
3 Interconnect
Devices 2
5 Data Dependent Load
6 Static Temperature Gradient
1 Clock Generation
Figure 0.2
Sources of Skew and Jitter in Clock Distribution.
2
Chapter 10 Problem Set
1) Uncertainty in the clock generation circuit
Skew
Jitter
2) Process variation in devices
Skew
Jitter
3) Interconnect variation
Skew
Jitter
4) Power Supply Noise
Skew
Jitter
5) Data Dependent Load Capacitance
Skew
Jitter
6) Static Temperature Gradient
Skew
Jitter
Table 0.1 Sources os Skew and Jitter
b. Consider a Gated Clock implementation where the clock to various logical modules can be
individually turned off as shown in Figure 0.3. (i.e., Enable1,..., EnableN can take on difVDD
Enable
Input
Clock
Driver
Enable1
Clk
VDD
Enable
Clk
Gated
Clock
Enable
Enable2
Clk
Gated
Clock
Clk
Clk
Enable
EnableN
Fine-grain Clock Gating
Gating Approach A
Gating Approach B
Figure 0.3 Jitter in clock gating
3.
ferent values on a cycle by cycle basis). Which approach (A or B) results in lower jitter at
the output of the input clock driver? (hint: consider gate capacitance) Explain.
Figure 0.4 shows a latch based pipeline with two combinational logic units.
I
D Q
CLK
a
CL1 b
80ns
c
D Q
CL2 d
30ns
CLK
Figure 0.4 Latch Based Pipeline
D Q
CLK
e
Digital Integrated Circuits - 2nd Ed
3
Recall that the timing diagram of a combinational logic block and a latch can be drawn
as follows, where the shaded region represents that the data is not ready yet.
IN
CL
IN
OUT
D Q
OUT
CLK
IN
IN
OUT
CLK
tpd
OUT
Figure 0.5 Timing diagrams of combinational logic and latch
Assume that the contamination delay tcd of the combinational logic block is zero, and the tclk-q
of the latch is zero too.
a. Assume the following timing for the input I. Draw the timing diagram for the signals a, b,
c, d and e. Include the clock in your drawing.
CLK
I
T=100ns
Figure 0.6 Input timing
b. State the deadline for the computation of the signal b and d, i.e. when is the latest time
they can be computed, relative to the clock edges. In your diagram for (a), label with a “<
>” the “slack time” that the signals b and d are ready before the latest time they must be
ready.
c. Hence deduce how much the clock period can be reduced for this shortened pipeline.
Draw the modified timing diagram for the signals a, b, c, d, and e. Include the clock in
your drawing.
φ
Reg
Reg
Consider the circuit shown in Figure 0.7.
Reg
4.
φ
φ
Figure 0.7 Sequential Circuit
a. Use SPICE to measure tmax and tmin. Use a minimum-size NAND gate and inverter.
Assume no skew and a zero rise/fall time. For the registers, use the following:
• A TSPC Register.
• A C2MOS Register.
b. Introduce clock skew, both positive and negative. How much skew can the circuit tolerate
and still function correctly?
c. Introduce finite rise and fall time to the clocks. Show what can occur and describe why.
4
Chapter 10 Problem Set
5.
Consider the following latch based pipeline circuit shown in Figure 0.8.
Assume that the input, IN, is valid (i.e., set up) 2ns before the falling edge of CLK and
is held till the falling edge of CLK (there is no guarantee on the value of IN at other times).
Determine the maximum positive and negative skew on CLK’ for correct functionality.
Combinational Logic
Input
D
Propagation Delay: 7ns
Contamination Delay: 1ns
Q
D Q
Output
Latch Parameters:
tD-Q = 1ns (D to Q delay)
thold=0
tsu=1ns
Wire Delay
CLK
CLK’
T= 20ns
tin,su=2ns
CLK
IN
Figure 0.8 Latch based pipeline
6.
For the L1-L2 latch based system from Figure 0.9, with two overlapping clocks derive all the
necessary constraints for proper operation of the logic. The latches have setup times TSU1 and
TSU2, data-to-output delays TD-Q1 and TD-Q2, clock-to-output delays TClk-Q1 and TClk-Q2, and hold
times TH1 and TH2, respectively. Relevant clock parameters are also illustrated in Figure 0.9.
The constraints should relate the logic delays, clock period, overlap time TOV, pulse widths
PW1 and PW2 to latch parameters and skews.
φ1
φ2
L1
Latch
L2
Latch
Tskr1
PW1
φ1
TOV
Tskl1
PW2
φ2
Logic
Tskl2
Tskr2
Figure 0.9 Timing constraints
7.
For the self-timed circuit shown in Figure 0.10, make the following assumptions. The propagation through the NAND gate can be 5 nsec, 10 nsec, or 20 nsec with equal probability. The
logic in the succeeding stages is such that the second stage is always ready for data from the
first.
a. Calculate the average propagation delay with ths = 6 nsec.
b. Calculate the average propagation delay with ths =12 nsec.
Digital Integrated Circuits - 2nd Ed
5
c. If the handshaking circuitry is replaced by a synchronous clock, what is the smallest possible clock frequency?
Req
HS
8.
9.
2 INPUT
NAND
HS
Ack
LOGIC
Figure 0.10
Self-timed circuit.
Lisa and Marcus Allen have a luxurious symphony hall date. After pulling out of their driveway, they pull up to a four-way stop sign. They pulled up to the sign at the same time as a car
on the cross-street. The other car, being on the right, had the right-of-way and proceeded first.
On the way they also have to stop at traffic signals. There is so much traffic on the freeway,
the metering lights are on. Metering lights regulate the flow of merging traffic by allowing
only one lane of traffic to proceed at a time. With all the traffic, they arrive late for the symphony and miss the beginning. The usher does not allow them to enter until after the first
movement.
On this trip, Lisa and Marcus proceeded through both synchronizers and arbiters. Please
list all and explain your answer.
Design a self-timed FIFO. It should be six stages deep and have a two phase handshakin with
the outside world. The black-box view of the FIFO is given in Figure 0.11.
In
Req
Ack
10.
Done
Register
Register
Start
Out
Req
Ack
Figure 0.11 Overall
structure of FIFO.
System Design issues in self-timed logic
One of the benefits of using self-timed logic is that it delivers average-case of performance rather than the worst-case performance that must be assumed when designing synchronous circuits. In some applications where the average and worst cases differ significantly you
can have significant improvements in terms of performance. Here we consider the case of ripple carry addition. In a synchronous design the ripple carry adder is assumed to have a worst
case performance which means a carry-propagation chain of length N for an N-bit adder.
However, as we will prove during the course of this problem the average length of the carrypropagation chain assuming uniformly distributed input values is in fact O(log N)!
a. Given that pn (v) = Pr(carry-chain of an n-bit addition is ≥ v bits), what is the probability
that the carry chain is of length k for an n-bit addition?
b. Given your answer to part (a), what is the average length of the carry chain (i.e., an)? Simplify your answer as much as possible.
Now pn(v) can be decomposed into two mutually-exclusive events, A and B. Where A
represents that a carry chain of length ≥ v occurs in the first n-1 bits, and B represents that a
carry chain of length v ends on the nth bit.
c. Derive an expression for Pr(A).
6
Chapter 10 Problem Set
d. Derive an expression for Pr(B). (HINT: a carry bit i is propagated only if ai ≠ bi, and a
carry chain begins only if ai = bi = 1).
e. Combine your results from (c) and (d) to derive an expression for pn(v) - pn-1(v) and then
bound this result from above to yield an expression in terms of only the length of the carry
chain (i.e., v).
f. Using what you’ve shown thus far, derive an upper bound for the expression:
n
∑ (p (v) – p
i
i – 1(v))
i=v
11.
Use this result, coupled with the fact that pn(v) is a probability (i.e., it’s bounded from
above by 1), to determine a two-part upper bound for pn(v).
g. (The magic step!) Bound n by a clever choice of k such that 2k ≤ n ≤ 2k+1 and exploit the
fact that log2 x is concave down on (0, ∞) to ultimately derive that an ≤ log2 n, which concludes your proof!
h. Theoretically speaking, how much faster would a self-timed 64-bit ripple carry adder be
than its synchronous counterpart? (You may assume that the overhead costs of using selftimed logic are negligible).
Figure 0.12 shows a simple synchronizer. Assume that the asynchronous input switches at a
rate of approximately 10 MHz and that tr = 2 nsec, fφ = 50 MHz, VIH − VIL=0.5 V, and VDD =
2.5 V.
a. If all NMOS devices are minimum-size, find (W/L)p required to achieve VMS = 1.25 V.
Verify with SPICE.
b. Use SPICE to find τ for the resulting circuit.
c. What waiting time T is required to achieve a MTF of 10 years?
d. Is it possible to achieve an MTF of 1000 years (where T > Tφ)? If so, how?
Vout
Vin
30 fF
30 fF
φ
Figure 0.12 Simple synchronizer
Digital Integrated Circuits - 2nd Ed
12.
7
Explain how the phase-frequency comparator shown in Figure 0.13 works.
R
UP
DN
V
Figure 0.13 Phase-frequency comparator
13.
The heart of any static latch is the cross-coupled structure shown in Figure 0.14 (part a).
a. Assuming identical inverters with Wp/Wn =kn’/kp’, what is the metastable point of this
circuit? Give an expression for the time trajectory of VQ, assuming a small initial Vd0 centered around the metastable point of the circuit, VM.
Q
B
Q
A
a) Latch
Q
Metastability
Detector
Latch
M⋅D
b) Metastability Detector
M
τ
Q
D
c) Synchronizer
M⋅D
Figure 0.14
Simple synchronizer
b. The circuit in part b has been proposed to detect metastability. How does it work? How
would you generate a signal M that is high when the latch is metastable?
8
Chapter 10 Problem Set
14.
c. Consider the circuit of part c. This circuit was designed in an attempt to defeat metastability in a synchronizer. Explain how the circuit works? What ís the function of the delay element?
An adjustable duty-cycle clock generator is shown in Figure 0.15. Assume the delay through
the delay element matches the delay of the multiplexer.
a. Describe the operation of this circuit
b. What is the range of duty-cycles that can be achieved with this circuit.
c. Using an inverter and an additional multiplexer, show how to make this circuit cover the
full range of duty cycles.
Multiplexer
Delay
CLOCK
15.
1
Figure 0.15
generator.
Clock duty-cycle
The circuit style shown in Figure 0.17.a has been proposed by Acosta et. al. as a new selftimed logic style. This structure is known as a Switched Output Differential Structure1.
a. Describe the operation of the SODS gate in terms of its behavior during the pre-charge
phase, and how a valid completion signal can be generated from its outputs.
b. What are the advantages of using this logic style in comparison to the DCVSL logic style
given in the notes?
c. What are the disadvantages of using this style in comparison to DCVSL?
d. Figure 0.16.b shows a 2-input AND gate implemented using a SODS style. Simulate the
given circuit using Hspice. Do you notice any problems? Explain the cause of any problems that you may observe and propose a fix. Re-simulate your corrected circuit and verify that you have in fact fixed the problem(s).
A.J. Acosta, M. Valencia, M.J. Bellido, J.L. Huertas, “SODS: A New CMOS Differential-type
Structure,” IEEE Journal of Solid State Circuits, vol. 30, no. 7, July 1995, pp. 835-838
Digital Integrated Circuits - 2nd Ed
Vdd
9
Vdd = 2.5V
Vdd
Vdd
Vdd
24/2
24/2
Φ
Φ
3/2
Φ
inputs
out
out
out
out
Φ
PDN
PDN
Φ
3/2
3/2
Φ
B
4/2
8/2
B
8/2
A
A
Figure 0.17 a - SODS Logic Style
16.
4/2
Figure 0.16 b - 2-input And Gate in SODS Style
Voltage Control Ring Oscillator.
In this problem, we will explore a voltage controlled-oscillator that is based upon John
G. Maneatis’ paper in Nov. 1996, entitled “Low Jitter Process-Independent DLL and PLL
Based on Self-Biased Techniques,” appeared in the Journal of Solid-State Circuits. We will
focus on a critical component of the PLL design: the voltage-controlled ring oscillator. Figure
0.17 shows the block diagram of a voltage controlled ring oscillator:
Vctl
Vin+
Bias
Generator
Vctlp
Vctln
Voutdelay
Vin-
Vctlp
delay
delay
delay
Vout+
Vctln
Figure 0.17 Voltage Controlled Ring Oscillator
The control voltage, Vctl, is sent to a bias generator that generates two voltages used to
properly bias each delay cell equally, so that equal delay (assuming no process variations)
appear across each delay cell. The delay cells are simple, “low-gain” fully differential input
and output operational amplifiers that are connected in such a way that oscillations will occur
at any one of the outputs with a frequency of 1/(4*delay). Each delay is modeled as an RC
time constant; C comes from parasitic capacitances at the output nodes of the delay element,
10
Chapter 10 Problem Set
and R comes from the variable resistor that is the load for the delay cell. Below is a circuit
schematic of a typical delay cell.
24/2
24/2
24/2
24/2
Vctlp
Vout-
Vout+
Vin+
36/2
36/2
Vin-
48/2
Vctln
Figure 0.18 One delay Cell
As mentioned before, the value of R is set by a variable resistor. How can one make a
variable resistor? The object in the delay cell that is surrounded by a dotted line is called a
“symmetric load,” and provides the answer to a voltage-controlled variable resistor. R should
be linear so that the differential structure cancels power supply noise. We will begin our analysis with the symmetric load.
a. In Hspice, input the circuit below and plot Vres on the X axis and Ires on the Y axis, for
the following values of Vctlp: 0.5, 0.75, 1.0, 1.25, 1.5, 1.75, and 2.0 volts, by varying
Vtest from Vctlp to Vdd, all on the same graph. For each curve, plot Vres from 0 volts to
Vdd-Vctlp. When specifying the Hspice file, be sure to estimate area and perimeter of
drains/sources.
+
Vres
24/2
-
24/2
Vctlp
Ires
+
-
Vtest
Figure 0.19 :Symmetric Load Test Circuit
After you have plotted the data and printed it out, use a straight edge to connect the end
points for each curve. What do you notice about intersection points between the line you drew
over each curve, and the curves themselves? Describe any symmetries you see.
b. For each Vctlp curve that you obtained in a), extract the points of symmetries (Vres, Ires),
and find the slope of the line around these points of symmetry. These are the effective
resistances of the resistors. Also, for each Vctl curve, state the maximum amplitude the
output swing can be, without running into asymmetries. Put all of this data in an worksheet
format.
c. Using the estimations you made for area and perimeter of drain ad source that you put in
your Hspice file, calculate the effective capacitance. (Just multiply area and perimeter by
CJ and CJSW from the spice deck). Since we are placing these delay elements in a cas-
Digital Integrated Circuits - 2nd Ed
11
caded fashion, remember to INCLUDE THE GATE CAPACITANCE of the following
stage. Each delay element is identical to one another. Now, calculate the delay in each
cell, according to each setting of Vctlp that you found in a): delay=0.69*R*C. Then, write
a general equation, in terms of R and C, for the frequency value that will appear at each
delay output. Why is it necessary to cross the feedback lines for the ring oscillator in the
first figure? Finally, draw a timing/transient analysis of each output node of the delay
lines. How many phases of the base frequency are there?
d. Now, we will look at the bias generator. The circuit for the bias generator is as follows:
24/2
24/2
24/2
24/2
Vctl
Vctlp
72/2
72/2
+
_
A
48/2
48/2
Vctln
Figure 0.20 :Bias Generator
Implement this circuit in Hspice, and use the ideal voltage controlled voltage source
for your amplifier. Use a value of 20 for A. This circuit automatically sets the Vctln and Vctlp
voltages to the buffer delays to set the DC operating points of the delay cells such that the
symmetric load is swinging reflected around its point of symmetry for a given Vctl voltage.
Also, it is important to note that Vctl is the same as Vctlp. It must go through this business to
obtain Vctln (which sets the bias current to the correct value, which sets the DC operating
point of the buffer). Do a transient run in Hspice to verify that Vctlp is indeed very close to
Vctl over a range of inputs for Vctl. Show a Spice transient simulation that goes for 1uS, and
switches Vctl in a pwl waveform across a range of inputs between 0.5V and 2.0V. For extra
points, explain how this circuit works.
e. Now, hook up the bias generator you just built with 4 delay cells, as shown in the first figure. For each control voltageVctlp from part c), verify your hand calculations with spice
simulations. Show a spreadsheet of obtained frequencies vs. hand-calculation predictions,
and in a separate column, calculate % error. Give a brief analysis of what you see. Print
out all of the phases (4) of the clock, for a Vctl value of your choice.
second-chapter11-ex.fm Page 1 Friday, October 3, 2003 9:48 PM
Chapter 11 Problem Set
1
Chapter 11
PROBLEMS
1.
2.
3.
[E, None, 11.6] For this problem you are given a cell library consisting of full adders and twoinput Boolean logic gates (i.e. AND, OR, INVERT, etc.).
a. Design an N-bit two's complement subtracter using a minimal number of Boolean logic
gates. The result of this process should be a diagram in the spirit of Figure 11.5 . Specify
the value of any required additional signals (e.g., Cin ).
b. Express the delay of your design as a function of N, tcarry , tsum , and the Boolean gate delays
(tand , tor , tinv, etc.).
[M, None, 11.6] A magnitude comparator for unsigned numbers can be constructed using full
adders and Boolean logic gates as building blocks. For this problem you are given a cell
library consisting of full adders and arbitrary fan-in logic gates (i.e., AND, OR, INVERTER,
etc.).
a. Design an N-bit magnitude comparator with outputs A ≥ B and A = B using a minimal
number of Boolean logic gates. The result of this process should be a diagram in the spirit
of Figure 11.5. Specify the value of any required control signals (e.g., Cin ).
b. Express the delay of your design in computing the two outputs as a function of N, tcarry ,
tsum, and the Boolean gate delays (t and, tor , tinv, etc.).3.
[E, None, 11.6] Show how the arithmetic module in Figure 0.1 can be used as a comparator.
Derive an expression for its propagation delay as a function of the number of bits.
ai
ai
bj
bj
cj
cj+ 1
dj
d j+1
4.
5.
c0 c1
c1 c2
c2 c3
c3 c4
d0 d1
d1 d2
d2 d3
d3 d4
a0 b0
a1 b1
a2 b2
a3 b3
Figure 0.1
Arithmetic module.
[E, None, 11.6] The circuit of Figure 11.2 implements a 1-bit datapath function in dynamic
(precharge/evaluate) logic.
a. Write down the Boolean expressions for outputs F and G. On which clock phases are outputs F and G valid?
b. To what datapath function could this unit be most directly applied (e.g., addition, subtraction, comparison, shifting)?
[M, None, 11.3] Consider the dynamic logic circuit of Figure 0.2 .
a. What is the purpose of transistor M1? Is there another way to achieve the same effect, but
with reducing capacitive loading on the clock Φ?
second-chapter11-ex.fm Page 2 Friday, October 3, 2003 9:48 PM
Chapter 11 Problem Set
2
A
B
A
B
A
C in
A
M1
B
C in
C in
B
G
Φ
Φ
Figure 0.2
F
6.
Datapath module bit-slice.
b. How can the evaluation phase of F be sped up by rearranging transistors? No transistors
should be added, deleted, or resized.
c. Can the evaluation of G be sped up in the same manner? Why or why not?
[M, SPICE, 11.3] The adder circuit of Figure 0.3 makes extensive use of the transmission
gate XOR. V DD = 2.5 V.
a. Explain how this gate operates. Derive the logic expression for the various circuit nodes.
Why is this a good adder circuit?
b. Derive a first-order approximation of the capacitance on the Co-node in equivalent gatecapacitances. Assume that gate and diffusion capacitances are approximately identical.
Compare your result with the circuit of Figure 11-6 .
c. Assume that all transistors with the exception of those on the carry path are minimumsize. Use 4/0.25 NMOS and 8/0.25 PMOS devices on the carry-path. Using SPICE simulation, derive a value for all important delays (input-to-carry, carry-to-carry, carry-tosum).
B
V DD
B
B
A
P
V DD
V DD
A
P
P
P
Ci
B
P
Signal setup
V DD
Co
P
P
Ci
S
A
Ci
P
P
Figure 0.3
Sum generation
Quasi-clocked adder circuit.
Carry generation
second-chapter11-ex.fm Page 3 Friday, October 3, 2003 9:48 PM
Digital Integrated Circuits - 2nd Ed
7.
8.
3
[M, None, 11.3] The dynamic implementation of the 4-bit carry-lookahead circuitry from Fig.
11-21 can significantly reduce the required transistor count.
a. Design a domino-logic implementation of Eq. 11.17 . Compare the transistor counts of the
two implementations.
b. What is the worst-case propagation delay path through this new circuit?
c. Are there any charge-sharing problems associated with your design? If so, modify your
design to alleviate these effects.
[C, None, 11.3] Figure 0.4 shows a popular adder structure called the conditional-sum adder.
Figure 0.4.a shows a four-bit instance of the adder, while 0.4.b gives the schematics of the
basic adder cell. Notice that only pass-transistors are used in this implementation.
a. Derive Boolean descriptions for the four outputs of the one-bit conditional adder cell.
b. Based on the results of describe how the schematic of 0.4.a results in an addition.
c. Derive an expression for the propagation delay of the adder as a function of the number of
bits N. You may assume that a switch has a constant resistance Ron when active and that
each switch is identical in size.
B3
A3
B2
A2
B1
A1
B0
A0
Conditional
Cell
Conditional
Cell
Conditional
Cell
Conditional
Cell
C 1 C 0 S1 S0
C 1 C 0 S1 S0
C 1 C0 S 1 S 0
C 1 C0 S 1 S 0
C out
S3
S2
S1
S0
(a) Four-bit conditional-sum adder
A
A
B
B
A
B
A
A
B
A
B
S0
A
A
B
A
A
B
A
S1
A
A
C0
C1
A
A
B
A
(b) Conditional adder cell
Figure 0.4 Conditional-sum adder.
9.
[M, None, 11.3] Consider replacing all of the NMOS evaluate transistors in a dynamic
Manchester carry chain with a single common pull-down as shown in Fgure 0.5.a. Assume
that each NMOS transistor has (W/L)N = 0.5/0.25 and each PMOS has (W/L)P = 0.75/0.25.
Further assume that parasitic capacitances can be modeled by a 10 fF capacitor on each of the
second-chapter11-ex.fm Page 4 Friday, October 3, 2003 9:48 PM
Chapter 11 Problem Set
4
internal nodes: A, B, C, D, E, and F. Assume all transistors can be modeled as linear resistors
with an on-resistance, Ron = 5 kΩ.
a. Does this variation perform the same function as the original Manchester carry chain?
Explain why or why not.
b. Assuming that all inputs are allowed only a single zero-to-one transition during evaluation, will this design involve charge-sharing difficulties? Justify your answer.
c. Complete the waveforms in Figure 0.5b for P0 = P 1 = P2 = P3 = 2.5 V and G0 = G1 = G2 =
G3 = 0 V. Compute and indicate tpHL values for nodes A, E, and F. Compute and indicate
when the 90% precharge levels are obtained.
φ
V DD
1
φ
P0
P1
A
C in
B
G0
P2
C
G1
P3
D
G2
F
φ
C in
E
G3
4
5
8
t(nsec)
A
E
F
(a) Circuit schematic
Figure 0.5
(b) Partial waveforms
Alternative dynamic Manchester carry-chain adder.
10.
11.
12.
[M, None, 11.3] Consider the two implementations of Manchester carry gates in Figure 11-8.
a. Compare the delay per segment of the two implementations
b. Compare the layout complexities of the two gates using stick diagrams.
c. In the precharged Manchester carry chain using the gate from b. find the probability that
the carry signal is propagated from the 15th to the 16th bit of a 32-bit adder, assuming random inputs.
[C, None, 11.3] Consider the Radix-4 and Radix-2 Kogge-Stone adders from Figures 11-22
and 11-27 extended to 64-bits. All gates are implemented in domino and all gates in a stage
have the same size. The adders have an overall fanout (electrical effort) of 6.
a. Using logical effort, identify the critical path.
b. Size the gates for minimum delay (hint: don't forget to factor in branching). Which adder
is faster?
c. Let's now consider sparse versions of each of the above trees. In a tree with a sparseness of
2, only every other carry is computed and it is used to select 2 sums. Similarly, a tree with
a sparseness of 4 computes every fourth carry - and that carry signal is used to select 4
sums. Repeat a. and b. for Radix-2 and Radix-4 trees with sparseness of 2 and 4 and compare their speed. Which adder is fastest?
d. Compare the switching power of all adders analyzed in this problem.
[C, None, 11.3] In this problem we will analyze a carry-lookahead adder proposed by H. Ling
more than 20 years ago, but still among the fastest adders available. In a conventional adder,
in order to add two numbers
A = an−12n−1 + an−22n−2 + .... + a020
B = bn−12n−1 + bn−22n−2 + .... + b020
we first compute the local carry generate and propagate terms:
second-chapter11-ex.fm Page 5 Friday, October 3, 2003 9:48 PM
Digital Integrated Circuits - 2nd Ed
13.
14.
15.
16.
17.
5
gi = aibi
pi = ai + bi
then, with a ripple or a tree circuit we form the global carry-out terms resulting from the
recurrence relation:
Gi = gi + piGi−1
Finally, we form the sum of A and B using local expressions:
S i = pi ⊕ Gi – 1
In the conventional adder, the terms Gi have, as described, a physical significance. However,
an arbitrary function could be propagated, as long as sum terms could be derived. Ling's
approach is to replace Gi with:
Hi = Gi + Gi−1
i.e. Hi is true if "something happens at bit i" - there is a carry out or a carry in. Hi is so-called
"Ling's pseudo-carry".
a. Show that:
Hi = gi + ti−1Hi−1
where pi = ai + bi (it was Ling’s idea to change the notation).
b. Find a formula for computing the sum out of the operands and Ling's pseudo-carry.
c. Unroll the recursions for Gi and Hi for i = 3. You should get the expressions fpr G3 and H3
as a function of the bits of input operands. Simplify the expressions as much as possible.
d. Implement the two functions using n-type dynamic gates. Draw the two gates and size the
transistors. Which one helps us build a faster adder? Explain your answer.
[M, None, 11.4] An array multiplier consists of rows of adders, each producing partial sums
that are subsequently fed to the next adder row. In this problem, we consider the effects of
pipelining such a multiplier by inserting registers between the adder rows.
a. Redraw Figure 11-31 by inserting word-level pipeline registers as required to achieve
maximal benefit to throughput for the 4x4 multiplier. Hint: you must use additional registers to keep the input bits synchronized to the appropriate partial sums.
b. Repeat for a carry-save, as opposed to ripple-carry, architecture.
c. For each of the two multiplier architectures, compare the critical path, throughput, and
latency of the pipelined and nonpipelined versions.
d. Which architecture is better suited to pipelining, and how does the choice of a vectormerging adder affect this decision?
[M, None, 11.4] Estimate the delay of a 16x16 Wallace tree multiplier with the final adder
implemented using a Radix-4 tree. One FA has a delay of tp , a HA 2/3*tp and a CLA stage
½*tp .
[E, None, 11.5] The layout of shifters is dominated by the number of wires running through a
cell. For both the barrel shifter and the logarithmic shifter, estimate the width of a shifter cell
as a function of the maximum shift-width M and the metal pitch p.
[E, None, 11.7] Consider the circuit from Figure 0.7 . Modules A and B have a delay of 10 ns
and 32 ns at 2.5V, and switch 15 pF and 56 pF respectively. The register has a delay of 2 ns
and switches 0.1 pF. Adding a pipeline register allows for reduction of the supply voltage
while maintaining throughput. How much power can be saved this way? Delay with respect
to V DD can be approximated from Figure 11-57.
[E, None, 11.7] Repeat Problem 16, using parallelism instead of pipelining. Assume that a 2to-1 multiplexer has a delay of 4 ns at 2.5 V and switches 0.3 pF. Try parallelism levels of 2
and by 4. Which one is preferred?
second-chapter11-ex.fm Page 6 Friday, October 3, 2003 9:48 PM
Chapter 11 Problem Set
A
B
Register
In
Register
6
Out
Figure 0.6
Pipelined datapath.
DESIGN PROBLEM
Using the 0.25 µm CMOS technology, design a static 32-bit adder, with the following constraints:
1. input capacitance on each bit is limited to not more than 50fF.
2. each bit is loaded with 100fF.
Use a carry lookahead tree of your choice for implementation. The goal is to
achieve the shortest propagation delay.
Determine the logic design of the adder and W and L of all transistors.
Initially size the design using the method of logical effort. Estimate the capacitance of carry signal wires based on the floorplan. Verify and optimize the
design using SPICE. Compute also the energy consumed per transition. If you
have a layout editor available, perform the physical design, extract the real circuit parameters, and compare the simulated results with the ones obtained earlier. For implementation use the 144λ.bit-slice pitch, that corresponds to 36
metal-1 tracks. Use metal 1 for cell-level power distrbution and intra-cell routing, metal-2 for short interconnect and metal-3 and metal-4 for long carries.
Chapter 12
PROBLEMS
1.
2.
[E, SPICE, 12.2.1] Use SPICE to compute the access time of the 512 ⋅ 512 NOR ROM of Example
12.4. Use a simplified model (i.e., do not include all the transistors but model their impact on word and
bit lines). Compare the obtained results (row, column, and overall delay) with the results of the hand
analysis.
[E, None, 12.2.3] For a memory containing a 4096 word ⋅ 2048 bit array of SRAM cells with a
differential bit-line architecture, assume that the dynamic power consumption is dominated by charging
and discharging the bit lines. Assume further that the cells are tiled at a vertical pitch of 5
µm and a
horizontal pitch of 3 µm. Also assume that each cell adds a load of 3 fF to BL and BL’. Bit lines are in
metal1 and are 0.6 µm wide.
a.
Compute the capacitance loading each bit line. Break it down into contributions from wiring and
from memory cells.
b.
If the bit lines are precharged to 1.25 V and are allowed to develop a maximum differential voltage
of 1 V (symmetric around the precharge voltage) during a read operation, what is the power
consumption by the memory while reading at an access rate of 5 MHz.
3. [E, None, 12.2.3] Using the result of Eq. (12.3) and the device parameters of Table 3-2, construct a plot
of ∆V/VTn vs. VDD for an SRAM with a cell ratio of 1. Discuss the effect of supply voltage scaling on
read upset malfunction.
4. [M, None, 12.2.3] Consider the six-transistor NMOS static memory cell of Figure 12.85 . You may
ignore the body effect for this problem (γ = 0). Use (W/L)2 = 1.2/24 and (W/L)3 = 2.4/1.2. The threshold
voltage VTO of the depletion transistors equals –2 V. Assume Vdsat > Vdd (long channel device).
a.
Assume first that node Q is in the 1 state and node Q is 0. In order to write a 0 to node Q, bit line
BL is lowered to 0.9 V. Determine the minimal size of transistor M1 so that the cell just flips when
this voltage is reached. Assume that the switching threshold VM of the NMOS inverter equals 0.92
V.
b.
Assume now that (W/L)1 = 2.4/1.2. Determine the maximal precharge voltage on bit line BL so that
the cell does not flip during a read operation.
c.
Finally, suppose that the bit line has been precharged to 2 V and that the sense amplifier can detect
a voltage swing of 0.5 V. Determine how long the read operation would take, given that the bit-line
capacitance is 2 pF and the delay of the sense amp itself may be ignored. You may ignore the
current through the depletion load M2 for this part of the problem.
5.
6.
[E, None, 12.2.3] Draw the transistor diagram of a two-port SRAM cell. A two-port memory can read or
write two independent addresses simultaneously. Discuss qualitatively how this effects the transistor
sizing in the cell.
[M, None, 12.2.3] A two-transistor memory cell is shown in Figure 12.87. It uses two identical
transistors (M1 and M2) with W/L = 1.8/1.2. Separate lines are provided for the read select (RS) and write
select (WS), which both switch between 0 and 3 V. You may ignore body effect (γ = 0), channel-length
modulation (λ = 0), and short-channel effects (Vdsat > Vdd) throughout this problem. Use kn’ =
19.6uA/V2, Vtn = 0.743V, kp’ = 5.4uA/V2, Vtp = -0.739V.
a.
b.
c.
d.
Explain the operation of the memory. Draw waveforms for WB, RB, WS, and RS for both reads and
writes.
Determine the maximum possible current flowing into the cell during a read operation. State clearly
your assumptions and simplifications.
Determine the size (W/L) of transistor M3 so that the voltage on the bit line RB never drops below
2.5 V during a read operation.
Compute the time it takes to achieve a 0.5 V voltage drop on the bit line during a read operation.
Assume that Cc = 50 fF and Cb = 2 pF.
7.
[C, None, 12.2.3] Figure 12.88 shows a variant of the 1T-DRAM cell.
a.
Fill in the timing diagrams for nodes BL and Y when writing a 0 and a 1 into the cell. For WL and
PL, use the timing waveforms shown in the figure. Denote the voltage levels in terms of VDD and VT
(ignore body effect). Ignore transient effects.
b.
Describe briefly why this is an attractive approach.
c.
Assume that the bit-line capacitance equals 75 fF. The transistor threshold equals 0.4 V (ignore
body effect). The supply voltage equals 3 V and the bit line is pre(dis)charged to 0 V. Derive the
symbolic equations needed to the derive the bit line voltages after reading a 0 and a 1. Ignore
transient effects.
d.
Using the results from 10c, derive the minimum cell capacitance so that the voltage difference on
the bit line between reading a 0 and a 1 is larger than 150 mV.
8.
[M, None, 12.3.2] Figure 12.89 shows a DRAM with a divided bit line. Each side of the differential
sense amplifier connects to 256 DRAM cells and 1 dummy cell. The input capacitance of the sense amp
is 8 fF at each input. The BL and BL lines are in metal for which the resistive and capacitive
contributions can be neglected. The lumped junction capacitance of each cell is 0.8 fF. Ignore body
effect.
a.
Compute the effective capacitance on each bit line, Cbit.
b.
Draw the timing diagrams corresponding to reading a 0 and a 1 from cell 1. Draw the waveforms
for φp, φr, φd, φr, φd, BL and BL. Assume the sense amplifier refreshes values after reading them.
Discuss the sizing of the capacitor Cd.
c.
9.
Compute the minimum values of Cc and Cd so that the sense amp sees a differential voltage of at
least 60 mV.
[M, None, 12.3.1] Figure 12.90 shows a dynamic NOR row decoder (using pseudo two-phase logic) for
word line 0 of a memory with 16 word lines.
a.
Explain the operation of this row decoder, showing approximate voltage waveforms for all
important nodes, including the clocks. What is the purpose of gate 2?
b.
Discuss the relative advantages and disadvantages of a dynamic versus a static decoder.
10. [E, None, 12.3.1] Design a column decoder to select one out of 16 bit lines based on address bits A3, A2,
A1, and A0 and their complements. Minimize the total number of transistors while limiting the maximum
number of cascaded pass transistors to three. Draw a transistor-level schematic of your design.
11. [C, None, 12.3.2] A dynamic sense amplifier is shown in a Figure 12.91. The capacitance of each bit
line is 1 pF, and average discharging current from the selected RAM cell equals 10 µA. The waveform
applied at point S is shown in b. Initially, S is high. When BL reaches VDD – 0.5 V (at time t = t1), S is
lowered to VDD – 1.2 V and reaches this value at time t = t2 = t1 + 1 nsec. Determine the sizes of the
various transistors M1 and M2 so that a delay of less than 3 nsec is obtained. Delay is measured starting
at t1 and is defined as the time when BL reaches 2.1 V. VDD = 3.3 V, Vt=0.75V, kn’=19.6uA/V2 (assume
long channel). Complete the waveform for BL.
12. [E&D, None, 12.4.2] Design a hamming-code scheme to correct a single bit in an 11-bit word. How
many check-bits are needed? Design the logic needed to perform the error correction (at the gate level).
It is sufficient to show the logic for a single bit.
13. [E, None, 12.6.1] Implement the following logic functions described by Eq. 12.20 using a dynamic
NAND-NAND PLA. Draw the transistor diagram.
__
f 0 = x 0 x1 + x 2
(12.20)
__
__
f 1 = x 0 x1 x 2 + x 2 + x 0 x1
DESIGN PROBLEM
Design an SRAM array with 64 rows with each row being 32-bits wide. Use
standard, minimum channel length, 6T SRAM cells with a pull-up ratio of 1 and a
cell ratio of 1.2. Estimate the size of the cell. Assuming the minimum width
wires with 0.1fF/µm capacitance and 0.05Ω/□ resistance, estimate the bit line and
word line capacitances. Design a 6-to-64 decoder in complementary CMOS to
drive this wordline load and assuming that the input capacitance is limited to a
transistor width of 24λ.
Input address bits are available as true and
complementary. Divide the decoder in the predecoder and the final wordline
decoder, and include the wire load between the two in your sizing calculation. Use
dynamic bitline loads and dsign the dynamic sense amplifiers, loaded with 24λ
loads. Use the 4:1 output multiplexers.
EECS 141
Fall 1999
Discussion Session
Week #1
9/1/99
Tips for using Hspice
I.
•
•
•
•
Getting Started
Setup the environment:
source /usr/eesww/HSPICE/98.2/bin/cshrc.meta
Run the simulator on your input file:
hspice filename.sp >! filename.lis
Use the waveform viewer to see the output
awaves
Input files must have the extension .sp for the waveform viewer to work.
Also, the input file must have “.OPTION POST=2” specified.
Waveforms can be printed by choosing Tools -> Print...
View the online documentation
acroread /usr/eesww/HSPICE/98.2/docs/hspice.pdf &
The page numbers in the rest of this document refer to this manual.
This file is 11 MB (1714 pages). Do not print it out!
II.
•
•
•
Netlist Format
The input files are case insensitive.
The first line is always a comment. Other lines are commented with a leading * or $
All nonlinear devices must have a .MODEL statement.
Names:
• can contain letters, numbers, and the characters ! # $ % * + - / < > [ ] _ (see p. 3-18)
• can be 1024 characters long
• Node names can begin with letters, numbers, or the characters # _ ! % (see p. 3-19)
• Trailing alphabetic characters are ignored in net names. For example a node named
1A is considered to be equivalent to node 1 (see p. 3-19)
• Nodes named 0, GND, GND!, and GROUND all refer to the global ground node.
III.
Values
Expressing Values:
• Scientific notation: e.g. 1.1e-17
• Use a suffix: e.g. 2.3u (x=mega, k=kilo, m=mili, u=micro, n=nano, p=pico, f=femto)
• Use a parameter: e.g. minlen (parameters must be declared with a .PARAM
statement)
• Evaluated expressions: e.g. ‘500m*minlen’
Output variables:
• Voltage between two nodes: v(n1,n2)
• Voltage of a node relative to ground: v(n1)
• Current through an independent source: i(vin)
IV.
•
•
•
.OP
Operating point, DC circuit solution (see p. 6-8)
.DC
Sweep of DC operating points (capacitances are ignored) (see p. 8-1)
.DC var startval stopval incr - performs a DC sweep on the independent source or
parameter var, varying its value from startval to stopval using the increment incr.
.TRAN
Perform a transient analysis (differential equation solver) (see p. 7-1)
.TRAN tincr tstop – finds the operating point (.OP) and then performs a transient
analysis of duration tstop seconds with a maximum time step of tincr.
V.
•
•
•
•
Control
.INCLUDE – includes a file (see p. 3-60)
.OPTION – sets simulation options (see p. 3-45)
.END – marks the end of an input file
.ALTER – treated as .END, but allows another simulation to be performed with the
changes that follow the .ALTER statement (see p. 3-34)
VI.
•
•
•
•
Analysis
Measurements
.MEASURE TRAN t_delay TRIG v(in) VAL=2.5 CROSS=1 TARG v(out)
VAL=2.5 CROSS=1
Measures the propagation delay between the nodes in and out, where the signals first
cross 2.5 volts.
.MEAS t_rise TRIG v(out) VAL=0.5 RISE=1 TARG v(out) VAL=4.5 RISE=1
Measures the first 10%-90% rise time of a 5V signal
.MEAS TRAN max_current MAX I(Vdd)
Measures the maximum current through the independent source Vdd
.MEAS peak_power PARAM=’max_current*5’
Calculates the peak power, assuming that max_current has been measured
Measured values are placed in a file called filename.mt#. See p. 4-19 for more details.
VII. Troubleshooting
•
Failure to converge (OP and DC) – The DC solver uses an iterative method to find
the operating point, but some circuits exist which have no or multiple operating
points. The best solution is to perform hand analysis of your circuit to make sure that
you haven’t done this.
•
•
No DC Path to ground (OP and DC) – This often happens with floating MOSFET
gates. Just add a resistor between the node and ground, or use the .IC or .NODESET
commands to create an initial condition. Be warned, however, that .NODESET and
.IC can cause convergence problems.
Stability Problems (TRAN) – Sometimes a transient analysis shows a “ringing” or
oscillation that shouldn’t be there. This can often be solved by reducing the
maximum time step or using slower rise and fall times for independent sources.
Send questions to wrdavis@eecs.berkeley.edu ...
Table Of Contents
1
Digital Integrated Circuits—
A Design Perspective (2nd Ed)
Table of Contents
PREFACE
PART I. THE FOUNDATIONS
CHAPTER 1: INTRODUCTION
1.1
A Historical Perspective
1.2
Issues in Digital Integrated Circuit Design
1.3
Quality Metrics of a Digital Design
1.3.1
1.3.2
1.3.3
1.3.4
Cost of an Integrated Circuit
Functionality and Robustness
Performance
Power and Energy Consumption
1.4
Summary
1.5
To Probe Further
Chapter 2: THE MANUFACTURING PROCESS
2.1
Introduction
2.2
Manufacturing CMOS Integrated Circuits
2.2.1
2.2.2
2.2.3
2.2.4
The Silicon Wafer
Photolithography
Some Recurring Process Steps
Simplified CMOS Process Flow
2.3
Design Rules — The Contract between Designer and Process Engineer
2.4
Packaging Integrated Circuits
2.4.1
2.4.2
2.4.3
Package Materials
Interconnect Levels
Thermal Considerations in Packaging
DIGITAL INTEGRATED CIRCUITS
2.5
Perspective — Trends in Process Technology
2.5.1
2.5.2
Short-Term Developments
In the Longer Term
2.6
Summary
2.7
To Probe Further
DESIGN METHODOLOGY INSERT A: IC LAYOUT
CHPATER 3: THE DEVICES
3.1
Introduction
3.2
The Diode
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
A First Glance at the Diode — The Depletion Region
Static Behavior
Dynamic, or Transient, Behavior
The Actual Diode—Secondary Effects
The SPICE Diode Model
The MOS(FET) Transistor
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
A First Glance at the Device
The MOS Transistor under Static Conditions
Dynamic Behavior
The Actual MOS Transistor—Some Secondary Effects
SPICE Models for the MOS Transistor
3.4
A Word on Process Variations
3.5
Perspective: Technology Scaling
3.6
Summary
3.7
To Probe Further
DESIGN METHODOLOGY INSERT B: CIRCUIT SIMULATION
CHAPTER 4: THE WIRE
4.1
Introduction
4.2
A First Glance
4.3
Interconnect Parameters — Capacitance, Resistance, and Inductance
2
Table Of Contents
3
4.3.1
4.3.2
4.3.3
4.4
Electrical Wire Models
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.5
Capacitance
Resistance
Inductance
The Ideal Wire
The Lumped Model
The Lumped RC model
The Distributed rc Line
The Transmission Line
SPICE Wire Models
4.5.1
4.5.2
Distributed rc Lines in SPICE
Transmission Line Models in SPICE
4.6
Perspective: A Look into the Future
4.7
Summary
4.8
To Probe Further
PART II. A CIRCUIT PERSPECTIVE
Chapter 5: THE CMOS INVERTER
5.1
Introduction
5.2
The Static CMOS Inverter — An Intuitive Perspective
5.3
Evaluating the Robustness of the CMOS Inverter: The Static Behavior
5.3.1
5.3.2
5.3.3
5.4
Performance of CMOS Inverter: The Dynamic Behavior
5.4.1
5.4.2
5.4.3
5.5
Switching Threshold
Noise Margins
Robustness Revisited
Computing the Capacitances
Propagation Delay: First-Order Analysis
Propagation Delay from a Design Perspective
Power, Energy, and Energy-Delay
5.5.1
5.5.2
5.5.3
5.5.4
Dynamic Power Consumption
Static Consumption
Putting It All Together
Analyzing Power Consumption Using SPICE
DIGITAL INTEGRATED CIRCUITS
5.6
Perspective: Technology Scaling and its Impact on the Inverter Metrics
5.7
Summary
5.8
To Probe Further
4
CHAPTER 6: DESIGNING COMBINATIONAL LOGIC GATES IN CMOS
6.1
Introduction
6.2
Static CMOS Design
6.2.1
6.2.2
6.2.3
6.3
Dynamic CMOS Design
6.3.1
6.3.2
6.3.3
6.3.4
6.4
Complementary CMOS
Ratioed Logic
Pass-Transistor Logic
Dynamic Logic: Basic Principles
Speed and Power Dissipation of Dynamic Logic
Issues in Dynamic Design
Cascading Dynamic Gates
Perspectives
6.4.1
6.4.2
How to Choose a Logic Style?
Designing Logic for Reduced Supply Voltages
6.5
Summary
6.6
To Probe Further
DESIGN METHODOLOGY INSERT C: HOW TO SIMULATE COMPLEX
LOGIC GATES
C.1
Representing Digital Data as a Continuous Entity
C.2
Representing Data as a Discrete Entity
C.3
Using Higher-Level Data Models
C.4
To Probe Further
DESIGN METHODOLOGY INSERT D: LAYOUT TECHNIQUES FOR
COMPLEX GATES
Table Of Contents
5
CHAPTER 7: DESIGNING SEQUENTIAL LOGIC CIRCUITS
7.1
Introduction
7.1.1
7.1.2
7.2
Static Latches and Registers
7.2.1
7.2.2
7.2.3
7.2.4
7.2.5
7.3
Pulse Registers
Sense-Amplifier Based Registers
Pipelining: An approach to optimize sequential circuits
7.5.1
7.5.2
7.6
Dynamic Transmission-Gate Edge-triggered Registers
C2MOS—A Clock-Skew Insensitive Approach
True Single-Phase Clocked Register (TSPCR)
Alternative Register Styles*
7.4.1
7.4.2
7.5
The Bistability Principle
Multiplexer-Based Latches
Master-Slave Edge-Triggered Register
Low-Voltage Static Latches
Static SR Flip-Flops—Writing Data by Pure Force
Dynamic Latches and Registers
7.3.1
7.3.2
7.3.3
7.4
Timing Metrics for Sequential Circuits
Classification of Memory Elements
Latch- vs. Register-Based Pipelines
NORA-CMOS—A Logic Style for Pipelined Structures
Non-Bistable Sequential Circuits
7.6.1
7.6.2
7.6.3
The Schmitt Trigger
Monostable Sequential Circuits
Astable Circuits
7.7
Perspective: Choosing a Clocking Strategy
7.8
Summary
7.9
To Probe Further
DIGITAL INTEGRATED CIRCUITS
6
PART III. A SYSTEM PERSPECTIVE
CHAPTER 8: IMPLEMENTATION STRATEGIES FOR DIGITAL ICS
8.1
Introduction
8.2
From Custom to Semicustom and Structured Array Design Approaches
8.3
Custom Circuit Design
8.4
Cell-Based Design Methodology
8.4.1
8.4.2
8.4.3
8.4.4
8.5
Standard Cell
Compiled Cells
Macrocells, Megacells and Intellectual Property
Semi-Custom Design Flow
Array-Based Implementation Approaches
8.5.1
8.5.2
Pre-diffused (or Mask-Programmable) Arrays
Pre-wired Arrays
8.6
Perspective—The Implementation Platform of the Future
8.7
Summary
8.8
To Probe Further
DESIGN METHODOLOGY INSERT E: CHARACTERIZING LOGIC AND
SEQUENTIAL CELLS
DESIGN METHODOLOGY INSERT F: DESIGN SYNTHESIS
CHAPTER 9: COPING WITH INTERCONNECT
9.1
Introduction
9.2
Capacitive Parasitics
9.2.1
9.2.2
9.3
Resistive Parasitics
9.3.1
9.3.2
9.3.3
9.4
Capacitance and Reliability—Cross Talk
Capacitance and Performance in CMOS
Resistance and Reliability—Ohmic Voltage Drop
Electromigration
Resistance and Performance—RC Delay
Inductive Parasitics
Table Of Contents
7
9.4.1
9.4.2
9.5
Inductance and Reliability— Voltage Drop
Inductance and Performance—Transmission Line Effects
Advanced Interconnect Techniques
9.5.1
9.5.2
Reduced-Swing Circuits
Current-Mode Transmission Techniques
9.6
Perspective: Networks-on-a-Chip
9.7
Chapter Summary
9.8
To Probe Further
CHAPTER 10: TIMING ISSUES IN DIGITAL CIRCUITS
10.1
Introduction
10.2
Timing Classification of Digital Systems
10.2.1 Synchronous Interconnect
10.2.2
10.2.3
10.2.4
10.3
Synchronous Design — An In-depth Perspective
10.3.1
10.3.2
10.3.3
10.3.4
10.4
Synchronizers—Concept and Implementation
Arbiters
Clock Synthesis and Synchronization Using a Phase-Locked Loop
10.6.1
10.6.2
10.7
Self-Timed Logic - An Asynchronous Technique
Completion-Signal Generation
Self-Timed Signaling
Practical Examples of Self-Timed Logic
Synchronizers and Arbiters*
10.5.1
10.5.2
10.6
Synchronous Timing Basics
Sources of Skew and Jitter
Clock-Distribution Techniques
Latch-Based Clocking *
Self-Timed Circuit Design*
10.4.1
10.4.2
10.4.3
10.4.4
10.5
Mesochronous interconnect
Plesiochronous Interconnect
Asynchronous Interconnect9
Basic Concept
Building Blocks of a PLL
Future Directions and Perspectives
10.7.1
Distributed Clocking Using DLLs
DIGITAL INTEGRATED CIRCUITS
10.7.2
10.7.3
Optical Clock Distribution
Synchronous versus Asynchronous Design
10.8
Summary
10.9
To Probe Further
DESIGN METHODOLOGY INSERT G: DESIGN VERIFICATION
CHAPTER 11: DESIGNING ARITHMETIC BUILDING BLOCKS
11.1
Introduction
11.2
Datapaths in Digital Processor Architectures
11.3
The Adder
11.3.1
11.3.2
11.3.3
11.4
The Multiplier
11.4.1
11.4.2
11.4.3
11.4.4
11.4.5
11.5
The Binary Adder: Definitions
The Full Adder: Circuit Design Considerations
The Binary Adder: Logic Design Considerations
The Multiplier: Definitions
Partial-Product Generation
Partial Product Accumulation
Final Addition
Multiplier Summary
The Shifter
11.5.1
11.5.2
Barrel Shifter
Logarithmic Shifter
11.6
Other Arithmetic Operators
11.7
Power and Speed Trade-off’s in Datapath Structures
11.7.1
11.7.2
11.7.3
Design Time Power-Reduction Techniques
Run-Time Power Management
Reducing the Power in Standby (or Sleep) Mode
11.8
Perspective: Design as a Trade-off
11.9
Summary
11.10 To Probe Further
8
Table Of Contents
9
CHAPTER 12: DESIGNING MEMORY AND ARRAY STRUCTURES
12.1
Introduction
12.1.1
12.1.2
12.2
The Memory Core
12.2.1
12.2.2
12.2.3
12.2.4
12.3
Signal-To-Noise Ratio
Memory yield
Power Dissipation in Memories
12.5.1
12.5.2
12.5.3
12.5.4
12.5.5
12.6
The Address Decoders
Sense Amplifiers
Voltage References
Drivers/Buffers
Timing and Control
Memory Reliability and Yield
12.4.1
12.4.2
12.5
Read-Only Memories
Nonvolatile Read-Write Memories
Read-Write Memories (RAM)
Contents-Addressable or Associative Memory (CAM)
Memory Peripheral Circuitry
12.3.1
12.3.2
12.3.3
12.3.4
12.3.5
12.4
Memory Classification
Memory Architectures and Building Blocks
Sources of Power Dissipation in Memories
Partitioning of the memory
Addressing the Active Power Dissipation
Data-retention dissipation
Summary
Case Studies in Memory Design
12.6.1
12.6.2
12.6.3
The Programmable Logic Array (PLA)
A 4 Mbit SRAM
A 1 Gbit NAND Flash Memory
12.7
Perspective: Semiconductor Memory Trends and Evolutions
12.8
Summary
12.9
To Probe Further
DIGITAL INTEGRATED CIRCUITS
DESIGN METHODOLOGY INSERT H: VALIDATION AND TEST OF
MANUFACTURED CIRCUITS
H.1
Introduction
H.2
Test Procedure
H.3
Design for Testability
H.3.1
H.3.2
H.3.3
H.3.4
H.3.5
H.4
Issues in Design for Testability
Ad Hoc Testing
Scan-Based Test
Boundary-Scan Design
Built-in Self-Test (BIST)
Test-Pattern Generation
H.4.1 Fault Models
H.4.2 Automatic Test-Pattern Generation (ATPG)
H.4.3
H.5
Fault Simulation
To Probe Further
INDEX
10