Search Results (293)

Pb-contaminated soil poses serious hazards to humans and ecosystems and is in urgent need of remediation. However, the extensive use of traditional curing materials such as ordinary Portland cement (OPC) has negatively impacted global ecology and the climate, so there is a need to explore low-carbon and efficient green cementitious materials for the immobilization of Pb-contaminated soils. A red mud/steel slag-based (RM/SS) geopolymer was designed and the potential use of solidifying/stabilizing heavy metal Pb pollution was studied. The Box–Behnken design (BBD) model was used to design the response surface, and the optimal preparation conditions of RM/SS geopolymer (RSGP) were predicted by software of Design-Expert 8.0.6.1. The microstructure and phase composition of RSGP were studied by X-ray diffractometer, Fourier transform infrared spectrometer, scanning electron microscopy and X-ray photoelectron spectroscopy, and the immobilization mechanism of RSGP to Pb was revealed. The results showed that when the liquid–solid ratio is 0.76, the mass fraction of RM is 79.82% and the modulus of alkali activator is 1.21, the maximum unconfined compressive strength (UCS) of the solidified soil sample is 3.42 MPa and the immobilization efficiency of Pb is 71.95%. The main hydration products of RSGP are calcium aluminum silicate hydrate, calcium silicate hydrate and nekoite, which can fill the cracks in the soil, form dense structures and enhance the UCS of the solidified soil. Pb is mainly removed by lattice immobilization, that is, Pb participates in geopolymerization by replacing Na and Ca to form Si-O-Pb or Al-O-Pb. The remaining part of Pb is physically wrapped in geopolymer and forms Pb(OH)₂ precipitate in a high-alkali environment. Full article

River silt deposited by water in coastal areas is unsuitable for engineering construction. Thus, the in situ stabilization treatment of river silt as the bearing layer has been an important research area in geotechnical engineering. The strength degradation behavior and mechanism of stabilized river silt reinforced with cement and alginate fibers (AFCS) in different engineering environments are crucial for engineering applications. Therefore, freeze–thaw (F–T) cycle tests, wetting-drying (W–D) cycle tests, water immersion tests and seawater erosion tests were conducted to explore the strength attenuation of stabilized river silt reinforced with the same cement content (9% by wet weight) and different fiber contents (0%, 0.3%, 0.6% and 0.9% by weight of wet soil) and fiber lengths (3 mm, 6 mm and 9 mm). The reinforcement and damage mechanism of AFCS was analyzed by scanning electron microscopy (SEM) imaging. The results indicate that the strength of AFCS was improved from 84% to 180% at 15 F–T cycle tests, and the strength of AFCS was improved by 26% and 40% at 30 W–D cycles, which showed better stability and excellent characteristics owing to the hygroscopic characteristics of alginate fiber arousing the release of calcium and magnesium ions within the alginate. Also, the strength attenuation of AFCS was reduced with the increase in the length and content of alginate fibers. Further, the strength of specimens in the freshwater environment was higher than that in the seawater environment at the same fiber content, and the softening coefficient of AFCS in the freshwater environment was above 0.85, indicating that the AFCS had good water stability. The optimal fiber content was found to be 0.6% based on the unconfined compressive strength (UCS) reduction in specimens cured in seawater and a freshwater environment. And the strength of AFCS was improved by about 10% compared with that of cement-stabilized soil (CS) in a seawater environment. A stable spatial network structure inside the soil was formed, in which the reinforcing effect of fibers was affected by mechanical connection, friction and interfacial bonding. However, noticeable cracks developed in the immersed and F–T specimens. These microscopic characteristics contributed to decreased mechanical properties for AFCS. The results of this research provide a reference for the engineering application of AFCS. Full article

This article focuses on the search for efficient solutions to enhance the mechanical strength of geomaterials, especially soils, with crucial applications in civil engineering. Four promising materials are explored as soil improvement agents: natural latex (rubber trees), lignosulfonate (paper industry byproduct), xanthan gum (bacterial fermentation), and eggshell lime. While other sustainable options exist, these four were chosen for their distinct characteristics and potential for further study. Natural latex, derived from rubber trees, demonstrates exceptional potential for strengthening the mechanical resistance of soils, offering a path to effective stabilization without compromising environmental sustainability. Lignosulfonate, a paper industry byproduct, emerges as an alternative that can significantly enhance the load-bearing capacity of soils, boosting its applicability in civil engineering projects. Xanthan gum, produced through bacterial fermentation, possesses unique properties that increase soil cohesion and strength, making it a valuable option for geotechnical applications. Finally, despite potential challenges, eggshell lime shows promising potential in enhancing the mechanical resistance of soils. This study highlights the importance of evaluating and comparing these agents in terms of their effectiveness in improving the mechanical strength of soils in civil engineering applications. In the literature review, the impact of stabilizer addition (%) was examined for the four cementing agents studied, along with its influence on key soil properties like optimum moisture content (OMC, %), maximum dry density (MDD, gm/cc), California bearing ratio (CBR, %), uniaxial compressive strength (UCS) at 28 days (MPa), and the change in UCS (ΔUCS, %) among other physicochemical parameters. Appropriate selection of these materials can lead to developing more robust and sustainable geomaterials, promoting significant advancements in geotechnical engineering and civil construction practices. To evaluate their effectiveness, the efficiency of one of them was assessed experimentally. Xanthan gum (XG) was selected to biopolymerize clay soil. Specimens were prepared for strength and stiffness tests, including unconfined compression, scanning electron microscopy (SEM), and ultrasonic wave analysis. The impact of stabilizer concentration was examined (e.g., 1%, 3%, 5% xanthan gum) to assess how dosage affects the soil–stabilizer mixture. The results showed that the rubber increases the unconfined compression and stiffness of the soil, controlled by the XG’s porosity/volumetric quantity ratio. The research demonstrates the potential of XG, but a broader analysis of all four materials with the outlined testing methods paves the way for future advancements in geotechnical engineering. Full article

Water treatment sludge (WTS) is the residue produced during water treatment processes for public use. Exploring the reintroduction of these wastes into the production chain to generate new, value-added materials presents a current challenge. This could promote their reuse and reduce the negative environmental impacts associated with their disposal. This study assessed the technical feasibility of using aluminum-based WTS to partially replace silty sand soil in mixtures that include two stabilizers (hydrated lime and Portland cement), potentially for use in road pavements. After conducting a thorough physical, chemical, and geotechnical characterization of both the soil and the sludge, bench-scale experiments were carried out to test the mixtures’ resistance, with WTS proportions of 5%, 8%, 10%, 15%, and 20%, stabilized with either lime or cement. The findings confirm that WTS does not contain potentially toxic elements, according to Brazilian standards, and all tested composites appear suitable for paving. However, the mechanical resistance of the soil–sludge–cement mixtures decreases as the WTS content increases, with an optimum California bearing ratio (CBR) of 41.50% achieved at a 5% WTS addition. Meanwhile, incorporating 15% WTS into soil–sludge–lime mixtures resulted in the highest CBR value of 21.25% for this type of mixture. It is concluded that incorporating stabilizers into soil–WTPS mixtures for road construction allows for an increased percentage of WTPS in silty-sandy soils. Further studies are recommended with different soil types and the addition of fibers to the mixes, to assess the long-term performance of the structure, along with economic and environmental analyses. Full article

Affected by climate warming and anthropogenic disturbances, the thermo-mechanical stability of warm and ice-rich frozen ground along the Qinghai–Tibet Railway (QTR) is continuously decreasing, and melting subsidence damage to existing warm frozen soil (WFS) embankments is constantly occurring, thus seriously affecting the stability and safety of the existing WFS embankments. In this study, in order to solve the problems associated with the melting settlement of existing WFS embankments, a novel reinforcement technology for ground improvement, called an inclined soil–cement continuous mixing wall (ISCW), is proposed to reinforce embankments in warm and ice-rich permafrost regions. A numerical simulation of a finite element model was conducted to study the freeze–thaw process and evaluate the stabilization effects of the ISCW on an existing WFS embankment of the QTR. The numerical investigations revealed that the ISCW can efficiently reduce the melt settlement in the existing WFS embankment, as well as increase the bearing capacity of the existing WFS embankment, making it favorable for improving the bearing ability of composite foundations. The present investigation breaks through the traditional ideas of “active cooling” and “passive protection” and provides valuable guidelines for the choice of engineering supporting techniques to stabilize existing WFS embankments along the QTR. Full article

The unconfined compressive strength (q_u) weakness of low-compressibility clay (CL) reduces its structural safety. As part of the present study, waste glass powder (WGP) was mixed with Portland cement to improve the geotechnical properties of clayey soil, thus contributing to sustainability through the recycling of municipal waste. Based on the stiffness and chemical composite of WGP and cement, the adopted mixing ratio of the mixed soil was 10% and 20% WGP and 3% and 6% cement. The soil mixing ratio was selected and tested considering the percentage of the cement, WGP, water/cement ratio, dry unit weight, porosity of the specimen, and curing times of 7 days and 28 days. SEM-EDS tests were conducted to examine the impact of raw materials on the microstructural mixed soil. The results from SEM-EDS show that the cement–WGP–CL mixture caused different degrees of cementation and bonding products. Modifying multiple layers of water in the particle of the clay surface led to the enhancement of the interaction of the interlayer of hydrated clay, achieving the best unconfined compressive strength and stiffness of the designed specimen. From the viewpoint of unconfined compressive strength and stiffness enhancement, blending content of 20% WGP and 6% cement and dry unit weights compaction was recommended for stabilizing CL. The process of q_u and stiffness improving CL involved an optimized mixing ratio and particle densification reaction efficiency. The soil’s q_u and stiffness were predicted using ANN (artificial neural networks) and the porosity/cement index was predicted based on the experimental results. Full article

MgO carbonization is a green and low-carbon soil improvement technology. The use of MgO carbonization to solidify dredged sediment and transform it into road-building materials has significant environmental sustainability advantages. A series of microscopic characterization tests, including X-ray Diffraction (XRD), Scanning Electron Microscope–Energy Dispersive Spectrometer (SEM-EDS), and Mercury-in-Pressure (MIP) tests, were conducted to elucidate the evolution characteristics of mineral composition, microscopic morphology, and pore structure of sediment under carbonation. Based on the results, the mechanism of MgO carbonation–solidification of dredged sediment was explored. In order to verify the improvement of carbonation on the road performance of sediment, comparative tests were carried out on sediment, non-carbonated sediment, and carbonated sediment. The results indicate a significant improvement in the solidification of MgO-treated sediment through carbonation, with enhanced macroscopic strength and densified microscopic structure. This can be attributed to the encapsulation, cementation, and pore-filling effects of the hydration products and carbonation products of MgO on soil particles. The rebound modulus and splitting strength of carbonated sediment were 3.53 times and 2.16 times that of non-carbonated sediment, respectively. Additionally, the carbonated sediment showed improved saturated stability, resistance to salt solution wet–dry cycles, and resistance to freeze–thaw cycles. Full article

Cement-stabilized soil is a commonly used pavement base/bottom base material. Adding a suitable curing agent to cement-stabilized soil can effectively reduce the dosage of cement, meet the strength requirements, and also greatly improve its water stability. In this paper, three kinds of cement dosage (6%, 8%, and 10%) of cement-stabilized soil were selected to add a 0.04% organic liquid curing agent, and then compared with high-dose cement (10% and 12%)-stabilized soil. The influence of wetting–drying cycles on the mechanical properties of the five stabilized soils was discussed. The mineral composition of cement-stabilized soils before and after the addition of a curing agent was analyzed by X-ray diffraction (XRD), and the microscopic morphology of 10% cement-stabilized soils with a curing agent was studied by scanning electron microscopy (SEM). The macroscopic test shows that the unconfined compressive strength of solidified cement-stabilized soil can be divided into three stages with the increase in the times of the wetting–drying cycles, which are the rapid decay stage, stable enhancement stage, and stable decay stage. The wetting–drying stability coefficient first increases, and then decreases with the increase in the times of the wetting–drying cycles. The microscopic test shows that the addition of a curing agent can enhance the content of hydration products in the cement-stabilized soil specimen; at the curing age of 28 d, with the increase in the times of the wet–dry cycles, the structure of the solidified cement-stabilized soil gradually broke down. The surface porosity P and pore diameter d showed an overall upward trend but decreased at the fifth wetting–drying cycle. The pore orientation weakened. The results show that the resistance of cement-stabilized soil with a curing agent is obviously better than that of cement-stabilized soil under wet–dry conditions. Full article

The alkali-activated composites technique is a promising method for the in situ preparation of cavity filling/grouting materials from engineering waste soil. To investigate the feasibility of engineering waste soil utilization by the alkali activation process, the macroscopic and microscopic properties of the fly ash/slag-based alkali-activated composites, after solidification/stabilization (S/S) with sandy clay excavated at Baishitang Station of Shenzhen Metro, were studied. The unconfined compressive strength (UCS) test was conducted to evaluate the S/S effect of alkali-activated composites. The results show that the optimum quality ratio of slag and fly ash correspond to 7:3, the modulus of alkaline activator to 1.3, and the alkalinity of alkaline activator to 10%. The alkali-activated composite’s strength under these parameters can reach 45.25 MPa at 3 days, 49.85 MPa at 7 days, and 62.33 MPa at 28 days. A maximum 3-day UCS of 21.71 MPa, 75% of the 28-day UCS, was achieved by an engineering waste soil and alkali-activated composites mass ratio of 5:5, slaked lime content of 4.5%, and a water-to-solid ratio of 0.26, and it can also meet the required fluidity and setting time for construction well. Fluidity is primarily affected by the soil-to-binder ratio, which decreases as the ratio decreases, while the water-to-solid ratio increases fluidity. Slaked lime has minimal impact on fluidity. The setting time is mainly influenced by the soil-to-binder ratio, followed by slaked lime content and water-to-solid ratio, with setting time shortening as the soil-to-binder ratio and slaked lime content increase, and lengthening as the water-to-solid ratio increases. Through Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS) tests, microscopic analysis showed that loose granular units are firmly cemented by alkali-activated composites. Based on the results of on-site grouting tests in karst caves, the alkali-activated grout materials reached a strength of 5.2 MPa 28 days after filling, which is 162.5% of the strength of cement grouting material, satisfying most of the requirements for cavity filling in Shenzhen. Full article

The prediction of the ultimate bearing capacity (UBC) of composite foundations represents a critical application of test monitoring data within the field of intelligent geotechnical engineering. This paper introduces an effective combinational prediction algorithm, namely SA-IRMO-BP. By integrating the Improved Radial Movement Optimization (IRMO) algorithm with the simulated annealing (SA) algorithm, we develop a meta-heuristic optimization algorithm (SA-IRMO) to optimize the built-in weights and thresholds of backpropagation neural networks (BPNN). Leveraging this integrated prediction algorithm, we forecast the UBC of soil–cement mixed (SCM) pile composite foundations, yielding the following performance metrics: RMSE = 3.4626, MAE = 2.2712, R = 0.9978, VAF = 99.4339. These metrics substantiate the superior predictive performance of the proposed model. Furthermore, we utilize two distinct datasets to validate the generalizability of the prediction model presented herein, which carries significant implications for the safety and stability of civil engineering projects. Full article

Due to the high degree of weathering, the red clay slope has low anti-disintegration performance, and the clay easily becomes wet and disintegrates after soaking in water. It causes geological problems such as slope collapse caused by soil softening. To study the disintegration characteristics of modified red clay, the disintegration test of red clay modified by using lignin fiber, clay particles and lime was carried out, analyzing the disintegration characteristics of improved red clay from physical and chemical perspectives and analyzing the improvement mechanism of three modifiers with the scanning electron microscopy test. The analysis results show that the water-holding capacity and disintegration resistance of soil mixed with lignin fiber decrease; the disintegration time of reshaped red clay increases with the increase in clay content; and the average disintegration rate of the soil decreases with the increase in clay content. With the increase in lime content, the soil cement increases. The integrity of the soil is enhanced, and its anti-disintegration ability is improved; the saturated moisture content of reshaped red clay increases with the increase in lignin fiber and clay content, while the saturated moisture content of soil decreases with the increase in lime content. The damage analysis shows that the larger the damage factor of soil, the worse its anti-disintegration ability, and the easier the soil disintegrates. The purpose of this paper is to explore the essence of the soil disintegration phenomenon, and on this basis, using high-quality improved materials, to improve the soil, which easily disintegrates. This move aims to significantly enhance the anti-disintegration ability of the soil, thereby improving its resistance to softening and disintegration, thereby effectively improving and maintaining the ecological environment. At the same time, the improved soil will help to improve the utilization rate of the slope and foundation soil, thereby reducing the economic cost of maintenance engineering. Against the current background of sustainable economic, social, and ecological development, it is of great strategic significance to ensure the sustainable availability of land resources in specific areas and maintain their productivity and ecological stability for a long time. The research into this subject not only helps to deepen the understanding of soil disintegration, but also provides strong technical support for the rational utilization of land resources and the protection of the ecological environment. Full article

The cement composite calcium lignosulfonate is used to enhance the mechanical properties and the freeze–thaw resistance of loess. Based on an unconfined compressive test under different freeze–thaw cycles, the influence of cement dosage, curing age, and freeze–thaw cycles on compressive strength are discussed. The results indicate that the strength of loess can increase by up to 13 times, and the loss of strength is reduced from 72% to 28% under the reinforcement of cement dosage and curing age. The loss of strength is mainly concentrated in the initial 5 freeze–thaw cycles, and the structure gradually stabilizes after 10 freeze–thaw cycles. In addition, according to the X-ray diffraction test, it is found that the stabilized loess exhibits a comparatively more stable mineral composition. The scanning electron microscope results reveal that hydration products enveloped the soil particles, forming a mesh structure that strengthens the connection between the soil particles. The freeze–thaw damage makes the small and medium pores turn into large pores in loess, while the stabilized loess changes micro and small pores into small and medium pores, with no large pores found. It is feasible to improve loess with the cement composite calcium lignosulfonate, which can provide references for the reinforcement treatment of loess. Full article

Due to volume change and low strength, fine-grained soils are problematic in construction. Stabilization with cement and sawdust ash (SDA) by-products can improve engineering properties. This study aimed to investigate the effectiveness of cement and sawdust ash (SDA) in stabilizing fine-grained soils for liner applications. Varying proportions of cement (0–9%) and SDA (0–10%) were added to soil samples (n = 24). Specimens were tested for unconfined compressive strength (UCS), hydraulic conductivity (HC), and volumetric shrinkage strain (VSS). Two-way ANOVA analyzed stabilization effects. Optimal stabilization occurred with 6% cement and 6% SDA, resulting in significant increases in UCS (51 to 375 kN/m²) and decreases in HC (1.7 × 10⁻⁸ to 4.7 × 10⁻¹⁰ m/s) and VSS (12.8 to 3.51%) compared to untreated soil. ANOVA indicated that both cement and SDA had statistically significant (p < 0.05) effects on improving all three engineering properties. The addition of 6% cement and 6% SDA significantly improved the expansive soil’s strength, hydraulic conductivity, and volume change properties. ANOVA confirmed the quantitative improvements and the significance of both stabilizers. Stabilization using the by-product SDA has the potential to be a sustainable soil improvement method. Full article

During shield construction in underground spaces, synchronous grouting slurry is poured between the surrounding rock and tunnel lining to ensure stability. For synchronous grouting slurries, few studies have investigated the relationship between the rheological parameters and physical properties, grout-segregation mechanism, and anti-segregation performance. Therefore, we explored the relationships between the slurry rheological parameters, segregation rate, and bleeding rate. Cement, sand, fly ash, and bentonite were used to prepare the slurry, and the effects of different polycarboxylate water-reducing agents and dispersible latex powder dosages were studied. The rheological parameters of 16 groups of uniformly designed slurries were tested, and the data were fit using the Herschel–Bulkley model. The optimal mix ratio lowered the slurry segregation rate, and its rheological behaviour was consistent with the Herschel–Bulkley fluid characteristics. High-yield-shear-stress synchronous grouting slurries with high and low viscosity coefficients were less likely to bleed and segregate, respectively. The optimised slurry fluidity, 3 h bleeding rate, 24 h bleeding rate, segregation rate, coagulation time, and 28 days compressive strength were 257.5 mm, 0.71%, 0.36%, 3.1%, 6.7 h, and 2.61 MPa, respectively, which meet the requirements of a synchronous grouting slurry of shield tunnels for sufficiently preventing soil disturbance and deformation in areas surrounding underground construction sites. Full article

Land use changes modify soil properties, including aggregate structure, and thus, profoundly affect soil quality and health. However, the effects of land use changes originating from alpine grassland on soil aggregates and aggregate-associated organic carbon have received little attention. Soil aggregate fraction, aggregate-associated organic carbon and relevant influencing factors were determined at 0–20, 20–40 cm soil layers for alpine grassland, cropland and abandoned land in the eastern Qinghai–Tibet Plateau (QTP), and their relationships were analyzed by partial least square regression (PLSR). Results showed the following: (1) conversion from alpine grassland to cropland resulted in a significant decline macroaggregate fraction (R_0.25), mean weight diameter (MWD), mean weight diameter (GMD), soil organic carbon (SOC), and microaggregate-associated SOC; (2) almost all aggregate stability indexes, SOC, and aggregate-associated SOCs were significantly positively correlated with silt and glomalin, suggesting that the binding of fine particles (silt) with the organic cementing agent (glomalin) was probably a key mechanism of SOC formation and aggregate stability in the studied region; (3) compared with biotic factors such as SOC, glomalin and root biomass, abiotic factors including silt and sand can better predict aggregate stability and SOC fraction using the PLSR model. The above results indicated that the conversion of alpine grassland to other land use types in high altitude areas would destroy soil structure and decrease soil organic carbon content, and then reduce soil quality. Full article