Search Results (11,489)

Buildings characterized by high energy consumption necessitate the implementation of efficient multi-energy complementary systems to achieve energy conservation and emission reduction objectives. College dining halls use a lot more electricity than typical residential buildings, despite their relatively small size. The dining hall at the Dongshan Campus of Shanxi University is employed as a representative case study in this research. By utilizing DeST 3.0 software, a comprehensive dynamic load analysis is conducted to estimate the annual energy consumption of the dining hall, with the ultimate goal of an energy-saving system being proposed based on the analysis results. Leveraging DeST 3.0 software, dynamic load characteristics were assessed, revealing an annual energy consumption of 2.39 × 10⁶ kWh for the dining hall. Cooling accounted for 0.91 × 10⁶ kWh, while heating requirements amounted to 0.24 × 10⁶ kWh. These findings illustrate peak power consumption trends, seasonal variations, and potential avenues for energy conservation. To satisfy the heating, cooling, and electricity demands of the dining hall, an integrated energy system incorporating solar and wind energy, as well as utilizing restaurant kitchen garbage as a biomass source, was proposed. This study compares two solar energy utilization systems: photothermal and photovoltaic, with total capacities of 2.375 × 10⁶ kWh and 2.52 × 10⁶ kWh, respectively. The research outcomes underscore that Strategy 2, which integrates a photovoltaic system with wind and biomass energy, emerges as the optimal approach for load management. Ultimately, this investigation demonstrates the feasibility and promise of constructing a hybrid renewable energy system within a college dining hall setting, aligning with sustainability objectives and global trends toward environmentally responsible energy solutions. Full article

When it comes to computing the values of variables defining the preliminary sizing of an airship, a few standardized approaches are available in the existing literature. However, when including a disruptive technology in the design is required, sizing procedures need to be amended, so as to be able to deal with the features of any additional novel item. This is the case of atmospheric ionic thrusters, a promising propulsive technology based on electric power, where thrusters feature no moving parts and are relatively cheap to manufacture. The present contribution proposes modifications to an existing airship design technique, originally conceived accounting for standard electro-mechanical thrusters, so as to cope with the specific features of new atmospheric ionic thrusters. After introducing this design procedure in detail, its potential is tested by showing results from feasibility studies on an example airship intended for a high-altitude mission. Concurrently, the so-obtained results allow the demonstration of the sizing features corresponding to the adoption of atmospheric ionic thrusters at the current level of technology, comparing them to what is obtained for the same mission when employing a standard electro-mechanical propulsion system. Full article

The transition towards a sustainable and renewable energy future is essential to mitigate climate change and reduce greenhouse gas emissions. Small–medium combined heat and power (CHP) systems are increasingly popular for distributed energy generation, as they offer improved energy efficiency and reduced emissions compared to traditional power generation systems. This article reviews recent research articles related to small–medium CHP systems, including their role in renewable energy systems, use of biofuels, steam injection, diagnostics, and carbon capture. Throughout the research, the high potential of coastal regions has been observed and studied as a solid base for the later development of CHP systems. Based on the reviewed literature, the highest potential solutions are proposed to be further investigated as an efficient, economical solution for generating electricity and heat for various small-scale applications. Full article

Ecofuels and their feedstock come in three main product classes: electrofuels (e-Fuels), biofuels, and non-biowaste-derived fuels. Ecofuels originate from non-fossil sources, derived from circular raw materials such as non-food organic waste, renewable hydrogen, and captured CO₂ through a rapid process of carbon fixation. Proposed regulation drafts under discussion indicate that new fuels would need to reach a substantial degree of climate neutrality. The manufacture of all ecofuels, however, requires energy input to accomplish the conversion of the initial feedstock; their climate neutrality claims stem from the use of renewable electric energy and/or biomasses in the production process, but fossil fuels are still the main primary sources of global (and the EU’s) electric power, and most biofuels consumed in the EU transport mix are still crop-based, with potential conflicts with food and land use. Furthermore, entirely neglecting GHG emissions from renewable energy generation is scientifically debatable, as the impact of the energy (and the related GHG emissions) embedded in the materials used to build renewable energy facilities is small, but not nil. The paper reports ecofuel trends according to the above-mentioned originating technologies and discusses the issues related to their development. Full article

This paper presents the methodology developed for underwater measurements using electrochemical impedance spectroscopy (EIS) technique, aimed at determining the resistance of an epoxy coating applied in seawater to the legs of an oil production platform. Performing such underwater tests in an offshore environment was technically challenging. The results of measurements obtained on the platform were confronted with comparative results obtained in the laboratory, where the properties of the coating applied in water collected from the Baltic Sea (thickness, hardness, adhesion, and electrical resistance) were examined. This made it possible to conclude about the correctness of the paint coating application by divers on the legs of the platform. The single-layer epoxy coating applied by brush to the platform legs had a resistance above 10 kΩ∙cm² and thus met the assumed minimum resistance of the protective coating cooperating with cathodic protection as the anti-corrosion protection system of the platform legs. The synergy of these two technologies ensures full protection of offshore structures against corrosion. Measurements of the potential of the platform legs confirmed this. Before painting, the potential value at a depth of 0–15 m was 310 ÷ 320 mV versus the zinc reference electrode, while after painting the potential value decreased to 220 ÷ 240 mV, which means that the effect of full cathodic protection was achieved and the platform legs were protected from corrosion. The developed methodology for underwater EIS measurements on the high seas can be applied to any underwater metal structure to assess the quality of protective coatings. Full article

The chemical bath deposition (CBD) process enables the deposition of ZnO nanowires (NWs) on various substrates with customizable morphology. However, the hydrogen-rich CBD environment introduces numerous hydrogen-related defects, unintentionally doping the ZnO NWs and increasing their electrical conductivity. The oxygen-based plasma treatment can modify the nature and amount of these defects, potentially tailoring the ZnO NW properties for specific applications. This study examines the impact of the average ion energy on the formation of oxygen vacancies (V_O) and hydrogen-related defects in ZnO NWs exposed to low-pressure oxygen plasma. Using X-ray photoelectron spectroscopy (XPS), 5 K cathodoluminescence (5K CL), and Raman spectroscopy, a comprehensive understanding of the effect of the oxygen ion energy on the formation of defects and defect complexes was established. A series of associative and dissociative reactions indicated that controlling plasma process parameters, particularly ion energy, is crucial. The XPS data suggested that increasing the ion energy could enhance Fermi level pinning by increasing the amount of V_O and favoring the hydroxyl group adsorption, expanding the depletion region of charge carriers. The 5K CL and Raman spectroscopy further demonstrated the potential to adjust the ZnO NW physical properties by varying the oxygen ion energy, affecting various donor- and acceptor-type defect complexes. This study highlights the ability to tune the ZnO NW properties at low temperature by modifying plasma process parameters, offering new possibilities for a wide variety of nanoscale engineering devices fabricated on flexible and/or transparent substrates. Full article

This study aims to recover the main by-product of Citrus fruits processing, the raw pomace, known also as pastazzo, to produce plant complexes to be used in the treatment of inflammatory bowel disease (IBD). Food-grade extracts from orange (OE) and lemon (LE) pomace were obtained by ultrasound-assisted maceration. After a preliminary phytochemical and biological screening by in vitro assays, primary and secondary metabolites were characterized by proton nuclear magnetic resonance (¹H-NMR) and liquid chromatography coupled to diode array detection and electrospray ionization mass spectrometry (LC-DAD-ESI-MS) analyses. The intestinal bioaccessibility and antioxidant and anti-inflammatory properties were investigated by in vitro simulated gastro-intestinal digestion followed by treatments on a lipopolysaccharide (LPS)-stimulated human colorectal adenocarcinoma cell line (Caco-2). The tight junctions-associated structural proteins (ZO-1, Claudin-1, and Occludin), transepithelial electrical resistance (TEER), reactive oxygen species (ROS)-levels, expression of some key antioxidant (CAT, NRF2 and SOD2) and inflammatory (IL-1β, IL-6, TNF-α, IL-8) genes, and pNFkB p65 nuclear translocation, were evaluated. The OE and LE digesta, which did not show any significant difference in terms of phytochemical profile, showed significant effects in protecting against the LPS-induced intestinal barrier damage, oxidative stress and inflammatory response. In conclusion, both OE and LE emerged as potential candidates for further preclinical studies on in vivo IBD models. Full article

Only a few recent studies report direct assessment or monitoring of light levels in the indoor learning environment, and no consensus exists on minimum exposures for children’s health. For instance, myopia is a common progressive condition, with genetic and environmental risk factors. Reduced daylight exposure, electric lighting changes, increased near-work for school children, greater academic focus, and use of display screens and white boards may have important detrimental influences. Published assessment methods had varied limitations, such as incomplete compliance from participants wearing light loggers for extended periods. Climate-Based Daylight Modelling is encouraged in UK school design, but design approaches are impractical for post-occupancy assessments of pre-existing classrooms or ad hoc modifications. In this study, we investigated the potential for direct assessment and monitoring of classroom daylight and lighting measurements. Combined with objective assessments of outdoor exposures and class time use, the classroom data could inform design and light exposure interventions to reduce the various health impacts of inadequate daylight exposure. The relevant environmental measure for myopia depends on the hypothesized mechanism, so the illuminance, spectral distribution, and temporal light modulation from the electric lighting was also assessed. Full article

In the manufacturing process of electrical devices, ensuring the cleanliness of technical surfaces, such as direct bonded copper substrates, is crucial. An in-line monitoring system for quality checking must provide sufficiently resolved lateral data in a short time. UV hyperspectral imaging is a promising in-line method for rapid, contactless, and large-scale detection of contamination; thus, UV hyperspectral imaging (225–400 nm) was utilized to characterize the cleanliness of direct bonded copper in a non-destructive way. In total, 11 levels of cleanliness were prepared, and a total of 44 samples were measured to develop multivariate models for characterizing and predicting the cleanliness levels. The setup included a pushbroom imager, a deuterium lamp, and a conveyor belt for laterally resolved measurements of copper surfaces. A principal component analysis (PCA) model effectively differentiated among the sample types based on the first two principal components with approximately 100.0% explained variance. A partial least squares regression (PLS-R) model to determine the optimal sonication time showed reliable performance, with R²_cv = 0.928 and RMSECV = 0.849. This model was able to predict the cleanliness of each pixel in a testing sample set, exemplifying a step in the manufacturing process of direct bonded copper substrates. Combined with multivariate data modeling, the in-line UV prototype system demonstrates a significant potential for further advancement towards its application in real-world, large-scale processes. Full article

Poly(3,4-ethylenedioxythiophene) (PEDOT) and PEDOT-functionalized carbon nanoparticles (f-CNPs) were synthesized by in situ chemical oxidative polymerization and pyrolysis methods. f-CNP-PEDOT nanocomposites were prepared by varying the concentration of PEDOT from 1 to 20% by weight (i.e., 1, 2.5, 5, 10, and 20 wt%). Several characterization techniques, such as field-emission scanning electron microscopy (FESEM), attenuated total reflectance-Fourier transform infrared (ATR-FTIR), X-ray diffraction (XRD), N₂ Brunauer–Emmett–Teller (BET) and Barrett–Joyner–Halenda (BJH) analyses, as well as cyclic voltammetry (CV), galvanostatic charge discharge (GCD), and electrochemical impedance spectroscopy (EIS), were applied to investigate the morphology, the crystalline structure, the N₂ adsorption/desorption capability, as well as the electrochemical properties of these new synthesized nanocomposite materials. FESEM analysis showed that these nanocomposites have defined porous structures, and BET surface area analysis showed that the standalone f-CNP exhibited the largest surface area of 801.6 m²/g, whereas the f-CNP-PEDOT with 20 wt% exhibited the smallest surface area of 116 m²/g. The BJH method showed that the nanocomposites were predominantly mesoporous. CV, GCD, and EIS measurements showed that f-CNP functionalized with 5 wt% PEDOT had a higher capacitive performance compared to the individual f-CNPs and PEDOT constituents, exhibiting an extraordinary specific capacitance of 258.7 F/g, at a current density of 0.25 A/g, due to the combined advantage of enhanced electrochemical activity induced by PEDOT doping, and highly developed porosity of f-CNPs. Symmetric aqueous supercapacitor devices were fabricated using the optimized f-CNP-PEDOT doped with 5 wt% of PEDOT as active material, exhibiting a high capacitance of 96.7 F/g at 1.4 V, holding practically their full charge, after 10,000 charge–discharge cycles at 2 A/g, thus providing the highest electrical electrodes performance. Hereafter, this work paves the way for the potential use of f-CNP-PEDOT nanocomposites in the development of high-energy-density supercapacitors. Full article

Although the introduction of drugs targeting calcitonin gene-related peptide (CGRP) revolutionized migraine treatment, still a substantial proportion of migraine patients do not respond satisfactorily to such a treatment, and new therapeutic targets are needed. Therefore, molecular studies on migraine pathogenesis are justified. Oxidative stress is implicated in migraine pathogenesis, as many migraine triggers are related to the production of reactive oxygen and nitrogen species (RONS). Migraine has been proposed as a superior mechanism of the brain to face oxidative stress resulting from energetic imbalance. However, the precise mechanism behind the link between migraine and oxidative stress is not known. Nociceptive primary afferent nerve fiber endings express ion channel receptors that change harmful stimuli into electric pain signals. Transient receptor potential cation channel subfamily A member 1 (TRPA1) is an ion channel that can be activated by oxidative stress products and stimulate the release of CGRP from nerve endings. It is a transmembrane protein with ankyrin repeats and conserved cysteines in its N-terminus embedded in the cytosol. TRPA1 may be a central element of the signaling pathway from oxidative stress and NO production to CGRP release, which may play a critical role in headache induction. In this narrative review, we present information on the role of oxidative stress in migraine pathogenesis and provide arguments that TRPA1 may be “a missing link” between oxidative stress and migraine and therefore a druggable target in this disease. Full article

The establishment of sustainable energy frameworks amidst global climate change and dwindling petroleum reserves has prompted a focus on energy transition, marking a shift in how energy is utilized within systems. Greece, historically reliant on lignite for electricity generation, faces the challenge of transitioning towards a low-carbon economy. This study explores the potential of creating a multipurpose entrepreneurship and culture center, the Mediterranean Center for Entrepreneurship and Culture (MCEC), in Megalopolis, Arcadia, Greece, as a strategic intervention for economic, social, and environmental restructuring. Drawing on best practices and comprehensive analyses of external factors, the study outlines the conceptualization and evaluation of the MCEC, considering economic feasibility, development scenarios, financial sustainability, and stakeholder engagement. The discussion highlights the anticipated benefits of the MCEC, including job creation, entrepreneurship promotion, and socio-cultural advancement, underscoring its potential to mitigate the impacts of lignite phase-out and foster sustainable regional development. Overall, the establishment of the MCEC is poised to yield positive socio-economic impacts, including employment growth, entrepreneurship promotion, infrastructure development, and cultural enrichment, contributing to the resilience and prosperity of the Megalopolis region and beyond. Full article

Campus buildings often face issues with high energy consumption, low efficiency, and significant carbon emissions, making the creation of a green, low-carbon campus urgent. Utilizing solar photovoltaics on rooftops can provide an effective power solution to address high energy consumption. This study focuses on a university campus, employing the DeST energy consumption simulation software to model the HVAC systems, electrical devices, and hot water loads of five typical buildings. It combines this with calculations of available rooftop areas to assess the potential for rooftop solar photovoltaics. The results confirm varying annual electricity consumption among the different buildings, which directly correlates with building size and operational schedules. Among the five building types, sports facilities and academic buildings have relatively high rooftop photovoltaic self-sufficiency rates, exceeding 60%, while the library has the lowest, under 20%. The entire university campus has an annual rooftop photovoltaic self-sufficiency rate of 35%, significantly addressing the issue of high energy consumption in university campuses. This research provides a theoretical basis for implementing rooftop photovoltaic systems to achieve campus energy savings. Full article

This work explores the transformative role of graphene in enhancing the performance of surface plasmon resonance (SPR)-based biosensors. The motivation for this review stems from the growing interest in the unique properties of graphene, such as high surface area, excellent electrical conductivity, and versatile functionalization capabilities, which offer significant potential to improve the sensitivity, specificity, and stability of SPR biosensors. This review systematically analyzes studies published between 2010 and 2023, covering key metrics of biosensor performance. The findings reveal that the integration of graphene consistently enhances sensitivity. Specificity, although less frequently reported numerically, showed promising results, with high specificity achieved at sub-nanomolar concentrations. Stability enhancements are also significant, attributed to the protective properties of graphene and improved biomolecule adsorption. Future research should focus on mechanistic insights, optimization of integration techniques, practical application testing, scalable fabrication methods, and comprehensive comparative studies. Our findings provide a foundation for future research, aiming to further optimize and harness the unique physical properties of graphene to meet the demands of sensitive, specific, stable, and rapid biosensing in various practical applications. Full article

Tracked vehicles are integral for maneuvering diverse terrains, with hybrid propulsion systems offering potential benefits in terms of fuel efficiency and performance. However, research in hybrid electric tracked vehicles remains limited, thus necessitating a comprehensive analysis to maximize their advantages. This study presents a numerical analysis focusing on optimizing hybridization in speed-coupled parallel hybrid electric powertrains for tracked vehicles. A dynamic programming algorithm and custom drive cycle are utilized to determine optimal hybridization factors and assess parameter sensitivities. The study reveals that a hybridization factor of 0.48 is optimal for speed-coupled parallel configurations. Furthermore, the sensitivity analysis underscores the substantial impact of factors such as the engine displacement and bore-to-stroke ratio on the fuel economy, with a 10% change in these parameters potentially influencing the fuel economy by up to 2%, thus emphasizing the importance of thorough consideration during powertrain sizing. Parallel hybrid configurations exhibit considerable potential for tracked vehicles, thus highlighting the viability of choosing them over series configurations. Full article