The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

The oil produced in the oil fields of the Republic of Kazakhstan contains a high percentage of sulfur. Synthesis and improvement of the properties of catalytic systems for the production of fuels with high octane number and low sulfur content is currently an urgent task for Kazakhstan. In this study, catalytic systems with a new composition based on zeolites with the addition of rare-earth metals (E) and phosphorus (P) have been prepared and tested in the process of the catalytic hydrotreating of straight-run gasoline and gasoline of catalytic cracking. In case of NiO-MoO3-E-P-HZSM-HY-Al2O3 catalyst, the octane rating of the gasoline after hydro-processing was increased to 88-90, which is much higher than for other catalysts. The octane number of straight-run gasoline up to 400°C is a maximum of 90 (Research Method) and 83.7 (Motor Method). At the same time, the sulfur content in the resulting gasoline decreases from 0.0088% to 0.0011%. In the case of catalytic cracking gasoline, the sulfur content is reduced from 0.0134% to 0.0012%. The smallest residual sulfur content in the final product, 0.0005% is revealed in case of catalyst CoO-WO3-E-P-HZSM-HY-Al2O3, and it is 2-4 times lower than for catalysts CoO-MoO3-E-P-HZSM-HY-Al2O3 and NiO-MoO3-E-P-HZSM-HY-Al2O3. These amounts of sulfur residue in raw materials is lower than that required by the Euro-5 Standard. The surface of the prepared catalysts was 211.0-274.0 m2/g, diameter of pores d ≈ 1.5-2.5 nm and d ≈ 7.0 nm. The total pore volume of the catalysts was not higher than 0.28-0.41 ml/g. The catalysts developed in this study can be used for hydrotreating raw materials and producing high-octane gasoline with a low sulfur content, corresponding in its characteristics to the Euro-5 Standard.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.