loading direction
Recently Published Documents

Abstract Cu with nanotwin (NT) possesses great electrical, mechanical, and thermal properties and has potential for electronic applications. Various studies have reported the effect of NT orientation on Cu mechanical properties. However, its effect on Cu stress-relaxation behavior has not been clarified, particularly in nano-scale. In this study, Cu nanopillars with various orientations were examined by a picoindenter under constant strain and observed by in-situ TEM. The angles between the twin plane and the loading direction in the examined nanopillars were 0°, 60°, to 90°, and a benchmark pillar of single-crystal Cu without NT was examined. The stress drops were respectively 10%, 80%, 4%, and 50%. Owing to the interaction by NT, the dislocation behavior in nanopillars was different from that in bulk or in thin film samples. Especially, the rapid slip path of dislocations to go to the free surface of the nanopillar induced a dislocation-free zone in the 0° nanopillar, which led to work-softening. On the contrary, a high dislocation density was observed in the 90° nanopillar, which was generated by dislocation interaction and obstruction of dislocation slip by twin planes, and it led to work-hardening. The findings reveal the NT orientation in Cu nanopillars affected stress relaxation significantly.

This paper addresses the damage behaviour of a nickel/yttria-stabilised zirconia (Ni-YSZ) anode, in order to understand microstructural degradation processes of Solid Oxide Fuel Cells (SOFCs) during long-term operation. Numerical investigations are carried out to analyse the failure mechanisms in detail. For this purpose, finite element (FE) models are generated from focused ion beam-scanning electron microscopy 3D image data, representing the anode microstructure with varying phase compositions. A brittle model and a ductile material model were assigned to the YSZ phase and the nickel phase, respectively. The porosity is found to affect the strength of the microstructure significantly, leading to low compressive strength results. A high Ni content generally increases the toughness of the overall structure. However, the orientation and the geometry of the nickel phase is essential. When the Ni phase is aligned parallel to the loading direction, a supporting effect on the microstructure is observed, resulting in a significant high toughness. On the contrary, a rapid failure of the sample occurs when the Ni phase is oriented perpendicular to the loading direction. Two main failure mechanisms are identified: (i) cracking at the Ni/YSZ interface and (ii) cracking of struts at the location of the smallest diameter.

AbstractInformation on the properties of nailed joints with decayed member is necessary to evaluate the remaining structural properties of timber constructions. In this study, loading tests were conducted on nailed joints parallel and perpendicular to the grain with decayed members, and the relationship between the decrease in shear properties and the loading direction to the grain was investigated. After the loading tests, the extent of decay of the specimens was evaluated by the penetration depth of Pilodyn and the decay depth, and these were compared with the shear properties of the nailed joints. The nailed joints with decay had a low load at the initial deformation, regardless of the loading direction to the grain. The initial stiffness, yield resistance, and maximum resistance of the nailed joints parallel to the grain were negatively correlated with the Pilodyn penetration depth, and those of the nailed joints perpendicular to the grain showed no significant correlation with the Pilodyn penetration depth at the 5% level. The initial stiffness, yield resistance, and maximum resistance of the nailed joints parallel to the grain tended to decrease with increasing decay depth, and those of the nailed joints perpendicular to the grain did not exhibit this tendency. The shear properties of the nailed joints significantly decreased at small decay depths.

Abstract This paper reports a structural modification of an auxetic metamaterial with a combination of representative re-entrant and chiral topologies, namely, a re-entrant chiral auxetic (RCA). The main driving force for the structural modification was to overcome the undesirable properties of the RCA metamaterial such as anisotropic mechanical response under uniaxial compression. Additively manufactured polyamide 12 specimens via Multi Jet Fusion (MJF) were quasi-statically compressed along the two in-plane directions. The experimental results confirmed that the modified structure was less sensitive to the loading direction and the deformation was more uniform. Moreover, similar energy absorptions were obtained when the modified metamaterial was crushed along the two in-plane directions. The energy absorptions were improved from 390 to 950 kJ/m³ and from 500 to 1000 kJ/m³ compared with the RCA when they were crushed along the X and Y directions, respectively. The absorbed energy per unit mass (SEA) also improved from 1.4 to 2.9 J/g and from 1.78 to 3.1 J/g compared with that of the RCA under the axial compression along the X and Y directions. Furthermore, parametric studies were performed and the effects of geometric parameters of the modified metamaterial were numerically investigated. Tuneable auxetic feature was obtained. The energy absorption and Poisson’s ratio of the modified metamaterial offer it a good alternative for a wide range of potential applications in the areas such as aerospace, automotive, and human protective equipment.

An experimental study is preformed to investigate the in-situ damage sensing capabilities of intra-ply hybrid carbon/glass laminate and epoxy composites under quasi-static interlaminar shear loading. A three-dimensional electrical sensory network is generated inside the composites through embedded carbon nanotubes (CNTs) in an epoxy matrix along with the carbon fibers in the intra-ply hybrid laminates. CNTs are dispersed in the epoxy matrix using a combination of ultrasonication and shear mixing techniques. Four circumferential ring probes are used to examine the electrical response under interlaminar shear load. The effect of four different intra-ply orientations (((0–90)C, where carbon fibers are oriented along the loading direction), ((0–90)G, where glass fibers are oriented along the loading direction), ((45/−45, where glass and carbon fibers are oriented at 45o/−45o and the laminates are repeated), and ((45/−45)A, where glass and carbon fibers are oriented at 45o/−45o and the laminates are alternated)) on the shear constitutive behavior and the damage detection are discussed. Intra-ply orientations of (45/−45) and (45/−45)A showed higher interlaminar shear strength and shear strain at break compared to (0/90)C and (0/90)G orientations. Out of all four orientations, (45/−45)A provided a better resolution of electrical response for damage sensing applications.

This paper proposes a design of novel composite materials inspired by the Peano curve and manufactured using PolyJet 3D printing technology with Agilus30 (flexible phase) and VeroMagentaV (rigid phase) materials. Mechanical properties were evaluated through tensile and compression tests. The general rule of mixture (ROM) for composites was employed to approximate the tensile properties of the hybrid materials and compare them to the experimental results. The effect of reinforcement alignments and different hierarchies are discussed. The results indicated that the 5% inclusion of the Peano reinforcement in tensile samples contributed to the improvement in the elastic modulus by up to 6 MPa, but provided no obvious enhancement in ultimate tensile strength. Additionally, compressive strengths between 2 MPa and 6 MPa were observed for compression cubes with first-order reinforcement, while lower values around 2 MPa were found for samples with second-order reinforcement. That is to say, the first-order reinforcement has been demonstrated more effectively than the second-order reinforcement, given the same reinforcement volume fraction of 10% in compression cubes. Different second-order designs exhibited slightly different mechanical properties based on the ratio of reinforcement parallel to the loading direction.