bending test
Recently Published Documents

Nowadays, the application of the engineered cementitious composites(ECC) is expected to highly develop. Due to the lack of access to oiled- polyvinyl alcohol (PVA) fibers in many parts of the world, the implementation of the ECC has contained many difficulties. In this study, to increase the mechanical properties of ECC with the use of un-oiled PVA fibers, the polymers of styrene butadiene rubber (SBR), and ethylene vinyl acetate (EVA) were taken into account to resolve the abovementioned issue. Herein, also in order to enhance the tensile and flexural properties of ECC, the cement was replaced by polymers. Accordingly, a total of 7 mix designs were planned to conduct the proposed tests. The compressive strength, uniaxial tensile strength, and three-point bending tests were performed on the ECC at their 28-day age with consideration of the freeze and thaw cycle. The results of this research illustrated that the use of polymers can enhance the tensile and flexural properties of the ECC with un-oiled PVA fibers. The tensile strain in this study increased by more than 3% after the application of the polymers. Furthermore, the compressive strength increased by more than 47 MPa, and the deflection at the mid-span reached more than 9 mm in the bending test. However, the results showed that the use of polymers was effective on the freeze and thaw cycle and almost preserved the mechanical properties of the ECC. SBR latex has higher compatibility with the ECC in comparison with EVA powder.

AbstractStrain energy decomposition methods in phase field fracture models separate strain energy that contributes to fracture from that which does not. However, various decomposition methods have been proposed in the literature, and it can be difficult to determine an appropriate method for a given problem. The goal of this work is to facilitate the choice of strain decomposition method by assessing the performance of three existing methods (spectral decomposition of the stress or the strain and deviatoric decomposition of the strain) and one new method (deviatoric decomposition of the stress) with several benchmark problems. In each benchmark problem, we compare the performance of the four methods using both qualitative and quantitative metrics. In the first benchmark, we compare the predicted mechanical behavior of cracked material. We then use four quasi-static benchmark cases: a single edge notched tension test, a single edge notched shear test, a three-point bending test, and a L-shaped panel test. Finally, we use two dynamic benchmark cases: a dynamic tensile fracture test and a dynamic shear fracture test. All four methods perform well in tension, the two spectral methods perform better in compression and with mixed mode (though the stress spectral method performs the best), and all the methods show minor issues in at least one of the shear cases. In general, whether the strain or the stress is decomposed does not have a significant impact on the predicted behavior.

An experimental study was carried out to evaluate the ductility of reinforced concrete beams longitudinally reinforced with hybrid FRP-Steel bars. The specimens were fourteen reinforced concrete beams with and without hybrid reinforcement. The test variables were bars position, the ratio of longitudinal reinforcement, and the type of FRP bars. The beams were loaded up to failure using a four-point bending test. The performance of the tested beams was observed using the load-deflection curve obtained from the test. Numerical analysis using the fiber element model was used to examine the growth of neutral axis depth due to the effect of test variables. The neutral axis curves were then used to further estimate the neutral axis angle and neutral axis displacement index. The test results show that the position of the reinforcement greatly influences the flexural behavior of the beam with hybrid reinforcement. It was observed from the test that the flexural capacity of beams with hybrid reinforcement is 4% to 50% higher than that of the beams with conventional steel bars depending on bars position and the ratio of longitudinal reinforcement. The ductility decreases as the hybrid reinforcement ratio (Af/As) increases. This study also showed that a numerical model developed can predict the flexural behavior of beams with hybrid reinforcement with reasonable accuracy.

The paper presents the experimental investigations on the flexural behaviour of geopolymer concrete beams reinforced with Basalt Fibre Reinforced Polymer (BFRP)/Glass Fibre Reinforced Polymer (GFRP) rebars and the effect of inclusion of the new adhesively bonded BFRP/GFRP stirrups. M30 grade geopolymer and conventional concrete beams with the dimension of 100 × 160 × 1700 mm were cast to investigae the flexural behaviour of BFRP/GFRP and steel bars. This study also examined the mode of failure, deflection behaviour, curvature moment capacity, crack width, pattern, propagation, strains and average crack width of the BFRP/GFRP bars with stirrups in the geopolymer concretes using a four-point static bending test. The results were compared to that of conventional steel-reinforced concrete, and it was found that the Basalt and Glass reinforced polymer beams demonstrated premature failure and sudden shear failure. Further, the FRP bars exhibited higher mid-span deflection, crack width and crack propagation than steel bars. Crack spacing of the FRP bars decreased with an increase in the number of cracks. The correlation between the load and the deflection behaviour of the beams was determined using statistical analysis of multi variables regression.

The fatigue damage behavior of bone has attracted significant attention in both the mechanical and orthopedic fields. However, due to the complex and hierarchical structure of bone, describing the damage process quantitively or qualitatively is still a significant challenge for researchers in this area. In this study, a nonlinear bi-modulus gradient model was proposed to quantify the neutral axis skewing under fatigue load in a four-point bending test. The digital image correlation technique was used to analyze the tensile and compressive strains during the fatigue process. The results showed that the compressive strain demonstrated an obvious two-stage ascending behavior, whereas the tensile strain revealed a slow upward progression during the fatigue process. Subsequently, a theoretical model was proposed to describe the degradation process of the elastic modulus and the movement of the neutral axis. The changes in the bone properties were determined using the FEM method based on the newly developed model. The results obtained from two different methods exhibited a good degree of consistency. The results obtained in this study are of help in terms of effectively exploring the damage evolution of the bone materials.

The good mechanical performance of bamboo, coupled with its sustainability, has boosted the idea to use it as a structural material. In some areas of the world it is regularly used in constructions but there are still countries in which there is a lack of knowledge of the mechanical properties of the locally-grown bamboo, which limits the spread of this material. Bamboo is optimized to resist to flexural actions with its peculiar micro structure along the thickness in which the amount of fibers intensifies towards the outer layer and the inner part is composed mostly of parenchyma. The flexural strength depends on the amount of fibers, whereas the flexural ductility is correlated to the parenchyma content. This study focuses on the flexural strength and ductility of six different species of untreated bamboo grown in Italy. A four-point bending test was carried out on bamboo strips in two different loading configurations relating to its microstructure. Deformation data are acquired from two strain gauges in the upper and lower part of the bamboo beam. Difference in shape and size of Italian bamboo species compared to the ones traditionally used results in added complexity when performing the tests. Such difficulties and the found solutions are also described in this work. The main goal is to reveal the flexural behavior of Italian bamboo as a functionally graded material and to expand the knowledge of European bamboo species toward its use as a structural material not only as culm but also as laminated material.

Fibre-reinforced concrete (FRC) is widely employed in the construction industry, with assorted fibre types being used for different applications. Typically, steel fibres give additional tensile strength to the mixture, while flexible fibres may be used in large sections, such as floor slabs, to control crack width and to improve the handling ability of precast sections. For many reasons, including durability concerns, environmental impact, thermal performance, etc, alternatives to the currently available fibres are being sought. This study examines the potential of using basalt fibres, a mineral and natural material, as reinforcement of concrete sections in comparison to steel fibres and plain concrete mix. Mixes were tested containing 0.5% and 1.0% of basalt fibres measuring 25mm length, 0.5% of the same material with 48mm length and steel fibres measuring 50mm by 0.05%, 0.1%, 0.15% and 0.2% of the concrete volume. For the mechanical performance analysis, the 3-point bending test was led and the fracture energy, Young’s modulus and tensile strength in different moments of the tests were calculated. When compared to the control mixtures and the steel-fibre-reinforced concrete, the mixes containing basalt had a reduction in their elastic modulus, representing a decrease in the concrete brittleness. At the same time, the fracture energy of the mixtures was significantly increased with the basalt fibres in both lengths. Finally, the flexural strength was also higher for the natural fibre reinforced concrete than for the plain concrete and comparable to the results obtained with the addition of steel fibres by 0.15%.

This research work aimed to study the usage of Bamboo strips as shear reinforcement in reinforced concrete (RC) beams. Four beams were considered in this study. The flexural reinforcement for all beams was the same. As for shear reinforcement, one beam was reinforced with conventional shear reinforcement with spacing (s=180 mm), while the other three beams were reinforced with bamboo strips with three different spacings (s=180 mm, s= 90 mm, and s=60 mm). The beams were subjected to a four-point bending test to plot the load-deflection curve for each beam. Results showed that the beam reinforced with bamboo strips spaced at 180 mm has 30% higher shear capacity than the beam with conventional shear reinforcement at the same spacing. Also, as the spacing of bamboo strips decreased, the shear capacity of beams increased nonlinearly.

The main objective of the study was to determine the effect of impregnation of the paper core with acetylated starch on the mechanical properties and absorbed energy in the three-point bending test of wood-based honeycomb panels under varying temperatures and relative air humidity conditions. Nearly six hundred beams in various combinations, three types of facings, three core cells geometries, and two paper thicknesses were tested. The experiment results and their statistical analysis prove a significant relationship between the impregnation of paper with modified starch and mechanical properties. The most effective in absorbing energy, the honeycomb panels, consisted of a core with a wall thickness of 0.25 mm and a particleboard facing.