aluminum silicate
Recently Published Documents

Abstract In view of the low-frequency noise problem in urban substation, the sound absorption (SA) properties of aluminum silicate fibers (ASF) with different materials, unit weight, plate thickness and cavity thickness were tested in this paper. It was found that the high-purity ASF with larger unit weight, plate thickness and cavity thickness had larger low-frequency SA coefficient, which provided technical support for the development of new low-frequency noise reduction materials for substation.

The lithium bromide absorption refrigeration system with medium temperature solar collector as driving heat source was built, and the refrigeration performance of the system was tested and analyzed. The medium-temperature solar collector adopts all-glass vacuum solar collector tube with heat-conducting oil as medium, and the inside of the vacuum tube is composed of heat-conducting medium flow channel on the sunny side and aluminum silicate insulation cotton on the backlight side. Through test and analysis, the medium temperature solar collector of the system can provide stable heat source, and the maximum temperature of solar heating can reach above 150°C in sunny weather and about 80°C in cloudy days. The generator driving heat of the system is stable and efficient. The driving heat of lithium bromide absorption refrigerator is higher than 200 MJ/h, and can reach 300 MJ/h in some periods. The COP of the system can be kept above 0.6 during stable operation, but when the driving temperature of the generator is higher than 80°C, the COP of the system basically does not increase with the increase of the driving temperature.

In this paper, the system of natural mineral alkali fluxes used in typical mineral industry technologies was analyzed. The main objective was to lower the melting temperature of the flux systems. The research has shown that the best melting parameters in the Ca–Mg– (Li,Na,K) system were characterized by the composition: A-eutectic 20% and wollastonite 80%, and it was reached at temperature 1140 °C; in addition, this set had the widest melting interval. Selected thermal parameters of mineral flux systems were also calculated. The technological properties of mineral composites such as shrinkage and brightness were also analyzed.

The existence of a specific gallery type of zeolite framework is confirmed. It has been found that similar to HEU-type, STI-type framework can be represented as a layered structure in which two impermeable to water molecules and exchange cations aluminum-silicate layers, separated by diortho-groups, confined gallery-type of porous free space, which is available for extra-framework components migration in all directions in the plane of the interlayer.

Lignocellulose (LCE) was ultrasonically treated and intercalated into magnesium aluminum silicate (MOT) clay to prepare a nano-lignocellulose magnesium aluminum silicate polymer gel (nano-LCE-MOT) for the removal of Zn (II) from aqueous solution. The product was characterised using nitrogen adsorption/desorption isotherm measurements, Fourier-transform infrared spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectroscopy. The conditions for the adsorption of Zn (II) on nano-LCE-MOT were screened, and adsorption kinetics and isotherm model analysis were carried out to explore the adsorption mechanism and achieve the optimal adsorption of Zn (II). Optimal adsorption was achieved at an initial Zn (II) concentration of 800 mg/L at 60 °C in 160 min at a pH of 4.52. The adsorption kinetics were explored using a pseudo-second-order model, with the isotherm adsorption equilibrium found to conform to the Langmuir model. The maximum adsorption capacity of the nano-LCE-MOT polymer gel toward Zn (II) is 513.48 mg/g. The materials with adsorbed Zn (II) were desorbed using different media, with HCl found to be the most ideal medium to desorb Zn (II). The optimal desorption of Zn (II) was achieved in 0.08 mol/L HCl solution at 65 °C in 60 min. Under these conditions, Zn (II) was almost completely desorbed from the adsorbents, with the adsorption effect after cycling being slightly different from that of the initial adsorption.