SI FM 2e SM Chap06

Chapter 6 Momentum Analysis of Flow Systems
Solutions Manual for
Fluid Mechanics: Fundamentals and Applications SI Edition

Second Edition Yunus A. engel & John M. Cimbala McGraw-Hill, 2010
CHAPTER 6 MOMENTUM ANALYSIS OF FLOW SYSTEMS
PROPRIETARY AND CONFIDENTIAL This Manual is the proprietary property of The McGraw-Hill Companies, Inc. (McGraw-Hill) and protected by copyright and other state and federal laws. By opening and using this Manual the user agrees to the following restrictions, and if the recipient does not agree to these restrictions, the Manual should be promptly returned unopened to McGraw-Hill: This Manual is being provided only to authorized professors and instructors for use in preparing for the classes using the affiliated textbook. No other use or distribution of this Manual is permitted. This Manual may not be sold and may not be distributed to or used by any student or other third party. No part of this Manual may be reproduced, displayed or distributed in any form or by any means, electronic or otherwise, without the prior written permission of McGraw-Hill.
6-1
PROPRIETARY MATERIAL. 2010 The McGraw-Hill Companies, Inc. Limited distribution permitted only to teachers and educators for course preparation. If you are a student using this Manual, you are using it without permission.
Chapter 6 Momentum Analysis of Flow Systems Newtons Laws and Conservation of Momentum
6-1C Solution
We are to discuss the conservation of momentum principle.
Analysis The conservation of momentum principle is expressed as the momentum of a system remains constant when the net force acting on it is zero, and thus the momentum of such systems is conserved. The momentum of a body remains constant if the net force acting on it is zero. Discussion Momentum is not conserved in general, because when we apply a force, the momentum changes.
6-2C Solution
We are to express Newtons three laws.
Analysis Newtons first law states that a body at rest remains at rest, and a body in motion remains in motion at the same velocity in a straight path when the net force acting on it is zero. Therefore, a body tends to preserve its state of inertia. Newtons second law states that the acceleration of a body is proportional to the net force acting on it and is inversely proportional to its mass. Newtons third law states that when a body exerts a force on a second body, the second body exerts an equal and opposite force on the first. Discussion As we shall see in later chapters, the differential equation of fluid motion is based on Newtons second law.
6-3C Solution
We are to discuss Newtons second law for rotating bodies.
Analysis Newtons second law of motion, also called the angular momentum equation, is expressed as the rate of change of the angular momentum of a body is equal to the net torque acting it. For a non-rigid body with zero net torque, the angular momentum remains constant, but the angular velocity changes in accordance with I = constant where I is the moment of inertia of the body. Discussion Angular momentum is analogous to linear momentum in this way: Linear momentum does not change unless a force acts on it. Angular momentum does not change unless a torque acts on it.
6-2
Chapter 6 Momentum Analysis of Flow Systems Linear Momentum Equation
6-4C Solution
We are to describe and discuss body forces and surface forces.
Analysis The forces acting on the control volume consist of body forces that act throughout the entire body of the control volume (such as gravity, electric, and magnetic forces) and surface forces that act on the control surface (such as the pressure forces and reaction forces at points of contact). The net force acting on a control volume is the sum of all body and surface forces. Fluid weight is a body force, and pressure is a surface force (acting per unit area). Discussion In a general fluid flow, the flow is influenced by both body and surface forces.
6-5C Solution
We are to discuss surface forces in a control volume analysis.
Analysis All surface forces arise as the control volume is isolated from its surroundings for analysis, and the effect of any detached object is accounted for by a force at that location. We can minimize the number of surface forces exposed by choosing the control volume (wisely) such that the forces that we are not interested in remain internal, and thus they do not complicate the analysis. A well-chosen control volume exposes only the forces that are to be determined (such as reaction forces) and a minimum number of other forces. Discussion There are many choices of control volume for a given problem. Although there are not really wrong and right choices of control volume, there certainly are wise and unwise choices of control volume.
6-6C Solution
We are to discuss the importance of the RTT, and its relationship to the linear momentum equation.
Analysis The relationship between the time rates of change of an extensive property for a system and for a control volume is expressed by the Reynolds transport theorem (RTT), which provides the link between the system and r r control volume concepts. The linear momentum equation is obtained by setting b = V and thus B = mV in the Reynolds transport theorem. Discussion Newtons second law applies directly to a system of fixed mass, but we use the RTT to transform from the system formulation to the control volume formulation.
6-7C Solution Analysis
We are to discuss the momentum flux correction factor, and its significance.
The momentum-flux correction factor enables us to express the momentum flux in terms of the mass flow r r r r & V (V n )dAc = mV avg . The value of is unity for uniform flow, such as a jet flow, rate and mean flow velocity as
Ac
nearly unity for fully developed turbulent pipe flow (between 1.01 and 1.04), but about 1.3 for fully developed laminar pipe flow. So it is significant and should be considered in laminar flow; it is often ignored in turbulent flow. Discussion Even though is nearly unity for many turbulent flows, it is wise not to ignore it.
6-3
Chapter 6 Momentum Analysis of Flow Systems 6-8C Solution Analysis We are to discuss the momentum equation for steady one-D flow with no external forces.
The momentum equation for steady one-dimensional flow for the case of no external forces is r r r & & F = 0 = mV mV
out in
where the left hand side is the net force acting on the control volume (which is zero here), the first term on the right hand side is the incoming momentum flux, and the second term on the right is the outgoing momentum flux by mass.
Discussion This is a special simplified case of the more general momentum equation, since there are no forces. In this case, we can say that momentum is conserved.
6-9C Solution
We are to explain why we can usually work with gage pressure rather than absolute pressure.
Analysis In the application of the momentum equation, we can disregard the atmospheric pressure and work with gage pressures only since the atmospheric pressure acts in all directions, and its effect cancels out in every direction. Discussion In some applications, it is better to use absolute pressure everywhere, but for most practical engineering problems, it is simpler to use gage pressure everywhere, with no loss of accuracy.
6-10C Solution
We are to discuss if the upper limit of a rockets velocity is limited to V, its discharge velocity.
Analysis No, V is not the upper limit to the rockets ultimate velocity. Without friction the rocket velocity will continue to increase (i.e., it will continue to accelerate) as more gas is expelled out the nozzle. Discussion This is a simple application of Newtons second law. As long as there is a force acting on the rocket, it will continue to accelerate, regardless of how that force is generated.
6-11C Solution
We are to describe how a helicopter can hover.
Analysis A helicopter hovers because the strong downdraft of air, caused by the overhead propeller blades, manifests a momentum in the air stream. This momentum must be countered by the helicopter lift force. Discussion
In essence, the helicopter stays aloft by pushing down on the air with a net force equal to its weight.
6-12C Solution
We are to discuss the power required for a helicopter to hover at various altitudes.
Analysis Since the air density decreases, it requires more energy for a helicopter to hover at higher altitudes, because more air must be forced into the downdraft by the helicopter blades to provide the same lift force. Therefore, it takes more power for a helicopter to hover on the top of a high mountain than it does at sea level. Discussion This is consistent with the limiting case if there were no air, the helicopter would not be able to hover at all. There would be no air to push down.
6-4
Chapter 6 Momentum Analysis of Flow Systems 6-13C Solution

We are to discuss helicopter performance in summer versus winter.
Analysis In winter, the air is generally colder, and thus denser. Therefore, less air must be driven by the blades to provide the same helicopter lift, requiring less power. Less energy is required in the winter. Discussion However, it is also harder for the blades to move through the denser cold air, so there is more torque required of the engine in cold weather.
6-14C Solution
We are to discuss if the force required to hold a plate stationary doubles when the jet velocity doubles.
Analysis No, the force will not double. In fact, the force required to hold the plate against the horizontal water stream will increase by a factor of 4 when the velocity is doubled since
& F = mV = ( AV )V = AV 2
and thus the force is proportional to the square of the velocity.
Discussion You can think of it this way: Since momentum flux is mass flow rate times velocity, a doubling of the velocity doubles both the mass flow rate and the velocity, increasing the momentum flux by a factor of four.
6-15C Solution
We are to compare the reaction force on two fire hoses.
Analysis The fireman who holds the hose backwards so that the water makes a U-turn before being discharged will experience a greater reaction force. This is because of the vector nature of the momentum equation. Specifically, the inflow and outflow terms end up with the same sign (they add together) for the case with the U-turn, whereas they have opposite signs (one partially cancels out the other) for the case without the U-turn. Discussion
Direction is not an issue with the conservation of mass or energy equations, since they are scalar equations.
6-16C Solution
We are to discuss the acceleration of a cart hit by a water jet.
Analysis The acceleration is not constant since the force is not constant. The impulse force exerted by the water & on the plate is F = mV = ( AV )V = AV 2 , where V is the relative velocity between the water and the plate, which is moving. The magnitude of the plate acceleration is thus a = F/m. But as the plate begins to move, V decreases, so the acceleration must also decrease. Discussion
It is the relative velocity of the water jet on the cart that contributes to the carts acceleration.
6-17C Solution
We are to discuss the maximum possible velocity of a cart hit by a water jet.
Analysis The maximum possible velocity for the plate is the velocity of the water jet. As long as the plate is moving slower than the jet, the water exerts a force on the plate, which causes it to accelerate, until terminal jet velocity is reached. Discussion
Once the relative velocity is zero, the jet supplies no force to the cart, and thus it cannot accelerate further.
6-5
Chapter 6 Momentum Analysis of Flow Systems 6-18 Solution A water jet of velocity V impinges on a plate moving toward the water jet with velocity V. The force required to move the plate towards the jet is to be determined in terms of F acting on the stationary plate. Assumptions 1 The flow is steady and incompressible. 2 The plate is vertical and the jet is normal to plate. 3 The pressure on both sides of the plate is atmospheric pressure (and thus its effect cancels out). 4 Fiction during motion is negligible. 5 There is no acceleration of the plate. 6 The water splashes off the sides of the plate in a plane normal to the jet. 6 Jet flow is nearly uniform and thus the effect of the momentum-flux correction factor is negligible, 1. Analysis We take the plate as the control volume. The relative velocity between the plate and the jet is V when the plate is stationary, and 1.5V when the plate is moving with a velocity V towards the plate. Then the momentum equation for steady one-dimensional flow in the horizontal direction reduces to 1/2V r r r & & & & F= mV mV FR = mi Vi FR = mi Vi V
out
in
Stationary plate: ( Vi = V and

Moving plate: ( Vi = 1.5V and
& m i = AVi = AV ) FR = AV 2 = F
& m i = AVi = A(1.5V ) )
Waterjet
FR = A(1.5V ) 2 = 2.25 AV 2 = 2.25 F Therefore, the force required to hold the plate stationary against the oncoming water jet becomes 2.25 times greater when the jet velocity becomes 1.5 times greater. Note that when the plate is stationary, V is also the jet velocity. But if the plate moves toward the stream Discussion with velocity V, then the relative velocity is 1.5V, and the amount of mass striking the plate (and falling off its sides) per unit time also increases by 50%.
6-6
Chapter 6 Momentum Analysis of Flow Systems 6-19 Solution A 90 elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place are to be determined. Assumptions 1 The flow is steady and incompressible. 2 Frictional effects are negligible in the calculation of the pressure drop (so that the Bernoulli equation can be used). 3 The weight of the elbow and the water in it is negligible. 4 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. 5 The momentum-flux correction factor for each inlet and outlet is given to be = 1.03. Properties
We take the density of water to be 1000 kg/m3.
Analysis (a) We take the elbow as the control volume, and designate the entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction) and the vertical & & & coordinate by z. The continuity equation for this one-inlet one-outlet steady flow system is m1 = m 2 = m = 30 kg/s. Noting & = AV , the mean inlet and outlet velocities of water are that m & & 30 kg/s m m = = = 3.820 m/s V1 = V2 = V = 2 A (D / 4) (1000 kg/m 3 )[ (0.1 m) 2 / 4]
Noting that V1 = V2 and P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is expressed as
P V12 P V2 1 + + z1 = 2 + 2 + z2 P P2 = g ( z2 z1 ) P , gage = g ( z2 z1 ) 1 1 g 2 g g 2 g
Substituting,
1 kN P1, gage = (1000 kg/m 3 )(9.81 m/s 2 )(0.40 m) 1000 kg m/s 2 = 3.924 kN/m 2 3.92 kPa
(b) The momentum equation for steady one-dimensional flow is
& & F = mV mV .
out in
We let the x- and z-
components of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along the x and y axes become
& & FRx + P1,gage A1 = 0 m(+V1 ) = mV & & FRz = m( +V 2 ) = mV Solving for FRx and FRz, and substituting the given values,
& FRx = mV P1, gage A1 1N = 1.03(30 kg/s)(3.820 m/s) 1 kg m/s 2 = 148.9 N (3924 N/m 2 )[ (0.1 m) 2 / 4]
= 118.0 N
z x FRz
Water 30 kg/s
2
40 cm
FRx 1
1N & FRy = mV = 1.03(30 kg/s)(3.820 m/s) 1 kg m/s 2
and
2 2 FR = FRx + FRy = (148.9) 2 + (118.0) 2 = 190 N,
= tan -1
FRy FRx
= tan -1
118.0 = 38.4 = 142 148.9
Discussion Note that the magnitude of the anchoring force is 190 N, and its line of action makes 142 from the positive x direction. Also, a negative value for FRx indicates the assumed direction is wrong, and should be reversed.
6-7
Chapter 6 Momentum Analysis of Flow Systems 6-20 Solution A 180 elbow forces the flow to make a U-turn and discharges it to the atmosphere at a specified rate. The gage pressure at the inlet of the elbow and the anchoring force needed to hold the elbow in place are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Frictional effects are negligible in the calculation of the pressure drop (so that the Bernoulli equation can be used). 3 The weight of the elbow and the water in it is negligible. 4 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. 5 The momentum-flux correction factor for each inlet and outlet is given to be = 1.03. Properties
Analysis (a) We take the elbow as the control volume, and designate the entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction) and the vertical & & & coordinate by z. The continuity equation for this one-inlet one-outlet steady flow system is m1 = m 2 = m = 30 kg/s. Noting & = AV , the mean inlet and outlet velocities of water are that m & & 30 kg/s m m = = = 3.820 m/s V1 = V2 = V = 2 A (D / 4) (1000 kg/m 3 )[ (0.1 m) 2 / 4]
Noting that V1 = V2 and P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is expressed as
P V12 P V2 1 + + z1 = 2 + 2 + z2 P P2 = g ( z2 z1 ) P , gage = g ( z2 z1 ) 1 1 g 2 g g 2 g
Substituting,
1 kN P1, gage = (1000 kg/m 3 )(9.81 m/s 2 )(0.80 m) 1000 kg m/s 2 = 7.848 kN/m 2 7.85 kPa
& & F = mV mV .
out in
We let the x- and z-
components of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along the x and z axes become
& & & FRx + P1,gage A1 = m(V 2 ) m(+V1 ) = 2mV
FRz = 0 Solving for FRx and substituting the given values,

& FRx = 2mV P1, gage A1 1N = 2 1.03(30 kg/s)(3.820 m/s) 1 kg m/s 2 = 298 N (7848 N/m 2 )[ (0.1 m) 2 / 4]
2 z x FRz
Water 30 kg/s 40 cm
FRx 1
and FR = FRx = 298 N since the y-component of the anchoring force is zero. Therefore, the anchoring force has a magnitude of 298 N and it acts in the negative x direction.
Discussion
Note that a negative value for FRx indicates the assumed direction is wrong, and should be reversed.
6-8
Chapter 6 Momentum Analysis of Flow Systems 6-21 Solution A reducing elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The anchoring force needed to hold the elbow in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Frictional effects are negligible in the calculation of the pressure drop (so that the Bernoulli equation can be used). 3 The weight of the elbow and the water in it is considered. 4 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. 5 The momentum-flux correction factor for each inlet and outlet is given to be = 1.03. Properties Analysis
We take the density of water to be 1000 kg/m3. The weight of the elbow and the water in it is
25 cm2
W = mg = (50 kg)(9.81 m/s 2 ) = 490.5 N = 0.4905 kN
45
We take the elbow as the control volume, and designate the FRz entrance by 1 and the outlet by 2. We also designate the FRx horizontal coordinate by x (with the direction of flow as being the positive direction) and the vertical coordinate by z. The 150 cm2 Water continuity equation for this one-inlet one-outlet steady flow 30 kg/s W & & & & system is m1 = m 2 = m = 30 kg/s. Noting that m = AV , the 1 inlet and outlet velocities of water are & 30 kg/s m V1 = = = 2.0 m/s A1 (1000 kg/m 3 )(0.0150 m 2 ) & 30 kg/s m V2 = = = 12 m/s A2 (1000 kg/m 3 )(0.0025 m 2 ) Taking the center of the inlet cross section as the reference level (z1 = 0) and noting that P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is expressed as
V 2 V12 V 2 V12 P V12 P V2 1 + + z1 = 2 + 2 + z2 P P2 = g 2 + z2 z1 P , gage = g 2 1 1 2 g + z2 2g g 2 g g 2 g
Substituting,
(12 m/s) 2 ( 2 m/s) 2 1 kN = 73.9 kN/m 2 = 73.9 kPa P , gage = (1000 kg/m3 )(9.81 m/s 2 ) + 0.4 1 2 1000 kg m/s 2 2(9.81 m/s ) r r r & & F= mV mV . We let the x- and z- components The momentum equation for steady one-dimensional flow is
out
in
of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along the x and z axes become
& & & FRx + P1,gage A1 = mV 2 cos mV1 and FRz W = mV 2 sin
Solving for FRx and FRz, and substituting the given values,
1 kN & FRx = m (V2 cos V )1 P , gage A1 = 1.03( 30 kg/s)[(12cos45-2) m/s] 73.9 kN/m 2 )( 0.0150 m 2 ) 1 2 ( 1000 kg m/s = 0.908 kN 1 kN & FRz = mV 2 sin + W = 1.03(30 kg/s)(12sin45 m/s) 1000 kg m/s 2 + 0.4905 kN = 0.753 kN FRz 0.753 2 2 FR = FRx + FRz = (0.908) 2 + (0.753) 2 = 1.18 kN, = tan -1 = tan -1 = 39.7 FRx 0.908
Note that the magnitude of the anchoring force is 1.18 kN, and its line of action makes 39.7 from +x Discussion direction. Negative value for FRx indicates the assumed direction is wrong.
6-9
Chapter 6 Momentum Analysis of Flow Systems 6-22 Solution A reducing elbow deflects water upwards and discharges it to the atmosphere at a specified rate. The anchoring force needed to hold the elbow in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Frictional effects are negligible in the calculation of the pressure drop (so that the Bernoulli equation can be used). 3 The weight of the elbow and the water in it is considered. 4 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. 5 The momentum-flux correction factor for each inlet and outlet is given to be = 1.03. Properties Analysis
We take the density of water to be 1000 kg/m3. The weight of the elbow and the water in it is
W = mg = (50 kg)(9.81 m/s 2 ) = 490.5 N = 0.4905 kN
110
2
25 cm2
We take the elbow as the control volume, and designate the entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction) and FRz 150 m2 the vertical coordinate by z. The continuity equation for this one-inlet FRx & & & one-outlet steady flow system is m1 = m 2 = m = 30 kg/s. Noting that & Water 1 m = AV , the inlet and outlet velocities of water are W 30 kg/s & 30 kg/s m V1 = = = 2.0 m/s A1 (1000 kg/m 3 )(0.0150 m 2 ) & 30 kg/s m V2 = = = 12 m/s A2 (1000 kg/m 3 )(0.0025 m 2 ) Taking the center of the inlet cross section as the reference level (z1 = 0) and noting that P2 = Patm, the Bernoulli equation for a streamline going through the center of the reducing elbow is expressed as
V 2 V12 V22 V12 P V12 P V2 1 + + z1 = 2 + 2 + z2 P P2 = g 2 1 1 2 g + z2 z1 P , gage = g 2 g + z2 g 2 g g 2 g
(12 m/s)2 (2 m/s)2 1 kN = 73.9 kN/m 2 = 73.9 kPa or, P , gage = (1000 kg/m3 )(9.81 m/s 2 ) + 0.4 1 2 1000 kg m/s 2 2(9.81 m/s ) r r r &V & The momentum equation for steady one-dimensional flow is F= m mV . We let the x- and y- components
out
in
of the anchoring force of the elbow be FRx and FRz, and assume them to be in the positive directions. We also use gage pressures to avoid dealing with the atmospheric pressure which acts on all surfaces. Then the momentum equations along the x and z axes become
& & FRx + P1,gage A1 = mV 2 cos mV1
and
& FRy W = mV 2 sin
Solving for FRx and FRz, and substituting the given values, & FRx = m(V 2 cos V1 ) P1, gage A1
1 kN = 1.03(30 kg/s)[(12cos110 - 2) m/s] 1000 kg m/s 2 FRz
(73.9 kN/m 2 )(0.0150 m 2 ) = 1.297 kN 1 kN + 0.4905 kN = 0.8389 kN & = mV 2 sin + W = 1.03(30 kg/s)(12sin110 m/s) 1000 kg m/s 2
FRz 0.8389 = tan -1 = 32.9 1.297 FRx
2 2 FR = FRx + FRz = (1.297) 2 + 0.8389 2 = 1.54 kN
and
= tan -1
Note that the magnitude of the anchoring force is 1.54 kN, and its line of action makes 32.9 from +x Discussion direction. Negative value for FRx indicates assumed direction is wrong, and should be reversed.
6-10
Chapter 6 Momentum Analysis of Flow Systems 6-23 Solution Water accelerated by a nozzle strikes the back surface of a cart moving horizontally at a constant velocity. The braking force and the power wasted by the brakes are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters off the sides of the plate in all directions in the plane of the back surface. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric pressure which is disregarded since it acts on all surfaces. 4 Friction during motion is negligible. 5 There is no acceleration of the cart. 7 The motions of the water jet and the cart are horizontal. 6 Jet flow is nearly uniform and thus the effect of the momentum-flux correction factor is negligible, 1. Analysis We take the cart as the control volume, and the direction of flow as the positive direction of x axis. The relative velocity between the cart and the jet is
Vr = V jet Vcart = 20 5 = 15 m/s
5 m/s 20 m/s Waterjet
Therefore, we can view the cart as being stationary and the jet moving with a velocity of 15 m/s. Noting that water leaves the nozzle at 20 m/s and the corresponding mass flow rate relative to nozzle exit is 30 kg/s, the mass flow rate of water striking the cart corresponding to a water jet velocity of 10 m/s relative to the cart is
& mr = Vr 15 m/s & m jet = (30 kg/s) = 22.5 kg/s V jet 20 m/s
FRx
The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to r r r & & & & F= mV mV FRx = m iVi Fbrake = m r V r
out
in
We note that the brake force acts in the opposite direction to flow, and we should not forget the negative sign for forces and velocities in the negative x-direction. Substituting the given values, 1N & Fbrake = m r Vr = (22.5 kg/s)(+15 m/s) 1 kg m/s 2 = 337.5 N 338 N
The negative sign indicates that the braking force acts in the opposite direction to motion, as expected. Noting that work is force times distance and the distance traveled by the cart per unit time is the cart velocity, the power wasted by the brakes is
1W & W = FbrakeVcart = (337.5 N)(5 m/s) = 1688 W 1.69 W 1 N m/s
Discussion Note that the power wasted is equivalent to the maximum power that can be generated as the cart velocity is maintained constant.
6-24 Solution Water accelerated by a nozzle strikes the back surface of a cart moving horizontally. The acceleration of the cart if the brakes fail is to be determined.
5 m/s
Analysis The braking force was determined in previous problem to be 337.5 N. When the brakes fail, this force will propel the cart forward, and the acceleration will be
a= F 337.5 N 1 kg m/s 2 = mcart 400 kg 1N = 0.844 m/s 2
20 m/s 400 kg Waterjet
FRx
Discussion This is the acceleration at the moment the brakes fail. The acceleration will decrease as the relative velocity between the water jet and the cart (and thus the force) decreases.
6-11
Chapter 6 Momentum Analysis of Flow Systems 6-25 Solution A water jet hits a stationary splitter, such that half of the flow is diverted upward at 45, and the other half is directed down. The force required to hold the splitter in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure of the water jet before and after the split is the atmospheric pressure which is disregarded since it acts on all surfaces. 3 The gravitational effects are disregarded. 4 Jet flow is nearly uniform and thus the effect of the momentum-flux correction factor is negligible, 1. Properties Analysis
We take the density of water to be 1000 kg/m3. The mass flow rate of water jet is
5.5 m/s
2.8 m3/s
FRz
45 45
FRx
& & m = V = (1000 kg/m 3 )(2.8 m 3 /s) = 2800 kg/s We take the splitting section of water jet, including the splitter as the control volume, and designate the entrance by 1 and the outlet of either arm by 2 (both arms have the same velocity and mass flow rate). We also designate the horizontal coordinate by x with the direction of flow as being the positive direction and the vertical coordinate by z. r r r & & The momentum equation for steady one-dimensional flow is F= mV mV . We let the x- and y-
out
in
components of the anchoring force of the splitter be FRx and FRz, and assume them to be in the positive directions. Noting & & that V2 = V1 = V and m 2 = 1 m , the momentum equations along the x and z axes become 2 & & & FRx = 2( 1 m)V 2 cos mV1 = mV (cos 1) 2 & & FRz = 1 m(+V 2 sin ) + 1 m(V 2 sin ) 0 = 0 2 2 Substituting the given values,
1N FRx = (2800 kg/s)(5.5 m/s)(cos45 1) 1 kg m/s = 4511 N FRz = 0 The negative value for FRx indicates the assumed direction is wrong, and should be reversed. Therefore, a force of 4511 N must be applied to the splitter in the opposite direction to flow to hold it in place. No holding force is necessary in the vertical direction. This can also be concluded from the symmetry.
Discussion In reality, the gravitational effects will cause the upper stream to slow down and the lower stream to speed up after the split. But for short distances, these effects are indeed negligible.
6-12
Chapter 6 Momentum Analysis of Flow Systems 6-26

Solution The previous problem is reconsidered. The effect of splitter angle on the force exerted on the splitter as the half splitter angle varies from 0 to 180 in increments of 10 is to be investigated.
Analysis
The EES Equations window is printed below, followed by the tabulated and plotted results.
theta=45 [degrees] rho=1000 [kg/m^3] V_dot=2.8 [m^3/s] V=5.5 [m/s] m_dot=rho*V_dot F_R=-m_dot*V*(cos(theta)-1)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
FR, N 0 234 928.7 2063 3603 5501 7700 10133 12726 15400 18074 20667 23100 25299 27197 28737 29871 30566 30800
35000 30000 25000
FR [N]
20000 15000 10000 5000 0 0
20
40
60
80
100
120
140
160
180
[degrees]
Discussion
The force rises from zero at = 0o to a maximum at = 180o, as expected, but the relationship is not linear.
6-13
Chapter 6 Momentum Analysis of Flow Systems 6-27 Solution A horizontal water jet impinges normally upon a vertical plate which is held on a frictionless track and is initially stationary. The initial acceleration of the plate, the time it takes to reach a certain velocity, and the velocity at a given time are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water always splatters in the plane of the retreating plate. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric pressure which is disregarded since it acts on all surfaces. 4 The track is nearly frictionless, and thus friction during motion is negligible. 5 The motions of the water jet and the cart are horizontal. 6 The velocity of the jet relative to the plate remains constant, Vr = Vjet = V. 7 Jet flow is nearly uniform and thus the effect of the momentum-flux correction factor is negligible, 1. Properties
(a) We take the vertical plate on the frictionless track as the control volume, and the direction of flow as the Analysis positive direction of x axis. The mass flow rate of water in the jet is & m = VA = (1000 kg/m 3 )(18 m/s)[ (0.05 m) 2 / 4] = 35.34 kg/s The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to r r r & & & & F= mV mV FRx = miVi FRx = mV
out
in
where FRx is the reaction force required to hold the plate in place. When the plate is released, an equal and opposite impulse force acts on the plate, which is determined to
1N & Fplate = FRx = mV = (35.34 kg/s)(18 m/s) 1 kg m/s 2 = 636 N
Then the initial acceleration of the plate becomes

a= Fplate m plate 636 N 1 kg m/s 2 = 1000 kg 1 N = 0.636 m/s 2
18 m/s 1000 kg Waterjet Frictionless track
This acceleration will remain constant during motion since the force acting on the plate remains constant.
FRx
(b) Noting that a = dV/dt = V/t since the acceleration a is constant, the time it takes for the plate to reach a velocity of 9 m/s is t = V plate a = (9 0) m/s 0.636 m/s 2 = 14.2 s
(c) Noting that a = dV/dt and thus dV = adt and that the acceleration a is constant, the plate velocity in 20 s becomes Vplate = V0, plate + at = 0 + (0.636 m/s 2 )(20 s) = 12.7 m/s
Discussion The assumption that the relative velocity between the water jet and the plate remains constant is valid only for the initial moments of motion when the plate velocity is low unless the water jet is moving with the plate at the same velocity as the plate.
6-14
Chapter 6 Momentum Analysis of Flow Systems 6-28 A horizontal water jet strikes a curved plate, which deflects the water back to its original direction. The Solution force required to hold the plate against the water stream is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3 Friction between the plate and the surface it is on is negligible (or the friction force can be included in the required force to hold the plate). 4 There is no splashing of water or the deformation of the jet, and the reversed jet leaves horizontally at the same velocity and flow rate. 5 Jet flow is nearly uniform and thus the momentum-flux correction factor is nearly unity, 1. Properties
2
37 m/s
Waterjet
FRx
1
37 m/s
10 cm
Analysis We take the plate together with the curved water jet as the control volume, and designate the jet inlet by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of incoming flow as being the & & & positive direction). The continuity equation for this one-inlet one-outlet steady flow system is m1 = m 2 = m where
& m = VA = V [D 2 / 4] = (1000 kg/m 3 )(37 m/s)[ (0.10 m) 2 / 4] = 290.6 kg/s r r r & & F= mV mV . Letting the reaction force to hold The momentum equation for steady one-dimensional flow is
out
in
the plate be FRx and assuming it to be in the positive direction, the momentum equation along the x axis becomes & & & FRx = m( V 2 ) m(+V1 ) = 2mV Substituting,
1N FRx = 2( 290.6 kg/s)(37 m/s) 1 kg m/s = 21,504 N -21,500 N Therefore, a force of 21,500 N must be applied on the plate in the negative x direction to hold it in place.
Discussion Note that a negative value for FRx indicates the assumed direction is wrong (as expected), and should be reversed. Also, there is no need for an analysis in the vertical direction since the fluid streams are horizontal.
6-15
Chapter 6 Momentum Analysis of Flow Systems 6-29 Solution Firemen are holding a nozzle at the end of a hose while trying to extinguish a fire. The average water outlet velocity and the resistance force required of the firemen to hold the nozzle are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure of the water jet is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3 Gravitational effects and vertical forces are disregarded since the horizontal resistance force is to be determined. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
(a) We take the nozzle and the horizontal Analysis portion of the hose as the system such that water enters the control volume vertically and outlets horizontally (this way the pressure force and the momentum flux at the inlet are in the vertical direction, with no contribution to the force balance in the horizontal direction), and designate the entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). The average outlet velocity and the mass flow rate of water are determined from V& V& 5 m 3 /min V= = = = 1768 m/min = 29.5 m/s A D 2 / 4 (0.06 m) 2 / 4
& m = V& = (1000 kg/m 3 )(5 m 3 /min) = 5000 kg/min = 83.3 kg/s
FRz FRx
5 m3/min
& & F = mV mV . We let horizontal force

out in
applied by the firemen to the nozzle to hold it be FRx, and assume it to be in the positive x direction. Then the momentum equation along the x direction gives 1N & & FRx = mVe 0 = mV = ( 83.3 kg/s ) (29.5 m/s) = 2457 N 2460 N 2 1kg m/s Therefore, the firemen must be able to resist a force of 2460 N to hold the nozzle in place. The force of 2460 N is equivalent to the weight of about 250 kg. That is, holding the nozzle requires the Discussion strength of holding a weight of 250 kg, which cannot be done by a single person. This demonstrates why several firemen are used to hold a hose with a high flow rate.
6-16
Chapter 6 Momentum Analysis of Flow Systems 6-30 Solution A horizontal jet of water with a given velocity strikes a flat plate that is moving in the same direction at a specified velocity. The force that the water stream exerts against the plate is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters in all directions in the plane of the plate. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric pressure, which is disregarded since it acts on all surfaces. 4 The vertical forces and momentum fluxes are not considered since they have no effect on the horizontal force exerted on the plate. 5 The velocity of the plate, and the velocity of the water jet relative to the plate, are constant. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
40 m/s 10 m/s
Analysis We take the plate as the control volume, and the flow direction as the positive direction of x axis. The relative velocity between the plate and the jet is
Vr = V jet Vplate = 40 10 = 30 m/s
FRx
5 cm Waterjet
Therefore, we can view the plate as being stationary and the jet to be moving with a velocity of 30 m/s. The mass flow rate of water relative to the plate [i.e., the flow rate at which water strikes the plate] is D 2 (0.05 m) 2 & m r = Vr A = Vr = (1000 kg/m 3 )(30 m/s) = 58.90 kg/s 4 4 The momentum equation for steady one-dimensional flow is
& & F = mV mV . We let the horizontal reaction
out in
force applied to the plate in the negative x direction to counteract the impulse of the water jet be FRx. Then the momentum equation along the x direction gives 1N = 1767 N & & FRx = 0 mVi FRx = m rVr = (58.90 kg/s)(30 m/s) 1kg m/s 2 Therefore, the water jet applies a force of 1767 N on the plate in the direction of motion, and an equal and opposite force must be applied on the plate if its velocity is to remain constant.
Discussion Note that we used the relative velocity in the determination of the mass flow rate of water in the momentum analysis since water will enter the control volume at this rate. (In the limiting case of the plate and the water jet moving at the same velocity, the mass flow rate of water relative to the plate will be zero since no water will be able to strike the plate).
6-17
Chapter 6 Momentum Analysis of Flow Systems 6-31

Solution The previous problem is reconsidered. The effect of the plate velocity on the force exerted on the plate as the plate velocity varies from 0 to 30 m/s in increments of 3 m/s is to be investigated.
Analysis
rho=1000 "kg/m3" D=0.05 "m" V_jet=30 "m/s" Ac=pi*D^2/4 V_r=V_jet-V_plate m_dot=rho*Ac*V_r F_R=m_dot*V_r "N"
18 00 16 00 14 00 12 00
Vplate, m/s 0 3 6 9 12 15 18 21 24 27 30
Vr, m/s 30 27 24 21 18 15 12 9 6 3 0
FR, N 1767 1431 1131 866 636 442 283 159 70.7 17.7 0
F R, N
10 00 800 600 400 200 0 0 5 10 15 20 Vplate, m /s 25 30
Discussion When the plate velocity reaches 30 m/s, there is no relative motion between the jet and the plate; hence, there can be no force acting.
6-18
Chapter 6 Momentum Analysis of Flow Systems 6-32 Solution A fan moves air at sea level at a specified rate. The force required to hold the fan and the minimum power input required for the fan are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 Standard atmospheric conditions exist so that the pressure at sea level is 1 atm. 3 Air leaves the fan at a uniform velocity at atmospheric pressure. 4 Air approaches the fan through a large area at atmospheric pressure with negligible velocity. 5 The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of air (no conversion to thermal energy through frictional effects). 6 Wind flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties The gas constant of air is R = 0.287 kPam3/kgK. The standard atmospheric pressure at sea level is 1 atm = 101.3 kPa. Analysis (a) We take the control volume to be a horizontal hyperbolic cylinder bounded by streamlines on the sides with air entering through the large cross-section (section 1) and the fan located at the narrow cross-section at the end (section 2), and let its centerline be the x axis. The density, mass flow rate, and discharge velocity of air are P 101.3 kPa = = = 1.205 kg/m 3 RT (0.287 kPa m 3 /kg K)(293 K)
& & m = V = (1.205 kg/m 3 )(0.95 m 3 /s) = 1.144 kg/s
0.95 m3/s Fan 1 2 61 cm
V2 =
& & 0.95 m 3 /s V V = = = 3.251 m/s 2 A2 D2 / 4 (0.61 m) 2 / 4
The momentum equation for steady one-dimensional flow is
& & F = mV mV . Letting the reaction force to hold

out in
the fan be FRx and assuming it to be in the positive x (i.e., the flow) direction, the momentum equation along the x axis becomes
1N & & FRx = m(V2 ) 0 = mV = (1.144 kg/s)(3.251 m/s) 1 kg m/s 2 = 3.72 N Therefore, a force of 3.72 N must be applied (through friction at the base, for example) to prevent the fan from moving in the horizontal direction under the influence of this force. (b) Noting that P1 = P2 = Patm and V1 0, the energy equation for the selected control volume reduces to
P V2 P V2 & & & & & m 1 + 1 + gz1 + W pump, u = m 2 + 2 + gz 2 + W turbine + E mech,loss 2 2 Substituting,
V & & Wfan, u = m 2 2
1 W V2 (3.251 m/s) 2 1N & & Wfan,u = m 2 = (1.144 kg/s) 1 kg m/s 2 1 N m/s = 6.05 W 2 2 Therefore, a useful mechanical power of 6.05 W must be supplied to air. This is the minimum required power input required for the fan.
The actual power input to the fan will be larger than 6.05 W because of the fans inefficiency in converting Discussion mechanical power to kinetic energy.
6-19
Chapter 6 Momentum Analysis of Flow Systems 6-33 Solution A helicopter hovers at sea level while being loaded. The volumetric air flow rate and the required power input during unloaded hover, and the rpm and the required power input during loaded hover are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 Air leaves the blades at a uniform velocity at atmospheric pressure. 3 Air approaches the blades from the top through a large area at atmospheric pressure with negligible velocity. 4 The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of air (no conversion to thermal energy through frictional effects). 5 The change in air pressure with elevation is negligible because of the low density of air. 6 There is no acceleration of the helicopter, and thus the lift generated is equal to the total weight. 7 Air flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
The density of air is given to be 1.18 kg/m3.
Analysis (a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the bottom (section 2), and let its centerline be the z axis with upwards being the positive direction. r r r & & The momentum equation for steady one-dimensional flow is F= mV mV . Noting that the only
out
in
force acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation along the z axis gives 1 W & & W = m(V 2 ) 0 W = mV 2 = ( AV 2 )V 2 = AV 22 V2 = 18 m A where A is the blade span area, A = D 2 / 4 = (18 m) 2 / 4 = 254.5 m 2 2 Then the discharge velocity, volume flow rate, and the mass flow rate of air in the unloaded mode become
V2,unloaded =
munloaded g = A
(10,000 kg)(9.81 m/s 2 ) (1.18 kg/m 3 )(254.5 m 2 )

3 3
= 18.07 m/s
Sea level Load 14,000 kg
V&unloaded = AV2,unloaded = (254.5 m 2 )(18.07 m/s) = 4600 m 3 /s

& m unloaded = V&unloaded = (1.18 kg/m )(4600 m /s) = 5428 kg/s
Noting that P1 = P2 = Patm, V1 0, the elevation effects are negligible, and the frictional effects are disregarded, the energy equation for the selected control volume reduces to P V2 P V2 V2 & & & & & & & m 1 + 1 + gz1 + W pump, u = m 2 + 2 + gz 2 + W turbine + E mech,loss Wfan, u = m 2 2 2 2 Substituting, V2 1 kW (18.07 m/s) 2 1 kN & & Wunloaded fan,u = m 2 = (5428 kg/s) 1000 kg m/s 2 1 kN m/s = 886.2 kW 886 kW 2 2 unloaded (b) We now repeat the calculations for the loaded helicopter, whose mass is 10,000+14,000 = 24,000 kg:
V2,loaded =
mloaded g = A
(24,000 kg)(9.81 m/s 2 ) (1.18 kg/m 3 )(254.5 m 2 )
= 28.00 m/s
& mloaded = V&loaded = AV 2, loaded = (1.18 kg/m 3 )(254.5 m 2 )(28.00 m/s) = 8409 kg/s
V2 1 kW (28.00 m/s) 2 1 kN & & Wloaded fan,u = m 2 = (8409 kg/s) 1000 kg m/s 2 1 kN m/s = 3296 kW 3300 kW 2 2 loaded Noting that the average flow velocity is proportional to the overhead blade rotational velocity, the rpm of the loaded helicopter blades becomes V2,loaded V2,loaded & n 28.00 & & & = loaded nloaded = n unloaded = (400 rpm) = 620 rpm V2 = kn & V2,unloaded 18.07 V2,unloaded n unloaded
The actual power input to the helicopter blades will be considerably larger than the calculated power input Discussion because of the fans inefficiency in converting mechanical power to kinetic energy. 6-20
Chapter 6 Momentum Analysis of Flow Systems 6-34 Solution A helicopter hovers on top of a high mountain where the air density is considerably lower than that at sea level. The blade rotational velocity to hover at the higher altitude and the percent increase in the required power input to hover at high altitude relative to that at sea level are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 The air leaves the blades at a uniform velocity at atmospheric pressure. 3 Air approaches the blades from the top through a large area at atmospheric pressure with negligible velocity. 4 The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of air. 5 The change in air pressure with elevation while hovering at a given location is negligible because of the low density of air. 6 There is no acceleration of the helicopter, and thus the lift generated is equal to the total weight. 7 Air flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
The density of air is given to be 1.18 kg/m3 at sea level, and 0.928 kg/m3 on top of the mountain.
(a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides Analysis with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the bottom (section 2), and let its centerline be the z axis with upwards being the positive direction. r r r & & The momentum equation for steady one-dimensional flow is F= mV mV . Noting that the only
out
in
force acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation along the z axis gives W & & W = m(V 2 ) 0 W = mV 2 = ( AV 2 )V 2 = AV 22 V2 = A where A is the blade span area. Then for a given weight W, the ratio of discharge velocities becomes
V2,mountain V2,sea
W / mountain A W / sea A
sea mountain
1.18 kg/m3 = 1.1276 0.928 kg/m3
Noting that the average flow velocity is proportional to the overhead blade rotational velocity, the rpm of the helicopter blades on top of the mountain becomes
& n = kV2
& nmountain V2,mountain = & nsea V2,sea
& nmountain =
V2,mountain V2,sea
& nsea = 1.1276(400 rpm) = 451.052 rpm 451 rpm
Noting that P1 = P2 = Patm, V1 0, the elevation effect are negligible, and the frictional effects are disregarded, the energy equation for the selected control volume reduces to
P V2 P V2 & & & & & m 1 + 1 + gz1 + W pump, u = m 2 + 2 + gz 2 + W turbine + E mech,loss 2 2

or
V2 V2 V3 & & Wfan,u = m 2 = AV2 2 = A 2 = 2 2 2
1 2
V & & Wfan, u = m 2 2
1
18 m
W = A
1 2
W A
1.5
W 1.5 2 A
Then the ratio of the required power input on top of the mountain to that at sea level becomes
& Wmountain fan,u 0.5W 1.5 / mountain A = & Wsea fan,u 0.5W 1.5 / sea A
sea mountain
1.18 kg/m 3 0.928 kg/m 3
= 1.128
Sea level Load 14,000 kg
Therefore, the required power input will increase by approximately 12.8% on top of the mountain relative to the sea level.
Discussion Note that both the rpm and the required power input to the helicopter are inversely proportional to the square root of air density. Therefore, more power is required at higher elevations for the helicopter to operate because air is less dense, and more air must be forced by the blades into the downdraft.
6-21
Chapter 6 Momentum Analysis of Flow Systems 6-35 Solution The flow rate in a channel is controlled by a sluice gate by raising or lowering a vertical plate. A relation for the force acting on a sluice gate of width w for steady and uniform flow is to be developed.
Assumptions 1 The flow is steady, incompressible, frictionless, and uniform (and thus the Bernoulli equation is applicable.) 2 Wall shear forces at channel walls are negligible. 3 The channel is exposed to the atmosphere, and thus the pressure at free surfaces is the atmospheric pressure. 4 The flow is horizontal. 5 Water flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Analysis We take point 1 at the free surface of the upstream flow before the gate and point 2 at the free surface of the downstream flow after the gate. We also take the bottom surface of the channel as the reference level so that the elevations of points 1 and 2 are y1 and y2, respectively. The application of the Bernoulli equation between points 1 and 2 gives
P1 V12 P V2 + + y1 = 2 + 2 + y 2 g 2 g g 2 g V 22 V12 = 2 g( y1 y 2 ) (1)
The flow is assumed to be incompressible and thus the density is constant. Then the conservation of mass relation for this single stream steady flow device can be expressed as
V&1 = V&2 = V&
A1V1 = A2V 2 = V&
V1 =
V&
A1
V&
wy1
and
V2 =
V&
A2
V&
wy 2
(2)
Substituting into Eq. (1),

V& wy 2
2 2 V& 2 g ( y1 y 2 ) & wy = 2 g ( y1 y 2 ) V = w 1 / y 2 1 / y 2 1 2 1
2 g ( y1 y 2 ) V& = wy 2 2 2 1 y 2 / y1
(3)
Substituting Eq. (3) into Eqs. (2) gives the following relations for velocities,
V1 = y2 y1 2 g ( y1 y 2 ) 1
2 y2
2 y1
and
V2 =
2 g ( y1 y 2 )
2 2 1 y 2 / y1
(4)
We choose the control volume as the water body surrounded by the vertical cross-sections of the upstream and downstream flows, free surfaces of water, the inner surface of the sluice gate, and the bottom surface of the channel. The momentum r r r & & equation for steady one-dimensional flow is F= mV mV . The force acting on the sluice gate FRx is
out
in
horizontal since the wall shear at the surfaces is negligible, and it is equal and opposite to the force applied on water by the sluice gate. Noting that the pressure force acting on a vertical surface is equal to the product of the pressure at the centroid of the surface and the surface area, the momentum equation along the x direction gives y y & & & FRx + P1 A1 P2 A2 = mV 2 mV1 FRx + g 1 ( wy1 ) g 2 ( wy 2 ) = m(V 2 V1 ) 2 2 Rearranging, the force acting on the sluice gate is determined to be
& FRx = m(V1 V 2 ) + w 2 2 g ( y 1 y 2 ) 2
1 FRx V1
y1
(5)
where V1 and V2 are given in Eq. (4). Thus,
y & FRx = m 2 y1
2 g ( y1 y2 ) 2 g ( y1 y2 ) w 2 + g ( y12 y2 ) 2 2 2 2 1 y2 / y1 1 y2 / y1 2
y2 2 g ( y1 y2 ) w 2 1 + g ( y12 y2 ) . 2 y1 1 y2 / y12 2
Sluice gate y2
V2
& or, simplifying, FRx = m

Discussion
Note that for y1 >> y2, Eq. (3) simplifies to V& = y 2 w 2gy1 or V 2 = 2gy1 which is the Torricelli equation
for frictionless flow from a tank through a hole a distance y1 below the free surface.
6-22
Chapter 6 Momentum Analysis of Flow Systems 6-36 Solution Water enters a centrifugal pump axially at a specified rate and velocity, and leaves in the normal direction along the pump casing. The force acting on the shaft in the axial direction is to be determined.
Properties
We take the density of water to be 1000 kg/m3. z x
0.12 m3/s 7 m/s
Assumptions 1 The flow is steady and incompressible. 2 The forces acting on the piping system in the horizontal direction are negligible. 3 The atmospheric pressure is disregarded since it acts on all surfaces.
Analysis We take the pump as the control volume, and the inlet direction of flow as the positive direction of x axis. The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to r r r & & & & FRx = mVi FRx = mVi = V&Vi F= mV mV
mV
FRx
out
in
Note that the reaction force acts in the opposite direction to flow, and we should not forget the negative sign for forces and velocities in the negative x-direction. Substituting the given values,
1N Fbrake = (1000 kg/m 3 )(0.12 m 3 /s)(7 m/s) 1 kg m/s 2
= 840 N
Discussion To find the total force acting on the shaft, we also need to do a force balance for the vertical direction, and find the vertical component of the reaction force.
6-23
Chapter 6 Momentum Analysis of Flow Systems 6-37 Solution A curved duct deflects a fluid. The horizontal force exerted on V1 CV the duct by the fluid is to be determined. 1 1 P1,gage Assumptions 1 The flow is steady and incompressible. 2 The momentumA1 flux correction factor for each inlet and outlet is given to account for frictional effects and the non-uniformity of the inlet and outlet velocity profiles. Fx, duct on fluid
Properties The density of the liquid is = 998.2 kg/m3. Viscosity does not enter our analysis. Analysis (a) We take the fluid within the duct as the control volume (see sketch), and designate the inlet by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). Conservation of mass for this one-inlet one-outlet & & & steady flow system is m = m1 = m2 . The mass flow rate is
& m = V1 A1 = V2 A2 , and the average speed at the outlet is thus V2 =
V2
P2,gage
& V A V A m = 1 1 = 1 1 . Since A1 = A2 in this problem, A2 A2 A2
V2= V1. The momentum equation for steady flow in the x-direction is
x on CV
& & = mu mu , where u is the

out in
horizontal velocity component: u1 = V1 and u2 = -V1. The total force on the control volume consists of pressure forces at the inlet and outlet plus the total of all forces (including pressure and viscous forces) acting on the control volume by the duct walls. Calling this force Fx, duct on fluid, and assuming it to be in the positive x-direction, we write & & P A1 + P2,gage A2 + Fx , duct on fluid = m 2 ( V1 ) m1V1 1,gage Note that we must be careful with the signs for forces (including pressure forces) and velocities. Solving for Fx, duct on fluid, & and plugging in m = V1 A1 , we get
2 Fx , duct on fluid = ( P 1,gage + P 2,gage ) A V1 A ( 1 + 2 ) 1 1
Finally, the force exerted by the fluid on the duct is the negative of this, i.e.,
2 Fx = Fx , fluid on duct = Fx , duct on fluid = ( P 1,gage + P 2,gage ) A + V1 A ( 1 + 2 ) 1 1
(b)
We verify our expression by plugging in the given values:
N N kg m N Fx = 78470 2 + 65230 2 ( 0.025 m 2 ) + 998.2 3 10 ( 0.025 m 2 ) (1.01 + 1.03) 2 m m m s kg m/s = 8683.3 N 8680 N
where we give the final answer to three significant digits in keeping with our convention.
Discussion The direction agrees with our intuition. The fluid is trying to push the duct to the right. A negative value for Fx, fluid on duct indicates that the initially assumed direction was incorrect, but did not hinder our solution.
6-24
Chapter 6 Momentum Analysis of Flow Systems 6-38 Solution A curved duct deflects a fluid. The horizontal force exerted on V1 CV the duct by the fluid is to be determined. 1 1 P1,gage Assumptions 1 The flow is steady and incompressible. 2 The momentumA1 flux correction factor for each inlet and outlet is given to account for frictional effects and the non-uniformity of the inlet and outlet velocity profiles.
Properties The density of the liquid is = 998.2 kg/m3. Viscosity does not enter our analysis. Analysis (a) We take the fluid within the duct as the control volume (see sketch), and designate the inlet by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). Conservation of mass for this one-inlet one-outlet steady flow & & & & system is m = m1 = m2 . The mass flow rate is m = V1 A1 = V2 A2 , and the
average speed at the outlet is thus V2 =
Fx, duct on fluid
V2
A2 2
& V A V A m = 1 1 = 1 1 . The momentum A2 A2 A2
P2,gage
equation for steady flow in the x-direction is
x on CV
& & = mu mu , where u is the horizontal velocity

out in
component: u1 = V1 and u2 = -V2. The total force on the control volume consists of pressure forces at the inlet and outlet plus the total of all forces (including pressure and viscous forces) acting on the control volume by the duct walls. Calling this force Fx, duct on fluid, and assuming it to be in the positive x-direction, we write & & P A1 + P2,gage A2 + Fx , duct on fluid = m 2 ( V2 ) m1V1 1,gage Note that we must be careful with the signs for forces (including pressure forces) and velocities. Solving for Fx, duct on fluid, VA & and plugging in m = V1 A1 and V2 = 1 1 , we get A2
A Fx , duct on fluid = P A1 P2,gage A2 V12 A1 1 + 2 1 1,gage A2 Finally, the force exerted by the fluid on the duct is the negative of this, i.e.,
A Fx = Fx , fluid on duct = Fx , duct on fluid = P A1 + P2,gage A2 + V12 A1 1 + 2 1 1,gage A2

(b) We verify our expression by plugging in the given values:
N N Fx = 88340 2 ( 0.025 m 2 ) + 67480 2 ( 0.015 m 2 ) m m kg m 0.025 m 2 N + 998.2 3 20 ( 0.025 m 2 ) 1.02 + 1.04 2 2 m s 0.015 m kg m/s = 30704.5 N 30,700 N to the right
where we give the final answer to three significant digits in keeping with our convention.
2
6-25
Chapter 6 Momentum Analysis of Flow Systems 6-39 Solution We are to calculate the force exerted by water on a curved duct for a range of inlet velocities, and compare to the force computed with CFD.
Assumptions 1 The flow is steady and incompressible. 2 The momentum-flux correction factor for each inlet and outlet is given to account for frictional effects and the non-uniformity of the inlet and outlet velocity profiles. Properties Analysis
The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis. (a) We apply the equation derived in the previous problem for the case in which A1 = A2,
2 Fx = ( P 1,gage + P 2,gage ) A + V1 A ( 1 + 2 ) 1 1
For example, at an inlet velocity of 10 m/s, FlowLab gives P1,gage = 14245.3 Pa and P2,gage = 5582.7222 Pa, and we get 2 N N kg m N Fx = 14245.3 2 + 5582.7222 2 ( 0.025 m 2 ) + 998.2 3 10 ( 0.025 m 2 ) (1.005 + 1.03) 2 m m m s kg m/s
= 5574.04 N 5,570 N
where we have rounded to three significant digits. We repeat the calculations for a range of inlet velocities, and show the results in the table below. Note that pressures P1 and P2 are outputs from the CFD code, and are gage pressures.
The agreement between our conservation law analysis and the CFD calculations is very good the error is less than about 1.5% for all cases.
Discussion The conservation laws are fundamental, so it is no surprise that they work well. The main source of error here is the momentum flux correction factor at the inlet and outlet, which we have guessed. By basic principles, if we know the pressure, area, velocity profile (or the average velocity and momentum flux correction factor) at all inlets and outlets of a control volume, we should be able to predict the net force quite accurately, as illustrated here.
6-26
Chapter 6 Momentum Analysis of Flow Systems 6-40 Solution We are to calculate the force exerted by water on a curved duct for a range of area ratios, and compare to the force computed with CFD.
The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis.
A A2 2 2 Fx = P A1 + P2,gage A2 + V12 A1 1 + 2 1 = A1 P + V1 A1 1 + 1,gage 1,gage + P 2,gage A2 A1 A2 A1

For example, at an inlet velocity of 1.0 m/s and an area ratio of 1.2, FlowLab gives P1,gage = 78.8447 Pa and P2,gage = 114.410 Pa, and we get 2 N N kg m 1.03 N Fx = ( 0.025 m 2 ) 78.8447 2 + 114.410 2 (1.2 ) + 998.2 3 1.0 ( 0.025 m 2 ) 1.01 + m m m s 1.2 kg m/s 2
= 52.0277 N 52.0 N
(a) We apply the equation derived in the previous problem, for the case in which A1 A2.
where we have rounded to three significant digits. We repeat the calculations for a range of area ratios, and show the results in the table below. Note that pressures P1 and P2 are outputs from the CFD code, and are gage pressures.
The agreement between our conservation law analysis and the CFD calculations is excellent the error is less than 1.5% for all cases.
Discussion A main source of error here is the momentum flux correction factor at the inlet and outlet, which we have guessed. However, it turns out that the pressure forces dominate, and the terms in the equation with do not contribute much to the force even poor guesses for 1 and 2 would not change the answers much. The force drops as area ratio increases, and this agrees with our intuition, but it increases slowly at high area ratios.
6-27
Chapter 6 Momentum Analysis of Flow Systems 6-41 Solution The curved duct analysis of the previous problem is to be examined more closely. Namely, we are to explain how the pressure can actually rise from inlet to outlet.
The simple answer is that when the area ratio is greater than 1, the duct acts as a diffuser. From the Analysis Bernoulli approximation, we know that as the velocity decreases along the duct (since area increases), the pressure increases. Irreversibilities act counter to this, and cause the pressure to drop along the duct. For large enough area ratio, the diffuser effect wins. In this problem, the pressure changes from decreasing to increasing at an area ratio of around 1.3.
Discussion The curvature does not affect the fact that the duct acts like a diffuser the area still increases. In fact, some diffusers are curved, e.g., centrifugal pumps and the draft tubes of hydroelectric turbines, as discussed in the turbomachinery chapter.
6-28
Chapter 6 Momentum Analysis of Flow Systems 6-42 Solution A curved duct deflects a fluid. The horizontal force exerted on V1 the duct by the fluid is to be determined. CV 1 1 Assumptions 1 The flow is steady and incompressible. 2 The momentumP1,gage flux correction factor for each inlet and outlet is given to account for frictional A1 effects and the non-uniformity of the inlet and outlet velocity profiles. Fx, duct on fluid Properties The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis.
(a) We take the fluid within the duct as the control volume (see Analysis sketch), and designate the inlet by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). Conservation of mass for this one-inlet one-outlet steady flow & & & & system is m = m1 = m2 . The mass flow rate is m = V1 A1 = V2 A2 , and the average speed at the outlet is thus V2 =
2 V2 , 2, P2, gage A2
& V A V A m = 1 1 = 1 1 . The momentum A2 A2 A2
equation for steady flow in the x-direction is
x on CV
& & = mu mu , where u is the horizontal velocity component.

out in
The total force on the control volume consists of pressure forces at the inlet and outlet plus the total of all forces (including pressure and viscous forces) acting on the control volume by the duct walls. Calling this force Fx, duct on fluid, and assuming it to be in the positive x-direction, we write & & P A1 P2,gage A2 cos + Fx , duct on fluid = m 2V2 cos m1V1 1,gage Note that we must be careful with the signs for forces (including pressure forces) and velocities. Solving for Fx, duct on fluid, & and plugging in m = V1 A1 , we get
Fx , duct on fluid = P A1 + P2,gage A2 cos + V1 A1 ( 2V2 cos 1V1 ) 1,gage where V2 = V1 A1 A2
Fx = Fx , fluid on duct = Fx , duct on fluid = P A1 P2,gage A2 cos + V1 A1 ( 1V1 2V2 cos ) 1,gage where V2 =
(b)
V1 A1 A2
2 V1 A1 (10 m/s ) ( 0.025 m ) m = =5 A2 0.050 m 2 s
We verify our expression by plugging in the given values: V2 =
and
N N Fx = 78470 2 ( 0.025 m 2 ) 65230 2 ( 0.050 m 2 ) cos (135o ) m m kg m N m m + 998.2 3 10 ( 0.025 m 2 ) (1.01) 10 (1.03) 5 cos (135o ) 2 m s s s kg m/s = 7697.2 N 7700 N to the right
where we give the final answer to three significant digits in keeping with our convention. (c) We predict that the force would maximize at = 180o because the water is turned completely around.
6-29
Chapter 6 Momentum Analysis of Flow Systems 6-43 We are to calculate the force exerted by water on a curved duct for a range of turning angle, and compare to Solution the force computed with CFD.
The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis. (a) We apply the equation derived in the previous problem, for the case in which A1 = A2.
2 Fx = A1 ( P 1,gage P 2,gage cos ) + V1 A ( 1 2 cos ) 1
For example, at V1 = 1 m/s and an angle of 120o, FlowLab gives P1,gage = 182.0914 Pa and P2,gage = 76.5901 Pa, and we get N N Fx = ( 0.025 m 2 ) 182.0914 2 76.5901 2 cos (120o ) m m
kg m N + 998.2 3 1 ( 0.025 m 2 ) 1.00 1.04cos (120o ) = 43.4413 N 43.4 N 2 m s kg m/s where we have rounded to three significant digits. We repeat the calculations for a range of turning angles, and show the results in the table below. Note that pressures P1 and P2 are outputs from the CFD code, and are gage pressures.
2
The agreement between analysis and CFD is excellent at the larger turning angles, but not so great at the small turning angles. Notice how the force reaches a maximum at = 180o because the water is turned completely around.
Discussion Keep in mind that the pressures at the inlet and outlet are taken from the CFD calculations. The main source of error here is the momentum flux correction factor at the inlet and outlet, which we have guessed. However, it turns out that the pressure forces dominate, and the terms in the equation with do not contribute much to the force even poor guesses for 1 and 2 would not change the answers much.
6-30
Chapter 6 Momentum Analysis of Flow Systems 6-44 Solution A firemans hose accelerates water from high pressure, low velocity to atmospheric pressure, high velocity at the nozzle exit plane. The horizontal force exerted on the duct by the water is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The momentum-flux correction factor for each inlet and outlet is given to account for frictional effects and the non-uniformity of the inlet and outlet velocity profiles. Properties
The density of the water is = 998.2 kg/m3. Viscosity does not enter our analysis.
Analysis (a) We take the fluid within the duct as the control volume (see sketch), and designate the inlet by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). & & & Conservation of mass for this one-inlet one-outlet steady flow system is m = m1 = m2 . The mass flow rate is & m = V1 A1 = V2 A2 , and the average Fx d2 speed at the outlet is thus r d1 & V A V A m V2 V1 V2 = = 1 1 = 1 1. A2 A2 A2 x P2 P1 The momentum equation for steady flow u(r) R x-direction is in the & & C.V. Fx on CV = mu mu , where u
out in
is the horizontal velocity component: u1 = V1 and u2 = V2. The total force on the control volume consists of pressure forces at the inlet and outlet plus the total of all forces (including pressure and viscous forces) acting on the control volume by the duct walls. Calling this force Fx, duct on fluid, and assuming it to be in the positive x-direction, we write & & P A1 P2,gage A2 + Fx , duct on fluid = m 2 (V2 ) m1V1 1,gage Note that we must be careful with the signs for forces (including pressure forces) and velocities. Solving for Fx, duct on fluid, VA & and plugging in m = V1 A1 and V2 = 1 1 , we get A2
Fx , duct on fluid = P2,gage
A2 A A1 P A1 + V12 A1 2 1 1 1,gage A1 A2
A2 A1 2 Fx = Fx , fluid on duct = Fx , duct on fluid = P A1 + V1 A1 1 2 1,gage P 2,gage A1 A2 A2 A1 2 = A1 P + V1 1 2 1,gage P 2,gage A1 A2

(b) We verify our expression by plugging in the given values:
Fx =
2 2 2 N N 0.05 kg m N 0.10 123,000 2 0 2 + 998.2 3 4 1.03 1.02 kg m/s 2 4 m m 0.10 m s 0.050 = 583.455 N 583 N to the right
( 0.10 m )
where we give the final answer to three significant digits in keeping with our convention. The direction agrees with our intuition. The fluid is trying to push the duct to the right. A negative value for Discussion Fx, fluid on duct indicates that the initially assumed direction was incorrect, but did not hinder our solution.
6-31
Chapter 6 Momentum Analysis of Flow Systems 6-45 Solution We are to calculate the force exerted by water on a firemans nozzle for a range of inlet velocities, and compare to the force computed with CFD.
The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis. (a) We apply the equation derived in the previous problem,
A2 A1 2 Fx = Fx , fluid on duct = A1 P + V1 1 2 1,gage P 2,gage A1 A2

For example, at an inlet velocity of 10 m/s, FlowLab gives P1,gage = 770,108 Pa and P2,gage = 0 Pa, and we get 2 2 2 N N 0.05 kg m N 2 0.10 Fx = ( 0.10 m ) 770,108 2 0 2 + 998.2 3 10 1.03 1.01 2 4 m m 0.10 m s 0.050 kg m/s = 3688.62 N 3,690 N where we have rounded to three significant digits. We repeat the calculations for a range of inlet velocities, and show the results in the table below. Note that pressures P1 and P2 are outputs from the CFD code, and are gage pressures. The outlet boundary condition in this problem is the P2, gage = 0.
The agreement between our conservation law analysis and the CFD calculations is very good the error is less than 1% for all of the cases except at the lowest inlet velocity.
Discussion The conservation laws are fundamental, so it is no surprise that they work well. The main source of error here is the momentum flux correction factor at the inlet and outlet, which we have guessed. By basic principles, if we know the pressure, area, velocity profile (or the average velocity and momentum flux correction factor) at all inlets and outlets of a control volume, we should be able to predict the net force quite accurately, as illustrated here.
6-32
Chapter 6 Momentum Analysis of Flow Systems 6-46 Solution We are to calculate the force exerted by water on a firemans nozzle for a range of diameter ratios, and compare to the force computed with CFD.
The density is given as = 998.2 kg/m3. Viscosity does not enter our analysis. (a) We apply the equation derived in the previous problem,
A2 A1 2 Fx = Fx , fluid on duct = A1 P + V1 1 2 1,gage P 2,gage A1 A2

where we note that A2/A1 = (d2/d1)2. For example, at an inlet velocity of 1 m/s, and with d2/d1 = 0.2, FlowLab gives P1 ,gage = 330,572 Pa and P2 ,gage = 0 Pa, and we get 2 2 N N kg m N 2 2 1 Fx = ( 0.10 m ) 330,572 2 0 2 ( 0.2 ) + 998.2 3 1 1.03 1.01 2 4 m m m s 0.2 kg m/s = 2406.43 N 2,406 N where we have rounded to three significant digits. We repeat the calculations for a range of diameter ratios, and show the results in the table below. Note that pressures P1 and P2 are outputs from the CFD code, and are gage pressures. The outlet boundary condition in this problem is the P2,gage = 0.
The agreement between our conservation law analysis and the CFD calculations is very good the error is less than 1.5% for all of the cases except as d2/d1 approaches one, in which the force gets very small. The conservation laws are fundamental, so it is no surprise that they work well. The main source of error Discussion here is the momentum flux correction factor at the inlet and outlet, which we have guessed. By basic principles, if we know the pressure, area, velocity profile (or the average velocity and momentum flux correction factor) at all inlets and outlets of a control volume, we should be able to predict the net force quite accurately, as illustrated here. 6-33
Chapter 6 Momentum Analysis of Flow Systems 6-47 Solution A 90 reducer elbow deflects water downwards into a smaller diameter pipe. The resultant force exerted on the reducer by water is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 Frictional effects are negligible in the calculation of the pressure drop (so that the Bernoulli equation can be used). 3 The weight of the elbow and the water in it is disregarded since the gravitational effects are negligible. 4 The momentum-flux correction factor for each inlet and outlet is given to be = 1.04. Properties
Water Analysis We take the water within the elbow as the control volume (see 8 m/s sketch), and designate the inlet by 1 and the outlet by 2. We also designate the 25 cm horizontal coordinate by x (with the direction of flow as being the positive 1 direction) and the vertical coordinate by z. The continuity equation for this one& & & & inlet one-outlet steady flow system is m = m1 = m2 . Noting that m = AV , the mass flow rate of water and its outlet velocity are & m = V1 A1 = V1 (D12 / 4) = (1000 kg/m 3 )(8 m/s)[ (0.25 m) 2 / 4] = 392.7 kg/s FRz & & 392.7 kg/s m m FRx V2 = = = = 22.22 m/s 2 A2 D2 / 4 (1000 kg/m 3 )[ (0.15 m) 2 / 4] P1 The Bernoulli equation for a streamline going through the center of the
2
15 cm
reducing elbow is expressed as

P V12 P V2 1 + + z1 = 2 + 2 + z2 g 2 g g 2 g V 2 V22 P2 = P + g 1 1 2 g + z1 z2
2 2
z x
Control volume
Using gage pressures and substituting, the gage pressure at the outlet becomes
(8 m/s) (22.22 m/s) 1 kN P2 = (300 kPa) + (1000 kg/m 3 )(9.81 m/s 2 ) + 0.5 2 1000 kg m/s 2 2(9.81 m/s )
P2
The momentum equation for steady one-dimensional flow is
& & F = mV mV . We let the x- and z- components

out in
1 kPa = 90.04 kPa 1 kN/m 2
of the resultant of the reaction forces exerted by the reducer elbow on water be FRx and FRz, and assume them to be in the positive directions. Noting that the atmospheric pressure acts from all directions and its effect cancels out, the momentum equations along the x and z axes become
& FRx + P A1 = 0 1mV1 1,gage & FRz + P2,gage A2 = 2 m(V2 ) 0

Note that we should not forget the negative sign for forces (including pressure forces) and velocities in the negative x or z direction. Solving for FRx and FRz, and substituting the given values,
1 kN & FRx = mV1 P1, gage A1 = 1.04(392.7 kg/s)(8 m/s) 1000 kg m/s 2
2 (300 kN/m 2 ) (0.25 m) = 17.99 kN 4
2 1 kN + (90.04 kN/m 2 ) (0.15 m) = 7.484 kN & FRz = mV2 + P2, gage A1 = 1.04(392.7 kg/s)(22.22 m/s) 1000 kg m/s 2 4 The force exerted by the water on the reducer elbow is the negative of this, i.e., Fx, water on reducer = 18.0 kN and Fz, water on reducer = 7.48 kN The magnitude of the resultant force exerted by the water on the reducer, and its line of action from the +x direction are 2 2 FR = FRx + FRz = (17.99) 2 + (7.484) 2 = 19.5 kN
= tan -1
FRz 7.484 = tan -1 = 22.6 17.99 FRx
The direction agrees with our intuition. The water is trying to push the reducer to the right and up. Negative Discussion values for FRx and FRz indicate that the initially assumed directions were incorrect, but did not hinder our solution. 6-34
Chapter 6 Momentum Analysis of Flow Systems 6-48 [Also solved using EES on enclosed DVD] Solution A wind turbine with a given span diameter and efficiency is subjected to steady winds. The power generated and the horizontal force on the supporting mast of the turbine are to be determined.
Assumptions 1 The wind flow is steady and incompressible. 2 The efficiency of the turbine-generator is independent of wind speed. 3 The frictional effects are negligible, and thus none of the incoming kinetic energy is converted to thermal energy. 4 Wind flow is uniform and thus the momentum-flux correction factor is nearly unity, 1. Properties
Wind
(a) The power potential of the wind is its kinetic Analysis & energy, which is V2/2 per unit mass, and mV 2 / 2 for a given mass flow rate:
1 m/s V1 = (25 km/h) = 6.94 m/s 3.6 km/h
& m = 1V1 A1 = 1V1
V1
1
D
V2
D 2
4
V12 2
= (1.25 kg/m 3 )(6.94 m/s)

= (55,200 kg/s) (6.94 m/s) 2
(90 m) 2
4
2
= 55,200 kg/s
1 kW 1 kN m/s = 1330 kW
FR
& & & W max = mke1 = m
1 kN 1000 kg m/s 2
Then the actual power produced becomes

& & Wact = wind turbineW max = (0.32)(1330 kW) = 426 kW
(b) The frictional effects are assumed to be negligible, and thus the portion of incoming kinetic energy not converted to electric power leaves the wind turbine as outgoing kinetic energy. Therefore, V2 V2 & & & & mke 2 = mke1 (1 wind turbine ) m 2 = m 1 (1 wind turbine ) 2 2 or V 2 = V1 1 wind turbine = (6.94 m/s) 1 - 0.32 = 5.72 m/s We choose the control volume around the wind turbine such that the wind is normal to the control surface at the inlet and the outlet, and the entire control surface is at the atmospheric pressure. The momentum equation for steady one-dimensional r r r & & flow is F= mV mV . Writing it along the x-direction (without forgetting the negative sign for forces and
out
in
velocities in the negative x-direction) and assuming the flow velocity through the turbine to be equal to the wind velocity give
1 kN & & & FR = mV2 mV1 = m(V2 V1 ) = (55,200 kg/s)(5.72 - 6.94 m/s) 1000 kg m/s 2
The negative sign indicates that the reaction force acts in the negative x direction, as expected.
= 67.3 kN
This force acts on top of the tower where the wind turbine is installed, and the bending moment it generates Discussion at the bottom of the tower is obtained by multiplying this force by the tower height.
6-35

Angular Momentum Equation
6-49C Solution
We are to compare the angular momentum of two rotating bodies.
Analysis No. The two bodies do not necessarily have the same angular momentum. Two rigid bodies having the same mass and angular speed may have different angular momentums unless they also have the same moment of inertia I. Discussion momentum.
The reason why flywheels have most of their mass at the outermost radius is to maximize the angular
6-50C Solution
Analysis M =
We are to express the angular momentum equation in scalar form about a specified axis. The angular momentum equation about a given fixed axis in this case can be expressed in scalar form as & & & rmV rmV where r is the moment arm, V is the magnitude of the radial velocity, and m is the mass
out
in
flow rate.
Discussion
This is a simplification of the more general angular momentum equation (many terms have dropped out).
6-51C Solution
We are to express the angular momentum equation for a specific (restricted) control volume.
r r r r & Analysis The angular momentum equation in this case is expressed as I = r mV where is the angular r r acceleration of the control volume, and r is the vector from the axis of rotation to any point on the line of action of F .
Discussion
This is a simplification of the more general angular momentum equation (many terms have dropped out).
6-52C Solution
We are to discuss how the angular momentum equation is obtained from the RTT.
Analysis The angular momentum equation is obtained by replacing B in the Reynolds transport theorem by the r r r total angular momentum H sys , and b by the angular momentum per unit mass r V . Discussion
The RTT is a general equation that holds for any property B, either scalar or (as in this case) vector.
6-36
Chapter 6 Momentum Analysis of Flow Systems 6-53 Solution Water enters a two-armed sprinkler vertically, and leaves the nozzles horizontally. For a specified flow rate, the rate of rotation of the sprinkler and the torque required to prevent the sprinkler from rotating are to be determined.
Assumptions 1 The flow is uniform and cyclically steady (i.e., steady from a frame of reference rotating with the sprinkler head). 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 Frictional effects and air drag of rotating components are neglected. 4 The nozzle diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties
We take the density of water to be 1000 kg/m3 = 1 kg/L.
1 2 Water jet jet Water jet jet Tshaft
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation of mass equation for this symmetrical steady flow system is & & & & & & m1 + m 2 = m or V jet, 1 + V jet, 2 = V total since
Vjet, 1 A1
Vjet, 2 A2
A r1 = 50 cm r2 = 35 cm
the density of water is constant. Also, both jets are at the same elevation and pressure, and the frictional effects are said to be negligible. Then on the basis of the Bernoulli equation, both jets must leave the nozzles at the same speed relative to the nozzle, and its value is & V total 35 L/s V jet, r ,1 = V jet, r ,2 = V jet, r = = A jet, total (3 + 5) 10 4 m 2
1m3 1000 L = 43.75 m/s
& Noting that V nozzle = r = 2nr and assuming the sprinkler to rotate in the clockwise direction, the absolute water jet speeds in the tangential direction can be expressed as V jet, 1 = V jet, r ,1 + V nozzle, 1 = V jet, r + r1 (Nozzle and water jet move in the same direction). V jet, 2 = V jet, r ,2 V nozzle, 2 = V jet, r r2 (Nozzle and water jet move in opposite directions).
The angular momentum equation about the axis of rotation can be expressed as
& & M = rmV rmV

out in
where r is the
average moment arm, V is the average absolute speed (relative to an inertial reference frame), all moments in the counterclockwise direction are positive, and all moments in the clockwise direction are negative. Momentum flows in the clockwise direction are also negative. Then the angular momentum equation becomes
& & Tshaft = r1m jet,1V jet, 1 + r2 m jet,2V jet, 2

& Noting that m jet = AV jet, r and rearranging,
& & Tshaft = r1m jet,1 (V jet, r + r1 ) + r2 m jet,2 (V jet, r r2 )
Tshaft = V jet [(r2 A2 r1 A1 )V jet, r (r12 A1 + r22 A2 ) ] (a) In the case of free spin with no frictional effects, we have Tshaft = 0 and thus 0 = (r2 A2 r1 A1 )V jet, r (r12 A1 + r22 A2 ) .
Then angular speed and the rate of rotation of sprinkler head becomes (r2 A2 r1 A1 )V jet, r [(35 5 50 3) cm 3 )(4375 cm/s) (50 3 + 35 5) cm
2 2 4
r12 A1
+ r22 A2
= 8.028 rad/s and
& n=
2.028 rad/s 60 s = 76.7 rpm 2 1 min
(b) When the sprinkler is prevented from rotating, we have = 0. Then the required torque becomes (1 m) 3 1 N Tshaft = V jet 2 (r2 A2 r1 A1 ) = (1000 kg/m 3 )(43.75 m/s) 2 [(35 5 50 3) cm 3 ] (100 cm) 3 1 kg m/s 2
= 47.9 N m
Discussion
The rate of rotation determined in (a) will be lower in reality because of frictional effects and air drag.
6-37
Chapter 6 Momentum Analysis of Flow Systems 6-54 Solution Water enters a two-armed sprinkler vertically, and leaves the nozzles horizontally. For a specified flow rate, the rate of rotation of the sprinkler and the torque required to prevent the sprinkler from rotating are to be determined.
We take the density of water to be 1000 kg/m3 = 1 kg/L. 1 2 Water jet V jet, 2 jet
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation of mass equation for this symmetrical steady flow system is & & & & & & m1 + m 2 = m or V jet, 1 + V jet, 2 = V total since
the density of water is constant. Also, both jets are at the same elevation and pressure, and the frictional effects are said to be negligible. Then on the basis of the Bernoulli equation, both jets must leave the nozzles at the same speed relative to the nozzle, and its value is
V jet, r ,1 = V jet, r ,2 = V jet, r =
Vjet, 1 A1
Water jet jet
A2
Tshaft
A r1 = 50 cm r2 = 35 cm
& V total 50 L/s = A jet, total (3 + 5) 10 4 m 2
1m3 1000 L = 62.5 m/s
& Noting that V nozzle = r = 2nr and assuming the sprinkler to rotate in the clockwise direction, the absolute water jet speeds in the tangential direction can be expressed as
V jet, 1 = V jet, r ,1 + V nozzle, 1 = V jet, r + r1 (Nozzle and water jet move in the same direction). V jet, 2 = V jet, r ,2 V nozzle, 2 = V jet, r r2 (Nozzle and water jet move in opposite directions).
& & M = rm V rm V
out in
where r is the
average moment arm, V is the average absolute speed (relative to an inertial reference frame), all moments in the counterclockwise direction are positive, and all moments in the clockwise direction are negative. Momentum flows in the clockwise direction are also negative. Then the angular momentum equation becomes
& & Tshaft = r1m jet,1V jet, 1 + r2 m jet,2V jet, 2

& Noting that m jet = AV jet, r and rearranging,
& & Tshaft = r1m jet,1 (V jet, r + r1 ) + r2 m jet,2 (V jet, r r2 )
Tshaft = V jet [(r2 A2 r1 A1 )V jet, r ( r12 A1 + r22 A2 ) ] (a) In the case of free spin with no frictional effects, we have Tshaft = 0 and thus 0 = (r2 A2 r1 A1 )V jet, r (r12 A1 + r22 A2 ) . Then angular speed and the rate of rotation of sprinkler head becomes (r2 A2 r1 A1 )V jet, r [(35 5 50 3) cm 3 )(6250 cm/s) (50 3 + 35 5) cm
2 2 4
r12 A1
+ r22 A2
= 11.47 rad/s and
& n=
11.47 rad/s 60 s = = 110 rpm 2 2 1 min
(b) When the sprinkler is prevented from rotating, we have = 0. Then the required torque becomes
(1 m) 3 Tshaft = V jet 2 (r2 A2 r1 A1 ) = (1000 kg/m 3 )(62.5 m/s) 2 [(35 5 50 3) cm 3 ] (100 cm) 3
1N 1 kg m/s 2
= 97.7 N m
Discussion
The rate of rotation determined in (a) will be lower in reality because of frictional effects and air drag. 6-38
Chapter 6 Momentum Analysis of Flow Systems 6-55 Solution Water is pumped through a piping section. The moment acting on the elbow for the cases of downward and upward discharge is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. 3 Effects of water falling down during upward discharge is disregarded. 4 Pipe outlet diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties
r2 = 2 m
Analysis We take the entire pipe as the control volume, and designate the inlet by 1 and the outlet by 2. We also take the x and y coordinates as shown. The control volume and the reference frame are fixed. The conservation of mass & & & equation for this one-inlet one-outlet steady flow system is m1 = m 2 = m , and V1 = V 2 = V since Ac = constant. The mass flow rate and the weight of the horizontal section of the pipe are
& m = AcV = (1000 kg/m 3 )[ (0.15 m) 2 / 4](7 m/s) = 123.7 kg/s
MA A
r1 = 1 m
r & mV1
r & mV 2
1N W = mg = (15 kg/m)(2 m)(9.81 m/s 2 ) 1 kg m/s 2
= 294.3 N/m
(a) Downward discharge: To determine the moment acting on the pipe at point A, we need to take the moment of all forces and momentum flows about that point. This is a steady and uniform flow problem, and all forces and momentum flows are in the same plane. Therefore, the angular momentum equation in this case can be expressed as & & M= rmV rmV where r is the moment arm, all moments in the counterclockwise direction are positive, and all
out
in
in the clockwise direction are negative. The free body diagram of the pipe section is given in the figure. Noting that the moments of all forces and momentum flows passing through point A are zero, the only force that will yield a moment about point A is the weight W of the horizontal pipe section, and the only momentum flow that will yield a moment is the outlet stream (both are negative since both moments are in the clockwise direction). Then the angular momentum equation about point A becomes
& M A r1W = r2 mV 2
Solving for MA and substituting,

1N & M A = r1W r2 mV2 = (1 m)(294.3 N) (2 m)(123.7 kg/s)(7 m/s) 1 kg m/s 2 = 1438 N m
The negative sign indicates that the assumed direction for MA is wrong, and should be reversed. Therefore, a moment of 70 Nm acts at the stem of the pipe in the clockwise direction. (b) Upward discharge: The moment due to discharge stream is positive in this case, and the moment acting on the pipe at point A is
1N & M A = r1W + r2 mV2 = (1 m)(294.3 N) + (2 m)(123.7 kg/s)(7 m/s) 1 kg m/s 2 = 2026 N m
Note direction of discharge can make a big difference in the moments applied on a piping system. This Discussion problem also shows the importance of accounting for the moments of momentums of flow streams when performing evaluating the stresses in pipe materials at critical cross-sections.
6-39
Chapter 6 Momentum Analysis of Flow Systems 6-56 Solution A two-armed sprinkler is used to generate electric power. For a specified flow rate and rotational speed, the power produced is to be determined.
Assumptions 1 The flow is cyclically steady (i.e., steady from a frame of reference rotating with the sprinkler head). 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 Generator losses and air drag of rotating components are neglected. 4 The nozzle diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties We take the density of water to be 1000 kg/m3. Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation & & & of mass equation for this steady flow system is m1 = m 2 = m . Noting & nozzle = m / 2 or & that the two nozzles are identical, we have m V& = V& / 2 since the density of water is constant. The average
nozzle
V jet
Electric generator
& m total = 30 L/s
V jet
total
jet outlet velocity relative to the nozzle is & V 0.015 m 3 /s = 113.0 m/s V jet = nozzle = Ajet [ (0.013 m) 2 / 4] The angular and tangential velocities of the nozzles are
& m nozzleV r
Mshaft
& = 2n = 2 (250 rev/min) Vnozzle
1 min = 26.18 rad/s 60 s = r = (0.6 m)(26.18 rad/s) = 15.71 m/s
The velocity of water jet relative to the control volume (or relative to a fixed location on earth) is Vr = V jet Vnozzle = 113.0 15.71 = 97.29 m/s The angular momentum equation can be expressed as & & M = rmV rmV
r = 0.6 m
out
in
& m nozzleV r
where all moments in the counterclockwise direction are positive, and all in the clockwise direction are negative. Then the angular momentum equation about the axis of rotation becomes & & M shaft = 2rm nozzleV r or M shaft = rm total V r Substituting, the torque transmitted through the shaft is determined to be
1N & M shaft = rm totalVr = (0.6 m)(30 kg/s)(97.29 m/s) 1 kg m/s 2
& & since mtotal = Vtotal = (1000 kg/m 3 )(0.030 m 3 /s) = 30 kg/s .
= 1751 N m
Then the power generated becomes

1 kW & & W = 2nM shaft = M shaft = (26.18 rad/s)(1751 N m) = 45.8 kW 1000 N m/s
Therefore, this sprinkler-type turbine has the potential to produce 45.8 kW of power.
Discussion This is, of course, the maximum possible power. The actual power generated would be much smaller than this due to all the irreversible losses that we have ignored in this analysis.
6-40
Chapter 6 Momentum Analysis of Flow Systems 6-57 Solution A two-armed sprinkler is used to generate electric power. For a specified flow rate and rotational speed, the moment acting on the rotating head when the head is stuck is to be determined.
V jet
Electric generator
& m nozzleV r
Mshaft
r = 0.6 m
& m nozzleV r
& mtotal = 30 L/s
V jet
Assumptions 1 The flow is uniform and steady. 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 The nozzle diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties We take the density of water to be 1000 kg/m3. Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The & & & conservation of mass equation for this steady flow system is m1 = m 2 = m . Noting that the two nozzles are identical, we & & / 2 since the density of water is constant. The average jet outlet velocity relative to the & & have m = m / 2 or V =V
nozzle
nozzle total
nozzle is
V jet =
& Vnozzle 0.015 m 3 /s = = 113.0 m/s Ajet [ (0.013 m) 2 / 4] & & M = rmV rmV
out in
The angular momentum equation can be expressed as
where all moments in the
counterclockwise direction are positive, and all in the clockwise direction are negative. Then the angular momentum equation about the axis of rotation becomes & & or M shaft = 2rm nozzleV jet M shaft = rm total V jet
Substituting, the torque transmitted through the shaft is determined to be

1N & M shaft = rmtotalV jet = (0.6 m)(30 kg/s)(113.0 m/s) 1 kg m/s 2
& & since mtotal = Vtotal = (1000 kg/m 3 )(0.030 m 3 /s) = 30 kg/s .
= 2034 N m
Discussion When the sprinkler is stuck and thus the angular velocity is zero, the torque developed is maximum since V nozzle = 0 and thus Vr = V jet = 113.0 m/s , giving M shaft,max = 2034 N m . But the power generated is zero in this case
since the shaft does not rotate.
6-41
Chapter 6 Momentum Analysis of Flow Systems 6-58 Solution A three-armed sprinkler is used to water a garden. For a specified flow rate and resistance torque, the angular velocity of the sprinkler head is to be determined.
Assumptions 1 The flow is uniform and cyclically steady (i.e., steady from a frame of reference rotating with the sprinkler head). 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 Air drag of rotating components are neglected. 4 The nozzle diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties
V jet
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation & & & of mass equation for this steady flow system is m1 = m 2 = m . Noting & & that the three nozzles are identical, we have m nozzle = m / 3 or & & V =V / 3 since the density of water is constant. The average jet
nozzle
Electric generator
total
outlet velocity relative to the nozzle and the mass flow rate are
V jet =
V&nozzle
Ajet
1 m3 = 113.2 m/s 3[ (0.015 m) 2 / 4] 1000 L
60 L/s
V&total = 60 L/s
V jet
& mtotal = V&total = (1 kg/L)(60 L/s) = 60 kg/s
The angular momentum equation can be expressed as & & M = rmV rmV
out
in
& m nozzleV r
where all moments in the counterclockwise direction are positive, and all in the clockwise direction are negative. Then the angular momentum equation about the axis of rotation becomes
& m nozzleV r
To = 50 Nm
& T0 = 3rm nozzleV r
or
& T0 = rm total V r r = 40 cm
= 2.08 m/s
Solving for the relative velocity Vr and substituting, 1 kg m/s 2 T0 50 N m = Vr = & 1N rm total (0.40 m)(60 kg/s)
Then the tangential and angular velocity of the nozzles become

Vnozzle = V jet Vr = 113.2 2.08 = 111.1 m/s
& m nozzleV r
Vnozzle 111.1 m/s = = 278 rad/s r 0.4 m 278 rad/s 60 s & n= = = 2652 rpm 2650 rpm 2 2 1 min
Therefore, this sprinkler will rotate at 2650 revolutions per minute (to three significant digits).
Discussion
The actual rotation rate will be somewhat lower than this due to air friction as the arms rotate.
6-42
Chapter 6 Momentum Analysis of Flow Systems 6-59 Solution A centrifugal blower is used to deliver atmospheric air. For a given angular speed and power input, the volume flow rate of air is to be determined.
Impeller shroud b1 In r1 Shaft
b2 r2
r2 r1
r V2,t
r V1,t
Impeller blade
Impeller
Impeller region
Assumptions 1 The flow is steady in the mean. 2 Irreversible losses are negligible. 3 The tangential components of air velocity at the inlet and the outlet are said to be equal to the impeller velocity at respective locations. Properties
The gas constant of air is 0.287 kPam3/kgK. The density of air at 20C and 95 kPa is 95 kPa P = = 1.130 kg/m 3 RT (0.287 kPa m 3 /kg K)(293 K)
Analysis In the idealized case of the tangential fluid velocity being equal to the blade angular velocity both at the inlet and the outlet, we have V1,t = r1 and V 2,t = r2 , and the torque is expressed as
& & Tshaft = m(r2V 2,t r1V1,t ) = m ( r22 r12 ) = V& (r22 r12 )
where the angular velocity is

& = 2n = 2 (900 rev/min)
1 min = 94.25 rad/s 60 s
Then the shaft power becomes & Wshaft = Tshaft = V& 2 (r22 r12 ) Solving for V& and substituting, the volume flow rate of air is determined to
V& =
& Wshaft
(r22
r12 )
1 kg m/s 2 1N (1.130 kg/m 3 )(94.25 rad/s) 2 [(0.30 m) 2 (0.18 m) 2 ]
120 N m/s
= 0.2075 m 3 /s
The normal velocity components at the inlet and the outlet are
V1,n = V 2, n =
V& 0.2075 m 3 /s = = 3.01 m/s 2r1b1 2 (0.18 m)(0.061 m) V& 0.2075 m 3 /s = = 3.24 m/s 2r2 b2 2 (0.30 m)(0.034 m)
Discussion Note that the irreversible losses are not considered in this analysis. In reality, the flow rate and the normal components of velocities will be smaller.
6-43
Chapter 6 Momentum Analysis of Flow Systems 6-60 Solution A centrifugal blower is used to deliver atmospheric air at a specified rate and angular speed. The minimum power consumption of the blower is to be determined.
2 = 50
b2 r2
r2 r1
r V2 r V1
Impeller blade
Impeller
Impeller region
Assumptions Properties Analysis outlet are
1 The flow is steady in the mean. 2 Irreversible losses are negligible.

The density of air is given to be 1.25 kg/m3. We take the impeller region as the control volume. The normal velocity components at the inlet and the 0.70 m 3 /s V& = = 6.793 m/s 2r1b1 2 (0.20 m)(0.082 m)
V1,n = V 2, n =
V& 0.70 m 3 /s = = 4.421 m/s 2r2 b2 2 (0.45 m)(0.056 m)

V1,t = V1,n tan 1 = 0 V 2,t = V 2,n tan 1 = ( 4.421 m/s ) tan 50 = 5.269 m/s
The tangential components of absolute velocity are:

1 = 0: 2 = 50:
The angular velocity of the propeller is 1 min & = 2n = 2 (700 rev/min) = 73.30 rad/s 60 s & m = V& = (1.25 kg/m 3 )(0.7 m 3 /s) = 0.875 kg/s Normal velocity components V1,n and V2,n as well pressure acting on the inner and outer circumferential areas pass through the shaft center, and thus they do not contribute to torque. Only the tangential velocity components contribute to torque, and the application of the angular momentum equation gives
1N & Tshaft = m( r2V 2,t r1V1,t ) = (0.875 kg/s)[(0.45 m)(5.269 m/s) - 0] 1 kg m/s 2 = 2.075 N m
Then the shaft power becomes

1W & W = Tshaft = (73.30 rad/s)(2.075 N m) = 152 W 1 N m/s
Discussion The actual required shaft power is greater than this, due to the friction and other irreversibilities that we have neglected in our analysis. Nevertheless, this is a good first approximation.
6-44
Chapter 6 Momentum Analysis of Flow Systems 6-61 Solution The previous problem is reconsidered. The effect of discharge angle 2 on the minimum power input requirements as 2 varies from 0 to 85 in increments of 5 is to be investigated.
Analysis
1600 1400 1200 1000
rho=1.25 "kg/m3" r1=0.20 "m" b1=0.082 "m" r2=0.45 "m" b2=0.056 "m" V_dot=0.70 "m3/s" V1n=V_dot/(2*pi*r1*b1) "m/s" V2n=V_dot/(2*pi*r2*b2) "m/s" Alpha1=0 V1t=V1n*tan(Alpha1) "m/s" V2t=V2n*tan(Alpha2) "m/s" n_dot=700 "rpm" omega=2*pi*n_dot/60 "rad/s" m_dot=rho*V_dot "kg/s" T_shaft=m_dot*(r2*V2t-r1*V1t) "Nm" W_dot_shaft=omega*T_shaft "W"
Wshaft, W
800 600 400 200 0 0 10 20 30 40 50 60 70 80 90
Angle, 2 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85
V2,t, m/s
0.00 0.39 0.78 1.18 1.61 2.06 2.55 3.10 3.71 4.42 5.27 6.31 7.66 9.48 12.15 16.50 25.07 50.53
Torque, Tshaft, Nm 0.00 0.15 0.31 0.47 0.63 0.81 1.01 1.22 1.46 1.74 2.07 2.49 3.02 3.73 4.78 6.50 9.87 19.90
Shaft power,
& Wshaft , W
0 11 23 34 46 60 74 89 107 128 152 182 221 274 351 476 724 1459
Discussion When 2 = 0, the shaft power is also zero as expected, since there is no turning at all. As 2 approaches 90o, the required shaft power rises rapidly towards infinity. We can never reach 2 = 90o because this would mean zero flow normal to the outlet, which is impossible.
6-45
Chapter 6 Momentum Analysis of Flow Systems 6-62 Solution A centrifugal pump is used to supply water at a specified rate and angular speed. The minimum power consumption of the pump is to be determined.
2 = 60
b2 r2
r2 r1
r V2 r V1
Impeller blade
Impeller
Impeller region
Assumptions Properties Analysis outlet are
1 The flow is steady in the mean. 2 Irreversible losses are negligible.

We take the density of water to be 1000 kg/m3. We take the impeller region as the control volume. The normal velocity components at the inlet and the 0.15 m 3 /s V& = = 2.296 m/s 2r1b1 2 (0.13 m)(0.080 m)
V1,n = V 2, n =
V& 0.15 m 3 /s = = 2.274 m/s 2r2 b2 2 (0.30 m)(0.035 m)

V1,t = V1,n tan 1 = 0 V 2,t = V 2,n tan 1 = (2.274 m/s ) tan 60 = 3.938 m/s
The tangential components of absolute velocity are:

1 = 0: 2 = 60:
The angular velocity of the propeller is 1 min & = 2n = 2 (1200 rev/min) = 125.7 rad/s 60 s & m = V& = (1000 kg/m 3 )(0.15 m 3 /s) = 150 kg/s Normal velocity components V1,n and V2,n as well pressure acting on the inner and outer circumferential areas pass through the shaft center, and thus they do not contribute to torque. Only the tangential velocity components contribute to torque, and the application of the angular momentum equation gives
1 kN & Tshaft = m(r2V 2,t r1V1,t ) = (150 kg/s)[(0.30 m)(3.938 m/s) - 0] 1000 kg m/s 2 = 177.2 kN m
Then the shaft power becomes

1 kW & W = Tshaft = (125.7 rad/s)(177.2 kN m) = 22.3 kW 1 kN m/s
Discussion larger.
Note that the irreversible losses are not considered in analysis. In reality, the required power input will be
6-46
Chapter 6 Momentum Analysis of Flow Systems 6-63 Solution A Pelton wheel is considered for power generation in a hydroelectric power plant. A relation is to be obtained for power generation, and its numerical value is to be obtained.
Mshaft
r
Shaft
Vj - r
Vj - r
Nozzle
Vj
Assumptions 1 The flow is uniform and cyclically steady. 2 The water is discharged to the atmosphere, and thus the gage pressure at the nozzle outlet is zero. 3 Friction and losses due to air drag of rotating components are neglected. 4 The nozzle diameter is small compared to the moment arm, and thus we use average values of radius and velocity at the outlet. Properties
& Analysis The tangential velocity of buckets corresponding to an angular velocity of = 2n is V bucket = r . Then the relative velocity of the jet (relative to the bucket) becomes
V r = V j V bucket = V j r
We take the imaginary disk that contains the Pelton wheel as the control volume. The inlet velocity of the fluid into this control volume is Vr, and the component of outlet velocity normal to the moment arm is Vrcos. The angular momentum & & equation can be expressed as M = rm V rmV where all moments in the counterclockwise direction are
out
in
positive, and all in the clockwise direction are negative. Then the angular momentum equation about the axis of rotation becomes
& & M shaft = rmV r cos rmV r & & or M shaft = rmV r (1 cos ) = rm(V j r )(1 cos )
& & & Noting that Wshaft = 2nM shaft = M shaft and m = V& , the shaft power output of a Pelton turbine becomes
& Wshaft = V&r (V j r )(1 cos )
which is the desired relation. For given values, the shaft power output is determined to be
1 MW & Wshaft = (1000 kg/m 3 )(10 m 3 /s )(2 m)(15.71 rad/s)(50 - 2 15.71 m/s)(1 - cos160) 6 = 11.3 MW 10 N m/s
where
& = 2n = 2 (150 rev/min)
1 min = 15.71 rad/s 60 s
Discussion The actual power will be somewhat lower than this due to air drag and friction. Note that this is the shaft power; the electrical power generated by the generator connected to the shaft is lower due to generator inefficiencies.
6-47
Chapter 6 Momentum Analysis of Flow Systems 6-64 Solution The previous problem is reconsidered. The effect of on the power generation as varies from 0 to 180 is to be determined, and the fraction of power loss at 160 is to be assessed.
Analysis
rho=1000 "kg/m3" r=2 "m" V_dot=10 "m3/s" V_jet=50 "m/s" n_dot=150 "rpm" omega=2*pi*n_dot/60 V_r=V_jet-r*omega m_dot=rho*V_dot W_dot_shaft=m_dot*omega*r*V_r*(1-cos(Beta))/1E6 "MW" W_dot_max=m_dot*omega*r*V_r*2/1E6 "MW" Efficiency=W_dot_shaft/W_dot_max Angle, 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
12
Max power,
Actual power,
Efficiency,
& W max , MW
11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7 11.7
& Wshaft , MW
0.00 0.09 0.35 0.78 1.37 2.09 2.92 3.84 4.82 5.84 6.85 7.84 8.76 9.59 10.31 10.89 11.32 11.59 11.68
0.000 0.008 0.030 0.067 0.117 0.179 0.250 0.329 0.413 0.500 0.587 0.671 0.750 0.821 0.883 0.933 0.970 0.992 1.000
Wmax
10 8
Wshaft
Wshaft
6 4 2 0 0
20
40
60
80
100
120
140
160
180
Discussion
The efficiency of a Pelton wheel for =160 is 0.97. Therefore, at this angle, only 3% of the power is lost.
6-48

Review Problems
6-65 Solution Water enters a two-armed sprinkler vertically, and leaves the nozzles horizontally at an angle to tangential direction. For a specified flow rate and discharge angle, the rate of rotation of the sprinkler and the torque required to prevent the sprinkler from rotating are to be determined. EES
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation of mass equation for this symmetrical steady flow system is & & & m1 = m 2 = m . Noting that the two nozzles & & are identical, we have m jet = m total / 2 or
& & V jet = V total / 2 since the density of water is
= 60
Vjet, 1
1
A r1 = 40 cm
Tshaft
r2 = 40 cm
Vjet, 2
2
constant. The average jet outlet velocity relative to the nozzle is
= 60
V jet, r =
& V jet
A jet
1m3 = 66.31 m/s (0.012 m) / 4 1000 L
15 / 2 L/s
& & M = rm V rm V
out in
where r is the
average moment arm, V is the average absolute speed (relative to an inertial reference frame), all moments in the counterclockwise direction are positive, and all moments in the clockwise direction are negative. Momentum flows in the clockwise direction (as in this case) are also negative. The absolute water jet speed in the tangential direction is the & difference between the tangential component of the water jet speed and the nozzle speed V nozzle = r = 2nr . Thus, V jet,t = V jet, r, t V nozzle = V jet, r cos r . Then the angular momentum equation becomes
& & Tshaft = r1m jet,1V jet, t ,1 r2 m jet,2V jet, t , 2
& & Tshaft = r1m jet,1 (V jet, r ,1 cos 1 r1 ) + r2 m jet,2 (V jet, r ,2 cos 2 r2 )
Noting that r1 = r2 = r , 1 = 2 = , V jet, r ,1 = V jet, r ,2 = V jet, r , and, the angular momentum equation becomes
& Tshaft = rV total (V jet, r cos r )
(a) In the case of free spin with no frictional effects, we have Tshaft = 0 and thus V jet, r cos r = 0 . Then angular speed and the rate of rotation of sprinkler head becomes
V jet, r cos r (66.31 m/s)cos60 = 82.9 rad/s and 0.40 m
& n=
82.9 rad/s 60 s = = 792 rpm 2 2 1 min
1N & Tshaft = rV totalV jet, r cos = (0.4 m)(1 kg/L)(15 L/s)(66.31 m/s) cos 60 1 kg m/s 2 = 199 N m
Discussion
The rate of rotation determined in (a) will be lower in reality because of frictional effects and air drag. 6-49
Chapter 6 Momentum Analysis of Flow Systems 6-66 Solution Water enters a two-armed sprinkler vertically, and leaves the nozzles horizontally at an angle to tangential direction. For a specified flow rate and discharge angle, the rate of rotation of the sprinkler and the torque required to prevent the sprinkler from rotating are to be determined.
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation of mass equation for this symmetrical steady & & & flow system is m1 = m 2 = m . Noting that the two nozzles are identical, we have & & & & m jet = m total / 2 or V jet = V total / 2 since the
= 60
Vjet, 1
1
A r1 = 60 cm
Tshaft
density of water is constant. The average jet outlet velocity relative to the nozzle is
V jet, r =
r2 = 20 cm
Vjet, 2
2 60
& V jet
A jet
1m3 = 66.31 m/s = (0.012 m) 2 / 4 1000 L

15 / 2 L/s
& & M = rm V rm V
out in
where r is the
average moment arm, V is the average absolute speed (relative to an inertial reference frame), all moments in the counterclockwise direction are positive, and all moments in the clockwise direction are negative. Momentum flows in the clockwise direction (as in this case) are also negative. The absolute water jet speed in the tangential direction is the & difference between the tangential component of the water jet speed and the nozzle speed V nozzle = r = 2nr . Thus, V jet,t = V jet, r, t V nozzle = V jet, r cos r . Then the angular momentum equation becomes
& & Tshaft = r1 m jet,1V jet, t ,1 r2 m jet,2V jet, t , 2
& & Tshaft = r1m jet,1 (V jet, r ,1 cos 1 r1 ) + r2 m jet,2 (V jet, r ,2 cos 2 r2 )
Noting that 1 = 2 = , V jet, r ,1 = V jet, r ,2 = V jet, r , and, the angular momentum equation becomes
& & Tshaft = V jet [r1 (V jet, r cos r1 ) + r2 (V jet, r cos r2 )] or Tshaft = V jet [(r1 + r2 )V jet, r cos (r12 + r22 ) ]
(a) In the case of free spin with no frictional effects, we have Tshaft = 0 and thus 0 = (r1 + r2 )V jet, r cos (r12 + r22 ) . Then angular speed and the rate of rotation of sprinkler head becomes
(r1 + r2 ))V jet, r cos r12 + r22 (0.6 + 0.2m )(66.31 m/s)cos60 (0.60 m) 2 + (0.20 m) 2
= 66.31 rad/s and
& n=
66.31 rad/s 60 s = 633 rpm 2 1 min
1N & Tshaft = (r1 + r2 ) V jet V jet, r cos = (0.6 + 0.2 m )(1 kg/L )(15 / 2 L/s )(66.31 m/s ) cos 60 1 kg m/s 2 1 9 9 N m =
Discussion
The rate of rotation determined in (a) will be lower in reality because of frictional effects and air drag.
6-50
Chapter 6 Momentum Analysis of Flow Systems 6-67 Solution An ice skater is holding a flexible hose (essentially weightless) which directs a stream of water horizontally at a specified velocity. The velocity and the distance traveled in 5 seconds, and the time it takes to move 5 m and the velocity at that moment are to be determined.
Assumptions 1 Friction between the skates and ice is negligible. 2 The flow of water is steady and one-dimensional (but the motion of skater is unsteady). 3 The ice skating arena is level, and the water jet is discharged horizontally. 4 The mass of the hose and the water in it is negligible. 5 The skater is standing still initially at t = 0. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties Analysis
We take the density of water to be 1000 kg/m3. (a) The mass flow rate of water through the hose is
& m = AV =
D 2
4
V = (1000 kg/m 3 )
(0.02 m) 2
4
(10 m/s) = 3.14 kg/s
The thrust exerted on the skater by the water stream is simply the momentum flux of the water stream, and it acts in the reverse direction,
1N & F = Thrust = mV = (3.14 kg/s)(10 m/s) 1 kg m/s 2 = 31.4 N (constant)
The acceleration of the skater is determined from Newtons 2nd law of motion F = ma where m is the mass of the skater,
a=
F 31.4 N 1 kg m/s 2 = m 60 kg 1N
= 0.523 m/s 2
Note that thrust and thus the acceleration of the skater is constant. The velocity of the skater and the distance traveled in 5 s are
Vskater = at = (0.523 m/s 2 )(5 s) = 2.62 m/s x = 1 at 2 = 1 (0.523 m/s 2 )(5 s) 2 = 6.54 m 2 2
F
10 m/s
D = 2 cm
(b) The time it will take to move 5 m and the velocity at that moment are
x = 1 at 2 2 t= 2x = a 2(5 m) 0.523 m/s 2 = 4.4 s
Hose
Vskater = at = (0.523 m/s 2 )(4.4 s) = 2.3 m/s
In reality, the velocity of the skater will be lower because of friction on ice and the resistance of the hose to Discussion & follow the skater. Also, in the mV expressions, V is the fluid stream speed relative to a fixed point. Therefore, the correct & (V jet Vskater ) , and the analysis above is valid only when the skater speed is low relative to expression for thrust is F = m the jet speed. An exact analysis would result in a differential equation.
6-51
Chapter 6 Momentum Analysis of Flow Systems 6-68 Solution It is to be shown that the force exerted by a liquid jet of velocity V on a stationary nozzle is proportional to & V2, or alternatively, to m 2 .
Assumptions 1 The flow is steady and incompressible. 2 The nozzle is given to be stationary. 3 The nozzle involves a 90 turn and thus the incoming and outgoing flow streams are normal to each other. 4 The water is discharged to the atmosphere, and thus the gage pressure at the outlet is zero. FRx Analysis We take the nozzle as the control volume, and the flow y direction at the outlet as the x axis. Note that the nozzle makes a 90 V turn, and thus it does not contribute to any pressure force or momentum & x flux term at the inlet in the x direction. Noting that m = AV where A Nozzle is the nozzle outlet area and V is the average nozzle outlet velocity, the momentum equation for steady one-dimensional flow in the x direction Liquid reduces to r r r & & & & FRx = m out Vout = mV F= mV mV
out
in
where FRx is the reaction force on the nozzle due to liquid jet at the nozzle outlet. Then,
& m = AV & FRx = mV = AVV = AV 2
& & or FRx = mV = m
& & m m2 = A A
Therefore, the force exerted by a liquid jet of velocity V on this stationary nozzle is proportional to V2, or & alternatively, to m 2 .
Discussion If there were not a 90o turn, we would need to take into account the momentum flux and pressure contributions at the inlet.
6-52
Chapter 6 Momentum Analysis of Flow Systems 6-69 Solution A fireman was hit by a nozzle held by a tripod with a rated holding force. The accident is to be investigated by calculating the water velocity, the flow rate, and the nozzle velocity.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure of the water jet is the atmospheric pressure, which is disregarded since it acts on all surfaces. 3 Gravitational effects and vertical forces are disregarded since the horizontal resistance force is to be determined. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. 5 Upstream pressure and momentum effects are ignored. Properties
We take the nozzle and the horizontal portion of the hose as the system such that water enters the control Analysis volume vertically and outlets horizontally (this way the pressure force and the momentum flux at the inlet are in the vertical direction, with no contribution to the force balance in the horizontal direction, and designate the entrance by 1 and the outlet by 2. We also designate the horizontal coordinate by x (with the direction of flow as being the positive direction). The momentum equation for steady one-dimensional flow is
& & F = mV mV . We let the horizontal
out in
force applied by the tripod to the nozzle to hold it be FRx, and assume it to be in the positive x direction. Then the momentum equation along the x direction becomes
& & FRx = mVe 0 = mV = AVV =
D 2
4
V2
1 kg m/s 2 (1800 N) 1N
2 = (1000 kg/m 3 ) (0.05 m) V 2 4
Solving for the water outlet velocity gives V = 30.3 m/s. Then the water flow rate becomes
Nozzle
V& = AV =
D
4
V=
(0.05 m)
4
(30.3 m/s) = 0.0595 m 3 /s
FRx
D = 5 cm
When the nozzle was released, its acceleration must have been
a nozzle =
F m nozzle
1800 N 1 kg m/s 2 10 kg 1N
= 180 m/s 2
Tripod
Assuming the reaction force acting on the nozzle and thus its acceleration to remain constant, the time it takes for the nozzle to travel 60 cm and the nozzle velocity at that moment were (note that both the distance x and the velocity V are zero at time t = 0)
x = 1 at 2 2 t= 2(0.6 m) 2x = = 0.0816 s a 180 m/s 2
V = at = (180 m/s 2 )(0.0816 s) = 14.7 m/s
Thus, we conclude that the nozzle hit the fireman with a velocity of 14.7 m/s.
Discussion Engineering analyses such as this one are frequently used in accident reconstruction cases, and they often form the basis for judgment in courts.
6-53
Chapter 6 Momentum Analysis of Flow Systems 6-70 Solution During landing of an airplane, the thrust reverser is lowered in the path of the exhaust jet, which deflects the exhaust and provides braking. The thrust of the engine and the braking force produced after the thrust reverser is deployed are to be determined.
Assumptions 1 The flow of exhaust gases is steady and one-dimensional. 2 The exhaust gas stream is exposed to the atmosphere, and thus its pressure is the atmospheric pressure. 3 The velocity of exhaust gases remains constant during reversing. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Analysis direction,
(a) The thrust exerted on an airplane is simply the momentum flux of the combustion gases in the reverse
= 5400 N
1N & Thrust = mexVex = (18 kg/s)(300 m/s) 1 kg m/s 2
(b) We take the thrust reverser as the control volume such that it cuts through both exhaust streams normally and the connecting bars to the airplane, and the direction of airplane as the positive direction of x axis. The momentum equation for steady one-dimensional flow in the x direction reduces to r r r & & & & & F= mV mV FRx = m(V )cos20 m(V ) FRx = (1 + cos 20)mVi
out
in
Substituting, the reaction force is determined to be
FRx = (1 + cos 30)(18 kg/s)(300 m/s) = 10,077 N

The breaking force acting on the plane is equal and opposite to this force,
Fbreaking = 10,077 N 10,100 N
Therefore, a braking force of 10,100 N develops in the opposite direction to flight.

= 150
& mV
150 Control volume
300 m/s
& mV
FRx
x
FRx
Discussion This problem can be solved more generally by measuring the reversing angle from the direction of exhaust gases ( = 0 when there is no reversing). When < 90, the reversed gases are discharged in the negative x direction, and the momentum equation reduces to
& & FRx = m( V )cos m(V )
& FRx = (1 cos )mVi
This equation is also valid for > 90 since cos(180-) = - cos. Using = 150, for example, gives & & FRx = (1 cos 150)mVi = (1 + cos 30)mVi , which is identical to the solution above.
6-54
Chapter 6 Momentum Analysis of Flow Systems 6-71 Solution The previous problem is reconsidered. The effect of thrust reverser angle on the braking force exerted on the airplane as the reverser angle varies from 0 (no reversing) to 180 (full reversing) in increments of 10 is to be investigated.
Analysis
V_jet=250 "m/s" m_dot=18 "kg/s" F_Rx=(1-cos(alpha))*m_dot*V_jet "N" Reversing angle, 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 Braking force Fbrake, N 0 68 271 603 1053 1607 2250 2961 3719 4500 5281 6039 6750 7393 7947 8397 8729 8932 9000
9000 8000 7000 6000
Fbrake, N
5000 4000 3000 2000 1000 0 0 20 40 60 80 100 120 140 160 180
Discussion As expected, the braking force is zero when the angle is zero (no deflection), and maximum when the angle is 180o (completely reversed). Of course, it is impossible to completely reverse the flow, since the jet exhaust cannot be directed back into the engine.
6-55
Chapter 6 Momentum Analysis of Flow Systems 6-72 Solution The rocket of a spacecraft is fired in the opposite direction to motion. The deceleration, the velocity change, and the thrust are to be determined.
Assumptions 1 The flow of combustion gases is steady and one-dimensional during the firing period, but the flight of the spacecraft is unsteady. 2 There are no external forces acting on the spacecraft, and the effect of pressure force at the nozzle outlet is negligible. 3 The mass of discharged fuel is negligible relative to the mass of the spacecraft, and thus the spacecraft may be treated as a solid body with a constant mass. 4 The nozzle is well-designed such that the effect of the momentumflux correction factor is negligible, and thus 1. Analysis (a) We choose a reference frame in which the control volume moves with the spacecraft. Then the velocities of fluid steams become simply their relative velocities (relative to the moving body). We take the direction of motion of the spacecraft as the positive direction along the x axis. There are no external forces acting on the spacecraft, and its mass is nearly constant. Therefore, the spacecraft can be treated as a solid body with constant mass, and the momentum equation in this case is r r r r r dVspace d ( mV ) CV & & & 0= + mV mV mspace = m f V f dt dt out in
8200 kg 460 m/s
x
1500 m/s 70 kg/s
Noting that the motion is on a straight line and the discharged gases move in the positive x direction (to slow down the spacecraft), we write the momentum equation using magnitudes as & dVspace dVspace mf & mspace = m f V f = Vf dt dt mspace Substituting, the deceleration of the spacecraft during the first 5 seconds is determined to be & dVspace mf 70 kg/s aspace = = Vf = (1500 m/s) = - 12.8 m/s 2 8200 kg dt mspace (b) Knowing the deceleration, which is constant, the velocity change of the spacecraft during the first 5 seconds is determined from the definition of acceleration a space = dVspace / dt to be
dVspace = aspace dt
Vspace = aspace t = (-12.8 m/s 2 )(5 s) = 64.0 m/s
(c) The thrust exerted on the system is simply the momentum flux of the combustion gases in the reverse direction,
1N & Thrust = FR = m f V f = (70 kg/s)(1500 m/s) 2 1 kg m/s = 105,000 N Therefore, if this spacecraft were attached somewhere, it would exert a force of 105,000 N (equivalent to the weight of 10,700 kg of mass on earth) to its support in the negative x direction.
Discussion In Part (b) we approximate the deceleration as constant. However, since mass is lost from the spacecraft during the time in which the jet is on, a more accurate solution would involve solving a differential equation. Here, the time span is short, and the lost mass is likely negligible compared to the total mass of the spacecraft, so the more complicated analysis is not necessary.
6-56
Chapter 6 Momentum Analysis of Flow Systems 6-73 Solution A horizontal water jet strikes a vertical stationary flat plate normally at a specified velocity. For a given flow velocity, the anchoring force needed to hold the plate in place is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water splatters off the sides of the plate in a plane normal to the jet. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water is the atmospheric pressure which is disregarded since it acts on the entire control surface. 4 The vertical forces and momentum fluxes are not considered since they have no effect on the horizontal reaction force. 5 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
We take the plate as the control volume such that it contains the entire plate and cuts through the water jet Analysis and the support bar normally, and the direction of flow as the positive direction of x axis. We take the reaction force to be in the negative x direction. The momentum equation for steady one-dimensional flow in the x (flow) direction reduces in this case to r r r & & & & FRx = i miVi F= mV mV FRx = i mV
out
in
We note that the reaction force acts in the opposite direction to flow, and we should not forget the negative sign for forces and velocities in the negative x-direction. The mass flow rate of water is
D (0.06 m) & (25 m/s) = 70.6858 kg/s m = V& = AV = V = (1000 kg/m3 ) 4 4

2 2
25 m/s
Substituting, the reaction force is determined to be
FRx
6 cm
FRx = (1) (70.6858 kg/s)(25 m/s) = 1767 N 1770 N

Therefore, a force of approximately 1770 N must be applied to the plate in the opposite direction to the flow to hold it in place.
Discussion In reality, some water may be scattered back, and this would add to the reaction force of water. If we do not approximate the water jet as uniform, the momentum flux correction factor would factor in. For example, if = 1.03 (approximate value for fully developed pipe flow), the force would increase by 3%. This is because the actual nonuniform jet has more momentum than the uniform jet.
6-57
Chapter 6 Momentum Analysis of Flow Systems 6-74 Solution A water jet hits a stationary cone, such that the flow is diverted equally in all directions at 45. The force required to hold the cone in place against the water stream is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The water jet is exposed to the atmosphere, and thus the pressure of the water jet before and after the split is the atmospheric pressure which is disregarded since it acts on all surfaces. 3 The gravitational effects are disregarded. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties Analysis
We take the density of water to be 1000 kg/m3. The mass flow rate of water jet is
(0.05 m) D & m = V& = AV = V = (1000 kg/m 3 ) (30 m/s) = 58.90 kg/s 4 4

We take the diverting section of water jet, including the cone as the control volume, and designate the entrance by 1 and the outlet after divergence by 2. We also designate the horizontal coordinate by x with the direction of flow as being the positive direction and the vertical coordinate by y. r r r & & F= mV mV . We let the x- and y-components The momentum equation for steady one-dimensional flow is
out
in
of the anchoring force of the cone be FRx and FRy, and assume them to be in the positive directions. Noting that V2 = V1 = V & & & and m 2 = m1 = m , the momentum equations along the x and y axes become
& & & FRx = mV 2 cos mV1 = mV (cos 1)
FRy = 0 (because of symmetry about x axis)

Substituting the given values,
1N FRx = (58.90 kg/s)(30 m/s)(cos45 - 1) 1 kg m/s 2 = 518 N FRy = 0
30 m/s
FRx
5 cm
The negative value for FRx indicates that the assumed direction is wrong, and should be reversed. Therefore, a force of 518 N must be applied to the cone in the opposite direction to flow to hold it in place. No holding force is necessary in the vertical direction due to symmetry and neglecting gravitational effects.
Discussion In reality, the gravitational effects will cause the upper part of flow to slow down and the lower part to speed up after the split. But for short distances, these effects are negligible.
6-58
Chapter 6 Momentum Analysis of Flow Systems 6-75 Solution Water is flowing into and discharging from a pipe U-section with a secondary discharge section normal to return flow. Net x- and z- forces at the two flanges that connect the pipes are to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The weight of the U-turn and the water in it is negligible. 4 The momentum-flux correction factor for each inlet and outlet is given to be = 1.03. Properties Analysis
V1 = V2 = V3 = We take the density of water to be 1000 kg/m3. The flow velocities of the 3 streams are
10 kg/s
2
32 kg/s
& & m1 m1 42 kg/s = = = 21.39 m/s 2 A1 (D1 / 4) (1000 kg/m 3 )[ (0.05 m) 2 / 4] & & m2 m2 32 kg/s = = = 4.074 m/s 2 A2 (D2 / 4) (1000 kg/m 3 )[ (0.10 m) 2 / 4]
FRz
1
42 kg/s
FRx
& & m3 m3 10 kg/s = = = 14.15 m/s 2 A3 (D3 / 4) (1000 kg/m 3 )[ (0.03 m) 2 / 4]
We take the entire U-section as the control volume. We designate the horizontal coordinate by x with the direction of incoming flow as being the positive direction and the vertical coordinate by z. The momentum equation for steady oner r r & & dimensional flow is F= mV mV . We let the x- and z-components of the anchoring force of the cone be FRx
out
in
and FRz, and assume them to be in the positive directions. Then the momentum equations along the x and z axes become
& & & & FRx + P1 A1 + P2 A2 = m 2 (V 2 ) m1V1 FRx = P1 A1 P2 A2 (m 2V 2 + m1V1 ) & & FRz + 0 = m 3V3 - 0 FRz = m 3V3
Substituting the given values,
FRx = [(200 100) kN/m 2 ]
(0.05 m) 2
4 1 kN 1.03(32 kg/s)(4.074 m/s) 1000 kg m/s 2 = 1.649 kN 1650 N
[(150 100) kN/m 2 ]
(0.10 m) 2
4
1 kN + (42 kg/s)(21.39 m/s) 1000 kg m/s 2
1N FRz = 1.03(10 kg/s)(14.15 m/s) 1 kg m/s 2 = 145.7 N 146 N The negative value for FRx indicates the assumed direction is wrong, and should be reversed. Therefore, a force of 1650 N acts on the flanges in the opposite direction. A vertical force of 146 N acts on the flange in the vertical direction.
Discussion To assess the significance of gravity forces, we estimate the weight of the weight of water in the U-turn and compare it to the vertical force. Assuming the length of the U-turn to be 0.5 m and the average diameter to be 7.5 cm, the mass of the water becomes
m = V = AL =
D 2
4
L = (1000 kg/m 3 )
(0.075 m) 2
4
(0.5 m) = 2.2 kg
whose weight is 2.29.81 = 22 N, which is much less than 146, but still significant. Therefore, disregarding the gravitational effects is a reasonable assumption if great accuracy is not required.
6-59
Chapter 6 Momentum Analysis of Flow Systems 6-76 Solution Indiana Jones is to ascend a building by building a platform, and mounting four water nozzles pointing down at each corner. The minimum water jet velocity needed to raise the system, the time it will take to rise to the top of the building and the velocity of the system at that moment, the additional rise when the water is shut off, and the time he has to jump from the platform to the roof are to be determined.
Assumptions 1 The air resistance is negligible. 2 The flow of water is steady and one-dimensional (but the motion of platform is unsteady). 3 The platform is still initially at t = 0. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Properties Analysis
We take the density of water to be 1000 kg/m3. (a) The total mass flow rate of water through the 4 hoses and the total weight of the platform are
& m = AV = 4
D2
4
V = 4(1000 kg/m3 )
(0.04 m) 2
4
(18 m/s) = 90.4779 kg/s
1N W = mg = (150 kg)(9.81 m/s 2 ) = 1471.5 N 2 1 kg m/s
r F=
out
We take the platform as the system. The momentum equation for steady one-dimensional flow is r r & & mV mV . The minimum water jet velocity needed to raise the platform is determined by setting the net
in
force acting on the platform equal to zero,
& W = m(V min ) 0
& W = mV min = AV min V min = 4
D 2
4
2 V min
Solving for Vmin and substituting,

Vmin = 1kg m/s 2 W 1471.5 N = = 17.1098 m/s 17.1 m/s D 2 (1000 kg/m3 ) (0.04 m) 2 1N
(b) We let the vertical reaction force (assumed upwards) acting on the platform be FRz. Then the momentum equation in the vertical direction becomes kg m 1kg m/s 2 & & & FRz W = m(V ) 0 = mV FRz = W mV = (1471.5 N) (90.4779 )(18 ) = 157.101 N s s 1N The upward thrust acting on the platform is equal and opposite to this reaction force, and thus F = 157.1 N. Then the acceleration and the ascending time to rise 10 m and the velocity at that moment become
a=
F 157.101 N 1 kg m/s 2 2 = = 1.0473 m/s m 150 kg 1 N
z x
FRy
x = 1 at 2 2
and
2x 2(10 m) t= = = 4.36989 s 4.37 s a 1.0473 m/s 2
V = at = (1.0473 m/s 2 )(4.36989 s) = 4.5766 m/s

(c) When the water is shut off at 10 m height (where the velocity is 4.57 m/s), the platform will decelerate under the influence of gravity, and the time it takes to come to a stop and the additional rise above 10 m become
D = 4 cm
18 m/s
V = V0 gt = 0
t=
V0 4.5766 m/s = = 0.46652 s g 9.81 m/s 2
z = V0 t 1 gt 2 = (4.5766 m/s)(0.46652 s) 1 (9.81 m/s 2 )(0.46652 s) 2 = 1.0675 m 1.07 m 2 2

Therefore, Jones has 2 0.46652 = 0.93304 0.933 s to jump off from the platform to the roof since it takes another 0.466 s for the platform to descend to the 10 m level.
Discussion
Like most stunts in the Indiana Jones movies, this would not be practical in reality. 6-60
Chapter 6 Momentum Analysis of Flow Systems 6-77 Solution A box-enclosed fan is faced down so the air blast is directed downwards, and it is to be hovered by increasing the blade rpm. The required blade rpm, air outlet velocity, the volumetric flow rate, and the minimum mechanical power are to be determined.
Assumptions 1 The flow of air is steady and incompressible. 2 The air leaves the blades at a uniform velocity at atmospheric pressure, and thus the momentum-flux correction factor can be taken to be unity, 1. 3 Air approaches the blades from the top through a large area at atmospheric pressure with negligible velocity. 4 The frictional effects are negligible, and thus the entire mechanical power input is converted to kinetic energy of air (no conversion to thermal energy through frictional effects). 5 The change in air pressure with elevation is negligible because of the low density of air. 6 There is no acceleration of the fan, and thus the lift generated is equal to the total weight. Properties
(a) We take the control volume to be a vertical hyperbolic cylinder bounded by streamlines on the sides Analysis with air entering through the large cross-section (section 1) at the top and the fan located at the narrow cross-section at the bottom (section 2), and let its centerline be the z axis with upwards being the positive direction. r r r & & The momentum equation for steady one-dimensional flow is F= mV mV . Noting that the only
out
in
force acting on the control volume is the total weight W and it acts in the negative z direction, the momentum equation along the z axis gives
& W = m(V 2 ) 0
where A is the blade span area,
& W = mV 2 = ( AV 2 )V 2 = AV 22
V2 =
A = D 2 / 4 = (0.9 m) 2 / 4 = 0.6362 m 2
Then the discharge velocity to produce 22 N of upward force becomes V2 = 1 kg m/s 2 1N (1.25 kg/m )(0.6362 m ) 22 N
3 2
FRy
= 5.26 m/s
600 rpm
(b) The volume flow rate and the mass flow rate of air are determined from their definitions, & V = AV = (0.6362 m 2 )(5.26 m/s) = 3.35 m 3 /s
2
& & m = V = (1.25 kg/m 3 )(3.35 m 3 /s) = 4.19 kg/s
(c) Noting that P1 = P2 = Patm, V1 0, the elevation effects are negligible, and the frictional effects are disregarded, the energy equation for the selected control volume reduces to
P V2 P V2 & & & & & m 1 + 1 + gz1 + W pump, u = m 2 + 2 + gz 2 + W turbine + E mech,loss 2 2 Substituting,
V (5.26 m/s) & & Wfan,u = m 2 = (4.19 kg/s) 2 2
2 2
V & & Wfan, u = m 2 2
1 W 1N 1 kg m/s 2 1 N m/s = 57.9 W Therefore, the minimum mechanical power that must be supplied to the air stream is 57.9 W.
Discussion The actual power input to the fan will be considerably larger than the calculated power input because of the fan inefficiency in converting mechanical work to kinetic energy.
6-61
Chapter 6 Momentum Analysis of Flow Systems 6-78 Solution The rocket of a satellite is fired in the opposite direction to motion. The thrust exerted on the satellite, the acceleration, and the velocity change are to be determined.
Assumptions 1 The flow of combustion gases is steady and one-dimensional during the firing period, but the motion of the satellite is unsteady. 2 There are no external forces acting on the spacecraft, and the effect of pressure force at the nozzle outlet is negligible. 3 The mass of discharged fuel is negligible relative to the mass of the spacecraft, and thus, the spacecraft may be treated as a solid body with a constant mass. 4 The nozzle is well designed such that the effect of the momentum-flux correction factor is negligible, and thus 1. Analysis (a) For convenience, we choose an inertial reference frame that moves with the satellite at the same initial velocity. Then the velocities of fluid stream relative to an inertial reference frame become simply the velocities relative to the satellite. We take the direction of motion of the satellite as the positive direction along the x-axis. There are no external forces acting on the satellite, and its mass is essentially constant. Therefore, the satellite can be treated as a solid body with constant mass, and the momentum equation in this case is
r r Fthrust = m satellite a satellite =

The fuel discharge rate is
& & mV mV
in out
& mf =
mf t
100 kg = 50 kg/s 2s
= 150 kN
Then the thrust exerted on the satellite in the positive x direction becomes
1 kN & Fthrust = 0 m f V f = (50 kg/s )(3000 m/s ) 1000 kg m/s 2
(b) Noting that the net force acting on the satellite is thrust, the acceleration of the satellite in the direction of thrust during the first 2 s is determined to be
asatellite =
Fthrust 150 kN 1000 kg m/s 2 = msatellite 5000 kg 1 kN
= 30 m/s 2
(c) Knowing acceleration, which is constant, the velocity change of the satellite during the first 2 s is determined from the definition of acceleration a satellite = dVsatellite / dt ,
Vsatellite = a satellite t = (30 m/s 2 )( 2 s) = 60 m/s

Discussion Note that if this satellite were attached somewhere, it would exert a force of 150 kN (equivalent to the weight of 15 tons of mass) to its support. This can be verified by taking the satellite as the system and applying the momentum equation.
6-62
Chapter 6 Momentum Analysis of Flow Systems 6-79 Solution A walnut is to be cracked by dropping it from a certain height to a hard surface. The minimum height required is to be determined.
Assumptions Analysis
1 The force remains constant during the cracking period of the walnut. 2 The air resistance is negligible. We take the x axis as the upward vertical direction. Newtons 2nd law F = ma = mdV/dt can be expressed as
Ft = mV = m(Vstrike Vfinal )
Vstrike =
Ft m
m V
h
since the force remains constant and the final velocity is zero. Substituting, Vstrike = Ft (200 N)(0.002 s) 1 kg m/s 2 = 0.050 kg 1N m = 8 m/s
The elevation that will result at this value of velocity can be determined from the conservation of energy principle (in this case potential energy being converted to kinetic energy) to be pe initial = kefinal
2 mgh = 1 mVstrike 2
h=
2 Vstrike 2g
Substituting, the required height at which the walnut needs to be dropped becomes
h=
2 3 . 2 6 m Vstrike (8 m/s) 2 = = 2 2g 2(9.81 m/s )
Discussion
Note that a greater height will be required in reality because of air friction.
6-63
Chapter 6 Momentum Analysis of Flow Systems 6-80 Solution A vertical water jet strikes a horizontal stationary plate normally. The maximum weight of the plate that can be supported by the water jet at a specified height is to be determined.
Assumptions 1 The flow of water at the nozzle outlet is steady and incompressible. 2 The water splatters in directions normal to the approach direction of the water jet. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water leaving the control volume is atmospheric pressure. 4 Friction between the water and air is negligible. 5 The effect of the momentum-flux correction factor is negligible, and thus 1 for the jet. Properties
Analysis We take the x axis as the upward vertical direction. We also take point 1 at the point where the water jet leaves the nozzle, and point 2 at the point where the jet strikes the flat plate. Noting that water jet is exposed to the atmosphere, we have P1 = P2 = Patm , Also, z1 = 0 and z2 = h. Then the Bernoulli Equation simplifies to
P V12 P V2 1 + + z1 = 2 + 2 + z2 g 2 g g 2 g 0+ V12 V2 +0 = 0+ 2 +h 2g 2g V2 = V12 2 gh
W 2 V2
h
Substituting, the jet velocity when the jet strikes the flat plate is determined to be
V2 = (15 m/s )2 2(9.81 m/s 2 )(2 m ) = 13.63 m/s
The mass flow rate of water is
(0.07 m) D & & m = V = AcV = V = (1000 kg/m 3 ) (15 m/s) = 57.73 kg/s 4 4
We take the thin region below the flat plate as the control volume such that it cuts through the incoming water jet. The weight W of the flat plate acts downward as a vertical force on the CV. Noting that water jet splashes out horizontally after it strikes the plate, the momentum equation for steady one-dimensional flow in the x (flow) direction reduces to r r r & & & & W = mV 2 W = mV 2 F= mV mV
out
in
Substituting, the weight of the flat plate is determined to be 1N W = (57.73 kg/s)(13.36 m/s) 1 kg m/s 2 = 771 N Note that this weight corresponds to a plate mass of 771/9.81 = 78.5 kg of mass. Also, a smaller mass will Discussion be held in balance at a greater height and a larger mass at a smaller height.
6-64
Chapter 6 Momentum Analysis of Flow Systems 6-81 Solution A vertical water jet strikes a horizontal stationary plate normally. The maximum weight of the plate that can be supported by the water jet at a specified height is to be determined.
Assumptions 1 The flow of water at the nozzle outlet is steady and incompressible. 2 The water splatters in directions normal to the approach direction of the water jet. 3 The water jet is exposed to the atmosphere, and thus the pressure of the water jet and the splattered water leaving the control volume is atmospheric pressure. 4 Friction between the water and air is negligible. 5 The effect of the momentum-flux correction factor is negligible, and thus 1 for the jet. Properties
Analysis We take the x axis as the upward vertical direction. We also take point 1 at the point where the water jet leaves the nozzle, and point 2 at the point where the jet strikes the flat plate. Noting that water jet is exposed to the atmosphere, we have P1 = P2 = Patm , Also, z1 = 0 and z2 = h. Then the Bernoulli Equation simplifies to
P V2 P V12 1 + + z1 = 2 + 2 + z2 g 2 g g 2 g 0+ V12 V2 +0 = 0+ 2 +h 2g 2g V2 = V12 2 gh
W 2 V2
h
Substituting, the jet velocity when the jet strikes the flat plate is determined to be
V2 = (15 m/s ) 2 2(9.81 m/s 2 )(5 m ) = 11.26 m/s
The mass flow rate of water is
(0.07 m) D & & m = V = AcV = V = (1000 kg/m 3 ) (15 m/s) = 57.73 kg/s 4 4
We take the thin region below the flat plate as the control volume such that it cuts through the incoming water jet. The weight W of the flat plate acts downward as a vertical force on the CV. Noting that water jet splashes out horizontally after it strikes the plate, the momentum equation for steady one-dimensional flow in the x (flow) direction reduces to r r r & & & & W = mV 2 W = mV 2 F= mV mV
out
in
Substituting, the weight of the flat plate is determined to be 1N W = (57.73 kg/s)(11.26 m/s) 1 kg m/s 2 = 650 N Note that this weight corresponds to a plate mass of 650/9.81 = 66.3 kg of mass. Also, a smaller mass will Discussion be held in balance at a greater height and a larger mass at a smaller height.
6-65
Chapter 6 Momentum Analysis of Flow Systems 6-82 Solution Steady developing laminar flow is considered in a constant horizontal diameter discharge pipe. A relation is to be obtained for the horizontal force acting on the bolts that hold the pipe.
Assumptions 1 The flow is steady, laminar, and incompressible. 2 The flow is fully developed at the end of the pipe section considered. 3 The velocity profile at the pipe inlet is uniform and thus the momentum-flux correction factor is 1 = 1. 4 The momentum-flux correction factor is = 2 at the outlet. Analysis We take the developing flow section of the pipe (including the water inside) as the control volume. We assume the reaction force to act in the positive direction. Noting that the flow is incompressible and thus the average velocity is constant V1 = V2 = V, the momentum equation for steady one-dimensional flow in the z (flow) direction in this case reduces to
& & F = mV mV
out in
& & FR + P1 Ac P2 Ac = m 2V m 1V & V (1 2 ) FR = ( P1 P2 ) Ac + m & = ( P1 P2 ) Ac + mV (1 2)

& = ( P1 P2 )D 2 / 4 mV
Or, using the definition of the mass flow rate, FR = ( P1 P2 )D 2 / 4 [ D 2 / 4]V 2 Or, FR =
D 2
4
[( P P ) V ]
1 2 2
Discussion
Note that the cause of this reaction force is non-uniform velocity profile at the end.
6-66
Chapter 6 Momentum Analysis of Flow Systems 6-83 Solution A parachute slows a soldier from his terminal velocity VT to his landing velocity of VF. A relation is to be developed for the soldiers velocity after he opens the parachute at time t = 0.
Assumptions 1 The air resistance is proportional to the velocity squared (i.e. F = kV2). 2 The variation of the air properties with altitude is negligible. 3 The buoyancy force applied by air to the person (and the parachute) is negligible because of the small volume occupied and the low density of air. 4 The final velocity of the soldier is equal to its terminal velocity with his parachute open. Analysis The terminal velocity of a free falling object is reached when the air resistance (or air drag) equals the weight of the object, less the buoyancy force applied by the fluid, which is negligible in this case, mg 2 Fair resistance = W kV F = mg k= 2 VF This is the desired relation for the constant of proportionality k. When the parachute is deployed and the soldier starts to decelerate, the net downward force acting on him is his weight less the air resistance, V2 mg Fnet = W Fair resistance = mg kV 2 = mg 2 V 2 = mg 1 2 Fair resistance V VF F dV Substituting it into Newtons 2nd law relation Fnet = ma = m gives dt
V2 dV mg 1 2 = m V dt F Canceling m and separating variables, and integrating from t = 0 when V = VT to t = t when V = V gives dV 1V Using
2 2 / VF
= gdt =
dV V
2
VT V 2 F
g
2 VF
dt
Parachute
W = mg
x2 integration limits, 1 2V F
dx
2
1 a+x ln 2a a x
from integral tables and applying the
VF + V V F + VT ln V V ln V V F F T
gt = 2 V F
Rearranging, the velocity can be expressed explicitly as a function of time as V = VF VT + V F + (VT V F )e 2 gt / VF VT + V F (VT V F )e 2 gt / VF
Discussion
Note that as t , the velocity approaches the landing velocity of VF, as expected.
6-67
Chapter 6 Momentum Analysis of Flow Systems 6-84 Solution An empty cart is to be driven by a horizontal water jet that enters from a hole at the rear of the cart. A relation is to be developed for cart velocity versus time.
Assumptions 1 The flow of water is steady, one-dimensional, incompressible, and horizontal. 2 All the water which enters the cart is retained. 3 The path of the cart is level and frictionless. 4 The cart is initially empty and stationary, and thus V = 0 at time t = 0. 5 Friction between water jet and air is negligible, and the entire momentum of water jet is used to drive the cart with no losses. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Analysis We note that the water jet velocity VJ is constant, but the car velocity V is variable. Noting that & m = A(V J V ) where A is the cross-sectional area of the water jet and VJ - V is the velocity of the water jet relative to the cart, the mass of water in the cart at any time t is Cart t t t & m w = mdt = A(V J V ) dt = AV J t A Vdt (1) m0
Also, dm w & = m = A(V J V ) dt

Waterjet
We take the cart as the moving control volume. The net force acting on the cart in this case is equal to the momentum flux of the water jet. Newtons 2nd law F = ma = d(mV)/dt in this case can be expressed as
F= d ( m total V ) dt
where
F=
& & & mV mV = (mV )

in out
in
& = mVJ = A(VJ V )VJ
and
d (m total V ) d [(m c + m w )V ] dm w dV d ( m wV ) dV dV = = mc + = mc + mw +V dt dt dt dt dt dt dt dV = (m c + m w ) + A(V J V )V dt
& Note that in mV expressions, we used the fluid stream velocity relative to a fixed point. Substituting,
A(VJ V )VJ = (mc + mw )
dV + A(VJ V )V dt
A(VJ V )(VJ V ) = (mc + mw )
dV dt
Noting that mw is a function of t (as given by Eq. 1) and separating variables, dV dt = 2 mc + mw A(VJ V ) dV dt = 2 t A(VJ V ) mc + AVJ t A Vdt
Integrating from t = 0 when V = 0 to t = t when V = V gives the desired integral,
V 0
dV = A(VJ V ) 2
t o
dt mc + AVJ t A Vdt
0
Discussion
Note that the time integral involves the integral of velocity, which complicates the solution.
6-68
Chapter 6 Momentum Analysis of Flow Systems 6-85 Solution Water enters the impeller of a turbine through its outer edge of diameter D with velocity V making an angle & with the radial direction at a mass flow rate of m , and leaves the impeller in the radial direction. The maximum power & && that can be generated is to be shown to be Wshaft = nmDV sin .
Assumptions negligible.
1 The flow is steady in the mean. 2 Irreversible losses are
r2 =D/2
r V
Analysis We take the impeller region as the control volume. The tangential velocity components at the inlet and the outlet are V1,t = 0 and
V 2,t = V sin .
r V
Normal velocity components as well pressure acting on the inner and outer circumferential areas pass through the shaft center, and thus they do not contribute to torque. Only the tangential velocity components contribute to torque, and the application of the angular momentum equation gives & & & Tshaft = m(r2V 2,t r1V1,t ) = mr2V 2,t 0 = mD(V sin ) / 2
& The angular velocity of the propeller is = 2n . Then the shaft power becomes & && Wshaft = Tshaft = 2nmD (V sin ) / 2
Tshaft
Impeller region
& && Simplifying, the maximum power generated becomes Wshaft = nmDV sin which is the desired relation.
Discussion
The actual power is less than this due to irreversible losses that are not taken into account in our analysis.
6-69
Chapter 6 Momentum Analysis of Flow Systems 6-86 Solution A two-armed sprinkler is used to water a garden. For specified flow rate and discharge angles, the rates of rotation of the sprinkler head are to be determined.
r = 0.52 m
Analysis We take the disk that encloses the sprinkler arms as the control volume, which is a stationary control volume. The conservation & & & of mass equation for this steady flow system is m1 = m 2 = m . Noting & & that the two nozzles are identical, we have m nozzle = m / 2 or / 2 since the density of water is constant. The average V& = V&
nozzle total
jet outlet velocity relative to the nozzle is

V jet =
V&nozzle
Ajet
1 m3 = 119.4 m/s 2[ (0.02 m) 2 / 4] 1000 L
75 L/s
The angular momentum equation can be expressed as
& & M = rmV rmV . Noting that there are no external

out in
moments acting, the angular momentum equation about the axis of rotation becomes
& 0 = 2rm nozzleV r cos
Vr = 0
V jet,t V nozzle = 0
Noting that the tangential component of jet velocity is V jet,t = V jet cos , we have
Vnozzle = V jet cos = (119.4 m/s)cos
& Also noting that V nozzle = r = 2nr , and angular speed and the rate of rotation of sprinkler head become
1) = 0: =
Vnozzle (119.4 m/s)cos0 = = 230 rad/s r 0.52 m
and
& n=
230 rad/s 60 s = 2193 rpm 2 1 min
2) = 30: = 3) = 60: =
Vnozzle (119.4 m/s)cos30 199 rad/s 60 s & = = 199 rad/s and n = = = 1899 rpm r 0.52 m 2 2 1 min Vnozzle (119.4 m/s)cos60 115 rad/s 60 s & = = 115 rad/s and n = = = 1096 rpm r 0.52 m 2 2 1 min
Discussion Final results are given to three significant digits, as usual. The rate of rotation in reality will be lower because of frictional effects and air drag.
6-70
Chapter 6 Momentum Analysis of Flow Systems 6-87 & Solution The previous problem is reconsidered. The effect of discharge angle on the rate of rotation n as varies from 0 to 90 in increments of 10 is to be investigated.
Analysis
D=0.02 "m" r=0.45 "m" n_nozzle=2 "number of nozzles" Ac=pi*D^2/4 V_jet=V_dot/Ac/n_nozzle V_nozzle=V_jet*cos(theta) V_dot=0.060 "m3/s" omega=V_nozzle/r n_dot=omega*60/(2*pi) Angle, 0 10 20 30 40 50 60 70 80 90
2250
Vnozzle, m/s 95.5 94.0 89.7 82.7 73.2 61.4 47.7 32.7 16.6 0.0
rad/s 212 209 199 184 163 136 106 73 37 0
& n rpm 2026 1996 1904 1755 1552 1303 1013 693 352 0
1800
n, rpm
1350
900
450
0 0
10
20
30
40
50
60
70
80
90
Discussion The maximum rpm occurs when = 0o, as expected, since this represents purely tangential outflow. When o = 90 , the rpm drops to zero, as also expected, since the outflow is purely radial and therefore there is no torque to spin the sprinkler.
6-71
Chapter 6 Momentum Analysis of Flow Systems 6-88 Solution A stationary water tank placed on wheels on a frictionless surface is propelled by a water jet that leaves the tank through a smooth hole. Relations are to be developed for the acceleration, the velocity, and the distance traveled by the tank as a function of time as water discharges.
Assumptions 1 The orifice has a smooth entrance, and thus the frictional losses are negligible. 2 The flow is steady, incompressible, and irrotational (so that the Bernoulli equation is applicable). 3 The surface under the wheeled tank is level and frictionless. 4 The water jet is discharged horizontally and rearward. 5 The mass of the tank and wheel assembly is negligible compared to the mass of water in the tank. 4 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1.
(a) We take point 1 at the free surface of the tank, and point 2 at Analysis the outlet of the hole, which is also taken to be the reference level (z2 = 0) so that the water height above the hole at any time is z. Noting that the fluid velocity at the free surface is very low (V1 0), it is open to the atmosphere (P1 = Patm), and water discharges into the atmosphere (and thus P2 = Patm), the Bernoulli equation simplifies to P V12 P V2 V2 1 + + z1 = 2 + 2 + z2 z = J + 0 VJ = 2 gz 2g g 2 g g 2 g The discharge rate of water from the tank through the hole is
& m = AV J =
2 D0 2 D0
z x
D0
VJ
VJ =
2 gz
& & F = mV mV . Applying it to the water tank,
out in
The momentum equation for steady one-dimensional flow is the horizontal force that acts on the tank is determined to be
4 2 The acceleration of the water tank is determined from Newtons 2nd law of motion F = ma where m is the mass of water in the tank, m = V tank = (D 2 / 4 ) z ,
a=
2 F gz ( D0 / 2 ) = m z ( D 2 / 4 )
& & F = mVe 0 = mV J =
2 D0
2 gz = gz
2 D0
a = 2g
D02 D2
Note that the acceleration of the tank is constant. (b) Noting that a = dV/dt and thus dV = adt and acceleration a is constant, the velocity is expressed as V = at V = 2g D02 t D2
(c) Noting that V = dx/dt and thus dx = Vdt, the distance traveled by the water tank is determined by integration to be dx = Vdt since x = 0 at t = 0.
Discussion In reality, the flow rate discharge velocity and thus the force acting on the water tank will be less because of the frictional losses at the hole. But these losses can be accounted for by incorporating a discharge coefficient.
dx = 2 g
D02 tdt D2
x=g
D02 2 t D2
6-72
Chapter 6 Momentum Analysis of Flow Systems 6-89 Solution A plate is maintained in a horizontal position by frictionless vertical guide rails. The underside of the plate & is subjected to a water jet. The minimum mass flow rate m min to just levitate the plate is to be determined, and a relation is to be obtained for the steady state upward velocity. Also, the integral that relates velocity to time when the water is first turned on is to be obtained.
Assumptions 1 The flow of water is steady and one-dimensional. 2 The water jet splatters in the plane of the plate. 3 The vertical guide rails are frictionless. 4 Times are short, so the velocity of the rising jet can be considered to remain constant with height. 5 At time t = 0, the plate is at rest. 6 Jet flow is nearly uniform and thus the momentum-flux correction factor can be taken to be unity, 1. Analysis r F=
out
& mV
(a) We take the plate as the system. The momentum equation for steady one-dimensional flow is r r & & mV . Noting that m = AV J where A is the cross-sectional area of the water jet and W = mpg, the
in
minimum mass flow rate of water needed to raise the plate is determined by setting the net force acting on the plate equal to zero,
& W = 0 m minV J
& W = m minV J
& & m p g = m min (m min / AV J )
& m min = Am p g
& & For m > m min , a relation for the steady state upward velocity V is obtained setting the upward impulse applied by water jet to the weight of the plate (during steady motion, the plate velocity V is constant, and the velocity of water jet relative to plate is VJ V), & W = m(V J V )
m p g = A(V J V ) 2 VJ V = mp g
V= FRz
mpg & m A A
(b) At time t = 0, the plate is at rest (V = 0), and it is subjected to water & & jet with m > m min and thus the net force acting on it is greater than the weight of the plate, and the difference between the jet impulse and the weight will accelerate the plate upwards. Therefore, Newtons 2nd law F = ma = mdV/dt in this case can be expressed as
Guide rails
W = mp g mp
& m(V J V ) W = m p a
dV A(V J V ) 2 m p g = m p dt
. m
Separating the variables and integrating from t = 0 when V = 0 to t = t when V = V gives the desired integral,
V 0
m p dV
A(VJ V ) m p g
2
t t =0
dt
t=
V 0
m p dV
A(VJ V )2 m p g
Nozzle
Discussion V.
This integral can be performed with the help of integral tables. But the relation obtained will be implicit in
6-73
Chapter 6 Momentum Analysis of Flow Systems 6-90 Solution Water enters a centrifugal pump axially at a specified rate and velocity, and leaves at an angle from the axial direction. The force acting on the shaft in the axial direction is to be determined.
Assumptions 1 The flow is steady and incompressible. 2 The forces acting on the piping system in the horizontal direction are negligible. 3 The atmospheric pressure is disregarded since it acts on all surfaces. 4 Water flow is nearly uniform at the outlet and thus the momentum-flux correction factor can be taken to be unity, 1. Properties
z x
75
& & & Analysis From conservation of mass we have m1 = m 2 = m , and thus V&1 = V&2 and Ac1V1 = Ac 2V 2 . Noting that the discharge area is half the inlet area, the discharge velocity is twice the inlet velocity. That is, A Ac1V2 = c1 V1 = 2V1 = 2(7 m/s) = 14 m/s Ac 2
& mV
We take the pump as the control volume, and the inlet direction of flow as the positive direction of x axis. The linear momentum equation in this case in the x direction reduces to r r r & & & & F= mV mV FRx = mV2 cos mV1
n &
FRx
out
in
& FRx = m(V1 V2 cos )
where the mass flow rate it & m = V& = (1000 kg/m 3 )(0.30 m 3 /s) = 300 kg/s Substituting the known quantities, the reaction force is determined to be
1N FRx = (300 kg/s)[(7 m/s) (14 m/s)cos75] 1 kg m/s 2 = 1013 N
Note that at this angle of discharge, the bearing is not subjected to any horizontal loading. Therefore, the Discussion loading in the system can be controlled by adjusting the discharge angle.
Design and Essay Problem
6-91 Solution
Students essays and designs should be unique and will differ from each other.
6-74

SI FM 2e SM Chap06

Uploaded by

Copyright:

Available Formats

SI FM 2e SM Chap06

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SI FM 2e SM Chap06

Uploaded by

Copyright:

Available Formats

Chapter 6 Momentum Analysis of Flow Systems

Solutions Manual for

Fluid Mechanics: Fundamentals and Applications SI Edition

CHAPTER 6 MOMENTUM ANALYSIS OF FLOW SYSTEMS

We are to discuss the conservation of momentum principle.

We are to express Newtons three laws.

We are to discuss Newtons second law for rotating bodies.

Chapter 6 Momentum Analysis of Flow Systems Linear Momentum Equation

We are to describe and discuss body forces and surface forces.

We are to discuss surface forces in a control volume analysis.

6-7C Solution Analysis

We are to describe how a helicopter can hover.

Chapter 6 Momentum Analysis of Flow Systems 6-13C Solution

and thus the force is proportional to the square of the velocity.

We are to compare the reaction force on two fire hoses.

We are to discuss the acceleration of a cart hit by a water jet.

Stationary plate: ( Vi = V and

(b) The momentum equation for steady one-dimensional flow is

We let the x- and z-

1N & FRy = mV = 1.03(30 kg/s)(3.820 m/s) 1 kg m/s 2

2 2 FR = FRx + FRy = (148.9) 2 + (118.0) 2 = 190 N,

118.0 = 38.4 = 142 148.9

We take the density of water to be 1000 kg/m3.

(b) The momentum equation for steady one-dimensional flow is

We let the x- and z-

FRz = 0 Solving for FRx and substituting the given values,

W = mg = (50 kg)(9.81 m/s 2 ) = 490.5 N = 0.4905 kN

& & FRx + P1,gage A1 = mV 2 cos mV1

& FRy W = mV 2 sin

1 kN = 1.03(30 kg/s)[(12cos110 - 2) m/s] 1000 kg m/s 2 FRz

2 2 FR = FRx + FRz = (1.297) 2 + 0.8389 2 = 1.54 kN

20 m/s 400 kg Waterjet

Chapter 6 Momentum Analysis of Flow Systems 6-26

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180

35000 30000 25000

20000 15000 10000 5000 0 0

Then the initial acceleration of the plate becomes

18 m/s 1000 kg Waterjet Frictionless track

(b) The momentum equation for steady one-dimensional flow is

& & F = mV mV . We let horizontal force

Chapter 6 Momentum Analysis of Flow Systems 6-31

10 00 800 600 400 200 0 0 5 10 15 20 Vplate, m /s 25 30

0.95 m3/s Fan 1 2 61 cm

& & 0.95 m 3 /s V V = = = 3.251 m/s 2 A2 D2 / 4 (0.61 m) 2 / 4

The momentum equation for steady one-dimensional flow is

& & F = mV mV . Letting the reaction force to hold

V & & Wfan, u = m 2 2

(10,000 kg)(9.81 m/s 2 ) (1.18 kg/m 3 )(254.5 m 2 )

Sea level Load 14,000 kg

V&unloaded = AV2,unloaded = (254.5 m 2 )(18.07 m/s) = 4600 m 3 /s

(24,000 kg)(9.81 m/s 2 ) (1.18 kg/m 3 )(254.5 m 2 )

1.18 kg/m3 = 1.1276 0.928 kg/m3

& nmountain V2,mountain = & nsea V2,sea

& nsea = 1.1276(400 rpm) = 451.052 rpm 451 rpm

P V2 P V2 & & & & & m 1 + 1 + gz1 + W pump, u = m 2 + 2 + gz 2 + W turbine + E mech,loss 2 2

V & & Wfan, u = m 2 2

1.18 kg/m 3 0.928 kg/m 3

Sea level Load 14,000 kg

V&1 = V&2 = V&