Mopx 205
Mopx 205
Mopx 205
Separator Manual
881034-01-08 1270366-02 V2
Alfa Laval Separation AB Separator Manuals, dept. SKL S-147 80 Tumba, Sweden Telephone: +46 8 53 06 50 00 Telefax: +46 8 53 06 50 29 Printed in Sweden, 96-10
Alfa Laval Separation AB 1996 This publication or any part thereof may not be reproduced or transmitted by any process or means without prior written permission of Alfa Laval Separation AB.
Contents
1 2 3 Read this first Safety Instructions Separator Basics
3.1 Basic principles of separation 3.2 Design and function 3.3 Separating function 3.4 Definitions 7 9 15 16 18 27 33 35 36 43 45 49 56 72 85 86 89 93 94 99 100 102 105 114 121
Operating Instructions
4.1 Operating routine
Service Instructions
5.1 Periodic maintenance 5.2 Maintenance Logs 5.3 Check points at Intermediate Service (IS) 5.4 Check points at Major Service (MS) 5.5 Lifting instructions 5.6 Cleaning 5.7 When changing oil 5.8 Vibration 5.9 Common maintenance directions
Dismantling/Assembly
6.1 Introduction 6.2 Inlet/outlet, frame hood (IS) 6.3 Bowl hood and disc stack (IS) 6.4 Bowl body and operating mechanism (IS) 6.5 Paring disc device for operating water (IS)
6.6 Vertical driving device (MS) 6.7 Horizontal driving device (MS) 6.8 Built-on oil feed pump
126 138 148 157 158 163 166 168 169 170 172 175 179 180 188 202 213
Trouble-tracing
7.1 Mechanical function 7.2 Separation faults, purifier and clarifier 7.3 Separation faults, purifier 7.4 Separation faults, clarifier
Technical Reference
8.1 Technical data 8.2 Connection list 8.3 Interface description 8.4 Water quality 8.5 Lubricants 8.6 Drawings 8.7 Storage and installation
Index
Study instruction manuals and observe the warnings before installation, operation, service and maintenance.
In order to make the information clear only foreseeable conditions have been considered. No warnings are given, therefore, for situations arising from the unintended usage of the machine and its tools.
This manual is designed for operators and service engineers working with the Alfa Laval separator MOPX 205 TGT-24. For information concerning the function of the separator, see chapter 3 Separator Basics on page 15 and chapter 8 Technical Reference on page 169. If the separator has been delivered and installed by Alfa Laval as part of a processing system, this manual is a part of the system documentation. In this case, study carefully all the instructions in the system documentation. In addition to this Separator Manual a Spare Parts Catalogue, SPC is supplied. This Separator Manual consists of:
Safety Instructions
Pay special attention to the safety instructions for the separator. Not following the safety instructions can cause accidents resulting in damage to equipment and serious injury to personnel.
Separator Basics
Read this chapter if you are not familiar with this type of separator.
Operating Instructions
This chapter contains operating instructions for the separator only.
S0068011
Service Instructions
This chapter gives instructions for daily checks, cleaning, oil changes, servicing and check points.
Dismantling / Assembly
This chapter contains step-by-step instructions for dismantling and assembly of the separator for service and repair.
Trouble-tracing
Refer to this chapter if the separator functions abnormally. If the separator has been installed as part of a processing system always refer to the Troubletracing part of the System Manual first.
Technical Reference
This chapter contains technical data concerning the separator and drawings.
Index
This chapter contains an alphabetical list of subjects, with page references.
2 Safety Instructions
The centrifugal separator includes parts that rotate at high speed. This means that: Kinetic energy is high Great forces are generated Stopping time is long
Manufacturing tolerances are extremely fine. Rotating parts are carefully balanced to reduce undesired vibrations that can cause a breakdown. Material properties have been considered carefully during design to withstand stress and fatigue. The separator is designed and supplied for a specific separation duty (type of liquid, rotational speed, temperature, density etc.) and must not be used for any other purpose. Incorrect operation and maintenance can result in unbalance due to build-up of sediment, reduction of material strength, etc., that subsequently could lead to serious damage and/or injury. The following basic safety instructions therefore apply: Use the separator only for the purpose and parameter range specified by Alfa Laval. Strictly follow the instructions for installation, operation and maintenance. Ensure that personnel are competent and have sufficient knowledge of maintenance and operation, especially concerning emergency stopping procedures. Use only Alfa Laval genuine spare parts and the special tools supplied.
G0010411
2 Safety Instructions
DANGER
Disintegration hazards Use the separator only for the purpose and parameter range specified by Alfa Laval. If excessive vibration occurs, stop separator and keep bowl filled with liquid during rundown. When power cables are connected, always check direction of motor rotation. If incorrect, vital rotating parts could unscrew. Check that the gear ratio is correct for power frequency used. If incorrect, subsequent overspeed may result in a serious break down. Welding or heating of parts that rotate can seriously affect material strength. Wear on the large lock ring thread must not exceed safety limit. -mark on lock ring must not pass opposite -mark by more than specified distance. Inspect regularly for corrosion and erosion damage. Inspect frequently if process liquid is corrosive or erosive.
m /h kPa kg/m
3
o
rpm Hz
S0051311 S0055611
10
2 Safety Instructions
DANGER
Entrapment hazards Make sure that rotating parts have come to a complete standstill before starting any dismantling work. To avoid accidental start, switch off and lock power supply before starting any dismantling work. Assemble the machine completely before start. All covers and guards must be in place.
S0051011 S0051611 S0051711
Electrical hazards Follow local regulations for electrical installation and earthing (grounding).
WARNING
Crush hazards Use correct lifting tools and follow lifting instructions. Do not work under a hanging load. Noise hazards Use ear protection in noisy environments.
11
S0051111
2 Safety Instructions
CAUTION
S0055411 S0054311
Burn hazards Lubrication oil and various machine surfaces can be hot and cause burns. Cut hazards Sharp edges on separator discs and lock ring threads can cause cuts.
12
2 Safety Instructions
DANGER
Type of hazard This type of safety instruction indicates a situation which, if not avoided, could result in fatal injury or fatal damage to health.
WARNING
Type of hazard This type of safety instruction indicates a situation which, if not avoided, could result in disabling injury or disabling damage to health.
CAUTION
Type of hazard This type of safety instruction indicates a situation which, if not avoided, could result in light injury or light damage to health.
NOTE
This type of instruction indicates a situation which, if not avoided, could result in damage to the equipment.
13
2 Safety Instructions
14
3 Separator Basics
Contents
3.1 Basic principles of separation 3.2 Design and function
3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 3.2.6 Application Overview Mechanical power transmission Sensors and indicators Inlet pump (option) Process main parts 16
18 18 19 20 21 22 24 27 27 29 30 31 33
3.4 Definitions
15
3 Separator Basics
3.1
The purpose of separation can be: to free a liquid of solid particles, to separate two mutually insoluble liquids with different densities while removing any solids presents at the same time, to separate and concentrate solid particles from a liquid.
Separation by gravity
A liquid mixture in a stationary bowl will clear slowly as the heavy particles in the liquid mixture sink to the bottom under the influence of gravity. A lighter liquid rises while a heavier liquid and solids sink. Continuous separation and sedimentation can be achieved in a settling tank having outlets arranged according to the difference in density of the liquids. Heavier particles in the liquid mixture will settle and form a sediment layer on the tank bottom.
Sedimentation by gravity
Centrifugal separation
In a rapidly rotating bowl, the force of gravity is replaced by centrifugal force, which can be thousands of times greater. Separation and sedimentation is continuous and happens very quickly. The centrifugal force in the separator bowl can achieve in a few seconds what takes many hours in a tank under influence of gravity.
Sedimentation in a settling tank, with outlets making it possible to separate the lighter liquid parts from the heavier
G0010811
G0010711
16
G0010911
3 Separator Basics
Separating temperatures
For some types of process liquids (e.g. mineral oils) a high separating temperature will normally increase the separation capacity. The temperature influences oil viscosity and density and should be kept constant throughout the separation.
Density difference The greater the density difference between the two liquids, the easier the separation. The density difference can be increased by heating.
17
G0011321
G0011221
G0011121
3 Separator Basics
3.2
3.2.1
The MOPX 205 TGT-24 is a high-speed centrifugal separator intended for marine and land applications. It is specifically designed for cleaning of mineral oils from water and solid particles (sludge). The cleaned oil is discharged continuously, while the sludge is discharged at intervals. The separator can be operated either as a purifier or as a clarifier. When operated as a purifier the separator discharges the separated water continuously. When the oil contains only small amounts of water the separator is operated as a clarifier, discharging the water together with the solid particles. The separator has to be installed together with devices for control of its operation. It can be delivered with a built-on pump for oil inlet feed.
G0685111
DANGER
The MOPX 205 TGT-24 separator
Disintegration hazards Use the separator only for the purpose and parameters (type of liquid, rotational speed, temperature, density etc.) specified in chapter 8 Technical Reference on page 169 and in the Purchase Order documents. Consult your Alfa Laval representative before any changes outside these parameters are made.
18
3 Separator Basics
3.2.2
Overview
The separator comprises a processing part and a driving part. It is driven by an electric motor (10). Mechanically, the separator machine frame is composed of a bottom part, a top part and a frame hood. The motor is flanged to the frame as shown in the illustration. The frame feet (5) are vibration damping. The bottom part of the separator contains the horizontal driving device (6), driving shaft with couplings (8, 9), a worm gear (7) and a vertical spindle (3). The bottom part also contains an oil bath for the worm gear, a brake and a revolution counter. The frame top part and the frame hood contain the processing parts of the separator, the inlet, outlets and piping (1). The liquid is cleaned in the separator bowl (2). This is fitted on the upper part of the vertical spindle and rotates at high speed in the space formed by the frame top part and frame hood. The bowl is of disc type and also contains the hydraulically operated discharge mechanism which empties the bowl of sludge. The main inlets and outlets are shown with connection numbers in the illustration. These numbers correspond with the numbers used in the connection list and the basic size drawing which can be found in chapter 8 Technical Reference on page 169, where also permissible pressures and operating conditions are specified. As option the separator can be equipped with a feed inlet pump (4).
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 201. 206. 220. 221. 222. 372. 376. Inlet and outlet device Bowl Vertical driving device with bowl spindle Feed inlet pump (option) Frame feet Horizontal driving device Worm gear Friction coupling Elastic coupling Electric motor Unseparated oil inlet Sealing/displacement water inlet Clean oil outlet Water outlet Sludge discharge outlet Bowl opening water inlet Bowl closing and make-up water inlet
19
G0580361
3 Separator Basics
3.2.3
The main parts of the power transmission between motor and bowl are shown in the illustration. The friction coupling ensures a gentle start and acceleration and at the same time prevents overloading of the worm gear and motor. The worm gear has a ratio which increases the bowl speed several times compared to the motor speed. For correct ratio see chapter 8.1 Technical data on page 170. To reduce bearing wear and the transmission of bowl vibrations to frame and foundation, the top bearing of the bowl spindle is mounted in a spring casing. The worm wheel runs in a lubricating oil bath. The bearings on the spindle and the worm wheel shaft are lubricated by the oil splash produced by the rotating worm wheel.
1. 2. 3. 4. 5. 6.
Bowl spindle Top bearing and spring casing Worm wheel Worm Friction coupling Worm wheel shaft
Brake The separator is equipped with a brake to be used when stopping the separator. The use of the brake reduces the retardation time of the bowl and critical speeds will therefore be quickly passed. The brake lining acts on the outside of the coupling pulley.
G0246321
1. 2.
20
G0246431
3 Separator Basics
3.2.4
Revolution counter (1) A revolution counter indicates the speed of the separator and is driven from the worm wheel shaft. The correct speed is needed to achieve the best separating results and for reasons of safety. The number of revolutions on the revolution counter for correct speed is shown in chapter 8 Technical Reference on page 169. Refer to name plate for speed particulars.
Sight glass (2) for oil sump The sight glass shows the oil level in the worm gear housing.
1. 2. 3. 4. 5.
Revolution counter Oil sight glass Sight glass Back pressure gauge Cover interlocking switch
Sight glass (3) for separated water outlet The sight glass shows the flow of the separated water and if any oil is escaping through the water outlet. If so, see7 Trouble-tracing on page 157.
21
G0644631
3 Separator Basics
Back pressure gauge (4) Correct limits for the back pressure in the clean oil outlet can be found in chapter 8.2 Connection list on page 172. Increasing back pressure in the clean oil outlet can be caused by: restriction in the outlet piping, e.g. a buckled or bent pipe, increased throughput, increased viscosity, decreased separating temperature.
Cover interlocking switch (5) The cover interlocking switch should be connected to the starter equipment so that starting of the motor is prevented when the separator hood is not (completely) closed.
3.2.5
The separator can be equipped with a built-on pump of gear type. The pump is driven by the horizontal driving shaft. This pump feeds the oil to the feed inlet (201).
Gear pump
22
G0588811
3 Separator Basics
3.2.6
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 201. 206. 220. 221. 372. 376.
Water paring chamber Gravity disc or clarifier disc Small lock ring (with paring chamber cover) Oil paring chamber Level ring Distributor Top disc Bowl hood Bowl disc stack Large lock ring Sludge port * Sludge space Bowl body Sliding bowl bottom* Operating slide * Nozzle * Spring * Water paring disc Oil paring disc Inlet pipe Distributing cone Bowl hood seal ring * Drain valve plug * Opening chamber * Control paring disc * Spring support * Unseparated oil inlet Displacement/conditioning water inlet Clean oil outlet Water outlet Opening water inlet * Closing and make-up water inlet * Sectional view of separator bowl, feed and discharge assembly and operating mechanism
23
G0685211
3 Separator Basics
Inlet and outlet device The inlet and outlet device consists of the following parts: The inlet (201). This comprises the feed connection and the long inlet pipe (20) which extends into the middle of the bowl. The outlets (220, 221). These comprise the discharge cover and the paring discs (18, 19) which pump the separated oil and water out of the bowl. Each paring disc is located in a paring chamber (1, 4) in the top of the bowl.
The inlet and outlet device is held together by the inlet pipe threading which is fixed to the oil paring disc. O-rings and a seal ring seal the connections between the parts. The outlet connection housing is fastened to the separator frame hood. Height adjusting rings determine the height position of the paring discs in the paring chambers.
Separator bowl The separator bowl with its sludge discharge mechanism is built-up as follows: The bowl body (13) and bowl hood (8) are held together by the large lock ring (10). Inside the bowl are the distributing cone (21), the distributor (6) and the disc stack (9). The disc stack is kept compressed by the hood. The sliding bowl bottom (14) forms an internal separate bottom in the bowl. The bowl top is covered by the paring chamber cover (4). The space between this cover and the top disc (7) is the upper paring chamber with the upper paring disc which pumps the separated water out of the bowl. The oil paring chamber with its paring disc is located inside the upper part of the top disc. From this space the cleaned oil is pumped out of the bowl. The sludge space (12) is the space between the sliding bowl bottom and the bowl hood in the bowl periphery. It is kept closed by the sliding bowl bottom which seals against a seal ring (22) in the bowl hood.
24
3 Separator Basics
Sludge discharge mechanism At intervals decided by the operator, the sliding bowl bottom drops to empty the bowl of sludge. The sludge discharge mechanism, which controls the sliding bowl bottom, comprises an operating slide (15) and an operating paring disc device. Passive parts are: nozzles (16) and drain valve plugs (23). The operating water device on the underside of the bowl supplies opening (372) and closing/make-up (376) water to the discharge mechanism via the control paring disc (25).
25
3 Separator Basics
3.3
3.3.1
Separating function
Purifier bowl
Characteristic parts The illustration shows characteristic parts of the purifier bowl: 1. The gravity disc, which should be chosen according to directions in chapter 4.1.2 Selection of gravity disc on page 36. The gravity disc determines the interface position (see below) in a purifier bowl. 2 The level ring diameter determines the free oil level in the bowl (the interface between oil and air in the centre of the bowl).
A purifier bowl has two liquid outlets, 220 (oil) and 221 (water).
Position of interface An interface (1) must be formed between the oil and water in the bowl. In order to achieve optimum separation of the oil, the interface must be maintained in the correct position, which is between the disc stack and the outer edge of the top disc. If the interface moves outside the outer edge of the top disc the water seal will break and oil will be discharged with the water. An interface positioned inside the disc stack will cause bad separation results. The position of the interface is adjusted by altering the pressure balance of the liquid phases, oil and water, inside the separator. This is done by exchanging the gravity disc. For this purpose a number of gravity discs with various hole diameters is delivered with the separator.
Purifier bowl
26
G0047031
G0685521
3 Separator Basics
A.
B.
C.
Factors influencing the interface position: 1. Oil viscosity, density and throughput Oil with high density and/or high viscosity, as well as high throughput, will position the oil/water interface closer to the bowl periphery than for oil with low properties.
G0011821
A. B.
27
G0011721
3 Separator Basics
2. Gravity disc To compensate for the above factors the interface is adjusted to a correct position by altering the outlet for the water, i.e. exchanging the gravity disc. Changing to a gravity disc with a larger hole diameter will move the interface towards the bowl periphery whereas a disc with a smaller hole diameter will move the interface closer to the bowl centre.
G0011921
A. B.
Gravity disc with large hole diameter Gravity disc with small hole diameter
3. Excessive back pressure Excessively high back pressure in the oil outlet prevents the oil from being pumped out. The inner oil level will then move towards centre of the bowl and, at the same time, push the oil/water interface outwards towards the bowl periphery. The effect is a wrong interface position, which may cause broken water seal.
A. B. Excessive back pressure Normal back pressure
3.3.2
Clarifier bowl
Characteristic parts The illustration shows characteristic parts of the clarifier bowl: 1. In clarification, the gravity disc is replaced by a so called clarifier disc, i.e. a disc with smallest possible hole diameter () which seals off the water outlet. No liquid seal is needed when clarifying. The level ring which has a large hole diameter ().
2.
The clarifier bowl has only one liquid outlet, 220 (oil).
Clarifier bowl
28
G0685531
G0012021
3 Separator Basics
3.3.3
Normal separation
Unseparated oil is fed into the bowl through the inlet pipe (11) and is led via the distributor (4) and distributing cone (12) towards the periphery of the bowl. When the oil reaches slots of the distributor, it will rise through the channels formed by the disc stack (6) where it is evenly distributed into the disc stack. The oil is continuously separated from water and particles as it will flow towards the centre of the bowl. When the cleaned oil leaves the disc stack it rises upwards, flows over the level ring (3) and enters the oil paring chamber (2). From here it is pumped by the non-rotating oil paring disc (10) and leaves the bowl through outlet (220). Separated water, sludge and solid particles, which are heavier than the oil, move towards the periphery of the bowl and collect in the sludge space (7). The bowl content is discharged at preselected intervals through the sludge ports (8). At purification the separated water rises along the outside of the top disc (5) over gravity disc (1) and is then pumped out by the non-rotating upper paring disc (9). The water then leaves the bowl through water outlet (221).
G0693011
Separating principle 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 201. 206. 220. 221. Gravity/clarifier disc Oil paring chamber Level ring Distributor Top disc Bowl disc stack Sludge space Sludge port Upper paring disc (water) Oil paring disc Inlet pipe Distributing cone Bowl hood Unseparated oil inlet Sealing/displacement water inlet Clean oil outlet Water outlet (only at purification)
29
3 Separator Basics
3.3.4
Sludge discharge interval The MOPX-separator is a total-discharge type separator which completely discharges sludge and water from the bowl. The appropriate time to be choosen between sludge discharges depends on local conditions because many factors influence accumulation and hardening of sludge between discharges. However, keep the discharge interval within the minimum and maximum time stated in 8.1 Technical data on page 170. Long intervals between sludge discharges can cause accumulation and compaction of sludge. The sludge may then break-up unevenly on discharge and cause the bowl to become unbalanced. If such unbalance is too large, there is risk of serious separator damage and injury to personnel.
30
3 Separator Basics
Closed bowl (normal operation) The sliding bowl bottom (2) is pressed upwards by force of the closing water in the closing water space (6) under the sliding bowl bottom which is greater than the force of the process liquid above the sliding bowl bottom. The operating slide (3) is pressed upwards by the springs (9); the valve plugs (8) cover the drain channels (7).
Bowl opens for discharge Before starting the sludge discharge cycle the oil feed should be cut off. At purification, displacement water (206) should be added to the bowl before the discharge to avoid oil losses. The oil/water interface (h1) moves towards the centre of the bowl (h2). The opening water (372), which is supplied into the space above the operating slide (3), overcomes the force from the springs (9) and the operating slide is pressed downwards. The drain channels (7) open and the closing water is drained. This allows the force on the underside of the sliding bowl bottom (2) to become lower than the force on the upper side. The sliding bowl bottom moves downwards and the bowl opens for a discharge through the sludge ports (1).
G0693031
Separator bowl, feed and discharge assembly, control paring disc and liquid flow 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Sludge port Sliding bowl bottom * Operating slide * Nozzle * Nozzle * Closing water space Drain channel Drain valve plug Spring * Opening chamber *
Bowl closes after discharge The opening water supply is closed and the water in the opening chamber is drained through nozzle (5). The springs (9) move the operating slide upwards and the drain channels (7) are closed by the drain valve plugs (8). The closing water (376) is supplied via the nozzle (4) to the closing water space which presses the sliding bowl bottom (2) upwards. The bowl closes and the sludge discharge cycle is complete. At purification, sealing water (206) must be supplied to the bowl before the oil supply is turned-on. Bowl closing water should be supplied during the sludge discharge sequence and at intervals during the separation sequence to replace evaporated water.
206. Sealing/displacement water inlet 372. Opening water inlet * 376. Closing and make-up water inlet * * Parts effecting a sludge discharge
31
3 Separator Basics
3.4 Definitions
3.4
Definitions
Pressure in the separator outlet. Liquid/solids separation with the intention of separating particles, normally solids, from a liquid (oil) having a lower density than the particles. An optional disc, which replaces the gravity disc in the separator bowl, in the case of clarifier operation. The disc seals off the heavy phase (water) outlet in the bowl, thus no liquid seal exists. See Back pressure. Mass per volume unit. Expressed in kg/m3 at a specified temperature, normally at 15 C. Disc in the bowl hood for positioning the interface between the disc stack and the outer edge of the top disc. This disc is only used in purifier mode. Boundary layer between the heavy phase (water) and the light phase (oil) in a separator bowl.
Intermediate Service Overhaul of separator bowland inlet/outlet. Renewal of seals in bowl inlet/ (IS) outlet and operating water device. Major Service (MS) Overhaul of the complete separator, including bottom part (and activities included in an Intermediate Service, if any). Renewal of seals and bearings in bottom part. Light phase: the lighter liquid separated, e.g. oil. Heavy phase: the heavier liquid separated, e.g. water. Liquid/liquid/solids separation with the intention of separating two intermixed and mutually insoluble liquid phases of different densities. Solids having a higher density than the liquids can be removed at the same time. The lighter liquid phase (oil), which is the major part of the mixture, shall be purified as far as possible. Solids separated from a liquid. Ejection of sludge from the separator bowl. The feed of process liquid to the separator per time unit. Expressed in m3/hour or litres/hour. Fluid resistance against movement. Normally expressed in centistoke (cSt = mm2/s), at a specified temperature. Water in the solids space of the separator bowl which prevents the light phase (oil) from leaving the bowl through the heavy phase (water) outlet, in purifier mode.
Phase Purification
32
4 Operating Instructions
Contents
4.1 Operating routine
4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 Before first start Selection of gravity disc Ready for start Start and running-up Running Normal stop Safety stop 36 36 36 38 39 41 41 42
35
4 Operating Instructions
4.1
Operating routine
These operating instructions are related only to the separator itself. If the separator is part of a system or module, also follow the instructions for the system.
4.1.1
Technical demands for connections and logical limitations for the separator are listed in chapter 8 Technical Reference on page 169: Technical data Connection list Interface description Basic size drawing Foundation drawing.
Before first start the following shall be checked: 1. Ensure the machine is installed correctly and that feed lines and drains have been flushed clean. Fill oil in the gear housing. (The separator is delivered without oil in the gear housing). Fill up to slightly above the middle of the sight glass. For grade and quality of oil see 8.5.2 Recommended lubricating oils on page 182. Make sure the direction of rotation of the motor corresponds to the arrow on the motor, see 8.6.9 Machine plates and safety labels on page 200.
G0262011
2.
3.
4.1.2
The separator is delivered with a set of gravity discs with different diameters. The hole diameter of the gravity disc sets the position of the oil/water interface in the separator, see page 27. The separation efficiency can be optimized by selection of the correct diameter for each oil quality. How to replace a gravity disc is described in 6.3 Bowl hood and disc stack (IS) on page 105.
36
4 Operating Instructions
Clarification When the separator is run as a clarifier, select the gravity disc with the smallest hole diameter. See the Spare Parts Catalogue for actual diameters delivered.
Purification The best separation results are obtained by using a gravity disc with as large a hole diameter as possible, which will not cause a broken water seal in the bowl or an emulsification in the water outlet. The heavier or more visous the oil is and the greater the feed rate the smaller the diameter should be. As a guide the 8.6.6 Gravity disc nomogram on page 194, can be used when the density of the oil at a temperature of +15 C is known. The hole diameter of the first gravity disc to try can be read directly from the nomogram. The nomogram is based on the properties of fresh water in the oil and is purely theoretical. In practical operation operation, practice the following general rule: 1. Fit a gravity disc one size larger than recommended in the nomogram for the actual conditions. 2. Run the separator 3. Observe if oil flows through the water outlet (seen through the sight glass). If yes, stop the separator and fit the next smaller gravity disc. If no, stop the separator and fit the next larger gravity disc.
4. Repeat steps 1-3 above until the gravity disc with the largest hole diameter has been selected without causing a break of the water seal.
37
4 Operating Instructions
4.1.3
To achieve the best separation results the bowl should be in a clean condition. 1. 2. Check that the hinged bolts for the frame hood are fully tightened. Check that all inlet and outlet connections have been correctly made and properly tightened.
CAUTION
Burn hazards Make sure that hose connections and flange couplings are properly assembled and tightened. Escaping hot liquid can cause burns.
Check for leakages (not admitted)
3.
Check that the oil level is slightly above the middle of the sight glass.
NOTE
G0262011
During operation the oil level should be barely visible in the lower part of the sight glass. Too much or too little oil can damage the separator bearings.
Check the oil level
Fill if necessary. See chapter 8.5 Lubricants on page 180, for a list of recommended oils. 4. Make sure that the brake is released.
DANGER
Disintegration hazards After change of feed the sludge discharge interval must be adjusted. Too long intervals between discharges can result in breakdown.
Release the brake
38
G0639711
S0009821
4 Operating Instructions
4.1.4
1. Start the separator. 2. Check the direction of rotation of the bowl. The revolution counter should turn clockwise.
DANGER
G0246211
Disintegration hazards When power cables have been connected, always check direction of rotation. If incorrect, vital rotating parts could unscrew.
3. Be alert for unusual noises and conditions. 4. Note the normal occurrence of critical speed periods. Some vibrations occur for short periods during the starting cycle, when the separator passes through its critical speeds. This is normal and passes over without danger. Try to learn the vibration characteristics of the critical speed pattern.
DANGER
Disintegration hazards When excessive vibration occurs, keep bowl filled and stop separator. The cause of the vibration must be identified and rectified before the separator is restarted. Excessive vibration may be due to incorrect assembly or insufficient cleaning of the bowl. In the trouble-tracing chapter 7.1.1 Separator vibrates on page 158, a number of causes are described that can create vibration.
39
4 Operating Instructions
5.
Check, if possible, the current consumption of the motor starter to ensure that the separator has reached full speed. At full speed the starter ammeter reading has decreased from a high starting value to a low, steady value - the idling value, which is slightly lower than the normal operating value. The time to reach full speed should not exceed the limit given in chapter 8 Technical Reference on page 169.
Current increases when the coupling engages...
6. 7.
When the separator runs normally, open the water supply valve(s). For purification: a. Supply water to form the water-seal. The water should have the same temperature as the process liquid and be supplied quickly. b. Close the water feed when water flows out through the water outlet. c. Start the oil feed slowly to avoid breaking the water seal. Then fill the bowl as quickly as possible.
S0009631
... to decrease to a stable value when full speed has been reached
8.
For clarification: a. Start the oil feed with full flow. Fill the bowl as quickly as possible.
9.
For both purification and clarification modes: Check the separator inlet and outlet pressures. See recommended values in your system documentation.
10. Adjust to desired throughput. 11. Discharge by opening the valve for opening water valve ( at connection 372) until a discharge is heard. For maximum and minimum time for discharge intervals, see chapter 8 Technical Reference on page 169.
40
S0009621
4 Operating Instructions
4.1.5
Running
1. Check that the feed has the correct flow and temperature. See chapter 8 Technical Reference on page 169 for correct values. .
DANGER
Disintegration hazards Ensure that correct discharge intervals and cleaning procedures are used. Unbalance due to improper washing out of solids may lead to contact between rotating and non-rotating parts.
2. For daily condition checks, see 5.2.1 Daily checks on page 49.
4.1.6
Normal stop
1. Shut off the feed. 2. Carry out a sludge discharge before stopping the separator. Otherwise the bowl must be cleaned manually before the next start up. 3. After the discharge, supply displacement/ sealing water to fill the bowl. Stop the separator, the bowl filled with liquid. 4. Apply the brake.
G0639811
5. Wait until the separator has come to a complete standstill (3,5 - 4,5 minutes).
DANGER
Entrapment hazards Make sure that rotating parts have come to a complete standstill before starting any dismantling work.
S0051111
41
4 Operating Instructions
4.1.7
Safety stop
If the separator begins to vibrate excessively during operation, stop it immediately by pushing the safety stop. The separator motor is switched off. Keep the bowl filled during the run-down to minimize the excessive vibration.
Hazard!
Evacuate the room. The separator may be hazardous when passing its critical speeds during the run-down.
DANGER
Disintegration hazards
Push the safety stop
S0009911
CAUTION
Disintegration hazards After a safety stop the cause of the fault must be identified. If all parts have been checked and the cause remains unclear, contact Alfa Laval for advice.
42
S0055611
5 Service Instructions
Contents
5.1 Periodic maintenance
5.1.1 5.1.2 5.1.3 5.1.4 Introduction Maintenance intervals Maintenance procedure Service kits 45 45 45 47 48 49 49 49 50 52 55 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9
5.4.10 Erosion 5.4.11 Elastic plate in coupling 5.4.12 Guide surfaces 5.4.13 Inlet pipe and oil paring disc 5.4.14 Level ring 5.4.15 Lock ring; priming 5.4.16 Lock ring; wear and damage 5.4.17 Oil paring disc; height position 5.4.18 Operating mechanism 5.4.19 Control paring disc device; height position 5.4.20 Operating slide 5.4.21 Sliding bowl bottom 5.4.22 Springs for operating mechanism 5.4.23 Worm wheel and worm; wear of teeth 5.4.24 Worm wheel shaft; radial wobble 5.4.25 Cover interlocking switch
56 56 57 57 60 61 62 64 66 66 67 69 69 70 71 71 71
5.3.10 Lock ring; wear and damage 5.3.11 Operating mechanism 5.3.12 Operating slide 5.3.13 Sliding bowl bottom 5.3.14 Springs for operating mechanism 5.3.15 Worm wheel and worm; wear of teeth 5.3.16 Cover interlocking switch
43
5 Service Instructions
5.6 Cleaning
5.6.1 5.6.2 5.6.3 External cleaning Cleaning agents Cleaning of bowl discs
86 86 86 88 89 89
92 93 93 94 94 97
5.8 Vibration
5.8.1 Vibration analysis
44
5 Service Instructions
5.1
5.1.1
Periodic maintenance
Introduction
Periodic (preventive) maintenance reduces the risk of unexpected stoppages and breakdowns. Follow the maintenance logs on the following pages in order to facilitate the periodic maintenance.
DANGER
Disintegration hazards Separator parts that are either worn beyond their safe limits or incorrectly assembled may cause severe damage or fatal injury.
5.1.2
Maintenance intervals
The following directions for periodic maintenance give a brief description of which parts to be cleaned, checked and renewed at different maintenance intervals. The maintenance logs for each maintenance interval later in this chapter give detailed enumeration of the check points that must be done. Daily checks consist of minor check points to carry out for detecting abnormal operating conditions.
Oil change The oil change interval is every 1000-1500 hours or at least once every year if the total number of operating hours is less than 1000-1500 hours. When using a group D oil, time of operation between oil changes can be extended from the normal 1000-1500 hours to 2000 hours.
45
5 Service Instructions
Intermediate Service (IS) Intermediate Service consists of an overhaul of the separator bowl, inlet/outlet and operating device every 3 months or 2000 operating hours. Seals in bowl and gaskets in inlet/outlet device are renewed.
Major Service (MS) Major Service consists of an overhaul of the complete separator and includes an Intermediate Service every 12 months or 8000 operating hours. Seals and bearings in the bottom part are renewed.
3-year Service (3S) 3-year Service consists of renewing the frame feet. The vibration damping rubber cushions get harder with increased use and age.
Installation
1st year
2nd year
3rd year
46
5 Service Instructions
5.1.3
Maintenance procedure
At each Intermediate and Major Service, take a copy of the maintenance log and use it for notations during the service. An Intermediate and Major Service should be carried out in the following manner: 1. Dismantle the parts as mentioned in the maintenance log and described in chapter 6 Dismantling/Assembly on page 99. Place the separator parts on clean, soft surfaces such as pallets. 2. Inspect and clean the dismantled separator parts according to the maintenance log. 3. Fit all the parts delivered in the service kits while assembling the separator as described in chapter 6 Dismantling/Assembly on page 99. The assembly instructions have references to check points which should be carried out before and during the assembly.
47
5 Service Instructions
5.1.4
Service kits
Special service kits are available for Intermediate Service (IS) of top part and Intermediate Service (IS) of bowl as well as for Major Service (MS). For other services the spare parts have to be ordered separately. Note that the parts for IS are not included in the MS kit. For separators with built-on pump there i also a service kit for the pump. The contents of the service kits are described in the Spare Parts Catalogue.
Kits are available for Intermediate Service of top part and of bowl and for Major Service
S0021041
NOTE
Always use Alfa Laval genuine parts as otherwise the warranty will become invalid. Alfa Laval takes no responsibility for the safe operation of the equipment if non-genuine spare parts are used.
DANGER
Disintegration hazards Use of imitation spare parts may cause severe damage.
48
5 Service Instructions
5.2
5.2.1
Maintenance Logs
Daily checks
The following steps should be carried out daily. Main component and activity Inlet and outlet Check for leakage Separator bowl Check for vibration and noise Horizontal driving device Worm wheel shaft and gear casing Check for vibration and noise Check Electrical motor Check for heat, vibration and noise
1) See manufacturers instruction
1)
Part
Page
Notes
Connecting housing
93
5.2.2
Oil change
The oil change and check of worm gear should be carried out every 1000-1500a) hours of operation. Note! In a new installation, or after replacement of gear, change the oil after 200 operating hours. Main component and activity Horizontal driving device Worm wheel shaft and gear housing Check Renew Worm wheel and worm Oilb) in gear housing 89 92 Part Page Notes
When the separator is running for short periods, the lubricating oil must be changed every 12 months even if the total number of operating hours is less than 1000-1500 hours (2000 h).
a)
When using a group D oil, time of operation between oil changes can be extended from the normal 10001500 hours to 2000 hours. See chapter 8.5 Lubricants on page 180 for further information.
b)
49
5 Service Instructions
5.2.3
Name of plant: Separator: Total running hours: Date: Main component and activity Inlet and outlet Clean and inspect
66 70
Upper paring disc Lock ring Bowl hood Top disc Oil paring disc Level ring Bowl discs Distributor Distributing cone Sliding bowl bottom Bowl body Bowl spindle cone and bowl body nave Operating mechanism
67 56 66 66 88 70 57 69, 71 57 60 62 65 61
Check
50
5 Service Instructions
Main component and activity Horizontal driving device Worm wheel shaft and gear housing Check Renew Electrical motor Lubrication (if nipples are fitted) Signs and labels on separator Check attachment and legibility
Part
Page
Notes
89 92
Note! Renew all parts included in the Intermediate Service kit (IS).
51
5 Service Instructions
5.2.4
Name of plant: Separator: Total running hours: Date: Main component and activity Inlet and outlet Clean and inspect
66 70
Upper paring disc Lock ring Bowl hood Top disc Oil paring disc Level ring Bowl discs Distributor Distributing cone Sliding bowl bottom Bowl body Bowl spindle cone and bowl body nave Operating mechanism
80, 67 56 66 66 88 70 57 69, 71 57 60 65 65 61 82
Check
Corrosion Cracks Erosion Galling of guide surface Disc stack pressure Height position of oil paring disc
52
5 Service Instructions
Main component and activity Paring disc device Clean and check Check Vertical driving device Clean and check
Part
Page
Notes
82
Bowl spindle Buffer springs and ball bearing housing Radial wobble of bowl spindle
74 72 126
Renew Horizontal driving device Worm wheel shaft and gear housing Check
Spindle bearings
Worm wheel and worm Radial wobble of worm wheel shaft Axial play of elastic plate
89 84 77 138 92
Renew
Brake Clean and check Renew Friction coupling Clean and check Renew Electrical motor Lubrication (if nipples are fitted) Signs and labels on separator Check attachment and legibility Safety label on hood Direction of rotation arrow Power supply frequency Monitoring equipment (option) Function check Cover interlocking switch 71 200 200 200 See sign on motor Worm wheel coupling Friction pads 75 Spring and brake shoe Friction pad 73 73
53
5 Service Instructions
Main component and activity Oil feed pump (if applicable) Cleaning and inspection
Part
Page
Notes
Bushings, wear gaskets, flexible coupling, relief/safety valve and impeller shaft Lipseal rings
148
Renew
54
5 Service Instructions
5.2.5
Renew the frame feet as described below. The 3year service should be carried out in conjunction with a Major Service (MS).
Frame feet, renewal 1. Disconnect pipes, hoses and cables connected to the separator. 2. Remove the nuts (3, 4). 3. Lift the separator.
NOTE
When lifting a separator it must always hang securely. See separate instruction in chapter 5.5 Lifting instructions on page 85. 4. Renew the vibration dampers (1, 2). 5. Lower the frame. Check that the bolts do not press against the edges of the holes. 6. Tighten the nut (3) to 20 Nm. 7. Hold the nut (3) firmly and secure with the lock nut (4). 8. Connect the previously disconnected pipes, hoses and cables.
1. 2. 3. 4. Vibration damper, upper Vibration damper, lower Nut Lock nut
G0258911
55
5 Service Instructions
5.3
5.3.1
Poor sealing between the bowl hood seal ring and the sealing edge of the sliding bowl bottom will cause a leakage of process liquid from the bowl. Renew the bowl hood seal ring at each Intermediate Service (IS).
Knock out the old ring by means of a pin inserted in the holes intended for this purpose.
Fit the new ring as follows: Press the ring into the groove with a straight wooden board placed across the ring
.
NOTE
If the new ring is too narrow, place it in hot water (70-80 C) for about 5 minutes. If it is too wide, it will shrink after drying in 80-90 C for about 24 hours.
G0206411
56
G0206311
G0206211
5 Service Instructions
5.3.2
Impact marks on the spindle cone or in the bowl body nave may cause poor fit and out-of-balance vibrations. The bowl spindle and the nave should also be checked if the bowl spindle has been dismantled or if the bowl runs roughly. Corrosion may cause the bowl to stick firmly to the spindle cone and cause difficulties during the next dismantling. Remove any impact marks with a scraper and/or whetstone.
Rust can be removed by using a fine-grain emery cloth (e.g. No 320). Finish with polishing paper (e.g. No 600).
NOTE
Always use a scraper with great care. The cone shape must not be deformed.
Remove impact marks from the nave and cone
5.3.3
Corrosion
Evidence of corrosion attacks should be looked for and rectified each time the separator is dismantled. Main bowl parts such as the bowl body, bowl hood and lock ring must be inspected with particular care for corrosion damage.
DANGER
G0206111
Disintegration hazard Inspect regularly for corrosion damage. Inspect frequently if the process liquid is corrosive.
Main bowl parts to check for corrosion
57
G0526711
5 Service Instructions
Always contact your Alfa Laval representative if you suspect that the largest depth of the corrosion damage exceeds 1,0 mm or if cracks have been found. Do not continue to use the separator until it has been inspected and given clearance for operation by Alfa Laval. Cracks or damage forming a line should be considered as being particularly hazardous.
Non-stainless steel and cast iron parts Corrosion (rusting) can occur on unprotected surfaces of non-stainless steel and cast iron. Frame parts can corrode when exposed to an aggressive environment.
Stainless steel Stainless steel parts corrode when in contact with either chlorides or acidic solutions. Acidic solutions causes a general corrosion. The chloride corrosion is characterised by local damage such as pitting, grooves or cracks. The risk of chloride corrosion is higher if the surface is: Exposed to a stationary solution. In a crevice. Covered by deposits. Exposed to a solution that has a low pH value.
Example of chloride corrosion in stainless steel
A corrosion damage caused by chlorides on stainless steel begins as small dark spots that can be difficult to detect.
58
S0020611
5 Service Instructions
1. Inspect closely for all types of damage by corrosion and record these observations carefully. 2. Polish dark-coloured spots and other corrosion marks with a fine grain emery cloth. This may prevent further damage.
Polish corrosion marks to prevent further damage
DANGER
Disintegration hazard Pits and spots forming a line may indicate cracks beneath the surface. All forms of cracks are a potential danger and are totally unacceptable. Replace the part if corrosion can be suspected of affecting its strength or function.
Other metal parts Separator parts made of materials other than steel, such as brass or other copper alloys, can also be damaged by corrosion when exposed to an aggressive environment. Possible corrosion damage can be in the form of pits and/or cracks.
59
S0020511
5 Service Instructions
5.3.4
Cracks
Cracks can initiate on the machine after a period of operation and propagate with time. Cracks often initiate in an area exposed to high cyclic material stresses. These are called fatigue cracks. Cracks can also initiate due to corrosion in an aggressive environment. Although very unlikely, cracks may also occur due to the low temperature embrittlement of certain materials.
The combination of an aggressive environment and cyclic stresses will speed-up the formation of cracks. Keeping the machine and its parts clean and free from deposits will help to prevent corrosion attacks.
DANGER
Disintegration hazard All forms of cracks are potentially dangerous as they reduce the strength and functional ability of components. Always replace a part if cracks are present.
It is particularly important to inspect for cracks in rotating parts and especially the pillars between the sludge ports in the bowl wall. Always contact your Alfa Laval representative if you suspect that the largest depth of the damage exceeds 1,0 mm. Do not continue to use the separator until it has been inspected and cleared for operation by Alfa Laval.
60
5 Service Instructions
5.3.5 NOTE
Ensure that the disc stack pressure is sufficient to maintain bowl balance. Insufficient pressure in the disc stack can cause vibration and reduce lifetime of ball bearings.
The lock ring (1) should press the bowl hood (2) firmly against the bowl body (3). The hood in turn should exert a pressure on the disc stack (4), clamping it in place.
Compress the disc stack by tightening the lock ring, see chapter 6.3.3 Assembly on page 109. Correct pressure is obtained when it is possible to tighten the lock ring so far by hand that the -mark on the lock ring is positioned 60 - 90 before the mark on the bowl body. To achieve this, add an appropriate number of discs to the top of the disc stack beneath the top disc. Then advance the lock ring by giving the spanner handle some blows till the -marks are passed and the bowl is fully assembled. If the -marks do not reach or pass each other, the reason could be an incorrectly assembled bowl or to many discs in the disc stack. Reassemble and check.
G0135811
61
G0544431
5 Service Instructions
5.3.6
Erosion
Erosion can occur when particles suspended in the process liquid slide along or strike against a surface. Erosion can become intensified locally by flows of higher velocity.
G0205221
DANGER
Disintegration hazard Inspect regularly for erosion damage. Inspect frequently if the process liquid is erosive.
Always contact your Alfa Laval representative if the largest depth of any erosion damage exceeds 1,0 mm. Valuable information as to the nature of the damage can be recorded using photographs, plaster impressions or hammered-in lead. Erosion is characterised by: Burnished traces in the material. Dents and pits having a granular and shiny surface.
Surfaces particularly subjected to erosion are: 1. 2. 3. 4. 5. 6. 7. The upper paring disc. The top disc. The pillars between the sludge ports in the bowl wall. The sealing edge of the bowl body for the seal ring in the sliding bowl bottom. The underside of the distributor in the vicinity of the distribution holes and wings. The surface of the sliding bowl bottom that faces the conical part of the distributor. The sealing edge of the sliding bowl bottom.
G0581321
Look carefully for any signs of erosion damage. Erosion damage can deepen rapidly and consequently weaken parts by reducing the thickness of the metal.
62
5 Service Instructions
DANGER
Disintegration hazard Erosion damage can weaken parts by reducing the thickness of the metal. Pay special attention to the pillars between the sludge ports in the bowl wall. Replace the part if erosion can be suspected of affecting its strength or function.
63
5 Service Instructions
5.3.7
Guide surfaces
Check surfaces indicated (1) for burrs or galling. Rectify when necessary. Repair of galling on guide surfaces; see following pages. Before fitting the sliding bowl bottom, clean (do not degrease) the contact surfaces (1 and 2). Apply Alfa Laval lubricating paste or Molykote 1000 Paste with a well-cleaned brush on surfaces (1 and 2).
NOTE
To avoid the risk of galling, the contact surfaces (1) should be primed with a slide lacquer at every Major Service (MS). The slide-lacquered surfaces will be destroyed if the surfaces are degreased.
G0443331
Bowl body
Lubricate the O-ring and the seal ring with silicone grease making sure they are not damaged and lie properly in their grooves.
G0443341
Operating slide
1, 2 =
64
G0640311
G0443321
5 Service Instructions
Repair of galling on guide surfaces Galling (friction marks) may appear on guide surfaces in the operating system, the bowl body and the sliding bowl bottom. Surfaces subject to repair are indicated by an arrow.
G0205511
The example below describes the repair of the lower guide surface of the bowl body nave.
Guide surface in the bowl body
Recommended tools for correction of galling: Emery cloth, 240 grade. Hand drilling machine Degreasing agent. Fibre brush, 25mm. Fibre brush, 50 mm. Very fine single-cut file.
1. Clean the surface thoroughly with a degreasing agent, i.e. white spirit. This is important.
2. If the galling is excessive, first use the fine single-cut file. The file should be used with caution so that the damage is not made worse. Remove the high spots on the surface. Do not use rotating files or similar. Remove the high spots only - not the undamaged material.
G0205711
65
G0205611
5 Service Instructions
3.
An emery cloth of 240 grade should be used to smooth the edges and to remove any burnt-in foreign matter.
4.
Finish off by polishing the damaged spot with the fibre brushes and brush wax. It is recommended that the whole area where galling may occur is polished. Polishing will help smoothen the whole of the damaged area, even in the deepest parts.
Prime the repaired area with lubricating spray Molykote 321 R. Read the correct procedure under checkpoint 5.4.15 Lock ring; priming on page 80. Apply Alfa Laval lubricating paste or Molykote 1000 Paste to the surface after priming.
5.3.8
Damage to the threads and the top surface of level ring may cause the paring disc to scrape against the paring chamber cover even if the height has been adjusted correctly. Screw the inlet pipe into the paring disc and check that the inlet pipe turns easily.
G0581421
Check the threads of the inlet pipe and oil paring disc
5.3.9
Level ring
G0640411
Remove any burrs on the surface of the level ring with a file as the paring disc rests on that surface during the height position check.
Check the level ring for burrs
66
G0205911
G0205811
5 Service Instructions
DANGER
G0535211
Disintegration hazards Wear on large lock ring thread must not exceed safety limit. The -mark on lock ring must not pass opposite -mark by more than the specified distance.
1. 2. Lock ring O-ring for the bowl hood
In a new bowl the alignment marks on the lock ring and the bowl body are exactly opposite each other. If thread wear is observed, mark the bowl body at the new position of the alignment mark on the lock ring by punching a new alignment mark. If the original mark on the lock ring passes the mark on the bowl body by more than 25, an Alfa Laval representative must be contacted immediately. If the marks become illegible, an Alfa Laval representative should be contacted immediately to inspect thread wear and for determining the position of new alignment marks.
G0578131
The -mark on the lock ring must not pass the -mark on the bowl body by more than the distance A
67
5 Service Instructions
Damage The position of the threads, contact and guide surfaces are indicated by arrows in the illustration. Clean the threads, contact and guide surfaces with a suitable degreasing agent. Check for burrs and protrusions caused by impact. Watch your fingers for sharp edges. If damage is established, rectify using a whetstone or fine emery cloth (recommended grain size 240). If the damage is considerable, use a fine singlecut file, followed by a whetstone.
Clean and check thread, contact and guide surfaces of the lock ring
68
G0537241
5 Service Instructions
Reasons for dirt or deposits: Hard or unclean operating water. Change water supply or install a water softener or a fine filter. Sludge has been sucked down into bowl casing and into the operating system. Check the installation and the venting system of both the sludge tank and bowl casing drain.
69
5 Service Instructions
NOTE
Never reduce the height outside the sealing edge to reach the minimum profile height.
Min. height of the profile on sliding bowl bottom
If the seal ring for the sliding bowl bottom is to be replaced, turn the sliding bowl bottom upside down and inject compressed air through the hole on the underside. This will press the ring outwards far enough to be gripped easily.
70
G0207511
5 Service Instructions
WARNING
Risk for eye injury Wear safety goggles.
71
5 Service Instructions
5.4
5.4.1
5.4.2
Same as described in 5.3.2 Bowl spindle cone and bowl body nave on page 57.
5.4.3
The bowl spindle wobble should be checked if the bowl spindle has been dismantled or if rough bowl running (vibration) occurs.
NOTE
Spindle wobble will cause rough bowl run. This leads to vibration and reduces lifetime of ball bearings.
G0298421
Check the wobble before mounting the bowl. Before measuring, make sure that the buffer plugs are properly tightened. Fit a dial indicator in a support and fasten it to the frame. Remove the brake cover to get access to the coupling drum. Use the coupling drum to revolve the spindle manually. Measure the wobble at the top of the tapered end of the spindle. Permissible radial wobble is maximum 0,04 mm. If wobble is too large, renew all the ball bearings on the spindle.
Measure wobble after assembly. If it is still excessive, the spindle is probably damaged and must be replaced.
72
G0191521
5 Service Instructions
5.4.4
Brake
A worn or oily friction pad will lengthen the braking period. If the friction pad is worn: Remove the screws and exchange the friction pad.
NOTE
G0134111
If the friction pad is oily: Clean the friction pad and the coupling drum with a suitable degreasing agent. Roughen the friction surface of the friction pad with a coarse file.
NOTE
Identify the cause of oily friction pad. If oil is leaking from the gear housing, renew the sealing ring between the two parts.
G0134211
Checking of spring and brake shoe: Formation of rust on brake parts may cause the brake to jam. Remove any rust from the surface (1) of the brake shoe and the corresponding guide surface in the cap (2). Rub in Molykote Paste on the surfaces. Replace the spring (3) if it has become weak. This is indicated by noise when the brake is in released position. Oil the spring when assembling.
1. 2. 3. Contact surface on the brake shoe for the spring Guide surface in the cap for the brake shoe Spring
73
G0134311
5 Service Instructions
5.4.5
Weakened or broken buffer springs or defective contact surfaces for the buffers on the ball bearing housing may give rise to separator vibration (rough bowl run).
Top bearing springs In case of spring fracture, the complete set of springs should be replaced, even if only one spring is broken.
1. 2. 3. 4.
Ball bearing housing Examine the contact surface for the buffers on the ball bearing housing. In case of defects (indentations deeper than 0,5 mm), renew the housing as well as buffers and springs.
74
G0283621
G0527521
5 Service Instructions
5.4.6
Worn or oily pads in the coupling will cause a long acceleration period. If the separator does not attain full speed within about 3 minutes or the bowl loses speed during operation, the friction pads of the coupling may be worn or oily.
G0630211
Check the pads. If the pads are oily: Clean the pads and the inside of the coupling drum with a suitable degreasing agent. Roughen the friction surfaces of the pads with a coarse file.
Location of coupling friction blocks
If the pads are worn: Remove the screws and replace the pads.
NOTE
The screws are slotted in both ends. Replace all pads even if only one is worn.
1. 2. 3. Electric motor Elastic plate Friction block
G0641011
How to replace friction pads: Remove the electric motor (1) elastic plate (2) friction blocks (3). If disconnecting the motor cables, note the positions of cables in the terminal box to reconnect correctly (for correct direction of rotation). Remove the screws and replace the pads.
Three screws fix the friction pad to the coupling friction block (50 Hz); two screws in 60 Hz installations
75
G0630511
5 Service Instructions
Different friction blocks for different power supply frequencies When mounting new friction blocks, check that the blocks are correct for the power supply frequency. The measure A is different for 50 and 60 Hz separators. 50 Hz: 60 Hz: A = 55 mm A = 35 mm
Profile of friction block Measure A is different for 50 and 60 Hz installations
DANGER
Disintegration hazards When power cables have been connected, always check direction of rotation. If incorrect, vital rotating parts could unscrew causing disintegration of the machine.
5.4.7
Corrosion
5.4.8
Cracks
5.4.9
5.4.10 Erosion
Same as described in 5.3.6 Erosion on page 62.
76
G0603031
5 Service Instructions
Check the play as follows: Fit the elastic plate in its place in the coupling disc of the separator. Make sure that good contact is obtained.
Measure the distance from the frame ring (or motor adapter) to the elastic plate in the coupling disc.
77
G0528611
G0528511
G0528421
5 Service Instructions
Measure the distance from the motor coupling disc to the motor flange. X mm - Y mm = 2 mm. If required, adjust the position of the motor coupling disc.
78
G0528711
5 Service Instructions
Bowl body
79
5 Service Instructions
2 fibre brushes
Threads, guide and contact surfaces to be primed
1.
Clean the lock ring thoroughly with a degreasing agent and wipe it off.
2.
Spray the threads, guide and contact surfaces with slide lacquer Molykote 321 R. Let the lacquer air-cure for about 15 minutes.
80
G0207011
G0206911
5 Service Instructions
3. Use a fibre brush to polish the slide lacquer into the surface. The black spray will look like well-polished leather when properly done.
4. Spray the lock ring a second time and let it dry for about 15 minutes.
5. Polish the slide lacquer to a black shiny surface which can now last about a year. Proceed in the same way with the threads of the bowl body and with the guide surfaces of the bowl hood and bowl body.
81
G0207311
G0207211
G0207311
5 Service Instructions
When inlet and outlet parts have been mounted: Revolve the worm wheel shaft by hand. If it turns heavily or if a scraping noise is heard, wrong height adjustment or wrong fitting of the inlet pipe may be the cause.
82
5 Service Instructions
A: Distance to measure
83
G0684711
5 Service Instructions
84
G0246131
5 Service Instructions
5.5
Lifting instructions
When lifting the bowl out of the separator frame, the cap nut fixing the bowl to the bowl spindle and the screws fixing the bowl body to the operating water device must first be removed. Attach two endless slings or cables to the separator frame as illustrated. Length of each sling must be at least 1,5 metres.
NOTE
Machine weight without frame hood and bowl is approx. 500 kg.
Do not lift the separator unless the frame hood and bowl have been removed.
WARNING
Crush hazards Lift the separator in no other way than illustrated. A falling separator can cause accidents resulting in serious injuries and damage.
Lift the separator only after the frame hood and bowl have been removed. A=minimum 750 mm
When lifting the bowl, use the special lifting tool fastened on the bowl hood.
NOTE
Check that the lock ring is properly tightened. The height of the lock ring above the bowl body must not exceed 6 mm, see illustration. Weight to lift is approx. 70 kg.
G0641321
The lock ring must be properly tightened before the bowl is lifted. Distance A: maximum 6 mm
85
G0641221
5 Service Instructions
5.6 Cleaning
5.6
5.6.1
Cleaning
External cleaning
The external cleaning of the frame and motor should be restricted to brushing, sponging or wiping while the motor is running or is still hot. Never wash down a separator with a direct water stream. Totally enclosed motors can be damaged by direct hosing to the same extent as open motors and even more than those, because: Many operators believe that these motors are sealed, and normally they are not. A water jet played on these motors will produce an internal vacuum, which will suck the water between the metal-to-metal contact surfaces into the windings, and this water cannot escape. Water directed on a hot motor may cause condensation resulting in short-circuiting and internal corrosion.
Use a brush and sponge or cloth when cleaning
Be careful even when the motor is equipped with a protecting hood. Never play a water jet on the ventilation grill of the hood.
5.6.2
Cleaning agents
When using chemical cleaning agents, make sure you follow the general rules and suppliers recommendations regarding ventilation, protection of personnel, etc.
For separator bowl, inlet and outlet A chemical cleaning agent must dissolve the deposits quickly without attacking the material of the separator parts.
86
G0545121
G0545131
5.6 Cleaning
5 Service Instructions
For cleaning of lube oil separators the most important function of the cleaning agent is to be a good solvent for the gypsum in the sludge. It should also act as a dispersant and emulsifier for oil. It is recommended to use Alfa Laval cleaning liquid for lube oil separators which has the above mentioned qualities. Note that carbon steel parts can be damaged by the cleaning agent if submerged for a long time. Fuel oil sludge mainly consists of complex organic substances such as asphaltenes. The most important property of a cleaning liquid for the removal of fuel oil sludge is the ability to dissolve these asphaltenes. Alfa Laval cleaning liquid for fuel oil separators has been developed for this purpose. The liquid is water soluble, nonflammable and does not cause corrosion of brass and steel. It is also gentle to rubber and nylon gaskets in the separator bowl. Before use, dilute the liquid with water to a concentration of 3-5%. Recommended cleaning temperature is 50-70 C.
Alfa Laval cleaning liquid for fuel oil and lube oil separators
CAUTION
Skin irritation hazard Read the instructions on the label of the plastic container before using the cleaning liquid. Always wear safety goggles, gloves and protective clothing as the liquid is alkaline and dangerous to skin and eyes.
For operating mechanism Use 10% acetic acid solution to dissolve lime deposits. The acid should be heated to 80 C.
For parts of the driving devices Use white spirit, cleaning-grade kerosene or diesel oil.
87
S0008511
5 Service Instructions
5.6 Cleaning
Oiling (protect surfaces against corrosion) Protect cleaned carbon steel parts against corrosion by oiling. Separator parts that are not assembled after cleaning must be wiped and coated with a thin layer of clean oil and protected from dust and dirt.
5.6.3
Handle the bowl discs carefully so as to avoid damage to the surfaces during cleaning.
NOTE
Mechanical cleaning is likely to scratch the disc surfaces causing deposits to form quicker and adhere more firmly. A gentle chemical cleaning is therefore preferable to mechanical cleaning.
1.
2.
Let the discs remain in the cleaning agent until the deposits have dissolved. This will normally take between two and four hours. Finally clean the discs with a soft brush.
3.
CAUTION
Cut hazard Sharp edges on the separator discs may cause cuts.
Clean the discs with a soft brush
G0065841
88
G0065831
Remove the bowl discs from the distributor and lay them down, one by one, in the cleaning agent.
5 Service Instructions
5.7
5.7.1
To check at each oil change Check the teeth of both the worm wheel and worm for wear. See the Tooth appearance examples on page 91. Examine the contact surfaces and compare the tooth profiles. The gear may operate satisfactorily even when worn to some degree. Replace both worm wheel and worm at the same time, even if only one of them is worn. To avoid damaging the teeth when lifting the bowl spindle: push the worm wheel to one side first. Position the spindle in place before fitting the worm wheel. When replacing the gear, always make sure that the new worm wheel and worm have the same number of teeth as the old ones. See chapter 8.1 Technical data on page 170 for correct number of teeth.
G0205311
1 2
DANGER
Disintegration hazards Check that gear ratio is correct for power frequency used. If incorrect, subsequent overspeed may result in a serious breakdown.
Check the gear ratio (number of teeth) when replacing the gear
G0205411
89
5 Service Instructions
NOTE
Presence of metal chips in the oil bath is an indication that the gear is wearing abnormally.
Important! When using mineral-type oil in the worm gear housing, the presence of black deposits on the spindle parts is an indication that the oil base has deteriorated seriously or that some of the oil additives have precipitated. If pits are found on the worm gear, the cause could be that the additives are not suitable for this purpose. In all these cases it is imperative to change to a high-temperature oil. For further information, see chapter 8.5 Lubricants on page 180.
90
5 Service Instructions
Tooth appearance examples Satisfactory teeth: Uniform wear of contact surfaces. Surfaces are smooth. Good contact surfaces will form on the teeth when the gear is subjected to only moderate load during its running-in period.
Satisfactory teeth
G0538711
Worn teeth: Permissible wear is as a rule 1/3 of the thickness of the upper part of a tooth, provided that
G0538811
the wear is uniform over the whole of the flank of a tooth and all teeth are worn in the same way.
Worn teeth
Spalling: Small bits of the teeth have broken off, so-called spalling. This is generally due to excessive load or improper lubrication. Damage of this type need not necessitate immediate replacement, but careful checking at short intervals is imperative.
Spalling
Pitting: Small cavities in the teeth, so-called pitting, can occur through excessive load or improper lubrication. Damage of this type need not necessitate immediate replacement, but careful check at short intervals is imperative.
Pitting
91
G0539011
G0538911
5 Service Instructions
5.7.2 NOTE
Before adding or renewing lubricating oil in the worm gear housing, the information concerning different oil groups, handling of oils, oil change intervals etc. given in chapter 8.5 Lubricants on page 180 must be well known.
G0528311
1. 2. 3.
1.
Place a collecting tray under the drain hole, remove the drain plug and drain off the oil.
CAUTION
Burn hazards The lubricating oil and various machine surfaces can be sufficiently hot to cause burns.
G0641411
2.
Fill new oil in the worm gear housing. The oil level should be slightly above the middle of the sight glass. Oil volume: approx. 4,0 litres.
NOTE
During operation the oil level is normally just visible in the lower part of the sight glass. Too much or too little oil can damage the separator bearings.
The oil level at standstill must not be below the middle of the sight glass
G0639611
92
5.8 Vibration
5 Service Instructions
5.8
5.8.1
Vibration
Vibration analysis
Excessive vibration or noise indicates that something is incorrect. Stop the separator and identify the cause. Use vibration analysis instrument to periodically check and record the level of vibration. See the illustration where to take measurements. The level of vibration should not exceed 7,1 mm/s at full speed.
DANGER
Disintegration hazards If excessive vibration occurs, stop separator and keep bowl filled with liquid during rundown. The cause of the vibration must be identified and corrected before the separator is restarted. Excessive vibration can be due to incorrect assembly or poor cleaning of the bowl.
Measuring points for vibration analysis
93
G0582831
5 Service Instructions
5.9
5.9.1
Special-design bearings for the bowl spindle The bearings used for the bowl spindle are special to withstand the speed, vibration, temperature and load characteristics of highspeed separators. Only Alfa Laval genuine spare parts should be used. A bearing that in appearance looks equivalent to the correct may be considerably different in various respects: inside clearances, design and tolerances of the cage and races as well as material and heat treatment.
1. Outer race 2. Ball/roller 3. Inner race 4. Cage
G0587321
NOTE
Using an incorrect bearing can cause a serious breakdown with damage to equipment as a result. Do not re-fit a used bearing. Always replace it with a new one.
Dismantling For bearings where no driving-off sleeve is included in the tool kit, remove the bearing from its seat by using a puller. If possible, let the puller engage the inner ring, then remove the bearing with a steady force until the bearing bore completely clears the entire length of the cylindrical seat. The puller should be accurately centered during dismantling; otherwise, it is easy to damage the seating.
For bearings where no driving-off sleeve is included in the tool kit, use a puller when removing bearings
94
G0587411
5 Service Instructions
NOTE
Do not hit with a hammer directly on the bearing.
Cleaning and inspection Check shaft (spindle) end and/or bearing seat in the housing for damage indicating that the bearing has rotated on the shaft (spindle) and/or in the housing respectively. Replace the damaged part(s), if the faults cannot be remedied by polishing or in some other way. Assembly Leave new bearings in original wrapping until ready to fit. The anti-rust agent protecting a new bearing should not be removed before use. Use the greatest cleanliness when handling the bearings. To facilitate assembly and also reduce the risk of damage, first clean and then lightly smear the bearing seating on shaft (spindle) or alternatively in housing, with a thin oil.
When assembling ball bearings, the bearings must be heated in oil to max. 125 C.
NOTE
Heat the bearing in a clean container.
G0587611
Use only clean oil with a flash point above 250 C. The bearing must be well covered by the oil and not be in direct contact with the sides or the bottom of the container. Place the bearing on some kind of support or suspended in the oil bath.
The bearing must not be in direct contact with the container
95
G0587511
5 Service Instructions
There are several basic rules for assembling cylindrical bore bearings: Never directly strike a bearings rings, cage or rolling elements while assembling. A ring may crack or metal fragments break off. Never apply pressure to one ring in order to assemble the other. Use an ordinary hammer. Hammers with soft metal heads are unsuitable as fragments of the metal may break off and enter the bearing. Make sure the bearing is assembled at a right angle to the shaft (spindle).
If necessary use a driving-on sleeve that abuts the ring which is to be assembled with an interference fit, otherwise there is a risk that the rolling elements and raceways may be damaged and premature failure may follow.
Angular contact ball bearings Always fit single-row angular contact ball bearings with the wide shoulder of the inner race facing the axial load (upwards on a bowl spindle).
The wide shoulder of the inner race must face the axial load
S0116521
96
G0587711
5 Service Instructions
5.9.2
Before shutdowns
Before the separator is shut-down for a period of time, the following must be carried out: Remove the bowl, according to instructions in chapter 6 Dismantling/Assembly on page 99.
NOTE
The bowl must not be left on the spindle during standstill for more than one week. Vibration in foundations can be transmitted to the bowl and produce one-sided loading of the bearings. The resultant indentations in the ball bearing races can cause premature bearing failure.
Protect cleaned carbon steel parts against corrosion by oiling. Separator parts that are not assembled after cleaning must be wiped and protected against dust and dirt. If the separator has been shut-down for more than 3 months but less than 12 months, an Intermediate Service (IS) has to be made. If the shut-down period has been longer than 12 months, a Major Service (MS) should be carried out.
97
5 Service Instructions
98
6 Dismantling/Assembly
Contents
6.1 Introduction
6.1.1 6.1.2 6.1.3 General directions References to check points Tools 100 100 101 101 102 102 103 104 105 105 106 109
99
6 Dismantling/Assembly
6.1 Introduction
6.1
6.1.1
Introduction
General directions
The separator must be dismantled regularly for cleaning and inspection. The recommended intervals are stated in chapter 5.1.2 Maintenance intervals on page 45.
DANGER
Entrapment hazard Make sure that rotating parts have come to a complete standstill before starting any dismantling work.
G0246221
The revolution counter and the motor fan indicate if separator parts are rotating or not.
The revolution counter indicates if the separator still is rotating
The frame hood and heavy bowl parts must be lifted by hoist. Position the hoist directly above the bowl centre. Use an endless sling and a lifting hook with catch. These parts must be handled carefully. Do not place parts directly on the floor, but on a clean rubber mat, fibreboard or a suitable pallet.
NOTE
Never interchange bowl parts To prevent mixing of parts, e.g. in an installation comprising several machines of the same type, the major bowl parts carry the machine manufacturing number or its last tree digits.
100
6.1 Introduction
6 Dismantling/Assembly
6.1.2
In the text you will find references to the Check Point instructions in chapter 5. The references appear in the text as in the following example:
Check point
5.3.5 Disc stack pressure on page 61. In this example, look up check point Disc stack pressure in chapter 5 for further instructions.
6.1.3
Tools
Special tools from the tool kit must be used for dismantling and assembly. The special tools are specified in the Spare Parts Catalogue and are shown as illustrations together with the dismantling/assembly instructions.
NOTE
When lifting parts without weight specifications, always use lifting straps with a capacity of at least 500 kg.
101
6 Dismantling/Assembly
6.2
6.2.1
1. 2. 3. 4. 5.
O-ring Inlet pipe O-ring Support Connecting housing (with sight glass and pressure gauge) Protecting washer Height adjusting ring Frame hood Screw
6. 7. 8. 9.
102
G0690621
6 Dismantling/Assembly
6.2.2
Dismantling DANGER
Entrapment hazards
The revolution counter and the motor fan indicate if separator parts are rotating or not. 2. To avoid accidental start, switch off and lock power supply before starting any dismantling work.
The parts must be handled carefully. Dont place parts directly on the floor, but on a clean rubber mat, fibreboard or a suitable pallet. 1. Disconnect the water supply hose. Unscrew the inlet pipe clockwise and remove it. Left-hand thread!
2. Remove the inlet and outlet piping support, connection housing, protecting washer and height adjusting ring. 3. Loosen the hinged bolts and remove the frame hood. The bowl parts can remain very hot for a considerable time after the bowl has come to a standstill.
103
G0002721
S0051011
G0246221
1. Make sure that rotating parts have come to a complete standstill before starting any dismantling work.
6 Dismantling/Assembly
6.2.3
1. 2.
Assembly
Put the frame hood in place and clamp it with the hinged bolts. Lubricate the sealing rings for the inlet/outlet device with silicone grease. Renew the sealing rings at each Intermediate Service (IS). Fit the connection housing and inlet and outlet parts. Connect oil and water inlet and outlet parts.
3. 4.
5.
DANGER
Disintegration hazards When power cables have been connected, always check direction of rotation. If incorrect, vital rotating parts could unscrew causing disintegration of the machine.
104
G0002741
G0006821
6 Dismantling/Assembly
6.3
6.3.1
1. 2. 3. 4. 5. 6. 7. 8. 9.
Paring chamber cover (small lock ring) O-ring Upper paring disc Guide sleeve with gasket O-ring Gasket Gravity disc (or clarifier disc) Lock ring O-ring
Bowl hood with seal ring Top disc Oil paring disc Level ring O-ring Bowl discs Wing insert Bowl discs Distributor
105
G0690711
6 Dismantling/Assembly
6.3.2
1.
Dismantling
Unscrew the small lock ring (paring chamber cover) by using the special spanner. Left-hand thread!
S0107311
2. 3.
Remove the lock ring, paring disc, guide sleeve, gasket and gravity disc. Apply the brake and unscrew the large lock ring. Left-hand thread!
S0066911
NOTE
After removing the lock ring it must be kept lying horizontally or it may become distorted. Even the slightest distortion could make it impossible to refit.
106
G0642511
G0002921
6 Dismantling/Assembly
5. Screw the spindle plate into the lifting tool. Unscrew the spindle a few turns if the plate is not in contact with the lifting tool.
G0543731
6. Screw home the spindle with a wrench until the bowl hood loosens from the bowl body. 7. Remove the spindle plate from the lifting tool. 8. Lift off the bowl hood using hoist. Be careful not to scratch the bowl hood seal ring
CAUTION
Crush hazards If the top disc is stuck in the bowl hood, remove it now before it accidentally falls out.
S0111711
S0111311
107
G0539941
6 Dismantling/Assembly
9.
10. Screw the inlet pipe into the oil paring disc located above the level ring inside the top disc. Left-hand thread! Place the top disc onto wooden blocks to act as protection for the top disc edge and for falling level ring. Place a piece of wood between the tin hammer and the inlet pipe and then force out the level ring and the paring disc carefully from the top disc.
11. Fit the lifting tool into the distributor and lift the distributor with disc stack out of the bowl body by hoist.
12. Remove deposits and clean all parts thoroughly in a suitable cleaning agent. See chapter 5.6 Cleaning on page 86.
G0531951
S0117611
108
G0642621
6 Dismantling/Assembly
6.3.3
Assembly
Check point
5.3.3 Corrosion on page 57, 5.3.4 Cracks on page 60, 5.3.6 Erosion on page 62, 5.3.10 Lock ring; wear and damage on page 67. 1. Assemble the discs one by one on the distributor. The distributor has a guide rib for the correct positioning of the discs.
CAUTION
Cut hazard Sharp edges on the separator discs may cause cuts.
For correct number of discs above and below the wing insert when the machine was new, see the Spare Parts Catalogue. The number of bowl discs above the wing insert may be increased to adjust the disc stack pressure. 2. Fit the lifting tool to the distributor and lift the distributor with disc stack into the sliding bowl bottom using hoist.
S0117611
109
G0531951
G0603111
6 Dismantling/Assembly
3.
Check that the guide pin in the distributing cone (in line with guide lug B) fits into the recess on the underside of the distributor. The recess is in line with the disc guide rib (A).
Check point
5.3.9 Level ring on page 66. 5.3.8 Inlet pipe and oil paring disc on page 66. 4. Fit the oil paring disc and level ring with O-ring into the top disc. Make sure that the paring disc is positioned in correct direction (i.e. not upside down).
5.
Fit the top disc onto the distributor. The drilled assembly mark on the top disc must face the guide lug on the bowl body.
110
G0642821
G0642711
G0005821
6 Dismantling/Assembly
Check point
5.3.1 Bowl hood seal ring on page 56. 6. Fit the lifting tool to the bowl hood and lift it using hoist. Check that the seal rings of the bowl hood are properly fitted and lubricated. Lower the bowl hood straight down onto the disc stack, otherwise it may get stuck. Be careful not to scratch the bowl hood seal ring. For correct position of bowl hood, see next illustration.
7. Check that the guide recess on the bowl hood enters the guide lug in the bowl body.
111
G0006221
G0535621
G0539941
6 Dismantling/Assembly
8. 9.
Remove the lifting tool. Lubricate the lock ring threads, contact and guide surfaces with lubricating paste.
Check point
5.4.15 Lock ring; priming on page 80 (only at Major Service).
S0066911
Check point
5.3.5 Disc stack pressure on page 61.
NOTE
The assembly marks must never pass each other by more than 25 .
G0578131
112
G0642911
G0537241
6 Dismantling/Assembly
12. Assemble the upper paring disc and the guide sleeve to the small lock ring (paring chamber cover). Then fit the gravity disc and the lock ring assembly to the bowl hood.
Check point
5.3.8 Inlet pipe and oil paring disc on page 66. 13. Tighten the paring chamber cover using the spanner. Left-hand thread!
S0107311
113
G0642321
6 Dismantling/Assembly
6.4
6.4.1
1. Cap nut 2. Distributing cone 3. O-ring 4. Sliding bowl bottom 5. Rectangular ring 6. Screw 7. Bowl body 8. Nozzle 9. O-ring 10. Valve plug 11. Operating slide 12. Spring 13. O-ring 14. Spring support 15. Screw
114
G0690811
6 Dismantling/Assembly
6.4.2
Dismantling
2. Fit the lifting tool into the distributing cone and lift it out.
S0117611
3. Fit the lifting tool onto the sliding bowl bottom and lift it out by hoist.
S0103511
115
G0004021
G0533241
G0523131
G0523111
6 Dismantling/Assembly
5.
Fit the lifting tool onto the bowl body bottom. If necessary, unscrew the central screw.
Release the bowl body from the spindle by using the lifting tool as a puller. Turn the eye of the central screw of the lifting tool until the bowl body comes loose from the spindle taper. Turn the eye two more turns in order to avoid damaging the paring disc device. 6. Lift out the bowl body using hoist.
7. 8.
Turn the bowl body upside down. Loosen the screws for the spring support successively a little at a time. Remove the screws.
116
G0689021
G0533351
G0643021
6 Dismantling/Assembly
10. Remove the operating slide and place it with the valve plugs facing upwards.
11. Remove any thick deposits in the frame hood and clean all other parts thoroughly in a suitable cleaning agent. See chapter 5.6 Cleaning on page 86. The surfaces of the sludge space (shown with a thick line in the illustration) must not be damaged. Be cautious when cleaning. Do not use a steel tool but the sludge scraper of brass included in the set of tools.
G0523621
117
G0536611
G0004421
6 Dismantling/Assembly
6.4.3
Assembly
Check point
5.3.3 Corrosion on page 57, 5.3.4 Cracks on page 60, 5.3.6 Erosion on page 62, 5.3.7 Guide surfaces on page 64 (IS), 5.4.12 Guide surfaces on page 79 (MS), 5.3.11 Operating mechanism on page 69, 5.3.12 Operating slide on page 69, 5.3.13 Sliding bowl bottom on page 70, 5.3.14 Springs for operating mechanism on page 71. 1. Lubricate the guide surfaces of the bowl body and operating slide with lubricating paste. See chapter 8.5 Lubricants on page 180. Fit the operating slide onto the bowl body. Check that the guide pin in the bowl body enters the hole in the operating slide.
2.
NOTE
If there is too much lubrication paste applied, the surplus will collect between the operating slide and bowl body with risk for malfunction.
3.
4.
Tighten the screws for the spring support successively a little at a time. Finally tighten firmly (by hand).
118
G0004921
G0640311
Lubricate the screw threads and the guide surfaces of the spring support. See chapter 8.5 Lubricants on page 180.
6 Dismantling/Assembly
5. Wipe off the spindle top and nave bore in the bowl body. Apply a drop of oil to the tapered end of the spindle, smear it over the surface and wipe it off with a clean cloth.
Check point
5.3.2 Bowl spindle cone and bowl body nave on page 57.
6. Turn the bowl body and fit the lifting tool onto the bowl body bottom. Turn the handle at the top of the lifting tool so that the central screw is home. 7. Lower the bowl body by hoist until the central screw rests on the spindle top. Then screw up the central screw so that the bowl body sinks down onto the spindle.
G0533351 S0103511 G0533241 G0004021
8. Rotate the bowl body and align it so that the screw holes in the bowl body bottom are exactly above the holes in the operating device. Tighten the bowl body screws firmly.
9. Lubricate the guide surfaces of the bowl body and sliding bowl bottom with lubricating paste. See chapter 8.5 Lubricants on page 180. 10. Fit the lifting tool to the sliding bowl bottom and lift it into the bowl body by hoist.
119
G0285011
6 Dismantling/Assembly
11. Fit the distributing cone onto the sliding bowl bottom.
S0117611
Check that the guide pins on the underside of the distributing cone enter the recesses in the sliding bowl bottom. 12. Screw on the cap nut and tighten firmly. Left-hand thread!
120
G0523121
G0523131
6 Dismantling/Assembly
6.5
6.5.1
1. 2. 3. 4. 5. 6. 7. 8. 9.
Ring nut Control paring disc O-ring O-ring Distributing ring Gasket Screw Washer Screen
10. Rectangular ring 11. Distributing cover 12. Gasket 13. Sleeve 14. Rectangular ring (height adjusting ring)
Operating device
121
G0691821
G0692711
6 Dismantling/Assembly
6.5.2
1.
Dismantling
2.
3. 4. 5.
Ease off the ring nut. Remove the distributing cover together with the paring disc device. Dismantle the parts in the sequence appearing from the exploded view. Remove deposits and clean all parts thoroughly in a suitable cleaning agent. Pay special attention to the channels. See chapter 5.6 Cleaning on page 86. Check the parts for damage and corrosion.
G0692611
6.
122
G0692511
G0692031
6 Dismantling/Assembly
6.5.3
Assembly
1. Assemble the parts to the distributing cover in the sequence appearing from the exploded view. Ensure the parts are placed in positions defined by guides. 2. Fit the distributing cover with the paring disc assembly and the height adjusting ring (see arrow). Do not tighten the screws until the operating device has been fitted.
Check point
5.4.19 Control paring disc device; height position on page 83.
123
G0527311
G0692511
G0692621
6 Dismantling/Assembly
5.
124
G0692031
6 Dismantling/Assembly
6.6
6.6.1
125
G0643611
6 Dismantling/Assembly
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 13A. 13B. 13C. 13D. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.
Screw Protecting plate Screw Protecting guard O-ring Protecting collar Screw Spring washer Spring casing Deflector Ball bearing Ball bearing housing Axial buffer Split pin Wear ring Spring Spring support Buffer Screw plug Spring O-ring O-ring Bowl spindle Worm Spacing washer Ball bearing Lock washer Round nut Bushing O-ring Lock washer Round nut
126
6 Dismantling/Assembly
6.6.2 NOTE
Dismantling
Clean the space in the bowl casing thoroughly before starting to dismantle the bowl spindle to prevent contaminations falling down into the oil gear housing.
CAUTION
Burn hazards The lubricating oil and various machine surfaces can be hot and cause burns.
2. Unscrew and remove the protecting plate and the protecting guard. 3. Remove the O-ring and unscrew the protecting collar with e.g. a drift. Left-hand thread!
127
G0132211
G0520811
G0641411
6 Dismantling/Assembly
5.
6.
Separator with no built-on pump a. Remove the bearing shield and gasket.
Separator with built-on pump a. Remove the pipe connections from the pump. b. Remove the sleeve halves over the coupling.
c.
Loosen. but do not remove the stop screw positioned in the coupling half nearest the separator frame. Use a hexagon wrench. Turn the coupling drum by hand until the stop screw is in a convenient position.
128
G0662311
G0662121
G0520911
G0132411
6 Dismantling/Assembly
8. Remove the round nut and lock washer at the worm wheel shaft.
9. Remove the ball bearing and worm wheel fitted on the shaft.
129
G0521221
G0521111
G0521011
G0520921
6 Dismantling/Assembly
10. Lift out the bowl spindle by using the special lifting tool.
S0066811
11. 50 Hz separator: Remove the axial buffer from the frame. 60 Hz separator: The buffer can be removed from the spindle after the worm has been knocked off, see following text.
G0521511
12. Clamp the bowl spindle in a screw vice, protected with copper liners. 13. Remove the round nut and lock washer for the bottom bearing on spindle.
14. Pull off the ball bearing together with the spacing washer.
130
G0280211
G0521611
G0527431
6 Dismantling/Assembly
15. Knock off the worm by using a hammer and a soft drift. 16. 60 Hz separator: Remove the axial buffer.
17. Remove the screw plugs, springs and buffers. Then remove the spring casing.
18. Unscrew the deflector and remove the ball bearing housing. Left-hand thread!
S0079911
20. Clean all dismantled parts thoroughly in a degreasing agent and check for damage and corrosion.
131
G0643711
G0521811
G0521711
G0280111
6 Dismantling/Assembly
6.6.3
Assembly
When mounting ball bearings on the spindle as described below, the bearings must be heated in oil to max 125 C.
WARNING
Burn hazards Use protective gloves when handling the heated bearings.
NOTE
If any doubt how to mount roller bearings in a correct way, see the detailed description in chapter 5.9.1 Ball and roller bearings on page 94.
Check point
5.4.5 Buffer springs and ball bearing housing on page 74. 1. 2. Mount the upper ball bearing (6) onto the spindle. Make sure it enters its seat. Fit the bearing housing (7) and tighten the deflector (5). Left-hand thread! 3. Fit the spring casing (1), buffers (2), springs(3) and plugs (4). Make sure the buffers come to rest against the flats of the ball bearing housing. The final tightening of the plugs is preferably done when the spindle has been placed in the frame. 4. Fit the worm (8), spacing washer (9) and bottom ball bearing (10). Note: For 60 Hz separators, the axial buffer must be mounted on the spindle before the worm and ball bearing are mounted, see next illustration.
G0643811
5.
Finally fit the lock washer (11) and tighten the round nut (12).
132
6 Dismantling/Assembly
7. Carefully lower the spindle into the frame. Guide the bearing into the bottom bushing. If it does not completely enter its seat, tap the spindle top with a tin hammer.
S0066811
133
G0132411
G0527431
G0521511
6 Dismantling/Assembly
9.
10. Screw the protecting collar onto the spindle. Left-hand thread! Fit its O-ring, guard and protecting plate.
11. Fit the worm wheel with ball bearing onto the shaft. Match the worm wheel with the teeth on the worm of the bowl spindle. 12. Fit the ball bearing and lock washer onto the shaft and tighten the round nut.
S0066411
Check point
5.4.24 Worm wheel shaft; radial wobble on page 84, 5.4.3 Bowl spindle; radial wobble on page 72.
134
G0528021
G0520821
G0133421
6 Dismantling/Assembly
13. Fit the revolution counter. 14. Fit the bearing shield/built-on pump:
Separator with no built-on pump a. Fit the gasket and bearing shield. The parts can be fitted only in one position because of the asymmetrical positioned screw holes.
Separator with built-on pump a. Check that the key for the pump coupling half is fitted in the keyway in the worm wheel shaft. b. Fit the gasket and pump assembly.
G0520921 G0662121 G0662311
Be careful that the lipseal ring is not damaged by the shaft end and by the key in shaft. Check that the key is facing the keyway in the coupling half. c. Check that the clearance on each side of the coupling flexible element is 2 mm. Tighten the stop screw in the coupling half with a hexagon wrench. Check that the holders for the lipseal rings are located so that the sleeve halves can easily be fitted.
d. Mount the sleeve halves over the coupling. e. Refit the pump connections.
135
G0520911
6 Dismantling/Assembly
15. Pour oil into worm gear housing. The oil level should be slightly above the middle of the sight glass. For correct oil volume, see chapter 8.1 Technical data on page 170. For recommended oil brands, see chapter 8.5.3 Recommended oil brands on page 183.
Check point
G0643911
136
6 Dismantling/Assembly
6.7
6.7.1
137
G0644011
6 Dismantling/Assembly
1. Screw 2. Coupling nave 3. Coupling disc 4. Elastic plate 5. Coupling disc 6. Friction block 7. Friction pad 8. O-ring 9. Round nut 10. Lock washer 11. Ball bearing 12. Spacing ring 13. Ball bearing 14. Nave 15. Worm wheel shaft 16. Frame 17. O-ring 18. Sealing washer 19. Seal ring 20. Ball bearing 21. Worm wheel 22. Ball bearing 23. Lock washer 24. Round nut
138
6 Dismantling/Assembly
6.7.2
Dismantling DANGER
Entrapment hazards
The revolution counter and the motor fan indicate if separator parts are rotating or not. 2. To avoid accidental start, switch off and lock power supply before starting any dismantling work.
The parts must be handled carefully. Dont place parts directly on the floor, but on a clean rubber mat, fibreboard or a suitable pallet. If the bowl spindle has been removed according to earlier description, points 1-5 below are already done. In this case proceed with point 6. 1. Drain the oil from the worm gear housing.
CAUTION
Burn hazards The lubricating oil and various machine surfaces can be hot and cause burns.
Separator with no built-on pump a. Remove the bearing shield and gasket.
G0520911
139
G0641411
S0051011
G0246221
1. Make sure that rotating parts have come to a complete standstill before starting any dismantling work.
6 Dismantling/Assembly
Separator with built-on pump a. Remove the pump assembly. See the dismantling instructions for the vertical driving device on page 129 for a detailed description.
3.
4.
Remove the round nut and lock washer at the worm wheel shaft.
5.
Remove the ball bearing and worm wheel fitted on the shaft.
140
G0521211
G0521111
G0521011
G0520921
6 Dismantling/Assembly
6. Pull off the ball bearing from the worm wheel. Use a washer as a support for the puller.
7. Remove: the electric motor (1) the elastic plate (2) the friction blocks (3). If disconnecting the motor cables, note the positions of cables in the terminal box to reconnect correctly (for correct direction of rotation).
G0641011
141
G0526011
G0547611
6 Dismantling/Assembly
9.
Dismantle the nave in the following way: remove the screws (1) and then the coupling disc (2) unscrew the round nut (3) and remove the lock washer put the coupling disc in place (4) again and pull off the nave with a 3/8 - 16 UNC screw (5).
10. Remove the sealing washer using two screws with threads 1/4 - 20 UNC.
142
G0522921
G0526131
6 Dismantling/Assembly
11. Remove the seal ring by using a drift. 12. Remove deposits and clean all parts thoroughly in a suitable cleaning agent. See chapter 5.6 Cleaning on page 86.
6.7.3
Assembly
1. Lubricate the O-ring on the sealing washer periphery and the sealing ring with silicone grease. Fit the sealing washer in the frame and check that the seal ring is fitted in the correct direction, as illustrated.
Check point
5.4.6 Coupling friction pads on page 75. 2. Apply ball bearing grease into the bearings (fill about 1/3 of the free volume in each bearing). Note that no grease must be packed in the nave proper, as superfluous grease might ooze out of the nave and adhere to the friction blocks. 3. Fit the nave, bearings and spacing ring, lock washer and the round nut.
S0066411
4. Fit the O-ring onto the nave and fasten the coupling disc. Put the friction blocks in place inside the coupling drum.
143
G0527931
G0522921
G0525111
6 Dismantling/Assembly
5.
NOTE
Before fitting the worm wheel, mount the bowl spindle into the separator frame if removed.
Check point
5.4.23 Worm wheel and worm; wear of teeth on page 83. 6. Heat the ball bearing and fit it on the worm wheel. When mounting the ball bearings on the worm wheel and shaft, the bearings must be heated in oil to max. 125 C.
G0547711
WARNING
Burn hazards Use protective gloves when handling the heated bearings.
NOTE
If any doubt how to mount roller bearings in a correct way, see the detailed description in chapter 5.9.1 Ball and roller bearings on page 94.
144
G0528111
6 Dismantling/Assembly
The remaining description in this section implies that the bowl spindle is mounted in the frame. If not, proceed with the assembly instruction for the vertical driving device in chapter 6.6.3 Assembly on page 133. 7. Fit the worm wheel with ball bearing onto the shaft. Match the worm wheel with the teeth on the worm of the bowl spindle. 8. Fit the ball bearing and lock washer onto the shaft and tighten the round nut.
S0066411
Check point
5.4.24 Worm wheel shaft; radial wobble on page 84, 5.4.3 Bowl spindle; radial wobble on page 72. 9. Fit the revolution counter. 10. Fit the bearing shield/built-on pump: Separator with no built-on pump a. Fit the gasket and bearing shield. The parts can be fitted only in one position because of the asymmetrical positioned screw holes.
G0528021 G0520921 G0520911
Separator with built-on pump a. Fit the gasket and pump assembly. See the assembly instructions on page 136 for a detailed description.
145
6 Dismantling/Assembly
11. Pour oil into worm gear housing. The oil level should be slightly above the middle of the sight glass. For correct oil volume, see chapter 8.1 Technical data on page 170. For recommended oil brands, see chapter 8.5.3 Recommended oil brands on page 183.
Check point
5.4.11 Elastic plate in coupling on page 77. 13. Fit the electric motor.
G0528211
DANGER
Disintegration hazards When power cables have been connected, always check direction of rotation. If incorrect, vital rotating parts could unscrew causing disintegration of the machine.
146
G0643911
Check point
6 Dismantling/Assembly
6.8
6.8.1
147
G0662721
6 Dismantling/Assembly
1. 2. 3. 4. 5. 6. 7. 8. 9.
Plate Drive screw Snap ring Washer Seal ring O-ring Sleeve Key Flexible coupling 9A. Tooth rim (flexible element) 9B. Stop screw
20. Bearing 21. Wear gasket 22. Impeller 23. Wear gasket 24. Bearing 25. Pump housing 26. O-ring 27. Valve cone 28. Guide pole 29. Spring 30. Gasket 31. Cover 32. Impeller 33. Bearing 33A. Bushing 34. O-ring 35. Washer 36. Nut 37. Screw 38. Spacer 39. Shield 40. Screw
10. Tubular spring pin 11. Screw 12. Nut 13. Sleeve half 14. Screw 15. Bearing shield 16. Sleeve 17. O-ring 18. Seal ring 19. Bearing 19A. Bushing
148
6 Dismantling/Assembly
6.8.2
Dismantling
The oil feed pump should be dismantled for inspection of parts with respect to wear and cavitation damage. 1. Drain the oil from the worm gear housing.
CAUTION
Burn hazards Lubricating oil and various machine surfaces can be hot and cause burns.
2. Remove the pipe connections from the pump. 3. Remove the sleeve halves over the coupling.
4. Drive out the tubular spring pin, positioned in the coupling half nearest the pump. Turn the coupling drum by hand until the pin is in a convenient position.
5. Loosen, but do not remove the stop screw positioned in the other coupling half with a hexagon wrench.
149
G0662311
G0662211
G0662121
G0641411
6 Dismantling/Assembly
6.
Undo the four screws holding the pump shield and remove the shield.
7.
Insert two screws (3/8-16 UNC) into the centre hole of the impeller shafts. Use the screws as a handle to withdraw the impellers.
8. 9.
Loosen the screws for the bearing shield, but do not remove them. Remove the coupling by pulling the complete pump outwards a short distance until the coupling can be loosened from the worm wheel shaft. Take care not to damage the lipseal ring.
G0662611
150
G0662511
G0662411
6 Dismantling/Assembly
6.8.3
1. Remove deposits and clean all parts thoroughly in a suitable cleaning agent. See chapter 5.6 Cleaning on page 86. 2. Examine following parts:
Bushings (2) Renew the bushings if they are scratched or if there is a play between any impeller shaft and a bushing.
Impeller shafts (5) Check the impeller shafts for grooves. Polish or renew if necessary.
Wear gaskets (3) Renew the wear gaskets if any surface is rough, cracked or dented by the impellers. Relief/safety valve (6) Examine the sealing surfaces on the valve cone and valve seat in the shield. Grind or renew if necessary.
1. 2. 3. 4. 5. 6. Flexible coupling Bushing Wear gasket Lipseal ring Impeller shaft Relief/safety valve
G0662811 G0661811
Flexible coupling (1) Dismantle and examine the coupling parts. If necessary, renew the flexible element or the complete coupling.
151
6 Dismantling/Assembly
Lipseal rings (4) Renew the lipseal rings at MS-service. Note: Turn the rings the right way round, see pos. A in the illustration.
6.8.4
1. 2.
Assembly
Check that the lipseal rings are correctly mounted, see above. Assemble the coupling. The parts must not be pushed together too hard. The flexible element is provided with projections to ensure that the correct clearance is maintained in the coupling, and these must not be deformed.
3.
Fit the coupling in position on the worm wheel shaft with the keyway facing the key.
4.
152
G0662611
G0661811
G0662921
6 Dismantling/Assembly
5. Refit the impellers. Check that the hole for the tubular pin is exactly opposite the corresponding hole in the coupling.
7. Check the axial play with a liner (B). The total axial play (A) must be 0,1 - 0,3 mm. If the play is too large even though the wear gaskets have been renewed, it can be compensated by adding a brass leaf liner. If the play is too small, grind off the bearing (1).
A. B. 1. 2.
153
G0661911
G0593831
G0662211
G0662011
6 Dismantling/Assembly
9.
Fit the pump shield. (Four screws, four washers and four nuts.)
10. Check that the clearance on each side of the coupling flexible element is 2 mm. Tighten the stop screw in the coupling half nearest the separator frame with a hexagon wrench. Check that the holders for the lipseal rings are located so that the sleeve halves can easily be fitted.
G0662311
11. Mount the sleeve halves over the coupling. 12. Refit the pipe connections.
13. Pour oil into worm gear housing. The oil level should be slightly above the middle of the sight glass. For correct oil volume, see chapter 8.1 Technical data on page 170. For recommended oil brands, see chapter 8.5.3 Recommended oil brands on page 183.
G0643911
154
G0662121
G0662411
7 Trouble-tracing
Contents
7.1 Mechanical function
7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 7.1.6 7.1.7 7.1.8 7.1.9 Separator vibrates Smell Noise Speed too low Speed too high Starting power too low Starting power too high Starting time too long Retardation time too long 158 158 159 159 159 160 160 161 161 162 162
Trouble-tracing
163
Liquid flows through the bowl casing drain and/or sludge outlet 163 Bowl opens accidentally during operation Bowl fails to open for sludge discharge Unsatisfactory sludge discharge 164 164 165 166 166 166
If the problem is not solved in the system documentation continue with this chapter.
Oil discharges through water outlet = Broken water seal 167 168 168
157
7 Trouble-tracing
7.1
7.1.1 NOTE
Mechanical function
Separator vibrates
Some vibration is normal during the starting and stopping sequences when the separator passes through its critical speeds.
DANGER
Disintegration hazards If excessive vibration occurs, stop separator and keep bowl filled with liquid during rundown. The cause of the vibration must be identified and corrected before the separator is restarted. Excessive vibration may be due to incorrect assembly or poor cleaning of the bowl.
Cause Bowl is out of balance due to: - poor cleaning - incorrect assembly - incorrect disc stack compression - bowl assembled with parts from other separators Uneven sludge deposits in the sludge space Height adjustment of the oil paring disc is incorrect Wrong height adjustment of operating device/bowl spindle Bowl spindle bent (max 0,04 mm) Bearing is overheated, damaged or worn Vibration dampers in frame feet are worn out Spindle top bearing spring broken
Corrective actions Dismantle the separator and check the assembly and cleaning
Page 109
106
82
83
Renew the bowl spindle Renew all bearings Renew all rubber cushion
72 126, 138 55
126
158
7 Trouble-tracing
7.1.2
Cause
Smell
Corrective actions None Page
Normal occurrence during start while the friction blocks are slipping Brake is applied Oil level in gear housing too low Bearing is overheated
Release the brake Check oil level and add oil if necessary Renew all bearings
38 126, 138
7.1.3
Cause
Noise
Corrective actions Check oil level and add oil if necessary Measure and adjust the height Page 38 82
Oil level in gear housing too low Height adjustment of the oil paring disc is incorrect Wrong height adjustment of operating device/bowl spindle Worm wheel and worm are worn Bearing is overheated, damaged or worn Incorrect play between coupling pulley and elastic plate
83
Renew worm wheel and worm Renew all bearings Adjust the play
89 126, 138 77
7.1.4
Cause
Brake is applied Coupling friction pads are oily or worn Bowl is not closed or leaking Motor failure Bearing is overheated, damaged or worn Incorrect gear transmission (60 Hz gear for 50 Hz power supply)
159
7 Trouble-tracing
7.1.5
Cause
In the event of overspeed, examine the bowl for possible deformation. The separator must not be started before the effects of the fault have been corrected. Contact your Alfa Laval representative. Frequency of power supply (50/60 Hz) Check
7.1.6
Cause
Incorrect gear transmission (60 Hz gear for 50 Hz power supply) Incorrect friction blocks (60 Hz coupling for 50 Hz power supply) Friction pads are oily or worn Motor failure
75
160
7 Trouble-tracing
7.1.7
Cause
After immediate stop, install correct transmission Incorrect friction blocks (50 Hz coupling for 60 Hz power supply) DANGER
After immediate stop change the friction blocks to suit the power supply frequency Brake is applied Wrong height adjustment of operating device/bowl spindle Worm wheel and worm are worn Release the brake Measure and adjust the height
75
83
Replace
Repair the motor Renew all bearings Change electrical phase connections to the motor
7.1.8
Cause
Brake is applied Friction pads are oily or worn Height position of oil paring disc or operating device is incorrect Motor failure Bearing is damaged or worn
126, 138
161
7 Trouble-tracing
7.1.9
Cause
126, 92 92
162
7 Trouble-tracing
7.2
7.2.1
Cause Sludge discharge in progress Strainer in operating water line is clogged or pressure is too low
Channels in operating device are clogged Seal rings in operating device are defective Sludge deposits on operating slide Seal ring at gravity disc or small lock ring (paring chamber cover) defective Paring chamber cover (small lock ring) defective Seal ring in the bowl hood defective or sealing surface of sliding bowl bottom is damaged Seal ring of the sliding bowl bottom defective Valve plugs are defective Displacement water volume too large Bowl speed too low
121
Clean Replace
... 105
105
Renew the seal ring. Polish the surface on sliding bowl bottom or replace
105
Smoothen sealing edge of the sliding bowl bottom or renew it Renew all valve plugs Check water supply and filling time See 7.1.4
70
69
159
163
7 Trouble-tracing
7.2.2
Cause
Strainer in the operating water supply is clogged No water in the operating water system
Check the operating water system and make sure the valve(s) are open Correct
Water connections to the separator are incorrectly fitted Nozzle in operating slide clogged
Clean the nozzle. Carry out an Intermediate Service (IS) Clean Renew the square-sectioned ring. Carry out an Intermediate Service (IS) Renew all plugs. Carry out an Intermediate Service (IS) Rectify 70
Sludge deposits on operating slide Square-sectioned ring in sliding bowl bottom is defective Valve plugs are defective
69
7.2.3
Cause Strainer in the operating water supply is clogged Water pressure too low Water flow too low Seal rings in operating device defective Seal ring in the operating slide is defective
Check the opening water pressure Check the opening water flow Renew the seal rings Renew the seal ring. Carry out an Intermediate Service (IS)
172
121 114
164
7 Trouble-tracing
7.2.4
Cause
Water pressure too low Water flow too low Valve plugs in operating slide too high Sludge deposits in the operating system
165
7 Trouble-tracing
7.3
7.3.1
Cause
Gravity disc hole is too small Incorrect separation temperature Throughput too high Disc stack is clogged Sludge space in bowl is filled
159
7.3.2
Cause
Gravity disc hole is too large Seal ring on top of the heavy phase paring disc defective Seal ring at gravity disc or small lock ring (paring chamber cover) defective Disc stack is clogged
88
166
7 Trouble-tracing
7.3.3
Cause Gravity disc hole is too large Incorrect separation temperature Throughput too high Valves in clean oil outlet line closed Sealing water volume too small Seal ring at gravity disc or small lock ring (paring chamber cover) defective Seal ring in the bowl hood defective or sealing surface of sliding bowl bottom is damaged Seal ring of the sliding bowl bottom defective Disc stack is clogged Bowl speed too low Bowl incorrectly assembled
Renew the seal ring. Polish the surface on sliding bowl bottom or replace
105
Smoothen sealing edge of the sliding bowl bottom or renew it Clean disc stack See 7.1.4 Check and rectify
70
88 159 105
167
7 Trouble-tracing
7.4
7.4.1
Cause
Incorrect separation temperature Throughput too high Disc stack is clogged Sludge space in bowl is filled
88 88
159
7.4.2
Cause
Valves in outlet line closed Seal rings on top of the heavy phase paring disc defective Disc stack is clogged Bowl incorrectly assembled
88 105
168
8 Technical Reference
Contents
8.1 Technical data 8.2 Connection list
8.2.1 8.2.2 Separator without pump Separator with built-on pump 170 8.6.10 Cover interlocking switch 201 202 202 204 207
Component description and signal processing 176 Function graph and running limitations 178 179
180 180 182 183 186 188 188 189 190 191 193 194 196 198 200
8.6 Drawings
8.6.1 8.6.2 8.6.3 8.6.4 8.6.5 8.6.6 8.6.7 8.6.8 8.6.9 Basic size drawing, separator with built-on pump Dimensions of connections, separator with built-on pump Basic size drawing, separator without pump Dimensions of connections, separator without pump Foundations Gravity disc nomogram Electric motor Electric motor Machine plates and safety labels
169
8 Technical Reference
8.1
Technical data
NOTE
The separator is a component operating in an integrated system including a monitoring system. If the technical data in the system description does not agree with the technical data in this instruction manual, the data in the system description is the valid one.
881034-01-08 MOPX 205 TGT-24 Intended for both land and marine applications. Continuous purification of fuel oil or lubrication oil from solid particles and water Continuous clarification of fuel oil or lubrication oil from solid particles and water
The flash point of the oil to be separated must be above 60 C. Density of operating liquid, max. Density of sediment, max. Density of feed, max. Hydraulic capacity Feed temperature, min./max. Ambient temperature, min./max. Bowl speed, max. 1 000 2 362 1 100 4 900 0 - 100 5 - 55 7 607 7 537 Motor shaft speed, max. 1 500 1 800 Revolution counter 118-125 142-150 No. of teeth; - on worm, 50 Hz - on worm, 60 Hz - on worm wheel, 50 Hz - on worm wheel, 60 Hz Lubricating oil volume 14 16 71 67 approx. 4,0 litres kg/m3 kg/m3 kg/m3 litres/hour C C r/min. at 50 Hz r/min. at 60 Hz r/min. at 50 Hz r/min. at 60 Hz r/min. at 50 Hz r/min. at 60 Hz
170
8 Technical Reference
Motor power rating Power consumption, max. Power consumption, idling Power consumption, at max. capacity Discharge volume Discharge interval, min. Discharge interval, max. Bowl volume Starting time Stopping time with brake Max. running time without flow - empty bowl - filled bowl Sound pressure level Vibration level, separator in use, max. Weight of separator (without motor) Weight of bowl
4 6,5 2,2 2,4 3,1 1 240 3,1 2 - 2,5 3,5 - 4,5 180 180 73 7,1 430 56
kW kW (at starting up) kW kW litres fixed discharge volume minute minutes litres minutes minutes minutes minutes dB(A) ISO 3744 mm/s (RMS) kg kg
The materials in contact with process fluid (excluding seals and O-rings) are brass, bronze and stainless steel. Cast iron frame.
171
8 Technical Reference
8.2
8.2.1
Connection list
Separator without pump
Requirements/limits
206
Inlet for liquid seal or displacement liquid Outlet for light phase (oil) - Pressure
220
221 222
Outlet for heavy phase (water) Outlet for solid phase To be installed in such a way that the frame top part cannot fill with sludge. (Guidance of sludge pump or open outlet). Approx. 3,1 litres Min. 1 minute Max. 4 hours
372
Inlet for discharge liquid - Pressure - Consumption per discharge - Quality requirements Min. 200 kPa, max. 600 kPa 6 litres See 8.4 Water quality on page 179
376
Inlet for make-up liquid - Pressure - Quality requirements Min. 140 kPa, max. 240 kPa See 8.4 Water quality on page 179
Outlet for operating liquid (water) Drain of frame top part, lower Drain of frame top part, upper
172
8 Technical Reference
Requirements/limits
5% (momentarily 10% during a period of maximum 5 seconds) See 8.3 Interface description and 8.6.10 Cover interlocking switch on page 201.
760
8.2.2
Description Inlet for process liquid, to pump Outlet for process liquid, from pump Inlet for process liquid, to separator - Allowed temperature
Requirements/limits
206
Inlet for liquid seal and displacement liquid Outlet for light phase (oil) - Pressure
220
221 222
Outlet for heavy phase (water) Outlet for solid phase To be installed in such a way that the frame top part cannot fill with sludge. (Guidance of sludge pump or open outlet). Approx. 3,1 litres Min. 1 minute Max. 4 hours
173
8 Technical Reference
Description Inlet for discharge liquid - Pressure - Consumption per discharge - Quality requirements
Requirements/limits
Min. 200 kPa Max. 600 kPa 6 litres See 8.4 Water quality on page 179
376
Inlet for make-up liquid - Pressure - Quality requirements Min. 140 kPa, max. 240 kPa See 8.4 Water quality on page 179
Outlet for operating liquid (water) Drain of frame top part, lower Drain of frame top part, upper Motor for separator - Deviation from nominal frequency 5% (momentarily 10% during a period of maximum 5 seconds) See 8.3 Interface description and 8.6.10 Cover interlocking switch on page 201.
760
174
8 Technical Reference
8.3
Interface description
8.3.1
General
In addition to the Connection List this document describes limitations and conditions for safe control, monitoring and reliable operation. At the end of the document a function graph and running limitations are found.
8.3.2
Definitions
Stand still (Ready for start) means: The machine is assembled correctly. All connections are installed according to Connection List, Interconnection Diagram and Interface Description.
Start means: The power to the separator is on. The acceleration is supervised to ensure that a certain speed has been reached within a certain time. See technical data.
Normal stop means: Stopping of the machine at any time with brake applied. The bowl must be kept filled.
Safety stop means: The machine must be stopped in the quickest and safest way due to vibrations or process reasons. Comply to following conditions:
175
8 Technical Reference
The bowl must be kept filled. Sludge ejection must not be made. The machine must not be restarted before the reason for the safety stop has been investigated and action has been taken. In case of emergency condition in the plant, the machine must be stopped in a way that is described in EN 418.
8.3.3
176
8 Technical Reference
Signal Processing The circuit is closed when the frame hood of the separator is closed. The interlocking switch should be connected so that starting of the motor is prevented when the separator hood is not closed.
177
8 Technical Reference
8.3.4
A. B. C. D. E.
Stand still Starting mode Running mode Stop mode Safety stop mode
G0543211
178
8 Technical Reference
8.4
General
Water quality
Specific requirements regarding the purity of water are necessary. Deposits must not be allowed to form inside the separator. Erosion and corrosion of the PX mechanism must also be prevented.
The four requirements below are of fundamental importance. For test methods, contact an Alfa Laval representative. If these demands cannot be met, the water should be pre-treated in accordance with Alfa Lavals recommendations. Alfa Laval accepts no liability for consequences arising from unsatisfactory purified operating water supplied by the customer. Suspended particles Content of suspend substances: Less than 0,001 percentage of volume. Turbidity-free water, solids content <0,001 percentage of volume. Due to the centrifugal force, any suspended particles present in the water will separate out in the operating mechanism, causing the valves to clog and the system to breakdown. A mere 0,001 percentage of volume solids content in the operating water produces 10 ml of precipitate in two days when using as little as 20 lit/h of operating water. Max. particle size: 50 m. Total hardness Less than 10 dH (180 mg CaCO3/litre). If the water is hard (i.e. 10 dH or 12,5 E), in time chalk deposits build up around the operating mechanism including the valves. The build-up of deposits accelerates with increased operating temperature and low discharge frequency. The harder the water is, the more severe these effects become. Chloride content Less than 100 ppm NaCl (60 mg Cl/lit). Chloride ions contribute to corrosion on the separator surfaces in contact with the operating water, including the spindle. Corrosion is a destructive process that is accelerated by increased separating temperature, low discharge frequency, low pH and high chloride ion concentration. A chloride concentration above 60 mg/litre is definitely not recommended. pH value pH >6 Increasing acidity (lower pH) increases corrosion; this is accelerated by increased temperatures, low discharge frequency and high chloride ion content.
179
8 Technical Reference
8.5 Lubricants
8.5
8.5.1
Lubricants
Lubrication chart, general
Lubricating points Bowl spindle ball bearings and buffers are lubricated by oil mist Bowl spindle taper
Lubricants Lubricating oil as specified in 8.5.2 Recommended lubricating oils on page 182 Lubricating oil (only a few drops for rust protection) Lubricating oil Pastes as specified in 8.5.4 Recommended lubricants on page 186 If not specified otherwise, follow the suppliers recommendation about method of application Grease as specified in 8.5.4 Recommended lubricants on page 186 The bearings are packed with grease and sealed and need no extra lubrication Follow manufacturers instructions.
Buffers of bowl spindle Bowl: Sliding contact surfaces and pressure loaded surfaces such as lock rings, threads of lock rings, bowl hood, and cap nut Rubber seal rings
Alfa Laval Lubricating Oil Groups: Group A oil: a high quality gear oil on paraffin base with stable AW (anti wear) additives. Group B oil: a high quality gear oil on paraffin base with stable EP (extreme pressure) additives. Group D oil: a synthetic base oil with additives stable at high operating temperatures.
Do not mix different oil brands or oils from different oil groups. Always use clean vessels when handling lubricating oil.
180
8.5 Lubricants
8 Technical Reference
Great attention must be paid not to contaminate the lubricating oil. Of particular importance is to avoid mixing of different types of oil. Even a few drops of motor oil mixed into a synthetic oil may result in severe foaming. Any presence of black deposits in a mineral type oil is an indication that the oil base has deteriorated seriously or that some of the oil additives have precipitated. Always investigate why black deposits occur. If it is necessary to change from one group of oil brand to another it is recommended to do this in connection with an overhaul of the separator. Clean the gear housing and the spindle parts thoroughly and remove all deposits before filling the new oil.
NOTE
Always clean and dry parts (also tools) before lubricants are applied.
NOTE
Check the oil level before start. Top up when necessary. Oil volume see 8.1 Technical data on page 170.
It is of utmost importance to use the lubricants recommended in our documentation. This does not exclude, however, the use of other brands, provided they have equivalently high quality properties as the brands recommended. The use of oil brands and other lubricants than recommended, is done on the exclusive responsibility of the user or oil supplier.
Applying, handling and storing of lubricants Always be sure to follow lubricant manufacturers instructions.
181
8 Technical Reference
8.5 Lubricants
8.5.2
Three different groups of lubricating oils are approved for this separator. They are designated as Alfa Laval lubricating oil groups A, B and D. The numerical value after the letter states the viscosity grade. The corresponding commercial oil brands are listed in chapter 8.5.3 Recommended oil brands on page 183. Ambient temperature C Alfa Laval lubricating oil group A/220, B/220 D/220 Time in operation Oil change interval 1 000 - 1 500 h 2 000 h
Note: In a new installation or after change of gear transmission, change oil after 200 operating hours. When the separator is operated for short periods, lubricating oil must be changed every 12 months even if the total number of operating hours is less than stated in the recommendations above. Check and prelubricate spindle bearings on separators which have been out of service for 6 months or longer. In seasonal operation: change oil before every operating period.
182
8.5 Lubricants
8 Technical Reference
8.5.3
Viscosity grade VG (ISO 3448/3104) Viscosity index VI (ISO 2909) Manufacturer Castrol Esso Standard Oil/ Svenska Statoil/Exxon Lubmarine/Beijer (ELF Brand designation according to ELF) Mobil Nyns Optimol lwerke Q8/Kuwait (Gulf) Shell
220 > 92
DTE Oil BB TD EX 220 Ultra 220 Harmony AW 220 Tellus C 220 Tellus 220 Regal R&O 220 Paper Machine HD 220
Texaco/
183
8 Technical Reference
8.5 Lubricants
Viscosity grade VG (ISO 3448/3104) Viscosity index VI (ISO 2909) Manufacturer Bel Ray BP Castrol Chevron
220 > 92
Designation 100/06-220 Energol GR-XP 220 Alpha SP 220 Ultragear 220 (NL Gear Compound 220) CLP 220 Spartan EP 220
DIN 51517, part 3 Esso Standard Oil/ Svenska Statoil/Exxon Fina/Petrofina ISO/DIS 6743/6 Lubmarine/Beijer (ELF Brand designation according to ELF) Mobil
Mobilgear 630 (Mobilgear SHC 220) (GL 220) Optigear BM 220 (5150) Goya 220 (Lorina 220) Omala 220 Delima HT 220 Meropa 220 IGP-152 according to TU 38.101413-90
184
8.5 Lubricants
8 Technical Reference
Viscosity grade VG (ISO 3448/3104) Viscosity index VI (ISO 2909) Manufacturer Alfa Laval
Designation 542690-80 542690-81 542690-82 542690-83 Enersyn HTX 220 Alpha Synt T 220 Epona SA 220 20 litres 4 litres 208 litres 1 litre
185
8 Technical Reference
8.5 Lubricants
8.5.4
Recommended lubricants
Manufacturer Gleitmolybdn
Designation Gleitmo 805 K or 805 K varnish 901 Gleitmo Paste G rapid Molykote paste1000 spray D321 R varnish D321 R Antiscuffing paste (ASP) Wolfracoat C paste
Application
Dow Corning
Rocol Klueber
Russian Standard
Silicone grease Manufacturer Dow Corning Designation Molykote 111 compound 100 g 25 g Silicone paste 750 Alfa Laval No.
539474-02 539474-03
Gleitmolybdn
Wacker
186
8.5 Lubricants
8 Technical Reference
Manufacturer BP
Designation Energrease MMEP2 Energrease LS2 Spheerol SW2 EP Spheerol EPL2 Duralith grease EP2 Beacon EP2 Mobilith SHC 460 Mobilux EP2 Gulflex MP2 Rembrandt EP2 Cailithia EP Grease T2 Alvania EP Grease 2 or R.A LGEP2 or LGMT2 Multifak AF B2 Multifak premium 2,3 Fiol 2M, Litol 24 TU 38.201.188
Castrol
Gulf Q8 Shell
SKF Texaco
Russian Standard
187
8 Technical Reference
8.5 Lubricants
188
8.6 Drawings
8 Technical Reference
8.6
8.6.1
Drawings
Basic size drawing, separator with built-on pump
A.
B.
Maximum vertical displacement at the solid phase connection during operation: 10 mm.
C.
189
G0685011
8 Technical Reference
8.6 Drawings
8.6.2
Data for connections, see chapter 8.2 Connection list on page 172. All connections to be installed non-loaded and flexible. Connections 201.3 and 220 are turnable.
190
G0684911
8.6 Drawings
8 Technical Reference
8.6.3
A.
B.
C.
191
G0685021
8 Technical Reference
8.6 Drawings
8.6.4
Data for connections, see chapter 8.2 Connection list on page 172. All connections to be installed non-loaded and flexible. Connections 201 and 220 are turnable.
192
G0684921
8.6 Drawings
8 Technical Reference
193
8 Technical Reference
8.6 Drawings
8.6.5
Foundations
A.
B. C. D. E.
Min. lifting capacity required when doing service: 100 kg Recommended speed for lifting: Low speed 0,5-1,5 m/min. High speed 2-6 m/min. Max. height of largest component incl. lifting tool 4 holes 18 for anchorage Center of separator bowl Service side
Recommended free floor space for unloading when doing service No fixed installations within this area. Center of gravity (without motor) Vertical force not exceeding 10 kN/foot Horizontal force not exceeding 10 kN/foot
194
G0684811
8.6 Drawings
8 Technical Reference
8.6.6
Oil temperature in C or F
195
G0688811
8 Technical Reference
8.6 Drawings
The nomogram is based on the properties of fresh water. The presence of salt water in the oil may demand a gravity disc with a larger hole than indicated in the nomograms. Example I in nomogram
From the graphs (heavy line), the correct gravity disc has a hole diameter of 64,5 mm.
Example II in nomogram
Reference in graph: _ _ _ _ _ _ _
Oil density Separation temperature Throughput 888 kg/m 3 at 15 C (60 F) 90 C (194 F) 1,8 m3/h
From the graphs (broken line), the correct gravity disc has a hole diameter of 84 mm.
196
8.6 Drawings
8 Technical Reference
8.6.7
Electric motor
Manufacturer
ABB Motors
Manufacturers drawing MK20-92S Standards Size Type Weight Poles Insulation class Bearings Method of cooling Specification IEC 34-1, IEC 72 112 M MBT 112M 31 kg 4 F DE 6206-Z/C3 NDE 6205-Z/C3 IC 41 (IEC 34-6) Totally enclosed three-phase motor for marine service 3)
Type of mounting
Degree of protection
197
G0644511
8 Technical Reference
8.6 Drawings
Article No Output Speed Freq Voltage Current Pow.fac |st / | 1) Therm 2) kW RPM Hz V A cos C
552810-01 552810-02 552810-03 552810-04 552810-05 552810-06 552810-07 552810-08 4 4 4 4 4 4 4,6 4,6 1425 1425 1425 1425 1425 1425 1725 1725 50 50 50 50 50 50 60 60 200 D 220 D 380 D 415 D 440 D 500 D 220 D 440 D 230 D 460 D 575 D 17 16 9 8,2 7,8 6,8 18 9 18 8,6 6,9 0,83 0,83 0,83 0,83 0,83 0,83 0,83 0,83 5,6 5,6 5,6 5,6 5,6 5,6 5,6 5,6
Note
552810-09
4,6
1725
60
0,83
5,6
552810-10
4 4,6
1425 1725
50 60
380 D 440 D
9 9
0,83
5,6 5,6
1)
lst /l=starting current /rated current at direct on line starting. Thermistors tripping temperature if applicable The motors can be designed to fulfill requirements of following Classification Societies: Lloyds Register of shipping (LRS) (Essential Service) Det Norske Veritas (DnV) (Essential Service) Germanischer Lloyd (GL) (Essential Service) Bureau Veritas (BV) (Essential Service) American Bureau of shipping (ABS) (Essential Service) Registro Italiano Navale (RINA) (Essential Service) USSR Register of Shipping (RSU) (Essential Service) Japanese Classification Society (NKK) (Essential Service)
2) 3)
Required classification society must always be specified when ordering. Factory test certificate to be enclosed at the delivery. Rated output (kW) valid for temp-rise max. 90 C.
198
8.6 Drawings
8 Technical Reference
8.6.8
Electric motor
A: 4 holes, diam. 14 mm
Only for applications on shore. Standards Size Poles Method of cooling Specification IEC 34-1, IEC 72 112 M/F215 acc. to IEC72 4 R Totally enclosed three-phase induction motor, fan cooled
Degree of protection
Type of mounting
199
G0684611
8 Technical Reference
8.6 Drawings
Article No
540196-10 540196-11 540196-12 540196-131) 540196-18 540196-19 540196-20 540196-21 540196-22 540196-23 540196-24
Note
1)
200
8.6 Drawings
8 Technical Reference
8.6.9
Machine bottom part (without pump) 540224-10/11 (50/60 Hz) Machine bottom part (with pump) 540224-03/04 (50/60 Hz) Max. speed (bowl) Direction of rotation (bowl) Speed, motor shaft El. current frequency Recommended motor power Max. density of feed Max. density of sediment Max. density of operating liquid Process temperature min./max. 7607 r/min. (50 Hz), 7537 r/min. (60 Hz) 1500 r/min. (50 Hz), 1800 r/min. (60 Hz) 50/60 Hz 4 kW 1100 kg/m3 2362 kg/m 3 1000 kg/m3 0/100 C
201
G0644411
8 Technical Reference
8.6 Drawings
3. Safety label Text on label: DANGER Read the instruction manuals before installation, operation and maintenance. Consider inspection intervals. Failure to strictly follow instructions can lead to fatal injury. If excessive vibration occurs, stop separator and keep bowl filled with liquid during rundown. Out-of-balance vibration will become worse if bowl is not full. Separator must stop rotating before any dismantling work is started.
S0061521
Switch rating, voltage: Max. 500 V current: Max. 3 A For other technical information see chapter 8.3 Interface description on page 175.
G0547221
202
S0063111
S0063211
4. Name plate
8 Technical Reference
8.7
8.7.1
Storage
Specification
Upon arrival to the store, check all components and keep them: 1. Well stored and protected from mechanical damage and theft. 2. Dry and protected from rain and humidity. 3. Organized in the store in such a way that the goods will be easily accessible when installation is about to take place.
203
8 Technical Reference
A separator can be delivered with different types of protection: Fixed on a pallet. The separator must be stored in a dry storage room, protected from rain and humidity. It must be well protected from mechanical damage and theft.
Fixed on a pallet
In a wooden box which is not water tight. The separator must be stored in a dry storage room, protected from rain and humidity.
In a special water-resistant box for outdoor storage. The separator and its parts have been treated with an anti-corrosion agent. Once the box has been opened, store dry and protected from rain and humidity. The packaging for outdoor storage is only to special order.
G0057311
204
G0057211
G0057111
8 Technical Reference
Transport
Specification
During transport of the separator, the frame hood and bowl must always be removed from the machine. When lifting a separator it must always be hung securely. See details in chapter 5.5 Lifting instructions on page 85.
WARNING
Crush hazards Use correct lifting tools and follow lifting instructions.
During erection, all inlets and outlets to separators and accessories must be covered to be protected from dirt and dust.
8.7.2
Planning of installation
Introduction The space required for one or more separators can be calculated by consulting the drawings in the chapters 8.6.1 Basic size drawing, separator with built-on pump on page 188, 8.6.5 Foundations on page 193 and instructions for ancillary equipment, electrical and electronic equipment and cables.
Check the drawings when planning the installation
Important measurements Important measurements are the minimum lifting height for lifting tackle, shortest distance between driving motor and wall, free passage for dismantling and assembly, maintenance and operation. Small size separators are easier to operate and maintain if mounted on an elevated foundation.
Small size separators are easier to operate and maintain if mounted on an elevated foundation
205
G0020911
G0020611
8 Technical Reference
Plan your installation with sufficient room for the controls and operation so that instruments are easily visible. Valves and controls must be within convenient reach. Pay attention to space requirements for maintenance work, work benches, dismantled machine parts or for a service trolley.
Space for separator The separator shall be placed in such a way that suitable space for maintenance and repair is obtained.
Specification
G0020721
See chapter 8.6.5 Foundations on page 193 for the service space required with the separator installed.
Suitable space must be obtained for the maintenance work
Recommendation
The spanner for the large lock ring should have sufficient space to make a complete turn without touching any of the ancillary equipment surrounding the separator.
Specification
A minimum height is required to lift the bowl, bowl parts and the bowl spindle, see chapter 8.6.5 Foundations on page 193.
Recommendation
When two or more separators are installed, the lifting height may have to be increased to enable parts from one separator to be lifted and moved over an adjoining assembled separator.
206
8 Technical Reference
Specification
The plug for gearbox oil draining must not be blocked by floor plate arrangement, etc.
Recommendation
It should be possible to place a portable collecting tray under the gearbox drain plug for changing oil.
Place the separator in such a way that makes the oil change easy
207
G0641411
8 Technical Reference
8.7.3 NOTE
Foundations
When lifting a separator it must always be hung securely. See chapter 5.5 Lifting instructions on page 85.
Specification
The separator can either be installed at floor level or on a platform, see chapter 8.6.5 Foundations on page 193. When a separator is installed on a ship, the separator should be installed in such a way that the centre line of the electric motor is parallel with the centre line of the ship. The electric motor should preferably be pointing aft. The separator must be installed on a strong and rigid foundation to reduce the influence of vibrations from adjacent machinery. The foundation should be provided with a cofferdam. Fit the separator frame on the foundation as follows: Place the separator frame without cushions in position. Check that the bolts do not press against the edges of the holes, otherwise the elasticity of the mounting of the separator frame will be impeded.
G0258911
F = Forward A = Aft
Fit height adjusting washers required. Check that the separator frame is horizontal and that all feet rest on the foundation. Lift the separator frame, fit the vibration dampers (1, 2), lower and check that the bolts do not press against the edges of the holes. Tighten nut (3) with 20 Nm. Hold firmly and secure with the lock nut (4). Repeat for the other frame feet.
208
G0547811
Product: Date:
Book No.:
1270366-02 V2
Yes Is it easy to find what you are looking for by using the table of contents? Are the chapter and section headings clear and adequate? Is the information presented in the correct order for your purposes? Does the information in the manual cover your needs? Is it easy to understand the instructions in the manual? Is the terminology sufficiently explained? Are the illustrations easy to understand? Your comments:
No
209
210
Order Form
If you wish to order extra copies of this manual, please copy this page and give it to your local Alfa Laval representative, who will advise you of current prices. Your local Alfa Laval representative will also be able to help you with information regarding any other manuals.
Company: City:
Product: Quantity:
1270366-02 V2
Comments:
211
212
Index
A
Application Assembly Bowl body and operating mechanism Bowl hood and disc stack General directions Horizontal driving device Inlet/outlet, frame hood Tools (special) Vertical driving device 18 118 109 100 144 104 101 133
B
Bearings Maintenance directions Replacement on bowl spindle Replacement on horizontal driving device Bowl 109, Assembly 106, Dismantling Bowl discs Cleaning Disc stack pressure Bowl spindle Assembly Brake Design and function Renewing of friction pad 94 126 138 56 118 115 88 61 133 18 73
C
Centrifugal separation Check points Ball and roller bearings Before shutdowns Bowl hood seal ring Bowl spindle - radial wobble Bowl spindle cone and bowl body nave Brake Buffer springs and ball bearing housing Cleaning agents Cleaning of bowl discs Corrosion Coupling friction pads Cracks Disc stack pressure Erosion External cleaning Flexible plate in coupling 16 94 97 56 72 72 73 74 86 88 57 75 60 76 62 86 77
Guide surfaces Inlet pipe and oil paring disc Level ring Lifting instructions Lock ring - priming Lock ring - wear and damage Oil change procedure Oil paring disc - height position Operating mechanism Operating paring disc - height position Operating slide Repair of galling Sliding bowl bottom Springs for operating mechanism Vibration analysis Worm wheel and worm - wear of teeth Worm wheel shaft - radial wobble Clarifier Definition Clarifier bowl Characteristic parts Cleaning Cleaning agents Cleaning of bowl discs External cleaning Connection list Connections Description Dimensions Corrosion Coupling Function Renewing of friction pads Cover interlocking switch Design and function Cover interlocking switch (option) Drawing Cracks
D
Daily checks Density of feed Disc Disc stack pressure Dismantling Bowl body and operating mechanism Bowl hood and disc stack General directions Horizontal driving device 49 170 61 61 115 106 100 140
213
Operating water device Tools Vertical driving device Drawings Basic size drawing Cover interlocking switch (option) Dimensions of connections Electric motor Foundations Machine plates and safety labels
122 101 128 188 201 189, 191 196, 198 193 200
I
Installation Interface Definition Description Interface description Intermediate service 204 33 31 175 45, 50
L
Lifting instructions Lock ring Priming Wear and damage Lubricants Lubrication chart, general, oil groups Oil change interval Oil change procedure Oil level Recommended greases Recommended lubricating oils Recommended oil brands Recommended pastes and bonded coatings Volume of lubricating oil 85 80 67 180 182 92 92 187 182 183 186 171
E
Electric motor Drawings. See Motor Emergency stop. See Safety stop Erosion Exploded views Bowl body and operating mechanism Bowl hood and disc stack Horizontal driving device Inlet/outlet, frame hood Operating water device Vertical driving device 196, 198 62 114 105 138 102 121 126
F
Foundations Drawing Installation Frame feet Installation Replacement Friction coupling Function 193 207 207 55 20
M
Machine plates and safety labels Main parts Maintenance intervals Maintenance logs 3-year Service (3S) Daily checks Intermediate Service (IS) Major Service (MS) Oil change Maintenance, general information Ball and roller bearings Before shutdowns Cleaning Lifting instructions Maintenance intervals Maintenance procedure Oil change procedure Service kits Vibration analysis Major service Materials Metal surfaces Cleaning and cleaning agents Corrosion Cracks Erosion 200 19 46 55 49 50 52 49 94 97 86 85 45 47 92 48 93 45, 52 170 86 57 60 62
G
Gear Number of teeth Wear of teeth Gravity Guide surfaces Intermediate Service Major Service Repair of galling 170 89 194 64 79 65
H
Horizontal driving device Assembly Dismantling 144 140
214
N
Noise 170
O
Oil. See Lubrication Operation 36
P
Power consumption Power transmission Process capacity Pump Axial play Function Purification Definition Purifier bowl Gravity disc 170 20 170 154 22 33 27
Running Safety stop Sensors and indicators Sludge discharge cycle Start Storage and transportation Technical data Service instructions. See Check points Service kits Shutdown Speed Speed too high Start Stopping procedure Storage
T
Technical data Throughput Capacity Definition Transport Trouble tracing - mechanical functions Noise Retardation time too long Separator vibrates Smell Speed too low Starting power too high Starting power too low Starting time too long Water in worm gear housing Trouble tracing - separating functions Bowl fails to open Bowl opens accidentally Unsatisfactory separation result 170 170 33 202 159 162 158 159 159 160, 161 160 161 162 164 164 166, 168
R
Ready for start Revolution counter Design and function Number of revolutions 38 21 170
S
Safety Instructions 9 Separation 16 Basic principles 29 Clarification 24 Process main parts 27 Purification Separating function trouble tracing 163, 166, 168 17 Separation temperatures Separator 188, 190 Basic size drawing 20 Brake 172 Connection list 193 Foundations 204 Installation planning 175 Interface description 85 Lifting instructions 24 Main parts 20 Mechanical power transmission 41 Normal stop 19 Overview 38 Ready for start
V
Vertical driving device Assembly Vibration During start Trouble tracing Vibration analysis Vibration switch (option) Description and signal processing 133 39 158 93 176
215
W
Warning signs Water Water quality specifications Weight Worm gear Function and description Number of teeth Wear of teeth 13 179 170 20 170 89
216