Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
198 views

RF Basics

RF stands for radio frequency and refers to electromagnetic signals. The sine wave is the basic signal that can be generated and transmitted using RF equipment. Frequency is measured in Hertz and refers to the number of cycles per second, while amplitude is measured in Volts and relates to signal strength. Decibels are used to express power ratios and gains/losses in RF systems as adding or subtracting decibels is simpler than multiplying/dividing power values. Power budget calculations allow determining the power at different points in an RF chain by adding/subtracting gains and losses expressed in decibels.

Uploaded by

Hatem MOKHTARI
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
198 views

RF Basics

RF stands for radio frequency and refers to electromagnetic signals. The sine wave is the basic signal that can be generated and transmitted using RF equipment. Frequency is measured in Hertz and refers to the number of cycles per second, while amplitude is measured in Volts and relates to signal strength. Decibels are used to express power ratios and gains/losses in RF systems as adding or subtracting decibels is simpler than multiplying/dividing power values. Power budget calculations allow determining the power at different points in an RF chain by adding/subtracting gains and losses expressed in decibels.

Uploaded by

Hatem MOKHTARI
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

RF Basics

Marco Zennaro and Carlo Fonda - ICTP-ARPL

RF Basics
RF stands for Radio Frequency, but it often used in the
sense of anything related with EM signals.
The sine wave is the basic example of a signal that can
be generated, transmitted and received with RF
equipment.
It may be characterized by:
Frequency
Amplitude

RF Basics
Frequency: the number of times a signal goes through
a complete up and down cycle in one second of
time. It is measured in Hertz.
Amplitude: the difference between the maximum and
the minimum value during one cycle. It is measured in
Volts, and it is related with the strength, or power, of
the signal.

RF Basics

Frequency: the number of times a signal goes through


a complete up and down cycle in one second of
time. 1

Hz

Amplitude: the difference between the maximum and


the minimum value during one cycle. 2 V

RF Basics
We use the Scientific Notation that uses the power of
ten to multiply the values.

milli (m)

-3
10

1 mV

micro()

-6
10

1 V

kilo(k)

3
10

1 kHz

mega(M)

6
10

1 MHz

giga(G)

9
10

1 GHz

RF Basics
Frequency Band: the standard name of a specific
range of frequencies.
HF: High Frequency, 3 MHz to 30 MHz
VHF: Very High Frequency, 30 MHz to 300 MHz
UHF: Ultra High Frequency, 300 MHz to 3 GHz
SHF: Super High Frequency, 3 GHz to 30 GHz
EHF: Extra High Frequency, 30 GHz to 300 GHz

RF Basics
Bandwidth: width of the range of frequencies that a
signal occupies on a given transmission medium. It is
the difference between the highest-frequency signal
component and the lowest-frequency signal
component.
Voice transmission: 3 kHz
FM radio broadcast: 200 kHz
Analog TV broadcast: 6 MHz

RF Basics
Wavelength: the distance a radio wave will travel
during one cycle.

=c/f
is the wavelength, in meters
c is the speed of light, 299793 m/s
f is the frequency, in Hz

RF Basics
Frequency

Wavelength

900 MHz

0.33 m

2.4 GHz

0.125 m

5.0 GHZ

0.06 m

RF Basics
Power: in the RF world, the power is commonly used
to quantify a signal, instead of the amplitude.
Power is expressed in Watts.
For low-frequency signals, the power is given by

P=EI
For high-frequency signals with no reactance, by the
root-mean-square values.
For high-frequency signals with reactance, RF power is
a vector, 2-D, quantity.

RF Basics
Decibel: the decibel (abbreviated as dB) is a
logarithmic expression of the ratio between the
power, voltage, or current of two signals.
Signal one, with a power of P1 Watts
Signal two, with a power of P2 Watts

P =10log (P /P )
dB

10

RF Basics
If the load impedance is constant, decibels can be
calculated in terms of effective voltage.
Signal one, with an RMS voltage of V1 across a load
Signal two, with an RMS voltage of V2 across a load

V =20log (V /V )
dB

10

RF Basics
When the decibel figure is positive, the second signal
is stronger than the first one, and the power ratio is
called gain.
When the decibel figure is negative, the second signal
is weaker than the first one, and the power ratio is
called loss.
In amplifiers the gain, also called the amplification
factor, in often expressed in decibels.

RF Basics
+ 3 dB

two times
bigger

+10 dB

ten times
bigger

-3 dB

one half

-10 dB

one tenth

RF Basics
To express power using decibels we need a specific
power to be assumed as a reference.
In the RF world the common standard is to refer
powers to 1 mW (0.001 Watts).
Such power ratio, expressed in decibels, is called
dBm.

P =10log (P /1mW)
dBm

10

watts

100 W
1 mW
10 mW
100 mW
1W
10 W
100 W

=
=
=
=
=
=
=

-10 dBm
0 dBm
10 dBm
20 dBm
30 dBm
40 dBm
50 dBm

RF Basics

The advantage of using decibels instead of Watts to


express ofthe
power
ofinstead
a signal
along
an RFthe
chain
The advantage
using
decibels
of Watts
to express
poweris that
instead
multiplying
to take
of a signal
along of
an dividing
RF chain (aorchain
composed powers
by RF devices
like care
transmitters,
receivers, cables, and
amplifiers,
attenuators, we
measurement
of amplifications
attenuations,
just add or
instruments,
loads, etc.)
that instead
of dividing
multiplying powers
to
subtract
the isgains
and the
lossesorexpressed
in decibels.
take care of amplifications and attenuations, we just add or subtract the
gains and the losses expressed in decibels. An example follows:
Transmitter

Amplifier
Cable 1

Receiver
Cable 2

Using amplification and attenuation factors and expressing the powers in


Watts, we obtain the value of the power at the receivers input in this way:
PReceiver

1
1
= PTransmitter "
" Amplification "
Attenuation Cable1
AttenuationCable2

RF Basics
Using amplification and attenuation factors and
expressing the powers in Watts, we obtain the value of
the power at the receivers input in this way:
Prec=Ptransm x (1/Attcable1) x Amp x(1/Attcable2)
If we use dB to express the gains and the losses and
dBm to express the powers, the calculation becomes a
simple addition:
Prec=Ptransm + Losscable1 + Gainamp + Losscable2
This procedure is called Power Budget Calculation

RF Basics
Signals are characterized by frequency.
We are interested in signals at 2.4 GHz.
At 2.4 GHz, the wavelength is 12.5 cm.
We will use dB, so we can use Power Budget
Calculation.

You might also like