This sample chapter is for review purposes only. Copyright The Goodheart-Willcox Co., Inc. All rights reserved.

58

Gas Metal Arc Welding Handbook

CHAPTER

Weld Joints and Weld Types

Joint Preparation Weld joints may be initially prepared in a number of ways. These include: Shearing. Casting. Forging. Machining. Stamping. Filing. Routing. Oxyacetylene cutting (thermal cutting process). Plasma arc cutting (thermal cutting process). Grinding. Final preparation of the joint prior to welding will be covered in the chapters that detail the welding of specific materials.

Butt

Bevel-groove

V-groove

Fillet

Bevelgroove

J-groove

J-groove

U-groove

Plug

Slot

Spot

Objectives
After studying this chapter, you will be able to: Identify different types of welds used with various joints. Read and draw common welding symbols. Discuss advantages and disadvantages of different weld joints. List factors involved with joint design.

Figure 6-4. Types of welds that may be made with a basic lap joint.

Flare-V

Flare-bevel

Joint Types
The American Welding Society defines a joint as the manner in which materials fit together. As shown in Figure 6-1, there are five basic types of weld joints: Butt joint. T-joint. Lap joint. Corner joint. Edge joint.

Figure 6-2. Types of welds that may be made with a basic butt joint.

Weld Types
There are various types of welds that can be made in each of the basic joints. They include: Butt joint, Figure 6-2. Square-groove butt weld. Bevel-groove butt weld. V-groove butt weld. J-groove butt weld. U-groove butt weld. Flare-V-groove butt weld. Flare-bevel-groove butt weld. T-joint, Figure 6-3. Fillet weld. Plug weld. Slot weld. Bevel-groove weld. J-groove weld. Flare-bevel-groove weld. Melt-through weld.

Bevel-groove

J-groove

Fillet

Butt

T Lap Corner

Flare-bevel

Lap joint, Figure 6-4. Fillet weld. Plug weld. Slot weld. Spot weld. Bevel-groove weld. J-groove weld. Flare-bevel-groove weld. Corner joint, Figure 6-5. Fillet weld. Spot weld. Square-groove weld or butt weld. V-groove weld. Bevel-groove weld. U-groove weld. J-groove weld. Flare-V-groove weld. Edge weld. Corner-flange weld. Edge joint, Figure 6-6. Square-groove weld or butt weld. Bevel-groove weld. V-groove weld. J-groove weld. U-groove weld. Edge-flange weld. Corner-flange weld. Double Welds In some cases, a weld cannot be made from only one side of the joint. When a weld must be made from both sides, it is known as a double weld. Figure 6-7 shows common applications of double welds in basic joint designs.

Edge

Figure 6-1. The five basic types of joints used in welding.

Slot

Plug

Figure 6-3. Types of welds that may be made with a basic T-joint.

57

Chapter 6

Weld Joints and Weld Types

59

60

Gas Metal Arc Welding Handbook

Butt

Fillet

J-groove
Butt Bevel V-groove

Figure 6-8. Joggle-type joint. Figure 6-11. Plate butt weld with a fabricated backing bar.

Spot

V-groove

Edge

J-groove

U -groove

Figure 6-9. Tubular butt joint with a built-in backing bar.

Corner flange

Figure 6-12. Controlled weld penetration joint.

Flare-V
Bevel and fillet Fillet Double fillet

Figure 6-5. Types of welds that may be made with a basic corner joint.

Figure 6-7. Applications of double welds.

Butt

Bevel-groove

J-groove

V-groove

U-groove

Edge flange

Corner flange

Figure 6-6. Types of welds that may be made with a basic edge joint.

Weldment Configurations The basic joint often is changed to assist in a components assembly. A weld joint might be modified to gain access to the weld joint or to change a welds metallurgical properties. Some common weldment configuration designs are described here. Joggle-type joints are used in cylinder and head assemblies where backing bars or tooling cannot be used. See Figure 6-8. Another application of joggle joints is in the repair of unibody automobiles where skin panels are placed together and welded. A built-in backing bar is used when enough material is available for machining the required backing or when tooling cannot be inserted (as in some tubular applications). An example in which tubing is being joined to heavy wall tube is shown in Figure 6-9. Pipe joints often use special backing rings or are machined to fit specially designed mated parts. Types of backing rings are shown in Figure 6-10. Figure 6-11 shows a fabricated backing bar. These bars must fit tightly or problems will be encountered in heat flow and penetration. Weld joints specially designed for controlled penetration are used where excessive weld penetration would cause a problem with assembly or liquid flow. This type of joint is shown in Figure 6-12.

Figure 6-13. Buttered weld joint face.

Figure 6-10. Various types of backing rings for pipe joints.

Figure 6-14. Overlaid welds, called surfacing or cladding, protect the base metal from wear or contamination.

Welding Terms and Symbols

A series of bead welds overlaid on the face of a joint is called buttering, Figure 6-13. Buttered welds are often used to join dissimilar metals. A series of overlaid welds on the surface of a part to protect the base material is called surfacing or cladding. Refer to Figure 6-14. Communication from the weld designer to the welder is essential to proper completion of most weldments. Some of the common terms used to describe parts of the weld joint are found in Figure 6-15. Other

Chapter 6

Weld Joints and Weld Types

61

62

Gas Metal Arc Welding Handbook

Groove Square Scarf V Bevel U J Flare-V Flarebevel

terms used to describe welds are given in Figure 6-16. The AWS welding symbol shown in Figure 6-17 was developed as a standard by the American Welding Society. This symbol is used on drawings to indicate the type of joint, placement, and the type of weld to be made.

The symbol may also include other information, such as finish and contour of the completed weld. It is important to study and understand each part of the welding symbol. Figure 6-18 is a table showing basic weld symbols that are used with the AWS welding
Weld crown Weld toe

Bevel angle

Groove angle

Crown height

Root penetration Root face thickness Root opening Weld toe Weld crown Riser Weld throat Leg length Root penetration

Fillet

Plug or slot

Stud

Spot or projection

Seam

Back or backing

Surfacing

Edge

Leg length

Figure 6-18. Basic weld symbols. (Printed with permission of the American Welding Society)

Figure 6-15. Weld joint terms.

Figure 6-16. Weld and weld area terms.

Finish symbol Contour symbol Groove weld size Depth of bevel; size or strength for certain welds

Groove angle; included angle of countersink for plug welds

F A R S(E)
ARROW SIDE

Root opening; depth of filling for plug and slot welds Length of weld Pitch (center-to-center spacing) of welds OTHER SIDE

symbol to direct the welder in producing the proper weld joint. The arrow of the welding symbol indicates the point at which the weld is to be made. The line connecting the arrow to the reference line is always at an angle. Whenever the basic weld symbol is placed below the reference line, as shown in Figure 6-19, the weld is

made on the side where the arrow points (referred to as the arrow side). Whenever the basic symbol is placed above the reference line, the weld is to be made on the other side of the joint, as shown in Figure 6-20. By placing dimensions on the symbol and drawings, the exact size of the weld may be indicated. Study the

Specification, process, or other reference

Tail (may be omitted when reference is not used)

BOTH

{ {

} L-P }
Reference line

SIDES

Field weld symbol Weld-allaround symbol

Fillet weld symbol Fillet weld symbol

(N)

Weld symbol

Number of spot, seam, stud, plug, slot, or projection welds

Arrow connecting reference line to arrow side member of joint or arrow side of joint

Arrow side

Other side

Elements in this area remain as shown when tail and arrow are reversed

Desired weld

Desired weld

Weld symbols shall be contained within the length of the reference line

Figure 6-17. The AWS welding symbol conveys specific and complete information to the welder. (Printed with permission of the American Welding Society)

Figure 6-19. Fillet weld symbol shown on the bottom side of the reference line indicates that the weld is located where the arrow points.

Figure 6-20. Fillet weld symbol shown on the upper side of the reference line indicates that the weld is located on the opposite side of the joint.

Chapter 6

Weld Joints and Weld Types

63

64

Gas Metal Arc Welding Handbook

examples of typical weld symbols and weldments shown in Figure 6-21. The complete weld symbol gives the welder instructions on how to prepare the base metal, the welding process to use, and the finish for the completed weld. Through careful use of these symbols, the weld designer can convey all the information needed to complete a weldment. Classes are offered that provide advanced study in the area of print reading for welders. By taking such classes, the welder can improve his or her ability to read and interpret welding drawings. Studying texts on print reading is another method of gaining ability to read prints.

Overhead 4G

U-groove weld symbol

Desired weld
Overhead 4F

Fixed 6G

V-groove weld symbol

Desired weld
Vertical 3G Vertical fixed 5G

Weld Positions
For a welder, it is important to be able to weld in different positions. The American Welding Society has defined the positions of welding to include: Flat. Horizontal. Vertical. Overhead. Figure 6-22 demonstrates the four positions for fillet welds, grooved butt welds, and pipe welds. While practicing welding in these positions, you should note how gravity affects the molten weld pools. In addition to this, heat distribution also varies with each position. These factors make the skills needed for each position distinct. Practice is required to produce good welds in all positions.

Two-sided fillet weld symbol

Desired weld

Vertical 3F

Horizontal 2G

Design Considerations
Design of the weld type and weld joint to be used is of prime importance if the weldment is to do the intended job. The weld should be made at reasonable cost. Several factors concerning the weld design must be considered: Material type and condition (annealed, hardened, tempered). Service conditions (pressure, chemical, vibration, shock, wear). Physical and mechanical properties of the completed weld and heat-affected zone. Preparation and welding cost. Assembly configuration and weld access. Equipment and tooling. Butt Joints and Welds Butt joints are used where high strength is required. They are reliable and can withstand stress better than any other type of weld joint. To achieve full stress value, the weld must have 100 percent penetration through the joint. This can be done by welding completely through from one side. The alternative is working from both sides, with the welds joining in the center.

Fillet weld-allaround symbol

Desired weld
Horizontal 2G Horizontal 2F

Bevel-groove weld symbol

Desired weld

Flat 1G

Rotated flat rolled 1G

Flat 1F Fillet Welds Grooved Butt Welds Pipe Welds

Figure 6-22. American Welding Society definitions of welding positions.

Entire surface built up weld symbol Desired weld

Figure 6-21. Typical weld symbols and weld applications.

Thinner-gauge metals are more difficult to fit up for welding. Thin metals also require more costly tooling to maintain the proper joint configuration. Tack welding may be used as a method of holding the components during assembly. However, tack welds present many problems:

They conflict with penetration of the final weld into the weld joint. They add to the crown dimension (height). They often crack during welding due to the heat and expansion of the joint. Expansion of the base metal during welding often will cause a condition known as mismatch, Figure 6-23. When mismatch occurs, the weld generally will not penetrate completely through the joint. Many specifications limit highly stressed butt joints to a 10 percent maximum mismatch of the joint thickness.

Whenever possible, butt joints should mate at the bottom, Figure 6-24. Joints of unequal thickness should be tapered in the weld area to prevent incomplete or inadequate fusion. This is shown in Figure 6-25. When this cannot be done, the heavier piece may be tapered on the upper part of the joint as well. Weld shrinkage. Butt welds always shrink across the joint (transversely) during welding. For this reason, a shrinkage allowance must be made if the after welding overall dimensions have a small tolerance. Butt welds in pipe, tubing, and cylinders also shrink on the diameter of

Chapter 6

Weld Joints and Weld Types

65

66

Gas Metal Arc Welding Handbook

Correct

Figure 6-23. Welds made on mismatched joints often will fail below the rated load when placed in stress conditions.
Single fillet Open to corrosion

Figure 6-27. Weld joint shrinkage can be determined in four steps. 1. Tack weld the test joint together. 2. Scribe parallel lines, as shown, on approximately 2 centers. Record this dimension. 3. Weld joint with test weld procedure. 4. Measure linear distance and compare with original dimension. Figure 6-24. Mating the joint at the bottom equalizes the load during stress when the weld is made from the top and penetrates completely through the joint.

Correct Section A Correct design Section B Incorrect design

Figure 6-25. Joints of unequal thickness absorb different amounts of heat and expand at different ratios. Equalize the heat flow by tapering the heavier material to the thickness of the thinner material.

T-Joints and Welds Various T-joint designs are used to join parts at an angle to each other. Depending on the intended use of the weldment, the joint may be made with a single fillet, double fillet, or a groove and fillet weld combination. Figure 6-28 shows these designs. Fillet welds are made to specific sizes that are determined by the allowable design load. They are measured as shown in Figure 6-29. Where design loads are not known, a rule of thumb may be used for determining the fillet size. In these cases, the fillet weld leg lengths must equal the thickness of the thinner material. The main problem in making fillet welds is lack of penetration at the joint intersection. To prevent this condition, always make stringer beads at the intersection. Weave beads do not provide the desired penetration on fillet welds. Lap Joints and Welds Lap joints may be either single fillet, double fillet, plug slot, or spot-welded. They require very little joint preparation. They are generally used in static load applications or in the repair of unibody automobiles. Where corrosive liquids are involved, both edges of the joint must be welded. See Figure 6-30. One of the major problems with lap joint design is shown in Figure 6-31. Where the component parts are not in close contact, a bridging fillet weld must then be made. This leads to incomplete fusion at the root of the weld and oversize fillet weld dimensions. When using this type of design in sheet or plate material, clamps or tooling must be used to maintain adequate contact of the material at the weld joint. An interference fit eliminates this problem in assembly of cylindrical parts, Figure 6-32. The inside diameter of the outer part is made several thousandths of an inch smaller than the outside diameter of the inner

Double fillet

Figure 6-30. Corrosive liquids must not be allowed to enter the penetration side of the weld joint. In Section A, the back of the weld is closed to corrosion. In Section B, the back of the weld is open to corrosion.

Bevel and fillet

Figure 6-31. Lap joint problem areas that result from improper fit-up.

Figure 6-28. Various types of T-joints and welds.

Outer part

I.D.

Figure 6-26 Butt welds shrink during welding in both transverse and circumferential directions.

Size of required weld

Inner part

the material. This shrinkage is shown in Figure 6-26. In areas where these dimensions must be maintained, a shrinkage test must be done to establish the amount of shrinkage. Figure 6-27 shows how such a test is made. Heavier materials will shrink more than thinner materials. Double-groove welds will shrink less than single-groove welds. This is because less welding is involved and less filler material is used.

O.D. Leg length

Figure 6-29. Fillet weld leg lengths from the root of the joint should be equal. Unequal leg length, unless otherwise specified, will not carry the designed load and may fail under stress.

Figure 6-32. The diameters of the parts to be assembled with an interference fit may be found by using a pi tape around the inner and outer cylinder components. The tape measures in thousandths of an inch and full inches.

Chapter 6

Weld Joints and Weld Types

67

68

Gas Metal Arc Welding Handbook

part. Before assembly, the outer part is heated until it expands enough to slide over the inner part. As the part cools, it shrinks and locks the two pieces together. Corner Joints and Welds Corner joints are similar to T-joints, since they consist of sheets or plates mating at an angle to one another. They are usually used in conjunction with groove welds and fillet welds. Some of the many different corner weld designs are shown in Figure 6-33. When using thinner gauges of metal, it may be difficult to assemble component parts without proper tooling. Tack welding and welding often will cause distortion and buckling of thinner materials. For the most part, use of corner joints should be limited to heavier materials in structural assemblies. Edge Joints and Welds Edge welds are used where the edges of two sheets or plates are adjacent and are in approximately parallel planes at the point of welding. Figure 6-34 shows several types of edge weld designs. These designs are common only in structural use. Since the weld does not penetrate completely through the joint thickness, it should not be used in stress or pressure applications.

Wall thickness

Reinforcement Heat affected zone within this area

Figure 6-37. Temperature crayons and pellets may be used to determine preheating temperatures prior to welding. Figure 6-35. The joint thickness and the filler material tensile strength is equivalent to the strength of the base material in this design.
Hold-down and chill bars

Figure 6-34. Common edge weld joint designs that may be used in fabrication.

Edge to edge

Flush corner

Half overlap

Figure 6-33. Common corner weld joint designs that may be used in fabrication.

Special Designs and Procedures Special designs are often used in the fabrication of a weldment where: Welds cannot be thermally treated after welding because of configuration or size. Material is added to the joint thickness, as shown in Figure 6-35, and the weld is made restricting the heat flow into the thinner metal. This type of joint will achieve the full mechanical values of the base material. Joining of dissimilar materials can be done by buttering the face of one material to match the other, as shown in Figure 6-36. Special procedures and tooling may be used to provide a preheating, interpass, and postheating operation to control grain size. Preheating is generally used to slow down the cooling rate of the weld to prevent cracking. Interpass temperature is the Min/Max temperature at which a weld can be made on a multi-pass weld. Individual chapters regarding the welding of various metals will define the requirements for preheating, interpass, and postheating temperatures. These temperatures may be checked by the use of special crayons, paints, or pellets like those in Figure 6-37. Special procedures, tooling, and chill bars may be used to localize and remove welding heat during the welding application. Figure 6-38 shows an application of tooling used to remove heat from the part.

New weld

Backing and chill bar

Original material Buttered weld

Original material Buttered weld

Figure 6-38. Tooling and bars used to remove heat from the weld and resist heat flow into the base material are sometimes called chill bars.

Figure 6-36. Buttering techniques are commonly used to adapt dissimilar metals for welding.

Review Questions
Write your answers on a separate sheet of paper. Do not write in this book. 1. What are the five basic types of joints? 2. Welds made from both sides of the joint are called _____ welds. 3. _____ welds are often used where dissimilar materials are joined. 4. Weld material placed on the surface of a joint for protection of the base material is called _____ or _____. 5. The oxyacetylene and the plasma arc processes are _____ cutting processes. 6. Where high-strength welds are required, a _____ joint weld with 100 percent penetration is used.

7. Unless tack welds are made properly, they often _____ during the welding operation. 8. Fillet welds are always measured by the length of the fillet _____. 9. Where fillet weld dimensions are not specified, the size of the weld should equal the thickness of the _____ material. 10. The condition of a butt joint where neither the top nor the bottom edge of the material is flush is called _____. 11. _____ joints always shrink across the weld joint. 12. The main problem in making fillet welds is _____ _____ _____ into the root of the joint. 13. Edge-type joints without full penetration of the weld should not be used in _____ _____. 14. _____ bars are used during welding to localize and remove heat from the weld area. 15. The American Welding Society defines four positions of welding: _____, _____, _____, and _____.