Alfa Laval Pump Handbook PDF

All you need to know ...
Alfa Laval Pump Handbook
Second edition 2002

The information provided in this handbook is given in good faith, but Alfa Laval is not able to accept any responsibility for the accuracy of its content, or any consequences that may arise from the use of the information supplied or materials described.
Inside view
This pump handbook has been produced to support pump users at all levels, providing an invaluable reference tool. The handbook includes all the necessary information for the correct selection and successful application of the Alfa Laval ranges of Centrifugal, Liquid Ring and Rotary Lobe Pumps. The handbook is divided into fifteen main sections, which are as follows:
1 Introduction 2 Terminology and Theory 3 Pump Selection 4 Pump Description
9 10 11 12
Motors Cleaning Guidelines Compliance with International Standards and Guidelines Installation Guide Troubleshooting Technical Data Glossary of Terms
5 Pump Materials of Construction 13 6 Pump Sealing 14 7 Pump Sizing 15 8 Pump Specification Options
Alfa Laval Pump Handbook 1
Contents
Section 1: Introduction
Introduction of the Pump Handbook. 1.1 What is a Pump? 5 5
Section 5: Pump Materials of Construction

Description of the materials, both metallic and elastomeric, that are used in the construction of Alfa Laval pump ranges. 5.1 5.2 5.3 7 Main Components Steel Surfaces Elastomers
61 61 63 65
Section 2: Terminology and Theory

Explanation of the terminology and theory of pumping applications, including rheology, flow characteristics, pressure and NPSH. 2.1 2.1.1 2.1.2 2.1.3 2.1.4 2.1.5 2.1.6 2.1.7 2.1.8 2.1.9 2.2 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 Product/Fluid Data Rheology Viscosity Density Specific Weight Specific Gravity Temperature Flow Characteristics Vapour Pressure Fluids Containing Solids Performance Data Capacity (Flow Rate) Pressure Cavitation Net Positive Suction Head (NPSH) Pressure Shocks (Water Hammer)
Section 6: Pump Sealing

8 8 8 12 12 13 13 13 17 17 18 18 18 30 31 35 Explanation of pump sealing principles with illustrations of the different sealing arrangements used on Alfa Laval pump ranges. A general seal selection guide is included, together with various operating parameters. 67 6.1 6.2 6.3 Mechanical Seals - General 70 Mechanical Seal Types in Alfa Laval Pump Ranges 80 Other Sealing Options (Rotary Lobe Pumps only) 82
Section 7: Pump Sizing

How to size an Alfa Laval pump from product/fluid and performance data given, supported by relevant calculations and worked examples with a simple step by step approach. 85 7.1 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.3 7.3.1 7.3.2 7.3.3 7.4 7.4.1 7.4.2 7.5 7.5.1 7.5.2 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 7.6.6 7.6.7 7.6.8 7.6.9 7.7 7.8 General Information Required 85 Power 86 Hydraulic Power 86 Required Power 87 Torque 88 Efficiency 88 Centrifugal and Liquid Ring Pumps 92 Flow Curve 92 Flow Control 96 Alternative Pump Installations 100 Worked Examples of Centrifugal Pump Sizing (Metric Units) 102 Example 1 102 Example 2 106 Worked Examples of Centrifugal Pump Sizing (US Units) 109 Example 1 109 Example 2 113 Rotary Lobe Pumps 116 Slip 116 Initial Suction Line Sizing 118 Performance Curve 119 Pumps fitted with Bi-lobe Rotors (Stainless Steel) 124 Pumps fitted with Bi-lobe Rotors (Non Galling Alloy) 125 Pumps fitted with Tri-lobe Rubber Covered Rotors 125 Pumps with Electropolished Surface Finish 126 Guidelines for Solids Handling 127 Guidelines for Pumping Shear Sensitive Media 128 Worked Examples of Rotary Lobe Pump Sizing (Metric Units) 129 Worked Examples of Rotary Lobe Pump Sizing (US Units) 143
Section 3: Pump Selection

Overview of the pump ranges currently available from Alfa Laval and which particular pumps to apply within various application areas. 3.1 3.2 3.3 General Applications Guide Pumps for Sanitary Applications PumpCAS Selection and Configuration Tool
39 40 41 43
Section 4: Pump Description

Description of Alfa Laval pump ranges including design, principle of operation and pump model types. 4.1 4.1.1 4.1.2 4.1.3 4.1.4 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.3 4.3.1 4.3.2 4.3.3 Centrifugal Pumps General Principle of Operation Design Pump Range Liquid Ring Pumps General Principle of Operation Design Pump Range Rotary Lobe Pumps General Principle of Operation Pump Range 45 45 45 46 46 48 52 52 52 53 55 56 56 56 57
Section 8: Pump Specifications Options

Description of the various specification options available for the Alfa Laval pump ranges, such as port connections, heating/cooling jackets, pressure relief valves and other ancillaries. 157 8.1 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.2.7 Centrifugal and Liquid Ring Pumps Port Connections Heating/Cooling Jackets Pump Casing with Drain Increased Impeller Gap Pump Inlet Inducer Rotary Lobe Pumps Rotor Form Clearances Port Connections Rectangular Inlets Heating/Cooling Jackets and Saddles Pump Overload Protection Ancillaries 157 157 158 159 159 159 160 160 162 164 165 166 167 169
12.2 12.2.1 12.2.2 12.3 12.4 12.5 12.5.1
Flow Direction Centrifugal Pumps Rotary Lobe Pumps Baseplates Foundation (Rotary Lobe Pumps only) Coupling Alignment (Rotary Lobe Pumps only) Special Considerations for Liquid Ring Pumps Pipework
201 201 202 203 204 204 204
Section 13: Troubleshooting

Advises possible causes and solutions to most common problems found in pump installation and operation. 205 13.1 13.2 13.2.1 13.2.2 13.2.3 13.2.4 13.2.5 13.2.6 13.2.7 13.3 General Common Problems Loss of Flow Loss of Suction Low Discharge Pressure Excessive Noise or Vibration Excessive Power Rapid Pump Wear Seal Leakage Problem Solving Table 205 206 206 206 207 207 208 208 208 209
Section 9: Motors
Description of electric motors, including information on motor protection, methods of starting, motors for hazardous environments and speed control. 173 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 Output Power Rated Speed Voltage Cooling Insulation and Thermal Rating Protection Methods of Starting Motors for Hazardous Environments Energy Efficient Motors Speed Control Changing Motor Nameplates - Centrifugal and Liquid Ring Pumps only 175 175 176 176 176 177 179 180 182 184 186
Section 14: Technical Data

Summary of the nomenclature and formulas used in this handbook. Various conversion tables and charts are also shown. 213 14.1 14.2 14.3 14.3.1 14.3.2 14.3.3 14.3.4 14.3.5 14.3.6 14.3.7 14.3.8 14.3.9 14.3.10 14.3.11 14.4 14.5 14.6 14.7 14.7.1 14.7.2 14.7.3 14.7.4 14.8 14.9 14.10 14.11 Nomenclature Formulas Conversion Tables Length Volume Volumetric Capacity Mass Capacity Pressure/Head Force Torque Power Density Viscosity Conversion Table Temperature Conversion Table Water Vapour Pressure Table Pressure Drop Curve for 100 m ISO/DIN Tube Velocity (m/s) in ISO and DIN Tubes at various Capacities Equivalent Tube Length Table ISO Tube Metric ISO Tube Feet DIN Tube Metric DIN Tube Feet Moody Diagram Initial Suction Line Sizing Elastomer Compatibility Guide Changing Motor Name Plates 213 214 219 219 219 219 220 220 220 220 221 221 222 224 225 226 227 228 228 230 232 234 236 237 238 243
Section 10: Cleaning Guidelines

Advises cleaning guidelines for use in processes utilising CIP (Clean In Place) systems. Interpretations of cleanliness are given and explanations of the cleaning cycle. 189
Section 11: Compliance with International Standards and Guidelines

Description of the international standards and guidelines applicable to Alfa Laval pump ranges. 193
Section 12: Installation Guide

Advises guidelines relating to pump installation, system design and pipework layout. 12.1 12.1.1 12.1.2 12.1.3 12.1.4 General System Design Pipework Weight Electrical Supply 199 199 199 200 200 200
Section 15: Glossary of Terms

Explains the various terms found in this handbook. 249
...if pumps are the question

Alfa Laval is an acknowledged market leader in pumping technology, supplying Centrifugal and Positive Displacement Pumps world-wide to various key application areas such as food, brewery and pharmaceutical.
Introduction
1. Introduction
This section gives a short introduction of the Pump Handbook.
1.1 What is a Pump?

There are many different definitions of this but at Alfa Laval we believe this is best described as: A machine used for the purpose of transferring quantities of fluids and/or gases, from one place to another. This is illustrated below transferring fluid from tank A to spray nozzles B.
Fig. 1.1a Typical pump installation
Pump types generally fall into two main categories - Rotodynamic and Positive Displacement, of which there are many forms as shown in Fig. 1.1b. The Rotodynamic pump transfers rotating mechanical energy into kinetic energy in the form of fluid velocity and pressure. The Centrifugal and Liquid Ring pumps are types of rotodynamic pump, which utilise centrifugal force to transfer the fluid being pumped. The Rotary Lobe pump is a type of positive displacement pump, which directly displaces the pumped fluid from pump inlet to outlet in discrete volumes.
Introduction
Pumps
Positive Displacement
Rotodynamic
Rotor
Reciprocating
Multi-Stage
Single Stage
Multi-Rotor
Single Rotor
Diaphragm
Plunger
End Suction
Double Entry
Screw Circumferential Piston Gear Internal External
Piston Archimedian Screw Flexible Member Peristaltic Vane
Simplex Multiplex
Process Rubber Lined Submersible General Alfa Laval Centrifugal and Liquid Ring
Rotary Lobe Alfa Laval Rotary Lobe
Progressing Cavity
Fig. 1.1b Pump classifications
6 Alfa Laval Pump Handbook
Terminology and Theory
2. Terminology and Theory

This section explains the terminology and theory of pumping applications, including explanations of rheology, flow characteristics, pressure and NPSH.
In order to select a pump two types of data are required: Product/Fluid data which includes viscosity, density/specific gravity, temperature, flow characteristics, vapour pressure and solids content. Performance data which includes capacity or flow rate, and inlet/discharge pressure/head.
Different fluids have varying characteristics and are usually pumped under different conditions. It is therefore very important to know all relevant product and performance data before selecting a pump.
2.1 Product/Fluid Data

2.1.1 Rheology
The science of fluid flow is termed Rheology and one of its most important aspects is viscosity which is defined below.
2.1.2 Viscosity
The viscosity of a fluid can be regarded as a measure of how resistive the fluid is to flow, it is comparable to the friction of solid bodies and causes a retarding force. This retarding force transforms the kinetic energy of the fluid into thermal energy. The ease with which a fluid pours is an indication of its viscosity. For example, cold oil has a high viscosity and pours very slowly, whereas water has a relatively low viscosity and pours quite readily. High viscosity fluids require greater shearing forces than low viscosity fluids at a given shear rate. It follows therefore that viscosity affects the magnitude of energy loss in a flowing fluid. Two basic viscosity parameters are commonly used, absolute (or dynamic) viscosity and kinematic viscosity. Absolute (or Dynamic) Viscosity This is a measure of how resistive the flow of a fluid is between two layers of fluid in motion. A value can be obtained directly from a rotational viscometer which measures the force needed to rotate a spindle in the fluid. The SI unit of absolute viscosity is (mPa.s) in the so-called MKS (metre, kilogram, second) system, while in the cgs (centimetres, grams, seconds) system this is expressed as 1 centipoise (cP) where 1 mPa.s = 1 cP. Water at 1 atmosphere and 20C (68oF) has the value of 1 mPa.s or 1 cP. Absolute viscosity is usually designated by the symbol . Kinematic Viscosity This is a measure of how resistive the flow of a fluid is under the influence of gravity. Kinematic viscometers usually use the force of gravity to cause the fluid to flow through a calibrated orifice, while timing its flow. The SI unit of kinematic viscosity is (mm2/s) in the so-called MKS (metre, kilogram, second) system, while in the cgs (centimetres, grams, seconds) system this is expressed as 1 centistoke (cSt), where 1 mm2/s = 1 cSt. Water at 1 atmosphere and 20C (68oF) has the value of 1 mm2/s = 1 cSt. Kinematic viscosity is usually designated by the symbol .
Relationship Between Absolute and Kinematic Viscosity Absolute and Kinematic viscosity are related by:
where is the fluid density (see 2.1.3).
In the cgs system this translates to: Kinematic Viscosity (cSt) or Absolute Viscosity (cP) = Kinematic Viscosity (cSt) x SG A viscosity conversion table is included in 14.3.10. Viscosity Variation with Temperature Temperature can have a significant effect on viscosity and a viscosity figure given for pump selection purposes without fluid temperature is often meaningless - viscosity should always be quoted at the pumping temperature. Generally viscosity falls with increasing temperature and more significantly, it increases with falling temperature. In a pumping system it can be advantageous to increase the temperature of a highly viscous fluid to ease flow. = Absolute Viscosity (cP) Specific Gravity
Viscosity
Temperature
Fig. 2.1.2a Viscosity variation with temperature
Viscosity
Newtonian Fluids In some fluids the viscosity is constant regardless of the shear forces applied to the layers of fluid. These fluids are named Newtonian fluids. At a constant temperature the viscosity is constant with change in shear rate or agitation. Typical fluids are: Water Beer Hydrocarbons Milk Mineral Oils Resins Syrups
Shear rate
Fig. 2.1.2b Newtonian Fluids
It is not always obvious which type of viscous behaviour a fluid will exhibit and consideration must be given to the shear rate that will exist in the pump under pumping conditions. It is not unusual to find the effective viscosity as little as 1% of the value measured by standard instruments.
Non-Newtonian Fluids Most empirical and test data for pumps and piping systems has been developed using Newtonian fluids across a wide range of viscosities. However, there are many fluids which do not follow this linear law, these fluids are named Non-Newtonian fluids. When working with Non-Newtonian fluids we use Effective Viscosity to represent the viscous characteristics of the fluid as though it was newtonian at that given set of conditions (shear rate, temperature). This effective viscosity is then used in calculations, charts, graphs and handbook information. ?
Viscosity
Viscosity
? ?
Shear rate
Normal Viscometer Reading
Typical Shear Rate in Pumping System
Shear Rate
Fig. 2.1.2c Viscosity against shear rate
Fig. 2.1.2d Viscosity against shear rate
Types of Non-Newtonian Fluids There are a number of different type of non-newtonian fluids each with different characteristics. Effective viscosity at set conditions will be different depending on the fluid being pumped. This can be better understood by looking at the behaviour of viscous fluids with changes in shear rate as follows. Pseudoplastic Fluids Viscosity decreases as shear rate increases, but initial viscosity may be so high as to prevent start of flow in a normal pumping system.
Viscosity
Typical fluids are: Blood Emulsions Gums Lotions Soap Toothpaste Yeast
Shear rate
Fig. 2.1.2e Pseudoplastic Fluids
Dilatant Fluids Viscosity increases as shear rate increases.

Viscosity
Typical fluids are: Clay Slurries Paper Coatings
Shear rate
Fig. 2.1.2f Dilatant Fluids
Viscosity
Thixotropic Fluids Viscosity decreases with time under shear conditions. After shear ceases the viscosity will return to its original value - the time for recovery will vary with different fluids. Typical fluids are: Cosmetic Creams Dairy Creams Greases Stabilised Yoghurt
Time
Fig. 2.1.2g Thixotropic Fluids
Anti-thixotropic Fluids Viscosity increases with time under shear conditions. After shear ceases the viscosity will return to its original value - the time for recovery will vary with different fluids. As the name suggests anti-thixotropic fluids have opposite rheological characteristics to thixotropic fluids.
Time
Viscosity
Fig. 2.1.2h Anti-thixotropic Fluids
Typical fluids are: Vanadium Pentoxide Solution Rheomalactic Fluids Viscosity decreases with time under shear conditions but does not recover. Fluid structure is irreversibly destroyed.
Viscosity
Typical fluids are: Natural Rubber Latex Natural Yoghurt

Time
Fig. 2.1.2i Rheomalactic Fluids
Plastic Fluids Need a certain applied force (or yield stress) to overcome solid-like structure, before flowing like a fluid.
Stress
Y Where Y = Yield Stress
Typical fluids are: Barium X-ray Meal Chocolate Tomato Ketchup
Shear rate
Fig. 2.1.2j Plastic Fluids
It should be noted that some fluids would have both thixotropic and pseudoplastic behaviour.
Density in gases varies considerably with pressure and temperature but can be regarded as constant in fluids.
2.1.3 Density
The density of a fluid is its mass per unit of volume, usually expressed as kilograms per cubic metre (kg/m3) or pounds per cubic foot (lb/ft3). Density is usually designated by the symbol . 1 m of ethyl alcohol has a mass of 789 kg. i.e. Density = 0.789 kg/m3.
1 ft of ethyl alcohol has a mass of 49.2 lb. i.e. Density = 49.2 lb/ft3.
1 m
1
ft
1 ft
Mass of ethyl alcohol 789 kg
Mass of ethyl alcohol 49.2lb
1 m
Fig. 2.1.3a Density
2.1.4 Specific Weight

The specific weight of a fluid is its weight per unit volume and is usually designated by the symbol . It is related to density as follows: =xg where g is gravity.
The units of weight per unit volume are N/m3 or lbf/ft3. Standard gravity is as follows: g = 9.807 m/s2 g = 32.174 ft/s2
The specific weight of water at 20oC (68oF) and 1 atmosphere is as follows: =9790 N/m3 = 62.4 lbf/ft3 Note! - Mass should not be confused with weight. Weight is the force produced from gravity acting on the mass.
1 ft
2.1.5 Specific Gravity

1 m
1 m
1
1 m
The specific gravity of a fluid is the ratio of its density to the density of water. As this is a ratio, it does not have any units of measure. 1 m of ethyl alcohol has a mass of 789 kg - its density is 789 kg/m. 1 m of water has a mass of 1000 kg - its density is 1000 kg/m.
Mass of ethyl alcohol 789 kg
Mass of water 1000 kg
1 m
Fig. 2.1.5a Specific gravity
1 m
Specific Gravity of ethyl alcohol is:
789 kg/m 1000 kg/m
= 0.789
or
1 ft of ethyl alcohol has a mass of 49.2 lb - its density is 49.2 lb/ft. 1 ft of water has a mass of 62.4 lb - its density is 62.4 lb/ft. Specific Gravity of ethyl alcohol is: 49.2 lb/ft 62.4 lb/ft = 0.789
This resultant figure is dimensionless so the Specific Gravity (or SG) is 0.789. Temperature is a measure of the internal energy level in a fluid, usually expressed in units of degrees Centigrade (C) or degrees Fahrenheit (F).
2.1.6 Temperature
The temperature of the fluid at the pump inlet is usually of most concern as vapour pressure can have a significant effect on pump performance (see 2.1.8). Other fluid properties such as viscosity and density can also be affected by temperature changes. Thus a cooling of the product in the discharge line could have a significant effect on the pumping of a fluid. The temperature of a fluid can also have a significant affect on the selection of any elastomeric materials used. A temperature conversion table is given in section 14.3.11.
2.1.7 Flow Characteristics

When considering a fluid flowing in a pipework system it is important to be able to determine the type of flow. The connection between the velocity and the capacity of a fluid (similar to water) in different tube sizes is shown in table 14.6. Under some conditions the fluid will appear to flow as layers in a smooth and regular manner. This can be illustrated by opening a water tap slowly until the flow is smooth and steady. This type of flow is called laminar flow. If the water tap is opened wider, allowing the velocity of flow to increase, a point will be reached whereby the
stream of water is no longer smooth and regular, but appears to be moving in a chaotic manner. This type of flow is called turbulent flow. The type of flow is indicated by the Reynolds number. Velocity Velocity is the distance a fluid moves per unit of time and is given by equation as follows: In dimensionally consistent SI units Velocity V =Q A where V = fluid velocity (m/s) Q = capacity (m/s) A = tube cross sectional area (m)
Other convenient forms of this equation are: Velocity V = Q x 353.6 D where V = fluid velocity (m/s) Q = capacity (m/h) D = tube diameter (mm)
or
Velocity V
= Q x 0.409 D
where V = fluid velocity (ft/s) Q = capacity (US gall/min) D = tube diameter (in)
or
Velocity V
= Q x 0.489 D
where V = fluid velocity (ft/s) Q = capacity (UK gall/min) D = tube diameter (in)
Fluid velocity can be of great importance especially when pumping slurries and fluids containing solids. In these instances, a certain velocity may be required to prevent solids from settling in the pipework, which could result in blockages and changes in system pressure as the actual internal diameter of the pipe is effectively decreased, which could impact on pump performance.
V = velocity u max = maximum velocity Fig. 2.1.7a Laminar flow
Laminar Flow This is sometimes known as streamline, viscous or steady flow. The fluid moves through the pipe in concentric layers with the maximum velocity in the centre of the pipe, decreasing to zero at the pipe wall. The velocity profile is parabolic, the gradient of which depends upon the viscosity of the fluid for a set flow-rate.
Turbulent Flow This is sometimes known as unsteady flow with considerable mixing taking place across the pipe cross section. The velocity profile is more flattened than in laminar flow but remains fairly constant across the section as shown in fig. 2.1.7b. Turbulent flow generally appears at relatively high velocities and/or relatively low viscosities.
V = velocity u max = maximum velocity Fig. 2.1.7b Turbulent flow
Transitional Flow Between laminar and turbulent flow there is an area referred to as transitional flow where conditions are unstable and have a blend of each characteristic. This is a ratio of inertia forces to viscous forces, and as such, a useful value for determining whether flow will be laminar or turbulent. Reynolds Number (Re) Reynolds number for pipe flow is given by equation as follows: In dimensionally consistent SI units Re = DxVx where D = tube diameter (m) V = fluid velocity (m/s) = density (kg/m) = absolute viscosity (Pa.s)
Other convenient forms of this equation are: Re = DxVx where D = tube diameter (mm) V = fluid velocity (m/s) = density (kg/m) = absolute viscosity (cP)
or Re = 21230 x Q Dx where D = tube diameter (mm) Q = capacity (l/min) = absolute viscosity (cP)
or
Re
3162 x Q Dx
where D = tube diameter (in) Q = capacity (US gall/min) = kinematic viscosity (cSt)
or
Re
3800 x Q Dx
where D = tube diameter (in) Q = capacity (UK gall/min) = kinematic viscosity (cSt)
Since Reynolds number is a ratio of two forces, it has no units. For a given set of flow conditions, the Reynolds number will not vary when using different units. It is important to use the same set of units, such as above, when calculating Reynolds numbers. Re less than 2300 Laminar Flow (Viscous force dominates - high system losses) Transitional Flow (Critically balanced forces) Turbulent Flow (Inertia force dominates - low system losses)
Re in range 2300 to 4000 Re greater than 4000
Where transitional flow occurs, frictional loss calculations should be carried out for both laminar and turbulent conditions, and the highest resulting loss used in subsequent system calculations.
2.1.8 Vapour Pressure

Fluid (liquid form)
Pvp = Vapour pressure (external pressure required to maintain as a fluid) Fig. 2.1.8a Vapour pressure
Fluids will evaporate unless prevented from doing so by external pressure. The vapour pressure of a fluid is the pressure (at a given temperature) at which a fluid will change to a vapour and is expressed as absolute pressure (bar a or psia) - see 2.2.2. Each fluid has its own vapour pressure/temperature relationship. In pump sizing, vapour pressure can be a key factor in checking the Net Positive Suction Head (NPSH) available from the system (see 2.2.4). Temperature 0 C (32 F) 20o C (68o F) 100o C (212o F)
o
Vapour pressure (bar) 0.006 bar a (0.087 psia) 0.023 bar a (0.334 psia) 1.013 bar a (14.7 psia)
Water will boil (vaporise) at a temperature of: 0 C (32o F) if Pvp = 0.006 bar a (0.087 psia). 20 C (68o F) if Pvp = 0.023 bar a (0.334 psia). 100 C (212o F) if Pvp = 1.013 bar a (14.7 psia) (atmospheric conditions at sea level). In general terms Pvp: Is dependent upon the type of fluid. Increases at higher temperature. Is of great importance to pump inlet conditions. Should be determined from relevant tables. The Pvp for water at various temperatures is shown in section 14.4.
2.1.9 Fluids Containing Solids

It is important to know if a fluid contains any particulate matter and if so, the size and concentration. Special attention should be given regarding any abrasive solids with respect to pump type and construction, operating speed and shaft seals. Size of solids is also important, as when pumping large particles the pump inlet should be large enough for solids to enter the pump without bridging the pump inlet. Also the pump should be sized so the cavity created in the pump chamber by the pump elements is of sufficient size to allow satisfactory pump operation. Concentration is normally expressed as a percentage by weight (W/W) or volume (V/V) or a combination of both weight and volume (W/V).
2.2 Performance Data

2.2.1 Capacity (Flow Rate)
The capacity (or flow rate) is the volume of fluid or mass that passes a certain area per time unit. This is usually a known value dependent on the actual process. For fluids the most common units of capacity are litres per hour (l/h), cubic metres per hour (m/h) and UK or US gallons per minute (gall/min). For mass the most common units of capacity are kilogram per hour (kg/h), tonne per hour (t/h) and pounds per hour (lb/h).
2.2.2 Pressure
F = Force
Pressure is defined as force per unit area:
P= F A
where F is the force perpendicular to a surface and A is the area of the surface.
A 1 Fig. 2.2.2a Pressure 1
In the SI system the standard unit of force is the Newton (N) and area is given in square metres (m). Pressure is expressed in units of Newtons per square metre (N/m). This derived unit is called the Pascal (Pa). In practice Pascals are rarely used and the most common units of force are bar, pounds per square inch (lb/in) or psi, and kilogram per square centimetre (kg/cm). Conversion factors between units of pressure are given in section 14.3.5. Different Types of Pressure For calculations involving fluid pressures, the measurements must be relative to some reference pressure. Normally the reference is that of the atmosphere and the resulting measured pressure is called gauge pressure. Pressure measured relative to a perfect vacuum is called absolute pressure. Atmospheric Pressure The actual magnitude of the atmospheric pressure varies with location and with climatic conditions. The range of normal variation of atmospheric pressure near the earths surface is approximately 0.95 to 1.05 bar absolute (bar a) or 13.96 to 15.43 psi gauge (psig). At sea level the standard atmospheric pressure is 1.013 bar a or 14.7 psi absolute (bar a or psia).
Gauge Pressure Using atmospheric pressure as a zero reference, gauge pressure is the pressure within the gauge that exceeds the surrounding atmospheric pressure. It is a measure of the force per unit area exerted by a fluid, commonly indicated in units of barg (bar gauge) or psig (psi gauge). Absolute Pressure Is the total pressure exerted by a fluid. It equals atmospheric pressure plus gauge pressure, indicated in units of bar a (bar absolute) or psia (psi absolute). Absolute Pressure = Gauge Pressure + Atmospheric Pressure Vacuum This is a commonly used term to describe pressure in a pumping system below normal atmospheric pressure. This is a measure of the difference between the measured pressure and atmospheric pressure expressed in units of mercury (Hg) or units of psia.
0 psia = 760 mm Hg (29.9 in Hg). 14.7 psia = 0 mm Hg (0 in Hg).

Inlet (Suction) Pressure This is the pressure at which the fluid is entering the pump. The reading should be taken whilst the pump is running and as close to the pump inlet as possible. This is expressed in units of absolute bar a (psia) or gauge bar g (psig) depending upon the inlet conditions. Outlet (Discharge) Pressure This is the pressure at which the fluid leaves the pump. Again this reading should be taken whilst the pump is running and as close to the pump outlet as possible. The reading is expressed in units of gauge bar (psig). Differential Pressure This is the difference between the inlet and outlet pressures. For inlet pressures above atmospheric pressure the differential pressure is obtained by subtracting the inlet pressure from the outlet pressure. For inlet pressures below atmospheric pressure the differential pressure is obtained by adding the inlet pressure to the outlet pressure. It is therefore the total pressure reading and is the pressure against which the pump will have to operate. Power requirements are to be calculated on the basis of differential pressure.
Example: Inlet Pressure above Atmospheric Pressure

Outlet Inlet Differential
4 bar g (58 psi g)
5.013 bar a (72.7 psi a)
0 bar g (0 psi g)
1.5 bar g (21.75 psi g) 1.013 bar a 0 bar g (14.7 psi a) (0 psi g) 0 bar a (0 psi a)
1.013 bar a (14.7 psi a)
Differential = 4 - 1.5 = 2.5 bar or = 58 - 21.75 = 36.25 psi
Example: Inlet Pressure below Atmospheric Pressure

Outlet Inlet Differential
4 bar g (58 psi g)
5.013 bar a (72.7 psi a)
0 bar g (0 psi g)
1.013 bar a (14.7 psi a) 0 bar a (0 psi a)
0 bar g (0 psi g)
1.013 bar a (14.7 psi a) 0.5 bar a (7.25 psi a) 0 bar a (0 psi a) Differential
= 4 + (1.013 - 0.5) = 4.513 bar or = 58 + (14.7 -7.25) = 65.45 psi
Fig. 2.2.2b Differential pressure
The relationship of elevation equivalent to pressure is commonly referred to as head.

Fig. 2.2.2c Relationship of pressure to elevation
The Relationship Between Pressure and Elevation In a static fluid (a body of fluid at rest) the pressure difference between any two points is in direct proportion only to the vertical distance between the points. The same vertical height will give the same pressure regardless of the pipe configuration in between.
This pressure difference is due to the weight of a column of fluid and can be calculated as follows: In dimensionally consistent SI units Static Pressure (P) = x g x h where P = Pressure/head (Pa) = density of fluid (kg/m3) g = gravity (m/s2) h = height of fluid (m) Other convenient forms of this equation are: Static Pressure (P) = h (m) x SG 10 (bar)
or
Static Pressure (P)
h (ft) x SG 2.31
(psi)
A pump capable of delivering 35 m (115 ft) head will produce different pressures for fluids of differing specific gravities.
Water Slurry Solvent
35 m (115ft). 3.5 bar (50 psi)
35 m (115ft) 4.9 bar (70 psi)
35 m (115ft) 2.5 bar (35 psi)
SG 1.0
SG 1.4
SG 0.7
Fig. 2.2.2d Relationship of elevation to pressure
A pump capable of delivering 3.5 bar (50 psi) pressure will develop different amounts of head for fluids of differing specific gravities.
Water Slurry Solvent
35 m (115 ft). SG 1.0 3.5 bar (50 psi)
25 m (82 ft). SG 1.4 3.5 bar (50 psi)
50 m (165 ft). SG 0.7 3.5 bar (50 psi)
Fig. 2.2.2e Relationship of elevation to pressure
Below are terms commonly used to express different conditions in a pumping system which can be expressed as pressure units (bar or psi) or head units (m or ft). Flooded Suction This term is generally used to describe a positive inlet pressure/head, whereby fluid will readily flow into the pump inlet at sufficient pressure to avoid cavitation (see 2.2.3). Static Head The static head is a difference in fluid levels. Static Suction Head This is the difference in height between the fluid level and the centre line of the pump inlet on the inlet side of the pump. Static Discharge Head This is the difference in height between the fluid level and the centre line of the pump inlet on the discharge side of the pump.
Total Static Head The total static head of a system is the difference in height between the static discharge head and the static suction head. Friction Head This is the pressure drop on both inlet and discharge sides of the pump due to frictional losses in fluid flow. Dynamic Head This is the energy required to set the fluid in motion and to overcome any resistance to that motion. Total Suction Head The total suction head is the static suction head less the dynamic head. Where the static head is negative, or where the dynamic head is greater than the static head, this implies the fluid level will be below the centre line of the pump inlet (ie suction lift). Total Discharge Head The total discharge head is the sum of the static discharge and dynamic heads. Total Head Total head is the total pressure difference between the total discharge head and the total suction head of the pump.The head is often a known value. It can be calculated by means of different formulas if the installation conditions are specified. Total head H Total discharge head Ht Total suction head Hs Where: H Hs Ht hs ht hfs hft Ps Pt = = = Ht ( Hs) ht + hft + pt hs hfs + ( ps)
= Total head. = Total suction head. = Total discharge head. = Static suction head. = Static discharge head. = Pressure drop in suction line. = Pressure drop in discharge line. = Vacuum or pressure in a tank on suction side. = Pressure in a tank on discharge side.
In general terms:
p > 0 for pressure. p < 0 for vacuum. p = 0 for open tank. hs > 0 for flooded suction. hs < 0 for suction lift.
Fig. 2.2.2f Flooded suction and open discharge tanks
Fig. 2.2.2g Flooded suction and closed discharge tanks
Fig. 2.2.2h Suction lift and open discharge tanks
Fig. 2.2.2i Suction lift and closed discharge tanks
Pressure drop is the result of frictional losses in pipework, fittings and other process equipment etc.
Pressure Drop Manufacturers of processing equipment, heat exchangers, static mixers etc, usually have data available for pressure drop. These losses are affected by fluid velocity, viscosity, tube diameter, internal surface finish of tube and tube length. The different losses and consequently the total pressure drop in the process are, if necessary, determined in practice by converting the losses into equivalent straight length of tube which can then be used in subsequent system calculations. For calculations on water like viscosity fluids, the pressure drop can be determined referring to the Pressure Drop Curve (see 14.5) as shown in Example 1. For higher viscosity fluids, a viscosity correction factor is applied to the tube fittings by multiplying the resultant equivalent tube length by the figures shown below - see Example 2.
Table 2.2.2a
Viscosity - cP Correction Factor
1 - 100 1.0
101 - 2000 0.75
2001 - 20000 20001 - 100000 0.5 0.25
Example 1:
Process: Pumping milk from tank A to tank G. Q = 8 m3/h (35 US gall/min). Tubes, valves and fittings: A: Tank outlet dia. 63.5 mm (2.5 in). A-B: 4 m (13 ft) tube dia. 63.5 mm (2.5 in). A-B: 1 off bend 90 deg. dia. 63.5 mm (2.5 in). B-C: 20 m (66 ft) tube dia. 51 mm (2 in). C: Seat valve type SRC-W-51-21-100. C-E: 15 m (49 ft) tube dia. 51 mm (2 in). B-E: 3 off bend 90 deg. dia. 51 mm (2 in). D: Non-return valve type LKC-2, 51 mm (2 in). E: Seat valve type SRC-W-51-21-100. E-F: 46 m (151 ft) tube dia. 38 mm (1.5 in). E-F: 4 off bend 90 deg. dia. 38 mm (1.5 in). F: Seat valve type SRC-W-38-21-100. The pressure drop through the tubes, valves and fittings is determined as equivalent tube length, so that the total pressure drop can be calculated. The conversion into equivalent tube length is carried out by reference to section 14.7. This results in the following equivalent tube length for the different equipment as shown in the following tables:
Fig. 2.2.2j Example
Table 2.2.2b
Equipment
Equivalent ISO Tube Length (m) 38 mm 51 mm 63.5 mm 1 (estimated) 4 1x1 20 15 10 3x1 12 14 46 4x1 4 54 74 6
Tank outlet
A-B Tube A-B Bend 90 deg. B-C Tube C-E C-E B-E D E E-F E-F F Total Tube SRC seat valve, pos 3 Bend 90 deg. LKC-2 non-return valve SRC, seat valve, pos.5 Tube Bend 90 deg. SRC seat valve, pos.3
Table 2.2.2c
Equipment
Equivalent ISO Tube Length (ft) 1.5 in 2 in 2.5 in 3 (estimated) 13 1x3 66 49 33 3x3 39 46 151 4x3 13 176 242 19
A A-B A-B B-C C-E C-E B-E D E E-F E-F F Total
Tank outlet Tube Bend 90 deg. Tube Tube SRC seat valve, pos.3 Bend 90 deg. LKC-2 non-return valve SRC seat valve, pos.5 Tube Bend 90 deg. SRC seat valve, pos.3
As viewed from the tables above the pressure drop through the different equipment corresponds to the following equivalent tube length. 38 mm (1.5 in) tube: 51 mm (2 in) tube: 63.5 mm (2.5 in) tube: Length = 54 m (176 ft). Length = 74 m (242 ft). Length = 6 m (19 ft).
The pressure drop through 100 m of tube for sizes 38 mm, 51 mm and 63.5 mm is determined by means of the following curve, also shown in 14.5.
~ 13.2
~ 3.0 ~ 1.1
Q = 8 m3/h
Fig. 2.2.2k Pressure drop curve 26 Alfa Laval Pump Handbook
The total pressure drop H in the process is consequently calculated as follows: 38 mm: H = 54 x 13.2 = 7.13 m 100 H = 74 x 3.0 = 2.22 m 100 H = 6 x 1.1 = 0.07 m 100
51 mm:
63.5 mm:
H = 7.13 + 2.22 + 0.07 = 9.42 m 9.4 m ( 1 bar) or
1.5 in:
H = 176 x 43 = 23.1 ft 328 H = 242 x 10 = 7.4 ft 328 H = 19 x 4 = 0.2 ft 328
2 in:
2.5 in:
H = 23.1 + 7.4 + 0.2 = 30.7 ft 31 ft ( 14 psi)

Example 2: Process: Pumping glucose with a viscosity of 5000 cP from a flooded suction through discharge pipeline as follows. Tubes, valves and fittings: 30 m (98 ft) tube dia. 51 mm (2 in). 20 m (66 ft) tube dia. 76 mm (3 in). 2 off Non-return valves 51 mm (2 in). 6 off Bend 90 deg. dia. 51 mm (2 in). 4 off Bend 90 deg. dia. 76 mm (3 in). 3 off Tee (out through side port) 51 mm (2 in). The pressure drop through the tubes, valves and fittings is determined as equivalent tube length so that the total pressure drop can be calculated.
For the pipe fittings the conversion into equivalent tube length is carried out by reference to tables 14.7. This results in the following equivalent tube length for the different fittings as shown below:
Table 2.2.2d Fittings Equivalent ISO Tube Length (m) 51 mm 76 mm 2 x 12 6x1 4x1 3x3 39 4
Non-return valve Bend 90 deg. Bend 90 deg. Tee Total Table 2.2.2e
Fittings
Equivalent ISO Tube Length (ft) 2 in 3 in 2 x 39 6x3 4x3 3 x 10 126 12
Non-return valve Bend 90 deg. Bend 90 deg. Tee Total
As viewed from the tables above the pressure drop through the different fittings corresponds to the following equivalent tube length. Tube dia. 51 mm (2 in): Length = 39 m (126 ft). Tube dia. 76 mm (3 in): Length = 4 m (12 ft). Applying the viscosity correction factor for 5000 cP the equivalent tube length is now: Tube dia. 51 mm (2 in): Length = 39 m (126 ft) x 0.5 = 19.5 m (63 ft) Tube dia. 76 mm (3 in): Length = 4 m (12 ft) x 0.5 = 2 m (6 ft)
These figures of 19.5 m (63 ft) and 2 m (6 ft) would be added to the straight tube lengths given as shown below, and subsequently used in calculating the discharge pressure at the flow rate required. Tube dia. 51 mm (2 in): 30 m (98 ft) + 19.5 m (63 ft) = 49.5 m (161 ft) + Tube dia. 76 mm (3 in): 20 m (66 ft) + 2 m (6 ft) = 22 m (72 ft)
The friction losses in a pipework system are dependent upon the type of flow characteristic that is taking place. The Reynolds number (Re) is used to determine the flow characteristic, see 2.1.7.
Friction Loss Calculations Since laminar flow is uniform and predictable it is the only flow regime in which the friction losses can be calculated using purely mathematical equations. In the case of turbulent flow, mathematical equations are used, but these are multiplied by a co-efficient that is normally determined by experimental methods. This co-efficient is known as the Darcy friction factor (fD). The Miller equation given below can be used to determine the friction losses for both laminar and turbulent flow in a given length of pipe (L). In dimensionally consistent SI units:
Pf = fD x L x x V2 Dx2
Where: Pf fD L D V = pressure loss due to friction (Pa). = Darcy friction factor. = tube length (m). = tube diameter (m). = fluid velocity (m/s). = density of fluid (kg/m3).
Other convenient forms of this equation are:
Pf = 5 x SG x fD x L x V D
Where: Pf fD L D V SG or = pressure loss due to friction (bar). = Darcy friction factor. = tube length (m). = tube diameter (mm). = fluid velocity (m/s). = specific gravity.
Pf = 0.0823 x SG x fD x L x V D
Where: Pf fD L D V SG = pressure loss due to friction (psi). = Darcy friction factor. = tube length (ft). = tube diameter (in). = fluid velocity (ft/s). = specific gravity.
For laminar flow, the Darcy friction factor (fD) can be calculated directly from the equation: fD = 64 Re
The relative roughness of pipes varies with diameter, type of material used and age of the pipe. It is usual to simplify this by using an relative roughness (k) of 0.045 mm, which is the absolute roughness of clean commercial steel or wrought iron pipes as given by Moody.
For turbulent flow, the Darcy friction factor (fD) has to be determined by reference to the Moody diagram (see section 14.8). It is first necessary to calculate the relative roughness designated by the symbol . Where: =k D = relative roughness which is the average heights of the pipe internal surface peaks (mm). = internal pipe diameter (mm).
k D The term cavitation is derived from the word cavity, meaning a hollow space.
2.2.3 Cavitation
Cavitation is an undesirable vacuous space in the inlet port of the pump normally occupied by fluid. The lowest pressure point in a pump occurs at the pump inlet - due to local pressure reduction part of the fluid may evaporate generating small vapour bubbles. These bubbles are carried along by the fluid and implode instantly when they get into areas of higher pressure. If cavitation occurs this will result in loss of pump efficiency and noisy operation. The life of a pump can be shortened through mechanical damage, increased corrosion and erosion when cavitation is present. When sizing pumps on highly viscous fluids care must be taken not to select too high a pump speed so as to allow sufficient fluid to enter the pump and ensure satisfactory operation. For all pump application problems, cavitation is the most commonly encountered. It occurs with all types of pumps, centrifugal, rotary or reciprocating. When found, excessive pump speed and/or adverse suction conditions will probably be the cause and reducing pump speed and/or rectifying the suction condition will usually eliminate this problem.
Cavitation should be avoided at all costs.
2.2.4 Net Positive Suction Head (NPSH)

In addition to the total head, capacity, power and efficiency requirements, the condition at the inlet of a pump is critical. The system on the inlet side of the pump must allow a smooth flow of fluid to enter the pump at a sufficiently high pressure to avoid cavitation. This is called the Net Positive Suction Head, generally abbreviated NPSH. Pump manufacturers supply data about the net positive suction head required by their pumps (NPSHr) for satisfactory operation. When selecting a pump it is critical the net positive suction head available (NPSHa) in the system is greater than the net positive suction head required by the pump. For satisfactory pump operation: NPSHa > NPSHr N.I.P.A. > N.I.P.R. NPSHa is also referred to as N.I.P.A. (Net Inlet Pressure Available) and NPSHr is also referred to as N.I.P.R. (Net Inlet Pressure Required). A simplified way to look at NPSHa or N.I.P.A. is to imagine a balance of factors working for (static pressure and positive head) and against (friction loss and vapour pressure) the pump. Against
Fig. 2.2.4a NPSH balance
For
Providing the factors acting for the pump outweigh those factors acting against, there will be a positive suction pressure.
The value of NPSHa or N.I.P.A. in the system is dependent upon the characteristic of the fluid being pumped, inlet piping, the location of the suction vessel, and the pressure applied to the fluid in the suction vessel. This is the actual pressure seen at the pump inlet. It is important to note, it is the inlet system that sets the inlet condition and not the pump. It is calculated as follows:
NPSHa = Pressure acting on or surface of liquid (Pa) N.I.P.A. +ve -ve +ve -ve + Static suction head (hs) Pressure drop (hfs) Vapour pressure (Pvp)
hs
Fig. 2.2.4b NPSH calculation
NPSHa or N.I.P.A. = Pa hs - hfs - Pvp
Where: Pa hs hfs Pvp or
= Pressure absolute above fluid level (bar). = Static suction head (m). = Pressure drop in suction line (m). = Vapour pressure (bar a).
Where: Pa hs hfs Pvp
= Pressure absolute above fluid level (psi). = Static suction head (ft). = Pressure drop in suction line (ft). = Vapour pressure (psia).
It is important the units used for calculating NPSHa or N.I.P.A. are consistent i.e. the total figures should be in m or ft. For low temperature applications the vapour pressure is generally not critical and can be assumed to be negligible.
Example 1:
Process: Water at 50 C (122o F). 1.5 m Pa hs hfs Pvp = Pressure absolute above fluid level (1 bar = 10 m) (14.7 psi = 33.9 ft). = Static suction head (3.5 m) (11.5 ft). = Pressure drop in suction line (1.5 m) (5 ft). = Vapour pressure (0.12 bar a = 1.2 m) (1.8 psia = 4 ft).
3.5 m
Fig. 2.2.4c Example
NPSHr of pump selected = 3.0 m (10 ft). NPSHa
= Pa - hs - hfs - Pvp = Pa - hs - hfs - Pvp = 10 - 3.5 - 1.5 - 1.2 (m) or = 33.9 - 11.5 - 5 - 4 (ft) = 3.8 m = 13.4 ft
As NPSHa is greater than NPSHr, no cavitation will occur under the conditions stated.
Example 2:
0.5 bar
Process: Water at 75 C (167o F). Pa = Pressure absolute above fluid level (0.5 bar = 5 m) (7 psi = 16 ft). = Static suction head (1.5 m) (5 ft). = Pressure drop in suction line (1.0 m) (3 ft). = Vapour pressure (0.39 bar a = 3.9 m) (5.7 psia = 13 ft).
1.5 m
hs hfs Pvp
Fig. 2.2.4d Example
NPSHr of pump selected = 3.0 m (10 ft). NPSHa = Pa + hs - hfs - Pvp = 5 + 1.5 - 1.0 - 3.9 (m) = 1.6 m
= Pa + hs - hfs - Pvp or = 16 + 5 - 3 - 13 (ft) = 5 ft
As NPSHa is less than NPSHr, cavitation will occur under the conditions stated.
Example 3:
Process: Glucose at 50 C (122o F). Pa hs hfs Pvp = Pressure absolute above fluid level (1 bar = 10 m) (14.7 psi = 33.9 ft). = Static suction head (1.5 m) (5 ft). = Pressure drop in suction line (9.0 m) (30 ft). = Vapour pressure (assumed negligible = 0 m) (0 ft).
Fig. 2.2.4e Example
NPSHr of pump selected = 3.0 m (10 ft). NPSHa = Pa + hs - hfs - Pvp = 10 + 1.5 - 9.0 - 0 (m) = 2.5 m
= Pa + hs - hfs - Pvp or = 33.9 + 5 - 30 - 0 (ft) = 8.9 ft
As NPSHa is less than NPSHr, cavitation will occur under the conditions stated. From the NPSHa formula it is possible to check and optimise the conditions which affect NPSHa. The effects are shown as follows:
Fig. 2.2.4f Positive effect
Fig. 2.2.4g Positive effect
Fig. 2.2.4h Negative effect
Vapour pressure (Temperature dependent)
Fig. 2.2.4i Negative effect
Fig. 2.2.4j Negative effect
Fig. 2.2.4k Negative effect
Suggestions for avoiding cavitation: Keep pressure drop in the inlet line to a minimum i.e. length of line as short as possible, diameter as large as possible, and minimal use of pipe fittings such as tees, valves etc. Maintain a static head as high as possible. Reduce fluid temperature, although caution is needed as this may have an effect of increasing fluid viscosity, thereby increasing pressure drop.
2.2.5 Pressure Shocks (Water Hammer)

The term shock is not strictly correct as shock waves only exist in gases. The pressure shock is really a pressure wave with a velocity of propagation much higher than the velocity of the flow, often up to 1400 m/s for steel tubes. Pressure waves are the result of rapid changes in the velocity of the fluid in especially long runs of piping. The following causes changes in fluid velocity: Valves are closed or opened. Pumps are started or stopped. Resistance in process equipment such as valves, filters, meters, etc. Changes in tube dimensions. Changes in flow direction. The major pressure wave problems in process plants are usually due to rapidly closed or opened valves. Pumps, which are rapidly/ frequently started or stopped, can also cause some problems. When designing pipework systems it is important to keep the natural frequency of the system as high as possible by using rigid pipework and as many pipework supports as possible, thereby avoiding the excitation frequency of the pump. Effects of pressure waves: Noise in the tube. Damaged tube. Damaged pump, valves and other equipment. Cavitation. Velocity of propagation The velocity of propagation of the pressure wave depends on: Elasticity of the tubes. Elasticity of the fluid. The tubes support.
When for example, a valve is closed, the pressure wave travels from the valve to the end of the tube. The wave is then reflected back to the valve. These reflections are in theory continuing but in practice the wave gradually attenuates cancelled by friction in the tube. A pressure wave as a result of a pump stopping is more damaging than for a pump starting due to the large change in pressure which will continue much longer after a pump is stopped compared to a pump starting. This is due to the low fluid velocity which results in a relatively small damping of the pressure waves. A pressure wave induced as a result of a pump stopping can result in negative pressure values in long tubes, i.e. values close to the absolute zero point which can result in cavitation if the absolute pressure drops to the vapour pressure of the fluid. Precautions Pressure waves are caused by changes in the velocity of the liquid in especially long runs of tube. Rapid changes in the operating conditions of valves and pump are the major reasons to the pressure waves and therefore, it is important to reduce the speed of these changes. There are different ways to avoid or reduce pressure waves which are briefly described below. Correct flow direction Incorrect flow direction through valves can induce pressure waves particularly as the valve functions. With air-operated seat valves incorrect direction of flow can cause the valve plug to close rapidly against the valve seat inducing pressure waves. Figs 2.2.5a and 2.2.5b specify the correct and incorrect flow direction for this type of valve. Correct flow directions in the process plant can reduce or even prevent pressure wave problems.
Correct
Incorrect
Fig. 2.2.5a Correct flow direction through seat valve
Fig. 2.2.5b Incorrect flow direction through seat valve
Damping of valves The pressure wave induced by a seat valve can be avoided or minimised by damping the movement of the valve plug. The damping is carried out by means of a special damper (see fig. 2.2.5c).
Fig. 2.2.5c Oil damper for seat valve
Speed control of pumps Speed control of a pump is a very efficient way to minimise or prevent pressure waves. The motor is controlled by means of a soft starter or a frequency converter so that the pump is: Started at a low speed which is slowly increased to duty speed. Stopped by slowly decreasing from duty speed down to a lower speed or zero.
The risk of power failure should be taken into consideration when using speed control against pressure waves. Equipment for industrial processes There is various equipment available to reduce pressure waves such as: Pressure storage tanks. Pressure towers. Damped or undamped non-return valves.
These however, may not be suitable for hygienic processes and further advice may be required before they are recommended or used in such installations.
Pump Selection
3. Pump Selection
This section gives an overview of the pump ranges currently available from Alfa Laval and which particular pumps to apply within various application areas.
As demands on processes increase, major factors evolve such as the quality of products and process profitability. In view of this, the correct selection of a pump is of great importance. The pump must be able to carry out various duties under differing conditions. Some of these are as follows: Transfer various types of fluids/products. Gentle treatment of the fluids/products. Overcome different losses and pressure drops in the system. Provide hygienic, economical and long lasting operation. Ensure easy and safe installation, operation and maintenance. As pumps are used in different locations and stages of a process the need for the correct pump in the right place has become increasingly important. It is therefore necessary to be aware of the various problems that might be encountered when selecting a pump. Some pump problems can be: The correct type of pump for the right application. The correct design of pump. The correct selection of pump with regard to inlet and outlet conditions, product data, operating conditions etc. Correct selection of shaft seals. Correct selection of drive units.
Pump Selection
3.1 General Applications Guide

The table shown below gives a general guide as to the various types of Alfa Laval pump that may be required to suit the application.
General Requirements Product/Fluid Requirements Max. Viscosity Max. Pumping Temperature Min. Pumping Temperature Ability to pump abrasive products Ability to pump fluids containing air or gases Ability to pump shear sensitive media Ability to pump solids in suspension CIP capability (sanitary) Dry running capability (when fitted with flushed/quench mechanical seals) Self Draining capability Performance Requirements Max. Capacity - m/hr Max. Capacity - US gall/min Max. Discharge Pressure - bar Max. Discharge Pressure - psig Ability to vary flow rate Suction Lift capability (primed wet) Suction Lift capability (unprimed - dry) Drive Availability Air motor Diesel engine Electric motor Hydraulic motor Petrol engine Compliance with International Standards and Guidelines 3-A FDA EHEDG Table 3.1a Yes Yes Yes Yes Yes No Yes Yes Yes No No Yes Possible No No No Yes Possible No Yes Yes Yes Yes Yes 440 1936 20 290 Fair Recommended Not recommended 80 352 5.5 80 Not recommended Recommended Not recommended 115 506 20 290 Recommended Recommended Fair 1000 cP 140C (284 F) - 10C (14oF) Not recommended Not recommended Fair Fair Recommended Recommended Recommended
o
Centrifugal
Liquid Ring
Rotary Lobe
200 cP 140C (284 F) - 10C (14oF) Not recommended Recommended Not recommended Not recommended Recommended Recommended Recommended
o
1000000 cP 200C (392oF) - 20C (-4oF) Fair Fair Recommended Recommended Recommended Recommended Recommended
Pump Selection
3.2 Pumps for Sanitary Applications

Alfa Laval Pump Ranges
Pump Ranges from Alfa Laval
Centrifugal
Liquid Ring
Rotary Lobe
LKH LKHP High Pressure LKHI
LKH Multistage LKHSP LKH Ultra Pure
MR
SRU
SX
Fig. 3.2a Pump ranges
The following table illustrates which Alfa Laval pump ranges can be used in various sanitary application areas. A detailed description of these pump ranges is given in section 4.
Pump Type Pump Range Application Area
Soap and Detergent
Pharmaceutical
Confectionery
Other Food
Soft Drink
Brewery
Sugar
Centrifugal
LKH LKH-Multistage LKHP-High Pressure LKHSP LKHI LKH-Ultra Pure SRU SX
! ! ! ! ! ! !
! !
! ! !
! ! ! ! ! ! ! !
! ! ! ! ! ! ! !
! ! ! ! ! ! !
! !
! ! ! ! ! ! ! !
! ! ! ! !
! ! !
Rotary Lobe
Table 3.2a
The Liquid Ring pump is used in most of these sanitary application areas dedicated for CIP and tank emptying duties. Brewery Alfa Laval Centrifugal and Rotary Lobe pumps are used in most process stages of brewing from wort handling to beer pasteurisation and filling. Generally, rotary lobe pumps best perform high fluid viscosity applications, such as liquid sugar tanker offloading and malt syrups, whereas low fluid viscosity applications, such as beer and water chilling, are mostly carried out using centrifugal pumps. During the fermentation process, rotary lobe pumps with their gentle pumping action are ideally used handling yeast containing delicate cells.
Water
Dairy
Pump Selection
Confectionery Alfa Laval is a major supplier of pumping equipment to this industry, providing pumps to all the major confectionery companies. Rotary lobe pumps being used on high viscosity products such as chocolate, glucose, biscuit cream and fondant. Confectionery products that contain particulate matter, such as fruit pie fillings, can be handled with the rotary lobe pump. Centrifugal pumps can be commonly found on fat and vegetable oil applications. Dairy Alfa Laval Centrifugal and Rotary Lobe pumps, with their hygienic construction and conforming to 3-A standards (see section 11), are used extensively throughout the dairy industry on milk processing, cream and cultured products such as yoghurt. Other Food Other Food means other than Confectionery, Dairy and Sugar generally Alfa Laval Centrifugal and Rotary Lobe pumps can be found on general transfer duties handling products such as petfood, sauces and flavourings. Pharmaceutical Alfa Laval Centrifugal and Rotary Lobe pumps can be found on many applications within this industry where hygiene and corrosion resistance is paramount, such as cosmetic creams, protein solutions, toothpaste, perfume, shampoo and blood products. Soap and Detergent Alfa Laval Centrifugal and Rotary Lobe pumps can be found on many applications within this industry, handling products such as neat soap, sulphonic acid, fabric conditioner, dishwash liquid, fatty acid, lauryl ether sulphate, liquid detergent and surfactants. Soft Drink Alfa Laval Centrifugal pumps are mainly used on applications handling thin liquid sugar solutions, water and flavourings. Alfa Laval Rotary Lobe pumps are mainly used on applications handling high viscosity fruit juice concentrates. Sugar Alfa Laval Rotary Lobe pumps, with their ability to handle highly viscosity abrasive products, can be found within many areas of sugar refined products requiring hygienic handling, such as high boiled sugars, glucose solutions and sugar syrups used in confectionery, bakery, brewing and carbonated soft drinks.
Pump Selection
Water Alfa Laval Centrifugal pumps provide a low cost effective solution for high purity water and water like applications.
3.3 PumpCAS Selection and Configuration Tool

Pump selection for both Centrifugal and Rotary Lobe Pumps can be made by the use of Alfa Lavals PumpCAS selection program. This program prompts the user to enter pump duty information and selects the pump from the product range most suited to their specific application. The program selects both centrifugal and rotary lobe pumps and provides the user with a comparison of features enabling the most appropriate technology to be chosen. If one or other technology is not suited to a specific application (this could be due to physical limitations and or fluid characteristics) the program will advise the user, and recommend an alternative solution. As well as performing the pump selection, PumpCAS also extracts data from a comprehensive liquids database enabling it to suggest viscosity, SG, maximum speed, elastomer compatibility and primary seal configuration. After the pump has been selected, the user will be assisted to complete a detailed pump unit specification. This will include additional options such as pressure relief valves, heating or cooling devices, connection specifications etc. for which the price of the pump and its configuration code (item number) will be automatically generated aiding the quotation and/or ordering process. If you would like a copy of the Alfa Laval PumpCAS Selection and Configuration Tool please contact your local Alfa Laval sales company. In addition, PumpCAS will also provide detailed parts list for the pump with item numbers with all recommended spare parts identified and priced. Dimensional details in the form of general arrangement drawings can also be generated. A link to all technical information that may be required to accompany the quotation such as Operating manuals, generic or specific performance curves, and technical data sheets will also be provided, along with direct access to this Alfa Laval Pump Handbook for any additional supporting information that may be required.
Pump Selection
Flexibility has been built in to the software to enable specific enquiries to be answered without the need to complete a full pump selection. For example, recommended spares lists can be extracted based on an existing configuration code or direct access to technical information relating to a specific pump technology is possible. The liquids database contained within PumpCAS is based on rheological tests performed over many years on end users liquids at Alfa Lavals chemical laboratory, and will be continually added to as additional products are tested. All information is offered for guidance purposes only.
Pump Description
4. Pump Description
This section gives a description of Alfa Laval pump ranges including design, principle of operation and pump model types.
4.1 Centrifugal Pumps

4.1.1 General
The Alfa Laval range of Centrifugal Pumps has been designed specially for use in the food, dairy, beverage, pharmaceutical and light chemical industries. Centrifugal pumps including multi-stage designs and those for high inlet pressure, can handle most low viscosity applications. Centrifugal pumps can provide the most cost effective solution. Attributes include: High efficiency. Low power consumption. Low noise level. Low NPSH requirement. Easy maintenance.
Pump Description
4.1.2 Principle of Operation

Fluid is directed to the impeller eye and is forced into a circular movement by the rotation of the impeller vanes. As a result of this rotation, the impeller vanes transfer mechanical work to the fluid in the impeller channel, which is formed by the impeller vanes. The fluid is then pressed out of the impeller by means of centrifugal force and finally leaves the impeller channel with increased pressure and velocity. The velocity of the fluid is also partly converted into pressure by the pump casing before it leaves the pump through the outlet. The principle of the multi-stage centrifugal pump is the same as the conventional centrifugal pump. The pump consists, however, of several impellers (several stages) which increase the pressure from one stage to another but flow rate is unchanged. The multi-stage centrifugal pump operates as if several conventional centrifugal pumps are connected in series.
Fig. 4.1.2a Principle of operation
Fig. 4.1.2b Multistage centrifugal pump
4.1.3 Design
In general the Alfa Laval centrifugal pump does not contain many parts, with the pumphead being connected to a standard electric motor. The impeller is fixed onto the pump shaft which is housed in a pump casing and back plate these components are described below: Impeller The impeller is of cast manufacture and open type; i.e. the impeller vanes are open in front. This type allows visual inspection of the vanes and the area between them. A semi-open impeller is also available which is easy to clean and suitable for polishing.
Fig. 4.1.3a Semi-open impeller
The impeller has two or multiple vanes depending on the type of centrifugal pump. The impeller diameter and width will vary dependent upon the duty requirements.
Pump Description
Pump Casing The pump casing is of pressed steel manufacture, complete with male screwed connections and can be supplied with fittings or clamp liners. The pump casing is designed for multi position outlet, with 360 flexibility.
Fig. 4.1.3b Pump casing
Fig. 4.1.3c 360o flexibility
Back Plate The back plate is of pressed steel manufacture, which together with the pump casing form the actual fluid chamber in which the fluid is transferred by means of the impeller.
Fig. 4.1.3d Back plate
Mechanical Seal The connection between the motor shaft/pump shaft and the pump casing is sealed by means of a mechanical seal, which is described in section 6. Shroud and Legs Most pump types are fitted with shrouds and adjustable legs. The shroud is insulated to keep noise to a minimum and protect the motor against damage. Please note Alfa Laval Centrifugal pumps for the USA market are supplied without shrouds.
Fig. 4.1.3e Pump with shroud and legs
Pump Description
Pump Shaft/Connections Most pumps have stub shafts that are fixed to the motor shafts by means of compression couplings, eliminating the use of keyways. The stub shaft assembly design provides a simple, yet secure method of drive that reduces vibration and noise. On the multistage centrifugal pump the length of the pump shaft will differ depending upon the number of impellers fitted.
Fig. 4.1.3f Compression coupling
Adaptor Most pumps are fitted with a standard IEC electric motor. The connection between the motor and back plate is made by means of an adaptor, which can be attached to any standard IEC or C-frame electric motor. Pumps supplied with direct coupled motors have no adaptors.
Fig. 4.1.3g Adapter
4.1.4 Pump Range

The Alfa Laval Centrifugal Pump portfolio comprises different ranges as follows: LKH Range The LKH pump is a highly efficient and economical centrifugal pump, meeting sanitary requirements with gentle product treatment and chemical resistance.
Fig. 4.1.4a LKH
Fig. 4.1.4b LKH (USA version)
The LKH range is available in twelve sizes: LKH-5, -10, -15, -20, -25, -35, -40, -45, -50, -60, -70 and -80. Flow rates for 50 Hz up to 440 m/h (1936 US gall/min) and differential pressures up to 11.5 bar (165 psig) and for 60 Hz up to 440 m3/h (1936 US gall/min) and differential pressure up to 16 bar (230 psig).
Pump Description
LKH-Multistage Range These pumps are primarily used in applications with high outlet pressure and low capacity requirements such as breweries, reverse osmosis and ultra-filtration. The pumps are available as two, three or four stage models (i.e. pumps fitted with two, three or four impellers respectively).
Fig. 4.1.4c LKH-Multistage
Fig. 4.1.4d LKH-Multistage (USA version)
The LKH-Multistage range is available in six sizes.
Pump Size LKH-112 LKH-113 LKH-114 LKH-122 LKH-123 LKH-124
Number of Stages 2 3 4 2 3 4
Flow rates for 50 Hz up to 75 m/h (330 US gall/min) and discharge pressures up to 40 bar (580 psig) with boost pressures up to 19 bar (275 psig) and for 60 Hz up to 80 m3/h (352 US gall/min) and boost pressures up to 26 bar (375 psig). For inlet pressures greater than 10 bar (145 psig) a special motor is used incorporating fixed angular contact bearings due to axial thrust. LKHP-High Pressure Range These pumps are designed to handle high inlet pressures built with reinforced pump casing and back plate. Application areas include reverse osmosis mono-filtration and ultra-filtration.
Fig. 4.1.4e LKHP-High Pressure
Fig. 4.1.4f LKHP-High Pressure (USA version) Alfa Laval Pump Handbook 49
Pump Description
The LKHP-High Pressure range is available in nine sizes, LKHP-10, -15, -20, -25, -35, -40, -45, -50 and -60. The pump range is designed for inlet pressures up to 40 bar (580 psig). Flow rates for 50 Hz up to 240 m/h (1056 US gall/min) with differential pressures up to 8 bar (115 psig). For 60 Hz, flow rates up to 275 m3/h (1210 US gall/min) with differential pressures up to 11 bar (160 psig). For these high inlet pressures a special motor with fixed angular contact bearings is used due to axial thrust. LKHSP Range The LKHSP self-priming pump is specially designed for pumping fluids containing air or gas without loosing its pumping ability. The pump is for use in food, chemical, pharmaceutical and other similar industries. These pumps can be used for tank emptying or as a CIP return pump where there is a risk of air or gas mixing with the fluid in the suction line. The pump is capable of creating a vacuum of 0.6 bar, depending upon pump size. The pump is supplied complete with a tank, a non-return valve (normally closed) on the inlet side, a tee and a non-return valve (normally open) on the bypass line. The LKHSP range is available in five sizes, LKHSP-10, -20, -25, -35 and -40. Flow rates up to 90 m/h (396 US gall/min) and differential pressures for 50 Hz up to 8 bar (115 psig) and for 60 Hz, 11 bar (160 psig). LKHI Range This pump range is similar to the LKH range but is suitable for inlet pressures up to 16 bar (230 psig). The pump can withstand this high inlet pressure due to being fitted with an internal shaft seal. The LKHI range is available in nine sizes, LKHI-10, -15, -20 ,-25, -35, -40, -50 and -60. Flow rates for 50 Hz up to 240 m/h (1056 US gall/min) with differential pressures up to 8 bar (115 psig). For 60 Hz, flow rates up to 275 m3/h (1210 US gall/min) with differential pressures up to 11 bar (160 psig).
Fig. 4.1.4g LKHSP
Pump Description
For inlet pressures greater than 10 bar (145 psig) a special motor is used incorporating fixed angular contact bearings due to axial thrust. LKH-UltraPure Range These pumps are designed for high purity applications such as water-for-injection (WFI). The pump is fully drainable supplied with associated pipework, fittings and valves. Another feature of this pump is self-venting, due to the pump casing outlet being turned 45.
Fig. 4.1.4h LKH-UltraPure
Fig. 4.1.4i LKH-UltraPure (USA version)
The LKH-UltraPure range is available in five sizes, LKH-UltraPure-10, -20, -25, -35 and -40. Flow rates up to 90 m/h (396 US gall/min) and differential pressures for 50 Hz up to 8 bar (115 psig) and for 60 Hz, 11 bar (160 psig). C Series range The C-Series is the original, all-purpose Alfa Laval centrifugal pump for less demanding applications. The range is designed for meeting sanitary requirements and can be Cleaned-In-Place. The C-series is produced mainly for the USA and is available in five sizes, C114, C216, C218, C328 and C4410. Flow rates for 60 Hz up to 227 m3/h (1000 US gall/min) and differential pressures up to 10 bar (145 psig).
Fig. 4.1.4j C-Series
Pump Description
4.2 Liquid Ring Pumps

4.2.1 General
The Alfa Laval range of Liquid Ring Pumps are specially designed for use in food, chemical and pharmaceutical industries where pumping liquids containing air or gases. As the liquid ring pump is self-priming when half filled with fluid, it is capable of pumping from a suction line partly filled with air or gases. As these pumps are self-priming, they are ideally used as return pumps in CIP systems. Attributes include: Self-priming (when pump casing is half filled with fluid). Suitable for aerated fluids. High efficiency. Minimal maintenance.

The liquid-ring pump is in principle a centrifugal pump. The pump is, however, self-priming when half filled with fluid. The self-priming capability is a result of the impeller design, small tolerances between the impeller and the pump casing, and due to a side channel made in the pump casing and/or the front cover. The discharge line should be routed 1 to 2 metres vertically upwards from the pump outlet connections to maintain the liquid ring in the side channels (see 12.5.1).
The sequence of a section between two impeller vanes during one revolution is described in the following: a) There is a certain fluid volume in the gap between the vanes which is not in contact with the channel.
a) to b) The gap is in contact with the channel, which gradually becomes deeper. Part of the fluid between the vanes fills the channel. The centrifugal force pushes the fluid outwards and consequently forms a vacuum at the centre of the impeller.
Pump Description
b) to c) The depth of the channel is still increased. The fluid volume is still forced outwards and consequently the fluid-free volume between the vanes is increased until it reaches a maximum where the channel has maximum depth. d) The vacuum created induces air from the suction line through the inlet at d.
d) to e) Air and fluid are circulated with the impeller until the depth of the channel begins to decrease. The volume between the vanes is gradually reduced as the depth of the channel is reduced and consequently pressure is built up at the centre of the impeller. e) The fluid is still forced outwards and the air remains at the centre of the impeller. The same volume of air that was induced through the inlet is now expelled through the outlet at e due to the pressure increase at the centre of the impeller.
e) to a) The section between the vanes will be refilled with fluid when it has passed the channel as only air and no fluid has yet been pumped. The cycle described above is continuously repeated as the impeller has several sections and rotates at approx. 1500 rev/min. (50 Hz) or 1800 rev/min. (60Hz). When all the air is removed from the suction line the described cycle is repeated for the fluid. The pump now operates as a fluid pump.
4.2.3 Design
As for centrifugal pumps, the liquid ring pump does not contain many parts the pumphead being connected to a standard electric motor. The impeller is fixed onto the pump shaft housed in a pump casing and casing cover. Impeller The impeller is of cast manufacture with straight radial impeller vanes. There is only one impeller size for each type of liquid ring pump.
Fig. 4.2.3a Impeller
Pump Description
Pump Casing and Casing Cover The pump casing is of cast manufacture complete with male screwed connections and fittings or clamp liners. The pump casing cover is also of cast manufacture, with or without a channel depending upon pump type/size. The pump casing and casing cover form the actual fluid chamber in which the fluid is transferred by means of the impeller.
Fig. 4.2.3b Pump with one channel
Fig. 4.2.3c Pump with two channels
Mechanical Seal The connection between the motor shaft/pump shaft and the pump casing is sealed by means of a mechanical seal, which is described in section 6. Shroud and Legs Pumps fitted with standard IEC motors utilise the shrouds and legs used on the LKH centrifugal pump range. Please note Alfa Laval Liquid Ring pumps for the USA market are supplied without shrouds.
Fig. 4.2.3d Pump with IEC standard motor
Pump Shaft/Connections Most pumps have stub shafts that are fixed to the motor shafts by means of compression couplings, as used on Centrifugal pumps. Adaptor For pumps fitted with a standard IEC electric motor, the connection between the motor and pump casing is made by means of an adaptor, similar to that used on Centrifugal pumps. (Adapter not used on MR-300 model).
Pump Description
4.2.4 Pump Range

The Alfa Laval Liquid Ring Pump range is designated the MR range. MR Range The MR range is available in four sizes, MR-166S, MR-185S, MR-200S and MR-300.
Fig. 4.2.4a MR-166S, MR-185S and MR-200S
Fig. 4.2.4b MR-300
Fig. 4.2.4c MR pump (USA version)
The pump range is designed for inlet pressures up to 4 bar (60 psig). Flow rates up to 80 m/h (350 US gall/min) and differential pressures of 5 bar (73 psig) for 50 Hz and 6 bar (87 psig) for 60 Hz.
Pump Description
4.3 Rotary Lobe Pumps

4.3.1 General
The Alfa Laval range of Rotary Lobe Pumps with its non-contact pump element design has the ability to cover a wide range of applications in industry. The hygienic design, anti-corrosive stainless steel construction and smooth pumping action have long established these pumps in the food, beverage, dairy and pharmaceutical industries. Attributes include: Gentle transfer of delicate suspended solids. Bi-directional operation. Compact size with high performance and low energy input. Ability to pump shear sensitive media. Easy maintenance.

Alfa Laval ranges of Rotary Lobe pumps are of conventional design operating with no internal contacting parts in the pump head. The pumping principle is explained with reference to the following diagram, which shows the displacement of fluid from pump inlet to outlet. The rotors are driven by a gear train in the pump gear gearbox providing accurate synchronisation or timing of the rotors. The rotors contra-rotate within the pump head carrying fluid through the pump, in the cavities formed between the dwell of the rotor and the interior of the rotorcase. In hydraulic terms, the motion of the counter rotating rotors creates a partial vacuum that allows atmospheric pressure or other external pressures to force fluid into the pump chamber. As the rotors rotate an expanding cavity is formed which is filled with fluid. As the rotors separate, each dwell forms a cavity. The meshing of the rotor causes a diminishing cavity with the fluid being displaced into the outlet port.
Pump Description
Horizontally ported pump (top shaft drive) 1 2 3 4
Vertically ported pump (left hand shaft drive) 1 2 3 4
4.3.3 Pump Range

Alfa Laval Rotary Lobe Pumps can be supplied bare shaft (without drive) or complete with drive such as electric motor, air motor, and diesel or petrol engine (see 8.2.7). Ranges primarily as follows: SRU Range The SRU pump range has been designed for use on general transfer duties throughout the brewing, dairy, food and chemical manufacturing processes. The SRU range is available in six series each having two pumphead displacements and two different shaft materials.
Fig. 4.3.3a SRU
Displacement is the theoretical amount of fluid the pump will transfer per revolution. Duplex stainless steel material used for higher pressures.
Pump Description
The SRU pump range incorporates a universally mounted gearbox on series 1 - 4. This gives the flexibility of mounting pumps with the inlet and outlet ports in either a vertical or horizontal plane by changing the foot and foot position. For the larger series 5 and 6, either horizontal or vertical plane inlet and outlet porting is achieved by using dedicated gearbox castings. This pump range also incorporates full bore through porting complying with international standards BS4825/ISO2037, maximising inlet and outlet port efficiency and NPSH characteristics. Flow rates up to 106 m/h (466 US gall/min) and pressures up to 20 bar (290 psig). The SRU range conforms to USA 3A requirements. Pump Nomenclature
SRU Series Build Selection SRU Model Displacement Differential Pressure Max. Speed
Pump head code
Gearbox
Shaft
Litres/ rev SRU1/005/LD or HD SRU1/008/LD or HD SRU2/013/LS SRU2/013/LD SRU2/018/LS SRU2/018/LD SRU3/027/LS SRU3/027/LD SRU3/038/LS SRU3/038/LD SRU4/055/LS SRU4/055/LD SRU4/079/LS SRU4/079/LD SRU5/116/LS SRU5/116/LD SRU5/168/LS SRU5/168/LD SRU6/260/LS SRU6/260/LD SRU6/353/LS SRU6/353/LD or or or or or or or or or or or or or or or or or or or or HS HD HS HD HS HD HS HD HS HD HS HD HS HD HS HD HS HD HS HD 0.053 0.085 0.128 0.128 0.181 0.181 0.266 0.266 0.384 0.384 0.554 0.554 0.79 0.79 1.16 1.16 1.68 1.68 2.60 2.60 3.53 3.53
UK gall/ 100 rev 1.17 1.87 2.82 2.82 3.98 3.98 5.85 5.85 8.45 8.45 12.19 12.19 17.38 17.38 25.52 25.52 36.95 36.95 57.20 57.20 77.65 77.65
US gall/ 100 rev 1.4 2.25 3.38 3.38 4.78 4.78 7.03 7.03 10.15 10.15 14.64 14.64 20.87 20.87 30.65 30.65 44.39 44.39 68.70 68.70 93.26 93.26
bar 8 5 10 15 7 10 10 15 7 10 10 20 7 15 10 20 7 15 10 20 7 15
psig 115 75 145 215 100 145 145 215 100 145 145 290 100 215 145 290 100 215 145 290 100 215
rev/min 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 600 600 600 600 500 500 500 500
1 2 3 4 5 6
L H S D
005 008 013 013 018 018 027 027 038 038 055 055 079 079 116 116 168 168 260 260 353 353
L or H L or H L L L L L L L L L L L L L L L L L L L L or or or or or or or or or or or or or or or or or or or or H H H H H H H H H H H H H H H H H H H H
D D S D S D S D S D S D S D S D S D S D S D
- Horizontal Porting - Vertical Porting - Stainless Steel - Duplex Stainless Steel Table 4.3.3a
Pump Description
Fig. 4.3.3b SX
SX Range The SX pump range is designed to be used where ultra-clean operation is critical, suited to applications in the pharmaceutical, biotechnology, fine chemical and speciality food industries. This pump range like the SRU range incorporates a universally mounted gearbox on series 1 - 4. This gives the flexibility of mounting pumps with the inlet and outlet ports in either a vertical or horizontal plane by changing the foot and foot position. For the larger series 5, 6 and 7, only vertical plane inlet and outlet porting is available by using a dedicated gearbox casting. This pump range also incorporates full bore through porting complying with international standards BS4825/ISO2037, maximising the inlet and outlet efficiency of the pump and the NPSH characteristics. The SX range has been certified by EHEDG (European Hygienic Equipment Design Group) as fully CIP cleanable to their protocol. In addition to being EHEDG compliant, the SX pump also conforms to the USA 3A standard and all media contacting components are FDA compliant. All media contacting elastomers are controlled compression joints to prevent pumped media leaking to atmosphere (see section 6.2). The SX range is available in seven series each having two pumphead displacements. Flow rates up to 115 m/h (506 US gall/min) and pressures up to 15 bar (215 psig).
Pump Nomenclature
SX Series Build Selection
Gearbox
SX Model
Displacement
Differential Pressure
Max. Speed
Pump head code
Litres/ rev SX1/005/H or U SX1/007/H or U SX2/013/H or U SX2/018/H or U SX3/027/H or U SX3/035/H or U SX4/046/H or U SX4/063/H or U SX5/082/H SX5/115/H SX6/140/H SX6/190/H SX7/250/H SX7/380/H 0.05 0.07 0.128 0.181 0.266 0.35 0.46 0.63 0.82 1.15 1.40 1.90 2.50 3.80
UK gall/ 100 rev 1.11 1.54 2.82 3.98 5.85 7.70 10.12 13.86 18.04 25.30 30.80 41.80 55.00 83.60
US gall/ 100 rev 1.32 1.85 3.38 4.78 7.03 9.25 12.15 16.65 21.67 30.38 36.99 50.20 66.05 100.40
bar 12 7 15 7 15 7 15 10 15 10 15 10 15 10
psig 175 100 215 100 215 100 215 145 215 145 215 145 215 145
rev/min 1400 1400 1000 1000 1000 1000 1000 1000 600 600 500 500 500 500
1 2 3 4 5 6 7
H U
005 007 013 018 027 035 046 063 082 115 140 190 250 380
H or U H or U H or U H or U H or U H or U H or U H or U H H H H H H
- Vertical Port (EHEDG approved) - Universal mounting (not EHEDG approved)
Table 4.3.3b
Pump Description
Pump Materials of Construction
5. Pump Materials of Construction

This section describes the materials, both metallic and elastomeric, that are used in the construction of Alfa Laval pump ranges.
5.1 Main Components

Pumps today can be manufactured from a number of different materials dependent upon the product being pumped and its environment. For Alfa Laval pump ranges this is generally stainless steel and can be split into two main categories: Product Wetted Parts (i.e. Metallic and elastomeric parts in contact with the fluid being pumped). Non-product Wetted Parts (i.e. Metallic and elastomeric parts not in contact with the fluid being pumped). Centrifugal and Liquid Ring Pumps
Main Pump Component Adaptor Backplate Impeller Pump Casing Pump Shaft Shroud and Legs Casing AISI 316L or Werkstoff 1.4404 AISI 316L or Werkstoff 1.4404 AISI 316L or Werkstoff 1.4404 AISI 316L or Werkstoff 1.4404 AISI 304 or Werkstoff 1.4301 Table 5.1a Product Wetted Parts Non-product Wetted Parts AISI 304 or Werkstoff 1.4301
Shroud Adaptor Fig. 5.1a Centrifugal pump Alfa Laval Pump Handbook 61
Rotary lobe pumps

Main Pump Component Metallic Product Wetted Parts SRU Models Metallic Non-product Wetted Parts BS EN 1561:1977 grade 250 cast iron Werkstoff 1.4404 or 316L, Non-galling alloy or rubber covered BS 3100:1991 316 C12 or 316L BS EN 10088-3:1995 grade 1.4404 or 316L BS3100:1991 316 C12 or 316L or BS EN10088-3:1995 grade 1.4404 BS3100:1991 316 C12 or 316L or BS EN10088-3:1995 grade 1.4404 Duplex stainless steel (AISI 329 or BS EN10088-3:1995 grade 1.4462) Metallic Product Wetted Parts SX Models Metallic Non-product Wetted Parts BS EN 1561:1977 grade 250 cast iron
Gearcase Rotor
Rotorcase
Rotorcase Cover
BS3100:1991 316 C12 or 316L or BS EN10088-3:1995 grade 1.4404 BS EN10088-3:1995 grade 1.4404 or 316L or duplex stainless steel (AISI 329 or BS EN10088-3:1995 grade 1.4462)
Shaft
Table 5.1b Product seal area Rotorcase Drive shaft
Gearbox Rotorcase cover Fig. 5.1b Rotary lobe pump Ports
For description of elastomers used see 5.3. For mechanical seal components see 6.1.
Surface finish of product wetted steel components has become a major factor in the food, pharmaceutical and biotechnology industries where hygiene and cleanability are of paramount importance.
5.2 Steel Surfaces

The standard machined surface finish on pumps can be enhanced by the following methods: Rumbling. Shot blasting. Electropolishing. Mechanical (Hand) polishing.
Rumbling This is achieved by vibrating the pump components with abrasive particulate such as stones and steel balls. Shotblasting This method involves blasting finished components with small metallic particles at great force to achieve the surface finish required. For Alfa Laval centrifugal stainless steel pump components, fine particles of stainless steel are used in this process to avoid contamination. Electropolishing This is an electro-chemical process in which the stainless steel component is immersed into a chemical bath and subjected to an electrical current. A controlled amount of metal is removed from all surfaces evenly. The appearance is Semi bright. Mechanical (Hand) polishing This is required when it is necessary to improve the surface finish beyond that achieved by electropolishing only i.e. a Mirror finish. It typically involves: Fine grinding using felt and compound. Brushing using bristle brushes and compound to remove any cutting marks left from fine grinding, and to reach any awkward areas. Polishing using mops and compound to obtain a mirror polished effect.
Surface Roughness The most commonly used surface roughness measurement is Ra and is defined as the arithmetic mean of the absolute value of the deviation of the profile from the mean line. Ra is measured in micron (m). The surface roughness can alternatively be specified by a Grit value. The Grit value specifies the grain size of the coating of the grinding tool used. The approximate connection between the Ra value and the Grit value is as follows: Ra = 0.8 m (32 Ra) 150 Grit (3A standard). Ra = 1.6 m (64 Ra) 100 Grit.
Fig. 5.2a Surface roughness
For Alfa Laval Centrifugal and Liquid Ring Pumps see table below:
Pump surfaces Standard surface roughness Ra (mm) by Rumbling method Optional surface roughness (3A finish) Ra (mm) by Mechanical (Hand) method Optional surface roughness (3A finish) Ra (mm) by shot blasting (Hand or Electropolished) < 0.5 (20 Ra) < 1.6 (64 Ra) 3.2 (125 Ra) 6.3 (250 Ra)
Product wetted surfaces External exposed surfaces Cast surfaces Other surfaces Table 5.2a
< 1.6 (64 Ra) < 1.6 (64 Ra) < 3.2 (125 Ra) 6.3 (250 Ra)
< 0.8 (32 Ra) < 1.6 (64 Ra) 3.2 (125 Ra) 6.3 (250 Ra)
Alfa Laval Centrifugal and Liquid Ring pumps supplied in the USA have all product wetted surfaces and external exposed surfaces to 0.8 Ra. For Alfa Laval Stainless Steel Rotary Lobe Pumps the surface roughness on product wetted parts such as rotors, rotorcase, rotor nuts and rotorcase covers is as follows: Standard 0.8 Ra Electropolishing 0.8 Ra Mechanical (Hand) 0.5 Ra
5.3 Elastomers
Alfa Laval pump ranges incorporate elastomers of different material and characteristics dependent upon application within the pump and the fluid being pumped. Various elastomer types are specified below. It is difficult to predict the lifetime of elastomers as they will be affected by many factors, e.g. chemical attack, temperature, mechanical wear etc. The temperature range limitations given below are dependent upon the fluid being pumped. To verify satisfactory operation at these limits please consult Alfa Laval.
A selection guide is shown in section 14.10.
NBR (Nitrile) Available as O-rings or Quad-rings (depending on pump type). Used as static or dynamic seals. Resistant to most hydrocarbons, e.g. oil and grease. Sufficiently resistant to diluted lye and diluted nitric acid. Temperature range - minus 40C min to 100C max. (minus 40oF to 212oF max.). Is attacked by ozone. EPDM (Ethylene Propylene) Available as O-rings or Quad-rings (depending on pump type). Used as static or dynamic seals. Resistant to most products used within the food industry. Resistant to ozone and radiation. Temperature range - minus 40C min to 150C max. (minus 40oF to 302oF max.). Not resistant to organic and non-organic oils and fats. FPM (Fluorinated rubber) - alternatively known as Viton Available as O-rings or Quad-rings (depending on pump type). Used as static or dynamic seals. Often used when other rubber qualities are unsuitable. Resistant to most chemicals and ozone. Temperature range - minus 20C min to 200C max. (minus 4oF to 392oF max.). Not suitable for fluids such as water, steam, lye, acid and alcohols being pumped hot.
PTFE (Polytetrafluoro Ethylene) Can be used as cover for O-ring seals of EPDM (i.e. encapsulated). Used as static or dynamic seals. Resistant to ozone. Resistant to almost all products. Temperature range - minus 30C min to 200C max. (minus 22oF to 392oF max.). Not elastic, tendency to compression set. MVQ (Silicone) Used as static or dynamic seals. Resistant to ozone, alcohols, glycols and most products used within food industry. Temperature range - minus 50C min to 230C max. (minus 58oF to 446oF max.). Not resistant to steam, inorganic acids, mineral oils, or most organic solvents. FEP (Fluorinated Ethylene Propylene) FEP covered (vulcanised) FPM or MVQ O-rings. Used as static or dynamic seals. Resistant to ozone. Resistant to almost all products. Suitable for temperatures up to approx. 200C (392oF). More elastic than PTFE covered EPDM. Kalrez (Perfluoroelastomer) Used as static or dynamic seals. Resistant to ozone. Resistant to almost all products. Temperature range minus 20C min to 250C max. (minus 4F to 482F max.). Elastic. Chemraz (Perfluroelastomer) Used as static or dynamic seals. Resistant to ozone. Resistant to almost all products. Temperature range minus 30C min to 250C max. (minus 22F to 482F max.). Elastic.
Pump sealing
6. Pump Sealing
This section describes the principle of pump sealing and illustrates the different sealing arrangements used on Alfa Laval pump ranges. A general seal selection guide is included, together with various operating parameters.
This section covers the shaft sealing devices used on Alfa Laval Centrifugal, Liquid Ring and Rotary Lobe Pumps. In addition to shaft seals, other proprietary seals not detailed in this section, such as o-rings and lip seals can be found on the pumphead and gearcase. A Pump is only as good as its shaft seal A successful pump application largely depends upon the selection and application of suitable fluid sealing devices. Just as we know that there is no single pump that can embrace the diverse range of fluids and applications whilst meeting individual market requirements and legislations, the same can be said of fluid sealing devices. This is clearly illustrated by the large range of shaft seal arrangements, both mechanical and packed gland, that are available to the pump manufacturer. Shaft sealing devices used in Alfa Laval Centrifugal, Liquid Ring and Rotary Lobe pumps include: Mechanical Seals (see 6.2). Single externally mounted. Single internally mounted. Single externally mounted for external flush. Single internally mounted for product recirculation or external flush. Double back to back with the inboard seal externally mounted for flush. Packed Glands (see 6.3). Both with and without lantern rings for flush.
Pump sealing
Centrifugal and Liquid Ring pumps only have one shaft seal whereas Rotary Lobe pumps employ a minimum of two shaft seals (one per shaft). Generally all shaft seals are under pressure with the pressure gradient across the seal being from pumped fluid to atmosphere. The exceptions will be single internally mounted or double seals where the product recirculation (single internally mounted only) or flush pressure is greater than the pump pressure, resulting in the pressure gradient being reversed. Mechanical seals meet the majority of application demands and of these, single and single flushed seals are most frequently specified. The application of double mechanical seals is increasing to meet both process demands for higher sanitary standards and legislation requirements, particularly those related to emissions. The majority of proprietary mechanical seals available from seal manufacturers have been designed for single shaft pump concepts, such as Centrifugal and Liquid Ring pumps. These pump types do not impose any radial or axial constraints on seal design. However on Rotary Lobe type pumps the need to minimise the shaft extension beyond the front bearing places significant axial constraints. If this were extended, the shaft diameter would increase introducing a radial constraint - because shafts on a rotary lobe pump are in the same plane, the maximum diameter of the seal must be less than the shaft centres. Most designs therefore can only accommodate bespoke or customised seal design. This is not done to take any commercial advantage but it is as a consequence of the rotary lobe pump design concept.
Pump sealing
There is often more than one solution and sometimes no ideal solution, therefore a compromise may have to be considered.
Selection of shaft seals is influenced by many variables: Shaft diameter and speed Fluid to be pumped Temperature Viscosity
Fluid behaviour
Solids
Thermal stability Air reacting Pressure
effect on materials? can interface film be maintained? drag on seal faces? clogging of seal restricting movement? can interface film be established and maintained? stiction at seal faces? does product shear, thin, thicken or work - balling/carbonise? can interface film be established and maintained? size? abrasiveness? density? clogging of seal restricting movement? can interface film be established and maintained? what, if any change? what, if any change? within seal limits? fluctuations? peaks/spikes? cavitation? flush? pressure? temperature? continuity? toxic? flammable? explosive? corrosive? irritant? carcinogenic?
Services
Health and Safety
Pump sealing
6.1 Mechanical Seals - General

Mechanical seals are designed for minimal leakage and represent the majority of Centrifugal, Liquid Ring and Rotary Lobe pump sealing arrangements. Mechanical seal selection must consider: The materials of seal construction, particularly the sealing faces and elastomers. The mounting attitude to provide the most favourable environment for the seal. The geometry within which it is to be mounted.
A mechanical seal typically comprises: A primary seal, comprising stationary and rotary seal rings. Two secondary seals, one for each of the stationary and rotary seal rings. A method of preventing the stationary seal ring from rotating. A method of keeping the stationary and rotary seal rings together when they are not hydraulically loaded i.e. when pump is stopped. A method of fixing and maintaining the working length.
The Primary Seal Comprises two flat faces, one rotating and one stationary, which support a fluid film, thus minimising heat generation and subsequent mechanical damage. Commonly used material combinations are: Carbon Carbon Carbon Silicon Carbide Tungsten Carbide Stainless Steel Silicon Carbide Tungsten Carbide Silicon Carbide Tungsten Carbide
Pump sealing
The Secondary Seal This is required to provide a seal between the primary seal rings and the components with which they interface. Also it can provide a cushion mounting for the seat ring to reduce any effects of mechanical stress i.e. shock loads. Types of secondary seal are: O-rings Cups Gaskets Wedges For Alfa Laval pump ranges the o-ring is the most common type of secondary seal used. Its simple and versatile concept is enhanced with the following comprehensive material options: NBR EPDM FPM PTFE MVQ FEP Kalrez Chemraz These are fully described in section 5.3. Mechanical Seal Face/O Ring Material Availability
Rotary Seal Face
Tungsten Carbide Stainless Steel Silicon Carbide
Stationary Seal Face

Tungsten Carbide Stainless Steel Silicon Carbide
Seal ORing
Pump Type
Pump Range
Carbon
Carbon
EPDM
PTFE
MVQ
FPM
NBR
Centrifugal/ Liquid ring
LKH LKH-Multistage LKHP-High Pressure LKHSP LKHI LKH-Ultra Pure MR SRU SX (see note)
! ! ! ! ! ! ! !
! ! ! ! ! ! ! ! !
! !
! !
! ! ! ! ! ! ! ! ! !
! ! ! ! ! ! !
! ! ! ! ! ! ! !
! ! ! ! ! ! ! ! ! ! !
! ! ! ! !
Rotary Lobe
Note: SX1 pump has tungsten carbide seal faces, not silicon carbide seal faces. Table 6.1a
Stationary Seal Ring Anti-Rotation Ideally the selected device listed below will also allow for axial resilience. Flats Pins Elastomer resilience Press fit Clamps Rotary Seal Ring Drive Ideally the selected device listed below will allow for a degree of axial movement. Spring Bellows Physical positioning Elastomer resilience
FEP
Pump sealing
One of the main causes of seal failure is for the seal working length not being correctly maintained.
Fig. 6.1a Typical single mechanical seal used in rotary lobe pumps
Working Length The ideal design should eliminate/minimise possibilities for error by incorporating: Physical position i.e. step on shaft Grub screws
7
Item 1 2 3 4 5 6 7
Working length
Description Stationary seal ring O-ring Stationary seal ring Rotary seal ring Rotary seal ring O-ring Wave spring Drive ring Grub screw
Fig. 6.1b Typical single mechanical seal used in centrifugal pumps

Drive ring
2 3
Impeller
Item 1 2 3 4 5
Pump shaft
Description Stationary seal ring Rotary seal ring Spring Stationary seal ring O-ring Rotary seal ring O-ring
Interface film
Aprox. 1 m Fig. 6.1c Principle of mechanical seal operation
Principle of Mechanical Seal Operation The function of the assembly is a combination of the extreme primary seal face flatness and applied spring force. Once the pump is operational, hydraulic fluid forces combine with seal design features i.e. balance, which push the seal faces together. This reduces the fluid interface thickness to a minimum whilst increasing pressure drop, therefore minimising pumped fluid leakage.
Pump sealing
Fig. 6.1d Principle of mechanical seal operation
Spring force Fluid pressure Stationary seal ring Rotating seal ring
The gap between the seal ring surfaces is enlarged to clarify the principle of mechanical sealing. Mechanical Seal Mounting Most mechanical seals can be mounted externally or internally. External Mechanical Seals The majority of mechanical seals used on Alfa Laval pump ranges are mounted externally, meaning that all the rotating parts of the mechanical seal (i.e. part of the rotary seal ring, spring, drive ring etc) are not in contact with the fluid to be pumped. The externally mounted mechanical seal is considered easy to clean, as only the inside of the stationary and rotary seal rings and their associated o-rings are in contact with the fluid being pumped. The R00 type mechanical seals used on the SX rotary lobe pump range, described in 6.2, are an exception to this, as it is the outside and not the inside of the seal components that is in contact with the fluid being pumped. Externally mounted seals have a lower pressure rating than the equivalent seal mounted internally.
Fig. 6.1e Typical external shaft seal
Rotating parts
Fluid
Pump sealing
Internal Mechanical Seals Some mechanical seals are mounted internally, meaning that most of the rotating parts are in contact with the fluid being pumped. The internal mechanical seal is designed with sufficient clearance around the rotating parts so that it can be cleaned as efficiently as possible and can withstand relatively high fluid pressures.
Fig. 6.1f Typical internal shaft seal
Rotating parts Fluid
For the Alfa Laval pump ranges, both the externally and internally mounted types of mechanical seal are available as single and single flushed versions. The externally mounted mechanical seal on Alfa Laval pump ranges is also available as a double flushed mechanical seal for some pump models. The typical single, single flushed and double flushed mechanical seal arrangements are described as follows: Single Mechanical Seal This is the simplest shaft seal version, which has already been described previously in this section. This seal arrangement is generally used for fluids that do not solidify or crystallise in contact with the atmosphere and other non-hazardous duties. For satisfactory operation it is imperative the seal is not subjected to pressures exceeding the maximum rated pressure of the pump. Also the pump must not be allowed to run dry, thus avoiding damage to the seal faces, which may cause excessive seal leakage. Typical applications are listed below, but full product/fluid and performance data must be referred to the seal supplier for verification. Alcohol Animal Fat Aviation Fuel Beer Dairy Creams Fish Oil Fruit Juice Liquid Egg Milk Shampoo Solvents Vegetable Oil Water Yoghurt
Pump sealing
Single Flushed Mechanical Seal The definition of flush is to provide a liquid barrier or support to the selected seal arrangement. This seal arrangement is generally used for any of the following conditions: where the fluid being pumped can coagulate, solidify or crystallise when in contact with the atmosphere. when cooling of the seals is necessary dependent upon the fluid pumping temperature.
This seal arrangement used on externally mounted seals requires the supply of liquid to the atmospheric side of the mechanical seal to flush the seal area. The characteristics of the fluid being pumped and the duty conditions will normally determine if a flush is necessary. When selecting a flushing liquid you must ensure that it is chemically compatible with the relevant materials of pump/seal construction and fully compatible with the fluid being pumped. Consideration should be given to any temperature limitations that may apply to the flushing liquid to ensure that hazards are not created (i.e. explosion, fire, etc). The flushing liquid is allowed to enter the seal housing at low pressure i.e. 0.5 bar max (7 psi max) to act as a barrier. This most basic flush system, sometimes referred to as quench, provides liquid to the atmosphere side of the mechanical seal thereby flushing away any product leakage. For the majority of pump models the flushed seal comprises the same stationary and rotating parts as the single seal, with the addition of a seal housing having a flushing connection and/or flushing tubes and a lip seal.
Fig. 6.1g Typical externally mounted single flushed mechanical seal used in rotary lobe pumps Item 1 2 3 4 5 6 7 8 9 10 11 12 Description Stationary seal ring O-ring Stationary seal ring Rotary seal ring Rotary seal ring O-ring Wave spring Drive ring Spacer O-ring Spacer Gasket Seal housing Lip seal Grub screw
12
Pump sealing
Fig. 6.1h Typical externally mounted single flushed mechanical seal used in centrifugal pumps
Item 1 2 3
Description Seal housing Lip seal Flushing tubes
Typical applications are listed below, but full product/fluid and performance data must be referred to the seal supplier for verification. Adhesive Caramel Detergent Fruit Juice Concentrate Gelatine Jam Latex Paint Sugar Syrup Toothpaste Yeast Double Flushed Mechanical Seal This seal arrangement is generally used with hostile media conditions i.e. high viscosity, fluid is hazardous or toxic. The double flushed seal used on Alfa Laval pump ranges is basically two single mechanical seals mounted back to back. This seal generally comprises the same stationary and rotating parts as the single seal for the majority of pump models, with the addition of a seal housing having a flushing connection and/or flushing tubes (dependent upon pump type). A compatible flushing liquid is pressurised into the seal housing at a pressure of 1 bar (14 psi) minimum above the discharge pressure of the pump. This results in the interface film being the flushing liquid and not the pumped liquid. Special attention is required in selecting seal faces and elastomers. The arrangement in contact with the pumped fluid is referred to as the inboard seal, and the seal employed for the flushing liquid is referred to as the outboard seal. For Alfa Laval Centrifugal pumps the design of the outboard seal differs to the inboard seal.
Fig. 6.1i Typical double flushed mechanical seal used in rotary lobe pumps
14
Rotorcase
Gearcase
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Description Stationary seal ring O-ring Stationary seal ring Rotary seal ring Rotary seal ring O-ring Wave spring Drive ring Wave spring Rotary seal ring O-ring Rotary seal ring Stationary seal ring Gasket Stationary seal ring O-ring Seal housing Grub screw
Pump sealing
Fig. 6.1j Typical double flushed mechanical seal used in centrifugal pumps
Item 1 2 3 4
Description Seal housing Flushing tubes Stationary seal ring Rotary seal ring
Typical applications are listed below, but full product/fluid and performance data must be referred to the seal supplier for verification. Abrasive Slurries Chocolate Glucose Hazardous Chemicals PVC Paste Photographic Emulsion Resin General Seal Face Operating Parameters Tables below show general parameters regarding viscosity and temperature, which should be noted when selecting a mechanical seal.
Table 6.1b Viscosity up to 4999 cP Seal Face Combination Solid Carbon v Stainless Steel Solid Carbon v Silicon Carbide Solid Carbon v Tungsten Carbide Inserted Carbon v Stainless Steel Inserted Carbon v Silicon Carbide Inserted Carbon v Tungsten Carbide Silicon Carbide v Silicon Carbide Tungsten Carbide v Tungsten Carbide Consider Double Seals
up to 24999 cP
up to 149999 cP above 150000 cP
Table 6.1c
Temperature up to 150C (302 F)

o
Seal Face Combination Inserted Carbon v Stainless Steel Inserted Carbon v Silicon Carbide Inserted Carbon v Tungsten Carbide Silicon Carbide v Silicon Carbide Tungsten Carbide v Tungsten Carbide Solid Carbon v Stainless Steel Inserted Carbon v Silicon Carbide Inserted Carbon v Tungsten Carbide
up to 200C (392oF)
Pump sealing
Flushing Pipework Layout The suggested arrangement below is for single mechanical seals only. If the pump is fitted with double mechanical seals or packed glands the pressure gauges and control valves should be fitted on the outlet side of the system. The choice of flushing liquid is dependent upon compatibility with the pumping media and overall duty conditions i.e. pressure and temperature. Usually water is used for cooling and any water soluble products.
Fig. 6.1k Typical flushing pipework layout for a rotary lobe pump *Pressure gauge *Control valve Pressure gauge Control valve Suggested visible indication of flow * Double mechanical seal only
Flush inlet Check valve Isolation valve
Flush outlet to waste
Fig. 6.1l Typical flushing pipework layout for a centrifugal pump
Free outlet
Inlet
Pump sealing
Mechanical Seal Selection Process The illustration below describes the mechanical seal selection process with relevant questions to be answered.
Fig. 6.1m Seal selection process
Obtain all Product/Fluid and Performance data
This should be used for guidance purposes only, as actual seal selections should be verified by the seal suppliers.
Select Seal Type
Does fluid crystallise? Is cooling required? Will pump run dry? Is aseptic barrier required?
Yes
Use Single Flushed Seal
No
Is fluid hazardous? Is fluid abrasive? Is fluid viscosity high? Is temperature high? Is aseptic barrier required?
Yes
Use Double Flushed Seal
No
Use Single Seal
Select Seal Materials
Select Seal Faces
Select Elastomers
- Check viscosity limitations (see table 6.1b). - Check temperature limitations (see table 6.1c). - Is fluid abrasive? - Check chemical compatibility.
- Check elastomer compatibility (see guide in section 14.10). - Check temperature limitations.
Pump sealing
6.2 Mechanical Seal Types in Alfa Laval Pump Ranges

Seal Option Availability for Centrifugal and Liquid Ring Pumps
Pump Range Single LKH LKH-Multistage LKHP LKHSP LKHI LKH-UltraPure MR-166S, -200S MR-300 Table 6.2a ! ! ! ! ! ! ! ! ! ! External Mounting Single Flushed ! Double Flushed ! ! ! ! ! Internal Mounting Single Single Flushed
Seal Option Availability for Rotary Lobe Pumps

Table 6.2b Mechanical Seal Type Seal Name Pump Range SRU SX ! ! ! ! ! ! ! ! !
Single externally mounted
R90 R00 Hyclean R90 R00 Hyclean R90 R90 R00
Single flushed externally mounted
Single flushed internally mounted Double flushed
R90 Type Mechanical Seals The basic working principles of the R90 type mechanical seals have previously been referred to in 6.1. Hyclean Type Mechanical Seals This seal arrangement is generally used for food and other hygienic applications. The design of this seal incorporates a self-cleaning feature.
Pump sealing
Fig. 6.2a Hyclean single mechanical seal

7
Item 1 2 3 4 5 6 7
Description Rotorcase O-ring Wave Spring Shaft O-ring Stationary Seal Ring Rotary Seal Ring Washer Clip
Front cover compression joint
Cup seal
Spline sealing cup seal
Squad ring
Fig. 6.2b SX pumphead sealing Fig. 6.2c R00 single mechanical seal
R00 Type Mechanical Seals The R00 type mechanical seals specifically designed for the SX rotary lobe pump range are fully front loading seals and fully interchangeable without the need for additional housings or pump component changes. Specialised seal setting of the mechanical seal is not required as the seal is dimensionally set on assembly. Seal faces positioned in the fluid area minimise shear forces. All seals have controlled compression joint elastomers at fluid/atmosphere interfaces.
1 2
3 4
Item 1 2 3 4 5
Description Wave Spring Squad Ring Rotary Seal Ring Cup Seal Stationary Seal Ring
Pump sealing
6.3 Other Sealing Options (Rotary Lobe Pumps only)

This is a simple, low cost, and easy to maintain controlled leakage sealing arrangement. These are specified for many dirty applications, but when possible, should always be avoided for sanitary duties, as they are less hygienic than mechanical seals. Packed Gland The grade of packing used depends on the product being handled and operating conditions. When packed glands are specified, using polyamide or PTFE packings will satisfy the majority of duties. Provided the liquid being sealed contains no abrasive particles or does not crystallise, gland packings will function satisfactorily on plain stainless steel shafts or renewable stainless steel shaft sleeves. In instances of moderately abrasive fluids, such as brine solutions being handled, the pumps should be fitted with hard coated shaft sleeves, which may be easily replaced when worn. Pumps provided with a packed gland seal are normally fitted with rubber slingers mounted between the gland followers and the gearcase front lip seals. The slingers will reduce the possibility of the product contacting the gearcase lip seals, thereby overcoming any undesirable operating conditions that could arise in this area. When correctly assembled and adjusted, a slight loss of product should occur so as to lubricate the packing and shaft or sleeve, if fitted.
9
Fig. 6.3a Packed gland Item 1 2 3 4 5 6 7 8 9 Description Shaft sleeve O-ring Shaft sleeve Spacer Packing rings Gasket Gland housing Gland follower Ring slinger Grub screw
This seal arrangement is available on all SRU pump models. Packed Gland with Lantern Ring With fluids containing very abrasive particles or fluids that will coagulate, solidify or crystallise in contact with the atmosphere, a packed gland with lantern ring may be used. In such circumstances a compatible liquid is supplied to the chamber formed by the lantern ring at a pressure of at least 1 bar (14 psi) above the pump pressure. The function of this liquid is to prevent, or at least inhibit, the entry of abrasives into the very small clearances between the shaft and packing. In the case of liquids which coagulate, solidify or crystallise in contact with the atmosphere the flushing liquid acts as a dilutant and barrier in the gland area preventing the pumped fluid from coming in contact with the atmosphere.
Pump sealing
A disadvantage with this seal arrangement is that the flushing liquid will pass into the product causing a relatively small degree of dilution/ contamination, which cannot always be accepted. In common with all packed gland assemblies slight leakage must occur but in this instance it will basically be a loss of flushing liquid as opposed to product being pumped.
Fig. 6.3b Packed gland with lantern ring
10
Item 1 2 3 4 5 6 7 8 9 10
Description Shaft sleeve O-ring Shaft sleeve Spacer Packing rings Lantern ring Gasket Gland housing Gland follower Ring slinger Grub screw
This seal arrangement is available on all SRU pump models.
Pump sealing
Pump Sizing
7. Pump Sizing
This section shows how to size an Alfa Laval pump from product/ fluid and performance data given, supported by relevant calculations and worked examples with a simple step by step approach.
7.1 General Information Required

In order to correctly size any type of pump some essential information is required as follows: See section 2 for detailed descriptions of Product/Fluid data and Performance data. Product/Fluid Data Fluid to be pumped. Viscosity. SG/Density. Pumping temperature. Vapour pressure. Solids content (max. size and concentration). Fluid behaviour (i.e. Newtonian or Pseudoplastic etc.). Is product hazardous or toxic? Does fluid crystallise in contact with atmosphere? Is CIP required? Performance Data Capacity (Flow rate). Discharge head/pressure. Suction condition (flooded or suction lift). Site Services Data Power source (electric, air, diesel, petrol or hydraulic). If electric - motor enclosure and electrical supply. Seal flushing fluid. In an ideal situation all the above criteria should be known before sizing a pump - however, in many instances not all of this information is known and made available. In such cases to complete the sizing process, some assumptions may need to be made based upon application knowledge, experience etc. These should be subsequently confirmed, as they could be critical to satisfactory installation and operation.
Pump Sizing
7.2 Power
All of the system energy requirements and the energy losses in the pump must be supplied by a prime mover in the form of mechanical energy. The rate of energy input needed is defined as power and is expressed in watts (W) - for practical purposes, power within this handbook is expressed in kilowatts (kW), i.e. watts x 10.
7.2.1 Hydraulic Power

The theoretical energy required to pump a given quantity of fluid against a given total head is known as hydraulic power, hydraulic horse power or water horse power. This can be calculated as follows: Hydraulic Power (W) = Q x H x x g where: Q H g = = = = capacity (m3/s) total head/pressure (m) fluid density (kg/m) acceleration due to gravity (m/s2)
Other forms of this equation can be as follows: Hydraulic Power (kW) = Q x H k where: Q = capacity H = total head/pressure k = constant (dependent upon units used)
Therefore Hydraulic Power (kW) = Q x H k where: Q = capacity (l/min) H = total head/pressure (bar) k = 600
Pump Sizing
or
Hydraulic Power (hp) = Q x H k where: Q = capacity (US gall/min) H = total head/pressure (psi) k = 1715
or
Hydraulic Power (hp) = Q x H k where: Q = capacity (UK gall/min) H = total head/pressure (psi) k = 1428
7.2.2 Required Power

r = radius
The required power or brake horsepower is the power needed at the pump shaft. This is always higher than the hydraulic power due to energy losses in the pump mechanism (friction loss, pressure loss, seals etc) and is derived from: Required Power = xT where: = shaft angular velocity T = Shaft Torque Shaft angular velocity = V x r And is related to Hydraulic power by: Required Power = Hydraulic Power Efficiency (100% = 1.0)
V= velocity
Fig. 7.2.2a Shaft angular viscosity
The appropriate prime mover power must be selected. Generally this will be the nearest prime mover rated output power above the required power.
Pump Sizing
The power requirements for mechanical devices such as pumps and pump drives are best expressed in terms of torque and speed.
7.2.3 Torque
Torque is defined as the moment of force required to produce rotation and is usually expressed in units of Nm (Newton metres), Kgfm (Kilogram metres) or ftlb (foot pounds). Torque can be calculated as follows: Torque (Nm) = Required power (kW) x 9550 Pump speed (rev/min)
or Torque (Kgfm) = Required power (kW) x 974 Pump speed (rev/min) or
Torque (ftlb)
= Required power (hp) x 5250 Pump speed (rev/min)
It should be noted that rotary lobe pumps are basically constant torque machines and therefore it is important that the transmission chosen is capable of transmitting the torque required by the pump. This is particularly important for variable speed drives which should be selected initially on torque rather than power.
7.2.4 Efficiency
Total Efficiency Total efficiency is typically used on centrifugal and liquid ring pumps to describe the relationship between input power at the pump shaft and output power in the form of water horsepower. The term mechanical efficiency can also be used to describe this ratio. Total efficiency, designated by symbol , comprises of three elements, Hydraulic Efficiency (h), Mechanical Efficiency (m ) and Volumetric Efficiency (v ) which are described below: Hydraulic Efficiency The term hydraulic efficiency is used on centrifugal and liquid ring type pumps to describe one of the three elements of centrifugal and liquid ring pump total efficiency as described above. where Hydraulic Efficiency (h)= Pump head loss (m) x 100% Total head (m)
The pump head losses comprise of the shock loss at the eye of the impeller, friction loss in the impeller blade and circulation loss at the outlet side of the impeller blades.
Pump Sizing
Mechanical Efficiency This term is used on all centrifugal, liquid ring and rotary lobe pump types, and is typically used to describe the losses associated with the transfer of energy from the prime mover through a mechanical system to the pumped liquid. where Mechanical Efficiency (m ) = 1 Pump mechanical losses x 100% Required power Pump mechanical losses refers to the friction losses associated with bearings, seals and other contacting areas within the pump. Volumetric Efficiency This term is used on all centrifugal, liquid ring and rotary lobe pump types. It is most commonly used to compare the performance of a number of pump types, where accurate geometric data is available. For centrifugal and liquid ring pumps, Volumetric Efficiency (v) = Q x 100% Q + QL
where:
Q = Pump capacity. Q L = Fluid losses due to leakage through the impeller casing clearances.
For rotary lobe pumps the term volumetric efficiency (v) is used to compare the displacement of the pump against the capacity of the pump. The displacement calculation (q) per revolution for rotary lobe pumps involves calculating the volume of the void formed between the rotating element and the fixed element of the pump. This is then multiplied by the number of voids formed by a rotating element per revolution of the pumps drive shaft and by the number of rotors in the pump. For rotary lobe pumps, Volumetric Efficiency (v) = Q x 100% q where: Q = Pump capacity. q = Pump displacement.
Pump Sizing
Rotary lobe pumps are generally highly efficient and even at viscosity of 100 cP the volumetric efficiency of most pumps is approximately 90% for low pressure duties. At lower viscosities and/or higher pressures the volumetric efficiency will decrease due to slip as described in 8.6.1. Above 1000 cP, volumetric efficiency can be as high as 95 - 99%. For these high viscosity duties, to select a pump speed the following formulas can be used as a general guide. n = Q x 100 q x v x 60 where n Q q v = pump speed (rev/min) = capacity (m/h) = pump displacement (m/100 rev) = vol. efficiency (100% = 1.0)
or
n = Q x 100 q x v
where n Q q v
= pump speed (rev/min) = capacity (US gall/min) = pump displacement (US gall/100 rev) = vol. efficiency (100% = 1.0)
or
n = Q x 100 q x v
where n Q q v
= pump speed (rev/min) = capacity (UK gall/min) = pump displacement (UK gall/100 rev) = vol. efficiency (100% = 1.0)
Pump Efficiency The term pump efficiency is used on all types of pumps to describe the ratio of power supply to the drive shaft against water horsepower. Pump Efficiency p
= Water horse power x 100% Required power
or Pump Efficiency p
= QxHxxg xT
where:
Q H g T
= capacity (m/s) = total head/pressure (m) = fluid density (kg/m) = acceleration due to gravity (m/s) = shaft angular velocity (rad/s) = shaft torque (Nm)
Pump Sizing
Overall Efficiency Overall efficiency is a term used to describe and compare the performance of all types of pump. Overall efficiency considers the efficiency of both the prime mover and the pump, and is sometimes known as the wire to water/liquid efficiency where the prime mover is an electric motor. Overall Efficiency oa = Water horse power x 100% Drive power
Pump Sizing
7.3 Centrifugal and Liquid Ring Pumps

In general the theory regarding sizing of centrifugal and liquid ring pumps is similar.
7.3.1 Flow Curve

A centrifugal or liquid ring pump should always be sized from a pump flow curve or a pump selection program. Most pump flow curves are based on tests with water. It is difficult to determine general curves for fluids with viscosities different from water and therefore in these instances it is recommended to use a pump selection program. A pump flow curve specifies the connection between capacity Q , head H , required power P , required NPSH and efficiency . Hydraulic Losses The connection between the capacity and the theoretical head of the pump is shown by means of a straight line, which decreases at a higher capacity (see fig. 7.3.1a). The actual head of a pump is, however, lower than the theoretical head due to hydraulic losses in the pump, which are friction loss, pressure loss and slip.
Fig. 7.3.1a Hydraulic losses
The connection between the capacity and actual head is consequently specified by means of a curve which varies depending on the design of the impeller. Different Pump Characteristics The capacity Q and head H curve of a centrifugal pump will vary depending upon the impeller vane design (see fig. 7.3.1.b). These fulfil different requirements and are well suited for flow control where only one parameter is to be changed (see 7.3.2). Curve 1 covers a wide range of heads without large changes to capacity. Curve 3 covers a wide range of capacities without large changes to head.
Fig. 7.3.1b Curves for Q and H
Pump Sizing
Curves for Capacity Q, Head H, Power P and Efficiency In principle the duty point of a pump can be situated at any point on the Q-H curve. The efficiency of the pump will vary depending on where the duty point is situated on the Q-H curve. The efficiency is usually highest near the centre of the curve.
Fig. 7.3.1c Curves for Q, H, P and
The power curve of the centrifugal pump increases at a higher capacity. The power curve of the liquid ring pump decreases at a higher capacity. NPSHr Curve The NPSHr curve increases at higher capacity (see fig. 7.3.1d). This should be used to assertain the NPSHr of the pump. It is important that NPSHa of the system exceeds the NPSHr of the pump.
Fig. 7.3.1d NPSHr curve
Viscosity Effect Fluid viscosity will affect capacity, head, efficiency and power (see fig. 7.3.1e). Capacity, head and efficiency will decrease at higher viscosities. Required power will increase at higher viscosities.
Fig. 7.3.1e Effects on Q, H and
Density Effect Fluid density will affect the head and required power which both increase proportionally at higher density (see fig. 7.3.1f).
Fig. 7.3.1f Effects on Q, H and
Pump Sizing
How to use the Flow Curve The flow curve consists of three different curves: Head as a function of capacity (Q - H curve). Required power as a function of capacity (Q - P curve). Required NPSH as a function of capacity (Q - NPSHr curve). Although illustrated here the efficiency is not shown on the published flow curves but can be determined from the required power on the flow curve and formula in 7.2 when the duty point is known. The Q - H and Q - P curves are specified for different standard impeller diameters so that a correct duty point can be determined. This is not applicable to the Liquid Ring pumps as the impeller diameters cannot be reduced. The curves on the flow curve are based on tests with water at 20C (68oF) with tolerances of + 5%. It is recommended to select the pump by means of a pump selection program if the fluid to be pumped has other physical properties. Example: Product/Fluid Data: Fluid to be pumped Viscosity SG Pumping temperature Performance Data: Capacity Total head Electrical supply -
Water. 1 cP. 1.0 20C.
15 m/h. 25 m. 220/380v, 50Hz.
The optimum is to select the smallest pump possible which is suitable for the required duty point (15 m/h, 25 m).
Pump Sizing
Step 1 - Find Appropriate Curve Locate a flow curve for the required pump type that covers the duty point. For this particular example a flow curve of a centrifugal pump type LKH-10 with 3000 rev/min synchronous speed at 50Hz is selected.
Fig. 7.3.1g Example
28
Step 2 - Look at Q - H curve Locate the capacity (15 m/h) on the Q-scale. Start from this point and follow the vertical line upwards until it intersects with the horizontal line indicating the required head (25 m) on the H-scale. This duty point does not contact any curve corresponding to a certain impeller diameter. Therefore, the nearest larger size impeller diameter should be selected, in this case 150 mm. The head will then be 28 m. The selected head (28 m) should be checked regarding the lower tolerance of the curve to ensure that it is at least the required 25 m. In this case the head should be reduced by 5% being the curve tolerance. The head will then be a minimum of 26.6 m greater than 25 m, thus satisfactory.
Pump Sizing
Step 3 - Look at Q - P curve The next step in selecting the pump is to follow the vertical capacity line (15 m/h) downwards until it intersects with the power curve for the 150 mm impeller. A horizontal line to the left of the intersection indicates a required power of 2.0 kW. For a LKH centrifugal pump a safety factor of 5% for motor losses must be added, resulting in a total required power of 2.1 kW. Consequently a 2.2 kW motor can be used. Step 4 - Look at Q - NPSHr curve Finally the vertical capacity line (15 m/h) is followed up to the NPSHr curve. The intersection corresponding to the 150 mm impeller is located. A horizontal line to the right of the intersection indicates that NPSHr is approx. 0.8 m.
7.3.2 Flow Control

Duty Point The duty point of a pump is the intersection point between the pump curve and the process curve. Pump curve - this specifies the connection between head H and capacity Q (see 7.3.1). Process curve - this specifies the connection between the total Q ) (see fig. pressure drop (H ) in the process plant and the capacity (Q 7.3.2a). The process curve is determined by varying the capacity so that different pressure drop (H) values are obtained. The shape of the process curve will depend on the process design (i.e. layout, valves, filters etc.). Capacity: Pressure drop: Q1 DH1 Q2 DH2 Q3 DH3 Q4 DH4 Q5 DH5 Q6 DH6
The duty point of a pump can change due to changes in the conditions of the process plant (changes in head, pressure drops etc.). The pump will automatically regulate the capacity to meet the new conditions (see fig. 7.3.2b and 7.3.2c).
Fig. 7.3.2a Process curve
Pump Sizing
Fig. 7.3.2b Changes in pressure drop
Fig. 7.3.2c Changes in required head
It is possible to compensate for the change of duty point by means of flow control that can be achieved as follows: Reducing the impeller diameter (not for liquid ring pumps). Throttling the discharge line. Controlling the pump speed. Due to flow control it is possible to achieve optimum pump efficiency at the required capacity resulting in the most economical pump installation. Reducing Impeller Diameter Reducing the impeller diameter can only be carried out for centrifugal pumps and multi-stage centrifugal pumps. This will reduce the capacity and the head. Centrifugal Pump D ), capacity (Q Q ) and head The connection between impeller diameter (D H ) is shown in fig. 7.3.2d: (H
Fig. 7.3.2d Reducing impeller diameter
1. Before reducing. 2. After reducing - the duty point moves towards point 2 when reducing the impeller diameter.
Pump Sizing
If the impeller speed remains unchanged, the connection between D ), capacity (Q Q ), head (H H ) and required power (P P ) is impeller diameter (D shown by the following formulas:
Diameter/capacity:
Q1 Q2
D13 D
3 2
D2 = D1 x
Q [mm]
3
Q2
1
Diameter/head:
H1 H2
D12 D
2 2
D2 = D1 x
H
5
H2
1
[mm]
Diameter/power:
P1 P2
D15 D25
D2 = D1 x
H [mm]
H2
1
Most pump flow curves show characteristics for different impeller diameters to enable the correct impeller diameter to be selected. Reducing the impeller diameter by up to 20% will not affect the efficiency of the pump. If the reduction in impeller diameter exceeds 20%, the pump efficiency will decrease. Multi-stage Centrifugal Pump This pump has several impellers depending upon pump type. The total head can be adjusted by reducing the diameter of the back impeller, which is situated at the pump outlet (nearest to the back plate). Consequently the exact duty point will be between the curves of two pump sizes. D ), capacity (Q Q ), head (H H) The connection between impeller diameter (D and type of pump is shown in fig. 7.3.2e.
c b
Fig. 7.3.2e Reducing impeller diameter
Pump Sizing
The formula is for guidance purposes only. It is, therefore, recommended to add a safety factor of 10-15% to the new diameter.
The impeller diameter is reduced to D2 by means of the following formula:
D2 = D1 x
a-b [mm]
c-b
Where: D1 = Standard diameter before reducing. a = Max. duty point. b = Min. duty point. c = Required duty point. Throttling Discharge Line Throttling the discharge line will increase the resistance in the process plant, which will increase the head and reduce the capacity. The Q ) and head (H H ) when throttling is connection between capacity (Q shown in fig. 7.3.2f. 1. Before throttling. 2. After throttling, the duty point moves towards point 2.
Fig. 7.3.2f Throttling discharge line
Throttling should not be carried out in the suction line as cavitation can occur. Also throttling will reduce the efficiency of the process plant H shows the waste of pressure at point 2. Controlling Pump Speed Changing the impeller speed will change the centrifugal force created by the impeller. Therefore, the capacity and the head will also change. Q ) and head (H H ) when changing The connection between capacity (Q the impeller speed is shown in fig. 7.3.2g. 1. Before reducing impeller speed. 2. After reducing impeller speed. The working point moves towards point 2 when reducing the impeller speed.
Fig. 7.3.2g Controlling pump speed
Pump Sizing
The most common form of speed control is by means of a frequency converter (see 9.10).
If the impeller dimensions remain unchanged, the connection between n ), capacity (Q Q ), head (H H ) and required power (P P ) is impeller speed (n shown by the following formulas:
Speed/capacity:
Q1 Q2
n1 n2
n2 = n1 x
Q2 Q1
[rev/min]
Speed/head:
H1 H2
n12 n
2 2
n2 = n1 x
H P
3
H2
1
[rev/min]
Speed/power:
P1 P2
n13 n
3 2
n2 = n1 x
P2
1
[rev/min]
As shown from the above formulas the impeller speed affects capacity, head and required power as follows: Half speed results in capacity x 0.5. Half speed results in head x 0.25. Half speed results in required power x 0.125. Speed control will not affect the efficiency providing changes do not exceed 20%.
7.3.3 Alternative Pump Installations

Pumps Coupled in Series It is possible to increase the head in a pump installation by two or more pumps being coupled in series. Q ) will always be constant throughout the pump series. The capacity (Q The head can vary depending on the pump sizes.
Fig. 7.3.3a Principle of connection
The outlet of pump 1 is connected to the inlet of pump 2. Pump 2 must be able to withstand the outlet head from pump 1.
Pump Sizing
If two different pumps are connected in series, the pump with the lowest NPSH value should be installed as the first pump (for critical suction conditions). It is important that pumps installed in series are connected with the largest pump before the smallest. Otherwise the second pump will overrule the first pump, causing unstable operation and cavitation. Adjustment of head by reducing the impeller diameter must always be on the second pump. A multi-stage centrifugal pump is in principle several pumps that are coupled in series but built together as one pump unit. Pumps Coupled in Parallel It is possible to increase the capacity in a pump installation by two or more pumps coupled in parallel.
Fig. 7.3.3b Head of pumps in series
Fig. 7.3.3c Principle of connection
Fig. 7.3.3d Connection of two similar pumps
Fig. 7.3.3e Connection of two different pumps
The head (H) will always be constant in the pump installation. The capacity can vary depending on the pump sizes. The pumps receive the fluid from the same source and have a common discharge line. When the capacity is increased by means of pumps coupled in parallel, the equipment and pressure drop in the installation must be determined according to the total capacity of the pumps. For two different pumps, If the capacity Q1 is smaller than the capacity Q2, it is possible to install a non-return valve in the discharge line of pump 1 to avoid pump 2 pumping fluid back through pump 1.
Fig. 7.3.3f Connection of two different pump sizes
Pump Sizing
7.4 Worked Examples of Centrifugal Pump Sizing (Metric units)

7.4.1 Example 1
The following example shows a pump to be sized for a typical brewery process. The pump is required to handle Wort from the Whirlpool to the Fermentation vessel.
Yeast CIP CO2 CO2 Fermentation
CIP CO2 CO2 0.6 bar (pressure vessel)
Cooling
21 m
O2 Wort pump Yeast pitching Whirlpool
80 m
Fig. 7.4.1a Example 1
As described in 7.1 in order to correctly size any type of pump, some essential information is required such as Product/Fluid data, Performance data and Site Services data.
Pump Sizing
All the data have been given by the customer.
Product/Fluid data: Fluid to be pumped Viscosity Pumping temperature Performance data: Capacity Discharge -
Wort. 1 cP. 90C.
Suction
40 m/h. via 80 m of 101.6 mm dia. tube, plus a given number of bends, valves and a plate heat exchanger with pPHE 1.6 bar. Static head in Fermenting vessel = 21 m. Pressure in Fermenting vessel = 0.6 bar. 0.4 m head, plus a given number of bends and valves.
Site Services data: Electrical supply -
220/380v, 50 Hz.
Before sizing a pump, it will be necessary to determine the total head and NPSHa. The theory, including the different formulae regarding these parameters is more specifically described in 2.2.2 and 2.2.4.
Total head
Total discharge head Ht = ht +hft +pt Where ht = Static head in Fermentation vessel. hft = Total pressure drop in discharge line. pt = Pressure in Fermentation vessel. Therefore
Fig. 7.4.1b
ht = 21 m. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p + Pressure drop in plate heat exchanger pPHE ptube from curve shown in 14.5 = 2 m. p is calculated to be 5 m. pPHE is given as 1.6 bar = 16 m. hft = 2 + 5 + 16 m. = 23 m. pt = 0.6 bar = 6 m.
Ht = ht +hft +pt = 21 + 23 + 6 m = 50 m (5 bar).
Pump Sizing
Total suction head Hs = hs hfs +ps Where hs = Static suction head in Whirlpool. hfs = Total pressure drop in suction line. ps = Pressure in Whirlpool (open tank). Therefore hs = 0.4 m. hfs = calculated to be 1 m. ps = 0 (open tank).
Hs = hs hfs +ps = 0.4 1 + 0 m = 0.6 m ( 0.06 bar). Total head H = Ht Hs = 50 ( 0.6) = 50.6 m 51 m (5.1 bar).
NPSHa
NPSHa = Pa + hs hfs Pvp Where Pa = Pressure absolute above level of fluid in Whirlpool tank. hs = Static suction head in Whirlpool tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 1 bar (open tank) = 10 m. 0.4 m. Calculated to be 1 m. 0.70 bar a (from table 14.4a) = 7 m.
NPSHa = 10 + 0.4 1 7 (m) = 2.4 m. Actual pump sizing can be made using pump performance curves or a pump selection program. The performance curves are, however, not suitable if the fluid to be pumped has physical properties (i.e. viscosity) different from water. In this particular example both the pump performance curves and pump selection program can be used. The performance curve selection procedure is more specifically described in 7.3.1. For this particular example, pump sized would be as follows: Pump model Impeller size Speed Capacity Head Efficiency NPSHr Motor size LKH-25. 202 mm. 2930 rev/min. 40 m/h. 51.5 m (5.15 bar). 63.1%. 1.4 m. 11 kW.
Pump Sizing
Cavitation check: NPSHa should be greater than NPSHr i.e. 2.4 m > 1.4 m, i.e. no cavitation will occur. The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a double mechanical seal with carbon/silicon carbide faces and EPDM elastomers.
1: Full vessel 2: Empty vessel ht1 1 2
ht2
Q2 Fig. 7.4.1c
Special Note The discharge head (ht2) is lower when the pump starts filling the fermenting vessel compared to the discharge head (ht1) when the vessel is full. The reduction of the discharge head can result in cavitation and overloading of the motor due to a capacity increase. Cavitation can be avoided by reducing the pump speed (reducing NPSHr), i.e. by means of a frequency converter, or by throttling the discharge line (increasing head). The flow control method is more specifically described in 7.3.2. Adjustment In this example the pump is sized by the pump selection program which results in exact impeller diameter of 202 mm, so that the selected duty point is as close to the required duty point as possible. The pump is sized with a standard impeller diameter if using the performance curve. In this case it may be necessary to adjust the selected duty point by means of flow control. It is important to note that the selected head has a tolerance of 5% due to the tolerance of the pump curve. Consequently, there is a risk that the pump will generate head which will differ from the selected head. If the required head is the exact value of the process, it is recommended to select the pump with a larger impeller diameter to ensure the required head is obtained. It may also be necessary to adjust to the required duty point by means of flow control due to the tolerance. Flow control method is more specifically described in 7.3.2.
Pump Sizing
7.4.2 Example 2
The following example shows a centrifugal pump to be sized for a typical dairy process. Pump A is a Raw Milk pump in connection with a pasteuriser. The raw milk is pumped from a Balance tank to a Separator via the preheating stage in the plate heat exchanger.
CIP
Milk out
PHE
Pump A Balance Tank
Standardised Milk
P = 1.5 bar
Separator
As described in 7.1 in order to correctly size any type of pump, some essential information is required such as Product/Fluid data, Performance data and Site Services data. All the data has been given by the customer. Product/Fluid data: Fluid to be pumped Viscosity Pumping temperature Performance data: Capacity Discharge -
Raw Milk. 5 cP. 5C.
Suction
30 m/h. via 5 m of horizontal 76 mm dia. tube, plus a given number of bends, valves and a plate heat exchanger with pPHE 1 bar. Inlet pressure for the separator = 1.5 bar. 0.1 m head, plus a given number of bends and valves.
Pump Sizing
220/380v, 50 Hz.
Total head
Total discharge head Ht = ht +hft +pt Where ht = Static head to Separator. hft = Total pressure drop in discharge line. pt = Pressure in Separator. Therefore
Fig. 7.4.2b
ht = 0 m (no static head - only horizontal tube). hft = Pressure drop in tube ptube + Pressure drop in bends and valves p + Pressure drop in plate heat exchanger pPHE ptube from curve shown in 14.5 = 2 m. p is calculated to be 0 m. pPHE is given as 1.0 bar = 10 m. hft = 2 + 0 + 10 m. = 12 m. pt = 1.5 bar = 15 m.
Ht = ht +hft +pt = 0 + 12 + 15 m = 27 m (2.7 bar). Total suction head Hs = hs hfs +ps Where hs = Static suction head in Balance tank. hfs = Total pressure drop in suction line. ps = Pressure in Balance tank (open tank). Therefore hs = 0.1 m. hfs = calculated to be 0.4 m. ps = 0 (open tank).
Hs = hs hfs +ps = 0.1 0.4 + 0 m = 0.3 m ( 0.03 bar). Total head H = Ht Hs = 27 ( 0.3) = 27.3 m 27 m (2.7 bar).
Pump Sizing
NPSHa
NPSHa = Pa + hs hfs Pvp. Where Pa = Pressure absolute above level of fluid in Balance tank. hs = Static suction head in Balance tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 1 bar (open tank) = 10 m. 0.1 m. Calculated to be 0.4 m. at temperature of 5oC this is taken as being negligible i.e. 0 bar a = 0 m.
NPSHa = 10 + 0.1 0.4 0 (m) = 9.7 m. As the fluid to be pumped has physical properties (i.e. viscosity) different from water, the pump performance curves should not be used, and actual pump sizing should be made using the pump selection program. For this particular example, pump sized would be as follows: Pump model Impeller size Speed Capacity Head Efficiency NPSHr Motor size LKH-20. 149 mm. 2840 rev/min. 30 m/h. 27.1 m (2.71 bar). 65.9%. 1.4 m. 4 kW.
Cavitation check: NPSHa should be greater than NPSHr i.e. 9.7 m > 1.4 m, i.e. no cavitation will occur. The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a single mechanical seal with carbon/silicon carbide faces and EPDM elastomers.
Pump Sizing
7.5 Worked Examples of Centrifugal Pump Sizing (US units)

7.5.1 Example 1
The following example shows a pump to be sized for a typical brewery process. The pump is required to handle Wort from the Whirlpool to the Fermentation vessel.
Yeast CIP CO2 CO2 Fermentation CIP CO2 CO2
9 psi (pressure vessel) Cooling

69 ft
O2 Wort pump Yeast pitching Whirlpool
262 ft
As described in 7.1 in order to correctly size any type of pump, some essential information is required such as Product/Fluid data, Performance data and Site Services data.
Pump Sizing
All the above data have been given by the customer.
Product/Fluid data: Fluid to be pumped Viscosity Pumping temperature Performance data: Capacity Discharge -
Wort. 1 cP. 194F.
176 US gall/min. via 262 ft of 4 in dia. tube, plus a given number of bends, valves and a plate heat exchanger with pPHE 23 psi. Static head in Fermenting vessel = 69 ft. Pressure in Fermenting vessel = 9 psi. 1.5 ft head, plus a given number of bends and valves.
Suction
230/460v, 60 Hz.
Total head
Total discharge head Ht = ht +hft +pt Where ht = Static head in Fermentation vessel. hft = Total pressure drop in discharge line. pt = Pressure in Fermentation vessel. Therefore
Fig. 7.5.1b
ht = 69 ft. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p + Pressure drop in plate heat exchanger pPHE ptube from curve shown in 14.5 = 6 ft. p is calculated to be 16 ft. pPHE is given as 23 psi = 53 ft. hft = 6 + 16 + 53 ft. = 75 ft. pt = 9 psi = 20 ft.
Ht = ht +hft +pt = 69 + 75 + 20 ft = 164 ft (71 psi).
Pump Sizing
Total suction head Hs = hs hfs +ps Where hs = Static suction head in Whirlpool. hfs = Total pressure drop in suction line. ps = Pressure in Whirlpool (open tank). Therefore hs = 1.5 ft. hfs = calculated to be 3 ft. ps = 0 (open tank).
Hs = hs hfs +ps = 1.5 3 + 0 m = 1.5 ft ( 0.6 psi). Total head H = Ht Hs = 164 ( 1.5) = 165.5 ft 166 ft (72 psi).
NPSHa
NPSHa = Pa + hs hfs Pvp. Where Pa = Pressure absolute above level of fluid in Whirlpool tank. hs = Static suction head in Whirlpool tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 14.7 psi (open tank) = 33.9 ft. 1.5 ft. Calculated to be 3 ft. 10 psia (from table 14.4a) = 23 ft.
NPSHa = 33.9 + 1.5 3 23 (ft) = 9.4 ft. Actual pump sizing can be made using pump performance curves or a pump selection program. The performance curves are, however, not suitable if the fluid to be pumped has physical properties (i.e. viscosity) different from water. In this particular example both the pump performance curves and pump selection program can be used. The performance curve selection procedure is more specifically described in 7.3.1. For this particular example, pump sized would be as follows: Pump model Impeller size Speed Capacity Head Efficiency NPSHr Motor size LKH-20. 6.50 in. 3500 rev/min. 176 US gall/min. 166.2 ft (72 psi). 67.2%. 7.5 ft. 15 hp.
Pump Sizing
Cavitation check: NPSHa should be greater than NPSHr i.e. 9.4 ft > 7.5 ft, i.e. no cavitation will occur. The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a double mechanical seal with carbon/silicon carbide faces and EPDM elastomers.
1: Full vessel 2: Empty vessel ht1 1 2
ht2
Q2 Fig. 7.5.1c
Special Note The discharge head (ht2) is lower when the pump starts filling the fermenting vessel compared to the discharge head (ht1) when the vessel is full. The reduction of the discharge head can result in cavitation and overloading of the motor due to a capacity increase. Cavitation can be avoided by reducing the pump speed (reducing NPSHr), i.e. by means of a frequency converter, or by throttling the discharge line (increasing head). The flow control method is more specifically described in 7.3.2. Adjustment In this example the pump is sized by the pump selection program which results in exact impeller diameter of 6.50 in, so that the selected duty point is as close to the required duty point as possible. The pump is sized with a standard impeller diameter if using the performance curve. In this case it may be necessary to adjust the selected duty point by means of flow control. It is important to note that the selected head has a tolerance of 5% due to the tolerance of the pump curve. Consequently, there is a risk that the pump will generate head which will differ from the selected head. If the required head is the exact value of the process, it is recommended to select the pump with a larger impeller diameter to ensure the required head is obtained. It may also be necessary to adjust to the required duty point by means of flow control due to the tolerance. Flow control method is more specifically described in 7.3.2.
Pump Sizing
7.5.2 Example 2
The following example shows a centrifugal pump to be sized for a typical dairy process. Pump A is a Raw Milk pump in connection with a pasteuriser. The raw milk is pumped from a Balance tank to a Separator via the preheating stage in the plate heat exchanger.
CIP
Milk out
PHE
Pump A Balance Tank
Standardised Milk
P = 22 psi
Separator
As described in 7.1 in order to correctly size any type of pump, some essential information is required such as Product/Fluid data, Performance data and Site Services data. All the data has been given by the customer. Product/Fluid data: Fluid to be pumped Viscosity Pumping temperature Performance data: Capacity Discharge -
Raw Milk. 5 cP. 41F.
Suction
132 US gall/min. via 16 ft of horizontal 3 in dia. tube, plus a given number of bends, valves and a plate heat exchanger with pPHE 15 psi. Inlet pressure for the separator = 22 psi. 0.3 ft head, plus a given number of bends and valves.
Pump Sizing
230/460v, 60 Hz.
Total head
Total discharge head Ht = ht +hft +pt Where ht = Static head to Separator. hft = Total pressure drop in discharge line. pt = Pressure in Separator. Therefore
Fig. 7.5.2b
ht = 0 ft (no static head - only horizontal tube). hft = Pressure drop in tube ptube + Pressure drop in bends and valves p + Pressure drop in plate heat exchanger pPHE ptube from curve shown in 14.5 = 6 ft. p is calculated to be 0 ft. pPHE is given as 15 psi = 34 ft. hft = 6 + 0 + 34 ft. = 40 ft. pt = 22 psi = 50 ft.
Ht = ht +hft +pt = 0 + 40 + 50 ft = 90 ft (39 psi). Total suction head Hs = hs hfs +ps Where hs = Static suction head in Balance tank. hfs = Total pressure drop in suction line. ps = Pressure in Balance tank (open tank). Therefore hs = 0.3 ft. hfs = calculated to be 1.3 ft. ps = 0 (open tank).
Hs = hs hfs +ps = 0.3 1.3 + 0 m = 1 ft ( 0.4 psi). Total head H = Ht Hs = 90 ( 1) = 91 ft (39 psi).
Pump Sizing
NPSHa
NPSHa = Pa + hs hfs Pvp Where Pa = Pressure absolute above level of fluid in Balance tank. hs = Static suction head in Balance tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 14.7 psi (open tank) = 33.9 ft. 0.3 ft. Calculated to be 1.3 ft. at temperature of 41o F this is taken as being negligible i.e. 0 psia = 0 ft.
NPSHa
= 33.9 + 0.3 1.3 0 (ft) = 32.9 ft.
As the fluid to be pumped has physical properties (i.e. viscosity) different from water, the pump performance curves should not be used, and actual pump sizing should be made using the pump selection program. For this particular example, pump sized would be as follows: Pump model Impeller size Speed Capacity Head Efficiency NPSHr Motor size LKH-10. 5.59 in. 3500 rev/min. 132 US gall/min. 92 ft (40 psi). 64.7%. 4.7 ft. 5.0 hp.
Cavitation check: NPSHa should be greater than NPSHr i.e. 32.9 ft > 4.7 ft, i.e. no cavitation will occur. The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a single mechanical seal with carbon/silicon carbide faces and EPDM elastomers.
Pump Sizing

7.6.1 Slip
Slip is the fluid lost by leakage through the pump clearances. The direction of slip will be from the high pressure to the low pressure side of the pump i.e. from pump outlet to pump inlet. The amount of slip is dependent upon several factors.
Fig. 7.6.1a Slip
Slip
Inlet
Slip Slip
Outlet
Low pressure
High Pressure
Clearance effect Increased clearances will result in greater slip. The size and shape of the rotor will be a factor in determining the amount of slip. Pressure effect The amount of slip will increase as pressure increases which is shown below. In Fig 7.6.1b for a given pump speed the amount of slip can be seen as the capacity at zero bar less the capacity at X bar. To overcome this amount of slip it will be necessary to increase the pump speed to maintain the capacity required as shown in Fig 7.6.1c.
Capacity 0 bar 0 bar Required capacity
Capacity at 0 bar Capacity
X bar
Slip X bar Actual capacity at X bar Speed rev/min
Speed increase to maintain capacity Speed rev/min
Fig. 7.6.1b Pressure effect
Fig. 7.6.1c Pressure effect
Pump Sizing
Viscosity effect The amount of slip will decrease as fluid viscosity increases. The effect of viscosity on slip is shown in Figs 7.6.1d, 7.6.1e and 7.6.1f below. The pressure lines will continue to move towards the zero pressure line as the viscosity increases.
0 bar Viscosity = 1 cP Required capacity X bar Viscosity = 10 cP Required capacity 0 bar X bar Viscosity = 50 cP Required capacity 0 bar X bar
Capacity
Capacity
Speed - rev/min
Capacity
Speed - rev/min
Speed - rev/min
Fig. 7.6.1d Viscosity effect
Fig. 7.6.1e Viscosity effect
Fig. 7.6.1f Viscosity effect
Pump Speed effect Slip is independent of pump speed. This factor must be taken into consideration when operating pumps at low speeds with low viscosity fluids. For example, the amount of slip at 400 rev/min pump speed will be the same as the amount of slip at 200 rev/min pump speed providing pressure is constant.
0 bar 7 bar
Capacity
Dead head Speed rev/min speed
Fig. 7.6.1g Dead head speed
The pump speed required to overcome slip is known as the dead head speed. It is important to note that flow will be positive after overcoming the dead head speed.
Pump Sizing
A summary of effects of different parameters on slip is shown below:
Slip increases with pressure
Slip
Pressure
Fig. 7.6.1h
Slip increases with clearances
Slip
Clearances
Fig. 7.6.1i
SRU pump
Slip decreases with viscosity
Slip
SX pump
Viscosity
Fig. 7.6.1j
In general terms it is common to find the recommendation for the inlet pipe size to be the same diameter as the pump inlet connection.
7.6.2 Initial Suction Line Sizing

For guidance purposes only on high viscosity duties, the suction line can be initially sized using the initial suction line sizing curve (see 14.9) where the relationship between viscosity and flow rate provides an indication of pipe sizing. For example, for a flow rate of 10 m/h on a fluid with viscosity 900 cSt, a pump with 40 mm (1 in) diameter suction line would be initially selected. It is important to note this is only an approximate guide and care should be taken not to exceed the pumps viscosity/speed limit.
Pump Sizing
7.6.3 Performance Curve

Alfa Laval rotary lobe pumps can be sized from published performance curves or a pump selection program. Due to pumphead clearances described in 8.2.2, different performance curves are used for the various temperature ratings for rotors i.e. 70C (158oF), 130C (266oF) and 200C (392oF). The SX pump range has only 150C (302oF) rotor temperature rating. For convenience viscosity units are stated as cSt. How to use the Performance Curve The performance curve consists of four different curves: Capacity as a function of speed, related to pressure and viscosity. Power as a function of speed, related to pressure and viscosity of 1 cSt. Power as a function of viscosity greater than 1 cSt. Speed as a function of viscosity. The curves are based on water at 20C (68oF) but are shown with calculated viscosity correction data. Example shown refers to the SRU pump range but the same sizing procedure is also used for the SX pump range.
Pump Sizing
Example:
Product/Fluid Data: Fluid to be pumped Viscosity SG Pumping temperature Performance Data: Capacity Total Pressure -
Vegetable Oil. 100 cSt. 0.95 30C.
3.6 m/h (15.8 US gall/min). 8 bar (116 psig).
The optimum is to size the smallest pump possible as hydraulic conditions dictate. However other factors such as fluid behaviour, solids etc. should be considered. Step 1 Find Appropriate Curve Locate a curve for the required pump model that covers the performance data. Due to the large number of curves available it is not practical to include all performance curves in this handbook. Curves can be obtained from the pump supplier. However, the sizing process would be as follows: From the initial suction line sizing curve (see 14.9), a pump with a size 25 mm (1 in) inlet connection would be required. Although the smallest pump models SRU1/005 and SRU1/008 have 25 mm (1 in) pump inlet connections, the flow rate required would exceed the pumps speed limit on the performance curve. For this particular example, we therefore need to select a performance curve for the pump model SRU2/013/LS with 70C (158oF) rotor clearances, as shown in Fig. 7.6.3a, being the next appropriate pump size.
Fig. 7.6.3a SRU2/013/LS curves
Typical Performance Curve SRU2/013/LS or HS

US GPM m 3/h
Pump Sizing
25 mm (1 in) Port
350
172
110
78
58
43
32
23
16
X 100
Pump Sizing
Step 2 - Find Viscosity and Pressure Begin with viscosity and find the intersection point with duty pressure. From example - 100 cSt and 8 bar (115 psig). Step 3 - Find Flow Rate Move diagonally downward and find intersection with required flow rate. From example 3.6 m/h (15.8 US gall/min). Step 4 - Find Speed Move vertically downward to determine necessary pump speed. From example - 600 rev/min. Step 5 - Viscosity/Port Size Check Move vertically downward and check that maximum viscosity rating has not been exceeded against relevant inlet size. From example - maximum viscosity rating 4300 cSt. Step 6 - Find Power The power required by a pump is the summation of the hydraulic power and various losses that occur in the pump and pumping system. Viscosity has a marked effect on pump energy losses. The losses being due to the energy required in effecting viscous shear in the pump clearances. Viscous power is the power loss due to viscous fluid friction within the pump (Pv factor). Typically curves are used in conjuction with equation as follows: Total Required Power (kW) = Pv x Pump speed (rev/min) + Hydraulic power at 1 cSt (kW) 10000 where Pv = Power/viscosity factor From example: At speed 600 rev/min the hydraulic power at 1 cSt is 1.3 kW, At viscosity 100 cSt the Pv factor is 1.0 Total Required Power (kW) = Pv x Pump speed (rev/min) + Hydraulic power at 1 cSt (kW) 10000 = 1.0 x 600 + 1.3 10000 = 1.36 kW
Pump Sizing
It should be noted, this is the power needed at the pump shaft and the appropriate motor power must be selected, which in this instance would be 1.5 kW being the nearest motor output power above the required power. Step 7 - Find NPSHr NPSHr can be found by looking at the appropriate NPSH pump curve, which is a function of speed and expressed in metres water column (mwc) or feet (ft).
50
100000 cSt 60000 cSt
45
30000 cSt 20000 cSt
40
10000 cSt
35
5000 cSt
30 25
2500 cSt
20
14.4
15
4.4
1000 cSt
10
1 cSt
0
Feet Water
Metres Water
Speed rev/min
Fig. 7.6.3b SRU2 typical NPSHr curve based on water
From example - at speed 600 rev/min the NPSHr is 4.4 mwc (14.4 ft).
Pump Sizing
7.6.4 Pumps fitted with Bi-lobe Rotors (Stainless Steel)

These rotors, described in 8.2.1, are mainly used on high viscosity products containing solids where the pumps volumetric efficiency is high. When pumping such products optimum performance is obtained by using large slow running pumps. Applications on water like viscosity fluids would result in decreased efficiency over stainless steel tri-lobe rotors. For sizing purposes a percentage increase on the dead head speed (see table below) should be applied to the performance curve for stainless steel tri-lobe rotors and interpolated accordingly.
Table 7.6.4a SRU Pump Model %age Increase Required on Tri-lobe Rotor Dead Head Speed 40 40 40 40 30 30 30 25 25 10 10 10
SRU1/005 SRU1/008 SRU2/013 SRU2/018 SRU3/027 SRU3/038 SRU4/055 SRU4/079 SRU5/116 SRU5/168 SRU6/260 SRU6/353
Pump Sizing
Example of How to Interpolate Performance Curve X rev/min represents the dead head speed for tri-lobe rotors to which a percentage increase is applied from the table shown. Pump speed for bi-lobe rotors is found accordingly.
Fig. 7.6.4a Performance curve interpolation
Capacity 0 bar 7 bar
7 bar Required capacity
Speed rev/min
X rev/min Dead head speed X rev/min + % inc.
Speed required for tri-lobe rotors
Speed required for bi-lobe rotors
7.6.5 Pumps fitted with Bi-lobe Rotors (Non Galling Alloy)

These rotors, described in 8.2.1, have very small clearances resulting in increased volumetric efficiency over stainless steel rotors when used on fluids with viscosities up to 50 cP. Pump sizing is achieved by referring to published performance curves or a pump selection program. Due to pumphead clearances described in 8.2.2, different performance curves are used for the various temperature ratings of rotors i.e. 70C (158F), 130C (266F) and 200C (392F). The use of performance curves is as described in 7.6.3.
7.6.6 Pumps fitted with Tri-lobe Rubber Covered Rotors

These rotors, described in 8.2.1, have minimal clearance and will therefore significantly improve the pumps volumetric efficiency to approx. 95%. Pump sizing is achieved by referring to published performance curves or a pump selection program. Due to the minimal pumphead clearances described in 8.2.2, there is only one temperature rating of rotors i.e. 70C (158F). The use of performance curves is as described in 7.6.3.
Pump Sizing
7.6.7 Pumps with Electropolished Surface Finish

Pump performance will be affected by electropolish surface finish to the pump head internals. For sizing purposes a percentage increase on the dead head speed (see tables below) should be applied to the performance curve for stainless steel tri-lobe rotors and interpolated accordingly.
Table 7.6.7a Pump Model SRU range %age Increase Required on Stainless Steel Tri-lobe Rotor Dead Head Speed Electropolishing Mechanical and only Electropolishing 17.0 15.1 10.8 8.5 6.7 5.5 4.6 3.8 2.9 2.4 2.0 1.7 60.0 55.0 45.8 38.0 32.7 28.5 24.8 21.0 18.0 15.5 12.8 11.4
1/005 1/008 2/013 2/018 3/027 3/038 4/055 4/079 5/116 5/168 6/260 6/353 Table 7.6.7b
Pump Model SX range
%age Increase Required on Multi-lobe Rotor Dead Head Speed Electropolishing Mechanical and only Electropolishing 12.0 9.3 8.3 7.7 6.9 6.2 5.6 5.0 4.5 4.0 3.5 2.9 2.2 1.3 60.0 47.6 40.9 38.4 34.0 31.3 28.6 25.5 22.8 19.3 17.0 14.0 11.3 6.8
1/005 1/007 2/013 2/018 3/027 3/035 4/046 4/063 5/082 5/116 6/140 6/190 7/250 7/380
Pump Sizing
7.6.8 Guidelines for Solids Handling

The following criteria should be considered when deciding the pumps ability to handle large solids in suspension. Optimum Conditions Spherical Soft, yet possess resilience and shear strength
Solids form
Solids physical properties i.e. hardness, resilience, shear strength Solids surface finish Fluid/solids proportion -
Smooth Proportion of solids to fluid is small Equal Maintained such that solids in suspension are not damaged Bi-lobe Large as possible
Relationship of fluid/solid SG Flow velocity (pump speed) -
Rotor form Port size
Tables below show the maximum spherical solids size that can be satisfactorily handled without product degradation, providing the optimum conditions are met. For non-optimum conditions these should be referred to Alfa Laval.
Table 7.6.8a SRU Model Maximum Spherical Solids Size Bi-lobe Rotors Tri-lobe Rotors mm in mm in 8 8 8 13 13 16 16 22 22 27 27 37
0.31 0.31 0.31 0.51 0.51 0.63 0.63 0.88 0.88 1.06 1.06 1.47
6 6 6 9 9 11 11 15 15 18 18 24
0.24 0.24 0.24 0.34 0.34 0.44 0.44 0.59 0.59 0.72 0.72 0.94
Pump Sizing
Table 7.6.8b
SX Model
Maximum Spherical Solids Size Multi-lobe Rotors in mm 7 7 10 10 13 13 16 16 19 19 25 25 28 28
SX1/005 SX1/007 SX2/013 SX2/018 SX3/027 SX3/035 SX4/046 SX4/063 SX5/082 SX5/116 SX6/140 SX6/190 SX7/250 SX7/380
0.28 0.28 0.39 0. 39 0.51 0.51 0.63 0.63 0.75 0.75 0.98 0.98 1.10 1.10
7.6.9 Guidelines for Pumping Shear Sensitive Media

Special attention needs to be made to pumping shear sensitive media such as yeast and yoghurt where the cell structure needs to remain intact. Excess pump speed can irreversibly damage the cell structure. Therefore pump speeds need to be kept relatively low, in the range of 100 to 400 rev/min dependent upon the fluid being pumped, pump size/model and rotor form. For these types of applications refer to Alfa Laval.
Pump Sizing
7.7 Worked Examples of Rotary Lobe Pump Sizing (Metric units)

The following examples show two different rotary lobe pumps to be sized for a typical sugar process. Pump 1 is a low viscosity example handling sugar syrup. Pump 2 is a high viscosity example handling massecuite. As described in 7.1 in order to correctly size any type of pump, information is required such as Product/Fluid data, Performance data and Site Services data. Pump 1 Thin Sugar Syrup pump
Fig. 7.7a Pump 1 - example
1 bar
1m Feed tank 8m 1m 1m 1m 2m 6m 3m
Product/Fluid data: Fluid to be pumped Viscosity SG Pumping temperature CIP temperature Performance data: Capacity Discharge -
Sugar syrup. 80 cP. 1.29. 15C. 95C.
Suction
9 m/h. via 10 m of 51 mm dia. tube, plus 1 bend 90 deg. and 1 butterfly valve Static head in vessel = 8 m. Pressure in vessel = 1 bar. via 3 m of 51 mm dia. tube, plus 2 bends 90 deg. and 1 non-return valve. Static head in tank = 2 m.
220/380v, 50 Hz.
Pump Sizing
Total head
Total discharge head Ht = ht +hft +pt Where ht = Static head in pressurised vessel. hft = Total pressure drop in discharge line. pt = Pressure in vessel. Therefore
Fig. 7.7b
ht = 8 m x (SG = 1.29) = 10.3 m. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p (calculated below). pt = 1 bar = 10 m.
To ascertain hft the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = D x V x where D V = = = = tube diameter (mm). fluid velocity (m/s). density (kg/m). absolute viscosity (cP). Q = capacity (m/h). D = tube diameter (mm).
velocity V
= Q x 353.6 where D = 9 x 353.6 51 = 1.22 m/s
density
= 1290 derived from SG value 1.29 (see 2.1.5).
Therefore Re = D x V x = 51 x 1.22 x 1290 80 = 1003 As Re is less than 2300, flow will be laminar.
Pump Sizing
Equivalent Line Length Discharge Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.1. Since flow is laminar, the viscosity correction factor is 1.0 (see 2.2.2). Straight tube length 1 bend 90 deg. 1 butterfly valve =3+6+1 = 1 x 1 x 1.0 (corr. factor) = 1 x 1 x 1.0 (corr. factor) Total equivalent length = 10 m =1m =1m = 12 m = 64 Re = 64 1003 = 0.064 The Miller equation is now used to determine friction loss as follows: Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (m). tube diameter (mm). fluid velocity (m/s). specific gravity. (bar) (bar)
Also as flow is laminar the friction factor fD
= 5 x 1.29 x 0.064 x 12 x 1.22 51 = 0.14 bar = 1.4 m
Ht = ht +hft +pt = 10.3 + 1.4 + 10 m = 21.7 m (2.17 bar). Total suction head Hs = hs hfs + ps Where hs = Static suction head in Tank. hfs = Total pressure drop in suction line. ps = Pressure in Tank (open tank). hs = 2 m x (SG = 1.29) = 2.6 m. hfs = Calculated below. ps = 0 (open tank).
Therefore
Pump Sizing
Equivalent Line Length Suction Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.1. Since flow is laminar, the viscosity correction factor is 1.0 (see 2.2.2). Straight tube length 2 bend 90 deg. 1 non-return valve =1+1+1 = 2 x 1 x 1 (corr. factor) = 1 x 12 x 1 (corr. factor) Total equivalent length =3m =2m = 12 m = 17 m = 64 Re = 64 1003 = 0.064 The Miller equation is now used to determine friction loss as follows: Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hfs) friction factor. tube length (m). tube diameter (mm). fluid velocity (m/s). specific gravity. (bar) (bar)
= 5 x 1.29 x 0.064 x 1.7 x 1.22 51 = 0.2 bar = 2 m
Hs = hs hfs + ps = 2.6 2 + 0 m = 0.6 m (0.06 bar). Total head H = Ht Hs = 21.1 0.6 = 21.1 m 21 m (2.1 bar)
Pump Sizing
NPSHa
NPSHa = Pa + hs hfs Pvp. Where Pa = Pressure absolute above fluid level in Tank. hs = Static suction head in Tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 1 bar (open tank) = 10 m. 2.6 m. calculated to be 2 m. at temperature of 15o C this is taken as being negligible i.e. 0 bar a = 0 m.
NPSHa = Pa + hs hfs Pvp = 10 + 2.6 2 0 m = 10.6 m. Actual pump sizing can be made using pump performance curves or a pump selection program. The performance curve selection procedure is more specifically described in 7.6.3. From the initial suction line sizing curve (see 14.9), a pump with a size 40 mm inlet connection would be required. Although the smallest pump models SR1/008 (with enlarged port), SRU2/013 (with enlarged port) and SRU2/018 (with sanitary port) have 40 mm pump inlet connections, the flow rate required would exceed the pumps speed limit on the performance curve. We have therefore selected a performance curve for the pump model SRU3/027/LS with 130C rotor clearances due to the CIP requirement, being the next appropriate pump size. Pump sized as follows: Pump model Connection size Speed NPSHr SRU3/027/LS. 40 mm. 606 rev/min. 3.6 m.
Cavitation check: NPSHa should be greater than NPSHr i.e. 10.6 m > 3.6 m. Viscosity/Port Size check: The viscosity of 80 cP at speed 606 rev/min is well within the pumps maximum rated figures.
Pump Sizing
Power calculation: Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 where Pv = Power/viscosity factor. From example At speed 606 rev/min and total head 2.1 bar, the power at 1 cSt is 0.9 kW, At viscosity 80 cP (62 cSt) the Pv factor is 3. Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 = 3 x 606 + 0.9 10000 = 1.1 kW It should be noted that this is the power needed at the pump shaft, and the appropriate motor power must be selected, which in this instance would be 1.5 kW being the nearest motor output power above the required power. The recommended type of shaft seal based upon Alfa Laval application experience and guidelines would be a single flushed mechanical seal with tungsten carbide/tungsten carbide faces and EPDM elastomers. Hard tungsten carbide seal faces due to the abrasive nature of sugar syrup. Flushed version to prevent the sugar syrup from crystallising within the seal area. EPDM elastomers for compatibility of both sugar syrup and CIP media.
Pump Sizing
Pump 2 Massecuite pump

Fig. 7.7c Pump 2 - example
20 m 2m 1m 40 m
Product/Fluid data: Fluid to be pumped Viscosity SG Pumping temperature Performance data: Capacity Discharge -
Massecuite. 25000 cP. 1.35 65C.
Suction
10 m/h. via 40 m of 76 mm dia. tube, plus 2 bends 45 deg. and 1 butterfly valve Static head in tank = 20 m. via 1 m of 101.6 mm dia. tube, plus 1 bend 90 deg. and 1 butterfly valve. Static head in tank = 2 m.
220/380v, 50 Hz.
Pump Sizing
Total head
Fig. 7.7d
ht = 20 m x (SG = 1.35) = 27 m. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p (calculated below). pt = 0 bar (open tank) = 0 m.
To ascertain hft the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = D x V x where D V = = = = tube diameter (mm). fluid velocity (m/s). density (kg/m). absolute viscosity (cP). Q = capacity (m/h). D = tube diameter (mm).
velocity V
= Q x 353.6 where D = 10 x 353.6 76 = 0.61 m/s
density
= 1350 derived from SG value 1.35 (see 2.1.5).
Therefore Re = D x V x = 76 x 0.61 x 1350 25000 = 2.5 As Re is less than 2300, flow will be laminar.
Pump Sizing
Equivalent Line Length Discharge Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.1. Since flow is laminar, the viscosity correction factor is 0.25 (see 2.2.2). Straight tube length 2 bend 45 deg. 1 butterfly valve = 40 m = 0.5 m = 0.5 m = 41 m = 64 Re = 64 2.5 = 25.6 The Miller equation is now used to determine friction loss as follows: Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (m). tube diameter (mm). fluid velocity (m/s). specific gravity. (bar) (bar)
= 2 x 1 x 0.25 (corr. factor) = 1 x 2 x 0.25 (corr. factor) Total equivalent length
= 5 x 1.35 x 25.6 x 41 x 0.61 76 = 34.7 bar = 347 m
Ht = ht +hft +pt = 27 + 347 + 0 m = 374 m (37.4 bar). Total suction head Hs = hs hfs +ps Where hs = Static suction head in Tank. hfs = Total pressure drop in suction line. ps = Pressure in Tank (open tank). hs = 2 m x (SG = 1.35) = 2.7 m. hfs = Calculated below. ps = 0 (open tank).
Therefore
Pump Sizing
To ascertain hfs the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = D x V x where D V = = = = tube diameter (mm). fluid velocity (m/s). density (kg/m). absolute viscosity (cP). Q = capacity (m/h). D = tube diameter (mm).
velocity V
= Q x 353.6 where D = 9 x 353.6 101.6 = 0.34 m/s
density Therefore Re
= 1350 derived from SG value 1.35 (see 2.1.5). = DxVx = 101.6 x 0.34 x 1350 25000 = 1.9
As Re is less than 2300, flow will be laminar. Equivalent Line Length Suction Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.1. Since flow is laminar, the viscosity correction factor is 0.25 (see 2.2.2).
Pump Sizing
Straight tube length 1 bend 90 deg. 1 butterfly valve
=1m = 0.5 m = 0.5 m =2m = 64 Re = 64 1.9 = 33.68
The Miller equation is now used to determine friction loss as follows:
Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG =
(bar)
pressure loss due to friction (hfs) friction factor. tube length (m). tube diameter (mm). fluid velocity (m/s). specific gravity. (bar)
= 5 x 1.35 x 33.68 x 2 x 0.34 101.6 = 0.52 bar = 5.2 m Hs = hs hfs +ps = 2.7 5.2 + 0 m = 2.5 m.
Total head H = Ht Hs = 374 (2.5) = 376.5 m 377 m (37.7 bar) In this example the total head required is in excess of the 20 bar maximum working pressure of the pump. To reduce this head so as a pump can be suitably sized, consideration could be given to any or a combination of the following parameters: 1. 2. 3. 4. Reduce capacity. Increase tube diameter. Increase pumping temperature to reduce viscosity. Consider two or more pumps in series.
Pump Sizing
Assuming the capacity is a definite requirement and the pumping temperature cannot be increased the customer should be advised to increase the discharge tube diameter i.e. from 76 mm to 101.6 mm. The total head calculations are reworked, and for this particular example the fluid velocity (V) and friction factor (fD) have already been established for 101.6 mm diameter tube. Also note, by referring to the equivalent tube length table 14.7.1 the values for bends 45 deg. and butterfly valves remain unchanged. Using the Miller equation to determine friction loss as follows: Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (m). tube diameter (mm). fluid velocity (m/s). specific gravity. (bar) (bar)
= 5 x 1.35 x 33.68 x 41 x 0.34 101.6 = 10.6 bar = 106 m
Now Ht = ht + hft +pt = 27 + 106 + 0 m = 133 m (13.3 bar). Now Total head H = Ht Hs = 133 (2.5) = 135.5 m 136 m (13.6 bar)
NPSHa
NPSHa = Pa + hs hfs Pvp. Where Pa = hs = hfs = Pvp= Pa = hs = hfs = Pvp= Pressure absolute above fluid level in Tank. Static suction head in Tank. Total pressure drop in suction line. Vapour pressure of fluid. 1 bar (open tank) = 10 m. 2.7 m. calculated to be 5.2 m. at temperature of 65 oC this is taken as being negligible i.e. 0 bar a = 0 m.
Therefore
Pump Sizing
NPSHa = Pa + hs hfs Pvp = 10 + 2.7 5.2 0 m = 7.5 m. Due to the high viscosity it is not practical to use pump performance curves for sizing purposes. The actual pump sizing can be made using a pump selection program. An approximate guide to pump sizing can be made by calculation using volumetric efficiency. For this particular example a pump sized from the pump selection program using stainless steel tri-lobe rotors with 130C rotor clearances would be as follows: Pump model Connection size Speed NPSHr SRU5/168/LD. 100 mm (enlarged port). 100 rev/min. 2.1 m.
Cavitation check: NPSHa should be greater than NPSHr i.e. 7.5 m > 2.1 m. Viscosity/Port Size check: The viscosity of 25000 cP at speed 100 rev/min is well within the pumps maximum rated figures. Power calculation: Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 where Pv = Power/viscosity factor. From example At speed 100 rev/min and total head 13.6 bar, the power at 1 cSt is 4.1 kW, at viscosity 25000 cP (18519 cSt) the Pv factor is 110. Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 = 110 x 100 + 4.1 10000 = 5.2 kW
Pump Sizing
It should be noted that this is the power needed at the pump shaft, and for a fixed speed drive the appropriate motor power must be selected, which in this instance would be 5.5 kW being the nearest motor output power above the required power. The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a packed gland arrangement with polyamide gland packing on hard coated shaft sleeves with EPDM elastomers. Alternative shaft sealing could be a flushed packed gland or double flushed mechnical seal. Alternative Pump Sizing Guide Using Volumetric Efficiency Calculation. Referring to the initial suction line sizing curve shown in 14.9, for the flow rate required of 10 m3/h with viscosity 25000 cP (18519 cSt), a pump having a 100 mm dia. inlet port would be selected. For this example a Model SRU5/168 pump will be selected having 100 mm dia. enlarged ports. If a sanitary port is a definite requirement the Model SRU6/260 pump would be selected. To calculate pump speed for the SRU5/168 pump selected the following formula is used as a general guide with volumetric efficiency of 99% (see 7.2.4). Pump speed (rev/min) n = Q x 100 q x v x 60 where: Q = capacity (m3/h) q = pump displacement (m3/100 rev) v = vol. efficiency (99% = 0.99) = 10 x 100 0.168 x 0.99 x 60 = 100 rev/min
Pump Sizing
7.8 Worked Examples of Rotary Lobe Pump Sizing (US units)

The following examples show two different rotary lobe pumps to be sized for a typical sugar process. Pump 1 is a low viscosity example handling sugar syrup. Pump 2 is a high viscosity example handling massecuite. As described in 7.1 in order to correctly size any type of pump, information is required such as Product/Fluid data, Performance data and Site Services data. Pump 1 Thin Sugar Syrup pump
Fig. 7.8a Pump 1 - example
15 psi
Feed tank
3 ft
26 ft 3 ft 3 ft 3 ft 6 ft 10 ft 20 ft
Product/Fluid data: Fluid to be pumped Viscosity SG Pumping temperature CIP temperature Performance data: Capacity Discharge -
Sugar syrup. 62 cSt. 1.29. 59F. 203F.
Suction
40 US gall/min. via 33 ft of 2 in dia. tube, plus 1 bend 90 deg. and 1 butterfly valve. Static head in vessel = 26 ft. Pressure in vessel = 15 psi. via 9 ft of 2 in dia. tube, plus 2 bends 90 deg. and 1 non-return valve. Static head in tank = 6 ft.
230/460v, 60 Hz.
Pump Sizing
Total head
Fig. 7.8b
ht = 26 ft x (SG = 1.29) = 33.5 ft. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p (calculated below). pt = 15 psi = 35 ft.
To ascertain hft the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = 3162 x Q Dx where D = tube diameter (in). Q = capacity (US gall/min). = kinematic viscosity (cSt). = 3162 x 40 2 x 62 = 1020 As Re is less than 2300, flow will be laminar.
Pump Sizing
Equivalent Line Length Discharge Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.2. Since flow is laminar, the viscosity correction factor is 1.0 (see 2.2.2). Straight tube length 1 bend 90 deg. 1 butterfly valve = 10 + 20 + 3 = 1 x 3 x 1.0 (corr. factor) = 1 x 3 x 1.0 (corr. factor) Total equivalent length = 33 ft = 3 ft = 3 ft = 39 ft = 64 Re = 64 1020 = 0.063 The Miller equation is now used to determine friction loss as follows: Pf = 0.0823 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (ft). tube diameter (in). fluid velocity (ft/s). specific gravity. (psi)
Velocity V
= Q x 0.409 where Q = capacity (US gall/min) D2 D = tube diameter (in) = 40 x 0.409 22 = 4.1 ft/s
Pf
= 0.0823 x 1.29 x 0.063 x 39 x 4.1 2 = 2.2 psi = 5 ft
(psi)
Ht = ht +hft +pt = 33.5 + 5 + 35 ft = 73.5 ft 74 ft (32 psi). Total suction head Hs = hs hfs +ps
Pump Sizing
Where
hs = Static suction head in Tank. hfs = Total pressure drop in suction line. ps = Pressure in Tank (open tank). hs = 6 ft x (SG = 1.29) = 7.7 ft. hfs = Calculated below. ps = 0 (open tank).
Therefore
Equivalent Line Length Suction Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.2. Since flow is laminar, the viscosity correction factor is 1.0 (see 2.2.2). Straight tube length = 3 + 3 + 3 2 bend 90 deg. = 2 x 3 x 1 (corr. factor) 1 non-return valve = 1 x 39 x 1 (corr. factor) Total equivalent length Also as flow is laminar the friction factor fD = 9 ft = 6 ft = 39 ft = 54 ft = 64 Re = 64 1020 = 0.063 The Miller equation is now used to determine friction loss as follows: Pf = 0.0823 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hfs) friction factor. tube length (ft). tube diameter (in). fluid velocity (ft/s). specific gravity. (psi)
Velocity V
= Q x 0.409 where Q = capacity (US gall/min) D2 D = tube diameter (in) = 40 x 0.409 22

= 4.1 ft/s
Pump Sizing
Pf
= 0.0823 x 1.29 x 0.063 x 54 x 4.1 2 = 3 psi = 7 ft
(psi)
Hs = hs hfs +ps = 7.7 7 + 0 ft = 0.7 ft (0.3 psi). Total head H = Ht Hs =74 0.7 = 73.3 ft 73 ft (32 psi).
NPSHa
NPSHa = Pa + hs hfs Pvp. Where Pa = Pressure absolute above fluid level in Tank. hs = Static suction head in Tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 14.7 psi (open tank) = 33.9 ft. 7.7 ft. calculated to be 7 ft. at temperature of 59o F this is taken as being negligible i.e. 0 psia = 0 ft.
NPSHa = Pa + hs hfs Pvp = 33.9 + 7.7 7 0 ft = 34.6 ft. Actual pump sizing can be made using pump performance curves or a pump selection program. The performance curve selection procedure is more specifically described in 7.6.3. From the initial suction line sizing curve (see 14.9), a pump with a size 1.5 in inlet connection would be required. Although the smallest pump models SR1/008 (with enlarged port), SRU2/013 (with enlarged port) and SRU2/018 (with sanitary port) have 1.5 in pump inlet connections, the flow rate required would exceed the pumps speed limit on the performance curve. We have therefore selected a performance curve for the pump model SRU3/027/LS with 266F rotor clearances due to the CIP requirement, being the next appropriate pump size. Pump sized as follows: Pump model Connection size Speed NPSHr SRU3/027/LS. 1.5 in. 613 rev/min. 11.9 ft.
Cavitation check: NPSHa should be greater than NPSHr i.e. 34.6 ft > 11.9 ft.
Pump Sizing
Viscosity/Port Size check: The viscosity of 62 cSt at speed 613 rev/min is well within the pumps maximum rated figures. Power calculation: Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 where Pv = Power/viscosity factor. From example At speed 613 rev/min and total head 32 psi, the power at 1 cSt is 1.2 hp, At viscosity 62 cSt the Pv factor is 3. Total Required Power (kW) = Pv x Pump speed (rev/min) + Power at 1 cSt (kW) 10000 = 3 x 613 + 1.2 10000 = 1.4 hp It should be noted that this is the power needed at the pump shaft, and the appropriate motor power must be selected, which in this instance would be 2 hp being the nearest motor output power above the required power. The recommended type of shaft seal based upon Alfa Laval application experience and guidelines would be a single flushed mechanical seal with tungsten carbide/tungsten carbide faces and EPDM elastomers. Hard tungsten carbide seal faces due to the abrasive nature of sugar syrup. Flushed version to prevent the sugar syrup from crystallising within the seal area. EPDM elastomers for compatibility of both sugar syrup and CIP media.
Pump Sizing
Pump 2 Massecuite pump

Fig. 7.8c Pump 2 - example
65 ft 6 ft 3 ft 130 ft
Product/Fluid data: Fluid to be pumped Viscosity SG Pumping temperature Performance data: Capacity Discharge -
Massecuite. 18519 cSt. 1.35 149F.
Suction
44 US gall/min. via 130 ft of 3 in dia. tube, plus 2 bends 45 deg. and 1 butterfly valve Static head in tank = 65 ft. via 3 ft of 4 in dia. tube, plus 1 bend 90 deg. and 1 butterfly valve. Static head in tank = 6 ft.
230/460v, 60 Hz.
Pump Sizing
Total head
Fig. 7.8d
ht = 65 ft x (SG = 1.35) = 88 ft. hft = Pressure drop in tube ptube + Pressure drop in bends and valves p (calculated below). pt = 0 psi (open tank) = 0 ft.
To ascertain hft the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = 3162 x Q Dx where D = tube diameter (in). Q = capacity (US gall/min). = kinematic visosity (cSt). = 3162 x 44 3 x 18519 = 2.5 As Re is less than 2300, flow will be laminar.
Pump Sizing
Equivalent Line Length Discharge Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.2. Since flow is laminar, the viscosity correction factor is 0.25 (see 2.2.2). Straight tube length 2 bend 45 deg. 1 butterfly valve = 130 ft = 1.5 ft = 1.75 ft = 133 ft = 64 Re = 64 2.5 = 25.6 The Miller equation is now used to determine friction loss as follows: Pf = 5 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (ft). tube diameter (in). fluid velocity (ft/s). specific gravity. (psi)
Velocity V
= Q x 0.409 where Q = capacity (US gall/min) D2 D = tube diameter (in) = 40 x 0.409 32 = 2 ft/s
Pf
= 0.0823 x 1.35 x 25.6 x 133 x 2 3 = 504 psi = 1163 ft
(psi)
Ht = ht +hft +pt = 88 + 1163 + 0 ft = 1251 ft (542 psi). Total suction head Hs = hs hfs +ps
Pump Sizing
Where
hs = Static suction head in Tank. hfs = Total pressure drop in suction line. ps = Pressure in Tank (open tank). hs = 6 ft x (SG = 1.35) = 8 ft. hfs = Calculated below. ps = 0 (open tank).
Therefore
To ascertain hfs the flow characteristic and equivalent line length must be determined as follows: Flow Characteristic Reynolds number Re = 3162 x Q Dx where D = tube diameter (in). Q = capacity (US gall/min). = kinematic visosity (cSt). = 3162 x 44 4 x 18519 = 1.9 As Re is less than 2300, flow will be laminar. Equivalent Line Length Suction Side The equivalent lengths of straight tube for bends and valves are taken from table 14.7.2. Since flow is laminar, the viscosity correction factor is 0.25 (see 2.2.2). Straight tube length 1 bend 90 deg. 1 butterfly valve = 3 ft = 1.75 ft = 1.75 ft = 6.5 ft = 64 Re = 64 1.9 = 33.68
Pump Sizing
The Miller equation is now used to determine friction loss as follows: Pf = 0.0823 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hfs) friction factor. tube length (ft). tube diameter (in). fluid velocity (ft/s). specific gravity. (psi)
Velocity V
= Q x 0.409 where Q = capacity (US gall/min) D2 D = tube diameter (in) = 44 x 0.409 42 = 1.1 ft/s
Pf
= 0.0823 x 1.35 x 33.68 x 6.5 x 1.1 4 = 7.4 psi = 17 ft
(psi)
Hs = hs hfs +ps = 8 17 + 0 ft = 9 ft. Total head H = Ht Hs = 1251 (9) = 1260 ft (546 psi) In this example the total head required is in excess of the 290 psi maximum working pressure of the pump. To reduce this head so as a pump can be suitably sized, consideration could be given to any or a combination of the following parameters: 1. 2. 3. 4. Reduce capacity. Increase tube diameter. Increase pumping temperature to reduce viscosity. Consider two or more pumps in series.
Assuming the capacity is a definite requirement and the pumping temperature cannot be increased the customer should be advised to increase the discharge tube diameter i.e. from 3 in to 4 in.
Pump Sizing
The total head calculations are reworked, and for this particular example the fluid velocity (V) and friction factor (fD) have already been established for 4 in diameter tube. Also note, by referring to the equivalent tube length table 14.7.2 the values for bends 45 deg. and butterfly valves remain unchanged. Using the Miller equation to determine friction loss as follows: Pf = 0.0823 x SG x fD x L x V D Where: Pf = fD = L = D = V = SG = pressure loss due to friction (hft) friction factor. tube length (ft). tube diameter (in). fluid velocity (ft/s). specific gravity. (psi) (psi)
= 0.0823 x 1.35 x 33.68 x 133 x 1.1 4 = 150 psi = 346 ft
Now Ht = ht + hft +pt = 88 + 346 + 0 ft = 434 ft (188 psi). Now Total head H = Ht Hs = 434 (9) = 443 ft (192 psi).
NPSHa
NPSHa = Pa + hs hfs Pvp . Where Pa = Pressure absolute above fluid level in Tank. hs = Static suction head in Tank. hfs = Total pressure drop in suction line. Pvp= Vapour pressure of fluid. Therefore Pa = hs = hfs = Pvp= 14.7 psi (open tank) = 33.9 ft. 8 ft. calculated to be 17 ft. at temperature of 149o F this is taken as being negligible i.e. 0 psia = 0 ft.
NPSHa = Pa + hs hfs Pvp = 33.9 + 8 17 0 m = 24.9 ft.
Pump Sizing
Due to the high viscosity it is not practical to use pump performance curves for sizing purposes. The actual pump sizing can be made using a pump selection program. An approximate guide to pump sizing can be made by calculation using volumetric efficiency. For this particular example a pump sized from the pump selection program using stainless steel tri-lobe rotors with 266 F rotor clearances would be as follows: Pump model Connection size Speed NPSHr SRU5/168/LD. 4 in (enlarged port). 100 rev/min. 6.9 ft.
Cavitation check: NPSHa should be greater than NPSHr i.e. 24.9 ft > 6.9 ft. Viscosity/Port Size check: The viscosity of 18519 cSt at speed 100 rev/min is well within the pumps maximum rated figures. Power calculation: Total Required Power (hp) = Pv x Pump speed (rev/min) + Power at 1 cSt (hp) 10000 where Pv = Power/viscosity factor. From example At speed 100 rev/min and total head 192 psi, the power at 1 cSt is 5.5 hp, At viscosity 18519 cSt the Pv factor is 110. Total Required Power (hp) = Pv x Pump speed (rev/min) + Power at 1 cSt (hp) 10000 = 110 x 100 + 5.5 10000 = 6.6 hp It should be noted that this is the power needed at the pump shaft, and for a fixed speed drive the appropriate motor power must be selected, which in this instance would be 7.5 hp being the nearest motor output power above the required power.
Pump Sizing
The recommended shaft seal type based upon Alfa Laval application experience and guidelines would be a packed gland arrangement with polyamide gland packing on hard coated shaft sleeves with EPDM elastomers. Alternative shaft sealing could be a flushed packed gland or double flushed mechnical seal. Alternative Pump Sizing Guide Using Volumetric Efficiency Calculation. Referring to the initial suction line sizing curve shown in 14.9, for the flow rate required of 44 US gall/min with viscosity 18519 cSt, a pump having a 4 in dia. inlet port would be selected. For this example a Model SRU5/168 pump will be selected having 4 in dia. enlarged ports. If a sanitary port is a definite requierement the Model SRU6/260 would be selected. To calculate pump speed for the SRU5/168 pump selected the following formula is used as a general guide with volumetric efficiency of 99% (see 7.2.4). Pump speed (rev/min) n = Q x 100 q x v where: Q = capacity (US gall/min) q = pump displacement (US gall/100 rev) v = vol. efficiency (99% = 0.99) = 44 x 100 44.39 x 0.99 = 100 rev/min
Pump Specification Options
8. Pump Specification Options

This section gives detailed descriptions of the various specification options available for the Alfa Laval pump ranges, such as port connections, heating/cooling jackets, pressure relief valves and other ancillaries.
8.1 Centrifugal and Liquid Ring Pumps

8.1.1 Port Connections
Pumps are supplied with screwed male connections of all major standards, i.e.: SMS, DIN, ISO, BS, DS, GC-clamp, bevel seat, DC and H-line.
Pump Range Pump Model Inlet mm LKH LKH-5 LKH-10 LKH-15 LKH-20 LKH-25 LKH-35 LKH-40 LKH-45 LKH-50 LKH-60 LKH-70 LKH-80 LKH-112 LKH-113 LKH-114 LKH-122 LKH-123 LKH-124 LKHP-10 LKHP-15 LKHP-20 LKHP-25 LKHP-35 LKHP-40 LKHP-45 LKHP-50 LKHP-60 50 65 100 65 80 65 80 100 100 100 100 150 50 50 50 80 80 80 65 100 65 80 65 80 100 100 100 Nominal Connection Size Inlet Outlet mm in 40 50 80 50 65 50 65 80 80 100 80 100 40 40 40 65 65 65 50 80 50 65 50 65 80 80 100
Outlet in 1.5 2 3 2 2.5 2 2.5 3 3 4 3 4 1.5 1.5 1.5 2.5 2.5 2.5 2 3 2 2.5 2 2.5 3 3 4
2 2.5 4 2.5 3 2.5 3 4 4 4 4 6 2 2 2 3 3 3 2.5 4 2.5 3 2.5 3 4 4 4
LKH-Multistage
LKHP
Pump Range
Pump Model Inlet mm
Nominal Connection Size Outlet Inlet mm in 50 50 65 50 65 50 80 50 65 50 65 80 80 100 50 50 65 50 50 50 80 80 80
Outlet in 2 2 2.5 2 2.5 2 3 2 2.5 2 2.5 3 3 4 2 2 2.5 2 2

2 3 3 3
LKHSP
LKHSP-10 LKHSP-20 LKHSP-25 LKHSP-35 LKHSP-40 LKHI-10 LKHI-15 LKHI-20 LKHI-25 LKHI-35 LKHI-40 LKHI-45 LKHI-50 LKHI-60 LKH-10 LKH-20 LKH-25 LKH-35 LKH-40 MR-166S MR-185S MR-200S MR-300
65 65 80 65 80 65 100 65 80 65 80 100 100 100 65 65 80 65 80 50 80 80 80
2.5 2.5 3 2.5 3 2.5 4 2.5 3 2.5 3 4 4 4 2.5 2.5 3 2.5 3

2 3 3 3
LKHI
LKH-UltraPure
MR
Table 8.1.1a
8.1.2 Heating/Cooling Jackets

In some applications heating of the fluid being pumped may be required to reduce the fluid viscosity so that satisfactory operation is achieved. Alternatively it may be necessary to cool the fluid being pumped where heat is generated by means of the fluid repeatedly being passed through the pump. On such occasions some pump models can be fitted with heating/cooling jackets.
Pump casing
Jacket
Fig. 8.1.2a Heating/Cooling jacket
8.1.3 Pump Casing with Drain

In some applications it is a requirement that no fluid should be left in the pump casing. This can be achieved by either: - Turning the pump outlet downwards - Fitting a drain connection to the bottom of the pump casing
or
Pump casing Fig. 8.1.3a Turned pump casing
Drain Fig. 8.1.3b Pump casing with drain
Back plate
Gap: 2 mm
8.1.4 Increased Impeller Gap

Impeller
In some applications, e.g. when using a LKH centrifugal pump as a booster pump in a cream pasteurisation unit, there is a risk that a hard layer of proteins will slowly build up between the backside of the impeller and the back plate. This will activate the thermal relay of the motor after a few hours of operation so that the pump stops. The operating time of the pump can be increased by increasing the standard gap width between the back of the impeller and the back plate, from 0.5 mm to 2.5 mm. The gap is achieved by machining the back of the impeller. This increased gap reduces the head by approx. 5%. For this type of application it is recommended to select a motor size with an output power one step higher than the standard selection so as to avoid the motor thermal relay being constantly activated.
Fig. 8.1.4a Increased gap
8.1.5 Pump Inlet Inducer

Inducer
In some applications it may be necessary to improve the suction conditions by means of fitting the pump inlet with an inducer. This has the effect of improving NPSH requirements for difficult applications and/or assisting the flow of a viscous fluid into the pump casing.
Impeller
Inlet
Fig. 8.1.5a Inducer in pump inlet

8.2.1 Rotor Form
Table 8.2.1a Rotor Form Material Pump Range SRU SX ! ! ! ! !
Tri-lobe Tri-lobe Bi-lobe Bi-lobe Multi-lobe
Stainless steel Rubber covered Stainless steel Non galling alloy Stainless steel
Fig. 8.2.1a Bi-lobe
Fig. 8.2.1b Tri-lobe
Fig. 8.2.1c Multi-lobe
Tri-lobe Rotors (Stainless steel) Most duties can be accomplished by pumps fitted with stainless steel tri-lobe rotors. The tri-lobe rotor with its mathematically correct profile and precision manufacture ensure interchangeability as well as smooth, high performance pumping action. These are available on the SRU pump range with 3 temperature ratings: up to 70C (158oF). up to 130C (266oF). up to 200C (392oF). and pressures up to 20 bar (290 psig).
Large fluid chamber
Bilobe rotors
Bi-lobe Rotors (Stainless steel) These are generally used for handling delicate suspended solids where minimum product damage is required. Typical applications are jam containing fruit pieces, sausage meat filling, petfood, soups and sauces containing solid matter. These are available on the SRU pump range with 3 temperature ratings: up to 70C (158oF). up to 130C (266oF). up to 200C (392oF). and pressures up to 20 bar (290 psig). Bi-lobe Rotors (Non galling alloy) Manufactured from non-galling alloy these rotors have an advantage over stainless steel, as smaller clearances (see 8.2.2) can be used, leading to increased efficiencies. These are available on the SRU pump range with 3 temperature ratings: up to 70C (158oF). up to 130C (266oF). up to 200C (392oF). and pressures up to 20 bar (290 psig). Tri-lobe Rubber Covered Rotors This rotor has a stainless steel insert covered in NBR rubber, and due to the resilience of the rubber coating these rotors have a slight interference fit with the pump rotorcase when initially fitted. This results in improved pump performance and suction lift capability over stainless steel tri-lobe rotors. Rotors are suitable for continuous operation up to 70C (158oF) and intermittent operation up to 100C (212oF), and pressures up to 7 bar (100 psig). Multi-lobe Rotors This rotor is manufactured from stainless steel and as the name suggests has many lobes. For the SX pump range these rotors have 4 lobes and are designed to maximise efficiency, reduce shear and provide a smooth pumping action. Rotors are suitable for temperatures up to 150C (302oF) and pressures up to 15 bar (215 psig).
Gentle pumping action Fig. 8.2.1d Bi-lobe rotors for solids handling
Clearances are necessary to avoid rotor to rotor, rotor to rotorcase and rotor to rotorcase cover contact. The size of these clearances is related to the pressure and temperature of pump operation and rotor material.
Fig. 8.2.2a Clearances
8.2.2 Clearances
Within the pump head are clearances, which are the spaces between rotating components and between rotating and stationary components. The key clearances are as follows: Radial clearance (between rotor tip and rotorcase). Mesh clearance (between rotors). Front clearance (between front of rotor and rotorcase cover). Back clearance (between back of rotor and back face of rotorcase).
Radial Back
Mesh Front
Pressure effect The design concept of the rotary lobe pump is to have no contacting parts in the pumphead. This requires having the shaft support bearings to be mounted outside of the pumphead, which results in an overhung load, caused by the rotors fitted to the shafts (see Fig. 8.2.2b). The effect of pressure on the rotors will cause shaft deflection, which could result in contact between rotors, rotorcase and rotorcase cover. As product wetted parts of the SRU and SX pump ranges are predominantly manufactured from stainless steel, any contact between rotating and stationary parts would cause galling and possible pump seizure. To allow for this pressure effect, clearances are built into the pumphead between surfaces that may contact. For the SRU and SX pump ranges there is only one pressure rating, which is the maximum differential pressure of the particular pump model. The pressure effect is less significant on pumps fitted with rubber covered or non-galling alloy rotors.
Fig. 8.2.2b Pressure effect Force due to pressure Support bearings
Shaft Rotor
Overhang length
Outlet
Inlet
Rotorcase Rotor
Shaft Standard clearance Standard rotor width
Temperature effect Temperature change can be caused by the fluid being pumped, pump mechanism, drive unit and/or the environment. Any CIP operation required should also be taken into consideration (see section 10 for detailed explanation of CIP). Changes in temperature will cause expansion upon heating or contraction upon cooling, to the rotorcase and gearcase components. The most significant result is movement between shaft and gearcase/rotorcase causing the rotors to move forward/backward in the rotorcase, thereby reducing the front clearance. To compensate for this, the SRU pump range has increased clearances as shown below. SRU pumps are designed for various temperature ratings for rotors i.e. 70C (158F), 130C (266F) or 200C (392F). On the SX pump range the design of the mechanical seal eliminates contact between the fluid being pumped and the shaft. This results in the shaft not being subjected to the full temperature variation and therefore only one temperature rating of 150C (302F) is necessary.
Thermal expansion
Increased clearance
Decreased rotor width
The clearance is exaggerated to show the temperature effect Fig. 8.2.2c Increased clearance
8.2.3 Port Connections

Pumps are supplied with screwed male connections to all major standards as follows:
Table 8.2.3a Standard Screwed Connection Type 3A/Asme BSP BSPT DIN11851/405 ISS/IDF NPT RDG RJT SMS Tri-Clamp (BS4825) Pump Range SRU SX ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
All models in the SRU and SX pump ranges are supplied with full bore through porting, conforming to International Sanitary Standards BS4825 / ISO2037. This provides effective CIP cleaning and maximises inlet and outlet port efficiency and NPSHr characteristics. The option of the enlarged port on the SRU pump range can be chosen for high viscosity applications.
Fig. 8.2.3a Sanitary port design
Fig. 8.2.3b Enlarged port design
The SRU pump range when having enlarged ports can also be supplied with flanged connections of all major standards i.e. ASA/ANSI125, ASA/ANSI150, ASA/ANSI300, BS10 table E, BS10 table F, BS4504/DIN2533 and JIS10K. Flanges for vertically ported pumps are not fitted directly to the discharge port. In this instance an elbow bend is included to which the flange is fitted.
Pump Range
Pump Model Sanitary mm
Nominal Connection Size Enlarged in mm
in 1.5 1.5 2 2 2.5 2.5 3 3 4 4 6
SRU
SRU1/005 SRU1/008 SRU2/013 SRU2/018 SRU3/027 SRU3/038 SRU4/055 SRU4/079 SRU5/116 SRU5/168 SRU6/260 SRU6/353 SX1/005 SX1/007 SX2/013 SX2/018 SX3/027 SX3/035 SX4/046 SX4/063 SX5/082 SX5/115 SX6/140 SX6/190 SX7/250 SX7/380
25 25 25 40 40 50 50 65 65 80 100 100 25 40 40 50 50 65 50 65 65 80 80 100 100 150
1 1 1 1.5 1.5 2 2 2.5 2.5 3 4 4 1 1.5 1.5 2 2 2.5 2 2.5 2.5 3 3 4 4 6
40 40 50 50 65 65 80 80 100 100 150
SX
For size 150 mm (6 in) screwed male connections, these are only available as DIN11851/405, SRJT or Tri-Clamp (BS4825).
Table 8.2.3b
8.2.4 Rectangular Inlets

Hopper Rectangular inlet
Outlet
For handling extremely viscous products and/or large solids that would naturally bridge a smaller port, SRU rotary lobe pumps can be supplied with a rectangular inlet. Usually the pump will be in vertical port orientation to allow the product to flow into the pumping chamber under gravity from a hopper mounted directly above or mounted with an adaptor to facilitate connection to large diameter pipework. As can be seen from the table below there is a significant percentage area increase when using a rectangular inlet compared to a sanitary port connection. This increases the pumps ability to handle highly viscous products.
Fig. 8.2.4a Rectangular inlets
Table 8.2.4a
Pump Model
Sanitary port area (mm2)
Rectangular inlet area (mm2)
% area increase above sanitary port diameter 171 326 314 206 221 189 151 151 176 195 186 244
387 387 387 957 957 1780 1780 2856 2856 4185 7482 7482
660 1260 1216 1976 2112 3360 2688 4320 5032 8160 13888 18240
Connections for steam, hot/cold fluid
Saddle
8.2.5 Heating/Cooling Jackets and Saddles

Rotary Lobe pumps can be fitted with jackets to the rotorcase cover and saddles to the rotorcase. These are primarily used for warming the pumphead so as to prevent the fluid pumped being cooled and become viscous or allowed to solidify/crystallise. These can also be used for cooling purposes. The maximum pressure and temperature of heating/cooling fluid is 3.5 bar (50 psig) and 150C (302oF) respectively. Heating/cooling jackets and saddles should be in operation approximately 15 minutes prior to pump start up and remain in operation 15 minutes after pump shut down. Typical applications include: Adhesive Chocolate Gelatine Jam Resin Jackets are available on both the SRU and SX pump ranges, but saddles are only available on the SRU pump range.
Jacket Fig. 8.2.5a Heating/Cooling jackets and saddles
8.2.6 Pump Overload Protection

Due to the positive action of the rotary lobe pump any restriction on the outlet side of the pump, either partial or total, will result in excessive pressure developing in the pumphead. It is therefore essential that some form of overload protection be installed to protect pump, drive unit and also limit pressure build up within associated process equipment. This protection will normally take the form of an external spring-loaded pressure relief valve fitted to the outlet side of the pump which will open under high pressure and allow fluid to return to the inlet side of the pump via a by-pass loop. Other alternatives are to fit the pump with an integral relief valve as described below, or use of proprietary electronic devices. Pressure Relief Valves These can be supplied as an integral part of the pump and do not require external pipework. The assembly replaces the standard rotorcase cover and is intended to protect the pump from over pressurisation. It is suitable for bi-direction pump operation and can be retrofitted. The valve will provide full pump protection for fluids having viscosities below 500 cP, above this figure Alfa Laval should be consulted with regard to specific flow rates in relation to viscosity and differential pressures. The design is such that the valve mechanism is isolated from the pumped fluid. Valve open
Rotors Rotor nuts Large slip path across rotorcase cover
Pressure relief valve
Fig. 8.2.6a Pressure relief valve
Valve closed
Small slip path across rotorcase cover
Relief valve piston
Relief valve piston moves back against the springs
Fig. 8.2.6b Relief valve operation
As it is a mechanical device the relief valve does not operate instantaneously due to mechanical response time. The valve will begin to relieve at a pressure less than the fully open pressure. This accumulation will vary depending upon the duty pressure, viscosity and pump speed. The accumulation tends to increase as pressure or pump speed decrease, and as viscosity increases. The valve is set to relieve at the required pressure by the correct choice of springs and can be adjusted on site to suit actual duty requirements. The relief valve can be provided with the following options: Automatic with Pneumatic Override These valves may be pneumatically overridden for CIP conditions and they may be remotely controlled if required. Air supply should be clean and dry at pressures of 4 bar (60 psig) minimum and 8 bar (115 psig) maximum. Automatic with Manual Override This valve has a lever to enable manual override for CIP or certain tank filling applications.
Valve Type Pump Range - Availability Normal Operating Pressure Range bar psig 7-19 7-19 19 7-10 7
Standard Pneumatic override Manual override
SRU1-6 SRU1-6 SRU1-3 SRU4-5 SRU6
100-275 100-275 275 100-145 100
Table 8.2.6a
Pressure relief valves are only available for the SRU range pumps fitted with metal rotors. Pump Protection Unit (PPU) The Pump Protection Unit is a non-intrusive alternative to mechanical relief valves, conventional electronic shear pin or mechanical over-load protection devices. It is designed to protect Alfa Laval rotary lobe pumps and incorporates micro-controller technology. The PPU is not a power meter or data-logging device but has the ability to monitor true consumption through continuous power monitoring. The PPU is not a pre-set device and requires a simple set-up procedure to be carried out to suit specific duty conditions of the pump to be monitored. After initial setting is completed the monitoring process is automatic and the pump is under the protection of the PPU.
Fig. 8.2.6c Pump protection unit
The PPU will detect over-load and rapidly increasing load. One example of an over-load condition could result from a gradual increase in viscosity of the pumped media. This condition would in turn result in a higher discharge pressure, therefore increased power consumption. Another example could result from a partially closed valve in the discharge pipe also giving rise to excess pressure and therefore power consumption. As well as responding to system related transients, the PPU will also respond to mechanical changes such as bearing or lubrication failure, both of which could result in pump seizure if not detected and corrected. The PPU will detect a rapidly increasing load such as that caused by a solid object entering the pump and becoming trapped between the rotors. The resulting rapid power increase from this type of event, even within the lines of the over-load trip threshold, will cause an automatic shutdown if desired thereby limiting the degree of damage. The PPU will detect under-load since this highlights a condition preventing optimum pump operating efficiency. One example of under-load could result from a blocked or closed valve in the inlet pipe, a burst inlet or outlet pipe, or even an empty supply vessel.
8.2.7 Ancillaries
Rotary Lobe pumps can be supplied bare shaft (without drive) or mounted on a baseplate with drive such as electric motor, air motor, and diesel or petrol engine dependent upon customer requirements and services available. Electric motors being the most commonly used method of drive, are described in more detail in section 9.
Fig. 8.2.7a Typical motorised rotary lobe pump unit
Fixed Speed Rotary Lobe pumps generally operate at low to medium speeds i.e. 25 to 650 rev/min, and therefore some form of speed reduction is required from normal AC motor synchronous speeds of 1500, 1000 and 750 rev/min for 50 Hz (1800, 1200 and 900 rev/min for 60 Hz). This is generally achieved by using a geared electric motor direct coupled to the pump drive shaft via flexible coupling. An alternative arrangement would be an electric motor with a wedge belt pulley drive reducing the motor speed to the pump output speed required.
When exact flow is not critical a fixed speed drive is generally used. The integral geared electric motor is the most commonly used type of fixed speed drive. This is a compact low cost unit, which is easy to install, as it only requires one coupling and a safety guard. Complete ranges of drive speeds are available from the different manufacturers and usually one can be found within a few rev/min of the required speed. Some pumps operate continuously for 24 hours per day and others operate intermittently. How a pump operates will determine the choice of geared electric motor. Motor manufacturers give recommendations for their motors relating to the number of hours per day of operation and the frequency of starting and stopping. Variable Speed To handle changing duty conditions or a number of different duties, it may be necessary to use a variable speed drive or frequency converter to obtain correct pump duty speeds. There are many types of mechanical and hydraulic variable speed drives available in a wide range of speeds, which are well suited to rotary lobe pump characteristics by offering the ability to adjust the pump speed to control flow and adjust for system conditions. The frequency converter allows the operator to change the frequency of the electric motor, thereby changing pump speed and controlling flow (see 9.10). Other Drive Types Air motors, although not commonly used as pump drives, can provide good low cost drive in certain applications. In addition diesel or petrol engines can be used as pump drivers. Baseplates The Alfa Laval standard is a pressed mild steel or stainless steel design which is required to be bolted to the floor (see 12.3). The Alfa Laval mild steel baseplate is supplied painted to suit customer requirements and the stainless steel has a dull polish finish. An alternative is to mount the pump and drive unit on a portable trolley design baseplate complete with control gear and trailing lead as required. In some application areas such as dairy or brewing it is normal practice to hose down pump units and floorings in these circumstances ball feet can be fitted to baseplates, which can be a fixed or variable height, to raise baseplate above floor level. Baseplates can also be designed to meet specific customer standards when required.
Guards All rotating machinery should be adequately guarded and when pumps are supplied complete with a drive, a guard is fitted over the transmission (flexible coupling or wedge belt) which links the pump drive shaft to the output shaft of the selected driver. The selection of guard material is important relative to its working environment. Non-sparking materials such as aluminium or brass are used with flameproof/explosion proof motors in hazardous areas. For non-hazardous applications mild steel or stainless steel is generally used.
Motors
9. Motors
This section describes electric motors, including information on motor protection, methods of starting, motors for hazardous environments and speed control.
The electric motor is the most commonly used method of pump drive, due to the following: Electrical power supply is usually readily available and easy to install. High efficiency due to low losses when transforming from electrical to mechanical power. The electric motor can absorb variations in the torque requirement of a pump, i.e. as a result of changes in product/ duty conditions, inertia in the bearings, frequent starts etc. Easy speed control.
All Alfa Laval pump ranges can be fitted with AC type Totally Enclosed Fan Ventilated (TEFV) squirrel cage three phase electric motors complying with various international standards and regulations such as IEC, CENELEC, VDE, DIN and BS. Electric motors supplied in the USA are generally to NEMA standard. Single phase electric motors can also be fitted to Alfa Laval rotary lobe pumps.
Fig. 9a Electrical hazard
Motors
The standard design of an AC motor includes the following main parts: Item 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Description Stator housing. Ball bearings. Bearing housing. Fan. Fan cap. Housing for electrical connection. Iron core. Three phase windings. Rotor. Motor shaft.
Fig. 9b Exploded view of a typical AC motor
The motor is constructed as follows: which The stator is fixed in the stator housing (1). The ball bearings (2) are fixed in the bearing housing (3), close the stator housing. The ball bearings carry the rotor (9) and the motor shaft (10). The fan (4), which cools the motor, is fixed to the motor shaft. The fan is protected by means of the fan cap (5). The housing for electrical connection (6) is situated on the stator housing. There is an iron core (7) in the stator housing. The iron core consists of thin iron sheets with a thickness of 0.3 0.5 mm. The three phase windings (8) are situated in the grooves of the iron core. The three phase windings and the stator core are designed to produce a magnetic field in pairs of poles. When the stator is connected to a three-phase supply voltage the magnetic fields of the individual phase windings form a symmetrically rotating magnetic field which is called the rotational field. The speed of the rotational field is called the synchronous speed.
Motors
9.1 Output Power

The output power is always lower than the rated electrical power due to various losses in the motor. The ratio of output power to rated electrical power is known as the motor efficiency. The table below shows output power that is specified in standard ratings.
Frequency 50 Hz 60 Hz 50 Hz 60 Hz Table 9.1a 0.37 0.43 11 12.7 0.55 0.63 15 17.5 0.75 0.86 18.5 21 Output Power in kW 1.1 1.27 22 25 1.5 1.75 30 35 2.2 2.5 37 42 3 3.5 45 52 4 4.6 55 64 5.5 6.3 75 87 7.5 8.6 90 105
Frequency 60 Hz 0.5 15
Table 9.1b (Nema motors)
Output Power in hp 0.75 20 1 25 1.5 30 2 40 3 50 5 60 7.5 75 10 100
9.2 Rated Speed

The rated speed of the motor is always lower than the synchronous speed due to motor slip. The connection between synchronous speed, rated speed, frequency and poles is shown in the table below:
No. Poles No. Pairs of poles Synchronous speed at 50 Hz - rev/min Rated speed at 50 Hz - rev/min Synchronous speed at 60 Hz - rev/min Rated speed at 60 Hz - rev/min Table 9.2a 2 1 3000 2880 3600 3460 4 2 1500 1440 1800 1720 6 3 1000 960 1200 1150 8 4 750 720 900 860 12 6 500 480 720 690
Motors
9.3 Voltage
Standard motors for use on 3 phase 50 or 60 Hz can be wound for any single voltage as follows: Up to 3 kW (4 hp) 4 kW (5.5 hp) and over 230 to 400 volts. 400 to 690 volts.
Euronorm motors supplied at 400 volts will generally operate satisfactorily with voltage variations of 10% from the rated voltage.
9.4 Cooling
Motor cooling is specified by means of the letters IC (International Cooling) in accordance with standards. The most common is IC411 (Totally Enclosed Fan Ventilated - TEFV) where an externally mounted fan cools the motor. Methods of cooling are shown below:
Code IC411 IC410 IC418 IC416 Table 9.4a Arrangement Totally Enclosed Fan Ventilated (TEFV) motor cooled by an externally mounted fan Totally Enclosed Non Ventilated (TENV) self cooling, no externally mounted fan Totally Enclosed Air Over Motor (TEAOM) motor cooled by airstream Totally Enclosed Forced Cooled (TEFC) motor cooled by an independent fan
9.5 Insulation and Thermal Rating

Standard motors will operate satisfactorily in an ambient temperature range of - 20C (-68o F) to + 40C (104o F) (class B temperature rise) and at altitudes up to 1000 metres above sea level. Motors supplied with class F insulation system with only class B temperature rise (80C) (176o F) ensure an exceptional margin of safety and longer life even in abnormal operating conditions such as withstanding ambient temperatures up to 55C (131o F) or 10% overload or adverse supply systems. Motors operating in ambient temperatures higher than 55C (131o F) will have class H insulation. Some derating of the motor may be necessary for high ambient temperatures and high altitude.
Motors
9.6 Protection
The degree of motor protection is specified by means of the letters IP (International Protection) in accordance with standards. These state the method of determining degrees of ingress protection for both dust and water. The letters IP are followed by two digits, the first of which specifies the protection against contact and ingress of foreign bodies and the second digit specifies the protection against water. Table showing degrees of protection is shown below:
Designation 1st Digit Protection against contact and ingress of foreign bodies IP44 Protection against contact with live or moving parts by tools, wires or other objects of thickness greater than 1 mm. Protection against the ingress of solid foreign bodies with a diameter greater than 1 mm. Complete protection against contact with live or moving parts inside the enclosure. Protection against harmful deposits of dust. The ingress of dust is not totally prevented, but dust cannot enter in an amount sufficient to interfere with satisfactory operation of the machine. No ingress of dust. 2nd Digit Protection against water Water splashed against the motor from any direction shall have no harmful effect.
IP54 IP55
Water splashed against the motor from any direction shall have no harmful effect. Water projected by a nozzle against the motor from any direction shall have no harmful effect. Motor protected against conditions on a ships deck or powerful water jets. Water projected by a nozzle against the motor from any direction shall have no harmful effect.
IP56 IP65
Table 9.6a
Tropic Proof Treatment Motors operating in tropical climates are invariably subjected to hot, humid and wet conditions, which will produce considerable amounts of condensation on internal surfaces. Condensation occurs when the surface temperature of the motor is lower than the dew-point temperature of the ambient air. To overcome this motors can be supplied with special tropic proof treatment. Failure to include this treatment and the resulting corrosion can cause irreparable damage to stator windings and moving parts. Anti-Condensation Heaters Where the motor is to be left standing for long periods of time in damp conditions it is recommended that anti-condensation heaters are fitted and energised to prevent condensation forming in the motor enclosure. These heaters are normally 110 volts or 220 volts.
Motors
Thermistors To protect the motor windings from overload due to high temperature, motors can be fitted with thermistors, which are temperature-dependent semi-conductor devices embedded in the motor windings. Where motors can be allowed to operate at slow speed, i.e. being used with a frequency converter (see 9.9), it is normal to fit thermistors to prevent the motor from overloading or to insufficient cooling from the motor fan.
Motors
9.7 Methods of Starting

There are three starting methods: 1. Direct On Line (D.O.L.). 2. Star/Delta (Y/). 3. Soft. Direct On Line Starting The connection between supply voltage and rated current is very important with regards to motor starting. The simplest way to start the motor is to connect directly the mains supply to the motor. In this case the starting current is high, often 5 to 8 times higher than the rated current. Motors fitted to centrifugal and liquid ring pumps are normally directly started, as the moment of inertia of the motor is low due to pump design and the fluids being pumped having low viscosities. In this case the starting time with high starting current is very low and it can consequently be ignored. Star/Delta (Y/) Starting If pumping viscous fluids the starting time with the high starting current is longer. It can, therefore, be necessary to restrict the starting current by means of Y/ - starting of the motor. The current can be restricted by starting the motor in Y-connection and then changing to -connection.
Fig. 9.7a Connection of three-phase single speed motor
Soft Starting The soft start provides a smooth start at the same time, as the starting current is limited. The magnitude of the starting current is directly dependent on the static torque requirement during a start and on the mass of the load that is to be accelerated. In many cases the soft starter saves energy by automatically adapting the motor voltage continually to the actual requirement. This is particularly important when the motor runs with a light load. Soft starting can also be achieved using a frequency converter.
Motors
9.8 Motors for Hazardous Environments

Zones The degree of hazard varies from extreme too rare. Hazardous areas are classified into three Zones as follows: By implication, an area that is not classified Zone 0, 1 or 2 is deemed to be a non-hazardous or safe area.
Zone 0, in which an explosive gas-air mixture is continuously present or present for long periods No motors may be used in this zone. Zone 1, in which an explosive gas-air mixture is likely to occur in normal operation. Zone 2, in which an explosive gas-air mixture is not likely to occur in normal operation and if it occurs it will only be present for a short time.
To ensure equipment can be safely used in hazardous areas, its gas group must be known and its temperature class must be compared with the spontaneous ignition temperature of the gas mixtures concerned.
Table 9.8a
Temperature class T1 T2 T3 T4 T5 T6
Ignition temperature for gas/vapour up to 450oC (842oF) 300 to 450oC (572 to 842oF) 200 to 300oC (410 to 572oF) 135 to 200oC (275 to 410oF) 100 to 135oC (212 to 275oF) 85 to 100oC (185 to 212oF)
Max. permitted temperature of electrical equipment 450oC (842oF) 300oC (572oF) 200oC (410oF) 135oC (275oF) 100oC (212oF) 85oC (185oF)
Group I Group II IIA IIB IIC Table 9.8b
Equipment for coal mines susceptible to methane gas. Equipment for explosive atmospheres other than mines i.e. surface industries. Group II is subdivided according to the severity of the environment. IIC is the highest rating. A motor from one of the higher categories can also be used in a lower category.
Motors
Flameproof Enclosure - EEx d and EEx de These motors are designated for operation in Zone 1 hazardous areas. The motor enclosure is designed in such a way that no internal explosion can be transmitted to the explosive atmosphere surrounding the machine. The enclosure will withstand, without damage, any pressure levels caused by an internal explosion. The temperature of the motors external enclosure should not exceed the self-ignition temperature of the explosive atmosphere of the installation area during operation. No motor device outside the flameproof area shall be a potential source of sparks, arcs or dangerous overheating. Variants combining two types of protection usually combine d and e types of protection. The most commonly used and recognised by the CENELEC European Standards is the EEx de variant. The motor is designed with an EEx d flameproof enclosure, while the terminal box features an EEx e increased safety protection. Such design combines the superior safety degree of the d type of protection with the less stringent electrical connection requirements of increased safety motors. Increased Safety Design - EEx e The design of this motor type prevents the occurrence of sparks, arcs or hot spots in service, that could reach the self-ignition temperature of the surrounding, potentially explosive atmosphere, in all inner and outer parts of the machine. Non-Sparking Design EEx nA, Ex nA, Ex N These motors are designated for operation in Zone 2 hazardous areas. The motor construction is similar to standard TEFV motors, but with special attention to eliminate production of sparks, arcs or dangerous surface temperatures. The British Standard is the type Ex N version. The marking according to standard EN 50021 is EEx nA, where EEx n = European standard for Ex product with protection n, A = for nonsparking equipment.
Motors
The classification parameters of motors for hazardous areas can be summarised as below:
Fig. 9.8a Overview of classification parameters
Severe environments Reinforced protection Corrosive atmospheres Zone 2 Accidental presence Zone 1 Incidental presence Zone 0 Permanent presence Ex nA Ex N EEx e T6 85 C T5 100 C T4 135 C T3 200 C T2 300 C T1 450 C EEx d/EEx de EEx e EEx p
Standards IEC BS EN
Environment Mines Explosive atmospheres Other than mines
Group I IIA IIB IIC
Gas Methane Propane Ethane Hydrogen
9.9 Energy Efficient Motors

In October 1998, the European Union and CEMEP (The European Committee of Manufacturers of Electrical Machines and Power Electronics) agreed to introduce three efficiency classes for electric motors. This agreement forms part of the European Commissions aims to improve energy efficiency and reduce CO2 emissions. The burning of fossil fuels to generate electricity, primarily consumed by households and industry, is a major source of greenhouse gas emissions. Industry will, therefore, have a major part to play in reducing harmful emissions. For instance by increasing the efficiency of their production processes, and installing energy efficient devices, industrial processes will consume less electricity. This, in turn, will reduce the amount of electricity that must be generated to meet demand.
Motors
Motors account for around 65% of the electric energy consumed in industrial applications. Energy saving is dependent upon the kW rating of the motor, the loading and the hours run. As such, higher efficiency motors can play a significant part in reducing CO2 emissions. An energy efficient motor produces the same output power (torque) but uses less electrical input power (kW) than a standard electric motor. This higher efficiency is achieved by using higher quality and thinner laminations in the stator to reduce core loss and more copper in the slots to reduce current and resistance losses. The three efficiency classes designated EFF1, EFF2 and EFF3, apply to TEFV, 2 and 4 pole, squirrel cage induction motors in the power range 1.1 to 90 kW (1.5 to 125 hp) rated for 400 volts, 50 Hz. For intermittent usage, EFF3 class motors can be used and for continuous usage EFF1 or EFF2 motors should be used.
2 pole Motor Output Power hp kW EFF1 equal to or above 82.8 84.1 85.6 86.7 87.6 88.6 89.5 90.5 91.3 91.8 92.2 92.9 93.3 93.7 94.0 94.6 95.0 Efficiency % EFF2 equal to or above 76.2 78.5 81.0 82.6 84.2 85.7 87.0 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9 EFF3 below
Table 9.9a
1.1 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90
1.5 2 3 4 5.5 7.5 10 15 20 25 30 40 50 60 75 100 125
76.2 78.5 81.0 82.6 84.2 85.7 87.0 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9
Motors
Table 9.9b Output Power hp kW
4 pole Motor EFF1 equal to or above 83.8 85.0 86.4 87.4 88.3 89.2 90.1 91.0 91.8 92.2 92.6 93.2 93.6 93.9 94.2 94.7 95.0 Efficiency % EFF2 equal to or above 76.2 78.5 81.0 82.6 84.2 85.7 87.0 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9 EFF3 below
1.1 1.5 2.2 3 4 5.5 7.5 11 15 18.5 22 30 37 45 55 75 90
1.5 2 3 4 5.5 7.5 10 15 20 25 30 40 50 60 75 100 125
76.2 78.5 81.0 82.6 84.2 85.7 87.0 88.4 89.4 90.0 90.5 91.4 92.0 92.5 93.0 93.6 93.9
9.10 Speed Control

The effective speed control of AC electric motors has long been regarded as an adaptable and economical means of reducing costs and saving energy. Speed control can be multi-speed, variable voltage or frequency converter. Multi-Speed Pole Change (Tapped or Dahlander) These have a single winding and two speeds in a ratio of 2:1 and can be supplied for constant torque or variable torque applications. PAM (Pole Amplitude Modulation) Similar to above except that pole variations can be 4/6 or 6/8. Dual Wound Motors have two separate windings and can be supplied for any two speed combinations. A combination of dual and pole change windings can give 3 or 4 speeds from one design.
Motors
Variable Voltage Variable voltage control provides a low capital cost means of varying the motor speed on centrifugal pumps. This form of speed control requires greater derating than for converter drives and is best suited to 4 pole machines of 2:1 speed reduction with close matching of motor output to absorbed pump load. These motors are of special design standard motors being unsuitable. Frequency Converter The use of a frequency converter will allow speed control of a standard AC motor by adjusting the frequency, although some derating may be necessary. Basic frequency converters will permit operation over a typical speed range of 20:1. With increasing sophistication such as vector control, e.g. field oriented control utilising closed loop feedback; the effective speed range can be increased to 1000:1. For applications using variable torque loads such as centrifugal pumps, very little derating will be required. For applications using constant torque loads such as rotary lobe pumps, the level of derating will depend on the speed range required. The motor ratings must take into account the following: Increased heating due to the harmonic content of the inverter waveforms. Reduced cooling arising from motor speed reduction. The power or torque requirements throughout the entire speed range. Other limiting factors such as maximum motor speeds, ambient temperature, altitude etc.
As well as motors being remotely controlled by frequency converters, electric motors can be made available with the frequency converter already fitted to the motor. These arrangements are generally available for motors up to 7.5 kW (10 hp) and have the advantage of not using any shielded motor cables, as there are no extra connections between the frequency converter and motor. Also providing room in a switch cabinet will not be necessary.
Motors
9.11 Changing Motor Nameplates - Centrifugal and Liquid Ring Pumps only
In some instances there are non-standard electrical requirements regarding combinations of supply voltage, frequency and output power. When selecting a motor for a centrifugal or liquid ring pump, special attention should be given to the rated speed and output power. As viewed from table below which shows an example for a motor frame size 90LB, the rated speed and output power will vary dependent upon the combination of supply voltage and frequency. For complete list see section 14.8. It is therefore very important to specify supply voltage, frequency and required power, to correctly size the motor.
Motor Frame Size 90LB 90LB Frequency Hz Supply Voltage v 220-240/380-420Y 200 440-480Y 200 220 380Y Output Power kW 2.2 2.2 2.5 2.1 2.3 2.3 Motor Nameplate Rated Speed rev/min 2900 2860 3500 3430 3470 3450 Power Factor Rated Current A 8.1/4.7 8.7 4.4 8.3 7.5 4.8
50 60
Standard New Standard New New New
0.85 0.90 0.86 0.91 0.90 0.91
Table 9.11a
Standard supply voltage, frequency and output power The motors can be used in the standard version without any modifications for the standard supply voltage, frequency and output power combinations. This is shown in section 9.1. For example, if using a motor frame size 90LB, from the table above, the motor can be used as standard as follows: 50 Hz, 220-240v/380-420vY, 2.2 kW 60 Hz, 440-480vY, 2.5 kW Non-standard supply voltage, frequency and output power If a non-standard combination of supply voltage, frequency and output power is required, the standard motor with a new nameplate or a special motor with an appropriately stamped nameplate can be used. Examples of this are as follows using a motor frame size 90LB from the table above.
Motors
Example 1 - For 60 Hz, 380vY, 2.2 kW
1. Use a standard motor frame size 90LB. 2. The appropriate electrical data must be changed on the motor nameplate. 3. The motor will give an output power of 2.3 kW, which is sufficient, as 2.2 kW is required. 1. 2. The standard motor frame size 90LB will only give 2.3 kW, which is not sufficient. Select the nearest larger standard motor i.e. frame size 100LB. This will give 3.2 kW, which is sufficient, as 2.5 kW is required. The appropriate electrical data must be changed on the motor nameplate. Alternatively select a specially wound motor to give the required 2.5 kW at the non-standard supply voltage and frequency combination.
Example 2 For 60 Hz, 380vY, 2.5 kW
3.
Motors
Cleaning Guidelines for use in Processes utilising CIP Systems
10. Cleaning Guidelines for use in Processes utilising CIP (Clean In Place) Systems
This section provides cleaning guidelines for use in processes utilising CIP (Clean In Place) systems. Interpretations of cleanliness are given and explanations of the cleaning cycle.
The following recommendations offer advice on how to maximise the CIP (Clean In Place) efficiency of the Alfa Laval ranges of centrifugal and rotary lobe pumps. The guidelines incorporate references to internationally recognised cleaning detergents, velocities, temperatures and pressures used to clean other types of flow equipment, such as valves and fittings, but have been specifically prepared to maximise the CIP effectiveness of our pumps. The perception of the word clean will vary from customer to customer and process to process. The four most common interpretations of Clean are given below: 1. Physical Cleanliness This is the removal of all visible dirt or contamination from a surface. This level of cleanliness is usually verified by a visual test only. 2. Chemical Cleanliness This is defined as the removal of all visible dirt or contamination as well as microscopic residues, which are detectable by either taste or smell but not by the naked eye. 3. Bacteriological Cleanliness This can only be achieved with the use of a disinfectant that will kill all pathogenic bacteria and the majority of other bacteria. 4. Sterility Quite simply this is the destruction of all known micro-organisms. The following recommendations for CIP will address the first three definitions.
In most installations it is important to ensure the maximum recovery of pumped product residues from the production line at the end of each production run. Where this is a requirement, consideration should be given to mounting rotary lobe pumps with ports in the vertical plane to maximise drainability. This will minimise any product loss, ease the cleaning of the system and reduce the requirement to dispose of or recycle the wash from the initial cleaning cycles. By maximising the recovery of product from the system both the efficiency of the production and cleaning processes will be increased. Rotary lobe pumps are rarely used as the supply pump for CIP fluids. Centrifugal pumps are generally used during CIP for each phase of the cleaning cycle. For the majority of CIP cycles it is recommended that a differential pressure of 2 to 3 bar is created across the pump to promote efficient cleaning, whilst it is rotating at its normal operating speed. In many cases a valve is employed in the discharge line of the system to create the differential pressure across the pump and a by-pass loop installed around the pump to divert any excess of CIP liquid that the pump is unable to transfer. The valve(s) setting may be fluctuated during the CIP cycle to promote pressure/flow variations that may enhance the cleaning process. During the CIP cycle there must always be sufficient flow of cleaning fluid being delivered by the CIP pump to make sure that the centrifugal or rotary lobe pump is neither starved of liquid at its inlet due to its own flow capability, or overpressurised at its inlet due to its tendency to act as a restriction if it is unable to transfer the full flow of the fluid being delivered to it. Internationally accepted protocol for CIP suggest that during all phases of the CIP cycle a pipeline velocity of between 1.5 m/sec and 3.0 m/sec is required. Velocities within this range have proven to provide effective cleaning of Alfa Laval pumps, although as a general rule the higher the velocity the greater the cleaning effect. Generally the most effective cleaning processes incorporate five stages: 1. 2. 3. 4. 5. An initial rinse of clean, cold water. Rinsing with an alkaline detergent. Intermediate rinse with cold water. Rinsing with an acidic disinfectant. Final rinse with clean cold water.
The cycle times, temperatures, cleaning mediums and concentrations of the detergents used will all influence the effectiveness of the cleaning cycle and care must be taken when defining these to ensure that they are suitable for use with the particular product being pumped. Of equal importance is the chemical compatibility between the cleaning detergents and the product wetted materials in the pump head and ensuring for rotary lobe pumps the correct temperature clearance rotors are fitted for the CIP cycle. Consideration should also be given to the disposal or recycling of used cleaning liquids and the potential requirement for handling concentrated detergents. Specialists suppliers should make the final selection of cleaning detergents/disinfectants. Within these guidelines a typical cleaning cycle would be as follows: 1. Rinse with clean water at ambient temperature to remove any remaining residue. 10 to 15 minutes are usually sufficient for this part of the cycle but this will depend on the condition and volume of the residue to be removed. Rinse with an alkaline detergent, typically a 2.5% solution of Caustic Soda (NaOH) at between 70 to 95C (158 to 203oF) for a period of 20 to 30 minutes would be used. It is also common to add a wetting agent (surfactant) to lower the surface tension of the detergent and hence aid its cleansing ability. This phase of the cleaning cycle should dissolve and remove organic matter such as fats and proteins. Intermediate rinse with clean water at ambient temperature for a period of 5 to 10 minutes. This phase should remove any residual detergents. Rinse with an acidic disinfectant, typically a 2.5% solution of Nitric Acid (HNO3) at ambient temperature for a period of 10 to 15 minutes would be used. This phase of the cleaning cycle should remove proteins, mineral salts, lime and other deposits. Final rinse with clean water at ambient temperature for a period of 10 to 15 minutes or until all traces of the cleaning fluid have been removed.
2.
3.
4.
5.
During the CIP cycles it is important that the required concentration of cleaning detergents is maintained consistently. A significant increase in concentration could cause damage to pumps and other components in the system. A significant decrease in concentration could effect the detergents cleaning efficiency. A facility for monitoring and adjusting the detergent concentration should be considered. Cautionary Notes: 1. Pumps and other equipment installed in CIP systems have components within them that will expand and contract at different rates. Care should be taken not to subject them to rapid temperature cycling. Products containing particulate such as fibre, seeds or soft fleshy matter have to be evaluated carefully and on an individual basis, as the nature of these will provide an increased cleaning challenge. These types of product may typically require increased cleaning cycle times and/or increased velocities and pressures during the cleaning cycle. CIP detergent liquids and the elevated temperatures typically used for CIP processes can cause a potential health risk. Always adhere to site Health and Safety regulations. Always store and dispose of cleaning agents in accordance with site Health and Safety regulations.
2.
3.
4.
After CIP cleaning an additional sterilisation in place process (SIP) may be required when highly sensitive products are handled, inactivating any micro-organisms which might be still present in the pump. The sterilisation can be carried out be means of chemicals, hot water or steam. In the dairy industry the sterilisation temperature is approximately 145oC (293oF).
Compliance with International Standards and Guidelines
11. Compliance with International Standards and Guidelines

This section describes some of the international standards and guidelines applicable to Alfa Laval pump ranges.
In recent years there has been increasing concern over safety and hygiene in the bio-pharmaceutical and food industries. This has led to numerous standards and legislation being written.
A number of countries have national standards and/or directives applicable to food machinery but there are relatively few international standards. Those that exist are predominantly dairy based and are too general and developed on experience rather than scientific data. In the USA, a number of guidelines in the form of third party approval schemes have been developed for the dairy industry (3-A standards) and food service equipment (NSF National Sanitation Foundation). The structure of these schemes involves representatives of equipment manufacturers, end users and regulatory bodies in the implementation of recommendations. Unfortunately, however the 3-A standards have no benchmark of cleanability or test regimes to establish cleanability, and the NSF standards are not applicable to the hygienic design of general food processing equipment. Alfa Laval pump ranges are available to meet standards and legislation as follows: CE Compliance (Safety/Risk Assessment). 3-A Design and Material Specifications (Centrifugal and Positive Rotary Lobe Pumps for Milk and Milk Products). FDA Material Requirements. USDA Regulating Biotechnology. EN 10204 3.1.B Certified Material Traceability. EN 10204 2.2 Certificate of Conformity. EHEDG Cleanability and Installation Guidelines.
Fig. 11a CE
CE The introduction of CE marking is to demonstrate to interested parties that goods or equipment with this mark comply with the appropriate directives of the European Community. The appropriate directives are those that are concerned with the design and manufacture of goods or equipment. Directives are intended to facilitate a Single Market in the European Union. With emerging European standardisation, conflicting national standards will eventually tend to disappear, as all EU member states will work to the same standard, with a few exceptions. Some national differences cannot be harmonised. In Europe many different languages are spoken, and some parts are prone to earthquakes, high winds, heavy snow and extremes of cold and heat. It is often uneconomic to design equipment that will withstand all these conditions. All Alfa Laval pump ranges are CE marked and conform to the machinery directive 89/392/EEC as amended by 91/368/EEC, 93/ 44/EEC and 93/68/EEC and other relevant directives i.e. Electrical Equipment Low Voltage Directive 73/23/EEC and Electromagnetic Compatibility Directive 89/336/EEC. Other applicable standards/specifications which Alfa Laval pump ranges comply to are as follows: EN292 Parts 1 and 2: 1991 Safety of Machinery - Basic concepts, general principles for design. EN294: 1992 Safety distances to prevent danger zones being reached by the upper limbs. EN60204 Part 1: 1993 Safety of Machinery - Electrical equipment of machines - specification for general requirements. BS5304: 1988 Code of Practice for Safety of Machinery. ISO9001: 1994 Quality Management System.
Fig. 11b 3-A
3-A (Centrifugal and Positive Rotary Pumps for Milk and Milk Products) This standard has the purpose of establishing and documenting the material, fabrication, and installation (where appropriate) requirements for the engineering design and technical construction files for all products, assemblies, and sub-assemblies supplied by the manufacturer. The manufacturer has to be in compliance with the sanitary criteria found in 3-A Sanitary Standards or 3-A Accepted Practices. The 3-A Sanitary Standards and 3-A Accepted Practices are voluntarily applied as suitable sanitary criteria for dairy and food processing equipment. All Alfa Laval pump ranges conform to this 3-A standard. FDA The Food and Drug Administration (FDA) in the USA is the enforcement agency of the United States Government for food, drug and cosmetics manufacturing. It is responsible for new material approvals, plant inspections and material recalls. In the USA, the Food, Drug and Cosmetic Act requires food, drug and cosmetic manufacturers to prove that their products are safe. The FDAs primary purpose is to protect the public by enforcing this Act. The FDA can: approve plants for manufacturing. inspect plants at random. write general guidelines for good manufacturing processes. write specific criteria for materials in product contact. have certain expectations regarding design practices.
The FDA cannot: approve equipment outside of a particular use within a specific system. For all Alfa Laval pump ranges the product wetted parts can be made available with FDA compliance. approve materials for use in pharmaceutical systems. write specific engineering or design requirements for systems.
All Alfa Laval pump ranges can be supplied into process areas/plants that are controlled by USDA.
USDA The United States Department of Agriculture (USDA) is one of three Federal Agencies, along with the Environmental Protection Agency (EPA) and the U.S. Food and Drug Administration (FDA), primarily responsible for regulating biotechnology in the United States. Products are regulated according to their intended use, with some products being regulated under more than one agency. Agricultural biotechnology is a collection of scientific techniques, including genetic engineering, that are used to create, improve, or modify plants, animals, and micro-organisms. Using conventional techniques, such as selective breeding, scientists have been working to improve plants and animals for human benefit for hundreds of years. Modern techniques now enable scientists to move genes (and therefore desirable traits) in ways they could not before - and with greater ease and precision. The Federal government has a well co-ordinated system to ensure that new agricultural biotechnology products are safe for the environment and to animal and human health. While these agencies act independently, they have a close working relationship. USDAs Animal and Plant Health Inspection Service (APHIS) is responsible for protecting American agriculture against pests and diseases. The agency regulates the field testing of genetically engineered plants and certain micro-organisms. APHIS also approves and licenses veterinary biological substances, including animal vaccines that may be the product of biotechnology. USDAs Food Safety and Inspection Service (FSIS) ensures the safety of meat and poultry consumed as food. The Department of Health and Human Services Food and Drug Administration (FDA) governs the safety and labelling of drugs and the nations food and feed supply, excluding meat and poultry. The Environmental Protection Agency (EPA) ensures the safety and safe use of pesticidal and herbicidal substances in the environment and for certain industrial uses of microbes in the environment.
The Department of Health and Human Services National Institutes of Health have developed guidelines for the laboratory use of genetically engineered organisms. While these guidelines are generally voluntary, they are mandatory for any research conducted under Federal grants and they are widely followed by academic and industrial scientists around the world.
The Alfa Laval Rotary Lobe pump ranges and the LKH-UltraPure range of Centrifugal pumps can be supplied with material traceability if required.
EN 10204 3.1.B With the stringent demands of hygiene within new food and pharmaceutical plants being built, material traceability of equipment supplied is increasingly important. The EN 10204 standard defines the different types of inspection documents required for metallic products. In particular, 3.1.B of this standard refers to inspection documents being prepared at each stage of manufacture and supervised tests performed by authorised personnel independent of the manufacturer. EN 10204 2.2 This standard defines documents supplied to the purchaser, in accordance with the order requirements, for the supply of metallic products such as pumps. This takes the form of a certificate of conformity and can be applied to all Alfa Laval pump ranges. EHEDG We are now seeing increased public awareness surrounding food hygiene and food manufacturers desire to improve product safety. With no European Community legislation available the European Hygienic Equipment Design Group (EHEDG) was formed. EHEDG aims to promote hygiene during the processing and packaging of food products.
Fig. 11c EHEDG
EHEDG objectives are to produce hygienic design guidelines that can be verified by standard test procedures. This requires a range of test procedures for a variety of equipment parameters including cleanability, pasteurisability, sterilisability and aseptic capability.
The Alfa Laval LKH range of centrifugal pumps and the SX range of rotary lobe pumps with its dedicated vertical port orientation meet EHEDG cleanability and comply with EHEDG installation guidelines.
Installation Guide
12. Installation Guide

This section covers guidelines relating to pump installation, system design and pipework layout.
12.1 General
12.1.1 System Design
To ensure optimum pump operation it is important that any pump unit is installed correctly. When designing a pumping system the following should be taken into consideration: Confirm the Net Positive Suction Head (NPSH) available from the system exceeds the NPSH required by the pump, as this is crucial for ensuring the smooth operation of the pump and preventing cavitation. Avoid suction lifts and manifold/common suction lines for two rotary lobe pumps running in parallel, as this may cause vibration or cavitation (see fig. 12.1.1a).
Discharge line
Plan view Suction line Fig. 12.1.1a Avoid common suction lines
Protect the pump against blockage from hard solid objects e.g. nuts, bolts etc. Also protect the pump from accidental operation against a closed valve by using relief valves, pressure switches and current limiting devices. Fit suction and discharge pressure monitor points for diagnostic purposes. Fit valves, if two pumps are to be used on manifold/common discharge lines.
Installation Guide
Make the necessary piping arrangements if flushing is required for the seal or if a media is required for heating/cooling jackets. Adhere to installation foundation instructions. Do not subject rotary lobe pumps to rapid temperature changes, as pump seizure can result from thermal shock.
12.1.2 Pipework
All pipework must be supported. The pump must not be allowed to support any of the pipework weight and the following should be taken into consideration. Have short straight inlet pipework to reduce friction losses in the pipework thereby improving the NPSH available. Avoid bends, tees and any restrictions close to either suction or discharge side of pump. Use long radius bends wherever possible. Provide isolating valves on each side of the pump when necessary. Keep pipework horizontal where applicable to reduce air locks. Include eccentric reducers on suction lines.
12.1.3 Weight
The weight of the pump and drive unit should be considered for lifting gear requirements.
12.1.4 Electrical Supply

Ensure that there is an adequate electrical supply close to the pump drive unit. This should be compatible with the electric motor selected.
Installation Guide
12.2 Flow Direction

Outlet
12.2.1 Centrifugal Pumps

A centrifugal pump should never be operated in the wrong direction of rotation with fluid in the pump. It is possible to check this in two ways as follows:
Inlet
Fig. 12.2.1a Correct direction of flow
1. Pump with impeller screw fitted Start and stop the motor momentarily (without fluid in the pump). Ensure that the direction of rotation of the motor fan is clock-wise as viewed from the rear end of the motor.
Fig. 12.2.1b Pump with impeller screw fitted
2. Pump without impeller screw fitted With this method the impeller should always be removed before checking the direction of rotation. The pump should never be started if the impeller is fitted and the pump casing has been removed.
Fig. 12.2.1c Pump without impeller screw fitted
Start and stop the motor momentarily. Ensure that the direction of rotation of the stub shaft is anti-clockwise as viewed from the pump inlet.
Stub shaft
Fig. 12.2.1d Pump without impeller
Installation Guide
12.2.2 Rotary Lobe Pumps

The direction of flow is dictated by the direction of drive shaft rotation. Reversing the direction of rotation will reverse the flow direction.
Outlet
Inlet
Outlet
Inlet
Outlet
Outlet
Fig. 12.2.2a Flow direction
Inlet
Installation Guide
12.3 Baseplate Foundations (Rotary Lobe Pumps only)

Rotary Lobe pumps when supplied with a drive unit are normally mounted on a baseplate. Alfa Laval standard baseplates have pre-drilled fixing holes to accept base retaining bolts. To provide a permanent rigid support for securing the pump unit, a foundation is required which will also absorb vibration, strain or shock on the pumping unit. Methods of anchoring the baseplate to the foundation are varied, they can be studs embedded in the concrete either at the pouring stage as shown below, or by use of epoxy type grouts. Alternatively mechanical fixings can be used. The Foundation should be approximately 150mm longer and wider than the baseplate. The depth of the foundation should be proportional to the size of the complete pump unit. For example, a large pump unit foundation depth should be at least 20 times the diameter of the foundation bolts. The drawing below shows two typical methods for foundation bolt retaining. The sleeve allows for slight lateral movement of the bolts after the foundation is poured. Rag or waste paper can be used to prevent the concrete from entering the sleeve while the foundation is poured. A minimum of 14 days is normally required to allow the curing of the concrete prior to pump unit installation. D = Diameter of foundation bolts
Fig. 12.3b Foundations
Baseplate fixing holes
Fig. 12.3a Baseplate fixing
Installation Guide
12.4 Coupling Alignment (Rotary Lobe Pumps only)

Before rotary lobe pump units are installed it is important to ensure that the mounting surface is flat to avoid distortion of the baseplate. This will cause pump/motor shaft misalignment and pump/motor unit damage. Once the baseplate has been secured, the pump shaft to motor shaft coupling alignment should be checked and adjusted as necessary. This is achieved by checking the maximum angular and parallel allowable misalignments for the couplings as stated by the coupling manufacturers.
Parallel misalignment
Angular misalignment Fig. 12.4a Parallel and angular misalignment
12.5 Special Considerations for Liquid Ring Pumps

12.5.1 Pipework
The pipelines on the discharge side of a liquid ring pump should be routed as shown below to ensure correct pump operation.
Min. 1 m (3.3 ft)
Fig. 12.5.1a Installation of MR-166S/ -185S/-200S
Fig. 12.5.1b Installation of MR-300
Min. 2 m (6.6 ft)
Troubleshooting
13. Troubleshooting
This section offers possible causes and solutions to most common problems found in pump installation and operation.
13.1 General
In most pumping systems, pumps are likely to be the most vulnerable components. The symptoms frequently show the pump to be at fault regardless of what may be wrong. The problem is usually caused by inadequate control of the pumped fluid or a change in operating requirements of which the system or pump is not capable of handling or a component malfunction. Diagnosis of problems will be greatly assisted by having pressure gauges fitted to both pump inlet and outlet. Before starting to correctly identify the problem it is important to gather as much information relating to the process as follows: Reconfirm original duty conditions. What has changed in the process since operation was last satisfactory? i.e. pressure, temperature, fluid viscosity etc. Was the system undergoing routine maintenance? Were any new or repaired components omitted to be fitted? When was the pump last serviced? What was the appearance and condition of the pump internal components? How long did the pump operate before the problem? Any changes in pump noise or vibration?
The most common problems found are generally as follows and explained in 13.2: Loss of flow. Loss of suction. Low discharge pressure. Excessive noise or vibration. Excessive power usage. Rapid pump wear. Seal leakage.
Troubleshooting
13.2 Common Problems

13.2.1 Loss of Flow
A simple cause of this could be incorrect direction of shaft rotation, which although obvious is often overlooked. Loss of flow can be caused by excessive discharge pressure and/or by a change in fluid viscosity. In general terms: For a rotary lobe pump if the viscosity is significantly reduced, the pumps rated flow will be reduced, more so for higher pressure operation. For a centrifugal pump if the viscosity is increased, the pumps rated flow will be decreased.
13.2.2 Loss of Suction

Loss of suction can be minor, causing little short term damage or sufficiently major to cause catastrophic damage. Loss of suction means fluid is not reaching the pumping elements or not reaching them at a sufficiently high pressure to keep the fluid being pumped in a fluid state. Loss of suction can be interpreted as the inability to prime, cavitation or a gas content problem. The rotary lobe pump can be classed as self-priming. This means that within limits, it is capable of evacuating (pumping) a modest amount of air from the suction side of the pump to the discharge side of the pump. Filling the inlet system with fluid or at least filling the pump (wetted pumping elements) will make a major improvement in the pumps priming capability. The liquid ring pump can also be classed as self-priming when the pump casing is half filled with fluid and the LKHSP centrifugal pump range is specially designed to be self-priming. Cavitation is caused by insufficient system inlet pressure to the pump. This can be caused by an inlet system restriction, excessive fluid viscosity or excessive pump speed. Inlet restrictions can include dirty or clogged inlet strainers, debris floating in the fluid supply that covers the inlet piping intake, or rags. If the fluid is cooler than design temperature, its viscosity may be too high causing excessive friction (pressure loss) in the inlet piping system. Cavitation is frequently accompanied by noise, vibration and significant increase in discharge pressure pulsation. If a pump is allowed to cavitate over long periods this will cause damage to the pumphead components. The surface of these components are typically perforated and pitted.
Troubleshooting
Gas in the inlet pipework has the same impact on pump operation and creates the same symptoms as cavitation. This can occur under other circumstances such as a pump operating at an inlet pressure below local atmospheric pressure. In this instance it is quite likely that air is being drawn into the pipework through a loose pipe connection or pump casing joint, leaking inlet valve stem, defective or otherwise damaged joint gasket in the pipework system. In recirculating systems, such as a lubrication system where the fluid pumped is continuously returned to a supply source or tank, if the tank and return lines are not adequately designed, located and sized, air is easily entrained in the oil and immediately picked up by the pump inlet system. Be sure fluid level at its source is at or above minimum operating levels. Lines returning flow to a supply tank should terminate below minimum fluid level.
13.2.3 Low Discharge Pressure

Pump discharge pressure is caused only by the systems resistance to the flow provided by the pump. Either the pump is not providing the flow expected or the system is not offering the expected resistance to that flow. It is possible that flow is being restricted into the pump (cavitation), usually accompanied by noise and vibration, the pump is not producing its rated flow (pump worn or damaged), or the pump flow is bypassing rather than being delivered into the system as intended.
13.2.4 Excessive Noise or Vibration

Excessive noise and/or vibration can be a symptom of cavitation, mechanical damage to pump assembly, misalignment of drive or harmonics with other elements of the system. Cavitation is especially true if the discharge pressure is fluctuating or pulsating. Mechanical causes of noise and vibration include shaft misalignment, loose couplings, loose pump and/or driver mountings, loose pump and/or driver guards, worn or damaged driver or pump bearings or valve noise that seems to be coming from the pump. Valves, especially on the discharge side of the pump can sometimes go into a hydraulic vibration mode caused by operating pressure, flow rate and the valve design. Resetting or a change in an internal valve component is usually sufficient to solve the problem.
Troubleshooting
13.2.5 Excessive Power

Excessive power consumption can be caused by either mechanical or hydraulic problems. Mechanical causes include imminent bearing failure, pumping elements rubbing which can lead to a pump seizure and poor shaft alignments. Too high viscosity can result in the motor overloading. For a rotary lobe pump too high discharge pressure can cause the motor to overload. For a centrifugal pump too high capacity (too low discharge pressure) can cause the motor to overload.
13.2.6 Rapid Pump Wear

Rapid wear of pumphead components is either caused by abrasives being present in the fluid, chemical corrosion, loss of shaft support (bearing failure), or operation at a condition for which the pump is not suitable i.e. cavitation, excessively high pressure or high temperature. To avoid any abrasive foreign material entering the pump, strainers or filters should be employed wherever possible and practical. Rapid wear is sometimes not wear in the sense of a non-durable pump, but really a catastrophic pump failure that occurred very quickly. Looking at the pump internal parts alone may not provide much help in identifying the cause, thus the importance of knowing what was occurring in the time period immediately preceding detection of the problem.
13.2.7 Seal Leakage

Mechanical seals fitted to centrifugal, rotary lobe and liquid ring pumps can be seen as the weakest point for any pump leakage and special care should be taken to ensure the correct seal for the application is installed i.e. mounting attitude, seal face combination and elastomer selection. Apart from mis-selection and poor servicing, seal leakage can be due to pump cavitation, too high discharge pressure, being allowed to run dry and unexpected solids in the fluid.
Troubleshooting
13.3 Problem Solving Table

The table shown offers probable causes and solutions to the most common problems encountered. In ( ) next to the particular solution given you will find annotation relating to what pump type the solution is for. i.e. ce liq rlp = Centrifugal Pump = Liquid Ring Pump = Rotary Lobe Pump
See table 13.3a on the following pages:
Troubleshooting
Problem
No flow Under capacity Irregular discharge Low discharge pressure Pump will not prime Prime lost after starting Pump stalls when starting Pump overheats Motor overheats Excessive power absorbed Noise and vibration Pump element wear Syphoning Seizure Mechanical seal leakage Packed gland leakage
ce = Centrifugal, liq = Liquid Ring, rlp = Rotary Lobe
Probable Causes
Solutions
! ! ! ! ! !
Incorrect direction of rotation. Pump not primed. ! ! Insufficient NPSH available.
Reverse motor (ce, liq, rlp). Expel gas from suction line and pumping chamber and introduce fluid (ce, liq, rlp). Increase suction line diameter (ce, liq, rlp). Increase suction head (ce, liq, rlp). Simplify suction line configuration and reduce length (ce, liq, rlp). Reduce pump speed (rlp). Decrease fluid temperature (ce,liq) - check effect of
! ! !
Fluid vaporising in suction line.
increased viscosity? Increase suction line diameter (ce, liq, rlp). Increase suction head (ce, liq, rlp). Simplify suction line configuration and reduce length (ce, liq, rlp). Reduce pump speed (rlp). Decrease fluid temperature (ce, liq) - check effect of increased viscosity?
! ! ! ! ! !
! ! ! ! ! ! ! ! ! ! ! !
Air entering suction line. Strainer or filter blocked. !
Remake pipework joints (ce, rlp). Service fittings (ce, liq, rlp).
Fluid viscosity above rated figure. Increase fluid temperature (ce, liq, rlp). Decrease pump speed (rlp). Increase motor speed (ce, liq). Check seal face viscosity limitations (ce, liq, rlp).
! !
! ! ! ! ! !
Fluid viscosity below rated figure. Decrease fluid temperature (ce, liq, rlp). Increase pump speed (rlp). Fluid temp. above rated figure. Cool the pump casing (ce, rlp). Reduce fluid temperature (ce, liq, rlp). Check seal face and elastomer temperature limitations (ce, liq, rlp). ! ! ! ! ! ! ! Fluid temp. below rated figure. Unexpected solids in fluid. Heat the pump casing (ce,rlp). Increase fluid temperature (ce,liq, rlp). Clean the system (ce, liq, rlp). Fit strainer to suction line (ce, liq, rlp). If solids cannot be eliminated, consider fitting double mechanical seals (ce, rlp).
! ! !
! ! ! ! ! ! !
! ! ! Discharge pressure above rated figure.
Check for obstructions i.e. closed valve (ce, liq, rlp). Service system and change to prevent problem recurring (ce, liq, rlp). Simplify discharge line to decrease pressure
! ! !
Gland over-tightened.
(ce, liq, rlp). Slacken and re-adjust gland packing (rlp).
Troubleshooting
Problem
No flow Under capacity Irregular discharge Low discharge pressure Pump will not prime Prime lost after starting Pump stalls when starting Pump overheats Motor overheats Excessive power absorbed Noise and vibration Pump element wear Syphoning Seizure Mechanical seal leakage Packed gland leakage
ce = Centrifugal, liq = Liquid Ring, rlp = Rotary Lobe
Probable Causes
Solutions
! !
! Gland under-tightened. ! ! Seal flushing inadequate.
Adjust gland packing (rlp). Increase flush flow rate (ce,rlp). Check that flush fluid flows freely into seal area (ce, rlp). Decrease pump speed (rlp). Increase pump speed (rlp). Check alignment of pipes (ce, liq, rlp). Fit flexible pipes or expansion fittings (ce, liq, rlp). Support pipework (ce, liq, rlp). Check alignment and adjust mountings accordingly (rlp).
! ! ! !
! ! ! ! ! ! ! ! !
Pump speed above rated figure. Pump speed below rated figure. Pump casing strained by pipework.
! !
! !
Flexible coupling misaligned.
! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Insecure pump driver mountings. Fit lock washers to slack fasteners and re-tighten (rlp). Refer to pump maker for advice and replacement parts (rlp). Refer to pump makers instructions (rlp). Check rated and duty pressures (ce, liq, rlp). Refer to pump maker (ce, liq, rlp). Fit new components (ce, liq, rlp). Check pressure setting and re-adjust if necessary (rlp). Examine and clean seating surfaces (rlp). Replace worn parts (rlp).
! ! ! Shaft bearing wear or failure. ! ! Insufficient gearcase lubrication. Metal to metal contact of pumping element. Worn pumping element. Rotorcase cover relief valve leakage.
! ! ! ! ! !
! ! ! ! !
Rotorcase cover relief valve chatter. Rotorcase cover relief valve incorrectly set. Suction lift too high. ! ! Fluid pumped not compatible with materials used. No barrier in system to prevent
Check for wear on sealing surfaces, guides etc replace as necessary (rlp). Re-adjust spring compression (rlp) - valve should lift approx. 10% above duty pressure. Lower pump or raise fluid level (ce, rlp). Use optional materials (ce, liq, rlp). Ensure discharge pipework higher than suction tank
flow passing back through pump. (rlp). Ensure system operation prevents this (ce, rlp). ! ! Pump allowed to run dry. Fit single or double flushed mechanical seals (ce, rlp). Fit flushed packed gland (rlp). ! ! ! ! ! ! ! Table 13.3a Alfa Laval Pump Handbook 211 Faulty motor. Too large clearance between impeller and back plate/casing. Too small impeller diameter. Pumping element missing i.e. after service. Check and replace motor bearings (ce, liq, rlp). Reduce clearance between impeller and back plate/ casing (ce, liq). Fit larger size impeller - check motor size (ce). Fit pumping element (ce, liq, rlp).
Troubleshooting
Technical Data
14. Technical Data

This section includes a summary of nomenclature and formulas used in this handbook. Various conversion tables and curves are also shown.
14.1 Nomenclature
Symbol A D F fD g H Hs Ht hfs hft hs ht L n Pa Pf Ps Pt Pv Pvp Q Table 14.1a Description Area Tube diameter Force Darcy friction factor Gravity Total head Total suction head Total discharge head Pressure drop in suction line Pressure drop in discharge line Static suction head Static discharge head Tube length Pump speed Pressure absolute above fluid level Pressure loss due to friction Vacuum or pressure in a tank on suction side Pressure in a tank on discharge side Power/viscosity factor Vapour pressure Capacity Symbol QL q r Ra Re SG T V (Greek letter delta) (Greek letter eta) h m oa v (Greek letter mu) (Greek letter nu) (Greek letter rho) Description Fluid losses through impeller casing clearances Pump displacement Radius Surface roughness Reynolds number Specific gravity Shaft torque Fluid velocity
(Greek letter gamma) Specific weight Total (Greek letter epsilon) Relative roughness Total efficiency Hydraulic efficiency Mechanical efficiency Overall efficiency Volumetric efficiency Absolute viscosity Kinematic viscosity Fluid density
(Greek letter omega) Shaft angular velocity
Technical Data
14.2 Formulas
Designation Formula Comments Where to find
Product Viscosity
where: = Kinematic viscosity (mm2/s) = Absolute viscosity (mPa.s) = fluid density (kg/m3) or where: = Kinematic viscosity (cSt) = Absolute viscosity (cP) SG = specific gravity or 1 Poise = 100 cP 1 Stoke = 100 cSt
2.1.2
= SG
= x SG
Flow Velocity V=Q A where: V = fluid velocity (m/s) Q = capacity (m3/s) A = tube area (m2) or V = Q x 353.6 D2 where: V = fluid velocity (m/s) Q = capacity (m3/h) D = tube diameter (mm) or 2.1.7
V = Q x 0.409 D2
where: V = fluid velocity (ft/s) Q = capacity (US gall/min) D = tube diameter (in)
or
V = Q x 0.489 D2
where: V = fluid velocity (ft/s) Q = capacity (UK gall/min) D = tube diameter (in)
where: D = tube diameter (m) V = fluid velocity (m/s) = density (kg/m) = absolute viscosity (Pa.s) or where: D = tube diameter (mm) V = fluid velocity (m/s) = density (kg/m) = absolute viscosity (cP) or where: D = tube diameter (mm) Q = capacity (l/min) = absolute viscosity (cP) 2.1.7
Reynolds number (ratio of inertia forces to viscous forces)
Re = D x V x
Re = D x V x
Re = 21230 x Q Dx
Technical Data
Designation
Formula
Comments
Where to find
Reynolds number (ratio of inertia forces to viscous forces)
or
Re = 3162 x Q Dx
where: D = tube diameter (in) Q = capacity (US gall/min) = kinematic viscosity (cSt)
or
Re = 3800 x Q Dx
where: D = tube diameter (in) Q = capacity (UK gall/min) = kinematic viscosity (cSt)
Pressure/Head Pressure (total force per unit area exerted by a fluid) Static Pressure/Head (relationship between pressure and elevation) P=F A P=xgxh where: F = Force A = Area where: P = pressure/head (Pa) = fluid density (kg/m3) g = acceleration due to gravity (m/s2) h = height of fluid (m) or P = h x SG 10 or where: P = pressure/head (bar) h = height of fluid (m) 2.2.2
2.2.2
P = h x SG 2.31
where: P = pressure/head (psi) h = height of fluid (ft)

where: Ht = total discharge head Hs = total suction head where: ht = static discharge head hft = pressure drop in discharge line pt > 0 for pressure pt < 0 for vacuum pt = 0 for open tank where: hs = static suction head > 0 for flooded suction < 0 for suction lift hfs = pressure drop in suction line ps > 0 for pressure ps < 0 for vacuum ps = 0 for open tank where: Pf = friction loss (Pa) fD = friction factor (Darcy) L = tube length (m) V = fluid velocity (m/s) = fluid density (kg/m3) D = tube diameter (m) 2.2.2
Total head
H = Ht ( Hs)
Total discharge head
Ht = ht + hft + pt
2.2.2
Total suction head
Hs = hs - hfs + ( ps)
2.2.2
Friction loss (Miller equation)
Pf = fD x L x x V Dx2
2.2.2
Technical Data
Designation
Formula
Comments
Where to find
Friction loss (Miller equation)
or Pf = 5 x SG x fD x L x V D
where: Pf = friction loss (bar) fD = friction factor (Darcy) L = tube length (m) V = fluid velocity (m/s) SG = specific gravity D = tube diameter (mm)
or Pf = 0.0823 x SG x fD x L x V D
where: Pf = friction loss (psi) fD = friction factor (Darcy) L = tube length (ft) V = fluid velocity (ft/s) SG = specific gravity D = tube diameter (in)
where: fD = friction factor Re = Reynolds number where: Pa = pressure absolute above fluid level (bar) hs = static suction head (m) hfs = pressure drop in suction line (m) Pvp = vapour pressure (bar a) or where: Pa = pressure absolute above fluid level (psi) hs = static suction head (ft) hfs = pressure drop in suction line (ft) Pvp = vapour pressure (psia) 2.2.2
Darcy friction factor
fD = 64 Re
NPSHa (Net Positive Suction Head available)
NPSHa = Pa hs hfs Pvp (+hs for flooded suction) ( hs for suction lift)
2.2.4
Power Hydraulic power (theoretical energy required) Power (W) = Q x H x x g where: Q = capacity (m3/s) H = total head (m) = fluid density (kg/m3) g = acceleration due to gravity (m/s2) where: Q = capacity (l/min) H = total head (bar) k = 600 7.2.1
or Power (kW) = Q x H k
or Power (hp) = Q x H k
where: Q = capacity (US gall/min) H = total head (psi) k = 1715 where: Q = capacity (UK gall/min) H = total head (psi) k = 1428
or Power (hp) = Q x H k
Technical Data
Designation
Formula
Comments
Where to find 7.2.2
Required power (power needed at the pump shaft) Torque Torque
Hydraulic power Efficiency (100% = 1.0)
Torque (Nm) = Required power (kW) x 9550 Pump speed (rev/min) or Torque (Kgfm) = Required power (kW) x 974 Pump speed (rev/min) or Torque (ftlb) = Required power (hp) x 5250 Pump speed (rev/min)
7.2.3
Efficiency Hydraulic efficiency (h) Mechanical efficiency (m) Volumetric efficiency (Centrifugal and Liquid Ring pumps) Pump head loss (m) x 100% Total head (m)3 1 - Pump mech. losses x 100% Required power v = Q x 100% Q + QL where: v = volumetric efficiency Q = pump capacity QL = fluid losses due to leakage through the impeller casing clearances where: v = volumetric efficiency Q = pump capacity q = pump displacement 7.2.4
7.2.4
7.2.4
Volumetric efficiency (Rotary Lobe pumps)
v = Q x 100% q
7.2.4
Pump efficiency (p)
Water horse power x 100% Required power or p = Q x H x x g xT
7.2.4
where: p = pump efficiency Q = capacity (m3/s) H = total head/pressure (m) = fluid density (kg/m3) g = acceleration due to gravity (m/s2) = shaft angular velocity (rad/s) T = shaft torque (Nm) 7.2.4
Overall efficiency (oa)
Water horse power x 100% Drive power
Technical Data
Designation
Formula
Comments
Where to find
Pump speed - Rotary Lobe Pump Pump speed n = Q x 100 q x v x 60 where: n = pump speed (rev/min) Q = capacity (m/h) q = pump displacement (m/100 rev) v = vol. efficiency (100% = 1.0) or 7.2.4
n = Q x 100 q x v
where: n = pump speed (rev/min) Q = capacity (US gall/min) q = pump displacement (US gall/100 rev) v = vol. efficiency (100% = 1.0)
or
n = Q x 100 q x v
where: n = pump speed (rev/min) Q = capacity (UK gall/min) q = pump displacement (UK gall/100 rev) v = vol. efficiency (100% = 1.0)
Flow Control - Centrifugal Pump Connection between impeller diameter and capacity Connection between impeller diameter and head Connection between impeller diameter and power Reduction of multi-stage impeller diameter
D2 = D1 x
D2 = D1 x
D2 = D1 x

3 5
Q2 Q1 H2 H1 P2 P1 c-b a-b
where: D = impeller diameter (mm) Q = capacity (m/h) where: D = impeller diameter (mm) H = head (m) where: D = impeller diameter (mm) P = power (kW) where: D1 = standard diameter (mm) a = max. working point (m) b = min. working point (m) c = required working point (m) where: n = impeller speed (rev/min) Q = capacity (m/h)
7.3.2
7.3.2
7.3.2
D2 = D1 x
Q2 Q1
7.3.2
Connection between impeller speed and capacity Connection between impeller speed and head Connection between impeller speed and power Table 14.2a
7.3.2
n2 = n1 x
n2 = n1 x
n2 = n1 x
H2 H1 P2 P1
where: n = impeller speed (rev/min) H = head (m) where: n = impeller speed (rev/min) P = power (kW)
7.3.2
7.3.2
Technical Data
14.3 Conversion tables

14.3.1 Length
mm 1.0 1000 10 25.4 304.8 914.4 Table 14.3.1a m 0.001 1.0 0.01 0.0254 0.3048 0.9144 cm 0.10 100 1.0 2.540 30.48 91.441 in 0.0394 39.370 0.3937 1.0 12 36 ft 0.0033 3.2808 0.0328 0.0833 1.0 3.0 yd 0.0011 1.0936 0.1094 0.0278 0.3333 1.0
14.3.2 Volume
m 1.0 10 x 107 0.0010 1.64 x 10-5 00283 0.0045 37.88 x 10-4 Table 14.3.2a cm 100 x 10 1.0 1000 16.387 28317 4546.1 3785.4
4
l 1000 10 x 10-4 1.0 0.0164 28.317 4.546 3.7853
in 61024 0.0610 61.026 1.0 1728 277.42 231.0
ft 35.315 3.53 x 10-5 0.0353 58 x 10-5 1.0 0.1605 0.1337
UK gall. 220.0 22 x 10-5 0.22 0.0036 6.2288 1.0 0.8327
US gall. 264,0 26.4 x 10-5 0.2642 0.0043 7.4805 1.201 1.0
14.3.3 Volumetric Capacity

m/h 1.0 0.060 0.10 0.2727 0.2273 0.0283 101.94 3600 Table 14.3.3a l/min 16.667 1.0 1.6667 4.546 3.785 0.4719 1699 6 x 104 hl/h 10.0 0.60 1.0 2.7270 2.2732 0.2832 1019.4 36000 UK gall/min 3.6667 0.22 0.3667 1.0 0.8326 0.1038 373.73 13200 US gall/min 4.3999 0.2642 0.4399 1.201 1.0 0.1247 448.83 15838 ft/h 35.315 2.1189 3.5315 9.6326 8.0208 1.0 3600 127208 ft/s 9.81 x 10 5.88 x 10 9.81 x 10 2.67 x 10
-3 -4 -4 -3
m/s 2.78 x 10-4 1.67 x 10-5 2.78 x 10-5 7.57 x 10-5 6.31 x 10-5 7.86 x 10-6 0.0283 1.0
2.23 x 10-3 2.78 x 10-4 1.0 35.315
Technical Data
14.3.4 Mass Capacity

kg/s kg/h lb/h UK ton/h t/d (tonne/day) 86.40 0.024 0.0109 24.385 1.0 24 39.190 t/h (tonne/hour) 3.6 0.001 4.54 x 10-4 1.0160 0.0417 1.0 1.6350 lb/s
1.0 2.78 x 10-4 1.26 x 10-4 0.2822 11.57 x 10-3 0.2778 0.4536 Table 14.3.4a
3600 1.0 0.4536 1016.1 41.667 1000 1632.9
7936.6 2.2046 1.0 2240 91.859 2201.8 3600
3.5431 98.4 x 10-5 44.6 x 10-5 1.0 0.0410 0.9842 1.6071
2.2046 6.12 x 10-4 2.78 x 10-4 0.6222 0.0255 0.6116 1.0
14.3.5 Pressure/Head
bar kg/cm lb/in (psi) 14.504 14.223 1.0 14.696 0.4335 1.422 0.0193 0.4912 14.5 x 10-5 atm (water) 0.9869 0.9878 0.0609 1.0 0.0295 0.0968 13.2 x 10-4 0.0334 ft (water) 33.455 32.808 2.3067 33.889 1.0 3.2808 0.0446 1.1329 m mm Hg in Hg kPa
1.0 0.9807 0.0689 1.0133 0.0299 0.0981 13.3 x 10-4 0.0339 1.0 x 10-5 Table 14.3.5a
1.0197 1.0 0.0703 1.0332 0.0305 0.10 0.0014 0.0345 10.2 x 10-6
10.197 10 0.7031 10.332 0.3048 1.0 0.0136 0.3453 10.2 x 10-5
750.06 735.56 51.715 760.0 22.420 73.356 1.0 25.40 75.0 x 10-4
29.530 28.959 2.036 29.921 0.8827 2.896 0.0394 1,0 29.5 x 10-5
100 98.07 6.89 101.3 2.99 9.81 0.133 3.39 1.0
9.87 x 10-6 3.34 x 10-4
14.3.6 Force
Table 14.3.6a kN 1.0 9.81 x 10-3 44.5 x 10-4 kgf 101.97 1.0 0.4536 lbf 224.81 2.2046 1.0
14.3.7 Torque
Table 14.3.7a Nm 1.0 9.8067 1.3558 0.113 kgfm 0.102 1.0 0.1383 0.0115 lbft 0.7376 7.2330 1.0 0.0833 lbin 8.8508 86.796 12.0 1.0
Technical Data
14.3.8 Power
W 1.0 9.8067 1.3558 745.70 0.001 Table 14.3.8a kpm/s 0.102 1.0 0.1383 76.040 10.2 x 10-5 ft lbf/s 0.7376 7.2330 1.0 550.0 73.8 x 10-5 hp 1.34 x 10 0.0132 1.82 x 10-3 1.0 13.4 x 10-7
-3
kW 1000 9806.7 1355.8 74.6 x 10-4 1.0
14.3.9 Density
Table 14.3.9a kg/m3 1 103 27.680 x 10 16.019
3
g/cm3 10-3 1 27.680 16.019 x 10

-3
lb/in3 36.127 x 10-6 36.127 x 10-3 1 0.578 70 x 10

-3
lb/ft3 62.428 x 10-3 62.428 1.728 x 103 1
Technical Data
14.3.10 Viscosity Conversion Table

When SG = 1.0 Read Directly Across When SG is other than 1.0
Find cSt, then mutiply cSt x SG = cP Find Stoke, then mutiply Stoke x SG = Poise
cP 1 2 4 7 10 15 20 25 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 550 600 700 800 900 1000
Poise 0.01 0.02 0.04 0.07 0.10 0.15 0.20 0.25 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.5 6.0 7.0 8.0 9.0 10
cSt 1 2 4 7 10 15 20 25 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400 420 440 460 480 500 550 600 700 800 900 1000
Stoke 0.01 0.02 0.04 0.07 0.10 0.15 0.20 0.25 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.5 6.0 7.0 8.0 9.0 10
Saybolt Redwood Universal Seconds Standard SSU Engler #1 31 34 38 47 60 80 100 130 160 210 260 320 370 430 480 530 580 690 790 900 1000 1100 1200 1280 1380 1475 1530 1630 1730 1850 1950 2050 2160 2270 2380 2480 2660 2900 3380 3880 4300 4600 54 57 61 75 94 125 170 190 210 300 350 450 525 600 875 750 900 1050 1200 1350 1500 1650 1800 1950 2100 2250 2400 2550 2700 2850 3000 3150 3300 3450 3600 3750 4125 4500 5250 6000 8750 7500 29 32 36 44 52 63 86 112 138 181 225 270 314 364 405 445 492 585 670 762 817 933 1020 1085 1170 1250 1295 1380 1465 1570 1650 1740 1830 1925 2020 2100 2255 2460 2860 3290 3640 3900
Ford #3
Ford #4
Zahn #1
Zahn #2
Zahn #3
Zahn #4
Zahn #5
8 9 10 12 15 19 25 29 33 36 41 45 50 58 66 72 81 90 98 106 115 122 130 136 142 150 160 170 180 188 200 210 218 230 250 295 340 365 390
5 8 10 12 14 18 22 25 28 31 32 34 41 45 50 54 58 62 65 68 70 74 89 95 100 106 112 118 124 130 137 143 153 170 194 223 247 264
30 34 37 41 44 52 60 68 72 81 88
16 17 18 19 20 22 24 27 30 34 37 41 49 58 66 74 82 88
10 12 14 16 18 20 23 25 27 30 32 34 36 39 41 43 46 48 50 52 54 58 64 68 76
10 11 13 14 16 17 18 20 21 22 24 25 26 27 29 30 32 33 34 36 38 40 45 51 57 63 69
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 30 35 40 45 49
Technical Data
When SG = 1.0 Read Directly Across
When SG is other than 1.0

Find cSt, then mutiply cSt x SG = cP Find Stoke, then mutiply Stoke x SG = Poise
cP 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000 15000 20000 30000 40000 50000 60000 70000 80000 90000 100000 125000 150000 175000 200000
Poise 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 150 200 300 400 500 600 700 800 900 1000 1250 1500 1750 2000
cSt 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000 7500 8000 8500 9000 9500 10000 15000 20000 30000 40000 50000 60000 70000 80000 90000 100000 125000 150000 175000 200000
Stoke 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 150 200 300 400 500 600 700 800 900 1000 1250 1500 1750 2000
Saybolt Redwood Universal Seconds Standard SSU Engler #1 5200 5620 6100 6480 7000 7500 8000 8500 9000 9400 9850 10300 10750 11200 11600 14500 16500 18500 21000 23500 26000 28000 30000 32500 35000 37000 39500 41080 43000 46500 69400 92500 138500 185000 231000 277500 323500 370000 415500 462000 578000 694000 810000 925000 8250 9000 9750 10350 11100 11850 12600 13300 13900 14600 15300 16100 16800 17500 18250 21800 25200 28800 32400 36000 39600 43100 46000 49600 53200 56800 60300 63900 67400 71000 106000 140000 210000 276000 345000 414000 484000 550000 620000 689000 850000 4410 4680 5160 5490 5940 6350 6780 7200 7620 7950 8350 8730 9110 9500 9830 12300 14000 15650 17800 19900
Ford #3 445 480 520 550 595 635 680 720 760 800 835 875 910 950 985 1230 1400 1570
Ford #4 299 323 350 372 400 430 460 490 520 540 565 592 617 645 676 833 950 1060 1175 1350 1495 1605 1720 1870 2010 2120 2270 2350 2470 2670
Zahn #1
Zahn #2
Zahn #3
Zahn #4 77
Zahn #5 55 59 64 70 75 80 85 91 96
Table 14.3.10a
Technical Data
14.3.11 Temperature Conversion Table

Locate temperature in middle column. If in C read the F equivalent in the right hand column. If in F read C equivalent in the left hand column. C = ( F - 32 ) x 0.5556 F = ( C x 1.8 ) + 32 minus 459.4 - 0 C to F -273 -268 -262 -257 -251 -246 -240 -234 -229 -223 -218 -212 -207 -201 -196 -190 -184 -179 -173 -169 -168 -162 -157 -151 -146 -140 -134 -129 -123 -118 -112 -107 -101 -96 -90 -84 -79 -73 -68 -62 -57 -51 -46 -40 -34 -29 -23 -17.8 -459 -450 -440 -430 -420 -410 -400 -390 -380 -370 -360 -350 -340 -330 -320 -310 -300 -290 -280 -273 -270 -260 -250 -240 -230 -220 -210 -200 -190 -180 -170 -160 -150 -140 -130 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 C -17.8 -17.2 -16.7 -16.1 -15.6 -15.0 -14.4 -13.9 -13.3 -12.8 -12.2 -11.7 -11.1 -10.6 -10.0 -9.4 -8.9 -8.3 -7.8 -7.2 -6.7 -6.1 -5.6 -5.0 -4.4 -3.9 -3.3 -2.8 -2.2 -1.7 -1.1 -0.6 0.0 0.6 1.1 1.7 2.2 2.8 3.3 3.9 4.4 5.0 5.6 6.1 6.7 7.2 7.8 8.3 8.9 9.4 0 - 49 to 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 F 32 33.8 35.6 37.4 39.2 41.0 42.8 44.6 46.4 48.2 50.0 51.8 53.6 55.4 57.2 59.0 60.8 62.6 64.4 66.2 68.0 69.8 71.6 73.4 75.2 77.0 78.8 80.6 82.4 84.2 86.0 87.8 89.6 91.4 93.2 95.0 96.8 98.6 100.4 102.2 104.0 105.8 107.6 109.4 111.2 113.0 114.8 116.6 118.4 120.2 C 10.0 10.6 11.1 11.7 12.2 12.8 13.3 13.9 14.4 15.0 15.6 16.1 16.7 17.2 17.8 18.3 18.9 19.4 20.0 20.6 21.1 21.7 22.2 22.8 23.3 23.9 24.4 25.0 25.6 26.1 26,7 27.2 27.8 28.3 28.9 29.4 30.0 30.6 31.1 31.7 32.2 32.8 33.3 33.9 34.4 35.0 35.6 36.1 36.7 37.2 37.8 50 - 100 to 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 F 122.0 123.8 125.6 127.4 129.2 131.0 132.8 134.6 136.4 138.2 140.0 141.8 143.6 145.4 147.2 149.0 150.8 152.6 154.4 156.2 158.0 159.8 161.6 163.4 165.2 167.0 168.8 170.6 172.4 174.2 176.0 177.8 179.6 181.4 183.2 185.0 186.8 188.6 190.4 192.2 194.0 195.8 197.6 199.4 201.2 203.0 204.8 206.6 208.4 210.2 212.0 C 38 43 49 54 60 66 71 77 82 88 93 99 100 104 110 116 121 127 132 138 143 149 154 160 166 171 177 182 188 193 199 204 210 216 221 227 232 238 243 249 254 100 - 490 to 100 110 120 130 140 150 160 170 180 190 200 210 212 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430 440 450 460 470 480 490 F 212 230 248 266 284 302 320 338 356 374 392 410 414 428 446 464 482 500 518 536 554 572 590 608 626 644 662 680 698 716 734 752 770 788 806 824 842 860 878 896 914 C 260 266 271 277 282 288 293 299 304 310 316 321 327 332 338 343 349 354 360 366 371 377 382 388 393 399 404 410 416 421 427 432 438 443 449 454 460 466 471 477 482 488 493 499 504 510 516 521 527 532 538 500 - 1000 to F 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850 860 870 880 890 900 910 920 930 940 950 960 970 980 990 1000 932 950 968 986 1004 1022 1040 1058 1076 1094 1112 1130 1148 1166 1184 1202 1220 1238 1256 1274 1292 1310 1328 1346 1364 1382 1400 1418 1436 1454 1472 1490 1508 1526 1544 1562 1580 1598 1616 1634 1652 1670 1688 1706 1724 1742 1760 1778 1796 1814 1832
-459.4 -454 -436 -418 -400 -382 -364 -346 -328 -310 -292 -274 -256 -238 -220 -202 -184 -166 -148 -130 -112 -94 -76 -58 -40 -22 -4 14 32
Table 14.3.11a 224 Alfa Laval Pump Handbook
Technical Data
14.4 Water Vapour Pressure Table

Table 14.4a Temp. (C) 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Density () (kg/m3) 999.8 1000.0 999.7 999.1 998.2 997.1 995.7 994.1 992.2 990.2 988.0 985.7 983.2 980.6 977.8 974.9 971.8 968.6 965.3 961.9 958.4 Vapour pressure (Pvp) (kPa) 0.61 0.87 1.23 1.71 2.33 3.40 4.25 5.62 7.38 9.60 12.3 15.7 19.9 25.1 31.2 38.6 47.5 57.9 70.1 84.7 101.3
Vapour pressure: 1 bar = 100 kPa = 105 N/m2
Technical Data
14.5 Pressure Drop Curve for 100 m ISO/DIN Tube
1 bar 10 m (metre liquid column)
Fig. 14.5a Pressure Drop Curve
Technical Data
14.6 Velocity (m/s) in ISO and DIN Tubes at various Capacities

m/s
l/h
0 20000 40000 60000 80000 100000 120000 140000 160000 180000 200000
1 m3/h = 1000 l/h

Fig. 14.6a Connection between velocity and capacity at different tube dimensions
Technical Data
14.7 Equivalent Tube Length Table

14.7.1 ISO Tube Metric
Equipment for ISO tube (for water at 2 m/s) Seat valves 1. SRC, SMO 2. 3. 4. 5. 6. 1. SRC-LS 2. 3. 4. 5. 6. Aseptic seat valves 1. ARC, AMO 2. 3. 4. 5. 6. 1. ARC-SB 2. 3. 4. Other valves Non-return valve LKC-2 Butterfly valve LKB 1. Koltek MH 2. 7 1 1 1 10 1 2 2 12 1 3 4 21 1 5 6 20 2 6 9 26 2 7 10 7 5 4 4 6 5 8 8 6 8 13 9 10 8 18 15 15 15 10 17 28 21 20 15 37 28 20 20 18 44 43 27 32 29 61 50 55 36 55 39 88 75 7 5 4 3 5 5 6 4 10 4 14 10 7 3 7 5 8 7 12 6 12 7 27 21 12 8 8 4 13 10 21 14 15 12 32 22 11 7 9 6 13 11 30 19 29 26 50 39 8 6 14 11 19 17 25 mm Equivalent tube length in metres per unit 38 mm 51 mm 63.5 mm 76 mm 101.6 mm
Technical Data
Equipment for ISO tube (for water at 2 m/s) Mixproof valves 1. Unique * 2. 3. 4. 1. SMP-SC 2. 3. 4. 1. SMP-SC, 3-body 2. 1. SMP-BC 2. 3. 4. 5. 6. 7. 1. SMP-BCA 2. 3. 4. 5. 6. 7. 1. SMP-TO 2. 3. Tubes and fittings Bend 90 deg. Bend 45 deg. Tee (out through side port) Tee (in through side port)
25 mm
Equivalent tube length in metres per unit 38 mm 51 mm 63.5 mm 76 mm
101.6 mm
14 14 5 6
14 14 4 5 14 14 4 4 8 8
27 27 6 7 17 16 4 5 14 16 4 11 7 13 13 34 34 4 18 16 30 20 41 34 5 8 5
25 25 5 7 32 25 5 5 27 29 3 8 7 15 14 25 23 3 29 29 41 27 41 38
26 26 4 5 55 41 5 14 45 52 6 18 11 32 31 101 101 6 84 81 104 75 152 146 6 23 24
3 3 3 7 6 9 6 2 5 3 6 5 5 6
3 6 5 11 10 12 12 3 10 9 18 12 14 14
0.3 0.2 1 1
1 0.4 2 2
1 1 3 2
1 1 4 3
1 1 5 4
2 1 7 5 Table 14.7.1a
* Pressure drop/equivalent tube length is for unbalanced upper plug and balanced lower plug. For other combinations use the CAS Unique configuration tool.
Technical Data
14.7.2 ISO Tube Feet

Equipment for ISO tube (for water at 6 ft/s) Seat valves 1. SRC, SMO 2. 3. 4. 5. 6. 1. SRC-LS 2. 3. 4. 5. 6. Seat valves 1. ARC, AMO 2. 3. 4. 5. 6. 1. ARC-SB 2. 3. 4. Other valves Non-return valve LKC-2 Butterfly valve LKB 1. Koltek MH 2. 23 3 3 3 33 3 7 7 39 3 10 13 69 3 16 20 66 7 20 30 85 7 23 33 23 16 13 13 20 16 26 26 20 26 43 30 33 26 59 49 49 49 33 56 92 69 66 49 121 92 66 66 59 144 141 89 105 95 200 164 180 118 180 128 289 246 23 16 13 10 16 16 20 13 33 13 46 33 23 10 23 16 26 23 39 20 39 23 89 69 39 26 26 13 43 33 69 46 49 39 105 72 36 23 30 20 43 36 98 62 95 85 164 128 26 20 46 36 62 56 1 in 1.5 in Equivalent tube length in feet per unit 2 in 2.5 in 3 in 4 in
Technical Data
Equipment for ISO tube (for water at 6 ft/s) Mixproof valves 1. Unique * 2. 3. 4. 1. SMP-SC 2. 3. 4. 1. SMP-SC, 3-body 2. 1. SMP-BC 2. 3. 4. 5. 6. 7. 1. SMP-BCA 2. 3. 4. 5. 6. 7. 1. SMP-TO 2. 3. Tubes and fittings Bend 90 deg. Bend 45 deg. Tee (out through side port) Tee (in through side port)
1 in
1.5 in
Equivalent tube length in feet per unit 2 in 2.5 in 3 in
4 in
46 46 16 20
46 46 13 16 46 46 13 13 26 26
89 89 20 23 56 52 13 16 46 52 13 36 23 43 43 112 112 13 59 52 98 66 135 112 16 26 16
82 82 16 23 105 82 16 16 89 95 10 26 23 49 46 82 75 10 95 95 135 89 135 125
85 85 13 16 180 135 16 46 148 171 20 59 36 105 102 331 331 20 276 266 341 246 499 479 20 75 79
10 10 10 23 20 30 20 7 16 10 20 16 16 20
10 20 16 36 33 39 39 10 33 30 59 39 46 46
1 1 3 3
3 1 7 7
3 3 10 7
3 3 13 10
3 3 16 13
7 3 23 16
Table 14.7.2a
Technical Data
14.7.3 DIN Tube Metric

Equipment for DIN tube (for water at 2 m/s) Seat valves 1. SRC, SMO 2. 3. 4. 5. 6. 1. SRC-LS 2. 3. 4. 5. 6. Aseptic seat valves 1. ARC, AMO 2. 3. 4. 5. 6. 1. ARC-SB 2. 3. 4. Other valves Non-return valve LKC-2 Butterfly valve LKB 1. Koltek MH 2. 14 2 2 2 14 1 2 2 15 1 5 5 32 2 9 9 36 2 10 14 30 2 8 13 2 1 8 6 5 5 7 6 10 10 6 9 15 11 13 9 20 17 21 21 11 21 42 28 26 22 54 40 34 34 24 64 64 44 46 44 98 77 64 40 57 43 94 84 8 6 4 4 6 6 7 6 11 6 18 15 9 4 9 8 11 10 15 9 18 12 44 34 19 10 13 7 19 16 28 21 27 23 54 36 21 14 18 12 24 22 33 23 33 28 57 43 9 7 17 13 22 18 18 22 29 27 49 38 44 72 72 69 150 89 DN25 DN40 Equivalent tube length in metres per unit DN50 DN65 DN80 DN100 DN125 DN150
Technical Data
Equipment for DIN tube (for water at 2 m/s) Mixproof valves 1. Unique * 2. 3. 4. 1. SMP-SC 2. 3. 4. 1. SMP-SC, 3-body 2. 1. SMP-BC 2. 3. 4. 5. 6. 7. 1. SMP-BCA 2. 3. 4. 5. 6. 7. 1. SMP-TO 2. 3. Tubes and fittings Bend 90 deg. Bend 45 deg. Tee (out through side port) Tee (in through side port)
DN25
DN40
Equivalent tube length in metres per unit DN50 DN65 DN80 DN100
DN125
DN150
14 14 5 6
14 14 4 5 15 14 4 4 9 9
27 27 6 7 24 22 6 6 22 25 5 13 11 22 22 52 52 5 32 25 46 30 62 54 7 11 8
25 25 5 7 54 41 6 6 44 54 5 15 12 24 23 44 44 5 51 49 72 46 67 64
26 26 4 5 64 50 6 15 54 64 7 21 20 40 37 114 114 6 97 94 124 84 174 167 8 28 30 4 38 31 8 78 61 49 53 7 7 89 133 22 22
3 4 4 9 7 10 9 3 6 3 9 6 8 9
4 7 6 17 13 15 15 4 13 12 24 15 20 21
0.3 0.2 1 1
1 0.4 2 2
1 1 3 2
1 1 4 3
1 1 5 4
2 1 7 5 Table 14.7.3a
Technical Data
14.7.4 DIN Tube Feet

Equipment for DIN tube (for water at 6 ft/s) Seat valves 1. SRC, SMO 2. 3. 4. 5. 6. 1. SRC-LS 2. 3. 4. 5. 6. Aseptic seat valves 1. ARC, AMO 2. 3. 4. 5. 6. 1. ARC-SB 2. 3. 4. Other valves Non-return valve LKC-2 Butterfly valve LKB 1. Koltek MH 2. 46 7 7 7 46 3 7 7 49 3 16 16 105 7 30 30 118 7 33 46 98 7 26 43 7 3 26 20 16 16 30 20 33 33 20 30 49 36 43 30 66 56 69 69 36 69 138 92 85 72 177 131 112 112 79 210 210 144 151 144 322 253 210 131 187 141 308 276 26 20 13 13 20 20 23 20 36 20 59 49 30 13 30 26 36 33 49 30 59 39 144 112 62 33 43 23 62 52 92 69 89 75 177 118 69 46 59 39 79 72 108 75 108 92 187 141 30 23 56 43 72 59 59 72 95 89 161 125 144 236 236 226 492 292 1 in 1.5 in Equivalent tube length in feet per unit 2 in 2.5 in 3 in 4 in 5 in 6 in
Technical Data
Equipment for DIN tube (for water at 6 ft/s) Mixproof valves 1. Unique * 2. 3. 4. 1. SMP-SC 2. 3. 4. 1. SMP-SC, 3-body 2. 1. SMP-BC 2. 3. 4. 5. 6. 7. 1. SMP-BCA 2. 3. 4. 5. 6. 7. 1. SMP-TO 2. 3. Tubes and fittings Bend 90 deg. Bend 45 deg. Tee (out through side port) Tee (in through side port)
1 in
1.5 in
Equivalent tube length in feet per unit 2 in 2.5 in 3 in 4 in
5 in
6 in
46 46 16 20
46 46 13 16 49 46 13 13 30 30
89 89 20 23 79 72 20 20 72 82 16 43 36 72 72 171 171 16 105 82 151 98 203 177 23 36 26
82 82 16 23 177 135 20 20 144 177 16 49 39 79 75 144 144 16 167 161 236 151 220 210
85 85 13 16 210 164 20 49 177 210 23 69 66 131 121 374 374 20 318 308 407 276 571 548 26 92 98 13 125 102 26 256 200 161 174 23 23 292 436 72 72
10 13 13 30 23 33 30 10 20 10 30 20 26 30
13 23 20 56 43 49 49 13 43 39 79 49 66 69
1 1 3 3
3 1 7 7
3 3 10 7
3 3 13 10
3 3 16 13
7 3 23 16
Table 14.7.4a
Technical Data
14.8 Moody Diagram
Fig. 14.8a Moody diagram for fD (after Miller) 236 Alfa Laval Pump Handbook
Technical Data
14.9 Initial Suction Line Sizing
Flow rate - m3/h
100
Fig. 14.9a Initial suction line sizing
Viscosity - cSt
Technical Data
14.10 Elastomer Compatibility Guide

Listed below are fluids commonly pumped. The elastomer compatibilty is for guidance purposes only as this may be affected by temperature. The fluid viscous behaviour type shown relates to general terms - in some instances Pseudoplastic fluids can have Thixotropic tendencies. () - Fluid can become Dilatant at high concentration and high shear rate. - If low concentration, this can be Newtonian.
NBR ACETIC ACID ACETONE ADHESIVE - SOLVENT BASED ADHESIVE - WATER BASED ALUM SLUDGE AMMONIUM HYDROXIDE ANIMAL FAT BABY BATH BABY LOTION BABY OIL BATH FOAM BATTER BEER BENTONITE SUSPENSION BISCUIT CREAM BISULPHITE BITUMEN BLACK LIQUOR BLEACH BLOOD BODY LOTION BODY SCRUB BRINE BUTTER CALCIUM CARBONATE SLURRY CARAMEL - COLOURING CARAMEL - TOFFEE CASTOR OIL CELLULOSE ACETATE DOPE CELLULOSE SUSPENSION CERAMIC SLIP ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Elastomer Material EPDM FPM ! ! Viscous Behaviour Type PTFE ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Newtonian Pseudoplastic () Pseudoplastic Newtonian Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Pseudoplastic ()
()
Name of Fluid Pumped
Technical Data
Name of Fluid Pumped NBR CHEESE CHEWING GUM CHINA CLAY SLURRY CHOCOLATE CHROMIC ACID CHUTNEY CITRIC ACID COAL TAR COCOA BUTTER COCOA LIQUOR COCONUT CREAM COLLAGEN GEL CONDENSED MILK COPPER SULPHATE CORN STEEP LIQUOR CORN SYRUP COSMETIC CREAM COUGH SYRUP CRUDE OIL CUSTARD DAIRY CREAM DETERGENT - AMPHOTERIC DETERGENT - ANIONIC DETERGENT - CATIONIC DETERGENT - NONIONIC DIESEL OIL DODECYL BENZENE SULPHONIC ACID DRILLING MUD DYE EGG ENZYME SOLUTION ETHANOL ETHYLENE GLYCOL FABRIC CONDITIONER FATS FATTY ACID FERRIC CHLORIDE FERTILISER FILTER AID FININGS FIRE FIGHTING FOAM FISH OIL FONDANT FORMIC ACID FROMAGE FRAIS FRUCTOSE FRUIT JUICE CONCENTRATE FRUIT PUREE ! ! ! ! ! ! ! ! ! ! !
Elastomer Material EPDM FPM ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Viscous Behaviour Type PTFE ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Pseudoplastic Pseudoplastic Pseudoplastic () Pseudoplastic Newtonian Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Pseudoplastic () Newtonian Newtonian Newtonian Newtonian Pseudoplastic Newtonian Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Newtonian Pseudoplastic Newtonian Pseudoplastic Pseudoplastic
Technical Data
Name of Fluid Pumped NBR FUDGE GELATINE GLUCOSE GLYCERINE GREASE GYPSUM SLURRY HAIR CONDITIONER HAIR GEL HAND CLEANSER HONEY HYDROCHLORIC ACID HYDROGEN PEROXIDE ICE CREAM MIX INK - PRINTING INK - WATER BASED ISOBUTYL ALCOHOL ISOCYANATE ISOPROPANOL JAM KEROSENE LACTIC ACID LACTOSE LANOLIN LATEX LECITHIN LIPSTICK LIQUORICE MAGMA MAIZE STARCH SLURRY MALT EXTRACT MANGANESE NITRATE MASCARA MASHED POTATO MASSECUITE MAYONNAISE MEAT PASTE METHANOL METHYL ETHYL KETONE SOLVENT METHYLATED SPIRIT METHYLENE CHLORIDE MILK MINCEMEAT MINERAL OIL MOLASSES MUSTARD NEAT SOAP NITRIC ACID PAINTS - SOLVENT BASED ! ! ! ! ! ! ! !
Elastomer Material EPDM FPM ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Viscous Behaviour Type PTFE ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Pseudoplastic Pseudoplastic Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Pseudoplastic Pseudoplastic Newtonian Newtonian Newtonian Newtonian Pseudoplastic Newtonian Newtonian Newtonian Newtonian Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Newtonian Newtonian Newtonian Pseudoplastic Newtonian Newtonian Pseudoplastic Pseudoplastic Newtonian Pseudoplastic
Technical Data
Name of Fluid Pumped NBR PAINTS - WATER BASED PAPER COATING - CLAY PAPER COATING - PIGMENT PAPER COATING - STARCH PAPER PULP PEANUT BUTTER PERACETIC ACID PETFOOD PETROLEUM PHOSPHORIC ACID PHOTOGRAPHIC EMULSION PLASTISOL POLYETHYLENE GLYCOL POLYVINYL ALCOHOL POTASSIUM HYDROXIDE PROPIONIC ACID PROPYLENE GLYCOL QUARG RESIN RUBBER SOLUTION SAUCE - CONFECTIONERY SAUCE - VEGETABLE SAUSAGE MEAT SEWAGE SLUDGE SHAMPOO SHAVING CREAM SILICONE OIL SODIUM HYDROXIDE SODIUM SILICATE SORBIC ACID SORBITOL STARCH SUGAR PULP - BEET SUGAR PULP - CANE SUGAR SYRUP SULPHURIC ACID TALL OIL TALLOW TITANIUM DIOXIDE TOBACCO FLAVOURING TOLUENE TOMATO KETCHUP TOMATO PUREE TOOTHPASTE TRUB UREA VARNISH VASELINE ! ! ! ! ! ! ! ! ! ! ! !
Elastomer Material EPDM FPM ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Viscous Behaviour Type PTFE ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Pseudoplastic Pseudoplastic () Pseudoplastic () Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Pseudoplastic Newtonian Newtonian Pseudoplastic Newtonian Newtonian Pseudoplastic Newtonian Newtonian Newtonian Pseudoplastic Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Newtonian Newtonian Pseudoplastic () Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic Pseudoplastic Newtonian Newtonian Pseudoplastic
Technical Data
Name of Fluid Pumped NBR VEGETABLE GUM VEGETABLE OIL VITAMIN SOLUTION WATER WAX WHEY WHITE SPIRIT WINE WORT XYLENE YEAST YOGHURT ZEOLITE SLURRY ZIRCONIA SLURRY Table 14.10a Elastomer compatibility guide ! ! !
Elastomer Material EPDM FPM ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !
Viscous Behaviour Type PTFE ! ! ! ! ! ! ! ! ! ! ! ! ! ! Pseudoplastic Newtonian Newtonian Newtonian Newtonian Newtonian Newtonian Newtonian Newtonian Newtonian Pseudoplastic Pseudoplastic Pseudoplastic () Pseudoplastic ()
Technical Data
14.11 Changing Motor Name Plates

Manufacturer Frame Size Output Power kW Frequency Hz Supply Voltage V Motor Nameplate Rated Speed rev/min Power Factor Rated Current A
2-pole motors ABB 71 C 0.55 0.55 0.65 0.55 0.55 0.75 0.75 0.90 0.75 0.75 0.75 0.75 1.1 1.1 1.3 1.1 1.1 1.1 1.1 1.5 1.5 1.75 1.5 1.6 1.6 1.6 2.2 2.2 2.5 2.1 2.3 2.3 2.3 3.0 3.0 3.5 3.0 3.2 3.2 3.2 3.0 3.5 3.2 3.2 50 50 60 60 60 50 50 60 60 60 60 60 50 50 60 60 60 60 60 50 50 60 60 60 60 60 50 50 60 60 60 60 60 50 50 60 60 60 60 60 50 60 60 60 220-240/380-420Y 200 250-280/380-480Y 200 220 220-240/380-420Y 200 250-280/440-480Y 200 220 400Y 380Y 220-240/380-420Y 200 250-280/440-480Y 200 220 400Y 380Y 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 Standard New Standard New New Standard New Standard New New New New Standard New Standard New New New New Standard New Standard New New New New Standard New Standard New New New New Standard New Standard New New New New Standard Standard New New 2850 2800 3420 3360 3410 2850 2800 3420 3370 3420 3440 3420 2850 2830 3420 3390 3440 3450 3440 2920 2880 3510 3460 3490 3500 3490 2900 2860 3500 3430 3470 3470 3450 2920 2890 3520 3470 3490 3500 3490 2920 3520 3500 3490 0.74 0.89 0.77 0.90 0.88 0.82 0.91 0.86 0.92 0.91 0.90 0.91 0.85 0.91 0.89 0.92 0.91 0.90 0.91 0.85 0.89 0.85 0.91 0.89 0.88 0.89 0.85 0.90 0.86 0.91 0.90 0.90 0.91 0.88 0.91 0.88 0.92 0.91 0.91 0.91 0.87 0.88 0.91 0.91 2.6/1.5 2.4 2.6/1.5 2.3 2.1 3.1/1.8 3.3 3.0/0.7 3.1 2.8 1.6 1.6 4.0/2.3 4.5 3.6/2.1 4.3 4.0 2.2 2.3 5.4/3.2 6.0 3.1 5.9 5.4 3.0 3.1 8.1/4.7 8.7 4.4 8.3 7.5 4.5 4.8 9.9/5.7 11.0 5.7 10.9 10.5 5.8 6.1 5.7/3.3 5.7 5.8 6.1
ABB
80 A
ABB
80 C
ABB
90 L
ABB
90 LB
ABB
100 LB
Technical Data
Manufacturer
Frame Size
Output Power kW
Frequency Hz
Supply Voltage V
Motor Nameplate
Rated Speed rev/min
Power Factor
Rated Current A
2-pole motors ABB 112 M 4.0 3.7 4.6 3.4 3.8 4.0 3.8 4.0 4.6 4.0 3.8 ABB 132 SA 5.5 5.4 6.4 5.4 5.4 5.7 5.4 5.5 6.4 5.7 5.4 ABB 132 SB 7.5 6.6 8.6 7.0 7.4 7.8 7.4 7.5 8.6 7.8 7.4 ABB 160 MA 11.0 11.0 12.5 11.0 12.2 12.5 12.2 11.0 12.5 12.5 12.2 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New 2850 2790 3450 3360 3390 3400 3390 2850 3450 3400 3390 2855 2790 3455 3345 3395 3380 3370 2855 3455 3380 3370 2855 2825 3455 3365 3405 3415 3405 2855 3455 3415 3405 2930 2900 3515 3475 3485 3500 3485 2930 3515 3500 3485 0.91 0.92 0.91 0.92 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.88 0.90 0.88 0.91 0.89 0.89 0.89 0.88 0.88 0.89 0.89 0.90 0.91 0.90 0.92 0.91 0.91 0.91 0.90 0.90 0.91 0.91 0.88 0.89 0.89 0.89 0.89 0.89 0.89 0.88 0.89 0.89 0.89 13.5/7.8 14.5 7.7 13.1 13.3 7.4 7.7 7.8/4.5 7.7 7.4 7.7 18.9/10.9 21.0 10.9 21.0 18.8 10.9 10.9 10.9/6.3 10.9 10.9 10.9 25.5/14.7 25.0 14.4 26.0 25.0 14.4 14.4 14.7/8.5 14.4 14.4 14.4 34.5/20.0 40.0 20.0 40.0 40.0 22.0 23.0 20.0/11.5 20.0 22.0 23.0
Technical Data
Manufacturer
Frame Size
Output Power kW
Frequency Hz
Supply Voltage V
Motor Nameplate
Rated Speed rev/min
Power Factor
Rated Current A
2-pole motors ABB 160M 15.0 14.5 17.0 14.0 15.7 16.5 15.7 15.0 17.0 16.5 15.7 ABB 160 L 18.5 17.2 21.0 16.7 18.5 19.4 18.5 18.5 21.0 19.4 18.5 ABB 180 M 22.0 22.0 25.0 22.0 25.0 25.0 25.0 22.0 25.0 25.0 25.0 4-pole motors ABB 90 L-4 1.5 1.5 1.75 1.5 1.6 1.75 1.75 50 50 60 60 60 60 60 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y Standard New Standard New New New New 1440 1380 1730 1660 1680 1680 1660 0.74 0.86 0.76 0.87 0.86 0.86 0.87 6.2/3.6 6.3 3.5 6.2 6.1 3.6 3.8 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New 2920 2890 3505 3470 3485 3500 3485 2920 3505 3500 3485 2920 2895 3510 3500 3490 3500 3490 2920 3510 3500 3490 2930 2920 3530 3505 3510 3520 3510 2930 3530 3520 3510 0.9 0.9 0.9 0.9 0.89 0.89 0.89 0.9 0.9 0.89 0.89 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.91 0.89 0.90 0.90 0.91 0.89 0.88 0.89 0.89 0.90 0.88 0.89 46.0/26.5 53.0 27.5 51.0 52.0 30.0 30.0 26.5/15.3 27.5 30.0 30.0 55.0/32.0 60.0 33.5 59.0 59.0 34.0 34.0 32.0/18.5 33.5 34.0 34.0 67.0/38.5 77.0 40.5 76.0 80.0 44.0 46.0 38.5/22.0 40.5 44.0 46.0
Technical Data
Manufacturer
Frame Size
Output Power kW
Frequency Hz
Supply Voltage V
Motor Nameplate
Rated Speed rev/min
Power Factor
Rated Current A
4-pole motors ABB 132 S-4 5.5 5.3 6.4 5.5 6.0 6.3 6.0 5.5 6.4 6.3 6.0 ABB 132 M-4 7.5 6.8 8.6 7.4 8.0 8.4 8.0 7.5 8.6 8.4 8.0 ABB 160 L-4 15.0 14.0 17.0 14.0 16.0 16.8 16.0 15.0 17.0 16.8 16.0 ABB 180M-4 18.5 18.5 21.0 18.5 20.5 21.0 20.5 18.5 21.0 21.0 20.5 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 50 50 60 60 60 60 60 50 60 60 60 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 220-240/380-420Y 200 440-480Y 200 220 400Y 380Y 380-420/660-690Y 440-480 400 380 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 230/400Y 200 440Y 200 220 400Y 380Y 400/690Y 440 400 380 Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New Standard New Standard New New New New Standard Standard New New 1440 1430 1750 1700 1730 1735 1730 1450 1750 1735 1730 1450 1440 1750 1720 1730 1735 1730 1450 1750 1735 1730 1455 1440 1745 1720 1730 1735 1730 1455 1765 1735 1730 1470 1460 1765 1750 1755 1755 1755 1470 1765 1755 1755 0.83 0.86 0.83 0.86 0.86 0.86 0.86 0.83 0.83 0.86 0.86 0.83 0.86 0.83 0.87 0.87 0.87 0.87 0.83 0.83 0.87 0.87 0.84 0.86 0.84 0.85 0.85 0.85 0.85 0.84 0.84 0.85 0.85 0.84 0.85 0.85 0.84 0.85 0.85 0.85 0.84 0.85 0.85 0.85 19.9/11.5 21.1 11.5 22.0 21.5 12.4 12.4 11.5/6.6 11.5 12.4 12.4 27.0/15.3 26.3 15.1 29.0 28.0 16.2 16.2 15.3/8.8 15.1 16.2 16.2 49.0/28.5 53.0 30.0 54.0 55.0 32.0 32.0 28.5/16.5 30.0 32.0 32.0 61.0/35.0 70.0 36.0 71.0 70.0 41.0 40.0 35.0/20.0 36.0 41.0 40.0
Technical Data
Manufacturer
Frame Size
Output Power kW
Frequency Hz
Supply Voltage V
Motor Nameplate
Rated Speed rev/min
Power Factor
Rated Current A
2-pole motors Brook Hansen 200 30.0 30.0 50 50 50 60 60 60 60 60 60 50 50 50 60 60 60 60 60 60 50 50 50 60 60 60 60 60 60 50 50 50 60 60 60 60 60 60 50 50 50 60 60 60 60 60 60 220-240/380-420Y 200 380-420/660-690Y 250-280/440-480Y 200 220 440-480 400 380 220-240/380-420Y 200 380-420/660-690Y 250-280/440-480Y 200 220 440-480 400 380 220-240/380-420Y 200 380-420/660-690Y 250-280/440-480Y 200 220 440-480 400 380 220-240/380-420Y 200 380-420/660-690Y 250-280/440-480Y 200 220 440-480 400 380 220-240/380-420Y 200 380-420/660-690Y 250-280/440-480Y 200 220 440-480 400 380 Standard New Standard Standard New New Standard New New Standard New Standard Standard New New Standard New New Standard New Standard Standard New New Standard New New Standard New Standard Standard New New Standard New New Standard New Standard Standard New New Standard New New 2950 2950 2950 3540 3540 3540 3540 3540 3540 2940 2940 2940 3540 3540 3540 3540 3540 3540 2955 2955 2955 3555 3555 3555 3555 3555 3555 2960 2960 2960 3560 3560 3560 3560 3560 3560 2965 2965 2965 3565 3565 3565 3565 3565 3565 97/53 106 53/31 83/46 107 97 46 53 55 118/68 130 68/38 115/54 131 119 54 65 69 143/79 157 83/46 144/69 158 144 69 72 75 172/95 189 100/55 173/83 190 173 83 100 105 232/128 256 135/74 234/115 257 234 115 128 135
0.89
Brook Hansen
200
37.0 37.0
0.89
Brook Hansen
200
45.0 45.0
0.90
Brook Hansen
250
55.0 55.0
0.90
Brook Hansen
250
75.0 75.0
0.90
Table 14.11a Changing motor name plates
Technical Data
Glossary of Terms
15. Glossary of Terms

This section explains the various terms found in this handbook.
Absolute Pressure
Total pressure exerted by a fluid i.e. atmospheric pressure plus gauge pressure. Measure of how resistive the flow of a fluid is between two layers of fluid in motion. Connection piece between the motor and back plate on a centrifugal and liquid ring pump. Fluid viscosity increases with time under shear conditions. Part of a centrifugal and liquid ring pump, which together with the pump casing forms the fluid chamber. Vacuous space in the inlet port of a pump normally occupied by fluid. Tending to move out from the centre. Cleaning In Place - ability to clean pump system without dismantling pump and system. Pump speed required to overcome slip for a rotary lobe pump. Fluids mass per unit of volume. Total absolute pressure differences across the pump during operation i.e. discharge pressure minus suction pressure. Fluid viscosity increases as shear rate increases. Pressure at which fluid is leaving the pump.
Absolute Viscosity
Adaptor
Anti-thixotropic Back Plate
Cavitation Centrifugal CIP
Dead Head Speed Density Differential Pressure
Dilatant Discharge Pressure
Glossary of Terms
Duty Point Dynamic Head
Intersection point between the pump curve and the process curve. Energy required to set fluid in motion and to overcome any resistance to that motion. Non-metallic sealing device that exhibits elastic strain characteristics. Method of surface finishing achieved by an electro-chemical process. Positive inlet pressure/head. Pressure drop on both inlet and discharge sides of the pump due to frictional losses in fluid flow. Pressure within a gauge that exceeds the surrounding atmospheric pressure, using atmospheric pressure as a zero reference. Theoretical energy required to pump a given quantity of fluid against a given total head. Pumping element of a centrifugal and liquid ring pump. Pressure at which fluid is entering the pump. Measure of how resistive the flow of a fluid is under the influence of gravity. Flow characteristic whereby the fluid moves through the pipe in concentric layers with its maximum velocity in the centre of the pipe, decreasing to zero at the pipe wall. A pump with more than one impeller mounted on the same shaft and connected so as to act in series. Fluid viscosity is constant with change in shear rate or agitation. Net Positive Suction Head describing the inlet condition of a pump and system. Net Positive Suction Head available in a system. Net Positive Suction Head required from a pump. Net Inlet Pressure Available in a system. Net Inlet Pressure Required from a pump.
Elastomer Electropolishing Flooded Suction Friction Head
Gauge Pressure
Hydraulic Power
Impeller Inlet Pressure Kinematic Viscosity
Laminar Flow
Multi-stage
Newtonian NPSH
NPSHa NPSHr NIPA NIPR
Glossary of Terms
Non-Product Wetted
Metallic and elastomeric components not in contact with the fluid being pumped. Pressure at which fluid is leaving the pump. Pump type whereby the fluid pumped is directly displaced. Result of frictional losses in pipework, fittings and other process equipment. Result of change in fluid velocity. Metallic and elastomeric components in contact with the fluid being pumped. Fluid viscosity decreases as shear rate increases. Part of a centrifugal and liquid ring pump, which together with the back plate forms the fluid chamber. Power needed at the pump shaft. Ratio of inertia forces to viscous forces giving a value to determine type of flow characteristic. Science of fluid flow. Fluid viscosity decreases with time under shear conditions but does not recover. A machine to transfer rotating mechanical energy into kinetic energy in the form of fluid velocity and pressure. Pumping element of a rotary lobe pump. Part of a rotary lobe pump, which together with the rotorcase cover forms the pump chamber. Part of a rotary lobe pump, which together with the rotorcase forms the pump chamber. Method of surface finishing achieved by vibrating components with abrasive particulate. Method of surface finishing achieved by blasting finished components with small metallic particles at great force.
Outlet Pressure Positive Displacement Pressure Drop
Pressure Shock Product Wetted
Pseudoplastic Pump Casing
Required Power Reynolds Number (Re)
Rheology Rheomalactic
Rotodynamic
Rotor Rotorcase
Rotorcase Cover
Rumbling
Shotblasting
Glossary of Terms
SIP
Steam or Sterilisation In Place - ability to steam clean or sterilise pump system without dismantling pump and system. Fluid lost by leakage through the pump clearances of a rotary lobe pump. Ratio of a fluids density to the density of water. Fluids weight per unit volume. Difference in fluid levels. Difference in height between the fluid level and the centre line of the pump inlet on the discharge side of the pump. Difference in height between the fluid level and the centre line of the pump inlet on the inlet side of the pump. Fluid level is below the centre line of the pump inlet. Pressure at which fluid is entering the pump. Rapid temperature change of pumphead components. Fluid viscosity decreases with time under shear conditions. Moment of force required to produce rotation. Sum of the static discharge and dynamic heads. Relationship between the input power at the pump shaft and output power in the form of water horsepower. Total pressure difference between the total discharge head and the total suction head of the pump. Difference in height between the static discharge head and the static suction head. Static suction head less the dynamic head. Flow characteristic combining both laminar and turbulent flow tendencies. Flow characteristic whereby considerable mixing of the fluid takes place across a pipe section with velocity remaining fairly constant.
Slip
Specific Gravity Specific Weight Static Head Static Discharge Head
Static Suction Head
Suction Lift Suction Pressure Thermal Shock Thixotropic Torque Total Discharge Head Total Efficiency
Total Head
Total Static Head
Total Suction Head Transitional Flow
Turbulent Flow
Glossary of Terms
Vacuum Vapour Pressure
Pressure in a pumping system below normal atmospheric pressure. Pressure at which a fluid will change to a vapour, at a given temperature. Distance a fluid moves per unit of time. Measure of how resistive a fluid is to flow. Power loss due to viscous fluid friction within the pump. Ratio of actual capacity against theoretical capacity.
Velocity Viscosity Viscous Power Volumetric Efficiency
Glossary of Terms
Alfa Laval in brief Alfa Laval is a leading global provider of specialized products and engineering solutions. Our equipment, systems and services are dedicated to assisting customers in optimizing the performance of their processes. Time and time again. We help them heat, cool, separate and transport products such as oil, water, chemicals, beverages, foodstuff, starch and pharmaceuticals. Our worldwide organization works closely with customers in almost 100 countries to help them stay ahead.
How to contact Alfa Laval Contact details for all countries are continually updated on our website. Please visit www.alfalaval.com to access the information.
PM66050GB2 2002

Alfa Laval Pump Handbook PDF

Uploaded by

Copyright:

Available Formats

Alfa Laval Pump Handbook PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Alfa Laval Pump Handbook PDF

Uploaded by

Copyright:

Available Formats

All you need to know ...

Alfa Laval Pump Handbook

Second edition 2002

1 Introduction 2 Terminology and Theory 3 Pump Selection 4 Pump Description

Alfa Laval Pump Handbook 1

Section 5: Pump Materials of Construction

Section 2: Terminology and Theory

Section 6: Pump Sealing

Section 7: Pump Sizing

Section 3: Pump Selection

Section 4: Pump Description

Alfa Laval Pump Handbook 2

Section 8: Pump Specifications Options

12.2 12.2.1 12.2.2 12.3 12.4 12.5 12.5.1

201 201 202 203 204 204 204

Section 13: Troubleshooting

Section 14: Technical Data

Section 10: Cleaning Guidelines

Section 11: Compliance with International Standards and Guidelines

Section 12: Installation Guide

Section 15: Glossary of Terms

Alfa Laval Pump Handbook 3

...if pumps are the question

1.1 What is a Pump?

Fig. 1.1a Typical pump installation

Screw Circumferential Piston Gear Internal External

Piston Archimedian Screw Flexible Member Peristaltic Vane

Rotary Lobe Alfa Laval Rotary Lobe

Fig. 1.1b Pump classifications

6 Alfa Laval Pump Handbook

Terminology and Theory

2. Terminology and Theory

Alfa Laval Pump Handbook 7

Terminology and Theory

2.1 Product/Fluid Data

8 Alfa Laval Pump Handbook

Terminology and Theory

where is the fluid density (see 2.1.3).

Fig. 2.1.2a Viscosity variation with temperature

Fig. 2.1.2b Newtonian Fluids

Alfa Laval Pump Handbook 9

Terminology and Theory

Normal Viscometer Reading

Typical Shear Rate in Pumping System

Fig. 2.1.2c Viscosity against shear rate

Fig. 2.1.2d Viscosity against shear rate

Fig. 2.1.2e Pseudoplastic Fluids

Dilatant Fluids Viscosity increases as shear rate increases.

Typical fluids are: Clay Slurries Paper Coatings

Fig. 2.1.2f Dilatant Fluids

10 Alfa Laval Pump Handbook

Terminology and Theory

Fig. 2.1.2g Thixotropic Fluids

Fig. 2.1.2h Anti-thixotropic Fluids

Typical fluids are: Natural Rubber Latex Natural Yoghurt

Fig. 2.1.2i Rheomalactic Fluids

Y Where Y = Yield Stress

Typical fluids are: Barium X-ray Meal Chocolate Tomato Ketchup

Fig. 2.1.2j Plastic Fluids