4d88e Yanmmar

SHOP MANUAL
WEBMTNV000
3D82AE SERIES 3D84E SERIES 3D88E SERIES 4D88E SERIES 4D98E SERIES 4D106 SERIES S4D84E SERIES S4D98E SERIES S4D106 SERIES
DIESEL ENGINE
SHOP MANUAL
APPLICABLE MACHINE MODEL PC27R-8 PC35R-8 PC45R-8 PC75R-2 PW75R-2 PC95R-2 PW95R-2 PC110R-1 PW110R-1 SK510-5 SK714-5 SK815-5 SK815-5 turbo SK818-5 SK820-5 turbo SK1020-5 SK1020-5 turbo SK1026-5 turbo WB70A-1 WB98A-2 WB91R-2 WB93R-2 WB97R-2 WB97S-2 WB150AWS-2 ENGINE MODEL
YANMAR DESCRIPTION
WEBMTNV000
KOMATSU DESCRIPTION
3TNV82A-M5FA 3TNV88-N5FA 4TNV88-N5FA 4TNV98-X2FB 4TNV98-X2FB 4TNV106-S2FB 4TNV106-S2FB 4TNV106T-W2FB 4TNV106T-W2FB 3TNV84-K5FD 4TNV88-K5FD 4TNV88-K5FD 4TNV84T-K5FD 4TNV88-K5FD 4TNV84T-K5FD 4TNV98-N2FE 4TNV98T-N2FE 4TNV98T-N2FE 4TNV98-N2FA 4TNV106T-S2FC 4TNV106-S2FA 4TNV106T-S2FA 4TNV106T-S2FA 4TNV106T-S2FA 4TNV106T-S2FA
3D82AE-5MFA 3D88E-5NFA 4D88E-5NFA 4D98E-2XFB 4D98E-2XFB 4D106-2SFB 4D1062SFB S4D106-2WFB S4D106-2WFB 3D84E-5KFD 4D88E-5KFD 4D88E-5KFD S4D84E-5KFD 4D88E-5KFD S4D84E-5KFD 4D98E-2NFE S4D98E-2NFE S4D98E-2NFE 4D98E-2NFA S4D106-2SFC 4D106-2SFA S4D106-2SFA S4D106-2SFA S4D106-2SFA S4D106-2SFA
PREFACE
This manual describes the service procedures for the TNV series engines of indirect injection system that have been certified by the US EPA, California ARB and/or the 97/68/EC Directive for industrial use.
Please use this manual for accurate, quick and safe servicing of the said engine. Since the explanation in this manual assumes the standard type engine, the specifications and components may partially be different from the engine installed on individual work equipment (power generator, pump, compressor, etc.). Please also refer to the service manual for each work equipment for details. The specifications and components may be subject to change for improvement of the engine quality without notice. If any modification of the contents described herein becomes necessary, it will be notified in the form of correction information each time.
SAFETY LABELS
Most accidents are caused by negligence of basic safety rules and precautions. For accident prevention, it is important to avoid such causes before development to accidents.
Please read this manual carefully before starting repair or maintenance to fully understand safety precautions and appropriate inspection and maintenance procedures.
Attempting at a repair or maintenance job without sufficient knowledge may cause an unexpected accident. It is impossible to cover every possible danger in repair or maintenance in the manual. Sufficient . Especially for consideration for safety is required in addition to the matters marked safety precautions in a repair or maintenance job not described in this manual, receive instructions from a knowledgeable leader. Safety marks used in this manual and their meanings are as follows:
DANGER-indicates an imminently hazardous situation, which,

if not avoided, WILL result in death or serious injury.
WARNING-indicates a potentially hazardous situation, which, if not avoided, COULD result in death or serious injury. CAUTION-indicates a potentially hazardous situation, which, if not
avoided, MAY result in minor or moderate injury.
NOTICE-indicates that if not observed, the product performance or quality may not be
guaranteed.
Safety Precautions
(1) SERVICE AREA Sufficient Ventilation Inhalation of exhaust fumes and dust particles may be hazardous to ones health. Running engines welding, sanding, painting, and polishing tasks should be only done in well ventilated areas.
Safe / Adequate Work Area

The service area should be clean, spacious, level and free from holes in the floor, to prevent slip or trip and fall type accidents.
Bright, Safely Illuminated Area

The work area should be well lit or illuminated in a safe manner. For work in enclosed or dark areas, a drop cord should be utilized. The drop cord must have a wire cage to prevent bulb breakage and possible ignition of flammable substances.
Safety Equipment
Fire extinguisher(s), first aid kit and eye wash / shower station should be close at hand (or easily accessible) in case of an emergency.
(2) WORK WEAR (GARMENTS Safe Work Clothing

Appropriate safety wear (gloves, special shoes/boots, eye/ear protection, head gear, harness, clothing, etc.) should be used/worn to match the task at hand. Avoid wearing jewelry, unbuttoned cuffs, ties or loose fitting clothes around moving machinery. A serious accident may occur if caught in moving/rotating machinery.
(3) TOOLS Appropriate Lifting / Holding

When lifting an engine, use only a lifting device (crane, jack, etc.) with sufficient lifting capacity. Do not overload the device. Use only a chain, cable, or lifting strap as an attaching device. Do not use rope, serious injury may result. To hold or support an engine, secure the engine to a support stand, test bed or test cart designed to carry the weight of the engine. Do not overload this device, serious injury may result. Never run an engine without being properly secured to an engine support stand, test bed or test cart, serious injury may result.
Appropriate Tools
Always use tools that are designed for the task at hand. Incorrect usage of tools may result in damage to the engine and or serious personal injury.
(4) GENUINE PARTS and MATERIALS Genuine Parts

Always use genuine parts or recommended parts and goods. Damage to the engine, shortened engine life and or personal injury may result.
(5) FASTENER TORQUE Torqueing Fasteners

Always follow the torque values and procedures as designated in the service manual. Incorrect values, procedures and or tools may cause damage to the engine and or personal injury.
(6) Electrical Short Circuits

Always disconnect the (-) Negative battery cable before working on the electrical system. An accidental short circuit may cause damage, fire and or personal injury. Remember to connect the (-) Negative battery cable (back onto the battery) last. Fasten the terminals tightly.
Charging Batteries
Charging wet celled batteries produces hydrogen gas. Hydrogen gas is extremely explosive. Keep sparks, open flame and any other form of ignition away. Explosion may occur causing severe personal injury.
Battery Electrolyte
Batteries contain sulfuric acid. Do NOT allow it to come in contact with clothing, skin and or eyes, severe burns will result.
(7) WASTE MANAGEMENT

Observe the following instructions with regard to hazardous waste disposal. Negligence of these will have a serious impact on environmental pollution concerns. 1) Waste fluids such as lube oil, fuel and coolant shall be carefully put into separate sealed containers and disposed of properly. 2) Do NOT dispose of waste materials irresponsibly by dumping them into the sewer, overland or into natural waterways. 3) Waste materials such as oil, fuel, coolant, solvents, filter elements and batteries, must be disposed of properly according to local ordinances. Consult the local authorities or reclamation facility.
(8) FURTHER PRECAUTIONS Fueling / Refueling

Keep sparks, open flames or any other form of ignition (match, cigarette, etc.) away when fueling/refueling the unit. Fire and or an explosion may result.
Hot Surfaces.
Do NOT touch the engine (or any of its components) during running or shortly after shutting it down. Scalding / serious burns may result. Allow the engine to cool down before attempting to approach the unit.
Rotating Parts
Be careful around moving/rotating parts. Loose clothing, jewelry, ties or tools may become entangled causing damage to the engine and or severe personal injury.
Preventing burns from scalding

1) Never open the radiator filler cap shortly after shutting the engine down. Steam and hot water will spurt out and seriously burn you. Allow the engine to cool down before attempt to open the filler cap. 2) Securely tighten the filler cap after checking the radiator. Steam can spurt out during engine running, if tightening loose.
Precautions for Service Work

(1) Precautions for Safety
Read the safety precautions given at the beginning of this manual carefully and always mind safety in work.
(2) Preparation for Service Work

Preparation is necessary for accurate, efficient service work. history of the engine. Preceding service date Period/operation hours after preceding service Problems and actions in preceding service Replacement parts expected to be required for service Recording form/check sheet required for service Check the customer ledger file for the
(3) Preparation before Disassembly

Prepare general tools, special service tools, measuring instruments, oil, grease, non-reusable parts, and parts expected to be required for replacement. When disassembling complicated portions, put match-marks and other marks at places not adversely affecting the function for easy reassembly.
(4) Precautions in Disassembly

Each time a parts is removed, check the part installed state, deformation, damage, roughening, surface defect, etc. Arrange the removed parts orderly with clear distinction between those to be replaced and those to be used again. Parts to be used again shall be washed and cleaned sufficiently. Select especially clean locations and use clean tools for disassembly of hydraulic units such as the fuel injection pump.
(5) Precautions for Inspection and Measurement

Inspect and measure parts to be used again as required to determine whether they are reusable or not.
(6) Precautions for Reassembly

Reassemble correct parts in correct order according to the specified standards (tightening torques, and adjustment standards). Apply oil important bolts and nuts before tightening when specified. Always use genuine parts for replacement. Always use new oil seals, O-rings, packing and cotter pins. Apply sealant to packing depending on the place where they are used. Apply of grease to sliding contact portions, and apply grease to oil seal lips.
(7) Precautions for Adjustment and Check

Use measuring instruments for adjustment to the specified service standards.
How to Read this Manual

(1) Range of Operation Explanation
This manual explains the troubleshooting, installation/removal, replacement, disassemble/reassembly, inspection, adjustment and adjusting operation procedures for the TNV series engines with direct injection system. Refer to the manufacturers manual for each of the fuel injection pump, governor, starting motor and alternator except for their installation.
(2) How to Read the Explanations

An exploded view, sectional views, a system diagram, etc. are shown at the beginning of each section as required for easy understanding of the mounted states of the components. For the removal/installation of each part, the procedure is shown with the procedural step No. in the illustration. Precautions and key points for disassembly and reassembly of parts are described as points. In the explanation for each point, detailed operation method, information, standard and precautions are described. Description Example
The job contents are described in the disassembly procedure for Nos. not shown in the illustration.
Disassembly procedure 1) Follow steps (1) to (15) of the cylinder head disassembly procedure. 2) Remove the cooling water pump. 3) Remove the crankshaft pulley. (Point 1) Operation point to be explained on a later page. Operation points Disassemble: Service point for removal Reassemble: Service point for installation Disassemble-Reassemble: Service point required in both removal and installation.
Contents omitted in this manual Though the following jobs are omitted in the explanation in this manual, they should be conducted in actual work: 3) Jacking up and lifting 4) Cleaning and washing of removed parts as required 5) Visual inspection
(3) Definition of Terms

[NOTICE]: Instruction whose negligence is very likely to cause an accident. Always observe it. Standard: Allowable range for inspection and adjustment. Limit: The maximum or minimum value that must be satisfied during inspection or adjustment.
(4) Abbreviations
Abbreviation Assy Sub-Assy a.T.D.C b.T.D.C STD IN EX Meaning assembly sub-assembly after top dead center before top dead center Standard Intake Exhaust Abbreviation T.D.C. B.D.C. OS US Min-1 PS T Meaning top dead center bottom dead center oversize undersize revolutions per minute Output (metric horsepower) Bolt/nut tightening torque
CONTENTS
1. General ....................................................................................................... 1
1.1 Engine Nomenclature .............................................................................................................. 1 1.2 Specifications........................................................................................................................... 1 1.3 Fuel Oil, Lubricating Oil and Cooling Water........................................................................... 14
1.3.1 Fuel oil....................................................................................................................................14 1.3.2 Lubricating oil .........................................................................................................................15 1.3.3 Cooling water .........................................................................................................................15
1.4 Engine External Views........................................................................................................... 16

1.5 Structural Description ............................................................................................................. 17
1.6 Exhaust gas emission regulation........................................................................................... 18

1.6.1 The Emission Standard in USA ..............................................................................................18 1.6.2 Engine identification ...............................................................................................................19 1.6.3 Guarantee Conditions for the EPA Emission Standard ...........................................................20
2. Inspection and Adjustment........................................................................ 22

2.1 Periodic Maintenance Schedule ............................................................................................ 22 2.2 Periodic Inspection and Maintenance Procedure .................................................................. 23
2.2.1 Check before Daily Operation ................................................................................................23 2.2.2 inspection after initial 50 hours operation ...............................................................................25 2.2.3 Inspection every 50 hours ......................................................................................................28 2.2.4 Inspection every 250 hours or 3 months ................................................................................32 2.2.5 Inspection every 500 hours or 6 months ................................................................................35 2.2.6 Inspection every 1,000 hours or one year ..............................................................................37 2.2.7 Inspection every 2000 hours or 2 years .................................................................................46
2.3 Adjusting the no-load maximum or minimum speed.............................................................. 49 2.4 Sensor Inspection.................................................................................................................. 50
2.4.1 Oil pressure switch .................................................................................................................50
2.4.2 Thermo switch ........................................................................................................................50
2.5 Water leak check in cooling water system............................................................................. 50 2.6 Radiator cap inspection ......................................................................................................... 51 2.7 Thermostat Inspection ........................................................................................................... 51 2.8 Adjusting Operation ............................................................................................................... 52 2.9 Long storage.......................................................................................................................... 52
3. TROUBLESHOOTING .............................................................................. 53
3.1 Preparation before troubleshooting ....................................................................................... 53 3.2 Quick Reference Table for Troubleshooting .......................................................................... 54 3.3 Troubleshooting by measuring Compression Pressure......................................................... 57
4. Disassembly, Inspection and Reassembly of Engines.............................. 59

4.1 Complete disassembly and reassembly ................................................................................ 59
4.1.1 Introduction ............................................................................................................................59 4.1.2 Special service tools...............................................................................................................60 4.1.3 Complete disassembly ...........................................................................................................65 4.1.4 Precautions before and during reassembly ............................................................................69 4.1.5 Adjusting operation.................................................................................................................69
4.2 Cylinder Head: Disassembly, Inspection and Reassembly.................................................... 70

4.2.1 Components (2-valve cylinder head)......................................................................................70 4.2.2 Disassembly procedure:.........................................................................................................70 4.2.3 Reassembly procedure: .........................................................................................................71 4.2.4 Servicing points ......................................................................................................................72 4.2.5 Parts Inspection and measurement........................................................................................76 4.2.6 Valve seat correction ..............................................................................................................80 4.2.7 Valve guide replacement ........................................................................................................81 4.2.8 Valve stem seal replacement..................................................................................................82
4.3 Gear Train and Camshaft ...................................................................................................... 83

4.3.1 Components ...........................................................................................................................83 4.3.2 Disassembly procedure:.........................................................................................................83 4.3.3 Reassembly procedure: .........................................................................................................83 4.3.4 Servicing points ......................................................................................................................84 4.3.5 Parts inspection and measurement ........................................................................................87 4.3.6 Oil seal replacement (Gear case side) ...................................................................................89 4.3.7 Camshaft bushing replacement..............................................................................................89
4.4 Cylinder Block........................................................................................................................ 90

4.4.1 Components ...........................................................................................................................90 4.4.2 Disassembly procedure:.........................................................................................................90 4.4.3 Reassembly procedure: .........................................................................................................90 4.4.4 Servicing points ......................................................................................................................91 4.4.5 Parts inspection and measurement ........................................................................................95 4.4.6 Cylinder bore correction .......................................................................................................106 4.4.7 Piston pin bushing replacement ...........................................................................................107 4.4.8 Oil seal replacement (Flywheel housing side) ......................................................................107
5. LUBRICATION SYSTEM ........................................................................ 108

5.1 Lubrication System Diagram ............................................................................................... 108 5.2 Trochoid Pump Components ............................................................................................... 109 5.3 Disassembly(Reverse the procedure below for assembly) ................................................. 109 5.4 Servicing Points................................................................................................................... 109 5.5 Parts Inspection and Measurement......................................................................................110
5.5.1 Trochoid pump inspection and measurement....................................................................... 110
6. COOLING SYSTEM.................................................................................112
6.1 Cooling Water System ..........................................................................................................112 6.2 Cooling Water Pump Components .......................................................................................112 6.3 Disassembly (Reverse the procedure below for assembly) .................................................113 6.4 Servicing Points....................................................................................................................113
7. FUEL INJECTION PUMP/GOVERNOR...................................................114

7.1 Introduction ...........................................................................................................................114
7.2 Fuel Injection Pump..............................................................................................................114

7.2.1 Fuel system diagram ............................................................................................................ 114 7.2.2 External view and components.............................................................................................115 7.2.3 Disassembly procedure:....................................................................................................... 115 7.2.4 Assembly procedure............................................................................................................. 116 7.2.5 Servicing points .................................................................................................................... 116
8. TURBOCHAGER: Disassembly, inspection and reassembly.....................118

8.1 Structure and Functions........................................................................................................118
8.1.1 Main specifications ............................................................................................................... 118 8.1.2 Construction ......................................................................................................................... 118 8.1.3 Structural and functional outline ........................................................................................... 119 8.1.4 Components .........................................................................................................................120
8.2 Service Standards and Tightening Torque ........................................................................... 121

8.2.1 Service standards.................................................................................................................121 8.2.2 Tightening torque..................................................................................................................122
8.3 Periodic Inspection Procedure............................................................................................. 123

8.3.1 Periodic inspection intervals .................................................................................................123 8.3.2 Inspection procedure............................................................................................................124 8.3.3 Waste gate valve adjustment procedure ..............................................................................125
8.4 Disassembly Procedure....................................................................................................... 127

8.4.1 Preparation for disassembly .................................................................................................127 8.4.2 Inspection before disassembly .............................................................................................128 8.4.3 Disassembly .........................................................................................................................128
8.5 Washing and Inspection procedure ..................................................................................... 130

8.5.1 Washing ...............................................................................................................................130 8.5.2 Inspection procedure............................................................................................................131
8.6 Reassembly Procedure ....................................................................................................... 134

8.6.1 Preparation for reassembly...................................................................................................134
8.6.2 Reassembly .........................................................................................................................134
8.7 Handling after Disassembly and Reassembly ..................................................................... 137

8.7.1 Instructions for turbocharger installation...............................................................................137
8.8 Troubleshooting ................................................................................................................... 138

8.8.1 Excessively exhaust smoke .................................................................................................138 8.8.2 White smoke generation.......................................................................................................138 8.8.3 Sudden oil decrease.............................................................................................................139 8.8.4 Decrease in output ...............................................................................................................139 8.8.5 Poor (slow) response (starting) of turbocharger ...................................................................139 8.8.6 Abnormal sound or vibration.................................................................................................139
9. STARTING MOTOR ................................................................................ 140

9.1 For 4TNV94L/ 98 ................................................................................................................. 140
9.1.1 Specifications .......................................................................................................................140 9.1.2 Components .........................................................................................................................141 9.1.3 Troubleshooting....................................................................................................................142 9.1.4 Names of parts and disassembly procedure ........................................................................143 9.1.5 Inspection and Maintenance ................................................................................................147 9.1.6 Service standards.................................................................................................................152 9.1.7 Assembly ..............................................................................................................................153 9.1.8 Characteristic test.................................................................................................................155
9.2 For 4TNV106(T) .................................................................................................................. 156

9.2.1 Specifications .......................................................................................................................156 9.2.2 Congiguration drawing .........................................................................................................156
9.2.3 Troubleshooting ....................................................................................................................157
9.2.4 Component names and disassembly procedure ..................................................................158 9.2.5 Disassembly procedure........................................................................................................159 9.2.6 Inspection and maintenance ................................................................................................167 9.2.7 Assembly ..............................................................................................................................173 9.2.8 Adjustment ...........................................................................................................................174 9.2.9 Service standards.................................................................................................................175
10. ALTERNATOR....................................................................................... 176

10.1 The 40A Alternator for 3TNV84 and other models............................................................. 176
10.1.1 Components .......................................................................................................................176 10.1.2 Specifications .....................................................................................................................177 10.1.3 Wiring diagram ...................................................................................................................177 10.1.4 Standard output characteristics ..........................................................................................178 10.1.5 Inspection ...........................................................................................................................178
10.2 Troubleshooting ................................................................................................................. 179
11. ELECTRIC WIRING .............................................................................. 180

11.1 Electric Wiring Diagram ..................................................................................................... 180 11.2 PRECAUTION ON ELECTRIC WIRING............................................................................ 181
11.2.1 Alternator ............................................................................................................................181 11.2.2 Starter .................................................................................................................................182 11.2.3 Current limiter .....................................................................................................................183 11.2.4 Section area and resistance of electric wire .......................................................................184
12. SERVICE STANDARDS ....................................................................... 185

12.1 Engine Tuning.................................................................................................................... 185 12.2 Engine Body ...................................................................................................................... 186
12.2.1 Cylinder head .....................................................................................................................186 12.2.2 Gear train and camshaft .....................................................................................................189 12.2.3 Cylinder block.....................................................................................................................190
12.3 Lubricating Oil System (Trochoid Pump) ........................................................................... 195

12.3.1 Outside clearance of outer rotor .........................................................................................195 12.3.2 Side clearance of outer rotor ..............................................................................................195 12.3.3 Inside clearance of inner rotor ............................................................................................195 12.3.4 Rotor shaft clearance .........................................................................................................195
13. TIGHTENING TORQUE for BOLTS and NUTS .................................... 196

13.1 Tightening Torques for Main Bolts and Nuts ...................................................................... 196 13.2 Tightening Torques for Standard Bolts and Nuts ............................................................... 197
1. General
1. General
1.1 Engine Nomenclature
The engine specification class Classification Load CL VM Constant load Variable load
Engine speed Constant speed Variable speed
Available engine speed (min-1) 1500/1800 2000-3000
The engine specification class (CL or VM) is described in the specifications table.
1.2 Specifications
NOTE: 1) The information described in the engine specifications tables (the next page and after) is for "standard" engine. To obtain the information for the engine installed in each machine unit, refer to the manual provided by the equipment manufacturer. 2) Engine rating conditions are as follows (SAE J1349, ISO 3046/1) Atmospheric condition: Room temp. 25 , Atmospheric press. 100 kPa (750mm Hg), Relative humidity 30% Fuel temp: 25 (Fuel injection pump inlet) With cooling fan, air cleaner, exhaust silencer. After running-in hours. Output allowable deviation: 3%
1. General
(1) 3TNV82A
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L Overall length Overall width Overall height mm mm mm kg mm mm 120 90 138 553 489 565 128 335 mm O/D, 6 blades pusher type 110 110 1500 1800 CL 3TNV82A VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 3 82 84 1.331 2000 2200 2400 2500 2600 2800 3000
9.9 12.0 (13.5) (16.3) 1500 1800
Rated output
11.0 13.2 14.6 16.0 17.5 18.2 19.0 20.4 21.9 (14.9) (17.9) (19.9) (21.8) (23.8) (24.8) (25.8) (27.8) (29.8) 1600 1895 2180 2375 2570 2675 2780 2995 3180
1-3-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 3.6 1.2 1.8 528 5.5 2.2
Coolant water capacity (engine only) Engine Dimensions ** (with flyw Crankshaft V pulley diameter & heel housing) Engine mass (dry) ** (with flywheel housing) Cooling fan (std.) Fun V pulley diameter (std.)
* Engine oil capacity may differ from the above depending on an engine installed on a machine unit. ** Engine mass and dimensions without radiator
1. General
(2) 3TNV84
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L Overall length Overall width Overall height mm mm mm kg mm 161 589 486 622 155 335 mm O/D, 6 blades pusher type 1500 1800 CL 3TNV84 VM
11.3 13.5 (15.3) (18.3) 1500 1800
Rated output
12.4 14.8 16.4 18.1 19.7 20.5 21.3 23.0 24.6 (16.8) (20.1) (22.3) (24.6) (26.8) (27.9) (29.0) (31.3) (33.5) 1600 1895 2180 2400 2590 2690 2810 2995 3210
1-3-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD 6.7 1.9 1.8 564
Coolant water capacity (engine only) Engine dimensions ** (with flywheel housing) Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
Crankshaft V pulley diameter & mm 120 90 110 110 Fun V pulley diameter (std.) * Engine oil capacity may differ from the above depending on an engine installed on a machine unit.
** Engine mass and dimensions without radiator
1. General
(3) 3TNV84T
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg mm 161 589 486 622 155 350 mm O/D, 6 blades pusher type 1500 1800 14.0 16.5 (19.0) (22.5) 1500 1800 15.8 18.8 (21.5) (25.5) 1600 1895 2000 CL 3TNV84T VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 3 84 90 1.496 2200 2400 2500 2600 2800 3000 25.0 25.9 26.8 29.1 30.9 (34.0) (35.2) (36.5) (39.5) (42.0) 2590 2700 2810 2995 3210 1-3-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (cetane No.45 min.) API grade class CD or CF 6.7 1.9 2.0 564
Rated output
Coolant water capacity (engine only) Overall length Engine dimensions ** Overall (with flywheel housing) width Overall height Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
Crankshaft V pulley diameter & mm 120 90 110 110 Fun V pulley diameter (std.) * Engine oil capacity may differ from the above depending on an engine installed on a machine unit. ** Engine mass and dimensions without radiator
1. General
(4) 3TNV88
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg Mm 589 486 622 155 350 mm O/D, 6 blades pusher type 1500 1800 CL 3TNV88 VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 3 88 90 1.642 2000 18.0 24.5) 2180 2200 2400 2500 2600 2800 3000 27.1 (36.8) 3210
12.3 14.8 (16.7) (20.1) 1500 1800 13.5 16.3 (18.4) (22.1) 1600 1895
Rated output
19.9 21.6 22.6 23.5 25.2 (27.0) (29.4) (30.7) (31.9) (34.2) 2400 2590 2700 2810 2995
1-3-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 4.7 1.8 2.0 564 7.2 3.5
Effectiv e Coolant water capacity (engine only) Overall length Engine dimensions ** Overall (with flywheel housing) width Overall height Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
Crankshaft V pulley diameter & Mm 120 90 120 90 Fun V pulley diameter (std.) * Engine oil capacity may differ from the above depending on an engine installed on a machine unit.
1. General
(5) 4TNV84
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous Rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg mm 183 683 498.5 617 170 370 mm O/D, 6 blades pusher type 1500 1800 CL 4TNV84 VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 4 84 90 1.995 2000 2200 2400 2500 2600 2800 30.7 41.7) 2995 3000 32.9 (44.7) 3210
14.9 17.7 (20.3) (24.1) 1500 1800 16.4 19.5 21.9 24.1 (22.3) (26.5) (29.8) (32.8) 1600 1895 2180 2400
Rated output
26.3 27.4 28.5 (35.8) (37.3) (38.7) 2590 2700 2810
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (cetane No.45 min.) API grade class CD or CF 7.4 2.3 2.7 658
Coolant water capacity (engine only) Overall length Engine dimensions ** Overall (with flywheel width housing) Overall height Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
1. General
(6) 4TNV84T
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 KW (hp) Min-1 KW (hp) min-1 L L L mm mm mm kg mm 183 683 498.5 713 170 370 mm O/D, 6 blades pusher type 1500 19.1 (26.0) 1500 21.3 (29.0) 1600 1800 24.3 (33.0) 1800 26.9 (36.5) 1895 2000 27.9 (38.0) 2180 2200 30.5 (41.5) 2400 2400 33.5 (45.5) 2590 CL 4TNV84T VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 4 84 90 1.995 2600 35.7 (48.5) 2810 2800 38.6 (52.5) 2995 3000 41.2 (56.0) 3210
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 7.4 3.4 2.7 649
Coolant water capacity (engine only) Overall length Engine Overall dimensions ** width Overall height Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
1. General
(7) 4TNV88
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L Overall ength Overall width Overall height mm mm mm kg mm 183 683 498.5 618 170 370 mm O/D, 6 blades pusher type 1500 1800 CL 4TNV88 VM
16.4 19.6 (22.3) (26.7) 1500 1800
Rated output
18.0 21.6 24.1 26.5 28.8 30.1 31.3 33.7 35.4 (24.5) (29.4) (32.7) (36.0) (39.2) (40.9) (42.5) (45.8) (48.1) 1600 1895 2180 2400 2590 2700 2810 2995 3210
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (cetane No.45 min.) API grade class CD or CF 5.8 2.3 2.7 658 8.6 4.2
Coolant water capacity (engine only) Engine dimensions ** (with wheel housing) Engine mass (dry) ** (with flywheel housing) Cooling fan (std.)
1. General
(8) 4TNV94L
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L Overall length Overall width Overall height mm mm mm kg mm 245 (equivalent to SAE#3) 1500 26.1 (35.5) 1500 29.1 (39.5) 1600 1800 31.3 (42.5) 1800 34.6 (47.0) 1895 2000 35.3 (48.0) 2180 2200 38.2 (52.0) 2400 CL 4TNV94L VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 4 94 110 3.053 2400 41.6 (56.5) 2590 2500 43.0 (58.5) 2700
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 10.2 4.5 4.2 719 498 717 235 (equivalent to SAE#4)
410 mm O/D, 6 blades pusher type
Crankshaft V pulley diameter & mm 130 130 Fun V pulley diameter (std.) * Engine oil capacity may differ from the above depending on an engine installed on a machine unit.
1. General
(9) 4TNV98
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg mm 248 (equivalent to SAE#3) 1500 30.9 (42.0) 1500 34.6 (47.0 1600 1800 36.8 (50.0) 1800 41.2 (56.0) 1895 2000 41.9 (57.0) 2180 2200 45.6 (62.0) 2400 CL 4TNV98 VM
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 10.2 4.5 4.2 719 498 717 235 (equivalent to SAE#4)
410 mm O/D, 6 blades pusher type
10
1. General
(10) 4TNV98T
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L Overall length Overall width Overall height mm mm mm kg mm 258 (equivalent to SAE#3) 1500 37.9 (51.5) 1500 41.9 (57.0) 1600 1800 45.6 (62.0) 1800 50.4 (68.5) 1895 2000 50.7 (69.0) 2180 2200 55.5 (75.5) 2400 CL 4TNV98T VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 4 88 110 3.318 2400 60.3 (82.0) 2590 2500 62.5 (85.0) 2700 2600 64.0 (87.0) 2810
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (cetane No.45 min.) API grade class CD or CF 10.2 4.5 4.2 715 575 779 245 (equivalent to SAE#4)
430 mm O/D, 8 blades suction type
11
1. General
(11) 4TNV106
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg mm 808 629 803 345 (equivalent to SAE#3) 500 mm O/D, 7 blades pusher type 9.0 6.0 776 629 803 330 (equivalent to SAE#3) 500 mm O/D, 7 blades suction type 1500 41.2 (56.0) 1500 45.6 (62.0 1600 1800 49.3 (67.0) 1800 54.4 (74.0) 1895 2000 56.6 (77.0) 2180 2200 61.4 (83.5) 2400 CL 4TNV106 VM
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 14.0 7.5
12
1. General
(12) 4TNV106T
Engine name Engine specification class Type Combustion chamber Number of cylinders Cylinder bore stroke Displacement Continuous rating Revolving speed Output Revolving speed Output Max. no-load speed ( 25) Ignition order Power take off Direction of rotation Cooling system Lubrication system Starting system Applicable fuel Applicable lubricant Lubricant capacity (oil pan) * Total Effective Unit mm mm L Min-1 kW (hp) Min-1 kW (hp) min-1 L L L mm mm mm kg mm 808 629 866 355 (equivalent to SAE#3) 500 mm O/D, 7 blades pusher type 9.0 6.0 776 628.6 866 340 (equivalent to SAE#3) 500 mm O/D, 7 blades suction type 1500 51.5 (70.0) 1500 56.8 (77.2 1600 1800 61.8 (84.0) 1800 68.0 (92.5) 1895 2000 69.9 (95.0) 2180 CL 4TNV106T VM
Vertical, in-line, 4-cycle, water-cooled diesel engine Direct injection 4 106 125 4.412 2200 72.0 (97.9) 2400
Rated output
1-3-4-2-1(No.1 cylinder on flywheel side) Flywheel Counterclockwise (viewed from flywheel) Radiator Forced lubrication with trochoid pump Electric Diesel oil-ISO 8217 DMA, BS 2869 A1 or A2 (Cetane No.45 min.) API grade class CD or CF 14.0 7.5
13
1. General
1.3 Fuel Oil, Lubricating Oil and Coolant Water

1.3.1 Fuel oil
IMPORTANT: Only use the recommended fuel to obtain the best engine performance and prevent damage of parts, also prevent air pollution.
(1) Selection of fuel oil

Use the following diesel fuels for best engine performance: BS 2869 A1 or A2 Fuels equivalent to Japanese Industrial Standard, JIS. No. K2204-2 Fuel cetane number should be 45 or greater
(2) Fuel handling

Water and dust in the fuel oil can cause operation failure. Use containers which are clean inside to store fuel oil. Store the containers away from rain water and dust. Before supplying fuel, let the fuel container rest for several hours so that water and dust in the fuel are deposited on the bottom. Pump up only the clean fuel.
(3) Fuel tank

Be sure to attach a drain cock, precipitation trap and primary strainer to the fuel tank as shown illustration right.
14
1. General
1.3.2 Lubricating oil

IMPORTANT: Use of other than the specified engine oil may cause inner parts seizure or early wear, leading to shorten the engine service life.
(1) Selection of engine lube oil

Use the following engine oil API classification CD or CF (Standards of America Petroleum Institute) 10W-30 or 15W-40 SAE viscosity (Standard of Society of Automotive Engineering) Engine oil with 10W30 or 15W40 can be used throughout the year. (Refer to the right figure.)
(2) Handling of engine oil

Carefully store and handle the oil so as to prevent dust or dirt entrance. When supplying the oil, pay attention and clean around the filler port. Do not mix different types of oil as it may adversely affect the lubricating performance. When touching engine oil by hand, the skin of the hand may become rough. Be careful not to touch oil with your hands without protective gloves. If touch, wash your hands with soap and water thoroughly.
1.3.3 Coolant water

Use clean soft water and be sure to add the Long Life Coolant Antifreeze (LLC) in order to prevent rust built up and freezing. If there is any doubt over the water guality, distilled water or pre-mixed coolant should be used. The coolants / antifreezes, which are good performance for example, are shown below. TEXACO LONG LIFE COOLANT ANTIFREEZE, both standard and pre-mixed. Product codes 7997 and 7998 HAVOLINE EXTENDED LIFE ANTIFREEZE / COOLANT Product code 7994 IMPORTANT: Be sure to add Long Life Coolant Antifreeze(LLC) to soft water. In cold season, the LLC is especially important. Without LLC, cooling performance will decrease due to scale and rust in the coolant water line. Without LLC, coolant water will freeze and expand to break the cooling line. Be sure to use the mixing ratios specified by the LLC manufacturer for your temperature range. Do not mix different types (brand) of LLC, chemical reactions may make the LLC useless and engine trouble could result. Replace the coolant water every once a year. When handling Long Life Coolant Antifreeze, wear protective rubber gloves not to touch it. If LLC gets eyes or skin, wash with clean water at once.
15
1. General
1.4 Engine External Views
16
1. General
1.5 Structural Description
17
1. General
1.6 Exhaust gas emission regulation

The engines in this manual have been certified by the US EPA, California ARB and/or the 97/68/EC Directive. California Proposition 65 Warning Diesel engine exhaust and some of its constitutions are known to the State of California to cause cancer, birth defects, and other reproductive harm. California Proposition 65 Warning Battery poststerminalsand related accessories contain lead and lead compoundschemicals known to the State of California to cause cancer and reproductive harm
1.6.1 The Emission Standard in USA

(1) EPA Nonroad Diesel Engine Emission Standards
Engine Power kW < 8 (hp < 11) 8 <= kW < 19 (11 <= hp < 25) 19<= kW < 37 (25 <= hp < 50) Tier Tier 1 Tier 2 Tier 1 Tier 2 Tier 1 Tier 2 Tier 1 37 <= kW < 75 (50 <= hp < 100) Tier 2 Tier 3 Tier 1 75 <= kW < 130 (100 <= hp < 175) Tier 2 Tier 3 Model Year 2000 2005 2000 2005 1999 2004 1998 2004 2008 1997 2003 2007 NOx 9.2 (6.9) 9.2 (6.9) HC NMHC+NOx 10.5 (7.8) 7.5 (5.6) 9.5 (7.1) 7.5 (5.6) 9.5 (7.1) 7.5 (5.6) 7.5 (5.6) 4.7 (3.5) 6.6 (4.9) 4.0 (3.0) g/kWhr(g/bhphr) CO PM 8.0 (6.0) 8.0 (6.0) 6.6 (4.9) 6.6 (4.9) 5.5 (4.1) 5.5 (4.1) 5.0 (3.7) 5.0 (3.7) 5.0 (3.7) 5.0 (3.7) 1.0 (0.75) 0.80 (0.60) 0.80 (0.60) 0.80 (0.60) 0.80 (0.60) 0.60 (0.45) 0.40 (0.30) 0.30 (0.22)
Note1) The EPA emission regulation under 130kW is mentioned below. Note2) As for Model year, the year which a regulation is applicable to is shown. Engine classification Constant speed engine Variable speed engine Transient smoke standards % opacity (acceleration/lug/peak modes) Not regulated 20/15/50 or less
(2) California ARB Emission Regulation

The ARB emission standard is based on that of the EPA.
18
1. General
1.6.2 Engine identification

(1) Emission control labels of US EPA
EPA label for constant speed engines
EPA label for variable speed engines
(2) Emission control label for both EPA and ARB
(3) 97/68EC Directive label
19
1. General
1.6.3 Guarantee Conditions for the EPA Emission Standard

The following guarantee conditions are set down in the operation manual. In addition to making sure that these conditions are met, check for any deterioration that may occur before the required periodic maintenance times.
(1) Requirement on engine installation condition

(a) Intake air depression
Initial <= 2.9(300) kPa(mmAq) Permissible <= 6.23 (635)
(b) Exhaust gas back pressure

Engine type Naturally aspirated engines 4TNV98T, 4TNV106T 3,4TNV84T Initial <= 12.7(1300) <= 9.8(1000) <= 4.9(500) kPa (mmAq) Permissible <= 15.3(1560) <= 11.7(1200) <= 5.9(600)
(2) Fuel oil and lubricating oil

(a) Fuel: The diesel fuel oil US No.2 diesel fuel oil. (b) Lube oil: API grade, class CD or CF
(3) Do not remove the seals restricting injection quantity and engine speed.
20
1. General
(4) Perform maintenance without fail.

Note: Inspections to be carried out by the user and by the maker are divided and set down in the List of Periodic Inspections and should be checked carefully.
(5) Maintenance period and Quality guarantee period for exhaust emission related parts
The maintenance of the parts related to the exhaust emission must be carried out in the maintenance period as shown in the below table. A guarantee period is that either the operation hours or years shown in the table come first in the condition that the maintenance inspection was carried out based on the List of Periodic Inspections.
Maintenance period Fuel nozzle cleaning Adjustment, cleaning, repairs for fuel nozzle, fuel pump, turbocharger, electronic control unit etc. Every 1500 hours (applied from Tier 2) Every 3000 hours (applied from Tier 2) Quality Guarantee Period For nozzle, fuel pump, turbocharger
Parts Power Rating 37 <= kW < 130
3000 hours / 5 years
19 <= kW < 37 except constant speed engines >= 3000min-1 KW < 19 And constant speed engines beyond 3000min-1 under 37kW
Every 1500 hours
Every 3000 hours
Every 1500 hours
Every 3000 hours
21
2. Inspection and Adjustment

2.1 Periodic Maintenance Schedule
The engine periodic inspection timing is hard to determine as it varies with the application, load status, qualities of the fuel and lubricating oils used and handling status. General rules are described here.
: User-maintenance : Parts replacement : Shop-inspection Maintenance period Every Every Every Every 250 500 1000 2000 Every 50 hours hours hours hours hours or 3 or 6 or one or two months months year years
Classification
Item
Daily
Whole
Visual check around engine Fuel tank level check and fuel supply Fuel tank draining Water separator (Option) draining Bleeding the fuel system Water separator cleaning Fuel filter element replacement Lube oil level check and replenishment
Fuel oil system
Lubricating oil system
Lube oil replacement Lube oil filter replacement Coolant water level check and replenishment Radiator fin cleaning
1 time
st
2 time and thereafter
nd
Cooling water system
V-belt tension check Coolant water replacement Coolant/water path flushing and maintenance Fuel pipe and coolant water pipe inspection and maintenance Inspection and adjustment of governor lever and accelerator Air cleaner cleaning and element replacement Diaphragm assy inspection Turbocharger blower cleaning* Warning lamp & instruments function check Battery electrolyte level check and battery recharging Intake/exhaust valve head clearance adjustment Intake/exhaust valve seat lapping
1 time
st
2 time and thereafter
nd
Rubber house Governor Air intake system
(2 years)
Electrical system Cylinder head Fuel injection pump and nozzle
Fuel injection nozzle pressure inspection * Fuel injection timing adjustment * Fuel injection pump inspection and adjustment *) EPA allows to maintain the emission related parts every 1,500 or 3,000 hours as shown in 1.6.3 of chapter1.
22
2.2 Periodic Inspection and Maintenance Procedure

2.2.1 Check before Daily Operation
Be sure to check the following points before starting an engine every day.
No. (1) (2) (3) (4) (5) (6) (7) Inspection Item Visual check around engine Fuel tank level check and fuel supply Lube oil level check and replenishment Coolant water level check and replenishment Fuel pipe and coolant water pipe inspection and maintenance Inspection and adjustment of governor lever and accelerator Warning lamp & instruments function check
(1) Visual check around engine

If any problem is found, do not use before the engine repairs have been completed. Oil leak from the lubrication system Fuel leak from the fuel system Coolant water leak from the cooling water system Damaged parts Loosened or lost bolts Fuel, radiator rubber hoses, V belt cracked, loosened clamp
(2) Fuel tank level check and fuel supply

Check the remaining fuel oil level in the fuel tank and refuel the recommended fuel if necessary. (Refer to 1.3.(1) )
(3) Lube oil level check and replenishment

(a) Checking oil level Check the lube oil level with the dipstick, after adjusting the posture of the machine unit so that an engine may become a horizontality. Insert the dipstick fully and check the oil level. The oil shall not be contaminated heavily and have appropriate viscosity. No coolant water or diesel fuel shall be mixed. When lube oil is supplied after the engine running, check the lube oil level after about 10 minutes pass after the engine shutdown so that the lube oil inside may be retuned the oil pan.
Standard The level shall be between the upper and lower limit lines on the dipstick.
23
Model 3TNV82A 3TNV84(T) 88 4TNV84(T) 88 4TNV94L 98(T) 4TNV106(T) (CL class) 4TNV106(T) (VM class)
Total volume 5.5 6.7 7.4 10.5 14.0 14.0
(L)
(Unit: liter) Effective volume (L) 1.9 2.8 3.4 4.5 9.0 7.5
Lube oil capacity may differ from the above volume depending on an engine installed on a machine unit.
(b) Replenishing oil pan with lube oil If the remaining engine oil level is low, fill the oil pan with the specified engine oil to the specified level through the filler port.
[NOTICE] The oil should not be overfilled to exceed the upper limit line. Otherwise a naturally-aspirated engine may intake lube oil in the combustion chamber during the operation, then white smoke, oil hummer or urgent rotation may occur, because the blowby gas is reduced in the suction air flow. In case of turbo-charged engine oil may jet out from the breather or the engine may become faulty.
(4) Coolant water Inspection

Daily inspection of coolant water should be done only by Coolant recovery tank. Never open the radiator filler cap while the engine and radiator are still hot. Steam and hot water will spurt out and seriously burn you. Wait until the radiator is cooled down after the engine has stopped, wrap the filler cap with a rag piece and turn the cap slowly to gently release the pressure inside the radiator. Securely tighten the filler cap after checking the radiator. Steam can spurt out during operation, if the cap is tightened loosely.
(a) Checking coolant water volume Check the coolant water level in the Coolant recovery tank. If the water level is close to the LOW mark, open the Coolant recovery tank cap and replenish the Coolant recovery tank with clean soft water to the FULL mark. Standard The water level of the Coolant recovery tank shall be between the upper and lower limit lines. (b) Replenishing engine with water If the Coolant recovery tank water level is lower than the LOW mark, open the radiator cap and check the coolant water level in the radiator. Replenish the radiator with the coolant water, if the level is low. Check the coolant water level while the engine is cool. Checking when the engine is hot is dangerous. And the water volume is expanded due to the heat. Daily coolant water level check and replenishing shall be done only at the Coolant recovery tank. Usually do not open the radiator cap to check or replenish.
24
IMPORTANT: If the coolant water runs short quickly or when the radiator runs short of water with the Coolant recovery tank level unchanged, water may be leaking or the air tightness may be lost. Increase in the Coolant recovery tank water level during operation is not abnormal. The increased water in the Coolant recovery tank returns to the radiator when the engine is cooled down. If the water level is normal in the Coolant recovery tank but low in the radiator, check loosened clamping of the rubber hose between the radiator and Coolant recovery tank or tear in the hose. Standard Engine: The radiator shall be filled up.
Model 3TNV82A 3TNV84(T) 3TNV88 4TNV84(T) 4TNV88 4TNV94L 4TNV98(T) 4TNV106(T) (Unit: liter) Coolant water volume In an engine 1.8 2.0 2.7 4.2 6.0
Engine coolant water capacity may differ from the above volume depending on an engine installed on a machine unit.
(5) Fuel pipe and coolant water pipe inspection and maintenance
Check the rubber hoses for fuel and coolant water pipes cracked. If the cracked hose is found, replace it with new one. Check the loosened clamp. If found, tighten it.
(6) Inspection and adjustment of governor lever and accelerator

Make sure the accelerator of the machine unit can be operated smoothly before starting the engine. If it feels heavy to manipulate, lubricate the accelerator cable joints and pivots. Adjust the accelerator cable if there is a dislocation or excessive play between the accelerator and the governor lever. Refer to 3.2.3.
(7) Warning lamp & instruments function check

Before and after starting the engine, check to see that the alarm function normally. Failure of alarm cannot warn the lack of the engine oil or the coolant water. Make it a rule to check the alarm operation before and after starting engine every day. Refer to each manual for machine units in details.
2.2.2 inspection after initial 50 hours operation

Be sure to check the following points after initial 50 hours operation, thereafter every 250 hours or 3 months operation.
No. (1) (2) Inspection Item Lube oil and filter replacement V-belt tension check
(1) Lube oil and filter replacement (1st time)

When an engine is still hot, be careful with a splash of engine oil which may cause burns. Replace engine oil after the engine oil becomes warm. It is most effective to drain the engine oil while the engine is still warm.
25
In early period of use, the engine oil gets dirty rapidly because of the initial wear of internal parts. Replace the engine oil earlier. Lube oil filter should also be replaced when the engine oil is replaced. The procedure of lube oil and lube oil filter replacement is as follows. (a) Drain engine oil Prepare a waste oil container collecting waste oil. Remove the oil filler cap to drain easily while draining the lube oil. Loosen the drain plug using a wrench (customer procured) to drain the lube oil. Securely tighten the drain plug after draining the lube oil. [NOTICE] Use a socket wrench or a closed wrench when removing or tightening a drain plug. Dont use a spanner because it has the possibility that the spanner will slip and it will get hurt.
(b) Replacing oil filter Turn the lube oil filter counter-clockwise using a filter wrench (customer procured) to remove it. Clean the mounting face of the oil filter. Moisten the new oil filter gasket with the engine oil and install the new engine oil filter manually turning it clockwise until it comes into contact with the mounting surface, and tighten it further to 3/4 of a turn with the filter wrench.
Tightening torque: 20 24N m (2.0 2.4kgf m)
Model 3TNV82A 4TNV98(T) 4TNV106(T) Applicable oil filter Part No. 129150-35151 119005-35100
(c) Filling oil and inspection Fill with new engine oil until it reaches the specified level.
IMPORTANT: Do not overfill the oil pan with engine oil. Be sure to keep the specified level between upper and lower limit on the dipstick. Warm up the engine by running for 5 minutes while checking any oil leakage Stop the engine after warming up and leave it stopping for about 10 minute to recheck the engine oil level with dipstick and replenish the engine oil. If any oil is spilled, wipe it away with a clean cloth.
26
(2) V-belt tension check

When there is not enough tension in the V-belt, the V-belt will slip making it impossible for the alternator to generate power and cooling water pump and cooling fan will not work causing the engine to overheat. Check and adjust the V-belt tension (deflection) in the following manner. [NOTICE] Be especially careful not to splash engine oil on the V-belt, because it will cause slipping, stretching and aging of the belt. 1) Press the V-belt with your thumb [approx. 98N(10kgf)] at the middle of the V-belt span to check the tension (deflection). Available positions to check and adjust the V-belt tension (deflection) are at the A, B or C direction as shown in the illustration right. You may choose a position whichever you can easily carry out the check and adjustment on the machine unit. "New V-belt" refers to a V-belt, which has been used less than 5 minutes on a running engine. "Used V-belt" refers to a V-belt, which has been used on a running engine for 5 minutes or more. The specified deflection to be measured at each position should be as follows.
Direction For used V-belt For new V-belt A 10 14 8 12 B 7 10 5 8 (Unit: mm) C 9 13 7 11
2) If necessary, adjust the V-belt tension (deflection). To adjust the V-belt tension, loosen the set bolt and move the alternator to tighten the V-belt. After replacing with a new V-belt and adjusting it, run the engine for 5 minutes and readjust the deflection to the value in the table above. 3) After replacing with a new V-belt and adjusting it, run the engine for 5 minutes and readjust the deflection to the value in the table above. 4) Visually check the V-belt for cracks, oiliness or wear. If any, replace the V-belt with new one.
27
2.2.3 Inspection every 50 hours

Be sure to check the following points every 50 hours operation.
No. (1) (2) (3) (4) Fuel tank draining Water separator draining Bleeding the fuel system Battery electrolyte level check and battery recharging Inspection Item
(1) Fuel tank draining

1) Prepare a waste oil container. 2) Remove the drain plug of the fuel tank to drain (water, dust, etc.) from the fuel tank bottom. 3) Drain until fuel with no water and dust flow out. Then tighten the drain plug firmly.
(2) Water separator draining

Drain off the water separator whenever there is a lot of drain collected in the water separator at the bottom of the cup even if not the time for periodic inspection hour. The cup of the water separator is made from semi-transparency material and in the cup, the red colored float ring which rises on the surface of the drain is installed to visualize the amoun of drain. Also, the water separator with sensor to detect the drain for warning device on a controle panel is provided as the optional. Drain off the water separator in the following manner. 1) Prepare a waste oil container. 2) Close the fuel cock. 3) Loosen the drain cock at the bottom of the water separator, and drain off any water collected inside. 4) Tighten the drain cock with hand. 5) Be sure to bleed air in the fuel system. NOTE: If no drain drips when the drain cock is opened, loosen the air bleeding bolt on the top of the water separator by turning counter-clockwise 2 3 times using screw driver. (This may occure in case of the water separator position is higher than the fuel oil level in the fuel tank). After draining, be sure to tighten the air bleeding bolt.
28
(3) Bleeding the fuel system

Bleed the fuel system according to the following procedures. When there is air in the fuel system, the fuel injection pump will not be able to function. 1) Check the fuel oil level in the fuel tank. Refuel if insufficient. 2) Open the cock of the water separator. 3) Loosen the air bleeding bolt on the water separator by turning 2~3 times to the counter-clockwise using screw driver or spanner. 4) When the fuel coming out is clear and not mixed with any bubble, tighten the air bleeding bolt. 5) Feed the fuel with the fuel priming pump or electro-magnetic fuel feed pump. In case of the engine using the electro-magnetic fuel feed pump. Turn the starter switch to the ON position and hold it in the position for 10~15 seconds to operate the fuel feed pump. In case of the engine installed the fuel filter mounting with the fuel priming pump. The priming pump is on the top of the fuel filter mounting. Move the priming pump up and down to feed fuel until feel your hand slightly heavy.
(4) Battery electrolyte level check and battery recharging
Fire due to electric short-circuit

Make sure to turn off the battery switch or disconnect the negative cable (-) before inspecting the electrical system. Failure to do so could cause short-circuiting and fires. Always disconnect the (-) Negative battery cable first before disconnecting the battery cables from battery. An accidental "Short circuit" may cause damage, fire and or personal injury. And remember to connect the (-) Negative battery cable (back onto the battery) LAST.
Proper ventilation of the battery area

Keep the area around the battery well ventilated, paying attention to keep away any fire source. During operation or charging, hydrogen gas is generated from the battery and can be easily ignited.
Do not come in contact with battery electrolyte

Pay sufficient attention to avoid your eyes or skin from being in contact with the fluid. The battery electrolyte is dilute sulfuric acid and causes burns. Wash it off immediately with a large amount of fresh water if you get any on you.
29
Battery structure
(1) Electrolyte level

Check the level of fluid in the battery. When the amount of fluid nears the lower limit, fill with battery fluid (available in the market) to the upper limit. If operation continues with insufficient battery fluid, the battery life is shortened, and the battery may overheat and explode. Battery fluid tends to evaporate more quickly in the summer, and the fluid level should be checked earlier than the specified times. If the engine cranking speed is so slow that the engine does not start up, recharge the battery. If the engine still will not start after charging, replace the battery. Remove the battery from the battery mounting of the machine unit after daily use if letting the machine unit leave in the place that the ambient temperature could drop at -15 or less. And store the battery in a warm place until the next use the unit to start the engine easily at low ambient temperature.
(2) Battery charge

Use a battery tester or hydrometer and check the battery condition. If the battery is discharged, recharge it. (a) Measurement with a battery tester When checking the battery with the batter tester, connect the red clip of the tester to the battery positive (+) terminal and black clip to the battery negative (-) terminal by pinching them securely, and judge the battery charge level from the indicator position. Green zone: Normal Yellow zone: Slightly discharged Red zone: Defective or much discharged
30
When using a hydrometer, the measured specific gravity must be corrected according to the temperature at the time of measurement. The specific gravity of battery electrolyte is defined with 20 as the standard. Since the specific gravity increases or decreases by 0.0007 when the temperature varies by 1 , correct the value according to the equation below.
(b) Measurement with hydrometer
(c) Specific gravity and remaining battery charge

Specific gravity (20 ) 1.28 1.26 1.24 1.23 Discharged quantity of electricity (%) 0 10 20 25 Remaining charge (%) 100 90 80 75
(3) Terminals
Clean if corroded or soiled.
(4) Mounting bracket

Repair or replace it if corroded. Retighten if loosened.
(5) Battery appearance

Replace the battery if cracked or deformed. Clean with fresh water if contaminated.
31
2.2.4 Inspection every 250 hours or 3 months

Be sure to check the following points every 250 hours or 3 months operation, whichever comes first.
No. (1) (2) (3) (4) (5) Inspection Item Lube oil and filter replacement Radiator fin cleaning V-belt tension check Inspection and adjustment of governor lever and accelerator Air cleaner cleaning and element replacement
(1) Lube oil and filter replacement (The second replacement and after)
Replace the engine oil every 250 hours operation from 2nd time and on. at the same time. Refer to 2.2.1.(1). Replace the engine oil filter
(2) Radiator fin cleaning
Beware of dirt from air blowing

Wear protective equipment such as goggles to protect your eyes when blowing compressed air. Dust or flying debris can hurt eyes.
Dirt and dust adhering on the radiator fins reduce the cooling performance, causing overheating. Make it a rule to check the radiator fins daily and clean as needed. Blow off dirt and dust from fins and periphery with compressed air [0.19MPa (2kgf/cm2) or less] not to damage the fins with compressed air. If contaminated heavily, apply detergent, thoroughly clean and rinse with tap water shower. IMPORTANT: Never use high pressure water or air from close by fins or never attempt to clean using a wire brush. Radiator fins can be damaged.
(3) V-belt tension check (The second time and after)

Check and adjust the V-belt tension. Refer to 2.2.2(2)
32
(4) Inspection and adjustment of governor lever and accelerator

The governor lever and accelerating devices (accelerating lever, pedal, etc.) of the machine unit are connected by an accelerating wire or rod. If the wire becomes stretched or the connections loose, the deviation in the position may result and make operation unsafe. Check the wire periodically and adjust if necessary. Do not strongly move the accelerating wire or accelerating pedal. It may deform the governor lever or stretch the wire to cause irregular engine speed control. Checking and adjusting procedure are as follows. 1) Check that the governor lever of the engine makes uniform contact with the high idling and low idling limiting bolt when the accelerating devices is in the high idling speed or low idling speed position. 2) If either the high or the low idling speed side does not make contact with the limiting bolt, adjust the accelerating wire. Loosen the accelerating wire fixing nut and adjust the wire to contact with the limitng bolt.
Never release the limiting bolts. It will impair the safety and performance of the product and functions and result in shorter engine life.
(5) Air cleaner cleaning and element replacement
Beware of dirt from air blowing

Wear protective equipment such as goggles to protect your eyes when blowing compressed air. Dust or flying debris can hurt eyes.
The engine performance is adversely affected when the air cleaner element is clogged by dust. So periodical cleaning after disassembly is needed. 1) Undo the clamps on the dust pan and remove the dust pan. 2) Loosen the wing bolt on the element and pull out the element.
33
3) Blow air [0.29 0.49MPa (3.0 5.0kgf/cm2)] from inside the element to blow dust off as shown in the illustration right. Apply the air blowing pressure as low as possible so as not to damage the element. If having the air cleaner with double elements, never remove and clean the inner element. The aim of installing the inner element is for back up protecting from intaking dust during engine running when leaving the outer element to reinstall after removing it or when damaging the outer element unexpectedly during engine running. 4) Replace the element with new one, If the element is damaged, excessively dirty or oily. 5) Remove the inside dust cover of the dust pan, and clean inside of the dust pan. 6) Reinstall the element with the wing bolt. (do not leave the gasket.) Reattach the inside dust cover to the dust pan and install the dust pan to the air cleaner case placing the TOP mark upward. IMPORTANT: When the engine is operated in dusty conditions, clean the element more frequently. Do not run the engine with removed air cleaner or element, as this may cause foreigh material to enter and damage the engine.
34
2.2.5 Inspection every 500 hours or 6 months

Be sure to check the following points every 500 hours or 6 months operation, whichever comes first.
No. (1) (2) (3) Inspection Item Water separator cleaning Fuel filter element replacement Air cleaner cleaning and element replacement
(1) Water separator cleaning

Periodically wash the water separator element and inside cup with clean fuel oil. 1) Prepare a waste oil container. 2) Close the fuel cock. 3) Loosen the drain cock and drain. Refer to 2.2.3.(2) 4) Turn the retaining ring counter-clockwise and remove the cup. (Disconnect the coupler of the lead wire for drain sensor before removing the cup if it is with drain sensor). 5) Wash the element and inside cup with clean fuel oil. Replace the element with new one if any damaged.
Model 3TNV82A 4TNV106(T) Applicable element Part No. 119802-55710
6) Insert the element to the bracket (O-ring) and after putting the float ring in the cup, install it to the bracket by tightening the retaining ring clockwise. Tightening torque: 15 20Nm (1.5 2.0kgf-m) 7) Close the drain cock (connect the coupler if with drain sensor). 8) Bleed the fuel system. Refer to 2.2.3.(3)
35
(2) Fuel filter element replacement

Replace the fuel filter at specified intervals, before it is clogged with dust to adversely affect the fuel flow. Also, replace the fuel filter after the engine has fully been cooled. 1) Close the fuel cock of the water separator. 2) Remove the fuel filter using a filter wrench(customer procured). When removing the fuel filter, hold the bottom of the fuel filter with a piece of rag to prevent the fuel oil from dropping. If you spill fuel, wipe such spillage carefully. 3) Clean the filter mounting surface and slightly apply fuel oil to the gasket of the new fuel filter. 4) Install the new fuel filter manually turning until it comes into contact with the mounting surface, and tighten it further to 1/2 of a turn using a filter wrench. Tightening torque for 3TNV82A to 4TNV106(T): 20 24Nm(2.0 2.4kgfm)
Model 3TNV82A 4TNV88 4TNV98(T) 4TNV106(T) Applicable fuel filter Part No. 119802-55800 123907-55800
5) Bleed the fuel system. Refer to 2.2.3.(3) IMPORTANT: Be sure to use genuine part (super fine mesh filter). Otherwise, it results in engine damage, uneven engine performance and shorten engine life.
(3) Air cleaner cleaning and element replacement

Replace the air cleaner element periodically even if it is not damaged or dirty. When replacing the element, clean inside of the dust pan at the time. If having the air cleaner with double elements, do not remove the inner element. If the engine output is still not recover (or the dust indicator still actuates if having the air cleaner with a dust indicator) even though the outer element has replaced with new one, replace the inner element with new one.
36
2.2.6 Inspection every 1,000 hours or one year

Be sure to check the following points every 1,000 hours or one year operation, whichever comes first.
No. (1) (2) (3) (4) (5) Inspection Item Coolant water replacement Diaphragm assy inspection Turbocharger blower cleaning* Intake/exhaust valve clearance adjustment Fuel injection nozzle pressure inspection
(1) Coolant water replacement

Coolant water contaminated with rust or water scale reduces the cooling effect. Even when antifreeze agent (LLC) is mixed, the coolant water gets contaminated due to deteriorated ingredients. Replace the coolant water at least once a year. 1) Remove the radiator cap. 2) Loosen the drain plug at the lower portion of the radiator and drain the coolant water. 3) After draining the coolant water, tighten the drain plug. 4) Fill radiator and engine with coolant water. Refer to 3.4
Beware of scalding by hot water

Wait until the temperature goes down before draining the coolant water. Otherwise, hot water may splash to cause scalding.
37
(2) Diaphragm assy inspection

Inspect the diaphragm assy on the rocker arm cover every 1000 hours or 2 years. Refer to 4.2.4 point 6 for the function of the diaphragm. 1) Loosen screws, and remove a diaphragm assy, and check whether oil and so on doesnt enter between the diaphragm and the cover. If oil and so on enters into the diaphragm assy, the diaphragm doesnt work well. 2) Check the damages of the diaphragm rubber and the spring. If necessary, replace with new ones. [NOTICE] When a diaphragm is damaged, pressure control inside the crankcase becomes insufficient, and troubles such as combustion defect and so on occur. At lubricating oil replacement or lubricating oil supply, the amount of lubricating oil isnt to be beyond the standard upper limit. If the lubricating oil quantity is beyond the upper limit or an engine is operated beyond the allowable maximum angle of an engine, the amount of oil mist may be inducted in the combustion chamber and the oil hammer sometimes may occur.
38
(3) Turbocharger blower cleaning*

When engine speed seems sluggish or the exhaust color looks poor, the blades of the turbocharger-blower may be dirty. Wash the turbine blower in such a case. (a) General items 1) As for washing, use washing liquid and clear water. 2) Washing time is the time when about 10% of the boost pressure decreases more than that of usual operation state as a standard. 3) Disassemble and clean a turbocharger periodically because the whole of the turbocharger cant be cleaned in this method. (b) Washing point 1) A specified quantity of washing liquid/water is poured with a filler (ex. Oil sprayer) from the air inlet of the blower gradually (about then seconds) at the normal load (3/4-4/4) of an engine. And, perform this work at no-load after load running of the engine, if it is difficult to pour the liquid into the blower at load running.
Specified quantity of washing liquid/water Turbocharger model RHB31, RHB51 Injection amount, one time 20 cc
It causes an accident when large quantity of washing liquid is poured rapidly into a turbocharger. 2) Pour the same amount of clear water as washing liquid/water into the blower about 3-5 minutes later after the washing liquid/water injection and wash it. It causes an accident when large quantity of water is poured rapidly into a turbocharger. 3) Repeat the washing after then minutes when there is no change with the boost pressure or the exhaust gas temperature after washing. When there is no change at all even if it repeats 3-4 times, disassemble and maintain the turbocharger because of the cruel dirt of the blower or other causes. 4) Operate the engine at load for at least 15 minutes after washing, and dry.
39
(4) Intake/exhaust valve clearance adjustment

Make measurement and adjustment while the engine is cold. (a) Valve clearance measurement 1) Remove the rocker arm cover above cylinder head. 2) Set the No.1 cylinder in the compression TDC Turn the crankshaft to bring the piston of the No.1 cylinder to its compression top dead center while watching the rocker arm motion, timing scale and the top mark position of the crankshaft pulley. (Position where both the intake and exhaust valves are closed.) Notes: The crankshaft shall be turned clockwise as seen from the radiator side. The No.1 cylinder position is on the opposite side of the radiator and the ignition order shall be 1-3-4-2-1 at 180intervals. Since the intake and exhaust valve rocker arms are operated the same and there is a clearance between the arm and valve generally at the top dead center, the position can be checked by means of the play when the arm head is held with a hand. Also see that the crankshaft pulley top mark is positioned at zero on the timing scale. If there is no valve clearance, inspection in the disassembled state is necessary since the valve seat may be worn abnormally. 3) Valve clearance measurement In case of 2-valve cylinder head insert a thickness gage between the rocker arm and valve cap, and record the measured valve clearance. In case of 4-valve head insert a thickness gage between the rocker arm and the valve bridge, and record the measured valve clearance. (Use it as the data for estimating the wear state.) 4) Adjusting other cylinders In case of 4-cylinder engines, turn the crankshaft 180 and make adjustment for the No.3 cylinder. Then adjust the No.4 and No.2 cylinders in this order. The cylinder to be adjusted first does not have to be the No.1 cylinder. Select and adjust the cylinder where the piston is the nearest to the top dead center after turning, and make adjustment for other cylinders in the order of ignition by turning the crankshaft 180 each time. In case of 3-cylinder engines, turn the crankshaft 240 and make adjustment for the No.3 cylinder. Then adjust the No.2 cylinder in this order.
40
The cylinder to be adjusted first does not have to be the No.1 cylinder. Select and adjust the cylinder where the piston is the nearest to the top dead center after turning, and make adjustment for other cylinders in the order of ignition by turning the crankshaft 240 each time. The adjustment method of reducing the flywheel turning numbers (for reference): For 3 cylinder engines mark of the below Set No.1 cylinder to the compression T.D.C.and adjust the clearance of the table. Next, turn the flywheel once (the suction / exhaust valve of No.1 cylinder is in the position mark. of the overlap T.D.C. at this time), and adjust the clearance of the
Ignition order of 3 cylinder engines: 1 3 2 Cylinder No. 1 2 3 Valve Suction Exhaust Suction Exhaust Suction Exhaust No.1 The first time compression T.D.C No.1 The second time overlap T.D.C
For 4 cylinder engines Set No.1 cylinder to the compression T.D.C. and adjust the clearance of the bottom table. Next, turn the flywheel once, and adjust the clearance of the
Ignition order of 3 cylinder engines: 1 3 4 2 Cylinder No. 1 2 Valve Suction Exhaust Suction Exhaust No.1 compression T.D.C No.4 compression T.D.C 3 Suction Exhaust Suction 4
mark of the mark.
Exhaust The first time The second time
(b) Valve clearance inspection and adjustment 1) Loosen adjusting bolts In case of 2-valve cylinder head loosen the lock nut and adjusting screw, and check the valve for any inclination of valve cap, entrance of dirt or wear.
In case of 4-valve cylinder head loosen the lock nut and adjusting screw of rocker arm. Be careful that excessive tension isn't applied to the valve bridge, and loosen a locknut of valve bridge. [NOTICE] When loosening a locknut of a valve bridge, loosen the locknut while fixing the valve bridge with a wrench so that the valve may not lean.
41
Push the bridge head so that a valve bridge and two valve stem heads may contact each other uniformly, and adjust an adjusting bolt so that a gap of the valve stem head may become 0. Tighten a locknut after a valve bridge is fixed with a wrench.
2) Measuring valve clearance Insert a 0.2 or 0.3 mm thickness gage between the rocker arm and valve cap / valve bridge, and adjust the valve clearance. Tighten the adjusting screw.
Model 3TNV82A 98 4TNV106(T) mm Standard valve clearance 0.15 0.25 0.25 0.35
[NOTICE] When tightening a valve bridge locknut of 4-valve head, tighten a locknut after fixing a valve bridge with a wrench so that a bridge may not rotate and a valve may not lean. 3) Apply oil to the contact surface between adjusting screw and push rod. 4) Adjusting other cylinders In case of 4-cylinder engines turn the crankshaft 180 then and make adjustment for the No.3 cylinder. Then adjust the No.4 and No.2 cylinders in this order. The cylinder to be adjusted first does not have to be the No.1 cylinder. Select and adjust the cylinder where the piston is the nearest to the top dead center after turning, and make adjustment for other cylinders in the order of ignition by turning the crankshaft 180 each time. In case of 3-cylinder engines turn the crankshaft 240 then and make adjustment for the No.3 cylinder. Then adjust the No.2 cylinder in this order. The cylinder to be adjusted first does not have to be the No.1 cylinder. Select and adjust the cylinder where the piston is the nearest to the top dead center after turning, and make adjustment for other cylinders in the order of ignition by turning the crankshaft 240 each time.
42
(5) Fuel injection nozzle pressure inspection

Wear protective glasses when testing injection from the fuel injection valve. Never approach the injection nozzle portion with a hand. The oil jetting out from the nozzle is at a high pressure to cause loss of sight or injury if coming into careless contact with it.
(a) Injection pressure measurement

Model 3TNV82A TNV88 (CL ) 3TNV82A TNV88 (VM ) 4TNV94L 4TNV106(T) Standard MPa(kgf/cm2) 19.6-20.6 (200-210) 21.6-22.6 (220-230)
[NOTICE] As for the opening pressure of the brand-new fuel nozzle, about 0.5Mpa(5kgf/cm) declines by the engine operation for about 5 hours because of the initial wear-out of a spring etc. Therefore, adjust 0.5MPa(5kgf/cm) higher than the standard value of the above table when adjusting a new fuel nozzle of a spare part. Remove carbon deposit at the nozzle hole thoroughly before measurement. 1) Connect the fuel injection valve to the high pressure pipe of the nozzle tester. 2) Operate the nozzle tester lever slowly and read the pressure at the moment when the fuel injection from the nozzle starts. 3) If the measured injection pressure is lower than the standard level, replace the pressure adjusting shim with a thicker one.
Thickness of pressure adjusting shims mm 0.13, 0.15, 0.18, 0.4, 0.5, 0.8 Injection pressure adjustment The injection pressure is increased by approx. l.9 MPa(l9 kgf/cm2), when the adjusting shim thickness is increased by 0.l mm.
43
[Informative: Fuel injection valve structure]
(b) Spray pattern inspection After adjustment to the specified valve opening pressure, use a nozzle tester and check the spray pattern and seat oil-tightness.
Seat oil tightness check After injecting a few times, increase the pressure gradually. Hold the pressure for about 5 seconds at a little before the valve opening pressure of 1.96 MPa(20kgf/cm2), and check to see that oil does not drip from the tip end of the nozzle. If extreme oil leak from the overflow joint exists during injection by the nozzle tester, check after retightening. If much oil is leaking, replace the nozzle assembly.
44
Spray and injection states Operate the nozzle tester lever at a rate of once or twice a second and check no abnormal injection. If normal injection as shown below cannot be obtained, replace the fuel injection valve. No extreme difference in angle( ) No extreme injection angle difference( ) Finely atomized spray Excellent spray departure
(c) Nozzle valve sliding test Wash the nozzle valve in clean fuel oil. Place the nozzle body vertically and insert the nozzle into the body to about 1/3 of its length. The valve is normal if it smoothly falls by its own weight into the body. In case of a new nozzle, remove the seal peel, and immerse it in clean diesel oil or the like to clean the inner and outer surfaces and to thoroughly remove rust-preventive oil before using the nozzle. Note that a new nozzle is coated with rust-preventive oil and is pasted with the seal peel to shut off outer air.
(d) Nozzle punch mark
45
2.2.7 Inspection every 2000 hours or 2 years

Be sure to check the following points every 2,000 hours or two years operation, whichever comes first.
No. (1) (2) (3) (4) Inspection Item Coolant water path flushing and maintenance Fuel pipe and coolant water pipe inspection and maintenance Intake/exhaust valve seat lapping Fuel injection timing adjustment Fuel injection pump inspection and adjustment
(1) Coolant water path flushing and maintenance

Rust and water scale will accumulate in the cooling system through many hours of operation. This lowers the engine cooling effect. Oil coolers (attached to turbocharged engines and some of naturally aspirated engines) quickly deteriorate the lube oil. The cleaning and maintenance of the following parts are necessary in accordance with the coolant water replacement. Cooling system parts: radiator, cooling water pump, thermostat, cylinder block, cylinder head, oil cooler.
(2) Fuel pipe and coolant water pipe inspection and maintenance
Regularly check the rubber hoses of the fuel system and cooling water system. If cracked or degraded, replace them with new one. Replace the rubber hoses at least every 2 years even if 2,000 hours doesnt come.
(3) Intake/exhaust valve seat lapping

The adjustment is necessary to maintain proper contact of the valves and seats. Refer to 4.2.6 in Chapter 4.
(4) Fuel injection timing adjustment / Fuel injection pump inspection and adjustment
The fuel injection timing and the fuel injection pump are adjusted so that engine performance may become the best condition. As for the inspection and adjustment of the fuel pump, it is based on the service manual of the MP pump of the separate volume. The fuel injection timing is adjusted by the following procedure. As for the engine, which adopts a MP type fuel injection pump, the fuel injection angle i (note) is adjusted for the fuel injection timing adjustment, because the adjusting method of fuel injection timing like an inline fuel pump cant be applied. Note) The fuel injection angle i (cam angle) is the difference from the injection valve opening angle while the fuel injection pump being driven by a motor and the angle at the plunger lift 2.5mm of the fuel pump. And, as for the actual fuel injection angle i , the measured value is recorded on the pump body by each every fuel pump. The adjustment of fuel injection angle i In case that a fuel pump cover, installed with a gear case cover and the fuel pump are removed, and reassembled, the procedure of fuel injection angle adjustment is as follows. (As for the disassembly of a fuel injection pump, refer to 7.2.3 in chapter 7.) [NOTICE] Never loosen four flange bolts, which fasten a pump flange and a fuel pump drive gear at the time of the removal of the fuel pump. When it is loosened, the adjustment of the fuel injection timing becomes very difficult.
46
1) Before removing a fuel pump drive gear, make ID marks on the gearing part of the pump drive gear and the idle gear with paint and so on. 2) Make the mark-off line to the gear case precisely in accordance with the position of mark-off line of the fuel pump. 3) Before removing a fuel pump, put the standard mark of a sticker for fuel injection angle adjustment in accordance with the mark-off line of the fuel pump and paste it on the gear case.
4) Remove a fuel pump, and read the fuel injection angle recorded in that fuel pump.
5) Read the injection angle recorded on a reassembled fuel pump and calculate the difference from the injection angle of the disassembled fuel pump. (When re-installation does the same fuel pump, the angular difference is zero.) Fuel injection angle difference (cam angle) = (the fuel injection angle of a reassembled fuel pump) - (the fuel injection angle of a disassembled previous fuel pump) [NOTICE] Tell the fuel pump number, and inquire the injection angle of the pump when it is hard to find out. 6) Put the fuel pump on the gear case temporarily and install the drive gear on the cam shaft with checking the ID marks, which were put on the fuel pump drive gear and the idle gear at the time of the disassembling.
Tighten the installation nut of a pump drive gear. Tightening torque Model Nm(kgfm) 3TNV82A TNV88 4TNV94L/98/106(T) 78 88 (8 9) 113 123 (11.5 12.5) Lubricating oil application (thread portion, and seat surface) Not applied
47
7) Adjust the injection angle difference, calculated in the above 5), at 0.25 in the unit in the installation angle of the fuel pump while reading the mark (minimum 0.5 and cam angle) of the adjustment sticker. [NOTICE] Push down the fuel pump in the outside direction of the cylinder block at +1 degree when a injection angle difference is +1 degree. And, push it down to the cylinder block side when a difference is 1 degree. 8) Tighten the fuel pump installation nuts. (Supplementary explanation 1) The installation angle of the fuel pump is as follows.
Model 3TNV82A TNV88 4TNV94L/98/106(T) 4TNV106(T) Installation angle (deg.) 25 13 11.5
(Supplementary explanation 2) When fuel injection timing is advanced or delayed, the installation angle of the fuel pump is adjusted. When fuel injection timing is advanced for example at 2 degrees, loosen the nuts, which fix the fuel pump on the gear case, and turn the fuel pump body in the outside direction of the cylinder block at 1 degree, and tighten the pump installation nuts. And, when fuel injection timing is delayed, a pump is turned in that reverse direction.
48
2.3 Adjusting the no-load maximum or minimum speed

1) After warming the engine up, gradually raise the speed and set it at the no-load maximum revolution. 2) If the no-load maximum revolution is out of the standard, adjust it by turning the high idle limiting bolt. 3) Then set the no-load minimum speed by adjusting the low idle limiting bolt.
Standards Engine application class CL
Rating speed 1500 1800 2000 2200 2400
No-load maximum 1575-1625 1870-1920 2180-2230 2395-2445 2590-2640 2700-2750 2785-2835 2970-3020 3185-3235
(Unit: min-1) No-load minimum 1200 or more
800 or more (1100 or more for 4TNV106(T) )
VM
2500 2600 2800 3000
Note) The engine speed may differ from the above standard depending on an engine installed on a machine unit.
49
2.4 Sensor Inspection

2.4.1 Oil pressure switch
Disconnect the connector from the oil pressure switch. Keep the voltammeter probes in contact with the switch terminal and cylinder block while operating the engine. It is abnormal if circuit is closed.
2.4.2 Thermo switch

Place the thermo switch in a container filled with antifreeze or oil. Heat it while measuring the fluid temperature. The switch is normal if the voltammeter shows continuity when the fluid temperature is 107 113 deg C.
2.5 Water leak check in cooling water system

Check coolant water leakage from the cooling water system visually. If any problem is found, Inspect as follows. 1) Fill coolant water to the normal level in the radiator, and install the cap tester on the radiator. 2) Operate the manual pump to set the pressure to 0.09 0.015MPa (0.9 0.15kgf/cm2). If the cap tester pressure gage reading drops then, water is leaking from the cooling water system. Check the water leaking point.
50
2.6 Radiator cap inspection

Install the radiator cap on the cap tester. Set the tester pressure to 0.09 0.015MPa (0.9 0.15kgf/cm2) and see that the cap is opened. If the cap does not open, replace the cap since it is abnormal.
2.7 Thermostat Inspection

Place the thermostat in a container filled with water. Heat it while measuring the water temperature, and see that the thermostat is actuated at temperature of following table.
Model All models Valve opening Temperature (deg C)* 69.5 72.5 Full open lift (Temperature) (mm) 8 or more (85deg C)
* Valve opening temperature is carved on the flange.
51
2.8 Adjusting Operation

Perform the adjusting operation of a engine as follows after the maintenance job: 1) Supply the fuel oil, lubricating oil and coolant water. Note: Check the levels of the lubricating oil and coolant water again after test running (for about 5 minutes) and add as required. 2) Start the engine, and carry out idling at a low revolution (700 to 900 rpm) for a few minutes. 3) Run in the engine for about five minutes at the rated revolution (no-load). Check any water, fuel or oil leak and existence of abnormal vibration or noise. Also check the oil pressure, coolant water temperature and exhaust gas color. 4) Adjust the no-load minimum and maximum revolutions according to the specifications. 5) Perform loaded operation as required.
2.9 Long storage

Observe the following instructions when the engine is to be stored for a long period without operation: 1) Always drain coolant water in a cold season or before a long storage.(This is unnecessary when antifreeze is used.) [NOTICE] Negligence of water draining will cause the coolant water remaining inside the engine to be frozen and expanded to damage the engine parts. Water draining procedure a) Remove the radiator cap. b) Loosen the water draining cock under the radiator to drain water from the inside. c) Loosen the drain cock on the side surface of the cylinder to drain water from the inside. d) After draining water, tighten the radiator cap and drain plug and cocks. 2) Remove the mud, dust and oil deposit and clean the outside. 3) Perform the nearest periodic inspection before the storage. 4) Drain or fill the fuel oil fully to prevent condensation in the fuel tank. 5) Disconnect the battery cable from the battery negative (-) terminal. 6) Cover the silencer, air cleaner and electric parts with PVC cover to prevent water and dust from depositing or entrance. 7) Select a well-ventilated location without moisture and dust for storage. 8) Perform recharging once a month during storage to compensate for self-discharge.
52
3. Troubleshooting
3. TROUBLESHOOTING
3.1 Preparation before troubleshooting
If the signs of a trouble appear, it is important to lecture on the countermeasure and treatment before becoming a big accident not to shorten the engine life. When the signs of a trouble appear in the engine or a trouble occurs, grasp the trouble conditions fully by the next point and find out the cause of sincerity according to the troubleshooting. Then repair the trouble, and prevent the recurrence of the trouble. (e.g. 1) Whats the occurrence phenomenon or the trouble situation? 2) Investigation of the past records of the engine Check a client control ledger, and examine the history of the engine. Poor exhaust color )
Investigate the engine model name and the engine number. (Mentioned in the engine label.)
Examine the machine unit name and its number in the same way.
When was the engine maintained last time? How much period and/or time has it been used after it was maintained last time? What kind of problem was there on the engine last time, and what kind of maintenance was dane? 3) Hear the occurrence phenomenon from the operator of the engine in detail. 5W1H of the occurrence phenomenon : the investigation of when (when), where (where), who (who), what (what), why (why) and how (how) When did the trouble happen at what kind of time? Was there anything changed before the trouble? Did the trouble occur suddenly, or was there what or a sign? Was there any related phenomenon. .(e.g. Poor exhaust color and starting failure at the same time) 4) After presuming a probable cause based on the above investigation, investigate a cause systematically by the next troubleshooting guide, and find out the cause of sincerity.
53
3. Troubleshooting
3.2 Quick Reference Table for Troubleshooting

The following table summarizes the general trouble symptoms and their causes. If any trouble symptom occurs, take corrective action before it becomes a serious problem so as not to shorten the engine service life.
High knocking sound during combustion Trouble symptom Starting failure Engine starts but stops soon. Exhaust smoke Poor Insufficient exhaust engine output color Exhaust color During work Hunting Difficulty in returning to low speed Lubricating oil Cooling water Air intake
Excessive fuel consumption
Uneven combustion sound
Exhaust temperature rise
Abnormal engine sound
Excessive consumption
Low water temperature
Large engine vibration
Engine does not start.
Low L.O. pressure
Much blow-by gas
Mixture with water
Corrective action
Dilution by fuel oil
Pressure drop
Improper clearance of intake/exhaust valve Compression leakage from valve seat Seizure of intake/exhaust valve Blowout from cylinder head gasket Seized or broken piston ring Worn piston ring, piston or cylinder Seized crankpin metal or bearing Engine system Improper arrangement of piston ring joints Reverse assembly of piston rings Worn crankpin and journal bearing Loosened connecting rod bolt Foreign matter trapped in combustion chamber Excessive gear backlash Worn intake/exhaust valve guide Defective governor Improper open/close timing of intake/exhaust valves
Little
Cause
Pressure rise
During idling
During work
Overheat
Ordinary
White
White
Much
Black
Black
None
Adjust the valve clearance. (See 2.2.6 in Chapter2.) Lap the valve seat. (See 4.2.6 in Chapter4.) Correct or replace. Replace the gasket. (See 4.2.2-11) in Chapter4.) Replace the piston ring. (See 4.2.2-5)10) in Chapter4.) Perform honing and use oversize parts. (See 4.4.5-1)4) and 4.4.6 in Chapter4.) Repair or replace. Correct the ring joint positions. (See 4.4.4-6 in Chapter4.) Reassemble correctly. (See 4.4.4-6 in Chapter4.) Measure and replace. (See 4.4.5-2) in Chapter4.) Tighten to the specified torque. (See 4.4.4-2 in Chapter4.) Disassemble and repair. Adjust gear meshing. (See 4.3.4-2 in Chapter4.) Measure and replace. (See 4.2.5-2) and 4.2.7 in Chapter4.) Make adjustment. Adjust the valve clearance. (See 2.2.6-3) in Chapter2.)
Fouled blower Turbocharger Waste gate malfunction Worn floating bearing
Wash the blower. Disassemble and inspect. Disassemble and inspect.
54
3. Troubleshooting
High knocking sound during combustion
Low L.O. pressure
Much blow-by gas
Mixture with water
Exhaust smoke
Engine starts but stops soon. Engine does not start.
Exhaust color
During work
Difficulty in returning to low speed
Trouble symptom
Starting failure
Poor Insufficient exhaust engine output color
Hunting
Lubricating oil
Cooling water
Air intake
Corrective action
Pressure drop
Cause Excessive cooling effect of radiator Cooling Water System Insufficient cooling effect of radiator Insufficient coolant water level Cracked water jacket Slackened fan belt Defective thermostat
Pressure rise
During idling
During work
Overheat
Ordinary
White
White
Much
Black
Black
None
Little
Defective thermostat (kept closed) (See 2.2.7 in Chapter2.) Defective thermostat (kept opened)(See 2.2.7 in Chapter2.) or slipping fan belt (See 2.2.2-2) in Chapter2.) Check water leakage from cooling water system. (See 2.2.1-4) in Chapter2.) Repair or replace. Adjust the belt tension. (See 2.2.2-2) in Chapter2.) Check or replace. (See 2.2.7 in Chapter2.)
Improper properties of lubricating oil Lubricating System Leakage from lubricating oil piping system Insufficient delivery capacity of trochoid pump Clogged lubricating oil filter Defective pressure regulating valve Insufficient lubricating oil level
Use proper lubricating oil. (See 1.3.2 in Chapter1.) Repair. Check and repair. (See 5.5 in Chapter5.) Clean or replace. Clean, adjust or replace. Add proper lubricating oil. (See 2.2.1-3) in Chapter2.)
Too early timing of fuel injection pump Too late timing of fuel injection pump Improper properties of fuel oil Water entrance in fuel system Clogged fuel filter Fuel system Air entrance in fuel system Clogged or cracked fuel pipe Insufficient fuel supply to fuel injection pump Uneven injection volume of fuel injection pump Excessive fuel injection volume Poor spray pattern from fuel injection nozzle Priming failure Clogged strainer at feed pump inlet
Check and adjust. (See 2.2.7-4) in Chapter2.) Check and adjust. (See 2.2.7-4) in Chapter2.) Use proper fuel oil. (See 1.3.1 in Chapter1.) Perform draining from the fuel filter. (See 2.2.3 and 2.2.5 in Chapter2.) Clean or replace. (See 2.2.5 in Chapter2.) Perform air bleeding. (See 2.2.3 in Chapter2.) Clean or replace. Check the fuel tank cock, fuel filter, fuel pipe, and fuel feed pump. Check and adjust. Check and adjust. Check and adjust. (See 2.2.6 in Chapter2.) Foreign matter trapped in the valve inside the priming pump. (Disassemble and clean.) Clean the strainer.
55
3. Troubleshooting
High knocking sound during combustion
Low L.O. pressure
Much blow-by gas
Mixture with water
Exhaust smoke
Engine starts but stops soon. Engine does not start.
Exhaust color
During work
Difficulty in returning to low speed
Trouble symptom
Starting failure
Poor Insufficient exhaust engine output color
Hunting
Lubricating oil
Cooling water
Air intake
Corrective action
Pressure drop
Cause Clogged air filter Air/Exhaust Gas System Engine used at high temperatures or at high altitude Clogged exhaust pipe
Pressure rise
During idling
During work
Overheat
Ordinary
White
White
Much
Black
Black
None
Little
Clean. (See 2.2.4 in Chapter2.) Study output drop and load matching. Clean.
Starting motor defect Alternator defect Electrical System Open-circuit in wiring Battery voltage drop
Repair or replace. (See Chapter8.) Repair or replace. (See Chapter9.) Repair. (See Chapter10.) Inspect and change the battery. (See 2.2.3 in Chapter2.)
56
3. Troubleshooting
3.3 Troubleshooting by measuring Compression Pressure

Compression pressure drop is one of major causes of increasing blowby gas (lubricating oil contamination or increased lubricating oil consumption as a resultant phenomenon) or starting failure. The compression pressure is affected by the following factors: 1) Degree of clearance between piston and cylinder 2) Degree of clearance at intake/exhaust valve seat 3) Gas leak from nozzle gasket or cylinder head gasket In other words, the pressure drops due to increased parts wear and reduced durability resulting from long use of the engine. A pressure drop may also be caused by scratched cylinder or piston by dust entrance from the dirty air cleaner element or worn or broken piston ring. Measure the compression pressure to diagnose presence of any abnormality in the engine.
(1) Compression pressure measurement method

1) After warming up the engine, remove the fuel injection pipe and valves from the cylinder to be measured. 2) Crank the engine before installing the compression gage adapter. *1) Perform cranking with the stop handle at the stop position (no injection state). *2) See 12.2-18 in Chapter 12 for the compression gage and compression gage adapter. 3) Install the compression gage and compression gage adapter at the cylinder to be measured. *1)Never forget to install a gasket at the tip end of the adapter. 4) With the engine set to the same state as in 2)*1), crank the engine by the starter motor until the compression gage reading is stabilized.
(2) Standard compression pressure

Engine compression pressure list (reference value) Compression pressure at 250 min-1 Engine mode MPa (kgf/cm2) Standard Limit 3TNV82A 3/4TNV84 3/4TNV84T TNV88 106(T) 3.16 0.1 (31 1) 3.24 0.1 (33 1) 2.94 0.1 (30 1) 3.43 0.1 (35 1) 2.45 0.1 (25 1) 2.55 0.1 (26 1) 2.45 0.1 (25 1) 2.75 0.1 (28 1) 0.2 0.3 (2 3) Deviation among cylinders MPa (kgf/cm2)
57
3. Troubleshooting
(3) Engine speed and compression pressure (for reference)
(4) Measured value and troubleshooting

When the measured compression pressure is below the limit value, inspect each part by referring to the table below.
No. 1 2 3 4 Intake/exhaust vale Valve seat Piston Piston ring Cylinder Gas leak due to worn valve seat or foreign matter trapping Sticking valve Gas leak due to scratching or wear Valve clearance valve timing Cylinder head gasket Item Air cleaner element Cause Clogged element Broken element Defect at element seal portion Excessive or no clearance Incorrect valve clearance Gas leak from gasket Corrective action Clean the element. Replace the element. Adjust the valve clearance. (See 3.5 in Chapter 3.) Adjust the valve clearance. (See 3.5 in Chapter 3.) Replace the gasket. Retighten the cylinder head bolts to the specified torque. (See 4.2(2)12) in Chapter 4.) Lap the valve seat. (See 4.2(6) in Chapter 4.) Replace the intake/exhaust valve. Perform honing and use an oversized part. (See 4.4(5)-(5-1), (5-4) and (6) in Chapter 4.)
58
4. Disassembly, Inspection and Reassembly of Engines

4.1 Complete disassembly and reassembly
4.1.1 Introduction
Make preparation as follows before starting engine inspection and service: 1) Fix the engine on a horizontal base. Be sure to fix the engine securely to prevent injury or damage to parts due to falling during the work. 2) Remove the coolant water hose, fuel oil pipe, wire harness, control wires etc. connecting the driven machine and engine, and drain coolant water, lubricating oil and fuel. 3) Clean soil, oil, dust, etc. from the engine by washing with solvent, air, steam, etc. Carefully operate so as to prevent any foreign matter from entering the engine. Always wear glasses or other protectors when using compressed air or steam to prevent any foreign matter from getting in the eyes. [NOTICE] Any part which is found defective as a result of inspection or any part whose measured value does not satisfy the standard or limit shall be replaced. Any part predicted to dissatisfy the standard or limit before the next service as estimated from the state of use should be replaced even when the measured value then satisfies the standard or limit.
59
4.1.2 Special service tools

(1) Special Tools
No. Tool name Valve guide tool (for extracting valve guide) Applicable model and tool size Model 3TNV82A 4TNV94L 98(T) 4TNV106(T) 4TNV84 3TNV84(T) 3/4TNV88 4TNV84T L1 20 20 20 L2 75 75 75 d1 6.5 7.5 5.5 d2 10 11 9 Illustration
Locally manufactured Valve guide tool (for inserting valve guide) Model 3TNV82A 4TNV84 3TNV84(T) 3/4TNV88 4TNV84T 4TNV94L 98(T) 4TNV106(T) L1 12 15 8.5 7 13.6 L2 60 65 60 60 65 d1 13 14 11 13 13 d2 19 20 17 16 16
Locally manufactured Connecting rod bushing replacer (for removal / installation of connecting rod bushing) 3 Model 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) L1 25 20 20 20 L2 85 100 100 100 d1 23 26 30 37 d2 26 29 33 40
0.3 0.3 Allowance: d1 0.6 d2 0.6
Locally manufactured Valve spring compressor (for removal / installation of valve spring)
Code No. 129100-92630
60
No.
Tool name Stem seal inserter (for inserting stem seal)
Applicable model and tool size

Model 3TNV82A 4TNV84 3TNV84(T) 4TNV88 4TNV84T 4TNE94L 98 4TNE106(T) d1 15.2 16.2 12.9 15.2 15.2 d2 21 22 19 21 21 d3 12 13.5 11.5 12 12 L1 15.8 18.8 10.0 11.8 15.5 L2 65 65 65 65 65 L3 4 4 4 4 4
Illustration
Locally manufactured Filter wrench (for removal / installation of L.O. filter) Camshaft bushing tool (for extracting camshaft bushing)
Available on the market
Model TNV82A 88 4TNV94L 98 4TNV106(T) L1 18 18 18 L2 70 70 70 d1 45 50 58 d2 48 53 61
0.3 0.3 Allowance: d1 0.6 d2 0.6
Locally manufactured Flex-Hone (For re-honing of cylinder liner)

Cylinder bore () 78 84 83 95 89 101 95 108
Model TNV82A
Parts No. 129400-92420 129400-92430 129400-92440 129400-92450
TNV88 4TNV94L 4TNV98 4TNV106(T)
Piston insertion tool (for inserting piston) Piston ring replacer (for removal / installation of piston ring) Crankshaft pulley installing tool
Code No. 95550-002476 The above piston insertion tool is applicable to 60-125 mm diameter pistons.
10
Available on the market
11
Locally manufactured (for 4TNV94L) (Refer to 4.3.6 in detail)
61
(2) Measuring instruments

No. Instrument name Application Measurements of shaft bending, and strain and gap of surfaces Illustration
Dial gage
Measurements of narrow or deep portions that cannot be measured by dial gage 2 Test indicator
For holding the dial gage when measuring using a dial gage, standing angles adjustable 3 Magnetic stand
For measuring the outside diameters of crankshaft, pistons, piston pins, etc. 4 Micrometer
For measuring the inside diameters of cylinder liners, rod metal, etc. 5 Cylinder gage
For measuring outside diameters, depth, thickness and width 6 Calipers
For measuring of valve sink 7 Depth micrometer
For measuring valve spring inclination and straightness of parts 8 Square
62
No.
Instrument name
Application For measuring shaft bend
Illustration
V-block
For tightening nuts and bolts to the specified torque 10 Torque wrench
For measuring gaps between ring and ring groove, and shaft joints during assembly 11 Thickness gage
For checking water leakage
12
Cap tester
For checking concentration of antifreeze and the battery electrolyte charge status 13 Battery coolant tester
For measuring injection spray pattern of fuel injection nozzle and injection pressure 14 Nozzle tester
For measuring temperatures
15
Digital thermometer
63
No.
Instrument name
Application For measuring revolution by contacting the mortise in the revolving shaft
Illustration
Contact type
16
Speedometer
For measuring revolution by sensing the reflecting mark on the outer periphery of the revolving shaft Photoelectric type
For measuring resistance, voltage and continuity of electrical circuits 17 Circuit tester
For measuring compression pressure Code No. TOL-97190080 18 Compression gage kit
64
4.1.3 Complete disassembly

Peripheral parts such as air cleaner, muffler and radiator differ in installation and types for each application. Therefore, description in this Chapter is started with the steps to be taken just after the peripheral parts have been removed.
Step 1 Removal Parts 1) Thoroughly remove sand, dust, dirt and soil from the surface of the engine. 2) Drain coolant water and lubricating oil from the engine. 1) Remove turbocharger and exhaust manifold. 2) Remove intake manifold and surge tank. Remarks
1) Close the fuel cock valve of the fuel tank. 2) Remove high-pressure fuel pipe. 3) Remove fuel return pipe. 4) Loosen the tightening nut on fuel injection nozzle retainer and extract the retainer and fuel injection nozzle. *) Fuel injection nozzle for Indirect injection system is screwed type. 1) Remove rocker arm cover assembly.
1) If nozzle seat is left on the cylinder head, remove the cylinder head before extracting nozzle seat. 2) To prevent dust from entering fuel injection nozzle, fuel injection pump and high-pressure fuel pipe, seal their respective threads with a tape or the like. 3) Whenever extracting fuel injection nozzle, replace nozzle protector with a new one.
4 1) Remove valve rocker arm shaft assembly. 2) Remove push rod. 1) Attach a tag to push rod for each cylinder No. to put the push rod in order. 2) Remove valve cap from the intake/exhaust valve head. 3) Note that tappet of the indirect injection system can be removed at the same time when push rod is extracted. 4) Attach a tag to tappet for each cylinder No. to put the tappet in order. 1) Never turn down alternator vigorously toward the cylinder block. Otherwise, your finger may be nipped and alternator broken.
1) Remove fan mounting bolt, and then remove fan. 2) Loosen adjusting bolt for the V-belt adjuster, and then remove V-belt. 3) Remove alternator. 4) Remove the spacer for cooling fan and V-pulley. 1) Remove lubricating oil filter assembly. 2) Extract dipstick form the oil dip-stick hole.
1) Disconnect fuel return pipes to. 2) Remove fuel filter.
65
Step 9
Removal Parts 1) Disconnect coolant water pipe from the cooling water pump. 2) Remove thermostat assembly. 3) Remove cooling water pump. 1) Remove cylinder head tightening bolt. 2) Remove cylinder head assembly. 3) Remove cylinder head gasket.
Remarks
1) Lay a cardboard or the like on the floor and place cylinder head assembly on it so as not to damage the combustion surface. 2) Order of loosening the cylinder head tightening bolts.
10
3) To remove the intake/exhaust valves from cylinder head assembly, take the following steps. a) Using a valve spring compressor (see Chapter 5, 5-1), compress valve spring and remove valve cotter. b) Remove valve retainer and valve spring. c) Remove intake valve and exhaust valve. 1) Remove crankshaft V-pulley clamping bolt. 2) Using a puller, extract crankshaft V-pulley. 1) Extract crankshaft V-pulley by hitting the bolt of the puller using a plastic hammer or the like. 1) Never fail to removes stiffner bolt at the center of the gear case. 2) When removing the gear case, carefully protect oil seal from damage. 1) Before removing fuel injection pump, make sure of the position of the arrow of the pump body for adjusting fuel injection timing as well as the position of the scribed line of the gear case flange. (Applies only to direct injection system.)
11
12
1) Remove oil pan mounting bolt under gear case. 2) Remove gear case mounting bolt. 3) Remove gear case. 1) Remove the nut from fuel injection pump drive gear. Extract fuel injection pump drive gear using a puller.
13
66
Step 14
Removal Parts 1) Remove lubricating oil pump.
Remarks
15
1) Remove starting motor from flywheel housing sing.
16
1) Remove flywheel mounting bolt. 2) Remove flywheel.
1) Carefully protect the ring gear from damage mage.
17
1) Remove flywheel housing. 2) Remove oil seal case with a screwdriver or the like by utilizing grooves on both sides of oil seal case. 1) Remove oil pan and spacer.
1) Carefully protect the oil seal from damage.
18
1) Put the cylinder block with the attaching surface of the cylinder head facing down. 2) Carefully protect the combustion surface of the cylinder block from damage. 3) For indirect injection system, be careful to the possibility of the tapped to drop off when the cylinder block is turned upside down, because the tappet is cylindrical in shape. 1) Turn the cylinder block aside and carefully prevent tappet from jamming on the cam. 2) Preheat camshaft gear and camshaft assembly to 180 200 which are shrink fitted, before removing them.
19
1) Remove idle gear shaft, and then remove idle gear. 2) Remove mounting bolt of thrust bearing through the hole of the camshaft gear. Remove camshaft assembly. 1) Remove gear case flange.
20 1) Remove lubricating oil strainer. 21 1) Remove crankpin side cap of the connecting rod. While turning crankshaft, place piston in the bottom dead center (BDC). 22 1) Before extracting piston, remove carbon deposits from the upper wall of the cylinder using fine sandpaper, while taking care not to damage the inner surface of the cylinder. 2) Make sure than cap No. of connecting rod agrees with cylinder No. 3) Take care not to let crankpin metal fall when removing connecting rod crankpin side cap.
67
Step
Removal Parts 1) Remove main bearing cap bolt. While shaking main bearing cap, remove main bearing cap together with lower main bearing metal. 2) Extract crankshaft, taking care not to damage it. 3) Remove upper main bearing metal.
Remarks 1) Before extracting crankshaft, measure the side gap around it.
23 Apply a dial gauge to the end of crankshaft. Force the crankshaft on both sides in the axial direction to measure the thrust gap. Alternatively, insert a thickness gauge directly between the base thrust metal and the thrust surface of the crankshaft to measure the gap. If the limit size is exceeded, replace the thrust metal with a new one. Thrust gap (All models) 2) Notice on the removal of thrust metal. a) When removing thrust metal, ascertain the position and direction where thrust metal is installed in relation to the cap. b) Make sure that the thrust metal groove is outward in relation to the cap. 1) Remove piston and connecting rod assembly. 1) To selectively remove a desired piston and connecting rod assembly without extracting crankshaft, take the steps itemized below: a) Remove carbon deposits from the upper wall of the cylinder using fine sandpaper, taking care not to damage the inner surface of the cylinder. b) While turning the crankshaft, with the connecting rod cap removed, raise the piston up to the top dead center (TDC). c) Extract the piston/connecting rod assembly while tapping the connecting rod at the large end with the handle of a plastic hammer or the like.
24
2) Remove tappet. 25
68
4.1.4 Precautions before and during reassembly

To reassemble engine components, reverse the procedure of disassembly. However, follow the precautions below and the precautions from in chapter 4 to in chapter 7 particularly before and during reassembly.
(1) Cleaning the component

Use particular care to clean the cylinder block, cylinder head, crankshaft, and camshaft. they are free from chips, dust, sand, and other foreign matter. Ensure that
(2) Parts to be replaced during reassembly

Be sure to replace the following parts with new ones during assembly. Valve stem seal Head gasket packing Nozzle protector and nozzle seat of the fuel injection valve Various copper packing, O-rings and gasket packing.
4.1.5 Adjusting operation

Make sure to perform adjusting operation after completing reassembly. Refer to section 2.5 in chapter 2 for the operation procedure.
69
4.2 Cylinder Head: Disassembly, Inspection and Reassembly

4.2.1 Components (2-valve cylinder head)
4.2.2 Disassembly procedure:

Disassemble in the order of the numbers shown in the illustration. 1) Remove the alternator assy. (Point1) 2) Remove the fan, pulley and V belt. 3) Remove the thermostat case. (Point2) 4) Remove the fuel filter and fuel oil piping. (Point3) 5) Remove the oil level gage assy. 6) Remove the oil filter. (Point4) 7) Remove the fuel injection pipes. (Point5) 8) Remove the intake manifold assy. 9) Remove the exhaust manifold assy. 10) Remove the rocker arm cover Assy. 11) Remove the rocker shaft assy, push rods and valve caps. (Point6) 12) Remove the cylinder head assy and head gasket. (Point7) 13) Remove the fuel injection valves and fuel return pipe. (Point8) 14) Remove the intake/exhaust valves, stem seals and valve springs. (Point9) 15) Remove the rocker arms from the rocker shaft.
70
4.2.3 Reassembly procedure:

Reverse order of the disassembly procedure.
71
4.2.4 Servicing points

Point1 [Disassemble] Loosen the mounting bolt while supporting the alternator. Do not tilt the alternator toward the cylinder block in haste since it may damage the alternator or pinch a finger. [Reassemble] The belt deflection shall be checked according to 2.2.2. in Chapter2. [Reassemble] Replace the belt with a new one if cracked, worn or damaged. Carefully prevent the belt from being smeared with oil or grease.
Point2 [Reassemble] Check the thermostat function. (See3.9 in Chapter 3 for the check procedure.) Pont3 [Reassemble] Replace the fuel filter element with a new one. [Disassemble] Cover the fuel pipe opening with tape to prevent intrusion of foreign matters. Point4 [Reassemble] Replace the oil filter with a new one. After fully tightening the filter manually, retighten it with a filter wrench (see 11.1-6 in Chapter 11) by 3/4 turn. Point5 [Disassemble] Cover the fuel injection pipe and pump inlets and outlets with tape or the like to prevent intrusion of foreign matters.
72
Point6 1) Removing pipe seals of 4 valve head. [Disassemble] Take off a rocker arm cover in case of 4 valve head after removing fuel injection pipes and pipe seals. [NOTICE] Attention is necessary because a fuel nozzle is caught in a pipe seal and the pipe seal is damaged when a rocker arm cover is lifted with a pipe seal sticking to the rocker arm cover. Insert a minus driver in the slit part of the rocker arm cover, and remove it when removing a pipe seal. [Reassemble] Replace the used pipe seal with a new one when removing a pipe seal.
2) Breather system (A reductor to intake air system of blowby gas) Emitting blowby gas is harmful to natural environment. Therefore blowby gas reductor is adopted to TNV series naturally- aspirated engines as breather system (Turbocharged engines emitblowby gas). The system of model 3/4TNV84 is shown as a representative of that breather system in the right figure. Some of the combustion gas passes through the clearance between the cylinder and the piston, piston ring, and flows to the crankcase. This is said as blowby gas. While it passes into the cylinder head and the rocker arm cover, the blowby gas mixes with splash oil, and becomes oil mist-blowby gas mixes with splash oil, and becomes oil mist-blowby gas ith passing through the baffle plate inside a rocker arm cover. And it passes through a diaphragm assy, and a intake manifold, and is reduced in the combustion chamber. Pressure inside a crankcase is controlled by the function of the diaphragm assy, and suitable amount of blowby gas is reduced in intake air system. [Disassemble] When a rocker arm cover is taken off, check whether oil or the like enter the diaphragm space from a small hole on the side of a diaphragm cover or not without disassembling the diaphragm.
73
[NOTICE] 1) When a diaphragm is damaged, pressure control inside the crankcase becomes insufficient, and troubles occur. When the internal pressure of the crankcase decreases too much due to the damage of a spring, much blowby gas containing oil is reduced in intake air system, and it may cause the combustion defect by the early dirt of the intake valve or the urgent rotation of the engine by the oil burning. When pressure progresses in the crank case too much due to the wrong operation of the diaphragm and so on, it is considered that oil leakage from the joint of a oil pan, a oil seal and so on will occur. When a diaphragm is damaged, blowby is discharged from the breathing hole on the side of diaphragm cover, and not reduced in the intake manifold. Therefore, be careful of the diaphragm trouble. 2) At lubricating oil replacement or lube oil supply The amount of lubricating oil isn't to be beyond the standard upper limit (in the engine horizontality, the upper limit mark of the dip stick). Since the blowby gas reductor is adopted, be careful that the amount of oil mist may be inducted in the combustion chamber and the oil hammer sometimes may occur, when the lubricating oil quantity is beyond the upper limit or an engine is operated beyond the allowable maximum angle of an engine. [Reassembly] Replace the diaphragm with new one, when it is damaged. Point7 [Disassemble] Keep the removed push rods by attaching tags showing corresponding cylinder Nos. [Reassemble] Always apply oil to the contact portions of the push rods and clearance adjusting screws. Point8 [Disassemble] Loosen the cylinder head bolts in two steps in the illustrated order. Place the cylinder head assy on a paper board to prevent the combustion face from any damage. [Reassemble] Remove the head gasket with a new one. Uniformly install the head bolts manually after applying oil on the threaded and seat portions They shall be tightened in two steps in the reverse of the order for disassembly. Tightening torque
TNV82A 30.0 34.0 (3.1 3.5) 61.7 65.7 (6.3 6.7) 4TNV94L/98 49.0 58.8 (5.0 6.0) 103.1 112.9 (10.5 11.5) Nm(kgf m) TNV84-88 41.1 46.9 (4.2 4.8) 85.3 91.1 (8.7 9.3) 4TNV106(T) 88.3 98.1 (9.0 10.0) 188.0 197.8 (19.0 20.0)
First step Second step
First step Second step
74
Point9 [Disassemble] Carefully remove the fuel injection valve so as not to leave the top end protector from being left inside the cylinder. [Reassemble] Replace the fuel injection valve protector with a new one. Point10 [Disassemble] When removing each intake/exhaust valve from the cylinder head, use a valve spring compressor (see 11.1-4 in Chapter 11) and compress the valve spring and remove the valve cotter.) Keep each removed intake/exhaust valve after attaching a tag showing the corresponding cylinder No. If cotter burr is seen at the shaft of each intake/exhaust valve stem, remove it with an oilstone and extract the valve from the cylinder head. [Reassemble] Replace the stem seal with a new one when an intake/exhaust valve is disassembled. Carefully install each valve after oil application so as not to damage the stem seal. Different stem seals are provided for the intake and exhaust valves. Do not confuse them since those for exhaust valves are marked with yellow paint. After assembling the intake/exhaust valve, stem seal, valve spring, seat, and cotter, tap the head of the valve stem lightly for settling. Do not forget to install the valve cap.
75
4.2.5 Parts Inspection and measurement

(1) Cylinder head
Clean the cylinder head, mainly the combustion surface, valve seats and intake/exhaust ports, remove carbon deposit and bonding agent, and check the surface state. (a) Appearance check Check mainly discoloration and crack. If crack is suspected, perform color check.
(b) Combustion surface distortion Apply a strait-edge in two diagonal directions and on four sides of the cylinder head, and measure distortion with a thickness gage.
mm Standard Distortion 0.05 or less Limit 0.15
(c) Valve sink Measure with the valve inserted to the cylinder head.
mm Standard Intake 3TNV82A (2-valve head) Exhaust 4TNV84 3TNV84(T) 3/4TNV88 (2-valve head) 4TNV84T 4TNV94/98(T) (4-valve head) Intake Exhaust Intake Exhaust 0.35 0.55 0.30 0.50 0.30 0.50 0.30 0.50 0.36 0.56 0.35 0.55 0.5 0.7 0.7 0.9 Limit 0.8 0.8 0.8 0.8 0.8 0.8 1.0 1.2
Intake 4TNV106(T) (4-valve head) Exhaust
(d) Seat contact Apply a thin coat of minium on the valve seat. Insert the valve in the cylinder and push it against the seat to check seat contact.
Standard: Continuous contact all around
76
(2) Valve guide

Mainly check damage and wear on the inside wall. Apply the service part code when replacing a part.
Model 3TNV82A (2-valve) 4TNV84 3TNV84(T) 3/4TNV88 (2-valve) 4TNV84T (4-valve) 4TNV94L 4TNV98(T) (4-valve) 4TNV106(T) (4-valve) Suction Exhaust Suction Exhaust Suc./Exh. Suc./Exh. Suction Exhaust Service part code 124060-11800 119802-11810 120130-11860 129150-11810 119717-11800 129907-11800 123907-11800 123907-11810
Valve stem clearance

Model Part name Intake value 3TNV82A (2-valve head) Exhaust value Place Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Guide I.D. Stem O.D. Clearance Standard 7.000 7.015 6.945 6.960 0.040 0.070 7.000 7.015 6.940 6.955 0.045 0.075 8.010 8.025 7.955 7.975 0.035 0.070 8.015 8.030 7.955 7.970 0.045 0.075 6.000 6.015 5.960 5.975 0.025 0.055 6.000 6.015 5.945 5.960 0.040 0.070 7.000 7.015 6.945 6.960 0.040 0.070 7.000 7.015 6.940 6.955 0.045 0.075 7.008 7.020 6.960 6.975 0.033 0.060 7.008 7.020 6.945 6.960 0.048 0.075 Limit 7.08 6.90 0.18 7.08 6.90 0.18 8.10 7.90 0.18 8.10 7.90 0.18 6.08 5.90 0.15 6.08 5.90 0.17 7.08 6.90 0.17 7.08 6.90 0.17 7.08 6.92 0.16 7.08 6.90 0.18
4TNV84 3TNV84(T) 3/4TNV88 (2-valve head)
Intake value
Exhaust value
Intake value 4TNV84T (4-valve head) Exhaust value
4TNV94L 4TNV98(T) (4-valve head)
Intake value
Exhaust value
Intake value 4TNV106(T) (4-valve head) Exhaust value
77
(3) Intake/exhaust valve

Mainly clean and check damage and wear at the valve stem and seat. (a) Seat contact: See (1)-(d) above. (b) Stem outside diameter: See (2) above. (c) Valve head thickness
Model TNV82A 88 Part Intake Exhaust Intake Exhaust Intake Exhaust Standard 1.34 1.45 1.71 1.65 2.00 2.00 mm Limit 0.50 0.50 1.00 1.00 1.30 1.30
4TNE94 95
4TNE106(T)
(d) Valve stem bend

mm Limit 0.01
(e) Overall length

Standard 3TNV82A TNV84 88 4TNV94 98 4TNV106(T) Intake/Exhaust Intake/Exhaust Intake/Exhaust Intake/Exhaust 115 126 114.5 125.5 ? mm Limit
(4) Valve spring

Mainly inspect damage and corrosion.
Free length standard 3TNV82A TNV84 88 4TNV94 98 4TNV106(T) 44.4? 42.0? 47.5 50.6 mm Inclination limit 1.2
1.2
78
(5) Valve rocker arm

Mainly inspect valve head cap contact surface, inside surface defects and wear. Slight surface defects shall be corrected with an oilstone.
Model Items Arm hole diameter Shaft O.D. Clearance Arm hole diameter Shaft O.D. Clearance Standard 16.00 16.02 15.97 15.98 0.016 0.054 18.50 18.52 18.47 18.49 0.01 0.05 mm Limit 16.07 15.94 0.13 18.57 18.44 0.13
TNV82A 88
4TNV94/98(T) 4TNV106(T)
(6) Rocker arm shaft

Mainly inspect seizure and wear at the surface in sliding
contact with the arm. The rocker shaft diameter shall be as specified in (5.5) above.
(7) Push rod

Mainly inspect the surface in contact with the tappet and adjusting screw. Slight defects shall be corrected with an oilstone.
Bend limit 0.03mm or less
(8) Valve clearance adjusting screw

Mainly inspect the surface in contact with the push rod.
Slight defects shall be corrected with an oilstone. (9) Rocker arm spring
Mainly inspect surface defects and corrosion.
79
4.2.6 Valve seat correction

[NOTICE] Always check the oil clearance between the valve and valve guide before correcting the valve seat. If it exceeds the limit, replace the valve or valve guide first to make the clearance satisfy the standard. After correction, wash the valve and the cylinder head sufficiently with diesel oil to remove all grinding powder or compound. 1) If the seat surface is slightly roughened: perform [A] and [B] below. [A]: Lap the valve and seat with a mixture of valve compound and engine oil. [B]: Lap with engine oil only. 2) If the seat is heavily roughened but the width is almost normal, correct with a seat grinder or seat cutter first. Then perform lapping [A] and [B].
intake Seat cutter angle 120 Exhaust 90
3) If the seat is heavily roughened and the width is much enlarged, grind the seat inner surface with a seat grinder whose center angle is 40, then grind the seat outer surface with a grinder whose center angle is 150to make the seat width match the standard. Then perform seat correction as described in 2), and then carry out lapping [A] and [B].
Grinding wheel angle 1 40 150 2
80
4.2.7 Valve guide replacement

1) Use a valve guide extraction tool(12.1-1 in Chapter 12) and extract the valve guide from the cylinder head. 2) Put liquid nitrogen or ether (or alcohol) with dry ice added in a container and put the valve guide for replacement in it for cooling. Then insert it in with a valve guide inserting tool (Refer to No.2 of 4.1.2 in Chapter 4). Do not touch the cooled valve guide with bare hands to avoid skin damage. 3) Check the inside diameter and finish to the standard inside diameter as required with a reamer. 4) Check the projection from the cylinder head.
Model 3TNV82A 4TNV84 3TNV84(T) 4TNV88 4TNV84T 4TNV94L 4TNV98(T) 4TNE106(T) 4 valves 2 valves Number of valves mm Projection 11.7 12.0 14.7 15.0 8.2 8.5 9.7 10. 13.4 13.6
81
4.2.8 Valve stem seal replacement

Always use a new seal after the intake/exhaust valve is disassembled. Since the one for the exhaust valve is marked with yellow paint, do not confuse the intake and exhaust valves. 1) Apply engine oil to the lip. 2) Push with the inserting tool (Refer to No.5 of 4.1.2 in Chapter 4) for installation.
3) Measure and check the projection of valve stem seal to keep proper clearance between valve guide and stem seal.
Model 3TNV82A 4TNV84 3TNV84(T) 4TNV88 4TNV84T 4TNV94L 4TNV98(T) 4TNE106(T) 4 valves 2 valves Number of valves mm Projection 15.7 16.0 18.7 19.0 9.9 10.2 11.7 12.0 15.4 15.6
82
4.3 Gear Train and Camshaft

4.3.1 Components

Disassemble in the order of the numbers in the illustration. 1) Perform steps 1) to 12) of the cylinder head disassembly procedure. 2) Remove the cooling water pump. 3) Remove the crankshaft pulley. (See Point 1 of 4.3.4) 4) Remove the gear case cover. (See Point 2 of 4.3.4) 5) Remove the fuel injection pump. (See Point 3 of 4.3.4) 6) Remove the idle gear assy. (See Point 4 of 4.3.4) 7) Remove the PTO drive gear. (See Point 5 of 4.3.4) 8) Remove the starting motor. 9) Remove the flywheel. (See Point 6 of 4.3.4) 10) Remove the camshaft assy. (See Point 7 of 4.3.4) 11) Remove the gear case. (See Point 8 of 4.3.4) 12) Remove the oil seal from the gear case cover. (See 4.3.6)

Reverse of the disassembly procedure.
83

Point1 [Disassemble] Remove the crankshaft pulley using a gear puller after removing the crankshaft pulley set bolt. When removing the pulley using the gear puller, use a pad and carefully operate so as not to damage the thread. Set the gear puller securely to prevent the pulley from being damaged. [Reassemble] Apply lithium grease to the oil seal lips. For the oil seal with double lips dust seal, further slightly apply engine oil on the lips so as not to damage them. Clean by wiping off any oil on both taper surfaces using detergent. Be sure to use the crankshaft pulley installing tool so as not to damage the oil seal lips. (See 4.3(6) Oil seal replacement) When installing the crankshaft pulley, apply lube oil to the set bolt to tighten and carefully assemble so as not to damage the oil seal.
Model 3TNV82A TNV88 4TNV94L/98/106(T) N m(kgf-m) Tightening torque 112.7 122.7 (11.5 12.5) 107.9 127.5 (11.0 13.0)
Point2 [Reassemble] When installing the gear case, do not forget to install the two reinforcing bolts at the center. Measure the backlash of each gear. mm Standard Limit 3TNV82A 88 Crankshaft gear, Camshaft gear, 0.07 0.15 0.17 Fuel injection pump gear, Idle gear, PTO gear,
Lubricating oil pump gear 4TNV94L-106(T) Crankshaft gear, Camshaft gear, Fuel injection pump gear, Idle gear, PTO gear, Balancer gear (only 4TNV106(T) ) Lubricating oil pump gear 0.11 0.19 Standard 0.08 0.14 0.12 0.18 0.09 0.15 0.21 Limit 0.16 0.20 0.17
Apply sealant and install the gear case by correctly positioning the two dowel pins.
84
Point3: (Refer to 7.2.5 in chapter 7) [Disassemble] Remove the mounting nut of the fuel injection pump drive gear, remove the gear using the gear puller, and remove the fuel injection pump. Do not forget to remove the stay on the rear side. When extracting the gear using the gear puller, use a pad at the shaft and carefully operate so as not to damage the thread. [Reassemble] Tightening torque for fuel pump drive gear nut (without lube. Oil)
Model TNV82A 88 4TNV94L/98/106(T) N m(kgf-m) Tightening torque 78 88 (8.0 9.0) 113 123 (11.5 12.5)
Point4 [Reassemble] Assemble crankshaft gear A, fuel injection pump drive gear B and camshaft gear C at the same time by aligning with idle gear A, B and C marks. Install the idle gear shaft with the oil hole facing upward. Point5 [Reassemble] Install the PTO drive gear with its inner spline side facing the flywheel. Point6 [Disassemble] Install a bolt as a handle in the hole at the end face of the flywheel and remove carefully so as not to damage the ring gear. [Reassemble] Flywheel mounting bolt : apply lube oil
Model 3TNV82A 88 4TNV94L/98/106(T) N m(kgf-m) Tightening torque 83.3 88.2 (8.5 9.0) 186.2 205.8 (19.0 21.0)
Point7 [Disassemble] Measure the camshaft side gap.

mm Item Side gap Standard 0.05 0.20 Limit 0.30
If the measured side gap exceeds the limit, replace the thrust metal.
85
[Disassemble] Since the camshaft gear is shrink-fit, heat it to 200 for extraction. 180 For camshaft removal, raise the engine with its mounting flange at the bottom. After removing the thrust metal mounting bolt from the camshaft gear hole, extract the camshaft carefully so as not to damage the bearing bushing. Rotate the camshaft a few turns before extracting it to prevent the tappet from being caught by the cam. After removing the camshaft, set the engine horizontal and fix it on the base. Unforeseen injury may arise due to falling of slipping when raising the engine vertically or returning it to the horizontal position. Proceed carefully so as not to lose balance. Point8: Gear case [Reassemble] Do not forget to install the oil pan mounting bolts on the bottom side when installing the gear case. Apply sealant (code No.977770-01212) and install the gear case by matching the two dowel pints.
86
4.3.5 Parts inspection and measurement

(1) Camshaft
Mainly check the contact between the tappet and cam contact surface, bearing seizure and wear, and gear damage. (a) Shaft bend measurement Support the camshaft with V blocks. Rotate the camshaft and measure the runout at the center of the camshaft and at each journal with a dial gage. half of the runout is the bend.
mm Item Bend Standard 0 0.02 Limit 0.05
(b) Intake/exhaust cam height measurement

mm Model 3TNV82A 88 4TNV94L98 4TNV106(T) Standard 38.600 38.800 43.400 43.600 50.900 51.100 Limit 38.350 43.150 50.650
(c) Camshaft outside diameter and bearing hole diameter measurement Measure the camshaft outside diameter with a micrometer. The oil clearance shall be calculated by subtracting the measured camshaft outside diameter from the the camshaft bushing inside diameter after insertion to the cylinder measured with a cylinder gage.
87
mm Model Place Gear side Item Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Bushing I.D. Camshaft O.D. Oil clearance Standard 44.990 45.055 44.925 44.950 0.040 0.130 45.000 45.025 44.910 44.935 0.065 0.115 45.000 45.025 44.925 44.950 0.050 0.100 49.990 50.055 49.925 49.950 0.040 0.130 50.000 50.025 49.910 49.935 0.065 0.115 50.000 50.025 49.925 49.950 0.05 0.100 57.980 58.050 57.910 57.940 0.040 0.140 58.000 58.030 57.895 57.925 0.075 0.135 58.000 58.030 57.910 57.940 0.050 0.120 Limit 45.130 44.890 0.240 45.100 44.875 0.225 45.100 44.890 0.210 50.130 49.890 0.240 50.100 49.875 0.225 50.100 49.890 0.210 58.105 57.875 0.250 58.105 57.860 0.245 58.105 57.875 0.230
3TNV82A TNV88
Intermediate position
Wheel side
Gear side
TNV94L/98(T)
Wheel side
Gear side
4TNV106(T)
Wheel side
(2) Idle gear

Mainly check the bushing seizure and wear, and gear damage. Shaft outside diameter and bushing inside diameter measurement
Item Shaft outside diameter Bushing inside diameter Clearance Standard 45.950 49.975 46.000 46.025 0.025 0.075 mm Limit 45.900 46.075 0.175
(3) PTO drive gear

Mainly check sticking of bearings on both sides, gear damage and looseness, and gear shaft damage and wear.
88
4.3.6 Oil seal replacement (Gear case side)

1) Replace the oil seal with a new one when the gear case is disassembled.
Extract the used oil seal.
2) Insert a new oil seal. Fit the position of the oil seal insertion to the end face of the gear case. (Refer to the below figure.) 3) Apply lithium grease to the oil seal tips. For the oil seal with double lips dust seal, further,
slightly apply engine oil on the oil seal lip so as not to damage them, when installing the pulley.
[NOTICE] Pay attention not to drop any oil on the taper surface of the crankshaft. If dropped, clean by wiping off using detergent. 4) Carefully install the crankshaft pulley so as not to damage the oil seal lips. Especially for the engine installed the oil seal with double lips dust seal, be sure to use the crankshaft pulley-installing tool.
4.3.7 Camshaft bushing replacement

Replace the bushing using the special service tool (Refer to No.7 of 4.1.2 in Chapter 4).
89
4.4 Cylinder Block

4.4.1 Components

Disassemble in the order of the numbers in the illustration. 1) Perform steps 1) to 12) in the cylinder head disassembly procedure. 2) Perform steps 1) to 12) in the gear train disassembly procedure. 3) Remove the oil pan. (See Point 1 of 4.4.4) 4) Remove the lubricating oil suction pipe. 5) Remove the piston w/rod. (See Point 2 of 4.4.4) 6) Remove the mounting flange. (See Point 3 of 4.4.4) 7) Remove the bearing metal caps. (See Point 4 of 4.4.4) 8) Remove the crankshaft. (See Point 5 of 4.4.4) 9) Remove the tappets. 10) Remove the pistons and rings. (See Point 6 of 4.4.4) 11) Remove the oil seal from the mounting flange. (See 4.4.8 of 4.4.4)

Reverse of the disassembly procedure.
90

Point1: Oil pan [Disassemble] Sealant is applied to the oil pan mounting surface on the block. Carefully operate soas not to damage or distort the bonding surface. [Reassemble] Apply sealant (code No.977770-01212) before reassembly. Point2: Piston w/rod [Disassemble] Measure the connecting rod side gap.
mm Standard 0.20 0.40
Carefully remove the carbon deposit on top of the cylinder so as not to damage the inner side of the cylinder. Set the piston at the BDC position and remove the connecting rod cap. Then set the piston at the TDC position, and push the connecting rod big end with the wooden shaft of a hammer. Proceed carefully so as not to cause the cylinder block catch the rod big end. Set the rod caps and crankpin metals in their correct combinations. [Reassemble] Apply oil especially carefully to the sliding contact surfaces of the pistons, rods and rings. Use the piston insertion tool (see 12.1-9 in Chapter 12) to insert each piston w/rod in the cylinder block and install the bearing metal cap.
Rod bolt tightening torque N m(kgf-m) Model Standard (apply lube oil) 3TNV82A TNV84 88 4TNV94L98 4TNV106(T) 37.2 41.2 (3.8 4.2) 44.1 49.0 (4.5 5.0) 53.9 58.8 (5.5 6.0) 78.5 83.4 (8.0 8.5)
Point3: mounting flange [Disassemble] Place the engine on a stable base with the cylinder block upper surface facing down, and remove the mounting flange carefully so as not to damage the combustion surface.
91
[Reassemble] Apply sealant (code No.977770-01212) and install the mounting flange by matching the two dowel pins. After assembly, raise the engine with its mounting flange on the bottom side. Unforeseen injury may arise due to falling of slipping when raising or reversing the engine. Carefully operate so as not to lose balance. Point4: Journal bearing cap [Disassemble] Before removing the journal bearing, measure the crankshaft side gap. Measure it in either method because there are the next two methods. 1) Install a dial gage on the cylinder block, and move a crankshaft in front and back, and measure the side gap as shown in the right figure.
2) Put a thickness gauge in the clearance between thrust metal and crankshaft directly, and measure it.
Side gap standard Model All models Standard 0.13 0.23 mm Limit 0.28
[Reassemble] If the side gap exceeds the standard, replace the thrust metal with an oversize one. Machine the standard width of the crankshaft thrust part into the dimension of the below table at the same time. Refer to a parts catalog when ordering the part. The surface finishing precision (refer to 4.4.5(2) in Chapter4):
0.25mm Oversized thrust metal (0.25DS) mm 0.25DS Thrust metal assy code Standard thickness 3TNV82A 119810-02940 2.055 2.105 TNV84 88 129150-02940 2.055 2.105 4TNV94L 98 129900-02940 2.055 2.105 4TNV106(T) 123900-02940 2.555 2.605 The standard width of the crankshaft thrust part mm Model Standard thickness 3TNV82A 25.250 25.271 TNV84 88 28.250 28.271 4TNV94L 98 32.250 32.275 4TNV106(T) 36.250 36.275
92
[Disassemble] Remove the bearing caps, cap side bearings, and thrust metals. Place each thrust metal with identification of the position and direction. The position number of reassembling is punched on a metal cap (except for both ends) and a cylinder block.
[Reassemble] Carefully install each thrust metal so that the grooved one is positioned away from the cap. Do not confuse the upper and lower main bearing metals. The upper main bearing metal (block side) has an oil hole, and the lower one does not. The arrow marks on the cap shall face the flywheel. Tighten main bearing cap bolts.
Main bearing cap bolt tightening torque (apply lube oil) Nm(kgfm) Model Standard 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) 76.4 80.4 (7.8 8.2) 93.2 98.1(9.5 10.5) 108.1 117.9 (11.0 12.0) 186.2 205.8 (19.0 21.0)
Point5: Crankshaft [Disassemble] Remove the crankshaft. Remove each main bearing metal upper (block side) and pair it with the metal cap side lower metal. Carefully prevent damage to the bearing or finger injury when removing the crankshaft because it is heavy.
93
Point6: Piston pin and rings [Disassemble] Using the piston ring replacer (see 4.1.2 in Chapter 4), remove the piston rings. Remove the circlip and remove the piston pin by pushing it out. [Reassemble] Install each piston ring on the piston, with the punched manufacturers mark facing upward. [Reassemble] The piston ring joints shall be staggered at by 120 intervals. Do not position the top ring joint vertical to the piston pin. The coil expander joint shall be opposite to the oil ring joint.
[Reassemble] When installing the piston pin to the rod and piston, the punched match mark on the big end of the connecting rod shall be opposite to the size mark on the piston top. [Reassemble] Install the piston in the cylinder clock with the punched mark on the big end of the rod on the nozzle side. (The embossed mark at the connecting rod I-beam section shall be on the flywheel side.)
94
4.4.5 Parts inspection and measurement

(1) Cylinder block
Especially clean head surface, cylinder bores and oil holes, and check after removing any carbon deposit and bonding agent. (a) Appearance inspection Check if there is any discoloration or crack. If crack is suspected, perform color check. Sufficiently clean the oil holes and check they are not clogged. (b) Cylinder bore and distortion Measure at 20 mm below the crest of the liner, at 20 mm from the bottom end and at the center. Roundness: Roundness is found as follows though it is the simple method. Measure cylinder diameters of the A direction and the B direction on each section of a, b and c. Roundness is the maximum value among those difference values. Cylindricity: Cylindricity is found as follows though it is the simple method. Measure cylinder diameters of a, b and c sections in the A direction, and calculate the difference in maximum value and minimum value of the measured diameters. In the same way measure and calculate the difference in the B direction. Cylindricity is the maximum value between those difference values.
mm Item Model 3TNV82A TNV84 Cylinder inside diameter TNV88 4TNV94L 4TNV98 4TNV106(T) Cylinder bore Roundness Cylindricity all TNV Standard 82.000 82.030 84.000 84.030 88.000 88.030 94.000 94.030 98.000 98.030 106.000 106.030 0.01 or less Limit 82.200 84.200 88.200 94.130 98.130 106.130 0.03
95
(c) If the limit is exceeded or any surface defect is found, repair by boring and honing. Use an oversized piston (and new piston rings) as required.
Oversized piston (0.25 mm, with piston rings) Model Code No. Standard (mm) 3TNV82A 3TNV84(T) 4TNV84 4TNV84T 3/4TNV88 4TNV94L 4TNV98 4TNV106 4TNV106T 719802-22900 129004-22900 129508-22900 129005-22900 729906-22900 129902-22700 729907-22900 723907-22910 82.250 84.250 84.250 88.250 94.250 98.250 106.250 106.250
Piston ring assy for oversized (0.25mm) Model Piston ring code No. 3TNV82A 3TNV84(T) 4TNV84 4TNV84T 3/4TNV88 4TNV94L 4TNV98 4TNV106(T) 719802-22950 129004-22950 129004-22950 129005-22950 729906-22950 729907-22950 723907-22950 Honing angle (deg.) Surface roughness Roundness/Cylindricity (mm)
Cylinder dimension after boring and honing Cylinder dimension Model (mm) 3TNV82A 3TNV84(T) 4TNV84 3/4TNV88 4TNV94L 4TNV98 4TNV106(T) 82.250 82.280 84.250 84.280 88.250 88.280 94.250 94.280 98.250 98.280 106.250 106.280
30 40 deg.
Rmax 1.0 3.5S
0.01 or less
96
(2) Crankshaft
Mainly check seizure and wear of the crankpins and journals. Since the crankshaft gear is shrink-fitted, heat to 180 to 200 when extraction is necessary. (a) Shaft portion color check After washing the crankshaft, inspect it by means of color check or a magnaflux inspector. Replace it if cracked or heavily damaged. Slight defects shall be corrected by grinding.
(b) Crankshaft bend Support the crankshaft journals at both ends with V-blocks. Use a dial gage and measure the runout at the center journal while rotating the shaft to inspect the bend.
Limit 0.02mm or less
(c) Crankpin and journal measurement Measure the outside diameter, roundness and taper at each crankpin and journal. Correct by grinding if unevenly wear, roundness exceeding the limit or insufficient outside diameter is found. Replace if the defect is excessive.
97
Crankpin Model & Item Pin outside diameter 3TNV82A Metal thickness Oil clearance Pin outside diameter TNV84 88 Metal thickness Oil clearance Pin outside diameter 4TNV94L 98 Metal thickness Oil clearance Pin outside diameter 4TNV106(T) Metal thickness Oil clearance Undersized crankpin bearing (0.25 mm) Model Code No. 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) 119810-23610 129150-23610 129900-23610 123900-23610 Standard 42.952 42.962 1.487 1.500 0.038 0.090 47.952 47.962 1.492 1.500 0.038 0.074 57.952 57.962 1.492 1.500 0.038 0.074 63.952 63.962 1.984 1.992 0.054 0.090 Limit
mm 42.902 0.150 47.902 0.150 57.902 0.150 63.902 0.150
If the oil clearance exceeds the limit, use an undersized bearing. Standard thickness (mm) 1.612 1.625 1.617 1.625 1.617 1.625 2.109 2.117
Pin machining dimension Model Pin machining dimension (mm) 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) 42.702 42.712 47.702 47.712 57.702 57.712 63.702 63.712
98
Crank journal Model 3TNV82A
Item Journal O.D. Metal thickness Oil clearance Journal O.D.
Standard 46.952 46.962 1.987 2.000 0.038 0.080 53.952 53.962 1.995 1.990 0.038 0.068 64.952 64.962 1.995 2.010 0.038 0.068 75.952 75.962 2.488 2.503 0.052 0.082
mm Limit 46.902 0.150 53.902 0.150 64.902 0.150 75.902 0.150
TNV84 88 (Selective assembly)
Metal thickness Oil clearance Journal O.D.
4TNV94 98 (Selective assembly)
Metal thickness Oil clearance Journal O.D.
4TNV106(T) (Selective assembly)
Metal thickness Oil clearance
If the clearance limit is exceeded, use an undersized bearing.

Undersized bearing (0.25mm) Model 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) Code No. 119810-02870 129150-02870 129900-02340 12900-02340 Standard thickness (mm) 2.112 2.125 2.112 2.125 2.112 2.125 2.605 2.618
Crankshaft Journal machining dimension Model 3TNV82A TNV84 88 4TNV94/98 4TNV106(T) Journal machining dimension (mm) 46.702 46.712 53.702 53.712 64.702 64.712 75.702 75.712
99
Dimension R and finishing precision of crankshaft journal and pin As for grinding processing of journal and pin, machine it by using the grinding wheel of the dimension R of below table. Surface finishing precision standard on journal and pin: Ry=0.8S super polishing Surface finishing precision standard on the thrust side of crankshaft arm:
Model 3TNV82A TNV84 88 4TNV94L/98(T) 4TNV106(T)
mm Finishing precision standard of dimension R 3.5 +0.3/ 0 4.0 +0.3/ 0
[NOTICE] 1) lf the oil clearance is excessive though the thicknesses of the iournal and crankpin metals are normal or if partial uneven wear is observed, re-grind the crankshaft and use an oversized metals.
2) lf rust or surface roughening exists on the rear side of the metals, coat it with blue or minimum.
Then assemble the crankpin metal to the connecting rod, and tighten the rod bolt to the specified torque to check the metal for contact. lf the contact surface occupies 75% or more, the metal
is normal. lf the contact surface is insufficient, the metal interference is insufficient. Replace the metal with a new one. (1) Thrust metal inspection
(a) Inspect any damage or wear. (b) Measure side gap and thrust metal thickness
Side gap and thrust metal thickness Side gap Model Standard TNV82A 88 4TNV94L 98 4TNV106(T) 0.14 0.22 0.13 0.23 0.13 0.23 mm Thrust metal thickness Standard Limit 1.930 1.980 1.930 1.980 2.430 2.480 1.850 1.850 2.35
Limit -
If the side gap is exceeded, use an oversized thrust metal.

Oversized metal (0.25mm) 3TNV82A TNV84 88 4TNV94L 98 4TNV106(T) Code No. Upper Lower ???119810-02940 (Up-down combination) 129150-02940 (Up-down combination) 129900-02370 123900-02370 129900-02360 123900-02360 Standard thickness (mm) 2.15 2.15 2.055 2.105 2.555 2.605
100
(4) Piston
Especially clean the combustion surface, circumference, ring grooves and piston pin bosses, and check after removing any carbon deposit. Any burr at a ring groove or snap ring groove shall be removed. If crack is suspected, inspect by color check. (a) Piston outside diameter measurement Measure the long diameter at H mm from the bottom end of the piston of the oval hole in the vertical direction to the piston pin hole.
Piston outside diameter Outside diameter Model Standard 3TNV82A 81.950 81.980 3,4TNV84(T) 83.945 83.975 3,4TNV88 87.945 87.975 4TNV94L 93.945 93.955 4TNV98(T) 97.940 97.950 4TNV106(T) 105.930 105.960
Limit 81.905 83.900 87.900 93.900 97.895 105.880
Clearance between piston and cylinder 0.035 0.065 0.040 0.070
mm Measurement position (H) 22 25 22 22 30
0.050 0.080
If the clearance between piston and cylinder exceeds the limit, use an oversized piston. (Refer to the tables of oversized pistons, oversized piston rings and cylinder boring dimension on 4.4.5(1)(c) in chapter 4.)
(b) Piston pin hole measurement Measure the outside diameter of piston pin and the inside diameter of piston pin hole. Calculate the clearance between piston pin and piston pin hole. If any data exceeds the limit, replace the part with a new one.
Model 3TNV82A Item Pin I.D. Pin O.D. Clearance Pin I.D. Pin O.D. Clearance Pin I.D. Pin O.D. Clearance Pin I.D. Pin O.D. Clearance Standard 23.000 23.009 22.995 23.000 0.000 0.014 26.000 26.009 25.995 26.000 0.000 0.014 30.000 30.009 29.989 30.000 0.000 0.020 37.000 37.011 36.989 37.000 0.000 0.022 mm Limit 23.039 22.965 0.074 26.039 25.965 0.074 30.039 29.959 0.080 37.039 36.959 0.080
TNV84 88
4TNV94L 4TNV98(T)
4TNV106(T)
101
(c) Piston ring, ring groove and end clearance measurement Except for the top ring, to measure the piston ring groove width, first measure the width of the piston ring. Then insert the piston ring into the ring. Then insert the piston ring into the ring groove. Insert a thickness gage in between the piston ring and groove to measure the gap between them. Obtain the ring groove width by adding ring width to the measured side clearance. To measure the end clearance, push the piston ring into the sleeve using the piston head, insert a thickness gage in end clearance to measure. The ring shall be pushed in to approx. 30 mm above the bottom end of the cylinder. For the top ring, measure only the piston ring joint end clearance in normal state.
102
Piston ring dimension Model Part Top ring
mm Item Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Standard 2.065 2.080 1.970 1.990 0.075 0.110 0.200 0.400 2.035 2.050 1.970 1.990 0.045 0.080 0.200 0.400 4.015 4.030 3.970 3.990 0.025 0.060 0.200 0.400 2.060 2.075 1.970 1.990 0.070 0.105 0.200 0.400 2.025 2.040 1.970 1.990 0.035 0.070 0.200 0.400 4.015 4.030 3.970 3.990 0.025 0.060 0.200 0.400 2.040 2.060 1.940 1.960 0.080 0.120 0.250 0.450 2.080 2.095 1.970 1.990 0.090 0.125 0.450 0.650 3.015 3.030 2.970 2.990 0.025 0.060 0.250 0.450 2.520 2.540 2.440 2.460 0.060 0.100 0.300 0.450 2.070 2.085 1.970 1.990 0.080 0.115 0.450 0.600 3.015 3.030 2.970 2.990 0.025 0.060 0.300 0.500 Limit 1.950 0.490 2.150 1.950 0.200 0.490 4.130 3.950 0.180 0.490 1.950 0.490 2.140 1.950 0.190 0.490 4.130 3.950 0.180 0.490 1.920 0.540 2.195 1.950 0.245 0.730 3.130 2.950 0.180 0.550 2.420 0.540 2.185 1.950 0.235 0.680 3.130 2.950 0.180 0.600
TNV82A/84
Second ring
Oil ring
Top ring
TNV88
Second ring
Oil ring
Top ring
4TNV94L 98
Second ring
Oil ring
Top ring
4TNV106(T)
Second ring
Oil ring
103
(5) Connecting rod

(a) Appearance inspection Inspect the portion near the boundary of the chamfered portion and I-beam section of the big and small ends of the connecting rod as well as the portion near the oil hole of the bushing at the small end for cracks, deformation, and discoloration. (b) Twist and parallelism measurement Use a connecting rod aligner and measure the twist and bend.
Item Twist and parallelism Standard dimension 0.03 or less per 100mm mm Limit dimension 0.08
(c) Rod small end measurement Measure the pin outside diameter according to 4.4.5.(4)(a) described above.
Model 3TNV82A Item Piston pin I.D. bushing Pin O.D. Clearance Piston pin I.D. bushing Pin O.D. Clearance Piston pin I.D. bushing Pin O.D. Clearance Piston pin I.D. bushing Pin O.D. Clearance Standard 23.025 23.038 22.995 23.000 0.025 0.043 26.025 26.038 25.995 26.000 0.025 0.043 30.025 30.038 29.987 30.000 0.025 0.051 37.025 37.038 36.989 37.000 0.025 0.049 mm Limit 23.068 22.967 0.101 26.068 25.967 0.101 30.068 29.959 0.109 37.068 36.961 0.107
TNV84 88
4TNV94L 98
4TNV106(T)
If the bushing is to be replaced because the oil clearance exceeds the limit, use spare part.
Model 3TNV82A TNV84 88 4TNV94L 98(T) 4TNV106(T) Service part code 119810-23910 129100-23910 129900-23910 123900-23910
104
(d) Rod big end measurement Measure the crankpin and bushing according to 4.4.5.(2)(c) described above. Calculate the oil clearance of a crank pin metal and a crank pin from the measured values of the crank pin metal inner diameter and the crank pin outside diameter. Replace a crank pin metal if the oil clearance becomes about the limit dimension of the below table. Correct by grinding if unevenly wear, roundness exceeding the limit or insufficient outside diameter is found. Also use an undersized metal. (Refer to the above (2) c.)
[NOTICE] When measuring the inside diameter of the rod big end, install the crankpin metals in the rod big end not to mistake the top and bottom of the metals and tighten the rod bolts by the standard torque.
Tightening torque of rod bolt Tightening torque Lubricating oil application Model Nm(kgf-m) (threaded portion, and bearing seat surface) 37.2 41.2 3TNV82A (3.8 4.2) 44.1 49.0 TNV84/88 (4.5 5.0) Lube. oil applied 53.9 58.8 4TNV94L/98 (5.5 6.0) 78.5 83.4 4TNV106(T) (8..0 8.5) Standard of rod big end Model Item Rod I.D. bushing 3TNV82A Crankpin O.D. Metal thickness Clearance Rod I.D. bushing TNV84/88 Crankpin O.D. Metal thickness Clearance Rod I.D. bushing 4TNV94L/98 Crankpin O.D. Metal thickness Clearance Rod I.D. bushing 4TNV106(T) Crankpin O.D. Metal thickness Clearance mm Standard 42.952 42.962 43.000 43.042 1.487 1.500 0.038 0.090 47.952 47.962 48.000 48.026 1.492 1.500 0.038 0.074 57.952 57.962 58.000 58.026 1.492 1.500 0.038 0.074 63.952 63.962 64.016 64.042 1.984 1.992 0.054 0.090 Limit 42.902 0.150 47.902 0.150 57.902 0.150 63.902 0.150
105
(6) Tappet
Mainly check the tappet contact surface with the cam and push rod. Slight surface defects shall be corrected with an oilstone. (a) Tappet stem outside diameter measurement
Model Item Tappet hole I.D. Stem O.D. Clearance Tappet hole I.D. 4TNV94L 98 Stem O.D. Clearance Tappet hole I.D. 4TNV106(T) Stem O.D. Clearance Standard 12.000 12.025 11.975 11.990 0.010 0.050 12.000 12.018 11.975 11.990 0.010 0.043 14.000 14.018 13.966 13.984 0.015 0.052 mm Limit 12.045 11.955 0.090 12.038 11.955 0.083 14.038 13.946 0.092
TNV82A 88
4.4.6 Cylinder bore correction

1) Slight uneven worn, flawed, etc. shall be corrected by honing only. If the cylinder is unevenly worn partially, flawed or otherwise damaged and cannot be repaired simply by honing, rebore the cylinder first and then hone. See 4.4.5.(1)(c) for the boring dimension. 2) Items to be prepared for honing Flex-Hone (see No.8 of 4.1.2 in Chapter 4) Electric drill Honing fluid (50:50 mixture of lube oil and diesel oil)
106
3) Apply the honing fluid to the Flex-Hone and turn the electric drill at 300 to 1200 rpm. Then insert the Flex-Hone into the cylinder bore while turning it, and move it up and down for about 30 sec. to obtain a honing mark with a cross hatch angle of 30 to 40 . [NOTICE] 1) Avoid faster revolution than 1200 rpm since it may cause breakdown. 2) Do not insert or extract the Flex-Hone in stopped state because the cylinder will be damaged.
4.4.7 Piston pin bushing replacement

Replace bushing by using the special service tool (see 4.1.2 No.3 in Chapter 4).
4.4.8 Oil seal replacement (Flywheel housing side)

1) Replace oil seal, when a flywheel housing is removed. 2) Insert a new oil seal with the oil seal insertion tool. 3) Apply lithium grease. Extract the used oil seal.
107
5. Lubrication System
5. LUBRICATION SYSTEM
5.1 Lubrication System Diagram
Note: It varies in the specifications of each model whether Oil cooler and Piston cooling of the * mark are attached.
108
5.2 Trochoid Pump Components

Trochoid pump (3TNV82A TNV88) Trochoid pump (4TNV94L/98/106)
5.3 Disassembly(Reverse the procedure below for assembly)

1) Loosen the belt, and remove the radiator pulley, fan and V-belt. See 4.2.2. 2) in Chapter 4. 2) Remove the crankshaft pulley. See 4.3.2. 3) in Chapter 4. 3) Remove the gear case cover. See 4.3.2. 4) in Chapter 4. 4) Remove the lubricating oil pump assy from the gear case for 4TNV94/98/106. (5.4 Point 1) Remove the lube oil cover from gear case cover for 3TNV82A-88. (5.4 Point 1) 5) Remove the pressure regulating valve from the lubricating oil pump body. (5.4 Point 2)
5.4 Servicing Points

Point 1 [Disassemble] Check if the pump rotates smoothly and see that there is no play between the shaft and gear, and inner rotor. [Reassemble] [NOTICE] Always check if the pump rotates smoothly after installation on the gear case. Running the engine when the pump rotation is heavy may cause the pump to be burnt. 1) 3TNV82A-88 Apply lube oil to rotor (outer/inner) insertion part. Assemble the outer rotor so that the mark of the end face may become a cover side when inserting it in the gear case. Fasten a lube oil pump cover by the standard torque. Tightening torque: 6.9 1.5N m (0.7 0.15kgf m) When replacing the lube oil pump, replace the whole assy. 2) 4TNV94L/98/106 Apply lube oil to lube oil pump insertion part of gear case. Install the outer rotor in the gear case so that the punch mark on the end face is seen. When replacing the lube oil pump, replace the whole assy. Point 2 [Disassemble-Reassemble] Only wash the pressure regulating valve. operation is detected.
Disassembly is unnecessary unless any abnormality in
109
5.5 Parts Inspection and Measurement

5.5.1 Trochoid pump inspection and measurement
(1) Outside clearance and side clearance of outer rotor
Insert a gap gage between a outer rotor and a pump body, and measure the clearance.
Outside clearance Model 3TNV82A 88 4TNV94L/98 4TNV106(T) mm Standard 0.12 0.21 0.100 0.155 0.100 0.165 Limit 0.30 0.25 0.25
When measuring a side clearance, put a right-angle gage to the pump body, insert a gap gage and measure the clearance.
Side clearance Model 3TNV82A 88 4TNV94L/98 4TNV106(T) mm Standard 0.02 0.07 0.05 0.10 0.03 0.12 Limit 0.12 0.15 0.17
(2) Inner rotor and gear boss clearance (3TNV82A-4TNV88)

Standard dimension (mm) 53.05 53.15 53.45 53.55 49.45 49.75 49.95 50.05 Standard clearance (mm) 0.3 0.5 Standard clearance limit (mm) 0.6
Item
Part Gear boss diameter Rotor inner diameter Width across flat of gear boss Width across flat of rotor
Inside clearance of inner rotor Width across flat clearance of inner rotor
0.2 0.6
0.7
110
(3) Rotor shaft clearance (4TNV94L/98/106)

Measure the outside diameter of rotor shaft and the shaft hole diameter of gear case. Calculate the clearance from that difference.
Model 4TNV94L/ 98
Inspection item Gear case bearing I.D. Rotor shaft O.D. Rotor clearance Gear case bearing I.D.
Standard 12.980 13.020 12.955 12.970 0.035 0.065 13.000 13.020 12.955 12.965 0.035 0.065
Limit 13.05 12.945 0.105 13.05 12.945 0.105
4TNV106(T)
Rotor shaft O.D. Rotor clearance
111
6. Cooling System
6. COOLING SYSTEM
6.1 Cooling Water System
6.2 Cooling Water Pump Components
112
6. Cooling System
6.3 Disassembly (Reverse the procedure below for assembly)

1) Remove the alternator. See 4.2.2. 1) in Chapter 4. 2) Remove the fan, V-belt and pulley. See 4.2.2. 2) in Chapter 4. 3) Remove the cooling water pump. (Point 1, in below 6.4) 4) Remove the thermostat. (Point 2 in below 6.4)
6.4 Servicing Points

Point 1 Disassemble-Reassemble: Check to see that the cooling water pump bearing is free from abnormal noise, sticking or play and water leakage from the bearing. If replacement is necessary, replace the whole cooling water pump assy. [NOTICE] Replace the O-ring of the cooling water pump with new one when disassembling. And, be sure to use the special O-ring for each engine model, because the material is different, although the dimension is the same as a commercial part. (Refer to the right figure.) Point 2 Disassemble: Check the thermostat function. See 2.7 in Chapter 2 for the inspection method.
113
7. Fuel Injection Pump/Governor
7. FUEL INJECTION PUMP/GOVERNOR

Only the outline of the MP fuel pump is explained in this chapter. Refer to the MP pump service manual of the separate volume for the disassembly and assembly.
7.1 Introduction
It is described about the features of the fuel injection pump, YDP-MP, disassembly, assembly and adjustment procedure. Fuel injection pump is the most important equipment, which is enable to make the sensitive adjustment according to the variable load of the engine. Therefore all of the parts are required not only very precise machining but also finest, assembling with top level. The careful arrangement of keeping off the dust and the rust when disassemble, adjustment and reassemble of the fuel injection pump is made in the market. YDP-MP Pump is a distributor type pump which is unified of Mono-plunger, a distributing shaft, a hydraulic head which equipped the delivery valve for each cylinder, pump housing which has a cam shaft internally and governor. The fuel, which is pressurized by the up and down movement of the plunger driven by the cam-rotation, is supplied through the distributor shaft, which is rotating accordingly. There are a model YDP-MP2 and a model YDP-MP4, and plunger diameter and fuel cam speed are different.
7.2 Fuel Injection Pump

7.2.1 Fuel system diagram
114
7.2.2 External view and components

Disassembly from the engine body 1) Remove the cooling fan, pulley and V-belt. 2) Remove the fuel injection pipe, fuel oil piping, fuel return pipe and rear stay. See point 1 of 7.2.5. 3) Remove the fuel injection pump cover (the cover of the drive gear). 4) Make ID marks on the gearing part of the pump drive gear and the idle gear with paint and so on. See Point 2 of 7.2.5. 5) Loosen a fuel pump drive gear nut, and remove a pump drive gear from the fuel pump by using a gear puller. See Point 3 of 4.3.4. 6) Remove a drive gear nut carefully not to drop it to the inside of the gear case. 7) Record the installation angle of the fuel pump precisely by using a mark-off line and a sticker. See (4) of 2.2.7. 8) Remove the fuel injection pump. See Point 3 of 7.2.5.
115
7.2.4 Assembly procedure

Reverse the disassembly procedure and adjust the fuel injection timing finally. See (4) of 2.2.7.

Point 1 [Disassemble] Block an entrance with the tape so that trash may not enter the fuel injection pipe and the fuel injection pump. Point 2 [Disassemble] After putting the I.D. marks on the gearing part of the pump drive gear and the idle gear with paint and so on, remove the gear installation nut. [NOTICE] Don't remove four flange bolts.
[Reassemble] Reassemble the pump driving gear while checking the I.D. marks on the driving gear and idle gear.
Tightening torque of the gear installation nut Model TNV82A 88 4TNV94 106(T) N m(kgf m) 78 88 (8 9) 113 123 (11.5 12.5) Lubricating oil application (thread portion, and seat surface) Not applied
116
Point 3 [Disassemble] There is an acoustic material part to name as fuel pump spacer between the fuel pump and the cylinder block. Loosen fuel pump installation bolts with a closed wrench when disassembling a fuel pump. [NOTICE] An intake manifold may obstruct the disassembly of the fuel pump by the engine model. Remove the fuel pump after removing the intake manifold first.
[Reassemble] When installing a fuel pump on the gear case, put a fuel pump spacer between the cylinder blocks, and install it .
117
8. Turbochager
8. TURBOCHAGER: Disassembly, inspection and reassembly

8.1 Structure and Functions
8.1.1 Main specifications
Applicable engine model (application) Turbocharger model Turbocharger specification Turbine type Blower (compressor) type Lubrication method Maxcontinuous allowable speed 250,000 750 41(4.2) 46(4.7) 3TNV84T(CL, VM) 4TNV84T(CL) RHB31 3TNV84T(VM) RHB51 Standard (w/waste gate) Radial flow Centrifugal External lubrication 180,000 4TNV106T(CL, VM) RHF5
Maxcontinuous allowable gas inlet temperature Dry weight 24(2.4) N(kgf) Note) VM application is provided with the waste gate.
8.1.2 Construction
118
8. Turbochager
8.1.3 Structural and functional outline

No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Part name Turbine shaft OiN thrower Turbine side seal ring Seal plate Journal bearing Thrust bearing Compressor housing M5 hexagon bolt M5 spring washer Compressor side clamp Turbine housing M6 hexagon bolt Turbine side clamp Lock washer Bearing housing Retaining ring M3 countersunk flat head screw Compressor wheel Shaft end nut Heat protector
(1) Turbine
The exhaust gas from the engine is accelerated at the nozzle portion in the turbine housing and blown onto the turbine impeller to rotate the turbine shaft. This is called the turbine. A seal ring and heat insulating plate are installed to prevent the bearing from adverse influence of the gas.
(2) Compressor
The compressor impeller installed on the turbine shaft rotates with the shaft to suck and compress air for feeding into the intake manifold. This is called the blower or compressor.
(3) Bearings
Thrust bearing As the turbine shaft is constantly applied with a thrust force, this bearing prevents the shaft from being moved by the thrust force. Radial bearing A floating bearing is adopted. Since the bearing moves with the turbine shaft as the oil films are formed both inside and outside the bearing, the bearing sliding speed is slower than the turbine shaft speed, resulting in higher dynamic stability.
(4) Compressor side sealing mechanism

To prevent the intake air and oil form leaking, a seal ring and a seal plate are provided to form a double wall structure on the rear side of the compressor impeller.
(5) Waste gate

When the blower side pressure (intake air pressure) exceeds the specified level, the exhaust gas at the turbine inlet is partially bypassed to the exhaust discharge side to control the turbine rpm so as to maintain the intake pressure at the specified level for improving the response to load variation in the low to medium speed range and to minimize black smoke generation. It consists of a control assembly separated from the turbocharger and a valve assembly installed in the turbine impeller chamber.
119
8. Turbochager
8.1.4 Components
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Part name Turbine shaft Thrust bushing Oil thrower Seal ring Seal ring Seal ring (turbine side) Lock nut Impeller Seal plate Journal bearing Thrust bearing Compressor housing Flanged bolt Spring washer Clamp Turbine housing
No. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Part name Bolt Lock plate Bearing housing Retaining ring Screw Screw Lock washer Heat protector Liquid gasket Waste gate actuator Hose Adapter Clip Retaining ring Waste gate valve Link plate
120
8. Turbochager
8.2 Service Standards and Tightening Torque

8.2.1 Service standards
(1) RHF5 type

Standard dimension Turbine shaft journal outside diameter (A) Turbine shaft seal ring groove width (E) Turbine shaft Compressor side seal ring groove width (G1) Compressor side seal ring groove width (G2) Turbine shaft run-out Journal bearing inside diameter (C) Bearing Journal bearing outside diameter (D) Bearing housing inside diameter (B) Thrust bearing Seal ring fixing area Thrust bearing width (J) Thrust bushing groove dimension (K) Turbine side (bearing housing)(F) Compressor side (seal ring)(H1) Compressor side (seal ring)(H2) 7.99 8.00 1.25 1.28 1.22 1.23 1.02 1.03 0.002 8.01 8.03 12.32 12.33 12.40 12.41 3.99 4.01 4.04 4.05 15.00 15.02 12.40 12.42 10.00 10.02 0.03 0.06 0.08 0.13 Unit: mm Wear limit 7.98 1.29 1.31 1.11 0.011 8.04 12.31 12.42 3.98 4.07 15.05 12.45 10.05 0.09 0.17
Rotor play in axial direction Rotor play in radial direction
121
8. Turbochager
(2) RHB31/RHB51 type

Standard dimension RHB31 RHB51 6.257 6.263 7.99 8.00 1.038 1.062 1.02 1.03 0.82 0.83 0.002 6.275 6.285 9.940 9.946 9.995 10.005 3.59 3.61 3.632 3.642 11.00 11.018 9.987 10.025 7.968 8.00 0.022 0.053 0.061 0.093 1.25 1.28 1.22 1.23 1.02 1.03 0.002 8.01 8.03 12.32 12.33 12.40 12.41 3.99 4.01 4.04 4.05 15.00 15.02 12.40 12.42 10.00 10.02 0.03 0.06 0.08 0.13 Unit: mm Wear limit RHB31 RHB51 6.25 7.98 1.07 1.04 0.84 0.005 6.29 9.93 10.01 3.58 3.65 11.03 10.04 8.01 0.07 0.12 1.29 1.31 1.11 0.011 8.04 12.31 12.42 3.98 4.07 15.05 12.45 10.05 0.09 0.17
Turbine shaft journal outside diameter (A) Turbine shaft seal ring groove width (E) Turbine shaft Compressor side seal ring groove width (G1) Compressor side seal ring groove width (G2) Turbine shaft run-out Journal bearing inside diameter (C) Bearing Journal bearing outside diameter (D) Bearing housing inside diameter (B) Thrust bearing Seal ring fixing area Thrust bearing width (J) Thrust bushing groove dimension (K) Turbine side (bearing housing)(F) Compressor side (seal ring)(H1) Compressor side (seal ring)(H2)
Rotor play in axial direction Rotor play in radial direction
8.2.2 Tightening torque

(1) RHF5 type
Part Turbine housing set bolt Compressor housing set bolt Thrust bearing set screw Seal plate set screw Blower impeller set nut (left-handed screw) Thread diameter M8 M5 M3 M3 M5 N m(kgf cm) Tightening torque 27 29 (275 295) 4.2 5.2 (43 53) 1.2 1.4 (12 14) 1.2 1.4 (12 14) 1.8 2.2 (18 22)
(2) RHB31/ RHB51 type

Part Waste gate actuator set bolt Lock plate set bolt Thrust bearing set screw Seal plate set screw Blower impeller set nut (left-handed screw) Thread diameter M5 M6 M8 M3 M3 M5 N m(kgf cm) Tightening torque RHB31 RHB51 3.9 4.9 (40 50) 3.9 4.9 (40 50) 11.8 12.8 (120 130) 11.8 12.8 (120 130) 1.2 1.4 (12 14) 1.2 1.4 (12 14) 0.9 1.19 11 11.8 12.8 (120 130) 27.0 28.9 (275 295) 1.2 1.4 (12 14) 1.2 1.4 (12 14) 1.8 2.218 22
122
8. Turbochager
8.3 Periodic Inspection Procedure

8.3.1 Periodic inspection intervals
Periodically inspect the turbocharger for the overall conditions and fouling. The inspection interval varies with the operating conditions, but refer to the table below for the guideline for each application.
Application For vehicles (automobiles) For construction machinery For faming machinery For marine use Rotor rotation Rotor play Overhaul and overall inspection Oil filter cleaning and inspection Engine oil replacement Every 6 months or 60,000km Every 6 months or 500hrs Every 6 months or 200hrs Every 6 months or 1,500hrs Inspection interval Every 12 months or 150,000km Every 12 months or 1,000hrs Every 12 months or 400hrs Every 12 months or 3,000hrs Every 24 months or 300,000km Every 24 months or 2,000hrs Every 24 months or 800hrs Every 24 months or 6,000hrs
Based on engine operation manual
123
8. Turbochager
8.3.2 Inspection procedure

(1) Rotor rotation inspection
Inspect the rotor rotation by listening to any abnormal sound generation during rotation. For inspection with a sound detecting bar, bring the tip end of the bar into strong contact with the turbocharger case and raise the engine speed gradually. If any high pitch sound is generated at intervals of 2 to 3 seconds, the rotation is abnormal. Since the bearing or rotor may be defective in this state, either replace or overhaul the turbocharger.
(2) Rotor play inspection

Remove the turbocharger from the engine and inspect the rotor play in the axial and radial directions according to the procedure below. After removing the turbocharger from the engine, always bind the oil inlet and outlet holes with adhesive tape.
Rotor play in axial direction
124
8. Turbochager
8.3.3 Waste gate valve adjustment procedure

Rotor play in radial direction
It is indispensable to adjust the waste gate valve opening pressure and lift after its overhaul or inner parts replacement. Negligence of this adjustment will adversely affect the engine performance. [NOTICE] If the adjustment is impossible, give up overhaul but replace the whole turbocharger assembly.
(1) Method for checking the waste gate valve opening pressure and lift
(a) Equipment Prepare the equipment shown in the figure below.
125
8. Turbochager
(b) Measuring instruments and devices

Dial gage Manometer Pressure regulating valve Pressure reducing valve Pressure gage Capable of measuring 0 to 10 mm (A flat head type is recommendable.) Mercury column or electrical type (capable of measuring 0 to 1500 mmHg) Allowing gradual adjustment in a range between 0 and 2 kgf/cm2 (0.196 Mpa) Used for suppressing the air supply pressure at 5 kgf/cm2 (0.49 Mpa) or less. Bourdon tube pressure gage (0 to 10 kgf/cm2 (0.98 Mpa))
(c) Check method 1) Set the manometer control pressure (Pc) applied to the waste gate actuator to 0 and set the dial gage to the zero point. 2) Gradually open the pressure regulating valve and measure the Pc value when the actuator rod is operated by 2 mm. 3) For the hysteresis, let the rod move to 3 mm first. The gradually close the pressure regulating valve, measure the pressure when the rod is moved to 2mm and obtain the difference from the pressure measured in b. above. 4) Precautions Set the dial gage on the extension line of the actuator rod. The piping and joints shall completely be free from leak. Fix the turbocharger and dial gage securely. If an electric manometer is used, it shall have sufficient precision. Even when an electric manometer is used, use of a mercury column type manometer in combination is recommended for calibration and daily check. The speed for increasing/decreasing Pc by means of the pressure regulating valve shall be very slow near the measuring point. If the mm position is exceeded, restart from the beginning. Do not apply over 0.49 MPa (5 kgf/cm2) to the actuator.
(2) Waste gate actuator leak test
Apply 0.12 Mpa (1.2kgf/cm2) to the actuator and hold the state for minute. The actuator is good if the pressure then is 0.11 Mpa (1.1kgf/cm2) or above.
126
8. Turbochager
8.4 Disassembly Procedure

8.4.1 Preparation for disassembly
In addition to the general tools, the following special tools are required for turbocharger disassembly and reassembly:
Tool name Use For removing thrust bearing and thrust bushing Illustration
Bar Material: Copper or brass For removing floating bearing circlip Pliers
For removing seal ring Pliers
Torque driver for TORX bolt (multifunctional type) 0.5 to 4.9N-m (5 to 50 kgf-cm)
For thrust bearing installation (for M3):1.3 N-m (13 kgf-cm) For seal plate installation (for M3):1.3 N-m (13 kgf-cm)
Item sold on market
(Type: TORX TT20 or equivalent) For fixing turbine shaft (mm dodecagonal) Box wrench Box only may be used. For following bolts and nuts: M8:mm, kgf-cm(N-m) M5:mm, kgf-cm(N-m) M5:mm, kgf-cm(N-m) For measuring play in axial and radial directions: To be installed on a dial gage
Torque wrench (single purpose)
Probe
127
8. Turbochager
8.4.2 Inspection before disassembly

1) Inspect the turbine wheel and compressor impeller for any undesirable contact and the rotor for smooth rotation. 2) Measure the rotor play as described in section 8.3(2.2). Rotor axial play Wear limit: mm Rotor radial play Wear limit: mm
8.4.3 Disassembly
The mounting angles of the turbine housing, bearing housing and compressor housing are determined according to its mounting state on the engine. Put match marks before starting disassembly. Note: The number after each part is the one described in the structural drawing in 8.1(2).
(1) Compressor housing removal

1) Remove flanged hexagon bolt 8 and compressor side keep plate 10. 2) Remove compressor housing 7. Note: 1) Liquid gasket is applied on the surface of compressor housing 7 where bearing housing 15 is mounted. 2) When disassembling compressor housing 7, carefully operate so as not to damage the compressor impeller.
(2) Compressor impeller removal

1) Set a box spanner (10mm) on the turbine side end of the turbine shaft, and remove shaft end clamp 18. Note: Pay attention to the loosening direction since the shaft end nut has left-handed screw. 2) Remove compressor impeller 18.
(3) Turbine housing removal

1) Remove hexagon nut 12 and turbine side keep plate 13. 2) Remove turbine housing 11.
(4) Turbine shaft extraction

1) Hold heat insulating plate 20 lightly with a hand, and extract turbine shaft 1. Note: If the turbine shaft is hard to be extracted, tap the compressor side end of the shaft lightly with a wooden hammer. 2) Remove heat insulating plate 20.
(5) Seal plate removal

1) Use the Torx driver and loosen M3 Torx T-type machine screw 17 for seal plate mounting. 2) Remove seal plate 4. Note: Liquid gasket has been applied to the seal plate and bearing housing mounting surface. 3) Remove oil thrower 2 from the seal plate.
(6) Slide bearing and thrust bushing removal

1) Use the Torx driver and loosen the M3 Torx T-type machine screw for thrust bearing installation. 2) Use the bar (copper) and remove thrust bearing 6 and thrust bushing.
128
8. Turbochager
(7) Floating bearing removal

1) Use the stop ring pliers and remove circlip 16 from bearing housing 15. 2) Remove floating bearing 5 from bearing housing 15.
(8) Seal ring removal

1) Remove turbine side seal ring 3 from turbine shaft 1. 2) Remove compressor side seal ring (small) and compressor side seal ring (large) from oil thrower 2.
129
8. Turbochager
8.5 Washing and Inspection procedure

8.5.1 Washing
(1) Inspection before washing
Visually inspect each part before washing to check trace of seizure, wear, foreign matter or carbon adhesion. Carefully inspect for identifying the cause of trouble especially when a fault has occurred.
Major inspection items Check point Carbon adhesion state Checking position 1) Turbine shaft 1, turbine side seal ring and rear side of turbine wheel 2) Heat insulating plate 20 mounting portion and inside of bearing housing 15 1) Turbine shaft 1, journal portion and thrust bushing oil thrower 2 2) Floating bearing 5 and thrust bearing 6 3) Bearing housing 15 and inner wall of bearing fitting ring 1) Inner wall of turbine housing 11 2) Outer surface of bearing housing 11 and heat insulating plate 20 mounting portion 3) Turbine shaft 1 turbine side seal ring portion and rear side of turbine wheel 4) Inner wall of compressor housing 7 5) rear side of compressor impeller 18 6) Surface and seal ring inserting portion of seal plate 4
Lubrication status (wear, seizure, discoloration, etc.)
Oil leak state
(2) Washing procedure

Keep the following in mind when washing the parts.
Part a) Turbine s haft Procedure 1) Boil the turbine in the washing bucket. Do not strike the blade to remove the carbon. 2) Immerse in the detergent until the carbon and other deposits are softened. 3) Use a plastic scraper or hand hair scrubber to remove the softened deposits. Detergent 4) Protect the bearing surface and seal ring groove on Standard carbon the turbine shaft so as not to be damaged. removing agent 5) Any deposit remaining on the turbine shaft due to improper washing may cause unbalancing. Be sure to remove thoroughly. Never use a wire brush. Tools 1) Boil the turbine in the washing bucket. Same as for turbine shaft 2) Immerse in the detergent until the carbon and other deposits are softened. Detergent 3) Use a plastic scraper or hard hair scrubber to Same as for turbine shaft remove the softened deposits. Tools 1) Immerse in the washing bucket until the deposit is 1)Bucket(500 500) softened. 2)Brush 2) Use a plastic scraper or hard hair scrubber to remove the softened deposits. Detergent Never use a wire brush. 1) Wash all other parts with diesel oil. 2) Clean the lubricating oil path by blowing with compressed air. 3) Be especially careful so as not to damage or corrode the parts. Tools and detergent Tools 1) Bucket(500 500) 2) Heat source: Steam or gas burner 3) Brush
b) Turbine wheel chamber
c) Blower blade and chamber
d) Others
130
8. Turbochager
8.5.2 Inspection procedure

(1) Compressor housing 7
Inspect the compressor housing for any contact trace with the compressor impeller, surface defect, dent or crack at joint surface, and replace it if defective.
(2) Turbine housing 11

Inspect any trace of contact with the turbine wheel, exfoliation due to degradation by oxidation of the cast surface, thermal deformation or crack. Replace with a new one of defective.
(3) Compressor impeller 18

Inspect any contact trace, chipping, corrosion or deformation. Replace with a new one if defective.
(4) Turbine shaft 1

1) Inspect any contact trace, chipping, thermal discoloration or deformation at the turbine wheel. Check the shaft portion for bend, the journal portion for thermal discoloration or abnormal wear, and the seal ring groove for surface defect or wear. Replace with a new one if defective. 2) Measure the turbine shaft journal outside diameter (A) and seal ring groove width (E). Replace with a new turbine shaft if beyond the wear limit. Wear limit of journal outside diameter (A) 7.98mm RHF5 7.98mm RHB51 6.25mm RHB31 Wear limit of ring groove width (E) 1.29mm RHF5 1.29mm RHB51 1.07mm RHB31 3) Measure the turbine shaft run-out, and replace with a new turbine shaft if it exceeds 0.011 mm.
(5) Heat insulating plate 20

Inspect the heat insulating plate for any contact trace, thermal deformation or corrosion Replace with a new one if defective.
131
8. Turbochager
(6) Thrust bushing, oil thrower 2 and thrust bearing 6 Inspect each part for wear, surface defect and discoloration.
Replace with a new one if defective even within the wear limit. (a) Thrust bushing Measure the distance between grooves (K) of the thrust bushing, and replace with a new one if the wear limit is exceeded. Wear limit 4.07mm RHF5 4.07mm RHB51 3.65mm RHB31 (b) Oil thrower 2 Measure the seal ring groove widths (G1) and (G2), and replace with a new one if the wear limit is exceeded. Wear limits RHF5--- G1: 1.31mm, G2: 1.11mm RHB51--- G1: 1.31mm, G2: 1.11mm RHB31--- G1: 1.04mm, G2: 0.84mm (c) Thrust bearing 6 Measure the thrust bearing width (J), and replace with a new one if the wear limit is exceeded. Wear limit RHF5 RHB51 RHB31 3.98mm 3.98mm 3.58mm
(7) Floating bearing 5

1) Inspect the floating bearing for abnormal wear, discoloration or surface defect. Replace with a new one if defective. 2) Measure the inside diameter (C) and outside diameter(D). Replace the bearing if either wear limit is exceeded. Wear limits Outside diameter (D): 12.31mm, RHF5 Inside diameter (C): 8.04mm Outside diameter (D): 12.31mm, RHB51 Inside diameter (C): 8.04mm Outside diameter (D): 9.93mm, RHB31 Inside diameter (C): 6.29mm
132
8. Turbochager
(8) Bearing housing 15

1) Inspect the housing for cast surface exfoliation due to oxidation and degradation, dent or crack. 2) Inspect circlip 16 for chipping or crack, and replace with a new one if defective. 3) Measure the (B) and (F) portions of the bearing housing shown in the figure below. Replace with a new one if either wear limit is exceeded. Wear limit of bearing housing inside diameter (B) 12.42mm RHF5 12.42mm RHB51 10.01mm RHB31 Wear limit of turbine side seal ring inserting portion (F) 15.05mm RHF5 15.05mm RHB51 11.03mm RHB31
(9) Seal plate 4

1) Inspect the seal plate for any contact trace, joint surface defect, dent or crack. Replace it if defective. 2) Measure the seal ring inserting dimensions (H1 and H2) on the compressor side, and replace the seal ring with a new one if either wear limit is exceeded. Wear limits H1: 12.45mm, H2: 10.05mm RHF5 H1: 12.45mm, H2: 10.05mm RHB51 H1: 10.04mm, H2: 8.01mm RHB31
(10) Seal rings

Replace seal rings with new ones.
(11) Inspect keep plates 10, 13 and bolts for any deformation, and replace defective parts with new ones. Also replace M3 Torx machine screws with new ones.
133
8. Turbochager
8.6 Reassembly Procedure

8.6.1 Preparation for reassembly
1) Prepare general tools, special tools, liquid gasket (Three Bond No.1207) and Locktite No.242 before reassembling the turbocharger. 2) Always replace the following parts with new ones: Turbine side seal ring 1pc. Compressor side seal ring(large) 1pc. Compressor side seal ring(small) 1pc. M3 machine screws 3pcs. M3 machine screws 4pcs.
8.6.2 Reassembly
(1) Floating bearing installation
1) Use the snap ring pliers and install inner circlip 16 on bearing housing 15. 2) Install floating bearing 5 in bearing housing 15. 3) Use the snap ring pliers and install outer circlip 16 on bearing housing 15. Note: 1) The circlip joint shall be positioned as shown in the figure at right above. The rounded side of the circlip shall face the bearing. 2) Apply lubricating oil on the floating bearing before reassembly.
(2) Turbine shaft installation

1) Fit the seal ring onto turbine shaft 1. 2) Install heat insulating plate 20 on the turbine side of bearing housing 15. 3) Apply lubricating oil on the journal portion of the turbine shaft and insert the shaft from the turbine side of bearing housing 15. Note: Carefully operate so as not to damage the floating bearing by the turbine shaft. The seal ring joint shall be positioned on the lubricating oil inlet side after centering with the turbine shaft.
134
8. Turbochager
(3) Thrust bearing installation

1) Fit thrust bushing on turbine shaft 1. 2) Apply lubricating oil on the bearing portion of thrust bearing 6 and install it in bearing housing 15. 3) Apply Locktite on the threaded portion of M3 Torx T machine screw 17 for thrust bearing installation, and use Torx torque driver for installation by tightening to the specified torque. Tightening torque: 1.3 0.1N-m (13 1kgf-cm)
(4) Seal plate installation

1) Fit the seal ring on oil thrower 2. 2) Insert oil thrower 2 into seal plate 4. Note: The seal ring joint portion shall be positioned as illustrated at right. 3) Apply liquid gasket (Three Bond No.1207) on the seal plate mounting surface on the compressor side of bearing housing 15. Note: See the illustration below for the applying position. Applying thickness: 0.1 0.2 mm 4) Install seal plate 4 on bearing housing 15. 5) Apply Locktite on the threaded portion of M3 machine screw for seal plate mounting, and tighten it with a torque screwdriver. Tightening torque: 1.3 0.1N-m (13 1kgf-cm)
135
8. Turbochager
(5) Compressor impeller installation

1) Fit compressor impeller 18 onto turbine shaft 1. 2) Set a box spanner (10 mm) on the turbine side end of turbine shaft 1, and tighten shaft end nut 19. Note: Since the shaft end nut has left-handed screw, pay attention to the tightening direction. Tightening torque: 2.0 0.2N-m (20 2kgf-cm)
(6) Turbine housing installation

1) Install bearing housing 15 on turbine housing 11 by aligning the match marks put before disassembly. Note: In case of part replacement, check the oil inlet and outlet positions and the exhaust gas inlet position before reassembly. 2) Install the turbine side keep plate and tighten M8 hexagon bolt 12. Tightening torque: 285 10N-m (28 1kgf-cm)
(7) Compressor housing installation

1) Apply liquid gasket (Three Bond No.1207) on the compressor side flange of bearing housing 15. Note: See section (4)3) for the portion to be applied. Applying thickness: 0.1 0.2 mm 2) Check the mark and install the compressor housing 7 on the bearing housing 15. Note: When a part is replaced, confirm a position of an oil entrance and a position of an air exit, and assemble it. 3) Install the keep plate 10 on compressor side, and tighten M8 hexagon bolt 8. Tightening torque: 48 N-m (4.7 0.5kgf-cm)
(8) Rotor play measurement

See the inspection procedure in section 8.3.2 for the measurement method. If the rotor play does not satisfy the standard, reassembly is necessary since assembly error or use of a wrong part is conceivable. Service standard of rotor play in axial direction 0.03 0.06mm RHF5 0.03 0.06mm RHB51 0.022 0.053mm RHB31 Service standard of rotor play in radial direction 0.08 0.13mm RHF5 0.08 0.13mm RHB51 0.061 0.093mm RHB31
136
8. Turbochager
8.7 Handling after Disassembly and Reassembly

When installing the turbocharger on the engine or handling the turbocharger after installation, strictly observe the instructions given below. Especially pay careful attention for preventing foreign matter entrance into the turbocharger.
8.7.1 Instructions for turbocharger installation

Lubrication system 1) Pour new lubricating oil through the oil filler port before installation on the engine, and manually turn the turbine shaft to lubricate the floating and thrust bearings. 2) Flush the oil inlet pipe from the engine and outlet pipe, and check no crushed pipe nor dirt or foreign matter remaining in the pipes. 3) Connect the pipes securely so as to ensure no oil leak from joints. Intake system 1) Check no foreign matter or dirt in the intake line. 2) Connect securely to prevent any air leak from joints with the intake duct and air cleaner. Exhaust system 1) Check no dirt or foreign matter in the exhaust system. 2) Since heat resistant steel is used for the bolts and nuts, do not use general bolts and nuts for installation. Always apply anti-seizure agent on fastening bolts and nuts to be tightened. (Use heat-resistant hexagon bolts for the turbine housing.) 3) Connect exhaust pipes securely to prevent gas leak from each pipe joint.
137
8. Turbochager
8.8 Troubleshooting
Sufficient turbocharger performance and required engine output cannot be obtained if there is any fault. In such a case, first check each engine part to see there is no engine fault. Then inspect the turbocharger for troubleshooting according to the procedure shown below.
8.8.1 Excessively exhaust smoke

(1) Insufficient intake air volume
Cause 1) Clogged air cleaner element 2) Blocked air intake port 3) Leak from a joint in intake line Corrective action Replace or wash the element. Correct to the normal state. Inspect and repair.
(2) Turbocharger revolution failure

Cause 1) Deposit of impurities in oil sticking on the turbine side seal portion to make turbine revolution heavy 2) Sticking bearing Insufficient lubrication or clogged lubrication piping Excessively high oil temperature Unbalanced rotating part Insufficient warming up or sudden stoop from loaded operation (no-load operation) 3) Contact or breakdown of turbine wheel or blower vane Excessive revolution Excessive exhaust temperature rise Foreign matter invasion worn bearing Assembly defect Corrective action Turbocharger overhaul (disassembly and washing) with lubricating oil replacement Turbocharger overhaul (disassembly and repair) Lubricating oil line inspection, repair of defective portion and lubricating oil replacement Rotating part replacement or washing Strict observance of instructions in operation manual Inspection and repair of each engine part Perfect foreign matter elimination in disassembled state, followed by inspection and repair of individual air cleaner and engine components turbocharger overhaul (disassembly and repair) Reassembly
(3) Influence of exhaust resistance

Cause 1) Exhaust gas leak before the turbocharger to decrease its revolutions 2) Deformed or clogged exhaust pipe to decrease turbocharger revolutions Corrective action Joint inspection and correction Correct to the normal state.
8.8.2 White smoke generation

Cause 1) Clogged or deformed oil return pipe causing oil flow to the blower or turbine side 2) Excessive bearing wear causing abnormal wear or damage of seal ring Corrective action Repair or pipe replacement Turbocharger disassembly and repair
138
8. Turbochager
8.8.3 Sudden oil decrease

Cause 1) Excessive bearing wear causing abnormal wear or damage of seal ring Corrective action Turbocharger disassembly and repair
8.8.4 Decrease in output

Cause 1) Gas leak from any part in exhaust piping 2) Air leak from discharge side of blower 3) Clogged air cleaner element 4) Fouled or damaged turbocharger Element cleaning or replacement Turbocharger disassembly and repair or replacement Corrective action Inspection and repair of defective portion
8.8.5 Poor (slow) response (starting) of turbocharger

Cause 1) Hard carbon deposit on the turbine side (wheel sealing portion) to make turbine shaft revolution heavy 2) Incomplete combustion Corrective action Turbocharger disassembly and washing with lubricating oil replacement Engine combustion state inspection, followed by improvement of combustion to normal state
8.8.6 Abnormal sound or vibration

(1) Abnormal sound generation
Cause 1) Excessively narrowed gas path due to clogged nozzle in turbine wheel chamber or reverse flow of blower discharge in acceleration (generally called surging) 2) Contact rotating part Corrective action Turbocharger disassembly and washing
Turbocharger disassembly and repair or replacement
(2) Vibration
Cause 1) Loosened intake, exhaust or oil pipe connection with the turbocharger 2) Damaged bearing, contact between rotating part and adjacent part, or chipping of turbine wheel or blower vane due to foreign matter in vasion 3) Unbalanced rotating part Corrective action Turbocharger installation status check and repair of defective portion Turbocharger disassembly with repair or replacement, or perfect removal of foreign matters in case of foreign matter invasion Repair or replacement of rotating part
139
9. Starting Motor
9. STARTING MOTOR
As a representative example of starter, the one for 4TNV94L 98 and 4TNV106 (T) is shown in this chapter.
9.1 For 4TNV94L/ 98

9.1.1 Specifications
Manufacturers model (Hitachi) Code Nominal output Weight Revolution direction (as viewed from pinion) Engagement system No-load Terminal voltage/current Revolution Terminal voltage/current Torque kW kg V/A rpm V/A Nm(kgf m) V S13-204 129900-77010 2.3 5.5 Clockwise Magnetic shift 11/140 or less 4100 or above 2.5/1050 or less 24.5(2.5) or above Overrunning 8.6 or less M3/9 Dry (none) Standard Wet (with) Option S13-205 129900-77020
Loaded
Clutch system Pinion projection voltage (at 100 ) Pinion DP or module/number of teeth difference (O-ring, oil seal) Application
140
9. Starting Motor
9.1.2 Components
141
9. Starting Motor
9.1.3 Troubleshooting
142
9. Starting Motor
9.1.4 Names of parts and disassembly procedure

(1) Disassembling order
1) Nut M8 (Disconnect the connecting wire.) 2) Screw M4 (2) 3) Through bolt M5 (2) 4) Rear cover 5) Brush holder 6) Yoke assy. 7) Armature 8) Bolt M6 (2) 9) Magnetic switch 10) Dust cover 11) Shift lever 12) Screw M4 (3) 13) Bearing retainer 14) Gear case 15) Pinion stopper clip 16) Pinion stopper 17) Return spring 18) Pinion shaft 19) Clutch assy. See the disassembly drawing.
Disassembly drawing
143
9. Starting Motor
(2) Disassembly procedure

1) Nut M8 Remove the magnetic switch nut M8 (12 mm), and disconnect the connecting wire.
2) Screw M4 (2) 3) Through bolt M5 (2) 4) Rear cover Remove the M4 screw fastening the brush holder and remove through bolt M5 for rear cover removal.
5) Brush holder Pull the brush spring up with the brush spring puller. On the negative (-) side, bring the brush spring into contact with the side of the brush for lifting from the commutator surface. On the positive (+) side, extract the brush from the brush holder.
144
9. Starting Motor
6) Yoke Assy. 7) Armature Remove the brush holder. The armature and yoke assy can now be removed.
8) Bolt M6 (2) 9) Magnetic switch Remove bolt M6 (10 mm), and the magnetic switch can be removed.
10) Dust cover 11) Shift lever Take the dust cover out from the gear case. The shift lever can be removed.
145
9. Starting Motor
12) Screw M4 (3) 13) Bearing retainer 14) Gear case Remove screw M4, and the bearing retainer and clutch assy can be removed.
15) Pinion stopper clip Remove the bearing retainer at the edge and the bearing, and shift the pinion stopper toward the pinion. use a plain screwdriver and pry to remove the pinion stopper clip.
16) Pinion stopper 17) Return spring 18) Pinion shaft 19) Clutch Assy Remove the pinion stopper clip. The pinion stopper, return spring, pinion shaft and bearing retainer can be removed. Disassembly is completed now.
146
9. Starting Motor
9.1.5 Inspection and Maintenance

(1) Armature
(a) Commutator outside diameter Measure the commutator outside diameter and replace the commutator if the measured value is less than the limit.
mm Standard 36.5 Limit 35.5
(b) Armature coil continuity test Check continuity between commutator segments with a multimeter. Good if continuity exists.
In case of no continuity (coil disconnection), replace the armature.
(c) Armature coil insulation test Inspect the continuity between a commutator segment and the shaft or core with a multimeter. Good if no continuity exists.
If continuity exists (coil short circuit), replace the armature.
147
9. Starting Motor
(d) Armature and commutator run-out Use a dial gage and measure the armature core run-out and commutator run-out. Correct or replace if the limit is exceeded.
mm Standard Armature Commutator 0.03 0.03 Limit 0.2 0.2
(e) Commutator surface inspection If the commutator surface is roughened, grind with #500 to #600 emery cloth.
(f) Commutator insulation depth Measure the depth of the insulating material between commutator segments, and correct it if it is less than the limit.
mm Standard 0.5 0.8 Limit 0.2
148
9. Starting Motor
(2) Field coil

(a) Field coil continuity test Check continuity between field coil terminals. Good if continuity exists.
If no continuity (coil disconnection), replace the field coil.
(b) Field coil insulation test Check continuity between field coil terminal and yoke. Good if no continuity exists.
If continuity exists (coil short circuit), replace the armature.
(3) Brush
Measure the length of the brush. Replace with a good one if the length is less than the limit.
mm Standard 15 Limit 9
149
9. Starting Motor
(4) Brush holder

(a) Brush holder insulation test Check the continuity between the brush holder (+ side) and base (- side) with a multimeter. Good if no continuity exists.
If continuity exists (insulation defect), replace the brush holder.
(b) Brush spring inspection Inspect the brush spring pressure.

N(kgf) Standard spring force 31 39 (3.1 3.9)
(5) Magnetic switch

When the starting motor is wetted with water, always replace the magnetic switch with a new even if the function is normal. (a) Shunt coil continuity test Check the continuity between the S terminal and the switch body. Good if continuity exists. If no continuity (coil disconnection), replace the magnetic switch.
150
9. Starting Motor
(b) Series coil continuity test Check continuity between the S and M terminals. Good if continuity exists.
If no continuity (coil disconnection), replace the magnetic switch.
(c) Contact continuity test Depress the magnetic switch with the plunger at the bottom. Check continuity between the B and M terminals with a multimeter. Good if continuity exists.
If no continuity (coil continuity defect), replace the magnetic switch.
(6) Pinion clutch

(a) Pinion inspection Manually rotate the pinion. Inspect if it is rotated smoothly in the driving direction, and is locked in the opposite direction. Replace the pinion clutch if abnormal.
151
9. Starting Motor
(b) Pinion sliding inspection Check if the pinion slide smoothly in the axial direction. If damaged, rusted or heavy in sliding, repair it. If grease is applied too much on the pinion shaft, sliding becomes heavy.
(c) Ball bearing inspection Rotate the ball bearing while holding the outer race with fingertips. Inspect if it is sticking or it there is play.

Brush Spring force Standard height/wear limit Standard diameter/limit diameter Difference between maximum Repair limit/repair accuracy and minimum diameter Mica undercut depth chips Repair limit/repair accuracy Armature fount Bearing type Armature rear Pinion front Pinion rear L dimension (pinion projection length) Nominal number N(kgf) mm mm mm mm mm 35(3.6) 15/9 0.27/0.60 36.5/35.5 0.2/0.03 0.2/0.5 0.8 6903DDU 608DDU 60004DDU 6904DDU 0.3-1.5
Magnetic switch resistance, series coil/shunt coil (at 20 )
Commutator
152
9. Starting Motor
9.1.7 Assembly
The assembly procedure is the reverse of the disassembly procedure, but pay attention to the following points:
(1) Grease application points

Gears in the gear case Shift lever operating portion Pinion sliding portion Magnetic switch plunger sliding portion Use the specified grease as below table at all points.
Pinion and magnetic switch plunger sliding portions Gears Shift lever operating portion NPCFG-6A MALTEMP SRL ALBANIA No.1
(2) Magnetic switch assembly

1) Install the shift lever on the magnetic switch with the torsion spring in-between.
2) For installation on the gear case, install the magnetic switch with the shift lever on the gear case after pulling the pinion out. Fix the magnetic switch by tightening a built-in bolt M6. Do not forget to install the dust cover (adjusting shim).
153
9. Starting Motor
(3) Pinion projection length

Connect the positive (+) lead from the battery to terminal S and negative (-) lead to terminal M. Turn the switch ON and measure the pinion moving distance L in the thrust direction. Perform this test within 10 seconds.
mm Standard L 0.3 1.5
Note: Before measuring the dimension, pull the pinion out lightly in the direction of the arrow.
If the measured L dimension is outside the standard range, either insert or remove the dust cover (adjusting shim 0.5 mm, 0.8 mm) for adjustment.
154
9. Starting Motor
9.1.8 Characteristic test

Since the characteristics can be checked roughly by means of a simple no-load test as explained below. NOTE: Complete the test quickly since the rating of the starting motor is 30 seconds.
(1) No-load test

Fix the starting motor on a test bench and connect wiring as shown in Fig.31. When the switch is closed, a current flows in the starting motor, which is rotated at no-load. Measure the current, voltage and number of revolutions then and check if they satisfy the specified characteristics.
155
9. Starting Motor
9.2 For 4TNV106(T)

Manufacturers model (Hitachi) Code Nominal voltage Nominal output Rating Revolution direction (as viewed from pinion) Clutch system Engagement system Pinion: Module/number of teeth Weight Pinion projection voltage (at 100 ) No-load Terminal voltage/current Revolution Terminal voltage/current Loaded Torque Revolution V kW Sec kg V V/A rpm V/A N m(kgfm) min-1 S13-138 129953-77010 12 3.0 30 Clockwise Roller clutch Magnetic shift M3/9 7.3 8 or less 12/180 or less 3000 or more 9/500 16.7(1.7) or more 1270 or more
9.2.2 Congiguration drawing
156
9. Starting Motor
157
9. Starting Motor
9.2.4 Component names and disassembly procedure

(1) Disassembly procedure
1) Disconnect the lead. 2) Remove the magnetic switch. 3) Remove the rear cover. 4) Remove the brush holder. 5) Disassemble the gear case and center bracket. 6) Remove the shift lever pin. 7) Remove the gear case dust cover. 8) Remove the pinion.
(2) Disassembly diagram
158
9. Starting Motor
9.2.5 Disassembly procedure

(1) Disconnecting the lead
Loosen the M8 nut (12mm) of the magnetic switch and disconnect the lead.
159
9. Starting Motor
(2) Removal of magnetic switch

Remove the M6 bolts (10mm 2).
160
9. Starting Motor
(3) Removal of rear cover

Remove the brush holder tightening screws (4mm 2) and the M5 through bolts ( 2). Next, disconnect the rear cover from the yoke using a screwdriver.
161
9. Starting Motor
(4) Removal of brush holder

For the negative () brush, bring the brush spring into contact with the side of the brush for lifting from the commutator surface. For the positive (+) brush, extract the pull out the brush from the brush holder. After the brush holder is removed, the armature and yoke can be disassembled.
162
9. Starting Motor
(5) Separating gear case from center bracket

Remove three M6 bolts (10mm) fastening the gear case to the center bracket. After removal of the M6 bolts, the center bracket and oil seal can be removed.
163
9. Starting Motor
(6) Removal of shift lever pin

Remove the M6 nut (10mm) and pull out the shift lever pin. Now. the dustcover, shift lever, gear case and gear shaft can be removed.
164
9. Starting Motor
(7) Removal of gear case dust cover

Remove the two M5 bolts (using 4 mm hexagon wrench) to disassemble the dust cover from the gear case.
165
9. Starting Motor
(8) Removal of pinion

Slide the pinion stopper towards the pinion and remove the pinion stopper clip using a screwdriver.
166
9. Starting Motor
9.2.6 Inspection and maintenance

(1) Armature
1) Check the commutator for rough surface. If so, smooth the surface using #500 to #600 emery cloth. If the outside periphery of the commutator has been deflected over 0.2 mm, repair by a lathe.
2) Measure the depth of the insulating material between commutator segments, and correct if it is less than 0.2 mm.
167
9. Starting Motor
3) Armature coil continuity and earth tests

Test type Continuity test Earth test Measurement point Across commutator Between commutator and shaft or armature Normal Yes None Abnormal (cause) None (open circuit) Yes (short-circuiting)
Replace if needed.
168
9. Starting Motor
(2) Field coil

1) Field coil continuity and earth tests
Test type Continuity test Earth test Measurement point Across commutator Between commutator and shaft or armature Normal Yes None Abnormal (cause) None (open circuit) Yes (short-circuiting)
Replace if needed.
169
9. Starting Motor
(3) Brush
1) Check wear of the brush and the brush spring force.
170
9. Starting Motor
2) Check of brush movement If the brush does not move smoothly, inspect the brush holder for bending and the brush holder sliding surface for dirt. Repair or clean as needed. 3) Check the continuity between the insulated brush holder (positive (+)) and the brush holder base (negative (-)). If they are electrically continuous, replace since the holder is grounded.
171
9. Starting Motor
(4) Magnetic switch continuity test

Test type Shunt coil Series coil Measurement point Between C and ground C and M Normal Yes None Abnormal (cause) None (open circuit) Yes (short-circuiting)
Replace if needed.
S13-138 Resistance (at 20 ) Shunt coil Series coil 0.6 0.218
172
9. Starting Motor
(5) Pinion
1) Check the pinion teeth for wear and damage. Replace with a new one, if necessary. 2) Check if the pinion slides smoothly. If it is damaged or rusted or does not slide smoothly, repair. 3) Check springs for damage, and replace if necessary.
(6) Ball bearing

If abnormalities such as irregular noises are detected to the ball bearing, replace with a new one.
9.2.7 Assembly
The assembly procedure is reverse of the disassembly procedure, but pay attention to the following points.
(1) Apply grease as instructed below.

Greasing point Sliding portions and head of plunger Pinion metal and metal portions of gear case Spline portions of pinion Sliding portions of shift lever Deceleration gear Grease type NPC-FC6A Grease MALTEMP SRL Grease
(2) Armature thrust

No adjustments are needed for the thrust.
(3) Gear shaft thrust

Some thrust washers of 1.0 and 0.25 mm thickness are provided between the center bracket and gear shaft supporting surface. Make sure to check them at reassembly. If washers are deformed or worn, replace them with new ones. The appropriate thrust is from 0.05 to 0.3mm. If it is over 0.3mm, and the appropriate thrust washer, but pay attention so that the thrust is not 0.
173
9. Starting Motor
9.2.8 Adjustment
(1) Pinion projection length L by magnetic switch
Measure the pinion moving distance L (0.3 to 1.5mm) in the thrust direction when the pinion is protruded by the magnetic switch. If the distance L is outside the standard range, adjust by the dust cover as shown below.
174
9. Starting Motor

Brush Spring force N(kgf) Standard / Limit height Outside diameter Commutator Deflection Depth of insulation mica Armature shaft diameter Standard dimensions Bearing on gear case side Sliding portion of pinion Ball bearing Armature Standard Limit Limit Correction accuracy Limit Correction accuracy Front Rear Gear shaft diameter Hole diameter Shaft diameter Hole diameter Front Rear 31.4 (3.2) 18/6 37 36 0.2 0.05 0.2 0.5 0.8 25 12 13.95 13.968 14.00 14.018 13.95 13.968 14.03 14.05 6905DDU 6001DDU 0.3 1.5
Length L (pinion projection length)
175
10. Alternator
10. ALTERNATOR
As a representative example of alternator, the alternator of 40A is shown in this chapter.
10.1 The 40A Alternator for 3TNV84 and other models

10.1.1 Components
(1) Parts related to the alternator
(2) Alternator components of the disassembly and assembly
176
10. Alternator
Manufacturers model (Hitachi) Code Rating Battery voltage Nominal output (13.5V heat) Rated revolution Operating revolution Grounding characteristics Direction of revolution (viewed from pulley) Integrated regulator Weight Pulley (outside diameter) Belt shape kg mm V A min-1 min-1 ACFA68 129423-77200 Continuous 12 40 5,000 1,350 18,000 Minus side grounding Clockwise IC regulator 2.8 69.2 Type A
10.1.3 Wiring diagram
[NOTICE] 1) Don't do miss-wiring and short-circuit of each terminal. 2) Dont short-circuit between IG and L. (Connect it through the charge lamp.) 3) Dont connect a load between L and E. 4) Don't remove a battery terminal and a B terminal when rotating. 5) Shut out a battery switch during the alternator stop. 6) Tightening torque of each terminal: 1.7-2.3N m (17-23kgf cm)
177
10. Alternator
10.1.4 Standard output characteristics

The standard output characteristics of this alternator are shown as the right figure.
10.1.5 Inspection
(1) V belt inspection
1) Inspect the matter whether there are not crack, stickiness and wear on the belt visually. Check that a belt doesn't touch the bottom part of the pulley groove. If necessary, replace the V belt set. 2) V belt tension: (Refer to 2.2.2 in Chapter 2.)
(2) Visual check of wiring and check of unusual sound

1) Confirm whether wiring is right or there is no looseness of the terminal part. 2) Confirm that there is no unusual sound from the alternator during the engine operation.
(3) Inspection of charge lamp circuit

1) Move a start switch to the position of on. Confirm lighting of the charge lamp. 2) Start an engine, and confirm the lights-out of the lamp. Repair a charge lamp circuit when a lamp doesn't work.
178
10. Alternator
179
11. Electric Wiring
11. ELECTRIC WIRING

11.1 Electric Wiring Diagram
180
11. Electric Wiring
11.2 PRECAUTION ON ELECTRIC WIRING

11.2.1 Alternator
In the cases listed below the warranty shall not be deemed to apply. Please be sure to read these conditions carefully when planning to use it with other equipment. Also be certain to give appropriate guidance on usage to the user.
(1) When the battery cable can be connected backwards

The alternator diode will be damaged and recharging made impossible if the plus and minus ends of the battery cable are confused. The stator coil will also be burned as a result. To prevent this, supply the user with a cable of such a length or structure that the plus and minus ends cannot be confused. Also warn the user not to connect the cable backwards.
(2) When charging output voltage is used for control purposes

The engine speed at starting is not proportional to the output voltage of the alternator, so this output voltage must not be used for any control systems. It is especially wrong to use it for the control signal of the safety relay for cutting the starter motor because this will damage the starter motor and cause engine starting failure.
(3) When the L line is used for control purposes

Damage to the alternator and related equipment will not be warranted without such prior consultation.
(4) Non-use of the wiring diagram

Use without prior consultation of any wiring diagram other than that provided removes any breakdown of any electrical equipment from the warranty.
(5) Regarding lamp control

Once the charge lamp goes out after the start of charging, it does not come on again even if the engine speed falls and charging is insufficient. The lamp will not light again if the charging circuit is normal. The lamp only comes on during operation if the alternator itself is broken or the drive V-belt breaks. However, when an LED is used for the charge lamp, the LED will shine faintly even during normal operation. This is due to the control system for the alternator lamp and is not an abnormality.
(6) Use of a non-specified V-belt

Use of a non-specified V-belt will cause inadequate charging and shorten the life of the belt. Use a belt of the specified type.
(7) Direct high pressure washing is prohibited

Water will enter the brush if the alternator is washed directly at high pressure, causing inadequate charging. Warn users not to use direct, high-pressure washing.
(8) Use of agricultural or other chemicals (direct contact or airborne)

Adhesion of agricultural and other chemicals, especially those with high sulfur content, to the IC regulator corrodes the conductor on the substrate, leading to over-charging (battery boiling) and charging malfunctions. Use without prior consultation removes any breakdown from the warranty.
181
11. Electric Wiring
11.2.2 Starter
(1) Starting performance in the case of using an untested battery

The starting performance of the engine is closely dependent on the battery capacity. This battery capacity is itself affected by the climate and the type of equipment installation. The details regarding ambient temperature and equipment installation vary depending on the OEM. Confer in advance after checking these conditions and fix the battery capacity on the basis of confirmatory tests.
(2) When the resistance of the battery cable exceeds the specified value
The combined total resistance of the battery cable in both directions between the starting motor and battery should be within the value indicated on the wiring diagram. The starting motor will malfunction or break down if the resistance is higher than the specified value.
(3) When the resistance of the starter circuit exceeds the specified value
The combined total resistance of the wiring between the starting motor and key switch (or power relay or safety relay, depending on the application) should be within the value indicated on the wiring diagram. Engine starting will be difficult if the resistance is higher than the specified value. This can also cause welding of the magnet switch at the point of contact and resultant burning of the armature coil.
(4) When there is no safety relay

Over-running (when the electric current flows for too long) is a major cause of starting failure. This burns the armature coil and causes clutch failure. Excessive work and failure of the key switch to return properly are the main causes of over-running. The user must be given sufficient warning about this. Be sure to use the safety relay to prevent over-running. This safety relay is supplied as an option. First when planning to install a safety relay at your own company. In the case of failure, our warranty will not be applied to all the electrical equipment.
(5) When there is too much rust due to the entry of water
The water-proofing of the starting motor is equivalent to R2 of JIS D 0203. This guarantees that there will be no damage from the sort of exposure encountered in rain or when water is poured on from a bucket. You should, however, avoid the use of high-pressure washing and steeping in water.
(6) Regarding the heat resistance of the starter motor

The starter motor has heat resistance for an ambient temperature of 80 and surface temperature of 100 . Insulators must be installed to prevent overheating when used near high temperature parts such as the exhaust system.
(7) Corrosion of magnet switch contact point by corrosive gas.

When using equipment with a dry clutch, ammonium gas generated by friction is liable to corrode the contact of the magnet switch. Be sure to install a vent in the clutch case.
182
11. Electric Wiring
11.2.3 Current limiter

(1) When an over-discharged battery is used

Use of booster starting with an over-discharged battery (when the voltage has dropped to 8V or less) will destroy other electrical equipment by generating an abnormally high voltage. A specialized battery charger should be used to recharge such an over-discharged battery (when the voltage has dropped to 8V or less).
(2) When checks for malfunctioning are not performed

When high voltage noise from other electrical equipment is impressed on the current limiter upon turning off the key switch, the current limiter can be damaged and cause loss of control over the output voltage. Other electrical equipment may also be damaged if this happens, so surge killers should be fitted to the electrical equipment whenever necessary. Be sure to check prior to mass production whether electrical noise might damage the current limiter by turning the key switch and other electrical equipment on and off while the engine is running, using both the vehicle and the wire harness that will be used in mass production.
(3) Removal of the battery cable during operation

The current limiter may malfunction if the battery cable and/or battery are removed during operation, depending on the kind of electrical equipment being used, causing loss of control over the output voltage. In such cases, the current limiter and other electrical equipment will be damaged by the generation of a continuous high voltage of 24-43V (for 5,000rpm dynamo). All electrical equipment falls outside the scope of the warranty under these circumstances. Be sure to warn the user not to remove the battery cable and/or battery during operation.
(4) If the battery cable can be attached in reverse

The current limiters SCR diode will be destroyed if the plus and minus ends of the battery cable are connected the wrong way around. This causes charging malfunctioning and burns the harness. Give the user a cable of such a length that it cannot be connected the wrong way and warn the user against connecting the cable backwards.
(5) Non-use of the wiring diagram

Use without prior consultation of any wiring diagram other than that provided by removes any breakdown of any electrical equipment from the warranty.
(6) Installation environment

Observe the following when installing the current limiter: 1) Do not install it on the engine. 2) Place it in a well-ventilated place with an ambient temperature of 65 or less. 3) Ensure that the cooling air flows in the right direction for the current limiters cooling fins. 4) Do not use the earth wire of the current limiter to earth any other electrical equipment.
183
11. Electric Wiring
11.2.4 Section area and resistance of electric wire

(1) Allowable maximum cable length Terminal resistance is not included.
Cable size mm2 3 5 8 15 20 30 40 50 60 85 100 Cable construction Element No. 41 65 50 84 41 70 85 108 127 169 217 Cable dia. 0.32 0.32 0.45 0.45 0.80 0.80 0.80 0.80 0.80 0.80 0.80 Resistance ( /m) 0.005590 0.003520 0.002320 0.001380 0.000887 0.000520 0.000428 0.000337 0.000287 0.000215 0.000168 2m
Note1
20m
Ref.
50m
Note2
(m) 0.36 0.57 0.86 1.45 2.25 3.85 4.67 5.93 6.97 9.30 11.90 3.58 5.68 8.62 14.49 22.55 38.46 46.73 59.35 69.69 93.02 119.05
(m) 8.94 14.20 21.55 36.23 56.37 96.15 116.82 148.37 174.22 232.56 297.62
(m)
Note1) Allowable maximum resistance of Battery cable Note2) Allowable maximum resistance of Starting motor circuit
(2) Terminal resistance

Generally, a terminal resistance is 15m per coupler and 0 per screw setting. This resistance should be included in allowable maximum resistance when the cable length is planned.
184
12. Service Standards
12. SERVICE STANDARDS

12.1 Engine Tuning
No. 1 Inspection item Gap at intake/exhaust valve heads TNV82A 98 mm 4TNV106(T) Between alternator Used part and crank pulley New part V-belt tension Between alternator Used part mm and radiator fan New part at 98N (10kgf) Between radiator fan Used part and crank pulley New part 3TNV82A TNV88(VM) Fuel injection 4TNV94L 106(T) pressure 2 MPa (kgf/cm ) 3TNV82A TNV88(CL) TNV82A TNV84 3/4TNV84T TNV88-106 3TNV82A,84 3TNV84T,88 4TNV84(T),88 4TNV94L 98(T) 4TNV106(T) 3TNV82A Lubricating oil 3TNV84(T)/88 capacity 4TNV84(T)/88 (oil pan) (Liter) 4TNV94L/98(T) 4TNV106(T) (CL class) 4TNV106(T) (VM class) 3TNV82A 98 4TNV98T Lubricating oil 4TNV106(T) pressure (VM, WO balancer) MPa (kgf/cm2) 4TNV106(T) (CL, WO balancer) 4TNV106(T) (VM, W balancer) Oil pressure switch operating pressure MPa (kgf/cm2) Compression pressure (at 250 min-1) MPa (kgf/cm2) Coolant water Capacity (Only engine body) (Liter) Standard 0.15 0.25 0.25 0.35 10 14 8 12 7 10 5 8 9 13 7 11 21.57 22.55 (220 230) 19.6 20.6 (200 210) 3.16(31) 0.1(1) 3.24(33) 0.1(1) 2.94(30) 0.1(1) 3.43(35) 0.1(1) 1.8 2.0 2.7 4.2 6.0 Full Effective 5.5 1.9 6.7 2.8 7.4 3.4 10.5 4.5 14.0 9.0 14.0 7.5 at rated speed 0.29(3.0) 0.39(4.0) 0.39(4.0) 0.49(5.0) 0.31(3.2) 0.49(5.0) 0.34(3.5) 0.44(4.5) 0.050.01 (0.50.1) valve opening temperature deg. C 69.5 72.5 80 84 (deg.C) 107 113 Full opening lift (mm) (temperature) 8 or above (85 deg.C) 10 or above (95 deg.C) 0.06(0.6) or above Limit Reference page 2.2.6(4)
2.2.2.(2)
2.45(25) 0.1(1) 2.55(26) 0.1(1) 2.45(25) 0.1(1) 2.75(28) 0.1(1) at low idle speed
2.2.6.(3)
3.3
2.2.1.(4)
2.2.1.(3)
Thermostat
All models
2.7
10
All models option Thermo switch actuating temperature
2.4.2
185
12.2 Engine Body

12.2.1 Cylinder head
(1) Cylinder head
Inspection item Combustion surface distortion 3TNV82A (2-valve head) TNV84 88 (2-valve head) 4TNV84T(4-valve) mm 4TNV94L 98(T) (4-valve head) 4TNV106(T) (4-valve head) Seat angle Deg. Seat correction angle Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust deg. mm Standard 0.05 or less 0.35 0.55 0.30 0.50 0.30 0.50 0.30 0.50 0.36 0.56 0.35 0.55 0.5 0.7 0.7 0.9 120 90 40, 150 Limit 0.15 0.8 0.8 0.8 0.8 0.8 0.8 1.0 1.2 4.2.6. 4.2.5.(1) Reference page
Valve sink
Valve seat (2-valve, 4-valve)
186
(2) Intake/exhaust valve and guide

Inspection item Guide inside diameter Intake 3TNV82A (2-valve head) Exhaust Valve stem outside diameter Clearance Guide inside diameter Valve stem outside diameter Clearance Guide inside diameter 4TNV84 3TNV84(T) 3/4TNV88 (2-valve head) Intake Valve stem outside diameter Clearance Guide inside diameter Exhaust Valve stem outside diameter Clearance Guide inside diameter Intake 4TNV84T (4-valve head) Exhaust Valve stem outside diameter Clearance Guide inside diameter Valve stem outside diameter Clearance Guide inside diameter Intake 4TNV94L 4TNV98(T) (4-valve head) Exhaust Valve stem outside diameter Clearance Guide inside diameter Valve stem outside diameter Clearance Guide inside diameter Intake 4TNV106(T) (4-valve head) Exhaust Valve stem outside diameter Clearance Guide inside diameter Valve stem outside diameter Clearance 3TNV82A 4TNV84, 4TNV88 4TNV84T 4TNV106(T) Valve guide driving-in method 3TNV84(T), Standard 7.000 7.015 6.945 6.960 0.040 0.070 7.000 7.015 6.940 6.955 0.045 0.075 8.010 8.025 7.955 7.975 0.035 0.070 8.015 8.030 7.955 7.960 0.045 0.075 6.000 6.015 5.960 5.975 0.025 0.055 6.000 6.015 5.945 5.960 0.040 0.070 7.000 7.015 6.945 6.960 0.040 0.070 7.000 7.015 6.940 6.955 0.045 0.075 7.008 7.020 6.945 6.960 0.048 0.075 7.008 7.020 6.960 6.975 0.033 0.060 11.7 12.0 14.7 15.0 8.2 8.5 9.7 10.0 13.4 13.6 Cold-fitted Limit 7.08 6.90 0.18 7.08 6.90 0.18 8.10 7.90 0.18 8.10 7.90 0.18 6.08 5.90 0.15 6.08 5.90 0.17 7.08 6.90 0.17 7.08 6.90 0.17 7.08 6.92 0.16 7.08 6.90 0.18 4.2.7. 4.2.5.(2) mm Reference page
Valve guide projection from cylinder head
4TNV94L, 4TNV98(T)
187
(3) Valve spring

Inspection item 3TNV82A (2-valve) 4TNV84,3TNV84(T), 4TNV88 (2-valve) Free length 4TNV84T (4-valve) 4TNV94L, 4TNV98(T), (4-valve) 4TNV106(T) (4-valve) 3TNV82A (2-valve) 4TNV84, 3TNV84(T), 4TNV88 (2-valve) Inclination 4TNV84T (4-valve) 4TNV94L, 4TNV98(T), (4-valve) 4TNV106(T) (4-valve) Standard 44.4 42.0 37.4 39.7 50.6 Limit 43.9 41.5 36.9 39.2 50.1 1.4 1.4 1.3 1.4 1.5 4.2.5.(4) mm Reference page
(4) Rocker arm and shaft

Model Inspection item Arm shaft hole diameter TNV82A 88 Shaft outside diameter Clearance Arm shaft hole diameter 4TNV94L/98(T)/106(T) Shaft outside diameter Clearance Standard 16.000 16.020 15.966 15.984 0.016 0.054 18.500 18.520 18.470 18.490 0.010 0.050 Limit 16.07 15.94 0.13 18.57 18.44 0.13 4.2.5.(5) mm Reference page
(5) Push rod

Inspection item Bend Standard Limit 0.03 mm Reference page 4.2.5.(7)
188
12.2.2 Gear train and camshaft

(1) Camshaft
Inspection item Side gap Bending (1/2 the dial gage reading) 3TNV82A-TNV88 Cam height 4TNV94L 98 4TNV106(T) Shaft outside diameter / Metal inside diameter Bushing inside diameter Gear side Camshaft outside diameter Clearance Bushing inside diameter TNV82A TNV88 Intermediate Camshaft outside diameter Clearance Bushing inside diameter Wheel side Camshaft outside diameter Clearance Bushing inside diameter Gear side Camshaft outside diameter Clearance Bushing inside diameter 4TNV94L/98(T) Intermediate Camshaft outside diameter Clearance Bushing inside diameter Wheel side Camshaft outside diameter Clearance Bushing inside diameter Gear side Camshaft outside diameter Clearance Bushing inside diameter 4TNV106(T) Intermediate Camshaft outside diameter Clearance Bushing inside diameter Wheel side Camshaft outside diameter Clearance 44.990 45.055 44.925 44.950 0.040 0.130 45.000 45.025 44.910 44.935 0.065 0.115 45.000 45.025 44.925 44.950 0.050 0.100 49.990 50.055 49.925 49.950 0.040 0.130 50.000 50.025 49.910 49.935 0.065 0.115 50.000 50.025 49.925 49.950 0.05 0.100 57.980 58.050 57.910 57.940 0.040 0.140 58.000 58.030 57.895 57.925 0.075 0.135 58.000 58.030 57.910 57.940 0.050 0.120 45.130 44.890 0.240 45.100 44.875 0.225 45.100 44.890 0.210 50.130 49.890 0.240 50.100 49.875 0.225 50.100 49.890 0.210 58.105 57.875 0.250 58.105 57.860 0.245 58.105 57.875 0.230 4.3.5(1) Standard 0.05 0.20 0 0.02 38.600 38.800 43.400 43.600 50.900 51.100 Limit 0.30 0.05 38.350 43.150 50.650 4.3.5(1) mm Reference page 4.3.4
189
(2) Idle gear shaft and bushing

Inspection item Shaft outside diameter Bushing inside diameter Clearance Standard 45.950 45.975 46.000 46.025 0.025 0.075 Limit 45.900 46.075 0.175 4.3.5(2) mm Reference page
(3) Backlash of each gear

Model 3TNV82A 88 4TNV94L 4TNV98(T) 4TNV106(T) Inspection item Crank gear, cam gear, idle gear, fuel injection pump gear and PTO gear Crank gear, cam gear, idle gear, fuel injection pump gear and PTO gear Lubricating oil pump gear Balancer drive gear (only for 4TNV106(T)) Standard 0.07 0.15 0.08 0.14 0.09 0.15 0.12 0.18 Limit 0.17 0.16 0.17 0.20 4.3.4. mm Reference page
12.2.3 Cylinder block

(1) Cylinder block
Inspection item 3TNV82A TNV84 Cylinder inside diameter TNV88 4TNV94L 4TNV98 4TNV106(T) Cylinder bore Roundness Inclination Standard 82.000 82.030 84.000 84.030 88.000 88.030 94.000 94.030 98.000 98.030 106.000 106.030 0.01 or less Limit 82.200 84.200 88.200 94.130 98.130 106.130 0.03 4.4.5.(1) mm Reference page
190
(2) Crankshaft
Inspection item Bending (1/2 the dial gauge reading) Pin outside diameter 3TNV82A Metal inside diameter Metal thickness Clearance Pin outside diameter TNV84 88 Crank pin 4TNV94L 98 Metal inside diameter Metal thickness Clearance Pin outside diameter Metal inside diameter Metal thickness Clearance Pin outside diameter 4TNV106(T) Metal inside diameter Metal thickness Clearance Journal outside diameter 3TNV82A Metal inside diameter Metal thickness Clearance TNV84 88 Selective pairing Crank journal 4TNV94L 98 Selective pairing 4TNV106(T) Selective pairing Journal outside diameter Metal inside diameter Metal thickness Clearance Journal outside diameter Metal inside diameter Metal thickness Clearance Journal outside diameter Metal inside diameter Metal thickness Clearance Standard 42.952 42.962 43.000 43.042 1.487 1.500 0.038 0.090 47.952 47.962 48.000 48.026 1.492 1.500 0.038 0.074 57.952 57.962 58.000 58.026 1.492 1.500 0.038 0.074 63.952 63.962 64.016 64.042 1.984 1.992 0.054 0.090 46.952 46.962 47.000 47.032 1.987 2.000 0.038 0.080 53.952 53.962 54.000 54.020 1.995 1.990 0.038 0.068 64.952 64.962 65.000 65.020 1.995 2.010 0.038 0.068 75.952 75.962 76.014 76.034 2.488 2.503 0.052 0.082 0.150 63.902 0.150 46.902 0.150 53.902 0.150 64.902 0.150 75.902 0.150 4.4.5.(2) Limit 0.02 42.902 0.150 47.902 0.150 57.902 mm Reference page
191
(3) Thrust bearing

Inspection item Crankshaft side gap All models Standard 0.13 0.23 Limit 0.28 mm Reference page 4.4.4
(4) Piston and ring

Piston Inspection item 3TNV82A 3,4TNV84(T) Piston outside diameter (Measure in the direction vertical to the piston pin.) 3,4TNV88 4TNV94L 4TNV98(T) 4TNV106(T) 3TNV82A 3,4TNV84(T) Piston diameter measure position (Upward from the bottom end of the piston) 3,4TNV88 4TNV94L 4TNV98(T) 4TNV106(T) Hole inside diameter 3TNV82A Pin outside diameter Clearance Hole inside diameter TNV84 88 Piston pin 4TNV94L 98 Pin outside diameter Clearance Hole inside diameter Pin outside diameter Clearance Hole inside diameter 4TNV106(T) Pin outside diameter Clearance Standard 81.950 81.980 83.945 83.975 87.945 87.975 93.945 93.955 97.940 97.950 105.930 105.960 16 24 24 22 22 30 23.000 23.009 22.995 23.000 0.000 0.014 26.000 26.009 25.995 26.000 0.000 0.014 30.000 30.009 29.989 30.000 0.000 0.020 37.000 37.011 36.989 37.000 0.000 0.022 Limit 81.905 83.900 87.900 93.900 97.895 105.880 23.039 22.965 0.074 26.039 25.965 0.074 30.039 29.959 0.080 37.039 36.959 0.080 4.4.5.(4) mm Reference page
192
Piston ring Model Inspection item Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Ring groove width Ring width Side clearance End clearance Standard 2.065 1.970 0.075 0.200 2.035 1.970 0.045 0.200 4.015 3.970 0.025 0.200 2.060 1.970 0.070 0.200 2.025 1.970 0.035 0.200 4.015 3.970 0.025 0.200 2.040 1.940 0.080 0.250 2.080 1.970 0.090 0.450 3.015 2.970 0.025 0.250 2.520 2.440 0.060 0.300 2.070 1.970 0.080 0.450 3.015 2.970 0.025 0.300 2.080 1.990 0.110 0.400 2.050 1.990 0.080 0.400 4.030 3.990 0.060 0.400 2.075 1.990 0.105 0.400 2.040 1.990 0.070 0.400 4.030 3.990 0.060 0.400 2.060 1.960 0.120 0.450 2.095 1.990 0.125 0.650 3.030 2.990 0.060 0.450 2.540 2.460 0.100 0.450 2.085 1.990 0.115 0.600 3.030 2.990 0.060 -0.500 limit 1.950 0.490 2.150 1.950 0.200 0.490 4.130 3.950 0.180 0.490 1.950 0.490 2.140 1.950 0.190 0.490 4.130 3.950 0.180 0.490 1.920 0.540 2.195 1.950 0.245 0.730 3.130 2.950 0.180 0.550 2.420 0.540 2.185 1.950 0.235 0.680 3.130 2.950 0.180 0.600 mm Reference page
Top ring
3TNV82A TNV84
Second ring
Oil ring
Top ring
TNV88
Second ring
Oil ring
4.4.5.(4)
Top ring
4TNV94L/98
Second ring
Oil ring
Top ring
4TNV106(T)
Second ring
Oil ring
193
(5) Connecting rod

Inspection item Thrust clearance Rod small end Model Item Bushing inside diameter 3TNV82A Pin outside diameter Clearance Bushing inside diameter TNV84-88 Pin outside diameter Clearance Bushing inside diameter 4TNV94L/98 Pin outside diameter Clearance Bushing inside diameter 4TNV106(T) Pin outside diameter Clearance Standard 23.025 23.038 22.995 23.000 0.025 0.043 26.025 26.038 25.995 26.000 0.025 0.043 30.025 30.038 29.987 30.000 0.025 0.051 37.025 37.038 36.989 37.000 0.025 0.049 Limit 23.068 22.967 0.101 26.068 25.967 0.101 30.068 29.959 0.109 37.068 36.961 0.107 4.4.5.(5) Standard 0.2 0.4 Limit mm Reference page 4.4.4 mm Reference page
(6) Tappet
Inspection item Tappet hole (block) inside diameter TNV82A-88 Tappet stem outside diameter Clearance Tappet hole (block) inside diameter 4TNV94L 98 Tappet stem outside diameter Clearance Tappet hole (block) inside diameter 4TNV106(T) Tappet stem outside diameter Clearance Standard 12.000 12.025 11.975 11.990 0.010 0.050 12.000 12.018 11.975 11.990 0.010 0.043 14.000 14.018 13.966 13.984 0.015 0.052 Limit 12.045 11.955 0.090 12.038 11.955 0.083 14.038 13.946 0.092 4.4.5.(6) mm Reference page
194
12.3 Lubricating Oil System (Trochoid Pump)

(1) Outside clearance of outer rotor
Model 3TNV82A 88 4TNV94L/98 4TNV106(T) Standard 0.12 0.21 0.100 0.155 0.100 0.165 Limit 0.30 0.25 0.25 5.5.1(1) mm Reference page
(2) Side clearance of outer rotor

Model 3TNV82A 88 4TNV94L/98 4TNV106(T) Standard 0.02 0.07 0.05 0.10 0.03 0.12 Limit 0.12 0.15 0.17 5.5.1(1) mm Reference page
(3) Inside clearance of inner rotor

Item Inside clearance of inner rotor Width across flat clearance of inner rotor Parts Gear boss diameter Rotor diameter Width across flat of Gear boss Width across flat of rotor Standard 53.05 53.15 53.45 53.55 49.45 49.75 0.2 0.6 49.95 50.05 0.7 Standard 0.3 0.5 Limit 0.6 5.5.12 mm Reference page
(4) Rotor shaft clearance

Model Inspection item Gear case bearing I.D. 4TNV94L/ 98 Rotor shaft O.D. Rotor clearance Gear case bearing I.D. 4TNV106(T) Rotor shaft O.D. Rotor clearance Standard 12.980 13.02 12.955 12.975 0.035 0.065 13.00 13.02 12.955 12.965 0.035 -0.065 Limit 13.05 12.945 0.105 13.05 12.945 0.105 5.5.1(3) mm Reference page
195
13. Tightening Torque for Bolts and Nuts
13. TIGHTENING TORQUE for BOLTS and NUTS

13.1 Tightening Torques for Main Bolts and Nuts
Part and engine model 3TNV82A Cylinder head bolt TNV84 88 4TNV94L 98 4TNV106(T) 3TNV82A Connecting rod bolt TNV84 88 4TNV94L 98 4TNV106(T) Flywheel set bolt TNV82A 88 4TNV94L 98 106(T) 3TNV82A Bearing cap set bolt TNV84 88 4TNV94L 98 4TNV106(T) Crankshaft pulley set bolt Fuel nozzle set bolt Fuel pump drive gear set nut Fuel injection pipe set bolt Fuel return pipe joint bolt Rocker arm cover set bolt EPA flange set bolt TNV82A 88 4TNV94L 98 106(T) TNV82A 88 4TNV94L 98 106(T) TNV82A 88 4TNV94L 98 106(T) TNV82A 88 4TNV94L 98 106(T) 4TNV94L 98 106(T) 4TNV106(T) 4TNV106(T) Thread diameter pitch mm M9 1.25 M10 1.25 M11 1.25 M13 1.5 M8 1.0 M9 1.0 M10 1.0 M11 1.0 M10 1.25 M14 1.5 M10 1.25 M12 1.5 M11 1.25 M14 1.5 M14 1.5 M14 1.5 M8 1.25 M8 1.25 M14 1.5 M18 1.5 M12 1.5 M12 1.5 M6 1.0 M8 1.25 M18 1.5 Tightening torque Lubricating oil Reference application page (thread portion, Nm(kgf m) and seat surface) 61.7 65.7 (6.3 6.7) 85.3 91.1 (8.7 9.3) Applied 4.2.4 103.1 112.9 (10.5 11.5) 188.0 197.8 (19.0 20.0) 37.2 41.2 (3.8 4.2) 44.1 49.0 (4.5 5.0) Applied 4.4.4 53.9 58.8 (5.5 6.0) 78.5 83.4 (8.0 8.5) 83.3 88.2 (8.5 9.0) Applied 4.3.4 186.2 205.8 (19 21) 76.4 80.4 (7.8-8.2) 93.2 98.1 (9.5 10.5) Applied 4.4.4 108.1 117.9 (11.0 12.0) 186.2 205.8 (19 21) 112.7 122.7 (11.5 12.5) Applied 4.3.4 107.9 127.5 (11.0 13.0) 24.4 28.4 (2.5 2.9) Not applied 22.6 28.4 (2.3 2.9) 78 88(8 9) Not applied 4.3.4 113 123 (11.5 12.5) 29.4 34.3 (3.0 3.5) Not applied 19.6 24.5 (2.0 2.5) 7.8 9.8 Not applied (0.8 1.0) 16.7 22.5 Not applied (1.7 2.3) 113 123 Not applied (11.5 12.5)
196
13. Tightening Torque for Bolts and Nuts
13.2 Tightening Torques for Standard Bolts and Nuts

Tightening torque Nm(kgf-m) 9.8 11.8 M6 1 (1.0 1.2) 22.6 28.4 M8 1.25 (2.3 2.9) 44.1 53.9 M10 1.5 Hexagon bolt (7T) (4.5 5.5) and nut 78.4 98.0 M12 1.75 (8.0 10) 127.5 147.1 M14 1.5 (13 15) 215.7 235.4 M16 1.5 (22 24) 9.8 1/8 (1.0) 19.6 1/4 (2.0) PT plug 29.4 3/8 (3.0) 58.8 1/2 (6.0) 12.7 16.7 M8 (1.3 1.7) 19.6 25.4 M10 (2.0 2.6) 24.5 34.3 Pipe joint bolt M12 (2.5 3.5) 39.2 49.0 M14 (4.0 5.0) 49.0 58.8 M16 (5.0 6.0) Note) Lubricating oil is not applied to threaded portion and seat surface. Item Nominal thread diameter pitch Remarks Use 80% of the value at left when the tightening part is aluminum. Use 60% of the value at left for 4T bolts and lock nuts.
197
SERVICE MANUAL
FUEL INJECTION EQUIPMENT

MODEL
YPD-MP2/YPD-MP4
SERIES
Introduction
This document describes the features, disassembly, reassembly and adjustment procedure of the fuel injection unit (Model YPD-MP2,MP4) for Diesel Engine Model TNV. Fuel injection unit is an essential mechanism of diesel engines, and thus, has to be designed to allow fine adjustment to the engine load. Therefore, the components of the fuel injection pumps are required to be given high-precision. To meet this requirement, we process and assemble them very accurately. Accordingly, when performing disassembly and adjustment works in the market, keep the workbenches and their environment clean to surely prevent dirt and dust from attaching to the components of the unit, and take special care that the components are not rusted. Please note that the specifications of the components are revised to improve the quality of the product, and thus, the details of the changed specifications will be notified through the correction table every time the change occurs.
Contents
1. 1.1. 1.2. 2. 2.1. 2.2. 2.3. 2.4. FOR SAFE SERVICING 1 Warning Symbols 1 Safety Precautions 2 GENERAL INFORMATION 4 Outline of MP pump 4 Specifications 5 Outline of fuel injection pump 6 Construction of MP-Pump 7 Fuel Injection Part 7 Governor Part 8 Delivery Part 17
2.4.1. 2.4.2. 2.4.3. 2.5.
Function of Component 18 F.O. Feed Pump 18
2.5.1. 2.6.
Timer Mechanism 20 Structure and Functions 20
2.6.1. 2.7.
C.S.D.(Cold Start Device) 21 Cold Starting Advancer 21
2.7.1. 3. 3.1.
DISASSEMBLY ,REASSEMBLY AND INSPECTION 22 Disassembly 22 Separating the pump body from the governor body 22 Separating the governor weight CMP 23 Disassembling the hydraulic head 23 Separating hydraulic head CMP 25 Separating the cam shaft 25 Disassembling the hydraulic head CMP 27
3.1.1. 3.1.2. 3.1.3. 3.1.4. 3.1.5. 3.1.6. 3.2. 3.3.
Disassembling the Governor 28 Reassembly 29 Re-assembling the hydraulic head 29 ii
3.3.1.
3.3.2. 3.3.3. 3.3.4. 3.4. 3.5. 4. 4.1. 4.2.
Re-assembling Cam Shaft 30 Install the hydraulic head CMP. 34 Assembling the Hydraulic Head 35
Re-assembling the Governor 39 Combining Governor and Pump Bodies 40 ADJUSTMENT OF FUEL INJECTION PUMP AND GOVERNOR 42 Preparations 42 Bottom clearance adjustment(Fuel Injection Timing) 44 The bottom clearance adjusting value and the Cam classification 45
4.2.1. 4.3.
Adjustment of Governor 46 Adjustment of No Load Max. Engine Speed 46 Adjustment of Fuel Limit Bolt 46 Adjustment of Torque-Rise Point 46 Adjustment of Reverse Angleich 47 Adjustment of Staring Injection Amount 48 Checking the Injection Stop 48
4.3.1. 4.3.2. 4.3.3. 4.3.4. 4.3.5. 4.3.6. 5. 5.1. 5.2. 5.3. 5.4.
FUEL INJECTION NOZZLE 49 Functioning of fuel injection nozzle 49 Type/construction of fuel injection nozzle 49 Fuel injection nozzle disassembly 50 Fuel injection nozzle inspection 51 Washing 51 Nozzle inspection 52
5.4.1. 5.4.2. 5.5. 5.6.
Fuel injection nozzle reassembly 53 Adjusting fuel injection nozzle 53 Adjusting opening pressure 53 Injection test 54
5.6.1. 5.6.2. 6. 6.1.
TROUBLESHOOTING 55 Troubleshooting of fuel injection pump 55 iii
6.2. 7. 7.1. 7.2. 8.
Major faults and troubleshooting 55 TIGHTENING TORQUES FOR MAIN BOLTS AND NUTS 58 Pump part 58 Mechanical governor part 59 TOOLS 60
iv
1. For Safe Servicing

! Most accidents are caused by negligence of basic safety rules and precautions. For accident prevention, it is important to avoid such causes before development to accidents. Please read this manual carefully before starting repair or maintenance to fully understand safety precautions and appropriate inspection and maintenance procedures. Attempting at a repair or maintenance job without sufficient knowledge may cause an unexpected accident. ! It is impossible to cover every possible danger in repair or maintenance in the manual. Sufficient consideration for safety is required in addition to the matters marked CAUTION. Especially for safety precautions in a repair or maintenance job not described in this manual, receive instructions from a knowledgeable leader.
1.1. Warning Symbols

! Safety marks used in this manual and their meanings are as follows:
DANGER indicates an imminently hazardous situation, which if not avoided, WILL result in death or serious injury.
WARNING indicates a potentially hazardous situation, which if not avoided, COULD result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury.
Any matter marked [NOTICE] in this manual is especially important in servicing. If not observed, the product performance and quality may not be guaranteed.
1.2. Safety Precautions

! Place allowing sufficient ventilation Jobs such as engine running part welding and polishing the paint with sandpaper should be done in a well-ventilated place Failure to Observe Very dangerous for human body due to the possibility of inhaling poisonous gas or dust
! Sufficient wide and flat place The floor space of the service shop for inspection and maintenance should be sufficiently wide and flat without any holes. Failure to observe An accident such as a violent fall may be caused.
! Cleanorderly arranged place No dustmud0il or parts should be left on the floor surface. Failure to Observe An unexpected accident may be caused
! Brightsafety illuminated place The working place should be illuminated sufficiently and safetyFor a job in a dark place where it is difficult to seeuse a portable safety lamp. The bulb should be covered with a wire cage for protection. Failure to observe The bulb may be broken accidentally causing ignition of leaking oil.
! Place equipped with a fire extinguisher Keep a first aid kit and fire extinguisher c1ose at hand in preparation for fire emergencies
! Wears for safe operation Wear a helmetworking clothes safety shoes and other safety protectors suited to the job. It is especially important to wear well-fiting work clothes. Failure to observe A serious accident such as trapping by a machine may occur.
! Use of appropriate tools Use tools appropriate for the jobs to be done. Use a correctly sized tool for loosening or tightening a machine part. Failure to observe A serious injury or engine damage may occur.
! Always use genuine parts Jobs such as engine running part welding and polishing the paint with sandpaper should be done in a well-ventilated place Failure to Observe Shortening of MP pump unit life or an unexpected accident may arise.
! Always tighten to the specified torque if designated in the manual. Failure to Observe Loosening or falling may cause parts damage or injury.
Observe the following instructions with regard to waste disposal. Negligence of each instruction will cause environmental pollution. ! Waste fluids such as engine oil and cooling water shall be discharged into a container without spillage onto the ground ! Do not let waste fluids be discharged into the seweragea river or the sea. ! Harmful wastes such as oil, fuel, solvents, filter elements and battery shall be treated according to the respective laws and
regulations. Ask a qualified collecting company for example.
2. General information
2.1. Outline of MP pump
MP pump is a fuel injection pump that has been newly developed to be installed on direct injection system diesel engines for the purpose of complying with the regulation for the exhaust gas emission that are becoming tighter in the future. The fuel injection pump is a fuel distribution type pump that supplies fuel to each cylinder of the engine through a distribution shaft by using a single plunger unlike conventional rail system or distribution system pumps.
! Pump name plate
Fuel Injection Pump Asy. code FIE ASY code
ID codePump for Exh.gas Injection No. regulation
ID code for production
Serial numbers
2.2. Specifications
Model
Applicable Engine Plunger Diameter (mm) Max. Cam Lift (mm) Governor-System Fuel Injection Timing Control System Fuel feed pump Lubrication system Dry Weight (kg) 8.4 YPD-3MP2 3TNV82A /84(T)/88 9mm 8.1mm Mechanical All Speed Governor Built-in Hydraulic Control Timer Forced Lubrication System With Trochoid Pump Engine System Oil 8.6 11.5 YPD-4MP2 4TNV84(T) /88 YPD-4MP4 4TNV94 /98(T)/106(T) 10mm 10mm
2.3. Outline of fuel injection pump

Distribution type fuel injection pump YPD-MP consists of a hydraulic head that is equipped with a single plunger, a single distribution shaft, and delivery valves for each individual cylinders, a pump housing that includes camshafts, and a governor, all of which are integrated into the main unit of the pump. For the feed of the fuel, the plunger moves up / down and the distribution shaft rotates with the revolution of the camshaft to distribute the fuel among the cylinders individually. Specifically, one revolution of camshaft completes three cycles (for three cylinder engine) of a process, including switching over to the high pressure flow path to each cylinder with the distribution shaft, opening delivery valve, high pressure pipe, fuel injection valve, and engine cylinders in this order. This process is repeated by the revolution of the camshaft.
< The Flow of the Fuel >
orifice
Fuel injection pipe

Fuel filter
Injection pump
Timer piston Plunger Thermo-element Engine coolant Accumulator
Nozzle
Electric fuel feed pump Water separator
Distributor shaft
12/48
joint Fuel return tappet
Overflow orifice
High pressure gallery Fuel tank Cam

Oil seal
Engine crankcase
Engine oil
Torochoid pump Low pressure gallery

Pressure control valve
2.4. Construction of MP-Pump

2.4.1. Fuel Injection Part
Plug (C.W.) Plug (barrel) Holder (delivery) Delivery valve CMP. Holder (timer) Sleeve (distribution shaft) Piston (timer) Plug (distribution shaft) Joint (C.W.) Thermo element.
Distribution shaft Joint (distribution shaft) Removal stop (Transmission shaft) Transmission shaft
Hydrauric head Packing (timer) Barrel (plunger) Plunger Sleeve (control) Spring (plunger) Tappet (roller) Retainer (spring) Roller Camshaft Flange Drive gear A Drive gear B Accumulator Joint (FO inlet) Joint (overflow)
Spring (accumulator) Plug(accumurator)
Strainer (A)
Strainer (B) F. O. feed pump CMP Control rack Whirl-stop (tappet)
2.4.2. Governor Part

2.4.2.1. Construction of Governor
Usage condition of diesel engines are extremely variedwith a wide range of loads and speedsThe governor plays an important role in the operation of the engine by quickly adjusting the position of the control rack to control the amount of fuel injected, according to changes of engine speed. It also automatically controls the engine to prevent engine speed from exceeding the maximum ,and keeps the engine from stopping. ! Mechanical governor
Shaft (Control lever)
Fuel limiter CMP. Torque spring
Control lever
Spring (governor)
Link Regulator lever Stop solenoid
Shaft (Governor lever) Camshaft Governor case cover Governor Angleich spring assembly Governor lever CMP Sleeve (governor) weight
The governor weight mounted on the end of the fuel injection pump cam shaft rotates around the governor support pin, driven by the cam shaft, and is forced outwards by the centrifugal force acting on the weight The thrust force acting on the cam shaft due to this centrifugal force acts on the lower part of the tension lever through the sleeve A starting excess fuel spring is mounted on the bottom of the tension lever 0ne end of the governor spring is hooked to the right upper end of the tension lever, and the other end to the spring lever of the control lever shaft.
As the spring lever and control lever are mounted on the same shaft, when the control lever is turned towards full, the governor spring is pulled and the load gradually increases. Since the tension lever can move freely around the governor shaft on the player bearing, as speed increases and the shifter is pushed to the leftthe tension lever rotates clockwise, and when speed decreasesthe tension lever rotates counterclockwise. The governor lever rotates smoothly on the second shaft installed on the tension leveb. The bottom part of this lever is in contact with the sleeve through the shifter, which is in contact with the bottom of the tension lever through the excess fuel spring. It therefore moves with the tension lever according to increasesdecreases in engine speed. The top of the governor lever is connected to the fuel pump control rack through the governor link. The movement of the lever controls the volume of fuel injected by the pump. When speed increases the lever rotates clockwise to cause the control rack to reduce fuel and when speed decreases the lever rotates counterclockwise to cause the control rack to increase fuel, thus engine speed is controlled. The top of the tension lever comes in contact with the stopper built into the top of the governor case to limit the maximum fuel injection volume.
(1) Shape of control and stop levers The control and stop levers that operate the governor have different shapes depending on engine design and method of attachment, as seen in the pictures below. The motion of the control lever is regulated by the maximum speed adjustment bolt and the idling adjustment bolt. This maintains the necessary engine speed.
(2) Engine stop device The magnetic solenoid is equipped to stop the engine.
Injection volume Decrease

Link Stop solenoid
(3)Torque rise equipment As mentioned beforethis governor has a structure that allows you to equip it with an anglich and/or torque spring as torque rise equipment. In this way the requirements for different engines can full filled.
Torque spring CMP
Angleich spring CMP
10
2.4.2.2. Function of Governor (1) Function of governor Following is a representation of the movement characteristics of the control rack at respective speedswhen the speed rise from 0,with the governor control lever at the maximum speed position:
A-B : Fuel volume condition during starting. Volume is controlled by excess fuel spring. B-C : The rack moves towards decrease after engine starts and speed increase as the load of the excess fuel spring is overcome by the centrifugal force of the governor weight. C-D : High torque at low speed is developed by increasing fuel injection volume equivalent to the angleich stroke. D-E : Condition when the thrust force exceeds that of the angleich spring force on the bottom of the tension lever and it gradually pushes the rack to decrease fuel when engine speed increases. E-F : Condition when both right and left ends of the shifter come in contact with the sleeve and the bottom of the tension lever, and the control rack is kept at the normal position by the stopper.maxinjection volume position on models not equipped with an angleich spring) F : Point when governor starts to take effect. This is the rated output of the engine F : Point when governor start to take effect on models with torque spring G : Continuous rating pointusually 8590 injection volume of F point). H : No load maxspeed L : Low-idle position
11
(2) Starting control Moving the control lever to the max speed position pulls the governor spring, and moves the tension lever until it comes in contact with the control stopper. When this is donethe excess fuel spring provided in between the tension lever and governor lever holds the control rack at the maximum starting injection volume position RA-B. After the engine is started, the excess fuel spring is compressed when the centrifugal force of the governor weight overcomes the set of the excess fuel spring as speed exceeds Nb, speed goes from B to C' (on models with angleich spring ) or B to C(on models without angleich spring ). The rack reaches the position of Rc where the governor lever and tension lever are interlocked.
3 Idling When the control lever is returned to the idling position after the engine is started. the governor spring tension decreases and the tension lever descends clockwise, and the governor weight load keeps the governor spring and the excess fuel spring load in equilibrium to maintain idling speed at (RL).
12
(4) Max speed The angle of the control lever is set at determined engine speed. The governor keeps engine speed constant by adjusting sped when load changes. For example, if the operator moves the control lever with the link from the idling position to max. Output, governor spring tension increases, the tension lever is pulled until it comes in contact with the full load stopper, the movement of the governor lever is transmitted to the control rack via the link, maintaining the full load rack position, and engine sped increase until the governor weight thrust load and governor spring tension come into equilibrium at full load max. Speed.
(5) Necessity and function of angleich The governor must satisfy the required injection curves represented in the diagram below in order to obtain sufficient output at low speed, and not emit black smoke at high speed. the angleich spring was devised to provide for maximum torque at low sped by setting injection volume at point A, and shifting injection volume to point B' at high engine speed.
13
The angleich spring is mounted to the part of the tension lever (however some engine are not equipped with an angleich spring depending on usage and speed range utilized). When engine speed is low, the governor weight cannot compress the angleich spring as the angleich spring load is lager than the governor weight, thrust load, and the control rack is held at a position (Rc) to increase injection volume. Furthermore, as engine speed rise, the angleich spring is gradually compressed as governor weight thrust load increases and exceeds angleich load, before high speed control is effected. When the governor lever and the bottom of the tension lever come into contact (end of angleich stroke), injection volume is reduced by that amount, and the rack reaches the rated position (RE).
14
(6) Necessity of torque spring and function Engines used in construction machinery are subjected to sudden loads which cause a decrease in speed and sometimes results in stopping of the engine. A torque spring is provided to move the control rack towards injection volume increase when engine speed decrease to increase torque to withstand overloads, and in turn prevent the engine from stopping. The governor control lever is fixed at point G in the diagram below, the continuous rated output position. At this timewhen engine is loaded, the tension lever encompasses the torque spring, the control rack comes away from full load stopper, and fluctuates between G and H according to engine load. When the load on the engine exceeds the continuous rated output, speed decrease, governor spring tension exceeds the governor weight thrust load and overcomes the torque spring set load. The tension lever then gradually causes the control rack to move towards injection volume increase via the governor lever and link, and the torque rise stroke ends when the control rack reaches F'.
The torque spring thus provides for increasing of injection volume when speed decrease, to increase engine torque and in turn prevent engine stopping due to sudden increases in load, and also provide for strong engine output characteristics.
15
(7) No load max. speed When the load decreases from full load max. speed and engine speed further increase, the increased thrust load of the governor weight acting on the governor spring through the tension lever exceeds the set load of the spring, the tension lever and governor lever descend clockwise, the control rack is pushed to the no load injection volume position (RH), and the engine is operated at no load max. Speed. When the engine is being used at partial load, the governor spring functions in the same way at a lower speed (i, i'-j) as for full load max. Speed, as the governor spring set load is smaller.
(8) Stopping engine The engine stops when you turn the governor control lever all the way towards stop. On engine equipped with a stop device, the engine can be stopped by moving the control rack to the stop position, regardless of the control lever position.
16
2.4.3. Delivery Part

Delivery Ports and Cylinder Number
4MP2, 4MP4 Cylinder No. B A Port No. 2 1 Injection Order C 3 D 4
Flywheel side
Driving side
3MP2 1 Cylinder No. B Port No. 2 Injection Order
2 A 1
3 C 3
Flywheel side 1 2 3
Driving side
17
2.5. Function of Component

2.5.1. F.O. Feed Pump
The FO feed pump feeds fuel oil from the fuel tank to the fuel injection pump via the water separator and fuel filter. The trochoid FO feed pump, installed on the fuel injection pump side, is driven by the fuel camshaft via the bevel gear. This feed pump can feed high pressure fuel oil into the FO injection pump, but while the fuel oil inside the piping is empty due to shortage of gases, etc., the pumps self-feeding performance is low. Accordingly, the manual priming pump with FO filter or solenoid pre-feed pump is used together. The feed pump failure causes the delivery pressure and volume to drop. This, in turn, shortens the service life of the fuel injection pump and causes the pump to become faulty. Replace the feed pump assembly after 10,000 hours use as a standard.
FO feed pump
Pump case Pump cover Inner rotor Outer rotor Shaft Molded ring Oil seal Bevel gear
Drive pin Relief valve Spring Seal washer Relief plug Bolt C-ring Bush Thrust washer Washer
18
2.5.1.1. Specifications of F.O. Feed Pump
YPD-MP2
YPD-MP4
Suction Head P Std. Delivery Pressure MP Std. Delivery Volume cm3/min
-10 0.4-0.5 500 0.6-0.7 600
Pressure & delivery volume figures at conditions below: Conditions:
Outlet orifice dia. :0.7mm F.O. grade : ISO 8217 Revolutions : 1000min F.O. temp. : 40 degC (104 degF)
2.5.1.2. Inspection of F.O. Feed Pump

(1) Check for the abnormal flaws and chipping on the bevel gear face. assembly. (2) Check for the abnormal flaws or wear on the face contacting with the pump case, pump cover, inner rotor and outer rotor. If wear exceeds 0.1mm, replace the whole feed pump assembly. (3) Check for the abnormal wear of the shaft and oil seal moving area. feed pump assembly. (4) When no abnormality was found, just replace the molded ring and seal washer and re-assemble. (5) After install the fuel injection pump, operate the fuel injection pump to check that no oil leaks from each part. If wear exceeds 0.05mm in depth, replace the whole If found to be abnormal, replace the whole feed pump
19
2.6. Timer Mechanism

When the engine is used in a wide range from low to high speeds, it is necessary to change the fuel injection timing according to the engine speeds for always keeping the optimum firing timing. It is also necessary to optimize the injection timing for reducing noise and exhaust gas emissions. This pump has the timer mechanism for revolutions, load and cold starting.
2.6.1. Structure and Functions

The engine speed timer is the mechanical timer which uses the oil leakage from the small diameter sub spill port installed slightly upper side of the main spill port of the jerk pump. When the engine speed is high, pressure rises before oil leaks from the small diameter port and injection is started. But when the engine speed is low, pressure does not rise until the port blocked by the plunger and the injection start is delays. Usually, the lower the engine speed, further the injection timing advances. But this engine speed timer prevents the injection timing from advancing during the low engine speed ranges and thus the noise and Nox. emissions can be controlled. The fewer the injection amount, the earlier the load timer causes the main port to close by the plungers upper lead for advancing the injection timing. This feature is instrumental in preventing misfire or emission of bluish white smoke during low load operation. The cold start timer causes the sub port to be blocked only under cold temperatures for accelerating injection timing and facilitating in cold starting. The timer houses the thermo element and cooling water circulates around the temperature sensing section. The thermo-element senses the coolant temperature for adjusting the control piston. The sub-port is blocked when the temperature is lower than the set temperature and the pressure is raised earlier than in the normal temperature for advancing the injection timing. When the temperature exceeds the set temperature, the sub-port is opened and the regular injection characteristics are recovered.
Hydraulic control device of injection timing (Speed timer,Load timer,Cold start timer)
Advance
Timing Control Device
Required characteristics
A :Sub Port B : Sub Lead Main Port Main Lead
Coolant C : Thermo -element
Injection Timing
Improving cold startability At cold start At no load
Piston
Rated At full load Reduction of noise & NOx Reduction of white smoke
Barrel Plunger
Retard
Pump speed
20
2.7. C.S.D.(Cold Start Device)

2.7.1. Cold Starting Advancer
Purpose In order to facilitate easy engine starting under cold temperatures, the advancer senses the cooling water temperature for advancing the fuel injection timing.
2.7.1.1. Structure & Function
At normal operating Termo-elementt

Sub-port is opened Main port Sub port
Engine coolant
At cold starting
Sub-port is closed
Piston Fuel IN
Fuel IN
Spring Plunger Fuel gallery Plunger barrel When the coolant temperature is higher than specified value, the thermo-element keeps expanding and the subport is opened. When the coolant temperature is lower than specified value, the thermo-element keeps shrinking and the subport is closed by piston.
21
3. Disassembly ,Reassembly and Inspection

3.1. Disassembly
Disassembled parts must be put aside in order. Wash them before reassembly.
3.1.1. Separating the pump body from the governor body

Rotating the link lifter will move the inside link upward/downward, so the control rack may be engaged/disengaged.
Install the pump body to the disassembly table.

Remove the bolt fixing the pump and governor bodies.
Remove the link lifter fix bolt.
Separate the governor from the pump body.
Link insertion window
Turn the link lifter plate counterclockwise. The pump body separated from t he governor body
22
3.1.2. Separating the governor weight CMP
Disassembling the delivery valve
Remove the holder, (delivery). Providing whirl-stop to the camshaft
Remove the delivery valve and gasket.
Example of whirl-stop
Remove the nut, (governor support).
Delivery valve parts disassembled. (Take care not 3.1.3. Disassembling the hydraulic head
Disassembling the hydraulic head
to mix these with other parts on reassembly. Reassemble these to the original port as a set.)
Remove the joint, (FO inlet pipe).
Remove the delivery valve and gasket. Remove gasket 23
Remove the distribution shaft. Removed parts must be stored in the cleaning oil sump.
Remove the holder and gasket, (timer)
Remove the plug, (accumulator). Remove the plug and gasket, (barrel). Make sure that the seal washer remains on the plug.
Remove the plug, (C.W.) and the joint, (C.W.)
Parts disassembled.
Remove the thermo element.
24
3.1.4. Separating hydraulic head CMP
3.1.5. Separating the cam shaft
Remove the joint, (distribution shaft).
Remove the hydraulic head CMP fixing bolt.
Remove the feed pump. Do not loosen two bolts (A) . Remove the hydraulic head CMP.
O-ring Make sure that two O-rings are free from damages. Remove the packing.
Remove the removal stop, (transmission shaft) fastening bolt.
25
Lift the transmission shaft slightly by your hand. Remove the whirl-stop, (tappet).
Align the camshafts key groove with the embossed mark on Take out the tappet. the body.
Tappet disassembled and FIC adjust shim.
Lift the transmission shaft a little and pull out the camshaft.
Remove the retainer, (bearing) fastening bolt. Camshaft extracted
Remove the retainer, (bearing). Remove the transmission shaft CMP.
26
Remove the transmission shaft CMP.
3.1.6. Disassembling the hydraulic head CMP

Remove the rack guide.
Remove the spring retainer. Compress the plunger spring and remove the spring retainer, (B). While compressing the plunger spring using special service tool, remove spring retainer B. Spring retainer B. Plunger SP seat extractor Remove the control sleeve. Hydraulic head
Cleaning oil sump
Remove the plunger.
Cleaning oil sump
Remove the rack return spring.
Parts removed from hydraulic head CMP Disassembled parts must be separately stored in the cleaning oil sump. Remove the rack guide fastening bolt. 27
3.2. Disassembling the Governor
Removed governor lever shaft Remove the lock nut, (Control lever).
Remove the regulator lever.
Take out the governor lever CMP.
Remove the shim. Remove the spring.
Remove the removal stop, (governor lever shaft) fixing bolt.
Remove the removal stop, (governor lever shaft).
Pull out the governor lever shaft.
28
3.3. Reassembly
3.3.1. Re-assembling the hydraulic head
Install the rack guide. Rack guide Control sleeve Rack auxiliary SP Rack
Install the plunger.

Upper lead
L
Sub-lead Ball Identification marking
Upper spring retainer Distribution shaft sleeve Attaching rack and rack guide
! Note that the positional relationship of the upper lead and sub-lead of the plunger and the ball of the control sleeve is as shown below. (Plunger identification marking (such as "W4") and the ball of the control sleeve are oriented in the same direction.) ! Be careful that the plunger is NOT inserted upside down.
! When installing rack guide, push it against the distribution shaft sleeve and upper spring retainer so that the rack is in parallel with the direction of camshaft. (T = 3 to 4 Nm) ! Movable range of rack is to be equal to or larger than 7 mm. ! Fix the rack at the position of L = 25, and measure the effective stroke and sub-step (overflow stroke) to check that they are within the standards (Refer to attached drawing 1.) ! The rack must not separate from the ball of the control sleeve within the movable range. ! Fix the plunger with a jig and measure the total backlash. (To be equal to or less than 0.2 mm) ! The load of rack auxiliary SP must be able to return the rack from the maximum decreased position to the maximum increased position).
Install the control sleeve and spring retainer.
29
3.3.2. Re-assembling Cam Shaft
Install the rack guide fastening bolt. Tightening Torque : 3.9-4.9 N-m Install the transmission shaft CMP.
Spring retainer (B). Spring.
Install the plunger spring and spring retainer (B). Attaching transmission shaft CMP ! Apply molybdenum disulfide to the shaft section. ! Check that the transmission shaft rotates
Install the camshaft.
30
Install the camshaft.

Attaching camshaft ! Apply molybdenum disulfide to the bushing or the bearing. ! Insert the camshaft into the pump body with transmission shaft CMP at the lowered position (gear B touching the pump body). ! Be careful that the cam and gear B do not interfere with each other. ! (Especially for 4 cylinder engine, note that the phase in which the cam passes is limited.) ! The shaft can be inserted with the key of the driving side press-fitted to the camshaft. Be careful not to damage the camshaft bushing. Checking backlash ! Rotate camshaft to check that transmission shaft rotates smoothly. ! Fix transmission shaft from upper surface of the housing, and turn the camshaft to check the backlash. Backlash must be in the range from 0.2 to 1.5 degree. Note: When measuring at the position of camshaft driving side key (at the center of the key as shown below), the displacement must be in the range from 0.03 to 0.25. Tightening Torque : 8-10 N-m
Rack plug Tighten the rack plug. (If rack plug has been removed.) Tightening Torque : 79-84 N-m
Position the transmission shoe of the transmission shaft CMP as shown in the illustration.
31
Position the camshaft key groove as shown in the illustration.

Engagement of gears With the phase of camshaft and collar of transmission shaft set in the direction as shown below, engage gears A and B with each other. (Check that the match mark of gear B and the mark of gear A shown below are aligned with each other by looking through the feed pump installation hole.) When inserting the stopper pin, do not raise the transmission shaft excessively, or the gears will be disengaged. (Check the engagement again after inserting the stopper pin.) The positions of the collars of transmission shaft are not limited only if either one is at the top or bottom as shown.
Install the removal stop, (transmission shaft). Fasten the removal stop, (transmission shaft). Tightening Torque : 8-10 N-m 32
Whirl-stop groove
Fasten the nut, (governor support), (and provide the whirl-stop to the cam shaft.) Install the tappet. Direct the tappets whirl-stop groove as shown in the illustration. Assembling tappets ! Insert tappet into the pump body with the slit directed toward the lock side, and attach the tappet lock. (T = 4 to 5 Nm) ! Turn the camshaft to check that the tappet moves up and down smoothly. Tightening Torque : 79 - 84 N-m
Install the feed pump.
Identification hole (3, depth 2 mm) Install the whirl-stop, (tappet). Tighten the tappet, while moving it upward and downward. Identification of feed pump
Spec. General purpose TK 3 identification hole Not provided Provided
Note that the identification hole can be seen only when looking from obliquely above because it is located on the pump case side. Install the governor weight CMP and nut, (governor support). 33
3.3.3.
Install the hydraulic head CMP.
Install the hydraulic head CMP. Insert the two positioning pins. packing front with rear surface. on the body.) Be sure not to confuse (Align them with holes Installing H head ! Assemble shims with an appropriate thickness that corresponds to the measurement of the bottom clearance (refer to attached drawing 3). ! Temporarily tighten the hexagon socket head bolts evenly in the order as shown below until the surfaces of H head and pump body contact with each other, and Install the joint, (transmission shaft). subsequently tighten to the specified torque in the same order. ! After assembling H head, check the top clearance again. ! After assembling H head, push the rack from governor side to check that the rack is returned with the force of rack auxiliary SP. ! When reassembling H head, be sure to replace the Assemble the FIC adjust shim inside the tappet. head packing with new one.
Install the hydraulic head CMP.

While hand pressing the hydraulic head, temporarily tighten the tightening bolts. with specified torque. 34 Then, tighten them
Install the hydraulic head CMP fastening bolt. Important Tightening Torque : 18-22 N-m
Tighten the bolts in diagonal order, while checking the torque with torque meter.
Install the distribution shaft. Inserting distribution shaft Insert distribution shaft so that the directional relationship between the shaft and camshaft is as shown below (Do not assemble upside down). Use the following drawing simply as a reference because the component can be inserted in either of two orientations. Insert the component securely into the distribution shaft joint until it is sunk below the end surface of the distribution shaft sleeve.
Measure the plunger top position. Bottle clearance adjustment should refer to Page 59.
3.3.4. Assembling the Hydraulic Head
Direction of fixed flange (camshaft keyway) (As viewed from driving side)
Install the accumulator.
Camshaft keyway Operating side
Upper side Anti-operating side Lower side
Attaching accumulator
! Be sure to install the piston in the correct direction. ! Make sure that the piston can slide smoothly.
Flange cutout
Direction of distribution shaft longitudinal groove (As viewed from upper side Distribution shaft longitudinal groove, cut off surface Install the spring, (accumulator). Operating side Governor side Anti-operating side
Driving side
Install the plug with new seal washer, (accumulator). 35
Install the plug, (distribution shaft).
Install the new packing, (delivery valve seat).
Fasten the plug, (distribution shaft). Tightening Torque : 10-15 N-m
Install the delivery valve CMP.
Holder(delivery Spring(delivery Valve(delivery Returnvalve Spring seat(return valve Returnspring Seat(delivery Packing(delivery
Install the plug with new copper packing, (barrel).
Install the spring, (delivery).
Fasten the plug, (barrel). Tightening Torque : 30-35 N-m
Install the holder, (delivery). Tightening Torque : 40-45 N-m 36
Install the new packing, (timer).
Fasten the holder, (timer).
Install the thermo-element with new O-ring.

Install the holder with new O-ring, (timer).
C.W.plug Thermo-element Seal washer O-ring P14 Piston(thermo-e lement) O-ring(JASO 1020) Spring O-ring P15 (Hardness 90 Timer holder O-ring(JASO 1020) Timer piston Damper ring O-ring JASO 1011 Timer packing
Before installing the thermo-element, press down the piston with the timer holder being installed to the head, (T=40-45N.m), and check that the piston returns up through the spring load. The standard thermo-element release temperature shall be 5-8 degC(41-46.4 degF). (Thermo-element released at 15-18 degC (5964.4 degF) is available as option. Take care not to mistake the specifications: see diagram below.)
Identification groove
* JASO : Japanese Automobile Standard
Thermo-element for 1518 degC Do not forget to assemble the timer packing, (at holder bottom). ! Do not forget to assemble the damper ring. ! Take care not to use O-rings with inappropriate sizes. Check that the timer piston moves smoothly in the timer holder hole (clearance: 4-8 micron m). ! ! Do not pull out the piston housed in the thermo-element manually. If it is extracted manually, discard it since the re-use of the piston is no longer possible. Do not tighten the thermo-element with excessive tightening torque, (T=30-35N.m). Do not tighten t he cooling water plug with excessive tightening torque, (T=22-25N.m). Take care not to catch impurities in the seal washer.
! ! !
37
F.O. valbe return pipe F.O. outlet
Cooling water
Fasten the thermo-element. Tightening Torque : 30-35 N-m
F.O. inlet
Install the joint, (C.W), and he plug, (C.W.)

Assemble the seal washers, taking care not the washer stride over steps. (One seal washer is required for respective upper and lower portions.)
Install the joint, (FO inlet).
Installation position of Joints Direction of pipe depends on respective specifications.
Fasten the plug, (C.W.)
Install the joint, (overflow) and the joint, (overflow).
38
3.4. Re-assembling the Governor
Install the shim to the shaft, (control lever).
Governor Body Parts
Install the regulator lever.
Governor Lever CMP End Float Adjust Shim
Pierce the spring, (control lever) through the lock nut, (control lever) and fasten it to the thread of the shaft, (control lever). Pierce the governor lever CMP and shim through the governor lever shaft and assemble. Measure the side clearance of the tension lever with thickness gauge. Standard: 0.3 to 0.6 mm (adjusting with shim)
Fasten the nut, (control lever). Tightening Torque : 19.6-24.5 N-m
Fit the governor lever shaft with the removal stop, (governor lever shaft) and fasten the removal stop bolt.
Measure the side clearance with thickness gauge. Standard: 0.3 to 0.6 mm (adjusting with shim)
39
3.5. Combining Governor and Pump Bodies
Turn the link lifter plate counterclockwise. and install the governor body to the pump bodies Install the new packing. Do not confuse front with rear surface. Assemble it, while aligning bolt holes with those on the body.
Rack
Link Link lifter a) During assembly b) During operation
Attaching governor CMP Be careful not to bend or damage the governor case packing (GRC). (It is not reusable. If it sticks to the packing surface, remove it without giving damage to the surface of the packing.) Direct the link lifter as shown in Fig. a) shown below, where the semicircular section is positioned at the lower side, and bring governor CMP to the pump body until the link comes into contact with the rack. At this time, be careful that the link does not hit the pump body. (If the link hit the pump body severely, check that the link is not bent or deformed.) Direct the link lifter as shown in Fig. b) shown below, where the semicircular section is positioned at the upper side, and engage the rack and the link with each other. At this time, if it is difficult to engage the rack and the link with each other, assemble them while pushing the governor lever to the decreasing side (when mechanical governor is used). After putting the link lifter in the state shown in Fig. b), pull the governor CMP a little to check that the link and rack are engaged with each other. (Be sure not to pull governor CMP excessively). (If the barrel plug is not installed yet, the following method can be used to check the plunger rotation. Mechanical governor: Push the governor lever to the decreasing side through the solenoid attaching hole. New ECO governor: Push the rack to the increasing side through the rack inspection port.) Be sure to tighten the link lifter securing bolt. (T = 8 to 10 N - m)
40
Install the governor case cover to the case. Insert the governor link into the link hole of the pump body.
This completes reassembly of the pump.

Fit the link lifter to the installation hole and fasten the bolt.
Pull the governor assembly slightly to check that the link is engaging securely. Combine Governor and Pump Bodies
Install the new O-ring to the stop solenoid and assemble them to the governor case. Tightening Torque : 7.8-9.8 N-m
nstall a new packing, (governor case cover) to the case.
41
4. Adjustment of Fuel Injection Pump and Governor

Adjust the fuel injection pump after you have completed reassembly. The pump itself must be readjusted with a special pump tester when you have replaced major parts such as the plunger assembly, roller guide assembly, fuel camshaft, etc. Procure a pump tester like the one illustrated below.
4.1. Preparations
Prepare for adjustment of the fuel injection pump as follows: (1) Adjusting nozzle assembly and inspection of injection starting pressure.
Mpa (kgf/cm2) Adjusting nozzle type Injection starting pressure (2) Adjusting injection pipe. mm Inner dia./outer dia. length Minimum bending radius
2.0/6.0 600 25 YDN-12SD12 16.2 17.2(165 175)
(3) Mount the fuel injection pump on the pump tester platform.
42
(4) Remove the plug in the oil fill hole on the top of the governor case, and fill the pump with about 200cc of pump oil or engine oil.
(5) Complete fuel oil piping and operate the pump tester to purge the line of air. (6) Set the pressure of oil fed from pump tester to injection pump at 19.6-29.4kPa(0.2-0.3kgf/cm2 ) ,temp. at 402 degC(104 3.6 degF)
43
4.2. Bottom clearance adjustment(Fuel Injection Timing)

1. The Fuel Injection Timing of MP-pump is made by means of adjusting the bottom clearance of the Cam ie. adjustment of the Pre-stroke of the plunger , as follows. 2. The adjustment of the clearance shall be made at cam-top position in order to get the reliable the bottoms clearance (of the Cam). 3. First of all , put the JIG of the bottom clearance measurement on the standard gauge(W/A- measurement). Then set the O-point of the dial gauge. 4. Next adjust the clearance by shims into the standard after measuring the bottom clearance A* with JIG (Dial gauge)(Refer to the attached sheet)*Measurement between upper surface of the Barrel and upper surface of the plunger at Cam bottom position and easier method. Therefore herein after we will mention that The adjustment of
Bottom clearance gauge
Dial gauge
Bottom clearance gaug

Barrel
A
Plunger Shim
44
4.2.1. The bottom clearance adjusting value and the Cam classification Cam shaft
Cam speed MP2 1.1 m/s 1.3 m/s 1.7 m/s 1.8 m/s 2.1 m/s 2.3m/s 3 cylinder 158552-51020 158552-51030 158552-51040 4 cylinder 158553-51020 158553-51030 158553-51040 123907-51040 129906-51040 129907-51040
Plunger bottom
Clearance (dimension: A) (mm) 25.50.05 25.90.05 26.30.05
25.550.05
Standard shim thickness (mm)

1.3 0.9 0.8 1.05
MP4
Shape of cam shaft end Cam Speed MP2 1.1m/s MP4 2.3m/s
1.3m/s
2.1m/s
1.7m/s
1.8m/s
45
4.3. Adjustment of Governor

4.3.1. Adjustment of No Load Max. Engine Speed
Set the engine speed at the no load max. speed. injection amount. Pull the regulator lever and adjust the max. speed limit bolt to obtain the specified Fasten the nut after completing the adjustment.
4.3.2. Adjustment of Fuel Limit Bolt

The MP2 pump has the lift adjustment FO limiter as a standard equipment. Screw in the lift adjustment screw fully, then return (In the screw by 0.5 turns and fasten the screw with the lock nut. lift adjustment screw completely free.) Set the pump speed at the rated speed and move the regulator lever until it contacts the maximum speed limit bolt.
the specifications where no torque control spring is used, keep the
Check that the amount being injected exceeds the rated injection
amount, screw in the fuel limit bolt and adjust the injection amount.
4.3.3. Adjustment of Torque-Rise Point

The Torque-Rise adjustment comprises the FO limiter (torque spring) and the torque control spring.
Set the pump speed at the Torque-Rise speed and leave the regulator lever at the position in 2 above.
When both of the FO limiter and torque control spring are used:
!
Adjustable lift torque spring
Screw in the torque control assembly, adjust to obtain the specified injection amount and fasten the lock nut.
Specifications of Only the FO Limiter
Screw in lift limit bolt of the FO limiter, adjust to obtain the specified injection amount and fasten the lock nut.
46
4.3.4. Adjustment of Reverse Angleich

In the case of the governor with reverse angleich mechanism, use the reverse angleich spring in the assembled state.
Adjustment of Reverse Angleich Make adjustment of reverse angleich after completing the following processes: Adjustment of fuel volume limiter bolt Adjustment of no-load max, and min. revolutions limiter bolt Shift the control lever to the full load position, and maintain the fuel injection pump revolution to the specified reverse angleich control revolution number (N6). In this condition, remove the governor rear cover, and screw the reverse angleich assembly into the threaded portion of the tension lever until it hits the reverse angleich lever. If screwing it in additionally, the reverse angleich lever will shift in the direction of fuel reduction. Screw and set it to the position of the specified injection quantity (R6). Tighten the lock nut with specified tightening torque, and attach the governor rear cover. N-m (kgf-m) Lock Nut Tightening Torque 24.5-29.4(2.5-3.0)
Again, increase the revolution of the fuel injection pump to the rated revolution speed (N1), check that the control rack will change the position of the reverse angleich stroke smoothly, and confirm that the rack position (R1) and injection volume are within the specified limits.
47
4.3.5. Adjustment of Staring Injection Amount Set the engine speed at the starting injection amount adjust speed and leave the regulator lever at the position in 2 above. Screw in the starting injection amount adjust bolt and adjust it to obtain the specified injection amount. Set the pump speed at 50 min-1 and check that the amount exceeding the specifications is being injected.
4.3.6. Checking the Injection Stop Leave the regulator lever at the position as before. Checking the Injection Stop: Set the pump speed at the speed 50min-1 higher than the no load max. speed, and check that the injection amount reduces to zero. Checking the Stopping: Set the pump speed at the rated speed, turn off the stop solenoid and check that the injection amount reduces to zero.
48
5. Fuel injection Nozzle

When fuel 0il pumped by the fuel injection pump reaches the injection nozzle it pushes up the nozzle valve held down by spring and is injected into the combustion chamber at high pressure The fuel is atomized by the nozzle to mix uniformly with the air in the combustion chamber. How well the fuel is mixed with high temperature air directly affects combustion efficiencyengine Performance and fuel economy Accordingly, the fuel injection nozzles must be kept in top condition to maintain performance and operating efficiency.
5.1. Functioning of fuel injection nozzle

Fuel from the fuel injection pump passes through the oil port in the nozzle holder and enters the nozzle body reservoir. When oil reaches the specified pressureit pushes up the nozzle valveheld by the nozzle spring and is injected through the small hole on the tip of the nozzle body The nozzle valve is automatically pushed down by the nozzle spring and closed after fuel is injected. Oil that leaks from between the nozzle valve and nozzle body goes from the hole on top of the nozzle spring through the oil leakage fitting and back into the fuel tank. Adjustment of injection starting pressure is effected with the adjusting shims.
5.2. Type/construction of fuel injection nozzle

There are two types of fuel injection nozzles. Direct injection engines are equipped with the hole type, and indirect injection engines with the pintle type. The YPD-MP fuel injection pump is designed for use with both direct and indirect injection engines. The hole type/pintle type of fuel injection nozzle are used according to the engine type.
Nozzle opening pressure
Hole type fuel injection nozzle
Nozzle angle No. of nozzlesdia. Identification No. (Nozzle type)
MPa (kgf/cm2) deg. mm
21.6
+1.0 0 162 50.16
(220)
(+10) (0) 159 50.17
162P165VAE1
159P175VAD1
F.O. return pipe joint
Nozzle holder
Nozzle spring
Nozzle spring seat
49
Nozzle body identification number The type of nozzle can be determined from the number inscribed on the outside of the nozzle body. 1Hole type fuel injection nozzles
5.3. Fuel injection nozzle disassembly

Note: 1. Disassemble fuel injection nozzle in a clean area as for fuel injection pump. 2. When disassembling more than one fuel injection nozzle, keep the parts for each injection nozzle separate for each cylinder (i.e. the nozzle for cylinder 1 must be remounted in cylinder 1). (1) When removing the injection nozzle from the cylinder head, remove the high pressure fuel pipe, fuel leakage pipe, etc., the injection nozzle retainer nutand then the fuel injection nozzle.
(2) Put the nozzle in a vise NOTE: Use the special nozzle holder for the hole type injection nozzle so that the high pressure mounting threads are not damaged. 50
3Remove the nozzle nut
NOTE: Use a special box spanner for the hole type (the thickness of the two nozzle nuts is 15mm(0.5906in.)). (4) Remove the inner parts NOTE: Be careful not to loosen the spring seat, adjusting shims or other small parts.
5.4. Fuel injection nozzle inspection

5.4.1. Washing
1Make sure to use new diesel oil to wash the fuel injection nozzle parts. 2Wash the nozzle in clean diesel 0il with the nozzle cleaning kit.
(3) Clean off the carbon on the outside of the nozzle body with a brass brush. (4) Clean the nozzle seat with cleaning spray. (5)Clean off the carbon on the tip of nozzle with a piece of wood.
51
5.4.2. Nozzle inspection

1Inspect for scratches/wear lnspect oil seals for abnormal scratches or wear and replace nozzle if the nozzle sliding surface or seat are scratched or abnormally worn. (2Check nozzIe sliding Wash the nozzle and nozzle body in clean diesel oiland make sure that when the nozzle is pulled out about half way from the bodyit slides down by itself when released. Rotate the nozzle a littlereplace nozzle/nozzle body as a set if there are some places where it does not slide smoothly.
3) Inspecting stop plateinter-piece Check for scratches/wear in seals on both ends, check for abnormal wear on the surface where it comes in contact with the nozzlereplace if stop plate is excessively worn.
4lnspecting nozzle spring Replace the nozzle spring if it is extremely bentor surface is scratched or rusted
5Nozzle holder Check oil seal surface for scratches/wearreplace if wear is excessive. 52
5.5. Fuel injection nozzle reassembly

The fuel injection nozzle is reassembled in the opposite order to disassembly.
(1) Insert the adjusting shims, nozzle spring and nozzle spring seat in the nozzIe holdermount the stop plate with the pin
i nsert the nozzle body/nozzle set and tighten the nut.

(2) Use the special holder when tightening the nut for the hole type nozzle as in disassembly.
Nozzle nut tightening torque Hole type nozzle N-m(kgf-m) 39 44 ( 4 5 )
5.6. Adjusting fuel injection nozzle

5.6.1. Adjusting opening pressure
Mount the fuel injection nozzle on the nozzle tester and use the handle to measure injection starting pressure. If it is not at specified pressure, use the adjusting shims to increase/decrease pressureboth hole and pintle types). Ajusting by 0.1 mm results in a change in the injection starting pressure of about 2 Mpa ( 20 kgf / cm2 ) Injection starting pressure MPa(kgf/cm2) 19.6 - 20.6 ( 200 210 ) 21.6 22.6 ( 220 230 )
Injection starting pressure
Remark ) Injection starting pressure changes on enjine specifications.
53
5.6.2. Injection test

After adjusting the nozzIe to the specified starting pressure, check the fuel spray condition and (1) Check seat oil tightness After two or three injections, gradually increase the pressure up to1.96MPa (20kg/cm2before reading the starting pressure maintain the pressure for 5seconds, and make sure that no oil is dripping from the tip of the nozzle. Test the injection with a nozzle testerretighten and test again if there is excessive oil leakage from the overflow coupling. Replace the nozzle as set if oil leakage is still excessive. 2injection spray condition Operate the nozzle tester lever once to twice a second and check for abnormal injection. seat oil tightness.
5.6.2.1. Hole type nozzles

Replace hole type nozzles that do not satisfy the following conditions Proper spray ang1e Correct injection angle Complete atomization of fuel Prompt starting /stopping of injection
54
6. Troubleshooting
6.1. Troubleshooting of fuel injection pump
Complete repair means not only replacing defective parts, but finding and eliminating the cause of the trouble as well. The cause of the trouble may not necessarily be in the pump itself, but may be in the engine or the fuel system. If the pump is removed prematurely, the true cause of the trouble may never be known. Before removing the pump from the engine, at least go through the basic check points given here. Basic checkpoints
! ! ! ! Check for breaks or oil leaks throughout the fuel system, from the fuel tank to the nozzle. Check the injection timings for all cylinders. Are they correctly adjusted? Are they too fast or too slow? Check the nozzle spray. Check the fuel delivery. Is it in good condition? Loosen the fuel pipe connection at the injection pump inlet and test operate the fuel feed pump.
6.2. Major faults and troubleshooting

Fault 1. Engine won't start. Remedy Resupply Open Clean Disassemble and clean, or replace element (5) Air is sucked into the fuel due to defective Repair connections in the piping from the fuel tank to the fuel pump. (6) Fuel feed pump is damaged. Replace (7) Fuel freeze. Replace with a fuel for cold weather. Fuel delivered to (1) Defective connection of control lever and accel. rod Repair or adjust injection pump. of injection pump. (2) Plunger is worn out or stuck. Repair or replace (3) Delivery valve is stuck. Repair or replace (4) Control rack doesn't move. Repair or replace (5) Injection pump coupling is damaged, or the key is Replace broken. (6) Air sucking. Bleed air. (7) Plunger/Distribution shaft is seized. Replace pump. (8) Tappet is seized. Replace pump. (9) Stop solenoid is damaged. Replace (10) Cold start device is damaged. Replace (11) Low cranking speed. Replace battery. (12) Governor is damaged. Replace (13) Barrel crack Replace pump. (14) Transmission shaft is seized. Gear slip. Replace Cause Fuel not delivered (1) No fuel in the fuel tank. to injection pump. (2) Fuel tank cock is closed. (3) Fuel pipe system is clogged. (4) Fuel filter element is clogged.
55
doesn't (1) Nozzle valve doesn't open or close normally. (2) Nozzle seat is defective. (3) Case nut is loose. (4) Injection nozzle starting pressure is too low. (5) Nozzle spring is broken. (6) Fuel oil filter is clogged. (7) Excessive oil leaks from the nozzle sliding area. (8) Deformation due to excessive tightening of nozzle retaining bolt. (9) Strainer is clogged. Injection timing is (1) Injection timing is retarded due to failure of the coupling. defective. (2) Camshaft is excessively worn. (3) Roller tappet incorrectly adjusted or excessively worn. (4) Plunger is excessively worn. (5) Bad installation of injection pump. (6) Air sucking. (7) Delivery valve is defective. (1) Fuel pipe is cogged. 2. Engine starts, but immediately stops. (2) Fuel filter is clogged. (3) Improper air-tightness of the fuel pipe connection, or pipe is broken and air is being sucked in. (4) Insufficient fuel delivery from the feed pump. (5) Trochoid pump is defective. (6) Air sucking. (7) Electromagnetic feed pump is clogged. (8) Out of fuel. (9) Stop solenoid is defective. (10) Accumulator is abnormal. (1) Knocking sounds caused by improper (too fast) 3.Engine's Defective injection timing. output is injection insufficient. timing, and other (2) Engine overheats or emits large amount of smoke due to improper (too slow) injection timing. failures. (3) Insufficient fuel delivery from feed pump. (4) Torochoid pump is defective. (5) Type of fuel is incorrect. (6) Fuel tempererture is high. Nozzle (1) Case nut loose. movements (2) Defective injection nozzle performance. is defective (3) Nozzle spring is broken. (4) Excessive oil leaks from nozzle. Injection pump is (1) Max. delivery limit bolt is screwed in too far. defective. (2) Plunger is worn. (3) Injection amount is not uniform. (4) Injection timings are not even. (5) The 1st and 2nd levers of the governor and the control rack of the injection pump are improperly lined up. (6) Delivery holderr is loose (7) Delivery packing is defective. (8) Delivery valve seat is defective. (9) Delivery spring is broken. (10) Carbon deposit is adhered. (11) Spray pattern is abnormal. (12) Nozzle crack. (13) Plunger barrel crack.
Nozzle work.
Repair or replace Repair or replace Inspect and tighten Adjust Replace Repair or replace Replace the nozzle assembly Replace or adjust. Replace or clean Adjust Replace camshaft Adjust or replace Replace plunger assembly Adjust. Bleed air. Replace. Clean Disassemble and clean, or replace the element. Replace packing; repair pipe Repair or replace. Replace. Bleed air or hose check. Replace. Fill the fuel. Replace. Replace. Inspect and adjust Inspect and adjust Repair or replace Replace. Check and refill proper fuel. Cool. Inspect and retighten Repair or replace nozzle Replace Replace nozzle assembly Adjust Replace Adjust Adjust Repair Inspect and retighten Replace packing Repair or replace Replace Clean Replace Replace Replace fuel injection pump.
56
4. Idling is rough.
(1) Movement of central rack is defective. 1) Stiff plunger movement or sticking. Repair or replace 2) Rack and pinion fitting is defective. Repair 3) Movement of governor is improper. Repair 4) Delivery holder is too tight. Inspect and adjust (2) Uneven injection volume. Adjust (3) Injection timing adjustment failure. Adjust (4) Plunger is worn and fuel injection adjustment is Replace difficult. (5) Governor spring is too weak. Replace (6) Feed pump can't feed oil at low speeds. Repair or replace (7) Fuel supply is insufficient at low speeds due to Disassemble and clean, or clogging of fuel filter. replace element (8) Weight abnormality. Replace (9) Shifter is worn. (10) Air sucking. (11) Torochid pump is defective. (12) Governor is worn. Replace governor. Check piping. Replace Replace or adjust. Inspect and repair Inspect and repair Replace or adjust. Replace Repair or replace Replace Replace Check piping. Replace Adjust Adjust Adjust Adjust Repair Adjust Inspect and repair Adjust Repair or replace Adjust Inspect fuel system, clean Repair Inspect
5. Engine runs at high speeds, (1) The wire or rod of the accel is caught. but cuts out at low Speeds. (2) Control rack is caught and can't be moved. (3) Low idling stopper bolt is abnormal. 6. Engine doesn't reach max, (1) Governor spring is broken or excessively worn. rpm. (2) Injection performance of nozzle is poor. (3) Trochiod pump is defective. (4) Accumulator is abnormal. (5) Filter and pipe are clogged. (6) Governor is abnormal. (1) Injection timing is too fast or too slow. (2) Injection from nozzle is improper fuel drips after each infection. 7. Loud knocking. (3) Injection nozzle starting pressure is too high. (4) Uneven injection. (5) Engine overheats, or insufficient compression. 8.Engine When exhaust (1) Injection timing is too fast. exhausts too smoke is black: (2) Air volume intake is insufficient. much smoke. (3) The amount of injection is uneven. (4) Injection from nozzle is improper. When exhaust (1) Injection timing is too slow. smoke is white: (2) Water is mixed in fuel. (3) Shortage of lube oil m the engine. (4) Engine is over-cooled.
and
57
7. Tightening torques for main bolts and nuts

7.1. Pump part
No. 2 4 5 Name of parts Pipe joint bolt, fuel inlet Overflow joint, fuel outlet Bearing retaining screw Tightening torque ( N-m MP4 25 - 29 M121.25 25 - 29 M121.25 8 - 10 M61hexagon socket head 40 - 45 9 Timer holder M221 30 - 35 M161 11 Plug, cooling water 12 Accumulator 14 Bolt, trochoid pump 15 Bolt, driving shaft 17 Retaining screw, rack guide 22 - 25 M141 50 - 55 M201 8 - 10 M61 8 - 10 M61hexagon socket head 3-4 M40.7hexagon socket head 32 End nut 33 plug, rack 31 Nut, FIC fixing flange 113 - 123 M181.5 79 - 84 M121.25 4-5 M61 25 Bolt, rink lifter 24 plug, strainer 22 Head bolt MP2 No. Name of parts Tightening torque ( N-m MP4 4-5 M61hexagon socket head 50 - 55 M181 40 - 45 M141.25 28 - 32 M101.5 hexagon socket head 18 - 22 M81.25 hexagon socket head 30 - 35 M141 MP2
18 Tappet guide 19 Plug, barrel 21 Delivery holder
10 Thermo element
23 Plug, distribution shaft
15 - 20 M221 25 - 29 M121.25 8 - 10 M61 78 - 88 M141.5
58
7.2. Mechanical governor part

No. Name of parts 1 Fixing bolt, tension lever hook 5-7 M50.8 3 4 7 8 9 Angleich complete Nut, fuel limiter Setting bolt, min. idling speed Nut, speed lever Setting nut, max. idling speed 25 - 29 M141 19.6 - 21.6 M121.25 8 - 10 M61 19.6 - 21.6 M81.25 8 - 10 M61 16 Bolt, back cover 15 Cap nut 14 Starting fuel limiter 6-8 M50.8 20 - 22 M121.25 8 - 10 M61 13 Bolt, governor assy Tightening torque ( N-m MP4 6-8 M61 2 Fixing bolt, patch 11 Bolt, governor lever shaft MP2 10 Bolt, solenoid No. Name of parts Tightening torque ( N-m MP4 8 - 10 M61 8 - 10 M61 8 - 10 M61 8 - 10 M61 MP2
59
8. Tools
Name of tool Nozzle plate 158090-51700 Shape and size application
Bottom clearance gauge 158090-51800 : MP2 158090-51810 : MP4
Bottom clearance gauge
Plunger SP seat extractor 158090-51900
60
Literature No. M9961-03E070
Revision history list Document name Product name Revision No.

Revision date (A.D.)
Reason for revision YDP-MP2 / YDP-MP4 Revision outline
Page No
SERVICE MANUAL FOR FUEL INJECTION EQUIPMENT Revision item (page)
Revised by
2004 KOMATSU UTILITY EUROPE S.p.A. All Rights Reserved Printed in Europe

4d88e Yanmmar

Uploaded by

Copyright:

Available Formats

4d88e Yanmmar

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4d88e Yanmmar

Uploaded by

Copyright:

Available Formats

SHOP MANUAL

DANGER-indicates an imminently hazardous situation, which,

Safe / Adequate Work Area

Bright, Safely Illuminated Area

(2) WORK WEAR (GARMENTS Safe Work Clothing

(3) TOOLS Appropriate Lifting / Holding

(4) GENUINE PARTS and MATERIALS Genuine Parts

(5) FASTENER TORQUE Torqueing Fasteners

(6) Electrical Short Circuits

(7) WASTE MANAGEMENT

(8) FURTHER PRECAUTIONS Fueling / Refueling

Preventing burns from scalding

Precautions for Service Work

(2) Preparation for Service Work

(3) Preparation before Disassembly

(4) Precautions in Disassembly

(5) Precautions for Inspection and Measurement

(6) Precautions for Reassembly

(7) Precautions for Adjustment and Check

How to Read this Manual

(2) How to Read the Explanations

(3) Definition of Terms

1.4 Engine External Views........................................................................................................... 16

1.6 Exhaust gas emission regulation........................................................................................... 18

2. Inspection and Adjustment........................................................................ 22

4. Disassembly, Inspection and Reassembly of Engines.............................. 59

4.2 Cylinder Head: Disassembly, Inspection and Reassembly.................................................... 70

4.3 Gear Train and Camshaft ...................................................................................................... 83

4.4 Cylinder Block........................................................................................................................ 90

5. LUBRICATION SYSTEM ........................................................................ 108

7. FUEL INJECTION PUMP/GOVERNOR...................................................114

7.2 Fuel Injection Pump..............................................................................................................114

8. TURBOCHAGER: Disassembly, inspection and reassembly.....................118

8.2 Service Standards and Tightening Torque ........................................................................... 121

8.3 Periodic Inspection Procedure............................................................................................. 123

8.4 Disassembly Procedure....................................................................................................... 127

8.5 Washing and Inspection procedure ..................................................................................... 130

8.6 Reassembly Procedure ....................................................................................................... 134

8.6.2 Reassembly .........................................................................................................................134

8.7 Handling after Disassembly and Reassembly ..................................................................... 137

8.8 Troubleshooting ................................................................................................................... 138

9. STARTING MOTOR ................................................................................ 140

9.2 For 4TNV106(T) .................................................................................................................. 156

10. ALTERNATOR....................................................................................... 176

10.2 Troubleshooting ................................................................................................................. 179

11. ELECTRIC WIRING .............................................................................. 180

12. SERVICE STANDARDS ....................................................................... 185

12.3 Lubricating Oil System (Trochoid Pump) ........................................................................... 195

13. TIGHTENING TORQUE for BOLTS and NUTS .................................... 196

Engine speed Constant speed Variable speed

Available engine speed (min-1) 1500/1800 2000-3000

9.9 12.0 (13.5) (16.3) 1500 1800

11.3 13.5 (15.3) (18.3) 1500 1800

26.3 27.4 28.5 (35.8) (37.3) (38.7) 2590 2700 2810

16.4 19.6 (22.3) (26.7) 1500 1800

410 mm O/D, 6 blades pusher type

410 mm O/D, 6 blades pusher type

430 mm O/D, 8 blades suction type

1.3 Fuel Oil, Lubricating Oil and Coolant Water