Led 5mm y

D+LED-LD5Y
D+LED-LD5Y
Descriptions:
5mm round2-pin lamp LEDwater clear lens
Features:
z z z z z z DIP LED Type Sizemm:5*8.6 Emitting Color: Yellow View angle at 30 Pb-free wave soldering application RoHS Compliant
Applications:
z z z
Decorative lighting Indicators Illuminations
CUSTOMER APPROVED
APPROVED BY
CHECKED BY
PREPARED BY
_____________________________________________________
D+LED-LD5Y
Absolute Maximum Ratings (Ta = 25)
Items Forward Current(DC) Peak Forward Current* Power Dissipation Operation Temperature Storage Temperature Reverse Voltage Soldering Temperature
*Pulse width1msec duty1/10
Symbol IF IFP PD Topr Tstg VR Tsol
Absolute maximum Rating 50 100 120 -40 ~ +95 -40 ~ +100 5
Unit mA mA mW V
Reflow Soldering:260/3sec Hand Soldering: 300/3sec
Typical Electrical & Optical Characteristics ( Ta = 25)

Items Forward Voltage Reverse Current Dominant Wavelength Luminous Flux Luminous Intensity 50% Power Angle Symbol VF IR D V IV 2 Condition IF = 20mA VR = 5V IF = 20mA IF = 20mA IF = 20mA IF = 20mA ----580 --2.0 4500 30 ----Min. 1.7 Typ. --Max. 2.4 5 595 Unit V uA nm lm mcd Deg
Material
Item Material Standard Bins
Rank(IF=20mA) Luminous Intensity(mcd) Forward Voltage(V) Dominant Wavelength(nm)
Reflector Iron
Wire Gold
Encapsulate Epoxy
Chip AlGaInP
Code L20 3115~4360 V3 1.8~2.0 Y5 588~590 L21 4360~6105 V4 2.0~2.2 Y6 590~592 L22 6105~8550 V5 2.2~2.4 Y7 592~594
*Tolerance of measurement of forward voltage is0.1V *Tolerance of measurement of luminous intensity or flux is15. *Tolerance of measurement of dominant wavelength is1nm.
_____________________________________________________
D+LED-LD5Y
Package Dimensions (unit: mm)
Notes
All dimensions are in mm. Tolerance is 0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy may be 0.5 mm max.
_____________________________________________________
D+LED-LD5Y
Typical Electrical/Optical Characteristics Curves(Ta=25 Unless Otherwise Noted)
If(mA)
50 40 30 20 10 0 1.4 1.6 1.8 2.0 2.2 Vf(v) 2.4 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 If(mA) 50
IV 100%
Fig. 1 Forward Current vs Forward Voltage
Fig. 2 Relative Luminous Intensity vs Forward Current
If(mA)
100 80 60 40 20 0 0
IV 100%
100% 80% 60% 40% 20%
Ta(C)
20
40 60 80 100
0 400 450 500 550 600 650

Fig. 4 Relative Luminous Flux vs Wavelength 10 0 10
WL(nm) 700
Fig. 3 Maximum Forward Current vs Ambient Temperature
200% 100% 50% 20% 10% -30 -10 10 30 50 70

40 50 60 70 80
30
20
20
30 40 50 60 70 80
Ta(C)
90 100% 75%
50%
25%
25%
90 50% 75% 100%
Fig. 5 Relative Luminous Flux vs Ambient Temperature
Fig. 6 Relative Luminous Flux vs Radiation Angle
_____________________________________________________
D+LED-LD5Y
Precautions for use:
1. Storage Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temperature after soldering Avoid quick cooling Lead frames are silver plated copper alloy. The silver plate surface may be affected by environments which contains corrosive substances. Please avoid conditions which may cause the LEDs to corrode,tarnish or discolour 2. Soldering Manual Soldering Solder Dipping 110 max Soldering Iron 35W max. Preheat 280 max(63/37 Solder) Temperature Preheat time 60 seconds max. 300 max(Pb free solder) Solder temperature 63/37 Solder:235(245max) Pb-free solder:255 (260 Soldering Time 3 seconds max. max) Position Not less than 3mm from Dipping Time 3 seconds max. the base of the epoxy Position Not less than 3mm from the base of the epoxy Recommended soldering profile:
Temperature( ) 300 laminar wave 250 200 150
100 50 Preheat 0 0 10 20 30 40 50 60 70 Times(Sec) 80 90 100 110 120
Solder=Sn 63-Pb 37 Peak preheat temperature:100-110 Total preheat time:50-60seconds Peak profile fit temperature:235(max 245)
Solder= Pb-Free Peak preheat temperature:100-110 Total preheat time:50-60seconds Peak profile fit temperature:260max
Dwell time above 200 should not exceed 3 Dwell time above 200 should not exceed 3 seconds seconds
_____________________________________________________
D+LED-LD5Y
Caution The LEDs must not be repositioned after soldering Do not apply any stress to the lead particularly when heat
3. Static Electricity Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band, ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded
Others Reverse voltage should not exceed the absolute maximum rating on the data sheet. The LED leads may become tarnished if they contact hydrogen sulphide or other gaseous chemicals. The colour of the LEDs is changed slightly an operating current and thermal. This device should not be used in any type of fluid such as water, oil, organic solvent and etc When washing is required, IPA (Isopropyl Alcohol) should be used. The influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the way. Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal, It is also dangerous to drink the liquid or inhale the gas generated by such products when chemically disposed. High-brightness LED light may injure human eyes. Avoid looking directly into lighted LED The appearance and specifications of the product may be modified for improvement without notice.
4.
_____________________________________________________

Led 5mm y

Uploaded by

Copyright:

Available Formats

Led 5mm y

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Led 5mm y

Uploaded by

Copyright:

Available Formats

D+LED-LD5Y

Decorative lighting Indicators Illuminations

Symbol IF IFP PD Topr Tstg VR Tsol

Absolute maximum Rating 50 100 120 -40 ~ +95 -40 ~ +100 5

Reflow Soldering:260/3sec Hand Soldering: 300/3sec

Typical Electrical & Optical Characteristics ( Ta = 25)

Fig. 1 Forward Current vs Forward Voltage

Fig. 2 Relative Luminous Intensity vs Forward Current

0 400 450 500 550 600 650

Fig. 3 Maximum Forward Current vs Ambient Temperature

200% 100% 50% 20% 10% -30 -10 10 30 50 70

90 50% 75% 100%

Fig. 5 Relative Luminous Flux vs Ambient Temperature

Fig. 6 Relative Luminous Flux vs Radiation Angle

100 50 Preheat 0 0 10 20 30 40 50 60 70 Times(Sec) 80 90 100 110 120

You might also like