i

iPASOLINK 1000
CHAPTER I INSTALLATION
CONTENTS
iPASOLINK 1000: INSTALLATION NWD-118789-04E
December, 2011
1. OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. COMPOSITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1.1 IDU and ODU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.1.2 Pole Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.1.3 iPASOLINK 1000 Composition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.1.4 IDU and ODU for 1+0 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.1.5 IDU and ODU for 1+1 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2.2 iPASOLINK 1000 IDU Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.1 Cards for Universal Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.1.1MODEM-A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.1.2STM-1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.1.316E1-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.1.4GbE-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.1.5AUX-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.1.6MSE-A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.1.7CWDMFA/CWDMFB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.2 Fundamental Cards for iPASOLINK 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.2.2.1MC-M (Main Card). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.2.2.2PS-M (Power Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.2.2.3TERM-M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.2.3 CWDM Filter Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.2.3.1CWDMFA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.2.3.2CWDMFB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
3. UNPACKING IDU and ODU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
4. MOUNTING IDU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Mount IDU / CWDM Filter Box Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Replace FAN Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.3 Replace MODEM-A/(*)-A Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.4 Replace MC-M Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.5 Replace CLK2M-C Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
ii CONTENTS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4.6 Replace PS-M Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
4.7 Replace PS-M Fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
4.8 Replace TERM-M Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
4.9 CWDM Filter Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
4.9.1IDU and Filter Box Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
4.9.2Mount CWDMF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
4.10 Mount SFP Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
4.10.1SFP Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-24
4.10.2Colored SFP Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25
5. MOUNTING ODU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Antenna Direct Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.1.1 Basic Installation for Antenna & ODU. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
5.1.2 With Hybrid/Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
5.1.3 With TX Span Attenuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36
5.1.4 With Ortho-Mode Transducer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-39
5.2 Feeder Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
5.2.1 For Coaxial Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-45
5.2.2 For Waveguide Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49
5.2.3 For Waveguide Connection with Hybrid . . . . . . . . . . . . . . . . . . . . . . . . . 5-54
5.3 Other Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60
5.3.1 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-60
5.3.2 Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-64
5.4 Hybrid Combiner Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-66
6. ADJUSTING CABLE ENDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 5D Coaxial Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6.2 8D Coaxial Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-32
6.3 Other Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-44
7. WIRING and FORMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
7.2.1 Connector Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
7.2.2 Connect I/F Cable with L-angle Plug to IDU . . . . . . . . . . . . . . . . . . . . . . . . 7-4
7.3 Rout Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
7.3.1 Grounding Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
7.3.2 IF Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
CONTENTS iii
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.3.3 Power Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
7.3.4 16E1, STM-1, GbE and AUX Signal Cables . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
7.3.5 XIF Coaxial Cables (XPIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
7.3.5.1Connection for XPIC 1+0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
7.3.5.2Connection for XPIC 1+1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10
7.3.6 Cables Using CWDM Filter Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
7.3.6.1Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
7.3.6.2For CWDMF on IDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
7.3.6.3For CWDM on Filter Box Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12
7.4 Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
7.4.1 MC-M Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
7.4.2 TERM-M Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
7.4.3 PS-M Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
7.4.4 AUX-A Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
7.4.5 16E1-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
8. GROUNDING THE FRAME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
9. WATERPROOFING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
10. START-UP and SHUT-DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.1 Start-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
10.2 Shut-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
10.3 System #2 #4 ODU Expansion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
11. ORIENTING ANTENNA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
iv /END CONTENTS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.
OVERVIEW 1-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
1. OVERVIEW
The standard installation is summarized in this section. Following shows the typical
installation work flow and guides to IDU installation, ODU installation, Antenna
(ANT) installation, waveguide connection and coaxial cable connections. The
installation flow chart is shown below.
This product is a part of the radio link system, and is intended to be connected with a
external antenna.
This product should be installed and operated by skilled personnel.
After the installation, the system should be ensured to comply with the relevant limits
for general public exposure specified as basic restrictions or reference levels in the
council Recommendation 1999/519/EC.
Figure 1-1 Typical Installation Flow Diagram
Unpacking IDU
(see Section 3.)
Unpacking ODU
(see Section 3.)
Mounting ODU
(see Section 5.)
Mounting IDU
(see Section 4.)
Grounding
the Frame
(see Section 8.)
Terminating Cables
(see Section 6.)
Waterproofing
(see Section 9.)
Wiring and Forming
(see Section 7.)
Orienting Antenna
(see Section 11.)
1-2/END OVERVIEW
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.
COMPOSITIONS 2-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2. COMPOSITIONS
2.1 Overview
Each unpacked component of the [ ] GHz [ ] MB digital radio system must be
checked as shown below:
Contents List Subsection
IDU and ODU 2.1.1 IDU and ODU
Mounting Bracket 2.1.2 Pole Mounting Bracket
iPASOLINK 1000 Composition 2.1.3 iPASOLINK 1000 Composition
Installation Kit 2.1.4 IDU and ODU for 1+0 System
2.1.5 IDU and ODU for 1+1 System
2.2.1 Cards for Universal Slots
2.2.2 Fundamental Cards for iPASOLINK 1000
2.2.3 CWDM Filter Box
2-2 COMPOSITIONS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2.1.1 IDU and ODU
Note*: Two spare fuses are provided in the IDU packing box.
Figure 2-1 Contents of Cards
No. Description
1 TRP-( )G-1D (ODU)
2 MDP-400MB-1BB (IDU)
3 O-Ring (Attached to the waveguide type ODU)
4 Power Connector [Housing (AMP: 1-178288-8 (x1 ea)) or DK-3100S-10R (x1 ea) and
Socket Contacts (AMP: 1-175218-2 (x10 ea))]
5 Cylindrical Fuse (ES1-12500 (250 V/12.5 AH))*
3
1
5
4
(13-42 GHz)
(6-11 GHz)
2
COMPOSITIONS 2-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2.1.2 Pole Mounting Bracket
Figure 2-2 Pole Mounting Bracket
2.1.3 iPASOLINK 1000 Composition
Figure 2-3 iPASOLINK 1000 Composition
No. Description
1 Pole Mounting Bracket for Coaxial Cable (6/7/8 GHz)/Waveguide Connection Type
2 Pole Mounting Bracket for Antenna direct Mounting Type
(Supplied with Antenna)
2
1
Universal Slot #1 Universal Slot #2 Universal Slot #3 Universal Slot #4
Universal Slot #5 Universal Slot #6 Universal Slot #7 Universal Slot #8
Universal Slot #9
Universal Slot #10
MAIN CARD 1
TERM PS 1
FAN1
FAN2
Main Card Slot #2
Universal Slot #11 Universal Slot #12 Universal Slot #13 Universal Slot #14
PS Slot #2
Slot #
Slots for fundamental cards that must be mounted.
Slots for option cards, which can be left vacant.
PS Power Supply
Main Card Slot #1
2-4 COMPOSITIONS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2.1.4 IDU and ODU for 1+0 System
Figure 2-4 IDU and ODU to be Installed for 1+0 System
ODU (13-42 GHz)
N-P connector N-P connector
ODU (6-11 GHz)
Earth Screw
(FG)
TNCP Connector
Earth Screw (FG)
Earth Screw
(FG)
COMPOSITIONS 2-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2.1.5 IDU and ODU for 1+1 System
Figure 2-5 IDU and ODU to be Installed for 1+1 System
ODU (6-11 GHz) ODU (6-11 GHz)
N-P connector
TNCP connector
N-P connector
ODU (13-42 GHz)
N-P connector
TNCP connector
N-P connector
Earth Screw Earth Screw
ODU (13-42 GHz)
Earth Screw Earth Screw Earth Screw Earth Screw
(FG)
(FG) (FG) (FG) (FG)
(FG)
2-6 COMPOSITIONS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2.2 iPASOLINK 1000 IDU Components
2.2.1 Cards for Universal Slots
2.2.1.1 MODEM-A
2.2.1.2 STM-1A
2.2.1.3 16E1-A
TNC Connector
Earth Screw XIF Connectors MD/ODU PWR Switch
SFP Module Ports
CLASS 1 LASER PRODUCT
MDR Connector
COMPOSITIONS 2-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2.2.1.4 GbE-A
2.2.1.5 AUX-A
2.2.1.6 MSE-A
2.2.1.7 CWDMFA/CWDMFB
See 2.2.3 CWDM Filter Box.
RJ45 Modular Ports
CLASS 1 LASER PRODUCT
SFP Module Ports
Hi-Density D-Sub (44) Connector
2-8 COMPOSITIONS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2.2.2 Fundamental Cards for iPASOLINK 1000
2.2.2.1 MC-M (Main Card)
2.2.2.2 PS-M (Power Supply)
2.2.2.3 TERM-M
Protection Switch
OW Outlet
CALL Push Button
USB Port
R45 Modular Ports
SFP Module Ports
High-Density D-Sub 44-pin Connector
CLASS 1 LASER PRODUCT
Power Supply Connector
R45 Modular Ports
High-Density D-Sub 15-pin Connector
COMPOSITIONS 2-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2.2.3 CWDM Filter Box
NOTE: CWDM Fitter Box (CWDMF) is not a managed object within IDU. Thus,
retrieving the information of status, inventory, etc., regarding the CWDMF is
not available. However, the inventory information for the Colored SFP only
can be retrieved.
2.2.3.1 CWDMFA
2.2.3.2 CWDMFB
SFP Module Ports
LC Connector Port
CLASS 1 LASER PRODUCT
CLASS 1M LASER PRODUCT
SFP Module Ports
LC Connector Port
CLASS 1M LASER PRODUCT
CLASS 1 LASER PRODUCT
2-10/END COMPOSITIONS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.
UNPACKING IDU and ODU 3-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3. UNPACKING IDU and ODU
Procedures for unpacking IDU and ODU are shown in following chart.
IDU: Procedure 3-1
ODU: Procedure 3-2
Note When conveying the IDU or ODU to another place, the original packing
should be used to avoid damage.
Procedure 3-1 Method of Unpacking IDU
1 Open the container box.
Shipping Tag / Packing Slip
(with bar-code)
3-2 UNPACKING IDU and ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2 Unbox the contents. The contents are boxed as shown below:
3 Remove the polyethylene sheet from IDU.
4 Inspect IDU.
Top Pad
(Accessories are taped on the top pad.)
SFP
SFP
FUSE
FUSE
(Desiccant)
IDU
Polyethylene Sheet
Bottom Pad
Container Box
UNPACKING IDU and ODU 3-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Procedure 3-2 Method of Unpacking ODU
1 Remove the top cover of the packing box.
Recycle Mark
Package Label
Package Label
or
Recycle Mark
Care Label
Care Label
3-4/END UNPACKING IDU and ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2 Unbox ODU, cushioning materials (pads) and polyethylene sheet:
3 Remove the polyethylene sheet from ODU.
4 Inspect ODU.
Top Pad
Polyethylene Sheet
Bottom Pad
Container Box
MOUNTING IDU 4-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4. MOUNTING IDU
4.1 Mount IDU / CWDM Filter Box Mount
NOTE: Procedure below uses IDU for example.
Procedure 4-1 Methods of Mounting IDU
1 Supporting brackets are attached on the front of IDU.
2 Mount IDU onto the 19-inch Rack. Example below uses EIA 310-D [IEC-60297]
Rack:
Attach and half-tighten two screws (with spring and flat washers) for the bottom
side (or for the upper side if the rack is IEC-60917) of the shelf.
Hook the bottom-side (or upper-side if the rack is IEC-60917) keyholes of the
flanges onto these screws ().
Secure all four screws (with spring and flat washers) including half-tightened
screws ().
Front Side
Rear View
Screw
Spring Washer
Flat Washer

Keyhole
Screw Hole
4-2 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Since the forced-air cooling fans are built in, IDU does not require spaces for the
heat dissipation on its top, bottom and rear when installing onto a 19-inch Rack.
However, to install cables, the space of about 1U [1.75 inches; 44.45 mm] each
above and below the IDU is required.
IDU
1U
1U
(wall)
1U = 1.75 inches / 44.45 mm
1U
(side view)
MOUNTING IDU 4-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.2 Replace FAN Unit
Notes
1. NEC recommends that FAN unit be replaced approximately every three
years, regardless of its condition.
2. If a FAN alarm occurs, replace the FAN unit immediately.
3. The FAN unit is hot-swappable, which allows the replacement without
shutting down the system.
4. When replacing a FAN, a new FAN unit to be mounted should be
prepared near.
Procedure 4-2 Replace FAN Unit
1 Dismount the defective FAN
Proceed with the illustrated steps in reverse:
Step 2: Using the screwdriver, loosen the screw.
Step 1: Holding the screw, pull the unit out.
2 Mount a new FAN
Proceed with the illustrated steps in a regular order:
Step 1: Insert the new FAN unit.
Step 2: Using the screwdriver, tighten the screw.
4-4 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Step 1
Step 2
FAN Unit
Screw (on lower FAN)
Screw (on upper FAN)
MOUNTING IDU 4-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.3 Replace MODEM-A/(*)-A Card
Note (*)-A: STM1-A, 16E1-A, GbE-A, MSE-A and AUX-A cards; the
procedures for replacing these cards are the same as that for MODEM-A
card, except for the PWR switch that only MODEM-A has.
Procedure 4-3 Replace MODEM-A/(*)-A Cards
1 Set the MD PWR switch on the MODEM-A card to OFF position.
2 Dismount the defective MODEM-A(*) card as shown below:
Using the screwdriver, loosen two screws.
Screw
Screw
4-6 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Holding the screws, pull the MODEM-A off from the slot.
3 Mount a new MODEM-A(*) card as shown below:
Place the card on the card slot guides of the chassis, then carefully push the
card till it is fully engaged to the chassis backboard.
MOUNTING IDU 4-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Ensure not to touch any interfacing parts, carefully insert the card further into
the slot.
Using the screwdriver, secure the card by tighten the screws.
Warning: Ensure not to touch electrical devices on the card.
Screw
Screw
4-8 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4.4 Replace MC-M Card
Procedure 4-4 Replace MC-M Card
NOTE: Before starting the procedure, check if the MC-M Card to be removed has its
associated MC-M:
If the MC-M Card to be removed is unprotected, or is protected but the last remaining of
the two, turn off the power of MODEM-A Card before starting the procedure.
If the MC-M Card has its associated MC-M configuring the protection group, ensure that
the MC-M to be removed is on the Standby mode, and in the OOS status.
1 Dismount the defective MC-M card:
Using the screwdriver, loosen two screws.
Pull two ejectors on the card outward.
Ejector
Ejector

Screw

Screw
MOUNTING IDU 4-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Pull the card out from the slot.
3 Install a new MC-M card:
Place the card on the card slot guides of the chassis.
Carefully insert the card further till it is fully engaged, and press the two
ejectors on the card to lock them.

4-10 MOUNTING IDU

NWD-118789-04E iPASOLINK 1000: INSTALLATION
(1) Using the screwdriver, tighten the screws.
Warning: Ensure not to touch electrical devices on the card.
Screw
Screw
MOUNTING IDU 4-11
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.5 Replace CLK2M-C Card
To replace the defective CLK2M-C Card on the MC-M Card, proceed with the
following:
Procedure 4-5 Replace CLK2M-C Card
1 Dismount MC-M Card following Procedure 4-4 Replace MC-M Card.
2 Dismount CLK2M-C Card:
Remove the screw that secures the CLK2M-C Card on MC-M Card.
Warning: Ensure not to touch electrical devices on the card.
Screw
securing CLK2M-C Card
4-12 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Refering to the illustration below, remove the screw that secures the spacer
from the rear surface.
Dismount CLM2M-C Card.
Warning: Ensure not to touch electrical devices on the card.
3 Mount CLK2M-C Card:
Place the spacer on surface of the MC-M Card.
Spacer

CLK2M-C Card

Screw securing the spacer

MOUNTING IDU 4-13
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Tighten the spacer using the screw from the rear surface of MC-M Card.
Set the CLK2M-C Card on the connector provided on the MC-M Card.
Secure the CLK2M-C card using the screwdriver and screw.
Spacer

CLK2M-C Card

4-14 MOUNTING IDU

NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Verify the installed CLK2M-C Card.
Warning: Ensure not to touch electrical devices on the card.
5 Mount MC-M Card following Procedure 4-4 Replace MC-M Card.
CLK2M-C Card
MOUNTING IDU 4-15
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.6 Replace PS-M Card
Procedure 4-6 Replace PS-M Card
1 Power off the equipment:
Disconnect the power cable(s) from PS-M Card(s).
Confirm that the PWR LED lamp(s) is/are off.
2 Dismount the defective PS-M card:
Using the screwdriver, loosen the screws.
Power Cable port
PWR LED
on PS-M Card 1
Power Cable port
on PS-M Card 2
PWR LED
Screw
Screw
4-16 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Holding the screws, pull the card out from the slot.
3 Mount a new PS-M card:
Place the card on the card slot guides of the chassis.
MOUNTING IDU 4-17
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Suspend the screws by pulling them outward.
Ensure not to touch interface parts, insert the card further till it is fully engaged
with the chassis backboard.
Using the screwdriver, tighten the screw.
Warning: Ensure not to touch electrical devices on the card.
4 Connect the Power Cable to turn on the power.
Screw
Screw
4-18 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4.7 Replace PS-M Fuse
Procedure 4-7 Replace PS-M Fuses
1 Dismount the PS-M card following Procedure 4-6 Replace PS-M Card.
2 Remove the defective Fuse:
Remove the protective cover of the fuse.
Remove the fuse.
3 Set a new fuse.
4 Set the protective cover.
Warning: Ensure not to touch electrical devices on the card.

MOUNTING IDU 4-19

iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.8 Replace TERM-M Card
Procedure 4-8 Replace TERM-M Card
1 Power off the equipment:
Disconnect the power cable(s) from PS-M Card(s).
Confirm that the PWR LED lamp(s) is/are off.
2 Dismount the defective TERM-M card:
Disconnect the cables if connected.
Using the screwdriver, loosen the screws.
Power Cable port
PWR LED
on PS-M Card 1
Power Cable port
on PS-M Card 2
PWR LED
TERM-M Card
Screw Screw
4-20 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Holding the screws, pull the card out from the slot.
3 Mount a new TERM-M card:
Place the card on the card slot guides of the chassis.
Suspend the screws by pulling them outward.
Ensure not to touch interface parts, insert the card further till it is fully engaged
with the chassis backboard.
MOUNTING IDU 4-21
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Using the screwdriver, tighten the screws.
Warning: Ensure not to touch electrical devices on the card.
4 Connect cables back in place to TERM-M Card, if required.
5 Connect the Power Cable(s) to PS-M Card(s) to turn on the power.
Screw
Screw
4-22 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4.9 CWDM Filter Box
Important:
Between the associated sites, a CWDM Filter Box A in one site, and CWDM Filter
Box B in the other site must be installed in pair for the use of designated IN and OUT
ports. See 7.3.6 Cables Using CWDM Filter Boxes for reference.
4.9.1 IDU and Filter Box Mount
CWDM Filter Box can be installed in to the Universal Slots, but it has no back pins to
connect with IDU. Thus, CWDM can also be placed out of the IDU using a Filter
Box Mount (a dedicated chassis for CWDM Filter Box) if no vacant slot is found in
the IDU.
CWDM Filter Boxes in IDU (Example)
CWDM Filter Boxes in Filter Box Mount
MOUNTING IDU 4-23
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.9.2 Mount CWDMF
Since CWDM Filter Box has no back pins, installing it either on IDU or Filter Box
Mount requires to secure the CWDM Filter Box using two screws only:
Insert the CWDMF into the Card Slot, and fasten two screws:
Screw
Screw
4-24 MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4.10 Mount SFP Module
4.10.1 SFP Module
The Small Form-factor Pluggable (SFP) is a compact and hot-pluggable transceiver
designed to support Gigabit Ethernet (GbE) and/or SDH (STM-1) in the
iPASOLINK.
iPASOLINK offers the following five options for SFP modules:
1) Single Mode Fiber (SMF): This SFP complies with GbE along with SDH. The
SFP operates with the 1310 nm laser transmitter and has a duplex LC
connector.
2) Multi Mode Fiber (MMF): This SFP complies with 1.25 Gbps 1000 BASE-SX
Gigabit Ethernet. The SFP operates with the laser transmitter and has a duplex
LC connector.
3) Electrical SFP (RJ45): This SFP complies with 10/100/1000 BASE-T copper
interface.
Note SyncE function is not supported on Electrical SFP.
4) Electrical SFP (DIN 1.0/2.3): This SFP complies with STM-1e SDH interface.
5) Colored SFP: See 4.10.2 Colored SFP Module.
The SFP modules also accept LC fiber connectors with Polished Connector (LC-PC)
or Ultra Polished Connector (LC-UPC).
For the purpose of the use in iPASOLINK, it is recommended to use SFPs that are
designated and supplied by NEC.
SFP Module Ports [MC-M]
[SFP Module Ports when GbE-A Card(s) is/are mounted.]
SFP Module Ports [STM1-A on any Universal Slot]
MOUNTING IDU 4-25
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4.10.2 Colored SFP Module
For the use of CWDM, following SFP are provided. Depending on the applicable
wavelength, a colored tape is applied on the extraction lever of each SFP:
Table 4-1 Types of SFP and Colors
Wavelength Color Indication on Extraction Lever
1470 nm Gray
1490 nm Violet
1510 nm Blue
1530 nm Green
1550 nm Yellow
1570 nm Orange
1590 nm Red
1610 nm Brown
EXTRACTION LEVER
4-26/END MOUNTING IDU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 4-9 Mount SFP Module (Example: IDU)
1 Mount an SFP module onto the SFP port till it clicks and is fully engaged:
SFP modules are mounted
MOUNTING ODU 5-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5. MOUNTING ODU
The procedures for mounting and dismounting the ODU are described here. There are
two types of mounting for the Antenna Direct Mounting type and Feeder Connecting
type. The ODU should be installed in the radio station.
The tools for installation are listed in Table 5-1.
Caution
1. How to use small and large O-rings are shown in following table. Two
(small and large) O-rings are attached in 18 to 42 GHz band Andrew/RFS
direct mount antenna. 11/13/15 GHz band antenna does not have small O-
ring (Small O-ring is not used for Andrew/RFS direct mount antenna). If the
small O-ring is used for ODU direct mount installation, a gap may occur
between ODU and antenna for RF interface. Therefore it may happen
transmit or receive level down.
2. Do not apply silicon grease at O-ring.
Note 11/13/15 GHz antenna for direct mount is not possible to connect the
ordinary waveguide flanges.
Table 5-1 Tools
Tools
Wrench or Monkey Wrench
Screwdriver
Torque Wrench
System
Attachment Position of
O-ring (Between:)
O-ring
Remarks
Small Size Large Size
1+0 ANT ODU Not used Used Antenna direct mounting
ANT WG/ODU
(18 42 GHz BAND)
Used Not used Waveguide connection
1+1 ANT Hybrid/Coupler Not used Used Antenna direct mounting
ANT WG/Hybrid/Coupler
(18 42 GHz BAND)
Used Not used Waveguide connection
5-2 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Notes
1. Do not use both small O-ring and large O-ring simultaneously.
2. O-ring size is different with frequency band as follows:
Position of
large size
O-ring
Position of
small size
O-ring
For Waveguide Connection For Antenna Direct Mounting
ANDREW Antenna
Position of
large size
O-ring
Position of
small size
O-ring
RFS Antenna
For Waveguide Connection For Antenna Direct Mounting
3
2
m
m
3
5
m
m
Large Size O-ring for Antenna Direct Mounting
26-42 GHz Band
4
0
m
m
10-11 GHz Band 13-23 GHz Band
4

m
m
4

m
m
4

m
m
18/23 GHz Band 32/42 GHz Band
1
5
.
6
m
m
Small Size O-ring for Waveguide Connection
1
0
.
8
m
m
1
.
8

m
m
1
.
8

m
m
MOUNTING ODU 5-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5.1 Antenna Direct Mounting
5.1.1 Basic Installation for Antenna & ODU
Note The details are referred to the installation manual which is attached to
the antenna.
Installation of Bracket
1 Install the bracket to the antenna pole,
2 Mount antenna to the bracket,
ANDREW pole mount bracket
for other reflector type
Washer
Note *: Tightening torque of 22 Nm for M10.
Three(3) screws*
(Apply screwtight to threads
before fitting to antenna)
Nut*
Protective cap
Lock washer
ANDREW pole mount bracket
for 1 or 2 ft reflector type
Lock washer
Washer
Nut
Clamp Bracket
5-4 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
RFS SB1 Type Bracket
MOUNTING ODU 5-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Note The values in the following table are valid for screws and bolts which
have been greased according to the installation instructions.
Torques for RFS
Bolt M5 5 Nm
M6 8 Nm
M8 17 Nm
M10 35 Nm
M12 50 Nm
U-Bolt, V-Bolt (Pipe mount & safety collar) M10 20 Nm
Hexagonal brass nut of fine adjustment (Azimuth, Elevation) M8 5 Nm
M10 10 Nm
M12 17 Nm
Hexagonal socket stainless steel screws
(Feed systems install on aluminium mounting plate)
M3 0.2 Nm
M4 0.4 Nm
Exceptions
Fixing screw of the azimuth fine adjustment spindle M8 x 30 8 Nm
M12 x 55 17 Nm
Special application: NOT greased
Fixing screw of the plastic radome B4.2 3 Nm
5-6 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Pipe diameter: 48-114 mm
RFS C-Mount Type Bracket
Mount Assembly (RFS C-Mount Type)
MOUNTING ODU 5-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
RFS C-Mount Type Bracket
6
7
5-8 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Fix the ODU to the bracket by tightening the M6 screws (four locations),
Notes
1. Being careful, tighten alternately and gradually four screws.
2. Figure shows V polarization.
3. Be careful not to damage the O-ring (Antenna).
4. The tightening torque is 4.0 Nm 10%.
O-ring
Hole for guide pin
ANDREW VHLP Type Bracket
ODU (6-11 GHz) ODU (13-42 GHz)
MOUNTING ODU 5-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Notes
1. Figure shows V polarization.
2. Be careful not to damage the O-ring (Antenna).
3. The tightening torque is 4.0 Nm 10%.
RFS SB1 Type Bracket
O-ring
Hole for guide pin
ODU (6-11 GHz) ODU (13-42 GHz)
Note Set the ODU to the bracket after
polarization of the ODU is confirmed.
O-ring
RFS C-Mount Type Bracket
Hole for guide pin
ODU (6-11 GHz) ODU (13-42 GHz)
5-10 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Insert guide pin on the hole of bracket to set the position of screws,
Caution Align flanges on antenna and ODU correctly, and fix the ODU
with four screws.
5 Fix the ODU to the bracket with four screws.
Note Tightening torque is 4.0 Nm 10%.
Guide pin
ODU
ODU flange
Antenna flange
Antenna
Screws
Screws
Screws
Screws
ODU (6-11 GHz)
ODU (13-42 GHz)
MOUNTING ODU 5-11
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Note Antenna separation (S) is given by path calculation depending on the
system parameter.
1+1 SD System
Pole
(S)
Member of tower
1+0 System
Member of tower
Pole
No.1 ODU
No.2 ODU
ODU
ODU (6-11 GHz)
1+0 System
Member of tower
Pole
ODU
ODU (13-42 GHz)
1+1 SD System
ODU (6-11 GHz)
ODU (13-42 GHz)
Pole
(S)
Member of tower
No.2 ODU
No.1 ODU
5-12 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 5-1 Change of Polarization of Antenna
(1) ODU Direct Mounting Type Antenna (ANDREW Example #1)
Notes
1. The details are referred to the installation manual which is attached to
the antenna. The installation or removal of the antenna requires qualified
experienced personnel.
2. The antenna is set to V-polarization when shipped from the factory.
1 Keep the antenna stand horizontally,
2 If you change to H polarization, loosen the four screws with the hexagonal key
wrench and then rotate the Transition hub of feed, keeping the antenna stand
horizontal,
Note Do not remove the screw complete from the screw hole.
Hold the feed horn with hand.
Transition hub
2 screws
2 screws
MOUNTING ODU 5-13
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Holding the feed with hand, rotate the feed 90 degrees,
Check that the aperture part of the Transition hub is rotated 90 degrees, then fix it
with the screws that were loosened in Step 2,
4 Check that the aperture part of the Transition hub is rotated 90 degrees, then fix it
with the screws that were loosened in Step 2.
Note When a large and a small gasket are included in the antenna package.
Please use the large one. (The small gasket is not used in antenna
mount.)
(2) ODU Direct Mounting Type Antenna (ANDREW Example #2)
Notes
1. The details are referred to the installation manual which is attached to
the antenna. The installation or removal of the antenna requires qualified
experienced personnel.
2. The antenna is set to V-polarization when shipped from the factory.
1 Keep the antenna stand horizontally,
2 Loosen six screws with Allen wrench until transition can rotate freely,
Notes
1. Do not remove the screw complete from the screw hole.
2. Because of the screwtight is applied, the strength to loosen screw is
necessary.
Polarization
V
Polarization
H
Top Top
5-14 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Rotate the transition hub 90 degrees until timing pin locates in timing concavity.
Tighten six screws when transition hub is located. (Tightening torque is 5.0 Nm
10%.)
(3) ODU Direct Mounting Type Antenna (RFS Example)
Notes
1. The details are referred to the installation manual which is attached to
the antenna. The installation or removal of the antenna requires qualified
experienced personnel.
2. The antenna is set to V-polarization when shipped from the factory.

Vertical Polarized Application Horizontally Polarized Application
Transition hub
Transition hub
Timing pin Transition hub
RFS SB1
1. Unscrew the 4 screws M3 at the refined
steel ring,
2. Hold the feed tightly at the waveguide,
3. Rotate carefully the feed 90 degrees,
4. Mount the feed to the refined steel ring
and lock the 4 screws M3.
1. Loosen the 4 screws M3,
2. Hold the feed tightly at the waveguide,
3. Rotate the casting plate carefully the
feed 90 degrees,
4. Lock the 4 screws M3.
RFS C-mount
Drain plug
Drain plug
MOUNTING ODU 5-15
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4 screws (M3)
Polarization V Polarization H
Antenna top
Vertical
Horizontal
5-16 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 5-2 Change of Polarization of ODU
1 When vertical polarization is required, rotate the ODU so as to go up the lug
marked with V.
2 When horizontal polarization is required, remove the guide pin fixed on the lug
marked with V.
3 Screw in the guide pin removed in Step 2 to the screw hole of the lug marked
with H.
4 Rotate the ODU so as to go up the lug marked with H.

Notes
1. When the ODU is mounted on the NEC Hybrid/Coupler, only V
polarization is applied.
2. When the waveguide or coaxial cable is connected between the ODU
and antenna, the ODU in V polarization for up position is recommended
for installation.
Guide pin
V-marked Lug
Guide pin
H-marked Lug
V-marked Lug
UP
V Polarization
H-marked Lug
UP
H Polarization
FG
IFL MON
RX LEV
F
G
IF
L
M
O
N
R
X

L
E
V
V/H Polarization Conversion
6-11 GHz ODU
MOUNTING ODU 5-17
iPASOLINK 1000: INSTALLATION NWD-118789-04E
V Polarization
-
I R
V-marked Lug
Guide pin
UP
-
I
R
H-marked Lug Guide pin
UP
H Polarization
V/H Polarization Conversion
13-42 GHz ODU
5-18 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.1.2 With Hybrid/Coupler
This section explains the antenna direct mounting type ODU installation with
Hybrid/Coupler.
Mounting
Note The details are referred to the installation manual which is attached to
the antenna.
ANDREW VHLP Type Bracket
Mounting hole for
Hybrid/Coupler
Hole for guide pin
Note The tightening torque is 4.0 Nm 10%.
Be careful not to damage the O-ring (Antenna).
O-ring
Hole for guide pin
O-ring
RFS SB1 Type Bracket
RFS C-mount type bracket
Mounting hole for
Hybrid/Coupler
O-ring
Hole for guide pin
Mounting hole for
Hybrid/Coupler
Note The tightening torque is 4.0 Nm 10%.
Be careful not to damage the O-ring (Antenna).
MOUNTING ODU 5-19
iPASOLINK 1000: INSTALLATION NWD-118789-04E
[A] 10-42 GHz Hybrid/Coupler
1 Fix the bracket and handle to the Hybrid/Coupler,
Note Tightening torque is 3.0 Nm 10%.
2 Check the polarization and install the Hybrid/Coupler to the antenna by
tightening the M6 screws (four locations),
.
Notes
1. Be careful not to damage the O-ring.
2. Tightening torque is 4.0 Nm 10%.
Hybrid/Coupler
Handle
M5 head cap screw
M5x12 (10ea)
Bracket
PUSH
ANT
O-ring
Hybrid/Coupler
Flat washer M6 screw
Guide pin
Short plate
O-ring
ODU port
5-20 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Insert the O-rings to the two ODU ports of the Hybrid/Coupler,
4 Install the two ODUs with hex screws (four locations) using the Allen key
wrench.
Note Be careful not to damage the O-rings (Hybrid/Coupler).
For 10/11 GHz ODU
Note Tightening torque is 4.0 Nm 10%.
O-ring
ODU
ODU
O-ring
ODU
MOUNTING ODU 5-21
iPASOLINK 1000: INSTALLATION NWD-118789-04E
For 26-42 GHz ODU
Note Tightening torque is 4.0 Nm 10%.
O-ring
ODU
O-ring
ODU
ODU
ODU
ODU
5-22 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Demounting from Hybrid/Coupler
1 Loosen the four (or six) bolts fixed the ODU,
2 Then demount the ODU.
Note When demounting the ODU from Hybrid/Coupler, mount the attached
SHORT PLATE to the demounted port of the Hybrid/Coupler to avoid RF
power leaking from the hybrid/coupler and for waterproofing.
Note Tightening torque is 3.0 Nm 10%.
Mounting short plate to the
ODU port
Mounting hole for
short plate
Short plate
MOUNTING ODU 5-23
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Change of Polarization of Hybrid/Coupler
Note The hybrid/coupler is set to V-polarization when shipped from the
factory.
1 If you change the polarization from V to H, loosen two screws, rotate the
transition hub and put it to the Hybrid/Coupler,
Note There are two types Hybrid/Coupler. One uses two pieces transition
hubs and another uses one piece.
2 Then fix it with the two screws that were loosened in Step 1.
Transition
hub
V Polarization
Guide pin
Hybrid/Coupler
V Polarization H Polarization
Two Pieces Transition Hub Type
H Polarization
V Polarization
One Piece Transition Hub Type
Cross-recessed
head machine screw
M2.6 (2ea)
Cross-recessed
head machine screw
M2.6 (2ea)
5-24 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
[B] 7/8 GHz Hybrid
This Hybrid/coupler is designed to be attached to 0.6 to 1.8 m antennas with interface
for direct mounting of ODU.
1 Hybrid assembly
Note Tightening torque is 3.0 Nm 10%.
2 Polarization coarse alignment
Support
Spring washer M5 (8ea.)
Hexagon socket
head cap screw
M5 x 14 (8ea.)
Hybrid
V Polarization H Polarization
Cross-recessed
Head machine screw
M2.6 (2ea.)
(Shipment condition)
MOUNTING ODU 5-25
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Installation to antenna
Note Tightening torque is 4.0 Nm 10%.
4 Attachment of main ODU
Note Tightening torque is 4.0 Nm 10%.
Flat washer M6 (4ea.)
Hexagon socket
head cap screw
M6 x 20 (4ea.)
Spring washer M6 (4ea.)
Short plate
In case of removing ODU,
attach this short plate to
the ODU port.
Attachment of Short Plate
Hybrid
Antenna
equally and carefully by
Tighten the each screw
wrench at diagonal
position.
O-ring
Packing (Supplied by antenna)
Connection Part Details
Top View
NEC ODU
(Main ODU)
Hexagon socket
head cap screw M6
(Supplied by NEC
O-ring
(Packing)
V direction of ODU
with ODU)
O-ring (Packing)
5-26 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5 Attachment of standby ODU
SS: Stainless steel
Table 5-2 Hybrid Parts List
No. Parts Name Qty
1 Hybrid 1
2 Support 1
3 O-ring 2
4 M5 x 14 Hexagon Socket Head Cap Screw (SS) 8
5 M5 Spring Washer (SS) 8
6 M6 x 20 Hexagon Socket Head Cap Screw (SS) 4
7 M6 Flat Washer (SS) 4
8 M6 Spring Washer (SS) 4
V direction of ODU
NEC ODU
(Main ODU)
O-ring
(Packing)
NEC ODU
(Standby ODU)
Top View
MOUNTING ODU 5-27
iPASOLINK 1000: INSTALLATION NWD-118789-04E
[C] 7/8 GHz Coupler
This Hybrid/coupler is designed to be attached to 0.6 to 1.8 m antennas with interface
for direct mounting of ODU.
1 Coupler assembly,
Note Tightening torque is 3.0 Nm 10%.
2 Polarization coarse alignment
Support
Spring washer M5 (8ea.)
Hexagon socket
head cap screw
M5 x 14 (8ea.)
Coupler
V Polarization H Polarization
Cross-recessed
Head machine screw
M2.6 (2ea.)
(Shipment condition)
5-28 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Installation to antenna
Note Tightening torque is 4.0 Nm 10%.
4 Attachment of main ODU
Note Tightening torque is 4.0 Nm 10%.
Packing (Supplied by antenna)
Flat washer M6 (4ea.)
Hexagon socket
head cap screw
M6 x 20 (4ea.)
Spring washer M6 (4ea.)
Short plate
In case of removing ODU,
attach this short plate t
the ODU port.
Attachment of Short Plate
Coupler
Antenna
equally and carefully by
Tighten the each screw
wrench at diagonal
position.
O-ring
Connection Part Details
Top View
NEC ODU
(Main ODU)
Hexagon socket
head cap screw M6
(Supplied by NEC
O-ring
(Packing)
V direction of ODU
with ODU)
O-ring (Packing)
MOUNTING ODU 5-29
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5 Attachment of standby ODU
SS: Stainless steel
Table 5-3 Coupler Parts List
No. Parts Name Qty
1 Coupler 1
2 Support 1
3 O-ring 2
4 M5 x 14 Hexagon Socket Head Cap Screw (SS) 8
5 M5 Spring Washer (SS) 8
6 M6 x 20 Hexagon Socket Head Cap Screw (SS) 4
7 M6 Flat Washer (SS) 4
8 M6 Spring Washer (SS) 4
V direction of ODU
NEC ODU
(Main ODU)
O-ring
(Packing)
NEC ODU
(Standby ODU)
Top View
5-30 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
[D] 13/15 GHz Hybrid, 15 GHz Coupler
This Hybrid/coupler is designed to be attached to 0.2 to 1.8 m antennas with interface
for direct mounting of ODU.
1 Hybrid/Coupler assembly
Note Tightening torque is 3.0 Nm 10%.
2 Polarization coarse alignment
Support
Spring washer M5 (8ea.)
Hexagon socket
head cap screw
M5 x 12 (8ea.)
Hybrid/Coupler
V Polarization H Polarization
Cross-recessed
head machine screw
M2.6 (2ea.)
MOUNTING ODU 5-31
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Installation to antenna
Note Tightening torque is 4.0 Nm 10%.
4 Attachment of main ODU
Note Tightening torque is 4.0 Nm 10%.
Packing (Supplied by Antenna)
Flat washer M6 (4ea.)
Hexagon socket
head cap screw
M6 x 20 (4ea.)
Spring washer M6 (4ea.)
Short plate
In case of removing ODU,
attach this short plate t
the ODU port.
Attachment of Short Plate
Hybrid/Coupler
Antenna
equally and carefully by
Tighten the each screw
wrench at diagonal
position.
O-ring
Connection part details
Top View
NEC ODU
(Main ODU)
Hexagon socket
head cap screw M6
(Supplied by NEC
O-ring
(Packing)
V direction of ODU
with ODU)
O-ring
(Packing)
5-32 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5 Attachment of standby ODU
SS: Stainless steel
Table 5-4 Hybrid/Coupler Parts List
No. Parts Name Qty
1 Hybrid/Coupler 1
2 Support 1
3 O-ring 2
4 M5 x 12 Hexagon Socket Head Cap Screw (SS) 8
5 M5 Spring Washer (SS) 8
6 M6 x 20 Hexagon Socket Head Cap Screw (SS) 4
7 M6 Flat Washer (SS) 4
8 M6 Spring Washer (SS) 4
V direction of ODU
NEC ODU
(Main ODU)
O-ring
(Packing)
NEC ODU
(Standby ODU)
Top View
MOUNTING ODU 5-33
iPASOLINK 1000: INSTALLATION NWD-118789-04E
[E] 18/23 GHz Hybrid
This Hybrid is designed to be attached to 0.2 to 1.8 m antennas with interface for
direct mounting of ODU.
1 Hybrid assembly
Note Tightening torque is 3.0 Nm 10%
2 Polarization coarse alignment
Support
Spring washer M5 (8ea.)
Hexagon socket
head cap screw
M5 x 12 (8ea.)
Hybrid
V Polarization H Polarization
Cross-recessed
head machine screw
M2.6 (2ea.)
5-34 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Installation to antenna
Note Tightening torque is 4.0 Nm 10%.
4 Attachment of main ODU
Note Tightening torque is 4.0 Nm 10%.
O-ring
Antenna
Packing (Supplied by Antenna)
Flat washer M6 (4ea.)
Hexagon socket
head cap screw
M6 x 20 (4ea.)
Spring washer M6 (4ea.)
Short plate
In case of removing ODU,
attach this short plate t
the ODU port.
Attachment of Short Plate
Hybrid
equally and carefully by
Tighten the each screw
wrench at diagonal
position.
O-ring (Packing)
Connection Part Details
Top View
NEC ODU
(Main ODU)
Hexagon socket
head cap screw M6
(Supplied by NEC
O-ring
(Packing)
V direction of ODU
with ODU)
MOUNTING ODU 5-35
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5 Attachment of standby ODU
SS: Stainless steel
Table 5-5 Hybrid Parts List
No. Parts Name Qty
1 Hybrid 1
2 Support 1
3 O-ring 2
4 M5 x 12 Hexagon Socket Head Cap Screw (SS) 8
5 M5 Spring Washer (SS) 8
6 M6 x 20 Hexagon Socket Head Cap Screw (SS) 4
7 M6 Flat Washer (SS) 4
8 M6 Spring Washer (SS) 4
V direction of ODU
NEC ODU
(Main ODU)
O-ring
(Packing)
NEC ODU
(Standby ODU)
Top View
5-36 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.1.3 With TX Span Attenuator
This section explains the antenna direct mounting type ODU installation with TX
Span Attenuator (TX SPAN ATT).
Mounting
1 Check the polarization of the antenna connection unit of the TX ATT (Refer to
Change of Polarization of TX ATT to be hereinafter described.),
2 Fix the TX ATT to the antenna by tightening the M6 screws (four locations),
3 Insert the O-rings to port of the ODU,
4 Fix the ODU with hex screws (four locations) using the hexagonal key wrench.
Note Be careful not to damage the O-rings (TX ATT).
Antenna connection unit
TX ATT
Antenna
Guide pin
TX ATT
Flat washer M6 (4ea)
Packing (Supplied by antenna)
Installation to Antenna
1 2
3 4
Note Tightening torque (M6) is 4.0 Nm 10%.
Hexagon socket
head cap screw
M6 x 30 (4ea)
32/42 GHz Band ODU Mounting with TX SPAN ATT (1/2)
38A
Tighten the each
screw equally and
carefully by wrench
at diagonal position.
MOUNTING ODU 5-37
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Attachment of ODU
Hexagon socket
head cap screw M6
(Supplied by NEC with ODU)
O-ring
(Packing)
O-ring
(Packing)
ODU connection unit
ODU
Top View
Side View
TX ATT
ODU
Antenna
TOP
TX ATT
ODU should be attached
by turning V up.
Note Tightening torque is 4.0 Nm 10%.
32/42 GHz Band ODU Mounting with TX SPAN ATT (2/2)
38A
5-38 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Change of Polarization of TX SPAN ATT
Note The TX ATT is set to V-polarization when shipped from the factory.
1 If you change to H polarization, loosen two screws, rotate the antenna connection
unit and put the TX ATT horizontally,
2 Check that aperture of the connection unit is rotated as shown below, then fix it
with the two screws that were loosened in Step 1.
TX ATT
Antenna
connection unit
V Polarization
Guide pin
Cross-recessed
Head machine screw
M2.6 (2ea)
Plate-1
H Polarization V Polarization
32/42 GHz Band TX SPAN ATT Polarization Change
Plate-2
MOUNTING ODU 5-39
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5.1.4 With Ortho-Mode Transducer
This section explains the antenna direct mounting type ODU installation with Ortho-
Mode Transducer (OMT).
There are two types of O-rings for antenna mounting to the OMT depending on the
frequency band.
Caution Do not apply silicon grease to O-ring.
Note O-ring size is different with frequency band as follows:
Position of large size
O-ring
For Antenna Direct Mounting
RFS Antenna
Position of large size
O-ring
For Antenna Direct Mounting
ANDREW Antenna
3
2
m
m
3
5
m
m
Large Size O-ring for Antenna Direct Mounting
26-42 GHz Band 13-23 GHz Band
4

m
m
4

m
m
4
0
m
m
10-11 GHz Band
4

m
m
13-23 GHz Band 42 GHz Band
1
5
.
6
m
m
Small Size O-ring for Waveguide Connection
1
0
.
8
m
m
1
.
8

m
m
1
.
8

m
m
5-40 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
For the antenna direct mounting of the ODU, following OMT is used.
Cautions
1. For connecting the OMT to the antenna, the circular type waveguide flange
of the antenna is applied to the system. When the V/H flange is mounted to
the antenna, it must be changed to a circular type.
2. When mounting the ODU to the OMT, confirm the polarization for main
master and sub master ODU. The installation of the corresponding ODUs in
the opposite station must have the same polarization in order to make into
line main master and sub master MODEMs.
1 Fix the bracket and handle to the OMT,
Note Tightening torque is 3.0 Nm 10%.
Frequency
Band
Frequency
Range (GHz)
Interface WG Inner
Dia. (mm)
(ANT Side)
Interface
(ODU Side)
11 G 10.4 11.7 GHz 18.0 NEC Original
13 G 12.75 13.25 GHz 15.0
15 G 14.5 15.35 GHz 13.5
18 G 17.7 19.7 GHz 10.5
23 G 21.2 23.6 GHz 9.0
26 G 24.5 26.5 GHz 8.0
28 G 27.5 29.5 GHz 7.0
32 G 31.8 33.4 GHz 6.5
38 G 37 39.5 GHz 5.5
42 G 40.5 43.5 GHz 4.8
M5 head cap screw
MOUNTING ODU 5-41
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Fix the OMT to the antenna by tightening them with M6 screws (four locations),

Notes
1. Be careful not to damage the O-ring.
2. Tightening torque is 4.0 Nm 10%.
3 Loosen the two screws and move the short plate if it is fixed to the ODU port (see
figure in Step 9),
4 Set the two ODUs to vertical polarization for OMT mounting. If the guide pin
behind the plate marked H is mounted, remove the guide pin,
Note The ODU should be attached by turning the plate marked V up position
for both main master ODU and sub master ODU.
5 Insert the guide pin removed in Step 4 behind the plate marked V,
Note Remove the protection metallic plate covering the waveguide hole on
ODU.
ANT
Flat washer M6
Guide pin
O-ring
Short plate
O-ring
M6 screw
ODU port
Guide pin
Plate marked with V
5-42 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
6 Insert the O-rings to the two ODU ports of the OMT (see figure in Step 9),
7 Insert the guide pin into the hole of the OMT and set the position of screws,
8 Confirm which polarization is applied to the master ODU.
Check the indication of polarization on the upper side of OMT,
Main Master Sub Master
Plate marked with V
UP
FG
IFL MON
RX LEV
FG
IFL MON
RX LEV
ODU (10/11 GHz)
Main Master Sub Master
Plate marked with V
UP
-
I R
-
I R
ODU (13-42 GHz)
Guide pin
MOUNTING ODU 5-43
iPASOLINK 1000: INSTALLATION NWD-118789-04E
9 Fix the two ODUs with hex screws (four locations) using the hexagonal key
wrench.
Note Be careful not to damage the O-rings.
H Polarization side
V Polarization side
Note Tightening torque is 4.0 Nm 10%.
ODU (10/11 GHz)
O-ring
ODU
Note Tightening torque is 4.0 Nm 10%.
ODU (13-42 GHz)
Hex screw
Hex screw
Hex screw
ODU
ODU
ODU
Hex screw
O-ring
ODU
H Polarization side
V Polarization side
O-ring
ODU
O-ring
5-44 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Cautions
1. Tighten all screws with lighter torque at first, then full torque as specified.
2. When either ODU is demounting for ODU replacing or other reasons, fix the
attached short plate to the demounted port of the OMT to avoid leaking of
RF power from the OMT and for waterproof.
3. To avoid occurrence of bit errors due to microphonic properties, when
installing the sub master ODU, protect the main master ODU from
mechanical knocks.

Note Tightening torque is 3.0 Nm 10%.
Fixed short plate
to ODU port
Fixing hole for
short plate
Short plate
MOUNTING ODU 5-45
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5.2 Feeder Connection
5.2.1 For Coaxial Cable Connection
6/7/8GHz ODU MOUNTING BRACKET INSTALLATION
This mounting bracket is designed in order to install 6/7/8 GHz ODU with N-type
connector or waveguide interface to a pole. The diameter of the pole is from 48.5 to
114.3 millimeters.


SS: Stainless steel
Note Tightening torque is 4 Nm 10% (M6 screw).
Tightening torque is 11 Nm 10% (M8 screw).
Table 5-6 Mounting Bracket Parts List
Item Description Qty
1 Bracket 1
2 Holder-1 (with Two M6 Taps) 2
3 Holder-2 2
4 M8 Stud Bolt (SS) 4
5 M8 Hexagon Nut (SS) 20
6 M8 Flat Washer (SS) 8
7 M616 Hexagon Socket Head Screw (SS) 4
8 M6 Spring lock Washer (SS) 4
9 M6 Flat Washer (SS) 4
10 Cap 4
11 Band (Cable Clamp) 2
Mounting Bracket
5-46 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
1 A nut is assembled to a stud bolt until a nut has come to a complete stop,
Standard Installation Reverse Installation
Stud bolt M8
Hexagon nut M8
Hexagon nut M8 (4 ea)
Stud bolt M8 (2 ea)
Fixed nut
Approx. 56 mm
Holder-1
Flat washer M8 (2 ea)
Note Tightening torque
is 11 Nm 10%.
Assembly of the Holder-1 (2 sets)
2 taps M6
MOUNTING ODU 5-47
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Fix the two holder-1 to the bracket at four bolts,
3 Mount the bracket to the pole, point to the opposite station and tighten it with
four stud bolts,
Note Since a bolt projects from a holder when a pole diameter is small, please
attach the cap to a bolt end.
Assembly of the Bracket
Holder-1 assembly
Bracket
Flat washer M6 (4 ea)
Spring lock washer M6 (4 ea)
Hexagon socket head screw M616 (4 ea)
Note Tightening torque is 4
Nm 10%.
Pole (| 48.5 to 114.3 mm)
Note Tightening torque is
11 Nm 10%.
Holder-2 (2 ea)
A = B
A
B
Installation to the Pole
Holder
Bolt end
Cap (4 ea)
Hexagon nut M8 (8 ea)
Flat washer M8 (4 ea)
5-48 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Mount the ODU on to the bracket and tighten four bolts (M6) at upper and lower
parts of the ODU,
5 Connect the coaxial cable to the RF IN/OUT connector of the ODU,
6 Install the coaxial cables between the antenna and the ODU.
Notes
1. Fix the coaxial cable to the pole or member with band (cable ties) after
antenna orientation has been completed.
2. Wrap the coaxial cable connection points with a self-bonding tape for
waterproof. (The self-bonding tape shall be prepared by customer.)
Hexagon socket head screw M6
Attachment of the ODU
Note Tightening torque is
4 Nm 10%.
Right angle side
Top View
Connection of the Coaxial Cable Example
N-type connector
Band
Coaxial
cable
Antenna
Coaxial cable
Pole
ODU
MOUNTING ODU 5-49
iPASOLINK 1000: INSTALLATION NWD-118789-04E
5.2.2 For Waveguide Connection
10-42 GHz ODU MOUNTING BRACKET INSTALLATION
This mounting bracket is designed in order to install 10-42 GHz ODU with antenna
direct mount interface to a pole. The diameter of the pole is from 48.5 to 114.3
millimeters.
SS: Stainless steel
Note Tightening torque is 4 Nm 10% (M6 screw).
Tightening torque is 11 Nm 10% (M8 screw).
Table 5-7 Mounting Bracket Parts List
Item Description Qty
1 Bracket (with Adapter) 1
2 Holder-1 (with two M6 taps) 2
3 Holder-2 2
4 M8 Stud Bolt (SS) 4
5 M8 Hexagon Nut (SS) 20
6 M8 Flat Washer (SS) 8
7 M616 Hexagon Socket Head Screw (SS) 4
8 M6 Spring Lock Washer (SS) 4
9 M6 Flat Washer (SS) 4
10 Cap 4
11 O-Ring (for ODU) 1
12 O-Ring (for Waveguide) 1
13 Screw of Waveguide Connecting
for 10/11 GHz M414 Hexagon Head Screw with Washer (SS)
for 13/15 GHz M412 Hexagon Head Screw with Washer (SS)
for 18/23/26/28/32/42 GHz M310 Hexagon Head
Screw with Washer (SS)
8
4
4
Mounting Bracket
5-50 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION

1 A nut is assembled to a stud bolt until a nut has come to a complete stop,
Standard Installation Reverse Installation
Stud bolt M8
Hexagon nut M8
Hexagon nut M8 (4 ea)
Stud bolt M8 (2 ea)
Fixed nut
Approx. 56 mm
Holder-1
Flat washer M8 (2 ea)
Note Tightening torque is
12 Nm 10%.
Assembly of the Holder-1 (2 sets)
2 taps M6
MOUNTING ODU 5-51
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Fix the two holder-1 to the bracket at four bolts,
3 Mount the bracket to the pole, point to the opposite station and tighten it with
four stud bolts,

Assembly of the Bracket
Holder-1 assembly
Bracket (with adapter)
Flat washer M6 (4 ea)
Spring lock washer M6 (4 ea)
Hexagon socket head screw M616 (4 ea)
Note Tightening torque is
4 Nm 10%.
Pole (| 48.5 to 114.3 mm)
Flat washer M8 (4 ea)
Hexagon nut M8 (8 ea)
Note Tightening torque is
12 Nm 10%.
Holder-2 (2 ea)
A = B
A
B
Installation to the Pole
Holder
Bolt end
Cap (4 ea)
5-52 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Note Since a bolt projects from a Holder when a pole diameter is small, please
attach the cap to a bolt end.
4 Mount the ODU on to the bracket and tighten four bolts (M6) at upper and lower
parts of the ODU. Please equip the terminal area of ODU and adapter with O-
ring, and join together after that,
5 When the attachment screw of the ODU is hard, please loosen the fixed four
screw of adapter once,
6 Please adjust the position of adapter to compensate for attachment of ODU. Then
tighten four bolts (M6) of the ODU,
Hexagon socket head screw M6
Attachment of the ODU
Note Tightening torque is
4 Nm 10%.
Right angle side
Adapter
ODU
Adapter
O-ring (for ODU)
Top View
Loosen the fixed four screws Adapter
Bracket
MOUNTING ODU 5-53
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7 Connect the waveguide to the adapter of the mounting bracket,
8 Install the waveguide between the antenna and the ODU.
Table 5-8 Waveguide Flange Type
Frequency Band Adapter Waveguide
10/11 GHz PDR100 PDR100
13 GHz PBR120 UBR120
13/15 GHz PBR140 UBR140
18/23 GHz PBR220 UBR220
26 GHz PBR260 UBR260
28/32/42 GHz PBR320 UBR320
Connection of the Waveguide Example
Flexible waveguide
Antenna
Pole
ODU
Flexible waveguide
Flexible waveguide O-ring (for waveguide)
Screw of waveguide
connecting
5-54 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.2.3 For Waveguide Connection with Hybrid
18/23 GHz Hybrid (FI)
This Hybrid is designed to be connect to waveguide with interface for direct
mounting of ODU. (Waveguide flange type: Hybrid side-PBR220, Waveguide side-
UBR220.)
1 Hybrid assembly
Tightening Torque
M3 0.6 Nm 10%
M5 3.0 Nm 10%
M6 4.0 Nm 10%
PUSH Handle
Hexagon socket
head cap screw
M5 12 (10 ea)
Bracket
Hybrid
MOUNTING ODU 5-55
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Installation to pole mount
3 Attachment of main ODU
Hexagon head screw
M6 35 (4 ea)*
Case-1
Flat washer M6
(4 ea)*
Pole mount
Flat washer M6 (4 ea)*
Hexagon nut M6 (Double) (8 ea)*
Hybrid
Short plate
In case you remove ODU,
Please attach this Short plate
to the ODU port.
O-ring
Attachment of Short Plate
Note *: Supplied by pole mount.
ODU (Main ODU)
Pole mount
Hexagon socket head
cap screw M6
ODU should be attached by turning V up.
O-ring I/D |32
(Packing)
O-ring I/D |32
(Packing)
Connection Part Details
Top View
5-56 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Attachment of standby ODU
5 Connection of waveguide
ODU (Main ODU)
O-ring I/D |32
(Packing)
ODU (Standby ODU)
Pole mount
ODU should be attached by turning V up.
Top View
Hybrid
Flexible waveguide
Flange type UBR220
Pole mount
O-ring I/D |32
(Packing)
Hexagon head screw
with washer M310 (4 ea)
Hybrid
Waveguide flange
Flange type PBR220
Do not remove.
*
Caution*: Please connect the flexible
waveguide in the same
direction as Hybrid.
MOUNTING ODU 5-57
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Caution Be careful not to damage the Hybrid. Connection part will be
damaged if excessive power is applied to the Hybrid by
waveguide.
*: Supplied by pole mount.
SS: Stainless steel
6 Installation to mounting bracket
Table 5-9 Hybrid (Fl) Parts List (for Mounting Bracket)
No. Parts Name Qty
1 Hybrid (Waveguide Flange Interface Type) 1
2 Bracket 2
3 Handle 1
4 O-ring Inner Dia. |32 (for ODU) 2
5 O-ring Inner Dia. |15.6 (for Waveguide) 1
6 M5 12 Hexagon Socket Head Cap Screw (SS) 14 (4 part for spare.)
7 M3 10 Hexagon Head Screw With Washer (SS) 4
* M6 35 Hexagon Socket Head Cap Screw, Nut, Washer Set (SS) 4
Case-2
Mounting bracket
Short plate
In case you remove ODU,
Please attach this Short
plate to the ODU port.
O-ring
Attachment of short plate
Hybrid
Hexagon head screw M6 20 (4 ea)
Flat washer M6 (4 ea)
5-58 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7 Attachment of main ODU
8 Attachment of standby ODU
Mounting bracket
O-ring I/D |32
(Packing)
Connection part details
ODU (Main ODU)
Hexagon socket head
cap screw M6
O-ring I/D |32
(Packing)
ODU should be attached
by turning V up.
Top View
Mounting bracket
ODU (Main ODU)
O-ring I/D |32
(Packing)
ODU (Standby ODU)
ODU should be attached by turning V up.
Top View
MOUNTING ODU 5-59
iPASOLINK 1000: INSTALLATION NWD-118789-04E
9 Connection of waveguide
SS: Stainless steel
Table 5-10 Hybrid (Fl) Parts List (for Mounting Bracket)
No. Parts Name Qty
1 Hybrid (Waveguide Flange Interface Type) 1
2 Bracket 2
3 Handle 1
4 O-ring Inner Dia. |32 (for ODU) 2
5 O-ring Inner Dia. |15.6 (for Waveguide) 1
6 M5 12 Hexagon Socket Head Cap Screw (SS) 14 (4 part for spare.)
7 M6 20 Hexagon Socket Head Cap Screw (SS) 4
8 M6 Flat Washer (SS) 4
9 M3 10 Hexagon Head Screw With Washer (SS) 4
Hybrid
Waveguide flange
Flange type PBR220
Do not remove.
*
Mounting bracket
O-ring I/D |15.6
(Packing)
Hexagon head screw
with washer M3 10
(4 ea)
Flexible waveguide
Flange type UBR220
Caution*: Please connect the flexible
waveguide in the same
direction as Hybrid.
5-60 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.3 Other Mounting
5.3.1 Wall Mounting
For the antenna direct mounting type ODU, wall mounting installation is explained in
following procedure.
1 Using a center punch and hammer, mark the drilling holes for the ODU wall
mount bracket. Dimensions are shown below,
2 Using an electric drill for concrete, drill the guide holes,
3 Change the concrete drill to enlarge the holes and drill the anchor bolt holes,
2
1
1
Unit: mm
Wall
L
L
D
M10
L
D
MOUNTING ODU 5-61
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4 Remove debris from the specified hole and insert a plug-bolt into it,

5 Make sure to insert the plug-bolt fully,
6 Tighten hardly the bolt using a wrench or monkey wrench,
Note Anchor bolts of M10 bolt shall be prepared by the customer.

7 Loosen the bolt and remove it,

Anchor bolt
Bolt
Washer
5-62 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
8 Fix the ODU wall mounting bracket to the wall with the six bolts (M6) of the
anchor volt,
Note The bolt, flat washer and spring washer are the anchor bolt.
9 Mount the ODU onto the bracket and fix the ODU using the four bolts (M6) on
the ODU,
Note The tightening torque is 4.0 Nm 10%.
Flat washer*
Spring washer*
Bolt*
Flange adaptor
Guide pin
(V)
Transducer Transducer
Guide pin
(V)
ODU (13-42 GHz) ODU (10/11 GHz)
MOUNTING ODU 5-63
iPASOLINK 1000: INSTALLATION NWD-118789-04E
10 Connect the wave guide to the transducer for the ODU.
Notes
1. Tightening torque is 1.4 Nm 10% (up to 15 GHz).
Tightening torque is 0.6 Nm 10% (18 GHz or higher).
2. Be careful not to damage the O-ring.
Refer to 5.2.2 ODU Mounting for Waveguide Connection.
Washer
O-ring
Bolt (M4)
Spring washer
ODU 10/11 GHz)
Waveguide
A
Washer
O-ring
Bolt(M4)
Spring washer
ODU 13-42 GHz)
Waveguide
For 13-42 GHz
Details of A
For 10/11 GHz
A
5-64 MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.3.2 Rack Mounting
For the antenna direct mounting type ODU, rack mounting installation is explained in
following procedure.
1 Fix the ODU rack mounting bracket into the 19-inch rack using the six fixing
bolts,
2 Mount the ODU onto the bracket and tighten the four fixing bolts (M6) on the
ODU,
Note The tightening torque is 4.0 Nm 10%.
ODU mounting bracket
Bolt
Spring washer
Flat washer
19-inch rack
Flange adaptor
ODU
Guide pin
MOUNTING ODU 5-65
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Connect the wave guide to the transducer for the ODU.
Notes
* M4: Up to 15 GHz.
M3: 18 GHz or higher.
1. Tightening torque is 1.4 Nm 10% (up to 15 GHz).
Tightening torque is 0.6 Nm 10% (18 GHz or higher).
2. Be careful not to damage the O-ring.
Refer to 5.2.2 ODU Mounting for Waveguide Connection.
Washer
O-ring
Waveguide
Bolt*
Spring washer
ODU
A
For 13-42 GHz
Details of A
For 10/11 GHz
5-66/END MOUNTING ODU
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5.4 Hybrid Combiner Installation
When you attach two Hybrids to one dual pole antenna, for 1+1 or 2(1+1) system in
6/7/8 GHz rotate the antenna 90 degree counter clockwise, as shown below, to avoid
hitting the hybrids to the antenna pole and its structures if necessary.
.
WG flange
To ODU
To ODU
Rotate counter
clockwise 90
degrees.
LOW LOSS cable
ADJUSTING CABLE ENDS 6-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
6. ADJUSTING CABLE ENDS
Following provides the list of tools, materials and the method for cable termination.
The applicable cables are listed in Table 6-1.
Notes
1. For the 1+1 system, the difference between the No.1 channel I/F cable
length and the No.2 channel I/F cable length should be within 100 m.
(differential absolute delay time: within 500 ns)
2. When the N (Male) straight connector is attached to the I/F cable, use of
the TNC (Male) - N (Female) (NJ-TNCP-LA) L-angle adapter is needed
to connect to the IDU.
3. Use shielded cables which are connected to the D-Sub/RJ-45 connector
to suppress interference from affecting the signal and to reduce
electromagnetic radiation which may interfere with other signal cables.
Table 6-1 List of Applicable Cable
Applicable Cable Connector Type Model# Procedure#
5D Coaxial
Cable
for IDU TNC-P L-angle TNC150(R0) Procedure 6-1
for IDU TNC-P L-angle 300PTR-C-NC Procedure 6-2
for IDU TNC-P L-angle TNC156(R0) Procedure 6-3
for ODU N-P L-angle 300PNR-C-NC Procedure 6-4
for ODU N-P Straight 300PNM-C-NC Procedure 6-5
for ODU N-P Straight N435(R0) Procedure 6-6
8D Coaxial
Cable
for IDU TNC-P L-angle TNC141(R0) Procedure 6-7
for ODU N-P L-angle N-LP-8DFB(B) Procedure 6-8
for ODU N-P Straight N416(R0) Procedure 6-9
Other Cables for power supply AMP Housing &
socket contacts
AMP: 1-178288-4 or
DK-3100S-04R
Procedure 6-10
for 120 ohms
balanced signal
D-sub Crimping --- Procedure 6-11
for auxiliary signal D-sub High Density --- Procedure 6-12
6-2 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
The necessary tools and materials are summarized in Table 6-2.
Table 6-2 Tools and Materials List
No. Name Remarks
1 Knife
For IF coaxial connector
2 Measure/Ruler
3 Cutter
4 Nipper
5 File
6 Spanner (14 mm, 16 mm)
7 Torque spanner (14 mm, 15 mm, 16 mm)
8 Clearance gauge
9 Comb
10 Tweezers
11 Scissors
12 Hand Crimping Tool
91558-1 For power supply connector
TC-CD-111
TC-CD-112
For D-Sub connector
09 88 999 0596 For D-Sub high density connector
ADJUSTING CABLE ENDS 6-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
6.1 5D Coaxial Cable
Procedure 6-1 TNC-P Connector used for IDU IF IN/OUT (L-angle: TNC150(R0))
1 Inset parts, remove cable jacket:
(1) Inset the clamp nut as shown below.
(2) Remove the cable jacket for 8 mm to the end.
Note Ensure not to damage the braided wires.
Tools
knife, cutter, nipper, tweezers, file, measure,
clearance gauge, etc.
spanner, torque spanner 14 mm
Tools
knife
cutter
measure, etc.
Outlines of parts [Applicable cable: 5D-FB-E]
Cable jacket Aluminum tape
Braided wire
Insulator
Center conductor
Connector body Clamp Clamp nut
Cable
Clamp nut
(8 mm)
*Cut the jacket edge squarely.
6-4 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2 Inset parts:
(1) Inset the clamp as shown below.
(2) Turn the braided wires back to the clamp side.
Clamp
Bad Example
The braids are uneven.
Braided wire
Insulator
Aluminium tape
Center conductor
ADJUSTING CABLE ENDS 6-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Remove braided wires and insulator:
(1) Cut the insulator and an aluminium tape along the end face of braided wires
that are turned up.
Note Ensure not to damage the braided wires and the center conductor.
Aluminium tape
Insulator
Center conductor
6-6 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
(2) Cut the braided wires according to a flange of clamp.
Tools
cutter
nipper
2)
Center conductor
1)
Flange
Braided wire
Flange
Aluminium tape
Center conductor
2)
1)
ADJUSTING CABLE ENDS 6-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4 Trim the center conductor:
(1) Remove the center conductor as shown below.
(2) Chamfer the center conductor.
Note Ensure not to damage the center conductor (burr, etc.).
Tools
nipper
file, etc.
Center conductor
1 mm
6 mm 1
Center conductor
6-8 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
5 Assemble connector:
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until it stops.
(2) Secure the connection to the torque value of 9 to 11 Nm.
(Refer to Steps (a) through (e).)
(a) Hold the cable and connector body.
Connector body
Clamp nut
ADJUSTING CABLE ENDS 6-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(b) Secure the clamp nut only by fingers.
(c) Hold the connector body by the spanner.
(d) Hold the cable.
* Keep holding the cable.
Do not rotate connector body.
6-10 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
(e) Set a torque spanner.
Secure the clamp nut only by the torque spanner.
Secure the connection to the torque value of 9 to 11 Nm.
Notes
1. Ensure not to put chips or shreds that are off from the braided wires into
the inner side of the central conductor and the connector body.
2. Do not rotate the cable or connector body alone; Rotate the clamp nut
attachment.
Tools
spanner (14 mm)
torque spanner (14 mm)
clearance gauge, measure
Holding only
14 mm 9-11 Nm 14 mm
ADJUSTING CABLE ENDS 6-11
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Procedure 6-2 TNC-P Connector used for IDU IF IN/OUT (L-angle: 300PTR-C-NC)
1 Remove the cable jacket:
Remove the cable jacket for 6.5 mm to the end, and expose the braided wires.
Note Ensure not to damage the braided wires.
2 Trim the braided wires 1
(1) Fold the braided wire around jacket.
(2) Remove the insulator for 5.0 mm to the end.
(3) Cut off the surplus of insulator/tape from the center conductor.
Note Ensure not to damage the center conductor.
Tools
knife, cutter, nipper, tweezers, file, comb,
measure, clearance gauge, etc.
spanner, torque spanner; 16 mm, 15 mm
Tools
knife
cutter
measure, etc.
[Applicable cable: 5D-FB-E]
Outlines of parts
Cable jacket
Aluminium tape
Braided wire Insulator
Center conductor
Connector body Parts A Parts B
A
B
6.5 mm
6-12 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Inset parts:
Twist the braided wires at the end and make them thinner.
As revolving parts B and A, insert them onto the cable carefully, not to damage
the braided wires.
4 Trim the braided wires 2
(1) Using forceps, trim the braided wires to make them straight and equally
spaced.
(2) Fold the braided wires around the part A.
Tools
cutter
measure etc.,
ADJUSTING CABLE ENDS 6-13
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(3) Cut the surplus of braided wires according to the outer of part A.
5 Trim the center conductor:

Chamfer the center conductor at a 45 angle.
Note Ensure not to damage the center conductor.
Tools
scissors
nipper
tweezers
Tools
cutter
measure
file, etc.
45
5.0 mm
6-14 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
6 Assemble connector
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until it stops. Secure the
connection to the torque value of 60 to 80 lb-in (6.8 to 9.0 Nm).
(2) Check the gap between the connector body and clamp nut:
Gap should be 0 to 0.5 mm.
Notes
1. Ensure not to put chips and shreds that are off from the braided wires
into the inner side of the central conductor and the connector body.
2. Do not rotate the cable or connector body; Rotate the clamp nut
attachment.
Tools
spanner (16 mm)
torque spanner (15 mm)
60-80 lb-in
(6.8-9.0 Nm)
0 to 0.5 mm
ADJUSTING CABLE ENDS 6-15
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Procedure 6-3 TNC-P Connector used for IDU IF IN/OUT (L-angle:TNC156(R0))
1 Inset parts, remove cable jacket:
(1) Inset the clamp nut as shown below.
(2) Remove the cable jacket for 8 mm (+1) to the end.
Note Ensure not to damage the braided wires.
Tools
knife, cutter, nipper, tweezers, file, measure,
clearance gauge, etc.
spanner, torque spanner 12 mm, 16 mm
Tools
knife
cutter
measure, etc.
Outlines of parts [Applicable cable: 5D-FB-E]
Cable jacket Aluminum tape
Braided wire
Insulator
Center conductor
Connector body
Clamp Clamp nut
Cable
Clamp nut
(8 mm +1)
*Cut the jacket edge squarely.
6-16 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
2 Inset parts:
(1) Insert the clamp as shown below.
(2) Turn the braided wires back to the clamp side.
Clamp
Braided wire
Insulator
Aluminium tape
Center conductor
Bad Example
Braids are uneven.
ADJUSTING CABLE ENDS 6-17
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Remove braided wires and insulator:
(1) Cut the insulator and an aluminium tape along the end face of braided wires
that are turned up.
Note Ensure not to damage the braided wires and the center conductor.
(2) Cut the braided wires according to a flange of clamp.
Tools
cutter
nipper
Aluminum tape
Center conductor
Braided wire
Flange
1)
2)
Aluminium tape
6-18 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Trim center conductor:
(1) Remove the center conductor as shown below.
(2) Chamfer the center conductor.
Note Ensure not to damage the center conductor (burr, etc.).
5 Assemble connector:
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until it stops.
Tools
nipper
file, etc.
Center conductor
1 mm
5 mm 1
Center conductor
Connector body
ADJUSTING CABLE ENDS 6-19
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(2) Secure the connection to the torque value of 10 Nm.
(3) Check the total length* of the connector:
* total length: 31.4 to 31.7 mm
Notes
1. Ensure not to put chips and shreds that are off from the braided wires
into the inner side of the central conductor and the connector body.
2. Do not rotate the connector body; Rotate the clamp nut attachment.
Tools
spanner (16 mm)
torque spanner (12 mm)
Clamp nut
12 mm 10 Nm
16 mm
* 31.4 to 31.7 mm
6-20 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 6-4 N-P Connector used for ODU IF IN/OUT (L-angle: 300PNR-C-NC)
1 Remove the cable jacket:
Remove the cable jacket for 6.5 mm to the end, and expose the braided wires.
Note Ensure not to damage the braided wire.
2 Trim the braided wires 1
(1) Fold the braided wires around the cable jacket.
(2) Remove the insulator for 5.0 mm to the end.
Tools
knife, cutter, nipper, tweezers, file, comb,
measure, clearance gauge, etc.
spanner, torque spanner; 16 mm,15 mm
Tools
knife
cutter
measure, etc.
Outlines of parts
Applicable cable: 5D-FB-E]
[
Cable jacket
Aluminium tape
(Connector body) (Parts A)
A
(Parts B)
B
Center conductor
Insulator
Braided wire
Clamp nut
6.5 mm
ADJUSTING CABLE ENDS 6-21
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(3) Remove the surplus of insulator/tape from the center conductor.
Note Ensure not to damage the center conductor.
3 Inset parts:
Twist the braided wires at the end and make them thinner.
As revolving parts B and A, insert them onto the cable carefully not to damage
the braided wires.
4 Trim the braided wires 2
(1) Using forceps, trim the braided wires to make them straight and equally
spaced.
Tools
cutter
measure etc.,
6-22 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
(2) Fold the braided wires around the part A.
(3) Cut the braided wire according to the outer of part A.
5 Trim the center conductor:

Chamfer the center conductor at a 45 angle.
Note Ensure not to damage the center conductor.
Tools
scissors
nipper
tweezers
Tools
cutter
measure
file, etc.
45
5.0 mm
ADJUSTING CABLE ENDS 6-23
iPASOLINK 1000: INSTALLATION NWD-118789-04E
6 Assemble connector:
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until it stops. Secure the
connection to the torque value of 60 to 80 lb-in (6.8 to 9.0 Nm).
(2) Check the gap between the connector body and clamp nut.
A gap should be 0 to 0.5 mm
Notes
1. Ensure not to put chips and shreds that are off from the braided wires
into the inner side of the central conductor and the connector body.
2. Do not rotate the connector body; Rotate the clamp nut attachment.
Tools
spanner (16 mm)
torque spanner (15 mm)
60-80 lb-in
(6.8-9.0 Nm)
0 to 0.5 mm
6-24 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 6-5 N-P Connector used for ODU IF IN/OUT (Straight: 300PNM-C-NC)
1 Remove the cable jacket:
Remove the cable jacket for 6.5 mm to the end, and expose the braided wires.
Note Ensure not to damage the braided wire.
2 Trim the braided wires 1
(1) Fold the braided wire around the cable jacket.
(2) Remove the insulator for 5.0 mm to the end.
Tools
knife, cutter, nipper, tweezers, file, comb,
measure, clearance gauge, etc.
spanner, torque spanner; 16 mm,15 mm
Tools
knife
cutter
measure, etc.
Outlines of parts
[Applicable cable: 5D-FB-E]
Cable jacket
Aluminium tape
Braided wire insulator
Center conductor
Connector body Parts A Parts B (Clamp nut)
6.5 mm
ADJUSTING CABLE ENDS 6-25
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(3) Remove the surplus of insulator/tape from the center conductor.
Note Ensure not to damage the center conductor.
3 Inset parts:
Twist the braided wires to make them thinner at the end.
As revolving parts B and A, insert them onto the cable carefully not to damage
the braided wires.
4 Trim the braided wires 2
(1) Using forceps, trim the braided wires to make them straight and equally
spaced.
Tools
cutter
measure etc.,
6-26 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
(2) Fold the braided wire around the part A.
(3) Cut the braided wires according to the outer of part A.
5 Trim the center conductor:

Chamfer the center conductor at a 45 angle.
Note Ensure not to damage the center conductor.
Tools
scissors
nipper
tweezers
Tools
cutter
measure
file, etc.
45
5.0 mm
ADJUSTING CABLE ENDS 6-27
iPASOLINK 1000: INSTALLATION NWD-118789-04E
6 Assemble connector:
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until it stops. Secure the
connection to the torque value of 60 to 80 lb-in (6.8 to 9.0 Nm).
(2) Check the gap between the connector body and clamp nut.
A gap should be 0 to 0.5 mm
Notes
1. Ensure not to put chips and shreds that are off from the braided wires
into the inner side of the central conductor and the connector body.
2. Do not rotate the connector body; Rotate the clamp nut attachment.
Tools
spanner (16 mm)
torque spanner (15 mm)
60-80 lb-in
(6.8-9.0 Nm)
0 to 0.5 mm
6-28 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 6-6 N-P Connector used for ODU IF IN/OUT (Straight: N435(R0))
1 Inset parts
Inset the clamp nut, the washer and the gasket to the cable.
2 Remove the cable jacket, inset parts:
(1) Remove the cable jacket for 13 mm to the end.
(2) Insert the clamp1 as shown below.
Note Ensure not to damage the braided wires.
Tools
knife, cutter, nipper, tweezers, file, measure,
clearance gauge, etc.
spanner, torque spanner; 16 mm
Tools
knife
cutter
measure, etc.
Outlines of parts [Applicable cable: 5D-FB-E]

Cable jacket
Aluminum tape
Braided wire Insulator
Center conductor
Washer
Clamp nut
Gasket Clamp1
Clamp2
Connector body
Cable
Clamp nut
Washer
Gasket
13 mm
(Clamp1)
ADJUSTING CABLE ENDS 6-29
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Trim the center conductor:
(1) Disentangle the braided wires end, and turn them back to the clamp 1 side. Cut
the braided wires as aligning them to the rim of clamp 1.
(2) Remove the insulator and aluminium tape as shown below without damaging
the center conductor.
(3) Remove the center conductor as shown below.
(4) Chamfer the center conductor.
Note Ensure not to damage the center conductor (burr etc.).
Tools
cutter
nipper
Tool file
Rim of clamp 1
0 to 0.5 mm
6 mm 1
1 mm
6-30 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
4 Assemble connector:
(1) The clamp 2 is inserted between the aluminium tape and the braided wire.
(2) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until stopped; the center
conductor must be inserted into the connector inner contact fingers. Tighten
the connection to the torque value of 9 to 11 Nm.
Notes
1. When inserting, do not put the chip which is braided wire inside the
central conductor and the connector body.
2. Do not turn connector body, turn clamp nut attachment.
Clamp2
Connector body
16 mm
9-11 Nm 16 mm
ADJUSTING CABLE ENDS 6-31
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(3) The gap of the connector body and clamp nut is confirmed.
(*) Gap: 2.2 to 2.7 mm
Note Do not remove the connector body tightened up once. When removing, it
is reworked from procedure 1 or a cable is exchanged.
Tools
spanner (16 mm)
torque spanner (16 mm)
clearance gauge, measure
(*): Check point
6-32 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
6.2 8D Coaxial Cable
Procedure 6-7 TNC-P Connector used for IDU IF IN/OUT
(L-angle: TNC141(R0))
In case of cable type A (|A)
1 Insertion of parts and remove of jacket of cable.
(1) The clamp nut, the washer are inserted in the cable.
(2) Remove 9 to 10 mm of jacket only.

Note Do not damage the braided wire.
Tools
knife, cutter, nipper, tweezers, file, measure,
clearance gauge, etc.
spanner, torque spanner 16 mm
Tools
knife
cutter
measure, etc.
Outlines of parts [Applicable cable: 8D-FB-E]

Cable jacket
Aluminum tape
Insulator
Braided wire
Center conductor
Connector body
Contact
cord tube
Spacer
Washer
Clamp nut
Clamp
Cable jacket
Diameter over cable jacket
|A or |B
|A: 11 mm
|B: 10 mm
Washer
Clamp nut
9-10 mm
ADJUSTING CABLE ENDS 6-33
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Insertion of parts.
(1) The clamp are inserted in the cable.
(2) The braided wire is expanded a little. The cord tube is inserted between the
aluminium tape and the braided wire.
3 Center conductor, braided wire and insulator processing.
(1) After cord tube insertion, an aluminium tape and the insulator are cut along an
end face.
(2) Turning back the braided wire in the clamp, it cuts off the part which comes
out of the flange.
(3) A central conductor is 6 to 7 mm from an end face.
Cut it to become 6 to 7 mm when there are 7 mm or more.
(4) A point of a central conductor is chamfered.
Tool tweezers
Tools
cutter
nipper
file
Clamp
Aluminium tape
Braided wire
Cord tube
Flange of clamp
Cord tube
End face
Chamfering
6 to 7 mm
6-34 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Notes
1. Do not damage the braided wire.
2. Do not damage the center conductor (brr etc.).
4 Insertion of contact.
(1) A spacer is inserted in a central conductor and contact is inserted.
Note During the contact, the spacer and the insulator there is no gap.
Refer to [common procedure] cable type A & type B for the next procedure.
In case of cable type B (|B)
1 Insertion of parts and remove of jacket of cable.
(1) The clamp nut, the washer are inserted in the cable.
(2) Remove 13 to 14 mm of jacket only.
Note Do not damage the braided wire.
Tools
knife
cutter
measure, etc.
Spacer
Contact
Gap 0
Washer
Clamp nut
13-14 mm
ADJUSTING CABLE ENDS 6-35
iPASOLINK 1000: INSTALLATION NWD-118789-04E
2 Insertion of parts.
(1) The clamp are inserted in the cable.
(2) The braided wire is expanded a little. The cord tube is inserted between the
aluminium tape and the braided wire.
Refer to the position of the cord tube by Step 3.
3 Center conductor, braided wire and insulator processing.
(1) After cord tube insertion, an aluminum tape and the insulator are cut along an
end face.
(2) Turning back the braided wire in the clamp.
(3) A central conductor is 6 to 7 mm from an end face. Cut it to become 6 to 7 mm
when there are 7 mm or more.
(4) A point of a central conductor is chamfered.
Tool tweezers
Tools
cutter
nipper
file
Clamp
Aluminum tape
Braided wire
Cord tube
(2 mm)
Flange of clamp
Cord tube
End face
Chamfering
6 to 7 mm
6-36 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Notes
1. Please note the position of the cord tube.
2. Do not damage the braided wire.
3. Do not damage the center conductor (burr etc.).
4 Insertion of contact.
(1) The clamp is moved to the cord tube side.
(2) Cut off the braided wire which comes out of the flange.
(3) A spacer is inserted in a central conductor and contact is inserted.
Note There must be no gap between the contact, the spacer and the cord
tube.
Refer to [common procedure] cable type A & type B for the next procedure.
[Common procedure] cable type A & type B
5 Connector assembly.
(1) Insert it until the cable assembly bumps inner connector.
Clamp
6 to 7 mm
Spacer
Contact
Gap 0
Connector body
ADJUSTING CABLE ENDS 6-37
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(2) The washer and clamp nut are moved to the connector side, and it tightens. The
tightening torque of the clamp nut is 8 to13 Nm.
Notes
1. When inserting, do not put the chip which is braided wire inside the
central conductor and the connector body.
2. Do not turn connector body, turn clamp nut attachment.
(3) The gap of the connector body and clamp nut is confirmed.
* Gap: 2.1 to 2.45 mm (reference)

Gap is reference, tightening must not become insufficient.
Note Do not remove the connector body tightened up once.
When removing, it is reworked from procedure 1 or a cable is
exchanged.
Tools
spanner (16 mm)
torque spanner (16 mm)
clearance gauge, measure
Washer
Clamp nut
16 mm
8 to 13 Nm 16 mm
* Check point
6-38 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 6-8 N-P Connector used for ODU IF IN/OUT
(L-angle: N-LP-8DFB(B))
1 First fit the tying metal, washer and gasket on the cable,
2 Strip back the cable sheath, taking care not to damage the braided shield, and fit
the clamp,
3 Fold back the braided shield (separating the strands of the braid) and trim it,
Note Pay attention not to damage the plait.
4 Insert the ferrule,
5 Fit the bushing,
Gasket
Washer Tying metal
Cable
[Applicable cable: 8D-FB-E]
Clamp
9 mm
Ferrule
Bush
ADJUSTING CABLE ENDS 6-39
iPASOLINK 1000: INSTALLATION NWD-118789-04E
6 Cut the aluminium foil and inner insulator away along the bushing and retain the
inner conductor,
7 Taper the edge of the center conductor using a file as shown in the enlarged view
below,
Note Pay attention not to let protrusions and indents to occur.
8 Mount the contact onto the center conductor and mount the insulator onto the
contact,
9 Insert the cable into the shell,
Insulator Contact
6-40 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
10 Tighten the tying metal by wrench using the wrench points (tighten with torque
of 4 to 10 Nm).
Wrench point
Less than 0.1 mm
(Usually no gaps)
ADJUSTING CABLE ENDS 6-41
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Procedure 6-9 N-P Connector used for ODU IF IN/OUT
(Straight: N416(R0))
1 Insertion of parts
The clamp nut, the washer and the gasket are inserted in the cable.
2 Remove of jacket of cable, insertion of parts,
(1) Remove 11 mm of jacket only.
(2) The clamp1 is inserted as shown.
Note Do not damage the braided wire.
Tools
knife, cutter, nipper, tweezers, file, measure,
clearance gauge, etc.
spanner, torque spanner; 16 mm
Tools
knife
cutter
measure, etc.
Outlines of parts [Applicable cable: 8D-FB-E]
Cable jacket Aluminium tape
Braided wire
Insulator
Center conductor
Washer
Clamp nut
Gasket Clamp1 Connector body
Cable Washer
Clamp nut Gasket
11 mm
(Clamp1)
6-42 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
3 Center conductor processing
(1) Braided wire is disentangled.
Braided wires which became straight wires are turned back to clamp1 side.
The braided wires are cut according to step of clamp1.
(2) Remove of insulator and aluminum tape as shown without damaging the center
conductor.
(3) Remove of the center conductor as shown.
(4) Chamfer the center conductor.
Note Do not damage the center conductor (burr etc.).
Tools
cutter
nipper
Tool file
Step of clamp1
1 to 2 mm
6 mm 1
1 mm
ADJUSTING CABLE ENDS 6-43
iPASOLINK 1000: INSTALLATION NWD-118789-04E
4 Connector assembly
(1) The cable center conductor must be straight and aligned with the connector
inner contact. Insert the cable into the connector body until stopped; the center
conductor must be inserted into the connector inner contact fingers. Tighten
the connection to the torque value of 9 to 11 Nm.
Notes
1. When inserting, do not put the chip which is braided wire inside the
central conductor and the connector body.
2. Do not turn connector body, turn clamp nut attachment.
(2) The gap of the connector body and clamp nut is confirmed.
(*) Gap: 0 mm
Note Do not remove the connector body tightened up once.
When removing, it is reworked from procedure 1 or a cable is
exchanged.
Tools
spanner (16 mm)
torque spanner (16 mm)
clearance gauge, measure
Connector body
16 mm
9-11 Nm 16 mm
(*): Check point
6-44 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
6.3 Other Cables
Procedure 6-10 Power Supply Cables with AMP Housing & Socket Contacts
1 Remove 3.0 to 3.5 mm of insulation.
2 Set the socket contact to the hand crimping tool.
1
2
3
4
5
6
7
8
9
10
Note: Ensure not to bend here.
Socket contact
Power connector
Power supply cable
3.0 to 3.5 mm
for 48 V, 1 A
CABLE
AWG#16-20
Hand crimping tool
91558-1
(Tyco Electronics) ( )
2
1
ADJUSTING CABLE ENDS 6-45
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Squeeze the handle of the hand crimping tool, insert cable into socket contact.
4 The cable should fit, so insulation and bare wire are arranged as shown.
5 Squeeze the handle of the hand crimping tool until the ratchet is released.
6 Twist cables for the power supply.
Note Twist power cables (+)/() to suppress inductive interference signals.
7 Insert the socket contacts into the power connector until they lock.
Insulation barrel Wire barrel
Wire strip length
()
(+)
1
2
3
4
5
6
7
8
9
10
Power connector
48 V
GND
6-46 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure 6-11 120 ohms Balanced Interface with D-Sub Connector
Notes
1. Use D-sub connectors of less than 16 mm in height as illustrated below.
2. Use D-sub 44-pin connector for the CTRL of less than 57 mm in width as
illustrated below.
1 Strip back the cable sheath, taking care not to damage the braided shield,
Note Use shielded cables which are connected to the D-Sub connector to
suppress interference from affecting the signal and to reduce
electromagnetic radiation which may interfere with other signal cables.
2 Fold back the braided shield (do not separate the strands) and trim it as shown,
Height
D-sub connector
D-sub 44-pin connector for the CTRL
Width
50 mm
Cable
Wire
ADJUSTING CABLE ENDS 6-47
iPASOLINK 1000: INSTALLATION NWD-118789-04E
3 Remove 4 mm of insulation from the end of the wire,
4 Insert the cable into the socket contact,
5 The cable should be fitted so that insulation and bare wire are arranged as shown,
6 Insert the socket contact into the hand crimping tool,
Wire
4 mm
AWG#20-24: CD-PC-111
AWG#24-28: CD-PC-121
CONFORMING WIRE SOCKET CONTRACT
Wire
Socket contact
Hand crimping tool
(HRS TC-CD-111/TC-CD-121)
CONFORMING WIRE SOCKET CONTRACT
AWG#20-24: TC-CD-111
AWG#24-28: TC-CD-121
6-48 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7 Recheck that the wire position is as shown in Step 5 before crimping the socket
contact (see illustration below),
8 Wind the metallic shield tape over the braided shield,
9 Set the cable into the plug case as shown in figure below. Then, fix the cable
using the cable clamper and two screws,
10 Referring to circle A, fix the drain wire with screw,
Wire side
Socket contact
Wire
Metallic shield tape
Cable clamper
Plug case
ADJUSTING CABLE ENDS 6-49
iPASOLINK 1000: INSTALLATION NWD-118789-04E
11 Referring to circle B, insert each wire to the specified position (Refer Interface
Terminals and Jacks for IDU in Section II OPERATING EQUIPMENT.). Insert
the socket contacts into the upper and lower row positions while taking care that
the socket contacts are inserted the right way,
Circle A
Screw
Drain wire
Circle B
6-50 ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
12 Fix the plug case with two screws, as shown in the figure.
Procedure 6-12 Auxiliary Signal Interface with D-Sub High Density Crimp Contacts
Assembly Connector
The following explains how to assemble high density crimp contacts used for
HARTING hand crimp tool as an example.
Crimping/inserting contacts process
1 Strip the jacket for 2.5 0/+0.5 mm as shown left and check if stranded wire is
not damaged,
Screw
Plug case
ADJUSTING CABLE ENDS 6-51
iPASOLINK 1000: INSTALLATION NWD-118789-04E

2 Place the handles in the open position as shown left,
Note When the handles are in close position, squeeze handles completely
until safety ratchet is released.
3 Select the suitable chamber for the selected wire,
4 Insert contact in the selected chamber,
5 Insert the prepared wire in the contact,
6 Squeeze the handles together completely until the safety ratchet clicks to open,
Jacket Stranded wire
2.5 0/+0.5 mm
Applicable wire size: 0.14 - 0.22 mm
2
(AWG26 - 24),
stranded, maximum insulation: |1.38 mm
Crimp Tool
(09 88 999 0596)
Jacket
Stamped male contacts: 09 56 000 8175 (Level S4),
High density male connectors: 09 56 300 5601 (#44)
Chamber for 0.22 mm
2
(AWG 24)
Chamber for 0.14 mm
2
(AWG 26)
Indication of the part number
6-52/END ADJUSTING CABLE ENDS
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7 Take out the crimped contacts from the chamber. Check if it should not be
scratched or transformed,
8 After crimping the stranded wire to the contact using a hand tool, insert the
contact into the contact chamber with the tool, working from the wiring side,
9 You can here the contacts snap home, audible click,
10 Check if they are securely in place with giving the wire a gentle pull.
Removing crimp contacts
1 Position the tool from the wiring side as shown left and insert into the contact
chamber. The contact can then easily be removed from the wiring side together
with itself and reinserted in a different chamber.
Note Use D-sub connectors of less than 16 mm in height as illustrated below.
Note Use D-sub 44-pin connector for the CTRL of less than 57 mm in width as
illustrated below.
Insertion and removal tool
(09 99 000 0513)
Wire
Connector
Insertion and removal tool
[Removal]
Contact can be removed
together with wire.
[Insertion]
Contact can be inserted
together with wire.
Contact chamber
Insertion and removal tool
Position the
Height
D-sub connector
D-sub 44 pin connector for the CTRL
Width
WIRING and FORMING 7-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7. WIRING and FORMING
7.1 Reference
Following shows the flow to install and route cables for the iPASOLINK 1000:
1. Connect cables for, signal interface, power supply, IF IN/OUT and ground to the
proper connector of the IDU.
(1) Connect ground cable to the ground terminal.
(2) Connect IF cable to IF IN/OUT connector.
(3) Connect power supply cable to SELV connector.
(4) Connect 16/32/48E1, STM-1, Aux. signal cables to proper connector.
(5) Connect the XIF Coaxial Cable between the paired MODEMs when
configuring the XPIC.
Note To disconnect cables, perform it in revers steps.
2. Fix the cables using cable binder to the rack as like as indicated position.
Notes
1. Do not cross the cables on front of indicators and power switch used for
maintenance.
2. Take suitable bend radius to wiring the IF cable. (5DFB: 45 mm or more,
8DFB: 70 mm or more)
3. For the IF cable connection, it is recommended to use adapter.
(Applicable adapters are listed table below.)
Table 7-1 IF Cable Adapter
IF Cable
Adapter
TNC(P) - N(J) TNC(P) - TNC(J)
5D-FB \
8D-FB \ \
7-2 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.2 Precautions
7.2.1 Connector Types
Caution
To connect an IF cable to ODU, secure
the N-Male connector with an engage
connector nut by fingers while holding
the cable by the other hand.
Tighten the engage connector nut only
for the L-angle connector also.
(Tightening Torque: 0.7 to 1.2 Nm
(7 to 12 kgcm))
ODU
ODU
IF cable
IF cable
ODU
IF cable
Straight Type
L-Angle type
L Angle type
Holding other parts on the L-angle
connector to rotate, as shown in the left,
may damage the connector.
WIRING and FORMING 7-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Caution
Tighten the TNC-male connector of IF
cable to the IDU with engage connector
nut only using fingers and holding the
cable with another hand.
Tighten the engage connector nut only for
the L-angle connector also.
(Tightening Torque: 0.3 to 0.5 Nm
(3 to 5 kgcm))
IDU
IDU
IF cable
IF cable
IDU
IF cable
Straight Type
L-Angle Type (*)
L Angle Type (*)
If rotate other parts of the
L-angle connector as illustrated left, it
can cause connector damaged.
(*) When using L-angle connector, pay
attention the following precaution to avoid
the connector damaged.
7-4 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.2.2 Connect I/F Cable with L-angle Plug to IDU
(1) Wrap the connector and cable by vinyl tape for protection.
After terminating the IF cable with a L-angle connector, it is strongly recommended
to wrap between connector and cable with vinyl tape to protect them as follows.
Connector body
starting
point
Tape width of 20 mm
is recommended.
Cable
L
L/2
slightly
20 mm
above
1) From the starting point as shown in photograph,
wrap the tape 1 to 1.5 times carefully around the joint
where the cable and connector body are connected.
Note While taping, use caution not to twist
cable against the connector.
2) Wind the tape up to slightly above a half length of
the connector. (See the photo 4 below.)
3) By pressing down the tape with fingers so it will be
firmly attached to the joint, wrap the tape up to 4 or 5
times more around the joint.
4) Use slightly above L/2 of the connector and about
the width of the tape below cable as the rough guideline
for places to cover.
WIRING and FORMING 7-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
(2) Prepare for Connecting I/F Cable to IDU.
When connecting the IF cable to the IDU, turn the IF cable itself to match face to face
their interface points between the IF cable and the IDU.
(3) Match the interfacing points between I/F Cable and IDU.
(4) Connect I/F Cable to IDU.
If it is difficult to connect by single hand, do not twist the IF cable but support softly.
Do not turn the L-
angle connector itself
to avoid high stress
to cause it damaged.
Interface point of
IDU side connector
Interface point of
Interface point of
IDU side connector
Interface point of
Cable side connector
IDU side connector
Cable side connector
7-6 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.3 Rout Cables
Following shows the method to route cables connected to iPASOLINK:
7.3.1 Grounding Cables
One Grounding Port is provided on each MODEM-A Card. Connected cables should
be routed toward the nearest side, then to the shelf top (or vice versa to connect).
7.3.2 IF Cables
One IF Port is provided on each MODEM-A Card. Connected cables should be
routed toward the nearest side, then to the shelf top (or vice versa to connect).
Grounding Port
MODEM-A Card
MODEM-A Cards and Grounding Cables on iPASOLINK 1000
WIRING and FORMING 7-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.3.3 Power Cables
One PS-M Card provides one PWR Port. PWR Cable(s) should be routed to/from the
right-side of the equipment, then to/from the shelf top.
IF Port
MODEM-A Card
MODEM-A Cards and IF Cables on iPASOLINK 1000
PS-M Cards and PWR Cables on iPASOLINK 1000
PS-M Card
PWR Port
7-8 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.3.4 16E1, STM-1, GbE and AUX Signal Cables
STM1-A Card provides two pairs (OUT/IN) of signal ports; 16E1-A Card provides
16 pairs (OUT/IN) of 2M signal ports within one terminal; GbE-A Card provides two
pairs (OUT/IN) of signal ports; AUX-A Card provides one ALM/EOW/NE2 Port.
Connected cables should be routed toward the nearest side, then to the shelf top (or
vice versa to connect).
STM1-A Card
16E1-A Card
2M IN/OUT Port
OUT IN Ports
GbE-A Card
AUX-A Card
ALM/EOW/NE2 Port
OUT IN Ports
GbE Ports
WIRING and FORMING 7-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.3.5 XIF Coaxial Cables (XPIC)
In order to configure the XPIC, XIF Coaxial Cables are required to connect the ports
on the pairing MODEM:
A pair (IN/OUT) of XIF Ports are provided on each MODEM-A Card. Surplus of the
connected cables should be routed toward the nearest side, then to the upper side to
secure them.
7.3.5.1 Connection for XPIC 1+0
XPIC 1+0 can be configured by MODEM-A Cards installed in:
Universal Slots #1 and #2
Universal Slots #3 and #4
Universal Slots #5 and #6
Universal Slots #7 and #8
Universal Slots #11 and #12
Universal Slots #13 and #14
XIF Ports
MODEM-A Card
MODEM-A Card
XIF Ports
Surplus should be routed as shown below.
Coaxial Cables
XPIC GRP n
Designated pairs for XPIC Groups
7-10 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.3.5.2 Connection for XPIC 1+1
XPIC 1+1 can be configured by MODEM-A Cards installed in:
Universal Slots #1 and #3, with #2 and #4
Universal Slots #5 and #7, with #6 and #8
Universal Slots #11 and #13, with #12 and #14
MODEM-A Cards in a Row
Coaxial Cables
XPIC GRP n
Designated pairs for XPIC Groups
Coaxial Cables
WIRING and FORMING 7-11
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.3.6 Cables Using CWDM Filter Boxes
7.3.6.1 Reference
In order to enable the CWDM, interface cables should be connected via CWDM
Filter Box.
Between the associated sites, a CWDM Filter Box A in one site, and CWDM Filter
Box B in the other site must be installed in pair for the use of designated IN and OUT
ports. See the following example:
GbE-A/STM1-A
GbE-A/STM1-A
GbE-A/STM1-A
GbE-A/STM1-A
SFP
SFP
SFP
1470 nm
1490 nm
1510 nm
CWDMF A COLORED
SFP
GbE-A/STM1-A
GbE-A/STM1-A
GbE-A/STM1-A
GbE-A/STM1-A
SFP
SFP
SFP
SFP
CWDMF B COLORED
SFP
SINGLE FIBER
iPASOLINK 1000
iPASOLINK 1000
CWDMF A: CWDM Filter Box A
CWDMF B: CWDM Filter Box B
P
A
S
S
I
V
E

C
W
D
M

F
I
L
T
E
R
P
A
S
S
I
V
E

C
W
D
M

F
I
L
T
E
R
CWDMF A
GbE-A
STM1-A
[Example]
CWDMF B
SFP
1470 nm
1490 nm
1530 nm
1550 nm
1570 nm
1590 nm
1610 nm
1510 nm
1530 nm
1550 nm
1570 nm
1590 nm
1610 nm
7-12 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.3.6.2 For CWDMF on IDU
7.3.6.3 For CWDM on Filter Box Mount
WIRING and FORMING 7-13
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.4 Connector Pin Assignments
Following show the pin assignments of connectors. Alignments in the illustrations
here are those of terminals on IDU side.
7.4.1 MC-M Card
Designation: ALM/SC/CLK
Connector Type: D-SUB (44 pins)
Table 7-2 Pin Assignment for ALM/SC/CLK Connector
D-SUB 44-pin Pin Assignment
PIN# ASSIGNMENT PIN# ASSIGNMENT PIN# ASSIGNMENT
1 ALM2 OUT (NO) 16 ALM2 OUT (COM) 31 ALM2 OUT (NC)
2 ALM1 OUT 17 ALM1 OUT (COM) 32 ALM1 OUT (NC)
3 GND 18 GND 33 V11-1 IFP (+)
4 V11-1 IDT (+) 19 V11-1 ICK (+) 34 V11-1 IFP ()
5 V11-1 IDT () 20 V11-1 ICK () 35 V11-1 OFP (+)
6 V11-1 ODT (+) 21 V11-1 OCK (+) 36 V11-1 OFP ()
7 V11-1 ODT () 22 V11-1 OCK () 37 (Reserved)
8 (Reserved) 23 (Reserved) 38 (Reserved)
9 (Reserved) 24 (Reserved) 39 (Reserved)
10 (Reserved) 25 (Reserved) 40 (Reserved)
11 (Reserved) 26 (Reserved) 41 RS-232C-1 OUT
12 RS-232C-1 IN 27 GND 42 (Reserved)
13 (Reserved) 28 GND 43 EXT1 CLK OUT (+) / OUT
14 EXT1 CLK IN (+) / IN 29 GND 44 EXT1 CLK OUT () / SG
15 EXT1 CLK IN () / SG 30 (Reserved)
ALM/SC/CLK terminal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40 41 42 43 44
7-14 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.4.2 TERM-M Card
Designation: SC
Connector Type: D-SUB15

Table 7-3 Pin Assignment for SC Connector
D-SUB 15-pin Pin Assignment
PIN# ASSIGNMENT PIN# ASSIGNMENT PIN# ASSIGNMENT
1 V11-2 IDT (+) 6 V11-2 ICK (+) 11 V11-2 IFP (+)
2 V11-2 IDT () 7 V11-2 ICK () 12 V11-2 IFP ()
3 V11-2 ODT (+) 8 V11-2 OCK (+) 13 V11-2 OFP (+)
4 V11-2 ODT () 9 V11-2 OCK () 14 V11-2 OFP ()
5 RS-232C-2 IN 10 GND 15 RS-232C-2 OUT
SC terminal
12 11
10 9
4 3 2 1 5
15 14 13
7 6 8
WIRING and FORMING 7-15
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.4.3 PS-M Card
Connector Type: Tyco D-3100S Series Connector (10-pin)

Table 7-4 Pin Assignment for Power Input Connector
Tyco D-3100S 10-pin Pin Assignment
PIN# ASSIGNMENT PIN# ASSIGNMENT
1 48 V 6 GND
2 48 V 7 GND
3 48 V 8 GND
4 48 V 9 GND
5 48 V 10 GND
Power Input terminal
1 2 3 4 5 6 7 8 9 10
7-16 WIRING and FORMING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
7.4.4 AUX-A Card
Designation: ALM/EOW/NE2
Connector Type: D-SUB 44
Table 7-5 Pin Assignment for ALM/EOW/NE2 Connector
D-SUB 44-pin Pin Assignment
PIN# ASSIGNMENT PIN# ASSIGNMENT PIN# ASSIGNMENT
1 EOW1 IN (+) 16 EOW1 IN () 31 Call 1 OUT
2 EOW1 OUT (+) 17 EOW1 OUT () 32 Bz2 IN
3 EOW2 IN (+) 18 EOW2 IN () 33 Call 2 OUT
4 EOW2 OUT (+) 19 EOW2 OUT () 34 GND
5 GND 20 ALM6/HK1/C1 OUT (COM) 35 ALM6/HK1/C1 OUT (NC)
6 ALM6/HK1/C1 OUT (NO) 21 ALM5/HK2/C2 OUT (COM) 36 ALM5/HK2/C2 OUT (NC)
7 ALM5/HK2/C2 OUT (NO) 22 ALM4/HK3/C3 OUT (COM) 37 ALM4/HK3/C3 OUT (NC)
8 ALM4/HK3/C3 OUT (NO) 23 ALM3/HK4/C4 OUT (COM) 38 ALM3/HK4/C4 OUT (NC)
9 ALM3/HK4/C4 OUT (NO) 24 NE2 RXD TERM 39 NE2 RXD (+)
10 NE2 TXD (+) 25 (Reserved) 40 NE2 RXD ()
11 NE2 TXD () 26 HK4/CLSTER3 IN () 41 HK6/CLSTER1 IN ()
12 HK2 IN () 27 HK4/CLSTER3 IN (+) 42 HK6/CLSTER1 IN (+)
13 HK2 IN (+) 28 HK3/CLSTER4 IN () 43 HK5/CLSTER2 IN ()
14 HK1 IN () 29 HK3/CLSTER4 IN (+) 44 HK5/CLSTER2 IN (+)
15 HK1 IN (+) 30 Bz1 IN
ALM/EOW/NE2 terminal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40 41 42 43 44
WIRING and FORMING 7-17
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7.4.5 16E1-A
Designation: 2M IN/OUT
Connector Type: MDR-68
Table 7-6 Pin Assignment for 2M IN/OUT Connector
MDR-68 Pin Assignment
PIN# ASSIGNMENT PIN# ASSIGNMENT
1 GND 35 GND
2 CH16_IN (+) 36 CH16_IN ()
3 CH16_OUT (+) 37 CH16_OUT ()
4 CH15_IN (+) 38 CH15_IN ()
5 CH15_OUT (+) 39 CH15_OUT ()
6 CH14_IN (+) 40 CH14_IN ()
7 CH14_OUT (+) 41 CH14_OUT ()
8 CH13_IN (+) 42 CH13_IN ()
9 CH13_OUT (+) 43 CH13_OUT ()
10 CH12_IN (+) 44 CH12_IN ()
11 CH12_OUT (+) 45 CH12_OUT ()
12 CH11_IN (+) 46 CH11_IN ()
13 CH11_OUT (+) 47 CH11_OUT ()
14 CH10_IN (+) 48 CH10_IN ()
15 CH10_OUT (+) 49 CH10_OUT ()
16 CH9_IN (+) 50 CH9_IN ()
17 CH9_OUT (+) 51 CH9_OUT ()
18 CH8_IN (+) 52 CH8_IN ()
19 CH8_OUT (+) 53 CH8_OUT ()
20 CH7_IN (+) 54 CH7_IN ()
21 CH7_OUT (+) 55 CH7_OUT ()
22 CH6_IN (+) 56 CH6_IN ()
23 CH6_OUT (+) 57 CH6_OUT ()
24 CH5_IN (+) 58 CH5_IN ()
25 CH5_OUT (+) 59 CH5_OUT ()
26 CH4_IN (+) 60 CH4_IN ()
27 CH4_OUT (+) 61 CH4_OUT ()
28 CH3_IN (+) 62 CH3_IN ()
29 CH3_OUT (+) 63 CH3_OUT ()
30 CH2_IN (+) 64 CH2_IN ()
31 CH2_OUT (+) 65 CH2_OUT ()
32 CH1_IN (+) 66 CH1_IN ()
33 CH1_OUT (+) 67 CH1_OUT ()
34 GND 68 GND
2M IN/OUT terminal
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
18/END WIRING and FORMING
iPASOLINK 1000: INSTALLATION NWD-118789-04E
This page is intentionally left blank.
GROUNDING THE FRAME 8-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
8. GROUNDING THE FRAME
When mounting IDU and ODU, ground the frame. The location of the frame ground
terminal on each IDU and ODU is shown in Figure 8-1, and the method of frame
grounding is shown in Figure 8-2.
Note Connect the Frame Ground (FG) terminal on IDU to its rack using the
earth cable. In addition, connect the rack to the indoor earth terminal
using the earth cable, and connect the FG terminal on the ODU to the
ground (refer to Figure 8-2).
Figure 8-1 Location of Frame Ground
Frame Ground Terminal on MODEM-A (when mounted)
FG
FG
IFL MON
RX LEV
6-11 GHz ODU
13-42 GHz ODU
-
I R
FG
IDU
Frame Ground Terminal
on IDU Flange
8-2 GROUNDING THE FRAME
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Cautions
1. Install the ODU within the area protected by lightning rod.
2. To avoid surge currents caused by lightning circulating in the equipment
earth system, connect the equipment earth system (frame ground) to
ground of the lightning rod at ground level.
Note Frame Ground terminal of the IDU (5 mm square cable. (means more
than 2.5 mm diameter cable (AWG #10) is recommended to apply for the
earth grounding. The proper press fix terminal tool shall be used.)
This connection is an example.
Figure 8-2 Connection for Frame Grounding (1/2)
Earth line
Indoor earth ground terminal
IDU
ODU
Coaxial cable
Protect area
Lighting rod
Outdoor earth ground terminal
(Existing or customer supplied)
Earth line
Ground
level
Rack
3 3
(Grounding Resistance:
less than 10 ohms)
This is the buried earth wire.
This type of wire is not an insulated
winding wire and recommends to
make a naked wire.
Use a copper grounding conductor to
ground the rack.
The grounding conductor to the CO
GND be connected to the rack.
GROUNDING THE FRAME 8-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Notes
* NEC recommends that frame ground of ODU should be connected to
earth line as NECs standard installation.
EP Earth Ground Point of tower
FG Frame Ground terminal of the IDU (5 mm square cable (means more
than 2.5 mm diameter cable (AWG #10) is recommended to apply for the
earth grounding. The proper press fix terminal tool shall be used.)
This connection is an example.
Fig. 8-2 Connection for Frame Grounding (2/2)
Lighting rod
Earth line
ODU
FG
Earth line*
Coaxial cable
Indoor earth line
Ground
level
IDU
(Grounding-resistance:
less than 10 ohms)
isolated from tower
(Grounding-resistance:
less than 10 ohms)
(Grounding-resistance
of tower: less than
Grounding cable for ODU should be
connected to the nearest EP of the tower.
EP
It lets through the center of the steel
tower as much as possible.
The coaxial cable lets through the inside of the steel tower.
The earth between ODU-IDU lets through the inside of the
steel tower.
Coaxial cable
Earth line
This is the buried earth
wire.
This type of wire is not an
insulated winding wire and
recommends to make a
naked wire.
10 ohms)
Use a copper grounding conductor to ground the rack.
The grounding conductor to the CO GND be connected to
the rack.
Tower
8-4/END GROUNDING THE FRAME
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.
WATERPROOFING 9-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
9. WATERPROOFING
When cable connections are completed, the following parts should be wrapped by
self-bonding tape for waterproof (see Figure 9-1).
Caution
Before connecting the I/F cable between IDU and ODU, using the circuit
tester, check that the resistance between center conductor and insulation
of the I/F cable is greater than 100 MO.
Figure 9-1 Location of Connector for Waterproof (1/2)
Pole
ANT
6/7/8 GHz band ODU
Pole
ANT
HYB/Coupler
ODU
ODU
These parts should be wrapped
the self-bonding tape tightly, twice
or more around the IF cable
connector and IF IN/OUT
connector of the ODU for
waterproof.
Note A
Note A
Note A
ODU
Self-bonding
tape
Stretch
Wrap twice the IF IN/OUT connector
with self-bonding tape for waterproofing.
A half of tape width
ODU
Twice
9-2/END WATERPROOFING
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Caution
Before connecting the I/F cable between IDU and ODU, using the circuit
tester, check that the resistance between center conductor and insulation
of the I/F cable is greater than 100 MO.
Note The self-bonding tape should be prepared by customer.
Fig. 9-1 Location of Connector for Waterproof (2/2)
ODU
IFL connector
This part should be wrapped the
self-bonding tape tightly, twice or
more around the IF cable
connector and IF IN/OUT
connector of the ODU for
waterproof.
For ODU (6-11 GHz)
For ODU (13-42 GHz)
(Bottom view)
IF cable
Self-bonding tape
ODU
Self-bonding tape
ODU
IF cable
In case of Langle
6-42 GHz BAND ODU
Self-bonding
tape
Stretch
Wrap twice the IF IN/OUT connector
with self-bonding tape for waterproofing.
A half of tape width
ODU
Twice
START-UP and SHUT-DOWN 10-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
10. START-UP and SHUT-DOWN
10.1 Start-up
Proceed with the following to start up the equipment:
Warning
1. The 48 V DC is superimposed on the centre conductor of the I/F coaxial
cable between IDU and ODU. Connecting the test device directly to this
terminal may damage the Units, and touching the coaxial cable core may
give an electrical shock.
2. Do not disconnect the I/F cable between IDU and ODU while in service. To
prevent the equipment from being damaged, turn the IDU power off before
connecting/disconnecting the I/F cable.
3. Do not allow the open/short circuit of ODU TX output while the TX is
powered on. Operate the TX ODU PWR control in the Maintenance mode or
turn the IDU PWR switch off before disconnecting the cable or feeder from
the ODU TX output.
4. After turning on the equipment, wait at least 1 minute before turning it off
again. Rapidly turning the power on and off within a short interval may
cause the equipment to fail.
Caution
1. Be careful of the top surface above MODEM of IDU and ODU that are hot
during the operation.
2. Do not apply a voltage to the equipment that varies sharply. The equipment
may operate improperly.
10-2 START-UP and SHUT-DOWN
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Procedure
Note The power to ODU is supplied from IDU.
Fig. 10-1 IDU Front View
1 Check that the I/F cable between IDU and ODU is securely connected,
2 Check that the MD/ODU PWR switches of IDU (Slot 1 and 2) are off (to the left).
3 Before connecting the power cable to IDU, check that the input voltage is 48 V
(tolerable range; within 40.5 to 57 V) using the digital multi meter,
4 Connect the power cable to IDU,
5 Confirm that the PWR indicator on IDU is on,
6 Turn the MD/ODU PWR switches of IDU on (to the right).
MD/ODU PWR switch [Slot 1]
MD/ODU PWR switch [Slot 2]
[48V, G]
Power Supply connectors
to the left
to the right
START-UP and SHUT-DOWN 10-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
10.2 Shut-down
Proceed with the following to shut down the equipment:
WarningAfter turning ON the equipment, wait at least 1
minute before turning it OFF again. Repeatedly
turning the power ON and OFF with in a short
interval may cause the IDU/ODU to fail.
Procedure
1 Turn off the MD PWR switches (Slot 1 and 2) of IDU.
2 Disconnect the power cable from IDU.
3 Confirm that all the LED indicators on IDU are off.
10.3 System #2 #4 ODU Expansion
Proceed with the following to start up the equipment when setting up #2 #4 ODU in
addition to #1 ODU that has already been in operation:
Procedure
1 Maintain that the power of IDU and that of the #1 ODU are ON.
2 Check that the MD PWR switches (Slot 2 4) of IDU are off.
3 Check that the I/F cable between IDU and ODU is securely connected,
4 Turn the MD PWR switch (Slot 2 4) of IDU on.
5 Set the #2 #4 ODU in-use by LCT.
10-4/END START-UP and SHUT-DOWN
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.
ORIENTING ANTENNA 11-1
iPASOLINK 1000: INSTALLATION NWD-118789-04E
11. ORIENTING ANTENNA
When the initial setup is completed, antenna orientations should be adjusted between
two stations according to the following steps:
Apparatus
Digital Multimeter with test leads or X0818 PASOLINK Monitor Wrench
Procedure 11-1
1 Connect the PC to the LCT port on the iPASOLINK IDU using LAN cable (see
Operation manual).
2 At each station, set the equipment into the Maintenance Mode using WebLCT.

Note While in the Maintenance mode, external Alarm outputs, except for the
Maintenance/PS (IDU) ALM, are masked, and the remote control/
operation is disabled.
3 Click and select for the following control items in Maintenance Control,
Notes
1. Retain the present status for other control items.
2. When the TX power control mode is set to ATPC, set it to MTPC and
required level for the PASOLINK link on the Equipment Setup and
Provisioning.
TX SW Manual Control: Fix Slot No.1 or Slot No.2/Slot No.3 or Slot No.4
(in 1+1 configuration)
RX SW Manual Control: Fix Slot No.1 or Slot No.2/Slot No.3 or Slot No.4
(which is the same side fixed by TX SW in
1+1 configuration.)
TX Power Control: MTPC in Equipment Setup
(at opposite site) Required level in Provisioning
4 At receiving station, remove a cap from the RX LEV MON jack,
5 At each station connect the digital multimeter or PASOLINK Monitor to the RX
LEV MON jack on the ODU,
11-2 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
6 At each station, adjust the azimuth and elevation angle of the antenna alternately
so that the measured voltage becomes maximum,
Note The relation of the RX INPUT LEVEL versus RX LEVEL MON(V) is
shown below.
RX LEVEL MON vs RX INPUT LEVEL (Typical)
RX INPUT LEVEL [dBm]
-80 -70 -60 -50 -40 -30 -20
0.5
0
1
1.5
2
2.5
3
3.5
4
4.5
R
X

L
E
V
E
L

M
O
N

[
V
]
ORIENTING ANTENNA 11-3
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Notes
1. The RX LEV MON terminal on the ODU (conformed to IEC61169-24).
2. The RX LEV MON terminal must be capped for waterproof.
Caution: Be careful, surface of the ODU is hot in operation.
Figure 11-1 Antenna Orientation Test Setup
Note The fixed bolts and nuts to be used for the antenna orientation differ with
antenna bracket types, refer to antenna bracket shown in Figure 11-4 to
Figure 11-8.

1
2 3
4
5 0
V
OW
FG
IFL MON
RX LEV
ODU (6-11 GHz)
I
ODU (13-42 GHz)
A
View A
RX LEV MON
RX LEV/OW IN
Digital multimeter
RX LEV MON
R
PASOLINK monitor
11-4 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Safety Guideline for Microwave Radiation Hazard
The Microwave and Millimeter-wave that iPASOLINK series are treating is very
small radiation level and never been reported to effect human health. But advanced
countries about health hazard have started to regulate the radiation levels. In case of
EU country, it is specified by EN50385. In order to keep the regulation, the operator
shouldn't work at near parabolic antenna during transmitter activating. Especially the
area in side to front of antenna shows higher radiation level. (Please see below figure
and calculation sample 1.)
On the other hand, in case of front side of antenna, the power density becomes high
level along antenna beam. Therefore the user of this system should pay attention not
to radiate the beam against humans any time. (Please refer below calculation sample
2.)
Figure 11-2 Hazard Area of Radiation
In addition, the power density and field strength level is calculated by equation
below.
Where:
P = Output power of ODU (dBm),
G = Antenna Gain (dBi),
(in consideration of the angle from antenna)
K = Reflection factor = 2.56 (given),
R = Distance between human and antenna (m)
ODU
Antenna
0.1 m for calculation example 1
0.1 m for calculation example 1
100 m for calculation example 2
90 to +90
degrees
Power density S mW cm
2
( )
10
P G 30 +
10
--------------------------
\ .
| |
K
40 t R
2

--------------------------------- =
ORIENTING ANTENNA 11-5
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Calculation example 1, (90 degree side of antenna)
PASOLINK = 18 GHz/+23 dBm,
Antenna diameter = 0.6 m,
0 degree antenna gain = 39 dBi,
90 degrees side antenna gain = 24 dBi, (90 degrees attenuation = 63 dB),
Distance = 0.1 m
Power density S (mW/cm
2
) = 0.0016 s 0.01 (European safety guideline)
Calculation example 2, (0 degree, front side of antenna)
PASOLINK = 7 GHz/+27 dBm,
Antenna diameter = 1.8 m,
0 degree antenna gain = 40 dBi,
Distance = 100 m
Power density S (mW/cm
2
) = 0.01 => Equal to European safety guideline
11-6 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
ANTENNA DIRECT MOUNTING TYPE
A. USING ANDREW VHLP TYPE BRACKET
Azimuth Angle Adjustment
A-1 Loosen bolts (1 in Figure 11-3).
A-2 Adjust the azimuth angle by adjusting bolt (2 in Figure 11-3).
A-3 Secure bolts loosened in Step A-1.
Elevation Angle Adjustment
A-4 Loosen bolts (3 in Figure 11-3),
A-5 Adjust the elevation angle by adjusting bolt (4 in Figure 11-3,
A-6 Secure bolts loosened in Step A-4.

Figure 11-3 Location of Adjusting Nuts and Bolts (ANDREW VHLP Type Bracket)
B. USING RFS SB1 TYPE BRACKET
Azimuth Angle Adjustment
B-1 Loosen nuts (1 in Figure 11-4),
B-2 Adjust the azimuth angle by adjusting the nuts (2 in Figure 11-4),
B-3 Secure nuts loosened in Step B-1,
2. Adjust azimuth
1. Loosen (1/2 turn) bolts
for adjusting azimuth
(top and bottom)
3. Loosen (1/2 turn) bolts
for adjusting elevation
4. Adjust elevation
ORIENTING ANTENNA 11-7
iPASOLINK 1000: INSTALLATION NWD-118789-04E
Elevation Angle Adjustment
B-4 Loosen bolt(s) (3 in Figure 11-4),
B-5 Adjust the elevation angle by adjusting the nuts (4 in Figure 11-4),
B-6 Secure nut loosened in Step B-1,
B-7 Secure nuts loosened in Step B-4.
Figure 11-4 Location of Adjusting Nuts and Bolts (RFS SB1 Type Bracket)
C. USING RFS C-Mount TYPE BRACKET
Azimuth Angle Adjustment
C-1 Loosen three bolts (1 in Figure 11-5),
C-2 Adjust azimuth angle by adjusting bolt (2 in Figure 11-5),
C-3 Secure nuts loosened in Step C-1,
Elevation Angle Adjustment
C-4 Loosen four bolts (3 in Figure 11-5),
C-5 Adjust elevation angle by adjusting bolt (4 in Figure 11-5),
C-6 Secure bolts loosened in Step C-4.
1. Loosen for adjusting azimuth
2. Adjust azimuth
3. Loosen (1/4 TURN) bolts for adjusting elevation
0.3 | m Antenna
4. Adjust elevation
11-8 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION

Figure 11-5 Location of Adjusting Nuts and Bolts (RFS C-Mount Type Bracket)
1. Loosen (1/4 turn) bolts
for adjusting azimuth
0.6 | m Antenna
3. Loosen (1/4 turn) bolts
for adjusting elevation
2. Adjust azimuth
4. Adjust elevation
ORIENTING ANTENNA 11-9
iPASOLINK 1000: INSTALLATION NWD-118789-04E
7 At each station, restore the Antenna Alignment Mode to off using the LCT,
8 At each station, reset control items to original using LCT,
9 At each station, restore the MAINT Mode to off position using the LCT,
10 At each station, disconnect the digital multimeter or PASOLINK Monitor from
the RX LEV MON connector,
11 At each station, reconnect the cap removed in Step 4,
Note The RX LEV MON connector must be capped for waterproof.
XPD Adjustment (For Antenna Direct Mounting Type)
Note The XPD adjustment using cross-polarization signal should be done
more carefully than using co-polarization signal because XPD changes
sharply in the axial direction.
1 Loosen three screws (SCREW1, 2 and 3 in Figure 11-6) and rotate antenna
(connected OMT/ODU) so that the RX LEVEL MON indicates the maximum
value at the ODU of the Main Master and Sub Master channels,
2 At opposite station, turns the ODU of the Sub Master channel power OFF (for
both No.1 and No.2 Sub Master channels in 1+1 system),
3 In this conditions, check the RX LEVEL MON indication value for XPD at the
ODU of the Sub Master channel,
4 Confirm that the XPD is more than 25 dB, if not, repeat Azimuth Angle,
Elevation Angle and XPD Adjustment,
5 At opposite station, turns the ODU of the Sub Master channel power ON,
11-10 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Figure 11-6 Location of Adjusting Nuts and Bolts (RFS C-Mount Type Bracket)
B. RFS C-Mount Type Bracket
Pole
Screw 2
Screw 3
Screw 1
Rotation
indicator
A. RFS SB1 Type Bracket
ORIENTING ANTENNA 11-11
iPASOLINK 1000: INSTALLATION NWD-118789-04E
WAVEGUIDE CONNECTION TYPE
Azimuth Angle Adjustment (Waveguide Connection Type)
Note Take care that the flexible waveguide is not forcedly twisted by rotating
the antenna.
When the HS/SD system is configured, alternately switchover the transmitter to the
other channel (No.1 or No.2) at the opposite station and repeat adjustment of
elevation and azimuth to obtain satisfactory results in both No.1 and No.2 CH.
1 Loosen all strut attachment hardware,
2 Loosen bolts indicated by arrows in Figure 11-7,
3 Loosen jam nuts and rotate turnbuckle-1 in Figure 11-7 so that the RX LEVEL
MON voltage obtains the maximum value,
4 Carefully, tighten turnbuckle-1 jam nuts and bolts indicated by arrows in Figure
11-7 to hold the adjustment.
Figure 11-7 Location of Adjusting Nuts and Bolts (Azimuth Adjustment)
Strut
Turnbuckle-1
ANDREW VHLP4 Type Bracket
11-12 ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
Elevation Angle Adjustment (Waveguide Connection Type)
1 Make sure that all strut attachment hardware is loosened,
2 Loosen bolts indicated by arrows in Figure 11-8,
3 Loosen jam nuts and rotate turnbuckle-2 in Figure 11-8 so that the RX LEVEL
MON voltage obtains the maximum value,
4 Carefully, tighten turnbuckle-2 jam nuts and bolts indicated by arrows in Figure
11-8.
Figure 11-8 Location of Adjusting Nuts and Bolts (Elevation Adjustment)
Turnbuckle-2
ANDREW VHLP4 Type Bracket
B. Elevation Adjustment
ORIENTING ANTENNA 11-13
iPASOLINK 1000: INSTALLATION NWD-118789-04E
XPD Adjustment (Waveguide Connection Type)
Note This XPD adjustment using cross-polarization signal should be done
more carefully than using co-polarization signal because XPD changes
sharply in the axial direction.
1 At opposite station, turns the ODU of the Sub Master channel power OFF (for
both No.1 and No.2 Sub Master channels in 1+1 system),
2 In this conditions, check the RX LEVEL MON indication value for XPD at the
ODU of the Sub Master channel,
3 Confirm that the XPD is more than 25 dB, if it is not obtained, repeat Azimuth
Angle, Elevation Angle for the XPD Adjustment,
4 Tighten all strut attachment hardware, turnbuckle jam nuts and bolts indicated by
arrows in Figure 11-7 and Figure 11-8,
5 At opposite station, turns the ODU of the Sub Master channel power ON (for
both No.1 and No.2 slave channels in 1+1 system),
6 At each station, disconnect the digital multimeter or OW/RX LEV Monitor from
the RX LEV MON connector,
7 At each station, reconnect the cap removed in Step 4,
Note The RX LEV MON connector must be capped for waterproof.
8 At each station, restore the Antenna Alignment Mode to off position using
the LCT,
9 At the Main Master station, when the TX power control is operated in ATPC,
restore the TX Power Control item of System Configuration changed in Step 1 to
ATPC using the LCT,
10 At the Main Master, when the TX power control is operated in MTPC, restore
MTPC TX PWR item of Provisioning Data changed in Step 2 to original
setting value using the LCT,
11 At each station, reset Maintenance to OFF.
11-14/END ORIENTING ANTENNA
NWD-118789-04E iPASOLINK 1000: INSTALLATION
This page is intentionally left blank.