TE450S Service Manual

SERVICE MANUAL
S
E
R
V
I
C
E

M
A
N
U
A
L
HYOSUNG MOTORS & MACHINERY INC.
99000HP8910
ELECTRICAL SYSTEM
COOLING SYSTEM
GROUP INDEX
GENERAL INFORMATION
1
PERIODIC MAINTENANCE
2
ENGINE
3
FUEL SYSTEM
4
5
6
CHASSIS
7
SERVICING INFORMATION
8
COPYRIGHT HYOSUNG MOTORS & MACHINERY INC. 2007.
FOREWORD
This manual contains an introductory description on
HYOSUNG and procedures for its
inspection/service and overhaul of its main compo-
nents.
Other information considered as generally known is
not included.
Read GENERAL INFORMATION section to familiar-
ize yourself with outline of the vehicle and MAINTE-
NANCE and other sections to use as a guide for
proper inspection and service.
This manual will help you know the vehicle better so
that you can assure your customers of your optimum
and quick service.
WARNING
This manual is intended for those who have
enough knowledge and skills for servicing
HYOSUNG vehicles. Without such knowledge and
skills, you should not attempt servicing by relying
on this manual only.
Instead, please contact your nearby authorized
HYOSUNG motorcycle dealer.
This manual has been prepared on the basis of
the latest specification at the time of publication.
If modification has been made since then,
difference may exist between the content of this
manual and the actual vehicle.
Illustrations in this manual are used to show the
basic principles of operation and work proce-
dures.
They may not represent the actual vehicle exact-
ly in detail.
C
O
P
Y
R
I
G
H
T
E
D
HOW TO USE THIS MANUAL
TO LOCATE WHAT YOU ARE LOOKING FOR :
1. The text of this manual is divided into sections.
2. As the title of these sections is listed on the previous page as
GROUP INDEX, select the section where you are looking for.
3. Holding the manual as shown at the right will allow you to find
the first page of the section easily.
4. On the first page of each section, its contents are listed. Find
the item and page you need.
COMPONENT PARTS
Example : Front wheel
C
O
P
Y
R
I
G
H
T
E
D
SYMBOL
Listed in the table below are the symbols indicating instructions and other information necessary for servicing and
meaning associated with them respectively.
Apply THREAD LOCK 1324.
Apply or use brake fluid.
Measure in voltage range.
Measure in resistance range.
Measure in current range.
Use special tool.
Use engine coolant.
Torque control required.
Data beside it indicates specified torque.
Apply oil.
Use engine oil unless otherwise specified.
Apply SUPER GREASE A.
Apply SILICONE GREASE.
Apply MOLY PASTE.
Apply BOND 1215.
Use fork oil.
DEFINITION SYMBOL DEFINITION SYMBOL
Apply SUPER GREASE C.
C
O
P
Y
R
I
G
H
T
E
D
NOTE
Difference between photographs and actual vehicles depends on the markets.
C
O
P
Y
R
I
G
H
T
E
D
GENERAL INFORMATION
INFORMATION LABELS 1- 1
GENERAL PRECAUTIONS 1- 2
SERIAL NUMBER LOCATION 1- 3
FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS 1- 4
BREAK-IN PROCEDURES 1- 6
EXTERIOR ILLUSTRATION 1- 7
SPECIFICATIONS 1- 8
CONTENTS
1
C
O
P
Y
R
I
G
H
T
E
D
1-1 GENERAL INFORMATION
Please note, however, that the warning and cautions contained in this manual cannot possibly cover all potential
hazards relating to the servicing, or lack of servicing, of the vehicle. In addition to the WARNING and CAUTION
stated, you must use good judgement and basic mechanical safety principles. If you are unsure about how to per-
form a particular service operation, ask a more experienced mechanic for advice.
WARNING / CAUTION / NOTE
Please read this manual and follow its instructions carefully.
To emphasize special information, the symbol and the words WARNING, CAUTION and NOTE have special meanings.
Pay special attention to the messages highlighted by these signal words.
CAUTION
Indicates a potential hazard that could result in vehicle damage.
WARNING
Indicates a potential hazard that could result in death or injury.
NOTE
Indicates special information to make maintenance easier or instructions cleaner.
C
O
P
Y
R
I
G
H
T
E
D
GENERAL INFORMATION 1-2
GENERAL PRECAUTIONS
WARNING
Proper service and repair procedures are important for the safety of the service machanic and the safety
and reliability of the vehicle.
When 2 or more persons work together, pay attention to the safety of each other.
When it is necessary to run the engine indoors, make sure that exhaust gas is forced outdoors.
When working with toxic or flammable materials, make sure that the area you work in is well-ventilated and
that you follow all off the material manufacturers instructions.
Never use gasoline as a cleaning solvent.
To avoid getting burned, do not touch the engine, engine oil, exhaust system or radiator during or for a
while after engine operation.
After servicing fuel, oil, engine coolant, exhaust or brake systems, check all lines and fittings related to the
system for leaks.
WARNING
If parts replacement is necessary, replace the parts with HYOSUNG Genuine Parts or their equivalent.
When removing parts that are to be reused, keep them arranged in an orderly manner so that they may be
reinstalled in the proper order and orientation.
Be sure to use special tools when instructed.
Make sure that all parts used in reassembly are clean, and also lubricated when specified.
When use of a certain type of lubricant, bond, or sealant is specified, be sure to use the specified type.
When removing the battery, disconnect the battery lead wire first and then the battery lead wire.
When reconnecting the battery, connect the battery lead wire first and then the battery lead wire.
Finally, cover the battery terminal with the terminal cover.
When performing service to electrical parts, if the service procedures do not require use of battery power,
diconnect the battery lead wire at the battery.
Tighten cylinder head and case bolts and nuts, beginning with larger diameter and ending with smaller
diameter, from inside to outside diagonally, to the specified tightening torque.
Whenever you remove oil seals, gaskets, packing, O-rings, locking washers, cotter pins, circlips, and cer-
tain other parts as specified, be sure to replace them with new ones. Also, before installing these new
parts, be sure to remove any material left over from the mating surfaces.
Never reuse a circlip. When installing a new circlip, take care not to expand the end gap larger than
required to slip the circlip over the shaft. After installing a circlip, always ensure that it is completely seated
in its groove and securely fitted.
Do not use self-locking nuts a few times over.
Use a torque wrench to tighten fasteners to the torque values when specified. Wipe off grease or oil if a
thread is smeared with them.
After reassembly, check parts for tightness and operation.
WARNING
To protect environment, do not unlawfully dispose of used motor oil and other fluids: batteries, and tires.
To protect Earths natural resouces, properly dispose of used vehicles and parts.
C
O
P
Y
R
I
G
H
T
E
D
SERIAL NUMBER LOCATION
The frame serial number or V.I.N. (Vehicle Identification Number) is stamped on the right side of the frame pipe.
The engine serial number is stamped on the left downside of the crankcase assembly.
These numbers are required especially for registering the machine and ordering spare parts.
FRAME SERIAL NUMBER
ENGINE SERIAL NUMBER
C
O
P
Y
R
I
G
H
T
E
D
BRAKE FLUID
Specification and classification (Front brake) : DOT4
(Rear brake) : DOT4
Classification system
API
SAE
If an SAE 10W/40 motor oil is not available, select an
alternative according to the following chart.
Use a premium quality 4-stroke motor oil to ensure
longer service life of your vehicle.
WARNING
Dont mix the unrecommended oil. It could damage the engine.
When refilling the oil tank, dont allow the dust to get inside.
Wipe the spilled oil up immediately.
Dont put the patch on the cap. It could disturb the oil to be provided and damage the engine.
WARNING
Since the brake system of this vehicle is filled with a glycol-based brake fluid by the manufacturer, do not use
or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system,
otherwise serious damage will result.
Do not use any brake fluid taken from old or used or unsealed containers.
Never re-use brake fluid left over from a previous servicing, which has been stored for a long period.
FUEL, OIL AND ENGINE COOLANT RECOMMENDATIONS
FUEL
Gasoline used should be graded 91 octane (Research Method) or higher. An unleaded gasoline type is recom-
mended.
ENGINE OIL
ENGINE OIL SPECIFICATION
Grade
Over SL
10W/40
ENGINE OIL
Temperature

-30
-22
-20
-4
-10
14
0
32
10
50
20
68
30
86
40
104
5W30
10W30
10W40 10W50
15W40 15W50
20W50
C
O
P
Y
R
I
G
H
T
E
D
ENGINE COOLANT
Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only.
WATER FOR MIXING
Use distilled water only. Water other than distilled water can corrode and clog the aluminum radiator.
ANTI-FREEZE/ENGINE COOLANT
The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze. Therefore, the engine
coolant should be used at all times even though the atmospheric temperature in your area does not go down to
freezing point.
Hyosung recommends the use of HYOSUNG COOLANT anti-freeze/engine coolant. If this is not available, use
an equivalent which is compatible with an aluminum radiator.
LIQUID AMOUNT OF WATER/ENGINE COOLANT
For engine coolant mixture information, refer to cooling system section, page 5-1.
CAUTION
Mixture of anti-freeze/engine coolant should be limited to 60%. Mixing beyond it would reduce its efficiency.
If the anti-freeze/engine coolant mixing ratio is below 50%, rust inhabiting performance is greatly reduced.
Be sure to mix it above 50% even though the atmospheric temperature does not go down to the freezing
point.
C
O
P
Y
R
I
G
H
T
E
D
After the engine has been operated for 10 hours the engine to full throttle operation, for short periods of time.
Do not maintain constant engine speed for an extended period during any portion of the break-in.
Try to vary the throttle position.
BREAK-IN PROCEDURES
During manufacture only the best possible materials are used and all machined parts are finished to a very high
standard but it is still necessary to allow the moving parts to BREAK-INbefore subjecting the engine to maximum
stresses.
The future performance and reliability of the engine depends on the care and restraint exercised during its
early life.
The general rules are as follows :
Keep to these break-in procedures :
BREAK-IN ENGINE SPEEDS
Less than 1/2 throttle Initial 10 hours
C
O
P
Y
R
I
G
H
T
E
D
1
,
1
6
5
m
m

(
H
E
I
G
H
T
)
1
,
1
6
0
m
m

(
W
I
D
T
H
)
1,810mm (LENGTH)
1,265mm (WHEEL BASE)
290mm
EXTERIOR ILLUSTRATION
C
O
P
Y
R
I
G
H
T
E
D
1,810 mm (71.3 in)
1,160 mm (45.7 in)
1,165 mm (45.9 in)
1,265 mm (49.8 in)
290 mm (11.4 in)
220 kg (485 lbs)
Overall length
Overall width
Overall height
Wheelbase
Ground clearance
Dry mass
I TEM
I TEM
I TEM
Four-stroke, DOHC, Liquid-cooled
1
96 mm (3.78 in)
62 mm (2.44 in)
448.8 (27.4 in
3
)
BDS42 TYPE
Electric starter
Wet sump
Type
Number of cylinder
Bore
Stroke
Piston displacement
Carburetor
Starter system
Lubrication system
Wet multi-plate type
5-forward and 1-reverse
1 down 4 up, foot operated
Foot / hand operated
3.143
2.538
1.684
1.261
1.040
0.885
2.231
RK 520EXW, 102 Links
SPECIFICATIONS
DIMENSIONS AND DRY MASS
ENGINE
TRANSMISSION
Clutch
Transmission
Gearshift pattern
Forward
Reverse
Final reduction
1st
2nd
Gear ratio
3rd
4th
5th
Reverse
Drive chain
C
O
P
Y
R
I
G
H
T
E
D
Independent, double wishbone, coil spring and oil damped
Swingarm type, coil spring and oil damped
37(right & left)
7.3
34 mm (1.34 in)
0 ~ 5 mm (0 ~ 0.2 in)
0
Disk brake, twin
Disk brake
21 7-10
20 11-9
Front suspension
Rear suspension
Steering angle
Caster
Trail
Toe-in [when apply to a load 75 kg (165 lbs)]
Camber
Front brake
Rear brake
Front tire size
Rear tire size
I TEM
I TEM
I TEM
Igniter type
6B.T.D.C.at 1,500 rpm
CR8E
12V 8Ah (MF)
15A
HI : 55W
LO : 55W
POSITION : 5W
LED type
10W 4
LCD type
5W
Ignition type
Ignition timing
Spark plug
Battery
Fuse
Head lamp
Brake / Tail lamp
Turn signal lamp
Speedometer lamp
License plate lamp
Fuel tank
Engine oil
Oil change
With filter change
Overhaul
Coolant
8
2,500
2,600
2,700
1.4
NOTE
The specifications are subject to change without notice.
CHASSIS
ELECTRICAL
CAPACITIES
C
O
P
Y
R
I
G
H
T
E
D
PERIODIC MAINTENANCE SCHEDULE 2- 1
PERIODIC MAINTENANCE CHART 2- 1
LUBRICATION POINTS 2- 2
MAINTENANCE PROCEDURES 2- 3
AIR CLEANER 2- 3
EXHAUST PIPE NUTS AND MUFFLER BOLTS 2- 4
VALVE CLEARANCE 2- 5
SPARK PLUG 2- 8
FUEL HOSE 2- 9
THROTTLE CABLE PLAY 2- 9
ENGINE IDLE SPEED 2- 9
ENGINE OIL AND OIL FILTER 2-10
ENGINE OIL HOSES 2-11
ENGINE COOLANT 2-12
RADIATOR HOSES 2-13
SPARK ARRESTER 2-13
CLUTCH 2-13
BRAKES 2-14
BRAKE FLUID 2-16
BRAKE HOSES 2-18
TIRES 2-18
STEERING 2-19
DRIVE CHAIN 2-20
SUSPENSIONS 2-23
CHASSIS BOLTS AND NUTS 2-23
COMPRESSION PRESSURE 2-24
OIL PRESSURE 2-25
CONTENTS
2
PERIODIC MAINTENANCE
C
O
P
Y
R
I
G
H
T
E
D
2-1 PERIODIC MAINTENANCE
Item
Initial 1 month Every 3 months Every 6 months page
Interval
Tighten
Inspect
Replace
Inspect
Inspect
Inspect
Inspect
Inspect
Inspect
Replace
Inspect
Inspect
Clean
2-3
2-4
2-5
2-8
2-9
2-10
2-11
2-9
2-9
2-13
2-12
2-13
2-13
Replace every 4 years
Replace every 18months
Item
Initial 1 month Every 3 months Every 6 months page
Interval
Drive chain
Brakes
Brake hoses
Brake fluid
Tires
Steering
Suspensions
Front and Rear wheel set nuts
Rear axle nut and lock nut
Chassis bolts and nuts
General lubrication
Inspect
Inspect
Tighten
Tighten
Lubricate
Inspect
Inspect
Inspect
Inspect
Tighten
Tighten
Lubricate
Inspect
Inspect

Tighten every time before riding
CHASSIS
2-20
2-14
2-18
2-16
2-18
2-19
2-23
7-12
7-72
2-23
2-2
PERIODIC MAINTENANCE SCHEDULE
The chart below lists the recommended intervals for all the required periodic service work necessary to keep the
vehicle operating at peak performance and economy.
Clean
Tighten
Inspect
Inspect
Inspect
Inspect
CAUTION
Using poor quality replacement parts can cause your vehicle to wear more quickly and shorten its useful life.
Use only genuine Hyoung replacement parts or their equivalent.
CAUTION
More frequent servicing should be performed on vehicles that are used under severe conditions.
PERIODIC MAINTENANCE CHART
ENGINE
Air cleaner element
Exhaust pipe nuts and muffler bolts
Valve clearance
Spark plug
Fuel hose
Engine oil and oil filter
Engine oil hoses
Throttle cable
Idle speed
Clutch
Engine coolant
Radiator hoses
Spark arrester
Inspect every time before riding
C
O
P
Y
R
I
G
H
T
E
D
PERIODIC MAINTENANCE 2-2
LUBRICATION POINTS
Proper lubrication is important for smooth operation and long life of each working part of the vehicle.
Major lubrication points are indicated below.
Clutch lever holder
Steering shaft holder
Throttle lever
Front brake lever holder
Rear brake pedal and rod link
Drive shaft joint spline
O - Motor oil, G - Grease
NOTE
Before lubricating each part, clean off any rusty spots and wipe off any grease, oil, dirt or grime.
Lubricate exposed parts which are subject to rust, with either motor oil or grease whenever the vehicle
has been operated under wet or rainy condition.
G
C
O
P
Y
R
I
G
H
T
E
D
MAI NTENANCE PROCE-
DURES
This section describes the servicing procedures for
each item mentioned in the Periodic Maintenance
chart.
AIR CLEANER
If the air cleaner is clogged with dust, intake resis-
tance will be increased, with a resultant decrease in
power output and an increase in fuel consumption.
Check and clean the air cleaner element in the fol-
lowing manner :
Remove the seat. (Refer to page 7-3)
Remove the air cleaner case cover .
Remove the air cleaner element .
Separate the polyurethane foam element , ele-
ment frame and element trap stopper .
Fill a wash pan of a proper size with a non-
flammable cleaning solvent . Immerse the air
cleaner element in the cleaning solvent and wash
it.
Press the air cleaner element between the palms
of both hands to remove the excess solvent : do
not twist or wring the element or it will tear.
Immerse the element in HYOSUNG genuine oil
, and then squeeze out the excess oil leaving
the element slightly wet.
Inspect Interval
Clean Every 3 months.
C
O
P
Y
R
I
G
H
T
E
D
Remove the drain cap of the air cleaner case to
allow any water to drain out.
Tighten the exhaust pipe nuts , muffler connect-
ing bolt , and muffler mounting bolts to the
specified torque.
EXHAUST PIPE NUTS AND MUF-
FLER BOLTS
CAUTION
Inspect the air cleaner element for tears. A torn
element must be replaced.
If driving under dusty conditions, clean the air
cleaner element more frequently. The surest
way to accelerate engine wear is to operate the
engine without the element or with torn ele-
ment. Make sure that the air cleaner element is
in good condition at all times. Life of the
engine depends largely on this component!
Inspect Interval
Tighten Initially at 1 month and Every 3 months
thereafter.
Exhaust pipe nut : 23 Nm (2.3 kgfm)
Muffler connecting bolt
: 23 Nm (2.3 kgfm)
Muffler mounting bolt
: 23 Nm (2.3 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
Remove the center front fender , center rear
fender and front fender .
Excessive valve clearance results in valve noise and
insufficient valve clearance results in valve damage
and reduced power.
Check the intake and exhaust valve clearances at
the distances indicated above and adjust the valve
clearances to specification, if necessary.
VALVE CLEARANCE
Remove the fuel tank.
Remove the spark plug.
Disconnect the oil tank overflow hose and
breather hose .
Inspect Interval
Inspect Initially at 1 month and Every 6 months
thereafter.
C
O
P
Y
R
I
G
H
T
E
D
Remove the cylinder head cover.
The valve clearance specification is different for both
intake and exhaust valves.
Valve clearance adjustment must be checked and
adjusted :
1) at the time of periodic inspection,
2) when the valve mechanism is serviced, and
3) when the camshafts are removed for servicing.
Remove the valve timing inspection plug .
Remove the magneto cover cap using the special
tool.
To inspect the valve clearance, insert a thickness
gauge between the tappet and the camshaft.
0.10 0.20 mm (0.004 ~ 0.008 in)
0.20 0.30 mm (0.008 ~ 0.012 in)
IN.
EX.
Standard (When cold) Valve clearance
NOTE
The piston must be at top dead center (TDC)
on the compression stroke in order to check or
adjust the valve clearance.
The valve clearance should only be checked
when the engine is cold.
Cap plug wrench : 09910-36000
Thickness gauge : 09900-20806
Rotate the magneto rotor counter-clockwise with a
socket wrench to set the piston at TDC on the
compression stroke.
(Rotate the rotor until the T line on the magneto
rotor is aligned with the triangle mark on the
crankcase.)
C
O
P
Y
R
I
G
H
T
E
D
Adjust valve timing, install the camshaft housing and
the tension adjuster.
After the crankshaft rotate about 10 times, measure
the valve clearance.
If the clearance be not correct, adjust the standard
clearance as the same manner above.
In case of valve adjustment which is not the tappet
shim selection chart, please follow instructions of
example in the below.
For example, the intake clearance is 0.4 and the
shim is 270 (2.70 mm), select 295 (2.95 mm) of
the shim which 270 (2.70 mm) of the shim add up
the excess clearance 0.25 mm when adjust with
the standard 0.15 as the intake standard clear-
ance 0.10.2 mm.
CAUTION
If you dont rotate the crankshaft about 10 times
before measuring the valve clearance, there is no
meaning of valve clearance.
B
D
A
C
If the clearance is out of specification, first remove
the cam chain tension adjuster, camshaft housing,
camshaft.
To install the tappet shim at original position,
record the shim NO. and clearance to present by
A, B, C, Dmark on the cylinder head.
Select the tappet that agree with tappet clearance
(vertical line) and shim NO.(horizontal line) as refer
to the tappet shim selection chart.
(Refer to page 8-3334)
C
O
P
Y
R
I
G
H
T
E
D
0.70.8 mm (0.028~0.032 in) Spark plug gap
0.7 ~0.8 mm
(0.028 ~0.032 in)
CARBON DEPOSITS
Check to see if there are carbon deposits on the
spark plug.
If carbon is deposited, remove it using a wire or pin
with a pointed end.
Disconnect the spark plug cap and remove the
spark plug.
SPARK PLUG
CR7E
CR8E
CR9E
Hot type
Standard type
Cold type
SPARK PLUG SPECIFICATION TYPE
Inspect Interval
Inspect Every 6 months.
Replace Every 18 months.
SPARK PLUG GAP
Measure the spark plug gap using a thickness
gauge.
If the spark plug gap is out of specification, adjust the
gap.
ELECTRODE
Check to see the worn or burnt condition of the elec-
trodes.
If it is extremly worn or burnt, replace the spark plug
with a new one.
And also replace the spark plug if it has a broken
insulator, damaged thread, etc.
C
O
P
Y
R
I
G
H
T
E
D
3 ~ 5 mm (0.12 ~ 0.20 in) Throttle cable play
After adjusting the throttle cable play, tighten the
lock nut .
Insert the spark plug and finger tighten it to the
cylinder head and then tighten it to the specified
torque.
FUEL HOSE
Inspect the fuel hose for damage and fuel leakage. If
any damages are found, replace the fuel hoses with
a new one.
THROTTLE CABLE PLAY
Adjust the throttle cable play as follows.
Loosen the lock nut of the throttle cable.
Turn the adjuster in or out to obtain the correct
play.
ENGINE IDLE SPEED
CAUTION
To avoid damaging the cylinder head threads ;
first, finger tighten the spark plug, and then tight-
en it to the specified torque using the spark plug
wrench.
Inspect Interval
Replace Every 4 years.
Inspect Interval
thereafter.
Inspect Interval
thereafter.
NOTE
Make this adjustment when the engine is hot.
Spark plug : 11 Nm (1.1 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
1,300 ~ 1,500 rpm Engine idle speed
Connect the engine tachometer to the high-ten-
sion cord.
Start the engine and set the engine idle speed
between 1,300 and 1,500 rpm by turning the throt-
tle stop screw .
ENGINE OIL AND OIL FILTER
ENGINE OIL REPLACEMENT
Place an oil pan under the drain plug on the
crankcase and drain plug on the oil tank. Then
drain out the engine oil by removing the engine oil
drain plug , and engine oil level gauge and
outer cover oil filler cap .
Reinstall the drain plug , and gasket. Tighten
the engine oil drain plug and to the specified
torque, and then pour the new oil through the oil
filler hole of oil tank and filler hole of outer cover.
When performing an oil change (without oil filter
replacement), the engine will hold about 2,500
Lof oil. Use an engine oil that meets the API ser-
vice classifications of over SL and that has a vis-
cosity rating of SAE 10W/40.
Install the oil lever gauge .
Install the outer cover oil filler cap .
Start the engine and allow it to run for a few min-
utes at idling speed.
Turn off the engine and wait about three minutes,
and then check the oil level on the dipstick .
(Remove the oil level gauge . Wipe the oil from
the oil level gauge using a clean rag. Reinsert the
oil level gauge until the threads touch filler neck,
but do not screw the oil level gauge in.)
If the level is below upper limit line, add oil to that
level. The vehicle must be in a level position for
accurate measurement.
The oil should be changed while the engine is warm.
Oil filter replacement at the above intervals, should
be done together with the engine oil change.
Inspect Interval
Replace Initially at 1 month and Every 6 months
thereafter.
Engine tachometer : 09900-26006
Engine oil drain plug
: 21 Nm (2.1 kgfm)
: 12 Nm (1.2 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
Inspect the engine oil hoses for damage and oil leak-
age. If any damages are found, replace the engine oil
hoses with new ones.
2,500
2,600
2,700
SAE 10W/40
API Over SL
Oil change
Oil and filter change
Engine overhaul
Engine oil type
Necessary amount of engine oil
OIL FILTER REPLACEMENT
Drain the engine oil as described in the engine oil
replacement procedure.
Replace the oil filter with a new one.
Add new engine oil and check the oil level as
described in the engine oil replacement proce-
dure.
ENGINE OIL HOSES
CAUTION
When reassembling the oil filter, make sure that
the oil filter is installed.
If the filter is installed improperly, serious engine
damage may result.
CAUTION
Necessarily, confirm and clean the oil strainer
when replace the engine oil (specially, when first
replacement).
CAUTION
More frequent servicing may be performed on
vehicle that are used under severe conditions.
Inspect Interval
thereafter.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE COOLANT
ENGINE COOLANT CHECK
Check the engine coolant level by observing the
upper and lower lines on the engine coolant
reservoir tank.
If the level is below the lower line, add engine
coolant until the level reaches the upper line.
ENGINE COOLANT REPLACEMENT
Remove the radiator cap and engine coolant
reservoir tank cap .
Place a pan below the water pump, and then drain
the engine coolant by removing the drain bolt .
Flush the radiator with fresh water, if necessary.
Tighten the drain plug securely.
Pour the specified engine coolant through the
radiator cap inlet up to the inlet neck.
Bleed air from the system as follows :
1. Shift the transmission into neutral.
Start the engine and let it idle for 2~3 minutes.
2. Snap the throttle 3~4 minutes to bleed air from
the system.
3. Stop the engine and add the engine coolant up to
the radiator cap inlet neck.
4. Repeat the above procedure until no air bleed
from the radiator cap inlet.
Inspect Interval
NOTE
For engine coolant information, refer to page 5-1.
WARNING
Do not open the radiator cap when the engine
is hot, as you may be injured by escaping hot
liquid or vapor.
Engine coolant may be harmful if swallowed or
if it comes in contact with the skin or eyes. If
engine coolant gets into the eyes or contacts
the skin, flush the eyes or wash the skin thor-
oughly, with plenty of water. If engine coolant
is swallowed, induce vomiting and call a physi-
cian immediately.
C
O
P
Y
R
I
G
H
T
E
D
5. Install the radiator cap securely.
6. After warming up and cooling down the engine
several times, add the engine coolant until the
level is between the upper and lower lines on the
engine coolant reservoir tank.
RADIATOR HOSES
Remove the spark arrester .
Clean the spark arrester pipe by brush.
Reinstall the spark arrester pipe.
A basis adjustment be allowed by the clutch lever
adjuster .
Loosen the clutch lever adjuster lock nut and
turn the clutch lever adjuster in or out to pro-
vide the specified play.
After adjustment, tighten the lock nut and cover
the rubber boot .
SPARK ARRESTER
Inspect the radiator hoses for damage and engine
coolant leakage. If any damages are found, replace
the radiator hoses with new ones.
CAUTION
Repeat the above procedure several times and
make sure the radiator is filled with the engine
coolant to the upper line of the engine coolant
reservoir tank.
Engine coolant capacity
(including reserve)
1.4
Inspect Interval
Inspect Interval
Clean Every 6 months.
CLUTCH
Inspect Interval
thereafter.
WARNING
Only clean the spark arrester in an open area
away from combustible materials. Exhausted hot
carbon particles can start a fire.
C
O
P
Y
R
I
G
H
T
E
D
BRAKE PADS
Remove the front and rear wheels.
(Refer to page 7-8)
The extent of brake pad wear can be checked by
observing the limit line on the side of brake pads.
When the wear reaches the limit line, replace the
pads with new ones. (Refer to page 7-14 and 7-42)
If not adjust by the adjuster , loosen the clutch
cable adjuster lock nut .
Turn the clutch cable adjuster in or out to pro-
vide the specified play.
After adjustment, tighten the lock nut .
The clutch cable should be lubricated with a light
weight oil whenever it is adjusted.
REAR BRAKE PEDAL
The procedure for adjusting the rear brake pedal is
as follows :
BRAKES
10 ~ 15 mm (0.4 ~ 0.6 in) Clutch cable play
Inspect Interval
thereafter.
CAUTION
Replace the brake pads as a set, otherwise brak-
ing performance will be adversely affected.
FRONT BRAKE
REAR BRAKE
C
O
P
Y
R
I
G
H
T
E
D
Remove the rear master cylinder pin.
Turn the adjuster in or out until the pedal play
to the specification, after loosening the lock nut
.
Make sure to tighten the lock nut securely.
Brake pedal play
Adjust the brake switch so the brake light comes
on when the brake pedal is depressed 7 ~ 10 mm
(0.3 ~ 0.4 in).
PARKING BRAKE
Parking brake adjustment may be required if the
parking brake does not work properly. Every time the
brake pads are replaced, adjust the parking brake.
Park the ATV on level ground.
Check the front wheels.
Lift the rear end of the ATV and place a block
under swingarm.
Loosen the parking brake adjuster lock nut .
Loosen the parking brake adjuster .
Loosen the parking brake cable adjuster lock nut
, .
Turn the adjuster , , , so that the cable
length is 54 ~ 58 mm (2.1 ~ 2.3 in).
Rear brake master cylinder rod lock nut
: 10~20 Nm (1.0~2.0 kgfm)
0 ~ 10 mm (0 ~ 0.4 in)
C
O
P
Y
R
I
G
H
T
E
D
Tighten the parking brake cable adjuster lock nut
, .
Then turn the parking brake adjuster 1/8 ~ 1/4
back.
Tighten the parking brake adjuster lock nut
while holding the parking brake adjuster in
position.
BRAKE FLUID
BRAKE FLUID LEVEL
Place the handlebar straight.
Check the brake fluid level by observing the lower
limit line on the front brake master cylinder.
When the brake fluid level is below the lower limit
line, replenish with brake fluid that meets the fol-
lowing specification.
CAUTION
After adjusting the parking brake, check that
there is no dragging when turning the rear wheel
with the wheel off the ground.
Inspect Interval
Specification and classification : DOT 4
WARNING
The brake system of this vehicle is filled with a
glycol-based brake fluid. Do not use or mix dif-
ferent types of fluid such as silicone-based and
petroleum-based fluids. Do not use any brake
fluid taken from old, used or unsealed contain-
ers. Never reuse brake fluid left over from the
last servicing or stored for a long period of
time.
Brake fluid, if it leaks, will interfere with safe
running and immediately discolor painted sur-
faces. Check the brake hoses and hose joints
for cracks and oil leakage before riding.
Parking brake adjuster lock nut
: 18 Nm (1.8 kgfm)

LOWER
LOWER
C
O
P
Y
R
I
G
H
T
E
D
AIR BLEEDING OF THE BRAKE FLUID
CIRCUIT
Air trapped in the brake fluid circuit acts like a cush-
ion to absorb a large proportion of the pressure
developed by the master cylinder and thus interferes
with the full braking performance of the brake caliper.
The presence of air is indicated by sponginessof
the brake lever/pedal and also by lack of braking
force. Considering the danger to which such trapped
air exposes the machine and rider, it is essential that,
after remounting the brake and restoring the brake
system to the normal condition, the brake fluid circuit
be purged of air in the following manner :
Fill the front or rear brake master cylinder with the
specified brake fluid to the top of the inspection
window or the upper limit line.
Replace the master cylinder cap to prevent dirt
from entering.
Attach a hose to the air bleeder valve, and insert
the free end of the hose into a receptacle.
Squeeze and release the brake lever or the brake
pedal several times in rapid succession and
squeeze the lever or push down the pedal fully
without releasing it. Loosen the air bleeder valve
by turning it a quarter of a turn so that the brake
fluid runs into the receptacle, this will remove the
tension of the brake lever causing it to touch the
handlebar grip or the brake pedal reaching bottom
of the stroke. Then, close the air bleeder valve,
pump and squeeze the brake lever or push down
the pedal and open the valve. Repeat this process
until the fluid flowing into the receptacle no longer
contains air bubbles.
Close the air bleeder valve, and disconnect the
hose. Fill the master cylinder with brake fluid to
the top of the inspection window or the upper limit
line.
NOTE
While bleeding the brake system, replenish the
brake fluid in the master cylinder as necessary.
Make sure that there is always some fluid visible
in the master cylinder.
CAUTION
Handle brake fluid with care : the fluid reacts
chemically with paint, plastics, rubber materials,
etc.
Brake caliper air bleeder valve
: 9 ~ 14 Nm (0.9 ~ 1.4 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
TIRES
TIRE TREAD CONDITION
Operating the vehicle with excessively worn tires will
decrease riding stability and consequently invite a
dangerous situation. It is highly recommended to
replace a tire when the remaining depth of the tire
tread reaches the following specification.
TIRE PRESSURE
If the tire pressure is too high or too low, steering will
be adversely affected and tire wear will increase.
Therefore, maintain the correct tire pressure for good
roadability and a longer tire life.
Cold inflation tire pressure is as follows.
VEHICLE LOAD CAPACITY LIMIT : 150 kg (330.7 lbs)
Service limit
4 mm (0.16 in)
Front and rear
tire tread depth
COLD INFLATION TIRE PRESSURE
FRONT
0.3 kgf/cm
2
30 kPa
4.4 psi
0.35 kgf/cm
2
35 kPa
4.9 psi
0.35 kgf/cm
2
35 kPa
4.9 psi
0.3 kgf/cm
2
30 kPa
4.4 psi
REAR
ONE PERSON TWO PERSONS
Inspect Interval
BRAKE HOSES
Check the brake hoses for leakage, crack, wear and
damage.
If any damages are found, replace the brake hoses
with new ones.
Inspect Interval
CAUTION
To minimize the possibility of tire damage from
over-inflation, we strongly recommended that a
manual type air pump be used rather than a high
pressure air compressor as found in service sta-
tions. When filling air into the tires, never exceed
250 kPa (2.5 kgf/cm
2
, 36 psi).
CAUTION
The standard tire fitted on this vehicle is
a 217-10 for the front and
a 2011-9 for the rear.
The use of tires other than those specified may
cause instability. It is highly recommended to use
the specified tires.
C
O
P
Y
R
I
G
H
T
E
D
Toe-in
Toe-in
Standard
0 ~ 5 mm (0 ~ 0.2 in)
[When apply to a load 75 kg (165 lbs)]
Steering system should be adjusted properly for
smooth manipulation of the handlebar and safe run-
ning.
STEERING
TOE-IN
Place the vehicle on level ground.
Make sure the tire pressure for right and left tires
is the same and set to the proper specification.
Set the front wheels in the straight position.
Place a load of 75 kg (165 lbs) on the seat.
Measure the distance and of the front
wheels with a toe-in gauge as shown and calcu-
late the difference between and .
If the toe-in is out of specification, bring it into the
specified range. (Refer to page 7-40)
Inspect Interval
thereafter.
C
O
P
Y
R
I
G
H
T
E
D
Visually check the drive chain for the possible
defects listed below.
(Support the vehicle by a jack and a wooden block,
turn the rear wheel slowly by hand with the transmis-
sion shifted to Neutral.)
Loose pins
Damaged rollers
Dry or rusted links
Kinked or binding links
Excessive wear
Improper chain adjust-
ment
Missing O-ring seals
CHECKING
Place the vehicle on a level ground.
Loosen the two rear axle housing nuts and two
rear axle housing wrench bolts .
Tense the dri ve chai n ful l y by turni ng chai n
adjuster .
DRIVE CHAIN
If any defects are found, the drive chain must be
replaced. Damage to the drive chain means that the
sprocket may also be damaged.
If any defects are found, the sprocket must be
replaced.
Inspect Interval
Inspect drive chain each time the vehicle is ridden.
NOTE
When replacing the drive chain, replace the drive
chain and sprockets as a set.
Normal wear Excessive wear
C
O
P
Y
R
I
G
H
T
E
D
Count out 21 pins (20 pitches) on the chain and
measure the distance between the two points.
If the distance exceeds the service limit, the chain
must be replaced.
ADJUSTING
Loosen or tighten chain adjuster until there is
30 ~ 40 mm (1.2 ~ 1.6 in) of slack at the middle of
the chain between the engine and rear sprockets
as shown.
After adjusting the drive chain, tighten the rear
axle housing nuts and wrench bolts in the
described order to the specified torque.
Standard
30 ~ 40 mm (1.2 ~ 1.6 in)
Drive chain slack
Service limit
319.4 mm (12.58 in)
Drive chain
20-pitch length
Rear axle housing nut
: 70 ~ 100 Nm (7.0 ~ 10.0 kgfm)
Rear axle housing wrench bolt
: 40 ~ 60 Nm (4.0 ~ 6.0 kgfm)
30 ~ 40 mm
(1.2 ~ 1.6 in)
C
O
P
Y
R
I
G
H
T
E
D
CLEANING AND LUBRICATING
Clean the drive chain with kerosine.
If the drive chain tends to rust quickly, the inter-
vals must be shortened.
After washing and drying the chain, oil it with a
engine oil or chain lubricating oil.
CAUTION
Some drive chain lubricants contain solvents and
additives which could damage the O-rings in your
chain.
Use Hyosung chain lube or an equivalent that is
specifically intended for use with O-ring chains.
CAUTION
Do not use trichloroethylene, gasoline or any sim-
ilar solvent. These fluids have too great a dissolv-
ing power for this chain and they can damage the
O-rings.
Use only kerosine to clean the drive chain.
CAUTION
The drive chain for this vehicle is made of the
special material.
The standard drive chain is a RK 520EXW recom-
mends to use this standard drive chain as a
replacement.
Use of another chain may lead to premature chain
failure.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS BOLTS AND NUTS
Check that all chassis nuts and bolts are tightened to
their specified torque. (Refer to page 8-13)
Inspect Interval
Tighten Initially at 1 month and Every 3 months
thereafter.
SUSPENSIONS
Support the vehicle with a jack or wooden blocks.
Remove the front and rear wheels.
(Refer to page 7-8)
Inspect the suspension arm, bearing and bushing
for scratches, wear, or damage.
If any damages are found, replace the suspension
arm, bearing or bushing with a new one.
(Refer to page 7-24~25)
Inspect the swingarm, rear axle and bearing for
scratches, wear or damage.
If any damages are found, replace them with a
new one. (Refer to page 7-63 and 7-69)
Inspect the front and rear shock absorbers for oil
leakage or damage.
If any damages are found, replace them with a
new one. (Refer to page 7-24 and 7-55)
Inspect Interval
C
O
P
Y
R
I
G
H
T
E
D
Low compression pressure can indicate some of the
following conditions :
Excessively worn cylinder wall
Worn-down piston or piston rings
Piston rings stuck in grooves
Poor seating of valves
Ruptured or otherwise defective cylinder head
gasket
Remove the related parts and test the compression
pressure in the following manner.
Fit the compression gauge in the plug holes.
Make sure that the connection is tightened.
Keep the throttle lever in full-open position.
Press the starter switch and crank the engine for a
few seconds.
Record the maximum gauge reading as the com-
pression of cylinder.
COMPRESSION TEST PROCEDURE
COMPRESSION PRESSURE
The compression pressure reading of a cylinder is a
good indicator of its internal condition.
The decision to overhaul the cylinder is often based
on the results of a compression test. Periodic mainte-
nance records kept at your dealership should include
compression pressure reading for each maintenance
service.
Standard
Service limit
16 kg/cm
2
(at 500 rpm)
14 kg/cm
2
(at 500 rpm)
Compression pressure
NOTE
Before testing the engine for compression
pressure, make sure that the cylinder head
nuts are tightened to the specified torque val-
ues and valves are properly adjusted.
Have the engine warmed up by idling before
testing.
Make sure that the battery is fully-charged con-
dition.
WARNING
The hot radiator and the hot engine can burn you.
Wait until the radiator and the engine are cool
enough to touch.
NOTE
When the compression pressure goes below
specification, check the engine for conditions list-
ed above.
Compression gauge : 09915-64511
C
O
P
Y
R
I
G
H
T
E
D
LOW OIL PRESSURE
Clogged oil filter
Oil leakage from the oil passage
Damaged O-ring
Defective oil pump
Combination of above items
HIGH OIL PRESSURE
Engine oil viscosity is too high
Clogged oil passage
Combination of the above items
OIL PRESSURE TEST PROCEDURE
Check the oil pressure in the following manner.
Remove the oil check plug and install the
adapter of oil pressure gauge at the removed
position.
Connect an engine tachometer.
Warm up the engine as follows :
Summer : 10 min. at 2,000 rpm.
Winter : 20 min. at 2,000 rpm.
After warming up the engine, increase the engine
speed to 3,000 rpm. (with the engine tachometer),
and read the oil pressure gauge.
OIL PRESSURE
Check the engine oil pressure periodically. This will give a good indication of the condition of the moving parts.
If the oil pressure is lower or higher than the specification, the following causes may be considered.
1.0 ~ 3.0 /
(at 60 3,000 rpm)
Oil pressure
Standard
Engine tachometer : 09900-26006
Oil pressure gauge : 09915-74511
Oil pressure gauge adaptor
: 09915-74532
Engine oil check plug
: 18 Nm (1.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
ENGINE
3
ENGINE REMOVAL AND REMOUNTING 3- 1
ENGINE REMOVAL 3- 1
ENGINE REMOUNTING 3- 6
ENGINE DISASSEMBLY 3- 9
ENGINE COMPONENT INSPECTION AND SERVICE 3-21
CYLINDER HEAD 3-21
CYLINDER 3-28
CAM CHAIN TENSION ADJUSTER AND TENSIONER 3-28
PISTON AND PISTON RING 3-29
CONROD 3-31
CRANKSHAFT 3-32
CRANK BALANCER AND BALANCER DRIVE GEAR 3-33
CLUTCH 3-35
OIL PUMP 3-36
TRANSMISSION 3-37
CRANKCASE 3-40
CLUTCH COVER 3-43
ENGINE REASSEMBLY 3-44
CONTENTS
CAUTION
Mark an identification of assembly location on each removed part so that each will be restored
to the original position during reassembly.
Wash clean and dry the removed parts before inspecting and measuring.
Oil the rotating or sliding parts before assembly.
Make sure to use the correct type of lubricant where specified.
Check that each rotating or sliding part moves or operates smoothly after assembly.
Make sure to follow the bolt tightening order where specified.
If the correct length of the bolt is confused when tightening the crankcase or cover, insert all the bolts
and check that the tightening margin is equal in each bolt.
C
O
P
Y
R
I
G
H
T
E
D
3-1 ENGINE
Disconnect the battery lead wire.
ENGI NE REMOVAL AND
REMOUNTING
ENGINE REMOVAL
Before taking the engine out of the frame, wash the
engine using a suitable cleaner.
Engine removal is sequentially explained in the fol-
lowing steps.
Drain engine coolant. (Refer to page 2-12)
Remove the engine under cover .
CAUTION
Do not lose the spacer with O-ring behind the out-
let oil hose.
Drain engine oil. (Refer to page 2-10)
Remove the gearshift lever .
Remove the engine oil outlet hose and inlet
hose .
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-2
Remove the fuel tank. (Refer to page 4-1)
Disconnect the spark plug cap , oil tank over-
flow hose and breather hose .
Remove the engine coolant inlet hose and dis-
connect the outlet hose .
Disconnect the breather hose and remove the
oil return tank with hose .
C
O
P
Y
R
I
G
H
T
E
D
3-3 ENGINE
Remove the engine sprocket cover.
Disconnect the starter motor lead wire and
ground lead wire .
Remove the carburetor with throttle cable.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-4
Remove the reverse gear cable bracket .
Disconnect the reverse gear cable .
Remove the engine sprocket with drive chain.
Remove the clutch cable bracket .
Disconnect the clutch cable end out of the
clutch lever.
Disconnect the clutch cable end out of the
clutch release arm.
Remove the clutch release arm .
Disconnect the magneto lead wire couplers and
gear position switch lead wire coupler .
C
O
P
Y
R
I
G
H
T
E
D
3-5 ENGINE
Loosen the muffler connecting bolt .
Remove the muffler mounting bolts .
Remove the exhaust pipe nuts .
Remove the muffler.
Remove the radiator .
Remove the engine mounting bolts and nut.
Remove the engine mounting brackets .
Remove the engine from the left side.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-6
Install the exhaust pipe and muffler.
ENGINE REMOUNTING
Remount the engine in the reverse order of engine removal.
Pay attention to the following points :
66 Nm (6.6 kgfm)
66 Nm (6.6 kgfm)
66 Nm (6.6 kgfm)
66 Nm (6.6 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
3-7 ENGINE
Tighten the exhaust pipe nuts , muffler mount-
ing bolts and connecting bolt to the specified
torque.
Install the engine sprocket with drive chain after
loosening the chain adjuster.
Apply THREAD LOCK 1324 to the sprocket
bolts.
Install the engine coolant hose.
Install the O-ring to the engine oil outlet hose .
Tighten the engine oil outlet hose bolt securely.
Tighten the engine oil inlet hose union bolts to the
specified torque.
Tighten the engine sprocket bolts to the specified
torque.
THREAD LOCK 1324
Exhaust pipe nut
: 23 Nm (2.3 kgfm)
: 23 Nm (2.3 kgfm)
: 23 Nm (2.3 kgfm)
Engine sprocket bolt
: 11 ~ 13 Nm (1.1 ~ 1.3 kgfm)
Engine oil inlet hose union bolt
: 23 Nm (2.3 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-8
After installing the engine, route the wiring har-
ness, cables and hoses properly.
(Refer to page 8-26 to 8-31)
Adjust the following items.
Engine oil Refer to page 2-1
Oil change
Oil and filter change
Engine overhaul
Engine oil type
2,500
2,600
2,700
SAE 10W/40
API Over SL
Adjust the drive chain slack Refer to page 2-21
Throttle cable play Refer to page 2-9
Engine idle speed Refer to page 2-9
Clutch cable play Refer to page 2-13
C
O
P
Y
R
I
G
H
T
E
D
3-9 ENGINE
ENGINE DISASSEMBLY
Remove the starter motor .
Remove the thermostat cover and 2nd pipe .
Remove the thermostat .
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-10
Remove the cam chain tension adjuster bolt .
Remove the cam chain tension adjuster .
Remove the cylinder head cover bolts in diagonal
stages, and then remove the cylinder head cover.
Remove the valve timing inspection plug .
Remove the magneto cover cap using the spe-
cial tool.
Cap plug wrench : 09910-36000
C
O
P
Y
R
I
G
H
T
E
D
3-11 ENGINE
Remove the cam chain guide and camshaft
housing .
Turn the magneto rotor until the T line on the
magneto rotor is aligned with the triangle mark on
the crankcase.
NOTE
Before removing the camshaft housing, the piston
must be at TDC of the compression stroke.
Remove the dowel pins, intake camshaft and
exhaust camshaft .
Remove the four cylinder head bolts in diagonal
stages.
NOTE
Do not drop the dowel pins and camshaft drive
chain into the crankcase.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-12
Remove the cylinder head gasket and dowel
pins .
Remove the cylinder head base bolts, and then
remove the cylinder head.
NOTE
If the cylinder head does not come off easily,
lightly tap it using a plastic hammer.
Remove the cylinder gasket and dowel pins .
Remove the cam chain guide .
Remove the cylinder base nuts , and then
remove the cylinder.
NOTE
If the cylinder does not come off easily, lightly tap
it using a plastic hammer.
C
O
P
Y
R
I
G
H
T
E
D
3-13 ENGINE
Place a clean rag over the cylinder base to pre-
vent the piston pin circlip from dropping into the
crankcase.
Remove the piston pin circlip.
Draw out the piston pin and remove the piston.
Remove the dowel pins and gasket .
Remove the magneto cover .
Remove the clutch cover .
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-14
NOTE
When remove or inspect the clutch drive and driv-
en plate, remove only the clutch pressure cover
.
Remove the dowel pins and gasket .
Remove the clutch drive plates No. 1 and driven
plates.
Remove the spring washer and spring washer
seat.
Remove the clutch drive plate No. 2.
Loosen the clutch spring mounting bolts working
in diagonal stages.
Remove the bolts and springs.
Remove the clutch pressure disk .
C
O
P
Y
R
I
G
H
T
E
D
3-15 ENGINE
Remove the clutch push piece , push rod .
Flatten the clutch sleeve hub washer .
Hold the clutch sleeve hub using the special tool,
and then remove the clutch sleeve hub nut .
Remove the clutch sleeve hub .
Remove the primary driven gear assembly and
washer.
Clutch sleeve hub holder : 09920-53710
,
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-16
Remove the coller .
Remove the oil pipe .
Remove the oil pin and oil pump assembly.
Remove the oil pump driven gear by removing
the circlip .
C
O
P
Y
R
I
G
H
T
E
D
3-17 ENGINE
Remove the gearshift shaft by removing the
circlip .
Remove the gearshift cam stopper .
Loosen the gearshift cam plate bolt .
Remove the gearshift cam plate.
With the crankshaft held immovable using the
special tool, remove the primary drive gear nut ,
washer and water pump drive gear .
CAUTION
The primary drive gear nut has left-hand threads.
If turning it counter-clockwise ( ), it may cause
damage.
Pay attention at the primary drive gear nut with a
washer, and water pump drive gear with a washer.
Conrod holder : 09910-20115
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-18
Remove the primary drive gear .
Remove the magneto rotor key .
Remove the starter driven gear .
With the magneto rotor held immovable using the
special tool, loosen the rotor nut.
Remove the magneto rotor using the special tool.
CAUTION
Do not hit the magneto rotor with a hammer, oth-
erwise the rotor may be damaged.
Rotor remover : 09930-30164
C
O
P
Y
R
I
G
H
T
E
D
3-19 ENGINE
Remove the gear position switch .
Remove the O-ri ng , swi tch contact and
spring .
Remove the cam chain and cam chain ten-
sioner .
Remove the starter idle shaft and starter idle
gear .
Remove the left crankcase securing bolts.
Remove the right crankcase securing bolts.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-20
Remove the dowel pins .
Remove the gearshift fork shafts , gearshift
forks and gearshift cam .
Separate the crankcase using the special tool.
NOTE
Fit the crankcase separator, so that the tool arms
parallel the side of the crankcase.
Remove the countershaft assembly and drive-
shaft assembly .
Remove the reverse idle gear with its shaft .
Remove the crank balancer .
Crankcase separator : 09920-13120
C
O
P
Y
R
I
G
H
T
E
D
3-21 ENGINE
Remove the crankshaft from the crankcase using
the special tool.
ENGINE COMPONENT INS-
PECTION AND SERVICE
CYLINDER HEAD
DISASSEMBLY
Remove the tappets and shims by hand or
by using a magnet.
CAUTION
Identify the position of each removed part.
Organize the parts in their respective group (for
example, exhaust or intake) so that they can be
installed in their original positions.
Compress the valve springs, and then remove the
valve cotters from the valve stem using the special
tools.
Crankcase separator : 09920-13120
Valve spring compressor : 09916-14510
Valve spring compressor attachment
: 09916-14520

C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-22
Remove the valve spring retainer , inner valve
spring and outer valve spring .
Remove the valve from the other side.
Remove the oil seal with long-nose pliers.
Remove the valve spring seat .
REASSEMBLY
Install each valve spring seat .
Apply MOLY PASTE to each oil seal and press-fit
them into position.
Apply MOLY PASTE to the valve as shown, and
then insert them into the valve guides.
Install the valve spring with the smaller pitch
facing the cylinder head.
CAUTION
Do not reuse the oil seals.
CAUTION
When inserting each valve into the valve guides,
make sure not to damage the lip of the oil seal.
MOLY PASTE
Head direction
MOLY PASTE
C
O
P
Y
R
I
G
H
T
E
D
3-23 ENGINE
Cylinder head
distortion
Cylinder head
distortion
Service limit
0.05 mm (0.002 in)
VALVE FACE WEAR
Visually inspect each valve face for wear or damage.
If any abnormal wear is found, replace the respective
valve with a new one. The thickness of the valve face
decreases as the face wears. Measure the valve
head thickness . If the valve head thickness is not
within the specified value, replace the valve with a
new one.
CYLINDER HEAD DISTORTION
Decarbonize in combustion chamber.
Check the gasket surface of the cylinder head for dis-
tortion using a straightedge and thickness gauge.
Take clearance reading at several places as indicat-
ed.
If any clearance reading exceeds the service limit,
replace the cylinder head with a new one.
Install the valve spring retainer by pressing down
the spring using the valve spring compressor. Fit
the cotter halves to the stem end and release the
lifter to allow the cotter to wedge between the
retainer and the valve stem. Make sure that the
rounded lip of the cotter fits snugly into the
groove in the stem end.
CAUTION
Be sure to install all of the parts in their original
positions.
Cylinder head
distortion
Valve head
thickness
Service limit
0.5 mm (0.02 in)

Valve spring compressor
: 09916-14510
: 09916-14520
Vernier calipers : 09900-20101

C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-24
VALVE STEM RUNOUT
Check the valve stem for abnormal wear or bend.
Support the valve using a V-blocks and measure the
valve stem runout using the dial gauge, as shown.
If the service limit is exceeded or abnormal condition
exists, replace the valve with a new one.
Cylinder head
distortion
Valve stem runout
Service limit
0.05 mm (0.002 in)
Valve clearance
0.2 ~ 0.3 mm
(0.008 ~ 0.012 in)
0.1 ~ 0.2 mm
(0.004 ~ 0.008 in)
Standard (When cold)
TAPPET & SHIM WEAR
When measuring the valve clearance, the clearance
should be within the standard range.
Exhaust valve
Intake valve
Inspect the tappet for wear and scratch.
If modification or scratch is present, replace the
tappet.
When you checked the valve clearance, if the
valve clearance is wide please replace the present
shim into thick one, if the valve clearance is nar-
row please replace the present shim into thin
shim. (Refer to page 8-3334)
SHIM KIND
There are 49 kinds of shim which thickness is increased
by each 0.025 mm from 2.30 mm to 3.50 mm.
Dial gauge : 09900-20606
Magnetic stand : 09900-20701
V-block : 09900-21304
C
O
P
Y
R
I
G
H
T
E
D
3-25 ENGINE
Valve stem deflection Service limit
0.35 mm
(0.014 in)
0.35 mm
(0.014 in)
Valve stem diameter Standard
4.975 ~ 4.990 mm (0.1959 ~ 0.1965 in)
4.955 ~ 4.970 mm (0.1951 ~ 0.1957 in)
IN.
EX.
VALVE STEM DIAMETER
Measure the valve stem outside diameter using the
micrometer.
If the diameter measured exceeds the standard,
replace the valve.
VALVE STEM DEFLECTION
Lift the valve about 10 mm (0.39 in) from the valve
seat. Measure the valve stem deflection in two direc-
tions, X and Y, perpendicular to each other.
Position the dial gauge as shown.
If the deflection exceeds the service limit, determine
whether the valve or the guide should be replaced
with a new one.
EX.
IN.
VALVE HEAD RADIAL RUNOUT
Support the valve using a v-block and measure the
valve head radial runout using the dial gauge, as
shown. If the runout exceeds the service limit,
replace the valve with a new one.
Cylinder head
distortion
Valve head radial
runout
Service limit
0.35 mm (0.014 in)
Dial gauge : 09900-20606
V-block : 09900-21304
Dial gauge : 09900-20606
Micrometer(0~25 mm) : 09900-20201
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-26
CAMSHAFT
The camshaft should be checked for runout and also
for wear of cams and journals if the engine has been
noted to produce abnormal noise or vibration or a
lack of out-put power. Any of these abnormality could
be caused by a worn camshaft.
VALVE SPRING
The force of the coil spring keeps the valve seat tight.
A weakened spring results in reduced engine power
output and often accounts for the chattering noise
coming from the valve mechanism.
Check the valve springs for proper strength by mea-
suring their free length and also by the force required
to compress them. If the spring length is less than
the service limit or if the force required to compress
the valve spring is not within specification, replace
both the inner and outer springs as a set.
Valve spring free length
Inner
Outer
Service limit
36.9 mm (1.45 in)
39.9 mm (1.57 in)
Valve spring tension
Inner
Outer
Standard
6.5 ~ 7.1 kgf
(14.3 ~ 15.7 lbs)
at length 32.0 mm (1.26 in)
12.0 ~ 14.0 kgf
(26.5 ~ 30.9 lbs)
Cam height
Intake cam
Exhaust cam
Service limit
39.88 mm (1.570 in)
39.88 mm (1.570 in)
CAMSHAFT WEAR
Worn-down cams are often the cause of mistimed
valve operation resulting in reduced output power.
The limit of cam wear is specified for both intake and
exhaust cams in terms of cam height , which is to
be measured with a micrometer. Replace camshafts
if found it worn down to the limit.

Micrometer(25~50 mm) : 09900-20202
C
O
P
Y
R
I
G
H
T
E
D
3-27 ENGINE
Camshaft housing I.D
IN.
EX.
Standard
22.012 ~ 22.025 mm
(0.8666 ~ 0.8671 in)
Camshaft O.D
IN.
EX.
Standard
21.959 ~ 21.980 mm
(0.8645 ~ 0.8654 in)
Camshaft runout
Service limit
0.10 mm (0.004 in)
Camshaft journal
oil clearance
(IN & EX)
Service limit
0.15 mm (0.006 in)
CAMSHAFT JOURNAL WEAR
Determine whether or not each journal is worn down
to the limit by measuring the oil clearance with the
camshaft installed in place.
Use the plastigauge to read the clearance at the
widest portion, which is specified as follows :
If the camshaft journal oil clearance exceeds the ser-
vi ce l i mi t, measure the i nsi de di ameter of the
camshaft housi ng and outsi de di ameter of the
camshaft journal. Replace the camshaft or the cylin-
der head and camshaft housing depending upon
which one exceeds the specification.
CAMSHAFT RUNOUT
Support the valve using a V-blocks and measure the
camshaft runout using the dial gauge. If the runout
exceeds the service limit, replace the camshaft with a
new one.
Micrometer(0 ~ 25 mm) : 09900-20201
Small bore gauge : 09900-22401
Dial gauge : 09900-20606
V-block : 09900-21304
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-28
Standard
96.000~96.015 mm
(3.7795~3.7801 in)
Service limit
96.075 mm
(3.7825 in)
Cylinder bore
Cylinder distortion
Service limit
0.05 mm (0.002 in)
CYLINDER BORE
Measure the cylinder bore diameter at six place.
If any one of the measurements exceeds the limit,
overhaul the cylinder and replace the cylinder.
CYLINDER
CYLINDER DISTORTION
Check the gasketed surface of the cylinder for distor-
tion using a straightedge and thickness gauge, taking
a clearance reading at several places as indicated.
If the largest reading at any position of the straight-
edge exceeds the limit, replace the cylinder.
CAM CHAIN TENSION ADJUS-
TER AND TENSIONER
CAM CHAIN TENSION ADJUSTER

Check that the push rod slides smoothly with the lock
shaft handle clockwise.
If it does not slide smoothly, replace the cam chain
tension adjuster with a new one.
CAM CHAIN TENSIONER

Check the contacting surface of the cam chain ten-
sioner.
If it is worn or damaged, replace it with a new one.
Cylinder gauge set : 09900-20508
C
O
P
Y
R
I
G
H
T
E
D
3-29 ENGINE
Piston diameter
Service limit
95.88 mm
(3.7748 in)
CAM CHAIN AND CAM CHAIN GUIDE
Check the cam chain for wear, damage and kinked
or binding links. If any defects are found, replace it
with a new one.
Check the cam chain guide for wear and damage. If
it is found to be damaged, replace it with a new one.
PISTON AND PISTON RING
PISTON DIAMETER INSPECTION
Measure the outside diameter of piston in the direc-
tion perpendicular to the piston pin axis at the height
from the skirt as shown in the illustration using a
micrometer.
If the measurement is found less than the service
limit, replace the piston.
PISTON-TO-CYLINDER CLEARANCE
To determine the piston-to-cylinder clearance, calcu-
late the difference between the cylinder bore and out-
side diameter of the piston.
Piston pin hole bore
Service limit
19.030 mm (0.7492 in)
PISTON PIN HOLE BORE
Using a dial calipers, measure the piston pin hole
bore both the vertical and horizontal directions.
If the measurement exceeds the service limit, replace
the piston with a new one.
18mm (0.71in)
Piston-to-cylinder
clearance
Standard Service limit
0.050~0.060 mm
(0.0020~0.0024 in)
0.120 mm
(0.0048 in)
Micrometer(75~100 mm) : 09900-20204
Dial calipers : 09900-20605
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-30
PISTON RING FREE END GAP INSPE-
CTION
Before installing piston rings, measure the free end
gap of each ring using vernier calipers. If the gap is
less than the service limit, replace the ring.
PISTON PIN DIAMETER INSPECTION
Using a micrometer, measure the piston pin outside
diameter at three position, both the ends and the
center.
If any of the measurements is founds less than the
service limit, replace the pin with a new one.
Piston pin diameter
Service limit
18.980 mm (0.7472 in)
Piston ring free end gap Standard
Approx 11 mm (0.433 in)
Approx 10 mm (0.394 in)
1st
2nd
PISTON RING END GAP INSPECTION
(Assembly condition)
Insert the piston ring squarely into the cylinder using
the piston head.
Measure the end gap with a thickness gauge.
If the gap exceeds the service limit, replace the pis-
ton ring with a new one.
Piston ring end gap
(Assembly condition)
Standard
0.25 ~ 0.40 mm
(0.010 ~ 0.016 in)
0.40 ~ 0.55 mm
(0.016 ~ 0.022 in)
2nd
1st
Piston ring end gap(Assembly condition)
1st
2nd
Service limit
0.5 mm (0.020 in)
0.7 mm (0.028 in)
Micrometer(0~25 mm) : 09900-20201
C
O
P
Y
R
I
G
H
T
E
D
3-31 ENGINE
Service limit
0.150 mm (0.006 in)
0.150 mm (0.006 in)
Piston ring-groove clearance
1st
2nd
PISTON RING-TO-GROOVE CLEAR-
ANCE INSPECTION
Remove carbon deposit both from the piston ring and
its groove.
Fit the piston ring into the groove. With the ring com-
pressed and lifted up, measure the clearance on the
bottom side of the ring using a thickness gauge.
If any clearance reading exceeds the service limt,
replace both the piston and piston rings.
Standard
1.170~1.190 mm
(0.0461~0.0469 in)
Piston ring thickness
Standard Piston ring groove width
Oil
2nd
1st
2.01~2.03 mm
(0.079~0.080 in)
1.01~1.03 mm
(0.040~0.041 in)
1.21~1.23 mm
(0.0476~0.0484 in)
2nd
1st
0.970~0.990 mm
(0.0382~0.0390 in)
CONROD
CONROD SMALL END INSIDE DIAME-
TER INSPECTION
Using a dial calipers, measure the conrod small end
inside diameter both in vertical and horizontal direc-
tions.
If any of the measurements exceeds the service limit,
replace the conrod.
Standard
19.006~19.014 mm
(0.7483~0.7486 in)
Service limit
19.040 mm
(0.7496 in)
Conrod small
end I.D.
Micrometer(0~25 mm) : 09900-20201
Dial calipers : 09900-20605
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-32
CONROD DEFLECTION INSPECTION
Wear on the big end of the conrod can be estimated
by checking the movement of the small end of the rod.
Turn the conrod and see if it moves smoothly without
play and noise. This method can also be used to
check the extent of wear on the parts of the conrods
big end.
Conrod deflection
Service limit
3.0mm (0.12 in)
CONROD BIG END SIDE CLEARANCE
INSPECTION
Push the big end of the conrod to one side and mea-
sure the side clearance using a thickness gauge.
If the clearance exceeds the service limit, replace the
crankshaft assembly with a new one or bring the
deflection and the side clearance within the service
limit by replacing the worn parts (conrod, big end
bearing, crankshaft, crank pin, etc.) with new ones.
Standard
0.10~0.65 mm
(0.004~0.026 in)
Service limit
1.0 mm
(0.040 in)
Conrod big
end side
clearance
CRANKSHAFT
CRANKSHAFT RUNOUT INSPECTION
With the right and left crank journals supported using
a V-block, turn the crankshaft slowly. At this time,
measure the crankshaft end runout using a dial
gauge. If the runout exceeds the service limit,
replace the crankshaft with a new one.
Crankshaft runout
Service limit
0.05 mm (0.002 in)
Dial gauge : 09900-20606
V-block : 09900-21304
Dial gauge : 09900-20606
V-block : 09900-21304
C
O
P
Y
R
I
G
H
T
E
D
3-33 ENGINE
CRANK BALANCER AND BALANCER DRIVE GEAR
DISASSEMBLY
Disassemble the crank balancer and balancer drive gear as shown in the illustration.
REASSEMBLY
Reassemble the crank balancer and balancer drive
gear in the reverse order of disassembly.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-34
STARTER CLUTCH
Install the starter driven gear onto the starter clutch
and turn the starter driven gear by hand(the gear
turns in only one direction). The starter driven gear
should turn smoothly. If excessive resistance is felt
while turning the starter driven gear, inspect the
starter clutch. Also, inspect the surface of the starter
driven gear which contacts the starter clutch, for
wear or damage. If any wear or damage is found,
replace the defective parts.
DISASSEMBLY
With the magneto rotor held immovable, remove
the starter clutch bolts.
REASSEMBLY
Apply a small quantity of THREAD LOCK 1324
to the starter clutch bolts and tighten them to the
specified torque with the magneto rotor held
immovable.
THREAD LOCK 1324
Starter clutch bolt
: 23~28 Nm (2.3~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
3-35 ENGINE
Service limit
0.1 mm (0.004 in)
Clutch driven plate
distortion
CLUTCH DRIVEN PLATES
Measure each clutch driven plate for distortion using
the thickness gauge. If a clutch driven plate is not
within the service limit, replace the clutch plates as a
set.
Standard
2.92~3.08 mm (0.115~0.121 in)
3.42~3.58 mm (0.135~0.141 in)
NO.1
NO.2
Clutch drive
plate
thickness
CLUTCH
CLUTCH DRIVE PLATES
Measure the thickness and claw width of the clutch
drive plates using a vernier calipers. If a clutch drive
plate is not within the service limit, replace the clutch
plates as a set.
CLUTCH SPRING FREE LENGTH
Measure the free length of each clutch spring using a
vernier calipers. If any spring is not within the service
limit, replace all of the spring with new ones.
Clutch spring
free length
Service limit
51.6 mm (2.032 in)
Service limit
2.62 mm (0.103 in)
3.12 mm (0.123 in)
NO.1
NO.2
Clutch drive
plate
thickness
Standard
15.9~16.0 mm (0.626~0.630 in)
15.9~16.0 mm (0.626~0.630 in)
NO.1
NO.2
Clutch drive
plate
claw width
Service limit
15.1 mm (0.595 in)
15.1 mm (0.595 in)
NO.1
NO.2
Clutch drive
plate
claw width
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-36
OIL PUMP
Remove the outer rotor , inner rotor and pin
.
Inspect the outer rotor and inner rotor for any
scratches or other damage.
If any damages are found, replace them with new
ones.
Apply engine oil to the sliding surfaces of the oil
pump inner rotor, outer rotor and shaft.
When installing the inner rotor , align the pin
with the groove .
When installing the outer rotor, face the punched
mark on the outer rotor to the outside.
CAUTION
The oil pump case securing screw is applied
with THREAD LOCK 1324. If an attempt is made
to overhaul the oil pump assembly, the screw
may be damaged. Only the oil pump unit is avail-
able as a replacement.
THREAD LOCK 1324
C
O
P
Y
R
I
G
H
T
E
D
3-37 ENGINE
TRANSMISSION
DISASSEMBLY
Disassemble the transmission gears as shown.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-38
INSPECTION
GEAR-SHIFTING FORK
Usi ng a thi ckness gauge, check the cl earance
between the groove of its gear and shifting fork.
The clearance for each of the three shifting forks
plays an important role in the smoothness and posi-
tiveness of shifting action.
If the clearance checked is noted to exceed the limit
specified, replace the fork or its gear, or both.
Service limit
0.50 mm
(0.020 in)
Standard
0.10~0.30 mm
(0.004~0.012 in)
Shift fork to
groove
clearance
Shift fork groove width Standard
NO.3
NO.1 & NO.2
4.85~5.00 mm
(0.191~0.197 in)
4.85~5.00 mm
(0.191~0.197 in)
Shift fork thickness Standard
NO.3
NO.1 & NO.2
5.3~5.4 mm
(0.209~0.213 in)
5.3~5.4 mm
(0.209~0.213 in)
C
O
P
Y
R
I
G
H
T
E
D
3-39 ENGINE
When installing a new circlip, pay attention to the
direction of the circlip. Fit it to the side where the
thrust is as shown in figure.
When installing the third drive gear bushing, align
the its oil hole with the driveshaft oil hole.
When installing the reverse driven gear bushing,
align the its oil hole with the driveshaft oil hole.
CAUTION
Never reuse a circlip. After a circlip has been
removed from a shaft, it should be discarded
and a new circlip must be installed.
When installing a new circlip, care must be
taken not to expand the end gap larger than
required to slip the circlip over the shaft.
After installing a circlip, always ensure that it is
completely seated in its groove and securely
fitted.
Thrust
Sharp edge
REASSEMBLY
Reassemble the transmission in the reverse order of
disassembly. Pay attention to following points :
NOTE
Before installing the gears, coat lightly engine oil
to the inner surface of each gear and bushing.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-40
TRANSMISSION GEARS AND RELATED PARTS
CRANKCASE
OIL STRAINER CAP
Remove the oil strainer cap.
C
O
P
Y
R
I
G
H
T
E
D
3-41 ENGINE
OIL PUMP DRIVE GEAR
Remove the oil pump drive gear .
BEARING INSPECTION
Wash the bearing with a cleaning solvent and lubri-
cate it with motor oil before inspection. Rotate the
inner race and check to see that it turns smoothly. If
it does not turn quietly and smoothly, or if there are
signs of any abnormalities, the bearing is defective
and must be replaced with a new one as follows.
play
play
Remove the oil strainer screw.
Clean the oil strainer using compressed air.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-42
OIL SEAL INSPECTION
Damage to the lip of the oil seal may result in leak-
age of the engine oil. Inspect the oil seal for wear or
damage. If any damages are found, replace the oil
seal with a new one.
OIL SEAL REMOVAL
Remove the oil seal retainer .
Remove the oil seal .

OIL SEAL INSTALLATION
Install the oil seals into the crankcase. Pay atten-
tion to the following points :
Apply SUPER GREASE A to the lip of the oil
seals.
Install the new oil seals.
CAUTION
Replace the removed oil seals with new ones.
SUPER GREASE A
GREASE
C
O
P
Y
R
I
G
H
T
E
D
3-43 ENGINE
CLUTCH RELEASE CAMSHAFT
Remove the clutch release camshaft .
Install the clutch release camshaft correctly.
CLUTCH COVER
OIL FILTER
Refer to page 2-11
WATER PUMP
Refer to page 5-11
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-44
ENGINE REASSEMBLY
Reassemble the engine in the reverse order of disassembly.
Pay special attention to the following points :
CRANKSHAFT
Determine the width between the webs referring to
the figure when rebuilding the crankshaft.
When mounting the crankshaft in the crankcase, it
is necessary to pull its left end into the crankcase
by using the special tools.
Width between
webs
Standard
71.00.1 mm (2.7950.004 in)
NOTE
Apply engine oil to each running and sliding part before reassembling the engine.
CAUTION
Never fit the crankshaft into the crankcase by
striking it with a plastic hammer.
Always use the special tool, otherwise the accu-
racy of the crankshaft alignment will be affected.
Crankshaft installer : 09910-32812
71.00.1
C
O
P
Y
R
I
G
H
T
E
D
3-45 ENGINE
GEARSHIFT CAM, FORK AND REVERSE LOCK SHAFT
Install the gearshift forks into the gearshifting
grooves in the correct position and direction.
Gearshift fork No. 1
Install the gearshift cam .
Install the gearshift fork shaft .
NOTE
After the gearshift fork shaft and gearshift
forks have been fitted, make sure that the
gears engage normally.
Set the transmission gears to the neutral posi-
tion.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-46
CRANKCASE
Thoroughly remove the sealant material and oil
stains on the mating surface of the right and left
crankcases.
Install the dowel pins to the crankcase.
Apply engine oil to the conrod big end and to the
transmission gears.
Apply BOND 1215 to the mating surface of the
crankcase.
Tighten the crankcase bolts to the specified
torque.
After the crankcase bolts have been tightened,
check if the crankshaft, countershaft, and drive-
shaft rotate smoothly. If a large resistance is felt to
rotation, try to free the shafts by tapping them with
a plastic hammer.
BOND 1215
Crankcase bolt : 11 Nm (1.1 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
3-47 ENGINE
STARTER CLUTCH AND MAG-
NETO ROTOR
Remove the grease from the tapered portion of
the crankshaft and the magneto rotor.
Install the starter driven gear and key .
Tighten the magneto rotor nut to the specified
torque using the special tool.
Magneto rotor nut
: 120 Nm (12.0 kgfm)
GEAR POSITION SWITCH

Install the springs , contacts and new O-ring
.
Install the gear position switch and tighten the
bolts to the specified torque.
CAM CHAIN
Install the cam chain onto the sprocket.
Tighten the cam chain tensioner mounting bolt
to the specified torque.
Install the starter idle shaft and starter idle gear
.
Gear position switch bolt
: 6.5 Nm (0.65 kgfm)
Cam chain tensioner mounting bolt
: 10 Nm (1.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-48
GEARSHIFT CAM STOPPER
Apply a small quantity THREAD LOCK 1324 to
the gearshift cam plate bolt .
Install the gearshift cam plate and gearshift cam
plate bolt .
Install the gearshift cam stopper to the speci-
fied torque.
THREAD LOCK 1324
PRIMARY DRIVE GEAR AND

WATER PUMP DRIVE GEAR
Install the primary drive gear to the crankshaft .
Install the water pump drive gear .
Apply engine oil to the thread and inside surface
of the nut.
With the crankshaft held immovable using the
special tool, and then tighten the primary drive
gear nut to the specified torque.
NOTE
This nut has left-hand thread.
CAUTION
Apply engine oil to the primary drive gear nut.
Primary drive gear nut
: 140 Nm (14.0 kgfm)
Gearshift cam stopper

: 32 Nm (3.2 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
3-49 ENGINE
When installing the oil pump driven gear, align the
pin with the groove.
Apply a small quantity of THREAD LOCK 1324
to the oil pump mounting screws, and then tighten
them securely.
OIL PIPE
Apply engine oil to the O-rings.
Tighten the oil pipe bolt securely.
THREAD LOCK 1324
Install the gearshift shaft .

Install the circlip .
OIL PUMP
Before mounting the oil pump, apply engine oil to
the sliding surfaces of the oil pump case, outer
rotor, inner rotor, and crankcase.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-50
Hold the clutch sleeve hub using the special tool,
and then tighten the clutch sleeve hub nut to the
specified torque.
Install the clutch sleeve hub , lock washer .
Clutch sleeve hub nut
: 90 Nm (9.0 kgfm)
Clutch sleeve hub holder : 09920-53710
CLUTCH
C
O
P
Y
R
I
G
H
T
E
D
3-51 ENGINE

Direction
of inside
NO. 2 Drive plate NO. 1 Drive plate
Tighten the clutch spring set bolts securely in
diagonal stages.
Bend the tongue of the washer securely.
Install the push rod , clutch push piece .
Install the clutch drive plate NO. 2 .
Install the spring washer seat and spring wash-
er onto the clutch sleeve hub correctly.
Install the clutch driven plates and drive plates
NO. 1 one by one into the clutch sleeve hub in
the prescribed order.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-52
MAGNETO ROTOR COVER
Install the dowel pins and new gasket .
Tighten the magneto rotor cover bolts securely.
CAUTION
Use a new gasket to prevent oil leakage.

CAUTION
Tighten the clutch cover bolts securely.
C
O
P
Y
R
I
G
H
T
E
D
3-53 ENGINE
PISTON RING
Install the oil ring first, the 2nd ring second, and
the 1st ring last.
NOTE
The 1st and 2nd piston rings differ in
shape.
The 1st and 2nd piston rings should be
installed with the mark facing up.
First, install a spacer into the oil ring groove,
and then install the two side rails . The spacer
and side rails do not have a designated top and
bottom. They can be installed in any position.
CAUTION
When installing the spacer, be careful not to allow
its two ends to overlap in the groove.
INCORRECT
CORRECT
Position the piston ring gaps as shown. Before
inserting the piston into its cylinder, check that the
gaps are properly positioned.
2nd ring and lower side rail
Upper side rail
1st ring and spacer
EX

IN
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-54
Place a clean rag over the cylinder base to pre-
vent the piston pin circlip from dropping into the
crankcase, and then fit the piston pin circlip with
long-nose pliers.
Apply engine oil to the sliding surface of the piston
and big end of the conrod.
Install the dowel pins and new gasket onto
the crankcase.
Hold each piston ring with the piston ring sections
positioned correctly and put it into the cylinder.
Make sure that the piston rings are caught by the
cylinder skirt.
CAUTION
Use a new piston pin circlip to prevent circlip fail-
ure with a bent one.
CAUTION
NOTE
When mounting the cylinder, after attaching the
cam chain, keep the cam chain taut. The cam
chain must not be caught between the cam chain
sprocket and crankcase when the crankshaft is
rotated.
PISTON AND CYLINDER
Apply MOLY PASTE onto the piston pin and small
end of the conrod.
NOTE
Install the piston with the punch mark on the
piston head facing toward the exhaust side.
MOLY PASTE
C
O
P
Y
R
I
G
H
T
E
D
3-55 ENGINE
Install the cam chain guide .
NOTE
Make sure that the guide is inserted properly
or binding of the cam chain and guide may result.
CAUTION
Use a new cylinder head gasket to prevent gas
leakage.
CYLINDER HEAD
With the head snugly seated on the cylinder,
secure i t by ti ghteni ng the bol ts i n di agonal
stages. Tighten the cylinder head bolts diagonally
After tightening the cylinder head bolts to specifi-
cation, tighten the cylinder head base bolts and
cylinder base nuts to the specified torque.
CAMSHAFT ASSEMBLY
Turn the magneto rotor until the T line on the
magneto rotor is aligned with the triangle mark on
the crankcase.
NOTE
Apply engine oil to the threaded parts of the
cylinder head bolts and its washers.
Be sure to install the washer with rounded side
facing up.
CAUTION
If the crankshaft is turned without drawing the
cam chain upward, the cam chain will catch
between crankcase and cam chain sprocket.
Cylinder head bolt : 47 Nm (4.7 kgfm)
Cylinder head base bolt
: 10 Nm (1.0 kgfm)
Cylinder base nut
: 10 Nm (1.0 kgfm)

C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-56
Place each camshaft into the correct position.
NOTE
Just before installing the camshaft into the cylin-
der head, apply MOLY PASTE to the camshaft
journals and cam faces. Also, apply engine oil to
the camshaft housing.
NOTE
The cam chain should now be on all three sprockets. Be careful not to move the crankshaft until the camshaft
housing and cam chain tensioner are secured.
MOLY PASTE
With the T line on the magneto rotor is aligned with the triangle mark on the crankcase, hold the camshaft
steady and lightly pull up the cam chain to remove any slack between the cam chain sprocket and exhaust
camshaft sprocket.
The exhaust camshaft sprocket has an arrow marked 1 . Turn the exhaust camshaft so that the arrow is
aligned with the gasket surface of the cylinder head. Engage the cam chain with the exhaust camshaft sprocket.
The other arrow marked 2 should now be pointing straight up. Starting from the roller pin that is directly
above the arrow marked 2 , count out 15 roller pins (from the exhaust camshaft side going towards the
intake camshaft side).
Engage the 15th roller pin on the cam chain with the arrow marked 3 on the intake sprocket. Refer to the
following illustrations.
15 Pins
1
3 C
O
P
Y
R
I
G
H
T
E
D
3-57 ENGINE
15th pin 1st pin

C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-58
Install the dowel pins .
Place each camshaft housing and cam chain
guide into the correct position.
Tighten the camshaft housing bolts to the speci-
fied torque.
CYLINDER HEAD COVER
Thoroughly wipe off oil from the fitting surfaces of
the cylinder head and cover.
Apply BOND 1215 to the end caps of the cylin-
der head cover gasket as shown.
Apply engine oil to both sides of the washer .
Lightly tighten the cylinder head cover bolts in
diagonal stages, and then tighten them to the
specified torque.
NOTE
NOTE
When tightening the camshaft housing bolts, the
piston position must be at TDC on the compres-
sion stroke.
BOND 1215
CAUTION
Use a new washers .
Camshaft housing bolt
: 10 Nm (1.0 kgfm)
Cylinder head cover bolt
: 14 Nm (1.4 kgfm)
Camshaft housing marked EX are for the
exhaust side and those marked IN are for the
intake side.
C
O
P
Y
R
I
G
H
T
E
D
3-59 ENGINE
CAM CHAIN TENSION ADJUSTER
Apply engine oil to the push rod.
Unlock the ratchet mechanism and push the push
rod all the way.
Install the new gasket and cam chain tension
adjuster to the cylinder.
Tighten the cam chain tension adjuster mounting
Tighten the cam chain tension adjuster bolt to
the specified torque.
Install the thermostat .
Cam chain tension adjuster mounting bolt
: 10 Nm (1.0 kgfm)
Cam chain tension adjuster bolt
: 20 Nm (2.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
ENGINE 3-60
Install the thermostat cover and 2nd pipe .
Install the spark plug.
Install the starter motor .
C
O
P
Y
R
I
G
H
T
E
D
CAUTION
Gasoline must be handled carefully in an area well ventilated and away from fire or sparks.
FUEL SYSTEM
FUEL TANK 4
-
1
FUEL COCK 4
-
1
FUEL PUMP 4
-
2
CARBURETOR 4
-
3
CONTENTS
4
C
O
P
Y
R
I
G
H
T
E
D
4-1 FUEL SYSTEM
FUEL TANK
REMOVAL
Remove the seat, side covers.
(Refer to page 7-3~4)
Remove the fuel tank mounting bolts .
Disconnect the fuel hose .
Drain fuel completely.
REMOUNTING
Remount the fuel tank i n the reverse order of
removal.
INSPECTION
If the fuel filter is dirty with sediment or rust, fuel will
not flow smoothly and loss of engine power may
result.
Clean the fuel filter with compressed air.
Also check the fuel cock for cracks.
FUEL COCK
REMOVAL
Drain fuel completely.
Remove the fuel cock.
WARNING
Gasoline is highly flammable and explosive. Keep
heat, sparks and flames away from gasoline.
C
O
P
Y
R
I
G
H
T
E
D
FUEL SYSTEM 4-2
REMOUNTING
Remount the fuel cock i n the reverse order of
removal.
CAUTION
Tighten the fuel cock bolts evenly.
Disconnect the fuel hose , connect the suitable
hose and insert the free end of the hose into a
receptacle.
Check the fuel flow when starting the engine for a
few seconds by pressing the starter switch.
If the fuel flow is not found, check the fuel cock.
(Refer to page 4-1)
If the fuel cock and hoses are not fault, replace the
fuel pump.
INSPECTION
REASSEMBLY
Carry out the assembly procedure in the reverse
order of disassembly.
Tighten the fuel pump mounting bolts.
Connect the fuel hoses , and vacuum hose
securely.
FUEL HOSE ROUTING :
Fuel hose (To carburetor)
Fuel hose (To fuel cock)
Vacuum hose (To intake pipe).
FUEL PUMP
REMOVAL
Remove the seat and fuel tank.
Disconnect the fuel hoses , and vacuum
hose .
Remove the fuel pump mounting bolts.
WARNING
Gasoline is very explosive. Extreme care must be
taken.
C
O
P
Y
R
I
G
H
T
E
D
4-3 FUEL SYSTEM
CARBURETOR
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
FUEL SYSTEM 4-4
REMOVAL
Remove the left side cover.
(Refer to page 7-4)
Disconnect the fuel hose .
LOCATION OF CARBURETOR
I.D.NO.
The carburetor I.D. is stamped on the location on the
carburetor as shown in the right photo.
Loosen the carburetor clamp screw.
Remove the carburetor side cap .
C
O
P
Y
R
I
G
H
T
E
D
4-5 FUEL SYSTEM
Disconnect the throttle cable .
Remove the O-ring .
DISASSEMBLY
Remove the fuel hose and air vent hoses .
Remove the throttle stop screw .
Remove the choke lever .
Remove the carburetor top cap .
CAUTION
Do not use compressed air on the carburetor
body removing the diaphragm : this may damage
the diaphragm.
C
O
P
Y
R
I
G
H
T
E
D
FUEL SYSTEM 4-6
Remove the spring , along with the diaphragm
assembly .
Remove the jet needle holder , spring , E-ring
, ring and jet needle .
Remove the diaphragm cover .
Remove the diaphragm .
C
O
P
Y
R
I
G
H
T
E
D
4-7 FUEL SYSTEM
Remove the O-ring .
Remove the float chamber body .
Remove the float pin , float and needle valve
.
Remove the valve seat .
CAUTION
Replace the removed O-ring with a new one to
prevent leakage of fuel.
C
O
P
Y
R
I
G
H
T
E
D
FUEL SYSTEM 4-8
Remove the main jet , jet holder and pilot jet
.
Remove the pilot air jet counting and tightening
the number of turn.
INSPECTION
Check the following parts for damage and clogging.
Pilot jet Piston valve
Main jet Starter jet
Main air jet Gaskets and O-rings
Pilot air jet Pilot outlet and bypass
Needle jet holder Float
Needle valve Jet needle
Valve seat Diaphragm
If any abnormal condition is found, wash the part clean.
If damage or clogging is found, replace the part with
a new one.
CLEANING
Clean all jets by using compressed air.
After cleaning, reassemble the carburetor with
new seals and gaskets.
Needle valve
Check for
stopped
wear
Foreign
substance
NOTE
Before removing the pilot air jet , its setting
must be determined. Slowly turn the pilot screw
clockwise and count the number of turns until it
is lightly seated. Make a note of how many turns
were made. When reassembling the pilot screw,
you will want to set it to its original position.
CAUTION
Do not use wire to clean the passageways, valve
seat and jets. Used compressed air only.
,
C
O
P
Y
R
I
G
H
T
E
D
4-9 FUEL SYSTEM
FLOAT HEIGHT ADJUSTMENT
To check the float height, turn the carburetor upside
down. Measure the float height while the float arm
is just contacting the needle valve using a vernier
calipers.
Float height 13 mm (0.51 in)
Bend the float arm as necessary to bring the
height to the specified level.
After adjustment, check the float height and the
fuel level again.
REASSEMBLY
Carburetor reassembly can be performed in the
reverse order of disassembly. When reassembling,
carefully observe the following instructions.
After cleaning, reinstall the pilot air jet to the origi-
nal setting by turning the screw in until it lightly
seat, and then backing it out the same number of
turns counted during disassembly.
Install the pilot jet , jet holder and main jet .
C
O
P
Y
R
I
G
H
T
E
D
FUEL SYSTEM 4-10
Align the hole of the diaphragm with passage-
way on the carburetor body.
REMOUNTING
Remount the carburetor assembly in the reverse
order of removal.
Align the lug on the carburetor with intake pipes
cutout.
Connect the carburetor hoses properly.
After the carburetor assembly has been remount-
ed onto the engine, perform the following adjust-
ment.
Throttle cable adjustment. Refer to page 2-9
Idle speed adjustment. Refer to page 2-9
Apply SUPER GREASE A to thread part of the
throttle stop screw, then install the throttle stop
screw to the carburetor.
SUPER GREASE A
NOTE
When installing the diaphram, make sure the
diaphram is seated at the concave section of the
carburetor.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE COOLANT 5
-
1
COOLING CIRCUIT 5
-
2
RADIATOR 5
-
2
COOLING FAN 5- 5
COOLING FAN THERMO-SWITCH 5- 6
WATER TEMPERATURE SWITCH 5
-
8
THERMOSTAT 5
-
9
WATER PUMP 5
-
11
OIL TANK AND HOSES 5
-16
COOLING SYSTEM
5
CONTENTS
C
O
P
Y
R
I
G
H
T
E
D
5-1 COOLING SYSTEM
ENGINE COOLANT
At the time of manufacture, the cooling system is
filled with a 50 : 50 mixture of distilled water and
ethylene glycol anti-freeze.
This 50 : 50 mixture will provide the optimum corro-
sion protection and excellent heat protection, and will
protect the cooling system from freezing at tempera-
tures above -31
(-24
).
If the vehicle is to be exposed to temperatures below
-31
(-24
), this mixing ratio should be increased

up to 55% or 60% according to the figure.
CAUTION
Use a high quality ethylene glycol base anti-
freeze, mixed with distilled water. Do not mix
an alcohol base anti-freeze and different
brands of anti-freeze.
Do not put in more than 60% anti-freeze or less
than 50%. (Refer to Right figure.)
Do not use a radiator anti-leak additive.
50% Engine coolant including reserve tank capacity
Anti-freeze
Water
0.7
0.7
WARNING
You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot. After the
engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to
allow pressure to escape and then turn the cap all the way off.
The engine must be cool before servicing the cooling system.
Coolant is harmful ;
If it comes in contact with skin or eyes, flush with water.
If swallowed accidentally, induce vomiting and call physician immediately.
Keep it away from children.
F
r
e
e
z
i
n
g

p
o
i
n
t
B
o
i
l
i
n
g

p
o
i
n
t
G
a
u
g
e

p
r
e
s
s
u
r
e
Density (%)
Fig.1 Engine coolant density-freez-
ing point curve.
Density (%)
Fig.2 Engine coolant density-boiling
point curve.
(kgf/)
Anti-freeze density Freezing point
50%
55%
60%
-31
(-24
)
-40
(-40
)
-55
(-67
)
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-2
COOLING CIRCUIT
RADIATOR
REMOVAL
Remove the front fender. (Refer to page 7-3)
Drain engine coolant by removing the drain bolt
.
Disconnect the cooling fan thermo-switch lead
wire coupler and water temperature switch lead
wire coupler .
Disconnect the radiator inlet hose and outlet hose
.
Impeller
Radiator cap
Radiator
Thermostat
Cooling fan thermo-switch
Water temperature switch
C
O
P
Y
R
I
G
H
T
E
D
5-3 COOLING SYSTEM
INSPECTION AND CLEANING
Road dirt or trash stuck to the fins must be removed.
Use of compressed air is recommended for this
cleaning.
Remove the radiator by the mounting bolts.
Disconnect reserve tank hose .
Disconnect the cooling fan motor lead wire cou-
pler.
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-4
REMOUNTING
The radiator reassembly can be performed in the
reverse order of disassembly procedures.
However, the following points must be observed in
the reassembly operation.
Install the radiator with the specified torque.
RADIATOR RESERVOIR TANK
REMOVAL / REMOUNTING
Remove the reservoir tank mounting bolts and dis-
connect the siphon hose from the reservoir tank
and drain engine coolant.
Install the reservoir tank in the reverse order of
removal.
Fill the reservoir tank to the upper level line.
Pour engine coolant Refer to page 2-12
Bleed air from the cooling circuitRefer to page 2-12
Fi ns bent down or dented can be repai red by
straightening them with the blade of a small screw-
driver.
INSPECTION OF WATER HOSE
Any water hose found in a cracked condition or flat-
tened or water leaked must be replaced.
Any leakage from the connecting section should be
corrected by proper tightening.
Radiator mounting bolt
: 8~12 Nm (0.8~1.2 kgfm) C
O
P
Y
R
I
G
H
T
E
D
5-5 COOLING SYSTEM
The voltmeter is for making sure that the battery
applies 12 volts to the motor. With the motor with
electric motor fan running at full speed, the ammeter
should be indicating not more than 5 amperes.
If the fan motor does not turn, replace the motor
assembly with a new one.
REMOVAL
Remove the radiator. (Refer to page 5-2)
Disconnect the cooling fan thermo-switch .
Remove the cooling fan.
Install the radiator.
Route the radiator hoses properly.
Pour engine coolant. (Refer to page 2-12)
Bleed air from the cooling circuit.
Install the front fender.
INSTALLATION
Install the cooling fan to the radiator.
COOLING FAN
INSPECTION
Disconnect the cooling fan motor lead wire cou-
pler and its thermo-switch lead wire coupler.
Test the cooling fan motor for load current with an
ammeter connected as shown in the illustration.
NOTE
When making above test, it is not necessary to
remove the cooling fan.
Fan motor Ammeter
Battery
B
BrW
Cooling fan mounting bolt
: 8~12 Nm (0.8~1.2 kgfm)
Cooling fan motor mounting bolt
: 8 Nm (0.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-6
COOLING FAN THERMO-SWITCH
The cooling fan is secured behind the radiator by three bolts and is automatically controlled by the thermo-switch.
The thermo-switch remains open when the temperature of the engine coolant is low, but closes when the tempera-
ture reaches approximately 88
(190
) setting the cooling fan in motion.

REMOVAL
Disconnect the cooling fan thermo-switch lead
wire coupler.
Remove the cooling fan thermo-switch .
INSPECTION
Check the thermo-switch closing or opening tem-
peratures by testing it at the bench as shown in
the figure.
Connect the thermo-switch to a circuit tester
and place it in the OIL contained in a pan, which is
placed on a stove.
Heat the oil to raise its temperature slowly and
read the column thermometer when the switch
closes of opens.
operating temperature
Standard
OFF ON
ON OFF
Approx. 95
(203
)
Approx. 88
(190
)
CAUTION
Take special care when handling the thermo-
switch.
It may cause damage if it gets a sharp impact.
Do not contact the cooling fan thermo-switch
and the column thermometer with a pan.
Oil
Multi circuit tester set : 09900-25008

C
O
P
Y
R
I
G
H
T
E
D
5-7 COOLING SYSTEM
INSTALLATION
Install the cooling fan thermo-switch in the reverse
order of removal.
Install a new O-ring and apply engine coolant
to the O-ring.
Tighten the cooling fan thermo-switch to the speci-
fied torque.
: 13 Nm (1.3 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-8
INSTALLATION
Install the water temperature switch in the reverse
order of removal.
Install a new O-ring and apply engine coolant
to the O-ring.
Tighten the water temperature switch to the speci-
fied torque.
: 13 Nm (1.3 kgfm)
WATER TEMPERATURE
SWITCH
REMOVAL
Disconnect the water temperature switch lead wire
coupler.
Remove the water temperature switch .
INSPECTION
Check the engine coolant temperature by testing it
at the bench as shown in the figure. Connect the
water temperature switch to a circuit tester and
place it in the WATER contained in a pan, which is
placed on a stove.
Heat the water to raise its temperature slowly and
read the column thermometer and the ohmmeter.
If the resistance noted to show infinity or too much
different resistance value, replace the water tempera-
ture switch with a new one.
CAUTION
Take special care when handling the water
temperature switch. It may cause damage if it
gets a sharp impact.
Do not contact the water temperature switch
and the column thermometer with a pan.
Water
Multi circuit tester set : 09900-25008

operating temperature
Standard
OFF ON
ON OFF
Approx. 120
(248
)
Approx. 113
(235
)
C
O
P
Y
R
I
G
H
T
E
D
5-9 COOLING SYSTEM
THERMOSTAT
REMOVAL
Remove the front fender.
(Refer to page 7-3)
Place a rag under the thermostat case.
Remove the thermostat case cap.
Remove the thermostat .
INSPECTION
Inspect the thermostat pellet for signs of cracking.
Test the thermostat at the bench for control action, in
the follwing manner.
Pass a string between flange, as shown in the
photograph.
Immerse the thermostat in the WATER contained
in a beaker, as shown in the illustration.
Note that the immersed thermostat is in suspen-
sion.
Heat the water by placing the beaker on a stove
and observe the rising temperature on a ther-
mometer .
Read the thermometer just when opening the ther-
mostat.
This reading, which is the temperature level at
which the thermostat valve begins to open, should
be within the standard value.
Thermostat valve
operation temperature
Valve opening
Valve closing
Standard
76
(169
)
71
(160
)
Water
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-10
Keep on heating the water to raise its tempera-
ture.
Just when the water temperature reaches speci-
fied value, the thermostat valve should have lifted
by at least 8.0 mm (0.32 in).
A thermostat failing to satisfy either of the two
requirements, start-to-open temperature and valve
lift, must be replaced with a new one.
INSTALLATION
Install the thermostat in the reverse order of removal.
Apply engine coolant to the rubber seal on the
thermostat.
Install the thermostat .
Install the thermostat case cap .
Tighten the thermostat case bolts to the specified
torque.
Standard
Over 8.0 mm at 90
(Over 0.32 in at 194
)
Thermostat valve lift
Thermostat case bolt

: 10 Nm (1.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
5-11 COOLING SYSTEM
WATER PUMP
REMOVAL AND DISASSEMBLY
Disconnect the water hoses.
Disconnect the rear brake switch spring and rear
brake pedal spring as to lower side.
Remove the rear brake master cylinder mounting
bolts.
Remove the clutch cover with pushing down the
rear brake pedal.
NOTE
Before draining engine oil and engine coolant,
inspect engine oil and coolant leakage between
the water pump and clutch cover.
If engine oil is leaking, visually inspect the oil seal
and O-ring. If engine coolant is leaking, visually
inspect the O-ring.
WARNING
Do not open the radiator cap when the engine
is hot, as you may be injured by escaping hot
liquid or vapor.
The engine must be harmful if swallowed or if it
comes in contact with the skin or eyes.
If engine coolant gets into the eyes or contacts
the skin, flush the eyes or wash the skin thor-
oughly, with plenty of water. If engine coolant
is swallowed, induce vomiting and call a physi-
cian immediately.
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-12
Remove the circlip and water pump driven gear
.
Remove the pin and washer .
Remove the water pump case from the clutch
cover.
Remove the O-rings .
C
O
P
Y
R
I
G
H
T
E
D
5-13 COOLING SYSTEM
Remove the E-ring from the impeller shaft.
Remove the impeller from the other side.
Remove the bearing.
INSPECTION
BEARING
Inspect the play of the bearing by hand while it is in
the water pump case.
Rotate the inner race by hand to inspect abnormal
noise and smooth rotation.
Replace the bearing if there is anything unusual.
NOTE
If there is no abnormal noise, bearing removal is
not necessary.
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-14
BEARING CASE
Visually inspect the bearing case for damage.
Replace the water pump body if necessary.
IMPELLER
Visually inspect the impeller and its shaft for damage.
REASSEMBLY AND INSTAL-
LATION
Instal l the water pump i n the reverse order of
removal.
Install the bearing.
Install the impeller to the water pump body.
Apply SUPER GREASE Ato the impeller shaft.
SUPER GREASE A
C
O
P
Y
R
I
G
H
T
E
D
5-15 COOLING SYSTEM
Apply engine coolant to the O-ring .
Install a new O-ring.
Connect the water hoses.
Pour engine oil. (Refer to page 2-11)
Install the rear brake master cylinder mounting
bolts.
Connect the rear brake switch spring and rear
brake pedal spring as to lower side.
Fix the impeller shaft with the E-ring .
Fill the bearing with engine oil until engine oil
comes out from the hole of the bearing housing.
CAUTION
Use a new O-ring to prevent engine coolant
leakge.
Rear brake master cylinder mounting bolt
: 8~12 Nm (0.8~1.2 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-16
OIL TANK AND HOSES
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
5-17 COOLING SYSTEM
REMOVAL
Remove the radiator. (Refer to page 5-2)
Remove the engine under cover .
Remove the oil hoses.
C
O
P
Y
R
I
G
H
T
E
D
COOLING SYSTEM 5-18
Remove the oil tank.
REMOUNTING
Remount the oil tank and hoses in the reverse order
of removal.
Tighten the engine oil inlet hose union bolts to
: 23 Nm (2.3 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
5-19 COOLING SYSTEM
Install the new O-ring to the hoses.
Install the gaskets .
Apply engine oil to the O-ring and gaskets.
Install the radiator. (Refer to page 5-4)
CAUTION
Use the new O-rings to prevent engine coolant
leakage.
C
O
P
Y
R
I
G
H
T
E
D
LOCATION OF ELECTRICAL COMPONENTS 6
-
1
IGNITION SYSTEM 6
-
3
CHARGING SYSTEM 6
-
7
STARTER SYSTEM 6
-
9
SWITCHES 6
-
12
LAMPS 6
-
14
BATTERY 6
-
16
ELECTRICAL SYSTEM
6
CONTENTS
C
O
P
Y
R
I
G
H
T
E
D
6-1 ELECTRICAL SYSTEM
LOCATION OF ELECTRICAL COMPONENTS
Left handlebar switch Ignition coil Cooling fan motor relay
Head lamp relay
Horn Magneto
Gear position switch
Igniter
Regulator / Rectifier
Turn signal relay Starter relay
C
O
P
Y
R
I
G
H
T
E
D
ELECTRICAL SYSTEM 6-2
Battery Front brake lamp switch Cooling fan motor
Main fuse Rear brake lamp switch Starter motor
C
O
P
Y
R
I
G
H
T
E
D
IGNITION SYSTEM
INSPECTION
SPARK PLUG
Clean the plug with a wire brush and pin. Use the pin
to remove carbon, taking care not to damage the
porcelain.
Check the gap with a thickness gauge.
Spark plug gap
0.7 0.8 mm
(0.028 0.032 in)
0.7 0.8 mm
(0.028 0.032 in)
I
G
N
I
T
I
O
N

C
O
I
L
I
G
N
I
T
E
R
IG. S/W
FUSE
REG
REC
BATTERY
12V 8Ah
G
L
Y
Y
Y
C
O
P
Y
R
I
G
H
T
E
D
Standard
G-L 90 ~ 110
Y-Y 0.3 ~ 0.8
Stator coil resistance

Pick-up coil
Charging coil
MAGNETO
Using the pocket tester, measure the resistance
between the lead wires in the following table.
If the resistance is not within the specified value,
replace the stator coil, with a new one.
CAUTION
When mounting the stator on the magneto cover,
apply a small quantity of THREAD LOCK 1324
to the threaded parts of screws.
WIRE COLOR
L : Blue
G : Green
Y : Yellow
Br : Brown
BY : Black with Yellow tracer
OB : Orange with Black tracer
BW : Black with White tracer
WL : White with Blue tracer
YG : Yellow with Green tracer
THREAD LOCK 1324
Pocket Tester : 09900-25002
C
O
P
Y
R
I
G
H
T
E
D
IGNITION COIL
(Checking with Pocket Tester)
Remove the front fender, side cover, fuel tank.
(Refer to page 7-3 and 4-1)
Disconnect the ignition coil lead wires and spark
plug cap, and remove the ignition coil.
Measure the ignition coil resistance in both the pri-
mary and secondary windings using a pocket tester
or an ohmmeter.
If the resistance in both the primary and secondary
windings is close to the specified values, the wind-
ings are in sound condition.
IGNITION COIL
Remove the front fender, side cover, fuel tank.
Pull out the spark plug.
Place it on the cylinder head after installing it at
the plug cap to obtain ground.
Push the electric starter switch to rotate the starter
motor, to have the test of sparking performance.
If spark doesnt emit or the spark bring out the
orange color, replace the ignition coil.
Plug cap
Pocket tester : 09900-25002
Unit :

TESTER PROBE
T
E
S
T
E
R
P
R
O
B
E
3.9~5.3
12.6~17.0
3.9~5.3
12.6~17.0

12.6~17.0 12.6~17.0
C
O
P
Y
R
I
G
H
T
E
D
CAUTION
Numberical value may differ a little according
to the tester.
Notice that there may be a defect which can
not be identified even though the measure-
ment by using the tester indicates a low volt-
age.
The range of measurement adjust a [ X 1
]
unit.
IGNITER
Using the pocket tester (R 1
range), measure
the resistance between the terminal in the following
table.
Unit : k

TESTER PROBE

7965~10775 7959~10764 16116~21804
4463~6037 4437~6003 9894~13386
2.6~3.6 3120~4220
2.6~3.6 3145~4255

T
E
S
T
E
R
P
R
O
B
E
C
O
P
Y
R
I
G
H
T
E
D
INSPECTION
CHARGING OUTPUT CHECK
Start the engine and keep it running at 5,000 rpm.
Using the pocket tester, measure the DC voltage
between the battery terminal and .
If the voltage is not within the specified value, check
the magneto no-load performance and regulator /
rectifier.
CHARGING SYSTEM
13.515.0V (at 5,000 rpm) Standard charge
CAUTION
When making this test, be sure that the battery is
full-charged condition.
Regulator
Rectifier
DCV
Battery
IG. switch
A. C generator
IG. switch
IC
B
a
t
t
e
r
y
L
O
A
D
Regulator / Rectifier
C
O
P
Y
R
I
G
H
T
E
D
MAGNETO NO-LOAD PERFORMANCE
Disconnect the three lead wires from the magneto
terminal.
Start the engine and keep it running at 5,000 rpm.
Using the pocket tester, measure the AC voltage
between the three lead wires.
If the voltage is under the specified value, replace the
magneto with a new one.
Over 70 V (at 5,000 rpm)
Standard NO-load per-
for-mance of magneto
REGULATOR / RECTIFIER
Remove the rear fender. (Refer to page 7-5)
Remove the regulator / rectifier.
Using the pocket tester (1
M
range), measure
the resistance between the terminals in the follow-
ing table.
If the resistance checked is incorrect, replace the
regulator / rectifier.
34
34
12
12
34
34
12
12
34
34
12
12
12
12
12
32
12
12
12
32
Tester probe
T
e
s
t
e
r
p
r
o
b
e
Unit :
M

C
O
P
Y
R
I
G
H
T
E
D
STARTER SYSTEM
STARTER SYSTEM DESCRIPTION
This ATV can only start the engine with pulling the clutch lever.
Clutch
lever
position
switch
Starter
switch
Ignition
switch
Fuse
B
a
t
t
e
r
y
Starter
relay
Starter
motor
Igniter
C
O
P
Y
R
I
G
H
T
E
D
COMMUTATOR
Inspect discoloration, abnormal wear or undercut
of the commutator.
If the commutator is abnormally worn, replace the
armature with a new one.
When surface is discolored, polish it with #400 sand
paper and clean it with dry cloth.
ARMATURE COIL INSPECTION
Check continuity between each segment.
Check continuity between each segment and the
armature shaft.
If there is no continuity between the segments or
there is continuity between the segment and shaft,
replace the starter motor with a new one.
Segment
STARTER MOTOR I NSPEC-

TION
CARBON BRUSH
Inspect the carbon brush for abnormal wear, crack or
smoothness in the brush holder.
If any damage are found, replace the brush assembly
with a new one.
STARTER MOTOR REMOVAL
AND DISASSEMBLY
Disconnect the starter motor lead wire.
With loosening the bolts , remove the starter
motor.
Remove the starter motor.
C
O
P
Y
R
I
G
H
T
E
D
Align the match mark on the housing with the
line on the housing end.
Apply SUPER GREASE Ato the O-ring and
remount the starter motor.
STARTER MOTOR REASSEMBLY
Reassemble the starter motor. Pay attention to the following points :
Reassembly the starter motor as shown in the illustration.
SUPER GREASE A

C
O
P
Y
R
I
G
H
T
E
D
SWITCHES
Measure each switch for continuity using a tester. If any abnormality is found, replace the respective switch
assemblies with new ones.
R O
ON
OFF
IGNITION SWITCH
O

WB
ON
OFF
FRONT / REAR BRAKE LAMP SWITCH
R
N
O

YR
PUSH
OFF
STARTER SWITCH
G

O
PUSH
OFF
HORN SWITCH
YW Y W
LIGHT & DIMMER SWITCH

Sb

Gr
HAZARD WARNING SWITCH
Lg Sb B
TURN SIGNAL SWITCH
GR L EARTH
GEAR POSITION SWITCH

C
O
P
Y
R
I
G
H
T
E
D
LAMPS
HEAD LAMP
HEAD LAMP BULB REPLACE-
MENT
Remove the front fender bolts.
Move the front fender upward to get enough space
to remove the head lamp bulb.
Remove the dust cover and socket spring.
After removing the bulb at socket, replace the new
bulb.
To i nstal l the head l amp, reverse the above
sequence.
CAUTION
If you touch the bulb with your bare hands, clean the bulb with a cloth moistened with alcohol or soapy
water to prevent premature bulb failure.
C
O
P
Y
R
I
G
H
T
E
D
BRAKE / TAIL LAMP
BRAKE / TAIL LAMP REPLACEMENT
This ATVs brake / tail lamp is LED(Light Emitting
Diode) type.
If any abnormal condition are found, replace the
brake / tail lamp assembly.
BRAKE / TAIL LAMP : LED type
TURN SIGNAL LAMP BULB REPLACEMENT
Remove the lens by removing the screw .
Push the bulb, turn it to the counter-clockwise,
and pull it out.
After stick in the new lamp, assemble the lens.
TURN SIGNAL LAMP
CAUTION
If you touch the bulb with your bare hands, clean
the bulb with a cloth moistened with alcohol or
soapy water to prevent premature bulb failure.
CAUTION
Overtightening the screws may cause the lens to
crack.
C
O
P
Y
R
I
G
H
T
E
D
COMBINATION METER
Remove the combination meter.
Disassemble the combination meter as shown in the
illustration.
INSPECTION
Using the pocket tester, check the continuity between
lead wires (Blue color coupler) in the following illus-
tration.
If the continuity measured incorrect, replace the
respective part.
CAUTION
When making this test, it is not necessary to
remove the combination meter.
C
O
P
Y
R
I
G
H
T
E
D
BATTERY
CAUTION OF BATTERY TREATMENT
The battery needs attention generally as it occur flammability gas.
If you dont follow the instruction in the below, there may be a explosion and severe accident.
Therefore, pay attention to the following points.
Positively prohibit battery from contacting to short, spark or firearms.
The recharge of battery should be done in the wide place where the wind is well ventilated.
Dont recharge it at the sight of windproof.
CAUTION OF BATTERY ELECTROLYTE TREATMENT
Pay attention to the battery electrolyte not to stains the chassis or the humanbody.
If stains the chassis or the humanbody, at once wash a vast quantity of water.
When they were stained, clothes will come into being a hole or painting will take off.
Consult a doctor.
When the battery electrolyte was dropped to the surface of land, wash it with a vast quantity of water.
Neutralize by hydroxide, bicarbonate of soda and so on.
FILLING ELECTROLYTE
Put the battery on even land and remove the alu-
minum tape sealing.
Remove the cap at the electrolyte container.
Aluminum tape
Filler holes
CAUTION
Do not remove the seal of the electrolyte contain-
er, not prick with sharp thing.
CAUTION OF MAINTENANCE
FREE BATTERY TREATMENT
Do not remove the aluminum tape to seal the bat-
tery electrolyte filler hole until use as battery of
complete seal type.
Do not use it except the battery electrolyte.
Pouring into the battery electrolyte, necessarily
use the electrolyte of the specified capacity.
Do not open the sealing cap after recharging the
battery electrolyte.
C
O
P
Y
R
I
G
H
T
E
D
Seal
Cap
Air bubble
Pouring of battery electrolyte
When insert the nozzles of the electrolyte container
into the batterys electrolyte filler holes, holding the
container firmly so that it does not fall.
Take precaution not to allow any fluid to spill.
Confirmation of pour
Make sure that air bubbles are coming up each elec-
trolyte container, and keep this position for more than
about 20 minutes.
CAUTION
The pouring of electrolyte may not be done if the
electrolyte container is pushed slopely.
CAUTION
If no air bubbles are coming up from a filler port,
tap the bottom two or three times.
C
O
P
Y
R
I
G
H
T
E
D
Insert the caps firmly
Separation of electrolyte container
After confirming that you entered the electrolyte into
battery completely, remove the electrolyte containers
from the battery.
Insert the caps
Insert the cap into the filler holes, pressing it firmly so
that the top of the caps do not protrude above the
upper surface of the batterys top cover.
SERVICING
Visually inspect the surface of the battery container. If
any signs of cracking or electrolyte leakage from the
sides of the battery have occurred, replace the battery
with a new one. If the battery terminals are found to be
coated with rust or an acidic white powdery substance,
then this can be cleaned away with sandpaper.
RECHARGING OPERATION
Using the pocket tester, check the battery voltage.
If the voltage reading is less than the 12.0 V (DC),
recharge the battery with a battery charger.
CAUTION
Draw the empty receptacle out slowly because there
may be a chance remaining electrolyte vaporize.
How to charge
Standard
Fast
0.8 A 5~10 hours
4 A 30 minutes
After recharging, wait for more than 30 minutes
and check the battery voltage with a pocket tester.
If the battery voltage is less than the 12.5V,
recharge the battery again.
If battery voltage is still less than 12.5V, after
recharging, replace the battery with a new one.
When the vehicle is not used for a long period,
check the battery every 1 month to prevent the
battery discharge.
CAUTION
When recharging the battery, remove the battery
from the vehicle.
NOTE
Do not remove the caps on the battery top while
recharging.
CAUTION
Be careful not to permit the charging current to
exceed 4A at any time.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS
EXTERIOR PARTS 7- 1
FRONT AND REAR WHEELS 7
-
7
FRONT BRAKE 7-13
FRONT SUSPENSION 7
-
21
STEERING 7
-30
REAR BRAKE 7
-41
REAR SHOCK ABSORBER 7-54
REAR SUSPENSION 7-59
REAR AXLE 7-66
CONTENTS
7
C
O
P
Y
R
I
G
H
T
E
D
7-1 CHASSIS
EXTERIOR PARTS
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-2
C
O
P
Y
R
I
G
H
T
E
D
7-3 CHASSIS
REMOVAL
SEAT
Remove the seat by pulling the lock release lever
which is located behind the rear fender.
FRONT FENDER
Disconnect the head lamp coupler .
Remove the seat. (Refer to above)
Remove the center front fender mounting bolts.
Remove the center front fender .
Remove the fuel tank cap .
Remove the center rear fender mounting bolts.
Remove the center rear fender .
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-4
Remove the four steering head cover bracket
bolts.
Remove the side covers , left and right.
FOOTREST MUDGUARD
Remove the mudguards .
Remove the front fender mounting bolts.
Remove the front fender .
C
O
P
Y
R
I
G
H
T
E
D
7-5 CHASSIS
FOOTREST
Remove the footrest mudguards.
(Refer to page 7-4)
Remove the footrests.
REAR FENDER
Remove the battery plate.
Disconnect the battery lead wires .
Remove the battery .
Remove the rear fender mounting bolts.
Remove the rear fender.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-6
REMOUNTING
Remount the exterior parts in the reverse order of
removal.
FOOTREST
Apply THREAD LOCK 1324 to the bolts and
tighten bolts to the specified torque.
MUDGUARD BRACE
Apply THREAD LOCK 1324 to the mudguard
brace bolts .
THREAD LOCK 1324
THREAD LOCK 1324
Footrest mounting bolt
: 40~60 Nm (4.0~6.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-7 CHASSIS
FRONT AND REAR WHEELS
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-8
REMOVAL
FRONT AND REAR WHEELS
Place the vehicle on level ground.
Support the vehicle with a jack or wooden block.
Remove the wheel.
FRONT WHEEL HUB
Remove the front wheel. (Refer to above)
Remove the front hub plate .
Remove the cotter pin, then loosen the wheel hub
nut.
Remove the wheel hub nut and washer.
Remove the front brake caliper.
Remove the disk. (Refer to page 7-18)
Remove the front wheel hub .
CAUTION
Do not operate the brake lever while removing the
caliper.
C
O
P
Y
R
I
G
H
T
E
D
7-9 CHASSIS
REAR WHEEL HUB
Remove the rear wheel.
Remove the cotter pin and loosen the wheel hub
nut by applying the rear brake.
Remove the wheel hub nut and washer.
Remove the rear wheel hub .
INSPECTION AND DISASSEMBLY
DUST SEAL
Inspect the dust seal lips for wear or damage.
If any damages are found, replace the dust seal with
a new one.
Remove the spacer .
Remove the dust seal with the special tool.
HUB BEARINGS
Inspect the inner race play of the hub bearing by
hand while it is in the wheel hub.
Rotate the inner race by hand to inspect for abnormal
noise and smooth rotation. If there is anything unusu-
al, replace the bearing with a new one.
CAUTION
Replace the removed dust seal with a new one.
Oil seal remover : 09913-50121
play play
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-10
Remove the hub bearing .
REASSEMBLY AND REMOUNTING
FRONT WHEEL HUB
Apply SUPER GREASE A to the hub bearing.
Install the hub bearings and spacer into the front
wheel hub.
Install the dust seal into the front wheel hub
with fabric portion facing to outside.
Apply SUPER GREASE A to the dust seals lip.
CAUTION
Do not reuse the removed bearings.
SUPER GREASE A
SUPER GREASE A
NOTE
Install the inner bearing first, and then install
the spacer and the outer bearing .
GREASE
C
O
P
Y
R
I
G
H
T
E
D
7-11 CHASSIS
SUPER GREASE A
SUPER GREASE A
Install the front disk to the front wheel hub.
Apply SUPER GREASE A to the front axle.
Install the wheel hub.
Install the front brake caliper. (Refer to page 7-17)
Tighten the front wheel hub nut to the specified
torque.
Install the hub plate .
Install the cotter pin into the front axle.
Install the front wheel.
REAR WHEEL HUB
Apply small amount of SUPER GREASE A to
the wheel hubs spline.
CAUTION
Replace the removed cotter pin with a new one.
Front wheel hub nut
: 55 Nm (5.5 kgfm)
Install the cotter pin into the rear axle.
Install the rear wheel.
Install the rear wheel hub , washer and nut.
Tighten the rear wheel hub nut to the specified
torque.
CAUTION
Rear wheel hub nut
: 100 Nm (10.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-12
FRONT WHEEL
Install the front wheel.
Tighten the wheel set nuts to the specified torque.
REAR WHEEL
Install the rear wheel.
Tighten the wheel set nuts to the specified torque.
TIRE
Refer to page 2-18
NOTE
When installing the front wheel, make sure that
the arrow on the tire points in the direction of
rotation.
NOTE
When installing the rear wheel, make sure that the
arrow on the tire points in the direction of
rotation.
Wheel set nut
: 39.2~58.8 Nm (3.92~5.88 kgfm)
Wheel set nut
: 39.2 ~ 58.8 Nm (3.92 ~ 5.88 kgfm)
ON-ROAD type
ON-ROAD type
C
O
P
Y
R
I
G
H
T
E
D
7-13 CHASSIS
FRONT BRAKE
CONSTRUCTION
CAUTION
Handle brake fluid with care : the fluid reacts chemically with paint, plastics, rubber materials etc. and will dam-
age them severly.
WARNING
This brake system is filled with an ethylene glycol-based DOT4 brake fluid. Do not use or mix different types
of fluid, such as silicone-based or petroleum-based brake fluids.
Do not use any brake fluid taken from old, used or unsealed containers. Never reuse brake fluid left over
from the last servicing or stored for a long periods.
When storing brake fluid, seal the container completely and keep away from children.
When replenishing brake fluid, take care not to get dust into the fluid.
When washing brake components, use new brake fluid. Never use cleaning solvent.
A contaminated brake disk or brake pad reduces braking performanec. Discard contaminated pads and
clean the brake disk with high quality brake cleaner or a neutral detergent.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-14
BRAKE PAD REPLACEMENT
Remove the front wheel. (Refer to page 7-8)
Remove the brake caliper mounting bolts and
brake pad mounting pins .
Remove the brake pads.
Install the new brake pads.
Tighten the brake pad mounting pins and brake
caliper mounting bolts to the specified torque.
CAUTION
Do not operate the brake lever during or after
brake pad removal.
Replace the brake pads as a set, otherwise
braking performance will be adversely affected.
NOTE
Before installing the new pads, inspect the pad
mounting pins for wear. If excessive wear is
found, replace them with new ones.
The E-ring must be installed to the caliper.
NOTE
After replacing the brake pads, pump the brake
lever several times to check for proper brake
operation and then check the brake fluid level.
Front brake pad mounting pin
: 18~28 Nm (1.8~2.8 kgfm)
Brake caliper mounting bolt
: 18~28 Nm (1.8~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-15 CHASSIS
BRAKE FLUID REPLACEMENT
Place the vehicle on a level surface and keep the
handlebar straight.
Remove the master cylinder reservoir cap and
diaphragm.
Suck up the old brake fluid as much as possible.
Fill the reservoir with new brake fluid.
Connect a clear hose to the air bleeder valve and
insert the other end of the hose into a receptacle.
Loosen the air bleeder valve and pump the brake
lever until the old brake fluid is completely out of
the brake system.
Close the air bleeder valve and disconnect the
clear hose. Fill the reservoir with new brake fluid
to the upper end of the inspection window.
BRAKE CALIPER REMOVAL
AND DISASSEMBLY
Disconnect the brake hose from the brake caliper
by removing the brake hose union bolt and
allow the brake fluid to drain into a suitable recep-
tacle.
Remove the brake caliper by removing the brake
caliper mounting bolts .
Remove the brake pads. (Refer to page 7-14)
CAUTION
Never reuse the brake fluid left over from previ-
ous servicing or stored for long periods.
Bleed air from the brake system.
WARNING
Brake fluid, if it leaks, will interfere with safe run-
ning and discolor painted surfaces. Check the
brake hose, brake pipe and hose joints for cracks
and leakage of brake fluid.
Brake air bleeder valve
: 9~14 Nm (0.9~1.4 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-16
Remove the brake pad spring and brake caliper
holder .
Using an air gun, push out the brake caliper pis-
ton.
Remove the dust seal and piston seal .
BRAKE CALIPER INSPECTION
Inspect the brake caliper cylinder wall and piston sur-
face for scratch, corrosion or other damages.
If any abnormal condition is noted, replace the
caliper.
WARNING
Place a rag over the piston to prevent it from
popping out and flying and keeping hand off
the piston.
Be careful of brake fluid which can possibly
splash.
Do not use high pressure air but increase the
pressure gradually.
CAUTION
Care not to cause scratch on the cylinder bore.
Do not reuse the piston seal and dust seal that
have been removed.
C
O
P
Y
R
I
G
H
T
E
D
7-17 CHASSIS
BRAKE CALIPER REASSEM-
BLY AND REMOUNTING
Reassemble and remount the brake caliper in the
reverse order of removal and disassembly proce-
dures and observe the following points.
Install the brake pad spring.
Apply SILICONE GREASE to the brake caliper
holder pin.
Tighten the brake pad mounting pins , brake
caliper mounting bolts and brake hose union
Install the brake pads. (Refer to page 7-14)
Fill the system with brake fluid and bleed air.
Inspection after reassembly : Refer to page 2-16
CAUTION
Wash the brake caliper components with fresh
brake fluid before reassembly. Do not wipe off
brake fluid with a rag after washing the compo-
nents.
Replace the piston seal and dust seal into new
ones with brake fluid applied.
Brake fluid specification and classification
: DOT 4
SILICONE GREASE
NOTE
Before remounting the brake caliper, push the
brake caliper pistons all way into the caliper.
Front brake pad mounting pin
: 18~28 Nm (1.8~2.8 kgfm)
Front brake caliper mounting bolt
: 18~28 Nm (1.8~2.8 kgfm)
Front brake hose union bolt
: 40~60 Nm (4.0~6.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-18
BRAKE DISK REMOVAL AND
DISASSEMBLY
Remove the front wheel hub. (Refer to page 7-8)
Remove the brake disk.
BRAKE DISK INSPECTION
Remove the caliper. (Refer to page 7-15)
Check the brake disk for damage or cracks.
Measure the thickness using the micrometer.
Replace the brake disk if the thickness is less than
the service limit or if damage is found.
Measure the runout using the dial gauge.
Replace the brake disk if the runout exceeds the ser-
vice limit.
Apply THREAD LOCK 1324 to the brake disk
bolts and tighten them to the specified torque.
If either measurement exceeds the service limit,
replace the brake disk. (Refer to above)
Brake disk thickness
Service limit
3.0 mm (0.12 in)
Brake disk runout
Service limit
0.3 mm (0.012 in)
NOTE
Make sure that the disk is clean and free of any
greasy matter.
Micrometer(025 mm) : 09900-20201
Dial gauge : 09900-20606
Brake disk bolt
: 18~28 Nm (1.8~2.8 kgfm)
THREAD LOCK 1324
BRAKE DISK REASSEMBLY
AND REMOUNTING
Reassemble and remount the brake disk in the
reverse order of removal and disassembly.
Install the disk to the wheel hub.
C
O
P
Y
R
I
G
H
T
E
D
7-19 CHASSIS
MASTER CYLINDER DISAS-
SEMBLY
Drain brake fluid out of the master cylinder.
Disconnect the brake lamp switch lead wire cou-
pler.
Remove the union bolt .
Remove the two mounting bolts and take off the
master cylinder.
Remove the two fitting screws and separate the
cap and diaphragm.
Detach the dust seal boot and remove the cir-
clip.
Pull out the piston/cup set and spring .
CAUTION
Place a rag under the union bolt so that brake
fluid can not contact the parts.

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-20
MASTER CYLINDER INSPECTION
Inspect the master cylinder bore for any scratches or
other damage.
Inspect the piston surface for any scratches or other
damage.
MASTER CYLINDER REASSE-
MBLY AND REMOUNTING
Reassemble and remount the master cylinder in the
When remounting the master cylinder to the han-
dlebar, first tighten the mounting bolts for upside
as shown.
CAUTION
Wash the master cylinder components with
new brake fluid before reassembly.
When washing the components, use the speci-
fied brake fluid. Never use different types of
fluid or cleaning solvents such as gasoline,
kerosine, etc.
Brake fluid specification and classification
: DOT 4
NOTE
When installing the circlip, make sure that the
sharp edge of the circlip faces outside.
WARNING
Bleed air from the brake fluid circuit after
assembling master cylinder. (Refer to page 2-17)
Tighten the brake hose union bolt to the speci-
fied torque.
Front brake master cylinder mounting bolt
: 5~8 Nm (0.5~0.8 kgfm)
Brake hose union bolt
: 40~60 Nm (4.0~6.0 kgfm)
Up
Master Cylinder
Handlebar
Clearance
C
O
P
Y
R
I
G
H
T
E
D
7-21 CHASSIS
FRONT SUSPENSION
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-22
REMOVAL
Remove the front wheel (Refer to page 7-8)
Remove the front wheel hub. (Refer to page 7-8)
Remove the brake caliper. (Refer to page 7-15)
Remove the front disk cover .
Remove the cotter pin and tie rod end nut.
Remove the front grip .
CAUTION
C
O
P
Y
R
I
G
H
T
E
D
7-23 CHASSIS
Remove the shock absorber lower mounting bolt
.
Remove the suspension arm assembly .
Remove the shock absorber upper mounting bolt
.
Remove the shock absorber .
Remove the cotter pins and nuts.
Remove the steering knuckle .
Remove the spacers , dust seals and bear-
ings from the suspension arm.
Remove the dust caps , dust seals , bearings
and spacers from the suspension arm.
UPPER
LOWER

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-24
FRONT SHOCK ABSORBER
Inspect the shock absorber for oil leakage or dam-
age. If any damages are found, replace the front
shock absorber with a new one.
Inspect the bearings, spacers and dust seal for wear
or damage.
I f any damages are f ound, repl ace t he shock
absorber with a new one.
KNUCKLE
Inspect the knuckle for damage. If any damages are
found, replace the knuckle with a new one.
KNUCKLE END
Inspect the knuckle end boot for wear or damage.
If any damages are found, replace the knuckle end
with a new one.
Inspect the knuckle end for smooth movement. If
there are any abnormalities, replace the knuckle end
with a new one.
SUSPENSION ARM
Inspect the suspension arm for wear or damage. If
any damages are found, replace the suspension arm
with a new one.
CAUTION
Do not attempt to disassemble the front shock
absorber. It is unserviceable.
C
O
P
Y
R
I
G
H
T
E
D
7-25 CHASSIS
SUSPENSION ARM PIVOT BEARING
Inspect the dust seal lips and spacers for wear and
damage. If any damages are found, replace them
with new ones.
Inspect the bearings for play. If excessive play is
found, replace them with a new one.
BRAKE DISK COVER
Inspect the brake disk cover for damage. If any dam-
ages are found, replace the brake disk cover with a
new one.
FRONT SHOCK ABSORBER DISPOSAL
WARNING
The front shock absorber unit contains high-
pressure nitrogen gas.
Mishandling can cause explosion.
Keep away from fire and heat. High gas pres-
sure caused by heat can cause an explosion.
Release gas pressure before disposing.
GAS PRESSURE RELEASE
Remove the valve cap.
Press the valve with a screwdriver to bleed out the
nitrogen gas.
WARNING
Releasing high pressure gas from the front
shock absorber unit can be hazardous. Never
perform any servicing until the nitrogen gas
pressure has been released from the front
shock absorber unit.
When releasing the gas pressure, place a rag
over the gas valve and use the tip of a screw-
driver to press the valve. Do not use your fin-
ger to depress the gas valve, and be sure to
direct the valve away from your face and body.
Be sure to always wear eye protection when
performing this procedure.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-26
Reassemble and remount the front suspension in the
Apply SUPER GREASE A to the dust seals, dust
covers and bearing.
Install the bearings , dust seals and spacers
into the suspension arm.
Install the spacers , bearings , dust seals
and dust caps into the suspension arm.
Degrease the tapered portion of knuckle and also
knuckle end with nonflammable cleaning solvent.
SUPER GREASE A
NOTE
Stamped mark on the dust seal must face out-
side.
Install the suspension arms to the steering knuck-
le and tighten the knuckle end nuts to the speci-
fied torque.
Install the cotter pins.
CAUTION
Replace the removed cotter pins with new ones.
Knuckle end nut : 43 Nm (4.3 kgfm)
UPPER

LOWER
C
O
P
Y
R
I
G
H
T
E
D
7-27 CHASSIS
Tighten the shock absorber mounting nut to the
specified torque.
Apply THREAD LOCK 1324 to the disk cover
mounting bolts, and then tighten the bolts.
Tighten the tie rod end nut to the specified torque.
Install the cotter pin.
CAUTION
Shock absorber mounting nut
(Upper and Lower)
: 40~60 Nm (4.0~6.0 kgfm)
THREAD LOCK 1324
Tie rod end nut
: 22~35 Nm (2.2~3.5 kgfm)
Apply THREAD LOCK 1324 to the front shock
absorber mounting bolts.
THREAD LOCK 1324
Tighten the suspension arm pivot nuts to the
specified torque.
Install the front grip and the front shock absorber.
Suspension arm pivot nut
: 40~60 Nm (4.0~6.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-28
FRONT SUSPENSION SETTING
SPRING PRE-LOAD ADJUSTMENT
The front suspension spring pre-load is adjustable.
This adjustment is performed by changing spring set
length.
Remount the front shock absorber.
Remove the front shock absorber.
Loosen the lock nut .
Adjust the spring set length by turning the adjuster
.
Tighten the lock nut .
NOTE
When installing the tie rod end, install the washer
between the nut and steering knuckle .
270 mm (10.6 in) 280 mm (11.0 in) 258 mm (10.2 in)
STANDARD
MAXIMUM
(SOFTEST)
MINIMUM
(STIFFEST)
FRONT SUSPENSION SPRING SET LENGTH
CAUTION
Do not set the spring length out of the specified
range.

C
O
P
Y
R
I
G
H
T
E
D
7-29 CHASSIS
1. Compression damping force
To adjust the compression damping force turn in the
adjuster fully for Sor Hdirection (counter-
clockwise or clockwise).
Count the number of turns from the fully turned-in
position.
Fully turned-in Hdirection (or clockwise) provides
stiffest compression damping force and turning S
direction (or counter-clockwise) the adjuster will soft-
en compression damping force.
2. Tension damping force
To adjust the tension damping force turn in the
adjuster fully for Sor Hdirection (counter-
position.
Fully turned-in Hdirection (or clockwise) provides
stiffest tension damping force and turning Sdirec-
tion (or counter-clockwise) the adjuster will soften
tension damping force.
Front shock absorber
compression damping
force adjuster
Standard
1 turn from end of S
direction (counter-clockwise)
Front shock absorber
tension damping
force adjuster
Standard
End of Sdirection
(counter-clockwise)
STANDARD FRONT SHOCK ABSORBER DAMPING FORCE
Compression Tension
Softer
Standard
Stiffer
Turn to S direction (counter-clockwise)
1 turn from end of S direction (counter-clockwise)
Turn to H direction (clockwise)
End of S direction (counter-clockwise)
WARNING
Unequal front suspension adjustment can cause
poor handling and loss of stability.
Be sure to adjust the compression and tension
damping force on the right and left front shock
absorbers to the same setting.
DAMPING FORCE ADJUSTMENT
The compression and tension damping force are
adjustable for riders preference, riders weight and
field condition.
NOTE
Do not turn the adjuster screws more than given
position, or the adjuster may be damaged.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-30
STEERING
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
7-31 CHASSIS
REMOVAL
HANDLEBAR
Remove the master cylinder assembly from the
handlebar. (Refer to page 7-19)
Remove the throttle lever case .
Disconnect the parking brake cable and the
clutch cable .
Remove the clutch switch .
Remove the handlebar switch box .
Remove the speedometer .
Remove the harness clamps .
Remove the steering head cover bracket and
the handlebar .

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-32
STEERING SHAFT AND TIE ROD
Drain engine oil and coolant.
Remove the radiator assembly .
(Refer to page 5-2)
Remove the oil tank . (Refer to page 5-17~18)
Disconnect the oil hoses and overflow hose .
Remove the cotter pins and tie rod end nuts.
Remove the tie rods.
CAUTION
C
O
P
Y
R
I
G
H
T
E
D
7-33 CHASSIS
Remove the cotter pin and steering shaft nut
and washer .
Remove the O-ring .
Remove the steering shaft holder cotter pin.
CAUTION

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-34
Remove the steering shaft holder bolts.
Remove the cable/hose guide and the steering
shaft holder.
Remove the steering shaft .
Remove the bushing and the dust seal from
the steering shaft.
Remove the steering shaft holder half.
INSPECTION
Inspect the removed parts for the following abnormal-
ities.
Handlebar distortion
Handlebar clamp wear
DUST SEALS AND O-RING
Inspect the dust seal and O-ring for wear or
damage.
If any damages are found, replace the dust seal or
O-ring with new ones.
TIE ROD
Inspect the tie rod for distortion or damage.
If any damages are found, replace the tie rod with a
new one.
C
O
P
Y
R
I
G
H
T
E
D
7-35 CHASSIS
Tie rod end
Lock nut
Lock nut
Tie rod
CAUTION
The lock nuts with a narrow width have left-
hand threads.
TIE ROD END
Inspect the tie rod ends for smooth movement.
If there are any abnormalities, replace the tie rod end
with a new one.
Inspect the tie rod end boot for wear or damage.
If any damages are found, replace the tie rod end
with a new one.
STEERING SHAFT
Inspect the steering shaft for distortion or bends.
If any damages are found, replace the steering shaft
with a new one.
STEERING SHAFT BUSHING
Inspect the steering shaft bushing for wear and
damage.
If any damages are found, replace it with a new one.
STEERING SHAFT HOLDER
Inspect the steering shaft holders for wear or dam-
age.
If any damages are found, replace the steering shaft
holders with new ones.
T
i
r
e

s
i
d
e
T
i
r
e

s
i
d
e
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-36
Reassemble and remount the steering shaft in the
STEERING SHAFT
Apply SUPER GREASE A to the O-ring, dust
seals and steering shaft before remounting the
steering shaft.
Install the dust seal and bushing to the
steering shaft.
Install the new O-ring and washer to the
steering shaft.
SUPER GREASE A
Tighten the steering shaft nut to the specified
torque.
Install the cotter pin.
Apply SUPER GREASE A to the dust seals
and sliding surface of the steering shaft holders
before remounting the steering shaft holders.
CAUTION
SUPER GREASE A
Steering shaft nut
: 49 Nm (4.9 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-37 CHASSIS
Tighten the steering shaft holder bolts to the spec-
ified torque.
Install the steering shaft holder cotter pin.
NOTE
Make sure that the wiring harness, cables and
brake hose routing are properly.
(Refer to page 8-26 to 8-31)
TIE ROD
Tighten the tie rod end nuts to the specified
torque.
Install the cotter pins.
CAUTION
Steering shaft holder bolt
: 18~28 Nm (1.8~2.8 kgfm)
Tie rod end nut
: 22~35 Nm (2.2~3.5 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-38
OIL TANK AND RADIATOR
Install the oil tank. (Refer to page 5-18)
Reinstall the radiator assembly.
(Refer to page 5-4)
Pour engine coolant and bleed air from the cooling
circuit. (Refer to page 2-12)
CAUTION
The lock nuts with a narrow width have left-
hand threads.
HANDLEBAR
Assemble the handlebar , handlebar clamp
and steering head cover bracket .
Align the punch mark on the handlebar with the
mating surface of handlebar clamp.
First tighten the bolt to the specified torque and
then tighten the bolt to the specified torque.
NOTE
The higher portion of handlebar clamp must face
forward, so that the clearance of holder is in
back of the handlebar.
Handlebar clamp bolt :
: 18~28 Nm (1.8~2.8 kgfm)
Forward

C
O
P
Y
R
I
G
H
T
E
D
7-39 CHASSIS
Install the speedometer .
Install the handle switch box with the lug on the
switch half inserted into the hole on the handle-
bar.
NOTE
When installing the handlebar, make sure that the
cable, wiring harness and brake hose routing are
proper. (Refer to page 8-26 to 31)
Install the clutch lever assembly to the handlebar
with the mating surface of clutch lever holder
aligned with punch mark on the handlebar.
Connect the clutch cable, rear brake cable and
clutch switch.
Adjust each cable play.
(Refer to page 2-9, 2-13 and 2-15)
Install the throttle case to the handlebar with the
mating surface of throttle case aligned with the
punch mark .
Tighten the throttle case bolts to the specified
torque.
Install the brake master cylinder.
Throttle case bolt : 5 Nm (0.5 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-40
TOE-IN ADJUSTMENT
Adjust the toe-in as follows :
Place the vehicle on level ground and set the han-
dlebar straight.
Make sure all the tires are inflated to the standard
pressure. (Refer to page 2-18)
Place 75 kg (165 lbs) of weight on the seat.
Loosen the lock nuts ( , ) on each tie rod.
Measure the distances ( and ) between the
front wheels. Subtract the measurements of
from the measurements of to find the toe-in.
If the toe-in is not within specification, adjust the
tie rod to the right or left until the toe-in is within
the specified range.
Temporarily tighten the four lock nuts.
Check that the distances ( and ) are equal, as
shown.
If the distances are not equal, adjust the tie rod to
the right or left until the toe-in is within specifica-
tion.
Check the toe-in again by measuring distances
and .
If the toe-in is not within specification, repeat the
adjustment as above until the proper toe-in is
obtained and distances and become equal.
After adjustment has been made, tighten the four
lock nuts to the specified torque.
CAUTION
The lock nuts have left-hand threads.
Toe-in
Standard
0 ~ 5 mm (0 ~ 0.2 in)
[ When apply to a load 75 kg (165 lbs)]
Tie rod lock nut : 29 Nm (2.9 kgfm)
NOTE
-= Toe-in
Forward
Tire side

Tire side

C
O
P
Y
R
I
G
H
T
E
D
7-41 CHASSIS
REAR BRAKE
CONSTRUCTION
WARNING
This brake system is filled with an ethylene glycol-based DOT 4 brake fluid.
Do not use or mix different types of fluid such as silicone-based or petroleum-based brake fluids.
Do not use any brake fluid taken from old, used or unsealed containers.
Never reuse brake fluid left over from the last servicing or stored for long periods.
When storing the brake fluid, seal the container completely and keep away from children.
When replenishing brake fluid, take care not to get dust into fluid.
When cleaning brake components, use fresh brake fluid. Never use cleaning solvent.
A contaminated brake disk or brake pad reduces braking performance.
Discard contaminated pads and clean the disk with high quality brake cleaner or neutral detergent.
CAUTION
Handle brake fluid with care : the fluid reacts chemically with paint, plastics, rubber materials etc, and will dam-
age them severly.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-42
BRAKE PAD REPLACEMENT
Flatten the lock washer , and then slightly
loosen the pad mounting pins .
Loosen the lock nut and turn out the parking
brake adjuster several turns.
Remove the caliper by removing the caliper
mounting bolts .
Remove the brake pads by removing the pad
mounting pins.
Install the new brake pad.
Tighten the pad mounting pins to the specified
torque, and then bend the lock washer.
CAUTION
Do not operate the brake pedal while dis-
mounting the pads.
Replace the brake pads as a set, otherwise
braking performance will be adversely affected.
NOTE
Before installing the new pads, inspect the pad
mounting pins for wear.
If excessive wear is found, replace them with
new ones.
Be sure to loosen the parking brake adjuster
before installing the pads.
NOTE
After replacing the brake pads, pump the brake
pedal several times to check for proper brake
operation and then check the brake fluid level.
Rear brake pad mounting pin
: 18~28 Nm (1.8~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-43 CHASSIS
Tighten the caliper mounting bolts to the specified
torque.
Adjust the parking brake. (Refer to page 2-15)
BRAKE FLUID REPLACEMENT
Place the vehicle on a level surface.
Remove the master cylinder reservoir cap and
diaphragm.
Suck up the old brake fluid as much as possible.
Fill the reservoir with new brake fluid.
Connect a clear hose to the air bleeder valve and
insert the other end of the hose into a receptacle.
Loosen the air bleeder valve and pump the brake
pedal until the old brake fluid is completely out of
the brake system.
Close the air bleeder valve and disconnect the
clear hose.
Fill the reservoir with new brake fluid to the upper
level.
: 18~28 Nm (1.8~2.8 kgfm)
Brake air bleeder valve
: 9~14 Nm (0.9~1.4 kgfm)
CAUTION
Never reuse the brake fluid left over from previ-
ous servicing and stored for long periods.
Bleed air from the brake system.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-44
BRAKE CALIPER REMOVAL
AND DISASSEMBLY
Disconnect the parking brake cable by removing
the lock nut and lever .
Disconnect the brake hose and allow the brake
fluid to drain into a suitable receptacle.
Remove the parking brake housing .
Remove the brake caliper by removing the caliper
mounting bolts .
WARNING
Brake fluid, if it leaks, will interfere with safe run-
ning and discolor painted surfaces.
Check the brake hose and hose joints for cracks
and fluid leakage.
Remove the pad. (Refer to page 7-42)
Remove the pad spring .
C
O
P
Y
R
I
G
H
T
E
D
7-45 CHASSIS
Loosen the caliper pin bolt , and then remove
the caliper holder .
Remove the caliper pin bolt .
Place a rag over the brake caliper piston to pre-
vent the piston from popping out.
Force out the piston by pushing the piston hanger
pin.
Remove the dust seal and piston seal .
CAUTION
Do not reuse the dust seal and piston seal to pre-
vent leakage of brake fluid.
BRAKE CALIPER INSPECTION
Refer to page 7-16
PARKING BRAKE
Inspect the parking brake for any damages and
smooth rotation by turning the axle. If there is any-
thing unusual, replace the parking brake with a new
one.

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-46
BRAKE CALIPER REASSEM-
BLY AND REMOUNTING
Refer to page 7-17
Reassemble and remount the brake caliper in the
PISTON SEALS
Install the piston seal and dust seal .
Tighten the brake caliper pin bolt to the speci-
fied torque.
Apply SILICONE GREASE to the brake caliper
holder pin and caliper pin bolt .
BRAKE CALIPER HOLDER
Tighten the holder pin to the caliper holder
SILICONE GREASE
Rear brake caliper pin bolt
: 23 Nm (2.3 kgfm)
Rear brake caliper holder pin
: 18 Nm (1.8 kgfm)
Install the pad spring and pads.

C
O
P
Y
R
I
G
H
T
E
D
7-47 CHASSIS
Tighten the caliper mounting bolts and brake
hose union bolt .
When replacing the boot with a new one, apply
SILICONE GREASE to the groove of parking
brake axle.
Install the parking brake housing and new gas-
ket.
Apply THREAD LOCK 1324 to the parking brake
Loosen the lock nuts , and turn the adjusters
, in completely, so that the cable play is max-
imum.
NOTE
Before remounting the brake caliper, push the
brake caliper piston all the way into the caliper.
CAUTION
The removed brake hose washers should be
replaced with new ones in order to prevent
leakage of brake fluid.
Bleed air from the system after after reassem-
bling the brake caliper. (Refer to page 2-17)
SILICONE GREASE
: 18~28 Nm (1.8~2.8 kgfm)
: 40~60 Nm (4.0~6.0 kgfm)
THREAD LOCK 1324
Parking brake housing bolt
: 28 Nm (2.8 kgfm)

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-48
Connect the parking cable .
Install the adjuster and the lock nut .
Adjust the parking brake. (Refer to page 2-15)
BRAKE DISK REMOVAL AND
REMOUNTING
Remove the rear wheel. (Refer to page 7-8)
Remove the rear axle. (Refer to page 7-67)
Install the brake disk to the rear axle.
Apply THREAD LOCK 1324 to the brake disk
Install the rear axle. (Refer to page 7-70)
Install the rear wheel. (Refer to page 7-12)
BRAKE DISK INSPECTION
Refer to page 7-18
NOTE
Make sure that the disk is free of any greasey
matter.
THREAD LOCK 1324
Brake disk bolt
: 18~28 Nm (1.8~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-49 CHASSIS
MASTER CYLINDER REMOVAL
AND DISASSEMBLY
Drain the brake fluid. (Refer to page 7-43)
Place a rag underneath the brake hose union bolt
on the master cylinder to catch any split brake
fluid.
Remove the brake hose union bolt and discon-
nect the brake hose .
Remove the rear master cylinder pin .
Loosen the master cylinder rod lock nut .
Turn the adjuster .
Remove the master cylinder mounting bolt .
Remove the master cylinder by turning the master
cylinder rod .
Disconnect the reservoir tank hose .
CAUTION
Immediately wipe off any brake fluid contacting
any part of the vehicle. The brake fluid reacts
chemically with paint, plastics, rubber materials,
etc., and will damage them severely.
MASTER CYLINDER INSPECTION
Refer to page 7-20
PRESSURE CONTROL VALVE
REMOVAL
Drain the brake fluid.
Place a rag underneath the brake hose union bolt
on the pressure control valve to catch any split
brake fluid.
Remove the brake hose union bolts and discon-
nect the brake hoses.
PRESSURE CONTROL VALVE
REASSEMBLY
Reassemble the pressure control valve in the reverse
order of removal.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-50
MASTER CYLINDER REASSEM-
BLY AND REMOUNTING
Refer to page 7-20
Reassemble and remount the master cylinder in the
Pay attention to the following point :
Apply MOLY PASTE to the master cylinder push
rod.
Install the master cylinder rod lock nut , adjuster
and rear master cylinder pin .
Tighten the master cylinder rod lock nut , mas-
ter cylinder mounting bolts and brake hose
union bolt to the specified torque.
CAUTION
The removed brake hose washers should be
replaced with new ones.
Bleed air from the system after reassembling
the brake master cylinder. (Refer to page 2-17)
MOLY PASTE
: 10~20 Nm (1.0~2.0 kgfm)
Rear brake master cylinder mounting
bolt : 8~12 Nm (0.8~1.2 kgfm)
: 40~60 Nm (4.0~6.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-51 CHASSIS
REVERSE CABLE
REMOVAL
Remove the reverse lever assembly from the
bracket.
Remove the reverse cable mounting screw.
Remove the cap .
Remove the screw .
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-52
Remove the reverse lever .
Disconnect the cable by removing the spool .
Remove the engine sprocket cover.
(Refer to page 3-3)
Disconnect the reverse cable by removing the
cable mounting screw.
REMOUNTING
Remount the reverse cable in the reverse order
removal.
Install the spring with the spring end matched
the groove on the housing.
Install the O-ring to the reverse cable .
Connect the cable to the spool through the hole
of the housing.
Apply SUPER GREASE A to the O-ring .
SUPER GREASE A
C
O
P
Y
R
I
G
H
T
E
D
7-53 CHASSIS
CABLE PLAY ADJUSTMENT
After installing the reverse cable, adjust the cable
play.
The cable adjuster is located at left downside of the
crankcase assembly.
Turn the adjuster in or out until the cable play
should be 1 ~ 2 mm (0.04 ~ 0.08 in) at the
reverse lever.
Tighten the lock nut securely.
After adjustment, be sure to check for reverse
function.
NOTE
When installing the spool, hook the spring end
on the concave portion of the spool.
Make sure that the reverse cable is routed cor-
rectly.

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-54
REAR SHOCK ABSORBER
CONSTRUCTION
REMOVAL
Raise the rear wheel off the ground and support
the vehicle with jack or wooden block.
Remove the cushion lever cover .

C
O
P
Y
R
I
G
H
T
E
D
7-55 CHASSIS
Remove the cushion rod lower bolt/nut.
Remove the rear shock absorber mounting bolts/
nuts.
Remove the rear shock absorber by lifting up the
swingarm.
INSPECTION
Inspect the shock absorber body, bearing, seals and
spacers for damage and leakage of oil.
If any defects are found, replace the shock absorber
with a new one.
CAUTION
Do not attempt to disassemble the rear shock
absorber. It is unserviceable.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-56
REAR SHOCK ABSORBER
DISPOSAL
GAS PRESSURE RELEASE
Remove the valve cap.
Press the valve with a screwdriver to bleed out the
nitrogen gas.
REMOUNTING
Remounting the rear shock absorber in the reverse
order of removal. Pay attention to the following points :
Tighten each bolt/nut to the specified torque.
WARNING
The rear shock absorber unit contains high-
pressure nitrogen gas.
Mishandling can cause explosion.
Keep away from fire and heat. High gas pres-
sure caused by heat can cause an explosion.
Release gas pressure before disposing.
WARNING
Releasing high pressure gas from the rear
shock absorber unit can be hazardous. Never
perform any servicing until the nitrogen gas
pressure has been released from the rear
shock absorber unit.
When releasing the gas pressure, place a rag
over the gas valve and use the tip of a screw-
driver to press the valve. Do not use your fin-
ger to depress the gas valve, and be sure to
direct the valve away from your face and body.
Be sure to always wear eye protection when
performing this procedure.
Rear shock absorber nut (Upper)
: 40~60 Nm (4.0~6.0 kgfm)
Rear shock absorber nut (Lower)
: 40~60 Nm (4.0~6.0 kgfm)
Rear cushion rod nut
: 70~100 Nm (7.0~10.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-57 CHASSIS
REAR SUSPENSION SETTING
SPRING PRE-LOAD ADJUSTMENT
The rear suspension spring pre-load is adjustable.
This adjustment is performed by changing spring set
length.
Remove the rear shock absorber.
Adjust the spring set length by turning the adjuster
.
Tighten the lock nut .
Remount the rear shock absorber.
REAR SUSPENSION SPRING SET LENGTH
STANDARD
MAXIMUM
(SOFTEST)
MINIMUM
(STIFFEST)
228 mm
(8.98 in )
235 mm
( 9.25 in )
213 mm
( 8.39 in )
CAUTION
Do not set the spring length out of the specified
range.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-58
2. Tension damping force
To adjust the tension damping force turn in the
adjuster fully for S or H direction (counter-
position.
Fully turned-in H direction (or clockwise) provides
stiffest tension damping force and turning S direc-
tion (or counter-clockwise) the adjuster will soften
tension damping force.
STANDARD REAR SHOCK ABSORBER DAMPING FORCE
Compression Tension
Softer
Standard
Stiffer
DAMPING FORCE ADJUSTMENT
The compression and tension damping force are
adjustable for riders preference, riders weight and
field condition.
1. Compression damping force
To adjust the compression damping force turn in the
adjuster fully for S or H direction (counter-
position.
Fully turned-in H direction (or clockwise) provides
stiffest compression damping force and turning S
direction (or counter-clockwise) the adjuster will soft-
en compression damping force.
NOTE
Do not turn the adjuster screws more than given
position, or the adjuster may be damaged.
Rear shock absorber

tension damping force
adjuster
Standard
Rear shock absorber
compression damping
force adjuster
Standard
C
O
P
Y
R
I
G
H
T
E
D
7-59 CHASSIS
REAR SUSPENSION
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-60
REMOVAL
CUSHION LEVER AND CUSHION ROD
Place the vehicle on the level ground and support
the vehicle with a jack or wooden block.
Remove the cushion lever cover .
Remove the cushion rod .
Remove the cushion lever .
REAR SWINGARM
Remove the cushion rod and cushion lever.
(Refer to above)
Remove the rear shock absorber.
Remove the rear wheels. (Refer to page 7-8)
Remove the rear axle and axle housing.
C
O
P
Y
R
I
G
H
T
E
D
7-61 CHASSIS
Remove the brake hose guide .
Loosen the swingarm pivot nut and remove the
swingarm pivot shaft.
Remove the swingarm assembly.
Remove the chain buffer .
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-62
SPACER
Remove the seals and spacers from the
swingarm.
Remove the spacers from the cushion lever and
cushion rod.
Inspect the spacers for any flaws or other dam-
age.
If any defects are found, replace the spacers with
new ones.
DUST SEAL
Inspect the dust seals for wear or damage.
If any defect are found, replace them with new
ones.
C
O
P
Y
R
I
G
H
T
E
D
7-63 CHASSIS
SWINGARM BEARING AND BUSHING
Insert the spacer into the bearing , bushing
and then check the play when moving the spacer up
and down.
If excessive play is noted, replace the bearing and
bushing with a new one.
CUSHI ON LEVER BEARI NG AND
CUSHION ROD BEARING
Insert the spacer into the bearing, and then check the
play when moving the spacer up and down.
If excessive play is neted, replace the bearing with a
new one.
SWINGARM PIVOT SHAFT
Using a dial gauge, check the pivot shaft runout.
If the runout exceeds service limit, replace the pivot
shaft with a new one.
Swingarm pivot shaft
runout
Service limit
0.6 mm (0.024 in)
Dial gauge : 09900-20606
V-block : 09900-21304
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-64
CUSHION LEVER AND ROD BOLT
Inspect the cushion lever and rod bolts for damage or
bend.
If any defect are noted, replace them with new ones.
CHAIN BUFFER
Inspect the chain buffer for wear and damage.
If any defects are found, replace the chain buffer with
a new one.
C
O
P
Y
R
I
G
H
T
E
D
7-65 CHASSIS
REMOUNTING
Remount t he cushi on l ever, cushi on rod and
swingarm in reverse order of removal.
Install the swingarm and pivot shaft.
Tighten the swingarm pivot nut to the specified
torque.
Install the rear shock absorber and cushion lever.
Tighten the rear shock absorber mounting nuts to
Tighten the cushion rod nut and cushion lever nut
Swingarm pivot nut
: 50~80 Nm (5.0~8.0 kgfm)
Rear shock absorber nut (Upper)
: 40~60 Nm (4.0~6.0 kgfm)
Rear shock absorber nut (Lower)
: 40~60 Nm (4.0~6.0 kgfm)
Cushion lever nut
: 70~100 Nm (7.0~10.0 kgfm)
Cushion rod nut
: 70~100 Nm (7.0~10.0 kgfm)

C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-66
REAR AXLE
CONSTRUCTION
C
O
P
Y
R
I
G
H
T
E
D
7-67 CHASSIS
REMOVAL
Place the vehicle on the level ground and support
the vehicle with a jack or wooden block.
SPROCKET
Remove the left rear wheel. (Refer to page 7-8)
Remove the left rear wheel hub.
(Refer to page 7-9)
Remove the rear caliper.
Loosen the chain adjuster , rear axle housing
nuts and wrench bolts .
Loosen the sprocket mounting bolts and remove
the sproket .
REAR AXLE SHAFT
Remove the rear wheel. (Refer to page 7-8)
Remove the rear wheel hub. (Refer to page 7-9)
Loosen the axle nuts by applying the rear
brake.
Remove the axle nuts.
Remove the sprocket flange .
Remove the caliper.
Draw out the rear axle shaft to the right.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-68
REAR AXLE HOUSING
Remove the axle housing bolts, nuts and wrench
bolts.
Remove the chain adjuster .
Remove the chain adjuster bolt .
Remove the axle shaft .
Remove the axle housing from the swingarms
right side.
SPROCKET
Inspect the sprocket teeth for wear.
If they are worn as shown, replace the engine
sprocket, rear sprocket and drive chain as a set.
CAUTION
Do not attempt to remove the brake disk flange
from the rear axle shaft.
The rear axle shaft is available only as an assem-
bly.
Normal wear Excessive wear
C
O
P
Y
R
I
G
H
T
E
D
7-69 CHASSIS
REAR AXLE SHAFT
Measure the rear axle shaft runout.
If the runout exceeds the service limit, replace the
rear axle shaft with a new one.
DUST SEAL
Inspect the dust seals for wear or damage. If any
defect are founds, replace the dust seal with a new
one.
AXLE BEARINGS
Inspect the play of the wheel bearings by finger while
they are in the axle housing.
Rotate the inner race by finger to inspect for abnor-
mal noise and smooth rotation.
Replace the bearing with a new one, if there is any-
thing unusual.
Rear axle
shaft runout
Service limit
6 mm (0.24 in)
NOTE
When measuring the runout, support the rear axle
shaft at 34 mm (1.34 in) diameter of the rear axle
shaft as shown in illustration.
Measure the runout at 40 mm (1.57 in) diameter of
the rear axle shaft as shown in illustration.
Dial gauge : 09900-20606
V-block : 09900-21304
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-70
REASSEMBLY AND REMOUNT-
ING
Reassemble the rear axle shaft and rear axle hous-
ing in the reverse order of removal and disassembly.
REAR SPROKET
Install the rear sprocket to the sprocket flange
.
Apply THREAD LOCK 1324 to the sprocket
mounting bolts.
Tighten the sprocket mounting bolts to the speci-
fied torque.
AXLE HOUSING
Apply SUPER GREASE A to the bearings and
dust seals before installing.
SUPER GREASE A
THREAD LOCK 1324
Rear sprocket mounting bolt
: 18~28 Nm (1.8~2.8 kgfm)
GREASE
C
O
P
Y
R
I
G
H
T
E
D
7-71 CHASSIS
Install the axle housing from the swingarms right
side.
Install the rear axle shaft .
Install the chain adjuster bolt .
Install the chain adjuster .
Tighten the axle housing bolts, nuts and wrench
bolts temporarily.
REAR AXLE SHAFT
When the rear axle shaft is replaced with a new one,
install the right axle nut onto the new axle shaft.
Apply THREAD LOCK 1324 to the axle shaft.
THREAD LOCK 1324
Install the brake disk to the rear axle shaft.
Apply THREAD LOCK 1324 to the disk bolts and
tighten them to the specified torque.
Install the rear axle shaft into the axle shaft housing.
NOTE
Make sure that the brake disk is clean and free of
any grease matter.
THREAD LOCK 1324
Disk bolt : 18~28 Nm (1.8~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS 7-72
Apply SUPER GREASE A to the spline of the
axle shaft.
Install the sprocket flange to the axle shaft.
Apply BOND 1215 to the axle shaft.
Apply THREAD LOCK 1324 to the thread portion
of the rear axle shaft.
Tighten the inner axle shaft inner nut to the
specified torque.
SUPER GREASE A
BOND 1215
THREAD LOCK 1324
Axle shaft nut (inner)
: 120~150 Nm (12.0~15.0 kgfm)
Apply THREAD LOCK 1324 to the thread portion
of the rear axle shaft.
Tighten the rear axle outer nut to the specified
torque.
THREAD LOCK 1324
Axle shaft nut (outer)
: 120~150 Nm (12.0~15.0 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
7-73 CHASSIS
Install the rear wheel hubs. (Refer to page 7-11)
Install the rear wheels. (Refer to page 7-12)
Adjust the chain slack. (Refer to page 2-21)
Tighten the rear axle housing nuts and wrench
bolts to the specified torque in the described
order. (Refer to page 2-21)
Install the rear caliper and tighten the caliper
mounting bolts to the specified torque.
: 70~100 Nm (7.0~10.0 kgfm)
: 40~60 Nm (4.0~6.0 kgfm)
Rear caliper mounting bolt
: 18~28 Nm (1.8~2.8 kgfm)
C
O
P
Y
R
I
G
H
T
E
D
SERVICING INFORMATION
TROUBLESHOOTING 8- 1
SPECIAL TOOLS 8- 9
TIGHTENING TORQUE 8-12
SERVICE DATA 8-14
WIRE AND CABLE ROUTING 8-24
WIRING DIAGRAM 8-30
CONTENTS
8
C
O
P
Y
R
I
G
H
T
E
D
8-1 SERVICING INFORMATION
TROUBLESHOOTING
ENGINE
Compression too low
1. Valve clearance out of adjustment.
2. Worn valve guides or poor seating of valves.
3. Valves mistiming
4. Piston rings excessively worn.
5. Worn-down cylinder bore.
6. Poor seating of spark plug.
7. Starter motor cranks but too slowly.
Plug not sparking
1. Fouled spark plug.
2. Wet spark plug.
3. Defective ignition coil.
4. Open or short circuit in high tension cord.
5. Defective magneto.
6. Defective igniter
No fuel reaching the carburetor
1. Clogged hole in the fuel tank cap.
2. Clogged or defective fuel cock.
3. Defective carburetor float valve.
4. Clogged fuel pipe.
2. Clogged fuel hose.
3. Clogged jets in carburetor.
5. Defective CDI unit
Excessive valve chatter
1. Valve clearance too large.
2. Weakened or broken valve springs.
3. Worn down camshaft.
Noise appears to come from piston
1. Piston or cylinder worn down.
2. Weakened or broken valve springs.
3. Worn down piston pin or piston pin bore.
4. Piston rings or ring groove worn.
Noise seems to come from camshaft drive chain
1. Stretched camshaft drive chain.
2. Worn camshaft sprockets.
3. Cam chain tensioner adjuster not working.
Noise seems to come from clutch
1. Worn splines of countershaft or hub.
2. Worn teeth of cluth plates.
3. Distorted clutch plates, driven and drive.
Noise seems to come from crankshaft
1. Worn or broken bearings.
2. Big-end bearings worn and broken.
3. Thrust clearance too large.
Adjust.
Repair or replace.
Adjust.
Replace.
Replace or rebore.
Retighten.
Consult electrical complaints
Clean or replace.
Clean and dry.
Replace.
Replace.
Replace.
Replace.
Clean.
Clean or replace.
Replace.
Clean or replace.
Clean.
Clean.
Clean.
Adjust.
Replace
Adjust.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Repair or replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Engine will not
start, or is hard
to start.
Engine stalls
easily.
Noisy engine.
Complaint Remedy Symptom and possible causes
C
O
P
Y
R
I
G
H
T
E
D
SERVICING INFORMATION 8-2
Noise seems to come from transmission
1. Gears worn or rubbing.
2. Badly worn splines.
3. Primary gears worn or rubbing.
3. Badly worn bearings.
Noise seems to come from water pump
1. Too much play on pump shaft bearing.
2. Worn or damaged impeller shaft.
3. Contact between pump case and impeller.
1. Clutch control out of adjustment or too much play.
2. Weakened clutch springs.
3. Worn or distorted pressure plate.
1. Clutch control out of adjustment or too much play.
2. Weakened clutch springs.
1. Broken gearshift cam.
2. Distorted gearshift forks.
3. Worn gearshift pawl.
1. Broken return spring on shift shaft.
2. Shift shafts are rubbing or sticky.
3. Distorted or worn gearshift forks.
1. Worn shifting gears on driveshaft or countershaft.
2. Distorted or worn gearshift forks.
3. Weakened stopper pawl spring on gearshift cam.
4. Worn gearshift pawl.
2. Poor seating of valves.
3. Defective valve guides.
4. Defective pick-up coil.
5. Spark plug gap too wide.
6. Defective ignition coil resulting in weak sparking.
7. Float-chamber fuel level out of adjustment in carburetor.
8. Clogged jets.
1. Valve springs weakened.
2. Valve timing out of adjustment.
3. Worn cams.
4. Spark plug gap too narrow.
6. Float-chamber fuel level too low.
7. Clogged air cleaner element.
8. Clogged fuel hose, resulting in inadequate fuel supply to carburetor.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Adjust.
Replace.
Replace.
Replace.
Adjust.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Repair.
Replace.
Replace.
Replace.
Replace.
Replace.
Adjust.
Replace.
Replace.
Replace.
Adjust or replace.
Replace.
Adjust.
Clean.
Replace.
Adjust.
Replace.
Repair.
Replace.
Adjust .
Clean.
Clean or replace.
Noisy engine.
Slipping clutch.
Dragging clutch.
Transmission will
not shift.
Transmission will
not shift back.
Transmission
jumps out of gear.
Engine idles
poorly.
Engine runs
poorly in high
speed range.
C
O
P
Y
R
I
G
H
T
E
D
Dirty or heavy
exhaust smoke
Engine lacks
power.
Engine
overheats.
1. Too much engine oil in the engine.
2. Worn piston rings or cylinder.
3. Worn valve guides.
4. Cylinder wall scored or scuffed.
5. Worn valves stems.
6. Defective stem seals.
7. Worn side rails.
1. Loosen of valve clearance.
2. Weakened valve springs.
3. Valve timing out of adjustment.
4. Worn piston ring or cylinder.
5. Poor seating of valves.
7. Worn camshaft.
8. Spark plug gap incorrect.
9. Clogged jets in carburetor.
10. Float-chamber fuel level out of adjustment.
11. Clogged air cleaner element.
12. Too much enging oil.
13. Defective air intake pipe.
1. Heavy carbon deposit on piston head.
2. Not enough oil in the engine.
3. Defective oil pump or clogged oil circuit.
4. Fuel level too low in float chamber.
5. Air leak from intake pipe.
6. Use of incorrect engine oil.
7. Defective cooling system.
Check with inspection win-
dow, drain out excess oil.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Adjust.
Replace.
Adjust.
Replace.
Repair or replace.
Clean or replace.
Replace.
Adjust or replace.
Clean.
Adjust.
Clean.
Drain out excess oil.
Retighten or replace.
Clean.
Add oil.
Repair or clean.
Adjust.
Retighten or replace.
Change.
See Cooling systemsection.
C
O
P
Y
R
I
G
H
T
E
D
CARBURETOR
Trouble with
starting.
1. Starter jet is clogged.
2. Starter pipe is clogged.
3. Air leaking from a joint between starter body and carburetor.
4. Starter plunger is not operating properly.
Clean.
Clean.
Check st art er body and
carburetor for ti ghtness,
adjust and replace gasket.
Check and adjust.
Medium or high
speed trouble.
1. Main jet or main air jet is clogged.
2. Needle jet is clogged.
3. Throttle valve is not operating properly.
4. Filter is clogged.
Check and clean.
Check and clean.
Check throttle valve for
operation.
Check and clean.
Idling or low-speed
trouble.
1. Pilot jet, pilot air jet are clogged or loose.
2. Pilot outlet or bypass is clogged.
3. Starter plunger is not fully closed.
Check and clean.
Check and clean.
Check and clean.
Overflow and fuel
level fluctuations.
1. Needle valve is worn or damaged.
2. Spring in needle valve is borken.
3. Float is not working properly.
4. Foreign matter has adhered to needle valve.
5. Fuel level is too high or low.
Replace.
Replace.
Check and adjust.
Clean.
Adjust float height.
RADIATOR (COOLING SYSTEM)
Engine
overheats.
1. Not enough engine coolant.
2. Radiator core clogged with dirt or scale.
3. Faulty cooling fan.
4. Defective cooling fan thermo-switch.
5. Clogged water passage.
6. Air trapped in the cooling circuit.
7. Defective water pump.
8. Use of incorrect engine coolant.
9. Defective thermostat.
Add coolant.
Clean.
Repair or replace.
Replace.
Clean.
Bleed out air.
Replace.
Replace.
Replace.
Engine
overcools.
1. Defective cooling fan thermo-switch.
2. Extremely cold weather.
3. Defective thermostat.
Replace.
Put on the radiator cover.
Replace.
C
O
P
Y
R
I
G
H
T
E
D
ELECTRICAL
No sparking or poor
sparking.
2. Defective spark plug.
3. Defective igniter
Replace.
Replace.
Replace.
Spark plug soon
become fouled with
carbon.
1. Mixture too rich.
2. Idling speed set too high.
3. Incorrect gasoline.
4. Dirty element in air cleaner.
5. Spark plug too cold.
Adjust carburetor.
Adjust carburetor.
Change.
Clean or replace.
Replace by hot type plug.
Spark plug become
fouled too soon.
1. Worn piston rings.
2. Pistons or cylinder worn.
3. Excessive clearance of valve stems in valve guides.
4. Worn stem oil seal.
Replace.
Replace.
Replace.
Replace.
Generator charge,
but charging
rate is below the
specification.
1. Lead wires tend to get shorted or open-circuited or loosely connected
at terminals.
2. Grounded or open-circuited stator coils of generator.
3. Defective regulator/rectifier.
4. Not enough electrolyte in the battery.
5. Defective cell plates in the battery.
Repair or retighten.
Replace.
Replace.
Add distilled water between
the level lines.
Replace the battery.
Generator
overcharges.
1. Internal short-circuit in the battery.
2. Resistor element in the regulator/rectifier damaged or defective.
3. Regulator/rectifier poorly grounded.
Replace.
Clean and tighten
ground connection.
Unstable
charging.
1. Lead wire insulation frayed due to vibration resulting in intermittent
shorting.
2. Generator internally shorted.
3. Defective regulator/rectifier.
Repair or replace
Replace.
Replace.
Starter switch is
not effective.
1. Battery run down.
2. Defective switch contacts.
3. Brushes not seating properly on commutator in starter motor.
4. Defective starter relay.
Recharge or replace.
Replace.
Repair or replace.
Replace.
Spark plug
electrodes
overheat or burn.
1. Spark plug too hot.
2. The engine overheats.
3. Spark plug loose.
4. Mixture too lean.
Replace by cold type plug.
Tune up.
Retighten.
Adjust carburetor.
C
O
P
Y
R
I
G
H
T
E
D
BATTERY
Sulfation acidic
white powdery
substance or spots
on surfaces of
cell plates.
1. Not enough electrolyte.
2. Battery case is cracked.
3. Battery has been left in a run-down condition for a long time.
4. Cont ami nat ed el ect rol yt e. (Forei gn mat t er has ent ers t he
battery and become mixed with the electrolyte.)
Add distilled water, if the battery
has not been damaged and
sulfationhas not advanced
too far, and recharge.
Replace the battery or recharge.
If sulfationhas not advanced
far, try to restore the battery by
r epl aci ng t he el ect r ol yt e,
recharing it fully with the battery
detached from the vehi cl e
and then adjusting electrolyte
specific gravity.
Battery runs down
quickly.
1. The charging method is not correct.
2. Cell plates have lost much of their active material as a result of
over-charging.
3. A short-circuit condition exists within the battery due to excessive
accumulation of sediments caused by the high electrolyte specific
gravity.
4. Electrolyte specific gravity is too low.
5. Contaminated electrolyte.
6. Battery is too old.
Check the generator, regulator
/rectifier and circuit connections,
and make necessary adjustments
to obtai n specified charging
operation.
Replace the battery, and correct
the charging system.
Recharge the battery fully and
adj ust el ect rol yt e speci f i c
gravity.
Replace the electrolyte, recharge
the battery and then adjust
specific gravity.
Battery sulfation
1. Charging rate too low or too high. (When not in use, batteries
should be recharged at least once a month to avoid sulfation.)
2. Battery electrolyte excessive or insufficient, or its specific gravity too
high or too low.
3. The battery left unused for too long in cold climate.
Keep the electrolyte up to the
prescribed level, or adjust the
specific gravity by consulting
the battery makers directions.
Replace the battery, if badly
sulfated.
Battery discharges
too rapidly.
1. Dirty container top and sides.
2. Impurities in the electrolyte or electrolyte specific gravity is too high.
Clean.
Change t he el ect rol yt e by
consulting the battery makers
directions.
Reversed battery
polarity.
The battery has been connected the wrong way round in the system, so
that it is being charged in the reverse direction.
Replace the battery and be
sure to connect the battery
properly.
C
O
P
Y
R
I
G
H
T
E
D
CHASSIS
Handling is too
heavy or stiff
Steering wobbles.
Steering pulls to
one side.
Shocks felt in the
steering.
Tires rapidly or
unevenly wear.
Steering too noisy.
Front suspension
too soft.
Front suspension
too stiff.
Suspension too
noisy.
Rear suspension
too soft.
Rear suspension
too stift.
Rear wheels
wobble.
1. Improper front wheel alignment.
2. Insufficiently lubricated.
3. Low air pressure in front tires.
4. Tie rod ends tending to seize.
5. Linkage connections tending to seize.
Adjust.
Lubricate.
Adjust.
Replace.
Repair or replace.
Regulate.
Tighten.
Replace.
Replace or tighten.
Replace.
Replace.
Replace.
Tighten.
Regulate.
Adjust.
Replace.
Repair or replace.
Replace.
Regulate.
Replace.
Tighten.
Replace.
Adjust.
Replace.
Replace.
Tighten.
Replace.
Tighten.
Replace.
Lubricate.
Tighten.
Replace.
Replace.
Replace.
Replace.
Adjust.
Adjust.
Replace.
Replace.
Replace.
Adjust.
Adjust.
Adjust.
Replace.
Replace.
Replace.
Tighten.
Replace.
Tighten.
Adjust.
Replace.
Replace.
Tighten.
1. Unequally inflated tires.
3. Worn front wheel hub bearings.
4. Distorted frame or suspension.
5. Defective shock absorber.
1. Unequally inflated tires.
2. Loose front wheel hub nuts.
3. Damaged or worn front wheel hub bearings.
4. Worn or loose tie rod ends.
5. Defective or incorrect front tires.
6. Damaged or worn suspension arms and related bearings.
7. Distorted front wheels.
8. Loose chassis nuts and bolts.
1. High tire pressure.
2. Worn steering linkage connections.
3. Loose suspension system bolts.
1. Worn or loose front wheel hub bearings.
1. Loose nuts and bolts.
2. Damaged or worn front wheel hub bearings.
3. Insufficiently lubricated.
1. Weakened spring.
2. Shock absorber leaks oil.
1. Worn upper or lower suspension arms and related bearings.
2. Bent shock absorber rod.
1. Loose suspension system bolts.
2. Worn suspension arms and related bearings.
3. Worn swingarm and suspension bearings.
1. Weakened spring of shock absorber.
2. Leakage oil or gas of shock absorber.
3. Improperly set rear spring pre-load adjuster.
4. Improperly set damping force adjuster.
1. Bend shock absorber rod.
2. Bent swingarm.
3. Worn swingarm and rear suspension bearings.
4. Improperly set rear spring pre-load adjuster.
5. Improperly set damping force adjuster.
6. Improper chain adjustment.
1. Distorted rear wheel rims.
2. Damage or worn rear axle housing bearings.
3. Defective or incorrect rear tires.
4. Loose rear wheel hub nuts.
5. Distorted rear axle.
6. Loosen rear axle housing mounting bolts.
7. Improper rear brake adjustment.
8. Damaged or worn rear swingarm and related bearings.
9. Rear shock absorber leaks oil.
10. Loose rear swingarm nut.
C
O
P
Y
R
I
G
H
T
E
D
BRAKES
Poor braking
(FRONT and REAR)
1. Not enough brake fluid in the reservoir.
2. Air trapped in brake fluid circuit.
3. Pads worn down.
4. Too much play on brake lever or pedal.
5. Oil adhesion on friction surface of pads.
6. Worn disk.
Refill to level mark.
Bleed air out.
Replace.
Adjust.
Clean disk and pads.
Replace.
Insufficient brake
power.
1. Leakage of brake fluid from hydraulic system.
2. Worn pads.
3. Oil adhesion of engaging surface of pads.
4. Worn disk.
5. Air in hydraulic system.
Repair or replace.
Replace.
Clean disk and pads.
Replace.
Bleed air.
Brake squeaking.
1. Carbon adhesion on pad surface.
2. Tilted pad.
3. Damaged wheel bearing.
4. Loosen front-wheel axle or rear-wheel axle.
5. Worn pads.
6. Foreign material in brake fluid.
7. Clogged return port of master cylinder.
Repair surface with
sandpaper.
Modify pad fitting.
Replace.
Tighten to specified torque.
Replace.
Replace brake fluid.
Disassemble and clean
master cylinder.
Leakage of brake
fluid.
1. Insufficient tightening of connection joints.
2. Cracked hose.
3. Worn piston and/or cup.
Tighten to specified
torque.
Replace.
Replace piston and/or cup.
Excessive brake
lever stroke.
1. Air in hydraulic system.
2. Insufficient brake fluid.
3. Improper quality of brake fluid.
Bleed air.
Replenish fluid to specified
level ; bleed air.
Replace with correct fluid.
C
O
P
Y
R
I
G
H
T
E
D
09910-32812
Crankshaft installer
Used to install the crankshaft in the crankcase.
Special tools Part NumberPart NameDescription
09900-20101
Vernier Calipers
Used to conveniently measure various dimensions.
09900-20202
Micrometer (25~50mm)
Used for precise measurement (25~50mm measure ranges).
09900-20203
09900-20204
09900-20201
Micrometer (0~25mm)
09900-20508
Cylinder gauge set
Measure inside diameter of cylinder.
09900-20605
Dial calipers
Meassure width of conrod big-end.
09900-20606
Dial gauge
Meassure oscillation of wheel with using magnetic stand.
09900-20701
Magnetic stand
With using dial gauge.
09900-20806
Thickness gauge
Measure clearance of piston ring.
09900-21304
V-block
09900-21109
Torque wrench
With using magnetic stand.
Measure torque of tightening.
09900-25002
Pocket tester
Measure voltage, electric current, resistance.
SPECIAL TOOLS
09900-22401
Small bore gauge
Measure inside diameter of conrod small-end.
09900-26006
Engine tachometer
Measure rotational frequency of engine.
09910-20115
Conrod holder
Used to lock the crankshaft.
09900-25008
Multi circuit tester set
Inspect thermo-switch or temperature switch.
C
O
P
Y
R
I
G
H
T
E
D
09915-64511
Compression gauge
Measure cylinder compression.
09915-74511
Oil pressure gauge
Measure oil pressure of 4-stroke engine.
Separate to crankcase.
Used to install or remove clutch sleeve hub nut.
09920-13120
Crankcase separator
09920-53710
Clutch sleeve hub holder
Used with valve spring compressor.
09916-14520
Used with oil pressure gauge.
09915-74532
Oil pressure gauge adaptor
Used to remove and remounting valve stem.
09916-14510
Valve spring compressor
09921-20200
Bearing remover (10mm)
Used to remove bearing with the rotor remove sliding shaft.
09921-20210
09923-73210
09913-50121
Oil seal remover
09913-70122
Bearing installer
Used to remove the oil seal.
Used to drive bearing in.
09913-75820
Bearing installer
09913-76010
Bearing installer
09913-80112
Bearing installer
09910-36000
Cap plug wrench
Used to install or remove the magneto cover cap.
Special tools Part NumberPart NameDescription Special tools Part NumberPart NameDescription
09923-74510
Bearing remover (20~35mm)
Used to with bearing remover.
09930-30102
Rotor remove sliding shaft
C
O
P
Y
R
I
G
H
T
E
D
09930-30164
Rotor remover
Used to remove rotor.
C
O
P
Y
R
I
G
H
T
E
D
ENGINE
TIGHTENING TORQUE
Crankcase
Oil tank
ITEM kgfm Nm
Coolant drain bolt
Cooling fan mounting bolt
Cooling fan motor mounting bolt
Radiator mounting bolt
Magneto rotor nut
Magneto cover bolt
Exhaust pipe nut
Thermostat case bolt
Starter clutch bolt
Cylinder head bolt
Cylinder head cover bolt
Cylinder head base bolt
Cylinder base nut
Engine sprocket bolt
Engine oil check plug
Engine oil drain plug
Engine mounting nut
Engine mounting bolt
Spark plug
Cam chain tensioner mounting bolt
Cam chain tension adjuster mounting bolt
Cam chain tension adjuster bolt
Crankcase bolt
Clutch sleeve hub nut
Primary drive gear nut
Horn mounting bolt
Gearshift cam stopper
Gear position switch bolt
13
11 ~ 14
8 ~ 12
8
13
8 ~ 12
120
10
23
23
23
10
23 ~ 28
47
14
10
10
11 ~ 13
18
21
12
23
66
66
11
10
10
10
20
11
90
140
12
8 ~ 12
32
6.5
1.3
1.1 ~ 1.4
0.8 ~ 1.2
0.8
1.3
0.8 ~ 1.2
12.0
1.0
2.3
2.3
2.3
1.0
2.3 ~ 2.8
4.7
1.4
1.0
1.0
1.1 ~ 1.3
1.8
2.1
1.2
2.3
6.6
6.6
1.1
1.0
1.0
1.0
2.0
1.1
9.0
14.0
1.2
0.8 ~ 1.2
3.2
0.65
C
O
P
Y
R
I
G
H
T
E
D
Front & Rear shock absorber mounting nut (Upper)
Front & Rear shock absorber mounting bolt (Lower)
Swingarm pivot nut
Steering shaft nut
Steering shaft holder bolt
Front & Rear brake disk bolt
Front brake master cylinder mounting bolt
Rear brake master cylinder mounting bolt
Front & Rear brake caliper air bleeder valve
Front & Rear brake caliper mounting bolt
Front & Rear brake hose union bolt
Footrest mounting bolt
Front wheel hub nut
Rear wheel hub nut
Front & Rear wheel set nut
Front & Rear brake pad mounting pin
Knuckle end nut
Suspension arm pivot nut
Tie rod end nut
Tie rod lock nut
Throttle case bolt
Parking brake housing bolt
Rear cushion rod nut
Rear cushion lever nut
Rear sprocket mounting bolt
Rear axle shaft nut (inner & outer)
Handlebar clamp bolt
Parking brake adjuster lock nut
Rear brake caliper holder pin
Rear brake caliper pin bolt
4.0 ~ 6.0
4.0 ~ 6.0
7.0 ~ 10.0
4.0 ~ 6.0
5.0 ~ 8.0
4.9
1.8 ~ 2.8
1.8 ~ 2.8
0.5 ~ 0.8
0.8 ~ 1.2
0.9 ~ 1.4
1.8 ~ 2.8
4.0 ~ 6.0
4.0 ~ 6.0
5.5
10.0
3.92 ~ 5.88
1.8 ~ 2.8
4.3
4.0 ~ 6.0
2.2 ~ 3.5
2.9
0.5
2.8
1.0 ~ 2.0
7.0 ~ 10.0
7.0 ~ 10.0
1.8 ~ 2.8
12.0 ~ 15.0
1.8 ~ 2.8
1.8
1.8
2.3
40 ~ 60
40 ~ 60
70 ~ 100
40 ~ 60
50 ~ 80
49
18 ~ 28
18 ~ 28
5 ~ 8
8 ~ 12
9 ~ 14
18 ~ 28
40 ~ 60
40 ~ 60
55
100
39.2 ~ 58.8
18 ~ 28
43
40 ~ 60
22 ~ 35
29
5
28
10 ~ 20
70 ~ 100
70 ~ 100
18 ~ 28
120 ~ 150
18 ~ 28
18
18
23
CHASSIS
ITEM kgfm Nm
C
O
P
Y
R
I
G
H
T
E
D
SERVICE DATA
ITEM STANDARD LIMIT
36.0 (1.42)
29.0 (1.14)
0.1 ~ 0.2 (0.004 ~ 0.008)
0.2 ~ 0.3 (0.008 ~ 0.012)
0.010 ~ 0.037 (0.0004 ~ 0.0015)
0.030 ~ 0.057 (0.0012 ~ 0.0022)
5.000 ~ 5.012 (0.1969 ~ 0.1973)

4.975 ~ 4.990 (0.1959 ~ 0.1965)
4.955 ~ 4.970 (0.1951 ~ 0.1957)
45
6.5 ~ 7.1 kgf (14.3 ~ 15.7 lbs)

12.0 ~ 14.0 kgf (26.5 ~ 30.9 lbs)
1.25 ~ 1.65 (0.049 ~ 0.065)
IN.
EX.
IN.
EX.
IN.
EX.
IN. & EX.
IN. & EX.
IN.
EX.
IN. & EX.
IN. & EX.
IN. & EX.
IN. & EX.
Inner
Outer
Inner.
Outer
0.35 (0.014)
0.05 (0.002)
0.50 (0.02)
0.35 (0.014)
36.9 (1.45)
39.9 (1.57)
VALVE + GUIDE
Valve diam.
Valve clearance (When cold)
Valve guide to valve stem clearance
Valve stem deflection
Valve guide I.D.
Valve stem O.D.
Valve stem runout
Valve head thickness
Valve seat width
Valve seat angle
Valve head radial runout
Valve spring free length
Valve spring tension
Unit : mm (in)
C
O
P
Y
R
I
G
H
T
E
D
ITEM STANDARD LIMIT
16 kg/cm
2
(at 500 rpm)
0.050 ~ 0.060 (0.0020 ~ 0.0024)
96.000 ~ 96.015 (3.7795 ~ 3.7801)
95.945 ~ 95.960 (3.7774 ~ 3.7780)
(Measure at 18 mm (0.71 in) from the skirt end)
19.002 ~ 19.008 (0.7481 ~ 0.7484)
18.992 ~ 18.995 (0.7477 ~ 0.7478)
14 kg/cm
2
0.120 (0.0048)
96.075 (3.7825)
95.880 (3.7748)
0.05 (0.002)
0.5 (0.020)
0.7 (0.028)
0.150 (0.006)
0.150 (0.006)
19.030 (0.7492)
18.980 (0.7472)
Approx 11.0 (0.433)
Approx 10.0 (0.394)
0.25 ~ 0.40 (0.010 ~ 0.016)
0.40 ~ 0.55 (0.016 ~ 0.022)
1.21 ~ 1.23 (0.0476 ~ 0.0484)

1.01 ~ 1.03 (0.040 ~ 0.041)
2.01 ~ 2.03 (0.079 ~ 0.080)
1.170 ~ 1.190 (0.0461 ~ 0.0469)
0.970 ~ 0.990 (0.0382 ~ 0.0390)
1st
2nd
1st
2nd
1st
2nd
1st
2nd
Oil
1st
2nd
CYLINDER + PISTON + PISTON RING

Compression pressure
Piston to cylinder clearance
Cylinder bore
Piston diam.
Cylinder or cylinder head distortion
Piston ring free end gap
Piston ring end gap (Assembly condition)
Piston ring to groove clearance
Piston ring groove width
Piston ring thickness
Piston pin hole bore
Piston pin O.D.
Unit : mm (in)
C
O
P
Y
R
I
G
H
T
E
D
Oil pressure
Oil pump reduction ratio
1.0 ~ 3.0 kgf/cm
2
(at 60 , 3,000 rpm)
1.3 (45/34)
OIL PUMP
Clutch cable play
Drive plate thickness
Drive plate claw width
Driven plate distortion
Clutch spring free length
2.62 (0.103)
3.12 (0.123)
15.1 (0.595)
15.1 (0.595)
0.1 (0.004)
51.6 (2.032)
CLUTCH
10 ~ 15 (0.4 ~ 0.6)
2.92 ~ 3.08 (0.115 ~ 0.121)
3.42 ~ 3.58 (0.135 ~ 0.141)
15.9 ~ 16.0 (0.626 ~0.630)
15.9 ~ 16.0 (0.626 ~0.630)
54.2 (2.134)
Unit : mm (in)
NO. 1
NO. 2
NO. 1
NO. 2
ITEM STANDARD NOTE
ITEM STANDARD LIMIT
C
O
P
Y
R
I
G
H
T
E
D
Conrod small end I.D.
Conrod deflection
Conrod big end side clearance
Conrod big end width
Crank web to web width
Crankshaft runout
19.006 ~ 19.014 (0.7483 ~ 0.7486)
0.10 ~ 0.65 (0.004 ~ 0.026)

24.95 ~ 25.00 (0.982 ~ 0.984)
710.1 (2.7950.004)
19.040 (0.7496)
3.0 (0.12)
1.0 (0.040)
0.05 (0.002)
CONROD + CRANKSHAFT
Cam height
Camshaft O.D
Camshaft housing I.D.
Camshaft journal oil clearance
Camshaft runout
Cylinder head cover distortion
Cam chain pin (Arrow 3)
15th pin
39.98 ~ 40.02 (1.574 ~ 1.576)
39.98 ~ 40.02 (1.574 ~ 1.576)
21.959 ~ 21.980 (0.8645 ~ 0.8654)
22.012 ~ 22.025 (0.8666 ~ 0.8671)
IN.
EX.
IN. & EX.
IN. & EX.
IN. & EX.
39.88 (1.570)
39.88 (1.570)
0.15 (0.006)
0.10 (0.004)
0.05 (0.002)
CAMSHAFT + CYLINDER HEAD

Unit : mm (in)
Unit : mm (in)
ITEM STANDARD LIMIT
ITEM STANDARD LIMIT
C
O
P
Y
R
I
G
H
T
E
D
Primary reduction ratio
Secondary reduction ratio
Gear ratio
Shift fork to groove clearance
Shift fork groove width
Shift fork thickness
Drive chain
Drive chain slack
Reverse cable play
2.500 (75/30)
3.143 (44/14)
4.85 ~ 5.00 (0.191 ~ 0.197)
4.85 ~ 5.00 (0.191 ~ 0.197)
5.3 ~ 5.4 (0.209 ~ 0.213)
5.3 ~ 5.4 (0.209 ~ 0.213)
0.50 (0.020)
319.4 (12.58)
TRANSMISSION + DRIVE BELT

2.538 (33/13)
1.684 (32/19)
1.261 (29/23)
1.040 (26/25)
0.885 (23/26)
2.231(29/13)
RK 520EXW
102
317.5 (12.50)
1st
2nd
3rd
4th
5th
Reverse
Type
Links
20-pitch length
NO.1 & NO.2
NO.3
NO.1 & NO.2
NO.3
0.10 ~ 0.30 (0.004 ~ 0.012)
30 ~ 40 (1.2 ~ 1.6)
1 ~ 2 (0.04 ~ 0.08)
Unit : mm (in)
ITEM STANDARD LIMIT
C
O
P
Y
R
I
G
H
T
E
D
Carburetor type
Bore size
Idle r.p.m.
Float height
Main jet (M.J.)
Main air jet (M.A.J.)
Jet needle (J.N.)
Needle jet (N.J.)
Pilot jet (P.J.)
Throttle valve (TH.V.)
By-pass (B.P.)
Valve seat (V.S.)
Starter jet (G.S.)
Pilot screw (P.S.)
Pilot outlet (P.O.)
PV. Stroke (P. V.)
Throttle cable play
BDS42 TYPE
42
1,300~1,500 rpm
13 (0.51)
162.5
50
6DFY08-54-3
O-6M
45
105
1.5
42.5
STD
1.1
29.6
3 ~ 5 (0.12 ~ 0.20)
ITEM SPECIFICATION
CARBURETOR
#1
0.9
#2
0.8
#3
0.8
Unit : mm (in)
C
O
P
Y
R
I
G
H
T
E
D
Thermostat valve operating temperature
Thermostat valve lift
Water temperature switch operating temperature
Cooling fan thermo-switch operating temperature
Engine coolant type
Engine coolant capacity
Over 8 mm / 90 (Over 0.32 in/194)
THERMOSTAT + COOLING FAN + COOLANT
Valve opening
Valve closing
OFFON
ONOFF
OFFON
ONOFF
76 (169)
71 (160)
Approx. 120 (248)
Approx. 113 (235)
Approx. 95 (203)
Approx. 88(190)
1.4
Use an antifreeze/coolant compatible with

aluminum radiator, mixed with distilled
water only, at the ratio of 50 : 50
ITEM STANDARD LIMIT
C
O
P
Y
R
I
G
H
T
E
D
Battery
Type
Capacity
Standard elec-
trolyte S.G.
ELECTRICAL
Ignition timing
Spark plug
Spark performance
Fuse size
Magneto coil resistance
Magneto no-load voltage
Battery standard charging voltage
CR8E
0.7 ~ 0.8 (0.028 ~ 0.032)
CR7E
CR8E
CR9E
Over 8mm (0.32)
90 ~ 110
0.3 ~ 0.8
YTX9-BS
12V 8Ah
15A
Pick-up coil
Charging coil
G-L
Y-Y
Type
Gap
Hot type
Standard type
Cold type
BTDC 6/ 1,500rpm
Over 70V / 5,000 rpm
13.5 ~ 15.0V / 5,000 rpm
1.320 at 20(68)
Unit : mm (in)
ITEM STANDARD NOTE
C
O
P
Y
R
I
G
H
T
E
D
Head lamp
License plate lamp
Brake / Tail lamp
Turn signal lamp
Speedometer lamp
Neutral indicator lamp
Turn signal indicator lamp (Right & left)
High beam indicator lamp
Coolant temperature indicator lamp
Fuel indicator lamp
Reverse indicator lamp
5W
LED type
10W 4
LCD type
3.4W
3.4W
3.4W
3.4W
3.4W
3.4W
55W
55W
5W
ITEM SPECIFICATION
HI
LO
POSITION
WATTAGE
CAUTION
Do not use except the specified bulb (Wattage).
LED : Light Emitting Diode
LCD : Liquid Crystal Display
Unit : W
C
O
P
Y
R
I
G
H
T
E
D
Swingarm pivot shaft runout
Maximum (Softest)
Standard
Minimum(Stiffest)
Maximum (Softest)
Standard
Minimum(Stiffest)
280 (11.0)
270 (10.6)
258 (10.2)
235 (9.25)
228 (8.98)
213 (8.39)
0.6 (0.024)
SUSPENSION
Unit : mm (in)
ITEM STANDARD LIMIT
STANDARD FRONT SHOCK ABSORBER DAMPING FORCE
Compression Tension
Softer
Standard
Stiffer
End of S direction (counter-clockwise)
STANDARD REAR SHOCK ABSORBER DAMPING FORCE
Compression Tension
Softer
Standard
Stiffer
Front suspension spring set
length
Rear suspension spring set
length
C
O
P
Y
R
I
G
H
T
E
D
Rear brake pedal height
Brake disk thickness
Brake disk runout
Master cylinder bore
Master cylinder piston diam.
Brake caliper cylinder bore
Brake caliper piston diam.
Brake fluid type
Rear axle shaft nunout
Tire size
Wheel rim size
Tire tread depth
Toe-in [ When apply to a load 75 kg (165 lbs) ]
Caster
Camber
4.0 (0.16)
4.3 (0.17)
15.870 ~ 15.913 (0.6248 ~ 0.6265)

12.700 ~ 12.743 (0.5000 ~ 0.5017)
15.827 ~ 15.854 (0.6227 ~ 0.6242)
12.657 ~ 12.684 (0.4983 ~ 0.4994)
32 (1.26)
32 (1.26)
DOT4
DOT4
217-10
2011-9
105.5
98
355 (14.0) [when one person riding from the ground]

0 ~ 5 mm (0 ~ 0.2 in)
7.3
0
3.0 (0.12)
3.0 (0.12)
0.3 (0.012)
6 (0.24)
4 (0.16)
4 (0.16)
Front
Rear
FrontRear
Front
Rear
Front
Rear
FrontRear
FrontRear
Front
Rear
Front
Rear
Front
Rear
Front
Rear
BRAKE + WHEEL
Unit : mm (in)
ITEM STANDARD LIMIT
C
O
P
Y
R
I
G
H
T
E
D
Fuel type
Fuel tank capacity
Engine oil type
Engine oil capacity [Total : 2,700 ]
8
Gasoline used should be graded 91 octane or higher.
An unleaded gasoline is recommened.
API Over SL (SAE 10W/40)
2,500
2,600
2,700
1,900
100
550
150
FUEL + OIL
Change
Filter change
Overhaul
Oil tand side
Filter side
Engine side
Oil hose side
TIRE PRESSURE
COLD INFLATION TIRE PRESSURE
FRONT
ONE PERSON TWO PERSONS
0.3 kgf/cm
2
30 kPa
4.4 psi
0.35 kgf/cm
2
35 kPa
4.9 psi
0.35 kgf/cm
2
35 kPa
4.9 psi
0.3 kgf/cm
2
30 kPa
4.4 psi
REAR
ITEM STANDARD NOTE
C
O
P
Y
R
I
G
H
T
E
D
WIRE AND CABLE ROUTING
C
O
P
Y
R
I
G
H
T
E
D
C
O
P
Y
R
I
G
H
T
E
D
C
O
P
Y
R
I
G
H
T
E
D
C
O
P
Y
R
I
G
H
T
E
D
C
O
P
Y
R
I
G
H
T
E
D
C
O
P
Y
R
I
G
H
T
E
D
WIRING DIAGRAM
W
I
R
E

C
O
L
O
R
B

:

B
l
a
c
k
L
g

:

L
i
g
h
t

g
r
e
e
n
Y

:

Y
e
l
l
o
w
B
r

:

B
r
o
w
n
O

:

O
r
a
n
g
e
G

:

G
r
e
e
n
R

:

R
e
d
B
W
:

B
l
a
c
k

w
i
t
h

W
h
i
t
e

t
r
a
c
e
r
W
B
:

W
h
i
t
e

w
i
t
h

B
l
a
c
k

t
r
a
c
e
r
G
r

:

G
r
a
y
S
b

:

L
i
g
h
t

b
l
u
e
L

:

B
l
u
e
W

:

W
h
i
t
e
Y
B

:

Y
e
l
l
o
w

w
i
t
h

B
l
a
c
k

t
r
a
c
e
r
B
L

:

B
l
a
c
k

w
i
t
h

B
l
u
e

t
r
a
c
e
r
W
L

:

W
h
i
t
e

w
i
t
h

B
l
u
e

t
r
a
c
e
r
Y
W

:

Y
e
l
l
o
w

w
i
t
h

W
h
i
t
e

t
r
a
c
e
r
G
R

:

G
r
e
e
n

w
i
t
h

R
e
d

t
r
a
c
e
r
G
L
:

G
r
e
e
n

w
i
t
h

B
l
u
e

t
r
a
c
e
r
W
L

:

W
h
i
t
e

w
i
t
h

B
l
u
e

t
r
a
c
e
r
Y
R
:

Y
e
l
l
o
w

w
i
t
h

R
e
d

t
r
a
c
e
r
C
O
P
Y
R
I
G
H
T
E
D
S
H
I
M

N
o
.
H
O
W

T
O

U
S
E

T
H
E

C
H
A
R
T
1
.

M
e
a
s
u
r
e

t
h
e

t
a
p
p
e
t

c
l
e
a
r
a
n
c
e
.
(
W
h
e
n

c
o
l
d
)
2
.

M
e
a
s
u
r
e

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

a
t

p
r
e
s
e
n
t
.
3
.

L
o
o
k

f
o
r

m
e
e
t
i
n
g

s
p
a
c
e

i
n

t
h
a
t

h
o
r
i
z
o
n
t
a
l

l
i
n
e

f
o
r

t
h
i
c
k
n
e
s
s

a
n
d

v
e
r
t
i
c
a
l

l
i
n
e

f
o
r

c
l
e
a
r
a
n
c
e
.
(
E
X
A
M
P
L
E
)
W
h
e
n

t
h
e

t
a
p
p
e
t

c
l
e
a
r
a
n
c
e

i
s

0
.
3
8
m
m

a
n
d

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

a
t

p
r
e
s
e
n
t

i
s

2
.
7
0
m
m
,

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

s
h
o
u
l
d

b
e

u
s
e
d

2
.
9
5
m
m
.
T
A
P
P
E
T

S
H
I
M

S
E
L
E
C
T
I
O
N

C
H
A
R
T

(
I
N
.
)
S
p
e
c
i
f
i
e
d

c
l
e
a
r
a
n
c
e

-

A
d
j
u
s
t
m
e
n
t

u
n
n
e
c
e
s
s
a
r
y
0
.
0
0

~

0
.
0
4
0
.
0
5

~

0
.
0
9
0
.
1
0

~

0
.
2
0
0
.
2
1

~

0
.
2
5
0
.
2
6

~

0
.
3
0
0
.
3
1

~

0
.
3
5
0
.
3
6

~

0
.
4
0
0
.
4
1

~

0
.
4
5
0
.
4
6

~

0
.
5
0
0
.
5
1

~

0
.
5
5
0
.
5
6

~

0
.
6
0
0
.
6
1

~

0
.
6
5
0
.
6
6

~

0
.
7
0
0
.
7
1

~

0
.
7
5
0
.
7
6

~

0
.
8
0
0
.
8
1

~

0
.
8
5
0
.
8
6

~

0
.
9
0
0
.
9
1

~

0
.
9
5
0
.
9
6

~

1
.
0
0
1
.
0
1

~

1
.
0
5
1
.
0
6

~

1
.
1
0
1
.
1
1

~

1
.
1
5
3
.
4
0
3
.
4
5
S
H
I
M

T
H
I
C
K
N
E
S
S
A
T

P
R
E
S
E
N
T
(
m
m
)
M
E
A
S
U
R
I
N
G

T
A
P
P
E
T

C
L
E
A
R
A
N
C
E

(
m
m
)
3
.
5
0
3
5
0
3
.
3
5
3
.
4
0
3
.
4
5
3
4
5
3
.
3
0
3
.
3
5
3
.
4
0
3
4
0
3
.
2
5
3
.
3
0
3
.
3
5
3
3
5
3
.
2
0
3
.
2
5
3
.
4
0
3
.
4
5
3
.
5
0
3
.
4
5
3
.
5
0
3
.
5
0
3
.
3
0
3
3
0
3
.
1
5
3
.
2
0
3
.
3
5
3
.
4
0
3
.
4
5
3
.
2
5
3
2
5
3
.
1
0
3
.
1
5
3
.
3
0
3
.
3
5
3
.
4
0
3
.
2
0
3
2
0
3
.
0
5
3
.
1
0
3
.
2
5
3
.
3
0
3
.
3
5
3
.
5
0
3
.
4
5
3
.
4
0
3
.
5
0
3
.
4
5
3
.
5
0
3
.
1
5
3
1
5
2
3
0
2
3
5
2
4
0
2
4
5
2
5
0
2
5
5
2
6
0
2
6
5
2
7
0
2
7
5
2
8
0
2
8
5
2
9
0
2
9
5
3
0
0
3
0
5
3
1
0
2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0
2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5
2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5
2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0
2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5
2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0
2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

C
O
P
Y
R
I
G
H
T
E
D
S
H
I
M

N
o
.
H
O
W

T
O

U
S
E

T
H
E

C
H
A
R
T
1
.

M
e
a
s
u
r
e

t
h
e

t
a
p
p
e
t

c
l
e
a
r
a
n
c
e
.
(
W
h
e
n

c
o
l
d
)
2
.

M
e
a
s
u
r
e

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

a
t

p
r
e
s
e
n
t
.
3
.

L
o
o
k

f
o
r

m
e
e
t
i
n
g

s
p
a
c
e

i
n

t
h
a
t

h
o
r
i
z
o
n
t
a
l

l
i
n
e

f
o
r

t
h
i
c
k
n
e
s
s

a
n
d

v
e
r
t
i
c
a
l

l
i
n
e

f
o
r

c
l
e
a
r
a
n
c
e
.
(
E
X
A
M
P
L
E
)
W
h
e
n

t
h
e

t
a
p
p
e
t

c
l
e
a
r
a
n
c
e

i
s

0
.
4
8
m
m

a
n
d

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

a
t

p
r
e
s
e
n
t

i
s

2
.
7
0
m
m
,

t
h
e

s
h
i
m

t
h
i
c
k
n
e
s
s

s
h
o
u
l
d

b
e

u
s
e
d

2
.
9
5
m
m
.
T
A
P
P
E
T

S
H
I
M

S
E
L
E
C
T
I
O
N

C
H
A
R
T

(
E
X
.
)
S
p
e
c
i
f
i
e
d

c
l
e
a
r
a
n
c
e
0
.
1
0

~

0
.
1
4

0
.
1
5

~

0
.
1
9

0
.
2
0

~

0
.
3
0

0
.
3
1

~

0
.
3
5

0
.
3
6

~

0
.
4
0

0
.
4
1

~

0
.
4
5

0
.
4
6

~

0
.
5
0

0
.
5
1

~

0
.
5
5

0
.
5
6

~

0
.
6
0

0
.
6
1

~

0
.
6
5

0
.
6
6

~

0
.
7
0

0
.
7
1

~

0
.
7
5

0
.
7
6

~

0
.
8
0

0
.
8
1

~

0
.
8
5

0
.
8
6

~

0
.
9
0

0
.
9
1

~

0
.
9
5

0
.
9
6

~

1
.
0
0

1
.
0
1

~

1
.
0
5

1
.
0
6

~

1
.
1
0

1
.
1
1

~

1
.
1
5

1
.
1
6

~

1
.
2
0

1
.
2
1

~

1
.
2
5
3
.
4
0
3
.
4
5
S
H
I
M

T
H
I
C
K
N
E
S
S
A
T

P
R
E
S
E
N
T
(
m
m
)
M
E
A
S
U
R
I
N
G

T
A
P
P
E
T

C
L
E
A
R
A
N
C
E

(
m
m
)
3
.
5
0
3
5
0
3
.
3
5
3
.
4
0
3
.
4
5
3
4
5
3
.
3
0
3
.
3
5
3
.
4
0
3
4
0
3
.
2
5
3
.
3
0
3
.
3
5
3
3
5
3
.
2
0
3
.
2
5
3
.
4
0
3
.
4
5
3
.
5
0
3
.
4
5
3
.
5
0
3
.
5
0
3
.
3
0
3
3
0
3
.
1
5
3
.
2
0
3
.
3
5
3
.
4
0
3
.
4
5
3
.
2
5
3
2
5
3
.
1
0
3
.
1
5
3
.
3
0
3
.
3
5
3
.
4
0
3
.
2
0
3
2
0
3
.
0
5
3
.
1
0
3
.
2
5
3
.
3
0
3
.
3
5
3
.
5
0
3
.
4
5
3
.
4
0
3
.
5
0
3
.
4
5
3
.
5
0
3
.
1
5
3
1
5
2
3
0
2
3
5
2
4
0
2
4
5
2
5
0
2
5
5
2
6
0
2
6
5
2
7
0
2
7
5
2
8
0
2
8
5
2
9
0
2
9
5
3
0
0
3
0
5
3
1
0
2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0
2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

2
.
3
0

2
.
3
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

2
.
4
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

2
.
4
5

2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5
2
.
5
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

2
.
5
5

2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5
2
.
6
0

2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0
2
.
6
5

2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5
2
.
7
0

2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0
2
.
7
5

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
8
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
8
5

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
9
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

2
.
9
5

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
0
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
0
5

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
1
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
1
5

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
2
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
2
5

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

3
.
3
0

3
.
3
5

3
.
4
0

3
.
4
5

3
.
5
0

C
O
P
Y
R
I
G
H
T
E
D
Prepared by
1st Ed. MAR. 2007.
Manual No. 99000HP8910
Printed in Korea
C
O
P
Y
R
I
G
H
T
E
D

TE450S Service Manual

Uploaded by

Copyright:

Available Formats

TE450S Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TE450S Service Manual

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

Replace every 4 years

CAM CHAIN TENSION ADJUSTER

CAM CHAIN TENSIONER

Remove the oil seal .

GEAR POSITION SWITCH

PRIMARY DRIVE GEAR AND

Gearshift cam stopper

Install the gearshift shaft .

Install the dowel pins and new gasket .

), this mixing ratio should be increased

) setting the cooling fan in motion.

Multi circuit tester set : 09900-25008

Multi circuit tester set : 09900-25008

Water temperature switch

(Over 0.32 in at 194

Thermostat case bolt

Y-Y 0.3 ~ 0.8

Stator coil resistance

Pocket tester : 09900-25002

STARTER MOTOR I NSPEC-

LIGHT & DIMMER SWITCH

TURN SIGNAL SWITCH

GEAR POSITION SWITCH

Rear shock absorber

5.000 ~ 5.012 (0.1969 ~ 0.1973)

6.5 ~ 7.1 kgf (14.3 ~ 15.7 lbs)

1.21 ~ 1.23 (0.0476 ~ 0.0484)

CYLINDER + PISTON + PISTON RING

0.10 ~ 0.65 (0.004 ~ 0.026)

CAMSHAFT + CYLINDER HEAD

TRANSMISSION + DRIVE BELT

Use an antifreeze/coolant compatible with

15.870 ~ 15.913 (0.6248 ~ 0.6265)

355 (14.0) [when one person riding from the ground]

You might also like