2005 Pearson Education South Asia Pte LTD
2005 Pearson Education South Asia Pte LTD
1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and Bernoullis Equation 7. General Energy Equation 8. Reynolds Number, Laminar Flow, Turbulent Flow and Energy Losses Due to Friction
2005 Pearson Education South Asia Pte Ltd
9. Velocity Profiles for Circular Sections and Flow in Noncircular Sections 10.Minor Losses 11.Series Pipeline Systems 12.Parallel Pipeline Systems 13.Pump Selection and Application 14.Open-Channel Flow 15.Flow Measurement 16.Forces Due to Fluids in Motion
2005 Pearson Education South Asia Pte Ltd
17.Drag and Lift 18.Fans, Blowers, Compressors and the Flow of Gases 19.Flow of Air in Ducts
Chapter Objectives
Use Newtons second law of motion, F = ma, to develop the force equation, which is used to compute the force exerted by a fluid as its direction of motion or its velocity is changed. Relate the force equation to impulsemomentum. Use the force equation to compute the force exerted on a stationary object that causes the change in direction of a fluid flow stream. Use the force equation to compute the force exerted on bends in pipelines. Use the force equation to compute the force on moving objects, such as the vanesof a pump impeller.
Chapter Outline
1. 2. 3. 4.
Introductory Concepts Force Equation Impulse-Momentum Equation Problem-Solving Method Using the Force Equations 5. Forces on Stationary Objects 6. Forces on Bends in Pipelines 7. Forces on Moving Objects
Whenever a fluid stream is deflected from its initial direction or if its velocity is changed, a force is required to accomplish the change. Sometimes the force is desired, sometimes it is destructive.
Whenever the magnitude or direction of the velocity of a body is changed, a force is required to accomplish the change. Newtons second law of motion is often used to express this concept in mathematical form; the most common form is
Force equals mass times acceleration. Acceleration is the time rate of change of velocity.
2005 Pearson Education South Asia Pte Ltd
In fluid flow problems, a continuous flow is caused to undergo the acceleration, and a different form of Newtons equation is desirable. Because acceleration is the time rate of change of velocity, Eq. (161) can be written as
The term m/t can be interpreted as the mass flow rate, that is, the amount of mass flowing in a given amount of time.
2005 Pearson Education South Asia Pte Ltd
This is the general form of the force equation for use in fluid flow problems because it involves the velocity and volume flow rate, items generally known in a fluid flow system.
2005 Pearson Education South Asia Pte Ltd
The force equation, Eq. (164), is related to another principle of fluid dynamics, the impulsemomentum equation. Impulse is defined as a force acting on a body for a period of time, and it is indicated by
Momentum is defined as the product of the mass of a body and its velocity. The change in momentum is
In an instantaneous sense,
Here we have shown the impulsemomentum equation for steady flow conditions. In an instantaneous sense,
In general, if three perpendicular directions are called x, y, and z, a separate equation can be written for each direction:
In a particular direction, say x, the term Fx refers to the net external force that acts on the fluid in that direction.
Below is the procedure for using the force equations: 1. Identify a portion of the fluid stream to be considered a free body. This will be the part where the fluid is changing direction or where the geometry of the flow stream is changing. 2. Establish reference axes for directions of forces. Usually one axis is chosen to be parallel to one part of the flow stream. In the example problems to follow, the positive x and y directions are chosen to be in the same direction as the reaction forces.
3. Identify and show on the free-body diagram all external forces acting on the fluid. All solid surfaces that affect the direction of the flow stream exert forces. Also, the fluid pressure acting on the crosssectional area of the stream exerts a force in a direction parallel to the stream at the boundary of the free body. 4. Show the direction of the velocity of flow as it enters the free body and as it leaves the free body.
5. Using the data thus shown for the free body, write the force equations in the pertinent directions. Use Eq. (165), (166), or (167). 6. Substitute data and solve for the desired quantity.
When free streams of fluid are deflected by stationary objects, external forces must be exerted to maintain the object in equilibrium.
Example 16.1
A 25-mm-diameter jet of water having a velocity of 6 m/s is deflected 90 by a curved vane, as shown in Fig. 16.1. The jet flows freely in the atmosphere in a horizontal plane. Calculate the x and y forces exerted on the water by the vane.
Example 16.1
Using the force diagram of Fig. 16.2, we can write the force equation for the x direction
Example 16.1
Example 16.2
In a decorative fountain, 0.05 m3/s of water having a velocity of 8 m/s is being deflected by the angled chute shown in Fig. 16.3. Determine the reactions on the chute in the x and y directions shown. Also calculate the total resultant force and the direction in which it acts. Neglect elevation changes. Figure 16.4 shows the x and y components of the velocity vectors and the assumed directions for Rx and Ry. The force equation in the x direction is
Example 16.2
Example 16.2
We know that
Neglecting friction in the chute, we can assume that v1 = v2. The only external force is Rx. Then we have
Example 16.2
We know that
Example 16.2
Example 16.2
Then we have
Example 16.2
Therefore, the resultant force that the chute must exert on the water is 693 N acting 75 from the horizontal, as shown in Fig. 16.4.
Figure 16.5 shows a typical 90 elbow in a pipe carrying a steady volume flow rate Q. To ensure proper installation, it is important to know how much force is required to hold it in equilibrium.
Example 16.3
Calculate the force that must be exerted on the pipe shown in Fig. 16.5 to hold it in equilibrium. The elbow is in a horizontal plane and is connected to two 4-in Schedule 40 pipes carrying 3000 L/min of water at 15C. The inlet pressure is 550 kPa.
Example 16.3
The problem may be visualized by considering the fluid within the elbow to be a free body, as shown in Fig. 16.6. Forces are shown in black vectors, and the direction of the velocity of flow is shown by blue vectors. A convention must be set for the directions of all vectors. Here we assume that the positive x direction is to the left and the positive y direction is up. The forces Rx and Ry are the external reactions required to maintain equilibrium. The forces p1A1 and p2A2 are the forces due to the fluid pressure. The two directions will be analyzed separately.
2005 Pearson Education South Asia Pte Ltd
Example 16.3
Example 16.3
We find the net external force in the x direction by using the equation
We know that
Then we have
Example 16.3
Example 16.3
We know that
Example 16.3
Then we have
If energy losses in the elbow are neglected, v2 = v1 and p2 = p1 because the sizes of the inlet and outlet are equal. Then,
Example 16.3
The forces Rx and Ry are the reactions caused at the elbow as the fluid turns 90. They may be supplied by anchors on the elbow or taken up through the flanges into the main pipes.
Example 16.4
Linseed oil with a specific gravity of 0.93 enters the reducing bend shown in Fig. 16.7 with a velocity of 3 m/s and a pressure of 275 kPa. The bend is in a horizontal plane. Calculate the x and y forces required to hold the bend in place. Neglect energy losses in the bend.
Example 16.4
The fluid in the bend is shown as a free body in Fig. 16.8. We must first develop the force equations for the x and y directions shown. The force equation for the x direction is
Algebraic signs must be carefully included according to the sign convention shown in Fig. 16.8. Notice that all forces and velocity terms are the components in the x direction.
2005 Pearson Education South Asia Pte Ltd
Example 16.4
Example 16.4
Example 16.4
Because of continuity,
Example 16.4
The vanes of turbines and other rotating machinery are familiar examples of moving objects that are acted on by high-velocity fluids. A jet of fluid with a velocity greater than that of the blades of the turbine exerts a force on the blades, causing them to accelerate or to generate useful mechanical energy. When dealing with forces on moving bodies, the relative motion of the fluid with respect to the body must be considered.
Example 16.5
Figure 16.9(a) shows a jet of water with a velocity v1 striking a vane that is moving with a velocity v0. Determine the forces exerted by the vane on the water if v1 = 20 m/s and v0 = 8 m/s. The jet is 50 mm in diameter.
Example 16.5
The system with a moving vane can be converted into an equivalent stationary system as shown in Fig. 16.9(b) by defining an effective velocity ve and an effective volume flow rate Qe. We then have
where A1 is the area of the jet as it enters the vane. It is only the difference between the jet velocity and the vane velocity that is effective in creating a force on the vane.
Example 16.5
The force equations can be written in terms of ve and Qe. In the x direction,
In the y direction,
We know that
Example 16.5
Then the reactions are calculated from Eqs. (1613) and (1614):