Piaggio Tech Manuals
Piaggio Tech Manuals
Piaggio Tech Manuals
Electrical systems
Electrical Systems
Electrical Systems
Electrical Systems
Two Stroke
Manual Engines
Electrical Systems
General
Fuel Systems
Mechanical Systems
ON
Ignition Switch
15 amp
Red / Blue
Fuse's in
Orange
Battery
Compartment
Blue
Red
White
B
Black
E
Yellow
S
Black / Blue
L Oil Tank Low Oil
Sender Warning
Light
White
White / Red
Yellow Yellow
Black / Blue
Turn
Indicator
Switch
Right Turn Indicators
Left Turn Indicators
* The low oil warning light check function is controlled by the indicator relay.
* The oil check light should come on for 15 seconds when the ignition is first turned on.
* If the system fails: first check the 7.5 amp fuse located under the front grill (horn) panel.
1 - 10
DIESIS 100 Charging / Ignition
Piaggio Ltd. 11/06/02 Derbi engine
Yellow / Green
Yellow / Green Indicators NGK
RIGHT B9 ES
OFF
LEFT
Yellow
Yellow / White
AC Supply Black / Red
Yellow
Red + 5o C Green / Black
Yellow / Green
Thermostat
Ignition Switch
Green / Black
DC Supply Black Carb. Heater LOCK
Black OFF
ON
Red
Red / Blue Green
4 Red Orange
To amp Yellow / Green Black Red / White
starter
solenoid
+ BATTERY
Orange - Indicator switch Red / Blue - DC supply
Rectifier
Earth wires are - Yellow / green. Indicator
Regulator &
Relay
Yellow wire is AC supply. Regulator
Red / Blue wire is DC supply.
Engine earth is very important.
Carb heater is driven by AC power via a thermostat.
No separate Ignition pick up, CDI is triggered by the AC wave.
Ignition is earthed to stop the engine.
TESTS.
Stator: Yellow - Earth = min 25 v AC. White / Red - Earth = min 30 v AC. Engine at mid rpm.
Yellow - Earth = 0.9 ohm + 0.2. White / Red - Earth = 1.1ohm + 0.2. Stator un-plugged.
Black / Red - Earth = 238 ohm + 10%. Stator un-plugged.
Regulator: Yellow - Earth = 13.5 + 0.5 v AC. White / Red - Earth = 13.5 + 1.0 v DC. Engine at mid rpm.
Ignition: HT coil secondary resistance = 5 - 6 K ohm. Unit un-plugged.
8
FUSE EXPLANATION
Runner FX 125 & FXR 180
Notes.
• Ignition circuit is completely separate and self powered. It does not have any fuses.
• The cooling fan is permanently live and is protected by the main 25 amp fuse.
• The starter motor supply is not fused.
3
Lighting
Switch
7
125 / 180 2T Ignition
Hexagon LX / LXT
IGNITION SWITCH
ON
OFF
GREEN BLACK
GREEN
STAT OR
WHITE
BROWN
RED PURPLE
R B W G V
IGNITION TIMING IS CDI CONTROLLED
Not adjustable
CDI UNIT
Skipper and Typhoon:
Meter between > Red - Brown White - Green Purple - Earth HT lead - Earth
Skipper / Typhoon 125 90 - 140 ohm 100 - 160 ohm 0.5 + ohm
0.025 + k ohm
4.8 0.25
NOTES.
* The ignition circuit is a separate self-contained circuit with no fuses and no connection to the other
electrical circuits on the vehicle. It has a separate charging coil in the stator (Green & White wires).
* The ignition switch contacts are OPEN when the engine is RUNNING. Contacts are CLOSED when
switch is turned OFF, this allows the system to discharge to earth. When fault finding, if there is no spark
then check the "green" and "purple" wires to see if there is a "leak" to earth. Unplug stator & CDI, check
* A "Resistor" type spark plug and a resistor plug cap should always be fitted.
* This circuit does not require the engine to chassis earth. But if that earth lead is missing it is possible that
trying to use the starter motor could force excess current through the CDI and damage it.
6
125 / 180 Two Stroke INDICATOR CIRCUIT
Piaggio Ltd 06/08/2002 Piaggio Ltd
BLACK
STARTER STARTER
RELAY SWITCH
INDICATOR
RELAY
BE
L B
+ 12V DC OIL WARNING
LAMP
S
STOP SWITCH
BLUE / RED
YELLOW
BLACK / BLUE
INDICATOR SWITCH
ABOVE. Vehicles 1999> Cirduit with oil check light that comes on when ignition is switched on.
Refer to the Service Station Manual. Also Technical Notes 2/99 and 3/99.
BELOW. Vehicles <1999 Circuit with oil check light that comes on when brake is held on and starter
button is pressed.
WHITE / RED
INDICATOR
RELAY
STARTER
LOW OIL RELAY
WARNING
OIL WARNING SWITCH
LAMP
DIODE
INDICATOR SWITCH
BLACK / BLUE
5
125 & 180cc 2t charging / Ignition
Typhoon, Skipper, Hexagon, Runner
WHITE YELLOW
BROWN
RED IGNITION
PICK UP
GREEN
STATOR
RED
BATTERY +
YELLOW
12v
FUSE
RED
IGNITION SWITCH
ON
OFF
COOLING FAN
ON
WATER COOLED
PURPLE GREEN RED MODELS
WHITE
SUPPLY
CDI TO
Unit SYSTEMS
NOTES
* Choke and Carb' heater will have a supply with ignition turned on but the
rectifier / regulator will only complete the circuit to earth when it detects a CHARGE
charge. I.e. the engine is running. WARNING
* The Charge warning light goes out when the engine is charging because +12v LIGHT
D.C. is applied to both sides of the bulb, not because the circuit is broken.
* On water cooled engines the cooling fan is always live, the thermostat switch is
on the earth side. So a battery going flat could be caused by a faulty fan or fan
switch.
* The starter solenoid is always live so is a possible cause of a battery going flat
YELLOW
YELLOW
BROWN
WHITE
TESTS
GREY
RED
1. Stator Output.
Yellow to Yellow 27 - 31 v A.C.@ 2000 rpm. Unplug regulator.
Green - White 50 -150 ohm. Runner & Hexagon.(Stator un-plugged) A L C B G G
100 -160 ohm. Skipper & Typhoon.(Stator un-plugged)
Red - Brown 90 -140 ohm. All models. (Stator un-plugged)
2. Charging.
Between Red & Battery positive: >< 8.5 amps@ 2000 rpm with a fully
charged battery (13.5v) Choke
3. Battery voltage must be present at terminal "C" with ignition on or the output Control
from terminal B will be unregulated. Battery will boil, bulbs will blow etc. DC
MAIN FUSE: Rectifier
Runner (ZAPM07 / 08) 25 amp. Regulator
Out put only when
Hexagon (EXS1T & ZAPM05 / 06) 25 amp. charging
Typhoon (ZAPM02) 15 amp.
Skipper (CSM1T) 7.5 amp.
4
50cc 2t Ignition
Piaggio Ltd 19/07/02 Piaggio Ltd
This circuit could apply to any 50cc two stroke with or without a rev counter
IGNITION SWITCH
ON REV COUNTER
OFF
GREEN
COMMON EARTH
Champion NR2C FOR
NGK BR9ES INSTRUMENT PANNEL
GREEN
STATOR
GREEN
GREEN Ignition
Charging Coil
WHITE
WHITE
RED
RED
IGNITION PICK UP
TESTS
CDI / COIL 1. UNPLUG STATOR and CDI. GREEN WIRE SHOULD BE
CDI / COIL EARTHED WHEN IGNITION IS "OFF"
unit 2. CHECK CHARGING COIL.
unit GREEN TO WHITE = 980 ± 50 ohms.
3. CHECK TRIGGER COIL.
RED TO WHITE = 88 ± 5 ohms.
4. SPARK PLUG
NRG's are now supplied with Champion N1C plugs
The NGK equlivilent is B10ES.
This plug is very cold running and may not suit all riders.
If you find that a machine is fouling plugs try fitting an
NGK B9ES.
NOTES
3
NRG & ZIP Cat. Charging & Guages
Piaggio Ltd. 02/05/2003 8 pin regulator
YELLOW
2 3
7.5 amp
FUSE
BLUE
RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
FUEL GUAGE
OIL TANK
SENDER
FUEL
BROWN
BROWN
1
FUEL OIL
WARNING WARNING
LIGHT LIGHT
DC SERVICES
WHITE / VIOLET
WHITE / VIOLET
BLUE / RED
Brake light
Horn
WHITE / GREEN
WHITE
YELLOW / GREEN
FUEL
SENDER 5
UNIT
5 TO INDICATOR
SWITCH
4
AC
YELLOW / GREEN
SERVICES
WHITE / VIOLET
GREY / BLUE
Head light
BLUE / RED
Instruments
BLUE / BLACK
TESTS
1. Grey / Blue to earth = 25-30v AC YELLOW
stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC
1 2 3 4 5 6 7 8
stator and battery disconnected and engine at
2000 rpm.
3. Ammeter between red wire and battery positive
= 1.5-2 amp with fully charged battery and TIMER
1-2a
50 / 80cc 2T charging
Piaggio Ltd. 06/08/2002 8 pin regulator
YELLOW
2 7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION
SWITCH + BATTERY
WHITE 12v
BLUE
1
OIL
WARNING OIL TANK
LIGHT SENDER
DC SERVICES
Brake light
GREY / BLUE Horn
AC
SERVICES
Head light
GREY / BLUE
Tail light 4
WHITE
BLACK
Instruments
TO INDICATOR
BLUE / BLACK SWITCH
CHOKE UNIT GREY
NOT YELLOW
USED
1 2 3 4 5 6 7 8
OIL
LIGHT
TIMER
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the later 50cc and 80cc two stroke wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on for 15 seconds when ignition is turned on.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay and oil light check function.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter motor
but not the DC circuit or ignition circuit.
2
50 / 80cc 2T charging
Piaggio Ltd. 02/05/2003 5 pin regulator
BLUE BLUE 3
7.5 amp
RED FUSE
RED
ON
+ BATTERY
IGNITION
SWITCH OFF 12v
RED 12v 4ah - 50cc
12v 5ah - 80cc
WHITE
1
YELLOW
DC SERVICES
Brake light
Horn
GREY / BLUE
AC
SERVICES
Head light
Tail light
GREY / BLUE
Instruments
YELLOW
GREY
WHITE
BLACK
CHOKE UNIT GREY
A A G B+
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the early 50cc and 80cc two stroke wiring using a five pin connector on the rectifier /
regulator. Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on when the starter button is pressed.
* Two completely separate circuits for AC & DC.
AC is full wave and regulated
DC is half wave rectified and regulated
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
NOTES.
Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter motor
but not the DC circuit or ignition circuit.
1-1
PUREJET 50 IGNITION / CHARGE
Piaggio Ltd. 02/09/2003 GILERA RUNNER
BROWN
RED OFF
15 amp Champion
STATOR RG6YCA
RED
FUSE
BLUE
YELLOW 15 amp
YELLOW
YELLOW HT COIL
To starter
relay
BLUE
BATTERY +
BLACK / VIOLET
12v
BLUE
BLUE
BLACK / VIOLET
ORANGE
BROWN
BLUE
BLUE
RED
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
~ ~ ~ +
SYSTEM NOTES.
* 3 Phase AC.
* Permanent live battery feed to Rectifier, ECU, HT Coil (blue wire). Any of these could drain the battery if they were faulty.
* HT Coil is trigered by the BLACK / VIOLET wire being earthed via the ECU.
TESTS:
Stator: Disconected. Any yellow to any yellow = 0.7 - 0.9 ohm. Any yellow to earth = No continuity
Pick Up coil value is not quoted.
Rectifier / Regulator: With a charged battery the possible voltage must not exceed 15.2 volts.
1-9
ZIP 125 Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 NO Immobiliser
Ignition Green
Pick up ON Ignition
Power
OFF
Switch
to
LOCK services
G
ALTERNATOR
Orange
STATOR
Yellow
Orange
Choke Unit
WHITE / BLACK
ORANGE
Purple
PURPLE
To BLACK
2-10
Runner VX / VXR ignition / charging
Piaggio Ltd. 19/07/02 With IMMOBILISER
Green
Ignition Ignition ON
Pick up Power to
Switch OFF
services
Orange
G
ALTERNATOR
STATOR Red
Red
NGK 5
CR 8EB Green amp
Yellow Cooling
Fan Fan
Switch
Red / Blue
Choke Unit
White /
Rectifier / HT Coil Black
Regulator Green
p/n: 82501R
Black
Red Red
6 1 8 3 4 5 7 2 GREEN
WHITE / BLACK
RED / BLUE
Red / Blue
Purple RED
Headlight PURPLE
BLACK
via relay BLUE / BLACK
To YELLOW
Indicator Blue / Black
switch
Grey
/ Red Diagnostic
ECU / Immobiliser
Red / Blue socket Yellow
15
antenna
amp
LED on
Red 3 2 1 Yellow / Red instrument
8 7 6 5 4
pannel
Layout of pins Red
in the ECU / immobiliser
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
10ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-8
Hexagon GTX 125 ignition / charging
Piaggio Ltd. 13/03/02 With IMMOBILISER
Ignition Green
ON Ignition
Pick up
OFF Switch
Orange
G
ALTERNATOR Red
STATOR Red
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue White
Rectifier / HT Coil / Black
Regulator
p/n: 82501R
Black Green
Red Red
GREEN
6 1 8 3 4 5 7 2
WHITE / BLACK
5 3 21
antenna
amp 8 76 54
2-7
ET4 Leader engine ignition / charging
Piaggio Ltd. 13/03/02 With IMMOBILISER
Ignition Green
Pick up ON Ignition
Switch Power
OFF
to
services
Orange
G
ALTERNATOR
STATOR Red / Blue Carb. Heater
RG4HC
CR 9E
Yellow
Orange
Choke Unit
amp
via relay WHITE / BLACK
ORANGE
RED / BLUE
To Purple
Blue / PURPLE
Diagnostic
15 Red / Blue socket
ECU / Immobiliser
amp
3 21 antenna
8 76 54
Red Layout of pins Yellow LED on
in the ECU / immobiliser instrument
Red / Blue pannel
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
9ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-6
DNA 125 / 180 Switch Wiring
Refer to Service Station Manual
Piaggio Ltd. 08/05/2003 594329 (02/01) page 4-23>
1 2 3 4 5 6
ON
OFF
IGNITION SWITCH
LOCK ITEM 6 ON WIRING DIAGRAM
PARK
BLACK
GREEN
OFF
HIGH
LOW
0
SWITCHES
ITEM 8
ON WIRING DIAGRAM
BLACK
GREY - BLACK
YELLOW - BLACK
BROWN
PURPLE
WHITE ORANGE
WHITE - BLUE
BLUE - BLACK
PINK
EMERGENCY
LIGHTS START STOP
ALL PUSH RUN RIGHT HAND
SIDE 0 0
SWITCHES
OFF ITEM 9
ON WIRING DIAGRAM
WHITE
YELLOW - RED
GREEN - BLACK
WHITE - BLACK
ORANGE
BROWN
YELLOW
2-5
DNA Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 DNA 125 / 180
G
ALTERNATOR
STATOR
7.5 7.5
Green amp amp
Power to
Fan Cooling
Lights, horn
Switch Fan Orange
Yellow instruments
Orange
+ BATTERY
3 21
12v ECU
8 76 54
12ah
Black Blue / Red
White / Black Green
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm. YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY, LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-4
B 125 FUSE EXPLANATION
Piaggio Ltd. 08/05/2003 Piaggio Ltd.
WHITE / ORANGE
1 4 amp Engine start, run, warning lights
WHITE
WHITE / RED
12v DC from 2 4 amp Brake lights, start inhibit
ignition switch
RED / GREY
3 7.5amp Horn, Headlight flash
GREY
YELLOW
From light 4 4 amp Anologue, Inst. & side lights
switch
RED
12v DC from battery
5 6 7 8
4 10 15 15
a a a a
YELLOW BLUE
Headlight via relay Under seat, Light, Socket, Lock
2-3
B 125 / 200 NOTES
The notes should be used in conjunction with Service Station Manual 594845 and
the notes “B 125 ignition / charging” and “B 125 Fuse Explanation”
1. Seat has electric release. Only works when ignition switch is in the “off”
position.
If seat lock fails to operate:
Check fuse “7” in rear fuse box. 4 amp red wire in & blue wire out.
Check for power on Blue wire at ignition switch
Check for power on White / Blue wire at ignition switch with ignition “off”.
Check the push button, Blue / Black should earth when button is pressed.
Seat lock, power socket and under seat light are all controlled by the same
fuse.
3. Immobiliser is like other Leader engines. There are separate notes to explain
the immobiliser system.
5. Spark Plugs.
Please note that the correct spark plugs are:
125cc :- NGK CR8 EB p.n. 828866
200cc :- Champion RG6 YC p.n. 828708 (or NGK CR7EB)
2
B 125 / 200 ignition / charging
Piaggio Ltd. 13/08/2003 With IMMOBILISER
OFF
Blue
G
Ignition
Pick up White / Blue Blue / Black
White
White
Cooling
Fan Fan
Green Switch
Yellow Green
Red / Black
White
Ignition Relay
White RUN
STOP
CR 9EB White
Choke Unit White
White / Black
Red / Black
Red / Blue
Yellow / Blue
Blue
White / Green
15 15 4 Red / Black
15
Green Indicator
Black / Blue Switch
HT Coil
ECU / Immobiliser
Purple
3 21
Red Black 8 76 54
antenna
1 2 3 4 5 6
10 7.5 7.5 7.5 5 5
a a a a a a
RED / BLACK
12v DC from battery
BLUE
ORANGE ORANGE
Switched 12v Switched 12v
The wire colours shown here are different to those "on line" and in the owners hand
book.
The colours and fuse functions here are correct, they were checked on GT200
ZAPM312 * 2550.
FUSE:
1. 10 amp. Electric seat release. Headlights. Main beam warning light.
2. 7.5 amp. Intercom. Alarm. Immobiliser LED.
3. 7.5 amp. Intercom. Alarm. Water temp. Fuel warning & guage. Oil pressure warning.
4. 7.5 amp. Horn.
5. 5 amp. Stop light. start switch.
6. 5 amp. Side lights. Number plate light. Instrument panel lights.
MAIN FUSE.
A 15 amp fuse is located at the front of the under seat compartment.
2-14
Vespa GT 125 / 200 ignition / charging
Piaggio Ltd. 18/08/2003 With IMMOBILISER
G
ALTERNATOR Grey
STATOR
Red / Black
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow
Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue
Rectifier / Regulator White / Black
p/n: 82501R HT Coil
Green
Purple
Red / Black
GREEN
6 1 8 3 4 5 7 2
PURPLE
To BLACK
LED on
instrument
Main pannel ECU / Immobiliser
15
antenna 3 21
amp Red / Blue 8 76 54
Layout of pins
Red in the ECU / immobiliser
Note that the ECU fitted to the 125 and 200 have different characteristics.
They are NOT interchangeable.
+ BATTERY
TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12v GREEN TO BLACK (EARTH) = 105 - 124 ohm
12ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2 -13
LEADER Engine
Ignition immobiliser
For a full explanation of the immobiliser system please refer to the Service Station Manual.
The system is very similar to that used on the original Vespa ET4 but there are subtle
differences in operation, fault finding and component replacement. The CDI and immobiliser
are now combined in one box.
The vehicle is supplied with two keys. One MASTER key and one SERVICE key. Additional
service keys are obtainable but it is not possible to duplicate the master key.
TESTING.
Normally do not use the master key for testing.
Testing is done by using the instrument panel mounted LED.
If the system is working normally the LED will be flashing steadily when the ignition is
off and it will stop flashing when the ignition is on.
If the vehicle has not been used for 48 hours the light will stop flashing to save the
battery. It is restored by turning the ignition on and off.
If the immobiliser system is faulty, when the ignition is switched on there will be a series
of flashes. The flashes hold a key to the fault.
Turn on ignition;
1. The first flash will be long (2 seconds) or short (0.7 second). A Long flash means the
system is not programmed. A Short flash indicates that the system is programmed.
2. 2 second pause.
3. Next is a series of short (0.5 second) flashes. These define a fault.
1 flash = System is not programmed. Engine can run but only up to 2000 rpm.
2 flash = No key transponder detected. Fault with Key or antenna.
3 flash = Key transponder detected but not recognised. See the notes below.
4. The last thing to notice is whether the LED finally remains on or off.
OFF = Ignition is possible.
ON = Ignition is not possible.
Notes.
If the system is not programmed the LED indicator may not be flashing with ignition off
but it will perform the test function when the ignition is turned on.
Wrong key. There are a limited number of mechanical codes used for the keys. It is
possible that you could have two vehicles is stock that both have keys with the same
mechanical code. If you put the wrong key in the wrong vehicle it will turn on the ignition
but you will get the “transponder not recognised” fault code and the vehicle will not start.
12
1 of 2
Piaggio Ltd October 2001
Examples.
1 2 3
2 sec
System not programmed.
LED off Engine will only run to 2000rpm.
KEYS
The machine is supplied with two keys. One large brown MASTER key (with a flip out section
containing the chip) and One smaller SERVICE key.
The MASTER key should be kept safely at home. Only use it for programming.
The service key is the key that is used.
If you require a new service key this can be ordered from Fowlers and then programmed as follows:
A quicker easier alternative is to obtain a key from any automotive locksmith. The same system is
common on cars, most locksmiths will have the blanks and the equipment to identify the chip in your
key.
They will cut a key and then fit the correct type of chip into it. This chip will have been “cloned” from
your original so you will not need to programme this new key.
If both keys are lost the only solution is to replace the CDI unit and the locks. A new lock set comes
with a Master and a Service key.
12
2 of 2
Piaggio Ltd October 2001
LEADER ENGINE
Ignition, charging & immobiliser
Use these notes in conjunction with the SERVICE STATION MANUAL
The electrical system on the new Leader engine is very different to previous two stroke and
four stroke Piaggio engines. The ignition, charging & immobiliser circuits do not function in
the same way and do not share common components with previous versions.
Ignition is now using the battery circuit. Everything shares one common supply.
Alternator has three phase (all yellow wires) and ignition pick up coil (green wire) outputs
only.
Rectifier / Regulator is very simple. Three phase (yellow) inputs and one output.
CDI unit has become more complicated. The one unit is responsible for: ignition,
immobiliser, indicators & choke unit.
Much of the circuit is the same on ET4 Leader, Super Hexagon GTX 125, Liberty 125
Leader, Skipper ST, Runner VX / VXR and DNA 125 / 180, X9 125 but be careful
because there are differences. Early Skipper ST did not have an immobiliser, they do have
it now.
IGNITION.
When the ignition is turned on power is supplied to the CDI (terminal 5).
Ignition pick up is via green wire (terminal 2).
Output to the HT coil is via purple wire (terminal 3).
The unit is earthed via black wire (terminal 8).
CDI / IMMOBILISER
Note the CDI units have different part numbers for different models and engines size.
Refer to the diagram for each specific model. The wiring and wire colours may vary.
It is important that the correct part number is used as the ignition characteristics vary and
although the units look the same they are different!
HT COIL. 82597R = Common to most Leader engines. 82582R = Skipper ST & X9 125
Purple to Black - primary winding = 0.4 - 0.5 Ω
HT to Black - secondary winding = 3000 ± 300 Ω
Plugged in with engine cranking the peak voltage Purple to Earth = 100 vdc
11
1 of 2
Piaggio Ltd October 2001
IGNITION PICK UP COIL.
Un plug, check resistance, Green to Black = 105 - 124 Ω
Un-plugged with engine cranking the peak voltage Green to Black = 2 vdc
STATOR.
Any yellow to yellow should give continuity. Un-plugged, yellow to yellow = 0.7 - 0.9 Ω
Yellow to earth should not give continuity.
INDICATORS.
There is no separate indicator relay. The relay function is contained within the CDI unit,
Power to the indicator switch is via the blue / black wire (terminal 1).
If the indicators fail first check that you are getting voltage at terminal 1 (blue/black)
To check the switch and wiring. Unplug the CDI and link red/blue wire to blue/black wire,
when the turn switch is operated the appropriate lights should come on. (you will not need the
ignition to be turned on).
CHOKE UNIT.
The choke is now controlled by the CDI. (not the regulator).
Power is supplied to the choke via the main switched wire from the ignition switch to the
CDI. The unit will not function until the engine is running when the CDI will complete the
circuit to earth (terminal 7).
Un Plugged, resistance across the connections = >< 30 Ω @ 20˚C
Plunger extension. Measure how far the plunger protrudes from the body when it is cold,
this should be 12.5 - 13.0 mm. Now connect the choke unit to a 12v battery. The plunger
should have extended to 18.5 - 19.0 mm within 5 minutes.
Supply. Orange or Red / Blue to earth = Battery volts with ignition on.
Orange or Red / Blue to White/Black = 13-14.5v dc (system volts) with engine running.
11
2 of 2
Piaggio Ltd October 2001
X9 125 / 180 ignition / charging
Piaggio Ltd. 25/10/02 With IMMOBILISER
G
Fan
ALTERNATOR
Red / Black
STATOR Green
Fan Switch
Orange
Choke Unit
Yellow
Grey
/ Black
Lt. Blue Orange
RUN Emergency
STOP Stop
5
Side amp
UP
Stand
DOWN
Switch
Yellow / Green
Yellow / Blue
Rectifier / Red / White
Immobiliser Stand
Regulator LED Warning
p/n: 82501R
Red / Black
Power to 2 GREEN
Yellow 6 YELLOW
Lt. Blue
5 Lt. BLUE
2-9
50cc 4 stroke Charging / Ignition
Piaggio Ltd. 22/11/01 Piaggio Ltd.
STATOR
Test 2 Test 3
BROWN
Test 1
PICK UP SUPPLY TO
INDICATORS
BROWN
GREY / BLUE
1 2 3 4
GREEN INDICATORS
SWITCH
CDI / COIL
BLUE / BLACK
UNIT IGNITION SWITCH
ON
OFF
LOCK
CHAMPION
RG4HC
GREY / BLUE
RECTIFIER
BROWN WHITE WHITE REGULATOR
TO START RED BLACK
RELAY
10A FUSE WHITE GREY
SUPPLY TO
DC SERVICES
Test 4
BLACK
+ BATTERY AC SUPPLY YELLOW / BLACK
TO LIGHTS
12v
CHOKE HEATER
7ah GREY
LIGHTS
ON / OFF
SWITCH
GREY
Only two wires come from the stator. The engine to earth connection is very important.
Battery voltage at idle = 13 v (Battery charged) max will be 14.5 volts at high revs. Meter between battery neg. & pos.
Battery charge at idle = 1.5 - 2 amps (lights off). max will be >5 amps at high revs with all lights on. Meter between red wire and battery pos.
Test 1: Brown - earth = ~170 ohm To test pick up coil. Stator un-pluged
Test 2: Black - earth = ~1 ohm To test charging coils. Stator un-pluged
Test 3: Blue / Grey - earth = 25 - 35 v ac @ 2000 rpm with regulator disconnected. To test charging coils.
Test 4: White - Black = ~8 M ohm. If the resistance is low it could cause the fuse to blow.
10
This information is intended only for authorised Piaggio dealers.
50cc Four Stroke Restriction
Please refer to the notes about the legal implications of de-restricting a moped.
Piaggio do not advocate changing the restriction on any 50cc machine that may be used
on public roads.
Remember that if a Piaggio, Gilera or Vespa 50cc moped is de-restricted it will almost
certainly be technically illegal. It will not conform to Motorcycle legislation but it did
conform to Moped legislation.
The main restriction on the 50 cc four stroke engine is electronic. There is no restriction in the
exhaust pipe.
AC6+0000
38 mm
Cut here
Cut 3 mm deep
at 45º 60 mm
1. Make a 3mm deep cut with a hacksaw in the position shown. Then fill the slot with
silicon.
2. Remove the spacer washer between the front pulley halves.
3. Fit carburettor main jet size #78. Part number 969622
CUT
11
Piaggio Ltd.
X9 250 (Honda engine)
* At PDI
Set the clock TIME and DATE.
Set the TRIP to MILES.
Reset all three SERVICE LIGHTS.
* To change km to miles.
Insert ignition key.
Press and hold down “Trip” and “M” buttons
Turn on the ignition.
The display should now have changed.
* To test System.
With ignition off.
Press and hold down “clock” and “set” buttons
Turn on the ignition
All the systems will check them selves and all the lights should come on.
Any blown bulb or faulty system will be obvious.
* Stop lights.
There are a total of five stop light bulbs.
If two or more bulbs fail the warning light will come on.
* Hazard Lights.
Ignition on
Press hazard button, lights will start flashing.
Turn ignition off.
To stop the lights, first turn the ignition on then press the switch.
* Battery charging.
Charging at idle (1500 rpm) with the main beam on should be 2 amps.
8
1 of 4
Piaggio Ltd. 05/11/02
* Low fuel warning lamp.
The light will only come on when it has received a continuous signal from the sender for 13
seconds.
* Relays.
The vehicle has five relays.
Starter relay p/n 496403 has a 30 amp fuse and is in the battery compartment.
Start Permission relay p/n 292332 is in the battery compartment.
Two head light relays and the main power relay are all the same p/n 58002R they are all
under the front shield, headlights are central and the power relay is on the near side by the
indicator.
* Headlights.
The headlights are controlled by relays and each has it’s own relay so if the light fails and it
is not the bulb, check the relay.
* Choke unit.
Temperature sensor in the radiator can control the choke.
If the temperature drops to 0 degrees C then choke will come on (no voltage to the unit)
* Valve clearance.
Set Cold.
Engine at TDC.
Valve clearance is one division on the scale.
Correct level
* Gear Box Oil Level
Remove the level screw.
If no oil comes out top up until oil drips
then wait until oil stops before re-fitting
the bolt.
* Indicators
The indicator relay function is part of the digital display cluster. P/n. 581413. There is no
separate relay.
The wires involved are:
Blue / Black - right turn
Grey / Blue
Red / Black - left turn
Note that to operate the indicators the handlebar switch shorts the relevant wire to earth.
Hazard lights work by the switch earthing the brown wire from the digital cluster.
8
2 of 4
Piaggio Ltd. 05/11/02
* Braking system
1. Three brake disks are all the same size. 200mm diameter.
2. Both master cylinders are the same size.
3. All brake pads are the same. p.n. 494966
4. L/H front and rear calliper are the same and have 22mm pistons
5. R/H front calliper has 24mm pistons.
6. L/H front and rear are linked together in the following way
When left hand lever is used
Up to 8 bar pressure the rear brake only is operated.
8 - 23 bar both brakes are applied.
Over 23 bar the amount of pressure to the front brakes begins to decrease relative to the rear.
7. The R/H front calliper is operated by the R/H brake lever and has no connection to the other
brakes.
8
3 of 4
Piaggio Ltd. 05/11/02
X9 250 CHARGING & IGNITION
Refer to the X9 Charging & Ignition diagram.
* Note that sometimes the wires coming from a component change colour at the connector that joins
them to the wiring loom.
* See the separate sheet for an explanation of the fuses.
* Charging is three phase, fully rectified.
* Ignition is digitally mapped and can not be manually adjusted.
Spark advance will be affected by:
• Engine speed.
• Throttle position. See # 1
• Coolant temperature. See # 3
8
4 of 4
Piaggio Ltd. 05/11/02
X9 250 Charging & Ignition
Piaggio Ltd. 04/11/2002 Honda Engine
WHITE
RED / YELLOW HT COIL
MAIN POWER DPR7EA-9
FUSES IN
RELAY 15 7.5 7.5 10 FRONT
STORAGE 4
WHITE COMPARTMENT
WHITE / BLACK
RED /
IGNITION BLACK RED BLUE / YELLOW
SWITCH AUTO
2
CHOKE
BLACK
BLACK GREEN FUEL
DIGITAL
RED / RED / INSTRUMENTS THROTTLE PUMP
BLACK POSITION 5
BLACK
SENSOR
1 BLUE / YELLOW
7.5 10 10 20
FUSES IN RED / YELLOW
HELMET
COMPARTMENT
YELLOW / BLACK
RED
GREEN / BLACK
GREY / BLACK
YELLOW / WHITE
STARTER
STARTER MOTOR RADIATOR
RELAY 3 TEMP.
RED
RED / WHITE
BLACK RED
30 amp YELLOW / GREEN
START
RUN
PERMISSION
RELAY 9 ENGINE
RECTIFIER STOP
REGULATOR 10
RED /
GREEN /
BLACK
BLACK
WHITE / YELLOW
7 ORANGE / BLUE
WHITE / BLACK
YELLOW
6
+ BATTERY
12v
12 ah IGNITION
CONTROL
8 UNIT
YELLOW YELLOW
7
LIBERTY 125 Charging Circuit
RECTIFIER / REGULATOR WITH AN EIGHT PIN CONNECTOR
STATOR
Yellow
15 A FUSE
CHOKE White
UNIT Blue / Red + Battery
12v 9ah
Grey
White IGNITION
SWITCH
DC SERVICES
AC SERVICES BRAKE LIGHT
Red / HORN
HEAD LIGHT 7.5 A
Black TAIL LIGHT ETC.
CHOKE Fuse
CONTROL INSTRUMENT LIGHTS
RELAY To Indicator
switch
Blue /
Grey Grey / Blue White Black Black Yellow
1 2 3&4 5 6 7 8
Green / Not used
Black
DC RECTIFIER
AC &
12v DC REGULATOR REGULATOR
from
starter button
Rectifier / Regulator
P/N: 294878
6
Piaggio Ltd. April 1999
HEXAGON 250
Charging & Ignition Circuit
STATOR
White
12 volt 12 ah.
CHOKE
HEATER
Ignition
Ignition Switch
Pick up
15 AMP
MAIN FUSE
Red Red
Yellow
Black Blue / Red
Green Black
SERVICES
RECTIFIER / REGULATOR
Black
Yellow / Black
White / Green
Blue / Yellow
Blue / Red
Red / Black
Green
Black
Spark Plug
IGNITION NGK. DPR6EA-9
SWITCH
See Note
Yellow / Black
White / Green
Green
Black
Green / Yellow
White / Black
Contacts are:
Open to
run.
Green
Closed to
Pink
?
stop.
Fuel Pump
• Note that the wire colour sometimes changes from one side of a conector to the other.
• The choke supply is ><12 volts AC (only when the engine is running).
• The fuel pump senses the engine speed and varies the supply rate accordingly.
TESTING. Green – Black: No continuity with ignition switch and kill switch to Run.
Yellow - Yellow - Yellow: 0.1 – 1.0 Ώ. Stator winding.
Black/Red – Black: 50 – 350 Ώ. Ignition charging coil.
Green/White – Blue/Yellow: 50 – 170 Ώ. Ignition pick up coil
Yellow/Black – Black: 0.1 – 0.2 Ώ. HT coil primary winding.
HT – Black: 3.6 – 4.6 K Ώ. HT coil secondary winding.
5
Piaggio Ltd. March 1999
ET4 (original type) IGNITION IMMOBILISER.
General description
The ignition key contains an electronic digital code; this code must be recognised by the system before
the ignition system will function.
Thus the scooter has two forms of security – the key must physically operate the lock (in the normal way),
and the electronic code must be recognised by the system. In this way the scooter is safe against having
the ignition switch forced, or being hot-wired.
Main components
Decoder, which uses the antenna to read the electronic code of the key transponder.
CDI unit, which latches to the ON position only if an appropriate signal is received from the decoder.
Other components
7.5 amp fuse, which supplies +12V DC to the voltage stabiliser (located within the decoder box).
Voltage stabiliser (located within the decoder box), whose output (+12V DC) supplies power to the
decoder and the CDI unit via contacts in the ignition switch.
“Serial Line”, connects the decoder to the CDI unit, and conveys the authorising signal enabling the CDI
to latch to the “ON” position.
Normal Operation
The key grip contains a passive electronic transponder – a device that contains a unique pre-set digital
code, which can be read without direct electrical contact (similar to those used in the Datatag system).
The keys do not need any power and they do not contain a battery.
When the ignition switch is turned on, the decoder interrogates the key’s transponder.
Only if the decoder recognises the transponder’s electronic digital code will it send a signal via the serial
line to the CDI unit, enabling the otherwise conventional ignition system (alternator with pick-up and
charger coil, CDI unit and HT coil) to function.
However, the CDI unit and the decoder are also programmed to operate together as a matched pair; if
they detect a mismatch the CDI unit will not allow ignition.
4
Piaggio Ltd.
page1 of 6
To check the correct operation of the system
IT IS IMPORTANT THAT ON PDI AND AFTER ANY WORK ON THE IMMOBILSER SYSTEM, THE
CORRECT OPERATION OF THE SYSTEM IS CHECKED.
• Insert the red key with the hinged transponder in the flipped out position (this takes it out of radio
range of the antenna, thus enabling the system to be tested without the antenna automatically picking
up a code).
• Turn the ignition on and try to start the engine. IT SHOULD NOT START.
• Insert the blue key and try to start the engine. IT SHOULD START AND RUN NORMALLY.
Decoder and CDI units are initially manufactured as blank units. In this state (“Virgin”) and up to the time
they are programmed the immobiliser system will not offer any protection, and the ignition will function in
a conventional way. However, a “virgin” unit can be used as a substitute to aid in fault finding.
Programming functions can only be done with a red key. Once either the decoder or the CDI unit has
been programmed using a red key, they will only ever recognise that particular red key.
Therefore, it is vital that you USE ONLY THE BLUE KEY FOR ALL TESTING PURPOSES other than the
programming procedure itself.
If there is any fault with the system, the Immobiliser Test Box should be plugged in to the diagnostic test
socket. The test box (Part no 020319Y, Current dealer price £53.99 + VAT) is an invaluable, time saving
tool, and one which without doubt should be owned by all dealers.
Proceed as follows-
• With ignition off, turn on and wait for ‘On’ and ‘Pronto’ LEDs to illuminate.
• Turn ignition on. The ‘Seriale’ LED will flash, showing the signal on the Serial line.
• After a few seconds the appropriate LED will indicate the result of the diagnostic tests.
If the “No Serial line” LED lights up, it may be for the following reasons-
Serial Line circuit is broken.
Decoder is faulty
CDI unit is faulty
4
Piaggio Ltd.
page2 of 6
Diagnostic points to note-
To check for +12V DC power supply failure, check 7.5 amp fuse, and that +12V DC is present on
decoder terminals 3,5 and 8, and CDI unit terminal 1.
The CDI unit does not have its own earth lead, but is earthed to the alternator stator back-plate via the
white wire from terminal W. However, note also that back-plate and the engine itself is only earthed via
the electric starter motor lead. The decoder has its own earth lead.
There are two different types of transponder/decoder system; each type is not compatible with the other.
However this problem should only show up when trying to program new blue keys. In this case most
automotive locksmiths will be able to “clone” a new blue key if they are provide with a functioning red key.
These “cloned” keys will be recognised by the system without the need for programming.
CDI unit 1. Replace CDI unit (CDI can be replaced on its own).
2. Check for correct operation of system. Note that with a
virgin CDI unit the engine will start and run normally, but
the immobiliser system is inactive.
3. Program the CDI unit simply by turning on the ignition
switch using the red key
When programming keys do not have more than one transponder type key on the key ring, as the
decoder may pick-up both transponders.
4
Piaggio Ltd.
page3 of 6
VESPA ET4 IMMOBILIZER DIAGNOSTICS
When fault finding the ignition system on VESPA ET4, there is a very simple and quick check, which can
be done to give the Immobiliser the ‘all clear’. If you don’t have the effort-saving Immobiliser Tester (part
no. 020319Y) then insert a 12 Volt LED in the 2 pin socket (the blue/black lead is negative) located under
the helmet compartment and switch on the ignition whilst observing the LED. Note that the LED marked
Seriale on the Tester display shows this same signal.
It is advisable to get into the habit of using the blue key for all use and testing purposes other
than the programming procedure itself.
Normally-Functioning Immobiliser
The signal for a normally functioning Immobiliser system is a quick flash (0.7 seconds) and then the LED
remains off.
Immobilizer Fault-Finding
If the system is not functioning normally, it is recommended to obtain the Piaggio Immobiliser Tester. This
is by far the easiest way to diagnose faults. However, if for some reason this is not available, fault finding
can be done by observing the following.
2 secs 2 secs
LED off
0.5 secs
The above diagram shows the trace of the diagnostic signal for Decoder and CDI Units both
programmed, using a key with an unknown transponder (Table 2, case 5), resulting in 3 FLASHES during
the second phase of the diagnostic signal (Phase 2).
Phase 3: LED remains OFF if no fault is detected or ON if a fault is detected in the Immobilizer system
(the Tester does not consider a non-programmed CDI Unit a fault).
4
Piaggio Ltd.
page4 of 6
Table 1: Immobilizer Diagnosis Chart
Phase 2
LED Signal DIAGNOSIS
0 FLASHES NORMAL OPERATION
1 FLASH BREAK IN SERIAL LINE (ORANGE) OR DECODER EARTH (BLACK)
2 FLASHES NO TRANSPONDER DETECTED - FAULTY KEY OR IMMOB. ANTENNA
3 FLASHES TRANSPONDER DETECTED BUT NOT RECOGNISED BY IMMOB.
4 FLASHES VIRGIN DECODER AND PROGRAMMED CDI UNIT
KEY:
P = UNIT PROGRAMMED
V = VIRGIN i.e. UNPROGRAMMED
Y = ANTENNA FUNCTIONING
N = ANTENNA ABSENT or NOT FUNCTIONING
9 = IGNITION POSSIBLE
= IGNITION NOT POSSIBLE
PROG. = TRANSPONDER RECOGNISED THROUGH PROGRAMMING PROCEDURE
ANY = KEY WITH TRANSPONDER PRESENT BUT CODE DOESN’T MATTER
NOTES:
1. BLUE KEY - use for testing ignition after replacing Decoder and / or CDI Unit, otherwise you may
sacrifice perfectly good units; programs both Decoder and CDI Unit.
RED KEY - only use for programming operations and ONLY when you are sure the ignition system is
delivering a satisfactory spark.
The EXCEPTION to the above two points is when testing the Antenna with the RED KEY transponder
flipped out, as per the ET4 Service Station Manual.
2. LIMITED TO 2000 rpm
3. Normal operation with the either key
4. Break in the Serial line (orange lead) or Decoder not earthed properly (black lead)
4
Piaggio Ltd.
page5 of 6
4
Piaggio Ltd.
page6 of 6
Vespa ET4 (ZAPM04) charging circuit
From ZAPM04 * 51160 07/08/2002 8 pin regulator
YELLOW
2
7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
WHITE
ON
BLUE
OFF
GREEN
GREEN
BLACK WHITE
1
DC SERVICES
GREY / BLUE Brake light
Horn
WHITE
AC
GREY / BLUE
BLACK
Head light
TO INDICATOR
Tail light
WHITE / RED BLUE / BLACK SWITCH
Instruments
3&4 YELLOW
GREY
NOT
USED
1 2 3 4 5 6 7 8
RECTIFIER
REGULATOR &
REGULATOR
GREY
* This diagram shows the later (non Leader) ET4 wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* The charging system is basically the same as the 50cc & 80cc two stroke Sferoids.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay.
* The choke is supplied with 12v DC when the ignition is turned on but the circuit to earth is only completed
when the engine is running and 12v AC is supplied to the choke control relay.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
3
Vespa ET4 (ZAPM04) charging
Up to ZAP04 * 51159 07/08/2002 5 pin regulator
WHITE
CHOKE CONTROL
GREEN
WHITE
WHITE / RED
GREEN / BLACK
YELLOW GREY
+12v DC from
start button
AC SERVICES DC SERVICES
GREY / BLUE
1
YELLOW
WHITE
GREY
BLACK
RED
A A G B+
3
RECTIFIER BATTERY +
REGULATOR &
REGULATOR 12v
* This diagram shows the early ET4 (non Leader) wiring using a five pin connector on the rectifier / regulator.
Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* Three completely separate circuits for AC, DC & ignition.
AC is full wave and regulated
DC is half wave rectified and regulated
Ignition is the self powered CDI type typical on our two stroke scooters. Shorted to earth to stop.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is powered by the DC circuit but the relay to activate it is controled by the AC circuit.
Circuit will only be completed when both:
AC is present at relay terminal "B" and +12v DC is NOT present at the unmarked terminal.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
2
Coguar 125 Charging & Ignition
Piaggio Ltd. 07/08/2002 Honda XL125 engine
RECTIFIER / REGULATOR
PICK
UP
YELLOW YELLOW
STATOR
YELLOW YELLOW
YELLOW YELLOW
RED RED
GREEN BLACK
STAND
UP
SWITCH
FUSES STAND DOWN
1 X 20 AMP WARNING
1 X 15 AMP LIGHT DPR8 EA9
WHITE / GREEN
NEUTRAL
LIGHT NEUTRAL
SWITCH
STARTER
BUTTON
M CLUTCH
SWITCH
STARTER
RELAY
IGNITION
+ BATTERY UNIT
WHITE / GREEN
YELLOW / RED
12v BLUE
BLACK
WHITE / BLUE
NOTES
Three phase charging with inductive low voltage ignition.
The start & run permissive circuit is shown here in grey.
TESTS
Stator: Any yellow to any yellow = 0.8 ohm. Any yellow to earth should give NO continuity.
Regulated voltage: 14.0 - 14.8 volts with fully charged battery and lights on. Engine running at 5000 rpm.
1
X9 250 FUSE EXPLANATION
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
BLUE
1 20 amp Under seat light / Power socket
RED
WHITE / RED
12v direct from 2 10 amp Headlight relay
battery
RED / BLUE
3 10 amp Headlight relay
RED / BLACK
RED / BLACK
12v from battery 4 7.5 amp Digital Instruments
via start relay
1 2 3 4
15 7.5 7.5 10
a a a a
9
H@K & GSM Charging / Ignition
Piaggio Ltd. 23/04/02 Gilera engine
RED
WHITE
GREEN
ORANGE
RECTIFIER
REGULATOR BROWN
YELLOW
YELLOW
ORANGE
12v DC Services
FUSE
RED RED
IGNITION + BATTERY
SWITCH
12v
ON
OFF
R O G B
GREEN
RED
WHITE
ORANGE GREEN
GREEN RED
* Stator has separate coils for AC, DC and Ignition circuits. Champion N2C
Brown wire = supply for DC (battery circuit) NGK BR9ES
Yellow wire = supply for AC circuit
Green wire = supply for ignition
* Important that Stator has a good earth to engine and engine
must have good earth to chassis and battery.
* All Lights are powered by 12v AC
* Ignition is self generating and does not need the other electrical
circuits or the battery.
* Ignition is stopped by shorting the charge coil (green wire) to CDI / Coil
earth.
Check: Unplug Green wire from stator and CDI unit. You should
have continuity from green to earth with ignition OFF and no
continuity with ignition ON.
1
VESPA T5 HORN
Blue
HORN HORN SWITCH
NORMALLY ALTERNATOR
CLOSED
Yellow
Green
Black
REGULATOR
The T5 has a very simple 12 volt AC electrical system but one thing may not be clear
when you look at the wiring diagram.
It appears that the output from the alternator goes firstly through the horn, this does
not make much sense. If you are fault finding it is important that you understand how
the system works.
Explanation:
1. Out put from the alternator is the blue wire to the horn switch.
2. Horn switch is normally closed.
3. From there the yellow wire continues to the regulator.
4. Electricity always takes the easy path, so the current passes through the switch
rather than through the coil in the horn.
5. When the horn button is pressed and the circuit is broken and then the current will
have to pass through the horn and the horn will sound.
6. Power still reaches the regulator because the horn does not use all the power
available and it does not break the circuit.
7
Piaggio Ltd. October 1998
PX 125 / 200E Indicator Circuit
Piaggio Ltd. 06/08/2002 Piaggio Ltd.
NOTE.
The indicators flash alternatley; front - back (not both together)
This is to reduce the current needed
IDICATOR SWITCH
RIGHT
OFF
LEFT
PINK BLUE
BROWN WHITE
RED PURPLE
RED
WHITE / BLUE
PURPLE
WHITE
NOTE.
Turn Buzzer p/n 231284
could be connected to GREEN
INDICATOR
red / black or white if RELAY
required grey
red
blue
white / red
RED / BLACK
C B G G
WARNING
LIGHT ON
INSTRUMENT
PANEL
RED
RECTIFIER / REGULATOR
6
PX 200 / 125 Start Permissive circuit
Refer to Service Station Manual
Piaggio Ltd. 23/01/2003 578666 section 4
M BLACK PINK
Permissive switch
STARTER
MOTOR WHITE-RED
PINK
YELLOW GREY
ON IGNITION
WHITE
SWITCH Starter Protection
OFF
Relay
Located under
RED
WHITE horn cover
RED
RED
7.5 amp
FUSE + BATTERY
12v
RED
RED GREY
C B G G G
5
VESPA PX 125 / 200 Charging & Ignition
Piaggio Ltd. 04/07/02 Electronic Ignition
ON
DC OFF IGNITION
SWITCH
SERVICES YELLOW LOCK
GREEN
WHITE
RED
WHITE GREEN
RED
FUSE
+ BATTERY
7.5 12v
AMP
9ah
AC
RED GREY
SERVICES
RED / WHITE GREEN
C B G G
* AC output is regulated, full wave.
* DC output is regulated and half wave rectified.
* Alternator coils are connected in series.
REGULATOR
& * Ignition is self generating and totaly self contained.
DC RECTIFIER
REGULATOR
TESTS.
1. ALTERNATOR OUTPUT.
Unplug regulator. blue and earth = 26 - 30 vac @ 3000 rpm.
Unplug stator. red to white = 90 -140 ohms. green to white = 800 -1100 ohms.
2. BATTERY CHARGING.
Insert an ammeter betwen red wire and battery +.
With engine @ 3000 rpm and battery @ 13 vdc the ammeter should read 1.5 - 2 amps
* IN CASE OF OVER CHARGING.
un-plug the regulator and check that you have battery voltage on the red / white wire
that plugs into terminal "C". The regulator needs this input to function correctly.
* Check for good earthing between engine and chassis / battery / regulator.
4
H@K & GSM Notes
Modifying the exhaust.
Piaggio can not recommend de-restricting for any reason. Be aware that if a moped is
de-restricted then it becomes a 50cc motorcycle and should be re-registered. These
vehicles may not conform to the requirements to become a motorcycle.
Un-officialy and to save possible damaging experimentation the following information
is given.
Enlarge the hole in the end of the exhaust, where it plugs into the engine.
The end of the exhaust is a piece of mild steel bar with a small hole drilled through it,
this hole needs enlarging to about 18 - 20mm (3/4 inch).
The steel bar is case hardened to comply with “anti-tamper legislation”. To soften the
hardening; heat the end to bright cherry red and then let it cool naturally. Then you
should be able to drill it.
Re-jet with a #60 or 62 main jet. It is a standard DellOrto jet.
Engine To silencer
2
Piaggio Ltd. 22/12/00
Gilera RCR 50 Charging / Ignition
Piaggio Ltd. 09/09/2003 Derbi engine
LIGHTS
WHITE
ON
RED
OFF GREEN
RN2C
RED / BLACK
WHITE / RED
BR9 ES
BLUE
RED
CDI
and
HT COIL
GREEN / BLACK
4A FUSE
RED RED
OUTPUT
TO DC
SERVICES
+ BATTERY
12v
GREEN / BLACK
REGULATED
GREEN
OUTPUT
WHITE
RED
TO OUTPUT
INDICATOR TO AC
SWITCH SERVICES
YELLOW
RED / BLACK
ORANGE
YELLOW
RED
L + C YELLOW
G
GREEN
RED
WHITE
The Derbi electrics are arranged differently to Piaggio systems. Please study this carefully.
Earth wires are: YELLOW / GREEN.
Ignition is separate to AC & DC circuits. Ignition is shorted to earth to stop the engine.
STATOR OUTPUT. GREEN to EARTH = 610 ohms + 10% (CDI charging coil)
RED to EARTH = 80 ohms + 10% (Ignition pick up coil)
YELLOW to EARTH = 0.9 ohm + 10% (AC & DC circuit charging coil)
HT COIL secondary. 3.4 K Ohms + 15%. PLUG CAP. 5 K OHMS + 15%
4-8
X9 RANGE.
CHANGING THE ODDOMETER DISPLAY TO SHOW MILES
This should be done at PDI. See manual 594284. Pages 9-4 and 4-57
1. Press and hold the TRIP and M buttons.
2. Turn on the ignition.
3. Release the buttons
The display will now show “miles”.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights
will come on at the correct time. Service Station Manual 594284 4-61 and owners
hand books have details for setting the clock.
If when you briefly press the button the light that comes on is not the one before
the one you want to reset then briefly press the button again to make the light
scroll along.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the
digital instrument panel and Black is to earth.
1
PIAGGIO LTD 04/11/02
X9 UNDER THE FRONT PANEL
The front panel between the headlights is retained by five cross head screws.
Remove the panel to access the service light reset button and the two headlight
relays.
It is not necessary to remove the panel to adjust the headlight beam. The adjuster
screw can be accessed through the small grill near the top of the panel.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights
will come on at the correct time. Service Station Manual 594284 4-61 and owners
hand books have details for setting the clock.
RE-SETTING THE SERVICE LIGHTS
If one or more of the service lights is flashing follow this procedure:
1. Turn on the ignition. One of the three service lights is flashing.
2. Briefly press the button. The light before the one you want to reset should light.
3. Press and hold the button. The light you want to reset will start flashing faster.
While it is flashing fast release the button. Now the light should have gone out.
4. Turn off the ignition and turn back on to prove the light has been cancelled.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the digital
instrument panel and Black is to earth.
2
Piaggio Ltd. 04/11/02
Fuel Gauge & Sender Circuit
Piaggio Ltd 04/11/2002 Piaggio Ltd
Fuel Gauge
Low fuel
FUEL warning
A
C
B
WIRING
A = BLACK
Float B = GREEN / YELLOW
C = GREEN / WHITE
TESTS
A-C
Low fuel level >< 100 ohms
High fuel level >< 3 ohms
5
Piaggio, Vespa, Gilera
AUTOMATIC CHOKE OPERATION
The automatic choke units used on Piaggio scooters are all basically the same and all work in the
same way.
Remember that the choke defaults to being ON so it is unlikely that a cold starting problem is due
to a malfunctioning choke.
Operation.
• The choke unit has a plunger that is pushed down to close off a hole at the bottom of a drilling
in the carburettor.
• A wax pellet is heated electrically and expands, as it heats up it pushes out the plunger. As the
wax warms the electrical resistance measured across it increases until it becomes open circuit.
In most circumstances the choke will then remain off purely by the heat of the engine.
• The time taken for the choke to turn off is controlled only by the rate at which the wax expands.
The ambient temperature will affect the time taken for the choke to turn off. Cold weather will
mean the choke stays on longer etc.
• The choke is activated once the engine has started and not when the ignition is turned on.
50 & 80 cc two stroke engines.
These scooters have headlights that are run from 12 volts AC.
12 volts AC is used to operate the choke. AC can only be supplied when the engine is running so
the choke can not begin to turn off until the engine is running.
125 & 180 cc two stroke engines.
These engines have an all 12 volt DC system.
When the ignition is turned on there is 12 volts supplied to the choke but the circuit is not
completed to earth and no current can flow. So the choke will not turn off if the ignition is left on
before starting the engine.
When the engine starts the rectifier / regulator completes the circuit to earth (via the grey wire) and
the choke will turn off during the next few minutes.
125 four stroke engines. (not Leader)
Sfera 125 uses an AC system like the 50 / 80 cc engines.
ET4 employs a relay so that the choke will be powered by DC but is triggered by the AC supply
when the engine starts.
Leader four stroke engines.
These engines have an all 12 volt DC system.
When the ignition is turned on there is 12 volts supplied to the choke but the circuit is not
completed to earth and no current can flow. So the choke will not turn off if the ignition is left on
before starting the engine.
When the engine starts the CDI unit completes the circuit to earth (via the white / black wire) and
the choke will turn off during the next few minutes.
50 four stroke.
Connected to the AC output from the rectifier / regulator so power is only available when the
engine is running.
250 Hexagon & X9 250 (Honda engines).
AC powered by one of the three phase (yellow) wires direct from the generator.
4
1of 3
Piaggio Ltd. August 2002
Faults.
The most likely fault is the choke remaining ON. Symptoms will be anything that may be caused by
a rich mixture.
1. High fuel consumption.
2. Black spark plug.
3. Rough running when hot. OK when ridden hard but rough and four stroking at 20 mph.
4. Fails to start. Plug is found to be black and fouled.
Note. Remember that the choke defaults to being ON. If the choke does not turn off the symptom
will be a black and fouled plug. Or; The scooter starts and idles ok and runs at speed ok. When
riding slowly (15 - 20 mph) the engine runs very roughly.
4
2of 3
Piaggio Ltd. August 2002
Dia.2. Choke unit power supply.
Choke
DC powered choke
V 1. Ignition off = 0 volts
2. Ignition on = 12 volts
3. Engine run = 13-14.5 volts
Note. Choke units all look much the same but are different and it is important to use the correct
choke in the correct carburettor.
4
3of 3
Piaggio Ltd. August 2002
STATOR COIL VALUES
Refer to the relevant Service Station Manual / wiring diagram
Vehicle Ign. Pick Up Ign. Charging AC Circuit DC Circuit
50cc 2T Red - White Green - White Blue / Grey - Earth Yellow - Blue Red - Battery Positive
88 Ω (± 5 Ω) 970 Ω (± 50 Ω) 25 - 30v AC 25 - 30v AC 1.5 - 2 amp (charged bat.=13v)
Runner 125 Red - Brown Green - White n/a Yellow - Yellow
Hexagon 2T 90 - 140 Ω 50 - 150 Ω 27 - 30v AC
Liberty 125 Red - Brown Green - White Blue / Grey - Earth Yellow - Red Red - Battery Positive
ET4 original 100 - 130 Ω 300 - 400 Ω 25 - 30v AC 26 - 30v AC 1.5 - 2 amp (charged bat.=13v)
Skipper 2T Red - Brown Green - White n/a Yellow - Yellow
Typhoon 125 90 - 140 Ω 100 - 160 Ω 27 - 30v AC
Leader (all) Green - Black n/a n/a Any yellow - yellow 0.7 - 0.9 Ω
125 / 180 105 - 124 Ω Yellow to earth = no continuity
Hexagon 250 Green / White - Blue / Yellow n/a n/a Any yellow - yellow 0.1 - 1.0 Ω
GT & GTX 50 - 170 Ω Yellow to earth = no continuity
X9 250 White / Yellow - Yellow n/a n/a Any yellow - yellow >< 0.6 Ω
>< 200 Ω Yellow to earth = no continuity
X9 500 Engine speed & position sensor n/a n/a Any yellow - yellow 0.2 - 1.0 Ω
3
Test to be carried out with the stator un-plugged and engine stopped.
Test to be carried out with rectifier / regulator disconnected and engine running.
Test to be carried out with rectifier / regulator and battery disconnected.
Test with unit unplugged.
B (Beverly)
Clock and trip counter will re-set if voltage drops below 4,5v. Total distance record is “non-
volatile” and can not be affected.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold down the MODE and CLOCK buttons
3. Turn on the ignition
4. Miles or Km will be displayed to show which is selected. Turn off and start again to change it
DNA
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See manual 564329 page 4-42. The manual says that the change can
only be made if less than 6km show on the total distance. This is no longer true, the change can
be made as often as needed at any distance.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
ICE
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See manual 564811 page 4-13.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
X9
Clock.
The clock time and date functions MUST BE SET AT PDI. Because some of the service
light intervals are controlled by this.
6
1 of 2
Piaggio Ltd. 04/11/02
Service lights.
There are three lights on the display to remind the owner that certain servicing is due. These
lights are controlled by elapsed mileage and elapsed time so it is important to set the date
correctly at PDI. If you do not do this you may find the lights come on at the wrong time (and
you will get a grumpy customer).
OIL: Comes on after first 1000km (625 miles) and then after every 3000km
SERVICE: Comes on after first 1000km and then after every 6000km.
This light also comes on after one year even if the distance has not been covered.
BELT: Comes on after every 18000km.
Don’t forget to reset service lights when you do a service, even if they are not flashing
(scooter has come in early). If you do not do it the customer will be back in a few days with a
light flashing. That makes you look bad and again you have a grumpy customer.
It is probably worth going through the re-set procedure for all three lights at PDI because if
the battery had been connected previously the counter will have started from the wrong day.
ZIP
The Zip now has electronic instruments. The speedometer is still the traditional analogue
display but it is now electronically controlled. The odometer is now digital LCD. It is
supplied showing the distance in Km. It can be changed to show miles but only if it is
changed during the first 10km. CHANGE IT AT PDI.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold the button on top of the leg shield.
3. Turn on ignition. LCD display will show “Cont” (km) or “EnGL” (miles)
4. Briefly press button to toggle between the two alternatives.
5. When the correct press and hold the button for more than one second.
6. Turn ignition off. Turn back on to confirm the setting is now correct.
Re-setting the “Change Oil” warning.
At 6000km an oil change warning will be displayed on the LCD display for 10 seconds every
time the ignition is turned on. Cancel this at service.
1. Press and hold the button at top of the leg shield.
2. Turn on ignition on.
3. Release button and turn ignition off. Turn ignition back on to check that the warning has
been cancelled.
6
2 of 2
Piaggio Ltd. 04/11/02
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
Vacuum
tap
Vent
control
Balance pipe
Pump driven by crank valve
case depression Supply to
carburettor
Vent to
atmosphere
One way Pump
valve
Typhoon 80 and 125 have an auxiliary fuel tank located under the front panel. The
plumbing for this fuel system looks complicated. The Typhoon parts catalogue contains a
illustration which should help you locate the components on the vehicle. The diagram
above is intended to help explain the operation of the system and should prove useful when
fault finding.
VENT TO ATMOSPHERE The system has only one vent which you will find exiting under
the rear mudguard.
VENT CONTROL VALVE Controls venting to prevent loss of fuel from full tank. Air can
enter the tank without restriction but a slight pressure is required before vapour can exit.
AUX TANK VENT Auxiliary tank vents to the main tank via a pipe that has to run under the
foot boards. Because this pipe gets lower than the tank level it can become full of fuel and
so the auxiliary tank will not vent. To prevent this a limited flow ONE WAY VALVE allows
any fuel to be sucked out.
A large diameter BALANCE PIPE lets petrol flow between the two tanks.
A smaller diameter pipe passes through the PETROL PUMP which pumps petrol from the
auxiliary tank to the main tank.
Petrol PUMP is driven by the vacuum/pressure pulses from the crank case.
Note that the BALANCE PIPE stands up into the main tank so once the fuel level reaches
that point the pump will drain the auxiliary tank and all the remaining fuel will be in the main
tank. Because of this layout the fuel gauge does not drop at a steady linear rate. If you start
with a full tank, fuel is used in the following three phases:
1. Fuel used from main and auxiliary tanks equally - Gauge will drop from full to ¼ .
2. Level remains constant in main tank while auxiliary is drained - Gauge remains at ¼ .
3. Fuel is used only from main tank - Gauge drops from ¼ to empty.
VACUUM TAP is operated by vacuum from the inlet manifold.
1
1 of 2
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
FAULT FINDING
If you suspect that the fault is due to lack of fuel. Firstly prove that the carburettor is
running out of fuel.
Attach a piece of clear tube to the float bowl drain and turn it up the side of the
carburettor.
Open the drain screw. you will now be able to view the fuel level. It should remain about
3.5mm below the float bowl joint. If you find it is low or it drops during running then you
should explore the fuel supply.
If you have a problem that suggests a poor supply of fuel to the carburettor.
1. Check that you have fuel in the main tank. If you have fuel then you can forget about
the front tank and its associated plumbing, this can not affect the supply to the
carburettor.
Not able to get 7 litres of fuel in scooter with a nearly empty tank.
Auxiliary tank is not being used for some reason.
1. Check pump. With engine running you should see the pumped fuel coming out of the
pipe in the main tank.
2. Check for pinched pipes particularly under foot boards and helmet compartment.
3. Check auxiliary tank vent is clear of fuel (one way valve not working).
Scooter runs ok on bench but customer says it cuts out when ridden.
1. Pipe trapped under helmet compartment is squashed by weight of rider.
1
2 of 2
PUMPED FUEL SYSTEMS
Explanation of differences on Piaggio and Gilera scooters
DNA 50. ZAPC27 Hexagon 250 GT. ZAPM14 Runner VXR. ZAPM24
DNA 125. ZAPM26 Hexagon GTX 125 ZAPM20 Typhoon 80 TE81T
DNA 180. ZAPM26 Runner 50 ZAPC14 Typhoon 125 ZAPM02
Hexagon 125. EXS1T Runner FX. ZAPM07 X9 125. ZAPM23
Hexagon 125 LX. ZAPM05 Runner FXR ZAPM08 X9 250. ZAPM23
Hexagon 180 LXT. ZAPM06 Runner VX. ZAPM24 X9 500 ZAPM27
4
2 of 2
Piaggio Ltd. 04/11/02
HEXAGON EXS1T fuel system.
HEADER TANK
HEADER TANK
VENTING PIPE
MAIN TANK
CARBURETOR
FILTER
PUMP
CRANKCASE
3
Piaggio ltd. August 2001
DNA FUEL SYSTEM
Piaggio Ltd. 04/11/2002 PAGE 1 OF 2
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
VACUUM
TAP
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
2
DNA FUEL SYSTEM
Piaggio Ltd. 04/11/2002 PAGE 2 0F 2
MANIFOLD
VACUUM
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Early 50 NOTES:
1. Carburettor is gravity fed not pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
Later DNA 50
MANIFOLD
VACUUM
VACUUM TAP
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Later 50 NOTES:
1. Carburettor is pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
2
VESPA PX FUEL TAP
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
CLOSED
OPEN
RESERVE
5
KEYS.
All Leader engined vehicles with immobilisers
Notes:
Only the Service key should be used day to day. The Master key should be kept
safely at home.
Use the Service key for testing and fault finding. Only use the Master key for
programming.
It is not possible to programme a replacement master key to a previously
programmed immobiliser.
It is possible to programme new Service keys only if you have the original Master
key.
Original Service keys with a chip fitted can be recognised by this symbol
etched into the metal near the top.
Keys Galore – London – 020 7586 9741 First Access – Herts - 0115 967 6466
Express Keys – Kent – 01689 850008 Auto Keys – London – 020 7586 9741
10
Piaggio Ltd. 04/11/02
GILERA TYRES & WHEELS
2000 / 2001 / 2002 / 2003
MODEL FRONT REAR
chassis prefix wheel tyre bar wheel tyre bar
Coguar 125 custom ZAPM17 2.50 x 17 100 / 80 - 17, 52 S T 1.8 3.00 x 17 130 / 70 - 17, 62 T T 2.0-2.2
DNA 125 / 180 ZAPM26 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 14 140 / 60 - 14, 64 P T/L 2.2– 2.5
DNA 50 ZAPC27 3.50 x 14 120 / 70 - 14, 55 L T/L 1.8 3.50 x 14 140 / 70 - 14, 62 T/L 2.0
GSM 50 super motard VTBC08 2.50 x 17 110 / 80 - 17, 52 T T 1.4 3.50 x 17 130 / 70 - 17, 62 T T 1.6
H@K 50 trail bike VTBC08 1.40 x 21 80 / 90 - 21, 48 P T 1.4 1.85 x 18 110 / 80 - 18, 58 P T 1.6
Nexus 500 (due August 2003) ZAPM35 3.50 x 15 120 / 70 - 15, 56 H T/L 2.2 4.50 x 14 160 / 60 - 14, 65H T/L 2.5
Ice 50 ZAPC30 3.00 x 10 120 / 90 - 10, 56 J T/L 1.3 3.00 x 10 120 / 90 - 10, 56 J T/l 1.8
RCR 50 trail bike VTHSDR1EB 80 / 90 - 21 T 1.0-1.1 110 / 80 - 18 1.2-1.3
Runner 50 all versions ZAPC14 / ZAPC362 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner 50 Purejet ZAPC361 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner FX125 / FXR180 (rear drum) ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner FX125 / FXR180 DD ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 13 130/60-13, 60 P T/L 1.6-2.2
Runner VX125 / VXR180 ZAPM24 3.50 x 12 120 / 70 - 12, 51 L T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner VXR200 ZAPM24 3.50 x 12 120 / 70 - 12, 51 P T/L 1.4 3.50 x 12 130 / 70 - 12, 56 P T/L 1.6-2.2
SMT 50 super motard VTHSDR1FB 110 / 80 - 17 T 1.7-1.8 130 / 70 - 17 2.0-2.1
8
STALKER 50 (previously SKP) ZAPC13 / ZAPC401 3.50 x 10 120 / 90 - 10, 56 J T/L 1.2 3.50 x 10 130 / 90 - 10, 61 J T/L 1.6-2.0
GFR 125 race replica 167 3.00 x 17 110 / 70 - 17, 54 T T/L 1.8 4.00 x 17 150 / 60 - 17, 65 T T/L 2.0-2.2
Nordwest 600 super motard 228 3.50 x 17 120 / 70 - 17, 60 R T/L 2.1 4.50 x 17 160 / 60 - 17, 60 R T/L 2.3-2.4
RC 600 trail 228 1.85 x 21 90 / 90 - 21, 54 T T 1.8 2.50 x 17 130 / 80 - 17, 65 T T 2.0-2.2
Saturno 350 & 500 café racer 222 3.00 x 17 110 / 70 - 17, 53 H T/L 2.1 4.00 x 17 160 / 60 - 17, 68 H T/L 2.3
XRT 350 / 600 trail 224 / 218 1.85 x 21 90 / 90 - 21, 54 T T 1.8 2.50 x 17 130 / 80 - 17, 65 T T 2.0-2.2
Chrono 125 race replica 164 2.50 x 16 100 / 80 ZR 16 T/L 1.8-2.0 3.00 x 17 130 / 70 ZR 17 T/L 2.0-2.2
Apache 125 trail 1.85 x 21 90 / 90 - 21, 54 R T 1.8 2.50 x 18 120 / 80 - 18, 62 R T 2.0-2.2
Freestyle 125 super motard 2.50 x 16 100 / 80 - 16, 50 S T/L 1.8-1.9 3.00 x 17 130 / 70 - 17, 62 S T/L 2.0-2.2
CX 125 race replica 158 3.50 x 17 120 x 60 ZR 17 T/L 2.1-2.2 4.00 x 17 150 / 60 ZR 17 T/L 2.3-2.4
Bold type denotes a current model. This list was last updated on 31 July 2003
Identify a vehicle by its chassis prefix AND model name.
Typhoon 125 ZAPM02 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 50 / Typhoon 50 RST TEC1T / ZAPC19 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 80 TE81T 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Velofax 50 VTAC02 1.60 x 17 70 / 90 - 17, 43M T/L 2.0 1.85 x 16 80 / 90 - 16, 46M T/L 2.5-3.0
Vespa ET2 50 two stroke ZAPC16 / ZAPC381 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 50 four stroke ZAPC26 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 125 four stroke ZAPM04 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 2.50 x 10 130 / 70 - 10, 62L T/L 1.8-2.0
Vespa ET4 Leader 125cc four stroke ZAPM19 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa PX125 VNX2T or ZAPM093 2.10 x 10 3.50 - 10, 51J T 1.25 2.10 x 10 3.50 - 10, 51J T 1.75-2.3
Vespa PX200 VSX1T / ZAPM18 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75-2.3
Vespa GT 125 / 200 ZAPM311 / 312 3.00 x 12 120 / 70 - 12, 51P T/L 1.8 3.00 x 12 130 / 70 - 12, 62P T/L 2.2
Vespa T5 Classic VNX5T 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75 - 2.3
X9 125 ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.1 3.50 x 14 140 / 60 – 14, 64 P T/L 2.3 – 2.5
X9 250 ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 13 140 / 60 - 13, 63P T/L 2.2 - 2.5
X9 500 ZAPM27 3.50 x 14 120 / 70 – 14, 55 S T/L 2.2 3.50 x 14 140 / 70 – 14, 68 S T/L 2.3 – 2.6
X9 500 fitted with dedicated top box 2.4 2.3 - 2.6
Zip 2000 Cat two stroke ZAPC25 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8 - 2.0
Zip 50 two stroke SSL1T 2.15 x 10 90 / 90 - 10, 50J T/L 1.2 2.15 x 10 90 / 90 - 10, 50J T/L 1.7 - 2.5
Zip RST 50 two stroke ZAPC06 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 100 / 80 - 10, 52J T/L 1.8
Zip SP 50 two stroke ZAPC11 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 110 / 80 - 10, 52J T/L 1.8
Zip 125 four stroke ZAPM25 2.50 x 10 100 / 80 - 10, 53L T/L 1.6 3.00 x 10 120 / 70 - 10, 54L T/L 2.0
Bold type denotes a current model. This list was last updated on 31 March 2003. Identify a vehicle by its chassis prefix AND model name.
Oil list
Vespa ET2 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Vespa ET4 50 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Vespa ET4 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Vespa ET4 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Vespa PX 125 2 str. Synthetic 2 stroke API TC or higher - 4 spd 80W GL4 or higher 250cc n/a - - sealed unit - Air -
Vespa PX 200 2 str. Synthetic 2 stroke API TC or higher - 4 spd 80W GL4 or higher 250cc n/a - - sealed unit - Air -
Piaggio B (Beverly) 125 / 200 4 str. 5W-40 synthetic API SJ or higher 1.1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio Deisis 100 2 str. Hi Scooter 2 Tech - CVT - Gear 80W-90 light gear GL3 or higher 110cc sealed unit - Air -
Piaggio Hexagon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon LX125 / LXT180 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GT 250 4 str. 20W-50 synthetic API SG or higher 800cc CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16 1.82 ltr.
Piaggio Hexagon GTX 125 / 180 (11") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GTX 125 / 180 (12") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio Liberty 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 30cc Air -
Piaggio Liberty 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 95cc 20W 90cc Air -
Piaggio Liberty 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Air -
Piaggio NRG 50 water cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16 900cc
Piaggio NRG 50 air cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Piaggio Skipper 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Piaggio Skipper ST 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Air -
Piaggio Typhoon 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Typhoon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio X9 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.2 ltr.
Piaggio X9 250 4 str. 20W-50 synthetic API SG or higher 1.1-1.3 CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Ethelyne Glycol Cuna NC 956-16
Piaggio X9 500 4 str. 5W-40 synthetic API SJ or higher 1.7 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.8 ltr.
Piaggio Zip 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 20W 25cc Air -
Piaggio Zip 50 4t 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 25cc Air -
Piaggio Zip 125 (single sided fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio Zip 125 (telescopic fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 60cc Air -
Gilera DNA 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera DNA 125 / 180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera GSM / H@K 50 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 500cc Chain - - ? ? Ethelyne Glycol Cuna NC 956-16
Gilera Coguar 125 4 str. 20W-50 synthetic API SG or higher 1.2 ltr. 5 spd. integral with engine - Chain - - 10W 280cc Air -
Gilera Ice 50 (front fork marked "TH") 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 72cc Air -
Gilera Ice 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 90cc Air -
Gilera Runner 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner FX125 / FXR180 (early) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner FX125 / FXR180 (late) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera Runner VX125 / VXR180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera SKP (Stalker) 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Gilera GFR 125 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 1.3 ltr. Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16
Gilera Saturno 350 / 500 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - ><7.5W 310cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera Nordwest 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera RC 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 640cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
SPARK PLUGS
PIAGGIO / VESPA mm NGK Champion
B 125 (Beverly) 125 (& 200) four stroke 0.7-0.8 CR8 EB RG4 HC
B 500 (Beverly) 500 four stroke 0.7-0.8 CR7 EKB RG6 YC
Cosa 125 , 150 0.6 B9 ES (BR9 ES) N2C (RN2C)
Cosa 200 0.6 B7 ES (BR7 ES) N4C (RN4C)
Free 50 (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon 125 &180 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon GT250 & GTX 250 (Honda 4 stroke) 0.8-0.9 DPR6 EA9
Hexagon GTX 125 four stroke 0.7-0.8 CR9 EB RG4 HC
Liberty 50 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Liberty 125 four stroke (original version) 0.7-0.8 CR9 E RG4 HC
Liberty 125 Leader four stroke 0.7-0.8 CR7 EB RG6 YC
Liberty 125 Leader four stroke (heavy use) 0.7-0.8 CR8 EB RG4 HC
NRG 50 water cooled (heavy use) 0.5-0.6 BR10 ES RN1C
NRG 50 (air or water cooled. All versions) 0.5-0.6 BR9 ES RN2C
Quartz 50 0.5-0.6 BR9 ES RN2C
Sfera 125 four stroke 0.5-0.6 CR9 E RG4 HC
Sfera 50 & Sfera 80 (all versions) 0.5-0.6 BR9 ES RN2C
Skipper ST 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Skipper 125 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Velofax 50 two stroke 0.5-0.6 BR9 ES RN2C
Vespa 50 Special & PK50S 0.6 B6 HS L86
Vespa ET2 50 two stroke (carburettor) 0.5-0.6 BR9 ES RN2C
Vespa ET4 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Vespa ET4 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Vespa GT 125 0.7-0.8 CR8 EB RG4 HC
Vespa GT 200 0.7-0.8 CR7 EB RG6 YC
Vespa Primavera ET3 0.6 B7 HS
Vespa Primavera & PK 125 0.6 B6 HS
Vespa PX 125 0.5-0.6 B7 HS L82C
Vespa PX 200 0.5-0.6 B7 ES (BR7 ES) N4C (RN4C)
Vespa T5 Classic 125 0.6 B9ES (BR9 ES) N2C (RN2C)
X9 125 (Piaggio 4 stroke engine) 0.7-0.8 CR8 EB RG4 HC
X9 250 (Honda 4 stroke engine) 0.8-0.9 DPR7 EA9
X9 500 (Piaggio 4 stroke engine) 0.7-0.8 CR7 EKB RG6 YC
Zip 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Zip 50 2 stroke (all versions, inc. catalytic) 0.6-0.7 BR9 ES RN2C
Zip 125 four stroke 0.7-0.8 CR7 EB RG6 YC
GILERA
Coguar 125 (Honda 4 stroke engine) 0.8-0.9 DPR8 EA9
DNA 125 & DNA 180 four stroke 0.7-0.8 CR8 EB
DNA 50 two stroke (catalytic) 0.6-0.7 BR9 ES RN2C
H@K & GSM 50 2 stroke (Gilera engine) 0.5-0.6 BR9 ES RN2C
H@K & GSM 50 2 stroke (Derbi engine) 0.-0.
ICE 50 two stroke catalytic 0.6-0.7 BR9 ES RN2C
Nexus 500 four stroke
Runner VX125 & VXR180 four stroke 0.7-0.8 CR8 EB
Runner 50, 125 & 180 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Runner 50 “Purejet” direct injection 2 stroke 0.6-0.7 RG6 YCA
SKP 50 two stroke 0.5-0.6 BR9 ES RN2C
OLDER GILERA MOTORCYCLES
Saturno 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Dakota 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Nordwest 600 four stroke 0.6-0.7 DPR9 EA9
RC 600 four stroke 0.6-0.7 DPR8 EA9
CX 125 & Apache & Crono & Free-Style 2 st 0.6-0.7 B10 EG - BR9 EG N82 - C55
GFR 125 two stroke 0.6-0.7 B10 EGV C55C
06/05/03
7-5
Up side down Forks
Piaggio Ltd. 07/08/2002 Typhoon / Runner etc.
Nylon Bush
Upper Circlip
Upper Circlip
Nylon Bush
Lower Circlip
Dust Seal
Tapered groove
Nylon Bush
Fork Leg
Lower Circlip
Fork Stanchion
Forks are grease filled for lubrication. The grease can be expected to work past the nylon bush so the chrome stanchion will get a
dirty ring round it.
Damping is by a sealed hydraulic damper cartridge in the left leg. The cartridge is held at the bottom by a bolt that will be found in the
bottom of the axle mounting. The top of the damper rod is held by a nut on top of the top yoke. If the seals in this unit fail you will find
oil dripping from the bottom of the left leg.
Some 50's did not have the damper. To check if a damper is fitted: look for the nut on top of the left leg, no nut means no damper.
To separate the fork leg:
1. Remove damper top nut (from left leg only).
2. Remove the dust seal.
3. Remove the bottom circlip.
4. Pulling the stanchion hard will force the upper circlip out of the tapered groove, the circlip and bush will be pulled out.
On very early forks the top circlip groove was not tapered so it will be necessary to pull the bush out to get to the circlip.
To pull the bush out:
1. Lubricate the bush with WD40 or similar.
2. Carefully screw two small self tapping screws into the nylon bush and pull it out using two pairs of pliers.
Note that there are several manufactures of these forks and although they look the same the internal components may not be
interchangeable between makes.
4
PISTONS AND SMALL END BEARINGS
Small End Bearing sizes.
Small end needle roller bearings fitted to two stroke twist and go engines and PX
engines are supplied in four sizes they are colour coded for identification.
The end of the con rod will either be colour coded or it will be marked with a
series of lines.
Piston sizes.
Piaggio use alloy or cast iron barrels on different engines. Alloy barrels can not
be re-bored and over size pistons are not available. Oversize pistons are
available for cast iron barrels. These are listed as 1M, 2M, 3M.
In addition to oversize there will be four pistons listed for all engines as “FC” or
FC1, FC2 etc. These are tolerance fittings.
Pistons can be matched to barrels in two ways. Either by referring to the
tolerance data page near the front of the appropriate Service Station Manual or
by referring to the marking on the crown of the piston and the top of the barrel.
On some engines barrel and piston will both have a letter stamped into them.
Both letters should match. The lowest (first) part number will be the smallest piston
and first in this list.
Remember, if you are measuring barrel and piston you should always measure in
line with the gudgeon pin because they will have worn oval. Most wear occurs
at right angles to the gudgeon pin.
3
Piaggio Ltd. August 2001
PX 200 / 125 “COSA” TYPE CLUTCH
The COSA type clutch is now fitted to the PX 200 & PX125.
It can replace the old type clutch as a complete assembly. p/n 433548 (200cc) p/n 288650 (125cc)
NOTE
CHAMFER
Piaggio Ltd. May 2000
FITTING NEW MAIN BEARINGS TO TWO STROKE AUTO’S
Replacing the main bearings is not a difficult job but it MUST be done the correct
way to ensure a correct fit.
The problem can be that you do not achieve the correct end float in the crank so
the bearings are being side loaded. This will cause a bearing failure within a very
short time (200 miles max!)
It is vital that the end float is checked with a dial gauge once the cases have
been bolted together.
The following assembly procedure is the ONLY way to do the job. It is the quickest
and easiest. Also it almost guarantees correct tolerance. Please do it this way:
1. Heat the bearings in engine oil. First signs of smoke from the oil is hot enough!
About 100 degrees
2. Support the crankshaft vertically. Drop one bearing onto crank. If it will not drop
on (by gravity) it is not hot enough. If you have to tap it home, ONLY use a
piece of tube to act on the centre race. NEVER hit the outer race. Once it is on
leave it to cool.
3. Turn crank over and drop other bearing on. Leave it to cool completely.
4. Position the drive side crankcase half on its side with inside facing up. Support it
on blocks of wood so the crank can be dropped in (again, just using gravity).
1
1 of 4
Piaggio Ltd. 10/03/03
5. Hear the case with a hot air gun, mostly heat it around the area where the
bearing will fit. Don't try to hurry this. It is hot enough when the rear end of the
case is too hot to keep you hand on.
6. When it is hot enough then drop the crank / bearing in and leave it to cool. If it
will not drop in easily then the case is not hot enough yet.
7. Once it is completely cold turn the case over so the crank is hanging down and
then fit the crank removal tool 20163Y (50cc) or 20262Y (125 & 180cc) as if you
were going to press the crank back out of the case.
8. Tighten the extractor bolt as tight as you can by hand. This will push the crank
out against the bearing so all the free play in the bearing has been removed
and the crank is pushed out as far as it can go. Do not use a spanner to tighten
the bolt or you may move the bearing. Tightening it by hand can not move the
bearing (you ain't that strong).
2 of 4
Piaggio Ltd. 10/03/03
9. Now position the other crank case half on the blocks of wood (inside facing up)
heat it as before and drop the crank / crank case onto it.
10. Fit the cases together with liquid gasket (not silicon). Don't forget the water
pump impeller on water cooled engines. Bolt it up and leave it to cool.
11. Once it is completely cold remove the special tool. Now use a dial gauge to
measure the end float. Pull the crank one way, notice the gauge reading and
then push it the other way. You MUST have 0.03 - 0.09mm free play.
12. If you have nearly got the free play try hitting each end of the crank with a
nylon hammer and check again.
13. If you have not got enough free play there is no point carrying on. Take it apart
and do it again (I would recommend using new bearings just in case the others
have been damaged!).
The reason for establishing the end float is to ensure that there is no side load on
the bearings. Ball races do not like side load and they will fail very quickly.
Checking the free play guarantees that the bearing is not side loaded and the
balls can run centrally in the bearing tracks.
Please do not try and improvise. Make sure you have all the correct tools for the
job. They are a very good investment for time saved and stress avoided.
If you have any questions please give your Regional After Sales Manager a call.
3
3 of 4
Piaggio Ltd. 10/03/03
Section through
Main bearing
1. The top diagram shows a bearing correctly fitted with no side load.
Only the whole load is being transmitted through the balls.
2. The lower diagram shows a bearing that has a side load. The inner and outer
tracks are being pushed in opposite directions.
The balls are now transmitting the load at an angle and the side force has the
effect of forcing the balls up a ramp (the shape of the track). The balls are
trying to push the inner and outer tracks apart. Because of the ramp effect the
force applied is far higher than just the side loading. So now the tracks are
being subjected to not only the normal load but also another huge load.
In addition the extra load may force the lubrication away from the point of
contact so you will have a dry metal to metal contact rather than a film of oil
separating the parts.
4
4 of 4
Piaggio Ltd. 10/03/03
FITTING NEW MAIN BEARINGS TO TWO STROKE AUTO’S
The problem can be that you do not achieve the correct end float in the crank so
the bearings are being side loaded. This will cause a bearing failure within a very
short time (200 miles max!)
It is vital that the end float is checked with a dial gauge once the cases have
been bolted together.
1. Heat the bearings in engine oil. First signs of smoke from the oil is hot enough!
2. Drop one bearing onto crank. If it will not drop on (by gravity) it is not hot
enough. Once it is on leave it to cool.
3. Turn crank over and drop other bearing on. Leave it to cool completely.
4. Position drive side crank case half on its side with inside facing up. Support it on
blocks of wood so the crank can be dropped in (again, just using gravity).
5. Hear the case with a hot air gun, mostly heat it around the area where the
bearing will fit. Don't try to hurry this. It is hot enough when the rear end of the
case is to hot to keep you hand on.
6. When it is hot enough then drop the crank / bearing in and leave it to cool.
7. Once it is completely cold fit the crank removal tool 20163Y (50cc) or 20262Y
(125 & 180cc) as if you were going to press the crank back out of the case.
8. Tighten the extractor bolt as tight as you can by hand. This will push the crank
out against the bearing so all the free play in the bearing has been removed
and the crank is pushed out as far as it can go. Do not use a spanner to tighten
the bolt or you may move the bearing. Tightening it by hand can not move the
bearing (you ain't that strong).
9. Now position the other crank case half on the blocks of wood (inside facing up)
heat it as before and drop the crank / crank case onto it.
10. Fit the cases together with liquid gasket (not silicon). Don't forget the water
pump impeller. Bolt it up and leave it to cool.
11. Once it is completely cold remove the special tool. Now use a dial gauge to
measure the end float. Pull the crank one way, notice the gauge reading and
then push it the other way. You MUST have 0.03 - 0.09mm free play.
12. If you have nearly got the free play try hitting each end of the crank with a
nylon hammer and check again.
13. If you have not got enough free play there is no point carrying on. Take it apart
and do it again (using new bearings!).
The reason for doing this is to ensure that there is no side load on the bearings. Ball
races do not like side load and they will fail very quickly.
Checking the free play guarantees that the bearing is not side loaded and the
balls can run centrally in the bearing tracks.
If you have any questions please give your After Sales Representative a call.
1
1 of 2
Piaggio Ltd. 04/11/02
Section through
Main bearing
1. The top diagram shows a bearing correctly fitted with no side load.
Only the whole load is being transmitted through the balls.
2. The lower diagram shows a bearing that has a side load. The inner and outer
tracks are being pushed in opposite directions.
The balls are now transmitting the load at an angle and the side force has the
effect of forcing the balls up a ramp (the shape of the track). The balls are
trying to push the inner and outer tracks apart. Because of the ramp effect the
force applied is far higher than just the side loading. So now the tracks are
being subjected to not only the normal load but also another huge load.
In addition the extra load may force the lubrication away from the point of
contact so you will have a dry metal to metal contact rather than a film of oil
separating the parts.
1
2 of 2
Piaggio Ltd. 04/11/02
SERVICE LIMITS
NEW LIMIT Or change at:
50cc 2T
(Inc. Purejet) Belt - 17.5mm 15,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 20,000 km
50cc 4T
Oil 850cc 6000 km
Belt - 17.5mm 12,000 km
Rollers 18.9mm 18.5mm -
125cc 2T
Belt - 21.0mm 12,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 30,000 km
125cc 4T orig.
Oil 850cc 5000 km
Belt 17.2mm 10,000 km
Rollers 18.5mm -
125cc 4T Leader.
Oil 1 ltr. 6000 km
Belt 22.5mm 21.5mm 12000 km
Rollers 19.0mm 18.5mm -
B 125 Brake Disks 4.00mm 3.50mm -
180cc 2T
Belt - 20.5mm 12,000 km
Rollers - 19.5mm -
Oil Pump Belt - - 30,000 km
180cc 4T Leader.
Oil 1 ltr. 6000 km
Belt 20.5mm 19.5mm 12000 km
Rollers 20.6mm 20.0mm -
250cc 4T Hex
Oil 800cc 3000 km
Belt 21mm 18000 km
Rollers 23.8mm 23.2mm -
250cc 4T X9
Oil 1 ltr. 3000 km
Belt 23.3 22.3 18000 km
Rollers >< 23mm 22.5mm -
500cc X9
Oil 1.7 ltr. 6000 km
Belt 26.2mm 25mm 12000 km
Rollers 24.9mm 24.5mm Check 12000 km
Front Disk 4.00mm 3.50mm -
Rear Disk 5.00mm 4.50mm -
15
Piaggio Ltd. 04/03/03
QUICK REFERENCE GUIDE
FIRST SERVICE is always at 1000 km (625 miles)
Older engines used variator rollers that needed greasing. Later greasless rollers can be fitted
to early variators. If greased rollers are used lubricate sparingly at every service (except
first): Use only “Jota” grease p.n. 494643
125 4t. (Original) air cooled GT 250 / GTX 250 (Honda Helix)
Check oil level by sight glass. Check oil level with dipstick screwed OUT
Engine Oil: 10w40 synthetic. 850 cc. Engine Oil: 800cc (1ltr after strip) 10w40
Oil Change: 3000 km Oil change: 3000 km
Service: 6000 km. Service: 6000 km
Rear Hub: 80w Light Gear. 90 cc. Rear Hub: 150cc 10w40
Fuel: Min 95. Unleaded. Coolant: 1.82 ltr.
Tappets: 0.15 mm. 50/50 with distilled water
Ign. Timing: 10° @ 1500. 32° @ 6000 rpm. Tappets: Back off one division
Idle: 1600 – 1800 rpm Ign. Timing: 12° @ 1500. 27° @ 7000 rpm
Slow running: 3.5 turns out. (out to richen) Idle: 1500 rpm.
CO: 3.5% (hose on exhaust outlet) Slow running: 2 ¾ turns out (out to richen)
Spark Plug: 0.7 - 0.8 mm CO: not quoted
Champion RG4HC Spark Plug: 0.8 - 0.9mm
NGK CR8E (colder) NGK DPR6EA9
Rollers wear limit: 18.5 mm min. dia. Pulley wear limit: 0.4mm
Belt wear limit: 17.2mm (min width) Belt wear limit: 21mm (min width)
Change Belt: 10,000 km (24 mths) Belt Change: 12,000 km (24 mths)
14
2 of 3 Piaggio Ltd. 04/03/03
125 4t Coguar. Honda XL125 engine 100 2t. Diesis. Derbi engine
Check oil level with dipstick screwed out. Service: 5000 km (12 mths)
Engine Oil: 1.2 ltr. 20w50 synthetic SG Hub Oil: 110cc - 80w90 light gear oil
Oil change: 3000 km Spark Plug: 0.6 - 0.7 mm
Service: 6000 km Champion RN2C
Tappets: in:0.10 mm. ex: 0.10 mm NGK BR9 ES
Ign. Timing: 15° @ 1400. 32° @ 3450 Belt change: min width = 16mm
Idle: 1400 rpm. 5000 km (12 mths)
Slow running: 2 turns out (out to richen) Then every 10,000 km
CO: 5% + 0.5%
Spark Plug: 0.8 - 0.9 mm 500 4t Master
NGK DPR8 EA9
Check oil level with dipstick screwed IN
Chain size:
Engine Oil: 1.7 ltr 5w40 synthetic SJ
Oil change: 6000 km (check @ 3000 km)
50 2t H@K, GSM. Gilera engine Service: 6000 km (12mths)
Service: 5000 km (12 mths) Rear Hub: 250cc 80/90 light gear oil.
Gearbox Oil: 500cc - 10w40 4t engine oil Coolant: 1.8 ltr. 50 / 50 mix
Spark Plug: 0.5 - 0.6 mm Tappets: in: 0.15mm. ex: 0.15 mm
Champion RN2C Idle: 1450 rpm. + 50 rpm.
NGK BR9 ES CO: 1.25% + 0.25%
Chain size: 415 x 124 links CO2: 14.5% + 1%
Spark Plug: 0.7 - 0.8mm
Champion: RG6YC
50 2t PUREJET. Direct injection NGK: CR7 EKB
Service: 5000 km (12mths) Rollers wear limit: 24.5 mm min.dia.
Hub Oil: 75cc - 80w90 light gear oil Belt wear limit: 25 mm width.
Spark Plug: 0.5 - 0.6 mm Belt Change: 12,000 km or 24 mth.
Champion RG6 YCA Air Filter Change: 18,000 km or 36 mth.
NGK ? Fuel Filter Change: 48,000 km
Belt width: 17.5 mm min width
Belt change: 15,000 km (36mths)
Rollers: 18.5 mm min.dia.
Fuel Filter: 10,000 km (24 mths)
Mixer belt: 20,000 km
If there is ever any doubt about service intervals for a vehicle, always use the intervals shown in
the owners handbook.
Piaggio recommend fully synthetic oil for all engine applications.
Piaggio have never offered any tuning parts for any vehicles and we will never recommend
tuning or de-restricting a vehicle for any reason.
All 50cc vehicles are only available as “mopeds” restricted to 30mph.
All current 125cc vehicles are “Learner Legal” producing less than 15 hp (11kw). They are not
restricted If they are tuned they will not be learner legal and warranty will be affected.
14
3 of 3 Piaggio Ltd. 04/03/03
PIAGGIO / VESPA / GILERA
CHASSIS NUMBER LOCATION.
Ice 50
Remove the black central cover over the oil tank filler. The Chassis number is
stamped into the main chassis tube on the off side just below the oil filler cap.
Liberty, Free
Chassis number is stamped onto a plate attached to the frame on the off side
above the cooling fan cover.
Velofax
Chassis number is stamped into the underside of the rear carrier (part of the
frame).
X9 125, 180, 250 & 500. B (Beverly) 125, 200 & 500
Lift seat. Pull up the internal carpet at the rear. Remove the small panel in the
floor toward the rear. Chassis number is directly below.
DNA, H@K, GSM and older Gilera motorcycles, Nordwest, RC600, GFR etc.
The chassis number is stamped into the right hand side (off side) of the head
stock.
A duplicate of the chassis number will not be found in any other location. If the
number has been removed it will not be possible to identify the vehicle.
Most vehicles now have a specification sticker, which is most likely to be under the
seat. Along with the Homologation and specification details you should find the
chassis number. This metallic sticker is often removed or lost.
13
Piaggio Ltd. November 2002
Restriction Notes
Never discuss the technicalities of how to de-restrict with end users. But, advice given can
prevent problems caused by them fiddling blindly.
Piaggio have never supplied any information about how vehicles are restricted or how to make
them go faster.
Piaggio can not advocate de-restriction for any reason.
Vehicles will only have been homologated as Mopeds so will be technically illegal if they are
de-restricted.
Piaggio have never offered any tuning parts.
If a 50 is de-restricted the licensing requirements will be the same as a 125, so Piaggio’s official
line is “Do not de-restrict, if you want to go faster get a 125”
125cc engines are not restricted, they are designed to produce no more than 11 kw. So they will be
learner legal.
50cc engines are always restricted and are only sold as 50 km/h mopeds. There is no “full power”
option. Most countries in Europe have the same 50 km/h category.
Restriction of 50cc 2 stroke geared engines. H@K & GSM. See Chapter 4 page 2
Only restriction is a restrictor in the inlet end of the exhaust pipe.
A two size larger main jet will be needed. A standard DellOrto part.
If de-restriction is carried out by an authorised dealer, Piaggio are happy that the warranty will not
be affected. Any tuning or fitting of after market parts by the end user or the dealer will affect the
warranty.
12
1 of 2
50cc Moped restriction information
What is a moped?
A Moped is a two wheel vehicle of no more than 50cc with a design top speed of 30 mph (on the
flat).
All current Piaggio, Vespa and Gilera 50cc two-wheel vehicles are restricted and are only supplied
as Moped’s. They are only tested and homologated as mopeds.
Piaggio do not recommend de-restricting or modifying for any reason.
If the vehicle may be used on a public road. The person carrying out the modification must take full
responsibility for the possible implications of their actions.
If a Moped is de-restricted.
1. It becomes a 50cc Motorcycle.
DVLA should be informed and the vehicle re-registered.
2. It may not conform to motorcycle requirements and may not be legal.
For example; Lighting requirements are different for Mopeds and Motorcycles.
Piaggio can not give any assurance that a de-restricted vehicle will be technically legal.
3. A motorcycle licence will be required.
A 50cc motorcycle has the same licence requirement as a 125cc.
A Motorcycle can not be ridden on a provisional motorcycle licence before basic training is
completed (CBT).
A full car licence allows a moped to be ridden but not a 50cc motorcycle.
4. A rider must be at least 17 years old.
A 16 year old can ride a Moped but not a 50cc Motorcycle.
5. The Insurance company who are insuring the vehicle should be informed.
The premium will probably be un-affected but any modification should be notified to the
insurer in writing. Insurance will be invalid if the vehicle is modified and the insurer not
informed.
Remember that if the vehicle or the rider is not legal then the insurance will be invalid.
6. Piaggio Ltd. Are happy that the warranty will remain valid if the de-restriction is carried out by
an authorised dealer.
If any “tuning” or fitting of non Piaggio parts is carried out then the warranty will be invalid.
Piaggio’s advice has to be: If you want to go faster, get a 125.
Recently a 16 year old was stopped for speeding, when the Police realised his age they immediately
charged him with.
1. Exceeding the speed limit.
2. Riding a motorcycle with no motorcycle licence (he was under age).
3. Riding a motorcycle without valid insurance.
The dealer who did the de-restriction was charged and found guilty of aiding and abetting!
The boy’s father attempted to sue the dealer!
A disclaimer may be of little use as a defence. Be warned! If someone rides to your shop and asks
you to de-restrict then rides away they will be breaking the law and they have only been able to
break the law because you helped them.
If you get a disclaimer signed one of the conditions should be “I do not intend to use this vehicle on
public roads” and another should be “I am fully aware of the legal implications of having my
vehicle de-restricted and I am prepared to take full responsibility for this”.
12
2 of 2
ALARM CONNECTION
ADAPTERS ALARMS
Connector 445143
OLD only Hexagon # EXS1T
SWITCH
445152 445149 = Fido 2
Not ET4 / PX / EXS1T (600171M)
600712 M Replacement key = contact Piaggio Ltd
Additional adapter {
445150 = Fido 2
602095 M Battery backup
Not ET4 / PX / EXS1T Replacement key = contact Piaggio Ltd
No adapter needed
only DNA 50, 125, 180 600447 M000E
Mini - Full
Supplied with one key
602097 M Spare key = 602092M
Not ET4 / Leader / PX
/ EXS1T
Connector
600897M
SWITCH only ET4 (not Leader) 602154 M00E
1999 > Mini - Self Powered
Supplied with two keys
(not used on PX) 602169M00E Spare key = 602092M
Not ET4 / Leader / PX
/ EXS1T
The new LEADER engine has a very different electrical system and an adapter for this is not
available yet. Do not try to use any existing adapter.
{ The additional adapter 600712M is used to convert the old style harness so it can be plugged into
the new style ignition switch.
11
1 of 2 Piaggio Ltd. 04/11/02
Alarm Information
There are four alarms supplied by Piaggio:
Fido: suitable for Vespa PX
Fido 2: Needs a wiring adapter to connect it to the vehicle wiring. Suitable for many of the older
models. Check the fitting list for compatibility.
Mini Full: More compact unit. Needs a wiring adapter. Suitable for many models.
Check the fitting list for compatibility. Mini Full will plug directly into the DNA wiring harness.
Mini Full Self Powered: Similar to Mini Full but with battery back up. The wiring socket is
different to the Mini Full and it requires specific wiring adapters. Check the fitting list for
compatibility.
Wiring adapters are not currently available for Leader engines. Leader engined vehicles are
supplied with an immobiliser as standard. Except the DNA which has a socket to allow the Mini
Full to be plugged into it directly.
Programming new keys for Mini Full and Mini Full Self Powered alarms.
Additional keys can be obtained from Fowlers. Part Number is 602092M (Same for both alarms)
Programming:
1. Ignition off.
2. Disconnect the red wire (remove the fuse).
3. Press and hold the anti-theft button (shorts the black/grey wire to earth)
4. Re-connect the red wire while holding the anti theft button.
5. Check that the vehicles LED has come on and the alarm emits a sound.
6. Press the new remote control key button.
7. The alarm should now beep and the LED will turn off. This signals that the code has been
accepted.
The alarm can remember up to eight keys at a time. If a ninth key is programmed then the first one
will be forgotten.
If you have any problems with these alarms contact Piaggio Ltd. Accessory Department 020 7401
4329.
Remember that a faulty alarm will not be covered by warranty. It is covered by a twelve month
guarantee from Fowlers of Bristol.
11
2 of 2 Piaggio Ltd. 04/11/02
GILERA KEYS
The following photograph shows the different types of keys used on the recent
Gilera models.
Only the Runner VX / VXR has an immobiliser. Note the symbol on the key that
denotes an immobiliser chip is fitted.
Later Runner FX / FXR keys look the same as the VX / VXR key but they do not have
an immobiliser chip and the symbol is not on the key.
Runner FX / FXR = the shape shown in the picture is 563585 this has been
superseded to 576719 this looks like the VXR key but does not have an immobiliser
chip.
SKP 50 = 574690
ICE 50 = 576719
9
Piaggio Ltd. 04/11/02
Chapter 1
Electrical systems
Electrical Systems
Electrical Systems
Electrical Systems
Two Stroke
Manual Engines
Electrical Systems
General
Fuel Systems
Mechanical Systems
ON
Ignition Switch
15 amp
Red / Blue
Fuse's in
Orange
Battery
Compartment
Blue
Red
White
B
Black
E
Yellow
S
Black / Blue
L Oil Tank Low Oil
Sender Warning
Light
White
White / Red
Yellow Yellow
Black / Blue
Turn
Indicator
Switch
Right Turn Indicators
Left Turn Indicators
* The low oil warning light check function is controlled by the indicator relay.
* The oil check light should come on for 15 seconds when the ignition is first turned on.
* If the system fails: first check the 7.5 amp fuse located under the front grill (horn) panel.
1 - 10
DIESIS 100 Charging / Ignition
Piaggio Ltd. 11/06/02 Derbi engine
Yellow / Green
Yellow / Green Indicators NGK
RIGHT B9 ES
OFF
LEFT
Yellow
Yellow / White
AC Supply Black / Red
Yellow
Red + 5o C Green / Black
Yellow / Green
Thermostat
Ignition Switch
Green / Black
DC Supply Black Carb. Heater LOCK
Black OFF
ON
Red
Red / Blue Green
4 Red Orange
To amp Yellow / Green Black Red / White
starter
solenoid
+ BATTERY
Orange - Indicator switch Red / Blue - DC supply
Rectifier
Earth wires are - Yellow / green. Indicator
Regulator &
Relay
Yellow wire is AC supply. Regulator
Red / Blue wire is DC supply.
Engine earth is very important.
Carb heater is driven by AC power via a thermostat.
No separate Ignition pick up, CDI is triggered by the AC wave.
Ignition is earthed to stop the engine.
TESTS.
Stator: Yellow - Earth = min 25 v AC. White / Red - Earth = min 30 v AC. Engine at mid rpm.
Yellow - Earth = 0.9 ohm + 0.2. White / Red - Earth = 1.1ohm + 0.2. Stator un-plugged.
Black / Red - Earth = 238 ohm + 10%. Stator un-plugged.
Regulator: Yellow - Earth = 13.5 + 0.5 v AC. White / Red - Earth = 13.5 + 1.0 v DC. Engine at mid rpm.
Ignition: HT coil secondary resistance = 5 - 6 K ohm. Unit un-plugged.
8
FUSE EXPLANATION
Runner FX 125 & FXR 180
Notes.
• Ignition circuit is completely separate and self powered. It does not have any fuses.
• The cooling fan is permanently live and is protected by the main 25 amp fuse.
• The starter motor supply is not fused.
3
Lighting
Switch
7
125 / 180 2T Ignition
Hexagon LX / LXT
IGNITION SWITCH
ON
OFF
GREEN BLACK
GREEN
STAT OR
WHITE
BROWN
RED PURPLE
R B W G V
IGNITION TIMING IS CDI CONTROLLED
Not adjustable
CDI UNIT
Skipper and Typhoon:
Meter between > Red - Brown White - Green Purple - Earth HT lead - Earth
Skipper / Typhoon 125 90 - 140 ohm 100 - 160 ohm 0.5 + ohm
0.025 + k ohm
4.8 0.25
NOTES.
* The ignition circuit is a separate self-contained circuit with no fuses and no connection to the other
electrical circuits on the vehicle. It has a separate charging coil in the stator (Green & White wires).
* The ignition switch contacts are OPEN when the engine is RUNNING. Contacts are CLOSED when
switch is turned OFF, this allows the system to discharge to earth. When fault finding, if there is no spark
then check the "green" and "purple" wires to see if there is a "leak" to earth. Unplug stator & CDI, check
* A "Resistor" type spark plug and a resistor plug cap should always be fitted.
* This circuit does not require the engine to chassis earth. But if that earth lead is missing it is possible that
trying to use the starter motor could force excess current through the CDI and damage it.
6
125 / 180 Two Stroke INDICATOR CIRCUIT
Piaggio Ltd 06/08/2002 Piaggio Ltd
BLACK
STARTER STARTER
RELAY SWITCH
INDICATOR
RELAY
BE
L B
+ 12V DC OIL WARNING
LAMP
S
STOP SWITCH
BLUE / RED
YELLOW
BLACK / BLUE
INDICATOR SWITCH
ABOVE. Vehicles 1999> Cirduit with oil check light that comes on when ignition is switched on.
Refer to the Service Station Manual. Also Technical Notes 2/99 and 3/99.
BELOW. Vehicles <1999 Circuit with oil check light that comes on when brake is held on and starter
button is pressed.
WHITE / RED
INDICATOR
RELAY
STARTER
LOW OIL RELAY
WARNING
OIL WARNING SWITCH
LAMP
DIODE
INDICATOR SWITCH
BLACK / BLUE
5
125 & 180cc 2t charging / Ignition
Typhoon, Skipper, Hexagon, Runner
WHITE YELLOW
BROWN
RED IGNITION
PICK UP
GREEN
STATOR
RED
BATTERY +
YELLOW
12v
FUSE
RED
IGNITION SWITCH
ON
OFF
COOLING FAN
ON
WATER COOLED
PURPLE GREEN RED MODELS
WHITE
SUPPLY
CDI TO
Unit SYSTEMS
NOTES
* Choke and Carb' heater will have a supply with ignition turned on but the
rectifier / regulator will only complete the circuit to earth when it detects a CHARGE
charge. I.e. the engine is running. WARNING
* The Charge warning light goes out when the engine is charging because +12v LIGHT
D.C. is applied to both sides of the bulb, not because the circuit is broken.
* On water cooled engines the cooling fan is always live, the thermostat switch is
on the earth side. So a battery going flat could be caused by a faulty fan or fan
switch.
* The starter solenoid is always live so is a possible cause of a battery going flat
YELLOW
YELLOW
BROWN
WHITE
TESTS
GREY
RED
1. Stator Output.
Yellow to Yellow 27 - 31 v A.C.@ 2000 rpm. Unplug regulator.
Green - White 50 -150 ohm. Runner & Hexagon.(Stator un-plugged) A L C B G G
100 -160 ohm. Skipper & Typhoon.(Stator un-plugged)
Red - Brown 90 -140 ohm. All models. (Stator un-plugged)
2. Charging.
Between Red & Battery positive: >< 8.5 amps@ 2000 rpm with a fully
charged battery (13.5v) Choke
3. Battery voltage must be present at terminal "C" with ignition on or the output Control
from terminal B will be unregulated. Battery will boil, bulbs will blow etc. DC
MAIN FUSE: Rectifier
Runner (ZAPM07 / 08) 25 amp. Regulator
Out put only when
Hexagon (EXS1T & ZAPM05 / 06) 25 amp. charging
Typhoon (ZAPM02) 15 amp.
Skipper (CSM1T) 7.5 amp.
4
50cc 2t Ignition
Piaggio Ltd 19/07/02 Piaggio Ltd
This circuit could apply to any 50cc two stroke with or without a rev counter
IGNITION SWITCH
ON REV COUNTER
OFF
GREEN
COMMON EARTH
Champion NR2C FOR
NGK BR9ES INSTRUMENT PANNEL
GREEN
STATOR
GREEN
GREEN Ignition
Charging Coil
WHITE
WHITE
RED
RED
IGNITION PICK UP
TESTS
CDI / COIL 1. UNPLUG STATOR and CDI. GREEN WIRE SHOULD BE
CDI / COIL EARTHED WHEN IGNITION IS "OFF"
unit 2. CHECK CHARGING COIL.
unit GREEN TO WHITE = 980 ± 50 ohms.
3. CHECK TRIGGER COIL.
RED TO WHITE = 88 ± 5 ohms.
4. SPARK PLUG
NRG's are now supplied with Champion N1C plugs
The NGK equlivilent is B10ES.
This plug is very cold running and may not suit all riders.
If you find that a machine is fouling plugs try fitting an
NGK B9ES.
NOTES
3
NRG & ZIP Cat. Charging & Guages
Piaggio Ltd. 02/05/2003 8 pin regulator
YELLOW
2 3
7.5 amp
FUSE
BLUE
RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
FUEL GUAGE
OIL TANK
SENDER
FUEL
BROWN
BROWN
1
FUEL OIL
WARNING WARNING
LIGHT LIGHT
DC SERVICES
WHITE / VIOLET
WHITE / VIOLET
BLUE / RED
Brake light
Horn
WHITE / GREEN
WHITE
YELLOW / GREEN
FUEL
SENDER 5
UNIT
5 TO INDICATOR
SWITCH
4
AC
YELLOW / GREEN
SERVICES
WHITE / VIOLET
GREY / BLUE
Head light
BLUE / RED
Instruments
BLUE / BLACK
TESTS
1. Grey / Blue to earth = 25-30v AC YELLOW
stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC
1 2 3 4 5 6 7 8
stator and battery disconnected and engine at
2000 rpm.
3. Ammeter between red wire and battery positive
= 1.5-2 amp with fully charged battery and TIMER
1-2a
50 / 80cc 2T charging
Piaggio Ltd. 06/08/2002 8 pin regulator
YELLOW
2 7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION
SWITCH + BATTERY
WHITE 12v
BLUE
1
OIL
WARNING OIL TANK
LIGHT SENDER
DC SERVICES
Brake light
GREY / BLUE Horn
AC
SERVICES
Head light
GREY / BLUE
Tail light 4
WHITE
BLACK
Instruments
TO INDICATOR
BLUE / BLACK SWITCH
CHOKE UNIT GREY
NOT YELLOW
USED
1 2 3 4 5 6 7 8
OIL
LIGHT
TIMER
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the later 50cc and 80cc two stroke wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on for 15 seconds when ignition is turned on.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay and oil light check function.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter motor
but not the DC circuit or ignition circuit.
2
50 / 80cc 2T charging
Piaggio Ltd. 02/05/2003 5 pin regulator
BLUE BLUE 3
7.5 amp
RED FUSE
RED
ON
+ BATTERY
IGNITION
SWITCH OFF 12v
RED 12v 4ah - 50cc
12v 5ah - 80cc
WHITE
1
YELLOW
DC SERVICES
Brake light
Horn
GREY / BLUE
AC
SERVICES
Head light
Tail light
GREY / BLUE
Instruments
YELLOW
GREY
WHITE
BLACK
CHOKE UNIT GREY
A A G B+
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the early 50cc and 80cc two stroke wiring using a five pin connector on the rectifier /
regulator. Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on when the starter button is pressed.
* Two completely separate circuits for AC & DC.
AC is full wave and regulated
DC is half wave rectified and regulated
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
NOTES.
Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter motor
but not the DC circuit or ignition circuit.
1-1
PUREJET 50 IGNITION / CHARGE
Piaggio Ltd. 02/09/2003 GILERA RUNNER
BROWN
RED OFF
15 amp Champion
STATOR RG6YCA
RED
FUSE
BLUE
YELLOW 15 amp
YELLOW
YELLOW HT COIL
To starter
relay
BLUE
BATTERY +
BLACK / VIOLET
12v
BLUE
BLUE
BLACK / VIOLET
ORANGE
BROWN
BLUE
BLUE
RED
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
~ ~ ~ +
SYSTEM NOTES.
* 3 Phase AC.
* Permanent live battery feed to Rectifier, ECU, HT Coil (blue wire). Any of these could drain the battery if they were faulty.
* HT Coil is trigered by the BLACK / VIOLET wire being earthed via the ECU.
TESTS:
Stator: Disconected. Any yellow to any yellow = 0.7 - 0.9 ohm. Any yellow to earth = No continuity
Pick Up coil value is not quoted.
Rectifier / Regulator: With a charged battery the possible voltage must not exceed 15.2 volts.
1-9
ZIP 125 Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 NO Immobiliser
Ignition Green
Pick up ON Ignition
Power
OFF
Switch
to
LOCK services
G
ALTERNATOR
Orange
STATOR
Yellow
Orange
Choke Unit
WHITE / BLACK
ORANGE
Purple
PURPLE
To BLACK
2-10
Runner VX / VXR ignition / charging
Piaggio Ltd. 19/07/02 With IMMOBILISER
Green
Ignition Ignition ON
Pick up Power to
Switch OFF
services
Orange
G
ALTERNATOR
STATOR Red
Red
NGK 5
CR 8EB Green amp
Yellow Cooling
Fan Fan
Switch
Red / Blue
Choke Unit
White /
Rectifier / HT Coil Black
Regulator Green
p/n: 82501R
Black
Red Red
6 1 8 3 4 5 7 2 GREEN
WHITE / BLACK
RED / BLUE
Red / Blue
Purple RED
Headlight PURPLE
BLACK
via relay BLUE / BLACK
To YELLOW
Indicator Blue / Black
switch
Grey
/ Red Diagnostic
ECU / Immobiliser
Red / Blue socket Yellow
15
antenna
amp
LED on
Red 3 2 1 Yellow / Red instrument
8 7 6 5 4
pannel
Layout of pins Red
in the ECU / immobiliser
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
10ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-8
Hexagon GTX 125 ignition / charging
Piaggio Ltd. 13/03/02 With IMMOBILISER
Ignition Green
ON Ignition
Pick up
OFF Switch
Orange
G
ALTERNATOR Red
STATOR Red
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue White
Rectifier / HT Coil / Black
Regulator
p/n: 82501R
Black Green
Red Red
GREEN
6 1 8 3 4 5 7 2
WHITE / BLACK
5 3 21
antenna
amp 8 76 54
2-7
ET4 Leader engine ignition / charging
Piaggio Ltd. 13/03/02 With IMMOBILISER
Ignition Green
Pick up ON Ignition
Switch Power
OFF
to
services
Orange
G
ALTERNATOR
STATOR Red / Blue Carb. Heater
RG4HC
CR 9E
Yellow
Orange
Choke Unit
amp
via relay WHITE / BLACK
ORANGE
RED / BLUE
To Purple
Blue / PURPLE
Diagnostic
15 Red / Blue socket
ECU / Immobiliser
amp
3 21 antenna
8 76 54
Red Layout of pins Yellow LED on
in the ECU / immobiliser instrument
Red / Blue pannel
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
9ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-6
DNA 125 / 180 Switch Wiring
Refer to Service Station Manual
Piaggio Ltd. 08/05/2003 594329 (02/01) page 4-23>
1 2 3 4 5 6
ON
OFF
IGNITION SWITCH
LOCK ITEM 6 ON WIRING DIAGRAM
PARK
BLACK
GREEN
OFF
HIGH
LOW
0
SWITCHES
ITEM 8
ON WIRING DIAGRAM
BLACK
GREY - BLACK
YELLOW - BLACK
BROWN
PURPLE
WHITE ORANGE
WHITE - BLUE
BLUE - BLACK
PINK
EMERGENCY
LIGHTS START STOP
ALL PUSH RUN RIGHT HAND
SIDE 0 0
SWITCHES
OFF ITEM 9
ON WIRING DIAGRAM
WHITE
YELLOW - RED
GREEN - BLACK
WHITE - BLACK
ORANGE
BROWN
YELLOW
2-5
DNA Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 DNA 125 / 180
G
ALTERNATOR
STATOR
7.5 7.5
Green amp amp
Power to
Fan Cooling
Lights, horn
Switch Fan Orange
Yellow instruments
Orange
+ BATTERY
3 21
12v ECU
8 76 54
12ah
Black Blue / Red
White / Black Green
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm. YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY, LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-4
B 125 FUSE EXPLANATION
Piaggio Ltd. 08/05/2003 Piaggio Ltd.
WHITE / ORANGE
1 4 amp Engine start, run, warning lights
WHITE
WHITE / RED
12v DC from 2 4 amp Brake lights, start inhibit
ignition switch
RED / GREY
3 7.5amp Horn, Headlight flash
GREY
YELLOW
From light 4 4 amp Anologue, Inst. & side lights
switch
RED
12v DC from battery
5 6 7 8
4 10 15 15
a a a a
YELLOW BLUE
Headlight via relay Under seat, Light, Socket, Lock
2-3
B 125 / 200 NOTES
The notes should be used in conjunction with Service Station Manual 594845 and
the notes “B 125 ignition / charging” and “B 125 Fuse Explanation”
1. Seat has electric release. Only works when ignition switch is in the “off”
position.
If seat lock fails to operate:
Check fuse “7” in rear fuse box. 4 amp red wire in & blue wire out.
Check for power on Blue wire at ignition switch
Check for power on White / Blue wire at ignition switch with ignition “off”.
Check the push button, Blue / Black should earth when button is pressed.
Seat lock, power socket and under seat light are all controlled by the same
fuse.
3. Immobiliser is like other Leader engines. There are separate notes to explain
the immobiliser system.
5. Spark Plugs.
Please note that the correct spark plugs are:
125cc :- NGK CR8 EB p.n. 828866
200cc :- Champion RG6 YC p.n. 828708 (or NGK CR7EB)
2
B 125 / 200 ignition / charging
Piaggio Ltd. 13/08/2003 With IMMOBILISER
OFF
Blue
G
Ignition
Pick up White / Blue Blue / Black
White
White
Cooling
Fan Fan
Green Switch
Yellow Green
Red / Black
White
Ignition Relay
White RUN
STOP
CR 9EB White
Choke Unit White
White / Black
Red / Black
Red / Blue
Yellow / Blue
Blue
White / Green
15 15 4 Red / Black
15
Green Indicator
Black / Blue Switch
HT Coil
ECU / Immobiliser
Purple
3 21
Red Black 8 76 54
antenna
1 2 3 4 5 6
10 7.5 7.5 7.5 5 5
a a a a a a
RED / BLACK
12v DC from battery
BLUE
ORANGE ORANGE
Switched 12v Switched 12v
The wire colours shown here are different to those "on line" and in the owners hand
book.
The colours and fuse functions here are correct, they were checked on GT200
ZAPM312 * 2550.
FUSE:
1. 10 amp. Electric seat release. Headlights. Main beam warning light.
2. 7.5 amp. Intercom. Alarm. Immobiliser LED.
3. 7.5 amp. Intercom. Alarm. Water temp. Fuel warning & guage. Oil pressure warning.
4. 7.5 amp. Horn.
5. 5 amp. Stop light. start switch.
6. 5 amp. Side lights. Number plate light. Instrument panel lights.
MAIN FUSE.
A 15 amp fuse is located at the front of the under seat compartment.
2-14
Vespa GT 125 / 200 ignition / charging
Piaggio Ltd. 18/08/2003 With IMMOBILISER
G
ALTERNATOR Grey
STATOR
Red / Black
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow
Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue
Rectifier / Regulator White / Black
p/n: 82501R HT Coil
Green
Purple
Red / Black
GREEN
6 1 8 3 4 5 7 2
PURPLE
To BLACK
LED on
instrument
Main pannel ECU / Immobiliser
15
antenna 3 21
amp Red / Blue 8 76 54
Layout of pins
Red in the ECU / immobiliser
Note that the ECU fitted to the 125 and 200 have different characteristics.
They are NOT interchangeable.
+ BATTERY
TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12v GREEN TO BLACK (EARTH) = 105 - 124 ohm
12ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2 -13
LEADER Engine
Ignition immobiliser
For a full explanation of the immobiliser system please refer to the Service Station Manual.
The system is very similar to that used on the original Vespa ET4 but there are subtle
differences in operation, fault finding and component replacement. The CDI and immobiliser
are now combined in one box.
The vehicle is supplied with two keys. One MASTER key and one SERVICE key. Additional
service keys are obtainable but it is not possible to duplicate the master key.
TESTING.
Normally do not use the master key for testing.
Testing is done by using the instrument panel mounted LED.
If the system is working normally the LED will be flashing steadily when the ignition is
off and it will stop flashing when the ignition is on.
If the vehicle has not been used for 48 hours the light will stop flashing to save the
battery. It is restored by turning the ignition on and off.
If the immobiliser system is faulty, when the ignition is switched on there will be a series
of flashes. The flashes hold a key to the fault.
Turn on ignition;
1. The first flash will be long (2 seconds) or short (0.7 second). A Long flash means the
system is not programmed. A Short flash indicates that the system is programmed.
2. 2 second pause.
3. Next is a series of short (0.5 second) flashes. These define a fault.
1 flash = System is not programmed. Engine can run but only up to 2000 rpm.
2 flash = No key transponder detected. Fault with Key or antenna.
3 flash = Key transponder detected but not recognised. See the notes below.
4. The last thing to notice is whether the LED finally remains on or off.
OFF = Ignition is possible.
ON = Ignition is not possible.
Notes.
If the system is not programmed the LED indicator may not be flashing with ignition off
but it will perform the test function when the ignition is turned on.
Wrong key. There are a limited number of mechanical codes used for the keys. It is
possible that you could have two vehicles is stock that both have keys with the same
mechanical code. If you put the wrong key in the wrong vehicle it will turn on the ignition
but you will get the “transponder not recognised” fault code and the vehicle will not start.
12
1 of 2
Piaggio Ltd October 2001
Examples.
1 2 3
2 sec
System not programmed.
LED off Engine will only run to 2000rpm.
KEYS
The machine is supplied with two keys. One large brown MASTER key (with a flip out section
containing the chip) and One smaller SERVICE key.
The MASTER key should be kept safely at home. Only use it for programming.
The service key is the key that is used.
If you require a new service key this can be ordered from Fowlers and then programmed as follows:
A quicker easier alternative is to obtain a key from any automotive locksmith. The same system is
common on cars, most locksmiths will have the blanks and the equipment to identify the chip in your
key.
They will cut a key and then fit the correct type of chip into it. This chip will have been “cloned” from
your original so you will not need to programme this new key.
If both keys are lost the only solution is to replace the CDI unit and the locks. A new lock set comes
with a Master and a Service key.
12
2 of 2
Piaggio Ltd October 2001
LEADER ENGINE
Ignition, charging & immobiliser
Use these notes in conjunction with the SERVICE STATION MANUAL
The electrical system on the new Leader engine is very different to previous two stroke and
four stroke Piaggio engines. The ignition, charging & immobiliser circuits do not function in
the same way and do not share common components with previous versions.
Ignition is now using the battery circuit. Everything shares one common supply.
Alternator has three phase (all yellow wires) and ignition pick up coil (green wire) outputs
only.
Rectifier / Regulator is very simple. Three phase (yellow) inputs and one output.
CDI unit has become more complicated. The one unit is responsible for: ignition,
immobiliser, indicators & choke unit.
Much of the circuit is the same on ET4 Leader, Super Hexagon GTX 125, Liberty 125
Leader, Skipper ST, Runner VX / VXR and DNA 125 / 180, X9 125 but be careful
because there are differences. Early Skipper ST did not have an immobiliser, they do have
it now.
IGNITION.
When the ignition is turned on power is supplied to the CDI (terminal 5).
Ignition pick up is via green wire (terminal 2).
Output to the HT coil is via purple wire (terminal 3).
The unit is earthed via black wire (terminal 8).
CDI / IMMOBILISER
Note the CDI units have different part numbers for different models and engines size.
Refer to the diagram for each specific model. The wiring and wire colours may vary.
It is important that the correct part number is used as the ignition characteristics vary and
although the units look the same they are different!
HT COIL. 82597R = Common to most Leader engines. 82582R = Skipper ST & X9 125
Purple to Black - primary winding = 0.4 - 0.5 Ω
HT to Black - secondary winding = 3000 ± 300 Ω
Plugged in with engine cranking the peak voltage Purple to Earth = 100 vdc
11
1 of 2
Piaggio Ltd October 2001
IGNITION PICK UP COIL.
Un plug, check resistance, Green to Black = 105 - 124 Ω
Un-plugged with engine cranking the peak voltage Green to Black = 2 vdc
STATOR.
Any yellow to yellow should give continuity. Un-plugged, yellow to yellow = 0.7 - 0.9 Ω
Yellow to earth should not give continuity.
INDICATORS.
There is no separate indicator relay. The relay function is contained within the CDI unit,
Power to the indicator switch is via the blue / black wire (terminal 1).
If the indicators fail first check that you are getting voltage at terminal 1 (blue/black)
To check the switch and wiring. Unplug the CDI and link red/blue wire to blue/black wire,
when the turn switch is operated the appropriate lights should come on. (you will not need the
ignition to be turned on).
CHOKE UNIT.
The choke is now controlled by the CDI. (not the regulator).
Power is supplied to the choke via the main switched wire from the ignition switch to the
CDI. The unit will not function until the engine is running when the CDI will complete the
circuit to earth (terminal 7).
Un Plugged, resistance across the connections = >< 30 Ω @ 20˚C
Plunger extension. Measure how far the plunger protrudes from the body when it is cold,
this should be 12.5 - 13.0 mm. Now connect the choke unit to a 12v battery. The plunger
should have extended to 18.5 - 19.0 mm within 5 minutes.
Supply. Orange or Red / Blue to earth = Battery volts with ignition on.
Orange or Red / Blue to White/Black = 13-14.5v dc (system volts) with engine running.
11
2 of 2
Piaggio Ltd October 2001
X9 125 / 180 ignition / charging
Piaggio Ltd. 25/10/02 With IMMOBILISER
G
Fan
ALTERNATOR
Red / Black
STATOR Green
Fan Switch
Orange
Choke Unit
Yellow
Grey
/ Black
Lt. Blue Orange
RUN Emergency
STOP Stop
5
Side amp
UP
Stand
DOWN
Switch
Yellow / Green
Yellow / Blue
Rectifier / Red / White
Immobiliser Stand
Regulator LED Warning
p/n: 82501R
Red / Black
Power to 2 GREEN
Yellow 6 YELLOW
Lt. Blue
5 Lt. BLUE
2-9
50cc 4 stroke Charging / Ignition
Piaggio Ltd. 22/11/01 Piaggio Ltd.
STATOR
Test 2 Test 3
BROWN
Test 1
PICK UP SUPPLY TO
INDICATORS
BROWN
GREY / BLUE
1 2 3 4
GREEN INDICATORS
SWITCH
CDI / COIL
BLUE / BLACK
UNIT IGNITION SWITCH
ON
OFF
LOCK
CHAMPION
RG4HC
GREY / BLUE
RECTIFIER
BROWN WHITE WHITE REGULATOR
TO START RED BLACK
RELAY
10A FUSE WHITE GREY
SUPPLY TO
DC SERVICES
Test 4
BLACK
+ BATTERY AC SUPPLY YELLOW / BLACK
TO LIGHTS
12v
CHOKE HEATER
7ah GREY
LIGHTS
ON / OFF
SWITCH
GREY
Only two wires come from the stator. The engine to earth connection is very important.
Battery voltage at idle = 13 v (Battery charged) max will be 14.5 volts at high revs. Meter between battery neg. & pos.
Battery charge at idle = 1.5 - 2 amps (lights off). max will be >5 amps at high revs with all lights on. Meter between red wire and battery pos.
Test 1: Brown - earth = ~170 ohm To test pick up coil. Stator un-pluged
Test 2: Black - earth = ~1 ohm To test charging coils. Stator un-pluged
Test 3: Blue / Grey - earth = 25 - 35 v ac @ 2000 rpm with regulator disconnected. To test charging coils.
Test 4: White - Black = ~8 M ohm. If the resistance is low it could cause the fuse to blow.
10
This information is intended only for authorised Piaggio dealers.
50cc Four Stroke Restriction
Please refer to the notes about the legal implications of de-restricting a moped.
Piaggio do not advocate changing the restriction on any 50cc machine that may be used
on public roads.
Remember that if a Piaggio, Gilera or Vespa 50cc moped is de-restricted it will almost
certainly be technically illegal. It will not conform to Motorcycle legislation but it did
conform to Moped legislation.
The main restriction on the 50 cc four stroke engine is electronic. There is no restriction in the
exhaust pipe.
AC6+0000
38 mm
Cut here
Cut 3 mm deep
at 45º 60 mm
1. Make a 3mm deep cut with a hacksaw in the position shown. Then fill the slot with
silicon.
2. Remove the spacer washer between the front pulley halves.
3. Fit carburettor main jet size #78. Part number 969622
CUT
11
Piaggio Ltd.
X9 250 (Honda engine)
* At PDI
Set the clock TIME and DATE.
Set the TRIP to MILES.
Reset all three SERVICE LIGHTS.
* To change km to miles.
Insert ignition key.
Press and hold down “Trip” and “M” buttons
Turn on the ignition.
The display should now have changed.
* To test System.
With ignition off.
Press and hold down “clock” and “set” buttons
Turn on the ignition
All the systems will check them selves and all the lights should come on.
Any blown bulb or faulty system will be obvious.
* Stop lights.
There are a total of five stop light bulbs.
If two or more bulbs fail the warning light will come on.
* Hazard Lights.
Ignition on
Press hazard button, lights will start flashing.
Turn ignition off.
To stop the lights, first turn the ignition on then press the switch.
* Battery charging.
Charging at idle (1500 rpm) with the main beam on should be 2 amps.
8
1 of 4
Piaggio Ltd. 05/11/02
* Low fuel warning lamp.
The light will only come on when it has received a continuous signal from the sender for 13
seconds.
* Relays.
The vehicle has five relays.
Starter relay p/n 496403 has a 30 amp fuse and is in the battery compartment.
Start Permission relay p/n 292332 is in the battery compartment.
Two head light relays and the main power relay are all the same p/n 58002R they are all
under the front shield, headlights are central and the power relay is on the near side by the
indicator.
* Headlights.
The headlights are controlled by relays and each has it’s own relay so if the light fails and it
is not the bulb, check the relay.
* Choke unit.
Temperature sensor in the radiator can control the choke.
If the temperature drops to 0 degrees C then choke will come on (no voltage to the unit)
* Valve clearance.
Set Cold.
Engine at TDC.
Valve clearance is one division on the scale.
Correct level
* Gear Box Oil Level
Remove the level screw.
If no oil comes out top up until oil drips
then wait until oil stops before re-fitting
the bolt.
* Indicators
The indicator relay function is part of the digital display cluster. P/n. 581413. There is no
separate relay.
The wires involved are:
Blue / Black - right turn
Grey / Blue
Red / Black - left turn
Note that to operate the indicators the handlebar switch shorts the relevant wire to earth.
Hazard lights work by the switch earthing the brown wire from the digital cluster.
8
2 of 4
Piaggio Ltd. 05/11/02
* Braking system
1. Three brake disks are all the same size. 200mm diameter.
2. Both master cylinders are the same size.
3. All brake pads are the same. p.n. 494966
4. L/H front and rear calliper are the same and have 22mm pistons
5. R/H front calliper has 24mm pistons.
6. L/H front and rear are linked together in the following way
When left hand lever is used
Up to 8 bar pressure the rear brake only is operated.
8 - 23 bar both brakes are applied.
Over 23 bar the amount of pressure to the front brakes begins to decrease relative to the rear.
7. The R/H front calliper is operated by the R/H brake lever and has no connection to the other
brakes.
8
3 of 4
Piaggio Ltd. 05/11/02
X9 250 CHARGING & IGNITION
Refer to the X9 Charging & Ignition diagram.
* Note that sometimes the wires coming from a component change colour at the connector that joins
them to the wiring loom.
* See the separate sheet for an explanation of the fuses.
* Charging is three phase, fully rectified.
* Ignition is digitally mapped and can not be manually adjusted.
Spark advance will be affected by:
• Engine speed.
• Throttle position. See # 1
• Coolant temperature. See # 3
8
4 of 4
Piaggio Ltd. 05/11/02
X9 250 Charging & Ignition
Piaggio Ltd. 04/11/2002 Honda Engine
WHITE
RED / YELLOW HT COIL
MAIN POWER DPR7EA-9
FUSES IN
RELAY 15 7.5 7.5 10 FRONT
STORAGE 4
WHITE COMPARTMENT
WHITE / BLACK
RED /
IGNITION BLACK RED BLUE / YELLOW
SWITCH AUTO
2
CHOKE
BLACK
BLACK GREEN FUEL
DIGITAL
RED / RED / INSTRUMENTS THROTTLE PUMP
BLACK POSITION 5
BLACK
SENSOR
1 BLUE / YELLOW
7.5 10 10 20
FUSES IN RED / YELLOW
HELMET
COMPARTMENT
YELLOW / BLACK
RED
GREEN / BLACK
GREY / BLACK
YELLOW / WHITE
STARTER
STARTER MOTOR RADIATOR
RELAY 3 TEMP.
RED
RED / WHITE
BLACK RED
30 amp YELLOW / GREEN
START
RUN
PERMISSION
RELAY 9 ENGINE
RECTIFIER STOP
REGULATOR 10
RED /
GREEN /
BLACK
BLACK
WHITE / YELLOW
7 ORANGE / BLUE
WHITE / BLACK
YELLOW
6
+ BATTERY
12v
12 ah IGNITION
CONTROL
8 UNIT
YELLOW YELLOW
7
LIBERTY 125 Charging Circuit
RECTIFIER / REGULATOR WITH AN EIGHT PIN CONNECTOR
STATOR
Yellow
15 A FUSE
CHOKE White
UNIT Blue / Red + Battery
12v 9ah
Grey
White IGNITION
SWITCH
DC SERVICES
AC SERVICES BRAKE LIGHT
Red / HORN
HEAD LIGHT 7.5 A
Black TAIL LIGHT ETC.
CHOKE Fuse
CONTROL INSTRUMENT LIGHTS
RELAY To Indicator
switch
Blue /
Grey Grey / Blue White Black Black Yellow
1 2 3&4 5 6 7 8
Green / Not used
Black
DC RECTIFIER
AC &
12v DC REGULATOR REGULATOR
from
starter button
Rectifier / Regulator
P/N: 294878
6
Piaggio Ltd. April 1999
HEXAGON 250
Charging & Ignition Circuit
STATOR
White
12 volt 12 ah.
CHOKE
HEATER
Ignition
Ignition Switch
Pick up
15 AMP
MAIN FUSE
Red Red
Yellow
Black Blue / Red
Green Black
SERVICES
RECTIFIER / REGULATOR
Black
Yellow / Black
White / Green
Blue / Yellow
Blue / Red
Red / Black
Green
Black
Spark Plug
IGNITION NGK. DPR6EA-9
SWITCH
See Note
Yellow / Black
White / Green
Green
Black
Green / Yellow
White / Black
Contacts are:
Open to
run.
Green
Closed to
Pink
?
stop.
Fuel Pump
• Note that the wire colour sometimes changes from one side of a conector to the other.
• The choke supply is ><12 volts AC (only when the engine is running).
• The fuel pump senses the engine speed and varies the supply rate accordingly.
TESTING. Green – Black: No continuity with ignition switch and kill switch to Run.
Yellow - Yellow - Yellow: 0.1 – 1.0 Ώ. Stator winding.
Black/Red – Black: 50 – 350 Ώ. Ignition charging coil.
Green/White – Blue/Yellow: 50 – 170 Ώ. Ignition pick up coil
Yellow/Black – Black: 0.1 – 0.2 Ώ. HT coil primary winding.
HT – Black: 3.6 – 4.6 K Ώ. HT coil secondary winding.
5
Piaggio Ltd. March 1999
ET4 (original type) IGNITION IMMOBILISER.
General description
The ignition key contains an electronic digital code; this code must be recognised by the system before
the ignition system will function.
Thus the scooter has two forms of security – the key must physically operate the lock (in the normal way),
and the electronic code must be recognised by the system. In this way the scooter is safe against having
the ignition switch forced, or being hot-wired.
Main components
Decoder, which uses the antenna to read the electronic code of the key transponder.
CDI unit, which latches to the ON position only if an appropriate signal is received from the decoder.
Other components
7.5 amp fuse, which supplies +12V DC to the voltage stabiliser (located within the decoder box).
Voltage stabiliser (located within the decoder box), whose output (+12V DC) supplies power to the
decoder and the CDI unit via contacts in the ignition switch.
“Serial Line”, connects the decoder to the CDI unit, and conveys the authorising signal enabling the CDI
to latch to the “ON” position.
Normal Operation
The key grip contains a passive electronic transponder – a device that contains a unique pre-set digital
code, which can be read without direct electrical contact (similar to those used in the Datatag system).
The keys do not need any power and they do not contain a battery.
When the ignition switch is turned on, the decoder interrogates the key’s transponder.
Only if the decoder recognises the transponder’s electronic digital code will it send a signal via the serial
line to the CDI unit, enabling the otherwise conventional ignition system (alternator with pick-up and
charger coil, CDI unit and HT coil) to function.
However, the CDI unit and the decoder are also programmed to operate together as a matched pair; if
they detect a mismatch the CDI unit will not allow ignition.
4
Piaggio Ltd.
page1 of 6
To check the correct operation of the system
IT IS IMPORTANT THAT ON PDI AND AFTER ANY WORK ON THE IMMOBILSER SYSTEM, THE
CORRECT OPERATION OF THE SYSTEM IS CHECKED.
• Insert the red key with the hinged transponder in the flipped out position (this takes it out of radio
range of the antenna, thus enabling the system to be tested without the antenna automatically picking
up a code).
• Turn the ignition on and try to start the engine. IT SHOULD NOT START.
• Insert the blue key and try to start the engine. IT SHOULD START AND RUN NORMALLY.
Decoder and CDI units are initially manufactured as blank units. In this state (“Virgin”) and up to the time
they are programmed the immobiliser system will not offer any protection, and the ignition will function in
a conventional way. However, a “virgin” unit can be used as a substitute to aid in fault finding.
Programming functions can only be done with a red key. Once either the decoder or the CDI unit has
been programmed using a red key, they will only ever recognise that particular red key.
Therefore, it is vital that you USE ONLY THE BLUE KEY FOR ALL TESTING PURPOSES other than the
programming procedure itself.
If there is any fault with the system, the Immobiliser Test Box should be plugged in to the diagnostic test
socket. The test box (Part no 020319Y, Current dealer price £53.99 + VAT) is an invaluable, time saving
tool, and one which without doubt should be owned by all dealers.
Proceed as follows-
• With ignition off, turn on and wait for ‘On’ and ‘Pronto’ LEDs to illuminate.
• Turn ignition on. The ‘Seriale’ LED will flash, showing the signal on the Serial line.
• After a few seconds the appropriate LED will indicate the result of the diagnostic tests.
If the “No Serial line” LED lights up, it may be for the following reasons-
Serial Line circuit is broken.
Decoder is faulty
CDI unit is faulty
4
Piaggio Ltd.
page2 of 6
Diagnostic points to note-
To check for +12V DC power supply failure, check 7.5 amp fuse, and that +12V DC is present on
decoder terminals 3,5 and 8, and CDI unit terminal 1.
The CDI unit does not have its own earth lead, but is earthed to the alternator stator back-plate via the
white wire from terminal W. However, note also that back-plate and the engine itself is only earthed via
the electric starter motor lead. The decoder has its own earth lead.
There are two different types of transponder/decoder system; each type is not compatible with the other.
However this problem should only show up when trying to program new blue keys. In this case most
automotive locksmiths will be able to “clone” a new blue key if they are provide with a functioning red key.
These “cloned” keys will be recognised by the system without the need for programming.
CDI unit 1. Replace CDI unit (CDI can be replaced on its own).
2. Check for correct operation of system. Note that with a
virgin CDI unit the engine will start and run normally, but
the immobiliser system is inactive.
3. Program the CDI unit simply by turning on the ignition
switch using the red key
When programming keys do not have more than one transponder type key on the key ring, as the
decoder may pick-up both transponders.
4
Piaggio Ltd.
page3 of 6
VESPA ET4 IMMOBILIZER DIAGNOSTICS
When fault finding the ignition system on VESPA ET4, there is a very simple and quick check, which can
be done to give the Immobiliser the ‘all clear’. If you don’t have the effort-saving Immobiliser Tester (part
no. 020319Y) then insert a 12 Volt LED in the 2 pin socket (the blue/black lead is negative) located under
the helmet compartment and switch on the ignition whilst observing the LED. Note that the LED marked
Seriale on the Tester display shows this same signal.
It is advisable to get into the habit of using the blue key for all use and testing purposes other
than the programming procedure itself.
Normally-Functioning Immobiliser
The signal for a normally functioning Immobiliser system is a quick flash (0.7 seconds) and then the LED
remains off.
Immobilizer Fault-Finding
If the system is not functioning normally, it is recommended to obtain the Piaggio Immobiliser Tester. This
is by far the easiest way to diagnose faults. However, if for some reason this is not available, fault finding
can be done by observing the following.
2 secs 2 secs
LED off
0.5 secs
The above diagram shows the trace of the diagnostic signal for Decoder and CDI Units both
programmed, using a key with an unknown transponder (Table 2, case 5), resulting in 3 FLASHES during
the second phase of the diagnostic signal (Phase 2).
Phase 3: LED remains OFF if no fault is detected or ON if a fault is detected in the Immobilizer system
(the Tester does not consider a non-programmed CDI Unit a fault).
4
Piaggio Ltd.
page4 of 6
Table 1: Immobilizer Diagnosis Chart
Phase 2
LED Signal DIAGNOSIS
0 FLASHES NORMAL OPERATION
1 FLASH BREAK IN SERIAL LINE (ORANGE) OR DECODER EARTH (BLACK)
2 FLASHES NO TRANSPONDER DETECTED - FAULTY KEY OR IMMOB. ANTENNA
3 FLASHES TRANSPONDER DETECTED BUT NOT RECOGNISED BY IMMOB.
4 FLASHES VIRGIN DECODER AND PROGRAMMED CDI UNIT
KEY:
P = UNIT PROGRAMMED
V = VIRGIN i.e. UNPROGRAMMED
Y = ANTENNA FUNCTIONING
N = ANTENNA ABSENT or NOT FUNCTIONING
9 = IGNITION POSSIBLE
= IGNITION NOT POSSIBLE
PROG. = TRANSPONDER RECOGNISED THROUGH PROGRAMMING PROCEDURE
ANY = KEY WITH TRANSPONDER PRESENT BUT CODE DOESN’T MATTER
NOTES:
1. BLUE KEY - use for testing ignition after replacing Decoder and / or CDI Unit, otherwise you may
sacrifice perfectly good units; programs both Decoder and CDI Unit.
RED KEY - only use for programming operations and ONLY when you are sure the ignition system is
delivering a satisfactory spark.
The EXCEPTION to the above two points is when testing the Antenna with the RED KEY transponder
flipped out, as per the ET4 Service Station Manual.
2. LIMITED TO 2000 rpm
3. Normal operation with the either key
4. Break in the Serial line (orange lead) or Decoder not earthed properly (black lead)
4
Piaggio Ltd.
page5 of 6
4
Piaggio Ltd.
page6 of 6
Vespa ET4 (ZAPM04) charging circuit
From ZAPM04 * 51160 07/08/2002 8 pin regulator
YELLOW
2
7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
WHITE
ON
BLUE
OFF
GREEN
GREEN
BLACK WHITE
1
DC SERVICES
GREY / BLUE Brake light
Horn
WHITE
AC
GREY / BLUE
BLACK
Head light
TO INDICATOR
Tail light
WHITE / RED BLUE / BLACK SWITCH
Instruments
3&4 YELLOW
GREY
NOT
USED
1 2 3 4 5 6 7 8
RECTIFIER
REGULATOR &
REGULATOR
GREY
* This diagram shows the later (non Leader) ET4 wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* The charging system is basically the same as the 50cc & 80cc two stroke Sferoids.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay.
* The choke is supplied with 12v DC when the ignition is turned on but the circuit to earth is only completed
when the engine is running and 12v AC is supplied to the choke control relay.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
3
Vespa ET4 (ZAPM04) charging
Up to ZAP04 * 51159 07/08/2002 5 pin regulator
WHITE
CHOKE CONTROL
GREEN
WHITE
WHITE / RED
GREEN / BLACK
YELLOW GREY
+12v DC from
start button
AC SERVICES DC SERVICES
GREY / BLUE
1
YELLOW
WHITE
GREY
BLACK
RED
A A G B+
3
RECTIFIER BATTERY +
REGULATOR &
REGULATOR 12v
* This diagram shows the early ET4 (non Leader) wiring using a five pin connector on the rectifier / regulator.
Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* Three completely separate circuits for AC, DC & ignition.
AC is full wave and regulated
DC is half wave rectified and regulated
Ignition is the self powered CDI type typical on our two stroke scooters. Shorted to earth to stop.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is powered by the DC circuit but the relay to activate it is controled by the AC circuit.
Circuit will only be completed when both:
AC is present at relay terminal "B" and +12v DC is NOT present at the unmarked terminal.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
2
Coguar 125 Charging & Ignition
Piaggio Ltd. 07/08/2002 Honda XL125 engine
RECTIFIER / REGULATOR
PICK
UP
YELLOW YELLOW
STATOR
YELLOW YELLOW
YELLOW YELLOW
RED RED
GREEN BLACK
STAND
UP
SWITCH
FUSES STAND DOWN
1 X 20 AMP WARNING
1 X 15 AMP LIGHT DPR8 EA9
WHITE / GREEN
NEUTRAL
LIGHT NEUTRAL
SWITCH
STARTER
BUTTON
M CLUTCH
SWITCH
STARTER
RELAY
IGNITION
+ BATTERY UNIT
WHITE / GREEN
YELLOW / RED
12v BLUE
BLACK
WHITE / BLUE
NOTES
Three phase charging with inductive low voltage ignition.
The start & run permissive circuit is shown here in grey.
TESTS
Stator: Any yellow to any yellow = 0.8 ohm. Any yellow to earth should give NO continuity.
Regulated voltage: 14.0 - 14.8 volts with fully charged battery and lights on. Engine running at 5000 rpm.
1
X9 250 FUSE EXPLANATION
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
BLUE
1 20 amp Under seat light / Power socket
RED
WHITE / RED
12v direct from 2 10 amp Headlight relay
battery
RED / BLUE
3 10 amp Headlight relay
RED / BLACK
RED / BLACK
12v from battery 4 7.5 amp Digital Instruments
via start relay
1 2 3 4
15 7.5 7.5 10
a a a a
9
H@K & GSM Charging / Ignition
Piaggio Ltd. 23/04/02 Gilera engine
RED
WHITE
GREEN
ORANGE
RECTIFIER
REGULATOR BROWN
YELLOW
YELLOW
ORANGE
12v DC Services
FUSE
RED RED
IGNITION + BATTERY
SWITCH
12v
ON
OFF
R O G B
GREEN
RED
WHITE
ORANGE GREEN
GREEN RED
* Stator has separate coils for AC, DC and Ignition circuits. Champion N2C
Brown wire = supply for DC (battery circuit) NGK BR9ES
Yellow wire = supply for AC circuit
Green wire = supply for ignition
* Important that Stator has a good earth to engine and engine
must have good earth to chassis and battery.
* All Lights are powered by 12v AC
* Ignition is self generating and does not need the other electrical
circuits or the battery.
* Ignition is stopped by shorting the charge coil (green wire) to CDI / Coil
earth.
Check: Unplug Green wire from stator and CDI unit. You should
have continuity from green to earth with ignition OFF and no
continuity with ignition ON.
1
VESPA T5 HORN
Blue
HORN HORN SWITCH
NORMALLY ALTERNATOR
CLOSED
Yellow
Green
Black
REGULATOR
The T5 has a very simple 12 volt AC electrical system but one thing may not be clear
when you look at the wiring diagram.
It appears that the output from the alternator goes firstly through the horn, this does
not make much sense. If you are fault finding it is important that you understand how
the system works.
Explanation:
1. Out put from the alternator is the blue wire to the horn switch.
2. Horn switch is normally closed.
3. From there the yellow wire continues to the regulator.
4. Electricity always takes the easy path, so the current passes through the switch
rather than through the coil in the horn.
5. When the horn button is pressed and the circuit is broken and then the current will
have to pass through the horn and the horn will sound.
6. Power still reaches the regulator because the horn does not use all the power
available and it does not break the circuit.
7
Piaggio Ltd. October 1998
PX 125 / 200E Indicator Circuit
Piaggio Ltd. 06/08/2002 Piaggio Ltd.
NOTE.
The indicators flash alternatley; front - back (not both together)
This is to reduce the current needed
IDICATOR SWITCH
RIGHT
OFF
LEFT
PINK BLUE
BROWN WHITE
RED PURPLE
RED
WHITE / BLUE
PURPLE
WHITE
NOTE.
Turn Buzzer p/n 231284
could be connected to GREEN
INDICATOR
red / black or white if RELAY
required grey
red
blue
white / red
RED / BLACK
C B G G
WARNING
LIGHT ON
INSTRUMENT
PANEL
RED
RECTIFIER / REGULATOR
6
PX 200 / 125 Start Permissive circuit
Refer to Service Station Manual
Piaggio Ltd. 23/01/2003 578666 section 4
M BLACK PINK
Permissive switch
STARTER
MOTOR WHITE-RED
PINK
YELLOW GREY
ON IGNITION
WHITE
SWITCH Starter Protection
OFF
Relay
Located under
RED
WHITE horn cover
RED
RED
7.5 amp
FUSE + BATTERY
12v
RED
RED GREY
C B G G G
5
VESPA PX 125 / 200 Charging & Ignition
Piaggio Ltd. 04/07/02 Electronic Ignition
ON
DC OFF IGNITION
SWITCH
SERVICES YELLOW LOCK
GREEN
WHITE
RED
WHITE GREEN
RED
FUSE
+ BATTERY
7.5 12v
AMP
9ah
AC
RED GREY
SERVICES
RED / WHITE GREEN
C B G G
* AC output is regulated, full wave.
* DC output is regulated and half wave rectified.
* Alternator coils are connected in series.
REGULATOR
& * Ignition is self generating and totaly self contained.
DC RECTIFIER
REGULATOR
TESTS.
1. ALTERNATOR OUTPUT.
Unplug regulator. blue and earth = 26 - 30 vac @ 3000 rpm.
Unplug stator. red to white = 90 -140 ohms. green to white = 800 -1100 ohms.
2. BATTERY CHARGING.
Insert an ammeter betwen red wire and battery +.
With engine @ 3000 rpm and battery @ 13 vdc the ammeter should read 1.5 - 2 amps
* IN CASE OF OVER CHARGING.
un-plug the regulator and check that you have battery voltage on the red / white wire
that plugs into terminal "C". The regulator needs this input to function correctly.
* Check for good earthing between engine and chassis / battery / regulator.
4
H@K & GSM Notes
Modifying the exhaust.
Piaggio can not recommend de-restricting for any reason. Be aware that if a moped is
de-restricted then it becomes a 50cc motorcycle and should be re-registered. These
vehicles may not conform to the requirements to become a motorcycle.
Un-officialy and to save possible damaging experimentation the following information
is given.
Enlarge the hole in the end of the exhaust, where it plugs into the engine.
The end of the exhaust is a piece of mild steel bar with a small hole drilled through it,
this hole needs enlarging to about 18 - 20mm (3/4 inch).
The steel bar is case hardened to comply with “anti-tamper legislation”. To soften the
hardening; heat the end to bright cherry red and then let it cool naturally. Then you
should be able to drill it.
Re-jet with a #60 or 62 main jet. It is a standard DellOrto jet.
Engine To silencer
2
Piaggio Ltd. 22/12/00
Gilera RCR 50 Charging / Ignition
Piaggio Ltd. 09/09/2003 Derbi engine
LIGHTS
WHITE
ON
RED
OFF GREEN
RN2C
RED / BLACK
WHITE / RED
BR9 ES
BLUE
RED
CDI
and
HT COIL
GREEN / BLACK
4A FUSE
RED RED
OUTPUT
TO DC
SERVICES
+ BATTERY
12v
GREEN / BLACK
REGULATED
GREEN
OUTPUT
WHITE
RED
TO OUTPUT
INDICATOR TO AC
SWITCH SERVICES
YELLOW
RED / BLACK
ORANGE
YELLOW
RED
L + C YELLOW
G
GREEN
RED
WHITE
The Derbi electrics are arranged differently to Piaggio systems. Please study this carefully.
Earth wires are: YELLOW / GREEN.
Ignition is separate to AC & DC circuits. Ignition is shorted to earth to stop the engine.
STATOR OUTPUT. GREEN to EARTH = 610 ohms + 10% (CDI charging coil)
RED to EARTH = 80 ohms + 10% (Ignition pick up coil)
YELLOW to EARTH = 0.9 ohm + 10% (AC & DC circuit charging coil)
HT COIL secondary. 3.4 K Ohms + 15%. PLUG CAP. 5 K OHMS + 15%
4-8
X9 RANGE.
CHANGING THE ODDOMETER DISPLAY TO SHOW MILES
This should be done at PDI. See manual 594284. Pages 9-4 and 4-57
1. Press and hold the TRIP and M buttons.
2. Turn on the ignition.
3. Release the buttons
The display will now show “miles”.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights
will come on at the correct time. Service Station Manual 594284 4-61 and owners
hand books have details for setting the clock.
If when you briefly press the button the light that comes on is not the one before
the one you want to reset then briefly press the button again to make the light
scroll along.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the
digital instrument panel and Black is to earth.
1
PIAGGIO LTD 04/11/02
X9 UNDER THE FRONT PANEL
The front panel between the headlights is retained by five cross head screws.
Remove the panel to access the service light reset button and the two headlight
relays.
It is not necessary to remove the panel to adjust the headlight beam. The adjuster
screw can be accessed through the small grill near the top of the panel.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights
will come on at the correct time. Service Station Manual 594284 4-61 and owners
hand books have details for setting the clock.
RE-SETTING THE SERVICE LIGHTS
If one or more of the service lights is flashing follow this procedure:
1. Turn on the ignition. One of the three service lights is flashing.
2. Briefly press the button. The light before the one you want to reset should light.
3. Press and hold the button. The light you want to reset will start flashing faster.
While it is flashing fast release the button. Now the light should have gone out.
4. Turn off the ignition and turn back on to prove the light has been cancelled.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the digital
instrument panel and Black is to earth.
2
Piaggio Ltd. 04/11/02
Fuel Gauge & Sender Circuit
Piaggio Ltd 04/11/2002 Piaggio Ltd
Fuel Gauge
Low fuel
FUEL warning
A
C
B
WIRING
A = BLACK
Float B = GREEN / YELLOW
C = GREEN / WHITE
TESTS
A-C
Low fuel level >< 100 ohms
High fuel level >< 3 ohms
5
Piaggio, Vespa, Gilera
AUTOMATIC CHOKE OPERATION
The automatic choke units used on Piaggio scooters are all basically the same and all work in the
same way.
Remember that the choke defaults to being ON so it is unlikely that a cold starting problem is due
to a malfunctioning choke.
Operation.
• The choke unit has a plunger that is pushed down to close off a hole at the bottom of a drilling
in the carburettor.
• A wax pellet is heated electrically and expands, as it heats up it pushes out the plunger. As the
wax warms the electrical resistance measured across it increases until it becomes open circuit.
In most circumstances the choke will then remain off purely by the heat of the engine.
• The time taken for the choke to turn off is controlled only by the rate at which the wax expands.
The ambient temperature will affect the time taken for the choke to turn off. Cold weather will
mean the choke stays on longer etc.
• The choke is activated once the engine has started and not when the ignition is turned on.
50 & 80 cc two stroke engines.
These scooters have headlights that are run from 12 volts AC.
12 volts AC is used to operate the choke. AC can only be supplied when the engine is running so
the choke can not begin to turn off until the engine is running.
125 & 180 cc two stroke engines.
These engines have an all 12 volt DC system.
When the ignition is turned on there is 12 volts supplied to the choke but the circuit is not
completed to earth and no current can flow. So the choke will not turn off if the ignition is left on
before starting the engine.
When the engine starts the rectifier / regulator completes the circuit to earth (via the grey wire) and
the choke will turn off during the next few minutes.
125 four stroke engines. (not Leader)
Sfera 125 uses an AC system like the 50 / 80 cc engines.
ET4 employs a relay so that the choke will be powered by DC but is triggered by the AC supply
when the engine starts.
Leader four stroke engines.
These engines have an all 12 volt DC system.
When the ignition is turned on there is 12 volts supplied to the choke but the circuit is not
completed to earth and no current can flow. So the choke will not turn off if the ignition is left on
before starting the engine.
When the engine starts the CDI unit completes the circuit to earth (via the white / black wire) and
the choke will turn off during the next few minutes.
50 four stroke.
Connected to the AC output from the rectifier / regulator so power is only available when the
engine is running.
250 Hexagon & X9 250 (Honda engines).
AC powered by one of the three phase (yellow) wires direct from the generator.
4
1of 3
Piaggio Ltd. August 2002
Faults.
The most likely fault is the choke remaining ON. Symptoms will be anything that may be caused by
a rich mixture.
1. High fuel consumption.
2. Black spark plug.
3. Rough running when hot. OK when ridden hard but rough and four stroking at 20 mph.
4. Fails to start. Plug is found to be black and fouled.
Note. Remember that the choke defaults to being ON. If the choke does not turn off the symptom
will be a black and fouled plug. Or; The scooter starts and idles ok and runs at speed ok. When
riding slowly (15 - 20 mph) the engine runs very roughly.
4
2of 3
Piaggio Ltd. August 2002
Dia.2. Choke unit power supply.
Choke
DC powered choke
V 1. Ignition off = 0 volts
2. Ignition on = 12 volts
3. Engine run = 13-14.5 volts
Note. Choke units all look much the same but are different and it is important to use the correct
choke in the correct carburettor.
4
3of 3
Piaggio Ltd. August 2002
STATOR COIL VALUES
Refer to the relevant Service Station Manual / wiring diagram
Vehicle Ign. Pick Up Ign. Charging AC Circuit DC Circuit
50cc 2T Red - White Green - White Blue / Grey - Earth Yellow - Blue Red - Battery Positive
88 Ω (± 5 Ω) 970 Ω (± 50 Ω) 25 - 30v AC 25 - 30v AC 1.5 - 2 amp (charged bat.=13v)
Runner 125 Red - Brown Green - White n/a Yellow - Yellow
Hexagon 2T 90 - 140 Ω 50 - 150 Ω 27 - 30v AC
Liberty 125 Red - Brown Green - White Blue / Grey - Earth Yellow - Red Red - Battery Positive
ET4 original 100 - 130 Ω 300 - 400 Ω 25 - 30v AC 26 - 30v AC 1.5 - 2 amp (charged bat.=13v)
Skipper 2T Red - Brown Green - White n/a Yellow - Yellow
Typhoon 125 90 - 140 Ω 100 - 160 Ω 27 - 30v AC
Leader (all) Green - Black n/a n/a Any yellow - yellow 0.7 - 0.9 Ω
125 / 180 105 - 124 Ω Yellow to earth = no continuity
Hexagon 250 Green / White - Blue / Yellow n/a n/a Any yellow - yellow 0.1 - 1.0 Ω
GT & GTX 50 - 170 Ω Yellow to earth = no continuity
X9 250 White / Yellow - Yellow n/a n/a Any yellow - yellow >< 0.6 Ω
>< 200 Ω Yellow to earth = no continuity
X9 500 Engine speed & position sensor n/a n/a Any yellow - yellow 0.2 - 1.0 Ω
3
Test to be carried out with the stator un-plugged and engine stopped.
Test to be carried out with rectifier / regulator disconnected and engine running.
Test to be carried out with rectifier / regulator and battery disconnected.
Test with unit unplugged.
B (Beverly)
Clock and trip counter will re-set if voltage drops below 4,5v. Total distance record is “non-
volatile” and can not be affected.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold down the MODE and CLOCK buttons
3. Turn on the ignition
4. Miles or Km will be displayed to show which is selected. Turn off and start again to change it
DNA
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See manual 564329 page 4-42. The manual says that the change can
only be made if less than 6km show on the total distance. This is no longer true, the change can
be made as often as needed at any distance.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
ICE
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See manual 564811 page 4-13.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
X9
Clock.
The clock time and date functions MUST BE SET AT PDI. Because some of the service
light intervals are controlled by this.
6
1 of 2
Piaggio Ltd. 04/11/02
Service lights.
There are three lights on the display to remind the owner that certain servicing is due. These
lights are controlled by elapsed mileage and elapsed time so it is important to set the date
correctly at PDI. If you do not do this you may find the lights come on at the wrong time (and
you will get a grumpy customer).
OIL: Comes on after first 1000km (625 miles) and then after every 3000km
SERVICE: Comes on after first 1000km and then after every 6000km.
This light also comes on after one year even if the distance has not been covered.
BELT: Comes on after every 18000km.
Don’t forget to reset service lights when you do a service, even if they are not flashing
(scooter has come in early). If you do not do it the customer will be back in a few days with a
light flashing. That makes you look bad and again you have a grumpy customer.
It is probably worth going through the re-set procedure for all three lights at PDI because if
the battery had been connected previously the counter will have started from the wrong day.
ZIP
The Zip now has electronic instruments. The speedometer is still the traditional analogue
display but it is now electronically controlled. The odometer is now digital LCD. It is
supplied showing the distance in Km. It can be changed to show miles but only if it is
changed during the first 10km. CHANGE IT AT PDI.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold the button on top of the leg shield.
3. Turn on ignition. LCD display will show “Cont” (km) or “EnGL” (miles)
4. Briefly press button to toggle between the two alternatives.
5. When the correct press and hold the button for more than one second.
6. Turn ignition off. Turn back on to confirm the setting is now correct.
Re-setting the “Change Oil” warning.
At 6000km an oil change warning will be displayed on the LCD display for 10 seconds every
time the ignition is turned on. Cancel this at service.
1. Press and hold the button at top of the leg shield.
2. Turn on ignition on.
3. Release button and turn ignition off. Turn ignition back on to check that the warning has
been cancelled.
6
2 of 2
Piaggio Ltd. 04/11/02
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
Vacuum
tap
Vent
control
Balance pipe
Pump driven by crank valve
case depression Supply to
carburettor
Vent to
atmosphere
One way Pump
valve
Typhoon 80 and 125 have an auxiliary fuel tank located under the front panel. The
plumbing for this fuel system looks complicated. The Typhoon parts catalogue contains a
illustration which should help you locate the components on the vehicle. The diagram
above is intended to help explain the operation of the system and should prove useful when
fault finding.
VENT TO ATMOSPHERE The system has only one vent which you will find exiting under
the rear mudguard.
VENT CONTROL VALVE Controls venting to prevent loss of fuel from full tank. Air can
enter the tank without restriction but a slight pressure is required before vapour can exit.
AUX TANK VENT Auxiliary tank vents to the main tank via a pipe that has to run under the
foot boards. Because this pipe gets lower than the tank level it can become full of fuel and
so the auxiliary tank will not vent. To prevent this a limited flow ONE WAY VALVE allows
any fuel to be sucked out.
A large diameter BALANCE PIPE lets petrol flow between the two tanks.
A smaller diameter pipe passes through the PETROL PUMP which pumps petrol from the
auxiliary tank to the main tank.
Petrol PUMP is driven by the vacuum/pressure pulses from the crank case.
Note that the BALANCE PIPE stands up into the main tank so once the fuel level reaches
that point the pump will drain the auxiliary tank and all the remaining fuel will be in the main
tank. Because of this layout the fuel gauge does not drop at a steady linear rate. If you start
with a full tank, fuel is used in the following three phases:
1. Fuel used from main and auxiliary tanks equally - Gauge will drop from full to ¼ .
2. Level remains constant in main tank while auxiliary is drained - Gauge remains at ¼ .
3. Fuel is used only from main tank - Gauge drops from ¼ to empty.
VACUUM TAP is operated by vacuum from the inlet manifold.
1
1 of 2
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
FAULT FINDING
If you suspect that the fault is due to lack of fuel. Firstly prove that the carburettor is
running out of fuel.
Attach a piece of clear tube to the float bowl drain and turn it up the side of the
carburettor.
Open the drain screw. you will now be able to view the fuel level. It should remain about
3.5mm below the float bowl joint. If you find it is low or it drops during running then you
should explore the fuel supply.
If you have a problem that suggests a poor supply of fuel to the carburettor.
1. Check that you have fuel in the main tank. If you have fuel then you can forget about
the front tank and its associated plumbing, this can not affect the supply to the
carburettor.
Not able to get 7 litres of fuel in scooter with a nearly empty tank.
Auxiliary tank is not being used for some reason.
1. Check pump. With engine running you should see the pumped fuel coming out of the
pipe in the main tank.
2. Check for pinched pipes particularly under foot boards and helmet compartment.
3. Check auxiliary tank vent is clear of fuel (one way valve not working).
Scooter runs ok on bench but customer says it cuts out when ridden.
1. Pipe trapped under helmet compartment is squashed by weight of rider.
1
2 of 2
PUMPED FUEL SYSTEMS
Explanation of differences on Piaggio and Gilera scooters
DNA 50. ZAPC27 Hexagon 250 GT. ZAPM14 Runner VXR. ZAPM24
DNA 125. ZAPM26 Hexagon GTX 125 ZAPM20 Typhoon 80 TE81T
DNA 180. ZAPM26 Runner 50 ZAPC14 Typhoon 125 ZAPM02
Hexagon 125. EXS1T Runner FX. ZAPM07 X9 125. ZAPM23
Hexagon 125 LX. ZAPM05 Runner FXR ZAPM08 X9 250. ZAPM23
Hexagon 180 LXT. ZAPM06 Runner VX. ZAPM24 X9 500 ZAPM27
4
2 of 2
Piaggio Ltd. 04/11/02
HEXAGON EXS1T fuel system.
HEADER TANK
HEADER TANK
VENTING PIPE
MAIN TANK
CARBURETOR
FILTER
PUMP
CRANKCASE
3
Piaggio ltd. August 2001
DNA FUEL SYSTEM
Piaggio Ltd. 04/11/2002 PAGE 1 OF 2
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
VACUUM
TAP
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
2
DNA FUEL SYSTEM
Piaggio Ltd. 04/11/2002 PAGE 2 0F 2
MANIFOLD
VACUUM
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Early 50 NOTES:
1. Carburettor is gravity fed not pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
Later DNA 50
MANIFOLD
VACUUM
VACUUM TAP
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Later 50 NOTES:
1. Carburettor is pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
2
VESPA PX FUEL TAP
Piaggio Ltd. 07/08/2002 Piaggio Ltd.
CLOSED
OPEN
RESERVE
5
KEYS.
All Leader engined vehicles with immobilisers
Notes:
Only the Service key should be used day to day. The Master key should be kept
safely at home.
Use the Service key for testing and fault finding. Only use the Master key for
programming.
It is not possible to programme a replacement master key to a previously
programmed immobiliser.
It is possible to programme new Service keys only if you have the original Master
key.
Original Service keys with a chip fitted can be recognised by this symbol
etched into the metal near the top.
Keys Galore – London – 020 7586 9741 First Access – Herts - 0115 967 6466
Express Keys – Kent – 01689 850008 Auto Keys – London – 020 7586 9741
10
Piaggio Ltd. 04/11/02
GILERA TYRES & WHEELS
2000 / 2001 / 2002 / 2003
MODEL FRONT REAR
chassis prefix wheel tyre bar wheel tyre bar
Coguar 125 custom ZAPM17 2.50 x 17 100 / 80 - 17, 52 S T 1.8 3.00 x 17 130 / 70 - 17, 62 T T 2.0-2.2
DNA 125 / 180 ZAPM26 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 14 140 / 60 - 14, 64 P T/L 2.2– 2.5
DNA 50 ZAPC27 3.50 x 14 120 / 70 - 14, 55 L T/L 1.8 3.50 x 14 140 / 70 - 14, 62 T/L 2.0
GSM 50 super motard VTBC08 2.50 x 17 110 / 80 - 17, 52 T T 1.4 3.50 x 17 130 / 70 - 17, 62 T T 1.6
H@K 50 trail bike VTBC08 1.40 x 21 80 / 90 - 21, 48 P T 1.4 1.85 x 18 110 / 80 - 18, 58 P T 1.6
Nexus 500 (due August 2003) ZAPM35 3.50 x 15 120 / 70 - 15, 56 H T/L 2.2 4.50 x 14 160 / 60 - 14, 65H T/L 2.5
Ice 50 ZAPC30 3.00 x 10 120 / 90 - 10, 56 J T/L 1.3 3.00 x 10 120 / 90 - 10, 56 J T/l 1.8
RCR 50 trail bike VTHSDR1EB 80 / 90 - 21 T 1.0-1.1 110 / 80 - 18 1.2-1.3
Runner 50 all versions ZAPC14 / ZAPC362 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner 50 Purejet ZAPC361 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner FX125 / FXR180 (rear drum) ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner FX125 / FXR180 DD ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 13 130/60-13, 60 P T/L 1.6-2.2
Runner VX125 / VXR180 ZAPM24 3.50 x 12 120 / 70 - 12, 51 L T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner VXR200 ZAPM24 3.50 x 12 120 / 70 - 12, 51 P T/L 1.4 3.50 x 12 130 / 70 - 12, 56 P T/L 1.6-2.2
SMT 50 super motard VTHSDR1FB 110 / 80 - 17 T 1.7-1.8 130 / 70 - 17 2.0-2.1
8
STALKER 50 (previously SKP) ZAPC13 / ZAPC401 3.50 x 10 120 / 90 - 10, 56 J T/L 1.2 3.50 x 10 130 / 90 - 10, 61 J T/L 1.6-2.0
GFR 125 race replica 167 3.00 x 17 110 / 70 - 17, 54 T T/L 1.8 4.00 x 17 150 / 60 - 17, 65 T T/L 2.0-2.2
Nordwest 600 super motard 228 3.50 x 17 120 / 70 - 17, 60 R T/L 2.1 4.50 x 17 160 / 60 - 17, 60 R T/L 2.3-2.4
RC 600 trail 228 1.85 x 21 90 / 90 - 21, 54 T T 1.8 2.50 x 17 130 / 80 - 17, 65 T T 2.0-2.2
Saturno 350 & 500 café racer 222 3.00 x 17 110 / 70 - 17, 53 H T/L 2.1 4.00 x 17 160 / 60 - 17, 68 H T/L 2.3
XRT 350 / 600 trail 224 / 218 1.85 x 21 90 / 90 - 21, 54 T T 1.8 2.50 x 17 130 / 80 - 17, 65 T T 2.0-2.2
Chrono 125 race replica 164 2.50 x 16 100 / 80 ZR 16 T/L 1.8-2.0 3.00 x 17 130 / 70 ZR 17 T/L 2.0-2.2
Apache 125 trail 1.85 x 21 90 / 90 - 21, 54 R T 1.8 2.50 x 18 120 / 80 - 18, 62 R T 2.0-2.2
Freestyle 125 super motard 2.50 x 16 100 / 80 - 16, 50 S T/L 1.8-1.9 3.00 x 17 130 / 70 - 17, 62 S T/L 2.0-2.2
CX 125 race replica 158 3.50 x 17 120 x 60 ZR 17 T/L 2.1-2.2 4.00 x 17 150 / 60 ZR 17 T/L 2.3-2.4
Bold type denotes a current model. This list was last updated on 31 July 2003
Identify a vehicle by its chassis prefix AND model name.
Typhoon 125 ZAPM02 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 50 / Typhoon 50 RST TEC1T / ZAPC19 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 80 TE81T 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Velofax 50 VTAC02 1.60 x 17 70 / 90 - 17, 43M T/L 2.0 1.85 x 16 80 / 90 - 16, 46M T/L 2.5-3.0
Vespa ET2 50 two stroke ZAPC16 / ZAPC381 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 50 four stroke ZAPC26 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 125 four stroke ZAPM04 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 2.50 x 10 130 / 70 - 10, 62L T/L 1.8-2.0
Vespa ET4 Leader 125cc four stroke ZAPM19 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa PX125 VNX2T or ZAPM093 2.10 x 10 3.50 - 10, 51J T 1.25 2.10 x 10 3.50 - 10, 51J T 1.75-2.3
Vespa PX200 VSX1T / ZAPM18 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75-2.3
Vespa GT 125 / 200 ZAPM311 / 312 3.00 x 12 120 / 70 - 12, 51P T/L 1.8 3.00 x 12 130 / 70 - 12, 62P T/L 2.2
Vespa T5 Classic VNX5T 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75 - 2.3
X9 125 ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.1 3.50 x 14 140 / 60 – 14, 64 P T/L 2.3 – 2.5
X9 250 ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 13 140 / 60 - 13, 63P T/L 2.2 - 2.5
X9 500 ZAPM27 3.50 x 14 120 / 70 – 14, 55 S T/L 2.2 3.50 x 14 140 / 70 – 14, 68 S T/L 2.3 – 2.6
X9 500 fitted with dedicated top box 2.4 2.3 - 2.6
Zip 2000 Cat two stroke ZAPC25 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8 - 2.0
Zip 50 two stroke SSL1T 2.15 x 10 90 / 90 - 10, 50J T/L 1.2 2.15 x 10 90 / 90 - 10, 50J T/L 1.7 - 2.5
Zip RST 50 two stroke ZAPC06 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 100 / 80 - 10, 52J T/L 1.8
Zip SP 50 two stroke ZAPC11 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 110 / 80 - 10, 52J T/L 1.8
Zip 125 four stroke ZAPM25 2.50 x 10 100 / 80 - 10, 53L T/L 1.6 3.00 x 10 120 / 70 - 10, 54L T/L 2.0
Bold type denotes a current model. This list was last updated on 31 March 2003. Identify a vehicle by its chassis prefix AND model name.
Oil list
Vespa ET2 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Vespa ET4 50 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Vespa ET4 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Vespa ET4 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Vespa PX 125 2 str. Synthetic 2 stroke API TC or higher - 4 spd 80W GL4 or higher 250cc n/a - - sealed unit - Air -
Vespa PX 200 2 str. Synthetic 2 stroke API TC or higher - 4 spd 80W GL4 or higher 250cc n/a - - sealed unit - Air -
Piaggio B (Beverly) 125 / 200 4 str. 5W-40 synthetic API SJ or higher 1.1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio Deisis 100 2 str. Hi Scooter 2 Tech - CVT - Gear 80W-90 light gear GL3 or higher 110cc sealed unit - Air -
Piaggio Hexagon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon LX125 / LXT180 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GT 250 4 str. 20W-50 synthetic API SG or higher 800cc CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16 1.82 ltr.
Piaggio Hexagon GTX 125 / 180 (11") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GTX 125 / 180 (12") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio Liberty 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 30cc Air -
Piaggio Liberty 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 95cc 20W 90cc Air -
Piaggio Liberty 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Air -
Piaggio NRG 50 water cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16 900cc
Piaggio NRG 50 air cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Piaggio Skipper 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Piaggio Skipper ST 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Air -
Piaggio Typhoon 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Typhoon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio X9 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.2 ltr.
Piaggio X9 250 4 str. 20W-50 synthetic API SG or higher 1.1-1.3 CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Ethelyne Glycol Cuna NC 956-16
Piaggio X9 500 4 str. 5W-40 synthetic API SJ or higher 1.7 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.8 ltr.
Piaggio Zip 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 20W 25cc Air -
Piaggio Zip 50 4t 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 25cc Air -
Piaggio Zip 125 (single sided fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio Zip 125 (telescopic fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 60cc Air -
Gilera DNA 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera DNA 125 / 180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera GSM / H@K 50 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 500cc Chain - - ? ? Ethelyne Glycol Cuna NC 956-16
Gilera Coguar 125 4 str. 20W-50 synthetic API SG or higher 1.2 ltr. 5 spd. integral with engine - Chain - - 10W 280cc Air -
Gilera Ice 50 (front fork marked "TH") 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 72cc Air -
Gilera Ice 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 90cc Air -
Gilera Runner 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner FX125 / FXR180 (early) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner FX125 / FXR180 (late) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera Runner VX125 / VXR180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera SKP (Stalker) 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Gilera GFR 125 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 1.3 ltr. Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16
Gilera Saturno 350 / 500 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - ><7.5W 310cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera Nordwest 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera RC 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 640cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
SPARK PLUGS
PIAGGIO / VESPA mm NGK Champion
B 125 (Beverly) 125 (& 200) four stroke 0.7-0.8 CR8 EB RG4 HC
B 500 (Beverly) 500 four stroke 0.7-0.8 CR7 EKB RG6 YC
Cosa 125 , 150 0.6 B9 ES (BR9 ES) N2C (RN2C)
Cosa 200 0.6 B7 ES (BR7 ES) N4C (RN4C)
Free 50 (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon 125 &180 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon GT250 & GTX 250 (Honda 4 stroke) 0.8-0.9 DPR6 EA9
Hexagon GTX 125 four stroke 0.7-0.8 CR9 EB RG4 HC
Liberty 50 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Liberty 125 four stroke (original version) 0.7-0.8 CR9 E RG4 HC
Liberty 125 Leader four stroke 0.7-0.8 CR7 EB RG6 YC
Liberty 125 Leader four stroke (heavy use) 0.7-0.8 CR8 EB RG4 HC
NRG 50 water cooled (heavy use) 0.5-0.6 BR10 ES RN1C
NRG 50 (air or water cooled. All versions) 0.5-0.6 BR9 ES RN2C
Quartz 50 0.5-0.6 BR9 ES RN2C
Sfera 125 four stroke 0.5-0.6 CR9 E RG4 HC
Sfera 50 & Sfera 80 (all versions) 0.5-0.6 BR9 ES RN2C
Skipper ST 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Skipper 125 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Velofax 50 two stroke 0.5-0.6 BR9 ES RN2C
Vespa 50 Special & PK50S 0.6 B6 HS L86
Vespa ET2 50 two stroke (carburettor) 0.5-0.6 BR9 ES RN2C
Vespa ET4 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Vespa ET4 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Vespa GT 125 0.7-0.8 CR8 EB RG4 HC
Vespa GT 200 0.7-0.8 CR7 EB RG6 YC
Vespa Primavera ET3 0.6 B7 HS
Vespa Primavera & PK 125 0.6 B6 HS
Vespa PX 125 0.5-0.6 B7 HS L82C
Vespa PX 200 0.5-0.6 B7 ES (BR7 ES) N4C (RN4C)
Vespa T5 Classic 125 0.6 B9ES (BR9 ES) N2C (RN2C)
X9 125 (Piaggio 4 stroke engine) 0.7-0.8 CR8 EB RG4 HC
X9 250 (Honda 4 stroke engine) 0.8-0.9 DPR7 EA9
X9 500 (Piaggio 4 stroke engine) 0.7-0.8 CR7 EKB RG6 YC
Zip 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Zip 50 2 stroke (all versions, inc. catalytic) 0.6-0.7 BR9 ES RN2C
Zip 125 four stroke 0.7-0.8 CR7 EB RG6 YC
GILERA
Coguar 125 (Honda 4 stroke engine) 0.8-0.9 DPR8 EA9
DNA 125 & DNA 180 four stroke 0.7-0.8 CR8 EB
DNA 50 two stroke (catalytic) 0.6-0.7 BR9 ES RN2C
H@K & GSM 50 2 stroke (Gilera engine) 0.5-0.6 BR9 ES RN2C
H@K & GSM 50 2 stroke (Derbi engine) 0.-0.
ICE 50 two stroke catalytic 0.6-0.7 BR9 ES RN2C
Nexus 500 four stroke
Runner VX125 & VXR180 four stroke 0.7-0.8 CR8 EB
Runner 50, 125 & 180 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Runner 50 “Purejet” direct injection 2 stroke 0.6-0.7 RG6 YCA
SKP 50 two stroke 0.5-0.6 BR9 ES RN2C
OLDER GILERA MOTORCYCLES
Saturno 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Dakota 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Nordwest 600 four stroke 0.6-0.7 DPR9 EA9
RC 600 four stroke 0.6-0.7 DPR8 EA9
CX 125 & Apache & Crono & Free-Style 2 st 0.6-0.7 B10 EG - BR9 EG N82 - C55
GFR 125 two stroke 0.6-0.7 B10 EGV C55C
06/05/03
7-5
Up side down Forks
Piaggio Ltd. 07/08/2002 Typhoon / Runner etc.
Nylon Bush
Upper Circlip
Upper Circlip
Nylon Bush
Lower Circlip
Dust Seal
Tapered groove
Nylon Bush
Fork Leg
Lower Circlip
Fork Stanchion
Forks are grease filled for lubrication. The grease can be expected to work past the nylon bush so the chrome stanchion will get a
dirty ring round it.
Damping is by a sealed hydraulic damper cartridge in the left leg. The cartridge is held at the bottom by a bolt that will be found in the
bottom of the axle mounting. The top of the damper rod is held by a nut on top of the top yoke. If the seals in this unit fail you will find
oil dripping from the bottom of the left leg.
Some 50's did not have the damper. To check if a damper is fitted: look for the nut on top of the left leg, no nut means no damper.
To separate the fork leg:
1. Remove damper top nut (from left leg only).
2. Remove the dust seal.
3. Remove the bottom circlip.
4. Pulling the stanchion hard will force the upper circlip out of the tapered groove, the circlip and bush will be pulled out.
On very early forks the top circlip groove was not tapered so it will be necessary to pull the bush out to get to the circlip.
To pull the bush out:
1. Lubricate the bush with WD40 or similar.
2. Carefully screw two small self tapping screws into the nylon bush and pull it out using two pairs of pliers.
Note that there are several manufactures of these forks and although they look the same the internal components may not be
interchangeable between makes.
4
PISTONS AND SMALL END BEARINGS
Small End Bearing sizes.
Small end needle roller bearings fitted to two stroke twist and go engines and PX
engines are supplied in four sizes they are colour coded for identification.
The end of the con rod will either be colour coded or it will be marked with a
series of lines.
Piston sizes.
Piaggio use alloy or cast iron barrels on different engines. Alloy barrels can not
be re-bored and over size pistons are not available. Oversize pistons are
available for cast iron barrels. These are listed as 1M, 2M, 3M.
In addition to oversize there will be four pistons listed for all engines as “FC” or
FC1, FC2 etc. These are tolerance fittings.
Pistons can be matched to barrels in two ways. Either by referring to the
tolerance data page near the front of the appropriate Service Station Manual or
by referring to the marking on the crown of the piston and the top of the barrel.
On some engines barrel and piston will both have a letter stamped into them.
Both letters should match. The lowest (first) part number will be the smallest piston
and first in this list.
Remember, if you are measuring barrel and piston you should always measure in
line with the gudgeon pin because they will have worn oval. Most wear occurs
at right angles to the gudgeon pin.
3
Piaggio Ltd. August 2001
PX 200 / 125 “COSA” TYPE CLUTCH
The COSA type clutch is now fitted to the PX 200 & PX125.
It can replace the old type clutch as a complete assembly. p/n 433548 (200cc) p/n 288650 (125cc)
NOTE
CHAMFER
Piaggio Ltd. May 2000
FITTING NEW MAIN BEARINGS TO TWO STROKE AUTO’S
Replacing the main bearings is not a difficult job but it MUST be done the correct
way to ensure a correct fit.
The problem can be that you do not achieve the correct end float in the crank so
the bearings are being side loaded. This will cause a bearing failure within a very
short time (200 miles max!)
It is vital that the end float is checked with a dial gauge once the cases have
been bolted together.
The following assembly procedure is the ONLY way to do the job. It is the quickest
and easiest. Also it almost guarantees correct tolerance. Please do it this way:
1. Heat the bearings in engine oil. First signs of smoke from the oil is hot enough!
About 100 degrees
2. Support the crankshaft vertically. Drop one bearing onto crank. If it will not drop
on (by gravity) it is not hot enough. If you have to tap it home, ONLY use a
piece of tube to act on the centre race. NEVER hit the outer race. Once it is on
leave it to cool.
3. Turn crank over and drop other bearing on. Leave it to cool completely.
4. Position the drive side crankcase half on its side with inside facing up. Support it
on blocks of wood so the crank can be dropped in (again, just using gravity).
1
1 of 4
Piaggio Ltd. 10/03/03
5. Hear the case with a hot air gun, mostly heat it around the area where the
bearing will fit. Don't try to hurry this. It is hot enough when the rear end of the
case is too hot to keep you hand on.
6. When it is hot enough then drop the crank / bearing in and leave it to cool. If it
will not drop in easily then the case is not hot enough yet.
7. Once it is completely cold turn the case over so the crank is hanging down and
then fit the crank removal tool 20163Y (50cc) or 20262Y (125 & 180cc) as if you
were going to press the crank back out of the case.
8. Tighten the extractor bolt as tight as you can by hand. This will push the crank
out against the bearing so all the free play in the bearing has been removed
and the crank is pushed out as far as it can go. Do not use a spanner to tighten
the bolt or you may move the bearing. Tightening it by hand can not move the
bearing (you ain't that strong).
2 of 4
Piaggio Ltd. 10/03/03
9. Now position the other crank case half on the blocks of wood (inside facing up)
heat it as before and drop the crank / crank case onto it.
10. Fit the cases together with liquid gasket (not silicon). Don't forget the water
pump impeller on water cooled engines. Bolt it up and leave it to cool.
11. Once it is completely cold remove the special tool. Now use a dial gauge to
measure the end float. Pull the crank one way, notice the gauge reading and
then push it the other way. You MUST have 0.03 - 0.09mm free play.
12. If you have nearly got the free play try hitting each end of the crank with a
nylon hammer and check again.
13. If you have not got enough free play there is no point carrying on. Take it apart
and do it again (I would recommend using new bearings just in case the others
have been damaged!).
The reason for establishing the end float is to ensure that there is no side load on
the bearings. Ball races do not like side load and they will fail very quickly.
Checking the free play guarantees that the bearing is not side loaded and the
balls can run centrally in the bearing tracks.
Please do not try and improvise. Make sure you have all the correct tools for the
job. They are a very good investment for time saved and stress avoided.
If you have any questions please give your Regional After Sales Manager a call.
3
3 of 4
Piaggio Ltd. 10/03/03
Section through
Main bearing
1. The top diagram shows a bearing correctly fitted with no side load.
Only the whole load is being transmitted through the balls.
2. The lower diagram shows a bearing that has a side load. The inner and outer
tracks are being pushed in opposite directions.
The balls are now transmitting the load at an angle and the side force has the
effect of forcing the balls up a ramp (the shape of the track). The balls are
trying to push the inner and outer tracks apart. Because of the ramp effect the
force applied is far higher than just the side loading. So now the tracks are
being subjected to not only the normal load but also another huge load.
In addition the extra load may force the lubrication away from the point of
contact so you will have a dry metal to metal contact rather than a film of oil
separating the parts.
4
4 of 4
Piaggio Ltd. 10/03/03
FITTING NEW MAIN BEARINGS TO TWO STROKE AUTO’S
The problem can be that you do not achieve the correct end float in the crank so
the bearings are being side loaded. This will cause a bearing failure within a very
short time (200 miles max!)
It is vital that the end float is checked with a dial gauge once the cases have
been bolted together.
1. Heat the bearings in engine oil. First signs of smoke from the oil is hot enough!
2. Drop one bearing onto crank. If it will not drop on (by gravity) it is not hot
enough. Once it is on leave it to cool.
3. Turn crank over and drop other bearing on. Leave it to cool completely.
4. Position drive side crank case half on its side with inside facing up. Support it on
blocks of wood so the crank can be dropped in (again, just using gravity).
5. Hear the case with a hot air gun, mostly heat it around the area where the
bearing will fit. Don't try to hurry this. It is hot enough when the rear end of the
case is to hot to keep you hand on.
6. When it is hot enough then drop the crank / bearing in and leave it to cool.
7. Once it is completely cold fit the crank removal tool 20163Y (50cc) or 20262Y
(125 & 180cc) as if you were going to press the crank back out of the case.
8. Tighten the extractor bolt as tight as you can by hand. This will push the crank
out against the bearing so all the free play in the bearing has been removed
and the crank is pushed out as far as it can go. Do not use a spanner to tighten
the bolt or you may move the bearing. Tightening it by hand can not move the
bearing (you ain't that strong).
9. Now position the other crank case half on the blocks of wood (inside facing up)
heat it as before and drop the crank / crank case onto it.
10. Fit the cases together with liquid gasket (not silicon). Don't forget the water
pump impeller. Bolt it up and leave it to cool.
11. Once it is completely cold remove the special tool. Now use a dial gauge to
measure the end float. Pull the crank one way, notice the gauge reading and
then push it the other way. You MUST have 0.03 - 0.09mm free play.
12. If you have nearly got the free play try hitting each end of the crank with a
nylon hammer and check again.
13. If you have not got enough free play there is no point carrying on. Take it apart
and do it again (using new bearings!).
The reason for doing this is to ensure that there is no side load on the bearings. Ball
races do not like side load and they will fail very quickly.
Checking the free play guarantees that the bearing is not side loaded and the
balls can run centrally in the bearing tracks.
If you have any questions please give your After Sales Representative a call.
1
1 of 2
Piaggio Ltd. 04/11/02
Section through
Main bearing
1. The top diagram shows a bearing correctly fitted with no side load.
Only the whole load is being transmitted through the balls.
2. The lower diagram shows a bearing that has a side load. The inner and outer
tracks are being pushed in opposite directions.
The balls are now transmitting the load at an angle and the side force has the
effect of forcing the balls up a ramp (the shape of the track). The balls are
trying to push the inner and outer tracks apart. Because of the ramp effect the
force applied is far higher than just the side loading. So now the tracks are
being subjected to not only the normal load but also another huge load.
In addition the extra load may force the lubrication away from the point of
contact so you will have a dry metal to metal contact rather than a film of oil
separating the parts.
1
2 of 2
Piaggio Ltd. 04/11/02
SERVICE LIMITS
NEW LIMIT Or change at:
50cc 2T
(Inc. Purejet) Belt - 17.5mm 15,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 20,000 km
50cc 4T
Oil 850cc 6000 km
Belt - 17.5mm 12,000 km
Rollers 18.9mm 18.5mm -
125cc 2T
Belt - 21.0mm 12,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 30,000 km
125cc 4T orig.
Oil 850cc 5000 km
Belt 17.2mm 10,000 km
Rollers 18.5mm -
125cc 4T Leader.
Oil 1 ltr. 6000 km
Belt 22.5mm 21.5mm 12000 km
Rollers 19.0mm 18.5mm -
B 125 Brake Disks 4.00mm 3.50mm -
180cc 2T
Belt - 20.5mm 12,000 km
Rollers - 19.5mm -
Oil Pump Belt - - 30,000 km
180cc 4T Leader.
Oil 1 ltr. 6000 km
Belt 20.5mm 19.5mm 12000 km
Rollers 20.6mm 20.0mm -
250cc 4T Hex
Oil 800cc 3000 km
Belt 21mm 18000 km
Rollers 23.8mm 23.2mm -
250cc 4T X9
Oil 1 ltr. 3000 km
Belt 23.3 22.3 18000 km
Rollers >< 23mm 22.5mm -
500cc X9
Oil 1.7 ltr. 6000 km
Belt 26.2mm 25mm 12000 km
Rollers 24.9mm 24.5mm Check 12000 km
Front Disk 4.00mm 3.50mm -
Rear Disk 5.00mm 4.50mm -
15
Piaggio Ltd. 04/03/03
QUICK REFERENCE GUIDE
FIRST SERVICE is always at 1000 km (625 miles)
Older engines used variator rollers that needed greasing. Later greasless rollers can be fitted
to early variators. If greased rollers are used lubricate sparingly at every service (except
first): Use only “Jota” grease p.n. 494643
125 4t. (Original) air cooled GT 250 / GTX 250 (Honda Helix)
Check oil level by sight glass. Check oil level with dipstick screwed OUT
Engine Oil: 10w40 synthetic. 850 cc. Engine Oil: 800cc (1ltr after strip) 10w40
Oil Change: 3000 km Oil change: 3000 km
Service: 6000 km. Service: 6000 km
Rear Hub: 80w Light Gear. 90 cc. Rear Hub: 150cc 10w40
Fuel: Min 95. Unleaded. Coolant: 1.82 ltr.
Tappets: 0.15 mm. 50/50 with distilled water
Ign. Timing: 10° @ 1500. 32° @ 6000 rpm. Tappets: Back off one division
Idle: 1600 – 1800 rpm Ign. Timing: 12° @ 1500. 27° @ 7000 rpm
Slow running: 3.5 turns out. (out to richen) Idle: 1500 rpm.
CO: 3.5% (hose on exhaust outlet) Slow running: 2 ¾ turns out (out to richen)
Spark Plug: 0.7 - 0.8 mm CO: not quoted
Champion RG4HC Spark Plug: 0.8 - 0.9mm
NGK CR8E (colder) NGK DPR6EA9
Rollers wear limit: 18.5 mm min. dia. Pulley wear limit: 0.4mm
Belt wear limit: 17.2mm (min width) Belt wear limit: 21mm (min width)
Change Belt: 10,000 km (24 mths) Belt Change: 12,000 km (24 mths)
14
2 of 3 Piaggio Ltd. 04/03/03
125 4t Coguar. Honda XL125 engine 100 2t. Diesis. Derbi engine
Check oil level with dipstick screwed out. Service: 5000 km (12 mths)
Engine Oil: 1.2 ltr. 20w50 synthetic SG Hub Oil: 110cc - 80w90 light gear oil
Oil change: 3000 km Spark Plug: 0.6 - 0.7 mm
Service: 6000 km Champion RN2C
Tappets: in:0.10 mm. ex: 0.10 mm NGK BR9 ES
Ign. Timing: 15° @ 1400. 32° @ 3450 Belt change: min width = 16mm
Idle: 1400 rpm. 5000 km (12 mths)
Slow running: 2 turns out (out to richen) Then every 10,000 km
CO: 5% + 0.5%
Spark Plug: 0.8 - 0.9 mm 500 4t Master
NGK DPR8 EA9
Check oil level with dipstick screwed IN
Chain size:
Engine Oil: 1.7 ltr 5w40 synthetic SJ
Oil change: 6000 km (check @ 3000 km)
50 2t H@K, GSM. Gilera engine Service: 6000 km (12mths)
Service: 5000 km (12 mths) Rear Hub: 250cc 80/90 light gear oil.
Gearbox Oil: 500cc - 10w40 4t engine oil Coolant: 1.8 ltr. 50 / 50 mix
Spark Plug: 0.5 - 0.6 mm Tappets: in: 0.15mm. ex: 0.15 mm
Champion RN2C Idle: 1450 rpm. + 50 rpm.
NGK BR9 ES CO: 1.25% + 0.25%
Chain size: 415 x 124 links CO2: 14.5% + 1%
Spark Plug: 0.7 - 0.8mm
Champion: RG6YC
50 2t PUREJET. Direct injection NGK: CR7 EKB
Service: 5000 km (12mths) Rollers wear limit: 24.5 mm min.dia.
Hub Oil: 75cc - 80w90 light gear oil Belt wear limit: 25 mm width.
Spark Plug: 0.5 - 0.6 mm Belt Change: 12,000 km or 24 mth.
Champion RG6 YCA Air Filter Change: 18,000 km or 36 mth.
NGK ? Fuel Filter Change: 48,000 km
Belt width: 17.5 mm min width
Belt change: 15,000 km (36mths)
Rollers: 18.5 mm min.dia.
Fuel Filter: 10,000 km (24 mths)
Mixer belt: 20,000 km
If there is ever any doubt about service intervals for a vehicle, always use the intervals shown in
the owners handbook.
Piaggio recommend fully synthetic oil for all engine applications.
Piaggio have never offered any tuning parts for any vehicles and we will never recommend
tuning or de-restricting a vehicle for any reason.
All 50cc vehicles are only available as “mopeds” restricted to 30mph.
All current 125cc vehicles are “Learner Legal” producing less than 15 hp (11kw). They are not
restricted If they are tuned they will not be learner legal and warranty will be affected.
14
3 of 3 Piaggio Ltd. 04/03/03
PIAGGIO / VESPA / GILERA
CHASSIS NUMBER LOCATION.
Ice 50
Remove the black central cover over the oil tank filler. The Chassis number is
stamped into the main chassis tube on the off side just below the oil filler cap.
Liberty, Free
Chassis number is stamped onto a plate attached to the frame on the off side
above the cooling fan cover.
Velofax
Chassis number is stamped into the underside of the rear carrier (part of the
frame).
X9 125, 180, 250 & 500. B (Beverly) 125, 200 & 500
Lift seat. Pull up the internal carpet at the rear. Remove the small panel in the
floor toward the rear. Chassis number is directly below.
DNA, H@K, GSM and older Gilera motorcycles, Nordwest, RC600, GFR etc.
The chassis number is stamped into the right hand side (off side) of the head
stock.
A duplicate of the chassis number will not be found in any other location. If the
number has been removed it will not be possible to identify the vehicle.
Most vehicles now have a specification sticker, which is most likely to be under the
seat. Along with the Homologation and specification details you should find the
chassis number. This metallic sticker is often removed or lost.
13
Piaggio Ltd. November 2002
Restriction Notes
Never discuss the technicalities of how to de-restrict with end users. But, advice given can
prevent problems caused by them fiddling blindly.
Piaggio have never supplied any information about how vehicles are restricted or how to make
them go faster.
Piaggio can not advocate de-restriction for any reason.
Vehicles will only have been homologated as Mopeds so will be technically illegal if they are
de-restricted.
Piaggio have never offered any tuning parts.
If a 50 is de-restricted the licensing requirements will be the same as a 125, so Piaggio’s official
line is “Do not de-restrict, if you want to go faster get a 125”
125cc engines are not restricted, they are designed to produce no more than 11 kw. So they will be
learner legal.
50cc engines are always restricted and are only sold as 50 km/h mopeds. There is no “full power”
option. Most countries in Europe have the same 50 km/h category.
Restriction of 50cc 2 stroke geared engines. H@K & GSM. See Chapter 4 page 2
Only restriction is a restrictor in the inlet end of the exhaust pipe.
A two size larger main jet will be needed. A standard DellOrto part.
If de-restriction is carried out by an authorised dealer, Piaggio are happy that the warranty will not
be affected. Any tuning or fitting of after market parts by the end user or the dealer will affect the
warranty.
12
1 of 2
50cc Moped restriction information
What is a moped?
A Moped is a two wheel vehicle of no more than 50cc with a design top speed of 30 mph (on the
flat).
All current Piaggio, Vespa and Gilera 50cc two-wheel vehicles are restricted and are only supplied
as Moped’s. They are only tested and homologated as mopeds.
Piaggio do not recommend de-restricting or modifying for any reason.
If the vehicle may be used on a public road. The person carrying out the modification must take full
responsibility for the possible implications of their actions.
If a Moped is de-restricted.
1. It becomes a 50cc Motorcycle.
DVLA should be informed and the vehicle re-registered.
2. It may not conform to motorcycle requirements and may not be legal.
For example; Lighting requirements are different for Mopeds and Motorcycles.
Piaggio can not give any assurance that a de-restricted vehicle will be technically legal.
3. A motorcycle licence will be required.
A 50cc motorcycle has the same licence requirement as a 125cc.
A Motorcycle can not be ridden on a provisional motorcycle licence before basic training is
completed (CBT).
A full car licence allows a moped to be ridden but not a 50cc motorcycle.
4. A rider must be at least 17 years old.
A 16 year old can ride a Moped but not a 50cc Motorcycle.
5. The Insurance company who are insuring the vehicle should be informed.
The premium will probably be un-affected but any modification should be notified to the
insurer in writing. Insurance will be invalid if the vehicle is modified and the insurer not
informed.
Remember that if the vehicle or the rider is not legal then the insurance will be invalid.
6. Piaggio Ltd. Are happy that the warranty will remain valid if the de-restriction is carried out by
an authorised dealer.
If any “tuning” or fitting of non Piaggio parts is carried out then the warranty will be invalid.
Piaggio’s advice has to be: If you want to go faster, get a 125.
Recently a 16 year old was stopped for speeding, when the Police realised his age they immediately
charged him with.
1. Exceeding the speed limit.
2. Riding a motorcycle with no motorcycle licence (he was under age).
3. Riding a motorcycle without valid insurance.
The dealer who did the de-restriction was charged and found guilty of aiding and abetting!
The boy’s father attempted to sue the dealer!
A disclaimer may be of little use as a defence. Be warned! If someone rides to your shop and asks
you to de-restrict then rides away they will be breaking the law and they have only been able to
break the law because you helped them.
If you get a disclaimer signed one of the conditions should be “I do not intend to use this vehicle on
public roads” and another should be “I am fully aware of the legal implications of having my
vehicle de-restricted and I am prepared to take full responsibility for this”.
12
2 of 2
ALARM CONNECTION
ADAPTERS ALARMS
Connector 445143
OLD only Hexagon # EXS1T
SWITCH
445152 445149 = Fido 2
Not ET4 / PX / EXS1T (600171M)
600712 M Replacement key = contact Piaggio Ltd
Additional adapter {
445150 = Fido 2
602095 M Battery backup
Not ET4 / PX / EXS1T Replacement key = contact Piaggio Ltd
No adapter needed
only DNA 50, 125, 180 600447 M000E
Mini - Full
Supplied with one key
602097 M Spare key = 602092M
Not ET4 / Leader / PX
/ EXS1T
Connector
600897M
SWITCH only ET4 (not Leader) 602154 M00E
1999 > Mini - Self Powered
Supplied with two keys
(not used on PX) 602169M00E Spare key = 602092M
Not ET4 / Leader / PX
/ EXS1T
The new LEADER engine has a very different electrical system and an adapter for this is not
available yet. Do not try to use any existing adapter.
{ The additional adapter 600712M is used to convert the old style harness so it can be plugged into
the new style ignition switch.
11
1 of 2 Piaggio Ltd. 04/11/02
Alarm Information
There are four alarms supplied by Piaggio:
Fido: suitable for Vespa PX
Fido 2: Needs a wiring adapter to connect it to the vehicle wiring. Suitable for many of the older
models. Check the fitting list for compatibility.
Mini Full: More compact unit. Needs a wiring adapter. Suitable for many models.
Check the fitting list for compatibility. Mini Full will plug directly into the DNA wiring harness.
Mini Full Self Powered: Similar to Mini Full but with battery back up. The wiring socket is
different to the Mini Full and it requires specific wiring adapters. Check the fitting list for
compatibility.
Wiring adapters are not currently available for Leader engines. Leader engined vehicles are
supplied with an immobiliser as standard. Except the DNA which has a socket to allow the Mini
Full to be plugged into it directly.
Programming new keys for Mini Full and Mini Full Self Powered alarms.
Additional keys can be obtained from Fowlers. Part Number is 602092M (Same for both alarms)
Programming:
1. Ignition off.
2. Disconnect the red wire (remove the fuse).
3. Press and hold the anti-theft button (shorts the black/grey wire to earth)
4. Re-connect the red wire while holding the anti theft button.
5. Check that the vehicles LED has come on and the alarm emits a sound.
6. Press the new remote control key button.
7. The alarm should now beep and the LED will turn off. This signals that the code has been
accepted.
The alarm can remember up to eight keys at a time. If a ninth key is programmed then the first one
will be forgotten.
If you have any problems with these alarms contact Piaggio Ltd. Accessory Department 020 7401
4329.
Remember that a faulty alarm will not be covered by warranty. It is covered by a twelve month
guarantee from Fowlers of Bristol.
11
2 of 2 Piaggio Ltd. 04/11/02
GILERA KEYS
The following photograph shows the different types of keys used on the recent
Gilera models.
Only the Runner VX / VXR has an immobiliser. Note the symbol on the key that
denotes an immobiliser chip is fitted.
Later Runner FX / FXR keys look the same as the VX / VXR key but they do not have
an immobiliser chip and the symbol is not on the key.
Runner FX / FXR = the shape shown in the picture is 563585 this has been
superseded to 576719 this looks like the VXR key but does not have an immobiliser
chip.
SKP 50 = 574690
ICE 50 = 576719
9
Piaggio Ltd. 04/11/02
Tech Tips. #1 / 2004
1. H@K and GSM fork oil.
Front forks on H@K and GSM need 200cc of 10W fork oil in each leg.
Ref. Mario
2. B 125 Transmission Cover.
It is possible to remove the transmission cover from a B 125 with the engine in
the frame. Oh yes it is, say Garozzo M/C of Sidcup.
Remove the cover screws and clutch shaft centre nut as usual. It is now
possible to get the cover out far enough to remove the clutch drum. Once
the clutch drum is removed it is possible to remove the cover.
Ref. Garozzo M/C
3. X9 500 Tappet adjustment.
It is possible to check / adjust the tappets on an X9 500 with the engine in
the frame.
Remove r/h foot board / body work.
Remove the foot board mounting frame (3 x 6mm bolts)
Place a bar or piece of wood under the rear wheel.
Take out the top mounting bolt from the right hand rear shock absorber.
Then push it forward, pull to one side slightly and pull it as far back as
possible.
Take out the bottom mounting bolt from the left-hand rear shock
absorber. Then push it back as far as possible.
You can now raise the rear of the engine high enough to allow access to
the rocker box cover and then the tappets. Use a length of wood under
the rear tyre as a lever to raise the engine and them block the engine
securely.
Ref. Adam
4. 50cc Indicators.
If you find a fairly new 50cc with indicators that flash normally with engine off
but become fast or erratic when the engine is running you should also find
that a non-resistor plug cap is fitted.
Fitting a resistor cap should cure the problem.
Please note that they do not all have this problem so do not change the
cap unless you have the fault.
Ref. Tech Support
5. Pure jet fault code.
The diagnostic fault code list in the service station manual includes G50
P0250. This code should be G50P0251.
Ref. Mario
6. 2004 Colour Codes.
New colours for 2004 and their associated last two digits of the painted item
part numbers.