Piaggio, Vespa, Gilera, Technical Notes and Workshop Reference
Piaggio, Vespa, Gilera, Technical Notes and Workshop Reference
Piaggio, Vespa, Gilera, Technical Notes and Workshop Reference
This reference file has been built up over the last twelve years at Piaggio Ltd,
To help with fault finding, assembly understanding and to clarify and expand
on technical information contained in Service Station Manuals and parts
catalogues supplied from Italy.
Most of these pages have been created to help answer often asked questions
I hope you find it useful.
If you find an amended page please destroy the original to avoid any
confusion.
If you find any mistakes or you feel that the information could be better
presented or improved please contact me at Piaggio Ltd, after sales.
DISCLAIMER.
The information supplied here is accurate to the best of my knowledge but no guarantee is
given as to the accuracy or suitability of this information. This information should always be
used in conjunction with the relevant Piaggio manuals.
Piaggio Ltd, reserves the right to amend or withdraw any information contained here
without prior notification.
Piaggio Ltd, its employees and agents can not be held responsible for any inaccuracies or
omissions in this information. Nor can they be held liable for any consequence of using this
information.
David Champion
Piaggio Ltd.
Technical Services
© Piaggio Ltd 1995 - 2006
i
Technical / After sales contacts:
For any After Sales problems or questions, your first contact should be your
Regional After Sales Manager.
ii
Chapter 1 Chapter 5
2 Stroke Auto engines Electrical General
1. 50 / 80cc Charging early type 1. X9 Range General Notes
2. 50 / 80cc Charging later type 2. X9 Range. Under the front Panel
2a. NRG Charging & Gauges 3. Stator Coil Values - Quick Ref.
2b. NRG Power Instrument connection 4. Auto Choke Operation
3. 50cc 2t Ignition 5. Fuel Gauge Circuit
4. 125 & 180cc Charging / Ignition 6. Digital Instrument Display Notes
5. 125 & 180cc Indicator circuit 7. Remote Seat Release
6. 125 / 180cc Ignition 8. Setting the 2 button Digital Clock
7. Runner 125 / 180cc 2t Fuses Chapter 6
8. Diesis 100 Ignition / Charging Fuel Systems
9. Purejet 50 Charging / Ignition 1. Typhoon 80 / 125 Fuel System
10. Purejet 50 Indicators / Oil Check 2. DNA Fuel Systems
11. Fly 50 Charging / Carb heater 3. Hexagon (EXS1T) Fuel System
Chapter 2 4. Pumped Fuel Systems
Leader / Quasar engines. 5. Vespa PX Fuel Tap
1. B125 / 200 Ignition / Charging Chapter 7
2. B125 Notes Mechanical
3. B125 Fuse explanation 1. Fitting Main Bearings. All 2t autos.
4. DNA 125 / 180 Ign. / Charging 2. Vespa PX Clutch assy.
5. DNA 125 / 180 Switch Wiring 3. Piston & Small End Sizes
6. ET4 125 Ignition / Charging 4. Up Side Down Forks
7. Hexagon GTX Ignition / Charging 5. Spark Plug List
8. Runner VX / VXR Ign./Charging 6. Oil List
9. X9 125 / 180 Ignition / Charging 7. Tyres / Wheels Piaggio
9a. X9 125 Indicator Wiring 7a. Tyres / Wheels Vespa
10. Zip 125 Ignition / Charging 8. Tyres / Wheels Gilera
11. General notes 9. Keys Gilera
12. Immobiliser System explanation 10. Keys General
13. Vespa GT 125 / 200 Ignition / Charging 11. De-Restriction Notes
14. Vespa GT Fuses 12. Chassis Number Location
15. Skipper ST Ignition / Charging 13. Quick Reference Guide
16. Skipper ST Fuses 14. Service Limit List
17. Skipper ST replacement instrument panel Chapter 8
18. X9 250 Evo Ignition / Charging Injected Vehicles
19. Fly 125 Ignition / Charging 1. X9 500 ignition
19a Fly 125 Instrument panel connections 2. X9 500 lighting
20. X8 125 / 200 Ignition / Charging 3. X9 500 Centre Stand wiring
21. X8 Seat & Trunk Release 4. Nexus 500 Instrument panel connections
22. X8 125 / 200 Fuse Explanation Chapter 9
Chapter 3 Tech Tips Collection
4 Stroke (Non Leader) engines 1. Tech Tips 01
1. Coguar 125 Ignition / Charging 2. Tech Tips 02
2. ET4 (ZAPM04) Early Charging 3. Tech Tips 03
3. ET4 (ZAPM04) Late Charging 4. Tech Tips 04
4. ET4 (ZAPM04) Immobiliser Notes 5. Tech Tips 05
5. Hexagon GTX 250 Ign./ Charging
6. Liberty 125(non Leader) Charging
7. X9 250 Ignition / Charging
8. X9 250 Notes
9. X9 250 Fuse Explanation
10. 50cc 4 stroke Ignition / Charging
11. 50cc 4 stroke Restriction Notes
Chapter 4
2 Stroke Manual engines.
1. H@k / GSM Ignition / Charging
2. H@K / GSM Notes
3. H@K / GSM Wiring Diagram
4. Vespa PX Ignition / Charging
5. Vespa PX Start Permissive Circuit
6. Vespa PX Indicator Circuit
7. Vespa T5 Horn circuit
8. Gilera RCR 50 Ignition / Charging
9. Gilera RCR Notes
3
Chapter 1
Electrical systems
Electrical Systems
Electrical Systems
Electrical Systems
Two Stroke
Manual Engines
Electrical Systems
General
Fuel Systems
Mechanical Systems
Injected Vehicles
Tech Tips
A collection of the
Tech Tips
previously published
on the Piaggio Portal
01
02
03
04
05
50 / 80cc 2T Charging (early vehicles)
Piaggio Ltd. 30/09/2005 5 pin regulator
BLUE BLUE 3
7.5 amp
RED FUSE
RED
ON
+ BATTERY
IGNITION
SWITCH OFF 12v
RED 12v 4ah - 50cc
12v 5ah - 80cc
WHITE
1
YELLOW
DC SERVICES
Brake light
Horn
GREY / BLUE
AC
SERVICES
Head light
Tail light
GREY / BLUE
Instruments
YELLOW
GREY
WHITE
BLACK
CHOKE UNIT GREY
A A G B+
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the early 50cc and 80cc two stroke wiring using a five pin connector on the rectifier /
regulator. Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on when the starter button is pressed.
* Two completely separate circuits for AC & DC.
AC is full wave and regulated
DC is half wave rectified and regulated
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
NOTES.
Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter motor
but not the DC circuit or ignition circuit.
1-1
50 / 80cc 2T charging
Piaggio Ltd. 30/12/2005 8 pin regulator
YELLOW
2 7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION SWITCH
+ BATTERY
ON
OFF
12v
BLUE
1 WHITE
OIL
WARNING
LIGHT OIL TANK
SENDER
DC SERVICES
Brake light
GREY / BLUE Horn
AC
SERVICES
Head light
GREY / BLUE
Tail light 4
WHITE
BLACK
Instruments NOT
USED TO INDICATOR
see note BLUE / BLACK SWITCH
CHOKE UNIT GREY
YELLOW
1 2 3 4 5 6 7 8
OIL
LIGHT
TIMER
RECTIFIER
REGULATOR &
REGULATOR
* This diagram shows the later 50cc and 80cc two stroke wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* RECOGNISE THIS CIRCUIT: If the oil warning light comes on for 15 seconds when ignition is turned on.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay and oil light check function.
* The choke is supplied with 12v AC when the engine is running .
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
* Rectifier regulator pin 3 & 4 are both out puts from the timer so the wire could be connected to either pin.
1-2
NRG (up to Mc3) & ZIP Cat. Charging & Guages
Piaggio Ltd. 30/09/2005 8 pin regulator
YELLOW
2 3
7.5 amp
FUSE
BLUE
RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
FUEL
BROWN
BROWN
1
FUEL OIL
WARNING WARNING
LIGHT LIGHT DC SERVICES
WHITE / VIOLET
WHITE / VIOLET
BLUE / RED
Brake light
Horn
WHITE / GREEN
WHITE
YELLOW / GREEN
FUEL
SENDER 5
UNIT
5
TO INDICATOR
SWITCH
4
AC
YELLOW / GREEN
SERVICES
WHITE / VIOLET
GREY / BLUE
Head light
BLUE / RED
Instruments
BLUE / BLACK
TESTS
1. Grey / Blue to earth = 25-30v AC YELLOW
stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC
1 2 3 4 5 6 7 8
stator and battery disconnected and engine at
2000 rpm.
3. Ammeter between red wire and battery positive
= 1.5-2 amp with fully charged battery and TIMER
1-2a
- NRG POWER Digital Instrument Panel Connector -
11 12 13 14 15 16 17 18 19 20
1 2 3 4 5 6 7 8 9 10
1-2b
50cc 2t Ignition
Piaggio Ltd 25/08/05 Piaggio Ltd
This circuit could apply to any twist & go 50cc two stroke with or without a rev counter
IGNITION SWITCH
ON REV COUNTER
OFF
GREEN
COMMON EARTH
Champion NR2C FOR
NGK BR9ES INSTRUMENT PANNEL
GREEN
STATOR
GREEN
Ignition
GREEN Charging Coil
WHITE
WHITE
RED
RED
IGNITION PICK UP
TESTS
1. UNPLUG STATOR and CDI. GREEN WIRE SHOULD BE
CDI / COIL EARTHED WHEN IGNITION IS "OFF"
CDI / COIL 2. CHECK CHARGING COIL.
unit GREEN TO WHITE = 980 ± 50 ohms.
unit 3. CHECK TRIGGER COIL.
RED TO WHITE = 88 ± 5 ohms.
4. SPARK PLUG
NRG's are now supplied with Champion N1C plugs
The NGK equlivilent is B10ES.
This plug is very cold running and may not suit all riders.
If you find that a machine is fouling plugs try fitting an
NGK B9ES.
NOTES
1-3
125 & 180cc 2t charging / Ignition
Typhoon, Skipper, Hexagon, Runner
WHITE YELLOW
BROWN
RED IGNITION
PICK UP
GREEN
STATOR
RED
BATTERY +
YELLOW
12v
FUSE
RED
IGNITION SWITCH
ON
OFF
COOLING FAN
ON
WATER COOLED
PURPLE GREEN RED MODELS
WHITE
SUPPLY
CDI TO
Unit SYSTEMS
NOTES
* Choke and Carb' heater will have a supply with ignition turned on but the
rectifier / regulator will only complete the circuit to earth when it detects a CHARGE
charge. I.e. the engine is running. WARNING
* The Charge warning light goes out when the engine is charging because +12v LIGHT
D.C. is applied to both sides of the bulb, not because the circuit is broken.
* On water cooled engines the cooling fan is always live, the thermostat switch is
on the earth side. So a battery going flat could be caused by a faulty fan or fan
switch.
* The starter solenoid is always live so is a possible cause of a battery going flat
YELLOW
YELLOW
BROWN
WHITE
TESTS
GREY
RED
1. Stator Output.
Yellow to Yellow 27 - 31 v A.C.@ 2000 rpm. Unplug regulator.
Green - White 50 -150 ohm. Runner & Hexagon.(Stator un-plugged) A L C B G G
100 -160 ohm. Skipper & Typhoon.(Stator un-plugged)
Red - Brown 90 -140 ohm. All models. (Stator un-plugged)
2. Charging.
Between Red & Battery positive: >< 8.5 amps@ 2000 rpm with a fully
charged battery (13.5v) Choke
3. Battery voltage must be present at terminal "C" with ignition on or the output Control
from terminal B will be unregulated. Battery will boil, bulbs will blow etc. DC
MAIN FUSE: Rectifier
Runner (ZAPM07 / 08) 25 amp. Regulator
Out put only when
Hexagon (EXS1T & ZAPM05 / 06) 25 amp. charging
Typhoon (ZAPM02) 15 amp.
Skipper (CSM1T) 7.5 amp.
1-4
125 / 180 Two Stroke INDICATOR CIRCUIT
Piaggio Ltd 11/09/2003 Piaggio Ltd
BLACK
STARTER STARTER
RELAY SWITCH
INDICATOR
RELAY
BE
L B
+ 12V DC OIL WARNING
LAMP
S
STOP SWITCH
BLUE / RED
YELLOW
BLACK / BLUE
INDICATOR SWITCH
ABOVE. Vehicles 1999> Cirduit with oil check light that comes on when ignition is switched on.
Refer to the Service Station Manual. Also Technical Notes 2/99 and 3/99.
BELOW. Vehicles <1999 Circuit with oil check light that comes on when brake is held on and starter
button is pressed.
WHITE / RED
INDICATOR
RELAY
STARTER
LOW OIL RELAY
WARNING
OIL WARNING SWITCH
LAMP
DIODE
INDICATOR SWITCH
BLACK / BLUE
1-5
125 / 180 2T Ignition
Hexagon LX / LXT
Piaggio Ltd. 11/09/2003 Runner FX / FXR
Skipper & Typhoon 125
IGNITION SWITCH
ON
OFF
GREEN BLACK
GREEN
STATOR
WHITE
BROWN
RED PURPLE
NOTES.
* The ignition circuit is a separate self-contained circuit with no fuses and no connection to the other
electrical circuits on the vehicle. It has a separate charging coil in the stator (Green & White wires).
* The ignition switch contacts are OPEN when the engine is RUNNING. Contacts are CLOSED when
switch is turned OFF, this allows the system to discharge to earth. When fault finding, if there is no spark
then check the "green" and "purple" wires to see if there is a "leak" to earth. Unplug stator & CDI, check
green to earth: Ignition on = no continuity. Ignition off = continuity.
* A "Resistor" type spark plug and a resistor plug cap should always be fitted.
* This circuit does not require the engine to chassis earth. But if that earth lead is missing it is possible that
trying to use the starter motor could force excess current through the CDI and damage it.
Always prove you have a good engine to chassis earth connection.
1-6
FUSE EXPLANATION
Runner FX 125 & FXR 180
Notes.
• Ignition circuit is completely separate and self powered. It does not have any fuses.
• The cooling fan is permanently live and is protected by the main 25 amp fuse.
• The starter motor supply is not fused.
3
Lighting
Switch
1-7
Piaggio Ltd. May 2000
DIESIS 100 Charging / Ignition
Piaggio Ltd. 11/06/02 Derbi engine
Yellow / Green
Yellow / Green Indicators NGK
RIGHT B9 ES
OFF
LEFT
Yellow
Yellow / White
AC Supply Black / Red
Yellow
Red + 5o C Green / Black
Yellow / Green
Thermostat
Ignition Switch
Green / Black
DC Supply Black Carb. Heater LOCK
Black OFF
Red ON
To
starter 4 Red / Blue Green
solenoid
amp Red Orange
Yellow / Green Black Red / White
+ BATTERY
Orange - Indicator switch Red / Blue - DC supply
Rectifier
Earth wires are - Yellow / green. Regulator
Indicator
&
Relay
Yellow wire is AC supply. Regulator
Red / Blue wire is DC supply.
Engine earth is very important.
Carb heater is driven by AC power via a thermostat.
No separate Ignition pick up, CDI is triggered by the AC wave.
Ignition is earthed to stop the engine.
TESTS.
Stator: Yellow - Earth = min 25 v AC. White / Red - Earth = min 30 v AC. Engine at mid rpm.
Yellow - Earth = 0.9 ohm + 0.2. White / Red - Earth = 1.1ohm + 0.2. Stator un-plugged.
Black / Red - Earth = 238 ohm + 10%. Stator un-plugged.
Regulator: Yellow - Earth = 13.5 + 0.5 v AC. White / Red - Earth = 13.5 + 1.0 v DC. Engine at mid rpm.
Ignition: HT coil secondary resistance = 5 - 6 K ohm. Unit un-plugged.
1-8
PUREJET 50 IGNITION / CHARGE
Piaggio Ltd. 02/09/2003 GILERA RUNNER
BROWN
RED OFF
15 amp Champion
STATOR RG6YCA
RED
FUSE
BLUE
YELLOW 15 amp
YELLOW
YELLOW HT COIL
To starter
relay
BLUE
BATTERY +
BLACK / VIOLET
12v
BLUE
BLUE
BLACK / VIOLET
ORANGE
BROWN
BLUE
BLUE
RED
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
~ ~ ~ +
SYSTEM NOTES.
* 3 Phase AC.
* Permanent live battery feed to Rectifier, ECU, HT Coil (blue wire). Any of these could drain the battery if they were faulty.
* HT Coil is trigered by the BLACK / VIOLET wire being earthed via the ECU.
TESTS:
Stator: Disconected. Any yellow to any yellow = 0.7 - 0.9 ohm. Any yellow to earth = No continuity
Pick Up coil value is not quoted.
Rectifier / Regulator: With a charged battery the possible voltage must not exceed 15.2 volts.
1-9
Purejet 50 Turn Signals & Oil check
Piaggio Ltd. 12/01/2004 Runner
ON
Ignition Switch
15 amp
Red / Blue
Fuse's in
Orange
Battery
Compartment
Blue
Red
White
B
Black
E Oil Tank
Yellow
S Sender
Black / Blue
L Low Oil
Warning
LOW Light
White
White / Red
Yellow Yellow
RIGHT
Turn
OFF Indicator
Switch
LEFT
Black / Blue
Right Turn Indicators
Left Turn Indicators
* The low oil warning light check function is controlled by the indicator relay.
* The oil check light should come on for 15 seconds when the ignition is first turned on.
* If the system fails: first check the 7.5 amp fuse located under the front grill (horn) panel.
1 - 10
Fly 50 & Vespa LX 50 charging & carb heater
Piaggio Ltd. 13/12/2005 2 stroke engine
YELLOW
2 7.5 amp 3
FUSE
BLUE RED
IGNITION
SWITCH
ON +
OFF BATTERY
12v 4ah
RED / BLUE
WHITE
GREY / BLUE BLUE
1 DC SERVICES
Brake light WHITE WHITE
Horn OIL TANK
WHITE SENDER
Carburettor
heater
control
OIL
WARNING
LIGHT TO INDICATOR
CARB. HEATER SWITCH
Lt. BLUE
ORANGE
ORANGE / BLACK
4
CHOKE UNIT
YELLOW / BLACK
BLUE / BLACK
RED / GREEN
WHITE / RED
YELLOW / BLACK
YELLOW
BLACK
GREY / BLUE
NOT
AC USED
AC
1 2 3 4 5 6 7 8
SERVICES
Head light YELLOW / BLACK
Tail light OIL
LIGHT
Instruments TIMER
RECTIFIER
GREY / BLUE REGULATOR &
REGULATOR
This diagram shows the Fly 50 & Vespa LX 50 two stroke wiring, it is basically the same as other 50 two strokes
but there are a few slight variations including the electric carb heater.
TESTS.
y Stator out put. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
y Stator out put. Yellow to Blue = 26-30v AC stator un-plugged and engine at 2000 rpm.
y Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000
rpm
y Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
y The carburettor heater is DC powered but the controller is activated by AC so it will only turn the heater on
when the engine is running (AC output is detected).
y The choke is AC powered as normal. It is not controlled by the Carb. heater controller.
y Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
1-11
B 125 / 200 ignition / charging
Piaggio Ltd. 25/08/05 With IMMOBILISER
OFF
Blue
G
Ignition
Pick up White / Blue Blue / Black
White
White
Cooling
Fan Fan
Green Switch
Yellow Green
Red / Black
White
Ignition Relay
White RUN
STOP
CR 9EB White
Choke Unit White
White / Black
Red / Black
Red / Blue
Yellow / Blue
Blue
15 15 4 Red / Black
15
Green Indicator
Black / Blue Switch
HT Coil
CDI / Immobiliser
Purple
3 21
Red Black 8 76 54
antenna
1. Seat has electric release. Only works when ignition switch is in the “off”
position.
If seat lock fails to operate:
Check fuse “7” in rear fuse box. 4 amp red wire in & blue wire out.
Check for power on Blue wire at ignition switch
Check for power on White / Blue wire at ignition switch with ignition “off”.
Check the push button, Blue / Black should earth when button is pressed.
Seat lock, power socket and under seat light are all controlled by the same
fuse.
3. Immobiliser is like other Leader engines. There are separate notes to explain
the immobiliser system.
5. Spark Plugs.
Please note that the correct spark plugs are:
125cc :- NGK CR8 EB p.n. 828866
200cc :- Champion RG6 YC p.n. 828708 (or NGK CR7EB)
2-2
B 125 FUSE EXPLANATION
Piaggio Ltd. 08/05/2003 Piaggio Ltd.
WHITE / ORANGE
1 4 amp Engine start, run, warning lights
WHITE
WHITE / RED
12v DC from 2 4 amp Brake lights, start inhibit
ignition switch
RED / GREY
3 7.5amp Horn, Headlight flash
GREY
YELLOW
From light 4 4 amp Anologue, Inst. & side lights
switch
RED
12v DC from battery
5 6 7 8
4 10 15 15
a a a a
YELLOW BLUE
Headlight via relay Under seat, Light, Socket, Lock
2-3
DNA Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 DNA 125 / 180
G
ALTERNATOR
STATOR
7.5 7.5
Green amp amp
Power to
Fan Cooling
Lights, horn
Switch Fan Orange
Yellow instruments
Orange
+ BATTERY
3 21
12v ECU
8 76 54
12ah
Black Blue / Red
White / Black Green
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm. YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY, LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-4
DNA 125 / 180 Switch Wiring
Refer to Service Station Manual
Piaggio Ltd. 08/05/2003 594329 (02/01) page 4-23>
1 2 3 4 5 6
ON
OFF
IGNITION SWITCH
LOCK ITEM 6 ON WIRING DIAGRAM
PARK
BLACK
GREEN
OFF
HIGH
LOW
0
SWITCHES
ITEM 8
ON WIRING DIAGRAM
BLACK
GREY - BLACK
YELLOW - BLACK
BROWN
PURPLE
WHITE ORANGE
WHITE - BLUE
BLUE - BLACK
PINK
EMERGENCY
LIGHTS START STOP
ALL PUSH RUN RIGHT HAND
SIDE 0 0
SWITCHES
OFF ITEM 9
ON WIRING DIAGRAM
WHITE
YELLOW - RED
GREEN - BLACK
WHITE - BLACK
ORANGE
BROWN
YELLOW
2-5
ET4 Leader / LX 125 ignition / charging
Piaggio Ltd. 30/09/2005 With IMMOBILISER
Ignition Green
ON Ignition
Pick up Switch Power
OFF
to
services
Orange
G
ALTERNATOR
STATOR Red / Blue Carb. Heater
RG4HC
CR 9E
Yellow
Orange
Choke Unit
amp
via relay WHITE / BLACK
ORANGE
RED / BLUE
To Purple
Blue / PURPLE
Diagnostic
15 socket
ECU / Immobiliser
amp
Red / Blue Yellow 3 21
LED on antenna 8 76 54
Red instrument
Layout of pins
pannel in the ECU / immobiliser
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
9ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-6
Hexagon GTX 125 ignition / charging
Piaggio Ltd. 13/03/02 With IMMOBILISER
Ignition Green
ON Ignition
Pick up
OFF Switch
Orange
G
ALTERNATOR Red
STATOR Red
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue White
Rectifier / HT Coil / Black
Regulator
p/n: 82501R
Black Green
Red Red
GREEN
6 1 8 3 4 5 7 2
WHITE / BLACK
5 3 21
antenna
amp 8 76 54
2-7
Runner VX / VXR ignition / charging
Piaggio Ltd. 19/07/02 With IMMOBILISER
Green
Ignition Ignition ON
Pick up Power to
Switch OFF
services
Orange
G
ALTERNATOR
STATOR Red
Red
NGK 5
CR 8EB Green amp
Yellow Cooling
Fan Fan
Switch
Red / Blue
Choke Unit
White /
Rectifier / HT Coil Black
Regulator Green
p/n: 82501R
Black
Red Red
6 1 8 3 4 5 7 2 GREEN
WHITE / BLACK
RED / BLUE
Red / Blue
Purple RED
Headlight PURPLE
BLACK
via relay BLUE / BLACK
To YELLOW
Indicator Blue / Black
switch
Grey
/ Red Diagnostic
Yellow ECU / Immobiliser
Red / Blue socket
15
Yellow / Red antenna
amp
Red 3 2 1 LED on
8 7 6 5 4
Layout of pins
instrument
in the ECU / immobiliser Red pannel
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
10ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-8
X9 125 indicator wiring
18.
17.
19.
20.
21.
22.
23.
24.
31.
32.
32.
33.
34.
35.
8.
To RIGHT indicator bulbs. WHITE / BLUE 4.
2.
3.
9.
10.
11.
14.
15.
16.
25.
26.
27.
28.
29.
30.
LEFT INDICATORS RIGHT INDICATORS
Instruments panel
1 7 5 13 6 4 12 INDICATOR SWITCH
RED / WHITE RIGHT
LEFT
FUSES IN FRONT
WHITE / BLUE
7.5 amp
STORAGE
COMPARTMENT
PINK / BLACK
IGNITION SWITCH
GREY / BLUE
ON
OFF
BLUE / BLACK
ORANGE
RED
BATTERY + 10 amp
RED / BLACK
+ G G G
2-9a
X9 125 / 180 & 250 Evo ignition / charging
Piaggio Ltd. 15/10/2004 With IMMOBILISER
G
Fan
ALTERNATOR
Red / Black
STATOR Green
Fan Switch
Orange
Choke Unit
Yellow
Grey
/ Black
Lt. Blue Orange
RUN Emergency
STOP Stop
5
Side amp
UP
Stand
DOWN
Switch
Yellow / Green
Yellow / Blue
Rectifier / Red / White
Immobiliser Stand
Regulator LED Warning
p/n: 82501R
Red / Black
Power to 2 GREEN
Yellow 6 YELLOW
Lt. Blue
5 Lt. BLUE
2-9
ZIP 125 Leader engine ignition / charging
Piaggio Ltd. 13/08/2003 NO Immobiliser
Ignition Green
Pick up ON Ignition
Power
OFF
Switch
to
LOCK services
G
ALTERNATOR
Orange
STATOR
Yellow
Orange
Choke Unit
WHITE / BLACK
ORANGE
Purple
PURPLE
To BLACK
2-10
LEADER ENGINE
Ignition, charging & immobiliser
Use these notes in conjunction with the SERVICE STATION MANUAL
The electrical system on the new Leader engine is very different to previous two stroke and
four stroke Piaggio engines. The ignition, charging & immobiliser circuits do not function in
the same way and do not share common components with previous versions.
Ignition is now using the battery circuit. Everything shares one common supply.
Alternator has three phase (all yellow wires) and ignition pick up coil (green wire) outputs
only.
Rectifier / Regulator is very simple. Three phase (yellow) inputs and one output.
ECU unit has become more complicated. The one unit is responsible for: ignition,
immobiliser, indicators & choke unit.
Much of the circuit is the same on ET4 Leader, Fly 125, Super Hexagon GTX 125,
Liberty 125 Leader, B 125, Skipper ST, Runner VX / VXR and DNA 125 / 180, Vespa
GT 125 / 200 X8 125, X9 125 and Zip 125 but be careful because there are differences.
Early Skipper ST did not have an immobiliser, the later version does have it.
IGNITION.
When the ignition is turned on power is supplied to the CDI (terminal 5).
Ignition pick up is via green wire (terminal 2).
Output to the HT coil is via purple wire (terminal 3).
The unit is earthed via black wire (terminal 8).
CDI / IMMOBILISER
Note the ECU units have different part numbers for different models and engines size.
Refer to the diagram for each specific model. The wiring and wire colours may vary.
It is important that the correct part number is used as the ignition characteristics vary and
although the units look the same they are different!
HT COIL. 82597R = Common to most Leader engines. 82582R = Skipper ST & X9 125
Purple to Black - primary winding = 0.4 - 0.5 Ω
HT to Black - secondary winding = 3000 ± 300 Ω
Plugged in with engine cranking the peak voltage Purple to Earth = 100 vdc
2-11
1 of 2
Piaggio Ltd February 2004
IGNITION PICK UP COIL.
Un plug, check resistance, Green to Black = 105 - 124 Ω
Un-plugged with engine cranking the peak voltage Green to Black = 2 vdc
STATOR.
Any yellow to yellow should give continuity. Un-plugged, yellow to yellow = 0.7 - 0.9 Ω
Yellow to earth should not give continuity.
INDICATORS X9 125.
X9 has indicators driven by the digital instrument panel.
Three wires go to the switch from the panel. The switch earth’s the appropriate wire to
operate the indicators. Output to the indicators comes from the panel. See the explanation
diagram 2-9a.
CHOKE UNIT.
The choke is now controlled by the CDI. (not the regulator).
Power is supplied to the choke via the main switched wire from the ignition switch to the
ECU. The unit will not function until the engine is running when the CDI will complete the
circuit to earth (terminal 7).
Un Plugged, resistance across the connections = >< 30 Ω @ 20˚C
Plunger extension. Measure how far the plunger protrudes from the body when it is cold,
this should be 12.5 - 13.0 mm. Now connect the choke unit to a 12v battery. The plunger
should have extended to 18.5 - 19.0 mm within 5 minutes.
Supply. Orange or Red / Blue to earth = Battery volts with ignition on.
Orange or Red / Blue to White/Black = 13-14.5v dc (system volts) with engine running.
2-11
2 of 2
Piaggio Ltd February 2004
Piaggio, Gilera & Vespa
Immobiliser
systems
Systems covered:
Leader
Pre Leader
Quasar
Master
Published January 2006
1st edition
PRE LEADER
QUASAR
Page 16 - Programming
MASTER
Page 19 - Programming
Leader Immobiliser
PAGE 2 19/01/2006 EXPLANATION
1. The immobiliser system fitted to all Piaggio, Gilera & Vespa "Leader" engined vehicles operates in
exactly the same way.
2. Although the principle is the same the wiring differs on different models.
Refer to the wiring diagram and Service Station Manual for your specific model.
3. CDI and immobiliser are combined in one unit.
4. The CDI / immobiliser units may look the same but:
They have different characteristics on different models.
Ensure you fit the correct unit. Always order by part number .
5. The flashing LED on the instrument panel is the key to understanding how the immobiliser is
behaving. The list below shows what the LED can tell you.
Note that the LED should flash steadily all the time the ignition is off and the battery is connected.
If not, go to PAGE 7 for fault finding information.
6. If you have no spark you must first prove that it is not due to the immobiliser.
7. Keys should not be on a metal key ring or with other keys. Sometimes this can upset the system.
2 sec.
LED ON
1. Immobiliser not programmed
2. Transponder is detected
3. Engine will run to 2000rpm
LED OFF
LED OFF
0.7 sec.
LED ON
1. Immobiliser is programmed
2. Transponder is detected
3. Engine can run normally
LED OFF
page 2
Leader Immobiliser
PAGE 3 19/01/2006 NEW KEYS
NO
page 3
Leader Immobiliser
PAGE 4 19/01/2006 NEW LOCKS
Is the original
NO master key YES
available?
page 4
Leader Immobiliser
PAGE 5 19/01/2006 NEW CDI
I have the
The replacement CDI / immobiliser
NO master & service YES must be new and unused.
key
LED
Battery FUSES
+12v Switched Live
Permanent Live
page 5
Leader Immobiliser
PAGE 6 19/01/2006 Fault Finding
FAULT: Engines turns over but there is no spark when tested with a strobe light
Ignition
turned off
Power
Supply
Problem LED Turn
NO Flashing?
YES Ignition On
7
Immobiliser
is working One short flash
correctly
YES Goes out
8 Stays out
Immobiliser
needs
One long flash
programming
YES Goes out
9 Stays out
Immobiliser Transponder
needs not One long flash
programming detected YES Two short flashes
9 10 Goes out
Stays out
Transponder
not One short flash
detected
YES Two short flashes
10 Comes on
Stays on
NO
Transponder
not One short flash
recognised
YES Three short flashes
For an explanation of each fault 11 Comes on
Stays on
go to the relevant numbered NOTES page
page 6
Leader Immobiliser
PAGE 7 19/01/2006 NO LED
FAULT: With Ignition turned off the LED light is not flashing
Note. With an all new / virgin system the LED may not be flashing but the
check function flashes should occur when the ignition is turned on.
Charged Ensure a
Battery NO fully charged
? battery is connected
YES
NO
1. Check Fuse.
2. Check continuity of wire
to instruments.
3. Check continuity of wire
from instruments to CDI.
YES
1. Check Fuse.
Switched 2. Check continuity of wire
Live to NO from fuse to ignition switch.
CDI ? 3. Check continuity of wire
from ignition switch to CDI.
YES
Good
Check continuity from CDI
Earth NO connector to battery negative
?
CDI / Immobiliser
Return
3 21
ire
to
tif ls
8 76 54
w
en e
Page 6
id o d
y
to l m
a
EARTH
am u
gr ivid
ur i a d
LED
lo g d i n
co rin r to
w e fe
SWITCHED LIVE
s
R
i
PERMANENT LIVE
page 7
Leader Immobiliser
PAGE 8 19/01/2006 Immobiliser OK
FAULT: Engines turns over but there is no spark when tested with a strobe light
Ignition
turned off
LED Turn
Flashing?
YES Ignition On
Immobiliser
is working One short flash
correctly
YES Goes out
8 Stays out
We know that the immobiliser is working correctly so the immobiliser system can now be ignored
and normal fault finding can be continued.
If no fault has been found you should suspect the CDI unit.
* Fit a new CDI (not from another bike)
* Use the service key (not the brown master key)
* Check that the spark is restored. engine should start but it will not rev beyond 2000 rpm.
If the fault is cured you must program the CDI unit.
GO TO PAGE 9 for programming information.
page 8
Leader Immobiliser
PAGE 9 19/01/2006 PROGRAMMING
FAULT: I need to program the immobiliser unit
Notes.
1. It is not possible to re-program an immobiliser unit to a new master key.
Once it has been programmed it is irrevocably linked to that master key.
2. It is not normally possible for an immobiliser to loose it's program and then need
re-programming.
If it was programmed and working but now it is saying that it is not programmed,
First, check the HT lead and plug cap, It is possible that extreme electrical
interference from a faulty HT circuit could upset the immobiliser.
Plug cap must be at least 5000 ohms. Change the cap and lead if suspect.
A resistor plug must be used on all Leader engines.
Then try re-programming the immobiliser.
If it will not re-program then it is faulty.
Programming a new immobiliser.
1. Do not attempt to program a new immobiliser until you know that the fault is cured.
Attach the new immobiliser, use the service key (not the brown master key)
LED will give one long flash then go out and stay out. System is working correctly,
Immobiliser is not programmed
The engine should start but will not rev above 2000 rpm until the immobiliser is
programmed.
2. To program a new immobiliser
* Insert the brown master key and turn on for two seconds
* Insert the service key and turn on for two seconds
* (extra service keys are included here)
- Insert the extra service key and turn on for two seconds
* Insert the brown master key and turn on for two seconds
* The timing of the two seconds can be critical so use a watch to time it,
you may need to do the sequence several times before it is accepted.
* Changing from one key to the next should be done within ten seconds.
* An extra service key is not just added,
you must go through re-programming all the keys as above.
You are not re-programming the master key, the master key is giving permission for the
service keys to be added.
* You do not need to start the engine just to check if the programming has been successful,
Just turn on the ignition and watch the LED.
One short flash (half second) means the programming was successful.
One long flash (two seconds) means the system is still not programmed.
2 sec.
LED ON
1. Immobiliser not programmed
TURN IGNITION ON
2. Transponder is detected
3. Engine will run to 2000rpm
LED OFF
0.7 sec.
LED ON
1. Immobiliser is programmed
2. Transponder is detected
3. Engine can run normally
LED OFF
page 9
Leader Immobiliser
PAGE 10 19/01/2006 NOT DETECTED
The immobiliser knows the ignition has been turned on but it has not been able to detect the
transponder chip in the key.
page 10
Leader Immobiliser
PAGE 11 19/01/2006 NOT RECOGNISED
The immobiliser has seen the transponder chip so you know that the chip in the key is intact
and the aerial is working correctly.
page 11
Non Leader Immobiliser
PAGE 12 19/01/2006 EXPLANATION
The original Vespa ET4 (ZAPM04) was powered by an air-cooled four stroke engine that looked
similar but was very different to the Leader engine.
On the next page there is an explanation of the wiring for this engine.
Fault finding:
* Fault finding is done either with the diagnostic tester or a 12 volt LED.
* The tester is explained in the service station manual. Using an LED is explained here.
* The vehicle is not fitted with an LED in the instrument panel.
* You must connect a 12 volt LED to the test socket.
* The test socket is a grey two pin plug with nothing plugged into it located in a
large rubber sheath on the right side of the engine bay.
* Remove the helmet storage to access the socket.
Note. Keys should not be on a metal key ring or with other keys.
Sometimes this can upset the system.
0.7 sec.
LED ON
1. Immobiliser is programmed Immobiliser
2. Transponder is detected is working
3. Engine can run normally correctly
LED OFF
page 12
Vespa ET4 125 charge / ignition (non Leader)
PAGE 13 19/01/2006 ZAPM 04 Later version
1 2 3 4 5 6 7 8
IMMOBILISER UNIT
WHITE
GREY / BLUE
YELLOW
GREY
1. AC out
DECODER 2. AC in
To Indicators
3. not used
4. not used
5. DC out
VOLTAGE 6. Earth
STABILISER 7. Indicators
CDI UNIT 8. DC in
3 5 8 6 4
V 3 2 1 G W B R
AC DC
SERVICES SERVICES
PURPLE
PINK
GREY WHITE
WHITE / RED ORANGE (Serial Line) YELLOW
LIGHT BLUE
ON
IGNITION SWITCH
OFF
RED
GREEN
BLACK
WHITE
BLUE
BROWN
PINK
RED
WHITE
GREEN BLUE
GREEN GREEN
WHITE
Lt. BLUE
NOTES.
WHITE / RED * This Diagram shows the non "Leader" ET4 125 with the later type 8 pin rectifier / regulator.
* This charging and ignition system is very similar to Piaggio 50cc 2 strokes and totally different to the
RED / BLUE later "Leader" engined ET4 125.
* Three separate systems. DC, AC and ignition.
BLUE * Ignition is self generating. The green wire (charging coil) is shorted to earth to stop the engine.
Immobiliser. See separate notes for a full explanation of the immobiliser system.
* PINK wire is non switched live (battery voltage) feed to the immobiliser.
7.5 AMP * WHITE / RED is voltage stabilised power for immobiliser and CDI.
FUSE * When ignition switch is turned on the immobiliser and CDI are energised via the LIGHT BLUE wire.
The immobiliser uses the antenna to look for a recognised unique code from the key being used.
If the immobiliser recognises the key they it sends another unique code to the CDI via the ORANGE
PINK
wire (serial line). If the CDI does not receive that code it will not operate. It is this code that makes it
impossible to bypass the immobiliser box.
RED
* The diagnostic test socket will be found when the helmet compartment is removed.
Look on the right side for a large rubber shroud protecting several plugs and sockets.
The diagnostic socket is a grey two pin socket with nothing plugged into it.
+BATTERY You can connect a 12v LED or the diagnostic tester to this socket.
Test box use is well covered in the Service Station Manual.
Testing using 12v LED is covered in these notes.
12v
Tests. See the service station manual for a full explanation of testing the system.
Ignition. Stator (un-plugged) Green-White = 300 - 400 ohms. Red-Brown = 90 -140 ohms.
Loom. Unplug stator and CDI. Green wire should give continuity to earth with ignition OFF and no
continuity with ignition ON.
Charging. AC section. Un-plug regulator. Grey - Earth = 25v AC with engine at about 3000 rpm.
DC section. Ammeter between Battery + and red wire = at least 1.8 amps, fully charged battery
Disconnect battery. yellow - red = at least 15v AC @ 3000 rpm.
page 13
Quasar Immobiliser
PAGE 14 19/01/2006 EXPLANATION
The 250 cc Quasar engine is available with a CV carburettor or semi closed loop fuel injection.
The Quasar engine with a carburettor has exactly the same immobiliser function as a Leader
engine.
The Injected engine is detailed below.
This is only a quick reference guide for basic fault finding of the immobiliser system.
For a full explanation please see the Service Station manual.
The Quasar has an ECU with a separate immobiliser which is built into the aerial, so the ECU must
obtain authority from the aerial (active antenna).
Keys should not be on a metal key ring or with other keys. Sometimes this can upset the system.
See Note
Possible LED Flashing Codes on the
Next Page
Phase 1 Phase 2 Phase 3
2 sec.
LED ON
1. ECU not programmed
Any
Key
2. Transponder is detected A
LED OFF
3. Engine will run to 2000rpm
LED ON
1. ECU not programmed
Any
Key
2. Transponder is not detected B
LED OFF
3. Ignition is not possible
0.7 sec.
LED ON
1. Immobiliser is programmed
Service
2. Transponder is detected
Key
3. Engine can run normally
LED OFF
Immobiliser
is working
correctly
0.7 sec. 2 x 0.5 sec.
LED ON
1. Immobiliser is programmed
Master
2. Two service keys are programmed
Key
3. Engine can run normally
LED OFF
Could be
any number
from 0 to 7
page 14
Quasar Immobiliser
PAGE 15 19/01/2006 NOTES
LED flashing code notes.
Diagnostic Tester
If you use the hand held diagnostic tester you can check the immobiliser.
Select the "Errors" menu to see detailed fault information.
DISPLAY NOTES
Imm start inhib Yes / No Yes = Ignition is not possible (no spark).
LED remaining on in phase three (page 14 B,C,D,E)
Universal code Yes / No For production assembly line use only. Yes = Virgin ECU
Wrong Key code Yes / No Yes = Key transponder is seen but not recognised
LED - three flashes in phase two (page 14 E)
Programming.
Notes.
1. Do not attempt to program a new immobiliser until you know that the fault is cured.
Connect the new immobiliser, use the service key (not the brown master key)
LED will give one long flash then go out and stay out. System is working correctly,
Immobiliser is not programmed
The engine should start but will not rev above 2000 rpm until the immobiliser is
programmed.
2. To program a new immobiliser
* Insert the brown master key and turn on for two seconds
* Insert the service key and turn on for two seconds
* (any extra service keys are included here)
- Insert the extra service key and turn on for two seconds
* Insert the brown master key and turn on for two seconds
* The timing of the two seconds can be critical so use a watch to time it,
you may need to do the sequence several times before it is accepted.
* Changing from one key to the next should be done within ten seconds.
* An extra service key is not just added,
you must go through re-programming all the keys as above.
You are not re-programming the master key, the master key is giving permission for the
service keys to be added.
* It is not the keys that are programmed.
The immobiliser is being programmed to recognise the keys.
* You do not need to start the engine just to check if the programming has been successful,
Just turn on the ignition and watch the LED.
One short flash (half second) means the programming was successful.
One long flash (two seconds) means the system is still not programmed.
page 16
Master Immobiliser
PAGE 17 19/01/2006 EXPLANATION
Keys should not be on a metal key ring or with other keys. Sometimes this can upset the system.
For a full explanation of fault finding please see the Service Station manual.
See Note
Possible LED Flashing Codes
on the
Phase 1 Phase 2 Phase 3 Next Page
2 sec.
LED ON
1. System not programmed
Any
Key
2. Transponder is detected A
LED OFF
3. Engine runs only to 2000 rpm.
2 sec.
LED ON
1. Immobiliser not programmed
Any
Key
2. ECU is programmed B
LED OFF
3. Ignition is not possible
0.7 sec.
LED ON
1. Immobiliser is programmed
Service
2. Transponder is detected
Key
LED OFF
3. Engine can run normally
Immobiliser
is working
correctly
0.7 sec. 2 x 0.5 sec.
LED ON
1. Immobiliser is programmed
Master
2. Two service keys are programmed
Key
LED OFF
3. Engine can run normally
Could be
any number
from 0 to 7
page 17
Master Immobiliser
PAGE 18 19/01/2006 NOTES
page 18
Master Immobiliser
PAGE 19 19/01/2006 PROGRAMMING
Programming.
Notes.
1. Do not attempt to program a new immobiliser until you know that the fault is cured.
Connect the new immobiliser, use the service key (not the brown master key)
LED will give one long flash then go out and stay out. System is working correctly,
Immobiliser is not programmed
The engine should start but will not rev above 2000 rpm until the immobiliser is
programmed.
2. To program a new immobiliser
* Insert the brown master key and turn on for two seconds
* Insert the service key and turn on for two seconds
* (any extra service keys are included here)
- Insert the extra service key and turn on for two seconds
* Insert the brown master key and turn on for two seconds
* The timing of the two seconds can be critical so use a watch to time it,
you may need to do the sequence several times before it is accepted.
* Changing from one key to the next should be done within ten seconds.
* An extra service key is not just added,
you must go through re-programming all the keys as above.
You are not re-programming the master key, the master key is giving permission for the
service keys to be added.
* It is not the keys that are programmed.
The immobiliser is being programmed to recognise the keys.
* You do not need to start the engine just to check if the programming has been successful,
Just turn on the ignition and watch the LED.
One short flash (half second) means the programming was successful.
One long flash (two seconds) means the system is still not programmed.
page 19
Vespa GT 125 / 200 ignition / charging
Piaggio Ltd. 30/09/2005 With IMMOBILISER
G
ALTERNATOR Grey
STATOR
Red / Black
Green
Fan Cooling
RG4HC
Switch Fan
CR 9EB
Yellow
Orange
Choke Unit
RUN
STOP
Orange
Lt. Blue
Rectifier / Regulator White / Black
p/n: 82501R HT Coil
Green
Purple
Red / Black
GREEN
6 1 8 3 4 5 7 2
PURPLE
To BLACK
Note that the ECU fitted to the 125 and 200 have different characteristics.
They are NOT interchangeable.
+ BATTERY
TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12v GREEN TO BLACK (EARTH) = 105 - 124 ohm
12ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2 -13
Vespa GT Fuses
Piaggio Ltd. 19/08/2003
1 2 3 4 5 6
10 7.5 7.5 7.5 5 5
a a a a a a
RED / BLACK
12v DC from battery
BLUE
ORANGE ORANGE
Switched 12v Switched 12v
The wire colours shown here are different to those "on line" and in the owners hand
book.
The colours and fuse functions here are correct, they were checked on GT200
ZAPM312 * 2550.
FUSE:
1. 10 amp. Electric seat release. Headlights. Main beam warning light.
2. 7.5 amp. Intercom. Alarm. Immobiliser LED.
3. 7.5 amp. Intercom. Alarm. Water temp. Fuel warning & guage. Oil pressure warning.
4. 7.5 amp. Horn.
5. 5 amp. Stop light. start switch.
6. 5 amp. Side lights. Number plate light. Instrument panel lights.
MAIN FUSE.
A 15 amp fuse is located at the front of the under seat compartment.
2-14
Skipper ST ignition / charging
Piaggio Ltd. 30/09/05 With IMMOBILISER
Ignition Green
ON Ignition
Pick up Switch Power
OFF
to
services
Orange
G
ALTERNATOR
STATOR Red / Blue Carb. Heater
RG4HC
CR 9E
Yellow
Orange
Choke Unit
Green
Black
Headlight GREEN
6 1 8 3 4 5 7 2
Yellow
Red / Blue
LED on
15 instrument
ECU / Immobiliser
amp pannel
3 21
8 76 54
antenna
Red Layout of pins
in the ECU / immobiliser
+ BATTERY TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
12v YELLOW TO EARTH = NO CONTINUITY
GREEN TO BLACK (EARTH) = 105 - 124 ohm
9ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-15
SKIPPER ST 125 FUSE EXPLANATION
Piaggio Ltd. 06/01/2004 Leader Engine
RED
GREY 12 V DC from battery
To Head Light Relay 1 15 amp
RED
RED / BLUE
2 15 amp
IGNITION SWITCH
ON
OFF
RED / BLUE
ORANGE
RED / BLUE
1 2 3 4
7.5 5 5 5
a a a a
2-16
Replacing Skipper ST speedometer
Piaggio Ltd. 13/12/2005 With IMMOBILISER
The early Skipper ST did not have an immobiliser. The speedo unit for this vehicle
581308 (or 581307) is no longer available.
It must be replaced with 583271, this is the speedo fitted to later Skipper ST with
immobiliser.
To fit this new speedo you must make some modifications to the wiring at the plugs
which connect to the speedo unit.
Below are diagrams that show the plugs on the wiring loom as they appear on the vehicle
and also how they must appear to enable the new speedo to be used.
1. Confirm that the wiring on your vehicle is as shown on the "Original Loom" diagram
2. Remove the white / green and yellow / green wires from the large plug complete with
their connectors.
3. Remove the white and the brown wires from the small plug complete with their
connectors.
4. Re-fit these wires in the positions shown on the "Modified Loom" diagram.
It is possible to remove the connectors by carefully inserting a small screwdriver or
similar and pressing the retaining tag in.
View of the two plugs that connect to the speedometer
ORIGINAL MODIFIED
LOOM LOOM
WHITE / GREEN
VIOLET VIOLET
RED RED
WHITE
WHITE BROWN
2-17
X9 250 Evo ignition / charging
Piaggio Ltd. 05/05/2004 QUASAR Engine
G
Fan
ALTERNATOR
STATOR Red / Black
Green
Orange Fan Switch
Choke Unit
Main Relay
Yellow Lt. Blue Orange
Grey / Black
RUN Emergency
STOP Stop
UP Side
Stand
DOWN
Red / White Switch
Green
Yellow / Green
Yellow / Black
7.5 7.5
amp amp
Rectifier /
Regulator Yellow / Green
Black
HT Coil
White / Black
RG4HC Green
CR 9EB Diagnostic
Yellow / Grey socket
2 GREEN
Power to
7 WHITE / BLACK
Services
Yellow 6 YELLOW
Lt. Blue
5 Lt. BLUE
+Red
Indicators are powered by
BATTERY the digital instrument panel.
TESTS.
12v STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12ah GREEN TO BLACK (EARTH) = 105 - 124 ohm
REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF (Remove front 10 A fuse) , HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-18
Fly 125 Instrument connection
Piaggio Ltd 25/01/2006
You may find an incorrect wiring diagram, with wiring that does not match the vehicle.
This diagram should match the vehicle.
WHITE / GREEN 5
WHITE 4
YELLOW / GREEN 3
WHITE / BLUE 2
YELLOW / BLACK 1
BROWN
PINK
VIOLET
BLACK
Instrument
Illumination
Right turn
Earth
signal
Low fuel
High beam
warning
Yellow / Red
Fuel gauge Oil Pressure
To CDI unit
Immobiliser LED.
The LED has a permanent live feed, the CDI earths it when it wants it to light.
If the battery is connected the LED should have a live feed on the Red / Blue wire
If you short the Yellow / Red wire to earth the LED should light.
Oil Pressure.
Live feed to switch. Switch shorts it to earth to light the bulb.
Fuel Gauge.
Live feed to unit in tank. The tank unit shorts it to earth via a variable resistor.
If the gauge is not working.
Un-plug the instruments put a meter between white / green and black.
Low resistance (3 ohms) = full tank. High resistance (100 ohms) = empty tank.
This has checked the wiring and tank unit.
Low Fuel Warning.
Live feed to unit in tank. The tank units shorts to earth to light the bulb.
2-19 A
Fly 125 ignition / charging
Piaggio Ltd. 21/10/04 With IMMOBILISER
Ignition Green
ON Ignition
Pick up
OFF Switch Power
Orange to
services
G
ALTERNATOR
STATOR Orange To
Carb. Heater
headlight
switch
Yellow
Red / Blue
Orange
RG4HC
CR 9E Choke Unit
White / Black
Rectifier /
Regulator
p/n: 82501R HT Coil
Red / Blue
Orange
Green
Red / Blue
Black
GREEN
6 1 8 3 4 5 7 2
PURPLE
To BLACK
White Diagnostic
socket
ECU / Immobiliser
15 Red / Blue Yellow / Red
amp 3 21
LED on 8 76 54
Red instrument antenna Layout of pins
pannel in the ECU / immobiliser
+ BATTERY
TESTS.
STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12v GREEN TO BLACK (EARTH) = 105 - 124 ohm
9ah REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-19
X8 125 / 200 ignition / charging
Piaggio Ltd. 04/01/2005 With IMMOBILISER
G
Fan
ALTERNATOR
STATOR Red
Green
Fan Switch
Orange
Yellow Choke Unit
RUN Emergency
STOP Stop
Lt. Blue Power to
Red Services
Rear Fuse
Box
Immobiliser
Rectifier / LED
Regulator 15
Red / Blue To Indicator
10
Red / Black Switch
5
Yellow / Blue
White / Black
Red / Green
2 GREEN
7 WHITE / BLACK
1 BLACK / BLUE
Diagnostic Yellow 5 Lt. BLUE
socket 4 RED
6 YELLOW
Purple
3 PURPLE
8 BLACK
Black
Red / Black
3 21
8 76 54
Layout of pins
in the ECU / immobiliser ECU / Immobiliser
antenna
+Red BATTERY
TESTS.
12v STATOR: ANY YELLOW TO ANY YELLOW = 0.7 - 0.9 ohm.
YELLOW TO EARTH = NO CONTINUITY
12ah GREEN TO BLACK (EARTH) = 105 - 124 ohm
REGULATOR: VOLTAGE ACROSS A FULLY CHARGED BATTERY,
LIGHTS OFF, HIGH REVS = 14 - 15.2 V.
CHARGING: AMMETER IN RED WIRE = > 8 AMPS
WITH LIGHTS ON AND HIGH REVS.
HT COIL: PRIMARY = 0.4 - 0.5 OHM. SECONDARY = 3K + 300 OHM.
2-20
X8 125 Seat & Trunk Release
Piaggio Ltd. 30/09/2005 Piaggio Ltd.
ON
SEAT RELEASE
BUTTON IGNITION SWITCH OFF
LOCK
RED
ORANGE
RED / BLUE
RED / BLACK
GREEN
SEAT
SOLENOID
ANTENNA
TRUNK RELEASE
BUTTON
ET
IOL
V FRONT
WHITE FUSE BOX
RED / BLACK
BLACK
10 A
YELLOW
TRUNK
SOLENOID
GREEN
1
2
3 RED / BLUE RED / BLUE
4
6
7
10 REAR
11 FUSE BOX
12
10 A
VIOLET / BLUE
ORANGE / WHITE
YELLOW
ORANGE / BLACK
RED / BLACK
SOLENOID
CONTROL UNIT
15 A RED
+
BATTERY
12v
RED / BLUE
2-21
Coguar 125 Charging & Ignition
Piaggio Ltd. 04/02/2004 Honda XLR 125w Engine
RECTIFIER / REGULATOR
RED RED
GREEN BLACK
RED
IGNITION ON RUN BLUE YELLOW / BLUE
SWITCH
OFF STOP
STAND
WARNING
LIGHT UP
20 15 FUSES DOWN
1 X 20 AMP DPR8 EA9
STAND
1 X 15 AMP SWITCH
WHITE / GREEN
NEUTRAL
LIGHT
NEUTRAL
STARTER
IN GEAR
BUTTON
NEUTRAL
SWITCH
M
STARTER
RELAY WHITE / BLUE
IN
IGNITION
+
OUT
BLACK UNIT
BATTERY CLUTCH
BLUE (ECU)
SWITCH
12v
YELLOW / RED
WHITE / GREEN
NOTES
Three phase charging with inductive low voltage ignition.
The start & run permissive circuit is shown here in lighter detail.
For the engine to run the ECU must be earthed via the White / Green wire.
TESTS
Stator: Any yellow to any yellow = 0.8 ohm. Any yellow to earth should give NO continuity.
Regulated voltage: 14.0 - 14.8 volts with fully charged battery and lights on. Engine running at 5000 rpm.
3-1
Vespa ET4 (ZAPM04) charging
Up to ZAP04 * 51159 11/09/2003 5 pin regulator
WHITE
CHOKE CONTROL
GREEN
WHITE
WHITE / RED
GREEN / BLACK
YELLOW GREY
+12v DC from
start button
AC SERVICES DC SERVICES
GREY / BLUE
1
YELLOW
WHITE
GREY
BLACK
RED
A A G B+
3
RECTIFIER BATTERY +
REGULATOR &
REGULATOR 12v
* This diagram shows the early ET4 (non Leader) wiring using a five pin connector on the rectifier / regulator.
Refer to the separate diagram for later circuit using an eight pin rectifier / regulator.
* Three completely separate circuits for AC, DC & ignition.
AC is full wave and regulated
DC is half wave rectified and regulated
Ignition is the self powered CDI type typical on our two stroke scooters. Shorted to earth to stop.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
* If voltage at the B+ terminal falls below 8v (approx) the DC rectifier / regulator will not function so there will be no
output from the alternator on the DC circuit.
* Separate indicator relay.
* The choke is powered by the DC circuit but the relay to activate it is controled by the AC circuit.
Circuit will only be completed when both:
AC is present at relay terminal "B" and +12v DC is NOT present at the unmarked terminal.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
3-2
Vespa ET4 (ZAPM04) charging circuit
From ZAPM04 * 51160 11/09/2003 8 pin regulator
YELLOW
2
7.5 amp 3
FUSE
BLUE RED
RED / WHITE
IGNITION + BATTERY
SWITCH
12v
WHITE
ON
BLUE
OFF
GREEN
GREEN
BLACK WHITE
1
DC SERVICES
GREY / BLUE Brake light
Horn
WHITE
AC
GREY / BLUE
BLACK
Head light
TO INDICATOR
Tail light
WHITE / RED BLUE / BLACK SWITCH
Instruments
3&4 YELLOW
GREY
NOT
USED
1 2 3 4 5 6 7 8
RECTIFIER
REGULATOR &
REGULATOR
GREY
* This diagram shows the later (non Leader) ET4 wiring using an eight pin connector on the rectifier /
regulator. Refer to the separate diagram for earlier circuit using a five pin rectifier / regulator.
* The charging system is basically the same as the 50cc & 80cc two stroke Sferoids.
* Two completely separate circuits for AC & DC.
* Eight pin rectifier / regulator incorporates the indicator relay.
* The choke is supplied with 12v DC when the ignition is turned on but the circuit to earth is only completed
when the engine is running and 12v AC is supplied to the choke control relay.
TESTS.
1. Grey / Blue to earth = 25-30v AC stator un-plugged and engine at 2000rpm.
2. Yellow to Blue = 26-30v AC stator and battery disconnected and engine at 2000 rpm.
3. Ammeter between red wire and battery positive = 1.5-2 amp with fully charged battery and engine at 2000 rpm
4. Output to the indicator switch will be a 12v DC pulse with ignition on.
NOTES.
* Engine must be earthed to the chassis / battery. Lack of this connection will affect the AC circuit and starter
motor but not the DC circuit or ignition circuit.
3-3
ET4 IGNITION IMMOBILISER.
Original, Non Leader
General description
The ignition key contains an electronic digital code; this code must be recognised by the system before
the ignition system will function.
Thus the scooter has two forms of security – the key must physically operate the lock (in the normal way),
and the electronic code must be recognised by the system. In this way the scooter is safe against having
the ignition switch forced, or being hot-wired.
Main components
Decoder, which uses the antenna to read the electronic code of the key transponder.
CDI unit, which latches to the ON position only if an appropriate signal is received from the decoder.
Other components
7.5 amp fuse, which supplies +12V DC to the voltage stabiliser (located within the decoder box).
Voltage stabiliser (located within the decoder box), whose output (+12V DC) supplies power to the
decoder and the CDI unit via contacts in the ignition switch.
“Serial Line”, connects the decoder to the CDI unit, and conveys the authorising signal enabling the CDI
to latch to the “ON” position.
Normal Operation
The key grip contains a passive electronic transponder – a device that contains a unique pre-set digital
code, which can be read without direct electrical contact (similar to those used in the Datatag system).
The keys do not need any power and they do not contain a battery.
When the ignition switch is turned on, the decoder interrogates the key’s transponder.
Only if the decoder recognises the transponder’s electronic digital code will it send a signal via the serial
line to the CDI unit, enabling the otherwise conventional ignition system (alternator with pick-up and
charger coil, CDI unit and HT coil) to function.
However, the CDI unit and the decoder are also programmed to operate together as a matched pair; if
they detect a mismatch the CDI unit will not allow ignition.
3-4
Piaggio Ltd.
page1 of 6
To check the correct operation of the system
IT IS IMPORTANT THAT ON PDI AND AFTER ANY WORK ON THE IMMOBILSER SYSTEM, THE
CORRECT OPERATION OF THE SYSTEM IS CHECKED.
• Insert the red key with the hinged transponder in the flipped out position (this takes it out of radio
range of the antenna, thus enabling the system to be tested without the antenna automatically picking
up a code).
• Turn the ignition on and try to start the engine. IT SHOULD NOT START.
• Insert the blue key and try to start the engine. IT SHOULD START AND RUN NORMALLY.
Decoder and CDI units are initially manufactured as blank units. In this state (“Virgin”) and up to the time
they are programmed the immobiliser system will not offer any protection, and the ignition will function in
a conventional way. However, a “virgin” unit can be used as a substitute to aid in fault finding.
Programming functions can only be done with a red key. Once either the decoder or the CDI unit has
been programmed using a red key, they will only ever recognise that particular red key.
Therefore, it is vital that you USE ONLY THE BLUE KEY FOR ALL TESTING PURPOSES other than the
programming procedure itself.
If there is any fault with the system, the Immobiliser Test Box should be plugged in to the diagnostic test
socket. The test box (Part no 020319Y, Current dealer price £53.99 + VAT) is an invaluable, time saving
tool, and one which without doubt should be owned by all dealers.
Proceed as follows-
• With ignition off, turn on and wait for ‘On’ and ‘Pronto’ LEDs to illuminate.
• Turn ignition on. The ‘Seriale’ LED will flash, showing the signal on the Serial line.
• After a few seconds the appropriate LED will indicate the result of the diagnostic tests.
If the “No Serial line” LED lights up, it may be for the following reasons-
Serial Line circuit is broken.
Decoder is faulty
CDI unit is faulty
3-4
Piaggio Ltd.
page2 of 6
Diagnostic points to note-
To check for +12V DC power supply failure, check 7.5 amp fuse, and that +12V DC is present on
decoder terminals 3,5 and 8, and CDI unit terminal 1.
The CDI unit does not have its own earth lead, but is earthed to the alternator stator back-plate via the
white wire from terminal W. However, note also that back-plate and the engine itself is only earthed via
the electric starter motor lead. The decoder has its own earth lead.
There are two different types of transponder/decoder system; each type is not compatible with the other.
However this problem should only show up when trying to program new blue keys. In this case most
automotive locksmiths will be able to “clone” a new blue key if they are provide with a functioning red key.
These “cloned” keys will be recognised by the system without the need for programming.
CDI unit 1. Replace CDI unit (CDI can be replaced on its own).
2. Check for correct operation of system. Note that with a
virgin CDI unit the engine will start and run normally, but
the immobiliser system is inactive.
3. Program the CDI unit simply by turning on the ignition
switch using the red key
When programming keys do not have more than one transponder type key on the key ring, as the
decoder may pick-up both transponders.
3-4
Piaggio Ltd.
page3 of 6
VESPA ET4 IMMOBILIZER DIAGNOSTICS
When fault finding the ignition system on VESPA ET4, there is a very simple and quick check, which can
be done to give the Immobiliser the ‘all clear’. If you don’t have the effort-saving Immobiliser Tester (part
no. 020319Y) then insert a 12 Volt LED in the 2 pin socket (the blue/black lead is negative) located under
the helmet compartment and switch on the ignition whilst observing the LED. Note that the LED marked
Seriale on the Tester display shows this same signal.
It is advisable to get into the habit of using the blue key for all use and testing purposes other
than the programming procedure itself.
Normally-Functioning Immobiliser
The signal for a normally functioning Immobiliser system is a quick flash (0.7 seconds) and then the LED
remains off.
Immobilizer Fault-Finding
If the system is not functioning normally, it is recommended to obtain the Piaggio Immobiliser Tester. This
is by far the easiest way to diagnose faults. However, if for some reason this is not available, fault finding
can be done by observing the following.
2 secs 2 secs
LED off
0.5 secs
The above diagram shows the trace of the diagnostic signal for Decoder and CDI Units both
programmed, using a key with an unknown transponder (Table 2, case 5), resulting in 3 FLASHES during
the second phase of the diagnostic signal (Phase 2).
Phase 3: LED remains OFF if no fault is detected or ON if a fault is detected in the Immobilizer system
(the Tester does not consider a non-programmed CDI Unit a fault).
3-4
Piaggio Ltd.
page4 of 6
Table 1: Immobilizer Diagnosis Chart
Phase 2
LED Signal DIAGNOSIS
0 FLASHES NORMAL OPERATION
1 FLASH BREAK IN SERIAL LINE (ORANGE) OR DECODER EARTH (BLACK)
2 FLASHES NO TRANSPONDER DETECTED - FAULTY KEY OR IMMOB. ANTENNA
3 FLASHES TRANSPONDER DETECTED BUT NOT RECOGNISED BY IMMOB.
4 FLASHES VIRGIN DECODER AND PROGRAMMED CDI UNIT
KEY:
P = UNIT PROGRAMMED
V = VIRGIN i.e. UNPROGRAMMED
Y = ANTENNA FUNCTIONING
N = ANTENNA ABSENT or NOT FUNCTIONING
9 = IGNITION POSSIBLE
= IGNITION NOT POSSIBLE
PROG. = TRANSPONDER RECOGNISED THROUGH PROGRAMMING PROCEDURE
ANY = KEY WITH TRANSPONDER PRESENT BUT CODE DOESN’T MATTER
NOTES:
1. BLUE KEY - use for testing ignition after replacing Decoder and / or CDI Unit, otherwise you may
sacrifice perfectly good units; programs both Decoder and CDI Unit.
RED KEY - only use for programming operations and ONLY when you are sure the ignition system is
delivering a satisfactory spark.
The EXCEPTION to the above two points is when testing the Antenna with the RED KEY transponder
flipped out, as per the ET4 Service Station Manual.
2. LIMITED TO 2000 rpm
3. Normal operation with the either key
4. Break in the Serial line (orange lead) or Decoder not earthed properly (black lead)
3-4
Piaggio Ltd.
page5 of 6
3-4
Piaggio Ltd.
page6 of 6
HEXAGON 250
Charging & Ignition Circuit
STATOR
White
12 volt 12 ah.
CHOKE
HEATER
Ignition
Ignition Switch
Pick up
15 AMP
MAIN FUSE
Red Red
Yellow
Black Blue / Red
Green Black
SERVICES
RECTIFIER / REGULATOR
Black
Yellow / Black
White / Green
Blue / Yellow
Blue / Red
Red / Black
Green
Black
Spark Plug
IGNITION NGK. DPR6EA-9
SWITCH
See Note
Yellow / Black
White / Green
Green
Black
Green / Yellow
White / Black
Contacts are:
Open to
run.
Green
Closed to
Pink
?
stop.
Fuel Pump
• Note that the wire colour sometimes changes from one side of a conector to the other.
• The choke supply is ><12 volts AC (only when the engine is running).
• The fuel pump senses the engine speed and varies the supply rate accordingly.
TESTING. Green – Black: No continuity with ignition switch and kill switch to Run.
Yellow - Yellow - Yellow: 0.1 – 1.0 Ώ. Stator winding.
Black/Red – Black: 50 – 350 Ώ. Ignition charging coil.
Green/White – Blue/Yellow: 50 – 170 Ώ. Ignition pick up coil
Yellow/Black – Black: 0.1 – 0.2 Ώ. HT coil primary winding.
HT – Black: 3.6 – 4.6 K Ώ. HT coil secondary winding.
3-5
Piaggio Ltd. March 1999
LIBERTY 125 Charging Circuit
RECTIFIER / REGULATOR WITH AN EIGHT PIN CONNECTOR
STATOR
Yellow
15 A FUSE
CHOKE
UNIT Blue
White
/ Red + Battery
12v 9ah
Grey
White IGNITION
SWITCH
DC SERVICES
AC SERVICES BRAKE LIGHT
Red / HORN
HEAD LIGHT 7.5 A
Black TAIL LIGHT ETC.
CHOKE Fuse
CONTROL INSTRUMENT LIGHTS
To Indicator
RELAY
switch
Blue /
Grey Grey / Blue White Black Black Yellow
1 2 3&4 5 6 7 8
Green / Not used
Black
DC RECTIFIER
AC &
12v DC REGULATOR REGULATOR
from
starter button
Rectifier / Regulator
P/N: 294878
3-6
Piaggio Ltd. April 1999
X9 250 Charging & Ignition
Piaggio Ltd. 11/09/2003 Honda Engine
WHITE
RED / YELLOW HT COIL
MAIN POWER DPR7EA-9
FUSES IN
RELAY 15 7.5 7.5 10 FRONT
STORAGE 4
WHITE COMPARTMENT
WHITE / BLACK
RED /
IGNITION BLACK RED BLUE / YELLOW
SWITCH AUTO
2
CHOKE
BLACK
BLACK GREEN FUEL
DIGITAL
RED / RED / INSTRUMENTS THROTTLE PUMP
BLACK POSITION 5
BLACK
SENSOR
1 BLUE / YELLOW
7.5 10 10 20
FUSES IN RED / YELLOW
HELMET
COMPARTMENT
YELLOW / BLACK
RED
GREEN / BLACK
GREY / BLACK
YELLOW / WHITE
STARTER
STARTER MOTOR RADIATOR
RELAY 3 TEMP.
RED
RED / WHITE
BLACK RED
30 amp YELLOW / GREEN
START
RUN
PERMISSION
RELAY 9 ENGINE
RECTIFIER STOP
REGULATOR 10
RED /
GREEN /
BLACK
BLACK
WHITE / YELLOW
7 ORANGE / BLUE
WHITE / BLACK
YELLOW
6
+ BATTERY
12v
12 ah IGNITION
CONTROL
8 UNIT
YELLOW YELLOW
3-7
X9 250 (Honda engine)
* At PDI
Set the clock TIME and DATE.
Set the TRIP to MILES.
Reset all three SERVICE LIGHTS.
* To change km to miles.
Insert ignition key.
Press and hold down “Trip” and “M” buttons
Turn on the ignition.
The display should now have changed.
* To test System.
With ignition off.
Press and hold down “clock” and “set” buttons
Turn on the ignition
All the systems will check them selves and all the lights should come on.
Any blown bulb or faulty system will be obvious.
* Stop lights.
There are a total of five stop light bulbs.
If two or more bulbs fail the warning light will come on.
* Hazard Lights.
Ignition on
Press hazard button, lights will start flashing.
Turn ignition off.
To stop the lights, first turn the ignition on then press the switch.
* Battery charging.
Charging at idle (1500 rpm) with the main beam on should be 2 amps.
3-8
1 of 4
Piaggio Ltd. 11/09/03
* Low fuel warning lamp.
The light will only come on when it has received a continuous signal from the sender for 13
seconds.
* Relays.
The vehicle has five relays.
Starter relay p/n 496403 has a 30 amp fuse and is in the battery compartment.
Start Permission relay p/n 292332 is in the battery compartment.
Two head light relays and the main power relay are all the same p/n 58002R they are all
under the front shield, headlights are central and the power relay is on the near side by the
indicator.
* Headlights.
The headlights are controlled by relays and each has it’s own relay so if the light fails and it
is not the bulb, check the relay.
* Choke unit.
Temperature sensor in the radiator can control the choke.
If the temperature drops to 0 degrees C then choke will come on (no voltage to the unit)
* Valve clearance.
Set Cold.
Engine at TDC.
Valve clearance is one division on the scale.
Correct level
* Gear Box Oil Level
Remove the level screw.
If no oil comes out top up until oil drips
then wait until oil stops before re-fitting
the bolt.
* Indicators
The indicator relay function is part of the digital display cluster. P/n. 581413. There is no
separate relay.
The wires involved are:
Blue / Black - right turn
Grey / Blue
Red / Black - left turn
Note that to operate the indicators the handlebar switch shorts the relevant wire to earth.
Hazard lights work by the switch earthing the brown wire from the digital cluster.
3-8
2 of 4
Piaggio Ltd. 11/09/03
* Braking system
1. Three brake disks are all the same size. 200mm diameter.
2. Both master cylinders are the same size.
3. All brake pads are the same. p.n. 494966
4. L/H front and rear calliper are the same and have 22mm pistons
5. R/H front calliper has 24mm pistons.
6. L/H front and rear are linked together in the following way
When left hand lever is used
Up to 8 bar pressure the rear brake only is operated.
8 - 23 bar both brakes are applied.
Over 23 bar the amount of pressure to the front brakes begins to decrease relative to the rear.
7. The R/H front calliper is operated by the R/H brake lever and has no connection to the other
brakes.
3-8
3 of 4
Piaggio Ltd. 11/09/03
X9 250 CHARGING & IGNITION
Refer to the X9 Charging & Ignition diagram.
* Note that sometimes the wires coming from a component change colour at the connector that joins
them to the wiring loom.
* See the separate sheet for an explanation of the fuses.
* Charging is three phase, fully rectified.
* Ignition is digitally mapped and can not be manually adjusted.
Spark advance will be affected by:
• Engine speed.
• Throttle position. See # 1
• Coolant temperature. See # 3
3-8
4 of 4
Piaggio Ltd. 11/09/03
X9 250 FUSE EXPLANATION
Piaggio Ltd. 11/09/2003 Piaggio Ltd.
BLUE
1 20 amp Under seat light / Power socket
RED
WHITE / RED
12v direct from 2 10 amp Headlight relay
battery
RED / BLUE
3 10 amp Headlight relay
RED / BLACK
RED / BLACK
12v from battery 4 7.5 amp Digital Instruments
via start relay
1 2 3 4
15 7.5 7.5 10
a a a a
3-9
50cc 4 stroke Charging / Ignition
Piaggio Ltd. 22/11/01 Piaggio Ltd.
STATOR
Test 2 Test 3
BROWN
Test 1
PICK UP SUPPLY TO
INDICATORS
BROWN
GREY / BLUE
1 2 3 4
GREEN INDICATORS
SWITCH
CDI / COIL
BLUE / BLACK
UNIT IGNITION SWITCH
ON
OFF
LOCK
CHAMPION
RG4HC
GREY / BLUE
RECTIFIER
BROWN WHITE WHITE REGULATOR
TO START RED BLACK
RELAY
10A FUSE WHITE GREY
SUPPLY TO
DC SERVICES
Test 4
BLACK
+ BATTERY AC SUPPLY YELLOW / BLACK
TO LIGHTS
12v
CHOKE HEATER
7ah GREY
LIGHTS
ON / OFF
SWITCH
GREY
Only two wires come from the stator. The engine to earth connection is very important.
Battery voltage at idle = 13 v (Battery charged) max will be 14.5 volts at high revs. Meter between battery neg. & pos.
Battery charge at idle = 1.5 - 2 amps (lights off). max will be >5 amps at high revs with all lights on. Meter between red wire and battery pos.
Test 1: Brown - earth = ~170 ohm To test pick up coil. Stator un-pluged
Test 2: Black - earth = ~1 ohm To test charging coils. Stator un-pluged
Test 3: Blue / Grey - earth = 25 - 35 v ac @ 2000 rpm with regulator disconnected. To test charging coils.
Test 4: White - Black = ~8 M ohm. If the resistance is low it could cause the fuse to blow.
3-10
This information is intended only for authorised Piaggio dealers.
50cc Four Stroke Restriction
Piaggio do not advocate changing the restriction on any 50cc machine that may be used on public roads.
Remember that if a Piaggio, Gilera or Vespa 50cc moped is de-restricted it will be technically illegal. It will not conform to
Motorcycle legislation but it did conform to Moped legislation.
The restriction is the same on all 50cc four stroke models including the LX 50 4t, Fly 50 4t
and Zip 50 4t (China).
The main restriction on the 50 cc four stroke engine is electronic. There is no restriction in
the exhaust pipe.
AC6+0000
38 mm
Cut here
Cut 3 mm deep
at 45º 60 mm
1. Make a 3mm deep cut with a hacksaw in the position shown. Then fill the slot with silicon.
2. Remove the spacer washer between the front pulley halves.
3. Fit carburettor main jet size #78. Part number CM 142103
CUT
If you do not de-restrict. A moped should have a top speed of 45 km/h on the flat.
This engine will achieve that with an average size rider once it has run in for about 50 km.
Initial acceleration is brisk but changing the main jet for that mentioned above will help it
obtain top speed more easily.
3-11
Piaggio Ltd.
H@K & GSM Charging / Ignition
Piaggio Ltd. 23/04/02 Gilera engine
RED
WHITE
GREEN
ORANGE
RECTIFIER
REGULATOR BROWN
YELLOW
YELLOW
ORANGE
12v DC Services
FUSE
RED RED
IGNITION + BATTERY
SWITCH
12v
ON
OFF
R O G B
GREEN
RED
WHITE
ORANGE GREEN
GREEN RED
* Stator has separate coils for AC, DC and Ignition circuits. Champion N2C
Brown wire = supply for DC (battery circuit) NGK BR9ES
Yellow wire = supply for AC circuit
Green wire = supply for ignition
* Important that Stator has a good earth to engine and engine
must have good earth to chassis and battery.
* All Lights are powered by 12v AC
* Ignition is self generating and does not need the other electrical
circuits or the battery.
* Ignition is stopped by shorting the charge coil (green wire) to CDI / Coil
earth.
Check: Unplug Green wire from stator and CDI unit. You should
have continuity from green to earth with ignition OFF and no
continuity with ignition ON.
4-1
H@K & GSM Notes
Modifying the exhaust.
Piaggio can not recommend de-restricting for any reason. Be aware that if a moped is
de-restricted then it becomes a 50cc motorcycle and should be re-registered. These
vehicles may not conform to the requirements to become a motorcycle.
Un-officialy and to save possible damaging experimentation the following information
is given.
Enlarge the hole in the end of the exhaust, where it plugs into the engine.
The end of the exhaust is a piece of mild steel bar with a small hole drilled through it,
this hole needs enlarging to about 18 - 20mm (3/4 inch).
The steel bar is case hardened to comply with “anti-tamper legislation”. To soften the
hardening; heat the end to bright cherry red and then let it cool naturally. Then you
should be able to drill it.
Re-jet with a #60 or 62 main jet. It is a standard DellOrto jet.
Engine To silencer
2
Piaggio Ltd. 22/12/00
VESPA PX 125 / 150 / 200 Charging & Ignition
Piaggio Ltd. 04/07/02 Electronic Ignition
ON
DC OFF IGNITION
SWITCH
SERVICES YELLOW LOCK
GREEN
WHITE
RED
WHITE GREEN
RED
FUSE
+ BATTERY
7.5 12v
AMP
9ah
AC
RED GREY
SERVICES
RED / WHITE GREEN
C B G G
* AC output is regulated, full wave.
* DC output is regulated and half wave rectified.
* Alternator coils are connected in series.
REGULATOR
& * Ignition is self generating and totaly self contained.
DC RECTIFIER
REGULATOR
TESTS.
1. ALTERNATOR OUTPUT.
Unplug regulator. blue and earth = 26 - 30 vac @ 3000 rpm.
Unplug stator. red to white = 90 -140 ohms. green to white = 800 -1100 ohms.
2. BATTERY CHARGING.
Insert an ammeter betwen red wire and battery +.
With engine @ 3000 rpm and battery @ 13 vdc the ammeter should read 1.5 - 2 amps
* IN CASE OF OVER CHARGING.
un-plug the regulator and check that you have battery voltage on the red / white wire
that plugs into terminal "C". The regulator needs this input to function correctly.
* Check for good earthing between engine and chassis / battery / regulator.
4-4
PX 125 / 150 / 200 Start Permissive circuit
Piaggio Ltd. 25/08/2005 Refer to Service Station Manual
M BLACK PINK
STARTER
MOTOR WHITE-RED
PINK
YELLOW GREY
ON IGNITION
WHITE
SWITCH Starter Protection
OFF
Relay
Located under
RED
WHITE horn cover
RED
RED
7.5 amp
FUSE + BATTERY
12v
RED
RED GREY
C B G G G
4-5
PX 125 / 150 / 200E Indicator Circuit
Piaggio Ltd. 25/11/2005 Piaggio Ltd.
NOTE.
The indicators flash alternately; front - back (not both together)
This is to reduce the current needed
INDICATOR SWITCH
RIGHT
LEFT FRONT RIGHT FRONT
OFF
LEFT
RED WHITE
PURPLE
WHITE / BLUE
PURPLE
INDICATOR
RED / BLACK
WARNING
LIGHT ON
INSTRUMENT
PANEL C B G G
RED
RECTIFIER / REGULATOR
CONNECTIONS TO THE
INSTRUMENT PANEL
1. 12+ DC
4 5 2. Fuel Gauge
3. Low Fuel Warning NOTE.
4. Turn Signal Warning The Turn Signal Warning light has a
5. High Beam Warning permanent live feed (Grey).
3 6 6. Illumination / Lights On When the Red / Black wire is live the light
7. Earth will be off because it has 12+ on both wires.
When the Red / Black is not live the light
will come on because it is earthed through
the indicator bulbs
(only when the indicator switch is selected)
2
4-6
VESPA T5 HORN
Blue
HORN HORN SWITCH
NORMALLY ALTERNATOR
CLOSED
Yellow
Green
Black
REGULATOR
The T5 has a very simple 12 volt AC electrical system but one thing may not be clear
when you look at the wiring diagram.
It appears that the output from the alternator goes firstly through the horn, this does
not make much sense. If you are fault finding it is important that you understand how
the system works.
Explanation:
1. Out put from the alternator is the blue wire to the horn switch.
2. Horn switch is normally closed.
3. From there the yellow wire continues to the regulator.
4. Electricity always takes the easy path, so the current passes through the switch
rather than through the coil in the horn.
5. When the horn button is pressed and the circuit is broken and then the current will
have to pass through the horn and the horn will sound.
6. Power still reaches the regulator because the horn does not use all the power
available and it does not break the circuit.
7
Piaggio Ltd. October 1998
Gilera RCR & SMT 50 Charging / Ignition
Piaggio Ltd. 13/01/2004 Derbi engine
LIGHTS
WHITE
ON
RED
OFF GREEN
YELLOW / GREEN
RED / BLACK
WHITE / RED
BLUE
RED
GREEN / BLACK
RED
4A FUSE
RED RED
OUTPUT
TO DC + BATTERY
GREEN / BLACK
SERVICES
REGULATED 12v
OUTPUT
OUTPUT
4ah
GREEN
TO AC
WHITE
RED
TO SERVICES
INDICATOR
SWITCH
YELLOW
RED / BLACK
ORANGE
YELLOW
YELLOW / GREEN
RED
L + C YELLOW
G
GREEN
RED
WHITE
NOTES.
Earth wires are: YELLOW / GREEN.
Ignition is separate to AC & DC circuits. Ignition is shorted to earth to stop the engine.
STATOR VALUES. GREEN to EARTH = 820 ohms + 10% (CDI charging coil)
GREEN to WHITE = 700 ohms + 10%
RED to EARTH = 140 ohms + 10% (Ignition pick up coil)
RED to WHITE = 100 ohms + 10%
YELLOW to EARTH = 0.7 ohm + 10% (AC & DC circuit charging coil)
YELLOW to WHITE = 0.5 ohm + 10%
HT COIL secondary. 3.4 K Ohms + 15%. PLUG CAP. 5 K OHMS + 15%
Regulated Voltage: Fully charged battery and engine running: Battery voltage should be 13.5 v + 0.5 v.
4-8
GILERA RCR 50 & SMT 50
The RCR and SMT sre basically re-badged Derbi Sendas. The Senda has been produced in
several versions. The RCR and SMT are as follows:
No electric start.
No carburettor heater.
No radiator fan.
The ignition system uses the three wire Ducati system, not the five wire Leonelli.
Stator: 00H03300701
Complete rotor / stator assy: 00H03301011
CDI : 00H03330171
DE-RESTRICT.
Piaggio’s advice is: Do not de-restrict for any reason.
To improve top speed slightly:
Drill four 3 mm holes in the restrictor at the engine end of the exhaust pipe and fit a larger main
jet #60 if your bike is an early one with a #56 fitted as standard.
2005 onward the bikes have a #62 as standard, to improve change the needle to a #11 and
lower it by one notch. The #62 jet should be OK.
Or to fully de-restrict:
Remove restrictor tube from engine end of the exhaust pipe.
Increase main jet about four sizes.
Raise needle one notch.
Adjust slow running mixture, it is air bleed so screw in to richen.
Re-set idle speed to about 1900 rpm.
The extra power will allow the bike to pull higher gearing, you should fit a z=14 front sprocket,
p/n: 00H02805371.
Italy suggests fitting a one step colder plug but I doubt that we need to do this.
4-9
X9 RANGE.
CHANGING THE ODDOMETER DISPLAY TO SHOW MILES
This should be done at PDI. See manual 594284. Pages 9-4 and 4-57
1. Press and hold the TRIP and M buttons.
2. Turn on the ignition.
3. Release the buttons
The display will now show “miles”.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights
will come on at the correct time. Service Station Manual 594284 4-61 and owners
hand books have details for setting the clock.
If when you briefly press the button the light that comes on is not the one before
the one you want to reset then briefly press the button again to make the light
scroll along.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the
digital instrument panel and Black is to earth.
5-1
PIAGGIO LTD 14/10/03
X9 UNDER THE FRONT PANEL
The front panel between the headlights is retained by five cross head screws.
Remove the panel to access the service light reset button and the two headlight relays.
It is not necessary to remove the panel to adjust the headlight beam. The adjuster screw can be
accessed through the small grill near the top of the panel.
SERVICE LIGHTS
The time and date functions should be set at PDI to ensure that the service lights will come on at the
correct time. Service Station Manual 594284 4-61 and owners hand books have details for setting
the clock.
Wiring to the “RES” button is Grey/Green and Black. Grey/Green goes to the digital instrument
panel and Black is to earth.
5-2
Piaggio Ltd. 14/10/03
STATOR COIL VALUES
Refer to the relevant Service Station Manual / wiring diagram
Vehicle Ign. Pick Up Ign. Charging AC Circuit DC Circuit
50cc 2T Red - White Green - White Blue / Grey - Earth Yellow - Blue Red - Battery Positive
88 Ω (± 5 Ω) 970 Ω (± 50 Ω) 25 - 30v AC 25 - 30v AC 1.5 - 2 amp (charged bat.=13v)
50cc 2T Red - Brown n/a n/a Any yellow - yellow 0.7 - 0.9 Ω
Purejet Value not quoted Yellow to earth = no continuity
Runner 125 Red - Brown Green - White n/a Yellow - Yellow
Hexagon 2T 90 - 140 Ω 50 - 150 Ω 27 - 30v AC
Liberty 125 Red - Brown Green - White Blue / Grey - Earth Yellow - Red Red - Battery Positive
ET4 original 100 - 130 Ω 300 - 400 Ω 25 - 30v AC 26 - 30v AC 1.5 - 2 amp (charged bat.=13v)
Skipper 2T Red - Brown Green - White n/a Yellow - Yellow
Typhoon 125 90 - 140 Ω 100 - 160 Ω 27 - 30v AC
Leader (all) Green - Black n/a n/a Any yellow - yellow 0.7 - 0.9 Ω
125 / 180 105 - 124 Ω Yellow to earth = no continuity
Hexagon 250 Green / White - Blue / Yellow n/a n/a Any yellow - yellow 0.1 - 1.0 Ω
GT & GTX 50 - 170 Ω Yellow to earth = no continuity
X9 250 White / Yellow - Yellow n/a n/a Any yellow - yellow >< 0.6 Ω
5-3
Test to be carried out with the stator un-plugged and engine stopped.
Test to be carried out with rectifier / regulator disconnected and engine running.
Test to be carried out with rectifier / regulator and battery disconnected.
Test with unit unplugged.
5-4
1of 3
Piaggio Ltd. August 2002
Injected Engines.
Injected engines do not need a choke because the ECU monitors the ambient air temperature and
engine temperature and will apply a suitably rich mixture when needed.
Faults.
The most likely fault is the choke remaining ON. Symptoms will be anything that may be caused by
a rich mixture.
1. High fuel consumption.
2. Black spark plug.
3. Rough running when hot. OK when ridden hard but rough and four stroking at 20 mph.
4. Fails to start. Plug is found to be black and fouled.
Note. Remember that the choke defaults to being ON. If the choke does not turn off the symptom
will be a black and fouled plug. Or; The scooter starts and idles ok and runs at speed ok. When
riding slowly (15 - 20 mph) the engine runs very roughly.
5-4
2of 3
Piaggio Ltd. August 2002
Dia.2. Choke unit power supply.
Choke
DC powered choke
V 1. Ignition off = 0 volts
2. Ignition on = 12 volts
3. Engine run = 13-14.5 volts
Note. Choke units all look much the same but are different and it is important to use the correct
choke in the correct carburettor.
5-4
3of 3
Piaggio Ltd. August 2002
Fuel Gauge & Sender Circuit
Piaggio Ltd 14/10/2003 Piaggio Ltd
Fuel Gauge
Low fuel
FUEL warning
A
C
B
WIRING
A = BLACK
Float B = GREEN / YELLOW
C = GREEN / WHITE
TESTS
A-C
Low fuel level >< 100 ohms
High fuel level >< 3 ohms
5-5
INSTRUMENT PANEL DISPLAY
Several Piaggio vehicles now have electronic instruments. Please make sure you are familiar with
their operation and settings.
B (Beverly)
Clock and trip counter will re-set if voltage drops below 4,5v. Total distance record is “non-
volatile” and can not be affected.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold down the MODE and CLOCK buttons
3. Turn on the ignition
4. Miles or Km will be displayed to show which is selected. Turn off and start again to change it
DNA
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See Service station Manual. Originally the manual said that the
change can only be made if less than 6km show on the total distance. This is no longer true, the
change can be made as often as needed at any distance.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
ICE
Changing Km/h speedo and Km distance to MPH and Miles.
This should be done at PDI. See Service station Manual.
1. Press and hold down the MODE and CLOCK buttons.
2. Turn on the ignition. The display will remain blank.
3. Wait until the display shows the letters “MPH”. Then you can release the buttons.
4. Wait for the instrument to go through the normal start up and you will notice that it now
displays MPH.
Nexus 500
Clock.
The clock time and date functions MUST BE SET AT PDI. Because the service icon
intervals are controlled by time as well as mileage.
5-6
1 of 3
Piaggio Ltd. 25/05/04
Nexus cont.
Service icons.
There are two icons on the display to remind the owner that certain servicing is due. These icons
are controlled by elapsed mileage and elapsed time so it is important to set the date and time
correctly at PDI. If you do not do this you may find the icons come on at the wrong time (and you
will get a grumpy customer).
SERVICE: Comes on after first 1000km and then after every 6000km.
This light also comes on after one year even if the distance has not been covered.
BELT: Comes on after every 12000km.
Don’t forget to reset service icons when you do a service, even if they are not flashing
(scooter has come in early). If you do not do it the customer will be back in a few days with
an icon flashing. That makes you look bad and again you have a grumpy customer.
X9
Clock.
The clock time and date functions MUST BE SET AT PDI. Because some of the service
light intervals are controlled by this.
Service lights.
There are three lights on the display to remind the owner that certain servicing is due. These
lights are controlled by elapsed mileage and elapsed time so it is important to set the date
correctly at PDI. If you do not do this you may find the lights come on at the wrong time (and
you will get a grumpy customer).
OIL: Comes on after first 1000km (625 miles) and then after every 3000km
SERVICE: Comes on after first 1000km and then after every 6000km.
This light also comes on after one year even if the distance has not been covered.
BELT: Comes on after every 18000km.
5-6
2 of 3
Piaggio Ltd. 25/05/04
X9 cont.
Don’t forget to reset service lights when you do a service, even if they are not flashing
(scooter has come in early). If you do not do it the customer will be back in a few days with a
light flashing. That makes you look bad and again you have a grumpy customer.
It is probably worth going through the re-set procedure for all three lights at PDI because if
the battery had been connected previously the counter will have started from the wrong day.
ZIP
The Zip now has electronic instruments. The speedometer is still the traditional analogue
display but it is now electronically controlled. The odometer is now digital LCD. It is
supplied showing the distance in Km. It can be changed to show miles but only if it is
changed during the first 10km. CHANGE IT AT PDI.
Changing the oddometer display to show miles.
1. Ignition off
2. Press and hold the button on top of the leg shield.
3. Turn on ignition. LCD display will show “Cont” (km) or “EnGL” (miles)
4. Briefly press button to toggle between the two alternatives.
5. When the correct press and hold the button for more than one second.
6. Turn ignition off. Turn back on to confirm the setting is now correct.
Re-setting the “Change Oil” warning.
At 6000km an oil change warning will be displayed on the LCD display for 10 seconds every
time the ignition is turned on. Cancel this at service.
1. Press and hold the button at top of the leg shield.
2. Turn ignition on.
3. Release button and turn ignition off. Turn ignition back on to check that the warning has
been cancelled.
5-6
3 of 3
Piaggio Ltd. 25/05/04
Remote Seat Release
Piaggio Ltd 01/02/2006
Replacing the remote control key battery and adding new keys.
Battery is a CR1616
1. Aerial - violet
2. Seat actuator
3. Reset
4. +12v
6. +12v switched
7. Earth - black
10. Trunk actuator
11. Pre-wiring for alarm (X8 & X9)
12. Pre-wiring for alarm (X8 & X9)
5-7
Setting the clock.
Any Piaggio / Gilera / Vespa scooter with a separate two button clock.
A
3 : 29
B
The clock should be displaying the hours and minutes with the two dots flashing.
Press button A once and the month and day will be displayed for about five seconds.
Press and release button B once and the clock will alternately display the day and month and
then the hour and minute.
Press and hold button B and you can set the month by pressing button A repeatedly until the
correct month is displayed. Release button B
Press and hold button B again and you can set the day by pressing button A repeatedly until
the correct day is displayed. Release button B
Press and hold button B again and you can set the hours by pressing button A repeatedly
until the correct hour is displayed. Release button B
Press and hold button B again and you can set the minutes by pressing button A repeatedly
until the correct minutes are displayed. Release button B
Press and release button B again and it will return the display to the normal hours and
minutes.
To return to the normal display at any time repeatedly press button B until the normal display
is shown.
5-8
Piaggio Ltd. 01/02/06
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 16/10/2003 Piaggio Ltd.
Vacuum
tap
Vent
control
Balance pipe
Pump driven by crank valve
case depression Supply to
carburettor
Vent to
atmosphere
One way Pump
valve
Typhoon 80 and 125 have an auxiliary fuel tank located under the front panel. The
plumbing for this fuel system looks complicated. The Typhoon parts catalogue contains a
illustration which should help you locate the components on the vehicle. The diagram
above is intended to help explain the operation of the system and should prove useful when
fault finding.
VENT TO ATMOSPHERE The system has only one vent which you will find exiting under
the rear mudguard.
VENT CONTROL VALVE Controls venting to prevent loss of fuel from full tank. Air can
enter the tank without restriction but a slight pressure is required before vapour can exit.
AUX TANK VENT Auxiliary tank vents to the main tank via a pipe that has to run under the
foot boards. Because this pipe gets lower than the tank level it can become full of fuel and
so the auxiliary tank will not vent. To prevent this a limited flow ONE WAY VALVE allows
any fuel to be sucked out.
A large diameter BALANCE PIPE lets petrol flow between the two tanks.
A smaller diameter pipe passes through the PETROL PUMP which pumps petrol from the
auxiliary tank to the main tank.
Petrol PUMP is driven by the vacuum/pressure pulses from the crank case.
Note that the BALANCE PIPE stands up into the main tank so once the fuel level reaches
that point the pump will drain the auxiliary tank and all the remaining fuel will be in the main
tank. Because of this layout the fuel gauge does not drop at a steady linear rate. If you start
with a full tank, fuel is used in the following three phases:
1. Fuel used from main and auxiliary tanks equally - Gauge will drop from full to ¼ .
2. Level remains constant in main tank while auxiliary is drained - Gauge remains at ¼ .
3. Fuel is used only from main tank - Gauge drops from ¼ to empty.
VACUUM TAP is operated by vacuum from the inlet manifold.
6-1
1 of 2
TYPHOON 80 - 125 FUEL SYSTEM
Piaggio Ltd. 16/10/2003 Piaggio Ltd.
FAULT FINDING
If you suspect that the fault is due to lack of fuel. Firstly prove that the carburettor is
running out of fuel.
Attach a piece of clear tube to the float bowl drain and turn it up the side of the
carburettor.
Open the drain screw. you will now be able to view the fuel level. It should remain about
3.5mm below the float bowl joint. If you find it is low or it drops during running then you
should explore the fuel supply.
If you have a problem that suggests a poor supply of fuel to the carburettor.
1. Check that you have fuel in the main tank. If you have fuel then you can forget about
the front tank and its associated plumbing, this can not affect the supply to the
carburettor.
Not able to get 7 litres of fuel in scooter with a nearly empty tank.
Auxiliary tank is not being used for some reason.
1. Check pump. With engine running you should see the pumped fuel coming out of the
pipe in the main tank.
2. Check for pinched pipes particularly under foot boards and helmet compartment.
3. Check auxiliary tank vent is clear of fuel (one way valve not working).
Scooter runs ok on bench but customer says it cuts out when ridden.
1. Pipe trapped under helmet compartment is squashed by weight of rider.
6-1
2 of 2
DNA FUEL SYSTEM
Piaggio Ltd. 16/10/2003 PAGE 1 OF 2
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
See Note 6.
OVER RUN
VALVE
180 only
VACUUM FROM
FUEL TANK MANIFOLD
VACUUM
TAP
NON
RETURN
VALVE
FUEL FILTER
TANK WHITE PLASTIC
VENT FUEL PUMP
6-2
DNA FUEL SYSTEM
Piaggio Ltd. 16/10/2003 PAGE 2 0F 2
MANIFOLD
VACUUM
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Early 50 NOTES:
1. Carburettor is gravity fed not pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
Later DNA 50
MANIFOLD
VACUUM
VACUUM TAP
METAL BODIED
FUEL PUMP
TANK
VENT
CRANKCASE
PRESSURE /
VACUUM
Later 50 NOTES:
1. Carburettor is pressure fed.
2. Fuel pipes are clear plastic. Vacuum pipes are black rubber.
3. Pump is driven by crankcase vacuum/pressure. Not manifold vacuum
4. Slow running adjustment is "air bleed". Turn in to richen
6-2
HEXAGON EXS1T fuel system.
HEADER TANK
HEADER TANK
VENTING PIPE
MAIN TANK
CARBURETOR
FILTER
PUMP
CRANKCASE
6-3
Piaggio ltd. August 2001
PUMPED FUEL SYSTEMS
Explanation of differences on Piaggio and Gilera scooters
These scooters all have a carburettor and pumped fuel supply:
6-4
1 of 3
Piaggio Ltd. 06/01/06
HEXAGON 2 stroke. All have a pressurised fuel system. Pump operates by
crankcase pressure/vacuum.
EXS1T early. Pump supplies fuel directly to the carburettor.
EXS1T late. Same as early system but with a header tank to ensure a head of fuel
to help starting after a period. The header tank has a return pipe, the connector on
the tank has a very small hole so system pressure is maintained, it is important this
hole is not enlarged.
ZAPM05000 (125). Pump supplies fuel directly to the carburettor.
ZAPM06000 (180). Same as 125 but with a limited flow return that controls the
supply pressure. This is a “T” piece in the carburettor supply pipe and a pipe that
returns to the tank, there is a restrictor in that pipe to limit the return and maintain
the system pressure.
Refer to the separate sheet for a more detailed explanation (Hexagon LX / LXT fuel
system)
6-4
2 of 3
Piaggio Ltd. 06/01/06
VESPA GT 125 / 200 All have a pressurised fuel system.
Pump operates from the inlet manifold vacuum.
Pump is near the tank and supplies fuel directly to the carburettor via an inline fuel
filter and a non return valve.
6-4
3 of 3
Piaggio Ltd. 06/01/06
VESPA PX FUEL TAP
Piaggio Ltd. 16/10/2003 Piaggio Ltd.
CLOSED
OPEN
RESERVE
6-5
FITTING NEW MAIN BEARINGS TO TWO STROKE AUTO’S
Replacing the main bearings is not a difficult job but it MUST be done the correct
way to ensure success.
The problem can be that you do not achieve the correct end float in the crank so
the bearings are being side loaded. This will cause a bearing failure within a very
short time (200 miles max!)
It is vital that the end float is checked with a dial gauge once the cases have
been bolted together.
The following assembly procedure is the best way to do the job. It is the quickest
and easiest. Also it almost guarantees correct tolerance. Please do it this way:
1. Heat the bearings in engine oil. First signs of smoke from the oil is hot enough!
About 100 degrees
2. Support the crankshaft vertically. Drop one bearing onto crank. If it will not drop
on (by gravity) it is not hot enough. If you have to tap it home, ONLY use a
piece of tube to act on the centre race. NEVER hit the outer race. Once it is on
leave it to cool.
3. Turn crank over and drop other bearing on. Leave it to cool completely.
4. Position the drive side crankcase half on its side with inside facing up. Support it
on blocks of wood so the crank can be dropped in (again, just using gravity).
1
1 of 3
Piaggio Ltd. 06/01/04
5. Heat the case with a hot air gun, mostly heat it around the area where the
bearing will fit. Don't try to hurry this. It is hot enough when the rear end of the
case is too hot to keep you hand on.
6. When it is hot enough then drop the crank / bearing in and leave it to cool. If it
will not drop in easily then the case is not hot enough yet.
7. Once it is completely cold turn the case over so the crank is hanging down and
then fit the crank removal tool 20163Y (50cc) or 20262Y (125 & 180cc) as if you
were going to press the crank back out of the case.
8. Tighten the extractor bolt as tight as you can by hand. This will push the crank
out against the bearing so all the free play in the bearing has been removed
and the crank is pushed out as far as it can go. Do not use a spanner to tighten
the bolt or you may move the bearing. Tightening it by hand can not move the
bearing (you ain't that strong). Now put the case back on it’s blocks of wood.
2 of 3
Piaggio Ltd. 06/01/04
9. Heat the other (small) case half and prepare to drop it onto the crank / case.
10. Fit the cases together with liquid gasket (not silicon). Don't forget the water
pump impeller on water cooled engines. Bolt it up and leave it to cool.
11. Once it is completely cold remove the special tool. Now use a dial gauge to
measure the end float. Pull the crank one way, notice the gauge reading and
then push it the other way. You MUST have 0.03 - 0.09mm free play.
12. If you have nearly got the free play try tapping each end of the crank with a
nylon hammer and check again.
13. If you have not got enough free play there is no point carrying on. Take it apart
and do it again (I would recommend using new bearings just in case the others
have been damaged!).
The reason for establishing the end float is to ensure that there is no side load on
the bearings. Ball races do not like side load and they will fail very quickly.
Checking the free play guarantees that the bearing is not side loaded and the
balls can run centrally in the bearing tracks.
Please do not try and improvise. Make sure you have all the correct tools for the
job. They are a very good investment for time saved and stress avoided.
If you have any questions please give your Regional After Sales Manager a call.
3 of 3
Piaggio Ltd. 06/01/04
PX 200 / 125 “COSA” TYPE CLUTCH
The COSA type clutch is now fitted to the PX 200 & PX125.
It can replace the old type clutch as a complete assembly. p/n 433548 (200cc) p/n 288650 (125cc)
NOTE
CHAMFER
Piaggio Ltd. May 2000
PISTONS AND SMALL END BEARINGS
Small End Bearing sizes.
Small end needle roller bearings fitted to two stroke twist and go engines and PX
engines are supplied in four sizes they are colour coded for identification.
The end of the con rod will either be colour coded or it will be marked with a
series of lines.
Piston sizes.
Piaggio use alloy or cast iron barrels on different engines. Alloy barrels can not
be re-bored and over size pistons are not available. Oversize pistons are
available for cast iron barrels. These are listed as 1M, 2M, 3M.
In addition to oversize there will be four pistons listed for all engines as “FC” or
FC1, FC2 etc. These are tolerance fittings.
Pistons can be matched to barrels in two ways. Either by referring to the
tolerance data page near the front of the appropriate Service Station Manual or
by referring to the marking on the crown of the piston and the top of the barrel.
On some engines barrel and piston will both have a letter stamped into them.
Both letters should match. The lowest (first) part number will be the smallest piston
and first in this list.
Remember, if you are measuring barrel and piston you should always measure in
line with the gudgeon pin because they will have worn oval. Most wear occurs
at right angles to the gudgeon pin.
3
Piaggio Ltd. August 2001
Up side down Forks
Piaggio Ltd. 07/08/2002 Typhoon / Runner etc.
Nylon Bush
Upper Circlip
Upper Circlip
Nylon Bush
Lower Circlip
Dust Seal
Tapered groove
Nylon Bush
Fork Leg
Lower Circlip
Fork Stanchion
Forks are grease filled for lubrication. The grease can be expected to work past the nylon bush so the chrome stanchion will get a
dirty ring round it.
Damping is by a sealed hydraulic damper cartridge in the left leg. The cartridge is held at the bottom by a bolt that will be found in the
bottom of the axle mounting. The top of the damper rod is held by a nut on top of the top yoke. If the seals in this unit fail you will find
oil dripping from the bottom of the left leg.
Some 50's did not have the damper. To check if a damper is fitted: look for the nut on top of the left leg, no nut means no damper.
To separate the fork leg:
1. Remove damper top nut (from left leg only).
2. Remove the dust seal.
3. Remove the bottom circlip.
4. Pulling the stanchion hard will force the upper circlip out of the tapered groove, the circlip and bush will be pulled out.
On very early forks the top circlip groove was not tapered so it will be necessary to pull the bush out to get to the circlip.
To pull the bush out:
1. Lubricate the bush with WD40 or similar.
2. Carefully screw two small self tapping screws into the nylon bush and pull it out using two pairs of pliers.
Note that there are several manufactures of these forks and although they look the same the internal components may not be
interchangeable between makes.
4
SPARK PLUGS
PIAGGIO / VESPA mm NGK Champion
B 125 (Beverly) 125 four stroke 0.7-0.8 CR8 EB RG4 HC
B 500 (Beverly) 500 four stroke 0.7-0.8 CR7 EKB RG6 YC
Cosa 125 , 150 0.6 B9 ES (BR9 ES) N2C (RN2C)
Cosa 200 0.6 B7 ES (BR7 ES) N4C (RN4C)
Fly 50 two stroke 0.5-0.6 RGN2C
Fly 125 Leader four stroke 0.8 CR9 EB RG4HC
Free 50 (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon 125 &180 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Hexagon GT250 & GTX 250 (Honda 4 stroke) 0.8-0.9 DPR6 EA9
Hexagon GTX 125 four stroke 0.7-0.8 CR9 EB RG4 HC
Liberty 50 two stroke (all versions) 0.5-0.6 BR9 ES RN2C
Liberty 125 four stroke (original version) 0.7-0.8 CR9 E RG4 HC
Liberty 125 Leader four stroke 0.7-0.8 CR7 EB RG6 YC
Liberty 125 Leader four stroke (heavy use) 0.7-0.8 CR8 EB RG4 HC
Liberty 125 RST (2004>) Leader four stroke
NRG 50 water cooled (heavy use) 0.5-0.6 BR10 ES RN1C
NRG 50 (air or water cooled. All versions) 0.5-0.6 BR9 ES RN2C
Quartz 50 0.5-0.6 BR9 ES RN2C
Sfera 125 four stroke 0.5-0.6 CR9 E RG4 HC
Sfera 50 & Sfera 80 (all versions) 0.5-0.6 BR9 ES RN2C
Skipper ST 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Skipper 125 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Velofax 50 two stroke 0.5-0.6 BR9 ES RN2C
Vespa 50 Special & PK50S 0.6 B6 HS L86
Vespa ET2 50 two stroke (carburettor) 0.5-0.6 BR9 ES RN2C
Vespa ET4 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Vespa ET4 125 four stroke (all versions) 0.7-0.8 CR9 E RG4 HC
Vespa LX 50 four stroke 0.7-0.8 CR8EB
Vespa LX 50 two stroke 0.6-0.7 RGN2C
Vespa LX 125 four stroke 0.7-0.8 CR7EB RG6YC
Vespa GT 125 0.7-0.8 CR8 EB RG4 HC
Vespa GT 200 0.7-0.8 CR7 EB RG6 YC
Vespa GTS 250 injection 0.7-0.8 RG4 PHP
Vespa Primavera ET3 0.6 B7 HS
Vespa Primavera & PK 125 0.6 B6 HS
Vespa PX 125 0.5-0.6 B7 HS L82C
Vespa PX 200 0.5-0.6 B7 ES (BR7 ES) N4C (RN4C)
Vespa T5 Classic 125 0.6 B9ES (BR9 ES) N2C (RN2C)
X9 125 (Piaggio 4 stroke engine) 0.7-0.8 CR8 EB RG4 HC
X9 250 evolution (Piaggio 4 stroke engine with carburettor) 0.7-0.8 CR8 EB RG4 HC
X9 250 (Honda 4 stroke engine) 0.8-0.9 DPR7 EA9
X9 500 (Piaggio 4 stroke engine) 0.7-0.8 CR7 EKB RG6 YC
Zip 50 four stroke 0.7-0.8 CR9 E RG4 HC. RG4 PHP
Zip 50 2 stroke (all versions, inc. catalytic) 0.6-0.7 BR9 ES RN2C
Zip 125 four stroke 0.7-0.8 CR7 EB RG6 YC
GILERA
Coguar 125 (Honda 4 stroke engine) 0.8-0.9 DPR8 EA9
DNA 125 & DNA 180 four stroke 0.7-0.8 CR8 EB
DNA 50 two stroke (catalytic) 0.6-0.7 BR9 ES RN2C
H@K & GSM 50 2 stroke (Gilera engine) 0.5-0.6 BR9 ES RN2C
H@K & GSM 50 2 stroke (Derbi engine) 0.-0.
ICE 50 two stroke catalytic 0.6-0.7 BR9 ES RN2C
Nexus 500 four stroke 0.7-0.8 CR7 EKB RC6 YC
RCR 50 2 stroke (Derbi engine) 0.5 B9 ES (BR9 ES) N2C (RN2C)
Runner VX125 & VXR180 four stroke 0.7-0.8 CR8 EB
Runner VXR 200 four stroke 0.7-0.8 CR7 EKB RG6 YC
Runner 50, 125 & 180 two stroke (all versions) 0.6-0.7 BR9 ES RN2C
Runner 50 “Purejet” direct injection 2 stroke 0.6-0.7 RG6 YCA
Stalker & SKP 50 two stroke 0.5-0.6 BR9 ES RN2C
OLDER GILERA MOTORCYCLES
Saturno 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Dakota 350 / 500 four stroke 0.6-0.7 DPR8 EA9 A5YC
Nordwest 600 four stroke 0.6-0.7 DPR9 EA9
RC 600 four stroke 0.6-0.7 DPR8 EA9
CX 125 & Apache & Crono & Free-Style 125 cc two stroke 0.6-0.7 B10 EG - BR9 EG N82 - C55
GFR 125 two stroke 0.6-0.7 B10 EGV C55C
25/08/05
7-5
7-6 Oil list.xls
Make/Model Engine Gearbox Final Drive Forks Coolant
Vespa ET2 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Vespa ET4 50 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Vespa LX 50 4t 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Vespa ET4 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Vespa LX 125 & ET4 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Vespa GT 125 & GT 200 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16 2.1 - 2.5
Vespa GTS 250 injection 4 str. 5W-40 synthetic API SJ or higher 1.3 ltr. CVT - Gear 75W-80 light gear GL4 or higher 250cc sealed unit - Ethelyne Glycol Cuna NC 956-16 2.1 - 2.5
Vespa PX 125 / 150 / 200 2 str. Synthetic 2 stroke API TC or higher - 4 spd 80W GL4 or higher 250cc n/a - - sealed unit - Air -
Piaggio B 125 & B 125 RST 4 str. 5W-40 synthetic API SJ or higher 1.1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio B 500 4 str. 5W-40 synthetic API SJ or higher 1.7 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 10W 233cc Ethelyne Glycol Cuna NC 956-16 1.7 ltr.
Piaggio Deisis 100 2 str. Hi Scooter 2 Tech - CVT - Gear 80W-90 light gear GL3 or higher 110cc sealed unit - Air -
Piaggio Fly 50 2 str. Synthetic 2 stroke API TC++ or higher 1.2 ltr. CVT - Gear 80W-90 light gear GL3 or higher 85cc 20W 30cc Air -
Piaggio Fly 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 30cc Air -
Piaggio Hexagon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon LX125 / LXT180 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GT 250 4 str. 20W-50 synthetic API SG or higher 800cc CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16 1.82 ltr.
Piaggio Hexagon GTX 125 / 180 (11") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Piaggio Hexagon GTX 125 / 180 (12") 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 10W 102cc Ethelyne Glycol Cuna NC 956-16
Piaggio Liberty 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 30cc Air -
Piaggio Liberty 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 95cc 20W 90cc Air -
Piaggio Liberty 125 Leader 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Air -
Piaggio NRG 50 water cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Ethelyne Glycol Cuna NC 956-16 900cc
Piaggio NRG 50 air cooled models 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Sfera 125 4 str. 20W-50 synthetic API SG or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 90cc sealed unit - Air -
Piaggio Skipper 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Air -
Piaggio Skipper ST 125 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc sealed unit - Air -
Piaggio Typhoon 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 85cc sealed unit - Air -
Piaggio Typhoon 125 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio X8 125 / 200 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 10W 125cc Ethelyne Glycol Cuna NC 956-16 2.1 ltr.
Piaggio X8 250 4 str. 5W-40 synthetic API SJ or higher 1.3 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 10W 133cc Ethelyne Glycol Cuna NC 956-16 2.1 ltr.
Piaggio X9 125 & 125 Evolution 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.2 ltr.
Piaggio X9 250 (Honda engine) 4 str. 20W-50 synthetic API SG or higher 1.1-1.3 CVT - Gear 80W-90 light gear GL3 or higher 200cc 20W 90cc Ethelyne Glycol Cuna NC 956-16
Piaggio X9 250 (Piaggio engine) 2004> 4 str. 5W-40 synthetic API SG or higher 1.3 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 90cc Ethelyne Glycol Cuna NC 956-16 1.8 ltr.
Piaggio X9 500 & 500 Evolution 4 str. 5W-40 synthetic API SJ or higher 1.7 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc 20W 125cc Ethelyne Glycol Cuna NC 956-16 1.8 ltr.
Piaggio Zip 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 20W 25cc Air -
Piaggio Zip 50 4t 4 str. 5W-40 synthetic API SJ or higher 850cc CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 25cc Air -
Piaggio Zip 125 (single sided fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc sealed unit - Air -
Piaggio Zip 125 (telescopic fork) 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 60cc Air -
Gilera Coguar 125 4 str. 20W-50 synthetic API SG or higher 1.2 ltr. 5 spd. integral with engine - Chain - - 10W 280cc Air -
Gilera DNA 125 / 180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera DNA 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 100cc 20W 280cc Ethelyne Glycol Cuna NC 956-16
Gilera GSM / H@K 50 (Gilera engine) 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 500cc Chain - - 10W 200CC Ethelyne Glycol Cuna NC 956-16
Gilera Ice 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 90cc Air -
Gilera Ice 50 (front fork marked "TH") 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc 10W 72cc Air -
Gilera RCR 50 (Paoli forks) 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 650cc Chain - - 10W 285cc Ethelyne Glycol Cuna NC 956-16 0.85 ltr.
Gilera Runner 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner 50 Purejet Direct injection 2 str. Synthetic 2 stroke API TC++ or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Ethelyne Glycol Cuna NC 956-16 0.9 ltr.
Gilera Runner FX125 / FXR180 (early) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc sealed unit - Ethelyne Glycol Cuna NC 956-16
Gilera Runner FX125 / FXR180 (late) 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 80cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera Runner VX125 / VXR180 4 str. 5W-40 synthetic API SJ or higher 1 ltr. CVT - Gear 80W-90 light gear GL3 or higher 150cc 20W 80cc Ethelyne Glycol Cuna NC 956-16
Gilera Nexus 500 4 str. 5W-40 synthetic API SJ or higher 1.7 ltr. CVT - Gear 80W-90 light gear GL3 or higher 250cc Ethelyne Glycol Cuna NC 956-16
Gilera SKP (Stalker) 50 2 str. Synthetic 2 stroke API TC or higher - CVT - Gear 80W-90 light gear GL3 or higher 75cc sealed unit - Air -
Gilera GFR 125 2 str. Synthetic 2 stroke API TC or higher - 6 spd. 80W GL4 or higher 1.3 ltr. Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16
Gilera Saturno 350 / 500 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - ><7.5W 310cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera Nordwest 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 400cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
Gilera RC 600 4 str. 15W-40 synthetic 2.2 ltr. 5 spd. integral with engine - Chain - - 10W 640cc Ethelyne Glycol Cuna NC 956-16 1.3 ltr.
VESPA TYRES & WHEELS
MODEL FRONT REAR
chassis prefix wheel tyre bar wheel tyre Solo-2up
Cosa 2 125 / 200 VNR2T / VSR2T 2.50 x 10 100 / 90 - 10 T 1.5 2.50 x 10 100 / 90 - 10. T 1.75 - 2.0
Vespa ET2 50 two stroke ZAPC16 / ZAPC381 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 50 four stroke ZAPC26 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa ET4 125 four stroke ZAPM04 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 2.50 x 10 130 / 70 - 10, 62L T/L 1.8-2.0
Vespa ET4 Leader 125cc four stroke ZAPM19 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8-2.0
Vespa LX 50 2T ZAPC38101 2.50 x 11 110 / 70 - 11, 45L T/L 1.4 3.00 x 10 120 / 70 - 10, 54L T/L 2.0
Vespa LX 50 4T ZAPC383 2.50 x 11 110 / 70 - 11, 45L T/L 1.4 3.00 x 10 120 / 70 - 10, 54L T/L 2.0
Vespa LX 125 ZAPM441 2.50 x 11 110 / 70 - 11, 45L T/L 1.6 3.00 x 10 120 / 70 - 10, 54L T/L 2.2
Vespa PX 125 VNX2T or ZAPM093 2.10 x 10 3.50 - 10, 51J T 1.25 2.10 x 10 3.50 - 10, 51J T 1.75-2.3
Vespa PX 150 ZAPM09401 2.10 x 10 3.50 - 10, 51J T 1.25 2.10 x 10 3.50 - 10, 51J T 1.75-2.3
Vespa PX 200 VSX1T or ZAPM18 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75-2.3
Vespa GT 125 / 200 four stroke ZAPM311 / ZAPM312 3.00 x 12 120 / 70 - 12, 51P T/L 1.8 3.00 x 12 130 / 70 - 12, 62P T/L 2.2
Vespa GTS 250 ZAPM451 3.00 x 12 120 / 70 - 12, 51P T/L 1.8 3.00 x 12 130 / 70 - 12, 62P T/L 2.2
Vespa T5 Classic VNX5T 2.10 x 10 3.50 - 10, 59J T 1.25 2.10 x 10 3.50 - 10, 59J T 1.75 - 2.3
7-7a
Bold type denotes a current model. This list was last updated on 01 February 2006. Identify a vehicle by its chassis prefix AND model name.
PIAGGIO TYRES & WHEELS
MODEL FRONT REAR
chassis prefix wheel tyre bar wheel tyre Solo-2up
B 125 (Beverly 125) ZAPM281 3.00 x 16 110 / 70 - 16, 52P T/L 2.0 3.50 x 16 140 / 70 - 16, 65P T/L 2.2 - 2.5
B 500 (Beverly 500) ZAPM341 3.00 x 16 110 / 70 - 16, 52S T/L 2.2 4.50 x 14 150 / 70 - 14, 66S T/L 2.5
Diesis 100 (also Diesis 50) ZAPM301 (ZAPC34) 3.00 x 12 120 / 70 - 12, 56J T/L 1.7 3.00 x 12 120 / 70 - 12, 56J T/L 1.9 - 2.1
Fly 50 ZAPC441 3.50 x 12 120 / 70 - 12, 58P T/L 1.8 3.50 x 12 120 / 70 - 12, 58P T/L 2.0 - 2.3
Fly 125 ZAPM421 3.50 x 12 120 / 70 - 12, 58P / 60L T/L 1.8 3.50 x 12 120 / 70 - 12, 58P / 60L T/L 2.0 - 2.3
Free 50 FCS1T & FCS2T 1.85 x 14 80 / 80 - 14, 43J T/L 2.0 1.85 x 14 80 / 80 - 14, 43J T/L 2.5-3.0
Hexagon 125 EXS1T 2.50 x 10 100 / 80 - 10, 58J T/L 1.8 3.00 x 10 130 / 70 - 10, 62J T/L 2.3-2.5
Hexagon GT 250, GTX 250 ZAPM14 3.00 x 11 120 / 70 - 11, 50L T/L 1.8 3.00 x 11 130 / 70 - 11, 60L T/L 2.2-2.5
Hexagon GTX 125 (11 inch wheels) ZAPM20 3.00 x 11 120 / 70 - 11, 50L T/L 1.8 3.50 x 11 130 / 70 - 11, 60L T/L 2.0-2.5
Hexagon GTX 125 (12 inch wheels) ZAPM20 3.50 x 12 120 / 70 - 12, 51L T/L 1.8 3.50 x 12 140 / 60 - 12, 62L T/L 2.0-2.5
Hexagon LX / LXT ZAPM05 / ZAPM06 3.00 x 11 120 / 70 - 11, 50L T/L 1.8 3.50 x 11 130 / 70 - 11, 60L T/L 2.0-2.5
Liberty 125 ZAPM11 / ZAPM22 1.60 x 16 80 / 80 - 16, 46J T/L 1.8 2.50 x 14 110 / 80 - 14, 56J T/L 2.0-2.2
Liberty 125 RST ZAPM381 2.15 x 16 90 / 80 - 16, 51J T/L 2.0 2.75 x 14 110 / 80 - 14, 59J T/L 2.5
Liberty 50 ZAPC15 / ZAPC371 1.60 x 16 70 / 90 - 16, 42J T/L 1.8 2.15 x 11 90 / 80 - 16, 52J T/L 2.0
80 / 80 - 16, 46J (‘98>)
NRG / NRG Mc2 ZAPC04 / ZAPC18 3.50 x 13 130 / 60 - 13, 53J T/L 1.3 3.50 x 13 130 / 60 - 13, 53J T/L 1.8-20
NRG Extreme air / water cooled ZAPC21 / ZAPC22 3.50 x 13 130 / 60 - 13, 53J T/L 1.3 3.50 x 13 130 / 60 - 13, 53J T/L 1.8-20
NRG Mc3 air / water cooled ZAPC21/ZAPC32 3.50 x 13 130 / 60 - 13, 53J T/L 1.3 3.50 x 13 130 / 60 - 13, 53J T/L 1.8-20
NRG Power liquid & air cooled ZAPC451 / ZAPC453 3.00 x 13 120 / 70 - 13, 57L T/L 1.2 3.50 x 13 140 / 60 - 13, 57L T/L 1.9
Quartz 50 NSP1T 2.50 x 10 100 / 80 - 10, 52J T 1.2 2.50 x 10 100 / 80 - 10, 52J T 1.7-2.5
7-7
Sfera 125 four stroke ZAPM01 2.50 x 10 100 / 80 - 10, 52J T/L 1.5 2.50 x 10 130 / 70 - 10, 62J T/L 1.8-2.3
Sfera 50 / 80 NSL1T / NS81T 2.15 x 10 90 / 90 - 10, 50J T/L 2.15 x 10 90 / 90 - 10, 52J T/L
Sfera RST 50 / 80 ZAPC01 / ZAPM03 2.50 x 10 100 / 80 - 10, 52J / 53J T/L 1.5 2.50 x 10 110 / 80 - 10, 58J T/L 1.8-2.3
Skipper 125 CSM1T 2.50 x 10 100 / 80 - 10, 52J T 1.3 2.50 x 10 110 / 80 - 10, 58J T 1.8-2.3
Skipper LX 125 ZAPM12 3.50 x 12 120 / 70 - 12, 51J T/L 1.4 3.50 x 12 130 / 70 - 12, 56L T/L 1.6-1.8
Skipper ST 125 four stroke ZAPM21 3.50 x 12 120 / 70 - 12, 51L T/L 1.4 3.50 x 12 130 / 70 - 12, 56L T/L 1.6-1.8
Typhoon 125 ZAPM02 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 50 / Typhoon 50 RST TEC1T / ZAPC19 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Typhoon 80 TE81T 3.50 x 10 120 / 90 - 10, 56J T/L 1.3 3.50 x 10 120 / 90 - 10, 56J T/L 1.8-2.5
Velofax 50 VTAC02 1.60 x 17 70 / 90 - 17, 43M T/L 2.0 1.85 x 16 80 / 90 - 16, 46M T/L 2.5-3.0
X8 125 / X8 250 ZAPM363 / ZAPM364 3.50 x 14 120 / 70 - 14, 55P T/L 2.3 3.00 x 12 130 / 70 - 12, 62P T/L 2.6
X9 125 ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.1 3.50 x 14 140 / 60 – 14, 64 P T/L 2.3 – 2.5
X9 250 (Honda engine) ZAPM23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 13 140 / 60 - 13, 63P T/L 2.2 - 2.5
X9 250 Evolution (Piaggio engine) ZAPM 23 3.50 x 14 120 / 70 - 14, 55 P T/L 2.1 3.50 x 14 140 / 60 – 14, 64 P T/L 2.3 - 2.5
X9 500 and X9 500 Evolution ZAPM27 3.50 x 14 120 / 70 – 14, 55 S T/L 2.2 3.50 x 14 140 / 70 – 14, 68 S T/L 2.3 – 2.6
X9 500 fitted with dedicated top box > > > > 2.4 > > > 2.3 - 2.6
Zip 50 Cat 2 stroke & 4 stroke ZAPC25 / LBMC25 2.50 x 10 100 / 80 - 10, 53L T/L 1.3 3.00 x 10 120 / 70 - 10, 54L T/L 1.8 - 2.0
Zip 50 two stroke SSL1T 2.15 x 10 90 / 90 - 10, 50J T/L 1.2 2.15 x 10 90 / 90 - 10, 50J T/L 1.7 - 2.5
Zip RST 50 two stroke ZAPC06 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 100 / 80 - 10, 52J T/L 1.8
Zip SP 50 two stroke ZAPC11 2.50 x 10 100 / 80 - 10, 52J T/L 1.4 2.50 x 10 110 / 80 - 10, 52J T/L 1.8
Zip 125 four stroke ZAPM25 2.50 x 10 100 / 80 - 10, 53L T/L 1.6 3.00 x 10 120 / 70 - 10, 54L T/L 2.0
Bold type denotes a current model. This list was last updated on 01 February 2006. Identify a vehicle by its chassis prefix AND model name.
GILERA TYRES & WHEELS
2000 / 2001 / 2002 / 2003 / 2004 / 2005
MODEL FRONT REAR
chassis prefix wheel tyre bar wheel tyre solo-2up
Coguar 125 custom ZAPM17 2.50 x 17 100 / 80 - 17, 52 S T 1.8 3.00 x 17 130 / 70 - 17, 62 T T 2.0-2.2
DNA 125 / 180 four stroke ZAPM26 3.50 x 14 120 / 70 - 14, 55 P T/L 2.0 3.50 x 14 140 / 60 - 14, 64 P T/L 2.2– 2.5
DNA 50 ZAPC27 3.50 x 14 120 / 70 - 14, 55 L T/L 1.8 3.50 x 14 140 / 70 - 14, 62 T/L 2.0
DNA 50 RST ZAPC27 3.00 x 15 120 / 70 - 15, L or 56P T/L 1.8 3.50 x 14 140 / 70 - 14, 62L or 68P T/L 2.0
GSM 50 super motard VTBC08 2.50 x 17 110 / 80 - 17, 52 T T 1.4 3.50 x 17 130 / 70 - 17, 62 T T 1.6
H@K 50 trail bike VTBC08 1.40 x 21 80 / 90 - 21, 48 P T 1.4 1.85 x 18 110 / 80 - 18, 58 P T 1.6
Nexus 500 ZAPM35 3.50 x 15 120 / 70 - 15, 56 H T/L 2.2 4.50 x 14 160 / 60 - 14, 65H T/L 2.5
Ice 50 ZAPC30 3.00 x 10 120 / 90 - 10, 56 J T/L 1.3 3.00 x 10 120 / 90 - 10, 56 J T/l 1.8
RCR 50 trail bike VTHSDR1EB 1.60 x 21 80 / 90 - 21, 48 P T 1.0-1.1 2.15 x 18 110 / 80 - 18, 58P T 1.2-1.3
Runner 50 ZAPC14 / ZAPC362 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner 50 Purejet ZAPC361 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.6 3.50 x 12 130 / 70 - 12, 56L (or J) T/L 1.8
Runner 50 RST & Purejet RST ZAPC461 / 462 3.00 x 14 120 / 70 - 14, 55L T/L 1,7 3.50 x 13 140 x 60 - 13, 57L T/L 2.10
Runner FX125 / FXR180 (rear drum) ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner FX125 / FXR180 DD ZAPM07 / ZAPM08 3.50 x 12 120 / 70 - 12, 51L (or J) T/L 1.4 3.50 x 13 130/60-13, 60 P T/L 1.6-2.2
7-8
Runner VX125 / VXR180 ZAPM24 3.50 x 12 120 / 70 - 12, 51 L T/L 1.4 3.50 x 12 130 / 70 - 12, 56 L T/L 1.6-2.2
Runner VX 125 rst ZAPM461 3.00 x 14 120 / 70 - 14, 55P T/L 1.8 3.50 x 14 140 / 60 - 13, 63P T/L 2.2
Runner VXR200 ZAPM24 3.50 x 12 120 / 70 - 12, 51 P T/L 1.4 3.50 x 12 130 / 70 - 12, 56 P T/L 1.6-2.2
SMT 50 super motard VTHSDR1FB 110 / 80 - 17 T 1.7-1.8 130 / 70 - 17 2.0-2.1
Stalker 50 (previously SKP) ZAPC13 / ZAPC401 3.50 x 10 120 / 90 - 10, 56 J T/L 1.2 3.50 x 10 130 / 90 - 10, 61 J T/L 1.6-2.0
Bold type denotes a current model. This list was last updated on 13 December 2005. Identify a vehicle by its chassis prefix AND model name.
Only the Runner VX / VXR has an immobiliser. Note the symbol on the key that
denotes an immobiliser chip is fitted.
Later Runner FX / FXR keys look the same as the VX / VXR key but they do not have
an immobiliser chip and the symbol is not on the key.
Runner FX / FXR = the shape shown in the picture is 563585 this has been
superseded to 576719 this looks like the VXR key but does not have an immobiliser
chip.
SKP 50 = 574690
ICE 50 = 576719
9
Piaggio Ltd. 04/11/02
SERVICE LIMITS
NEW LIMIT Or change at:
50cc 2T
(Inc. Purejet) Belt - 17.5mm 15,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 20,000 km
Fuel Filter - - 10,000 km (Purejet)
50cc 4T
Oil 850cc 6000 km
Belt - 17.5mm 12,000 km
Rollers 18.9mm 18.5mm -
125cc 2T
Belt - 21.0mm 12,000 km
Rollers - 18.5mm -
Oil Pump Belt - - 30,000 km
125cc 4T orig.
Oil 850cc 5000 km
Belt 17.2mm 10,000 km
Rollers 18.5mm -
125cc Leader.
Oil 1 ltr. 6000 km
Belt 22.5mm 21.5mm 12000 km (check at 6000 km)
Rollers 19.0mm 18.5mm -
B 125 Brake Disks 4.00mm 3.50mm -
180cc 2T
Belt - 20.5mm 12,000 km
Rollers - 19.5mm -
Oil Pump Belt - - 30,000 km
180 / 200cc Leader.
Oil 1 ltr. 6000 km
Belt 20.5mm 19.5mm 12000 km (check at 6000 km)
Rollers 20.6mm 20.0mm -
250cc 4T Hexagon
(Honda engine) Oil 800cc 3000 km
Belt 21mm 18000 km
Rollers 23.8mm 23.2mm -
250cc 4T X9
(Honda engine) Oil 1 ltr. 3000 km
Belt 23.3 22.3 18000 km
Rollers >< 23mm 22.5mm -
500cc Master
Oil 1.7 ltr. 6000 km
Belt 26.2mm 25mm 12000 km
Rollers 24.9mm 24.5mm Check 12000 km
Front Disk 4.00mm 3.50mm -
Rear Disk 5.00mm 4.50mm -
250cc Quasar
Oil 1.3 ltr. 10000 km
Belt 26.2mm 25mm 15000 km
Rollers 24.9mm 24.5mm 10000 km
Front Disk 4.00mm 3.50mm -
Rear Disk 5.00mm 4.50mm -
7-14
Piaggio Ltd. 27/01/06
Restriction Notes
Never discuss the technicalities of how to de-restrict with end users.
Piaggio have never supplied any information about how vehicles are restricted or how to make
them go faster.
Piaggio can not advocate de-restriction for any reason.
Vehicles will only have been homologated as Mopeds so will be technically illegal if they are
de-restricted.
Piaggio have never offered any tuning parts.
If a 50 is de-restricted the licensing requirements will be the same as a 125, so Piaggio’s official
line is “Do not de-restrict, if you want to go faster get a 125”
125cc engines are not restricted, they are designed to produce no more than 11 kw. So they will be
learner legal.
50cc engines are always restricted and are only sold as 45 km/h mopeds. There is no “full power”
option. Most countries in Europe have the same 45 km/h category.
Restriction of 50cc 2 stroke geared engines. H@K & GSM. See Chapter 4 page 2
Only restriction is a restrictor in the inlet end of the exhaust pipe.
A two size larger main jet will be needed. A standard DellOrto part.
If de-restriction is carried out by an authorised dealer, Piaggio are happy that the warranty will not
be affected. Any tuning or fitting of after market parts by the end user or the dealer will affect the
warranty.
7 - 11
1 of 2
50cc Moped restriction information
What is a moped?
A Moped is a two wheel vehicle of no more than 50cc with a design top speed of 45 km/h (28 mph)
All current Piaggio, Vespa and Gilera 50cc two-wheel vehicles are restricted and are only supplied
as Moped’s. They are only tested and homologated as mopeds.
Piaggio do not recommend de-restricting or modifying for any reason.
If the vehicle may be used on a public road. The person carrying out the modification must take full
responsibility for the possible implications of their actions.
If a Moped is de-restricted.
1. It becomes a 50cc Motorcycle.
DVLA should be informed and the vehicle re-registered.
2. It may not conform to motorcycle requirements and may not be legal.
For example; Lighting requirements are different for Mopeds and Motorcycles.
Piaggio can not give any assurance that a de-restricted vehicle will be technically legal.
3. A motorcycle licence will be required.
A 50cc motorcycle has the same licence requirement as a 125cc.
A Motorcycle can not be ridden on a provisional motorcycle licence before basic training is
completed (CBT).
A full car licence allows a moped to be ridden but not a 50cc motorcycle.
4. A rider must be at least 17 years old.
A 16 year old can ride a Moped but not a 50cc Motorcycle.
5. The Insurance company who are insuring the vehicle should be informed.
The premium will probably be un-affected but any modification should be notified to the
insurer in writing. Insurance will be invalid if the vehicle is modified and the insurer not
informed.
Remember that if the vehicle or the rider is not legal then the insurance will be invalid.
6. Piaggio Ltd. Are happy that the warranty will remain valid if the de-restriction is carried out by
an authorised dealer.
If any “tuning” or fitting of non Piaggio parts is carried out then the warranty will be invalid.
Piaggio’s advice has to be: If you want to go faster, get a 125.
Recently a 16 year old was stopped for speeding, when the Police realised his age they immediately
charged him with.
1. Exceeding the speed limit.
2. Riding a motorcycle with no motorcycle licence (he was under age).
3. Riding a motorcycle without valid insurance (insurance is invalid because he is riding illegally).
The dealer who did the de-restriction was charged and found guilty of aiding and abetting!
The boy’s father attempted to sue the dealer!
A disclaimer may be of little use as a defence. Be warned! If someone rides to your shop and asks
you to de-restrict then rides away they will be breaking the law and they have only been able to
break the law because you helped them.
If you get a disclaimer signed one of the conditions should be “I do not intend to use this vehicle on
public roads” and another should be “I am fully aware of the legal implications of having my
vehicle de-restricted and I am prepared to take full responsibility for this”.
7 - 11
2 of 2
PIAGGIO / VESPA / GILERA
CHASSIS NUMBER LOCATION.
Traditional Vespa. PX 125 / 150 / 200. T5 Classic. Etc.
Lift the seat. Remove engine cover (off side) by turning the off side lever near the seat
hinge, outwards. Chassis number is stamped into the chassis near the rear.
Fly 50 / 125, NRG, Skipper, Sfera, Typhoon, Zip. Gilera Runner & SKP (Stalker).
Chassis number is stamped into a plate on the off side below the foot boards. You do
not need to remove anything, just look under the scooter.
Ice 50
Remove the black central cover over the oil tank filler. The Chassis number is stamped
into the main chassis tube on the off side just below the oil filler cap.
Liberty, Free
Chassis number is stamped onto a plate attached to the frame on the off side above
the cooling fan cover.
Velofax
Chassis number is stamped into the underside of the rear carrier (part of the frame).
X9 125, 180, 250 & 500. B 125, 200 & 500. Nexus 500, X8 125 / 250.
Lift seat. Pull up the internal carpet at the rear. Remove the small panel in the floor
toward the rear. Chassis number is directly below.
DNA, H@K, GSM, RCR, Coguar and older Gilera motorcycles, Nordwest, GFR etc.
The chassis number is stamped into the right hand side (off side) of the head stock.
A duplicate of the chassis number will not be found in any other location. If the number has
been removed it will not be possible to identify the vehicle.
7-12
Piaggio Ltd. February 2006
QUICK REFERENCE GUIDE
FIRST SERVICE is always at 1000 km (625 miles)
If details here contradict the Service Station Manual you should trust this information.
7-13
1 of 4 Piaggio Ltd. 27/01/06
125 / 180 2t Water cooled. 50 2t Velofax.
Service: 5000 km (12 mths) Service: 4000 km (12mths)
Hub Oil: 80cc - 80w90 light gear oil Hub Oil: fill to level (48cc?)
Spark Plug: 0.6 - 0.7 mm 80w90 light gear oil
Champion RN2C Spark Plug: 0.5 - 0.6 mm
NGK BR9 ES Champion RN2C
Belt Change: width 20.5mm min - 180 NGK BR9 ES
width 21mm min - 125 Belt width: not quoted
12,000 km (24 mths) Roller dia: not quoted
Oil pump belt: 20,000 km (36 mths) Oil pump belt: 20,000 km (36 mths)
7-13
2 of 4 Piaggio Ltd. 27/01/06
125 4t Coguar. Honda XL125 engine 100 2t. Diesis. Derbi engine
Check oil level with dipstick screwed OUT. Service: 5000 km (12 mths)
Engine Oil: 1.2 ltr. 20w50 synthetic SG Hub Oil: 110cc - 80w90 light gear oil
Oil change: 3000 km Spark Plug: 0.6 - 0.7 mm
Service: 6000 km Champion RN2C
Tappets: in:0.10 mm. ex: 0.10 mm NGK BR9 ES
Ign. Timing: 15° @ 1400. 32° @ 3450 Belt change: min width = 16mm
Idle: 1400 rpm. 5000 km (12 mths)
Slow running: 2 turns out (out to richen) Then every 10,000 km
CO: 5% + 0.5%
Spark Plug: 0.8 - 0.9 mm
NGK DPR8 EA9
Chain size:
7-13
3 of 4 Piaggio Ltd. 27/01/06
250 4T QUASAR (carburettor) 250 4T QUASAR (injection)
Check oil level with dipstick screwed IN Check oil level with dipstick screwed IN
Engine Oil: 1.3 ltr 5w40 synthetic SJ Engine Oil: 1.3 ltr 5w40 synthetic SJ
Oil change: 10000 km Oil change: 10,000 km (check @ 5000 km)
Service: 10000 km (12mths) Service: 10,000 km
Rear Hub: 150cc 80/90 light gear oil (X9) Rear Hub: 250cc 75/85 light gear oil GL4
Coolant: 1.2 ltr. 50 / 50 mix Coolant: 2.1 ltr. 50 / 50 mix
Tappets: in: 0.10mm. ex: 0.15 mm Tappets: in: 0.10mm. ex: 0.15 mm
Idle: 1650 rpm. + 50 rpm. Idle: 1650 rpm. + 50 rpm.
CO: 3.8 + 0.7 @1650 rpm CO: N/A
(with SAS valve closed) Spark Plug: 0.7 - 0.8 mm
Spark Plug: 0.7 - 0.8 mm Champion RG4 PHP
Champion RG4 HC NGK ?
NGK CR8 EB Rollers wear limit: 20 mm min.dia.
Rollers wear limit: 20 mm min.dia. Belt wear limit: 19.5 mm min width.
Belt wear limit: 19.5 mm width. Belt Change: 15,000 km.
Belt Change: 12,000 km or 24 mth. Air Filter clean: 10,000 km
Air Filter: Clean at service
If there is ever any doubt about service intervals for a vehicle, always use the intervals shown in
the owners handbook.
Piaggio recommend fully synthetic oil for all engine applications.
Older engines used variator rollers that needed greasing. Later greaseless rollers can be fitted to
early variators. If greased rollers are used lubricate sparingly at every service (except first): Use
only “Jota” grease p.n. 494643
Piaggio have never offered any tuning parts for any vehicles and we will never recommend
tuning or de-restricting a vehicle for any reason.
All 50cc vehicles are only available as “mopeds” restricted to 45 kmh (28mph).
All current 125cc vehicles are “Learner Legal” producing less than 15 hp (11kw). They are not
restricted. If they are tuned they will not be learner legal and warranty will be affected.
7-13
4 of 4 Piaggio Ltd. 27/01/06
KEYS.
All Leader engined vehicles with immobilisers
Notes:
Only the Service key should be used day to day. The Master key should be kept
safely at home.
Use the Service key for testing and fault finding. Only use the Master key for
programming.
It is not possible to programme a replacement master key to a previously
programmed immobiliser.
It is possible to programme new Service keys only if you have the original Master
key.
Original Service keys with a chip fitted can be recognised by this symbol
etched into the metal near the top.
Keys Galore – London – 020 7586 9741 First Access – Herts - 0115 967 6466
Express Keys – Kent – 01689 850008 Auto Keys – London – 020 7586 9741
10
Piaggio Ltd. 04/11/02
Schematic wiring diagrams
Lights section
4-7A
Schematic wiring diagrams
Ignition section
4-6A
X9 500 Stand Circuit
Piaggio Ltd. 30/01/2006
CENTRE
STAND
1 SIDE
STAND WHEEL
WARNING WARNING DIGITAL REVOLUTION
DIGITAL
LIGHT LIGHT INSTRUMENT SENSOR
INSTRUMENTS
PANEL
GREY / BLACK
STOP STAND
7.5 amp OPERATING
RUN
GREEN / BLACK
In battery BUTTON
GREEN / BLACK
compartment
UP
YELLOW / GREEN GREY 8 BLACK
WHITE
DIODE
SIDE STAND 12 Lt. BLUE
SWITCH
16 GREY
YELLOW / GREEN
ORANGE /BLUE
ORANGE
BLUE / GREY 14 ORANGE
STAND LIMIT 15 GREEN
SWITCHES
11 YELLOW
DIODE
WHITE
1 VIOLET
FRONT REAR STARTER
STOP STOP BUTTON
ENGINE STARTER
RED STOP RELAY
9 10 11 12 13 14 15 16
ORANGE ORANGE / WHITE 1 2 3 4 5 6 7 8
85 86 GREY 86 85
YELLOW VIOLET
RED
RED
YELLOW
RED / BLACK
YELLOW 30 amp 70 amp ? amp
In Battery
YELLOW Compartment In Battery
Compartment
RED
~ ~ ~ + +
RECTIFIER / REGULATOR
BATTERY
YELLOW 12v 14ah
WHITE
BLACK MAIN POWER
BLUE
OFF IGNITION RELAY
VIOLET SWITCH
ORANGE / BLUE 30 87
RUN
RED / YELLOW
Under seat
RED / BLACK
VIOLET
There are two DIODES situated under the front cover above the headlight unit. They are together in black heat shrink tubing
There is a single DIODE in the grey wire.
8-3
Nexus 500 Instrument connection
Piaggio Ltd 30/01/2006
You may find an incorrect wiring diagram, with wiring that does not match the vehicle.
This diagram should match the vehicle.
Remote mode push button. Grey. 14 17. Brown / White. Injector LED.
12v + switched live. Yellow / Red. 13 18. Blue. Turn switch right.
Immobiliser LED. Grey / Yellow. 12 19. Pink / Black. Turn switch left.
12v + permanent live. Red / Black. 11 20. Brown / Black. Hazard lights switch
INSTRUMENT PANEL
MULTI PIN CONNECTOR
Looking into the
connector on the
back of the panel
Wheel speed sensor signal. Lt Blue 2. 9. White / Blue. Right turn signal.
Wheel sensor earth. Grey / Black 3. 8. Pink / White. Oil pressure switch +.
RPM signal (to ECU pin 3). Green 5. 6. Orange. Coolant temperature sensor.
Oil Pressure.
Live feed to switch. Switch shorts to earth to light the bulb.
Fuel Gauge.
Live feed to unit in tank. The tank unit shorts it to earth via a variable resistor.
If the gauge is not working.
Un-plug the instruments put a meter between white / green and black.
Low resistance = full tank. High resistance = empty tank.
This has checked the wiring and tank unit.
8-4
Tech Tips. #1 / 2004
1. H@K and GSM fork oil.
Front forks on H@K and GSM need 200cc of 10W fork oil in each leg.
Ref. Mario
2. B 125 Transmission Cover.
It is possible to remove the transmission cover from a B 125 with the engine in
the frame. Oh yes it is, say Garozzo M/C of Sidcup.
Remove the cover screws and clutch shaft centre nut as usual. It is now
possible to get the cover out far enough to remove the clutch drum. Once
the clutch drum is removed it is possible to remove the cover.
Ref. Garozzo M/C
3. X9 500 Tappet adjustment.
It is possible to check / adjust the tappets on an X9 500 with the engine in
the frame.
Remove r/h foot board / body work.
Remove the foot board mounting frame (3 x 6mm bolts)
Place a bar or piece of wood under the rear wheel.
Take out the top mounting bolt from the right hand rear shock absorber.
Then push it forward, pull to one side slightly and pull it as far back as
possible.
Take out the bottom mounting bolt from the left-hand rear shock
absorber. Then push it back as far as possible.
You can now raise the rear of the engine high enough to allow access to
the rocker box cover and then the tappets. Use a length of wood under
the rear tyre as a lever to raise the engine and them block the engine
securely.
Ref. Adam
4. 50cc Indicators.
If you find a fairly new 50cc with indicators that flash normally with engine off
but become fast or erratic when the engine is running you should also find
that a non-resistor plug cap is fitted.
Fitting a resistor cap should cure the problem.
Please note that they do not all have this problem so do not change the
cap unless you have the fault.
Ref. Tech Support
5. Pure jet fault code.
The diagnostic fault code list in the service station manual includes G50
P0250. This code should be G50P0251.
Ref. Mario
6. 2004 Colour Codes.
New colours for 2004 and their associated last two digits of the painted item
part numbers.
5. De-restricting 50's
As you should know, Piaggio do not recommend de-restricting a 50 for any reason but we
know that they do get de-restricted and if you are going to do it we would sooner that you did it
correctly to avoid any problems.
If you do de-restrict please be aware of the legal implications and make your customer aware!
In addition, it is worth fitting lighter rollers and blanking off the secondary air system.
The roller weight has no affect on top speed but initial acceleration will not be very good with
the heavier rollers because it will get into high gear too quickly.
The secondary air system has nothing to do with performance but the reed valve may fail on
the higher power engine because the pulses it is subjected too are much greater, blank it off to
improve long term reliability.
We are aware that the NRG Power DT (air cooled) does not go much faster when de-restricted.
We don't know why at the moment. Italy is investigating.
David Champion
Technical Services
Tech Tips #5
Walbro CV carburettors on four stroke engines.
The carburettor fitted to many of Piaggio's four stroke engines is made by Walbro. This has a black
plastic arm on the side that is moved by a cam on the throttle cable fitting. The arm operates the
accelerator pump that injects extra petrol as the throttle comes off idle to help the engine pick up
crisply.
If the arm's pivot becomes corroded the arm may stick and then the pump will not operate.
Lack of the accelerator pump will show up as a reluctance to rev up quickly and a possibility of
cutting out if the throttle is opened rapidly.
It is worth spraying this pivot with lubricant at ever service.
If you take the reading from the exhaust pipe take off point:
1.25% + 0.25%
Note. If the figure at the tail pipe is not about half that at the exhaust pipe this indicates a blocked
catalytic converter.
50cc 4 Stroke.
If you find a 50cc 4 stroke engine that feels slow at full throttle but is better at three quarter throttle
it needs a larger main jet.
Original jet is # 75
#78 main jet part number: CM142103
SETTING THE CLOCK.
A
3 : 29 B
The clock should be displaying the hours and minutes with the two dots flashing.
Press button A once and the month and day will be displayed for about five seconds.
Press and release button B once and the clock will alternately display the day and month and
then the hour and minute etc.
Press and hold button B and you can set the month by pressing button A repeatedly until the
correct month is displayed. Release button B
Press and hold button B again and you can set the day by pressing button A repeatedly until
the correct day is displayed. Release button B
Press and hold button B again and you can set the hours by pressing button A repeatedly until
the correct hour is displayed. Release button B
Press and hold button B again and you can set the minutes by pressing button A repeatedly
until the correct minutes are displayed. Release button B
Press and release button B again and it will return the display to the normal hours and minutes.
To return to the normal display at any time repeatedly press button B until the normal display is
shown.
LEADER / QUASAR Engine Special Tool
Current LEADER engines have a modified cam chain cover. Early engines had a cast aluminium
cover retained by three screws.
Current engines have a pressed metal cover, which is a push fit (QUASAR engines all have this
system).
The two seals are bonded to this cover.
The cover should be changed every time it is removed.
A special tool (020622Y) must be used when removing and fitting the cover.
The later cover can be fitted to early engines without modification.
If you fit a new variator to an early engine you will have to fit the new type cover.
Below is the explanation of how to use the tool taken from the on line Service Station Manual.
INTERESTING FAULT FINDING.
Here are a couple of recent cases that were solved quickly because the mechanic adopted a
logical approach to fault finding.