Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 83 views

    CUCM IP Address Change

    Uploaded by

    전승원
    This document provides steps to change the IP address of a Cisco Unified Communications Manager (CUCM) Publisher, which includes accessing the CM administration page to change the IP address, updating gateway and interface settings through the CLI, rebooting, and verifying the new IP address is updated everywhere. The steps are: 1) access CM admin page and change IP address, 2) update gateway through CLI, 3) reboot, 4) update interface IP through CLI, 5) reboot, 6) verify new IP through CLI, reports, and configuration.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    CUCM IP Address Change

    Uploaded by

    전승원
    83 views6 pages
    This document provides steps to change the IP address of a Cisco Unified Communications Manager (CUCM) Publisher, which includes accessing the CM administration page to change the IP address, updating gateway and interface settings through the CLI, rebooting, and verifying the new IP address is updated everywhere. The steps are: 1) access CM admin page and change IP address, 2) update gateway through CLI, 3) reboot, 4) update interface IP through CLI, 5) reboot, 6) verify new IP through CLI, reports, and configuration.

    Original Description:

    CUCM IP Address Change

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides steps to change the IP address of a Cisco Unified Communications Manager (CUCM) Publisher, which includes accessing the CM administration page to change the IP address, updating gateway and interface settings through the CLI, rebooting, and verifying the new IP address is updated everywhere. The steps are: 1) access CM admin page and change IP address, 2) update gateway through CLI, 3) reboot, 4) update interface IP through CLI, 5) reboot, 6) verify new IP through CLI, reports, and configuration.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    83 views6 pages

    CUCM IP Address Change

    Uploaded by

    전승원
    This document provides steps to change the IP address of a Cisco Unified Communications Manager (CUCM) Publisher, which includes accessing the CM administration page to change the IP address, updating gateway and interface settings through the CLI, rebooting, and verifying the new IP address is updated everywhere. The steps are: 1) access CM admin page and change IP address, 2) update gateway through CLI, 3) reboot, 4) update interface IP through CLI, 5) reboot, 6) verify new IP through CLI, reports, and configuration.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    CUCM IP Address Change

    Document ID: 116292 Contributed by William Ryan Bennett and Thomas Runyan, Cisco TAC Engineers. Jul 22, 2013

    Contents
    Introduction Prerequisites Requirements Components Used Steps to Change the IP Address

    Introduction
    This document describes how to change the IP address of a Cisco Unified Communications Manager (CUCM) Publisher.

    Prerequisites
    Requirements
    There are no specific requirements for this document.

    Components Used
    The information in this document is based on these software and hardware versions: CUCM Versions 7.1+ Through 8.6.2 No Domain Name System (DNS) Configuration The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

    Steps to Change the IP Address


    Note: Refer to the CUCM 9.x+ and ELM License Upgrade and Installation article for more information. 1. Access the Communications Manager (CM) Administration web page. Use the dropdown menu in order to choose System > Server. 2. Click the Find button and choose the Publisher.

    3. Enter the new IP address in the Host Name / IP Address field.

    4. Click OK and wait for the page to refresh.

    5. Navigate to the CLI and enter set network gateway <IP Address of new GW> at the admin prompt.

    6. Perform reboots and restarts as required when prompted. 7. Navigate to the CLI and enter set network ip eth0 <New IP Address> <New Subnet Mask> at the admin prompt.

    8. Perform reboots and restarts as required when prompted. 9. Wait approximately 15 to 20 minutes for everything to reboot and come back up. 10. Log in to the CLI and the console GUI with the new IP address. 11. Enter show network cluster in the CLI window and verify that the new address is listed.

    12. Open the Unified Reporting tool and use the Unified CM Database Status menu item in order to verify the settings. Ensure that you click Generate New Report every time that you use this page.

    13. Verify that the new IP address appears everywhere it should in order to ensure that the IP address change is successful.

    Updated: Jul 22, 2013

    Document ID: 116292

    You might also like