Electronic Diesel Control EDC 2001

ISBN-3-934584-47-0 The Bosch Yellow Jackets Edition 2001 Technical Instruction Diesel-Engine Management Order Number 1987722135 AA/PDI-08.
01-En
2001
The Program Order Number ISBN
Automotive electrics/Automotive electronics
Batteries 1 987 722 153 3-934584-21-7
Alternators 1 987 722 156 3-934584-22-5
Starting Systems 1 987 722 170 3-934584-23-3
Lighting Technology 1 987 722 176 3-934584-24-1
Electrical Symbols and Circuit Diagrams 1 987 722 169 3-934584-20-9
Safety, Comfort and Convenience Systems 1 987 722 150 3-934584-25-X
Diesel-Engine Management
Diesel Fuel-Injection: an Overview 1 987 722 104 3-934584-35-7
Electronic Diesel Control EDC 1 987 722 135 3-934584-47-0
Diesel Accumulator Fuel-Injection System
Common Rail CR 1 987 722 175 3-934584-40-3
Diesel Fuel-Injection Systems
Unit Injector System/Unit Pump System 1 987 722 179 3-934584-41-1
Radial-Piston Distributor
Fuel-Injection Pumps Type VR 1 987 722 174 3-934584-39-X
Diesel Distributor-Type
Fuel-Injection Pumps VE 1 987 722 164 3-934584-38-1
Diesel In-Line Fuel-Injection Pumps PE 1 987 722 162 3-934584-36-5
Governors for Diesel In-Line
Fuel-Injection Pumps 1 987 722 163 3-934584-37-3
Gasoline-Engine Management
Emission Control (for Gasoline Engines) 1 987 722 102 3-934584-26-8
Gasoline Fuel-Injection System K-Jetronic 1 987 722 159 3-934584-27-6
Gasoline Fuel-Injection System KE-Jetronic 1 987 722 101 3-934584-28-4
Gasoline Fuel-Injection System L-Jetronic 1 987 722 160 3-934584-29-2
Gasoline Fuel-Injection
System Mono-Jetronic 1 987 722 105 3-934584-30-6
Spark Plugs 1 987 722 155 3-934584-32-2
Ignition 1 987 722 154 3-934584-31-4
M-Motronic Engine Management 1 987 722 161 3-934584-33-0
ME-Motronic Engine Management 1 987 722 178 3-934584-34-9
Gasoline-Engine Management:
Basics and Components 1 987 722 136 3-934584-48-9
Driving and Road-Safety Systems
Conventional Braking Systems 1 987 722 157 3-934584-42-X
Brake Systems for Passenger Cars 1 987 722 103 3-934584-43-8
ESP Electronic Stability Program 1 987 722 177 3-934584-44-6
Compressed-Air Systems for
Commercial Vehicles (1):
Systems and Schematic Diagrams 1 987 722 165 3-934584-45-4
Compressed-Air Systems for
Commercial Vehicles (2): Equipment 1 987 722 166 3-934584-46-2
Electronic
Diesel Control EDC
Automotive Technology
T
e
c
h
n
i
c
a
l

I
n
s
t
r
u
c
t
i
o
n
E
l
e
c
t
r
o
n
i
c

D
i
e
s
e
l

C
o
n
t
r
o
l

E
D
C
T
h
e

B
o
s
c
h

Y
e
l
l
o
w

J
a
c
k
e
t
s
Lambda closed-loop control for passenger-car diesel engines
Functional description
Triggering signals
Published by:
Robert Bosch GmbH, 2001
Postfach 30 02 20,
D-70442 Stuttgart.
Automotive Aftermarket Business Sector,
Department AA/PDI2.
Product-marketing, software products,
technical publications.
Editor-in-Chief:
Dipl.-Ing. (FH) Horst Bauer.
Editors:
Dipl.-Ing. (BA) Jrgen Crepin,
Dipl.-Ing. Karl-Heinz Dietsche.
Authors:
Dipl.-Ing. Joachim Berger
(Sensors),
Dipl.-Ing. Johannes Feger
(VE-EDC),
Dipl.-Ing. Lutz-Martin Fink
(Open and closed-loop control),
Dipl.-Ing. Wolfram Gerwing
(Lambda closed-loop control),
Dipl.-Ing. Martin Grosser
(Common Rail System),
Dipl.-Inform. Michael Heinzelmann
(UIS, UPS),
Dipl.-Math. techn. Bernd Illg
(Diagnosis, open and closed-loop control),
Dipl.-Ing. (FH) Joachim Kurz
(VP30, VP44),
Dipl.-Ing. Felix Landhuer
(In-line injection pumps)
Dipl.-Ing. Rainer Mayer
(Torque-controlled EDC systems),
Dr. rer. nat. Dietmar Ottenbacher
(VP30, VP44),
Dipl.-Ing. Werner Pape
(Actuators),
Dr. Ing. Michael Walther
(Data transfer),
Dipl.-Ing. (FH) Andreas Werner
(Common Rail System),
in cooperation with the responsible technical
departments of Robert Bosch GmbH.
Translation:
Peter Girling.
Unless otherwise stated, the above are all em-
ployees of Robert Bosch GmbH, Stuttgart.
Reproduction, duplication, and translation of this
publication, including excerpts therefrom, is only
to ensue with our previous written consent and
with particulars of source.
Illustrations, descriptions, schematic diagrams,
and other data only serve for explanatory pur-
poses, and for presentation of the text. They
cannot be used as the basis for design, installa-
tion, and scope of delivery. We undertake no lia-
bility for conformity of the contents with national
or local regulations.
Robert Bosch GmbH is exempt from liability,
and reserves the right to make changes at any
time.
Printed in Germany.
Imprim en Allemagne.
1
st
Edition, February 2001.
English translation of the German edition
dated: August 2001.
(1.0)
Imprint
Robert Bosch GmbH
Electronic
Diesel Control EDC
Bosch
Robert Bosch GmbH
4 Diesel fuel-injection systems:
An overview
4 Technical requirements
6 Designs
12 Electronic diesel control EDC
12 Technical requirements,
system overview
13 System blocks
14 In-line injection pumps
15 Port-and-helix-controlled axial-pis-
ton distributor pumps
16 Solenoid-valve-controlled axial-pis-
ton and radial-piston distributor
pumps
17 Common Rail System (CRS)
18 Unit Injector System (UIS) for pas-
senger cars
19 Unit Injector System (UIS) and
Unit Pump System (UPS) for com-
mercial vehicles
20 Sensors
21 Temperature sensors
22 Micromechanical pressure sensors
25 Rail-pressure sensors
26 Inductive engine-speed (rpm)
sensors
27 Rotational-speed (rpm) sensors
and incremental angle-of-rotation
sensors
28 Hall-effect phase sensors
30 Half-differential short-circuiting-ring
sensors
31 Nozzle holders with needle-motion
sensor
32 Accelerator-pedal sensors
34 Hot-film air-mass meter HFM5
36 Planar broad-band Lambda oxygen
sensors
38 Electronic Control Unit (ECU)
38 Operating conditions, design and
construction, data processing
44 Open and closed-loop electronic
control
44 Open and closed-loop electronic
control, data processing (DP)
46 Data exchange with other systems
48 Diesel-injection control
57 Lambda closed-loop control for
passenger-car diesel engines
63 Further special adaptations
63 Port-and-helix-controlled injection
systems: Triggering
66 Solenoid-valve-controlled injection
systems: Triggering
73 Control and triggering of the re-
maining actuators
74 Substitute functions
75 Torque-controlled EDC systems
78 Electronic diagnosis
78 Operating concept
81 On-Board Diagnostics (OBD)
82 Data transfer between electronic
systems
82 System overview, serial data trans-
fer (CAN)
87 Prospects
88 Actuators
88 Electropneumatic transducers
89 Continuous-operation braking sys-
tems, engine-fan control
90 Start-assist systems
92 Index of technical terms
92 Technical terms
94 Abbreviations
Contents
Robert Bosch GmbH
Electronics is coming more and more to the forefront in the control and management
of the diesel engine, whereby the question is often raised Is it really necessary to fill
the vehicle with so much electronics ?
The point is though, without electronics it would be impossible to detect a large
number of important variables, such as engine speed, quickly enough for them to be
used for engine management. Electronic control is behind the modern diesel engine
having become more powerful, more efficient, quieter, cleaner, and more economical.
These facts hold true irrespective of the engines operating range or mode.
Electronic Diesel Control, EDC, permits the implementation of such auxiliary func-
tions as smooth-running control (SRC).
EDC is applied for all modern diesel injection systems:
In-line injection pumps, PE,
Distributor injection pumps, VE, VR,
Unit Injector System, UIS,
Unit Pump System, UPS,
Common Rail System, CRS.
Although these injection systems differ in many respects, and are installed in a wide
variety of different vehicles, they are all equipped with a similar form of EDC.
This Technical Instruction manual describes the Electronic Diesel Control and all
its components. The differences between the individual injection systems are shown in
tabular form (Pages 12 through 17). The manual thus provides the reader with a com-
prehensive overview of the various diesel fuel-injection systems from the point of view
of their open and closed-loop electronic control.
Robert Bosch GmbH
Diesel engines are characterized by their
high levels of economic efficiency. Since the
first series-production injection pumps
were introduced by Bosch in 1927, injec-
tion-system developments have continued
unceasingly.
Diesel engines are employed in a wide range
of different versions (Figure 1 and Table 1),
for example as:
The drive for mobile electric generators
(up to approx. 10 kW/cylinder),
High-speed engines for passenger cars
and light commercial vehicles
Engines for construction, agricultural,
and forestry machinery
Engines for heavy trucks, buses, and trac-
tors (up to approx. 80 kW/cylinder),
Stationary engines, for instance as used in
emergency generating sets
Engines for locomotives and ships
(up to 1,000 kW/cylinder).
Technical requirements
In line with the severe regulations coming into
force to govern exhaust and noise emissions,
and the demand for lower fuel consumption,
increasingly stringent demands are being
made on the diesel engine's injection system.
Basically speaking, depending on the partic-
ular diesel combustion process (direct or in-
direct injection), in order to ensure efficient
A/F mixture formation the injection system
must inject the fuel into the diesel engines
combustion chamber at a very high pressure
(today, this is between 350 and 2,050 bar),
and the injected fuel quantity must be me-
tered with extreme accuracy. With the diesel
engine, load and speed control must take
place using the injected fuel quantity with-
out intake-air throttling.
For diesel injection systems, the mechanical
(flyweight) governor is increasingly being
superseded by the Electronic Diesel Control
(EDC). In the passenger-car and commer-
cial-vehicle sector, the new diesel fuel-injec-
tion systems are all EDC-controlled.
4 Diesel fuel-injection systems: An overview Technical requirements
Diesel fuel-injection systems: An overview
Figure 1
M, MW,
A, P, H,
ZWM,
CW In-line injection
pumps in order of
increasing size;
PF Single-plunger in-
jection pumps
VE Axial-piston
distributor injection
pumps
VR Radial-piston dis-
tributor injection
pumps
UPS Unit Pump System
UIS Unit Injector
System
CR Common Rail
System
ZWM
PF
UIS
UPS
CR
M
PF
VE
VR
MW MW MW MW CW
PF(R)
CW
M
PF
VE
VR
UIS
CR
M
PF
VE
VR
UIS
CR
A/P
PF
VE
VR
UIS
UPS
CR
P/H
PF
VE
VR
UIS
UPS
CR
ZWM
PF
VE
UPS
CR
PF(R)
Bosch diesel fuel-injection systems. Areas of application 1
U
M
K
1
5
6
3
-
1
Y
Robert Bosch GmbH
Diesel fuel-injection systems: An overview Technical requirements 5
Table 1
1 Stationary engines,
building and con-
struction machines,
agricultural and
forestry machines
2 With two ECUs,
larger numbers of
cylinders are possi-
ble
2a As from EDC16: 6
cylinders
3 1
st
generation
4 Pilot injection (PI) up
to 90 cks before
TDC; post injection
(POI) possible
5 Up to 5,500 min
1
during overrun
6 2
nd
generation
7 Pilot injection (PI)
possible up to 90
cks before TDC;
post injection (POI)
up to 210 after TDC
8 Pilot injection (PI) up
to 30 cks before
TDC; post injection
(POI) possible
The most important diesel-engine high-pressure fuel-injection systems: Properties and characteristic data 1
Fuel-injection system Fuel injection Application Engine-related data
P
P
a
s
s
e
n
g
e
r

c
a
r
s

a
n
d

l
i
g
h
t

t
r
u
c
k
s
N
C
o
m
m
.

v
e
h
s
.

&

b
u
s
e
s
O
O
f
f
-
H
i
g
h
w
a
y

1
S
S
h
i
p
s
/
L
o
c
o
m
o
t
i
v
e
s
Type
In-line injection pumps
M P 60 550 m, e IDI 4... 6 5000 20
A O 120 750 m DI/IDI 2... 12 2800 27
MW P, O 150 1100 m DI 4... 8 2600 36
P3000 N, O 250 950 m, e DI 4... 12 2600 45
P7100 N, O 250 1200 m, e DI 4... 12 2500 55
P8000 N, O 250 1300 m, e DI 6... 12 2500 55
P8500 N, O 250 1300 m, e DI 4... 12 2500 55
H1 N 240 1300 e DI 6... 8 2400 55
H1000 N 250 1350 e DI 5... 8 2200 70
ZWM S 900 850 m DI/IDI 6... 12 1500 150
CW S 1500 1000 m DI/IDI 6... 10 1600 260
bar
mm
3
(0.1 MPa) min
1
kW
I
n
j
e
c
t
e
d

f
u
e
l

q
u
a
n
t
i
t
y

p
e
r

s
t
r
o
k
e
M
a
x
.

p
e
r
m
i
s
s
i
b
l
e
n
o
z
z
l
e

p
r
e
s
s
u
r
e
P
I
P
i
l
o
t

i
n
j
e
c
t
i
o
n
P
O
I
P
o
s
t

I
n
j
e
c
t
i
o
n
m
M
e
c
h
a
n
i
c
a
l
e
E
l
e
c
t
r
o
n
i
c
e
m
E
l
e
c
t
r
o
m
e
c
h
a
n
i
c
a
l
M
V
S
o
l
e
n
o
i
d

v
a
l
v
e
D
I
D
i
r
e
c
t

i
n
j
e
c
t
i
o
n
I
D
I
I
n
d
i
r
e
c
t

i
n
j
e
c
t
i
o
n
N
o
.

o
f

e
n
g
i
n
e

c
y
l
i
n
-
d
e
r
s
M
a
x
.

s
p
e
e
d
M
a
x
.

p
o
w
e
r

p
e
r

e
n
g
i
n
e

c
y
l
i
n
d
e
r
Axial-piston distributor pumps
VE F P 70 350 m IDI 3... 6 4800 25
VE F P 70 1205 m DI 4... 6 4400 25
VE F N, O 125 800 m DI 4, 6 3800 30
VP37 (VE-EDC) P 70 1250 em DI 3... 6 4400 25
VP37 (VE-EDC) O 125 800 em DI 4, 6 3800 30
VP30 (VE-M) P 70 1400 PI e, MV DI 4... 6 4500 25
VP30 (VE-M) O 125 800 PI e, MV DI 4, 6 2600 30
Radial-piston distributor pumps
VP44 (VR) P 85 1850 PI e, MV DI 4, 6 4500 25
VP44 (VR) N 175 1500 e, MV DI 4, 6 3300 45
Single-plunger injection pumps
PF(R) O 13... 450... m, em DI/IDI Arbitrary 4000 4...
120 1150 30
PF(R)Large diesel P, N, O, S 150... 800... m, em DI/IDI Arbitrary 300... 75...
engines 18000 1500 2000 1000
UIS P1 P 60 2050 PI e, MV DI 5
2, 2a
4800 25
UIS 30 N 160 1600 e, MV DI 8
2
4000 35
UIS 31 N 300 1600 e, MV DI 8
2
2400 75
UIS 32 N 400 1800 e, MV DI 8
2
2400 80
UPS 12 N 180 1600 e, MV DI 8
2
2400 35
UPS 20 N 250 1800 e, MV DI 8
2
3000 80
UPS (PF[R]) S 3000 1600 e, MV DI 6... 20 1500 500
Common Rail accumulator injection system
CR
3
P 100 1350 PI, POI
4
DI 3... 8 4800
5
30
CR
6
P 100 1600 PI, POI
7
DI 3... 8 5200 30
CR N, S 400 1400 PI, POI
8
DI 6... 16 2800 200
Robert Bosch GmbH
Injection-pump designs
The diesel engines injection system has the
task of injecting the diesel fuel into the en-
gines cylinders at very high pressure, in the
correct quantities, and at exactly the right
instant in time.
Depending upon the particular combustion
process, the nozzle extends into either the
main or the auxilary combustion chamber.
It opens at a fuel pressure which is specific
to the particular injection system, and closes
as soon as the pressure drops again. The ma-
jor difference between the various injection
systems is to be found in the high-pressure
generation process.
The very high injection pressures involved
necessitate the precision manufacture of all
the injection components from high-tensile
materials. All components must be exactly
matched to each other.
Electronic closed-loop control functions en-
able the inclusion of numerous auxiliary
functions (for instance, active surge damp-
ing, Cruise Control, and boost-pressure con-
trol).
PE standard in-line injection pumps
The standard PE in-line injection pumps
(Figure 1) have a plunger-and-barrel assem-
bly for each engine cylinder. As the name
implies, this comprises the pump barrel (1)
and the corresponding pump plunger (4).
The pump camshaft (7) is integrated in the
pump and driven by the engine, and forces
the pump plunger in the delivery direction
(in this case upwards). The plunger is re-
turned by its spring (5). The individual
plunger-and-barrel assemblies (also known
as pumping elements) are normally arranged
in-line, and plunger lift is invariable.
During the plungers upward travel, high-
pressure generation starts when the inlet
port (2) is closed by the plunger's top edge.
This instant in time is termed the start of
delivery. The plunger continues to move be-
yond this point and in doing so increases the
fuel pressure to such an extent that the noz-
zle opens and fuel is injected into the engine
cylinder.
A helix has been mechanically machined
into the plunger, and as soon as it opens the
inlet port the fuel pressure collapses, the
nozzle needle closes and injection stops.
6 Diesel fuel-injection systems: An overview Designs
Figure 1
a PE standard in-line
injection pump
b Control-sleeve in-
line injection pump
1 Pump barrel
2 Inlet port
3 Helix
4 Pump plunger
5 Plunger return
spring
6 Rotational travel due
to action of control
rack (injected fuel
quantity)
7 Camshaft
8 Control sleeve
9 Adjustment travel
due to actuating
shaft (start of fuel
delivery)
10 Flow of fuel to the
nozzle
X Effective stroke
a b
5
6
7
10
1
9
3
4
5
6
7
2
8
X
10
1
2
X
3
4
In-line fuel-injection pump: Principle of functioning 1
U
M
K
1
7
5
9
Y
Robert Bosch GmbH
The plunger travel between the closing and
opening of the inlet port is termed the effec-
tive stroke (X).
The pump is equipped with a control rack
(6) which rotates the plunger so that the po-
sition of the helix relative to the inlet port is
changed. This changes the plungers effective
stroke, and along with it the injected fuel
quantity. The control rack is controlled by
either a mechanical (flyweight) governor or
an electrical actuator mechanism.
Control-sleeve in-line injection pump
The control-sleeve in-line injection pump
differs from a conventional in-line injection
pump by having a control sleeve (Figure 1,
Pos. 8) which slides up and down the pump
plunger. By way of an actuator shaft (Figure
1, Pos. 9), this varies the plunger lift to (in-
let) port closing, and with it the start of in-
jection.
Since the start of injection can be varied in-
dependent of engine speed, the control-
sleeve version features an additional degree
of freedom compared to the standard PE in-
line injection pump.
Distributor injection pumps
The distributor pump has only one plunger-
and-barrel asembly for all the engines cylin-
ders (Figures 2 and 3). A vane-type supply
pump delivers fuel to the high-pressure
chamber (6). High-pressure generation is
the responsibility of either an axial piston
(Figure 2, Pos. 4) or several radial pistons
(Figure 3, Pos. 4). A rotating distributor
plunger opens and closes the metering slots
(8) and spill ports, and in the process dis-
tributes the fuel to the individual engine
cylinders via the injection nozzles (7). The
duration of injection (injection time) can be
varied using a control collar (Figure 2, Pos.
5) or a high-pressure solenoid valve (Figure
3, Pos. 5).
Axial-piston distributor pump
The drive for the cam plate (Figure 2, Pos. 3)
comes from the vehicles engine. The num-
ber of cams on the underside of the cam
plate corresponds to the number of engine
cylinders. These cams ride on the rollers (2)
of the roller ring with the result that a rotat-
ing-reciprocating movement is imparted to
the plunger. For one revolution of the drive-
shaft, the piston performs as many strokes as
there are engine cylinders.
Diesel fuel-injection systems: An overview Designs 7
Figure 2
1 Timing-device travel
on the roller ring
2 Roller
3 Cam plate
4 Axial piston
5 Control collar
6 High-pressure
chamber
7 Fuel outlet to the in-
jection nozzle
8 Metering slot
X Effective stroke
4 5
6
7
8 X 1
3 2
Port-and-helix-controlled axial-piston distributor pump: Principle of functioning 2
U
M
K
1
7
6
0
Y
Robert Bosch GmbH
On the port-and-helix-controlled VE axial-
piston distributor pump with mechanical
(flyweight) governor, or electronically con-
trolled actuator, the control collar (5) de-
fines the effective stroke and with it the in-
jected fuel quantity.
The timing device adjusts the pump's start
of delivery by rotating the roller ring (1).
Radial-piston distributor pumps
Here, instead of the cam plate as used on the
axial-piston distributor pump, a radial-pis-
ton pump with cam ring (Figure 3, Pos. 3)
and two to four radial pistons (4) is respon-
sible for high-pressure generation. Higher
pressures can be achieved with the radial-
piston pump than with the axial-piston ver-
sion, although this necessitates the pump
having to be much stronger mechanically.
The cam ring is rotated by the timing device
(1). On all radial-piston distributor pumps,
start of injection and duration of injection
(injection time) are solenoid-valve-con-
trolled.
Solenoid-valve-controlled distributor
pumps
On the solenoid-valve-controlled distributor
pump, an electronically controlled high-pres-
sure solenoid valve (5) is used to meter the in-
jected fuel quantity and to change the start-of-
injection point. With the solenoid valve
closed, pressure can build up in the high-pres-
sure chamber (6). Once the valve opens, fuel
escapes so that there is no fuel-pressure
buildup and no fuel is injected. The open and
closed-loop control signals are generated in
either one or two ECUs (pump ECU and en-
gine ECU, or only in the pump ECU).
Single-plunger injection pumps
PF single-plunger pumps
PF single-plunger pumps are used principally
for small engines, diesel locomotives, marine
engines, and construction machinery. Single-
plunger pumps are also suitable for operation
with viscous heavy oils.
Although these pumps have no camshaft of
their own (the F in their designation stands
for external drive) their basic operating con-
cept corresponds to that of the PE in-line
pumps. The cams for actuating the individual
PF single-plunger injection pumps are on the
engine camshaft. When used with large en-
gines, the mechanical-hydraulic governor, or
Figure 3
1 Timing device on
roller ring
2 Roller
3 Cam ring
4 Radial piston
5 High-pressure
solenoid valve
6 High-pressure
chamber
7 Fuel outlet to the
injection nozzle
8 Metering slot
8
7
5
3
1
4
2
6
Solenoid-valve-controlled radial-piston distributor pump: Principle of functioning 3
U
M
K
1
7
6
5
Y
Robert Bosch GmbH
the electronic controller, is attached directly to
the engine block. The fuel-quantity adjust-
ment as defined by the governor (or con-
troller) is transferred by a rack integrated in
the engine. The cams for actuating the indi-
vidual PF single-plunger pumps are on the
engine camshaft, and this means that injection
timing cannot be implemented by rotating the
camshaft. When used with large engines, the
mechanical-hydraulic governor, or the elec-
tronic controller, is attached directly to the en-
gine block. The fuel-quantity adjustment as
defined by the governor (or controller) is
transferred by a rack integrated in the engine.
Due to the direct connection to the engines
camshaft, this cannot be turned to implement
injection timing. Instead, injection timing
takes place by adjusting an intermediate ele-
ment, whereby an advance angle of several an-
gular degrees can be obtained. Adjustment is
also possible using solenoid valves.
Unit-Injector System (UIS)
In the Unit Injector System (UIS), injection
pump and injection nozzle form a single unit
(Fig. 4). One of these units is installed in the
engines cylinder head for each engine cylin-
der, and driven directly by tappet or indirectly
from the engine camshaft through a valve
lifter. Compared with the in-line and distribu-
tor injection pumps, considerably higher in-
jection pressures (up to 2050 bar) have be-
come possible due to the omission of high-
pressure lines. The fuel-injection parameters
are calculated by the ECU, and injection is
controlled by opening and closing the high-
pressure solenoid valve.
Unit-Pump System (UPS)
The modular Unit Pump System (UPS) uses
the same operating concept as the UIS. In
contrast to the UIS, pump and nozzle holder
(2) are joined by a short high-pressure deliv-
ery line (3) precisely matched to the respective
components. Separation of high-pressure-
generation stage and nozzle holder simplifies
installation at the engine. The UPS system fea-
tures an injection unit for each cylinder com-
prised of pump, delivery line, and nozzle
holder. The pump is driven from the engines
camshaft (6).
On the UPS too, injection duration and start
of injection are controlled electronically by a
high-speed high-pressure solenoid valve (4).
Diesel fuel-injection systems: An overview Designs 9
Figure 4
1 Actuating cam
2 Pump plunger
3 High-pressure
solenoid valve
4 Injection nozzle
Figure 5
1 Injection nozzle
2 Nozzle holder
3 High-pressure line
4 High-pressure
solenoid valve
5 Pump plunger
6 Actuating cam
2
1
3
4
High-pressure components of the Unit Injector
System (UIS): Principle of functioning
4
U
M
K
1
7
6
1
Y
4
3
1 5
2
6
High-pressure components of the Unit Pump
System (UPS): Principle of functioning
5
U
M
K
1
7
6
6
Y
Robert Bosch GmbH
Accumulator injection system
Common-Rail System CRS
In this system the processes of pressure gen-
eration and fuel injection are decoupled
from each other (Figure 6). Injection pres-
sure is generated and controlled by a high-
pressure pump (1), and is for the most part
independent of engine speed and injected
fuel quantity. It is permanently available in
the rail (fuel accumulator, 2) for injection.
The CRS thus provides maximum flexibil-
ity in the injection-process design.
Each engine cylinder is provided with an in-
jector (4) which forms the injection unit.
Opening and closing the high-pressure sol-
enoid valve (3) controls the injection
process. The instant of injection and the in-
jected fuel quantity are calculated in the
ECU.
Figure 7
1 P1 Unit Injector
(passenger cars)
2 CP2 Common Rail
high-pressure pump
(commercial vehi-
cles)
3 Rail with injectors
(commercial-vehicle
CRS)
4 VP30 distributor
pump (passenger
cars)
5 RP39 control-sleeve
in-line pump (com-
mercial vehicles)
Figure 6
1 High-pressure pump
2 Rail (high-pressure
fuel accumulator)
3 High-pressure sole-
noid valve
4 Injector
5 Injection nozzle
1
2
3
4
5
High-pressure components of the Common Rail
System (CRS): Principle of functioning
6
U
M
K
1
7
6
2
Y
1
2 3
4
5
10 cm
Examples of the high-pressure components as used in Bosch diesel injection systems 7
U
M
K
1
7
6
7
Y
Robert Bosch GmbH
Diesel fuel-injection systems: An overview A brief history of diesel injection 11
A brief history of diesel injection
Bosch started at the end of 1922 with the
development of a fuel-injection system for
diesel engines. All technical factors were
favorable: Bosch had experience with internal-
combustion engines, production engineering
was highly developed, and above all it was
possible to apply the know-how that Bosch
had accumulated in the manufacture of lubri-
cation pumps. Notwithstanding these facts, for
Bosch there was considerable risk involved in
this development work, and numerous chal-
lenges had to be surmounted.
The first injection pumps went into series
production in 1927. At that time, the precision
achieved in their manufacture was absolutely
unique. They were small and of lightweight
design, and were behind the diesel engine
now being able to run at high speeds. These
in-line pumps were installed as from 1932 in
commercial vehicles, and as from 1936 in pas-
senger cars. From this point onwards, there
was not letup in the development of the diesel-
engine and its injection equipment.
In 1976, the diesel engine was given a new
lease of life when Bosch introduced the distribu-
tor injection pump with automatic timing device.
And a decade later, after years of intensive
development work to bring it to the volume-pro-
duction stage, Bosch brought the Electronic
Diesel Control (EDC) onto the market.
Development engineers are constantly
faced with the need for the even more precise
injection of minute quantities of diesel fuel, at
exactly the right instant in time, and under
higher and higher injection pressures. This has
led to a number of innovative injection-system
developments (see adjacent Figure).
The diesel engine is still at the forefront
regarding fuel economy and efficient utilization
of fuel.
New injection systems make even better
use of this potential. In addition, the internal-
combustion engines power output is continu-
ously increasing, while its noise and emissions
figures have continued to drop.
Milestones in
diesel injection technology
1927
First series-
production in-line pump
1962
First axial-
piston distributor
pump,
the EP-VM
1986
The first electronically
controlled axial-piston
distributor pump
1994
First Unit Injector
System (UIS) for
commercial vehicles
1995
First Unit Pump
System (UPS)
1997
First Common
Rail accumulator
injection system
(CRS)
1998
First Unit Injector
System (UIS) for
passenger cars
1996
First radial-
piston distributor
pump
U
M
K
1
7
5
3
E
Robert Bosch GmbH
Modern electronic diesel-engine control
permits the precise and highly flexible defi-
nition of the fuel-injection parameters. This
is the only way to comply with the wide
range of technical demands made on a
modern diesel engine. The Electronic Diesel
Control (EDC) is subdivided into the three
system blocks Sensors and desired-value
generators, ECU, and Actuators.
Technical requirements
The calls for reduced fuel consumption and
emissions, together with increased power
output and torque, are the decisive factors
behind present-day developments in the
diesel fuel-injection field.
In the past years this has led to an increase
in the use of direct-injection (DI) diesel en-
gines. Compared to prechamber or whirl-
chamber engines, the so-called indirect-in-
jection (IDI) engines, the DI engine operates
with far higher injection pressures. This
leads to improved A/F mixture formation,
combustion of the more finely atomized fuel
droplets is more complete, and there are less
unburnt hydrocarbons (HC) in the exhaust
gas. In the DI engine, the improved mixture
formation and the fact that there are no
overflow losses between pre-chamber/whirl
chamber and the main combustion chamber
results in fuel-consumption savings of be-
tween 10...15% compared to the IDI engine.
In addition, the increasing requirements re-
garding vehicle driveability have a marked
effect on the demands made on modern en-
gines, and these are subject to increasingly
more severe requirements with regard to ex-
haust-gas and noise emissions (NO
X
, CO,
HC, particulates).
This has led to higher demands being
made on the injection system and its control
with respect to:
High injection pressures,
Structured rate-of-discharge curve,
Pilot injection and possibly post injection,
Adaptation of injected fuel quantity, boost
pressure, and injected fuel quantity to the
given operating state,
Temperature-dependent start quantity,
Load-independent idle-speed control,
Cruise Control,
Closed-loop-controlled exhaust-gas recir-
culation (EGR), and
Tighter tolerances for injected fuel quan-
tity and injection point, together with
high accuracy to be maintained through-
out the vehicles useful life.
Conventional mechanical (flyweight) gover-
nors use a number of add-on devices to reg-
ister the various operating conditions, and
ensure that mixture formation is of high
standard. Such governors, though, are re-
stricted to simple open-loop control opera-
tions at the engine, and there are many im-
portant actuating variables which they can-
not register at all or not quickly enough.
The increasingly severe demands it was sub-
jected to, meant that the EDC developed from
a simple system with electrically triggered ac-
tuator shaft to become a complex engine-
management unit capable of carrying out
real-time processing of a wide variety of data.
System overview
In the past years, the marked increase in the
computing power of the microcontrollers
available on the market has made it possible
for the EDC (Electronic Diesel Control) to
comply with the above-named stipulations.
In contrast to diesel-engine vehicles with
conventional in-line or distributor injection
pumps, the driver of an EDC-controlled ve-
hicle has no direct influence, for instance
through the accelerator pedal and Bowden
cable, upon the injected fuel quantity.
12 Electronic Diesel Control (EDC) Technical requirements
Electronic diesel control EDC
Robert Bosch GmbH
On the contrary, the injected fuel quantity is
defined by a variety of actuating variables,
for instance:
Driver input (accelerator-pedal setting),
Operating state,
Engine temperature,
Intervention from other systems
(e.g. TCS),
Effects on toxic emissions etc.
Using these influencing variables, the ECU
not only calculates the injected fuel quantity,
but can also vary the instant of injection.
This of course means that an extensive safety
concept must be implemented that detects
deviations and, depending upon their sever-
ity, initiates appropriate countermeasures
(e.g. limitation of torque, or emergency
(limp-home) running in the idle-speed
range). EDC therefore incorporates a num-
ber of closed control loops.
EDC also permits the exchange of data with
other electronic systems in the vehicle (e.g.
with the traction control system (TCS), the
electronic transmission-shift control, or
with the electronic stability program (ESP).
This means that engine management can be
integrated in the overall vehicle system (e.g.
for engine-torque reduction when shifting
gear with an automatic gearbox, adaptation
of engine torque to wheel slip, release signal
for fuel injection from the vehicle immobi-
lizer, etc.).
The EDC system is fully integrated in the
vehicles diagnostics system. It complies with
all OBD (On-Board-Diagnosis) and EOBD
(European On-Board Diagnosis) stipula-
tions.
System blocks
The EDC system comprises three system
blocks: (Fig. 1):
1. Sensors and desired-value generators (1)
for the detection of operating conditions
(e.g. engine rpm) and of desired values (e.g.
switch position). These convert the various
physical quantities into electrical signals
2. Electronic control unit (ECU) (2) processes
the information from the sensors and the
desired-value generators in accordance with
given computational processes (control al-
gorithms). The ECU triggers the actuators
with its electrical output signals and also sets
up the interfaces to other systems in the ve-
hicle (4) and to the vehicle diagnosis facility
(5).
3. Solenoid actuators (3) convert the ECUs
electrical output signals into mechanical
quantities (e.g. for the solenoid valve which
controls the injection, or for the solenoid of
the actuator mechanism).
Electronic Diesel Control (EDC) System blocks 13
Figure 1
1 Sensors and de-
sired-value genera-
tors (input signals)
2 ECU
3 Actuators
4 Interface to other
systems
5 Diagnosis interface
4 2
1
3
5
Major EDC components 1
U
A
E
0
7
3
4
Y
Robert Bosch GmbH
14 Electronic Diesel Control (EDC) In-line injection pumps
Engine rpm
(crankshaft)
Fuel temperature, control-rack travel
Accelerator-pedal sen-
sor with low-idle switch
Boost pressure
Start of injection**
(needle-motion
sensor)
Vehicle speed
Engine rpm and
cylinder identification
(camshaft)
ECU MS 5/6.1
Signal inputs
Sensor evaluation
Ambient-pressure sensor
Signal processing
- Idle-speed control
- Intermediate-speed
control
- External intervention in
injected fuel quantity
- Injected fuel-quantity
control and limitation
- Cruise Control
- Vehicle-speed limitation
- Calculation of start-of-
delivery and delivery
period
- Supplementary special
adaptations*
System diagnosis
Substitute functions
Engine diagnosis
Power stages
Signal outputs
CAN communication
Diagnosis
communication
EoL programming
Power supply
Redundant fuel shutoff
(ELAB)
***
Injected-fuel-quantity actuator
Start-of-delivery actuator*
Supplementary
driver stages*
ISO interface
(e.g. OBD)
CAN interface*
In-line
injection pump
Switch for
intermediate-
speed control
Clutch switch
Door contact
Vehicle-speed-
limitation lamp
+
Diagnosis lamp
+
* Optional
** On control-sleeve in-line injection pumps,
*** Start-of-delivery actuator on control- sleeve in-line injection pumps.
Engine temperature
(coolant)
Brake switch
Changeover switch for
Cruise Control and
vehicle-speed limitation
Communication
Actuators
Input signals
Glow-plug and
starter switch
Exhaust-brake
switch
Cruise Control
operator unit
Multi-stage switch
for maximum-speed
limiter
Multi-stage switch for
injected-fuel-quantity
limitation, and max.
rpm control
Boost-pressure actuator
Exhaust-brake triggering
Intercooler-bypass
triggering
L
Input pwm signals
K
CAN
+
24V (12V*)
Kl. 15
Overview of the EDC components for in-line injection pumps 1
N
A
E
0
7
4
7
E
Robert Bosch GmbH
Port-and-helix-controlled axial-piston distributor pumps
Electronic Diesel Control (EDC) Axial-piston distributor pumps 15
Engine rpm
(crankshaft)
Actuator position
Timing-device
solenoid valve
ELAB
Actuator
Boost pressure
Intake-air temperature
Engine temperature
(coolant)
Fuel temperature
Air mass
Vehicle speed
(also possible via CAN) Km/ h
ECU EDC 15V
Signal inputs
Sensor evaluation
Signal processing:
- Cylinder-balance
control
- Active surge damper
- External
torque intervention
- Immobilizer
- Injected-fuel-quantity
- Cruise Control
- Calculation of start of
period
- Supplementary
adaptations*
System diagnosis
Engine diagnosis
Power stages
Signal outputs
CAN communication
OBD communication
EoL programming
Power supply
EGR positioner
Supplementary driver
stages*
A/C compressor
Glow control unit
ISO interface
(e.g. OBD)
Fuel-consumption
signal (TQ signal)
CAN interface*
Brake switch
Main A/C switch
Start of injection*
(needle-motion
sensor)
+
+
Warning lamp
+
+
OBD lamp
+
*Optional
Engine-oil temperature
Clutch switch
Glow-plug and
starter switch
Communication
Actuators
Input signals
+
+
+
Multi-stage Cruise
Control switch
L
Engine-speed signal
(TD signal)
Input for pwm
signals*
K
CAN
12V
+
Kl. 15
Distributor pump
Overview of the EDC components for VE-EDC port-and-helix-controlled distributor pumps 2
N
A
E
0
7
4
8
E
Robert Bosch GmbH
Solenoid-valve-controlled axial-piston
and radial-piston distributor pumps
16 Electronic Diesel Control (EDC) Axial-piston and radial-piston distributor pumps
Engine rpm
(crankshaft)
Angle of rotation of the trigger wheel, timing-device setting (IWZ signal)
and kick-down switch
Boost pressure
Air temperature
Engine temperature
(coolant)
Fuel temperature
Air mass
Vehicle speed
ECU EDC15 M
Signal inputs
Sensor evaluation
Signal processing
- Cylinder-balance
control
- External
torque intervention
- Immobilizer
- Cruise Control
- Cylinder shutoff (only
for commercial vehs.)
delivery, and of delivery
period
- Pilot-injection control*
- Supplementary
special adaptations*
System diagnosis
Engine diagnosis
Solenoid-valve driver
stages
Power stages
Signal outputs
CAN communication
Diagnosis
communication
EoL programming
Power supply +12V
CAN-Bus
DZG
MAB
EGR positioner
Supplementary driver
stages*
A/C compressor
ISO interface
(e.g. diagnostics)
Fuel-consumption
signal (TQ signal)
CAN interface*
Distributor pump
VP 30
VP 44
Main
relay
Brake switch
Main A/C switch
Start of injection*
(needle-motion
sensor)
+
+
+
12V
(24V*)
Warning lamp
+
+
Diagnosis lamp
+
*Optional
On distributor pumps with pump ECU PSG16, the engine ECU is integrated in the pump ECU
Engine-oil temperature
Clutch switch
Glow-plug and
starter switch
Communication
Actuators
Input signals
+
+
+
Multi-stage Cruise
Control switch
L
Engine rpm signal
(TD signal)
Input for pwm signals*
K
CAN
Glow control unit
Overview of the EDC components for solenoid-valve-controlled distributor pumps VE-MV, VR 1
N
A
E
0
7
4
9
E
Robert Bosch GmbH
Common Rail System (CRS)
Electronic Diesel Control (EDC) Common Rail System (CRS) 17
Engine rpm
(crankshaft)
Engine rpm
and cylinder
identification (camshaft)
Rail pressure
sor, with low-idle switch
and kick-down switch
Boost pressure
Charge-air pressure
Engine temperature
(coolant)
Rail-pressure control valve
of the high-pressure pump
Element shutoff*
Electronic shutoff
or electric fuel pump
EGR positioner
Boost-pressure actuator*
Throttle-valve actuator
Auxiliary heater*
ISO interface
(e.g. diagnosis)
Glow control unit (GZS)
Engine rpm signal
(TD signal)
Diagnosis lamp
CAN interface CAN
Clutch switch (or P/N
contact for automatic
transmissions)
Terminal 15
Multi-stage switch for
maximum-speed limiter
and for Cruise Control
Air mass or exhaust-
gas-signal check-back
Terminal 50*
+
Communication
Actuators
Input signals
12V
ECU
EDC 15 C / MS 6.3
Signal processing:
control
- Smooth-running
control (SRC)
- External
torque intervention
- Immobilizer
- Cruise Control*
- Vehicle-speed
limitation*
- Cylinder shutoff
- Fuel-quantity control
- Fuel-pressure control
- Start-of-injection control
- Pilot-injection control
- Post-injection control*
adaptations*
Signal inputs
Sensor evaluation
System diagnosis
Engine diagnosis
stages
Power stages
Signal outputs
CAN communication
Diagnosis communication
EoL programming
Power supply
Main
relay
*Optional
Injectors
(max. 6 per ECU)
* *
Exhaust-gas
temperature*
Fan control*
Starter*
Additional driver stages*
Intake-tract switch-over*
L
K
Overview of the EDC components for the Common Rail System (CRS) 2
N
A
E
0
7
5
0
E
Robert Bosch GmbH
Unit Injector System (UIS) for passenger cars
18 Electronic Diesel Control (EDC) Unit Injector System (UIS) for passenger cars
Engine rpm
(crankshaft)
Engine rpm and
cylinder recognition
(camshaft)
Accelerator-pedal
sensor with low-idle
switch and kick-down
switch (2nd sensor*)
Boost pressure
Intake-air temperature
Engine temperature
(coolant)
Fuel temperature
Air mass
Vehicle speed
ECU EDC15P
Signal inputs
Sensor evaluation
Signal processing
- Cylinder-balance control
- External
torque intervention
- Immobilizer
- Cruise Control
period
- Start-of-delivery (BIP)
correction
adaptations*
System diagnosis
Engine diagnosis
stages
Power stages
Signal outputs
CAN communication
Diagnosis
communication
EoL programming
Power supply
Start of delivery, delivery period
Glow-relay control
A/C switch-off
EGR actuator
Supplementary
low-power driver stages
(e.g. A/C switch-off, fan,
auxiliary heater)
*
ISO interface
(e.g. diagnosis)
System lamp
MIL lamp
(for diagnosis)
CAN interface
Engine rpm signal
(TD signal)
Fuel-consumption
signal (TQ signal)
Unit Injector (max. 5 per ECU)
Main
relay
MIL request
(request for
MIL lamp)
Brake switch
Terminal 15
Glow-relay status
Gearbox input
Air-conditioner input
+
+
12 V
+
+
*Optional
Clutch switch
Communication
Actuators
Input signals
+
Multi-stage Cruise
Control switch
L
K
CAN
Overview of the EDC components for a passenger-car unit injector system (UIS) 1
N
A
E
0
7
3
6
E
Robert Bosch GmbH
Unit Injector System (UIS)
and Unit Pump System (UPS) for commercial vehicles
Electronic Diesel Control (EDC) UIS and UPS for commercial vehicles 19
+
Engine rpm
(crankshaft)
Engine rpm and
cylinder identification
(camshaft)
Exhaust-gas
turbocharger,
rpm signal
Accelerator-pedal
sensor with low-idle
switch and kick-down
switch*
Boost pressure
Charge-air temperature
Engine temperature
(coolant)
Fuel temperature
Vehicle speed
(also possible
via CAN)
Km/ h
Start-of-delivery, delivery period
Exhaust brake
Additional driver stages
(e.g. fan control)
Diagnosis lamp
Input for
pwm signals
Engine rpm signal
(TD signal)
Multi-stage
Cruise Control
switch
Brake contact
Clutch contact
Exhaust-brake
contact
Parking-brake
contact
Terminal 15
Communication
Actuators
Input signals
24V (12V*)
ECU MS 6.2
Signal inputs
Sensor evaluation
Signal processing:
control
- External
torque intervention
- Immobilizer
- Cruise Control
- Vehicle-speed
limitation
- Cylinder shutoff
delivery and
delivery period
- Start-of-delivery (BIP)
correction
- Supplementary
special adaptations*
System diagnosis
Calibration
Engine diagnosis
stages
Driver stages
Signal outputs
CAN communication
Diagnosis communic.
EoL programming
Power supply
*Optional
UP* (max. 8 per ECU)
UI* (max. 8 per ECU)
or
Multi-function switch
ISO interface
(e.g. diagnosis)
CAN interface
Main
relay
CAN
L
K
+
*
*
Overview of the EDC components for Unit Injector System (UIS) and Unit Pump Systems (UPS) for commercial vehicles 2
N
A
E
0
7
3
5
E
Robert Bosch GmbH
Sensors register operating states (e.g. engine
speed) and setpoint/desired values (e.g. ac-
celerator-pedal position). They convert
physical quantities (e.g. pressure) or chemi-
cal quantities (e.g. exhaust-gas concentra-
tion) into electric signals.
Automotive applications
Sensors and actuators represent the inter-
faces between the ECUs, as the processing
units, and the vehicle with its complex drive,
braking, chassis, and bodywork functions
(for instance, the Engine Management, the
Electronic Stability Program ESP, and the air
conditioner). As a rule, a matching circuit in
the sensor converts the signals so that they
can be processed by the ECU.
The field of mechatronics, in which me-
chanical, electronic, and data-processing
components are interlinked and cooperate
closely with each other, is rapidly gaining in
importance. They are integrated in modules
(e.g. in the crankshaft CSWS (Composite
Seal with Sensor) module complete with
rpm sensor).
Since their output signals directly affect not
only the engines power output, torque, and
emissions, but also vehicle handling and
safety, sensors, although they are becoming
smaller and smaller, must also fulfill de-
mands that they be faster and more precise.
These stipulations can be complied with
thanks to mechatronics.
Depending upon the level of integration,
signal conditioning, analog/digital conver-
sion, and self-calibration functions can all
be integrated in the sensor (Fig. 1), and in
future a small microcomputer for further
signal processing will be added. The advan-
tages are as follows:
Lower levels of computing power are
needed in the ECU,
A uniform, flexible, and bus-compatible
interface becomes possible for all sensors,
Direct multiple use of a given sensor
through the data bus,
Registration of even smaller measured
quantities,
Simple sensor calibration.
20 Sensors Automotive applications
Sensors
Figure 1
SE Sensor(s)
SA Analog signal con-
ditioning
A/D Analog-digital con-
verter
SG Digital ECU
MC Microcomputer
(evaluation electron-
ics)
SE SA
A

D
SE SA
A

D
SE SA
SE Conventional
1
st
Integration level
2
nd
integration level
3
rd
integration level MC SG
SG
SG
SG SA
A

D
A

D
Sensors Transmission path ECU
Susceptible to
interference
(analog)
Resistant to
interference
(analog)
Immune to
interference
(digital)
Immune to
interference
(digital)
Multiple
tap-off
Bus-
compatible
Bus-
compatible
Sensor integration levels 1
U
A
E
0
0
3
7
-
1
E
Robert Bosch GmbH
Temperature sensors
Applications
Engine-temperature sensor
This is incorporated in the coolant circuit
and measures the coolant temperature as an
indication of engine temperature (Fig. 1).
This information is needed for the engine-
management system. The measurable tem-
perature range is between 40 and +130 C.
Air-temperature sensor
This is installed in the engine's intake tract
and measures the temperature of the intake
air. In coordination with a boost-pressure
sensor, this intake-air temperature can be
used to precisely measure the mass of the air
drawn into the engine. Apart from this, the
setpoint values for closed control loops (e.g.
EGR, boost-pressure control) can be
adapted as a function of the air temperature.
The measurable temperature range is be-
tween 40 and +120C.
Engine-oil temperature sensor
The signal from the engine-oil temperature
sensor is used when determining the service
interval. The measurable temperature range
is between 40 and+170 C.
Fuel-temperature sensor
This sensor is installed in the low-pressure
stage of the fuel system. The fuel tempera-
ture is an important factor in precisely
defining the correct injected fuel quantity.
The measurable temperature range is be-
tween 40 and+120C.
Exhaust-gas temperature sensor
This sensor is installed at a point in the ex-
haust system which is critical with regard to
temperature. It is used in the control of the
exhaust-gas treatment system. Platinum is
usually used for the measuring resistor. The
measurable temperature range is between
40 and +1000C.
Design and operating concept
Depending upon the particular application,
these temperature sensors are available in a
variety of different shapes and versions. A
temperature-dependent semiconductor
measuring resistor is mounted inside the
sensor housing. This resistor is usually of the
NTC (Negative Temperature Coefficient)
type, or less commonly of the PTC (Positive
Temperature Coefficient) type. In other
words, when subjected to increasing temper-
ature, its electrical resistance decreases
(NTC) or increases (PTC) dramatically.
The measuring resistor is part of a voltage-
distributor circuit to which 5 V is applied,
and the voltage measured across it is there-
Sensors Temperature sensors 21
Figure 1
1 Electrical
connections
2 Housing
3 Seal ring
4 Sensor thread
5 Measuring resistor
6 Coolant
1
1 cm
2 3 6 5 4
Coolant-temperature sensor 1
U
M
K
0
1
2
4
-
7
Y
Characteristic curve of an NTC resistor 2
-40 0 40 80 120C
10
2
10
3
10
4
R
e
s
i
s
t
a
n
c
e
Temperature
U
M
K
1
9
9
8
E
Robert Bosch GmbH
fore temperature-dependent. This is in-
putted to the ECU through an A/D con-
verter and is a measure for the temperature
at the sensor. The engine ECU incorporates
a characteristic curve which allocates a spe-
cific temperature to each output-voltage
value or resistance (Fig. 2, Page 21).
Micromechanical pressure
sensors
Applications
Intake-manifold sensor or boost-pressure
sensor
This sensor measures the absolute pressure
in the intake manifold (typically 250 kPa or
2.5 bar) between the supercharger and the
engine. The actual measurement is referred
to a reference vacuum and not to the sur-
rounding pressure. This permits precise
measurement of the air mass so that the su-
percharger can be controlled in accordance
with engine requirements.
Atmospheric-pressure sensor
The atmospheric-pressure sensor can be in-
stalled in the ECU or at another location in
the engine compartment. Its signal is used
for altitude-dependent correction of the set-
point values for the closed control loops (for
instance for the EGR and the boost-pressure
control). This permits the differences in at-
mospheric pressure encountered at different
altitudes to be taken into account. The at-
mospheric-pressure sensor measures ab-
solute pressure (60...115 kPa, 0.6...1.15 bar).
Oil-pressure and fuel-pressure sensors
Oil-pressure sensors are installed in the oil
filter for measuring the absolute oil pressure.
This information is applied for determining
engine loading as required for the Service
Display. The sensors pressure range is
50...1000 kPa (0.5...10.0 bar). The sensor el-
ements high resistance to the measured
medium means that it can also be used for
the fuel-pressure measurement in the fuel-
system low-pressure stage. The sensor is fit-
22 Sensors Micromechanical pressure sensors
p
1 3
2
5
R
1
R
1
R
2
4
U
M U
0
R
1
R
2
R
2
R
1
Sensor element of a pressure sensor with reference
vacuum on the component-buildup side (schematic)
1
U
A
E
0
0
1
7
-
1
Y
Sensor element of the pressure sensor with cap and
reference vacuum on the component side
3
U
A
E
0
7
2
1
Y
p
7
6
5
4 1
2
3
Sensor element of the pressure sensor with cap and
reference vacuum on the component side (design)
2
U
A
E
0
6
4
8
-
2
Y
Figure 1
1 Diaphragm
2 Silicon chip
3 Reference vacuum
4 Glass (Pyrex)
5 Wheatstone bridge
p Measured pressure
U
0
Supply voltage
U
M
Measurement
voltage
R
1
Measuring resistors
(compressed) and
R
2
Measuring resistors
(stretched)
Figure 2
1, 3 Electrical connec-
tions with glass-en-
closed lead-in
2 Reference vacuum
4 Sensor element
(chip) with evalua-
tion electronics
5 Glass base
6 Cap
7 Pressure connection
for measured pres-
sure p
Robert Bosch GmbH
ted either in the fuel filter or on it, and its
signal is used to monitor the degree of fuel
contamination (measuring range 20...400
kPa or 0.2...4 bar).
Design with the reference vacuum on
the component side
Design
The measuring element is the heart of the
micromechanical pressure sensor, and is
comprised of a silicon chip (Fig. 1, Pos. 2)
into which a thin diaphragm (1) has been
etched micromechanically. Four measuring
resistors (R
1
, R
2
), whose electrical resistances
change when mechanical pressure is applied,
are arranged on the diaphragm. On its
structure side, the sensor element is sur-
rounded and sealed off by a cap which en-
closes the reference vacuum (Figs. 2 and 3).
A temperature sensor can also be integrated
in the pressure sensor (Fig. 4, Pos. 1), whose
signals can be evaluated separately. This has
the advantage that only a single sensor hous-
ing is needed when both temperature and
pressure are to be measured.
Operating concept
The sensor-element diaphragm bends by
several m (10...1000 m) as a function of
the applied pressure. The resulting mechani-
cal tension causes the four measuring resis-
tors on the diaphragm to change their resis-
tance (piezoresistive effect).
These measuring resistors are arranged on
the silicon chip so that when the diaphragm
deforms (due to pressure application), the
electrical resistance of two of the resistors
increases, and that of the other two de-
creases. Since the resistors are part of a
Wheatstone bridge (Fig. 1, Pos. 5), when the
resistance values change so does the voltage
ratio across the measuring resistors, and
with it the measurement voltage U
M
which
thus becomes a measure of the pressure ap-
plied to the diaphragm.
Using a bridge circuit enables a higher
measurement voltage to be generated than
would be possible with a single resistor. The
Wheatstone bridge, therefore, permits a
higher level of sensor sensitivity.
The component side of the diaphragm to
which no pressure is applied is subjected to a
reference vacuum (Fig. 2, Pos. 2) so that the
sensor measures absolute pressure.
The signal-conditioning electronics are in-
tegrated on the chip and have the job of am-
plifying the bridge voltage, compensating for
temperature fluctuations, and linearizing the
pressure curve. Output voltage is 0...5 V and
via the sensors electrical plug-in connection
(Fig. 4, Pos. 5) it is inputted to the ECU which
uses it to calculate the pressure curve (Fig. 5).
Sensors Micromechanical pressure sensors 23
Figure 4
1 Temperature sensor
(NTC),
2 Housing base
3 Intake-manifold wall
4 O-rings
5 Electrical plug-in
connection
6 Housing cover
7 Sensor element
1 2 3 4 5
6
7
1 cm
Micromechanical pressure sensor with
reference vacuum on the component side
4
U
A
E
0
7
2
2
Y
Pressure
kPa 250 100
O
u
t
p
u
t

v
o
l
t
a
g
e
V
4.65
1.87
Characteristic curve of a micromechanical boost-
pressure sensor (example)
5
U
A
E
0
7
1
9
-
1
E
Robert Bosch GmbH
Version with the reference vacuum in a
cavity
Design
The pressure sensor with reference vacuum
inside a cavity (Figs. 6 and 8) is used as an
intake-manifold or boost-pressure sensor. It
is simpler in design than the version with
the reference vacuum on the component
side. A silicon chip with etched diaphragm
and four measuring resistors in a bridge cir-
cuit is mounted as the sensor element on a
glass base similar to the sensor version with
cap and reference vacuum on the compo-
nent side. In contrast to the latter version
though, there is no hole in the cavity-type
sensors glass base for transmitting the mea-
sured pressure from the sensors rear side to
the sensor element. Instead, pressure is ap-
plied to the silicon chip at the side contain-
ing the evaluation electronics. This side
must therefore be sealed off with a special
gel to protect it against environmental ef-
fects (Fig. 7, Pos. 1). The reference vacuum is
located in the hollow space (cavity) between
the silicon chip (6) and the glass base (3).
The complete measuring element is
mounted on the ceramic hybrid (4) which is
provided with solder surfaces for connec-
tions within the sensor.
It is also possible to integrate a temperature
sensor inside the pressure sensors housing.
This extends into the air stream and is thus
able to react extremely quickly to tempera-
ture changes.
Operating concept
Operating concept, signal conditioning and
amplification, as well as the characteristic
curve, are all identical to those of the sensor
with cap and reference vacuum on the com-
ponent side. The sole difference is that the
sensor-elements diaphragm, and with it the
measuring resistors, is deformed in the op-
posite direction.
24 Sensors Micromechanical pressure sensors
Figure 6
1 Intake-manifold wall
2 Housing
3 Seal ring
4 Temperature sensor
(NTC)
connection
6 Housing cover
7 Sensor element
Figure 7
1 Protective gel
2 Gel frame
3 Gass base
4 Ceramic hybrid
5 Cavity with refer-
ence vacuum
6 Sensor element
(chip) with evalua-
tion electronics
7 Bonded connection
p Measured pressure
5 1
4
3
2
6
7
1 cm
Micromechanical pressure sensor with reference
vacuum in a cavity
6
U
M
K
1
6
4
5
-
1
Y
Micromechanical pressure sensor with
reference vacuum in a cavity and
integrated temperature sensor
8
U
M
K
1
9
9
7
Y
1
2
3
4
p
6
5
7
U
M
K
1
6
4
4
-
1
Y
Sensor element with reference
vacuum in a cavity
7
Robert Bosch GmbH
Rail-pressure sensors
Application
In the Common-Rail injection system and
the gasoline direct-injection system MED-
Motronic, these sensors are used to measure
the fuel pressure in the high-pressure fuel
accumulator (or rail, from which the system
took its name). Strict compliance with the
stipulated fuel pressure is of extreme impor-
tance with regard to emissions, noise, and
engine power. The fuel pressure is regulated
in a control loop, and deviations from the
desired pressure level are compensated for
by a pressure-control valve.
The rail-pressure sensors feature very tight
tolerances, and in the main measuring range
the measuring accuracy is better than 2% of
the measuring range.
These rail-pressure sensors are used in the
following engine systems:
Common-Rail diesel injection system
(CRS)
Maximum operating pressure p
max
(rated pressure) is 160 MPa (1600 bar).
Gasoline direct injection MED-Motronic
For this gasoline direct-injection system,
operating pressure is a function of load
and rotational speed, and is 5...12 MPa
(50...120 bar).
The heart of this sensor is a steel diaphragm
on which measuring resistors in the form of
a bridge circuit have been vapor-deposited
(Fig. 1, Pos. 3). The sensors measuring
range is a function of diaphragm thickness
(thicker diaphragms for higher pressures,
thinner diaphragms for lower pressures). As
soon as the pressure to be measured is ap-
plied to the diaphragm through the pressure
connection (Fig. 1, Pos. 4), this bends and
causes a change in the resistance of the mea-
suring resistors (approx. 20 m at 1500 bar).
The output voltage generated by the bridge
is in the range 0...80 mV and is inputted to
the evaluation circuit (2) in the sensor. This
amplifies the bridge signal to 0...5 V and
transmits it to the ECU which uses it to-
gether with a stored characteristic curve to
calculate the pressure (Fig. 2).
Sensors Rail-pressure sensors 25
Figure 1
connection
2 Evaluation circuit
3 Steel diaphragm
with measuring re-
sistors
4 Pressure connection
5 Mounting thread
2
3
4
5
p
1
2 cm
Rail-pressure sensor 1
U
M
K
1
5
7
6
-
1
Y
p
max
0
4.5
0.5
Pressure
O
u
t
p
u
t

v
o
l
t
a
g
e
V
Rail-pressure sensor: Characteristic curve 2
U
A
E
0
7
1
9
-
2
E
Robert Bosch GmbH
Inductive engine-speed
(rpm) sensors
Applications
Such engine-speed sensors are used for mea-
suring:
Engine rpm,
Crankshaft position
(for information on the position of the
engine pistons).
The rotational speed is calculated from the
intervals between the signals from the rpm
sensor. The output signal from the rpm sen-
sor is one of the most important quantities
in electronic engine management.
The sensor is mounted directly opposite a
ferromagnetic trigger wheel (Fig. 1, Pos. 7)
from which it is separated by a narrow air
gap. It has a soft-iron core (pole pin) (4),
which is enclosed by the solenoid winding
(5). The pole pin is also connected to a per-
manent magnet (1), and a magnetic field ex-
tends through the pole pin and into the trig-
ger wheel. The level of the magnetic flux
through the winding depends upon whether
the sensor is opposite a trigger-wheel tooth
or gap. Whereas the magnets stray flux is
concentrated by a tooth and leads to an in-
crease in the working flux through the wind-
ing, it is weakened by a gap. When the trig-
ger wheel rotates therefore, this causes a
fluctuation of the flux which in turn gener-
ates a sinusoidal voltage in the solenoid
winding which is proportional to the rate of
change of the flux (Fig. 2). The amplitude of
the AC voltage increases strongly along with
increasing trigger-wheel speed (several
mV...>100 V). At least about 30 rpm are
needed to generate an adequate signal level.
The number of teeth on the trigger wheel
depends upon the particular application. On
solenoid-valve-controlled engine-manage-
ment systems for instance, a 60-pitch trigger
wheel is normally used, although 2 teeth are
omitted (Fig. 1, Pos. 7) so that the trigger
wheel has 60 2 = 58 teeth. The very large
tooth gap (7) is allocated to a defined crank-
shaft position and serves as a reference mark
for synchronizing the ECU.
There is another version of the trigger
wheel which has one tooth per engine cylin-
der. In the case of a 4-cylinder engine, there-
fore, the trigger wheel has 4 teeth, and 4
pulses are generated per revolution.
The geometries of the trigger-wheel teeth
and the pole pin must be matched to each
other. The evaluation-electronics circuitry in
the ECU converts the sinusoidal voltage,
which is characterized by strongly varying
amplitudes, into a constant-amplitude
square-wave voltage for evaluation in the
ECU microcontroller.
26 Sensors Inductive engine-speed (rpm) sensors
Figure 2
1 Tooth
2 Tooth gap
3 Reference mark
Figure 1
1 Permanent magnet
2 Sensor housing
3 Engine block
4 Pole pin
5 Solenoid winding
6 Air gap
7 Trigger wheel with
reference-mark gap
1 2
6
7
3
4
5
S
N
2 cm
Inductive rpm sensor (principle) 1
U
M
Z
0
1
3
8
-
2
Y
Time
1
2
3
O
u
t
p
u
t

v
o
l
t
a
g
e
Signal from an inductive rpm sensor 2
U
A
E
0
7
2
7
E
Robert Bosch GmbH
Rotational-speed (rpm) sen-
sors and incremental angle-
of-rotation sensors
Application
The above sensors are installed in distribu-
tor injection pumps with solenoid-valve
control. Their signals are used for:
The measurement of the injection pumps
speed,
Determining the instantaneous angular
position of pump and camshaft,
Measurement of the instantaneous setting
of the timing device.
The pump speed at a given instant is one of
the input variables to the distributor pumps
ECU which uses it to calculate the triggering
time for the high-pressure solenoid valve,
and, if necessary, for the timing-device sol-
enoid valve.
The triggering time for the high-pressure
solenoid valve must be calculated in order to
inject the appropriate fuel quantity for the
particular operating conditions. The cam
plates instantaneous angular setting defines
the triggering point for the high-pressure sol-
enoid valve. Only when triggering takes place
at exactly the right cam-plate angle, can it be
guaranteed that the opening and closing
points for the high-pressure solenoid valve are
correct for the particular cam lift. Precise trig-
gering defines the correct start-of-injection
point and the correct injected fuel quantity.
The correct timing-device setting as
needed for timing-device control is ascer-
tained by comparing the signals from the
camshaft rpm sensor with those of the an-
gle-of-rotation sensor.
The rpm sensor, or the angle-of-rotation
sensor, scans a toothed pulse disc with 120
teeth which is attached to the distributor
pumps driveshaft. There are tooth gaps, the
number of which correspond to the number
of engine cylinders, evenly spaced around
the discs circumference. A double differen-
tial magnetoresistive sensor is used.
Magnetoresistors are magnetically con-
trollable semiconductor resistors and similar
in design to Hall-effect sensors.
The double differential sensor has four re-
sistors connected to form a full bridge cir-
cuit. The sensor has a permanent magnet,
the magnet pole face opposite the toothed
pulse disc being homegenized by a thin fer-
romagnetic wafer on which are mounted the
four magnetoresistors, separated from each
other by half a tooth gap. This means that
alternately there are two magnetoresistors
opposite tooth gaps and two opposite teeth
(Fig. 1). The magnetoresistors for automo-
tive applications are designed for operation
in temperatures of 170C (200C briefly).
Sensors Rotational-speed (rpm) sensors and incremental angle-of-rotation sensors 27
Figure 2
1 Flexible conductive
strip
2 Rotational-speed
(rpm)/angle-of-rota-
tion sensor
3 Tooth gap
4 Toothed pulse disc
(trigger wheel)
5 Rotatable mounting
ring
6 Driveshaft
Figure 1
1 Magnet
2 Homogenization
wafer (Fe)
3 Magnetoresistor
4 Toothed pulse disc
1
2
4
3
5
3
3
6
3
Rotational-speed/angle-of-rotation sensor (installed)
2
U
M
K
1
5
5
3
-
1
Y
1
N
S
2
4
3
Rotational-speed/angle-of-rotation sensor
1
U
M
K
1
7
7
1
Y
Robert Bosch GmbH
Hall-effect phase sensors
Application
The engines camshaft rotates at half the
crankshaft speed. Taking a given piston on
its way to TDC, the camshafts rotational
position is an indication whether the piston
is in the compression or exhaust stroke. The
phase sensor on the camshaft provides the
ECU with this information.
Hall-effect rod sensors
As the name implies, such sensors (Fig. 2a)
make use of the Hall effect. A ferromagnetic
trigger wheel (with teeth, segments, or per-
forated rotor, Pos. 7) rotates with the
camshaft. The Hall-effect IC (6) is located
between the trigger wheel and a permanent
magnet (5) which generates a magnetic field
perpendicular to the Hall element.
If one of the trigger-wheel teeth (Z) now
passes the current-carrying rod-sensor ele-
ment (semiconductor wafer), it changes the
field strength. This causes the electrons,
which are driven by a longitudinal voltage
across the element, to be deflected perpen-
dicularly to the direction of current (Fig. 1,
angle ).
This results in a voltage signal (Hall volt-
age) in the millivolt range, which is indepen-
dent of the relative speed between sensor
and trigger wheel. The evaluation-electron-
ics stage integrated in the sensors Hall IC
conditions the signal and outputs it in the
form of a rectangular-pulse signal (Fig. 2b
High/Low).
Differential Hall-effect rod sensors
Rod sensors operating as per the differential
principle are provided with two Hall ele-
ments. These elements are offset from each
other either radially or axially (Fig. 3, S1 and
S2), and generate an output signal which is
proportional to the difference in magnetic
flux at the element measuring points. A two-
track perforated plate (Fig. 3a) or a two-
track trigger wheel (Fig. 3b) are needed in
order to generate the opposing signals in the
Hall elements (Fig. 4) as needed for this
measurement.
Such sensors are used when particularly se-
vere demands are made on accuracy. Further
advantages are their relatively wide air-gap
range and good temperature-compensation
characteristics.
28 Sensors Hall-effect phase sensors
Figure 2
a Positioning of sensor
and single-track trig-
ger wheel
b Output signal charac-
teristic U
A
1 Electrical plug-in con-
nection
2 Sensor housing
3 Engine block
4 Seal ring
5 Permanent magnet
6 Hall-IC
7 Trigger wheel with
tooth/segment (Z)
and gap (L)
a Air gap,
Angle of rotation
Figure 1
I Wafer current
I
H
Hall current
I
V
Supply current
U
H
Hall voltage
U
R
Longitudinal volt-
age
B Magnetic induction
Deflection of the
electrons by the
magnetic field
Z
L
U
A
L L
Z
High
Low
Angle of rotation
a
b
a
2

c
m
7
1
S
N
2
3
4
5
6
Hall-effect rod sensor 2
U
M
K
1
7
6
8
E
U
H
+B
U
R
I
V
I
H
I
Hall element (Hall-effect vane switch) 1
U
A
E
0
6
9
9
-
2
Y
Robert Bosch GmbH
Sensors Hall-effect phase sensors 29
Figure 3
a Axial tap-off
(perforated plate)
b Radial tap-off
(two-track trigger
wheel)
1 Electrical plug-in con-
nection
2 Sensor housing
3 Engine block
4 Seal ring
5 Permanent magnet
6 Differential Hall-IC
with Hall elements S1
and S2
7 Perforated plate
8 Two-track trigger
wheel
I Track 1
II Track 2
Figure 4
Output signal Low:
Material (Z) in front of
S1, gap (L) in front of
S2;
Output signal High:
Gap (L) in front of S1,
material (Z) in front of
S2
S
signal width
U
A
L1 L2
Z2 Z3
Z4 Z1
L3 L4
High
Low
90
0
180
270
360
Characteristic curve of the output signal U
A
from a differential Hall-effect rod sensor 4
U
M
K
1
7
7
0
Y
S2
S1
Z L
L Z
Z Z L L
1
7 8
8
S
N
2
5
6
7
S2 S1
S
N
S2
S1 1
S1 a
b
2
S2
3
4
Differential Hall-effect rod sensors 3
U
M
K
1
7
6
9
Y
Robert Bosch GmbH
Half-differential short-
circuiting-ring sensors
Application
The above sensors are applied as position
sensors for travel or angle. They are very
precise and very robust, and are used as
Rack-travel sensors (RWG) for measuring
the control-rack setting in in-line diesel
injection pumps, and as
Angle-of-rotation sensors in the injected-
fuel quantity actuators for diesel distribu-
tor pumps.
These sensors (Figs. 1 and 2) are comprised
of a laminated soft-iron core on each limb of
which are wound a measuring coil and a ref-
erence coil.
When the alternating current (AC) out-
putted by the ECU flows through these coils,
alternating magnetic fields are generated.
The copper short-circuiting rings surround-
ing the limbs of the soft-iron core, though,
screen these against the alternating magnetic
fields. Whereas the reference short-circuiting
rings are fixed in position, the measuring
short-circuiting rings are attached to the
control rack or to the control-collar shaft
(in-line pumps and distributor pumps re-
spectively) and are free to move (control-
rack travel s, and adjustment angle ).
When the measuring short-circuiting ring
moves, the magnetic flux changes and, since
the ECU maintains the current constant
(load-independent current), the voltage
across the coil also changes.
The ratio of the output voltage U
A
to the
reference voltage U
Ref
(Fig. 3) is calculated
by an evaluation circuit. This ratio is pro-
portional to the deflection of the measuring
short-circuiting ring and can be processed
by the ECU. Bending the reference short-cir-
cuiting ring adjusts the characteristic-curve
gradient, and the basic position of the mea-
suring short-circuiting ring defines the zero
point.
30 Sensors Half-differential short-circuiting-ring sensors
Figure 1
1 Soft-iron core
2 Reference coil
3 Reference short-
circuiting ring
4 Control rack
5 Measuring coil
6 Measuring short-
circuiting ring
s Control-rack travel
Figure 2
1 Measuring coil
2 Measuring short-
circuiting ring
3 Soft-iron core
4 Control-collar shaft
5 Reference coil
6 Reference short-
circuiting ring
max
Adjustment angle
for the control-col-
lar shaft
Measured angle
Figure 3
U
A
Output voltage
U
Ref
Reference voltage
U
A
U
Ref
1 3
2
6
4
5
s
Design of the rack-travel sensor
for diesel in-line injection pumps
1
A
mm
Control-rack travel s
Linear range
U

/
U
R
e
f
Voltage ratio as a function of
control-rack travel
3
U
M
K
0
6
4
1
E
60
0
1
5 6
2
m
a
x
U
A
U
Ref
4 3
Design of the half-differential short-circuiting-ring
sensor for diesel distributor pumps
2
U
A
E
0
7
4
6
Y
U
A
E
0
2
9
0
-
1
Y
Robert Bosch GmbH
Nozzle holders with
needle-motion sensor
Application
The start-of-injection point is an important
parameter for optimum diesel-engine oper-
ation. Its evaluation, for instance, permits
load and speed-dependent injection timing,
and/or the control of the exhaust-gas recir-
culation (EGR), as well as diagnosis in the
ECU. Here, a nozzle holder with needle-mo-
tion sensor (Fig. 2) is used which outputs a
signal as soon as the nozzle needle lifts off its
seat.
When the needle lifts, the extended pressure
pin (12) enters the coil (11). The degree to
which it enters the coil (immersion length
X in Fig. 2), determines the strength of the
magnetic flux in the coil. Nozzle-needle
movement causes a change in the coils mag-
netic flux so that a signal voltage is induced
which is proportional to the needles speed
of movement but not to the distance it has
travelled. This signal is processed directly in
the evaluation circuit. When a given thresh-
old voltage is exceeded (Fig. 1), the evalua-
tion circuit uses this as the signal for the
start of injection.
Sensors Nozzle holders with needle-motion sensor 31
2
Y
Detail Y
X
3
1
5
4
6
7
9
10
11
13
12
8
2 cm
Two-spring nozzle holder with needle-motion sensor
for direct-injection (DI) engines
2
U
M
K
1
7
1
8
-
1
Y
a
Start-of-injection
signal
Threshold
voltage
N
e
e
d
l
e

l
i
f
t
S
i
g
n
a
l

v
o
l
t
a
g
e
Crankshaft angle
b
Needle-motion sensor: Signal 1
U
M
K
1
4
2
7
-
1
E
Figure 1
a Needle-lift curve,
b Corresponding sig-
nal-voltage curve at
the coil
Figure 2
11 Nozzle-holder body
12 Needle-motion sen-
sor
13 Spring
14 Guide element
15 Spring
16 Pressure pin
17 Nozzle-retaining nut
18 Connection to the
evaluation circuit
19 Setting pin
10 Contact lug
11 Coil (sensor coil)
12 Pressure pin
13 Spring seat
Robert Bosch GmbH
a
1
3
b c
1
5 cm
10 cm
3
2
1
2
Accelerator-pedal sensors
Application
In conventional engine-management sys-
tems, the driver transmits his/her wishes for
acceleration, constant or lower speed, to the
engine by using the accelerator pedal to in-
tervene mechanically at the throttle plate
(gasoline engine) or injection pump (diesel
engine). Intervention is transmitted from
the accelerator pedal to throttle plate or in-
jection pump by means of a Bowden cable
or linkage.
On todays engine-management systems,
the Bowden cable and/or linkage have been
superseded and the drivers accelerator-
pedal inputs are transmitted to the ECU by
an accelerator-pedal sensor. This registers
the pedal travel, or its angular setting, and
sends this to the engine ECU in the form of
an electrical signal.
The accelerator-pedal module (Fig. 2b
and c) is available as an alternative to the in-
dividual accelerator-pedal sensor (Fig. 2a).
The module is a ready-to-install unit com-
prising accelerator pedal and sensor. Such
modules mean that adjustments on the vehi-
cle have become unnecessary.
Potentiometer-type accelerator-pedal sensor
The heart of the accelerator-pedal sensor is a
potentiometer across which there is a volt-
age which is a function of the accelerator-
pedal setting. In the ECU, a programmed
characteristic curve is used to calculate the
accelerator-pedal travel or its angular setting
from this voltage.
A second (redundant) sensor is incorpo-
rated for diagnosis purposes and for use in
case of malfunction. It is a component part
of the monitoring system. One version of
the accelerator-pedal sensor operates with a
second potentiometer. The voltage across
this potentiometer is always half that across
the first potentiometer. This provides two
independent signals which are used for trou-
ble-shooting (Fig. 1). Instead of the second
potentiometer, another version uses a low-
idle switch which provides a signal for the
ECU when the accelerator pedal is in the
idle position. For automatic-transmission
32 Sensors Accelerator-pedal sensors
Figure 2
a Individual accelera-
tor-pedal sensor
b Top-mounted accel-
erator-pedal module
c Bottom-mounted ac-
celerator-pedal mod-
ule FMP1
1 Sensor
2 Vehicle-specific
pedal
3 Pedal bracket
Figure 1
1 Potentiometer 1
(master poten-
tiometer)
2 Potentiometer 2
(50% of voltage)
Pedal travel approx. 25 mm
O
u
t
p
u
t

v
o
l
t
a
g
e
V
4.75
0.75
1
2
Characteristic curve of an accelerator-pedal
sensor with redundant potentiometer
1
U
A
E
0
7
2
4
E
2 Accelerator-pedal-sensor versions
U
A
E
0
7
2
5
Y
Robert Bosch GmbH
vehicles, a further switch can be incorpo-
rated for a kick-down signal.
Hall-effect angle-of-rotation sensors
This Hall-effect angle-of-rotation sensor
(ARS1) is based on the movable-magnet
principle. It has a measuring range of ap-
prox. 90 (Figs. 3 and 4).
A semicircular permanent-magnet rotor
(Fig. 4, Pos. 1) generates a magnetic flux
which is returned back to the rotor via a
pole shoe (2), two conductive elements (3)
and the magnetically soft shaft (6). In the
process, the amount of flux which is re-
turned through the conductive elements is a
function of the rotors angle of rotation .
There is a Hall-effect sensor (5) located in
the magnetic path of each conductive ele-
ment, so that is it possible to generate a
practically linear characteristic curve in the
measuring range.
On the ARS2 sensor, a simpler design is used
without magnetically soft conductive ele-
ments. Here, a magnet rotates around the
Hall-effect sensor. The path it takes is in the
form of a circular arc. Since only a small sec-
tion of the resulting sinusoidal characteristic
curve features good linearity, the Hall-effect
sensor is located slightly outside the center
of the arc. This causes the characteristic
curve to deviate from its sinusoidal form so
that the linear section of the curve is in-
creased to more than 180 .
Mechanically, this sensor is highly suitable
for installation in an accelerator-pedal mod-
ule (Fig. 5).
Sensors Accelerator-pedal sensors 33
Figure 5
a Installation in
accelerator-pedal
module
b Components
1 Hall-effect sensor
2 Pedal shaft
3 Magnet
Figure 4
1 Rotor
(permanent mag-
net)
2 Pole shoe
3 Conductive ele-
ment
4 Air gap
5 Hall-effect sensor
6 Pedal shaft
(magnetically soft)
Angle of rotation
Figure 3
1 Housing cover
2 Rotor
(permanent mag-
net)
3 Evaluation electron-
ics with Hall-effect
sensor
4 Housing base
5 Return spring
6 Coupling element
(e.g. gear)
1
1
2
2
3
b a
Hall-effect angle-of-rotation sensor ARS2 5
U
A
E
0
7
7
1
Y
a b
c d
1
2 3
6
5
4
4
Hall-effect angle-of-rotation sensor ARS1

(shown with angular settings a...d)
4
U
A
E
0
7
7
0
Y
1
4
5
6
2
3
Hall-effect angle-of-rotation sensor ARS1 3
U
A
E
0
7
6
9
Y
Robert Bosch GmbH
Hot-film air-mass meter
HFM5
Application
For the optimal combustion as needed to
comply with the emission regulations im-
posed by legislation, it is imperative that
precisely the necessary air mass is inducted
as dictated by the engines operating state.
To this end, part of the total air flow which
is actually inducted through the air filter or
the measuring tube is measured by a hot-film
air-mass meter. Measurement is very precise
and takes into account the pulsations and re-
verse flows caused by the opening and closing
of the engines intake and exhaust valves. In-
take-air temperature changes have no effect
upon measuring accuracy.
Design and construction
The housing of the HFM5 hot-film air-mass
meter (Fig. 1, Pos. 5) projects into a measur-
ing tube (2) which, depending upon the en-
gine's air-mass requirements, can have a va-
riety of diameters (for 370...970 kg/h). This
tube is installed in the intake tract down-
stream from the air filter. Plug-in versions
are also available which are installed inside
the air filter.
The most important components in the
sensor are the sensor element (4), situated in
the air intake (8), and the integrated evalua-
tion electronics (3).
Vapor-deposition is used to apply the sen-
sor-element components to a semiconduc-
tor substrate, and the evaluation-electronics
(hybrid circuit) components to a ceramic
substrate. This principle permits a very
compact design. The evaluation electronics
are connected to the ECU through the plug-
in connection (1). The partial-flow measur-
ing tube (6) is shaped so that the air flows
past the sensor element smoothly (without
whirl effects) and back into the measuring
tube via the air outlet (7). This method en-
sures efficient sensor operation even in case
of extreme pulsation, and in addition to for-
ward flow, reverse flows are also detected
(Fig. 2).
Operating concept
The hot-film air-mass meter is a thermal
sensor and operates according to the fol-
lowing principle:
A micromechanical sensor diaphragm (Fig.
3, Pos. 5) on the sensor element (3) is heated
by a central heating resistor and held at a
constant temperature. The temperature
drops sharply on each side of this controlled
heated zone (4).
The temperature distribution on the di-
aphragm is registered by two temperature-
dependent resistors which are attached up-
stream and downstream of the heating resis-
tor so as to be symmetrical to it (measuring
points M
1
, M
2
). Without the flow of incom-
ing air, the temperature characteristic (1) is
the same on each side of the heated zone
(T
1
= T
2
).
34 Sensors Hot-film air-mass meter HFM5
Figure 1
connection
2 Measuring tube or
air-filter housing wall
3 Evaluation electron-
ics (hybrid circuit)
4 Sensor element
5 Sensor housing
6 Partial-flow measur-
ing tube
7 Air outlet for the par-
tial air flow Q
M
8 Intake for partial air
flow Q
M
7
8
2
1
5
4
6
3
1 cm
Q
M
Hot-film air-mass meter HFM5 1
U
M
K
1
7
1
3
-
1
Y
Robert Bosch GmbH
As soon as air flows over the sensor element,
the uniform temperature distribution at the
diaphragm changes (2). On the intake side,
the temperature characteristic is steeper
since the incoming air flowing past this area
cools it off. Initially, on the opposite side
(the side nearest to the engine), the sensor
element cools off. The air heated by the
heater element then heats up the sensor ele-
ment. The change in temperature distribu-
tion leads to a temperature differential (T)
between the measuring points M
1
and M
2
.
The heat dissipated to the air, and therefore
the temperature characteristic at the sensor
element is a function of the air mass flow.
The temperature differential is a measure of
the air mass flow, and is independent of the
absolute temperature of the air flowing past.
Apart from this, the temperature differential
is directional, which means that the air-mass
meter not only registers the mass of the in-
coming air but also its direction.
Due to its very thin micromechanical di-
aphragm, the sensor has a highly dynamic
response (<15 ms), a point which is of par-
ticular importance when the incoming air is
fluctuating heavily.
The resistance differential at the measur-
ing points M
1
and M
2
is converted by the
evaluation electronics integrated in the sen-
sor into an analog signal of 0...5 V which is
suitable for processing by the ECU. Using
the sensor characteristic (Fig. 2) pro-
grammed into the ECU, the measured volt-
age is converted into a value representing the
air mass flow [kg/h].
The shape of the characteristic curve is such
that the diagnosis facility incorporated in
the ECU can detect such malfunctions as an
open-circuit line. A temperature sensor for
auxiliary functions can also be integrated in
the HFM5. It is located on the sensor ele-
ment upstream of the heated zone, and is
not required for measuring the air mass.
For applications on specific vehicles, sup-
plementary functions such as improved sep-
aration of water and contamination are pro-
vided for (inner measuring tube and protec-
tive grid).
Sensors Hot-film air-mass meter HFM5 35
Figure 3
1 Temperature profile
without air flow
across sensor ele-
ment
2 Temperature profile
with air flow across
sensor element
3 Sensor element
4 Heated zone
5 Sensor diaphragm
6 Measuring tube with
air-mass meter
7 Intake-air flow
M
1
, M
2
measuring points
T
1
, T
2
Temperature val-
ues at the mea-
suring points
M
1
and M
2
T Temperature differ-
ential
T2
T1
T
1
2
T
0
3
5
4
7
7
6
T1 =T2
M2
M1
Hot-film air-mass meter: Measuring principle 3
U
M
K
1
6
5
2
Y
0
0
200 400 kg/h 600
5
6
4
3
2
1
V
O
u
t
p
u
t

v
o
l
t
a
g
e
Air-mass flow
Reverse flow
Forward flow
Output voltage of the hot-film air-mass meter as a
function of the partial air mass flowing past it
2
U
M
K
1
6
9
1
E
Robert Bosch GmbH
Planar broad-band Lambda
oxygen sensor LSU4
Application
As its name implies, the broad-band
Lambda sensor is used across a very exten-
sive range to determine the oxygen concen-
tration in the exhaust gas. The figures pro-
vided by the sensor are an indication of the
air-fuel (A/F) ratio in the engines combus-
tion chamber. The excess-air factor is used
when defining the A/F ratio. The broad-
band Lambda sensor is capable of making
precise measurements not only at the stoi-
chiometric point = 1, but also in the lean
range ( > 1) and the rich range ( < 1). In
the range from 0.7 < < ( = air with
21% O
2
) these sensors generate an unmis-
takable, clear electrical signal (Fig. 2).
These characteristics enable the broad-band
Lambda sensor to be used not only in en-
gine-management systems with two-step
control ( = 1), but also in control concepts
with rich and lean air-fuel (A/F) mixtures.
This type of Lambda sensor is also suitable
for the Lambda closed-loop control used
with lean-burn concepts on gasoline en-
gines, as well as for diesel engines, gaseous-
fuel engines and gas-powered central heaters
and water heaters (this wide range of appli-
cations led to the designation LSU: Lambda
Sensor Universal (taken from the German),
in other words Universal Lambda Sensor).
The sensor projects into the exhaust pipe
and registers the exhaust-gas flow from all
cylinders. In a number of systems, several
Lambda sensors are installed for even
greater accuracy. Here, for instance, they are
fitted upstream and downstream of the cat-
alytic converter as well as in the individual
exhaust tracts (cylinder banks).
The LSU4 broad-band Lambda sensor (Fig.
3) is a planar dual-cell limit-current sensor.
It features a zirconium-dioxide measuring
cell (Fig. 1) which is a combination of a
Nernst concentration cell (sensor cell which
functions the same as a two-step Lambda
sensor) and an oxygen pump cell for trans-
porting the oxygen ions.
The oxygen pump cell (Fig. 1, Pos. 8) is so
arranged with respect to the Nernst concen-
tration cell (7) that there is a 10... 50 m dif-
fusion gap (6) between them which is con-
nected to the exhaust gas through a gas-ac-
cess passage (10). A porous diffusion barrier
(11) serves to limit the flow of oxygen mol-
ecules from the exhaust gas.
On the one side, the Nernst concentration
cell is connected to the atmosphere by a ref-
36 Sensors Planar broad-band Lambda oxygen sensors
Figure 1
1 Exhaust gas
2 Exhaust pipe
3 Heater
4 Control electronics
5 Reference cell with
reference-air pas-
sage
6 Diffusion gap
7 Nernst concentra-
tion cell
8 Oxygen pump cell
with internal and ex-
ternal pump elec-
trode
9 Porous protective
layer
10 Gas-access pas-
sage
11 Porous diffusion bar-
rier
I
P
Pump current
U
P
Pump voltage
U
H
Heater voltage
U
Ref
Reference voltage
(450 mV, corres-
ponds to = 1)
U
S
Sensor voltage
10
11
U
Ref
U
H
U
S
U
P
I
P
2 3 4
5 7 8 9
+
6
1
Planar broad-band Lambda sensor (installation in the exhaust pipe and schematic design of the measuring cell) 1
U
M
K
1
2
6
0
-
1
Y
Robert Bosch GmbH
erence-air passage (5), and on the other, it is
connected to the exhaust gas in the diffusion
gap.
The sensor must have heated up to at least
600... 800 C before it generates a usable sig-
nal. It is provided with an integral heater
(3), so that the required temperature is
reached quickly.
Operating concept
The exhaust gas enters the actual measuring
chamber (diffusion gap) of the Nernst con-
centration cell through the pump cells gas-
access passage. In order that the excess-air
factor can be adjusted in the diffusion gap,
the Nernst concentration cell compares the
exhaust gas in the diffusion gap with the
surrounding air in the reference-air passage.
The process as a whole functions as follows:
By applying the pump voltage U
P
across
the pump cells platinum electrodes, oxygen
from the exhaust gas can be pumped
through the diffusion barrier and into or out
of the diffusion gap. With the help of the
Nernst concentration cell, an electronic cir-
cuit in the ECU controls the voltage U
P
across the pump cell in order that the com-
position of the gas in the diffusion gap re-
mains constant at = 1. If the exhaust gas is
lean, the pump cell pumps the oxygen to the
outside (positive pump current). On the
other hand, if it is rich, due to the decompo-
sition of CO
2
and H
2
O at the exhaust-gas
electrode the oxygen is pumped from the
surrounding exhaust gas and into the diffu-
sion gap (negative pump current). Oxygen
transport is unnecessary at = 1 and pump
current is zero. The pump current is propor-
tional to the exhaust-gas oxygen concentra-
tion and is thus a measure for the non-linear
excess-air factor (Fig. 2).
Sensors Planar broad-band Lambda oxygen sensors 37
Figure 3
1 Measuring cell
(combination of
Nernst concentra-
tion cell and oxygen-
pump cell)
2 Double protective
tube
3 Seal ring
4 Seal packing
5 Sensor housing
6 Protective sleeve
7 Contact holder
8 Contact clip
9 PTFE sleeve
10 PTFE shaped sleeve
11 Five connecting
leads
12 Seal ring
2 1 3 4 5 6 8 9 10 11 12 7
1 cm
LSU4 planar broad-band sensor 3
U
M
K
1
6
0
7
Y
Excess-air factor
P
u
m
p

c
u
r
r
e
n
t

I
p
1 2 0.7 3 4
-1
0
1
mA
-2
Pump current I
P
of a broad-band Lambda sensor as
a function of the exhaust-gas excess-air factor
2
U
M
K
1
2
6
6
-
1
E
Robert Bosch GmbH
Digital technology permits the implementa-
tion of a wide range of open and closed-
loop control functions in the vehicle. An ex-
tensive array of influencing variables can be
taken into account simultaneously so that
the various systems can be operated at max-
imum efficiency. The ECU (Electronic Con-
trol Unit) receives the electrical signals from
the sensors, evaluates them, and then calcu-
lates the triggering signals for the actuators.
The control program, the software, is
stored in a special memory and imple-
mented by a microcontroller.
Operating conditions
The ECU is subjected to very high demands
with respect to
Surrounding temperatures (during nor-
mal operation from 40C to between
+60C and +125C)
Resistance to the effects of such materials
as oil and fuel etc.,
Surrounding dampness,
Mechanical loading due for instance to
engine vibration.
Even when cranking the engine with a weak
battery (cold start), the ECU must operate
just as reliably as when operating voltage is
at a maximum (fluctuations in on-board
voltage supply).
To the same degree, very high demands ap-
ply regarding EMC (ElectroMagnetic Com-
patibility) and the limitation of HF interfer-
ence-signal radiation.
More details on the severe standards apply-
ing to the ECU are given in the box at the
end of this Chapter.
The pcb (printed-circuit board) with the
electronic components (Fig. 1) is installed in
a metal case, and connected to the sensors,
actuators, and power supply through a
multi-pole plug-in connector (4). The high-
power driver stages (6) for the direct trigger-
ing of the actuators are integrated in the
ECU case in such a manner that excellent
heat dissipation to the case is ensured.
When the ECU is mounted directly on the
engine, an integrated heat sink is used to
dissipate the heat from the ECU case to the
fuel which permanently flushes the ECU.
This ECU cooler is only used on commercial
vehicles. Compact, engine-mounted hybrid-
technology ECUs are available for even
higher levels of temperature loading.
The majority of the electronic compo-
nents use SMD technology (SMD, Surface-
Mounted Device). Conventional wiring is
only applied at some of the power-electron-
ics components and at the plug-in connec-
tions, so that a particularly space-saving and
weight-saving design can be used.
Data processing
Input signals
In their role as peripheral components, the
actuators and the sensors represent the in-
terface between the vehicle and the ECU in
its role as the processing unit. The ECU re-
ceives the electrical signals from the sensors
through the vehicle's wiring harness and the
plug-in connection. These signals can be of
the following type:
Analog input signals
Within a given range, analog input signals
can assume practically any voltage value. Ex-
amples of physical quantities which are
available as analog measured values are in-
take-air mass, battery voltage, intake-mani-
fold and boost pressure, coolant and intake-
air temperature. An analog/digital (A/D)
converter in the ECU microcontroller con-
38 ECU Data processing
Electronic Control Unit (ECU)
Robert Bosch GmbH
1
2
3
4
3
c
m
8
7
6
5
9
verts these values to the digital values used
by the microprocessor to perform its calcu-
lations. The maximum resolution of these
signals is in steps of 5 mV per bit (approx.
1000 steps).
Digital input signals
Digital input signals only have two states.
They are either high or low (logical 1
and logical 0 respectively). Examples of digi-
tal input signals are on/off switching signals,
or digital sensor signals such as the rota-
tional-speed pulses from a Hall generator or
a magnetoresistive sensor. Such signals are
processed directly by the microcontroller.
Pulse-shaped input signals
The pulse-shaped signals from inductive
sensors containing information on rota-
tional speed and reference mark are condi-
tioned in their own ECU stage. Here, spuri-
ous pulses are suppressed and the pulse-
shaped signals converted into digital
rectangular signals.
Signal conditioning
Protective circuitry is used to limit the input
signals to a permissible maximum voltage.
By applying filtering techniques, the super-
imposed interference signals are to a great
extent removed from the useful signal
which, if necessary, is then amplified to the
permissible input-signal level for the micro-
controller (0... 5V).
Signal conditioning can take place com-
pletely or partially in the sensor depending
upon the sensors level of integration.
Signal processing
The ECU is the system control center, and is
responsible for the functional sequences of
the engine management (Fig. 2, next page).
The closed and open-loop control functions
are executed in the microcontroller. The in-
put signals from the sensors and the inter-
faces to other systems serve as the input
variables, and are subjected to a further
plausibility check in the computer.
ECU Data processing 39
Figure 1
1 Atmospheric-pres-
sure sensor
2 Switched-mode
power supply
(SMPS) with volt-
age stabilization
3 Low-power driver
stage
4 Plug-in connection
5 CAN interface and
general input and
output circuitry (un-
derneath the pcb,
therefore not visible
here)
6 High-power driver
stages
7 ASIC for driver-
stage triggering
8 Booster-voltage
store (Common Rail)
9 Microcontroller core
ECU: Design and construction 1
U
A
E
0
7
3
7
-
1
Y
Robert Bosch GmbH
The output signals are calculated using the
program.
Microcontroller
The microcontroller is the ECUs central
component and controls its operative se-
quence. Apart from the CPU (Central Pro-
cessing Unit), the microcontroller contains
not only the input and output channels, but
also timer units, RAMs, ROMs, serial inter-
faces, and further peripheral assemblies, all
of which are integrated on a single micro-
chip. Quartz-controlled timing is used for
the microcontroller.
Program and data memory
In order to carry out the computations, the
microcontroller needs a program - the soft-
ware. This is in the form of binary numeri-
cal values arranged in data records and
stored in a program memory.
These binary values are accessed by the
CPU which interprets them as commands
which it implements one after the other (re-
fer also to the Chapter Electronic open and
closed-loop control).
This program is stored in a Read-Only
Memory (ROM, EPROM, or Flash-EPROM)
which also contains variant-specific data
(individual data, characteristic curves, and
maps). This is non-variable data which can-
not be changed during vehicle operation. lt
is used to regulate the programs open and
closed-loop control processes.
The program memory can be integrated in
the microcontroller and, depending upon
the particular application, expanded by the
addition of a separate component (e.g. by an
external EPROM or a Flash-EPROM).
ROM
Program memories can be in the form of a
ROM (Read Only Memory). This is a mem-
ory whose contents have been defined per-
manently during manufacture and there-
after remain unalterable. The ROM installed
in the microcontroller only has a restricted
memory capacity, which means that an ad-
ditional ROM is required in case of compli-
cated applications.
Digital
Input signals:
Power supply
Actuators
Analog
Pulse-shaped
Interface to
other systems
Diagnosis interface
EEPROM
Signal
conditioning
Micro-
controller
Driver stages
ECU
M
o
n
i
t
o
r
i
n
g

m
o
d
u
l
e
A/D
converter
CAN
RAM
Flash-
EPROM
Signal processing in the ECU 2
U
M
K
1
5
0
8
-
3
E
Robert Bosch GmbH
EPROM
The data on an EPROM (Erasable Program-
mable ROM) can be erased by subjecting the
device to UV light. Fresh data can then be
entered using a programming unit.
The EPROM is usually in the form of a
separate component, and is accessed by the
CPU through the Address/Data-Bus.
Flash-EPROM (FEPROM)
The Flash-EPROM is often referred to
merely as a Flash. lt can be erased electri-
cally so that it becomes possible to repro-
gram the ECU in the service workshops
without having to open it. In the process, the
ECU is connected to the reprogramming
unit through a serial interface.
lf the microcontroller is also equipped
with a ROM, this contains the programming
routines for the Flash programming. Flash-
EPROMs are available which, together with
the microcontroller, are integrated on a sin-
gle microchip (as from EDC16).
Its decisive advantages have helped the
Flash-EPROM to largely supersede the con-
ventional EPROM.
Variable-data or main memory
Such a read/write memory is needed in or-
der to store such variable data (variables) as
the computational and signal values.
RAM
Instantaneous values are stored in the RAM
(Random Access Memory) read/write mem-
ory. If complex applications are involved, the
memory capacity of the RAM incorporated
in the microcontroller is insufficient so that
an additional RAM module becomes neces-
sary. lt is connected to the ECU through the
Address/Data-Bus.
When the ECU is switched off by turning
the ignition key, the RAM loses its com-
plete stock of data (volatile memory).
EEPROM (also known as the E
2
PROM)
As stated above, the RAM loses its informa-
tion immediately its power supply is re-
moved (e.g. when the "ignition switch " is
turned to OFF). Data which must be re-
tained, for instance the codes for the vehicle
immobilizer and the fault-store data, must
therefore be stored in a non-erasable (non-
volatile) memory. The EEPROM is an elec-
trically erasable EPROM in which (in con-
trast to the Flash-EPROM) every single
memory location can be erased individually.
lt has been designed for a large number of
writing cycles, which means that the
EEPROM can be used as a non-volatile
read/write memory.
ASIC
The ever-increasing complexity of ECU
functions means that the computing powers
of the standard microcontrollers available
on the market no longer suffice. The solu-
tion here is to use so-called ASIC modules
(Application Specific Integrated Circuit).
These IC's are designed and produced in ac-
cordance with data from the ECU develop-
ment departments and, as well as being
equipped with an extra RAM for instance,
and inputs and outputs, they can also gener-
ate and transmit pwm signals (see PWM
signals below).
Monitoring module
The ECU is provided with a monitoring
module. Using a Question and Answer
cycle, the microcontroller and the monitor-
ing module supervise each other, and as
soon as a fault is detected one of them trig-
gers appropriate back-up functions inde-
pendent of the other.
ECU Data processing 41
Robert Bosch GmbH
Output signals
With its output signals, the microcontroller
triggers driver stages which are usually pow-
erful enough to operate the actuators di-
rectly. The driver stages can also trigger spe-
cific relays. The driver stages are proof
against shorts to ground or battery voltage,
as well as against destruction due to electri-
cal or thermal overload. Such malfunctions,
together with open-circuit lines or sensor
faults are identified by the driver-stage IC as
an error and reported to the microcon-
troller.
Switching signals
These are used to switch the actuators on
and off (for instance, for the engine fan).
PWM signals
Digital output signals can be in the form of
pwm (pulse-width modulated) signals.
These are constant-frequency rectangular
signals with variable on-times (Fig. 3), and
are used to shift the actuators to the desired
setting (e.g. EGR valve, fan, heating element,
boost-pressure actuator).
Communication within the ECU
In order to be able to support the microcon-
troller in its work, the peripheral compo-
nents must communicate with it. This takes
place using an address/data bus which, for
instance, the microcomputer uses to issue
the RAM address whose contents are to be
accessed. The data bus is then used to trans-
mit the relevant data. For former automo-
tive applications, an 8-bit structure sufficed
whereby the data bus comprised 8 lines
which together can transmit 256 values si-
multaneously.
The 16-bit address bus commonly used
with such systems can access 65,536 ad-
dresses. Presently, more complex systems de-
mand 16 bits, or even 32 bits, for the data
bus. In order to save on pins at the compo-
nents, the data and address buses can be
combined in a multiplex system. That is,
data and addresses are dispatched through
the same lines but offset from each other
with respect to time.
Serial interfaces with only a single data
line are used for data which need not be
transmitted so quickly (e.g. data from the
fault storage).
EoL programming
The extensive variety of vehicle variants with
differing control programs and data records,
makes it imperative to have a system which
reduces the number of ECU types needed by
a given manufacturer. To this end, the Flash-
EPROM's complete memory area can be
programmed at the end of production with
the program and the variant-specific data
record (this is the so-called End-of-Line, or
EoL, programming). A further possibility is
to have a number of data variants available
(e.g. gearbox variants), which can then be
selected by special coding at the end of the
line (EoL). This coding is stored in an
EEPROM.
Figure 3
a Fixed frequency
b Variable on-time
Time
S
i
g
n
a
l

v
o
l
t
a
g
e
a
b
a
b
PWM signals 3
U
A
E
0
7
3
8
E
Robert Bosch GmbH
ECU Severe demands on the ECU 43
Very severe demands are made on the ECU
Basically, the ECU in the vehicle functions the
same as a conventional PC. Data is entered
from which output signals are calculated. The
heart of the ECU is the printed-circuit board
(pcb) with microcontroller using high-precision
microelectronic techniques. The automotive
ECU though must fulfill a number of other
requirements.
Real-time compatibility
Systems for the engine and for road/traffic safe-
ty demand very rapid response of the control,
and the ECU must therefore be "real-time com-
patible". This means that the control's reaction
must keep pace with the actual physical
process being controlled. lt must be certain that
a real-time system responds within a fixed peri-
od of time to the demands made upon it. This
necessitates appropriate computer architecture
and very high computer power.
Integrated design and construction
The equipments weight and the installation
space it requires inside the vehicle are becom-
ing increasingly decisive. The following tech-
nologies, and others, are used to make the ECU
as small and light as possible:
Multilayer: The printed-circuit conductors are
between 0.035 and 0.07 mm thick and are
stacked on top of each other in layers.
SMD components are very small and flat
and have no wire connections through holes
in the pcb. They are soldered or glued to the
pcb or hybrid substrate, hence SMD (Sur-
face Mounted Devices).
ASIC: Specifically designed integrated com-
ponent (Application-Specific Integrated Cir-
cuit) which can combine a large number of
different functions.
Operational reliability
Very high levels of resistance to failure are pro-
vided by integrated diagnosis and redundant
mathematical processes (additional processes,
usually running in parallel on other program
paths).
Environmental influences
Notwithstanding the wide range of environmen-
tal influences to which it is subjected, the ECU
must always operate reliably.
Temperature: Depending upon the area of
application, the ECUs installed in vehicles
must perform faultlessly during continual
operation at temperatures between 40C
and +60... 125C. In fact, due to the heat
radiated from the components, the tempera-
ture at some areas of the substrate is consid-
erably higher. The temperature change
involved in starting at cold temperatures and
then running up to hot operating tempera-
tures is particularly severe.
EMC: The vehicle's electronics have to go
through severe electromagnetic compatibility
testing. That is, the ECU must remain com-
pletely unaffected by electromagnetic distur-
bances emanating from such sources as the
ignition, or radiated by radio transmitters and
mobile telephones. Conversely, the ECU
itself must not negatively affect other elec-
tronic equipment.
Resistance to vibration: ECUs which are
mounted on the engine must be able to with-
stand vibrations of up to 30 g (that is, 30
times the acceleration due to gravity).
Sealing and resistance to operating medi-
ums: Depending upon installation position,
the ECU must withstand damp, chemicals
(e.g. oils), and salt fog.
The above factors and other requirements mean
that the Bosch development engineers are con-
tinually faced by new challenges.
Hybrid substrate of an ECU
U
A
E
0
7
4
4
Y
Robert Bosch GmbH
The most important assignment of the Elec-
tronic Diesel Control (EDC) is the control
of the injected fuel quantity and the instant
of injection. The Common Rail accumula-
tor injection system also controls the injec-
tion pressure. Furthermore, on all systems,
the engine ECU also controls a number of
actuators. For all components to operate ef-
fciently, it is imperative that the EDC func-
tions be precisely matched to every vehicle
and every engine (Fig. 1).
Open and closed-loop
electronic control
In both forms of control, one or more input
quantities influence one or more output
quantities
Open-loop control
With open-loop control, the actuators are
triggered by the output signals which the
ECU has calculated using the input vari-
ables, stipulated data, characteristic maps,
and algorithms. The final results are not
checked (open control loop). This principle
is used for instance for the glow-plug se-
quence control.
Closed-loop control
On the other hand, as its name implies,
closed-loop control is characterized by a
closed control loop. Here, the actual value at
the output is continually checked against the
desired value, and as soon as a deviation is
detected this is corrected by a change in the
actuator control. The advantage of closed-
loop control lies in the fact that disturbances
from outside are detected and taken into ac-
count. Closed-loop control is used for in-
stance to control the engines idle speed.
In fact, therefore, the EDC Electronic Con-
trol Unit (ECU) is really an open and
closed-loop control unit. The term ECU
Electronic Control Unit has become so
widespread though, that it is still used even
though the word control alone is not ex-
plicit enough.
Data processing (DP)
The ECU processes the incoming signals
from the external sensors and limits them to
the permissible voltage level. A number of
the incoming signals are also checked for
plausibility.
Using these input data, together with
stored characteristic curves, the micro-
processor calculates the injections timing
and its duration. This information is then
converted to a signal characteristic which is
aligned to the engines piston movements.
This calculation program is termed the
ECU software.
The required degree of accuracy together
with the diesel engines outstanding dy-
namic response necessitate high-level com-
puting power. The output signals are applied
to output stages which provide adequate
power for the actuators (for instance the
high-pressure solenoid valves for fuel injec-
tion, EGR positioner, or boost-pressure ac-
tuator). Apart from this, a number of other
auxiliary-function components (e.g. glow
relay and air conditioner) are triggered.
Faulty signal characteristics are detected by
the output-stage diagnosis functions. Fur-
thermore, signals are exchanged with other
systems in the vehicle via the interfaces. The
engine ECU monitors the complete injec-
tion system within the framework of a safety
concept.
44 Open and closed-loop electronic control Data processing (DP)
Open and closed-loop electronic control
Robert Bosch GmbH
Open and closed-loop electronic control Data processing (DP) 45
EDC ECU
Demands from
the driver
- Driver input,
- Cruise Control (CC),
- Exhaust brake ...
Exchange of data with
other systems
- Traction Control System (TCS),
- Transmission-shift control,
- Climate control ...
System for electronic
cylinder-charge control
- Supercharging,
- Exhaust-gas recirculation
(EGR).
Actuators
- Electropneumatic transducer
- Continuous-operation
braking system
- Fans, blowers,
- Glow control ...
Air
Fuel
Engine
Sensors and desired-
value generators
- Accelerator-pedal sensor,
- Rotational-speed sensor,
- Switches ...
Closed-loop control
and triggering of the
remaining actuators
CAN
Triggering of the fuel-
injection components
- In-line injection pumps,
- Distributor injection pumps,
- Unit Injector / Unit Pump,
- Common Rail high-pressure
pump and injectors,
- Nozzles and nozzle holders.
Air control loop
Data and information flow
Fuel-injection components
Fuel control loop 1 (fuel-injection components)
Fuel control loop 2 (engine)
Detour by way of the driver
Closed-loop control
of the fuel injection
Electronic Diesel Control (EDC): Basic sequence 1
N
M
K
1
7
9
3
E
Robert Bosch GmbH
Data exchange with other
systems
Fuel-consumption signal
The engine ECU (Fig. 1, Pos. 3) detects the
engine fuel consumption and transmits the
signal via CAN to the instrument cluster, or
to an independent on-board computer (6),
where the driver is informed of the current
fuel consumption and/or the remaining
range with the fuel still in the tank. Older
systems used pulse-width modulation
(pwm) for the fuel-consumption signal.
Starter control
The starter (8) can be triggered from the en-
gine ECU. This ensures that the driver can-
not operate the starter with the engine al-
ready running. The starter only turns long
enough for the engine to have reliably
reached self-sustaining speed. This function
leads to a lighter and thus lower-priced
starter.
Glow control unit
The glow control unit (GZS, 5) receives in-
formation from the engine ECU on when
glow is to start and for how long. It then
triggers the glow plugs accordingly and
monitors the glow process, as well as report-
ing back to the ECU on any faults (diagnosis
function). The pre-glow indicator lamp is
usually triggered from the ECU.
Electronic immobilizer
To prevent unauthorized starting and drive-
off, the engine cannot be started before a
special immobilizer (7) ECU removes the
block from the engine ECU.
Either by remote control or by means of
the glow-plug and starter switch (Ignition
key), the driver can signal the immobilizer
ECU that he/she is authorised to use the ve-
hicle. The immobilizer ECU then removes
the block on the engine ECU so that engine
start and normal operation become possible.
46 Open and closed-loop electronic control Data exchange with other systems
Figure 1
1 ESP ECU
(with ABS and TCS)
2 ECU for transmis-
sion-shift control
3 Engine ECU (EDC)
4 A/C ECU
5 Glow control unit
6 Instrument cluster
with on-board com-
puter
7 Immobilizer ECU
8 Starter
9 Alternator
10 A/C compressor
1
2
3
4
9
5
6
7
8
10
Possible components involved in the exchange of data with the Electronic Diesel Control (EDC) 1
U
A
E
0
7
7
7
Y
Robert Bosch GmbH
External torque intervention
In the case of external torque intervention,
the injected fuel quantity is influenced by
another (external) ECU (for instance the
ECU for transmission shift, or for TCS).
This informs the engine ECU whether the
engine torque is to be changed, and if so, by
how much (this defines the injected fuel
quantity).
Alternator control
By means of a standard serial interface, the
EDC can remotely control and remotely
monitor the alternator (9). The regulator
voltage can be controlled, just the same as
the complete alternator assembly can be
switched off. In case of a weak battery for in-
stance, the alternators charging characteris-
tic can be improved by increasing the idle
speed. It is also possible to perform simple
alternator diagnosis through this interface.
Air conditioner
In order to maintain comfortable tempera-
tures inside the vehicle when it is very hot
outside, the air conditioner (A/C) cools
down the air with the help of a refrigerating
compressor (10). Depending upon the en-
gine and the operating conditions, the A/C
compressor can need as much as 30% of the
engines output power.
Immediately the driver hits the accelerator
pedal (in other words he/she wishes maxi-
mum torque), the compressor can be
switched off briefly by the engine ECU, so
that all the engines power is available at the
wheels. Since the compressor is only
switched off very briefly, this has no notice-
able effect upon the passenger-compartment
temperature.
Open and closed-loop electronic control Data exchange with other systems 47
Where does the word Electronics come from?
This term really originates from the ancient
Greeks. They used the word electron for "am-
ber" whose forces of attraction for wool and
similar materials had already been described
by Thales von Milet 2,500 years ago.
The term electronics originates directly from
the word electrons. The electrons, and
therefore electronics as such, are extremely
fast due to their very small mass and their
electrical charge.
The mass of an electron has as little effect
on a gram of any given substance as a 5 gram
weight has on the total mass of our earth.
Incidentally, the word electronics is a prod-
uct of the 20th century. There is no evidence
available as to when the word was used for
the first time. Sir John Ambrose Fleming, one
of the inventors of the electron tube could
have used it around 1902.
The first Electronic Engineer though goes
back to the 19th century. He was listed in the
1888 Edition of a form of Whos Who, pub-
lished during the reign of Queen Victoria. The
official title was Kellys Handbook of Titled,
Landed and Official Classes. The Electronic
Engineer is to be found under the heading
Royal Warrant Holders, that is the list of per-
sons who had been awarded a Royal Warrant.
And what was this Electronic Engineers
job? He was responsible for the correct func-
tiong and cleanliness of the gas lamps at
court. And why did he have such a splendid ti-
tle ? Because he knew that Electrons in an-
cient Greece stood for glitter, shine, and
sparkle.
Source:
Basic Electronic Terms (Grundbegriffe der
Elektronik) Bosch publication (reprint from
the Bosch Znder (Bosch Company News-
paper))..
Robert Bosch GmbH
Fuel-injection control
An overview of the various control func-
tions which are possible with the EDC con-
trol units is given in Table 1. Fig. 1 opposite
shows the sequence of fuel-injection calcula-
tions with all functions, a number of which
are special options. These can be activated in
the ECU by the workshop when retrofit
equipment is installed.
In order that the engine can run with opti-
mal combustion under all operating condi-
tions, the ECU calculates exactly the right
injected fuel quantity for all conditions.
Here, a number of parameters must be taken
into account. On a number of solenoid-
valve-controlled distributor pumps, the sol-
enoid valves for injected fuel quantity and
start of injection are triggered by a separate
pump ECU (PSG).
48 Open and closed-loop electronic control Diesel-injection control
Table 1
1 Only control-sleeve
in-line injection
pumps
2 Passenger cars only
3 Commercial vehicles
only
EDC variants for road vehicles: Overview of functions 1
Fuel-injection system In-line injection
pumps
PE
Helix-controlled
distributor
injection pumps
VE-EDC
Solenoid-valve-
controlled
distributor
injection pumps
VE-M, VR-M
Unit Injector
System and
Unit Pump
System
UIS, UPS
Common Rail
System
CR
Function
Injected-fuel-quantity limitation
3

Vehicle-speed limitation
3

Vehicle-speed control
(Cruise Control)
Altitude compensation
Boost-pressure control
Idle-speed control
Intermediate-speed control
3

Active surge damping
2

BIP control
Intake-tract switch-off
2
Electronic immobilizer
2

Controlled pilot injection
2
Glow control
2

2
A/C switch-off
2

Auxiliary coolant heating
2

Cylinder-balance control
2

Control of injected fuel
quantity compensation
2

Fan (blower) triggering
EGR control
2

2
Start-of-injection control
with sensor
1, 3

Cylinder shutoff
3
3
Robert Bosch GmbH
Open and closed-loop electronic control Diesel-injection control 49
Accelerator-pedal sensor
(driver input)
Inputs
Calculations
Triggering
Vehicle-speed controller
(Cruise Control),
vehicle-speed limiter
Inputs from
other systems
(e.g. ABS, TCS, ESP)
CAN
Start
Switch
Drive mode
Start quantity
Fuel-quantity metering
(pump map)
Timing-device
triggering
Solenoid-valve
triggering
Pump ECU
triggering
Control of start of injection,
and/or start of delivery
Selection of the required
injected fuel quantity
Injected-fuel-quantity limit
+
/-
+
+
Idle-speed controller,
or controller for injected-fuel-
quantity compensation
Active surge damper Smooth-running controller
Calculation of fuel-injection process in the ECU 1
N
M
K
1
7
5
5
E
Robert Bosch GmbH
Start quantity
For starting, the injected fuel quantity is cal-
culated as a function of coolant temperature
and cranking speed. Start-quantity signals
are generated from the moment the starting
switch is turned (Fig. 1, switch in Start po-
sition) until a given minimum engine speed
is reached.
The driver cannot influence the start quan-
tity.
Drive mode
When the vehicle is being driven normally,
the injected fuel quantity is a function of the
accelerator-pedal setting (accelerator-pedal
sensor) and of the engine speed (Fig. 1,
switch in Drive position). Calculation de-
pends upon maps which also take other in-
fluences into account (e.g. fuel and intake-
air temperature). This permits best-possible
alignment of the engines output to the dri-
vers wishes.
Idle-speed control
When the accelerator is not depressed, it is
the job of the idle-speed control to ensure
that a given idle speed is maintained. This
can vary depending upon the engines par-
ticular operating mode. For instance, with
the engine cold the idle speed is usually set
higher than when it is warm. There are fur-
ther instances when the idle speed is held
somewhat higher. For instance when the ve-
hicles electrical-system voltage is too low,
when the air-conditioner is switched on, or
when the vehicle is rolling freely. When the
vehicle is driven in stop-and-go traffic, to-
gether with stops at traffic lights, the engine
runs a lot of the time at idle. Considerations
concerning emissions and fuel consumption
dictate therefore that idle speed should be
kept as low as possible. This of course is a
disadvantage with respect to smooth-run-
ning and pull-away.
When adjusting the stipulated idle speed,
the idle-speed control must cope with heav-
ily fluctuating requirements. The input
power needed by the engine-driven auxiliary
equipment varies extensively.
At low electrical-system voltages for in-
stance, the alternator consumes far more
power than it does when the voltages are
higher. In addition, the power demands
from the A/C compressor, the steering
pump, and the high-pressure generation for
the diesel injection system must all be taken
into account. Added to these external load
moments is the engines internal friction
torque which is highly dependent upon en-
gine temperature, and which must also be
compensated for by the idle-speed control.
In order to regulate the desired idle speed,
the controller continues to adapt the in-
jected fuel quantity until the actual engine
speed corresponds to the desired idle speed.
Maximum-rpm control
The maximum-rpm control ensures that the
engine does not run at excessive speeds. To
avoid damage to the engine, the engine
manufacturer stipulates a permissible maxi-
mum speed which may only be exceeded for
a very brief period.
Above the rated-power operating point, the
maximum-rpm controller reduces the in-
jected fuel quantity continually, until just
above the maximum-rpm point fuel-injec-
tion stops completely. In order to prevent
engine surge, a ramp function is used to en-
sure that the drop off in fuel injection is not
too abrupt. This becomes all the more diffi-
cult the nearer the rated-power point is to
the maximum-rpm point.
Robert Bosch GmbH
Intermediate-speed control
The intermediate-speed control is used only
for trucks and small commercial vehicles
with auxiliary power take-offs (e.g. for crane
operation) or for special vehicles (e.g. am-
bulances with electrical power generator).
With the control in operation, the engine is
regulated to a load-independent intermedi-
ate speed. With the vehicle stationary, the in-
termediate-speed control is activated via the
Cruise Control operator panel.
A fixed rotational speed can be called up
from the data store at the push of a button.
In addition, this operator panel can be used
for preselecting specific engine speeds. The
intermediate-speed control is also applied
on passenger cars with automated gearboxes
(e.g. Tiptronic) to control the engine speed
during gearshifts.
Vehicle-speed controller
(Cruise Control)
The Cruise Control is taken into operation
when the vehicle is to be driven at a constant
speed. It controls the vehicle speed to that
selected by the driver without him/her need-
ing to press the accelerator pedal. The driver
can input the required speed either through
an operating lever or through the steering-
wheel keypad. The injected fuel quantity is
either increased or decreased until the de-
sired (set) speed is reached.
On some Cruise Control applications, the
vehicle can be accelerated beyond the cur-
rent set speed by pressing the accelerator
pedal. As soon as the accelerator pedal is re-
leased again, the Cruise Control regulates
the speed back down to the previously set
speed.
If the driver depresses the clutch or brake
pedal while the Cruise Control is activated,
the control is terminated. On some applica-
tions, the control can be switched off by the
accelerator pedal.
If the Cruise Control has been switched off,
the driver only needs to shift the lever to the
reactivate setting in order to again select the
last speed which had been set.
The operators controls can also be used for
a step-by-step change of the selected speed.
Vehicle-speed limiter
Variable limitation
The vehicle-speed limiter limits the vehicles
maximum speed to a set value even if the ac-
celerator is depressed further. On very quiet
vehicles, in which the engine can hardly be
heard, this is a particular help for the driver
who can then no longer exceed speed limits
inadvertently.
The vehicle-speed limiter keeps the injected-
fuel quantity down to a limit which is in line
with the selected maximum speed. It can be
switched off by the lever or by the kick-
down switch. In order to again select the last
speed which had been set, the driver only
needs to shift the lever to the reactivate set-
ting. The operators controls can also be
used for a step-by-step change of the se-
lected speed.
Fixed limitation
In a number of countries, fixed maximum
speeds are mandatory for certain classes of
vehicles (for instance, for heavy trucks). The
vehicle manufacturers also limit the maxi-
mum speeds of their heavy vehicles by in-
stalling a fixed speed limit which cannot be
switched off.
In the case of special vehicles, the driver can
also select from a range of fixed, pro-
grammed speed limits (for instance, when
there are workers on the garbage trucks rear
platform).
Robert Bosch GmbH
Sudden engine-torque changes excite the ve-
hicles drivetrain, which as a result goes into
surge oscillation. These oscillations are reg-
istered by the vehicles occupants as unpleas-
ant periodic changes in acceleration (Fig. 2,
a). It it the job of the active surge damper to
reduce them (b). Two separate methods are
used:
In case of sudden changes in the torque
required by the driver (through the accel-
erator pedal), a precisely matched filter
function reduces the drivetrain excitation
(1).
The speed signals are used to detect drive-
train oscillations which are then damped
by an active control. In order to counter-
act the drivetrain oscillations (2), the ac-
tive control reduces the injected fuel
quantity when rotational speed increases,
and increases it when speed drops.
Smooth-running control (SRC)/Control
of injected-fuel-quantity compensation
(MAR)
Presuming the same duration of injection,
not all of the engines cylinders generate the
same torque. This can be due to differences
in cylinder-head sealing, as well as differ-
ences in cylinder friction and in the hy-
draulic injection components. These differ-
ences in torque output lead to rough engine
running and an increase in toxic emissions.
The smooth-running control (SRC), or the
control of injected-fuel-quantity compensa-
tion (MAR), use the resulting rotational-
speed fluctuations when detecting such
torque fluctuations. By selected variation of
the injected fuel quantities at the cylinders
concerned, they compensate for the torque
variation. Here, the rotational speed at a
given cylinder after injection is compared to
a mean speed. If the particular cylinders
speed is too low the injected fuel quantity is
increased, and if it is too high the fuel quan-
tity is reduced (Fig. 3).
Figure 2
a Without active surge
damper
b With active surge
damper
1 Filter function
2 Active correction
Time t
I
n
j
e
c
t
e
d

f
u
e
l

q
u
a
n
t
i
t
y
E
n
g
i
n
e

s
p
e
e
d

n
800
20
12
0 1
1+2
b
a
b
a
2 s
25
1000
min
-1
mm
3
1
2
Active surge damper (ARD): Example 2
N
M
K
1
5
5
7
-
1
E
800 min
-1
Actual speed:
Cyl. 1 Cyl. 2 Cyl. 3 Cyl. 4
800 min
-1
790 820 790
Injected
fuel
quantity
= + +
Desired
(setpoint) speed:
Smooth-running control (SRC): Example 3
N
M
K
1
7
9
2
E
Robert Bosch GmbH
The smooth-running control is a comfort
function, the primary object of which is to
ensure that the engine runs smoothly in the
vicinity of idle. The injected-fuel-quantity
compensation function is aimed at not only
improving comfort at idle but also at reduc-
ing the emissions in the medium speed
ranges by ensuring identical injected fuel
quantities for all cylinders. On commercial
vehicles, the smooth-running control is also
known as the AZG (adaptive cylinder equal-
ization).
Injected-fuel-quantity limit
There are a number of reasons why the fuel
quantity actually wished for by the driver, or
that which is physically possible, should not
always be injected. The injection of such fuel
quantities could have the following effects:
Excessive emissions,
Excessive soot,
Mechanical overloading due to high
torque or excessive engine speed,
Thermal overloading due to excessive
temperatures of the exhaust gas, coolant,
oil, or turbocharger,
Thermal overloading of the solenoid
valves as a result of them being triggered
too long.
To avoid these negative effects, a number of
input variables (for instance intake-air
quantity, engine speed, and coolant temper-
ature) are used in generating this limitation
figure. The result is that the maximum in-
jected fuel quantity is limited and with it the
maximum torque.
Engine-brake function
When a trucks engine brake is applied, the
injected fuel quantity is either reduced to
zero or the idle fuel quantity is injected. For
this purpose, the ECU registers the setting of
the engine-brake switch.
Altitude compensation
Atmospheric pressure drops along with in-
creasing altitude so that the cylinder is
charged with less combustion air. This
means that the injected fuel quantity must
be reduced accordingly, otherwise excessive
soot will be emitted.
In order that the injected fuel quantity can
be reduced at high altitudes, the atmos-
pheric pressure is measured by the ambient-
pressure sensor in the ECU. Atmospheric
pressure also has an effect upon boost-pres-
sure control and torque limitation.
Cylinder shutoff
If less torque is required at high engine
speeds, very little fuel must be injected. As
an alternative, cylinder shutoff can be ap-
plied for torque reduction. Here, half of the
injectors are switched off (commercial-vehi-
cle UIS, UPS and CRS). The remaining in-
jectors then inject correspondingly more
fuel which can be metered with even higher
precision.
When the injectors are switched on and
off, special software algorithms ensure
smooth transitions without noticeable
torque changes.
The start of injection has a critical effect on
power output, fuel consumption, noise, and
emissions. The desired value for start of in-
jection depends on engine speed and in-
jected fuel quantity, and it is stored in the
ECU in special maps. Adaptation is possible
as a function of coolant temperature and
ambient pressure.
Robert Bosch GmbH
Tolerances in manufacture and in the pump
mounting on the engine, together with
changes in the solenoid valve during its life-
time, can lead to slight differences in the sol-
enoid-valve switching times which in turn
lead to different starts of injection. The re-
sponse behaviour of the nozzle-and-holder
assembly also changes over the course of
time. Fuel density and temperature also have
an effect upon start of injection. This must
be compensated for by some form of control
strategy in order to stay within the pre-
scribed emissions limits. The following
closed-loop controls are employed (Table 2):
The start-of-injection control is not needed
with the Common Rail System, since the
high-voltage triggering used in the CRS per-
mits highly reproducible starts of injection.
Closed-loop control using the needle-mo-
tion sensor
The inductive needle-motion sensor is fitted
in an injection nozzle (reference nozzle, usu-
ally cylinder 1). When the needle opens (and
closes) the sensor transmits a pulse (Fig. 4).
The needle-opening signal is used by the
ECU as confirmation of the start of injec-
tion. This means that inside a closed control
loop the start of injection can be precisely
aligned to the desired value for the particu-
lar operating point.
The needle-motion sensors untreated signal
is amplified and interference-suppressed be-
fore being converted to precision square-
wave pulses which can be used to mark the
start of injection for a reference cylinder.
The ECU controls the actuator mecha-
nism for the start of injection (for in-line
pumps the solenoid actuator, and for dis-
tributor pumps the timing-device solenoid
valve) so that the actual start of injection al-
ways corresponds to the desired/setpoint
start of injection.
The start-of-injection signal can only be
evaluated when fuel is being injected and
when the engine speed is stable. During
starting and overrun (no fuel injection), the
needle-motion sensor cannot provide a sig-
nal which is good enough for evaluation.
This means that the start-of-injection con-
trol loop cannot be closed because there is
no signal available confirming the start-of-
injection.
Figure 4
1 Untreated signal from
the needle-motion
sensor (NBF),
2 Signal derived from
the NBF signal,
3 Untreated signal from
the inductive engine-
speed sensor
4 Signal derived from
untreated engine-
speed signal,
5 Evaluated start-of-in-
jection signal
1
2
3
4
5
Time t
Conditioning of the signal from the needle-motion
sensor
N
M
K
0
4
6
6
-
1
E
Closed-loop control
Injection system
C
o
n
t
r
o
l

u
s
i
n
g
n
e
e
d
l
e
-
m
o
t
i
o
n
s
e
n
s
o
r
S
t
a
r
t
-
o
f
-
d
e
l
i
v
e
r
y
c
o
n
t
r
o
l
B
I
P

c
o
n
t
r
o
l
Helix-controlled
distributor pumps
Solenoid-valve-controlled
distributor pumps
Common Rail
Unit Injector/Unit Pump
Start-of-injection control 2
Table 2
4
Robert Bosch GmbH
1
2 3
4
5
On in-line pumps, a special digital current
controller improves the controls accuracy
and dynamic response by aligning the cur-
rent to the start-of-injection controllers set-
point value practically without any delay at
all.
In order to ensure start-of-injection accu-
racy in open-loop-controlled operation too,
the start-of-delivery solenoid in the control-
sleeve actuator mechanism is calibrated to
compensate for the effects of tolerances. The
current controller compensates for the ef-
fects of the temperature-dependent solen-
oid-winding resistance. All these measures
ensure that the setpoint value for current as
derived from the start map leads to the cor-
rect stroke of the start-of-delivery solenoid
and to the correct start of injection.
Start-of-delivery control using the incre-
mental angle/time signal (IWZ)
On the solenoid-valve-controlled distributor
pumps (VP30, VP44), the start of injection
is also very accurate even without the help of
a needle-motion sensor. This high level of
accuracy was achieved by applying position-
ing control to the timing device inside the
distributor pump. This form of closed-loop
control serves to control the start of delivery
and is referred to as start-of-delivery con-
trol. Start of delivery and start of injection
have a certain relationship to each other and
this is stored in the so-called wave-propaga-
tion-time map in the engine ECU.
The signal from the crankshaft-speed sensor
and the signal from the incremental
angle/time system (IWZ signal) inside the
pump, are used as the input variables for the
timing-device positioning control.
The IWZ signal is generated inside the
pump by the rotational-speed or angle-of-
rotation sensor (1) on the trigger wheel (2)
attached to the driveshaft. The sensor shifts
along with the timing device (4) which,
when it changes position, also changes the
position of the tooth gap (3) relative to the
TDC pulse of the crankshaft-speed sensor.
The angle between the tooth gap, or the syn-
chronization pulse generated by the tooth
gap, and the TDC pulse is continually regis-
tered by the pump ECU and compared with
the stored reference value. The difference be-
tween the two angles represents the timing
devices actual position, and this is continu-
ally compared with its setpoint/desired posi-
tion. If the timing-device position deviates,
the triggering signal for the timing-device
solenoid valve is changed until actual and
setpoint position coincide with each other.
Since all cylinders are taken into account,
the advantage of this form of start-of-deliv-
ery control lies in the systems rapid re-
sponse. It has a further advantage in that it
also functions during overrun when no fuel
injection takes place which means that the
timing device can be preset for when the
next injection event occurs.
In case even more severe demands are
made on the accuracy of the start of injec-
tion, the start-of-delivery control can have
an optional start-of-injection control with
needle-motion sensor superimposed upon
it.
Figure 5
1 Rotational-
speed/angle-of-rota-
tion sensor inside
the injection pump
2 Trigger wheel
3 Trigger-wheel tooth
gap
4 Shift due to timing
device
connection
Rotational-speed/Angle-of-rotation sensor for the
IWZ signal
N
A
E
0
7
6
0
Y
5
Robert Bosch GmbH
BIP control
BIP control is used with the solenoid-valve-
controlled Unit Injector System (UIS) and
Unit Pump System (UPS). The start of de-
livery or BIP (Begin of Injection Period)
is defined as the instant in time in which the
solenoid closes. As from this point, pressure
buildup starts in the pump high-pressure
chamber. The nozzle opens as soon as the
nozzle-opening pressure is exceeded, and in-
jection can commence (start of injection).
Fuel metering takes place between start of
delivery and end of solenoid-valve trigger-
ing. This period is termed the delivery pe-
riod.
Since there is a direct connection between
the start of delivery and the start of injec-
tion, all that is needed for the precise control
of the start of injection is information on
the instant of the start of delivery.
So as to avoid having to apply additional
sensor technology (for instance, a needle-
motion sensor), electronic evaluation of the
solenoid-valve current is used in detecting
the start of delivery. Around the expected in-
stant of closing of the solenoid valve, con-
stant-voltage triggering is used (BIP win-
dow, Fig. 6, Pos. 1). The inductive effects
when the solenoid valve closes result in the
curve having a specific characteristic which
is registered and evaluated by the ECU. For
each injection event, the deviation of the so-
lenoid-valve closing point from the theoreti-
cal setpoint is registered and stored, and ap-
plied for the following injection sequence as
a compensation value.
If the BIP signal should fail, the ECU
changes over to open-loop control.
Shutoff
The auto-ignitionprinciple of operation
means that in order to stop the diesel engine
it is only necessary to cut off its supply of fuel.
With EDC (Electronic Diesel Control), the
engine is switched off due to the ECU out-
putting the signal Fuel quantity zero(that
is, the solenoid valves are no longer triggered,
or the control rack is moved back to the zero-
delivery setting).
There are also a number of redundant (sup-
plementary) shutoff paths (for instance, the
electrical shutoff valve (ELAB) on the port-
and-helix controlled distributor pumps).
The UIS and UPS are intrinsically safe, and
the worst thing that can happen is that one
single unwanted injection takes place. Here,
therefore, supplementary shutoff paths are
not needed.
Firgure 6
1 BIP window
2 BIP signal
3 Level of pickup cur-
rent
4 Holding-current level
Time
1
2
4
3
t
S
o
l
e
n
o
i
d
-
v
a
l
v
e

c
u
r
r
e
n
t
M
I
BIP detection 6
N
A
E
0
7
5
1
E
Robert Bosch GmbH
Lambda closed-loop-control
for passenger-car diesel en-
gines
Applications
The lawmakers are continually increasing
the severity of the legislation governing the
exhaust-emission limit values for diesel en-
gines. Apart from the measures taken to op-
timize the engines internal combustion, the
open and closed-loop control of those func-
tions which are relevant with regard to the
exhaust emissions are continuing to gain in
importance. The introduction of the
Lambda closed-loop control opens up im-
mense potential for reducing the diesel en-
gines exhaust emissions.
The broad-band Lambda oxygen sensor in
the exhaust pipe (Fig. 1, Pos. 7) measures the
residual oxygen in the exhaust gas. This is an
indicator for the A/F ratio (excess-air-factor
Lambda l). A high level of signal accuracy is
ensured throughout the sensors service life
by adapting the Lambda-sensor signal dur-
ing actual operations. The Lambda-sensor
signal is used as the basis for a number of
Lambda functions which will be described
in more detail in the following.
A Lambda closed-loop control circuit is im-
perative for the regeneration of NO
X
accu-
mulator-type catalytic converters.
The Lambda closed-loop-control is suitable
Open and closed-loop electronic control Lambda closed-loop control 57
Figure 1
1 Diesel engine
2 Diesel injection com-
ponent (here Com-
mon Rail injector)
3 Throttle valve
4 Hot-film air-mass
meter
5 Exhaust-gas tur-
bocharger (here,
VTG version)
6 Engine ECU for
EDC
7 Broad-band Lambda
oxygen sensor
8 EGR valve
2
3
4
5
7
8
6
-Control
1
System overview of Lambda closed-loop control for passenger-car engines (Example) 1
U
M
A
0
0
3
1
Y
Robert Bosch GmbH
for all passenger-car diesel injection systems
controlled by the EDC16 generation.
Basic functions
Pressure compensation
The untreated Lambda-sensor signal is a
function of the oxygen concentration in the
exhaust gas and of the exhaust-gas pressure
at the sensors installation point. The influ-
ence of the pressure on the sensor signal
must therefore be compensated for.
The pressure-compensation function incor-
porates two maps, one for the exhaust-gas
pressure and one for the pressure-depen-
dence of the lambda sensors output signal.
These two maps are used for the correction
of the sensors output signal with reference
to the particular operating point.
Adaptation
In the overrun (trailing throttle) mode, the
Lambda sensors adaptation takes into ac-
count the deviation of the measured oxygen
concentration from the fresh-air oxygen con-
centration (approx. 21%). As a result, the sys-
tem learns a correction value which at every
engine operating point is used to correct the
measured oxygen concentration. This leads to
a precise, drift-compensated Lambda output
signal throughout the sensors service life.
Lambda-based EGR control
Regarding emissions, compared with the
conventional EGR method based on air
mass, using the Lambda oxygen sensor to
measure the residual oxygen in the exhaust
gas permits a tighter tolerance range for the
complete vehicle fleet. In the MNEFZ (mod-
ified new European driving cycle) exhaust-
gas test, therefore, from the exhaust-emis-
sions viewpoint this equates to an improve-
ment of 10...20% with regard to the fleet as a
whole.
58 Open and closed-loop electronic control Lambda closed-loop control
Engine-rpm sensor
Lambda oxygen
sensor
+
+
-
+ -
Hot-film
air-mass meter
EGR valve
Desired injected
fuel quantity
Calculation of the
actual air mass
using Lambda
Lambda controller
Air-mass controller
Desired
air
mass
ECU Engine
Desired
characteristic map
for EGR
Exhaust-gas recirculation using Lamda closed-loop control (EGR cascade control): Principle of operation 2
U
A
E
0
8
9
8
E
Lambda control loop Further sensor signals
Air-mass control loop

Robert Bosch GmbH
Cascade control
With the cascade control (Fig. 2), the con-
ventional air-mass control loop as used in
present-day series production has a Lambda
control loop superimposed upon it (refer to
the section Control and triggering of the
remaining actuators).
The dynamic response is excellent when air-
mass control is used (that is, the air-mass
meter responds far more quickly). The ex-
ternal Lambda closed-loop control circuit
improves the EGR-system accuracy.
The actual air-mass figure is calculated from
the Lambda oxygen sensor signal and from
the desired value for the injected fuel quan-
tity. The system deviation between the cal-
culated air mass and the desired air mass
taken from the EGR desired-value character-
istic map, is compensated for by the Lambda
controller.
Notwithstanding the change to the calcu-
lated air mass as the reference (command)
variable for the EGR, in its physical effects,
this control architecture acts as a Lambda
closed-loop control (in contrast to the
Lambda closed-loop control used on gaso-
line engines in which the fuel mass is taken
as the reference (command) variable).
Fuel-quantity mean-value adaptation
The fuel-quantity mean-value adaptation
(MMA) provides a precise injected-fuel-
quantity signal for the setpoint generation as
needed for those control loops which are
relevant for exhaust-gas emission (e.g. EGR
control, boost-pressure control, and start-
of-injection control). The MMA operates in
the lower part-load range and determines
the average deviation in the injected fuel
quantity of all cylinders together.
Fig. 3 shows the basic structure of the MMA
and its intervention in the control loops
Engine-rpm sensor
Desired air mass
Lambda oxygen
sensor
Hot-film
air-mass meter
EGR valve
Turbocharger
Injection system
+
+
+
-
-
+
Start-of-injection
control
Desired injected
fuel quantity
Adaptation
characteristic map
ECU Engine
Air-mass controller
Calculating the in-
jected fuel quantity
from Lambda
Characteristic
map for EGR
desired-value
Boost-pressure
control
Fuel-quantity mean-value adaptation in the "indirect control" mode: Principle of operation 3
U
A
E
0
8
9
9
E
Further sensor signals
Robert Bosch GmbH
ECU Engine
Engine-rpm sensor
+
-
+
+
Lambda oxygen
sensor
desired
actual
Hot-film
air-mass meter
Injection system
Smoke-limitation quantity
Calculation of the
preliminary
quantity
Desired-value map
for smoke limitation
Lowest
value
Lambda controller
Calculation of the
injected fuel
quantity
which are relevant for the exhaust-gas emis-
sions.
The Lambda-sensor signal and the air-mass
signal are used in calculating the actually in-
jected fuel mass which is then compared
with the desired injected fuel mass. Differ-
ences are then stored in an adaptation map
in defined learning points. This procedure
ensures that when the operating point ne-
cessitates an injected fuel quantity correc-
tion, this can be implemented without delay
even during dynamic changes of state.
These correction quantities are stored in the
EEPROM of the ECU and are available im-
mediately the engine is started.
Basically speaking, there are two MMA op-
erating modes. These differ in the way they
apply the detected deviations in injected fuel
quantity:
Operating mode: Indirect control
In the indirect control mode (Fig. 3), a
precise desired injected fuel quantity is used
as an input variable in the desired-value
characteristic maps which are relevant for
exhaust emissions. The injected fuel quan-
tity is not corrected during the fuel-meter-
ing process.
Operating mode: Direct control
In the direct control mode, in order that
the amount of fuel actually injected corre-
sponds as closely as possible to the desired
quantity, the fuel-quantity deviation is used
to correct the injected fuel quantity during
the fuel-metering process. In this case, this is
(indirectly) a closed fuel-quantity loop.
60 Open and closed-loop electronic control Lambda closed-loop control
Full-load smoke limitation using the Lambda closed-loop control: Principle of operation
Further sensor signals
U
A
E
0
9
0
0
E
4
Robert Bosch GmbH
Full-load smoke limitation
Fig. 4 shows the block diagram of the con-
trol structure for full-load smoke limitation
using a Lambda oxygen sensor. The objec-
tive here is to determine the maximum
amount of fuel which may be injected with-
out exceeding a given smoke value.
The signals from the air-mass meter and the
engine rpm sensor are applied together with
a smoke-limitation map in determining the
desired Lambda value
DESIRED
. This, in
turn, is applied together with the air mass in
order to calculate the preliminary value for
the maximum permissible injected fuel
quantity.
This form of control is already in series pro-
duction, and has a Lambda closed-loop con-
trol imposed upon it. Using the difference
between
DESIRED
and the actually measured
residual oxygen in
ACTUAL
the Lambda con-
troller calculates the correction fuel quan-
tity. The maximum full-load injected fuel
quantity is the total of the preliminary
quantity and the correction quantity.
This control architecture permits a high
level of dynamic response due to the pilot
control, and improved precision due to the
superimposed Lambda control loop.
Detection of undesirable combustion
During overrun (trailing throttle), if the
Lambda-sensor signal drops below a given,
specially calculated threshold this indicates
that undesirable combustion is taking place.
In this case, the engine can be switched off
by closing a control flap and the EGR valve.
The detection of undesirable combustion
represents an additional engine safeguard
function.
Summary
Using Lambda-based EGR it is possible to
considerably reduce a vehicle fleets exhaust-
gas emissions scatter. Here, either fuel-quan-
tity mean-value adaptation (MMA) can be
used or cascade control.
MMA provides a precise injected-fuel-quan-
tity signal for generating the desired (set-
point) values for the control loops which are
relevant for emissions (for instance, for EGR
control, boost-pressure control, start-of-in-
jection control). The precision of these con-
trol loops is increased as a result.
In addition, the application of Lambda
closed-loop control permits the precise defi-
nition of the full-load smoke quantity as
well as the detection of undesirable combus-
tion in the overrun (trailing throttle) mode.
Furthermore, the Lambda sensors high-pre-
cision signal can be used in a Lambda con-
trol loop for the regeneration of NO
X
cat-
alytic converters.
Robert Bosch GmbH
62 Open and closed-loop electronic control Engine dynamometer
1 Intake air
2 Filter
3 Cold-water supply
4 Hot-water supply
5 Fuel
6 Coolant
7 Heater
8 Quick-change sys-
tem
9 Transfer module for
coolant, water, fuel,
etc.
10 Engine management
(EDC)
11 Intercooler
12 Injection system
13 Engine
14 Triggering and sen-
sor signals
15 Catalytic converter
16 Power supply
17 Interface for mea-
surement tech-
niques
18 Electrical dy-
namometer
19 Accelerator-pedal
actuator
20 Test-bench com-
puter
21 Indicating system
(high-speed angle-
synchronous mea-
sured-value acquisi-
tion)
22 Exhaust-gas analysis
equipment (e.g.
Analysis equipment
for gaseous emis-
sions, opacimeter,
Fourier-transformed
infrared (FTIR) spec-
troscope, mass
spectrometer, parti-
cle-counting system)
23 Dilution tunnel
24 Dilution air
25 Mixing chamber
26 Volume meter
27 Blower
28 Particle sampling
system
29 CVS bag sampling
system
30 Change-over valve
5
2
1
3 4
7
9 15
16
17 8
18 19
20 21
22
23
28
29
30
12
10 11
3
3
6
13
14
30 26
27
25 24
Engine dynamometer
Every injection system is tested using an en-
gine-dynamometer setup featuring a high de-
gree of engine accessibility.
By conditioning intake, air, fuel, and coolant
with respect to temperature and pressure etc.,
it is possible to obtain reproducible test re-
sults.
Increasingly, dynamic tests with rapid load and
rpm changes must be run through in addition
to steady-state tests. Here, test stands with an
electrical dynamometric brake (dynamometer)
are the best solution, as they can also drive
the test specimen (as takes place on the road
during overrun or trailing-throttle operation on
a downhill gradient). Using the appropriate
simulation software, the passenger-car ex-
haust-gas tests demanded by law can then be
run through on the engine dynamometer in-
stead of on the roller-type test bench.
The dynamometer computer (20) is responsi-
ble for the control and monitoring of the en-
gine and the test equipment. It also takes over
data acquisition and data storage. Highly effi-
cient application-engineering work (map mea-
surements) can be carried out with the help of
automation software.
By means of suitable quick-change systems
(8), it is possible to change engine pallets
within about 20 minutes, a feature which in-
creases the dynamometers utilization time.
Engine dynamometer: Basic design
S
W
T
0
0
7
6
Y
Robert Bosch GmbH
Further special adaptations
In addition to those described here, EDC
permits a wide range of other functions. For
instance, these include:
Drive recorder
On commercial vehicles, the Drive Recorder
is used to record the engines operating con-
ditions (for instance, how long was the vehi-
cle driven, under what temperatures and
loads, and at what engine speeds). This data
is used in drawing up an overview of opera-
tional conditions from which, for instance,
individual service intervals can be calcu-
lated.
Special application engineering for
competition trucks
On race trucks, the 160 km/h maximum
speed may be exceeded by no more than
2 km/h. On the other hand, this speed must
be reached as soon as possible. This necessi-
tates special adaptation of the ramp func-
tion for the vehicle-speed limiter.
Adaptations for off-highway vehicles
Such vehicles include diesel locomotives, rail
cars, construction machinery, agricultural
machinery, boats and ships. In such applica-
tions, the diesel engine(s) is/are far more of-
ten run in the full-load range than is the
case with road vehicles (90% full-load oper-
ation compared with 30%). The power out-
put of such engines must therefore be re-
duced in order to ensure an adequate service
life.
The mileage figures which are often used
as the basis for the service interval on road
vehicles are not available for such equip-
ment as agricultural or construction ma-
chinery, and in any case if they were avail-
able they would have no useful significance.
Instead, the Drive Recorder data is used
here.
Port-and-helix-controlled fuel-
injection systems: Triggering
Electronically controlled in-line injection
pumps, PE-EDC
As with the mechanically (flyweight) gov-
erned in-line fuel-injection pumps, the in-
jected fuel quantity here is also a function of
the control-rack position and the engine
speed. The control rack is shifted to the de-
sired position by the linear magnet of the
actuator mechanism directly attached to the
pump (Fig. 1 on the next page, Pos. 3).
On the control-sleeve in-line pump, an
additional electrical actuator in connection
with start-of-injection control can be used
to arbitrarily adjust the injected fuel quan-
tity and the start of delivery. This necessi-
tates an extra actuator mechanism (4).
Triggering the control-rack actuator
mechanism
With the solenoid de-energized, a spring
forces the control rack to the stop position
and thus interrupts the fuel supply. When
the current through the solenoid increases,
the solenoid gradually overcomes the force
of the spring and control-rack travel in-
creases so that more fuel is injected.
This means that the level of current per-
mits the continuous adjustment of control-
rack travel between zero and maximum de-
livery quantity (pwm signal = pulse-width-
modulated signal).
The corresponding pump characteristic map
is programmed into the ECU. Using this map,
and depending on engine speed, the control-
rack travel appropriate to the desired fuel
quantity is calculated. In order to improve
driveability, a control characteristic can be
provided which is familiar from the mechan-
ical (flyweight) RQ and RQV governors.
Using a sensor (rack-travel sensor (RWG)),
the position control in the ECU registers the
actual control-rack setting so that the system
deviation can be calculated.
Open and closed-loop electronic control Special adaptations. Port-and-helix-controlled injection systems: Triggering 63
Robert Bosch GmbH
This enables the position control to quickly
and accurately correct the rack setting.
Triggering of the control-sleeve actuator
mechanism
A power stage which is triggered directly
from the processor with a pwm signal pro-
vides the power needed to energize the start-
of-delivery solenoids. A low-level current
causes minor travel of the start-of-delivery
solenoid, and retards the start of delivery or
start of injection. On the other hand, a high
level of current advances the start-of-deliv-
ery point.
The injected-fuel-quantity controls as ap-
plied to the control-sleeve in-line pumps
and the conventional in-line pumps (both
with EDC) are identical. The more extensive
functional scope in the ECU for the control-
sleeve pump results to a great extent from
expanded programs.
Key stop
The key stop function using the ignition
key supersedes the conventional mechanical
shutoff device. It stops the supply of fuel by
interrupting the power supply to the electri-
cal shutoff valve (ELAB, redundant shutoff
path) and to the control-rack linear sol-
enoids.
Port-and-helix-controlled axial-piston
distributor pumps, VE-EDC
Solenoid actuator for injected-fuel-quantity
control
The solenoid actuator (moving-magnet ac-
tuator) engages the delivery-piston control
collar via a shaft (Fig. 2, Pos. 3). Similar to
the mechanically governed distributor
pumps, the cutoff bores are exposed sooner
or later depending upon the position of the
control collar.
The injected fuel quantity can be continually
varied between zero and maximum. By
means of an angle sensor (Hall short-cir-
cuiting-ring sensor, HDK), information on
the angle of rotation of the actuator, and
therefore on the setting of the control collar
with respect to the cutoff ports, is reported
back to the ECU and used to calculate the
correct fuel quantity as a function of engine
speed.
In the de-energized state, the fuel delivery is
set to zero by return springs on the actuator
mechanism.
64 Open and closed-loop electronic control Port-and-helix-controlled injection systems: Triggering
Figure 1
1 In-line injection
pump
2 Electrical shutoff
valve (ELAB)
3 Control-rack actua-
tor mechanism (in-
jected fuel quantity)
4 Control-sleeve actu-
ator mechanism
(start of delivery)
5 Engine ECU
1
4
2
5
3
PE control-sleeve in-line fuel-injection pumps: Injection-triggering components 1
N
M
K
1
7
5
4
Y
Robert Bosch GmbH
Solenoid valve for start-of-injection control
The pumps internal pressure is proportional
to the pump speed and, similar to the me-
chanical timing device, is effective at the
timing-device piston. This pressure is ap-
plied to the timing-device pressure side and
is modulated by the clocked timing-device
solenoid valve (2). The on/off ratio (ratio of
the solenoids open time to its closed time)
for the triggering of the solenoid valve is
taken from a programmed control map.
A permanently opened solenoid valve (pres-
sure reduction) results in later start-of-injec-
tion points, and with the solenoid valve per-
manently closed (pressure increase) the
start-of-injection points take place earlier. In
between these two extremes, infinite varia-
tion of the on/off ratio can be implemented
by the ECU.
Deviations between actual and desired start-
of-injection points, as detected with the help
of the needle-motion sensor, result in a
change of the on/off ratio for triggering the
timing-device solenoid valve. This ratio is
changed continually until the system devia-
tion is zero, and ensures a dynamic re-
sponse which is comparable to that of the
mechanical start-of-injection adjustment.
Shutoff
As a rule, shutoff is by means of the in-
jected-fuel-quantity actuator (zero fuel de-
livery). The redundant electrical shutoff
valve (ELAB) provides a further degree of
safety (4).
On the distributor pump, the redundant
electrical shutoff valve is mounted on the
upper side of the pumps distributor head.
When switched on (that is, with the engine
running), the solenoid keeps the inlet port
to the high-pressure chamber open (the ar-
mature with sealing cone is pulled in). When
switch off takes place using the "ignition
switch", the solenoid winding is de-ener-
gized and the sealing cone is forced back
onto its seat by a spring so that the inlet port
to the high-pressure chamber is interrupted.
On marine engines, the ELAB is open when
de-energized. This means that the engine
can still run even though the on-board
power supply has failed. Apart from this, the
number of electrical consumers is kept to a
minimum since continuous current aggra-
vates the effects of saltwater corrosion.
Open and closed-loop electronic control Port-and-helix-controlled injection systems: Triggering 65
Figure 2
1 Distributor pump
2 Timing-device sol-
enoid valve (start of
injection)
3 Moving-magnet actu-
ator (injected fuel
quantity)
4 Electric shutoff valve
(ELAB)
5 Engine ECU
5
2
1
3
4
VE-EDC axial-piston distributor pumps: Injection-triggering components 2
N
M
K
1
7
5
6
Y
Robert Bosch GmbH
Solenoid-valve-controlled in-
jection systems: Triggering
The solenoid-valve-controlled injection-sys-
tem family includes the following:
Axial-piston distributor pumps,
VE-M (VP30),
Radial-piston distributor pumps,
VR (VP44),
Common Rail System CRS,
Unit Injector System, UIS
Unit Pump System, UPS
These solenoid-valve-controlled injection
systems are all triggered by similar signals.
The characteristic features of the individual
systems are described in the following sec-
tions, together with the differences between
them and conventional injection systems.
Due to better EMC (ElectroMagnetic
Compatibility) characteristics, the high-
pressure solenoid valves are triggered by
analog signals. Since the triggering signal
must feature steep current edges in order to
ensure narrow tolerances and a high degree
of reproducibility for the injected fuel quan-
tity, this form of triggering makes severe de-
mands on the output stages.
In addition, the triggering process must
ensure a minimum of power loss in the ECU
and in the high-pressure solenoid valve. In
other words, the triggering currents must be
as low as possible.
Irrespective of operating range, injection
control must be extremely accurate in order
that the injection pump and solenoid injec-
tor inject precisely and with a high level of
reproducibility.
The injection system must respond ex-
tremely quickly to changes, which means
that the calculations in the microcontroller
and the triggering-signal implementation in
the output stages must take place at very
high speed. Data processing is therefore re-
ferred to as being real-time compatible
(resolution time 1 s).
Solenoid-valve-controlled distributor
pumps
On the distributor pumps equipped with a
high-pressure fuel-quantity solenoid valve
(VP44 and VP30), a pump ECU (PSG) at-
tached to the pump housing is responsible
for triggering the solenoid valves at the cal-
culated start-of-delivery point (Fig. 1a, Pos.
1a). This takes place in accordance with the
requirements of the engine ECU (6) which
is responsible for the engine and vehicle
functions. The two ECUs communicate with
each other through the CAN bus.
The latest generation of the VP44 system
features only a single ECU (PSG 16) which
has united all the EDC functions in a single
unit, and which is situated directly on the
pump (Fig. 1b, Pos. 1b).
The timing-device solenoid valve (4) used
on the distributor pumps is triggered using a
pulse-width-modulated (pwm) signal. In or-
der to avoid malfunctions due to resonance
effects, the clock frequency is not held con-
stant thoughout the complete rotational-
speed range but instead, at given speed
ranges, it is switched to a different frequency
(window technique).
The high-pressure fuel-quantity solenoid
valve is triggered via current control (Fig. 2)
66 Open and closed-loop electronic control Solenoid-valve-controlled injection systems: Triggering
Figure 1
a With separate pump
and engne ECU
b With integral pump
and engine ECU
1a Pump ECU (PSG5)
1b Pump ECU
(PSG16)
2 Distributor pump
3 Timing device
4 Timing-device sol-
enoid valve
5 High-pressure fuel-
quantity solenoid
valve
6 Engine ECU (MSG)
a
2
3
4
5
2
3
4
5
6
1a
b 1b
CAN
Solenoid-valve-controlled distributor pumps: Injec-
tion-triggering components
1
N
M
K
1
7
6
4
Y
Robert Bosch GmbH
which subdivides the triggering process into
a pickup-current phase (a) of approx. 18 A,
and a holding-current phase (c) of approx.
10 A. At the beginning of the controlled
holding-current phase (after 200... 250 s),
the BIP evaluation circuit detects the sol-
enoid-valve needle closing against the valve
seat (BIP = Beginning of the Injection Pe-
riod).
The latest generation uses the PSG16
pump ECU, and is also provided with a BIP
current (b) between the pickup and hold-
ing-current phases which is at the optimum
level for the BIP detection function.
In order that the pumps injection character-
istics are always reproducible irrespective of
operating conditions, the triggering circuitry
as a whole, and the current control, must be
extremely accurate. Furthermore, they must
keep the power loss in ECU and solenoid
valve down to a minimum.
Defined, rapid opening of the solenoid valve
is required at the end of the injection
process. To this end, high-speed quenching
(d) using a high quenching voltage (1) is ap-
plied at the valve to dissipate the energy
stored in its solenoid.
The solenoid valve can also be used to con-
trol pilot injection (PI) for reduction of
combustion noise. Here, the solenoid valve
is operated ballistically between the PI point
and the MI (main injection) point. In other
words it is only partially opened, which
means that it can be closed again very
quickly. The resulting injection spacing is
very short so that even at high rotational
speeds, adequate cam pitch remains for the
main injection process.
The subdivision into the individual trig-
gering phases is calculated by the microcon-
troller in the pump ECU.
Open and closed-loop electronic control Solenoid-valve-controlled injection systems: Triggering 67
Figure 2
a Pickup-current
phase
b BIP detection
c Holding-current
phase
d High-speed quench-
ing
1 Quenching voltage
a b c
1 1
a b c
Solenoid-valve
current I
U
h
Pilot injection (PI) Main injection (MI)
M
Solenoid-valve
voltage
M
Solenoid-valve
needle lift
M
Time t
d d
High-pressure solenoid valves: Triggering sequence using current control 2
N
A
E
0
7
5
2
E
Robert Bosch GmbH
Common Rail System CRS
In the Common Rail System (CRS), the fuel
pressure in the rail (Fig. 3, Pos. 3) and with it
the injection pressure, are determined by the
rail-pressure valve (Pos. 8), and if required by
a throttle upstream of the high-pressure
pump (1). The injectors (6) high-pressure
solenoid valve (7) defines the injection point
and the duration of injection in accordance
with the various operating parameters. This
means, therefore, that injection pressure is
decoupled from injection point and duration
of injection. Decoupling the injection pres-
sure from injection point and duration of in-
jection means that in addition to the main in-
jection (MI), which is responsible for the gen-
eration of torque, other injection processes
independent of the injection pressure can
also be triggered. On the one hand these are
for the most part pilot injections (PI) with
the principle objective of reducing the com-
bustion noise, and on the other secondary in-
jection processes (post injection (POI))which
serve to reduce exhaust emissions. The in-
jected fuel quantity is the product of injection
pressure and duration of injection.
Post injection involves minute quantities of
fuel. Injection is not carried out individually
at stipulated cylinders, but rather the minute
quantities concerned are added together in
the ECU until the smallest quantity is
reached which can be handled by the injec-
tor. When this is reached, it is injected at the
next possible opportunity.
Rail-pressure control
The permanent pressure in the rail is gener-
ated by a continuously operating high-pres-
sure pump. The closed control loop for the
rail pressure comprises the rail-pressure sen-
sor (4) the engine ECU (5) and the rail-pres-
sure control valve (8).
The microcontroller in the engine ECU
receives the sensor signal and uses it to cal-
culate the desired pressure. This is outputted
to a driver stage which triggers the rail-pres-
sure control valve by means of a pwm signal.
The level of the applied current corresponds
to the desired pressure. The higher the trig-
gering current the higher the rail pressure.
The microcontroller compares the actual
pressure at the sensor with the desired pres-
sure and takes appropriate closed-loop con-
trol action in case of deviation.
In a number of versions, at high speeds
and low levels of required fuel, one of the
high-pressure pumps three pumping ele-
ments can be switched off (element shutoff).
In this case, a triggering current flows
through the element-shutoff solenoid valve.
Switching off one of the elements reduces
the strain on the pump as well as increasing
the engines efficiency.
Figure 3
1 High-pressure pump
2 Element shutoff
valve
3 Rail
4 Rail-pressure sensor
5 Engine ECU (for
higher numbers of
cylinders, it is also
possible to use a
"master slave al-
liance" with 2
ECUs)
6 Injector
7 High-pressure sol-
enoid valve
8 Rail-pressure control
valve
2
1
8
5
7
4
6
3
Common Rail System (CRS): Injection-triggering components 3
N
M
K
1
7
5
8
Y
Robert Bosch GmbH
Injector triggering
In the inoperative mode, the injectors high-
pressure solenoid valve is not triggered and
is therefore closed.
The injector injects when the solenoid
valve opens. Solenoid-valve triggering is
subdivided into five phases (Figs. 4 and 5).
Opening phase
Initially, in order to ensure tight tolerances
and high levels of reproducibility for the in-
jected fuel quantity, the current for opening
the valve features a steep, precisely defined
flank and increases rapidly up to approx.
20 A. This is achieved with a so-called
booster voltage of up to as much as 100 V
which is generated in the ECU and stored in
a capacitor (boost-voltage store). When this
voltage is applied across the solenoid valve,
the current increases several times faster than
it does when only battery voltage is used.
Pickup-current phase
During the pickup-current phase, battery
voltage is applied to the solenoid valve, and
assists in opening it quickly. Current control
limits pickup current to approx. 20 A.
Holding-current phase
In order to reduce the power loss in ECU
and injector, the current is dropped to ap-
prox. 12 A in the holding-current phase. The
energy which becomes available when
pickup current and holding current are re-
duced is routed to the booster-voltage store.
Switch off
When the current is switched off in order to
close the valve, the surplus energy is also
routed to the booster-voltage store.
Recharge
Between the actual injection events, a saw-
tooth waveform is applied to the injectors
which are not injecting (Fig. 5, f
1
). Maxi-
mum current level is so low that there is no
danger of the injector opening. Energy
stored in the solenoid valve as a result is
then routed to the booster-voltage store
(Fig. 5, f
2
), which it recharges until the origi-
nal voltage is reached as required for open-
ing the solenoid valve.
Figure 4
a Opening phase
b Pickup-current
phase
c Transition to holding-
current phase
d Holding-current
phase
e Switch off,
f Recharge
a b c d e f
Solenoid-valve
current I
M
Q
h
M
Injected fuel
quantity
Solenoid-valve
needle lift
Time t
Triggering sequence of a high-pressure solenoid valve for a single injection event 4
N
A
E
0
7
4
3
E
Robert Bosch GmbH
Figure 5
1 Battery
2 Current control
3 Solenoid windings
of the high-pressure
solenoid valves
4 Booster switch
5 Booster-voltage
store (capacitor)
6 Free-wheeling
diodes for energy re-
covery and high-
speed quenching
7 Cylinder selector
switch
I Current flow
a Opening phase
c Transition to
holding-current phase
b Pickup-current phase
1
2 4
5
3
I
I
7
3
6
6
7 I
I
I
I
I
I
I
I
d Holding-current phase
e Switch off
I
I
f
1
Recharge
f
2
Recharge to booster-
voltage store
I
I
I
I
I
I
Common Rail System: Block diagram of the triggering phase in the control for a single cylinder group 5
N
M
K
1
7
5
7
E
Robert Bosch GmbH
Unit Injector Systems and Unit Pump
Systems (UIS/UPS)
The triggering of the high-pressure solenoid
valve places severe demands on the output
stages. Close tolerances and high repro-
ducibility of the injected fuel quantity de-
mand that the triggering signal features a
particularly steep edge.
The Unit Injector and Unit Pump high-pres-
sure solenoid valves are triggered in a similar
manner using current control (Figs. 6
through 8) which divides the triggering
process into the pickup-current phase (a)
and the holding-current phase (c). This
form of triggering permits very fast switch-
ing times and reduces the power loss. For a
brief period between these two phases, con-
stant triggering current is applied to permit
the detection of the solenoid-valve closing
point (refer to section BIP control, b).
In order to ensure high-speed, defined
opening of the solenoid valve at the end of
the injection event, a high voltage is applied
across the terminals (d) for rapid quenching
of the energy stored in the solenoid valve.
The microcontroller is responsible for the
calculation of the individual triggering
phases. An ASIC module (gate array) with
high computing power assists the microcon-
troller by generating two digital triggering
signals (MODE signal and ON signal).
These triggering signals then instruct the
Figure 7
a Pickup current
(commercial-vehicle
UIS/UPS: 12...20 A;
passenger-car UIS:
20 A)
b BIP detection,
c Holding current
(commercial-vehicle
UIS/UPS: 8...14 A;
passenger-car UIS:
12 A)
ing
Figure 6
a Unit Injector System
(UIS) with 2 ECUs
b Unit Pump System
(UPS)
1 Unit Injector (UI)
2 High-pressure sol-
enoid valve
3 Engine ECU
4 Unit Pump (UP)
Time t
Solenoid-valve
current I
M
Switch-on signal
Needle-motion
detection
a b c d
Solenoid-valve
needle lift h
M
High-pressure solenoid valve: Triggering sequences 7
N
A
E
0
7
4
0
-
2
E
3
a
1
2
3
3
b
4
2
CAN
Unit Injector and Unit Pump Systems (UIS/UPS):
Triggering components
6
N
M
K
1
7
9
1
Y
Robert Bosch GmbH
output-stage drivers to generate the required
triggering-current sequence.
Boot-shaped injection characteristic
Future systems will provide the possibility of
a special boot-shaped injection character-
istic (with the main injection (MI) immedi-
ately following the pilot injection (PI Fig. 8).
Here, the solenoid-valve current is held at a
precise intermediate level (approx. 4...6 A,
c
1
) between the pickup-current and hold-
ing-current phases. This leads to the sol-
enoid valve being held in an intermediate
position so that a boot-shaped injection
characteristic is the result.
ECU coupling
The passenger-car Unit Injector System can
also be used on engines with more than 6
cylinders. In order to be able to cope with
the requirement for more driver stages for
injector triggering, and for increased micro-
controller computing power, such engines
can be equipped with two ECUs coupled to-
gether to form a master-slave alliance. Sim-
ilar to the Common Rail System (CRS), the
ECUs are coupled together by means of an
internal CAN-Bus operating at a baud rate
of up to 1 Mbaud (1,000,000 bit/s).
Some of the functions are allocated to a
specific ECU which is then solely responsi-
ble for their processing (for instance, the in-
jected-fuel-quantity compensation). Other
assignments though can be flexibly
processed in this configuration by either of
the ECUs (for instance, the registration of
sensor signals). This configuration cannot
be changed during operation.
Using this master-slave concept, it is pos-
sible to implement both Biturbo control and
active exhaust-gas treatment.
Figure 8
a Pickup current (com-
mercial-vehicle
UIS/UPS: 12...20 A)
b BIP detection
c1 Holding current for
"boot-shaped" injec-
tion characteristic
c2 Holding current
(commercial-vehicle
UIS/UPS: 8...14 A)
ing
Solenoid-valve
current I
M
h
M
p
E
Time t
Injection
pressure
a b c d e
Solenoid-valve
needle lift
Triggering sequences of the high-pressure solenoid valves for the boot-
shaped injection characteristic
8
N
A
E
0
7
4
0
-
1
E
Robert Bosch GmbH
Control and triggering of the
remaining actuators
In addition to the fuel-injection compo-
nents themselves, EDC is responsible for the
control and triggering of a large number of
other actuators. These are used for cylinder-
charge control, or for the control of engine
cooling, or are used in diesel-engine start-
assist systems. Here too, as is the case with
the closed-loop control of injection, the in-
puts from other systems (such as TCS) are
taken into account.
A variety of different actuators are used,
depending upon the vehicle type, its area of
application and the type of fuel injection.
This chapter deals with a number of exam-
ples, and further actuators are covered in the
Chapter Actuators.
A variety of different methods are used for
triggering:
The actuators are triggered directly from
an output (driver) stage in the engine
ECU using appropriate signals (e.g. the
EGR valve).
If high currents are involved (for instance
for fan control), the ECU triggers a relay.
The engine ECU transfers signals to an in-
dependent ECU, which is then used to
trigger or control the remaining actuators
(for instance, for glow control).
The advantage of incorporating all engine-
control functions in the EDC ECU lies in the
fact that not only the injected fuel quantity
and instant of injection can be taken into ac-
count in the engine control concept, but also
other engine functions such as EGR and
boost-pressure control. This leads to a con-
siderable improvement in engine manage-
ment. Apart from this, the engine ECU has a
vast amount of information at its disposal as
needed for other functions (for instance, en-
gine and intake-air temperature as used for
glow control on the diesel engine).
Auxiliary coolant heating
High-performance diesel engines are very
efficient, and under certain circumstances
do not generate enough waste heat to ade-
quately heat the vehicles interior. One solu-
tion for overcoming this problem is to install
auxiliary coolant heating using glow plugs.
Depending upon the power available from
the alternator, this system is triggered in a
number of steps. It is controlled by the en-
gine ECU as used for EDC.
Intake-duct switch-off
In the lower engine-rpm ranges and at idle,
a flap (Fig. 1, Pos. 6) operated by an elec-
tropneumatic transducer closes one of the
intake ducts (5). Fresh air in then only in-
ducted through the turbulence duct (2).
This leads to improved air turbulence in the
lower rpm ranges which in turn results in
more efficient combustion. In the higher
rpm ranges, the engines volumetric effi-
ciency is improved thanks to the open intake
duct (5) and the power output increases as a
result.
Open and closed-loop electronic control Control and triggering of the remaining actuators 73
Figure 1
1 Intake valve
2 Turbulence duct
3 Cylinder
4 Piston
5 Intake duct
6 Flap
1
2
3
4
5
6
Intake-duct switch-off 1
N
M
M
0
5
5
5
Y
Robert Bosch GmbH
Boost-pressure control
Boost-pressure control applied to the ex-
haust-gas turbocharger improves the en-
gines torque curve in full-load operation,
and its exhaust and refill cycle in the part-
load range.The optimum (desired) boost
pressure is a function of engine speed, in-
jected fuel quantity, coolant and fuel tem-
perature, and the surrounding air pressure.
This optimum (desired) boost pressure is
compared with the actual value registered by
the boost-pressure sensor and, in the case of
deviation, the ECU either operates the by-
pass valves electropneumatic transducer or
the guide blades of the VTG (Variable Tur-
bine Geometry) exhaust-gas turbocharger
(refer also to the Chapter Actuators).
Fan triggering
When a given engine temperature is ex-
ceeded, the engine ECU triggers the engine
cooling fan, which continues to rotate for a
brief period after the engine is switched off.
This run-on period is a function of the
coolant temperature and the load imposed
on the engine during the preceding driving
cycle.
Exhaust-gas recirculation (EGR)
In order to decrease the NO
X
emissions, ex-
haust gas is directed into the engines intake
duct through a channel, the cross section of
which can be varied by an EGR valve. The
EGR valve is triggered by an electropneu-
matic transducer or by an electric actuator.
Due to the high temperature of the exhaust
gas and its high proportion of contamina-
tion, it is difficult to precisely measure the
exhaust-gas flow which is recirculated back
into the engine. Control, therefore, takes
place indirectly through an air-mass meter
located in the flow of fresh intake air. The
meters output signal is then compared in
the ECU with the engines theoretical air re-
quirement which has been calculated from a
variety of data (e.g. engine rpm).
The lower the measured mass of the incom-
ing fresh air compared to the theoretical air
requirement, the higher is the proportion of
recirculated exhaust gas.
Currently, EGR is only used on passenger
cars, although work is proceeding on the de-
velopment of a commercial-vehicle version.
If individual input signals should fail, the
ECU is without the important information
it needs for calculations. In such cases, sub-
stitute functions are used. Two examples are
given below:
Example 1: The fuel temperature is needed
for calculation of the injected fuel quantity.
If the fuel-temperature sensor fails, the ECU
uses a substitute value for its calculations.
This must be selected so that excessive soot
formation is avoided, although this can lead
to a reduction of engine power in certain
operating ranges.
Example 2: Should the camshaft sensor fail,
the ECU applies the crankshaft-sensor signal
as a subsitute. Depending on the vehicle
manufacturer, there are a variety of different
concepts for using the crankshaft signal to
determine when cylinder 1 is in the com-
pression cycle. The use of substitute func-
tions leads to engine restart taking slightly
longer.
Substitute functions differ according to ve-
hicle manufacturer, so that many vehicle-
specific functions are possible.
The diagnosis function stores data on all
malfunctions that occur. This data can then
be accessed in the workshop (refer also to
the Chapter Electronic Diagnosis (OBD)).
74 Open and closed-loop electronic control Control and triggering of the remaining actuators
Robert Bosch GmbH
Torque-controlled
EDC systems
The engine-management system is continu-
ally being integrated more closely into the
overall vehicle system. Through the CAN-
Bus, vehicle dynamics systems such as TCS,
and comfort and convenience systems such
as Cruise Control, have a direct influence on
the Electronic Diesel Control (EDC). Apart
from this, much of the information regis-
tered and/or calculated in or by the engine
management system must be passed on to
other ECUs through the CAN-Bus.
In order to be able to incorporate the EDC
even more efficiently in a functional alliance
with other ECUs, and implement other
changes rapidly and effectively, it was neces-
sary to make far-reaching changes to the
newest-generation controls. These changes
resulted in the torque-controlled EDC which
was introduced with the EDC16. The main
feature is the change over of the module in-
terfaces to the parameters as commonly en-
countered in practice in the vehicle.
Engine parameters
Essentially, an IC engines output can be de-
fined using the three parameters: Power P,
rpm n, and torque M.
For 2 diesel engines. Fig. 1 compares typi-
cal curves of torque and power as a function
of engine rpm. Basically speaking, the fol-
lowing formula applies:
P = 2 n M
In other words, it suffices to use the torque
as the reference (command) variable. Engine
power then results from the above formula.
Since power output cannot be measured di-
rectly, torque has turned out to be a suitable
reference (command) variable for engine
management.
Torque control
When accelerating, the driver uses the accel-
erator pedal (sensor) to directly demand a
given torque from the engine. At the same
time, but independent of the drivers re-
quirements, via the interfaces other vehicle
systems submit torque demands resulting
from the power requirements of the particu-
lar component (e.g. air conditioner, alterna-
tor). Using these torque-requirement inputs,
the engine management calculates the out-
put torque to be generated by the engine
and controls the fuel-injection and air-sys-
tem actuators accordingly. This method has
the following advantages:
No single system (for instance, boost pres-
sure, fuel injection, pre-glow) has a direct
effect upon the engine management. This
enables the engine management to also
take into account higher-level optimiza-
tion criteria (such as exhaust emissions
and fuel consumption) when processing
external requirements, and thus control
the engine in the most efficient manner,
Many of the functions which do not di-
rectly concern the engine management
can be designed to function identically for
diesel and gasoline engines.
Extensions to the system can be imple-
mented quickly.
Open and closed-loop electronic control Torque-controlled EDC systems 75
Figure 1
a Year of manufacture
1968
b Year of manufacture
1998
P
o
w
e
r

o
u
t
p
u
t
0
25
50
75
kW
T
o
r
q
u
e
0
0
Engine rpm
1000 2000 3000 4000
100
200
300
Nm
a
b
a
b
min
-1
Example of the torque and power-output curves as
a function of engine speed for two passenger-car
diesel engines with approx. 2.2 l displacement
1
N
M
M
0
5
5
6
E
Robert Bosch GmbH
Engine-management sequence
Fig. 2 shows (schematically) the processing
of the setpoint inputs in the engine ECU. In
order to be able to fulfill their assignments
efficiently, the engine managements control
functions all require a wide range of sensor
signals and information from other ECUs in
the vehicle.
Propulsion torque
The drivers input (that is, the signal from
the accelerator-pedal sensor), is interpreted
by the engine management as the request for
a propulsive torque. The inputs from the
Cruise Control and the Vehicle-Speed Lim-
iter are processed in exactly the same man-
ner.
Following this selection of the desired
propulsive torque, should the situation arise,
the vehicle-dynamics system (TCS, ESP) in-
creases the desired torque value when there
is the danger of wheel lockup and decreases
it when the wheels show a tendency to spin.
Further external torque demands
The drivetrains torque adaptation must be
taken into account (drivetrain transmission
ratio). This is defined for the most part by the
ratio of the particular gear, or by the torque-
converter efficiency in the case of automatic
gearboxes. On vehicles with an automatic-
gearbox, the gearbox control stipulates the
torque requirement during the actual gear
shift. Apart from reducing the load on the
gearbox, reduced torque at this point results
in a comfortable, smooth gear shift. In addi-
tion, the torque required by other engine-
powered units (for instance, air-conditioner
compressor, alternator, servo pump) is deter-
mined. This torque requirement is calculated
either by the units themselves or by the en-
gine management.
Calculation is based on unit power and
rotational speed, and the engine manage-
ment adds up the various torque require-
ments. The vehicles driveability remains un-
changed notwithstanding varying require-
ments from the auxiliary units and changes
in the engines operating status.
Internal torque demands
At this stage, the idle-speed control and the
active surge damper intervene.
For instance, if demanded by the situa-
tion, in order to prevent mechanical dam-
age, or excessive smoke due to the injection
of too much fuel, the torque limitation re-
duces the internal torque requirement. In
contrast to the previous engine-manage-
ment systems, limitations are no longer only
applied to the injected fuel-quantity, but in-
stead, depending upon the required effects,
also to the particular physical quantity in-
volved.
The engines losses are also taken into ac-
count (e.g. friction, drive for the high-pres-
sure pump). The torque represents the en-
gines measurable effects to the outside. The
engine management though can only gener-
ate these effects in conjunction with the cor-
rect fuel injection together with the correct
injection point, and the necessary marginal
conditions as apply to the air-intake system
(e.g. boost pressure and EGR rate). The re-
quired injected fuel quantity is determined
using the current combustion efficiency. The
calculated fuel quantity is limited by a pro-
tective function (for instance, protection
against overheating), and if necessary can be
varied by the smooth-running control
(SRC). During engine start, the injected fuel
quantity is not determined by external in-
puts such as those from the driver, but
rather by the separate start-quantity con-
trol function.
Actuator triggering
Finally, the desired values for the injected
fuel quantity are used to generate the trig-
gering data for the injection pump and/or
the injectors, and for defining the optimum
operating point for the intake-air system.
76 Open and closed-loop electronic control Torque-controlled EDC systems
Robert Bosch GmbH
Open and closed-loop electronic control Torque-controlled EDC systems 77
Driver input:
Selection of the
desired propulsion
torque
Propulsion torque:
Further external torque demands
- Accelerator-pedal
sensor
- Vehicle-speed control
(Cruise Control)
Intake-air system
- Turbocharger,
- EGR ...
Injection system
- Fuel-injection
pump,
- Injectors ...
Inputs:
Actuator triggering
- Boost pressure
- EGR rate,
- ...
External
inputs
Input:
- Start of delivery,
- Timing device,
- Rail pressure,
- ... (depending on system).
Input from the vehicle-
dynamics systems:
Drivetrain transm.
Input from the
gearbox ECU
Coordination of the
drivetrain torque
Start quantity
Engine loading due to
auxiliary units
Coordination of the
propulsion torque
- TCS,
- ESP. Data
exchange
Sensor
signals
Internal
sequences
Data trans-
mission
possible
through CAN
,
Fuel-
quantity
input
Start Drive
mode
Engine efficiency
Fuel-quantity limit
Smooth-running control
Internal torque requirements
Control of the engine
torque
(internal functions)
Idle-speed control
Torque limitation
Engine-management sequence for torque-controlled diesel injection 2
N
M
K
1
7
6
3
E
Robert Bosch GmbH
ECU-integrated diagnostics belong to the
basic scope of electronic engine-manage-
ment systems. During normal vehicle oper-
ation, input and output signals are checked
by monitoring algorithms, and the overall
system is checked for malfunctions and
faults. If faults are discovered in the process,
these are stored in the ECU. When the vehi-
cle is checked in the workshop, this stored
information is retrieved through a serial in-
terface and provides the basis for rapid and
efficient trouble-shooting and repair.
Operating concept
Originally, it was intended that the self-diag-
nosis of the engine-management system
(on-board diagnostics/OBD) should merely
be a help in rapid and efficient fault-finding
in the workshop. Increasingly severe legal
stipulations, and the more wide-ranging
functional scope of the vehicles electronic
systems though, led to the emergence of a
more extensive diagnostics system within
the engine-management system.
Input-signal monitoring
Here, the analysis of the input signals is ap-
plied for monitoring the sensors and their
connection lines to the ECU (Table 1). These
checks serve to uncover not only sensor
faults, but also short-circuits to the battery
voltage U
Batt
and to ground, as well as open
circuits in lines. The following processes are
applied:
Monitoring the sensors power supply.
Checking that the measured values are in-
side the correct range (e.g. engine temper-
ature 40 C...+150 C.
If auxiliary information is available, the
registered value is subjected to a plausibil-
ity check (e.g. the camshaft and/or crank-
shaft speed).
Important sensors (such as the accelera-
tor-pedal sensor) are designed to be re-
dundant which means that their signals
can be directly compared with each other.
Output-signal monitoring
Here, in addition to the connections to the
ECU, the actuators are also monitored. Us-
ing the results of these checks, open-circuits
and short-circuits in the lines and connec-
tions can be detected in addition to actuator
faults. The following processes are applied
here:
Hardware monitoring of the output-sig-
nal circuit using the driver stage. The cir-
cuit is checked for open circuit, and for
short circuits to battery voltage U
Batt
and
to ground.
The actuators influence on the system is
checked for plausibility. In the case of ex-
haust-gas recirculation (EGR) for in-
stance, a check is made whether intake-
manifold pressure is within given limits
and that it reacts accordingly when the ac-
tuator is triggered.
Monitoring ECU communication
As a rule, communication with the other
ECUs takes place via CAN-Bus (Controller
Area Network). The diagnostics integrated
in the CAN module are described in the
Chapter Data transfer between electronic
systems. A number of other checks are also
performed in the ECU. Since most CAN
messages are sent at regular intervals by the
particular ECUs, monitoring the time inter-
vals concerned leads to the detection of ECU
failure.
In addition, when redundant information
is available in the ECU, the received signals
are checked the same as all input signals.
78 Electronic diagnosis Operating concept
Electronic diagnosis
Robert Bosch GmbH
Monitoring the internal ECU functions
In order that the functional integrity of the
ECU is ensured at all times, monitoring
functions are incorporated in the hardware
(e.g. intelligent driver-stage modules) and
in the software.
These check the individual ECU compo-
nents (e.g. microcontroller, Flash-EPROM,
RAM). Many of these checks are performed
immediately the engine is switched on. Dur-
ing normal operations, further checks are
performed regularly so that the failure of a
component is detected immediately. Se-
quences which require extensive computing
capacity (for instance for checking the
EPROM), are run through immediately the
engine is switched off (only possible at pre-
sent on gasoline engines).
This method ensures that the other func-
tions are not interfered with. On the diesel
engine, the switch-off paths are checked in
the same period.
Electronic diagnosis Operating concept 79
Table 1
Monitoring the most important input signals 1
Signal path Monitoring
Accelerator-pedal sensor Check of the power supply and the signal range
Plausibility with regard to a redundant signal
Plausibility with regard to the brakes
Crankshaft-rpm sensor Checking the signal range
Plausibility with the camshaft-rpm sensor
Checking the changes as a function of time (dynamic plausibility)
Engine-temperature sensor Checking the signal range
Logical plausibility as a function of rpm
and injected fuel quantity or engine load
Brake-pedal switch Plausibility with regard to redundant brake contact
Speed signal Checking the signal range
Plausibility with regard to rpm and injected fuel quantity or engine load
EGR positioner Checks for short circuits and open circuits in lines
EGR control
Checking the system's reaction to valve triggering
Battery voltage Checking the signal range
Plausibility with regard to engine rpm (at present, only possible with gasoline (SI) engines)
Fuel-temperature sensor Checking the signal range (at present, only possible with diesel engines)
Boost-pressure sensor Checking the power supply and the signal range
Plausibility with regard to ambient-pressure sensor and/or further signals
Boost-pressure actuator Checking for short circuits and open-circuit lines
Control deviation of boost-pressure control
Air-mass meter Checking the power supply and the signal range
Logical plausibility
Air-temperature sensor Checking the signal range
Logical plausibility with regard to the engine-temperature sensor for instance
Clutch-signal sensor Plausibility with regard to vehicle speed
Ambient-pressure sensor Checking the signal range
Logical plausibility of the intake-manifold-pressure sensor
Robert Bosch GmbH
Dealing with a fault
Fault recognition
When a fault remains in a signal path longer
than a defined period, the signal path is clas-
sified as being defective. Until it is finally
classified as defective, the last valid value is
utilised in the system. Normally, as soon as it
is classified as defective, a substitute func-
tion is triggered (refer to the Chapter
Closed-loop and open-loop electronic con-
trol).
Most faults can be revoked and the signal
path classified as serviceable again provided
the signal path remains without fault for a
defined period of time.
Fault storage
Each fault is stored as a malfunction code in
the non-volatile area of the data memory. In
the fault entry, each malfunction code is ac-
companied by auxiliary information in the
so-called freeze-frame containing the op-
erating and environmental conditions at the
moment the fault occurred (e.g. engine rpm,
engine temperature). Information is also
stored on the fault type (for instance short
circuit, conductor open circuit) and the fault
status (in other words, permanent fault or
sporadic fault).
The lawmaker has prescribed specific mal-
function codes for many of the faults which
have an effect on the vehicles toxic emis-
sions. Further fault information not covered
by legislation can also be stored for retrieval
by the vehicle workshop.
Following storage of the fault entry, the
diagnosis for the system or component con-
cerned continues. If the fault does not occur
again in the further course of the diagnosis
(in other words it was a sporadic fault), it is
then erased from the fault memory provided
that certain conditions are complied with.
Fault retrieval
The faults can be retrieved from the fault
memory with a specified workshop tester
provided by the vehicle manufacturer, or by
using a System Tester (e.g. Bosch KTS500),
or a scan tool. Once the fault information
has been retrieved in the workshop and the
fault repaired, the fault memory can be
cleared again using the tester.
Diagnostic interface
A communication interface is needed for
Off-board testers in order for them to be
able evaluate the On-Board Diagnosis.
This serial interface is mandatory and is de-
fined in ISO 9141 (diagnostic interface
through the K-line). The interface operates
with a transfer rate (baud rate) of between
10 baud and 10 kbaud, and is either a single-
wire interface with common send and re-
ceive lines, or a two-wire interface with sepa-
rate data line (K-line) and initiate line (L-
line). A number of ECUs can be connected
together at a single diagnostic connector.
The tester sends an initiate address to all the
ECUs, one of which recognises this address
and replies with a baud-rate identification
word. Using the interval between the pulse
edges, the tester determines the baud rate,
adjusts itself accordingly and sets up the
communication with the ECUs.
Actuator diagnosis
An actuator diagnosis facility is incorpo-
rated in the ECU so that the workshops can
selectively actuate individual actuators and
check their correct functioning. This test
mode is triggered by the tester and only
functions with the vehicle at standstill, and
with the engine running at below a given
speed or with it stopped. Actuator function-
ing is checked either acoustically (e.g. click-
ing of the valve), visually (e.g. movement of
a flap), or by other uncomplicated methods.
80 Electronic diagnosis Operating concept
Robert Bosch GmbH
On-Board-Diagnostics (OBD)
In the past years there has been a continual
reduction in toxic emissions per vehicle. In
order for the emission limits defined by the
vehicle manufacturers to be maintained dur-
ing continuous in-field operations, it is nec-
essary that the engine and its components
are monitored continually. This was the rea-
son for the lawmaker defining specifications
to regulate the diagnosis scope for the ex-
haust-gas-relevant components and systems
in the vehicle.
1988 marked the coming into force of OBD
I in California, that is, the first stage of
CARB legislation (California Air Resources
Board). All newly registered vehicles in Cali-
fornia were forced to comply with these
statutory regulations. OBD II, that is the sec-
ond stage, came into force in 1994.
Since 1994, in the remaining US States the
laws of the Federal Authority EPA (Environ-
mental Protection Agency) have applied.
The scope of these diagnostics comply for
the most part with the CARB legislation
(OBD II), although the requirements for
compliance with the emissions limits are less
severe.
The OBD adapted to European require-
ments is known as the EOBD and is based
on the EPA-OBD. At present, the EOBD
stipulations are even less severe than those
of the EPA-OBD.
OBD I
The electrical components which are rele-
vant for exhaust-gas emissions are checked
for short circuits and breaks by the first
stage of the CARB-OBD. The resulting elec-
trical signals must remain within the stipu-
lated plausibility limits.
When a fault/error is discovered, the dri-
ver is warned by a lamp in the instrument
cluster. Using on-board devices (for in-
stance, a diagnosis lamp which displays a
blink code), it must be possible to read out
which component has failed.
OBD II
The diagnostic procedure for Stage 2 of the
CARB-OBD is far more extensive than OBD
I. Monitoring no longer stops at the check of
the electrical signals from the components,
but has been extended to include the check
of correct system functioning. For instance,
it is no longer sufficient to check that the
signal from the engine-temperature sensor
does not exceed certain fixed limits. OBD II
registers a fault if the engine temperature re-
mains too low (for instance below 10 C) for
a longer period of time (plausibility check).
OBD II demands that all those systems
and components be checked which in case
of malfunction can lead to a noticeable in-
crease in toxic emissions. In addition, all the
components which are actually used for
OBD must also to be checked, and every de-
tected fault must be stored. The driver must
be warned of malfunctions by a lamp in the
instrument cluster. The stored faults are
then retrieved by testers which are con-
nected for trouble-shooting.
OBD II legislation stipulates the standard-
ization of the information stored in the fault
memory in accordance with the ruling of
the SAE (Society of Automotive Engineers).
The means that provided they comply with
the standards, commercially available testers
can retrieve fault information from the fault
memory (so-called scan tools).
Diagnosis-sequence control
As a rule, the diagnostic functions for all the
systems and components to be tested must
be run through at least once during each ex-
haust-gas test cycle (e.g. ECE/EU test cycle).
Depending on the driving status, the diag-
nostics-system management can dynami-
cally change the order of the diagnosis func-
tions. The target here is that all diagnosis
functions are run through often enough
during everyday operations.
Electronic diagnosis On-Board Diagnostics 81
Robert Bosch GmbH
Todays vehicles are being equipped with a
constantly increasing number of electronic
systems. Along with their need for extensive
exchange of data and information in order
to operate efficiently, the data quantities
and speeds concerned are also increasing
continuously.
For instance, in order to guarantee perfect
driving stability, the Electronic Stability Pro-
gram (ESP) must exchange data with the en-
gine management system and the transmis-
sion-shift control.
System overview
Increasingly widespread application of elec-
tronic communications systems, and elec-
tronic open and closed-loop control sys-
tems, for automotive functions such as
Electronic engine-management (EDC and
Motronic),
Electronic transmission-shift control
(GS),
Antilock braking system (ABS),
Traction control system (TCS),
Electronic Stability Program (ESP),
Adaptive Cruise Control (ACC), and
Mobile multimedia systems together with
their display instrumentation
has made it vital to interconnect the individ-
ual ECUs by means of networks.
The conventional point-to-point exchange
of data through individual data lines has
reached its practical limits (Fig. 1), and the
complexity of current wiring harnesses and
the sizes of the associated plugs are already
very difficult to manage. The limited num-
ber of pins in the plug-in connectors has
also slowed down ECU development work.
To underline this point:
Apart from being about 1 mile long, the
wiring harness of an average middle-class
vehicle already includes about 300 plugs and
sockets with a total of 2000 plug pins. The
only solution to this predicament lies in the
application of specific vehicle-compatible
Bus systems. Here, CAN has established it-
self as the standard.
Serial data transfer (CAN)
Although CAN (Controller Area Network)
is a linear bus system (Fig. 2) specifically de-
signed for automotive applications, it has al-
ready been introduced in other sectors (for
instance, in building installation engineer-
ing).
Data is relayed in serial form, that is, one
after another on a common bus line. All
CAN stations have access to this bus, and via
a CAN interface in the ECUs they can re-
ceive and transmit data through the CAN
bus line. Since a considerable amount of
data can be exchanged and repeatedly ac-
cessed on a single bus line, this networking
results in far fewer lines being needed.
82 Data transfer between electronic systems System overview, serial data transfer (CAN)
Data transfer between
automotive electronic systems
Transmission-shift control
Station 1
Engine management
Station 2
ABS/TCS/ESP
Station 3
Instrument cluster
Station 4
Conventional data transfer 1
U
A
E
0
7
4
5
E
Robert Bosch GmbH
Applications in the vehicle
For CAN in the vehicle there are four areas
of application each of which has different
requirements. These are as follows:
Multiplex applications
Multiplex is suitable for use with applications
controlling the open and closed-loop control
of components in the sectors of body elec-
tronics, and comfort and convenience. These
include climate control, central locking, and
seat adjustment. Transfer rates are typically
between 10 kbaud and 125 kbaud (1 kbaud =
1 kbit/s) (low-speed CAN).
Mobile communications applications
In the area of mobile communications, CAN
networks such components as navigation
system, telephone, and audio installations
with the vehicles central display and operat-
ing units. Networking here is aimed at stan-
dardizing operational sequences as far as
possible, and at concentrating status infor-
mation at one point so that driver distrac-
tion is reduced to a minimum. With this ap-
plication, large quantities of data are trans-
mitted, and data transfer rates are in the 125
kbaud range. It is impossible to directly
transmit audio or video data here.
Diagnosis applications
The diagnosis applications using CAN are
aimed at applying the already existing net-
work for the diagnosis of the connected
ECUs. The presently common form of diag-
nosis using the special K line (ISO 9141)
then becomes invalid. Large quantities of
data are also transferred in diagnostic appli-
cations, and data transfer rates of 250 kbaud
and 500 kbaud are planned.
Real-time applications
Real-time applications serve for the open
and closed-loop control of the vehicle's
movements. Here, such electronic systems as
engine management, transmission-shift con-
trol, and electronic stability program (ESP)
are networked with each other.
Commonly, data transfer rates of between
125 kbaud and 1 Mbaud (high-speed CAN)
are needed to guarantee the required real-
time response.
Bus configuration
Configuration is understood to be the layout
and interaction between the components in
a given system. The CAN bus has a linear
bus topology (Fig. 2) which in comparison
with other logical structures (ring bus
and/or star bus) features a lower failure
probability. If one of the stations fails, the
bus still remains fully accessible to all the
other stations. The stations connected to the
bus can be either ECUs, display devices, sen-
sors, or actuators. They operate using the
Multi-Master principle, whereby the stations
concerned all have equal priority regarding
their access to the bus. It is not necessary to
have a higher-order administration.
Data transfer between electronic systems Serial data transfer (CAN) 83
CAN
Transmission-shift
control
Station 1
Engine
management
Station 2
ABS/TCS/ESP
Station 3
Instrument cluster
Station 4
Linear bus topology 2
U
A
E
0
2
8
3
-
2
E
Robert Bosch GmbH
Content-based addressing
The CAN bus system does not address each
station individually according to its features,
but rather according to its message contents.
It allocates each message a fixed identi-
fier (message name) which identifies the
contents of the message in question (for in-
stance, engine speed). This identifier has a
length of 11 bits (standard format) or 29 bits
(extended format).
With content-based addressing each sta-
tion must itself decide whether it is inter-
ested in the message or not (message filter-
ing Fig. 3). This function can be performed
by a special CAN module (Full-CAN), so
that less load is placed on the ECUs central
microcontroller. Basic CAN modules read
all messages. Using content-based address-
ing, instead of allocating station addresses,
makes the complete system highly flexible so
that equipment variants are easier to install
and operate. If one of the ECUs requires
new information which is already on the
bus, all it needs to do is call it up from the
bus. Similarly, provided they are receivers,
new stations can be connected (imple-
mented) without it being necessary to mod-
ify the already existing stations.
Bus arbitration
The identifier not only indicates the data
content, but also defines the messages prior-
ity rating. An identifier corresponding to a
low binary number has high priority and
vice versa. Message priorities are a function
for instance of the speed at which their con-
tents change, or their significance with re-
spect to safety. There are never two (or
more) messages of identical priority in the
bus.
Each station can begin message transmis-
sion as soon as the bus is unoccupied. Con-
flict regarding bus access is avoided by ap-
plying bit-by-bit identifier arbitration (Fig.
4), whereby the message with the highest
priority is granted first access without delay
and without loss of data bits (nondestruc-
tive protocol).
The CAN protocol is based on the logical
states dominant (logical 0) and recessive
(logical 1). The Wired And arbitration
principle permits the dominant bits trans-
mitted by a given station to overwrite the re-
cessive bits of the other stations. The station
with the lowest identifier (that is, with the
highest priority) is granted first access to the
bus.
84 Data transfer between electronic systems Serial data transfer (CAN)
Figure 3
Station 2 transmits,
Station 1 and 4 accept
the data.
Figure 4
Station 2 gains first
access
(Signal on the bus = sig-
nal from Station 2)
0 Dominant level
1 Recessive level
Provision
Send
message
CAN
Station 1
CAN
Station 2
Bus
CAN
Station 3
CAN
Station 4
Accept
Selection
Reception
Accept
Selection Selection
Reception Reception
Addressing and message filtering (acceptance check) 3
U
A
E
0
2
8
4
-
1
E
Bus line
1
0
Station 1
loses the
arbitration
Station 3
loses the
arbitration
Station 1
1
0
Station 2
1
0
Station 3
1
0
Bit-by-bit arbitration (allocation of bus
access in case of several messages)
4
U
A
E
0
7
4
2
E
Robert Bosch GmbH
The transmitters with low-priority messages
automatically become receivers, and repeat
their transmission attempt as soon as the
bus is vacant again.
In order that all messages have a chance of
entering the bus, the bus speed must be ap-
propriate to the number of stations partici-
pating in the bus. A cycle time is defined for
those signals which fluctuate permanently
(e.g. engine speed).
Message format
CAN permits two different formats which
only differ with respect to the length of their
identifiers. The standard-format identifier is
11 bits long, and the extended-format iden-
tifier 29 bits. Both formats are compatible
with each other and can be used together in
a network. The data frame comprises seven
consecutive fields (Fig. 5) and is a maximum
of 130 bits long (standard format) or 150
bits (extended format).
The bus is recessive at idle. With its domi-
nant bit, the Start of frame indicates the
beginning of a message and synchronises all
stations.
The Arbitration field consists of the mes-
sages identifier (as described above) and an
additional control bit. While this field is be-
ing transmitted, the transmitter accompa-
nies the transmission of each bit with a
check to ensure that it is still authorized to
transmit or whether another station with a
higher-priority message has accessed the
Bus. The control bit following the identifier
is designated the RTR-bit (Remote Trans-
mission Request). It defines whether the
message is a Data frame (message with
data) for a receiver station, or a Remote
frame (request for data) from a transmitter
station.
The Control field contains the IDE bit
(Identifier Extension Bit) used to differenti-
ate between standard format (IDE = 0) and
extended format (IDE = 1), followed by a bit
reserved for future extensions. The remain-
ing 4 bits in this field define the number of
data bytes in the next data field. This enables
the receiver to determine whether all data
has been received.
The Data field contains the actual message
information comprised of between 0 and
8 bytes. A message with data length = 0 is
used to synchronise distributed processes. A
number of signals can be transmitted in a
single message (e.g. engine rpm and engine
temperature).
The CRC Field (Cyclic Redundancy
Check) contains the frame check word for
detecting possible transmission interference.
The ACK Field contains the acknowledge-
ment signals used by the receiver stations to
confirm receipt of the message in non-cor-
rupted form. This field comprises the ACK
slot and the recessive ACK delimiter. The
ACK slot is also transmitted recessively and
overwritten dominantly by the receivers
upon the message being correctly received.
Here, it is irrelevant whether the message is
of significance or not for the particular re-
ceiver in the sense of the message filtering or
acceptance check. Only correct reception is
confirmed.
Data transfer between electronic systems Serial data transfer (CAN) 85
Figure 5
0 Dominant level,
1 Recessive level.
* Number of bits
Data frame
Message frame
Start of Frame
Arbitration Field
Control Field
Data Field
CRC Field
ACK Field
End of
Frame
Inter
Frame
Space
1*
1
0
12* 6* 16* 2* 7* 3* IDLE IDLE 0...64*
CAN message format 5
U
A
E
0
2
8
5
-
1
E
Robert Bosch GmbH
The End of frame marks the end of the
message and comprises 7 recessive bits.
The Inter-frame space comprises three bits
which serve to separate successive messages.
This means that the bus remains in the re-
cessive IDLE mode until a station starts a
bus access.
As a rule, a sending station initiates data
transmission by sending a data frame. It is
also possible for a receiving station to call in
data from a sending station by transmitting
a remote frame.
Detecting errors
A number of control mechanisms for de-
tecting errors are integrated in the CAN pro-
tocol.
In the CRC field, the receiving station
compares the received CRC sequence with
the sequence calculated from the message.
With the Frame check, frame errors are
recognized by checking the frame structure.
The CAN protocol contains a number of
fixed-format bit fields which are checked by
all stations.
The ACK check is the receiving stations
confirmation that a message frame has been
received. Its absence signifies for instance
that a transmission error has been detected.
Monitoring indicates that the sender ob-
serves (monitors) the bus level and com-
pares the differences between the bit that has
been sent and the bit that has been checked.
Compliance with Bitstuffing is checked by
means of the Code check. The stuffing rule
stipulates that in every data frame or re-
mote frame, a maximum of 5 successive
equal-priority bits may be sent between the
Start of frame and the end of the CRC
field. As soon as five identical bits have been
transmitted in succession, the sender inserts
an opposite-priority bit. The receiving sta-
tion erases these opposite-polarity bits after
receiving the message. Line errors can be de-
tected using the bitstuffing principle.
If one of the stations detects an error, it in-
terrupts the actual transmission by sending
an Error frame comprising six successive
dominant bits. Its effect is based on the in-
tended violation of the stuffing rule, and the
object is to prevent other stations accepting
the faulty message.
Defective stations could have a derogatory
effect upon the bus system by sending an
error frame and interrupting faultless
messages. To prevent this, CAN is provided
with a function which differentiates between
sporadic errors and those which are perma-
nent, and which is capable of identifying the
faulty station. This takes place using statisti-
cal evaluation of the error situations.
Standardization
The International Organization for Stan-
dardization (ISO) and SAE (Society of Auto-
motive Engineers) have issued CAN stan-
dards for data exchange in automotive appli-
cations:
For low-speed applications up to
125 kbit/s: ISO 11519-2, and
For high-speed applications above
125 kbit/s: ISO 11898 and SAE J 22584
(passenger cars) and SAE J 1939 (trucks
and buses).
Furthermore, an ISO Standard on CAN
Diagnosis (ISO 15765 Draft) is being
prepared.
86 Data transfer between electronic systems Serial data transfer (CAN)
Robert Bosch GmbH
Prospects
Along with the increasing levels of system-
component performance and the rise in
function integration, the demands made on
the vehicles communication system are also
on the increase. And new systems are con-
tinually being introduced, for instance in the
consumer-electronics sector. All in all, it is to
be expected that a number of bus systems
will establish themselves in the vehicle, each
of which will be characterized by its own
particular area of application.
In addition to electronic data transmission,
optical transmission systems will also come
into use in the multimedia area. These are
very-high-speed bus systems and can trans-
mit large quantities of data as needed for au-
dio and video components.
Individual functions will be combined by
networking to form a system alliance cover-
ing the complete vehicle, in which informa-
tion can be exchanged via data buses. The
implementation of such overlapping func-
tions necessitates binding agreements cover-
ing interfaces and functional contents. The
CARTRONIC
from Bosch is the answer to

these stipulations, and has been developed
as a priority-override and definition concept
for all the vehicles closed and open-loop
control systems. The possible sub-division of
the functions which are each controlled by a
central coordinator can be seen in Fig. 1.
The functions can be incorporated in vari-
ous ECUs.
The combination of components and sys-
tems can result in completely novel func-
tions. For instance, the exchange of data be-
tween the transmission-shift control and the
navigation equipment can ensure that a
change down is made in good time before a
gradient is reached. With the help of the
navigation facility, the headlamps will be
able to adapt their beam of light to make it
optimal for varying driving situations and
for the route taken by the road (for instance
at road intersections). Car radios, sound-
carrier drives, TV, telephone, E-mail, Inter-
net, as well as the navigation and terminal
equipment for traffic telematics will be net-
worked to form a multimedia system.
Data transfer between electronic systems Prospects 87
Functions
Actuators
Sensors
Modules
Bodywork and
interior
On-board
electrical
system
Vehicle coordination
Drive
Vehicle
movement
Mobile
Multimedia
CARTRONIC
: Design schematic 1
U
A
E
0
6
7
4
-
3
E
Robert Bosch GmbH
Actuators convert the electrical output sig-
nals from the ECU into mechanical quanti-
ties (e.g. for setting the EGR valve or the
throttle valve).
Electropneumatic
transducers
EGR valve
With exhaust-gas recirulation (EGR) a por-
tion of the exhaust gas is led back into the
engines intake tract with the object of re-
ducing toxic emissions.
The quantity of exhaust gas directed back
to the engine is controlled by an electrop-
neumatic valve situated between the exhaust
tract and the intake tract. In future, electric
valves will be used for this purpose.
In order to provide for high engine torque at
low engine speeds, the exhaust-gas tur-
bocharger is designed to generate high boost
pressure in this rotational-speed range. To
prevent the generation of excessive boost
pressure at high engine turbocharger speeds,
the boost-pressure controls actuator diverts
some of the exhaust gas around the exhaust-
gas turbochargers turbine by means of a so-
called wastegate (Fig. 1).
Instead of the wastegate, turbines with
variable turbine geometry (VTG) can be
used to adapt the turbochargers output. In
the case of VTG, an electrical or electrop-
neumatic valve varies the angle of the tur-
bine blades in the exhaust-gas passage.
Swirl controller
In the passenger car, swirl control is applied
to influence the swirl motion of the intake
air in the cylinder. The swirl itself is usually
generated by spiral-shaped intake ports.
Since it determines the mixing of fuel and
air in the combustion chamber, it has con-
siderable influence upon combustion qual-
ity. As a rule, a pronounced swirl is gener-
ated at low speeds, and a weak swirl at high
speeds.
The swirl can be modified by the swirl con-
troller (flap or slide valve) near to the intake
valve.
Intake-manifold flap
On the passenger-car UIS, the intake-mani-
fold flap cuts off the supply of air when the
engine is switched off so that less air is com-
pressed and the engine stops smoothly. The
flap is controlled by an electropneumatic
valve.
Throttle valve
The throttle valve is controlled by an elec-
tropneumatic valve, and in the diesel engine
its function is very different to that in the
gasoline engine. On the diesel engine it
serves to increase the EGR rate by reducing
the overpressure in the intake manifold.
Throttle-valve control is only operative in
the lower speed range.
88 Actuators Electropneumatic Transducers
Actuators
Figure 1
1 Boost-pressure ac-
tuator
2 Vacuum pump
3 Pressure actuator
4 Exhaust-gas tur-
bocharger
5 Bypass valve
6 Exhaust-gas flow
7 Intake-air flow
8 Turbine
9 Compressor
1
5
4 8
9
6
7
2
3
Boost-pressure control with boost-pressure actuator 1
U
M
K
1
5
5
1
-
9
Y
Robert Bosch GmbH
Continuous-operation
braking systems
These braking systems are used for reducing
the speed of heavy trucks without causing
wear of the conventional braking compo-
nents. They cannot stop the vehicle though.
Since, in contrast to service brake systems
with friction wheel brakes, they adequately
dissipate the braking heat even when they
are applied over a long period, continuous-
operation braking systems are most suitable
for slowing down the vehicle on extended
downhill gradients. As a result, the friction
brakes are used less and remain cool so that
they can be applied to full effect in an emer-
gency. The continuous-operation braking
system is controlled by the engine-manage-
ment ECU.
Exhaust brake
The injection of fuel into the engine is cut
off when the exhaust brake is switched on,
and intake air which is drawn into the cylin-
der is forced out again without having
mixed with fuel. An electropneumatic valve
operates a rotary valve or a flap in the ex-
haust pipe which serves as an obstacle to the
intake air attempting to leave the engine
through the exhaust pipe. The resulting air
cushion generated in the cylinder brakes the
piston in the compression and exhaust
strokes. With the exhaust brake, there is no
means of varying the degree of braking in-
tensity.
Auxiliary engine brake
When the engine is to be braked, an electro-
hydraulic valve-lifting device opens the ex-
haust valve at the end of the compression
stroke. The compression pressure collapses
as a result and energy is removed from the
system. Lube oil is used as the hydraulic
switching medium.
Retarder
The retarder is an auxiliary braking system
which is completely independent of the en-
gine. It is installed in the drivetrain down-
stream of the gearbox and is thus also effec-
tive when passing through neutral during
gear changes. There are two different sys-
tems:
Hydrodynamic retarder
Comprises a rotatable turbine wheel (brake
rotor) and at the opposite end a fixed tur-
bine wheel (brake stator). The rotor is me-
chanically connected to the vehicle drive.
When the brakes are applied, the blade
chambers in the stator and rotor fill with oil.
This oil is accelerated by the (rotating) rotor
and decelerated by the (fixed) stator. In the
process, the kinetic energy is converted to
heat and dissipated to the engine coolant.
The quantities of oil entering the rotor and
stator chambers can be used for infinite
variation of the braking effect.
Electrodynamic retarder
This comprises an air-cooled soft-iron disk
which rotates in a controllable electromag-
netic field generated by the vehicle battery.
The resulting eddy currents brake the disk,
and with it the vehicle wheels. The braking
effect is infinitely variable.
Engine-fan control
As a function of coolant temperature, the
engine ECU switches the engine's fan on
and off as required using an electromagnetic
clutch.
Electrically powered fans are being used
increasingly. Since they are not driven by the
engine V-belt, this permits innovative solu-
tions regarding their location in the engine
compartment.
Actuators Continuous-operation braking systems 89
Robert Bosch GmbH
Start-assist systems
Compared to gasoline, diesel fuel is far more
easily ignited. This is why the warm diesel
engine starts immediately when cranked.
The DI (direct injection) diesel engine even
starts immediately at temperatures down to
0 C. When starting, the 250 C auto-ignition
temperature is reached when the engine is
cranked at its starting speed. Prechamber en-
gines (IDI indirect injection) engines need
some form of start-assist system when start-
ing cold. DI engines on the other hand only
need assistance when starting below 0 C.
The cylinders of prechamber and swirl-
chamber engines are equipped with a
sheathed-element glow plug (GSK) in their
auxiliary combustion chamber which func-
tions as a hot spot. On small DI engines
(up to 1 l/cylinder), this hot spot is located
on the combustion chambers periphery.
Large DI truck engines on the other hand
have the alternative of using air preheating in
the intake manifold (flame start), or special,
easily ignitable fuel (Start Pilot) which is
sprayed into the intake air. Today, sheathed-
element glow plugs are used practically with-
out exception in start-assist systems.
Intake-air pre-heating
Flame glow plug
The flame glow plug burns fuel in the intake
tract to heat the incoming air. Normally, the
injection systems supply pump delivers fuel
to the flame plug through a solenoid valve.
The flame plugs connection fitting is pro-
vided with a filter, and a metering device
which permits passage of precisely the right
amount of fuel appropriate to the particular
engine. This fuel then evaporates in an evap-
orator tube surrounding the tubular heating
element and mixes with the intake air. The
resulting mixture ignites on the 1000 C
heating element at the flame-plug tip. The
heating power is limited since the heater
flame must not consume more than a frac-
tion of the oxygen needed for subsequent
combustion in the engine cylinder.
Electrical heating
A number of heater elements in the air-intake
system are switched on and off by a relay.
Sheathed-element glow plug
The sheathed-element glow plugs (GSK)
glow element is so firmly pressed into the
glow-plug shell (Fig. 1, Pos. 3) that a gas-
tight seal is formed. The element is a metal
glow tube (4) which is resistant to both cor-
rosion and hot gases, and which contains a
heater (glow) element embedded in magne-
sium-oxide powder (6). This heater element
comprises two series-connected resistors:
the helical heating wire (7) in the glow-tube
tip, and the control filament (5). Whereas
the helical heating wire maintains virtually
90 Actuators Start-assist systems
Figure 1
1 Electrical connector
terminal
2 Insulating washer
3 Glow-plug shell
4 Glow tube
5 Control filament
6 Filling powder
7 Helical heating wire
8 Heater-element gas-
ket
9 Double gasket
10 Round nut
1 2 3 4 7
8 1 cm 9 10
6 5
Sheathed-element glow plug GSK2 1
U
M
S
0
6
8
5
-
2
Y
Robert Bosch GmbH
constant electrical resistance regardless of
temperature, the control filament is made of
material with a positive temperature coeffi-
cient (PTC). On newer-generation glow
plugs (GSK2), its resistance increases even
more rapidly with rising temperature than
was the case with the conventional S-RSK
glow plug. This means that the newer GSK2
glow plugs are characterized by reaching the
temperature needed for ignition far more
quickly (850 C in 4 s). They also feature a
lower steady-state temperature which means
that their temperature is limited to a non-
critical level. The result is that the GSK2
glow plug can remain on for up to 3 minutes
following engine start. This post-glow fea-
ture improves both the warm-up and run-
up phases with considerable improvements
in noise and exhaust-gas emissions.
Glow control unit
The glow control unit (GZS) uses a power
relay for triggering the glow plugs. It receives
its start pulse from the engine ECU via a
temperature sensor.
The glow control unit controls the glow
duration of the glow plugs, as well as having
safety and monitoring functions. Using their
diagnosis functions, more sophisticated
glow control units are also able to recognise
the failure of individual glow plugs and in-
form the driver accordingly. Multiple plugs
are used as the control inputs to the glow
control units.
Functional sequence
The diesel engines glow plug and starter
switch, which controls the preheat and start-
ing sequence, functions in a similar manner
to the ignition and starting switch on the
gasoline engine. Switching to the ignition
on position starts the preheating process
(Fig. 3). When the glow-indicator lamp ex-
tinguishes, this indicates that the glow plugs
are hot enough for the engine to start, and
cranking can begin. In the following starting
phase, the droplets of injected fuel ignite in
the hot compressed air. The heat released as
a result leads to the initiation of the com-
bustion process.
In the warm-up phase following a suc-
cessful start, post-glow contributes to fault-
less engine running (no misfiring) and
therefore to practically smokeless engine
run-up and idle. At the same time, when the
engine is cold, pre-heating reduces combus-
tion noise. A glow-plug safety switchoff pre-
vents battery discharge in case the engine
cannot be started.
The glow control unit can be coupled to
the ECU of the Electronic Diesel Control
(EDC) so that information available in the
EDC control unit can be applied for opti-
mum control of the glow plugs in accor-
dance with the particular operating condi-
tions. This is yet another possibility for re-
ducing the levels of blue smoke and noise.
Actuators Start-assist systems 91
Figure 3
1 Glow-plug and
starter switch
2 Starter
3 Indicator lamp
4 To battery
5 Glow plugs
6 Self-sustained en-
gine operation
t
V
Preheating time
t
S
Ready to start
t
N
Postheating time
Figure 2
1 Sheathed-element
glow plug
2 Glow control unit
3 Glow-plug and
starter switch
4 To battery
5 Indicator lamp
6 Control line to the
engine ECU
7 Diagnosis line
t
V
t
S
t
N
1
2
3
4
5
6 Time t
Typical preheating sequence 3
U
M
S
0
6
6
7
-
2
E
1
3 2
4
6 7
5
EDC-controlled glow system in a direct-injection
(DI) diesel engine
2
U
M
S
0
6
9
1
-
2
Y
Robert Bosch GmbH
Technical term
A
Accelerator-pedal sensor, 32, 33
Accumulator injection system
p Common Rail System (CRS)
Active surge damping control, 52
Actuator diagnosis, 80
Air-mass meter, 34, 35
Altitude compensation, 53
Analog input signals, 38
Angle-of-rotation sensor (ARS)
(distributor pumps), 27
Arbitration (CAN-Bus), 84
ASIC (ECU), 41
Auxiliary coolant heating, 73
B
BIP control, 56
Blower (or fan) triggering, 74, 89
Boost-pressure control, 74, 88
Boot-shaped injection characteristic
(Unit Pump System), 72
Broad-band Lambda oxygen sensor, 36
C
Cascade control
(Lambda closed-loop control), 59
Characteristic data for injection
systems (Overview), 5
Closed-loop control, 44
Closed-loop start-of-delivery control
(IWZ signal), 7
Common Rail System (CRS),
, EDC triggering, 68f
, EDC overview, 17
, Principle of functioning, 10
Continuous-operation braking
systems, 89
Controller Area Network (CAN), 82f
Cruise control
p Vehicle-speed control 49
Cylinder shutoff, 53
Cylinder-balance control, 52
D
Data exchange with other
systems, 46, 47, 82f
Data processing (ECU), 38f
Diagnosis interface, 80
Diagnosis, 78f
Digital input signals, 39
Distributor injection pumps,
, EDC overview, 15, 16
, EDC triggering (actuators), 64, 65
, EDC triggering (high-pressure
solenoid valve), 66, 67
, EDC principle of functioning, 7, 8
Drive Recorder, 63
E
Electronic control unit (ECU), 38f
ECU link-up
, Unit injector system, 72
EGR
, Lambda-based closed-loop
control, 58
Electronic Diesel Control (EDC),
, Functional overview, 45, 48
, Functions, 44f
, Overview, 12f
End-of-Line (EoL) programming, 42
Engine (exhaust) brake, 89
Engine test bench, 62
Engine-brake function, 53
EPROM, EEPROM, 41
Exhaust-gas recirculation
(EGR), 74, 88
F
Flame glow plugs, 90
Flash-EPROM, 41
Fuel-quantity mean-value adaptation
, Operating mode: Direct and
indirect control, 60
Full-load smoke limitation
G
Glow control unit, 91
H
Half-differential short-circuiting-ring
sensor
(Rack-travel sensor), 30
Hot-film air-mass meter, 34, 35
92 Index of technical terms
Index of Technical Terms
An arrow p indicates a
term in italics
(e.g. p Common Rail
System) which is a syn-
onym or related term.
Robert Bosch GmbH
I
Identifier (CAN addressing), 84
Idle-speed control, 50
Incremental angle/time (IWZ)
signal, 55
Incremental angle-of-rotation sensor
(ARS) (Distributor injection
pump), 27
Injected-fuel-quantity limit, 53
In-line fuel-injection pumps
, EDC triggering, 63, 64
, EDC overview, 14f
, EDC principle of functioning, 6
Intake-air pre-heating, 90
Intake-duct switch-off, 73
Intake-manifold flap, 88
Intermediate-speed control, 51
L
Lambda closed-loop control, 57f
Lambda oxygen sensor, 36
p Broad-band Lambda oxygen
sensor, 36
M
Main Injection (MI), 68
Max. rpm control, 50
Memory (ECU), 40, 41
Message format (CAN), 85, 86
N
Needle-motion sensor, 31
O
On-Board-Diagnosis (OBD), 81
Open-loop control, 44
Oxygen pump cell
p Broad-band Lambda oxygen
sensor, 36
P
Parameters (engine), 75
Phase sensor (camshaft), 28, 29
Port-and-helix controlled injection
systems
p Distributor injection pumps
p In-line injection pumps
Post injection (POI), 68
Pre-glow, 90, 91
Pulse-shaped input signals, 39
Pulse-width-modulated (pwm)
signal, 42
R
Rack-travel sensor, 30
RAM, 41
Real-time compatibility, 43
Recharge, 69
Retarder, 89
ROM, 40
S
Sensors, 20f
, Accelerator-pedal, 32, 33
, Angle-of-rotation, 27
, Half-differential short-circuiting-
ring, 30
, Lambda oxygen, 36, 37
, Needle-motion, 31
, Phase (camshaft), 28, 29
, Pressure, 22f
, Rotational-speed, 26
, Temperature, 21
Sheathed-element glow plug, 90, 91
Single-plunger fuel-injection pumps
(Principle of functioning), 8
Smooth-running control (SRC), 52
Solenoid-valve-controlled injection
systems
p Common Rail System (CRS)
p Unit Pump System (UPS)
p Unit Injector System (UIS)
(Needle-motion sensor), 54
Start-assist systems, 90, 91
Start quantity, 50
Substitute functions/Equivalent
functions, 74
Swirl controller, 88
T
Throttle valve, 88
Torque control, 75f
Triggering (injection system), 63f
U
Unit Injector System (UIS),
, EDC overview, 18, 19
, Principle of functioning, 9,
Unit Pump System (UPS),
, EDC overview, 19
, Principle of functioning, 9
V
Vehicle-speed control
(cruise control), 51
Vehicle-speed limitation, 51
W
Wastegate
p Boost-pressure control, 81, 88
Index of technical terms 93
Robert Bosch GmbH
Abbreviations
A
ABS: Antilock Braking System
ACC: Adaptive Cruise Control
A/D: Analog/Digital
ADF: Atmospheric-pressure sensor
AGR: p Exhaust-gas recirculation
(EGR)
ARD: p Active surge-damping control
ARF: p Exhaust-gas recirculation
(EGR)
ARS: Angle-of-rotation sensor
p Accelerator-pedal sensor
ASIC: Application Specific Integrated
Circuit
ASR: Traction Control System (TCS)
AZG: Adaptive cylinder balancing
B
BIP signal: Signal for Beginning of the
Injection Period (also known as
Begin of Injection Period)
p (BIP control)
C
CAN: p Controller Area Network
CO: Carbon monoxide
CO
2
: Carbon dioxide
CR System: p Common Rail System
D
DI: Direct Injection
DZG: Rotational-speed sensor
(p Sensors)
E
EAB: p ELAB
ECE: Economic Commission for
Europe
EDC: Electronic Control Unit
(p Electronic Diesel Control)
EG: European Union
ELAB: Electrical shutoff valve
(In-line and distributor pumps)
EMV: Electromagnetic compatibility
(EMC)
EOBD: European p On-Board
Diagnosis
EOL programming:
p End-of-Line programming
ESP: Electronic Stability Program
EU: European Union
F
FGB: p Vehicle-speed limitation
FGR: p Vehicle-speed control
(Cruise Control)
G
GSK: p Sheathed-element glow plug
GZS: p Glow control unit
H
HC: Generic term for hydrocarbons
HDK: Half-differential short-circuiting-
ring sensor p Sensors
HE: Main Injection p MI
HFM: (p Hot-film air-mass meter)
HGB: (p Vehicle-speed limitation)
I
IDI: Indirect Injection
(Prechamber engines)
ISO: International Organization for
Standardization
IWZ-Signal: p Incremental angle/time
signal
K
KW: Crankshaft (cks)
L
LDR: p Boost-pressure control
LLR: p Idle-speed control
LRR: p Smooth-running control
M
MAB: Fuel shutoff
MAR: p Smooth Running Control
(SRC)
MI: p Main Injection
MIL: Malfuction Indicator Lamp
(diagnosis lamp)
MMA: p Fuel-quantity mean-value
adaptation (Lambda closed-loop
control)
MNEFZ: Modified new European
driving cycle (exhaust-gas test)
MSG: Engine ECU
MV: Solenoid valve
94 Index of technical terms Abbreviations
Robert Bosch GmbH
N
NBF: Needle-motion sensor
p Sensors
NBS: p Needle-motion sensor
NE: p Post injection p POI
NO
X
: Generic term for oxides of
nitrogen
NTC: Negative Temperature
Coefficient
NW: Camshaft (cms)
O
O
2
: Oxygen
OBD: p On-Board Diagnosis
OT: Top Dead Center (TDC)
P
PDE: p Unit Injector System
PE pump: p In-line fuel-injection
pumps
PF pump: p Single-plunger fuel-
injection pumps
PI: Pilot Injection
PLD: p Unit Pump system (UPS)
POI: Post Injection
PSG: Pump ECU
PTC: Positive Temperature Coefficient
PWG: Accelerator-pedal sensor
p Sensors
PWM signal: p Pulse-width-
modulated (pwm) signal
R
RWG: p Rack-travel sensor
S
SAE: Society of Automotive Engineers
SRC: p Smooth Running Control
T
TCS: p (ASR)
TD signal: Rotational-speed signal
TQ signal: Fuel-consumption signal
U
UIS: p Unit Injector System
UPS: p Unit Pump System
UT: Bottom Dead Center (BDC)
V
VE p Distributor injection
pump
VP30: Solenoid-valve-controlled axial-
piston p Distributor injection
pump
VP44: Radial-piston pump
p Distributor injection pump
VR pump: Radial-piston-
p Distributor injection pump
VTG: Turbocharger with Variable
Turbine Geometry
Z
ZDR: p Intermediate-speed control
Index of technical terms Abbreviations 95
Robert Bosch GmbH

Electronic Diesel Control EDC 2001

Uploaded by

Copyright:

Available Formats

Electronic Diesel Control EDC 2001

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronic Diesel Control EDC 2001

Uploaded by

Copyright:

Available Formats

ISBN-3-934584-47-0 The Bosch Yellow Jackets Edition 2001 Technical Instruction Diesel-Engine Management Order Number 1987722135 AA/PDI-08.

Hall element (Hall-effect vane switch) 1

Hall-effect angle-of-rotation sensor ARS1

Lambda control loop Further sensor signals

Air-mass control loop

from Bosch is the answer to

You might also like