List 1
List 1
List 1
manufacture of rolled steel plate, strip, sections and bars in accordance with the
requirements of LR's Rules and Regulations for the Classification of Ships Part 2, Chapter 3.
The information listed for each works is a summary of the product, generic grade and
maximum thickness, or in the case of round bars, diameter approved.
It is important to note that this List does not provide full details of the grades approved by
LR as required by the Rules. The combinations of deoxidation practice ( e.g. killed,
semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,
etc.), in association with specific rolling procedures
( e.g. N or TM, etc.), are not included. These parameters may vary within each grade by
manufacturer and could influence the fabrication procedures that can be applied.
Where required this information should be obtained from the current certificate of approval
issued to the manufacturer by LR.
Works designated ( Q.A. Approved ) are also approved under the Quality Scheme for
Materials in accordance with LR's Rules and Regulations for the Classification of Ships
Part 2, Chapter 1 Section 2.
The list also includes firms approved for the manufacture of fabricated steel sections and
steel by powder metallurgy.
Approval only covers the manufacturing location listed, it does not extend to other works
owned by the same company.
The local LR surveying office is also listed.
Abbreviations
B.O.S. Basic Oxygen Steelmaking
Con Cast Continuous Casting
E.A.F. Electric Arc Furnace
O.H. Open Hearth
NOTICE AND TERMS OF USE
Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees or
agents are, individually and collectively, referred to in this clause as the 'Lloyd's Register
Group'. The Lloyd's Register Group assumes no responsibility and shall not be liable to any
person for any loss, damage or expense caused by reliance on the information or advice in
this document or howsoever provided, unless that person has signed a contract with the
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
As at 19 March 2007
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Australia
As below B.O.S. / Con Cast Steelmaking BLUESCOPE STEEL (AIS) PTY. LTD. Sydney
A, B, D, E 50 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
A, B, D, E 13 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
6 Higher Strength
P.O. Box 1854
Wollongong
Port Kembla Steelworks
Tel: +61 2 42754666 Fax: +61 2 42753045 Email: mailto:nigel.attwell@bluescopesteel.com
Plates with specified through thickness properties notation Z35 may be added
NSW 2500
Austria
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
E.A.F./Ingot/Con Cast Steelmaking BREITENFELD EDELSTAHL AG Vienna
A-8662 Mitterdorf im Mrztal
Breitenfeldstrasse 22
Including VD/VOD
Tel: +43 (0)3858 6161 DW 279 Email mailto:stahl.vk@breitenfeld.at http://www.breitenfeld.at
As below E.A.F./Ingot/Con Cast Steelmaking BHLER EDELSTAHL GmbH Vienna
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
220 Structural Bars
Postfach 96
A-8605 Kapfenberg
Mariazellerstrae 25
Tel: +43 3862 20-0 7063 Fax: +43 3862 20 7559 Email: mailto:walter.wolflehner@bohler-edelstahl.at Web:http://www.bohler-edelstahl.at
A, B, D, E 20 Normal Strength Sections BHLER YBBSTAL PROFIL GmbH Vienna
AH32, AH36, DH32, DH36, EH32, EH36 20 Higher Strength
A, B, D, E 20 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32, EH36 20 Higher Strength
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless
20 Structural
Waidhofnerstrae 8
3333 Bhlerwerk
Tel: +43 7448 7007-24601 Fax: +43 7448 7007-24250 Email: mailto:harald.holzinger@bohler-profil.com Web:http://www.bohler-profil.com
High alloy bars and sections may be accepted for approved applications.
carbon, carbon-manganese, alloy, austenitic
stainless, duplex
38 Ingots ESR SONDERSTAHLWERK BREITENFELD GmbH Vienna
A-8661 Wartberg
Breitenfeldgasse 23
Including remelting of Ni materials
Tel +43 (0)3858 6161 279 Fax +43 (0)3858 6161 520 Email stahl.vk@breitenfeld.at Web http://www.breitenfeld.at
A 120 Normal Strength Bars STAHL JUDENBURG GmbH Vienna
carbon, carbon-manganese 120 Structural
carbon, carbon-manganese, carbon-manganese 120 Machinery
Gustahlwerkstrasse 21
A-8750 Judenburg
Tel: +43 3572 701-358 Fax: +43 3572 701-248 Email: mailto:christian.sunnitsch@stj.at Web: http://www.stahl-judenburg.com
As below B.O.S. / Con Cast Steelmaking VOESTALPINE GROBBLECH GmbH Vienna
A, B, D, E 140 Normal Strength Plates
AH32, AH36, DH32, DH36, EH32, EH36, FH32,
FH36
140 Higher Strength
360AR 40 Boiler & Pressure Vessel
410AR 50
360FG, 410FG, 460FG, 490FG, 510FG 140
1.5Ni, 3.5Ni, 5Ni, 9Ni 50 Ferritic Low Temperature
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36
140
D/304L 50 Clad
P.O. Box 3
Voest-Alpine Str.3
Tel: +43 732 6585 9091 Fax: +43 732 6980 9091 Email: mailto:ronald.lachmair@voestalpine.com
A-4031 Linz
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking voestalpine STAHL DONAWITZ GmbH & Co KG Vienna
carbon, carbon-manganese, alloy 285 Blooms/Billets Semi-Finished
A 8700 Leoben
Kerpelystrae 199
Tel: +43 3842 201 4322 Fax: +43 3842 201 2464 Email: mailto:wilfried.koelbl@voestalpine.com Web:http://www.voestalpine.com/stahldonawitz
As at 19 March 2007 2 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Belgium
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking CARSID S.A. Antwerp
carbon, carbon-manganese 310 Slabs Semi-Finished
42, 6100
Marcinelle
a member of the DUFERCO group
Rue de Marchienne
Email mailto:patrick.kick@carsid.com
As below B.O.S. / Con Cast Steelmaking Cockerill Sambre S.A. Antwerp
A, B 15 Normal Strength Plates
Ponte de Wandre
B-4683 Vivegnis
Groupe Arcelor
Site of Chertal
Tel +32 4 236 4180 Fax +32 4 236 4392 Email mailto:jean-francois-dewandre@arcelor.com
As below B.O.S. / Con Cast Steelmaking DUFERCO CLABECQ S.A. Antwerp
A, B, D, E 120 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
120 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
360, 410 50
360FG, 410FG, 460FG, 490FG, 510FG 120
Rue de Clabecq, 101
B-1460 Ittre
Tel: +32 (0) 2 3919227 Fax: +32 (0)2 3919883 Email:j.vermeulen@duferco.be Web:http://www.duferco.be
MQS Approved - Approval No. MQS016
As below E.A.F./Ingot/Con Cast Steelmaking INDUSTEEL BELGIUM Antwerp
A, B, D, E 50 Normal Strength Plates
AH32, AH36, DH32, DH36, EH32, EH36, EH40 50 Higher Strength
DH42, DH46, DH50, DH55, DH62, DH69, EH42,
EH46, EH50, EH55, EH62, EH69, FH42, FH46,
FH50, FH55, FH62, FH69
100
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, 5Ni
50 Ferritic Low Temperature
304L, 304LN, 316L, 316LN 50 Austenitic Stainless
UNS S31803(MOD)* 40 Duplex Stainless
266, Rue de Chtelet
B 6030 Charleroi
Tel: +32 71 44 17 86 Fax: +32 71 44 19 29 Email: mailto:eric.hologne@industeel.be Web: http://www.industeel.info
* accepted for approved applications
Quenched and tempered grades with specified through thickness properties
A 10 Normal Strength Sections LAMINOIRS DU RUAU S.A. Antwerp
A 25 Normal Strength Bars
Route De Trazegnies 147
B-6031 - Monceau Sur Sambre
Tel +33 (0)3-27142071 Fax +33 (0)3-27515095 Email: mailto:g.philippe@lme.fr
Bosnia & Herzegovina
As below E.A.F. / Ingot Steelmaking MITTAL STEEL ZENICA d.o.o. Split
A 50 Normal Strength Sections
A 50 Normal Strength Bars
72000 Zenica
Tel: +387 32467 032 Fax: +38732 467 035 Email: mailto:sulejman.muhamedagic@mittalsteel.com Web http://www.mittalsteelzenica
As at 19 March 2007 3 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Brazil
As below E.A.F./Ingot/Con Cast Steelmaking AOS VILLARES S/A -SIDENOR So Paulo
U1, U2, U3, R3, R3S, R4 125 Chain Cable Stock Bars
carbon, carbon-manganese 125 Machinery
Rod.Luiz Dumont Villares km 2- Moreira Csar
CEP 12.420-000
Pindamonhagaba Plant
Tel: +55 12 2126 7365 Fax: +55 12 2126 7325 EMail: mailto:marcelo.fazenda@villares.com.br Web:http://www.acosvillares.com.br
Pindamonhangaba S.P.
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking CST - COMPANHIA SIDERRGICA DE TUBARO Rio de Janeiro
A, B, D 16 Normal Strength Strip
360FG, 410FG 16 Boiler & Pressure Vessel
930 - Jardim Limoeiro
29164-970 Serra/ES
Av. Brigadeiro Eduardo Gomes
Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
Tel: +55 27 3348 2026 Fax: +55 27 3348 2211 Email : mailto:ciceroms@tubarao.com.br Web: http://www.cst.com.br
As below B.O.S. / Con Cast Steelmaking Cia. Siderrgica Paulista "COSIPA" So Paulo
A, B, D, E 80 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
80 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
Estrada de Piaaguera. Km 06
Cubato(SP)
Tel: +55 11 5070-8918 Fax: +55 11 5070-8925 Email: mailto:favali@cosipa.com.br Web:http://www.cosipa.com.br
Specified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.
CEP 11573-900
carbon, carbon-manganese, alloy B.O.S. / Ingot Steelmaking GERDAU AOMINAS S.A. Rio de Janeiro
Rodovia MG-443 KM 7
Fazenda do Cadete
Tel: +55 313 749-3122 Fax: +55 313 749-3215 Email: mailto:fernando.costa@gerdau.com.br web http://www.gerdau.com.br
Slabs and blooms intended for plates and forgings
36420-000-Ouro Branco-MG
As below E.A.F./Ingot/Con Cast Steelmaking Gerdau S/A Aos Finos Piratini Paranagua
A, B, D, E 58 Normal Strength Bars
360AR, 410AR 40 Boiler & Pressure Vessels
carbon, carbon-manganese, alloy 125 Structural
U1, U2, U3, R3, R3S, R4, API-2F 125 Chain Cable Stock
Avienda Getlio Vargas, 3200
96745-000 Charqueadas
Rio Grande do Sul
Tel: +55 51 3323 5669 Fax: +55 51 3323 5708 Email: mailto:afp@gerdau.com.br Web:http://www.gerdau.com.br
Rio Grande do Sul
As below B.O.S. / Con Cast Steelmaking USIMINAS Rio de Janeiro
A, B, D, E 50 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
A 12 Normal Strength Strip
360, 410 12 Boiler & Pressure Vessel
Av. Pedro Linhares Gomes, 5431
Distrito Usiminas, CEP 35160-900
Usinas Siderrgicas de Minas Gerais S/A
Usina Intendente Cmera
Tel +55 (0)31 38293136 Fax +55 (0)31 38293516 Email: mailto:ssampaio@usiminas.com.br
Q.A. Approved - Approval No. QA014
Ipatinga, Minas Gerais
As at 19 March 2007 4 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Bulgaria
As Below B.O.S./E.A.F./Ingot Steelmaking KREMIKOVTZI GROP Sofia
A 12 Normal Strength Plates
360AR, 410AR 12 Boiler & Pressure Vessel
A 12 Normal Strength Strip
360, 410 12 Boiler & Pressure Vessel
Sofia
Fax +35 976 670258
As below E.A.F. / Con Cast Steelmaking STOMANA INDUSTRY AD Sofia
As below 200 Blooms/Billets Semi-Finished
A 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 40
1, Vladaisko Vastanie Str.
2304 Pernik
Tel: +359 76 681 111 Fax: +359 76 670 258 Contact: Joanis Kokoupolous Web: http://www.stomana.bg
Canada
As below B.O.S. / Con Cast Steelmaking Algoma Steel Incorporated Toronto
D, E 50 Normal Strength Plates
A, B 60
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
Sault Ste. Marie
Ontario
P. O. Box 140
Tel +1 905 331 3455 Fax +1 905 331 3452 E-mail: mailto:rdionisi@algoma.com Web:http://www.algoma.com
P6A 5P2
As below E.A.F. / Con Cast Steelmaking GERDAU AMERISTEEL CORPORATION Toronto
A 26 Normal Strength Sections
Cambridge
Cambridge Division
160 Orion Place
Tel: +1 519 740 2488 ext 1420 Fax: +1 519 623 2062 Email: mailto:ehannah@gerdauameristeel.com
N1T 1R9
As below E.A.F. / Con Cast Steelmaking GERDAU AMERISTEEL WHITBY Toronto
A, B 15 Normal Strength Sections
AH27S, AH32, AH36 15 Higher Strength
Whitby
Ontario L1N 5T1
Hopkin Street South
CSA grades 260W, 300W and 350W may be accepted for approved applications as equivalent to the appropriate Lloyd's Register grade stated above.
Tel: +1 905 668 8811 ext 2744 Fax: +1 905 668 5356 Email: mailto:rgriffith@gerdauamericsteel.com Web: http://www.gerdauameristeel.com
China, People's Republic of
As below B.O.S. / Con Cast Steelmaking ANGANG STEEL COMPANY LIMITED Dalian
A, B, D, E 100 Normal Strength Plates
AH42, AH46, AH50, AH55, DH42, DH46, DH50,
DH55, EH42, EH46, EH50, EH55, FH42, FH46,
FH50, FH55
80 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
DH40, EH27S, EH32, EH36, EH40, FH27S, FH32,
FH36, FH40
100
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
Tiedong District
Anshan City,
HEAVY PLATE MILL
No. 396, South Zhonghua Road
All grades and thicknesses with specified through thickness properties, Z25 and Z35 designations.
Tel: +86 412 6334292 /6734881 Fax: +86 412 6722093 Email mailto: Web http://www.ansc.com.cn
Liaoning Province
As at 19 March 2007 5 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking ANGANG STEEL COMPANY LIMITED Dalian
A, B, D 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
360AR, 410AR 20 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 40
Anshan City
Liaoning Province
MEDIUM PLATE MILL
Angang Area
Tel +86 412 6723985 Fax +86 412 6724738
As below B.O.S. / Con Cast Steelmaking ANGANG STEEL COMPANY LIMITED Dalian
A, B, D 20 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 20 Boiler & Pressure Vessel
2150 HOT ROLLED STRIP PLANT
Tiexi District
Tel: +86 412 6334292/6734881 Fax: +86 412 6722093 Web http://www.ansteel.com.cn
As Below B.O.S./E.A.F./Con Cast Steelmaking ANYANG IRON & STEEL CO., LTD. Wuhan
E 25 Normal Strength Plates
A, B, D 36
EH27S, EH32, EH36 25 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36 36
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,
510FG
36 Boiler & Pressure Vessel
Anyang City
Henan Province
Yindu District
Tel: +86 372 3124036 Fax: +86 372 3121403
As below B.O.S. / Con Cast Steelmaking BAOSHAN IRON & STEEL CO., LTD. Shanghai Port
A, B, D, E 80 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
80 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 80 Boiler & Pressure Vessel
A, B, D 22 Normal Strength Strip
AH32, AH36 12 Higher Strength
460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
360FG, 410FG 22
Guoyuan, Fujin Road
Baoshan District
Baosteel Branch
Tel +86 21 2664 8888 Fax +86 21 2664 8000 Web:http://www.baosteel.com
Including all plate grades and thicknesses with specified through thickness properties (Z35)
Shanghai 200941
carbon, carbon-manganese, austenitic stainless E.A.F. / Ingot Steelmaking BAOSHAN IRON & STEEL CO., LTD. Shanghai Port
U1, U2, U3 130 Chain Cable Stock Bars
333 Tongji Road
Special Steel Branch Co.
Tel :+86 21 2603 2973/2603 2574 Fax: +86 21 2603 2162/2603 2276 Email mailto:ggc@No5Steel.com Web http://www.No5Steel.com
Shanghai 200940
As below B.O.S. / Con Cast Steelmaking BY STEEL Dalian
carbon, carbon-manganese 250 Slabs Semi-Finished
carbon, carbon-manganese 400 Blooms/Billets
BenXi City
LiaoNing Province
BEIYING IRON & STEEL (GROUP) CO., LTD.
BeiTai Town
Tel 0414 2529304/8667899 Fax: 0414 2529034 Email mailto:ybjbgs@126.com
117017
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking Benxi Iron & Steel (Group) Co. Ltd. Dalian
carbon, carbon-manganese 210 Slabs Semi-Finished
No. 16, Renmin Road
Liaoning Province
Benxi City
Tel: +86 414 7827417 Fax: +86 414 7827814
Email: mailto:jszxxcpc@bxsteel.com
Post Code: 117000
A, B, D 14 Normal Strength Sections CHANGSHU LONGTENG SPECIAL STEEL CO., LTD. Shanghai Port
Meili Town
Changshu City
No. 9 Jusha Road
Jiangsu Province 21551
As at 19 March 2007 6 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking CISCO Wuhan
As below O H / Ingot
A, B, D, E 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
360AR, 410AR, 460AR 32 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 40
A, B, D 15 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36 15 Higher Strength
U1, U2, U3 100 Chain Cable Stock Bars
Chongqing
Chongqing Iron and Steel Co., Ltd.
Dadukou
Tel: +86 23 6887 1279 Fax: +86 23 6887 1279 Email: mailto:bzcgjzc@public.cta.cq.cn
As Below B.O.S./E.A.F./Ingot Steelmaking Chengdu Sanyi Special Steel Co., Ltd. Wuhan
carbon, carbon-manganese, alloy 9 Ingots Semi-Finished
Pengzhou City
Sichuan Province
Sanyi
Tel: +86 28 83773044
P.C 611934
carbon, carbon-manganese E.A.F./Ingot/Con Cast Steelmaking DONGBEI SPECIAL STEEL GROUP Dalian
carbon, carbon-manganese 1380 Ingots Semi-Finished
carbon, carbon-manganese 240 Blooms/Billets
carbon, carbon-manganese 200 Structural Bars
U1, U2, U3 130 Chain Cable Stock
by continuous cast route 110 Machinery
carbon, carbon-manganese 200
Qiqihar City
Heilongjiang Province
BEIMEN SPECIAL STEEL CO., LTD.
Fularji District
Tel: +86 452 6801920 Fax: +86 452 6801496 Email: mailto:lhy999@163.net
As below E.A.F./Ingot/Con Cast Steelmaking Daye Special Steel Co. Ltd. Wuhan
carbon, carbon-manganese 190 Structural Bars
U1, U2, U3, API-2F 110 Chain Cable Stock
R4 160
carbon, carbon-manganese, alloy 190 Machinery
Huangshi City
Hubei Province
Tel: +86 714 6292301 Fax: +86 714 6293888
Post code: 435001
As below B.O.S. / Con Cast Steelmaking GUANGXI LIUZHOU Guangzhou
A, B 20 Normal Strength Plates
360AR, 410AR 20 Boiler & Pressure Vessel
117 Beique
Liuzhou
IRON & STEEL (GROUP) COMPANY
Tel: +86 (0)772 2592132 Fax: +86 (0)772 2592784 Email mailto:lggsb@public.gx.cn
Guangxi
As below B.O.S. / Con Cast Steelmaking HANDAN IRON & STEEL GROUP CO., LTD. Wuhan
As below Slabs Semi-Finished
As below Blooms/Billets
A, B, D 38 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
38 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 38
Handan City
Hebei province
232 Fuxing Road
Tel: +86 310 6072275 Fax: +86 310 6072815
056015
As below E.A.F. / Ingot Steelmaking Inner Mongolia North Heavy Industries Group
Company
Wuhan
carbon, carbon-manganese, alloy 8 Ingots Semi-Finished
Baotou City
Inner Mongolia
Changqian road
Including semi-finished blooms up to 8.5 tonnes in carbon, carbon-manganese and alloy steel
014033
As at 19 March 2007 7 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking JIANGSU HUAIGANG GROUP CO., LTD. Nanjing
As below E.A.F. / Con Cast
carbon, carbon-manganese 200 Blooms/Billets Semi-Finished
carbon, carbon-manganese 100 Structural Bars
U1, U2, U3 100 Chain Cable Stock
carbon, carbon-manganese 92 Machinery
Huai'an City
Jiangsu
No. 53 Huagong Road
Tel +81 0517 3802468 Fax +81 0517 3631344 PC 223002 Email mailto:hyhmic@public.hy.js.cn Web http://www.huagang.com
As below E.A.F. / Ingot Steelmaking JIANGSU XIGANG GROUP CO., LTD. Shanghai Port
U1, U2, U3 330 Chain Cable Stock Bars
carbon, carbon-manganese 330 Semi-finished Products
No. 124, Tangnan Road
Wuxi
Tel +86 510 5750440 Fax +86 510 5759085 Email: mailto:Wuxinet@public1.Wx.js.cn
Jiangsu
As below E.A.F. / Con Cast Steelmaking JIANGYIN XINGCHENG SPECIAL STEEL WORKS
CO., LTD.
Nanjing
carbon, carbon-manganese, alloy 130 Structural Bars
R3S, R4 110 Chain Cable Stock
U1, U2, U3 130
carbon, carbon-manganese, alloy 130 Machinery
297, Bin Jiang East Road
Jiangyin City
Tel: +86 510 6193388-6050 Fax: +86 510 6195042 Email: mailto:jyxctg@public1.wx.js.cn Web: http://www.jyxc.com
Jiangsu province 214429
As below B.O.S. / Con Cast Steelmaking JINAN IRON AND STEEL CO., LTD. Qingdao
A, B, D, E 50 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
Jinan, 250101
Shandong Province
21, Gongye Bei Road
All grades and thicknesses with specified through thickness properties, designation Z35 may be added
Tel +86 531 8869748 Fax +86 531 8982126 Email: jigang@jigang.com.cn Web:http://www.jigang.com.cn
A, B 12 Normal Strength Sections Jiangmen Xinhui Yili Section Steel Mill Co., Ltd. Guangzhou
Xinhui City
Guangdong Province
Xinhui Shuangshui Industry Development Zone
Tel: +86 750 6417718 Fax: +86 750 9417728
Post zip: 529153
As below B.O.S. / Con Cast Steelmaking Jiangsu Shagang Group Co., Ltd. Shanghai Port
carbon, carbon-manganese 220 Slabs Semi-Finished
carbon, carbon-manganese 220 Blooms/Billets
Jinfeng Town
Zhangjiagang City
Hogfa Steel Plant
Tel: +86 512 5856 8800 Fax: +86 512 5855 0818
Jiangsu Province 215625
As below B.O.S. / Con Cast Steelmaking Jiuquan Iron and Steel Group Co., Ltd. Dalian
A, B, D 30 Normal Strength Plates
Jiayuguan City
Gansu Province
12 Xunguan East Road
Tel: 0937 6715401 Fax: 0937 6713310 Email mailto:jizhiban@jiugang.com Web http://www.jiugang.com
735100
As Below B.O.S./E.A.F./Ingot Steelmaking LAIWU STEEL CO., LTD. Dalian
U1, U2, U3 130 Chain Cable Stock Bars
Gang Cheng District
Laiwu City
You Yi Street
Tel +86 634 6821211 Fax: +86 634 6820824
Shandong Province
As below E.A.F. / Ingot Steelmaking LAIWU STEEL GROUP Dalian
carbon, carbon-manganese, alloy 30 Ingots Semi-Finished
West end of Gangdu Str.
Gangcheng District
MACHINERY & MANUFACTURING CO., LTD.
Laiwu City
As at 19 March 2007 8 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Ingot Steelmaking LIAO NING FU-AN FOUNDRY CO., LTD. Dalian
carbon, carbon-manganese, alloy, austenitic
stainless
30 Ingots Semi-Finished
An Shan City
114016
No 8 An Zheng Road
Fax: 0412 8437606
Liao Ning Province
As below B.O.S. / Con Cast Steelmaking MAANSHAN IRON & STEEL COMPANY LIMITED Nanjing
A, B 25 Normal Strength Plates
AH32, AH36, DH32, DH36 25 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
No.8 Hongqi Road (N)
Maanshan City
Tel: +86 555 2886 904 Fax: +86 555 2886 904 Email: mailto:zbcjsk@mail.magang.com.cn
Anhui Province PC:243000
As below B.O.S. / Con Cast Steelmaking Minmetals Yingkou Medium Plate Co., Ltd. Dalian
A, B, D 30 Normal Strength Plates
360AR, 410AR 25 Boiler & Pressure Vessel
360FG, 410FG 30
Laobian District
Yingkou City
Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057 Email mailto:jszlb-wkyg@16.com
Liaoning Province
As below B.O.S. / Con Cast Steelmaking NISCO Nanjing
A, B, D 35 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36 35 Higher Strength
460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
360AR, 410AR, 360, 410 25
360FG, 410FG 35
U1, U2, U3 80 Chain Cable Stock Bars
XieJiaDian
Dachang District
Nanjing Works
Tel: +86 25 570 73774 Fax: +86 25 57793425 EMail mailto:zgc@njsteel.com.cn Web:http://www.nisco.com.cn
Nanjing, Post Code: 210035
A, B 15 Normal Strength Sections NISCO Nanjing
AH32, AH36 15 Higher Strength
Huazhuan Town
Binhu District, Wuxi City
Wuxi Jinxin Steel Rolling Co., Ltd.
Tel +86 510 5613100 Fax: +86 510 5601 450 Email: mailto:zxct@fm365.com
Jiangsu Province 214131
carbon, carbon-manganese, alloy, boiler &
pressure vessel grades
B.O.S. / Con Cast Steelmaking Pangang Group Chengdu Iron & Steel Co., Ltd. Wuhan
carbon, carbon-manganese, alloy 310 Billets Semi-Finished
Tuanjienanlu Street
Qingbaijiang District
Qingbaijiang Plant
Tel: (028) 84407668 Fax: (028) 84503981
Chengdu
As below B.O.S. / Con Cast Steelmaking Panzhihua New Steel & Vanadium Company Ltd Guangzhou
A, B 12 Normal Strength Strip
AH32, AH36 12 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
Panzhihua City
Sichuan Province
Tel +86 812 3394223 Fax +86 812 3391469 Email: mailto:zlc@pzhsteel.com.cn
617062
E 32 Normal Strength Plates QINHUANGDAO SHOUGANG PLATE MILL CO.,
LTD.
Dalian
A, B, D 35
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
32 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 32 Boiler & Pressure Vessel
360AR, 410AR 35
No. 409 Jianshe Street
Qinhuangdao City
Tel: +86 (0)335 3011421/3023 Fax: +86 (0)335 3014693
Hebei Province
As at 19 March 2007 9 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking Qinhuangdao Shouqin Metal Materials Co., Ltd Dalian
carbon, carbon-manganese 250 Slabs Semi-Finished
Funing County
Qinhuangdao
Duzhuang
Zip 066326 Tel +86 335 6089871 Fax +86 335 6089606 Web http://www.shouqin.com.cn
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength steels according to the Society's Rules
for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for ordering steel which complies with their
approved chemical composition and enables them to achieve the required mechanical properties
Hebi Province
As below B.O.S. / Con Cast Steelmaking SHANDONG SHOUGUANG JUNENG Qingdao
carbon, carbon-manganese 130 Structural Bars
U1, U2, U3 95 Chain Cable Stock
carbon, carbon-manganese 95 Machinery
Tegang Road 9
262711
SPECIAL STEEL Co., Ltd.
Shouguang Beiluo Industry Garden
Tel +86 536 5186777 Tel+86 536 5186789
Shandong Province
A, B, D, E 100 Normal Strength Plates SHANGHAI SANGANG STEEL Co., Ltd. Shanghai Port
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
80 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
460FG, 490FG, 510FG 80
360, 410, 360FG, 410FG 100
Pudong
Shanghai
300 Shangnan Road
Tel: +86 21 58839180 Ext 3244 Fax: +86 21 5886 2917
Specified through thickness properties on all plate grades up to 30 mm thickness.
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking SHAOGUAN IRON & STEEL (GROUP) CO., LTD. Guangzhou
A, B, D 36 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
36 Higher Strength
360AR, 410AR 20 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 36
Qujiang County
Shaoguan City
Maba
Tel: +86 (0)751 8784492 Fax: +86 751 8786066
Guangdong 512123
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking SHIJIAZHUANG I & S CO., LTD. Dalian
carbon, carbon-manganese 150 Structural Bars
U1, U2, U3 150 Chain Cable Stock
carbon, carbon-manganese 150 Machinery
Shijiazhuang
Hebei
No. 363 Heping E Road
Tel: +86 (0)311 869131413 Fax: +86 (0)311 86913368
As below B.O.S. / Con Cast Steelmaking SHOUGANG CORPORATION Dalian
A, B, D 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 40
Beijing
Shijingshan District
Tel +86 (0)10 68873676 Fax: +86 (0)10 68873345
As below E.A.F./A.O.D./Con Cast Steelmaking STAINLESS STEEL INCORPORATED COMPANY
LTD. OF TISCO
Dalian
304L, 316L 20 Austenitic Stainless Plates
UNS S31803 20 Duplex Stainless
Jaincaoping Street No. 2
Taiyuan
030003
Taiyuan
SHANXI
As below E.A.F. / Ingot Steelmaking TIANJIN TIANZHONG JIANGTIAN SPECIAL STEEL
CO., LTD.
Dalian
carbon, carbon-manganese, alloy 43 Ingots Semi-Finished
As at 19 March 2007 10 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Beichen District
Tianjin City 300400
Tianzhong
Tel: +86 22 26611928 Fax: +86 22 26346483
As below B.O.S. / Ingot Steelmaking Taiyuan Iron & Steel ( Group) Co. Ltd. Dalian
carbon, carbon-manganese, alloy, austenitic
stainless steel
400 Blooms/Billets Semi-Finished
No. 2 Jian Cao Ping Street
Taiyuan
Tel +86 0351 3017686 Fax +86 0351 3017893 Email: mailto:lw0241@163.com Web: http://www.tisco.com
Shanxi Province
A, B 20 Normal Strength Plates Tianjin Tiandun Co., Ltd. Dalian
360AR, 410AR 20 Boiler & Pressure Vessel
No. 4 Biandian Suo Road
Second Bridge, Hedong District
Tel: +86 22 84211234-231 Fax: +86 22 84211219
Tianjin, 300180
A, B B.O.S. / Con Cast Steelmaking Tianjin Tiangang Steel (Group) Co., Ltd. Dalian
No. 1 Zhang Da Zhong Road
Hedong District
Tel +86 22 84262715 -389 Fax +86 22 84270758
Tianjin
As below B.O.S. / Con Cast Steelmaking WISCO Wuhan
A, B, D, E 50 Normal Strength Plates
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
A, B, D 25 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36 25 Higher Strength
360, 410 12 Boiler & Pressure Vessel
A, B 13 Normal Strength Sections
Qingshan
Wuhan
Wuhan Iron and Steel Co., Ltd.
Changqian
Tel: +86 27 86892086 Fax: +86 27 86892413
A, B 14 Normal Strength Sections WUXI XI'NAN STEEL ROLLING Co., Ltd. Shanghai Port
AH32, AH36 14 Higher Strength
Wuxi City
Jiangsu Province
North of Nan Quan Town
Tel: +86 510 85952258 Fax: +86 510 85952310
214128
As below E.A.F. / Con Cast Steelmaking WUXI XIXING IRON & STEEL Co., Ltd. Shanghai Port
A, B, AH27S, AH32, AH36 180 Blooms/Billets Semi-Finished
Qianqiao Town
Wuxi
64, Qian Wei Road
Tel: +81 (0)510 8321 5681 Fax: +81 (0)510 8321 5681
Jiangsu
As below E.A.F./Ingot/Con Cast Steelmaking WUYANG IRON & STEEL COMPANY LTD. Wuhan
A, B, D, E 150 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
Henan Province
P.N: 462500
Wugang City
Tel: +86 375 8111230 Fax: +86 3758114006
Plates with specified through thickness properties in listed grades of normal and higher strength steels.
A, B, D 18 Normal Strength Sections XINGTAI JITAI SPECIAL SHAPED STEEL WORKS Dalian
AH27S, AH32, AH36, DH27S, DH32, DH36 18 Higher Strength
Xingtai City
Hebei Province
No.668 Xinxing East Street
Tel +86 319 3033327 Fax +86 319 3033326
A, B, D 40 Normal Strength Plates XINYU IRON & STEEL Co. Ltd. Wuhan
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
360AR, 410AR 20 Boiler & Pressure Vessel
Xinyu City
Jiangxi Province 338001
1 Yejin Road
Tel: 0790 629 3426 Fax: 0790 629 4727 Email: xgzgc.pzk@163.com
All grades with specified through thickness properties, designation Z35 may be added
As at 19 March 2007 11 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking XISCO - HUNAN VALIN XIANGTAN Wuhan
A, B, D, E 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
410FG, 460FG, 490FG 25 Boiler & Pressure Vessel
360FG 40
Xiangtan
Hunan
IRON & STEEL CO., LTD.
Yuetang District
Z35 designation may be added to all grades of plate
Tel +86 (0)732 8652953 Fax +86 (0) 732 8652954 Email mailto:xsb@mail.hnxg.com.cn Web http://www.hnxg.com.cn
Czech Republic
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking MITTAL STEEL OSTRAVA a.s. Prague
A, B, D 14 Normal Strength Sections
A, B, D 60 Normal Strength Bars
Vratimovsk 689
707 02 Ostrava-Kuncice
Tel: +420 59 568 3644 Fax: +420 59 568 2062 Email: mailto:skosmider@novahut.cz Web http://www.mittalsteelostrava.com/
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking SKODA, HUTE, Plzen, s.r.o. Prague
carbon, carbon-manganese, alloy Ingots Semi-Finished
Tylova 1/57
31600 Plzen
Member of the consorcium
SKODA STEEL
Tel: +420 378 132 265 Fax: +420 378 134 436 EMail: mailto:milena.krejcova@skoda.cz Web: http://www.skoda.cz
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking SKODA, KOVARNY, Plzen, s.r.o. Prague
carbon, carbon-manganese, alloy 200 Ingots Semi-Finished
Member of the consorcium
SKODA STEEL
Tel: +420 378 134 856 Fax: +420 378 134 888 EMail: mailto:karel.vovesny@skoda.cz Web: http://www.skoda.cz/steel
carbon, carbon-manganese, alloy 300 Structural Bars SOCHOROV VLCOVNA T, a.s. Prague
carbon, carbon-manganese, alloy 300 Machinery
272 01 Kladno
Drn
Machinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.
As below B.O.S./Ingot/Con Cast Steelmaking Trineck elezrny a.s. Prague
As below E.A.F./Ingot/Con Cast
A 50 Normal Strength Sections
U1, U2, R3 72 Chain Cable Stock Bars
carbon, carbon-manganese, alloy 90 Machinery
Prumyslova 1000
739 70 Trinec
Tel: +420 558 532 066 Fax: +420 558 532 451 Email: mailto:exports@moravia-steel.cz Web hppt://www.trz.cz
Stare Mesto
B, D 40 Normal Strength Sections Trineck elezrny a.s. Prague
A 50
DH32, DH36 40 Higher Strength
AH27S, AH32, AH36 50
735 93 Bohumn
Provoz VB - Univerzln Trat
Bezrucova 300
As below E.A.F. / Ingot Steelmaking VITKOVICE HEAVY MACHINERY, a.s Prague
carbon, carbon-manganese, alloy 80 Ingots Semi-Finished
Ruska 2887/101
706 02 Ostrava-Vitkovice
Tel: +420 595 955 322 Fax: +420 595 952 005 Email: mailto:zdenek.mikosek@vitkovice.cz Web: http://www.vitkovice.cz
As below B.O.S./Ingot/Con Cast Steelmaking VITKOVICE STEEL, a.s. Prague
As Below OH/Ingot/ Con Cast
A, B, D, E 100 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 100 Boiler & Pressure Vessel
A, B, D, E 16 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
16 Higher Strength
A, B, D, E 50 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36 50 Higher Strength
709 00 Ostrava - Hulvaky
Stramberska c.p. 2871/47
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Tel: +420 59 595 5842 Fax: +420 59 595 7340 Email: mailto:miroslav.snajdr@VitkoviceSteel.com Web: http://www.vitkovicesteel.com
As at 19 March 2007 12 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A O H / Ingot Steelmaking Zelezrny Hrdek, A.S. Prague
A 150 Normal Strength Bars
338 42 Hrdek
Nova Hut 204
Hrdek - Nov Hut
Tel: +420 181 765359 Fax: +420 181 726165 Email:mailto:ckahovec@seznam.cz
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking DAS, a.s. Prague
carbon, carbon-manganese, alloy 12 Ingots Semi-Finished
59171 dr nad Szavou
Metallurgical Plant
Tel: +420 566 643 998 Fax: +420 566 642 803 Email: mailto:antonin.tlusty@zdas.cz Web:http://www.zdas.cz
Denmark
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking DANSCAN STEEL A/S Copenhagen
carbon, carbon-manganese 200 Billets Semi-Finished
DK-3300
Frederiksvrk
Havnevej 47
Tel: +45 47 76 76 00 Fax: +45 47 76 7802 Email mailto:contact@barmill.dk
E 60 Normal Strength Plates DANSTEEL A/S Copenhagen
A, B, D 100
EH32, EH36, EH36S 80 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36 100
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
DK-3300 Frederiksvrk
Havnevej 33
Tel: +45 47770333 Fax: +45 47770302 Email: mailto:zib@dansteel.dk Web:http://www.dansteel.dk
Specified through thickness properties for all plate grades
A, B, D 40 Normal Strength Sections DUFERCO DANISH STEEL A/S Copenhagen
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
A, B, D 40 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
DK-3300
Frederiksvrk
Havnevej 47
Tel: +45 47 76 76 00 Fax: +46 47 76 7602 Email mailto:contact@barmill.dk
Egypt, Arab Republic of
As below B.O.S. / Con Cast Steelmaking EGYPTIAN IRON & STEEL CO. Port Said
A 50 Normal Strength Plates
A 50 Normal Strength Strip
360FG, 410FG 25 Boiler & Pressure Vessel
A 50 Normal Strength Sections
Helwan
Cairo
El Tebbin
Tel: +202 5011599 Fax +202 5011608 Email: mailto:eisc@idsc.gov.eg Telex 20176 Tebbin
Finland
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking Fundia Wire Oy Ab Helsinki/Helsin
gfors
FIN-10820 LAPPOHJA
Koverhar
Tel .+358 19 22 11 Fax +358 19 2214150 Email:mailto:tuomas.antola@fundia.fi
As below E.A.F. / Con Cast Steelmaking OUTOKUMPU STAINLESS OY Helsinki/Helsin
gfors
304L, 316L, 317L, 321, 347, UNS S31254, UNS
N08904
12 Austenitic Stainless Plates
304L, 316L, 317L, 321, 347, UNS S31275, UNS
N08904
12 Austenitic Stainless Strip
95400 Tornio
Tel: +358 16 4521 Fax: +358 16 452350 Email: mailto:timo.kauppila@outokumpu.com Web: http://www.outokumpu.com
As below E.A.F. / Con Cast Steelmaking OVAKO BAR Oy Ab Helsinki/Helsin
gfors
A, B, D, E 180 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
180 Higher Strength
carbon, carbon-manganese, alloy 180 Structural
As at 19 March 2007 13 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Finland
180 Structural Bars gfors
alloy 180 Machinery
carbon, carbon-manganese 200
Terstehtaantie 1
FI-55100 IMATRA
Tel: +358 5 68021 Fax: +358 5 6802553 Email: mailto:heikki.hurmola@ovako.com Web:http://www.ovako.com
MQS Approved - Approval No. MQS 020
Including bolts and studs manufactured at AA Fabricating Oy, Piikatu 16, 55120 Imatra, Finland.
A, B, D, E 13 Normal Strength Fabricated Sections RUUKKI Helsinki/Helsin
gfors
AH32, AH36, DH32, DH36, EH32, EH36 13 Higher Strength
Lehtolantie
Fin-92600 Pulkkila
Rautaruukki OYJ
Pulkkila Works
Tel: +358 05927034 Fax: +358 8 811 7090 Email: mailto:arto.tormalehto@ruukki.com Web:http://www.ruukki.com
As below B.O.S. / Con Cast Steelmaking RUUKKI Helsinki/Helsin
gfors
A, B, D, E 150 Normal Strength Plates
FH27S, FH32, FH36 40 Higher Strength
AH40, DH40, DH42, EH40, EH42 80
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
150
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,
510FG
100
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
40 Ferritic Low Temperature
A, B, D, E 15 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
15 Higher Strength
FIN 92101 Raahe
Rautaruukki Oyj
P.O. Box 93
Tel +358 20 5911 Fax + 358 20 59 23527 Email:mailto:lassi.myllykoski@rauraruukki.com Web: http://www.rautaruukki.com
Specified through thickness properties for up to 100 mm thickness.
MQS Approved - Approval No. MQS 007
France
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking ADA Bilbao
A, B, D, E, AH27S, AH32, AH36, DH27S, DH32,
DH36, EH27S, EH32, EH36
180 Blooms/Billets Semi-Finished
64340 Boucau
Acierie de L'Atlantique
Rond Point Claudius Magnin BP N 1
Tel +33 5 59 64 41 00 Fax +33 5 59 64 41 20
As below E.A.F./Ingot/Con Cast Steelmaking ASCOMETAL Dunkerque
carbon, carbon-manganese, alloy 400 Blooms/Billets Semi-Finished
carbon, carbon-manganese, alloy 310 Structural Bars
R4 78 Chain Cable Stock
U3 105
U1, U2 130
carbon, carbon-manganese, alloy 310 Machinery
59941 Dunkerque
Cedex 2
Usine de Dunes
BP 41
Machinery grades up to 180 mm by continuous casting, 310 mm by ingot
Tel +33 32829 6203 Fax +33 32829 6003
As at 19 March 2007 14 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Ingot Steelmaking ASCOMETAL Marseille
carbon, carbon-manganese, alloy 450 Blooms/Billets Semi-Finished
carbon, carbon-manganese, alloy 325 Structural Bars
13771 Fos-sur-Mer
Usine de Fos-sur-Mer
BP 30
Tel: (33) 442 479250 Fax: (33) 442 479014 Email : mailto:e.leroy@ascometal.lucchini.com
As below E.A.F. / Ingot Steelmaking AUBERT & DUVAL Lyon
carbon, carbon-manganese, alloy, austenitic
stainless steel
450 Blooms/Billets Semi-Finished
carbon, carbon-manganese, alloy, austenitic
stainless
50 Structural Bars
carbon, carbon-manganese, alloy, austenitic
stainless
200 Machinery
BP 1
63770 Les Ancizes
Aciries des Ancizes
Tel: +33 4 7367 0421 Fax: +33 4 7367 7939 Email: mailto:au-duval@nat.fr
Forged bars up to 400 mm thickness/diameter in all above grades
E 80 Normal Strength Plates G.T.S. Industries Dunkerque
A, B, D 100
AH40, DH40, EH40, FH40 42 Higher Strength
FH27S, FH32, FH36 50
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
75
460FG, 490FG, 510FG 50 Boiler & Pressure Vessel
360FG, 410FG 100
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
50 Ferritic Low Temperature
BP 6317
59379 Dunkerque Cedex 1
Dunkerque Mill
Tel: +33 (0)3 28 29 37 40 Fax: +33 (0)3 28 29 69 04
Specified through thickness properties for all nornal and higher strength grade plates.
As below E.A.F. / Ingot Steelmaking INDUSTEEL GROUPE ARCELOR Lyon
A, B, D, E 150 Normal Strength Plates
FH32, FH36 50 Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36 150
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100 Boiler & Pressure Vessel
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
50 Ferritic Low Temperature
304L, 316L 50 Austenitic Stainless
56 rue Clemenceau BP 56
71202 LE CREUSOT CEDEX
Tel: +33 3 8580 5721 Fax: +33 3 8580 5800 Email: mailto:gilbert.primon@industeel.arcelor.com Web: http://www.industeel.info
Plates with specified through thickness properties.
carbon, carbon-manganese E.A.F. / Ingot Steelmaking INDUSTEEL LOIRE Lyon
A 400 Normal Strength Plates
FH32, FH36 50 Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36 400
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,
9Ni
50 Ferritic Low Temperature
BP 368 - Chateauneuf
42803 RIVE DE GIER
ARCELOR Group
Site de Chateauneuf
Tel: +33 4 77 75 21 03 Fax: +33 4 77 75 20 03 Email: mailto:jacqueline-coste@industeel.arcelor.com
Plates with specified through thickness properties.
austenitic stainless E.A.F. / Ingot Steelmaking Imphy Alloys Lyon
Fe-36Ni* 8 Fe-Ni alloys Plates
Fe-36Ni* 8 Fe-Ni alloys Strip
304L, 316L 21 Austenitic Stainless Bars
austenitic stainless 300 Semi-finished Products
Avenue Jean Jaurs
58160 IMPHY
*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) for approved applications.
Tel: +33 3 86 21 34 24 Fax: +33 3 86 21 31 00 Email:mailto:pierre-roger.martin@iup.arcelor.com Web:http://www.imphyalloys.com
As at 19 March 2007 15 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
AH32, AH36 16 Higher Strength Sections LORRAINE TUBES GRUPO CONDESA Lyon
BP 9
57480 Sierk-les-bains
Lexy-France
Usine de RETTEL
Tel: +33 03 82 25 22 06 Fax: +33 03 82 25 22 06 Email:mailto:jlhensgen@lorraine.condesa.fr
Welded hollow sections
As below B.O.S. / Con Cast Steelmaking Lamines Marchands Europeens Lyon
A 13 Normal Strength Sections
A 30 Normal Strength Bars
2, Rue Emile Zola
BP 1
Tel +33 (0)3 2714 2010 Fax +33 (0)3 2714 2020 Email: mailto:g.philippe@lme.fr
59125 Trith-St-Lger
As below B.O.S. / Con Cast Steelmaking SOLLAC MEDITERRANEE Groupe ARCELOR Marseille
A, B, D 16 Normal Strength Strip
AH32, AH36, DH32, DH36, EH36S 13 Higher Strength
460FG, 490FG, 510FG 13 Boiler & Pressure Vessel
360FG, 410FG 16
Zone Industrielle
13776 Fos sur Mer Cedex
Usine de Fos-sur-Mer
Tel +33 (0)4 4247 2934 Fax +33 (0)4 4247 3231
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking SOLLAC ATLANTIQUE Dunkerque
BP 2508
59381 Dunkerque Cedex 1
Site de Dunkerque
Tel: +33 (0)3 28 29 31 43 Fax: +33 (0)3 28 29 64 04
As below E.A.F./A.O.D./Con Cast Steelmaking UGINE & ALZ - Arcelor Group Lyon
304L, 316L, 321 8 Austenitic Stainless Plates
71130 GUEUGNON
Gueugnon Plant - Post Box 1
Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Email: mailto:gerard.ramoissenet@ugine-alz.arcelor.com
As below E.A.F./A.O.D./Con Cast Steelmaking UGITECH S.A. Lyon
304L, 316L, 321 32 Austenitic Stainless Sections
UNS S31803 32 Duplex Stainless
304L, 316L, 321 130 Austenitic Stainless Bars
UNS S31803 130 Duplex Stainless
austenitic stainless, duplex stainless 95 Machinery
73403 UGINE Cedex
Tel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74 Email: mailto:laurent.prost@ugine.savoie.usinor.com Web: http://www.ugitech.com
Germany, Federal Republic of
As below B.O.S. / Con Cast Steelmaking ARCELOR BREMEN GmbH Bremen
A, B, D 20 Normal Strength Strip
360, 410, 360FG, 410FG 20 Boiler & Pressure Vessel
Postfach 21 02 20
D-28222 Bremen
Tel +49 421 648 2813 Fax +49 412 648 3150 Email: mailto:frank.witt@aecelor-bremen.com Web: http://www.arcelor-bremen.com
A, B, D, E, AH32, AH36, DH32, DH36, EH32,
EH36, carbon, carbon-manganese, boiler &
pressure vessel grades, 360, 410, 460, 490, 360FG,
410FG, 490FG, 510FG
B.O.S. / Con Cast Steelmaking ARCELOR EISENHTTENSTADT GMBH Dortmund
D-15872 Eisenhttenstadt
Werkstrae 1
Tel +49 3364 3782 05 Fax +49 3364 3781 97 Email: mailto:frank.schadow@arcelor.com Web http://www.eko-stahl.de
Continuously cast slab up to 250 mm thickness and cast bloom up to 300 mm thickness.
As below B.O.S./Ingot/Con Cast Steelmaking Aktiengesellschaft der Dillinger Httenwerke Stuttgart
A, B, D, E 170 Normal Strength Plates
FH32, FH36 50 Higher Strength
AH40, DH40, EH40 65
AH32, AH36, DH32, DH36, EH32, EH36 170
360FG, 410FG, 460FG, 490FG, 510FG 100 Boiler & Pressure Vessel
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36, 5Ni
50 Ferritic Low Temperature
Httenwerkstrasse
Postfach 1580
Tel: +49 6381 472197 Fax: +49 6831 473689 Email: mailto:rolf.maier@dillinger.biz Web:http://www.dillinger.de
All plates with specified through thickness properties.
D-66748 Dillingen / Saar
As at 19 March 2007 16 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F./Ingot/Con Cast Steelmaking BGH Edelstahl Freital GmbH Dortmund
alloy, austenitic stainless, duplex stainless,
martensitic stainless*
165 Machinery Bars
Am Stahlwerk 1
D-01705 Freital
Tel: +49 (0)351 646 0 Fax: +49 (0)351 646 2888 Email: mailto:kappelt@schmie-guss.de Web: http://www.bgh.de
Including forged bars
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking BGH Edelstahl Siegen GmbH Dortmund
D-57076 Siegen
Industriestr. 9
Tel: +49 (0)271 701-0 Fax: +49 (0)271 701-300 Email: mailto:peter.hofmann@bgh.de Web:http://www.bgh.de
carbon, carbon-manganese, alloy E.A.F. / Con Cast Steelmaking Benteler Stahl/Rohr GmbH Dortmund
carbon, carbon-manganese, alloy 215 Slabs Semi-Finished
carbon, carbon-manganese, alloy 310 Blooms/Billets
Niederdarmer Str. 5
D-49811 Lingen
Tel: +49 591 80004-0 Fax: +49 591 80004-46 Web: http://www.benteler.de
Slabs, blooms and billets intended for plates, forgings and tubes.
As below E.A.F./Ingot/Con Cast Steelmaking DEUTSCHE EDELSTAHLWERKE GMBH Dortmund
alloy, austenitic stainless 250 Structural Bars
carbon, carbon-manganese, alloy, austenitic
stainless
250 Semi-finished Products
alloy, austenitic stainless 250 Machinery
Auestrae 4
D-58452 Witten
Works Witten
Tel: +49 (0)2302 29-4111 Fax: +49 (0)2302 29-2100 Email:mailto:dieter.jung@dew-stahl.com Web:http://www.dew-stahl.com
As below E.A.F. / Ingot Steelmaking ELEKTROSTAHLWERKE GRDITZ GmbH Dortmund
carbon, carbon-manganese, alloy, austenitic
stainless
Ingots Semi-Finished
D-01609 Grditz
Riesaer Strae 1
Tel: +49 35263 62-611 Fax: +49 35263 62-622 Email: mailto:ilvia.polchow@stahl-groeditz.de Web:http://www.stahl-groeditz.de
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Ingot Steelmaking Edelstahlwerke Buderus AG Dortmund
A 13 Normal Strength Strip
360, 410 13 Boiler & Pressure Vessel
carbon, carbon-manganese, alloy 200 Semi-finished Products Bars
carbon, carbon-manganese, alloy 190 Machinery
Postfach 14 19
D-35573 Wetzlar
Tel: +49 (0)6441 374 0 Fax: +49 (0)6441 374 882 Email: mailto:bjoern.rech@edelstahl.buderus.de Web: http://www.buderus-steel.com
As below E.A.F. / Ingot Steelmaking Edelstahlwerke Sdwestfalen GmbH Dortmund
carbon, carbon-manganese, alloy, austenitic
stainless
80 Structural Bars
Postfach 10 12 20
D-57012 Siegen
Tel: +49 (0)271 808 03 Fax: +49 (0)271 808 3000 Email: mailto:info@ews-stahl.de Web: http://www.ews-stahl.de
As below E.A.F./Ingot/Con Cast Steelmaking Georgsmarienhtte GmbH Dortmund
A, B, D, E 180 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32 180 Higher Strength
alloy 270 Structural
carbon, carbon-manganese 280
U1, U2, U3, R3 155 Chain Cable Stock
D-49124 Georgsmarienhtte
Neue Httenstrae 1
Tel: +49 (0)5401 39-0 Fax: +49 (0)5401 394425 Email: mailto:marketing@gmh.de Web: http://www.georgsmarienhuette-gmbh.de
As below E.A.F. / Con Cast Steelmaking H.E.S. Hennigsdorfer Elektrostahlwerke GmbH Dortmund
carbon, carbon-manganese, alloy 100 Structural Bars
U1, U2 73 Chain Cable Stock
carbon, carbon-manganese, alloy 50 Machinery
Wolfgang-Kntscher-Strae 18
D-16761 Hennigsdorf
Tel: +49 (0)3302 806-0 Fax: +49 (0)3302 806-211 Email: mailto:labor.hes@rivagroup.com Web: http://www.rivagroup.com
A, B, D 20 Normal Strength Sections HSP Hoesch Spundwand und Profil GmbH Dortmund
AH27S, AH32, AH36, DH27S, DH32, DH36 20 Higher Strength
Alte Radstrae 27
D-44147 Dortmund
Ein Unternehmen der Salzgitter Gruppe
Tel: +49 (0)231185-6541 Fax: +49 (0)231 185 6900 Email: mailto:schoeneberg@hsp.spundwand.de Web: http://www.spundwand.de
As at 19 March 2007 17 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 50 Normal Strength Sections Hoesch Schwerter Profile GmbH Dortmund
Eisenindustriestrae 1
D-58239 Schwerte
Tel: +49 (0)2304 106-0 Fax: +49 (0)2304 106-591 Email: mailto:info@hoesch-profile.com Web: http://www.schwerter-spezialprofile.de
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking Httenwerke Krupp Mannesmann GmbH Dortmund
carbon, carbon-manganese, alloy 260 Slabs Semi-Finished
carbon, carbon-manganese, alloy 406 Blooms/Billets
Ehinger Strasse 200
D-47259 Duisburg-Huckingen
Huckingen Works
Tel: +49 (0)203 999-01 Fax: +49 (0)203 999-4411 Email: mailto:post@hkm.de Web: http://www.hkm.de
B, D, E 85 Normal Strength Plates ILSENBURGER GROBBLECH GmbH Dortmund
A 150
AH40, DH40, EH40 50 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
120
360AR, 410AR, 460AR 40 Boiler & Pressure Vessel
360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,
510FG
100
1.5Ni, 3.5Ni, 5Ni, 9Ni 15 Ferritic Low Temperature
LTAH40, LTDH40, LTEH40 50
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
120
Veckenstedter Weg
D-38871 Ilsenburg
All plates with specified through thickness properties.
Q.A. Approved - Approval No. QA019
Tel: +49 39452/85 5530 Fax: +49 39452/85 5733 EMail mailto:manegold@ilsenburger-grobblech.de Web: http://www.ilsenburger-grobblech.de
As below E.A.F. / Con Cast Steelmaking Lech-Stahlwerke GmbH Stuttgart
A, B 100 Normal Strength Bars
carbon, carbon-manganese, alloy 90 Machinery
86405 Meitingen-Herbertshofen
Meitingen-Herbertshofen
Tel: +49 (0)8271/82-527 Fax: +49 (0)8271/82-405 Email:mailto:christian.herrmann@lech-stahlwerke.com
A, B, D, E 50 Normal Strength Plates Mannesmannrhren Mlheim GmbH Dortmund
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50
304L, 316L 50 Austenitic Stainless
Wiesenstrae 36
D-45473 Mlheim an der Ruhr
Tel: +49 (0)208 458-04 Fax: +49 (0)208 458-1918 Email: mailto:stefan.meimeth@mannesmann-mrm.de Web: http://www.mannesmann-mrw.de
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking Mittal Steel Ruhrort GmbH Dortmund
carbon, carbon-manganese, alloy 385 Blooms Semi-Finished
carbon, carbon-manganese, alloy 130 Billets
Postfach 13 07 62
D-47107 Duisburg
Tel: +49 (0)203/52 67353 Fax: +49 (0)203/52 66332 Email: mailto:Hans-Joachim.tubes@mittalsteel.com Web: http://www.mittalsteel.com
As below E.A.F. / Con Cast Steelmaking Peiner Trger GmbH Dortmund
A, B, D, E 40 Normal Strength Sections
AH32, AH36, DH32, DH36, EH32, EH36 40 Higher Strength
D-31226 Peine
Gerhard-Lucas-Meyer Str. 10
Tel: +49 5171 91 9527 Fax: +49 5171 91 9373 Contact: Herr Maly Email: maly.k@salzgitter-ag.de Website: www.peinertraeger.de
A, B, D, E 250 Normal Strength Plates REINER BRACH GmbH & Co. KG Bremen
AH32, AH36, DH32, DH36, EH32, EH36 120 Higher Strength
AH27S, DH27S, EH27S 250
460FG, 490FG, 510FG 120 Boiler & Pressure Vessel
360FG, 410FG 150
Auf den Delben 35
D-20237 Bremen
Tel: +49 421 643 62-36 Fax: +49 421 643 62-32 Email mailto:frank-santuari@brach.de Web:http://www.brach.de
A 40 Normal Strength Sections SAARSTAHL AG Stuttgart
A 40 Normal Strength Bars
U1, U2, U3, R3 40 Chain Cable Stock
D-66511 Neunkirchen
Works Neunkirchen
Tel: +49 6898 104293 Fax: +49 6898 1054293 Email: mailto:mark.bleymehl@saarstahl.com Web:http://www.saarstahl.com
As at 19 March 2007 18 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking SAARSTAHL AG Stuttgart
A 32 Normal Strength Sections
A 160 Normal Strength Bars
U1, U2, U3, R3 100 Chain Cable Stock
Bismarckstrasse 57 - 59
D-66330 Vlklingen
Works Vlklingen
Tel: +49 6898 10 4293 Fax: +49 6898 10 54293 Email: mailto:mark.bleymehl@saarstahl.com Web:http://www.saarstahl.com
As below E.A.F. / Con Cast Steelmaking STAHLWERK THRINGEN GMBH Dortmund
A, B 25 Normal Strength Sections
AH32, AH36, DH32, DH36 25 Higher Strength
D-07333 Unterwellenborn
Kronacher Strae 6
Tel +49 3671 445404 Fax +49 3671 445338 Email: mailto:gerd.hoffmann@stahlwerk-thuringen.de Internet http://www.stahlwerk-thueringen.de
As below E.A.F. / Ingot Steelmaking Schmidt + Clemens GmbH + Co. KG Dortmund
carbon, carbon-manganese, alloy, austenitic
stainless
50 Structural Bars
D-51789 Lindlar
Bundesstrasse
Tel: +49 (0)22 66/920 Fax: +49 (0)22 66/92370 Email: mailto:gusstechnik@schmidt-clemens.de Web http://www.schmidt-clemens.de
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking Stahlwerk Bous GmbH Stuttgart
D-66359 Bous
Saarstrae
Tel: +49 6834 81551 Fax: +49 6834 81586 Email: mailto:mmuth@stahlwerk-bous.de Web http://www.stahlwerk-bous.de
Ingots up to 60 tonne and 2300 mm dia.
As below E.A.F./Ingot/Con Cast Steelmaking ThyssenKrupp Nirosta GmbH Dortmund
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,
347
8 Austenitic Stainless Strip
Oberschlesienstrae 16
D-47807 Krefeld
Works Krefeld
Tel: +49 (0)211 7107-0 Fax: +49 (0)211 7107-455 Email: mailto:thomas.seifert@thyssenkrupp.com Web: http://www.nirosta.de
A, B, D, E 20 Normal Strength Strip ThyssenKrupp Steel AG, Duisburg Dortmund
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20 Boiler & Pressure Vessel
Kaiser-Wilhelm-Strae 100
D-47166 Duisburg
Works Bochum
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
As below B.O.S. / Con Cast Steelmaking ThyssenKrupp Steel AG, Duisburg Dortmund
As below 255 Slabs Semi-Finished
A, B, D, E 20 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20 Boiler & Pressure Vessel
Works Beeckerwerth
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
As below B.O.S. / Con Cast Steelmaking ThyssenKrupp Steel AG, Duisburg Dortmund
A, B, D, E 20 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20 Boiler & Pressure Vessel
Works Bruckhausen
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
A, B, D, E 150 Normal Strength Plates ThyssenKrupp Steel AG, Duisburg Dortmund
FH27S, FH32, FH36 50 Higher Strength
AH40, DH40, EH40 60
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
50 Ferritic Low Temperature
UNS S31803 35 Duplex Stainless
A, B, D, E 20 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20 Boiler & Pressure Vessel
Works Duisburg-Sd
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:joachim.gottlieb@thyssenkrupp.com Web: http://www.thyssenkrupp-stahl.com
Specified through thickness properties on all normal and higher strength steel grade plates.
As at 19 March 2007 19 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Hungary
carbon, carbon-manganese, alloy E.A.F. / Con Cast Steelmaking DAM 2004 Acl-s Hengerm Kereskedelmi s
Szolgltat Kft.
Budapest
As above E.A.F. / Ingot
A, B, D, E 18 Normal Strength Sections
AH32, AH36, DH32, DH36, EH32, EH36 18 Higher Strength
A, B, D, E 60 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32, EH36 60 Higher Strength
3540 MISKOLC
Vasgyri u. 43
Tel: +36 46 530 931 Fax: +36 46 370 236 Email: mailto:agnes.takacs@dam2004.hu WeB: http://www.dam2004.hu
As below B.O.S. / Con Cast Steelmaking DUNAFERR Dunai Vasm Rszvnytrsasg Budapest
A, B, D, E 13 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
13 Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,
510FG
13 Boiler & Pressure Vessel
A, B, D, E 13 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
13 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 13 Boiler & Pressure Vessel
2400 Dunajvros
Vasm Tr 1-3
Tel: +36 25 584 460 Fax: +36 25 584 490 Email: mailto:hevesine@rt.dunaferr.hu Web: http://www.dunaferr.hu
B, D, E 35 Normal Strength Plates DUNAFERR LRINCI HENGERM KFT Budapest
A 100
AH32, AH36, DH32, DH36, EH32, EH36 60 Higher Strength
360, 410 35 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 60
1184 Budapest
Hengersor U38
Tel: +36 1 296 2200/206 Fax: +36 1 296 2201 Email: mailto:zizi@dlhkft.hu
India
As below E.A.F. / Con Cast Steelmaking ESSAR STEEL LTD. Mumbai
A, B 20 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36 20 Higher Strength
360FG, 410FG 20 Boiler & Pressure Vessel
Dist. Surat
Gujarat
Hazira - 394 270
Tel: +91 261 2872400 Fax: +91 2872736 Email mailto:sbhat@essar.com Web http://www.essar.com
austenitic stainless E.A.F./A.O.D./Con Cast Steelmaking Jindal Stainless Ltd. Yamunanagar
austenitic stainless E.A.F./V.O.D./Con Cast
304L, 316L, 317L, 321, 347 53 Austenitic Stainless Plates
Delhi Road
Hisar 125 005 (Haryana)
Post Box No. 6
Tel: +91 1662 222471 Fax: +91 1662 220476 Email: mailto:hsr.maheshwari@jslhsr.com
As below E.A.F./Ingot/Con Cast Steelmaking KALYANI CARPENTER SPECIAL STEELS LTD. Pune
carbon, carbon-manganese, alloy 150 Structural Bars
carbon, carbon-manganese, alloy 250 Semi-finished Products
Mundhwa
Pune 411 036
Tel: +91 20 26823344 Fax: +91 20 26824498 Email: mailto:kgnmohan@kcssl.com Web: http://www.kalyanicarpenter.com
As below E.A.F. / Ingot Steelmaking MAHINDRA UGINE STEEL CO., LTD. Mumbai
carbon, carbon-manganese, alloy, austenitic
stainless steel
Blooms/Billets Semi-Finished
A 50 Normal Strength Sections
A 200 Normal Strength Bars
Khopoli
Dist. Raigad
Khopoli Works
Jagdish Nagar
Tel: +91 952192 263318 (263347) Fax: +91 952192 263582 (263076) Email mailto:drsbsarkar@muscoindia.com
Maharashtra 410 216
As at 19 March 2007 20 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking STEEL AUTHORITY OF INDIA LTD. Bhilai
A, B, D 75 Normal Strength Plates
360AR, 410AR, 360, 410 63 Boiler & Pressure Vessel
360FG, 410FG 75
Bhilai 490 001
Chhattisgarh
Bhilai Steel Plant
Tel +91 788 2892791 Fax +91 788 2222040 Email:mailto:jagdishsingh@sail-bhilaisteel.com
As below B.O.S. / Con Cast Steelmaking STEEL AUTHORITY OF INDIA LTD. Calcutta
A, B 52 Normal Strength Plates
360, 410, 360FG, 410FG 35 Boiler & Pressure Vessel
360AR, 410AR 40
Rourkela 769 011
Orissa
Rourkela Steel Plant
Tel +91 (0)661 511210 Fax +91 (0)661 890183 Email mailto:brai@sail-steel.com
As below B.O.S. / Ingot Steelmaking STEEL AUTHORITY OF INDIA LTD. Bangalore
As below E.A.F. / Ingot
A 50 Normal Strength Sections
A 50 Normal Strength Bars
carbon, carbon-manganese, alloy 140 Structural
Bhadravati-577301
Karnataka
Visvesvaraya Iron & Steel Plant
Tel: +91 (0) 818 671620 Fax: +91 (0) 818 671748 Email: mailto:edvisl@sancharnet.in Web: http://www.sail.com
As below B.O.S. / Con Cast Steelmaking TATA STEEL LIMITED Calcutta
A 50 Normal Strength Plates
360AR, 410AR 50 Boiler & Pressure Vessel
A 12 Normal Strength Strip
Kolkata 700 071
43 Chowringhee Road
Tel: +91 (33) 22889251 Fax: +91 (33) 22887255/22881396 Email mailto:rakesh@itd.tatasteel.com Web http://www.tata.com
austenitic stainless steel IF/AOD/Ingot/ConCast Steelmaking VIRAJ ALLOYS Ltd. Mumbai
austenitic stainless steel 200 Blooms/Billets Semi-Finished
Dist. Thane
Maharashtra 401-506
G-23 MIDC,Tarapur Industrial Area
Tel: +91 2525 271365-68 Fax: +91 2525 270431/72448 Email mailto:val@viraj.com
Indonesia
B, D 25 Normal Strength Plates PT. GUNAWAN DIANJAYA STEEL Jakarta
A 40
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
360AR, 410AR 25 Boiler & Pressure Vessel
Jl. Margomulyo No. 29A
Greges-Asemrowo
Tel: +62 31 7490598 Fax: +62 31 7490581/7482109
Email: mailto:gunawan@gds.co.id Web http://www.gunawansteel.com
Surabaya 60183
A, B 50 Normal Strength Plates PT. Gunung Raja Paksi Jakarta
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
A 12 Normal Strength Strip
360, 410 12 Boiler & Pressure Vessel
Jl. P. Jayakarta No. 105G
Jakarta 10730
Tel +62 21 890 0222 Fax +62 21 890 1588 Email: mailto:gunung@cbn.net.id
A, B 25 Normal Strength Plates PT. JAYA PARI STEEL Tbk. Surabaya
Jl Margomulyo No. 4
Tandes
Tel: +62 31 7491288 Fax:+62 31 7491714 Email:mailto:jayapari@rednet.id
Surabaya 60186
As below E.A.F. / Con Cast Steelmaking PT. KRAKATAU STEEL (PERSERO) Jakarta
A 25 Normal Strength Plates
Jl. Industri No. 5
PO. Box 14
Divisi P & PM (QA)
Tel: +62 (0)21 523 5559 Fax: +62 (0)21 520 1608 Email: mailto:marsidon.s@krakatausteel.com Web: http://www.krakatausteel.com
Cilegon 42435
As at 19 March 2007 21 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Italy
As below B.O.S./Ingot/Con Cast Steelmaking A.B.S. Acciaierie Bertoli Safau S.p.A. Trieste
As below E.A.F./Ingot/Con Cast
carbon, carbon-manganese, alloy 170 Structural Bars
U1, U2, U3 78 Chain Cable Stock
carbon, carbon-manganese, alloy 170 Semi-finished Products
carbon, carbon-manganese, alloy 170 Machinery
33050 Pozzuolo del Friuli (UD)
Via Butrio, 28
Tel +39 (0)432 613211 Fax +39 (0)432 613218 E-mail: mailto:quality@absacciai.it
carbon, carbon-manganese, alloy, medium alloy E.A.F. / Ingot Steelmaking A.S.O. SIDERURGICA S.r.L. Brescia
25035 Ospitaletto
Brescia
Via Seriola no. 122
Tel: +39 (0)30 6841011-(0)30 6841165 Fax: +39 (0)30 6841012 Email: mailto:Info@aso.it Web: http://www.aso.it
As below, carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking ACCIAIERIA FONDERIA CIVIDALE S.P.A. Trieste
carbon, carbon-manganese, alloy 35 Ingots Semi-Finished
Zona Industriale no. 44
33043 Cividale del Friuli
Via delle Industrie
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,
Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemical
composition and enables them to achieve the required mechanical properties
Tel +39 432 706911 Fax +39 432 706920 Email:mailto:afcspa@afcspa.com
(Udine)
A, carbon, carbon-manganese, alloy, stainless E.A.F./Ingot/Con Cast Steelmaking ACCIAIERIE VALBRUNA S.P.A. Venice
A 10 Normal Strength Sections
A 155 Normal Strength Bars
austenitic stainless, precipitation hardened
stainless*, martensitic stainless*
155 Machinery
duplex stainless 205
36100 Vicenza
Viale Della Scienza, 25 z.i.
Tel: +39 0444 968211 Fax: +39 0444 968182 Email:mailto:quality@valbruna.it Web:http://www.acciaierie-valbruna.com
Duplex grade UNS 31803 for Machinery Bar.
Welding and weld repair of duplex stainless steel bar not permitted.
As below E.A.F./Ingot/Con Cast Steelmaking ACCIAIERIE VALBRUNA S.P.A. Venice
as below A.O.D./Ingot/Con Cast
austenitic stainless, duplex stainless,
precipitation hardened stainless*, martensitic
stainless*
73 Machinery Bars
Via A Volta 4
39100 Bolzano
39100 Bolzano
* Accepted for approved applications
Tel; +39 (0)471 924111 Fax: +39 (0)471 924355
Email: mailto:info@valbruna.it Web: http//www.acciaierie-valbruna.com
carbon, carbon-manganese, alloy, A, B, D, AH32,
AH36, DH32, DH36
E.A.F. / Con Cast Steelmaking ACCIAIERIE VENETE S.p.A. Venice
carbon, carbon-manganese, alloy 170 Structural Bars
carbon, carbon-manganese, alloy 120 Semi-finished Products
carbon, carbon-manganese, alloy 120 Machinery
35020 Camin (Padova)
Camin Works
Riviera Francia, 9
Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666 Email: mailto:commercial.dep@acciaierievenete.com Web: http://www.acciaierievenete.com
As below E.A.F. / Con Cast Steelmaking AFV ACCIAIERIE BELTRAME S.p.A. Venice
A, B, D, E 20 Normal Strength Sections
AH32, AH36, DH32, DH36 20 Higher Strength
Viale della Scienza 81/A
36100 Vicenza
Tel +39 0444 967111 Fax +39 0444 348585 Email: mailto:info@beltrame.it Web site http://www.beltrame.it
A 20 Normal Strength Strip AFV ACCIAIERIE BELTRAME S.p.A. Venice
360, 410 20 Boiler & Pressure Vessel
A, B, D, E 40 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36 40 Higher Strength
Via del Commercio, 15
30175 Marghera (VE)
Stabilimento di Marghera
Tel +39 041 2583711 Fax +39 041 2583819 E-mail:mailto:info@beltrame.it
As at 19 March 2007 22 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D 22 Normal Strength Fabricated Sections ARMANDO CIMOLAI CENTRO SERVIZI Srl Trieste
AH32, AH36, DH32, DH36 22 Higher Strength
Via Masieres, No.32
33080 San Quirino (PN)
Tel: +39 (0)434 919292 Fax: +39 (0)434 919266
carbon, carbon-manganese, alloy E.A.F./Ingot/Con Cast Steelmaking Acciaieria di Rubiera S.p.A. Ravenna
carbon, carbon-manganese, alloy 180 Billets Semi-Finished
42013 S. Donnino di Casalgrande (R.E.)
Via XXV Aprile, 64
Tel: +39 059 334195 Fax: +39 059 828220 Email: mailto:frtesti@tin.it
Address for orders: Acciaieria di Rubiera S.p.A. , Via San Cataldo, 115, 41100 Modena, Italy.
carbon, carbon-manganese E.A.F. / Ingot Steelmaking Alfa Acciai S.p.A. Brescia
carbon, carbon-manganese Ingots Semi-Finished
carbon, carbon-manganese Blooms/Billets
25134 Brescia
Via S. Polo, 152
Tel +39 30 23911 Fax +39 30 2301963 Email: mailto:e.salvi@alfaacciai.it Web:http://www.alfaacciai.it
A, B, D 22 Normal Strength Fabricated Sections CIMOLAI S.p.A Trieste
AH32, AH36, DH32, DH36 22 Higher Strength
Via Tessere 9
33070 - Polcenigo (PN)
Tel: +39 (0)434 748822 Fax: +39 (0)434 749139 Email mailto:stab_polcenigo@cimolai.com Web http://www.cimolai.com
A, D 50 Normal Strength Fabricated Sections EUROGROUP S.p.A. Trieste
AH36, DH36 50 Higher Strength
34074 MONFALCONE (GO)
Via Timavo - Z. I. Lisert
Tel: +39 481 495111 Fax: +39 481 495112 Contact: Mr Stefano Vinoni
A 30 Normal Strength Fabricated Sections Eurotravi S.r.l. Venice
Via Del Lavoro Nr 12
31016 Cordignano
Tel +39 0438 995350 Fax +39 0438 995250 Email: mailto:eurotravi.tec@nline.it Web: http://www.nline/eurotravi/
Treviso
A, B 50 Normal Strength Sections Ferriera Sider Scal S.p.A. Milan
AH27S, AH32, AH36, DH27S, DH32, DH36 30 Higher Strength
A, B 83 Normal Strength Bars
Via Sempione, 34
28844 Villadossola (VB)
Stabilimento Di Villadossola
Tel +39 0324 579811 Fax +39 0324 579806
As below B.O.S. / Con Cast Steelmaking ILVA S.p.A. Genoa
A, B, D, AH27S, AH32, AH36, DH27S, DH32,
DH36
260 Blooms/Billets Semi-Finished
16154 Genova-Cornigliano
Genoa Works
Via Pionieri e Aviatori d'Italia No. 8
Tel:+39 010 6076473 Fax: +39 010 6076311 Email: mailto:sergio.fera@rivagroup.com
As below B.O.S. / Con Cast Steelmaking ILVA S.p.A. Taranto
A, B, D, E 80 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
80 Higher Strength
A 10 Normal Strength Strip
AH27S, AH32, AH36 10 Higher Strength
Via Appia KM 648
Taranto 74100
Taranto Works
Tel: +39 02 307 00 775 Fax: +39 02 307 00 285 Email: mailto:commerciale.lamiere@rivagroup.com Web: http://www.rivagroup.com
Specified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be added
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Ingot Steelmaking LUCCHINI SIDERMECCANICA S.p.A. Brescia
Via G. Pagalia N.45
24065 Lovere
Lovere Works
Tel: +39 035 963535 Fax: +39 035 963488 Email: mailto:s.cantini@lucchini.it Web: http://www.lucchini.it
Bergamo
A, B, D, E 50 Normal Strength Fabricated Sections OFFICINE NORD EST S.r.l
Officine Nordest s.r.l.
Trieste
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
Via Ungaesca, No. 12
33080 San Quirino (PN)
Tel: +39 (0)434 919091 Fax: +39 (0)434 918646
As at 19 March 2007 23 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D 8 Normal Strength Sections OLIFER-ACP S.P.A. Brescia
AH32, AH36, DH32, DH36 8 Higher Strength
Loc.Motta Alta, 14
24050 Cividate Al Piano
ROLLING MILL - ODOLO
Bresica Work
Tel +39 365 826088 Fax +39 365 860727 Email: mailto:olifer@mail.olifer.com Web:http://www.olifer.com
Bergamo
A, B, D, AH32, AH36, DH32, DH36 E.A.F. / Con Cast Steelmaking OLIFER-ACP S.P.A. Brescia
Loc. Motta Alta 14
Cividate Al Piano
STEELMAKING
Bergamo Works
Tel: +39 363 97193/4 Fax: +39 363 976666 Email: mailto:direzione-cividate@olifer.com Web http://www.olifer.com
A 30 Normal Strength Plates PALINI & BERTOLI S.p.A. Trieste
AH32, AH36 30 Higher Strength
Via E. Fermi, 28 - 33058
S. Giorgio di Nogaro (UD)
Tel: +39 0431 62 3111 Fax: +39 0431 62 1244 Email: mailto:aantoniutti@paliniebertoli.it
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
30 Higher Strength Sections Siderval S.p.A. Milan
Via Roma 39C
23018 Talamona
Tel: +39 342 670662 Fax: +39 342 670400 Email: mailto:siderval@siderval.it Web: http://www.siderval.it
Sondrio
A, B, D, E 60 Normal Strength Plates TRAMETAL S.p.A. Trieste
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
60 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 60 Boiler & Pressure Vessel
Via Enrico Fermi, 44
33058 San Giorgio di Nogaro (UD)
Tel: +39 010 57 62911 Fax: +39 010 57 62990 Email:mailto:rre@trametal.it Web:http://www.trametal.it
304L, 316L, 321 6 Austenitic Stainless Strip ThyssenKrupp Acciai Speciali Terni SpA con Unico
Socio
Milan
Corso Regina Margherita, 400
10151 Torino
Turin Works
Tel: +39 11 4511272 Fax: +39 11 4511442 Email: mailto:l.montiglio@acciaiterni.it
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F./Ingot/Con Cast Steelmaking ThyssenKrupp Acciai Speciali Terni SpA con Unico
Socio
Naples
304L, 316L, 321 6 Austenitic Stainless Strip
Viale B. Brin, 218
05100 Terni
Terni Works
Tel: +39 744 490733 Fax: +39 744 470517 Email mailto:m.montesi@acciaiterni.it Web:http://www.acciaiterni.it
Japan
carbon, carbon-manganese, austenitic stainless E.A.F. / Ingot Steelmaking AICHI STEEL CORPORATION Kobe
A 180 Normal Strength Bars
304L, 316L 180 Austenitic Stainless
U1, U2, U3 120 Chain Cable Stock
carbon, carbon-manganese, alloy, austenitic
stainless
125 Machinery
Arao-machi
Tokai-shi
Chita Plant
1, Wano-Wari
Tel: +81 52 603 9353 Fax: +81 52 603 9898 Email: mailto:hirohama@he.aichisteel.co.jp
Aichi-ken, 476-8666
304L, 316L 150 Austenitic Stainless Bars AICHI STEEL CORPORATION Kobe
Kariya-shi
Aichi-ken
Kariya Plant
3-6, Toyota-cho
Tel +81 566 21 9130 Fax +81 566 23 6925 Email: mailto:fujiki@he.aichi-steel.co.jp
448-0848
As below E.A.F. / Con Cast Steelmaking CHUBU STEEL PLATE CO., LTD. Kobe
A, B 50 Normal Strength Plates
360AR, 410AR 40 Boiler & Pressure Vessel
As at 19 March 2007 24 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Nakagawa-ku
Nagoya
5-1, Kousudori
Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:k_murayama@chubukohan.co.jp
As below E.A.F. / Ingot Steelmaking DAIDO STEEL CO., LTD. Kobe
carbon, carbon-manganese 270 Structural Bars
39, Motohama-machi
Tokai-shi
Chita Plant
Tel: +81 562 33 3106 Fax: +81 562 33 6598 Email: mailto:y-kitagawa@ac.daido.co.jp Web: http://www.daido.co.jp
Aichi-ken
carbon, carbon-manganese 160 Structural Bars DAIDO STEEL CO., LTD. Kobe
carbon, carbon-manganese 160 Machinery
Minami-ku
Nagoya-shi
Hoshizaki Plant
2-30, Daido-cho
Tel: +81 52 611 2525 Fax: +81 52 611 2528 EMail mailto:D3521@so.diido.co.jp Web:http://www.daido.co.jp
carbon, carbon-manganese, alloy, austenitic
stainless
60 Structural Bars DAIDO STEEL CO., LTD. Yokohama
2-4-1 Yakoh
Kawasaki-ku
Kawasaki Plant
Tel +81 44 266 3763 Fax +81 44 266 3768
Kawasaki-city, Kanagawa Pref.
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking DAIDO STEEL CO., LTD. Yokohama
Shibukawa-shi
Gunma 377-0007
Shibukawa Plant
500, Ishihara
Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:t-furuse@ac.daido.co.jp
As below B.O.S. / Con Cast Steelmaking DAISAN STEEL Co., Ltd. Yokohama
As below E.A.F. / Con Cast
A, B 28 Normal Strength Bars
Kohto-ku
Tokyo 136-0075
Shinsuna Works
3-2-1, Shinsuna
Tel: +81 (0)3 3644 1101 Fax: +81 (0)3 3664 1100 Email: mailto:sshimomura@daisan-seiko.co.jp
As below E.A.F. / Con Cast Steelmaking GODO STEEL LTD. Kobe
A 15 Normal Strength Sections
A 150 Normal Strength Bars
U3 100 Chain Cable Stock
U1, U2 150
Hyogo pref.
2946 Nakashima Shikamaku
Himeji-city
Tel. +81 (0)792 34 9332 Fax +81(0)792 34 9538
As below E.A.F. / Ingot Steelmaking HITACHI METALS, LTD. Kobe
A 150 Normal Strength Bars
alloy, austenitic stainless 150 Structural
Yasugi-shi
Shimane-ken
Yasugi Works
2107-2, Yasugi-cho
Tel: +81 (0)854 22 1908 Fax: +81 (0)854 23 0281 Email mailto:ryuichi_utsunomiya@hitachi-metals.co.jp Web http://www.hitachi-metals.co.jp
As below E.A.F. / Con Cast Steelmaking JFE BARS & SHAPES CORPORATION Kobe
B, D, E 25 Normal Strength Sections
A 32
EH32, EH36 25 Higher Strength
AH32, AH36, DH32, DH36 32
1280, Hosoe
Shikama-ku
Himeji Works
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:hiroshi-satou@jfe-bs.co.jp Internet http://www.jfe-bs.co.jp
Himeji 672-8064
As below E.A.F. / Con Cast Steelmaking JFE BARS & SHAPES CORPORATION Yokohama
A, B, D 32 Normal Strength Sections
AH32, AH36, DH32, DH36 32 Higher Strength
Kashima-gun
Ibaraki Pref.
Kashima Works
7 Minamihama, Kamisu-machi
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201 Email: mailto:toshiyuki_nakano@jfe-bs.co.jp
314-0111
As at 19 March 2007 25 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As Below B.O.S./E.A.F./Ingot/Con Cast Steelmaking JFE STEEL CORPORATION Kobe
A, B, D, E 200 Normal Strength Plates
AH42, FH27S, FH32, FH36 50 Higher Strength
DH42, DH46, DH50, DH55, DH62, DH69, EH42,
EH46, EH50, EH55, EH62, EH69
75
AH40, DH40, EH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
150
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410 100
360FG, 410FG, 460FG, 490FG, 510FG 134
9Ni 40 Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
50
304L, 316L 50 Austenitic Stainless
E/304L, E/316L 30 Clad
A, B, D, AH27S, AH32, AH36, DH27S, DH32,
DH36, EH27S, EH32, EH36
50 Tapered
A, B, D, AH27S, AH32, DH27S, DH32 40 Differential Thickness
A, B 16 Normal Strength Strip
360, 410 16 Boiler & Pressure Vessel
A, B, D 32 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
32 Higher Strength
carbon, carbon-manganese 400 Structural Bars
U1, U2 130 Chain Cable Stock
alloy 165 Machinery
carbon-manganese 190
Kawasaki-Dori
Kurashiki
West Japan Works (Kurashiki)
1 Mizushima
Tel: +81 (0)86 447 2730 Fax: +81 (0)86 447 2735 Email: mailto:ma-inoue@kawasaki-steel.co.jp
Specified through thickness properties on all plate grades.
MQS Approved - Approval No. MQS 022
As below B.O.S. / Con Cast Steelmaking JFE STEEL CORPORATION Mihara
A, B, D, E 120 Normal Strength Plates
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40, FH27S,
FH32, FH36, FH40
80 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
460FG, 490FG, 510FG 55
360FG, 410FG 70
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36
40 Ferritic Low Temperature
304L, 304LN, 316L, 316LN, 317L, 317LN 55 Austenitic Stainless
EH36/304L, EH36/316L 30 Clad
A, B, D, E 12 Normal Strength Strip
AH27S, AH32 8 Higher Strength
460FG, 490FG 8 Boiler & Pressure Vessel
360, 410, 360FG, 410FG 12
E 18 Normal Strength Sections
A, B, D 35
AH40, DH40, EH40, FH27S, FH32, FH36 18 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
36
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36
18 Ferritic Low Temperature
Fukuyama-city
Hiroshima-pref.
West Japan Works (Fukuyama)
1, Kokan-cho
Tel. (0)84 945 3160 Fax (0)84 945 3101 EMail mailto:k-nibu@jfe-steel.co.jp Web http://www.jfe-steel.co.jp
MQS Approved - Approval No. MQS 005
721-8510
As below B.O.S. / Con Cast Steelmaking JFE STEEL CORPORATION Yokohama
A, B, D, E 100 Normal Strength Plates
FH27S, FH32, FH36 42 Higher Strength
AH42, DH42, EH42 83
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
90
As at 19 March 2007 26 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Japan
360AR, 410AR 40 Boiler & Pressure Vessel Plates JFE STEEL CORPORATION Yokohama
360, 410, 460FG, 490FG, 510FG 50
360FG, 410FG 100
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
42 Ferritic Low Temperature
Kawasaki-ku
Kawasaki
East Japan Works (Keihin)
1-1, Ohgishima
Tel: +81 44 322 1185 Fax: +81 44 322 1510 Email: mailto:h-kibe@jfe-steel.co.jp
All plate grades with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 034
210-0868
As below B.O.S. / Con Cast Steelmaking KOBE STEEL LTD. Kobe
As below B.O.S. / Ingot
As below E.A.F. / Con Cast
As below E.A.F. / Ingot
A, B, D, E 150 Normal Strength Plates
DH42, DH46, DH50, DH55, DH62, DH69, EH42,
EH46, EH50, EH55, EH62, EH69, FH40, FH42,
FH46, FH50, FH55, FH62, FH69
50 Higher Strength
AH40, DH40, EH40 80
FH27S, FH32, FH36 90
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100
360AR, 410AR, 460AR 40 Boiler & Pressure Vessel
360, 410, 460, 490, 460FG, 490FG, 510FG 90
360FG, 410FG 100
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
90 Ferritic Low Temperature
A,B, D,E, HTS up to EH36 50 Differential Thickness
A, B, D 13 Normal Strength Strip
360FG, 410FG 13 Boiler & Pressure Vessel
1 Kanazawa-cho
Kakogawa-city
Kakogawa Works
Tel: +81 794 36 1151 Fax: +81 794 36 2079 Email: mailto:aa14011@steel.kobelco.co.jp
All grades with specified through thickness properties.
MQS Approved - Approval No. MQS 009
Hyogo-pref.
As below B.O.S./Ingot/Con Cast Steelmaking KOBE STEEL LTD. Kobe
A 250 Normal Strength Bars
U1, U2, U3 160 Chain Cable Stock
carbon, carbon-manganese, alloy 250 Semi-finished Products
carbon, carbon-manganese, alloy 250 Machinery
Nada-ku
Kobe
Kobe Works
2 Nadahama-Higashimachi
Tel +81 78 882 8056 Fax +81 78 882 8204 Email: mailto:horikawa.kenichi@steel.kobelco.co.jp
As below E.A.F. / Con Cast Steelmaking KYOEI STEEL LTD. Nagasaki
A 16 Normal Strength Sections
A 53 Normal Strength Bars
Sanyo-Onoda City
Yamaguchi Prefecture
Yamaguchi Division
Oaza Onoda 6289-18
Tel: +81 836 83 6172 Fax: +81 836 83 0839
756-0817
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Ingot Steelmaking MITSUBISHI STEEL MFG. CO., LTD. Yokohama
Utsunomiya City
Tochigi
Utsunomiya Works
1, Hiraide Kogyo Danchi
Tel: +81 (0)28 661 4123 Fax: +81 (0)28 664 1685
321-0905
As at 19 March 2007 27 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
as below 20 Ingots Semi-Finished MITSUBISHI STEEL MURORAN INC. Yokohama
As below 515 Blooms/Billets
carbon, carbon-manganese, alloy 270 Structural Bars
carbon, carbon-manganese, alloy 210 Machinery
Muroran City
Hokkaido
Muroran Works
12, Naka-machi
Tel: +81 (0)143 41 2832 Fax: +81 (0)143 41 2869
050-0087
A 38 Normal Strength Bars NIHON STEEL CO., LTD. Kobe
11, Rinkai-cho
Kishiwada City
tel: +81 724 23 5151 Fax: +81 724 39 8357 Email mailto:matsukura@nihon-steel.co.jp
Osaka
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking NIPPON STEEL & SUMIKIN Nagasaki
As below E.A.F. / Con Cast
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,
347, 304*, 316*, 317LN(MOD)*
55 Austenitic Stainless Plates
A/304L, D/304L, D/316L 40 Clad
2108-1, Oaza Maeda Aza Hato
Yawata Higashi-ku
STAINLESS STEEL CORPORATION
Yawata Works
* Grades 304,.316 and 317LN(MOD) may be accepted for approved applications.
Tel; +81 93 672 2288 Fax: +81 93 672 2251 Email: mailto:umeno.masaki@ns-sc.co.jp
Kitakyushu, Fukuoka
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Con Cast Steelmaking NIPPON STEEL & SUMIKIN Nagasaki
304L, 316L 8 Austenitic Stainless Plates
304L, 316L 8 Austenitic Stainless Strip
3434 Shimata
Hikari City
STAINLESS STEEL CORPORATION
Production Division, Hikari Works
Tel +81 833 71 5029 Fax +81 833 71 5184 Email: mailto:shimizu.tsunehiro@ns.sc.co.jp Web: http://www.ns-sc.co.jp
Yamaguchi 743-8550
As below B.O.S. / Con Cast Steelmaking NIPPON STEEL CORPORATION Kobe
A, B, D 20 Normal Strength Plates
360AR, 410AR 20 Boiler & Pressure Vessel
Hirohata-ku
Himeji-shi
Hirohata Works
1, Fuji-cho
Tel: +81 792 36 1163 Fax: +81 792 37 8963 Email:aushino@hirohata.nsc.co.jp
Hyogo-pref.
As below B.O.S. / Con Cast Steelmaking NIPPON STEEL CORPORATION Yokohama
As below B.O.S. / Ingot
A, B, D, E 100 Normal Strength Plates
AH42, AH46, AH50, DH42, DH46, DH50, EH42,
EH46, EH50, FH42, FH46, FH50
50 Higher Strength
AH40, DH40, EH40, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
100
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
LHAH42, LTAH46, LTAH50, LTDH42, LTDH46,
LTDH50, LTEH42, LTEH46, LTEH50, LTFH42,
LTFH46, LTFH50
50 Ferritic Low Temperature
LTAH40, LTDH40, LTEH40, LTFH40 80
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
100
A,B,D,E, HTS up to EH40 50 Tapered
A,B,D,E, HTS up to EH40 50 Differential Thickness
A, B 26 Normal Strength Strip
360, 410 25 Boiler & Pressure Vessel
A, B, D 24 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36 19 Higher Strength
Kimitsu-shi
Chiba-ken
Kimitsu Works
1 Kimitsu
Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727 Email: mailto:kurogi@to.kimitsu.nsc.co.jp
All plate grades with specified through thickness properties.
299-1141
As at 19 March 2007 28 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As Below B.O.S./E.A.F./Ingot/Con Cast Steelmaking NIPPON STEEL CORPORATION Yokohama
A, B 200 Normal Strength Bars
AH32, AH36, DH32 200 Higher Strength
U1, U2, U3, R3, R3S, R4 136 Chain Cable Stock
API-2F 152
Muroran City
Hokkaido
Muroran Works
12, Naka-machi
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783
050-8550
As below B.O.S./Ingot/Con Cast Steelmaking NIPPON STEEL CORPORATION Kobe
A, B, D, E 130 Normal Strength Plates
FH27S, FH32, FH36 40 Higher Strength
AH40, DH40, EH40 50
DH42, DH46 70
DH50, DH55, DH62, DH69 200
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
210
360AR, 410AR 40 Boiler & Pressure Vessel
360, 410 115
360FG, 410FG, 460FG, 490FG, 510FG 120
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
40 Ferritic Low Temperature
Tokai-machi
Tokai-city
Nagoya Works
3, 5 Chome
Tel +81 52 603 7225 Fax +81 52 603 7229 Email: okayama@nagoya.nsc.co.jp
All grades and thicknesses with specified through thickness properties (Z35)
Aichi Pref. 476-8686
As below B.O.S. / Con Cast Steelmaking NIPPON STEEL CORPORATION Nagasaki
A, B, D, E 100 Normal Strength Plates
DH42, EH42, FH42 50 Higher Strength
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100
360AR, 410AR, 460AR 40 Boiler & Pressure Vessel
360, 410, 460, 490 90
360FG, 410FG, 460FG, 490FG, 510FG 100
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36, LTFH40
80 Ferritic Low Temperature
A, B, D, E, A,B,D,E, AH27S, AH32, AH36,
DH27S, DH32, DH36, EH27S, EH32, EH36
50 Tapered
A,B,D 35 Differential Thickness
A,B, A,B,D,E, AH27S, AH32, AH36, DH27S,
DH32, DH36, EH27S, EH32, EH36
50
A 12 Normal Strength Strip
AH27S, AH32, AH36 12 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
Oita City
Oita Prefecture
Oita Works
1, Oaza Nishinotsu
Tel +81 97 553 2122 Fax +81 97 553 2379 Email: mailto:nishi-s@oita.nsc.co.jp
All plates with specified through thickness properties.
Q.A. Approved - Approval No. QA010
* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.
A, B, D, E 50 Normal Strength Sections NIPPON STEEL CORPORATION Kobe
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
1, Chikko Yawata-cho Sakai-Ku
Sakai city
Sakai Works
Tel: +81 722 33 1179 Fax: +81 722 33 1185 Email mailto:matsukura@nihon-steel.co.jp
Osaka
As below E.A.F. / Con Cast Steelmaking Nippon Metal Industry Co., Ltd. Kobe
304L, 316L, 321, 347 8 Austenitic Stainless Strip
Hekinan-shi
Aichi- ken
Kinuura Works
1, Hama-cho
Tel: +81 566 48 7218 Fax: +81 566 48 1596 Email: mailto:nishimuraK@nikkinko.co.jp
447-8610
As at 19 March 2007 29 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Con Cast Steelmaking OJI STEEL CO., LTD. Yokohama
A 25 Normal Strength Bars
AH32, AH36 25 Higher Strength
Ota-city
Gunma Pref.
Gunma Works
120, Nittasorimachi-cho
Tel: +81 276 56 2119 Fax: +81 276 56 3136 Email: mailto:n-komuro@oji-steel.co.jp
370-0313
A E.A.F. / Con Cast Steelmaking OSAKA STEEL CO., LTD. Kobe
1 Chikko Yawata-cho
Sakai
Sakai Works
Tel +81 722 33 3901 Fax +81 722 33 3976
Osaka
As below E.A.F. / Con Cast Steelmaking OSAKA STEEL CO., LTD. Kobe
A, B, D 15 Normal Strength Sections
AH32, AH36 12 Higher Strength
9-3 Minami Okajima 1 Chome
Taisho-ku
Okajima Works
Tel: +81 06 6552 1447 Fax: +81 06 6552 3184 Email: mailto:yo-okada@osaka-seitetsu.co.jp
As below E.A.F. / Con Cast Steelmaking SHINKANSAI STEEL CORPORATION Kobe
A, B, D, E 38 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36 38 Higher Strength
A, B, D 130 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36 130 Higher Strength
5, Shiohama-cho
Sakai
Sakai Works
Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:hasegawa@shinkansai-steel.co.jp Web: http://www.shinkansai-steel.co.jp
As below E.A.F. / Con Cast Steelmaking SHINKANSAI STEEL CORPORATION Kobe
A 80 Normal Strength Bars
U1, U2, U3 80 Chain Cable Stock
4-26-1, Hoshida Kita
Katano-shi
Hoshida Works
Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319 Email mailto:okayama@shinkansai-steel.co.jp Web http://www.shikansai-steel.co.jp
austenitic stainless A.O.D./Con Cast Steelmaking SUMITOMO METAL INDUSTRIES, LTD. Yokohama
carbon, carbon-manganese, alloy B.O.S./Ingot/Con Cast
A, B, D, E 150 Normal Strength Plates
FH27S, FH32, FH36 32 Higher Strength
AH42, AH46, AH50, AH55, AH62, DH42, DH46,
DH50, DH55, DH62
47
AH36S, AH40S, DH36S, DH40S, EH36S, EH40S 50
AH36, AH40, DH36, DH40, EH27S, EH32, EH36,
EH40
105
AH27S, AH32, DH27S, DH32 150
360AR, 410AR, 460AR 40 Boiler & Pressure Vessel
510FG 55
360, 410, 460, 490 63
360FG, 410FG, 460FG, 490FG 100
3.5Ni, 5Ni 30 Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
45
EH36/304L, EH36/316L 38 Clad
EH27S, EH32, EH36 32 Differential Thickness
A,B,D, AH27S, AH32, AH36, DH27S, DH32,
DH36
35
A, B, D 19 Normal Strength Strip
360, 410, 360FG, 410FG 19 Boiler & Pressure Vessel
A, B, D, E 35 Normal Strength Sections
AH40, DH40, EH27S, EH32, EH36 18 Higher Strength
DH27S, DH32, DH36 20
AH27S, AH32, AH36 35
As at 19 March 2007 30 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Kashima City
Ibaraki Pref.
Kashima Steel Works
3 Hikari
Tel +81 (0)299 84 2575 Fax +81 299 84 2945
All plates with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 002
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested in
accordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not imply
concessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC condition
up to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on either
design or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM
+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does not
imply concessions on either design or survey requirements.
(Note CRL = Corrosion Ratio by Long term test)
314-0014
A 240 Normal Strength Bars SUMITOMO METAL INDUSTRIES, LTD. Kobe
1, Nishino-cho
Higashi-Mukojima
Steel Tube Works
Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:furubaya-hdy@sumitomometals.co.jp
Amagasaki, 660-0856
carbon, carbon-manganese, alloy B.O.S. / Con Cast Steelmaking SUMITOMO METAL INDUSTRIES, LTD. Kobe
austenitic stainless A.O.D./Con Cast
1850 Minato
Wakayama-city
Pipe & Tube Works
Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103 EMail: mailto:kondou-tmo@sumitomometals.co Sales fax +81 34416 6789 Web: www.sumitomometals.co.jp
640-8555
As below E.A.F. / Ingot Steelmaking SUMITOMO METALS (NAOETSU), LTD. Yokohama
304L, 316L, 321, 347 25 Austenitic Stainless Plates
Joetsu-shi
Niigata
2-12-1, Minato-cho
Tel: +81 25 544 6622 Fax: +81 25 544 6642 Email mailto:kamidairator@sumitomometals.co.jp Web: http://www.sumitomometals.co.jp
942-8510
A B.O.S. / Con Cast Steelmaking SUMITOMO METALS KOKURA Nagasaki
A 30 Normal Strength Sections
A 220 Normal Strength Bars
R4 85 Chain Cable Stock
U1, U2, U3, API-2F 100
Kokura Kita-ku
Kitakyushu City
Production & Technology Division
1, Konomi-machi
Tel: +81 93 5618093 Fax: +81 93 5913930 EMail mailto:ishimoto-nbo@sumitomometals.co.jp
Fukuoka Pref.
As below E.A.F. / Ingot Steelmaking Sanyo Special Steel Co., Ltd. Kobe
A 220 Normal Strength Bars
Shikama-ku
Himeji-shi
3007 Nakashima
Tel: +81 (0)792 35 6029 Fax: +81 (0)792 34 5033 Web: http://www.sanyo-steel.co.jp
672-8677
As below E.A.F. / Ingot Steelmaking THE JAPAN STEEL WORKS LTD. Yokohama
A, B, D, E 50 Normal Strength Plates
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
304L, 316L 65 Austenitic Stainless
AH32/304L, AH32/316L, AH32/316LN,
AH32/317L
19 Clad
AH32/S31803 30
A/304L, B/304L, D/304L, E/304L, A/316L,
B/316L, D/316L, E/316L
100
As at 19 March 2007 31 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Muroran
Hokkaido
Muroran Plant
4, Chatsu-machi
Tel +81 (0)143 22 0451 Fax +81 (0)143 22 5736 Email: mailto:kenji_tanaka@jsw.co.jp
051-8505
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking TOKAI SPECIAL STEEL CO., LTD. Kobe
Tokai-Machi
Tokai-shi
3, 5-Chome
Tel +81 52 603 7225 Fax +81 52 603 7229 EMail mailto:okayama@nagoya.nsc.co.jp
Aichi-ken
As below E.A.F. / Con Cast Steelmaking TOKYO STEEL MANUFACTURING CO., LTD. Nagasaki
A 32 Normal Strength Plates
360AR, 410AR 32 Boiler & Pressure Vessel
A 24 Normal Strength Sections
Wakamatsu-ku
Kitakyusyu City
Kyushu Plant
3-5-1, Minami-Futajima
Tel: +81 93 701 2631 Fax: 81 93 791 2631 Email: mailto:moriwaki@tokyosteel.co.jp Web http://www.tokyosteel.co.jp
Fukuoka
As below E.A.F. / Con Cast Steelmaking TOKYO STEEL MANUFACTURING CO., LTD. Kobe
A 12 Normal Strength Sections
4-1-1, Minamise
Kurashiki City
Okayama Plant
Tel: +81 86 455 7182 Fax: +81 86 455 6434
Okayama Pref.
As below E.A.F. / Con Cast Steelmaking TOPY INDUSTRIES, LTD. Kobe
E 20 Normal Strength Sections
A, B, D 35
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
20 Higher Strength
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
20 Ferritic Low Temperature
A, B, D, E 50 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
1, Akemi-cho
Toyohashi-shi
Toyohashi Works
Tel +81 532 25 1111 Fax +81 532 25 7045 Email: mailto:s-hashimoto@topy.co.jp
Aichi-ken
As below E.A.F. / Con Cast Steelmaking YAKIN Kawasaki Co., Ltd. Yokohama
321, 347 10 Austenitic Stainless Plates
304L, 316L 53
Fe-36Ni* 8 Fe-Ni alloys
304L, 316L, 321, 347 8 Austenitic Stainless Strip
Fe-36Ni* 3 Fe-Ni alloys
Kawasaki-ku
Kawasaki-shi
4-2, Kojima-cho
Tel: +81 44 271 3130 Fax: +81 44 271 3292 Email mailto:kawashita@nyk.co.jp Internet http//www.nyk.co.jp
* accepted for approved applications
210-8558
As below E.A.F. / Con Cast Steelmaking YAMATO STEEL CO., LTD. Kobe
A, B, D 25 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36 25 Higher Strength
380, Kibi, Ohtsu-ku
Himeji City
Tel: +81 (0)792 73 0716 Fax: +81 (0)792 74 2692 Web:http://www.yamatokogyo.co.jp
Hyogo-pref.
As at 19 March 2007 32 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Korea
carbon-manganese E.A.F. / Con Cast Steelmaking DONGKUK STEEL MILL Co. Ltd. Ulsan
carbon-manganese 480 Blooms/Billets Semi-Finished
D, E 50 Normal Strength Plates
A, B 83
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36, FH27S, FH32, FH36
50 Higher Strength
360FG, 410FG, 460FG, 490FG 25 Boiler & Pressure Vessel
360AR, 410AR 40
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
50 Ferritic Low Temperature
D 25 Normal Strength Sections
A, B 32
AH27S, DH32 25 Higher Strength
AH32, DH27S 32
880 Songdong-Ri
Daesong-Myun, Nam-Gu
Pohang Works
Tel: +82 562 271 2683 Fax: +82 562 271 5317 EMail: sckim@dongkuk.co.kr Web page http://www.dongkuksteel.com
Pohang City, Kyungsangbuk-Do
304L, 304LN, 316L, 316LN 80 Austenitic Stainless Plates Dae Kyung Corp. Seoul
UNS S31803, UNS 32900*, UNS 32205* 50 Duplex Stainless
#612-1, Go Hyun Ri
Chung Ha Myun
Tel: +82 54 232 3823 Fax: +82 54 232 4161 Email:mailto:skypass@dae-kyung.co.kr Web:http://www.dae-kyung.co.kr
Buk-Ku, Pohang City
A 15 Normal Strength Sections FINE STEEL CO., LTD. Busan Port
230-4 Hakjang-Dong
Sasang-Ku
Tel: +82 (0)51 313 2881 Fax: +82 (0)51 325 6378 Web:http://www.fine-steel.com
Busan
As below E.A.F. / Con Cast Steelmaking HYUNDAI STEEL COMPANY Seoul
A, B 32 Normal Strength Sections
AH27S, AH32, AH36 32 Higher Strength
#1, Songhyun-Dong
Dong-Ku
Inchon Plant
Tel: +82 32 760 2755 Fax: +82 32 760 2866
Sections include flat bars up to 400 mm width.
Inchon
As below E.A.F. / Con Cast Steelmaking HYUNDAI STEEL COMPANY Ulsan
carbon, carbon-manganese, alloy Blooms/Billets Semi-Finished
B, D, E 18 Normal Strength Sections
A 28
AH27S, AH32, AH36 18 Higher Strength
R3S, R4 110 Chain Cable Stock Bars
U1, U2, U3, R3 150
444 Songnae-Dong
Nam-Gu
Pohang Plant No. 1
Tel: +82 54 271 1472 Fax: +82 54 271 1512 Email: mailto:limnk@inisteel.com Web: http://www.inisteel.com
Pohang
carbon-manganese E.A.F. / Con Cast Steelmaking HYUNDAI STEEL COMPANY Ulsan
A, B, D 12 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
12 Higher Strength
1857 Jangheung-Dong
Pohang Plant No. 2
Web: http://www.inisteel.com
As below E.A.F. / Ingot Steelmaking KOREA IRON & STEEL CO., LTD. Busan Port
carbon, carbon-manganese, alloy 8 Ingots Semi-Finished
carbon, carbon-manganese, alloy Blooms/Billets
N 70, Shinchon-dong
Changwon
Tel +82 55 260 0744 Fax +82 55 282 4123 Email mailto:shim0744@kisco.co.kr Web page http://www.kisco.co.kr
Including steelmaking
Kyungnam
As at 19 March 2007 33 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 19 Normal Strength Sections Korea Steel Shapes Co., Ltd. Busan Port
A 38 Normal Strength Bars
727-3 Hakjang-Dong
Sasang-Ku
Sasang Works
Tel: 051 323 2611 Fax: 051 325 3391
Busan
A 15 Normal Strength Sections Korea Steel Shapes Co., Ltd. Busan Port
A 65 Normal Strength Bars
1660-1 Songjeong-Dong
Gangseo-Ku
Noksan Works
Tel: 051 831 6811 Fax: 051 831 3957
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking POSCO Gwangyang Works Changwon
carbon, carbon-manganese 300 Slabs Semi-Finished
A, B, D 22 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36 12 Higher Strength
460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
360FG, 410FG 22
700 Kumho-dong
Kwangyang-si
Tel: +82 61 790 2923 Fax: +82 61 790 2909 Email: mailto:kms0724@posco.co.kr
Cheonnam 545-711
As Below B.O.S./E.A.F./Con Cast Steelmaking POSCO Pohang Works Ulsan
A, B, D, E 90 Normal Strength Plates
FH27S, FH32, FH36 83 Higher Strength
AH40, DH40, EH40 90
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 90
LTAH27S, LTAH32, LTAH36, LTDH27S,
LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,
LTFH27S, LTFH32, LTFH36
50 Ferritic Low Temperature
304L, 304LN, 316L, 316LN 80 Austenitic Stainless
UNS S31803, UNS 32900*, UNS 32205* 50 Duplex Stainless
E 12 Normal Strength Strip
A, B, D 22
EH27S, EH32, EH36 16 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36 22
460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
360FG, 410FG 22
304L, 316L 8 Austenitic Stainless
5, Dongcheon-Dong
Nam-ku, Pohang City,
Tel: +82 54 220 4832 Fax: +82 54 220 1299 Email: mailto:wkj09@posco.co.kr Web: http://www.posco.co.kr/posco-in
All plates with through thickness properties.
*approved applications
Kyungsangbuk-Do
As below E.A.F. / Ingot Steelmaking POSCO SPECIALITY STEEL CO., LTD. Changwon
carbon, carbon-manganese, alloy 150 Structural Bars
austenitic stainless 170
carbon, carbon-manganese, alloy 150 Machinery
Changwon
Kyungnam
65, Shinchon-dong
Tel: +82 (0)55 269 6727 Fax: +82 (0)55 269 6910 Emal:mailto:ladylady@cssteel.co.kr Web: http://www.changwonsteel.co.kr
Including ingots for forging up to 100 tonne
641-370
carbon, carbon-manganese, alloy E.A.F./Ingot/Con Cast Steelmaking SeAH BESTEEL CORPORATION Seoul
R4 155 Chain Cable Stock Bars
U1, U2, U3, R3, R3S 165
carbon, carbon-manganese, alloy 190 Machinery
Kunsan-Si
Jeollabuk-Do 573-711
Kunsan Works
1-6, Soryong-Dong
Tel: +82 63 460 8606 Fax: +82 63 460 8423 Email: mailto:knr1031@seahbesteel.co.kr Web:http://www.kss.co.kr
As below B.O.S. / Con Cast Steelmaking YK STEEL CORP. Busan Port
A 7 Normal Strength Sections
A 32 Normal Strength Bars
604-817, Pusan
90 Gupyung-Dong
Saha-Gu
Tel. +82 (0)51 260 2441 Fax +82 (0)51 265 2167 Email:mailto:mspark@yk-steel.co.kr Web: http://www.yk-steel.co.kr
As at 19 March 2007 34 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Latvia
A 15 Normal Strength Fabricated Sections ASK Enterprise Riga
AH32 15 Higher Strength
Riga LV-1015
2 Str. Gales
Tel: +371 7353 373 Fax: +371 7353 050
Luxembourg
As below E.A.F. / Con Cast Steelmaking ARCELOR PROFIL LUXEMBOURG S.A. Lyon
B, D 12 Normal Strength Sections
A 40
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
25 Higher Strength
66 rue de Luxembourg
L 4009 Esch sur Alzette
ESCH-BELVAL MILL
Tel: +352 58 2884 Fax: +352 5835 81 Contact: Mr Muller Email: mailto:julien.bettendorff@arcelor.com
As below E.A.F./Ingot/Con Cast Steelmaking ARCELOR PROFIL LUXEMBOURG S.A. Lyon
A, B 40 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
Division Differdange
Tel: +352 58 2028 75 Fax: +352 5835 81 Contact: Mr Muller Email: mailto:gaetan.muller.@arcelor.com
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking ARES SA Lyon
A, B, D 30 Normal Strength Sections
AH36, DH36 30 Higher Strength
carbon, carbon-manganese 125 Semi-finished Products Bars
BP24
L-4801 Rodange
ARCELOR GROUP
Tel: +352 5019 2366 Fax: +352 5019 2217 Email: mailto:nicolas.matinussen@areclor.com
A 40 Normal Strength Sections TLM (Train Lamin Marchand) Lyon
A 40 Normal Strength Bars
L-4241 Esch Sur Alzette
Boulevard Aloyse Meyer
Tel: +352 57 129 33 31 Fax: +352 57 129 21 26 Email: mailto:m.tonon@lme.fr
Macedonia
As below E.A.F. / Con Cast Steelmaking A. D. MAKSTEEL Beograd
E 50 Normal Strength Plates
A, B, D 100
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH32, EH36
50 Higher Strength
360AR, 410AR, 460AR 40 Boiler & Pressure Vessel
360, 410, 460, 490, 460FG, 490FG, 510FG 50
360FG, 410FG 100
XVI Makedonska brigada 18
P.O. Box 599
Tel: +389 2 328 7024 Fax: +389 2 328 7032 Email mailto:kocovski@makstil.com.mk Web http://www.makstil.com.mk
Specified through thickness properties for plates up to 50 mm thickness
1000 Skopje
A 45 Normal Strength Fabricated Sections D S CONSTRUCTION LTD. Beograd
Kumanovo
11 Oktomvri, street no. 89
Tel: +389 31 439 700 Fax: +389 31 439 702 email: mailto:sales@dsiskra.com.mk Web: http://www.dsiskra.com.mk
Approved for the following welding parameters:
Weld joint type: Fillet only
Maximum weld size: 15 mm fillet leg
Welding process: Submerged Arc Welding
Joint Type: Fillet weldfillet welded sections only (maximum fillet weld size = 15 mm).
A 35 Normal Strength Fabricated Sections FAKOM ENGINEERING D.O.O.E.L.-SKOPJE Beograd
POB 439
1000 SKOPJE
St. Aleksander Makedonski No.5
Telephone: +389 (0)2 3174 023, Fax: +389 (0)2 3173 564
email: mailto:fakom@mt.net.mk Web http://www.fakom.com.mk Telex 51517 Fakom
As at 19 March 2007 35 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Malaysia
A 30 Normal Strength Plates JI KANG DIMENSI Sdn. Bhd. Kuala Lumpur
26100 Kuantan
Pahang Darul Makmur
Lot 69-71, Kawasan Perindustrian Gebeng
Tel: +60 (0)129481122/095839881 Fax: +60 (0)9583 9881/095839882 Email: mailto:hayashiilim@yahoo.com
A 38 Normal Strength Plates Lion Plate Mills Sdn Bhd Kuala Lumpur
24007 Kemaman
Terrengganu
Lot 3916, Teluk Kalong Industrial Estate
As below E.A.F. / Con Cast Steelmaking Megasteel Sdn. Bhd. Kuala Lumpur
A, B, D, E 16 Normal Strength Strip
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
12 Higher Strength
460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
360FG, 410FG 16
Mukim Tanjung Dua Belas
42700 Banting
Lot 2319, Kawasan Perindustrian Olak Lempit
Tel: +60 (0)3 3181 6666 Fax: +60 (0)3 3181 6929
Selangor Darul Ehsan
Mexico
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking MITTAL STEEL,LAZARO CARDENAS, S.A. DE C.V. Metepec/Veracr
uz
carbon, carbon-manganese 250 Slabs Semi-Finished
60950- Lzaro Crdenas
Michoacan
Av Francisco J. Mujica N 1-B
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperature
service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for
ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
Tel: +52 753 533 2528 Fax: +52 753 532 2562 Email: mailto:rafael.mendoza@mittalsteel.com Web http://www.mittalsteel.com
Netherlands
As below B.O.S. / Con Cast Steelmaking CORUS STAAL B.V. Amsterdam
A, B 20 Normal Strength Plates
A, B 20 Normal Strength Strip
Postbus 10000
1970 CA Ijmuiden
Ijmuiden Works
Tel +31 2514 92110 Fax +31 2514 70414 Email: mailto:marc.van-der-velde@corusgroup.com
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking NEDSTAAL STAAL B.V. Rotterdam
Marine
carbon, carbon-manganese, alloy 11 Ingots Semi-Finished
carbon, carbon-manganese, alloy 320 Slabs
carbon, carbon-manganese, alloy 400 Blooms
carbon, carbon-manganese, alloy 125 Billets
Rapenburg 1
P.O. Box 210
Tel: +33 (0)78 692 3715 Fax: +31 (0)78 692 3712 Email mailto:anton.rombout@nedstaal.nl Web http://www.nedstaal.nl
2950 AE Alblasserdam
As at 19 March 2007 36 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Norway
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking FUNDIA ARMERINGSSTL AS Oslo
PO Box 500
NO-8601 Mo i Rana
Mo Industripark
Tel: +47 7513 6500 Fax: +47 7513 6845 Email: mailto:snorre.petersen@rukki.com Web http://www.ruukki.com
A, B, D, E 50 Normal Strength Sections RUUKKI PROFILER AS Oslo
FH32, FH36, DH46, EH46 35 Higher Strength
AH32, AH36, AH40, DH32, DH36, DH40, EH32,
EH36, EH40, DH42, EH42
50
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36
35 Ferritic Low Temperature
A, B, D, E 35 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32, EH36 35 Higher Strength
P.O. Box 500
NO-8601 Mo I Rana
Tel: +47 75 13 64 00 Fax: +47 75 13 68 04 Email: mailto:profiler@ruukki.com Web http://www.ruukki.com
Peru
As below B.O.S. / Ingot Steelmaking EMPRESA SIDERURGICA DEL PERU S.A.A. Callao
As below E.A.F. / Ingot
A 32 Normal Strength Plates
360AR, 410AR 32 Boiler & Pressure Vessel
A 10 Normal Strength Strip
360, 410 10 Boiler & Pressure Vessel
Chimbote
Av. Santiago Antunez de Mayolo s/n
Tel +51 43 883000 Fax +51 43 324580 Email: mailto:jwillstatter@sider.com.pe
Poland
A, B, D, E 25 Normal Strength Plates ''HUTA POKJ'' S.A. Katowice
360AR, 410AR, 360, 410, 360FG, 410FG 25 Boiler & Pressure Vessel
A, B, D, E 25 Normal Strength Sections
ul. Niedurnego 79
41-709 Ruda Slaska
Tel +48 32 772 1668 Fax +48 32 772 4332 Email: akarbownik@hutapokoj.com.pl
As below E.A.F. / Ingot Steelmaking ARCELOR HUTA WARSZAWA Sp. z.o.o. Katowice
As below E.A.F./Ingot/Con Cast
carbon, carbon-manganese, alloy 150 Structural Bars
U1, U2, U3 150 Chain Cable Stock
carbon, carbon-manganese, alloy 65 Machinery
ul. Kasprowicza 132
01-949 Warszawa
Tel: +48 22 835 8050 Fax: +48 22 834 0952
Email: mailto:beata.pietrzyk@hw.arcelor.com Web: http://www.arcelor-hutawarszawa.pl
As below E.A.F./Ingot/Con Cast Steelmaking CELSA "HUTA OSTROWIEC" Sp. z o.o. Katowice
carbon, carbon-manganese, alloy 150 Ingots Semi-Finished
A, B, D, E, AH27S, AH32, AH36, AH36, DH27S,
DH32, DH36, EH27S, EH32, EH36, carbon,
carbon-manganese, alloy
320 Blooms
A, B, D, E, AH27S, AH32, AH36, DH27S, DH32,
DH36, EH27S, EH32, EH36, carbon,
carbon-manganese, alloy
120 Billets
ul. Samsonowicza 2
27-400 Ostrowiec Swietokrzyski
Tel: +48 (0)41 2492857 Fax: +48 (0)41 2493240 EMail mailto:mdymara@celsaho.com Web page http://www.gcelsa.com
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking CMC Zawiercie S.A. Katowice
A, B, D 52 Normal Strength Bars
U1, U2, U3 52 Chain Cable Stock
ul. Pilsudskiego 82
42-400 Zawiercie
Tel: +48 32 67 253 01 Fax: +48 32 67 253 18 Email: mzalawa@cmcpoland.com
A 40 Normal Strength Fabricated Sections ENERGOMONTAZ-POLNOC GDYNIA Sp. z o.o. Gdansk
AH32, AH36 40 Higher Strength
81-038 Gdynia
ul.Handlowa 19
Tel: +48 58 667 32 81 Fax: 48 58 623 71 18 Email: mailto:energomontaz@energomontaz.gdynia.pl Web: http://www.energomontaz.gdynia.pl
As at 19 March 2007 37 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking FERROSTAL ABEDY Sp. z.o.o. Katowice
carbon, carbon-manganese, alloy 160 Blooms/Billets Semi-Finished
ul. Zawadzkiego 26
44-109 Gliwice
Tel: +48 32 234 7600 Fax: +48 32 234 7650 EMail mailto:biuro@ferrostal.com.pl Web page http://www.ferrostal.com.pl
As below E.A.F./Ingot/Con Cast Steelmaking HSW - HUTA STALI JAKOSCIOWYCH SA Katowice
A, B, D, E 120 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
120 Higher Strength
carbon, carbon-manganese, alloy 120 Structural
U1, U2, U3 110 Chain Cable Stock
carbon, carbon-manganese, alloy 120 Semi-finished Products
carbon, carbon-manganese, alloy 120 Machinery
ul. Kwiatkowskiego 1
37-450 Stalowa Wola
Tel: +48 15 843 59 06 Fax: +48 15 844 23 06 Email: mailto:handlowy@hsw-hsj.com.pl Web: http://www.hsw-hsj.com.pl
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Ingot Steelmaking HUTA BATORY Sp. z o.o. Katowice
ul.Dyrekcyjna 6
41-506 Chorzw
Tel: +48 32 77 22 782 Fax:+48 32 77 22 867 Email:mailto:hbhandel@hutabatory.com.pl Web: http://www.hutabatory.com.pl
A 25 Normal Strength Sections HUTA KRLEWSKA Sp. zo.o Katowice
A 65 Normal Strength Bars
U1, U2, U3 48 Chain Cable Stock
ul. Metalowcw 13
41-500 Chorzw
Tel. 048 32 241 18 38 Fax 048 32 241 18 38
email: mailto:marketing@hutakrolewska.pl web: www.hutakrolewska.pl
A 20 Normal Strength Sections Huta Bankowa Sp. z o.o. Katowice
AH27S, AH32, AH36, DH27S, DH32, DH36 20 Higher Strength
A 250 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36 20 Higher Strength
U1, U2 160 Chain Cable Stock
ul. Sobieskiego 24
41-300 Dbrowa Grnicza
Tel +48 32 295 7610 Fax +48 32 262 5249 Email: bhim@hutabankowa.com.pl
A, B, D, E 100 Normal Strength Plates Huta Katowice Walcownia Katowice
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
A/304L 50 Clad
41-506 Chorzw
Blach Grubych BATORY Sp. z.o.o.
ul. Dyrekcyjna 6
Tel; +48 32 7722525 Fax: +48 32 7722575 Email mailto:marketing@blachy-batory.pl Web http://www.blachy-batory.pl
All plates with specified through thickness properties
As below E.A.F. / Con Cast Steelmaking ISD HUTA CZESTOCHOWA sp. z o.o. Katowice
As below O H / Con Cast
A, B, D, E 50 Normal Strength Plates
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,
490FG, 510FG
50 Boiler & Pressure Vessel
42-207 Czestochowa
Zakad Rurexpol
ul. Kucelinska 22
Tel: +48 34 323 8167 Fax: +48 34 323 1271 Email: maito:uwasiak@hcz.com.pl Web: http://www.hcz.com.pl
As below B.O.S. / Con Cast Steelmaking MITTAL STEEL POLAND S.A. Katowice
A, B, D 12 Normal Strength Plates
AH27S, AH32, DH27S, DH32 12 Higher Strength
360AR, 410AR, 360FG, 410FG 12 Boiler & Pressure Vessel
A, B, D 6 Normal Strength Strip
360FG, 410FG 6 Boiler & Pressure Vessel
30-969 Krakw
Oddzia w Krakowie
ul. Ujastek 1
Tel +48 32 731 61 68 Fax +48 32 731 62 41 EMail mailto:jozef.gawlicki@ipssa.pl Web page http://www.ipssa.pl
carbon, carbon-manganese B.O.S./Ingot/Con Cast Steelmaking MITTAL STEEL POLAND S.A. Katowice
carbon, carbon-manganese 250 Slabs Semi-Finished
carbon, carbon-manganese 280 Blooms/Billets
B, D, E 15 Normal Strength Sections
A 20
A 200 Normal Strength Bars
As at 19 March 2007 38 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
41-308 Dbrowa Grnicza
Oddzia w Dbrowie Grniczej
Al. Pisudskiego 92
Tel: +48 32 795 5103 Fax: +48 32 5250 Email mailto:marketing@ipssa.pl Web: http://www.mittal-steel.pl
Approved for ingots, and continuously cast products for re- rolling in all the normal and higher tensile strength grades.
A, B, D, E 40 Normal Strength Sections P.H.U.P. ''INTERSPEED'' Sp. zo.o Katowice
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH32, EH36, FH27S
40 Higher Strength
A 40 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
ul. Gulinskiego 26
27-400 Ostrowiec Swietokrzyski
Tel: +48 (0)41 247 1679 Fax: +48 (0)41 247 4602 Email: mailto:handel@interspeed.com.pl Web page http://www.interspeed.com.pl
A, B 20 Normal Strength Sections ZW - WALCOWNIA BRUZDOWA Sp. z o. o. Katowice
AH27S, AH32, AH36 20 Higher Strength
Ul.Oklna 10
42-400 Zawiercie
Rolling Mill Works
Tel: +48 32 671 00 10/11/13/14 Fax:+48 32 671 00 201 Email mailto:walcowniabruzdowa@cn.com.pl
Romania
As below E.A.F. / Ingot Steelmaking MECHEL TARGOVISTE S.A. Galatz
carbon, carbon-manganese, alloy Blooms/Billets Semi-Finished
U1, U2, U3 95 Chain Cable Stock Bars
Sos. Gaiesti, 9-11
Jud Dambovita, 130087
Targoviste
Tel: +40 245 632907 Fax: +40 245 213322 Email: mailto:dumitru@cost.ro Web: http://www.mechel.com
As below B.O.S. / Con Cast Steelmaking MITTAL STEEL GALATI S.A. Galatz
As below B.O.S. / Ingot
A, B, D, E 100 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
100 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
800698 Galati
Sos. Smardan Nr.1
Plates with specified through thickness properties in all grades up to 60 mm thickness in the normalized condition
Tel: +40 236 411900 Fax: +40 236 409322 Email: mailto:i.ivan@sidex.ro Web page http://www.mittalsteel.com
As below E.A.F./Ingot/Con Cast Steelmaking MITTAL STEEL HUNEDOARA, S.A. Galatz
carbon, carbon-manganese, alloy 270 Blooms/Billets Semi-Finished
A, B, D 16 Normal Strength Sections
A, B, D 16 Normal Strength Bars
Piata Iancu de Hunedoara Nr. 1
331031 Hunedoara
Tel +40 254 713545 Fax +40 254 713545 Email: mailto:gabriela.popescu@mittalsteel.com Internet http://www.mittalsteel.com
carbon, carbon-manganese E.A.F. / Ingot Steelmaking S.C. Industria Sarmei S.A. Galatz
145 Laminoristilor st.
3351 Campia Turzii
Tel: +40 264 365187 Fax: +40 264 365187 Email: mailto:technic@isct.ro
Cluj - Napoca
A 50 Normal Strength Sections S.C. LAMINORUL S.A. - BRAILA Galatz
A 50 Normal Strength Bars
810461 Braila
Sos. Industria Sarmei nr. 2
Tel +40 239 681830 Fax +40 239 669387 Email: mailto:secretariat@laminorul.ro
As at 19 March 2007 39 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Russia
AH32, DH32, EH32 40 Higher Strength Fabricated Sections CHELYABINSK STEEL STRUCTURES PLANT Moscow
Chelyabinsk
454139
46, Novorossiyskaya Str.,
Tel: +007 (3512)532821 Fax +007 (3512)537789 EMail: mailto:galen@metcon.ru Web http://www.metcon.ru
As Below B.O.S./E.A.F./Ingot/Con Cast Steelmaking J.S.C. Severstal St. Petersburg
A, B, D, E 40 Normal Strength Plates
EH27S, EH32 32 Higher Strength
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH40
40
360, 410 32 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 40
30 Mira Str
162 600 Cherepovets
Rolling Mill 2800
All plates with specified through thickness properties.
Tel: +7 8202 531489/11 20 Fax: +7 8202 532626 EMail: mailto:sales@stal.ru Web http://www.severstal.ru
Vologoda Region
As Below B.O.S./E.A.F./Con Cast Steelmaking J.S.C. Severstal St. Petersburg
A, B, D, E 12 Normal Strength Strip
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
12 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 12 Boiler & Pressure Vessel
162600 Cherepovets
Rolling Mill 2000
Tel: +7 8202 531489/11 20 Fax: +7 8202 532626 EMail: mailto:sales@stal.ru Web http://www.severstal.ru
As Below B.O.S./E.A.F./Con Cast Steelmaking J.S.C. Severstal St. Petersburg
D, E 50 Normal Strength Plates
A, B 70
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
70 Higher Strength
Saint Petersburg
Rolling Mill 5000
Kolpino
Tel: +7 8202 561146 Fax: +7 8202 571276 EMail: mailto:severstal@stal.ru
Plates with specified through thickness properties
As below O H / Ingot Steelmaking JSC KIROVSKIY ZAVOD St. Petersburg
carbon, carbon-manganese 120 Semi-finished Products Bars
47 Stachek Prospect
198097 St. Petersburg
Petrostal Steel Works
Tel: +7 812 702 0240 Fax: +7 812 702 0261 Email mailto:bvf@petrostal.spb.ru Web: http://www.petrostal.spb.ru
As below B.O.S. / Con Cast Steelmaking JSC Magnitogorsk Iron & Steel Works St. Petersburg
A 50 Normal Strength Plates
A 10 Normal Strength Strip
360FG, 410FG 10 Boiler & Pressure Vessel
455002 Magnitogorsk
93, Kirova Street
Tel +007 3519 24 40 09 Fax +007 3519 24 73 09 Web http://www.mmk.ru
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking MECHEL OAO St. Petersburg
carbon, carbon-manganese, alloy 20 Ingots Semi-Finished
2-d Paveletskaya ul, 14
CHELYABINSK METALLURGICAL PLANT OAO
454047- Chelyabinsk
Tel; +7 351 725 30 24 Fax: +7 351 722 86 29 Email mailto:sale@mechel.ru
Head Office Mechel OAO , 123610, Moscow. Krasnopresnenskaya Naberezhnaya, 12, Office 1002 Russia
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking NIZHNY TAGIL METALLURGICAL KOMBINAT St. Petersburg
1, Metallurgov Str.,
Nizhny Tagil,
Continuously cast slabs suitable for rolling to Lloyd's Register ship grade normal and higher tensile strength steel plates up to and including grade EH36
Tel:+7 3435 490597/490611 Fax:+7 3435 490694/496169 Email:mailto:ashihin@ntmk.tagil.ru Web http://www.ntmk.ru
Sverdlovsk Region, 622025
As below B.O.S. / Con Cast Steelmaking Novolipetsk Iron & Steel Corporation Moscow
A, B, D, E 16 Normal Strength Strip
EH32 10 Higher Strength
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH36, EH40
12
460FG, 490FG 10 Boiler & Pressure Vessel
360, 410, 360FG, 410FG 16
As at 19 March 2007 40 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Pl. Metallurgov 2, NLMK
Lipetsk
398040, Russia
Tel: +7 0742 444688 Fax: +7 0742 444688 Email:mailto:info@nmlk.ru Web:http://www.nlmk.ru Telex: 412630NLMK RU
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking OSKOL St. Petersburg
carbon, carbon-manganese 360 Blooms Semi-Finished
U1, U2, U3 80 Chain Cable Stock Bars
Belgorod Region
ELECTROMETALLURGICAL KOMBINAT
309515 Stary Oskol-15
Tel +0725 37-5310 Fax +0725 32-9429
A, B, D 14 Normal Strength Sections TURBINE BLADES PLANT AT ST PETERSBURG St. Petersburg
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36
14 Higher Strength
Branch of OJSC ''Power Machines -ZTL, LMZ, Elektro
Energomashexport''
Tel: +7 (812) 567 57 58 Fax: +7 (812) 568 06 03 Email: mailto:market@ztl.ru Web http//www.ztl.ru
As below O H / Ingot Steelmaking URAL STEEL Open Joint-Stock Company St. Petersburg
As below E.A.F./Ingot/Con Cast
B, D 40 Normal Strength Plates
A 50
AH32, AH36 40 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 40 Boiler & Pressure Vessel
Novotroitsk
Orenburg Region
1, Zavodskaya Street
Tel: +7 3537 66 20 89 Fax: +7 3537 66 27 89 Email: mailto:info@uralsteel.com Web: http://www.uralsteel.com
462353
Serbia & Montenegro
A, B, D 15 Normal Strength Plates U.S. STEEL SERBIA d.o.o. Beograd
360AR, 410AR 15 Boiler & Pressure Vessel
Goranska 12
11300 Smederevo
Tel: +381 26 224 428 Fax: +381 26 225 260 Contact: Martin Tucek email: martintucek@usske.sk
Slovak Republic
A, B, D, E, AH32, AH36, DH32, DH36, EH32,
EH36
B.O.S. / Con Cast Steelmaking U.S. Steel Kosice, s.r.o. Prague
A, B, D 12 Normal Strength Plates
360AR, 410AR, 360FG, 410FG 12 Boiler & Pressure Vessel
A, B, D 12 Normal Strength Strip
360, 410, 360FG, 410FG 12 Boiler & Pressure Vessel
Vstupny areal U.S. Steel
044 54 Kosice
Tel: +421 55 673 3409 Fax: +421 55 673 0730 Email: mailto:vrac@sk.uss.com Web: http:www.usske.sk
Slovenia
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking ACRONI, d.o.o. Zagreb
austenitic stainless E.A.F./V.O.D./Con Cast
A, B, D, E 40 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
360AR, 410AR, 360, 410, 360FG, 410FG, 460FG,
490FG, 510FG
40 Boiler & Pressure Vessel
304L, 316L, 317L, 321, 347 70 Austenitic Stainless
Cesta Borisa Kidrica 44
SI - 4270 Jesenice
Member of Slovenian Steel Group
Tel: +386 4 584 1000 Fax: +386 4 584 1111 Email: mailto:uprava@acroni.si Web: http://www.acroni.si
carbon, carbon-manganese, austenitic stainless E.A.F. / Ingot Steelmaking METAL RAVNE d.o.o. Zagreb
A, B 20 Normal Strength Sections
A, B 120 Normal Strength Bars
U1, U2, U3 105 Chain Cable Stock
2390 Ravne na Korokem
Koroka cesta 14
Tel: +386 2 870 7200 Fax: +386 2 870 7219 Email: mailto:striglav@metalravne.com Web: http://www.metalravne.com
As at 19 March 2007 41 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Con Cast Steelmaking TORE STEEL Zagreb
A 18 Normal Strength Sections
U1, U2, U3 85 Chain Cable Stock Bars
Zelezarska Cesta 3
3220 tore
Podjetje za proizvodnjo jekel d.o.o.
Tel: +386 37805 148 Fax: +386 37805 386 Email: mailto:miran.prezelj@store-steel.si Web: http://www.store-steel.si
South Africa
As below B.O.S. / Con Cast Steelmaking Highveld Steel & Vanadium Corp. Ltd. Durban
A 50 Normal Strength Plates
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,
510FG
40 Boiler & Pressure Vessel
A 12 Normal Strength Strip
360, 410 12 Boiler & Pressure Vessel
A, B 50 Normal Strength Sections
A, B 50 Normal Strength Bars
Witbank
1035
P.O. Box 111
Tel. +27 (0)13 690 9014/ (0)11 454 1453 Fax. +27 (0)13 690 9676/ (0)11 454 0576 EMail mailto:dawien@hiveld.co.za Web http://www.highveldsteel.co.za Telex
42-0088
Mpumalanga
As Below B.O.S./E.A.F./Con Cast Steelmaking MITTAL STEEL SOUTH AFRICA LTD. Johannesburg
B, D, E 30 Normal Strength Plates
A 50
AH32, AH36, DH32, DH36, EH32, EH36, FH32,
FH36
30 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 30 Boiler & Pressure Vessel
360AR, 410AR 40
LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,
LTEH36, LTFH32, LTFH36
30 Ferritic Low Temperature
PO Box 2
Vanderbijlpark, 1900
Vanderbijlpark Steel
Tel +27 (0)16 889 7695 Fax +27 (0)16 889 5668 Email: mailto:Rudolph.Steyn@mittalsteel.com Web:http://www.mittalsteelsa.com
Gauteng
Spain
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking ACELOR LAMINADOS ZARAGOZA, S.A. Zaragoza
c/Corbera Baja s/n
50015 Zaragoza
Tel: +34 976 466171 Fax: +34 976 517648 Email: mailto:tello.abia@mb.acelor.com
As below E.A.F. / Ingot Steelmaking ACERALAVA S.A. Bilbao
carbon, carbon-manganese, alloy, austenitic
stainless, duplex stainless, ferritic stainless*,
martensitic stainless*
470 Structural Bars
01470 Amurrio
Alava
Poligono Industrial De Saratxo
Tel: +34 945 891461 Fax: +34 945 393001 email: carrieta@tubacex.es
* accepted for approved applications.
As fabricated includes hot rolled and/or forged.
Approval also includes ingots up to 5 tonne and square billets up to 450 mm.
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking ACERALIA CORPORACION SIDERURGICA, S.A. Gijon
carbon, carbon-manganese 235 Slabs Semi-Finished
Apartado 90
33402 Avils
Factora de Avils
Tel: +34 985 187128 Fax: +34 985 187519 Email: mailto:jose-javier.gonzalez@arcelor.es Web page http://www.aceralia.es
Asturias
As below B.O.S. / Con Cast Steelmaking ACERALIA CORPORACION SIDERURGICA, S.A. Gijon
A, B, D, E 80 Normal Strength Plates
DH40, EH40, FH27S, FH32, FH36, FH40 25 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
80
360FG, 410FG, 460FG, 490FG, 510FG 80 Boiler & Pressure Vessel
As at 19 March 2007 42 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Apartado 570
33200 Gijn
Factori de Gijn
Specified through thickness properties for plates up to 50mm thickness.
Tel: +34 985 187128 Fax: +34 985 187519 Email: mailto:jose-javier.gonzalez@arcelor.es Web page http://www.aceralia.es
austenitic stainless E.A.F. / Con Cast Steelmaking ACEROS INOXIDABLES OLARRA S.A. Bilbao
304L, 316L, 321, 347 90 Austenitic Stainless Bars
Larrabarria 1
48150 Larrondo-Loiu
Tel: +34 944711300 Fax: +34 944531392 Email: mailto:olsa.pmadrid@olarra.com
Vizcaya
As below E.A.F. / Con Cast Steelmaking Acerinox S.A. Cadiz
304L, 316L, 321, 347 50 Austenitic Stainless Plates
304L, 316L, 321, 347 20 Austenitic Stainless Strip
11379 Los Barrios
Cadiz
Palmones
Tel: +34 956 629300 Fax: +34 956 629311
As below E.A.F. / Con Cast Steelmaking Compaia Espaola de Aceros Laminados, S.L. Barcelona
A 180 Billets Semi-Finished
A 50 Normal Strength Sections
A 35 Normal Strength Bars
08755
Castellbisbal (Barcelona)
Poligono Industrial 'San Vicente' s/n
Tel: +34 93 7730400 Fax: +34 93 7720276 Email:mailto:info@gcelsa.com Web:http://www.gcelsa.com
Approved for the supply of continuously cast billets up to 180 x 180 mm.
Steel types carbon and carbon-manganese cover the supply of billets for processing into normal strength steels according to the Society's Rules for the
Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for ordering steel which complies with their approved
chemical composition and enables them to achieve the required mechanical properties
carbon, carbon-manganese, alloy E.A.F./Ingot/Con Cast Steelmaking GSB ACERO S.A. San Sebastian
U1, U2, U3, R3, R3S 120 Chain Cable Stock Bars
carbon, carbon-manganese 120 Machinery
C/Urola 10
Apartado 55
Planta de Legazpi
Tel: +34 943 038 003 Fax: +34 943 038 013
20230 Legazpi (Guipuzcoa)
As below E.A.F. / Con Cast Steelmaking GSB ACERO S.A. San Sebastian
carbon, carbon-manganese, alloy E.A.F. / Ingot
R3, R3S 120 Chain Cable Stock Bars
U1, U2, U3, R4 152
carbon, carbon-manganese, alloy 200 Semi-finished Products
Ctra. de Zumrraga, s/n
20720 Azcoitia
Tel: +34 943 157030 Fax: +34 943 157025 Email: mailto:mdominguez@gsb.es
Guipzcoa
A, B, D, E 25 Normal Strength Fabricated Sections HIERROS MARCELINO FRANCO S.A. Gijon
AH32, AH36, DH32, DH36, EH32, EH36 25 Higher Strength
Avda. Conde Guadalhorce, 131
33400 Avils
Industrias Metlicas de Cancienes S.L. "INMECA"
Tel: +34 985 56 60 67 Fax: +34 985 566 653 EMail mailto:hifransa@infonegocio.com
Asturias
A 12 Normal Strength Strip LAMINADORA SAN JULIAN S.A. Cadiz
Km 335,5
Apartado 16
Autovia De Andalucia
Tel +34 953 5402 00 Fax +34 953 5406 08 Email mailto:laminadora1@amsystems.es
E23770 Marmolejo
A 25 Normal Strength Sections Laminados Losal, S.A. Bilbao
AH32, AH36, DH32, DH36 10 Higher Strength
Bekoibarra, 9
P.O. Box 17
Tel: +34 946251400 Fax: +34 946254976 Email: mailto:losal@losal.es Web http://www.losal.es
48300 - Gernika
A 25 Normal Strength Sections RUGUI S.L. San Sebastian
Poligono Industrial Basarte
20720 Azcoitia (Guipuzcoa)
Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:lamondarre@rugui.com
Apdo. de Correos n 8 Azpeitia (Guipuzcoa)
As at 19 March 2007 43 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Ingot Steelmaking SIDENOR INDUSTRIAL S.L. Bilbao
A 220 Normal Strength Bars
R3, R3S, R4, API-2F, R5* 180 Chain Cable Stock
carbon, carbon-manganese, alloy 220 Machinery
Paseo Alejandro Calonje, 1
39200 Reinosa (Cantabria)
Tel: +34 942775000 Fax: +34 942775283 Email: mailto:tquevedo@sidenor.com
As below E.A.F. / Con Cast Steelmaking SIDENOR, S.L. Bilbao
R3, R3S, R4, API-2F, R5* 76 Chain Cable Stock Bars
U2, U3 100
carbon, carbon-manganese, alloy 100 Semi-finished Products
Bo. Ugarte, S/N
P.O. Box 76
Fabrica de Basauri
Tel +34 944 871729 Fax +34 944 871826 Email: mailto:perdro_martinez@sidenor.com
48970 Basauri (Vizcaya)
As below E.A.F. / Con Cast Steelmaking SIDENOR, S.L. Bilbao
carbon, carbon-manganese, alloy 37 Structural Bars
carbon, carbon-manganese, alloy 37 Machinery
C/Portal De Gamarra, No. 22
01013 Vitoria (Alava)
Fabrica de Vitoria
Tel: +34 945 164649 Fax: +34 945 164748 Email: mailto:jon_a_mota@sidenor.com
Sweden
As below E.A.F. / Con Cast Steelmaking AB SANDVIK MATERIALS TECHNOLOGY Stockholm
austenitic stainless, duplex stainless E.A.F. / Ingot
austenitic stainless, duplex stainless 450 Structural Bars
austenitic stainless, duplex stainless 450 Machinery
SE-811 81 Sandviken
Tel: +46 (0) 26 26 3792 Fax: +46 (0) 26 26 3785 Email: mailto:per.yhr@sandvik.com Web http://www.smt.sandvik.com
As below E.A.F. / Con Cast Steelmaking OUTOKUMPU STAINLESS AB Stockholm
304L, 304LN, 316L, 321, 347 12 Austenitic Stainless Plates
UNS S31803, UNS 32205* 8 Duplex Stainless
304L, 316L, 321, 347 8 Austenitic Stainless Strip
Box 74
S-774 22 Avesta
Avesta Works
Tel: +46 (0)226 817 88 Fax: +46 (0)226 813 16 E-mail mailto:hans.pernang@outokumpu.com Web: http://www.outokumpu.com
*accepted for approved applications
304L, 316L, 317L, 321 5 Austenitic Stainless Strip OUTOKUMPU STAINLESS AB Stockholm
SE-64480 Torshlla
Coil Products Nyby
Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: mailto:per.nymark@outokumpu
As below E.A.F. / Con Cast Steelmaking OUTOKUMPU STAINLESS AB Kristinehamn
304L, 316L, 316LN, 321 50 Austenitic Stainless Plates
UNS S31803(MOD)* 50 Duplex Stainless
S-693 81 Degerfors
Hot Rolled Plate
Tel: 46 586 47000 Fax: 46 586 47019 Email: mailto:bengt.eriksson@outokumpu.com Web: http://www.outokumpu.com
* accepted for approved applications
UNS S31803 200 Duplex Stainless Bars OUTOKUMPU STAINLESS AB Kristinehamn
Degerfors Stainless
Tel: +46 (0)586 47000 Fax: +46 (0)586 47019 Email mailto:bengt.eriksson@outokumpu.com Web http://www.outokumpu.com
All productss with specified through thickness properties
A, B, D, E 50 Normal Strength Sections OVAKO BAR AB. Stockholm
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
A, B, D, E 40 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
40 Higher Strength
Box 5
59010 Boxholm
Boxholm Works
Tel: +46 0142 293600 Fax: +46 0142 293701
As below E.A.F. / Con Cast Steelmaking OVAKO BAR AB. Stockholm
A, B, D, E 50 Normal Strength Sections
AH32, AH36, DH32, DH36, EH32, EH36 50 Higher Strength
A, B, D, E 93 Normal Strength Bars
AH32, AH36, DH32, DH36, EH32, EH36 93 Higher Strength
carbon, carbon-manganese 93 Machinery
Smedjebacken Works
S-777 80 Smedjebacken
Tel. +46 (0)240 668372 Fax +46 (0)240 767 87 EMail mailto:lars-goran.samuelsson@fundia.com
As at 19 March 2007 44 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Ingot Steelmaking OVAKO STEEL AB. Stockholm
carbon, carbon-manganese, alloy 190 Structural Bars
U3, R3, R3S, R4 165 Chain Cable Stock
carbon, carbon-manganese, alloy 170 Machinery
SE-813 82 Hofors
Tel: +46 (0) 298 25000 Fax: +46 0298 25025 Email: mailto:bjorn.olsson@ovako.com Web: www.ovako.com
carbon, carbon-manganese, alloy 165 Structural Bars OVAKO STEEL AB. Kristinehamn
U1, U2, U3, R3, R3S, R4 165 Chain Cable Stock
carbon, carbon-manganese, alloy 165 Machinery
712 80 Hllefors
Tel +46 591 60750 Fax +46 591 60623 Email: mailto:bengt.tornblom@skf.com
As below B.O.S. / Con Cast Steelmaking SSAB Oxelosund AB. Stockholm
A, B, D, E 75 Normal Strength Plates
FH27S 40 Higher Strength
AH27S, AH32, AH36, AH40, AH42, DH27S,
DH32, DH36, DH40, EH27S, EH36
60
DH42, EH32, EH40, EH42, FH32, FH36, FH40,
FH42
70
AH46, AH50, AH55, AH62, AH69, DH46, DH50,
DH55, DH62, DH69, EH46, EH50, EH55, EH62,
EH69, FH46, FH50, FH55, FH62, FH69
80
460FG, 490FG, 510FG 60 Boiler & Pressure Vessel
360FG, 410FG 75
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,
LTFH32, LTFH36, LTFH40
40 Ferritic Low Temperature
S-61380 Oxelsund
Tel +46 155 254783 Fax +46 155 254082 Email: mailto:sten.bielmrot@oxelosund.ssab.se Web:http://www.ssab.com
All plates with specified through thickness properties.
Quality Scheme for Materials - Approval No. QA004
A 16 Normal Strength Strip SSAB Tunnplt AB. Stockholm
SE-781 84 Borlnge
Tel +46 (0)243 71459 Fax +46 (0)243 71536 Email: mailto:lars-eric.larsson@ssab.com Web: http://www.ssab.tunnplat.com
Taiwan, Republic of China
As below B.O.S. / Con Cast Steelmaking CHINA STEEL CORPORATION Kaohsiung
A, B, D, E 50 Normal Strength Plates
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
75 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
No.1 Chung Kang Road
Hsiao Kang
Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292 Web page: www.csc.com.tw
Specified through thickness properties for all grades and thicknesses, the notations Z25 and Z35 may be added
Kaohsiung
A 25 Normal Strength Bars T. S. STEEL COMPANY LTD. Kaohsiung
Tsuang-Hine Industrial Zone
Hsen-Kang
No.6 Kon-Sixth Road
Tel: +886 4 798 0060 ext 12 Fax: +886 4 798 0243
Chang-Hua
austenitic stainless, duplex stainless E.A.F. / Con Cast Steelmaking WALSIN LIHWA CORP. Kaohsiung
austenitic stainless, duplex stainless 200 Slabs Semi-Finished
austenitic stainless steel, duplex stainless steel 240 Blooms/Billets
Chin Shuei Li
Yenshui Chen
Yenshui Plant
3-10 Shi Jou Liau
Tel +886 6 6520911 ext. 407 Fax +886 6 6533076 Email mailto:nina_chen@walsin.com Web http://www.walsin.com
Tainan Hsien
As at 19 March 2007 45 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Thailand
A 50 Normal Strength Plates LPN PLATE MILL PUBLIC COMPANY LIMITED Bangkok
360AR, 410AR 40 Boiler & Pressure Vessel
Pakklong Bangplakod
Prasamutjedee
199/9 Moo 4 Suksawad Road
Tel: +66 2815 6400-9 Fax: +66 2815 6415 Email: mailto:labtest@lpngroup.co.th
Samutprakarn 10290
A 32 Normal Strength Plates SAHAVIRIYA PLATE MILL CO., LTD. Bangkok
360AR, 410AR 32 Boiler & Pressure Vessel
160 Moo 14 Sukhumvit Road
Bangpakong
Tel: +66 3883 2056-62 Fax: +66 3853 1635
Chachoengsao 24130
Turkey
As below E.A.F./Ingot/Con Cast Steelmaking Asil elik Sanayi ve Ticaret A.S. Istanbul
carbon, carbon-manganese, alloy 300 Structural Bars
carbon, carbon-manganese, alloy 220 Machinery
16800 Orhangazi-Bursa
Tel: +90 224 573 45 71 Fax: +90 224 573 45 88
Web http://www.asilcelik.com.tr
carbon, carbon-manganese E.A.F. / Con Cast Steelmaking EREGE METAL DEMIR CELIK SAN. VE TIC. A.S. Istanbul
carbon, carbon-manganese 140 Billets Semi-Finished
35800 Aliaga
Izmir
Yeni Foa Yolu 2 km
Tel: +90(0) 232 625 1320-26 Fax; +90(0) 232 625 1328-29 Email mailto:erege@erege.com Web http://www.erege.com
As below B.O.S. / Con Cast Steelmaking EREGLI DEMIR CELIK FABRIKALARI TA.S. Istanbul
A, B, D 40 Normal Strength Plates
AH32, AH36, DH32, DH36 12 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 40 Boiler & Pressure Vessel
A, B, D 15 Normal Strength Strip
AH32, AH36, DH32, DH36 12 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 15 Boiler & Pressure Vessel
KDZ. Eregli
67330
Tel: +90 (0)372 329 3838 Fax: +90 (0)372 329 5395 Email: mailto:erdinfo@erdemir.com.tr Telex 48523 EREC.TR, 48575 EDC.TR Web http://www.erdemir.com.tr
Zonguldak
As below B.O.S. / Con Cast Steelmaking ISKENDERUN DEMIR VE ELIK A.S. Istanbul
carbon-manganese 160 Billets Semi-Finished
31319, Payas
Iskenderun
Tel: +90 326 755 3082 Fax: +90 326 758 3838 Email: mailto:batesli@isdemir.com.tr
carbon, carbon-manganese B.O.S. / Con Cast Steelmaking KARDEMIR KARABUK DEMIR CELIK Istanbul
U1, U2, U3 76 Chain Cable Stock Bars
78170 Karabuk
SANAYI VE TICARET A.S.
Tel +90 370 418 2290/ 4182690 Fax +90 270 424 3661 Web http://www.kardemir.com
As below E.A.F. / Con Cast Steelmaking EMTAS ELIK MAKINA SANAYI VE TICARET
A.S.
Istanbul
carbon, carbon-manganese, alloy 160 Billets Semi-Finished
carbon, carbon-manganese, alloy 78 Structural Bars
U1, U2, U3 78 Chain Cable Stock
carbon, carbon-manganese, alloy 78 Machinery
Organize Sanayi Blgesi
A.O.S. Bulvari No. 3, P.K. 63
Tel: +90 224 243 12 30 Fax: +90 224 243 13 18 email: mailto:nozdemirel@cemtas.com.tr Web: http://www.cemtas.com.tr
16159 Bursa
A, B, D 12 Normal Strength Sections ZKAN DEMIR ELIK SAN TIC. A.S. Istanbul
AH27S, AH32, AH36, DH27S, DH32, DH36 12 Higher Strength
Ismir
Yenifoa yolu zeri 2.Km Aliaga
Tel +90 232 6251515 Fax +90 232 6251387 Email mailto:info@ozcansteel.com Internet http://www.ozkansteel.com
As at 19 March 2007 46 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Ukraine
As below B.O.S. / Con Cast Steelmaking AZOVSTAL IRON & STEEL WORKS Mykolaiv
D, E 50 Normal Strength Plates
A, B 100
AH27S, AH32, AH36, AH40, DH27S, DH32,
DH36, DH40, EH27S, EH32, EH36, EH40
50 Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50 Boiler & Pressure Vessel
1, Leporsky St.
Mariupol 87500
Tel: +380 629 227319 Fax: +380 629 530041 Telex: 115123 VOLNA UX Email mailto:geyko@azovstal.com.ua Web http://www.azovstal.com
Including plates with specified through thickness properties. Z35 may be applied to all grades and thicknesses
As Below OH/Ingot/ Con Cast Steelmaking CJSC Donetskstal Iron and Steel Works Mykolaiv
carbon, carbon-manganese 5 Ingots Semi-Finished
carbon, carbon-manganese 150 Slabs
122 Tkachenko St
Donetsk 83062
As below E.A.F. / Ingot Steelmaking ISTIL Mykolaiv
carbon, carbon-manganese, alloy 110 Structural Bars
U1, U2, U3, R3, R3S 110 Chain Cable Stock
carbon, carbon-manganese, alloy 260 Machinery
Donetsk Region
International Steel & Tube Industries Ltd.
122 Tkachenko Street
Tel: +38 (0622) 612871/613915/613052 Fax: +38 (062) 3322421/ 3322353 Email mailto:istil@istil.com.ua
As Below OH/Ingot/ Con Cast Steelmaking JSC "ALCHEVSK IRON & STEEL WORKS" Mykolaiv
D, E 45 Normal Strength Plates
B 50
A 72
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
360AR, 410AR 22 Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
360, 410 72
A 8 Normal Strength Sections
A 100 Normal Strength Bars
Lugansk Region
94202
Shmidt st. 4, Alchevsk
Tel: +38 06442 9 43 63 Fax: +38 06442 9 30 32 EMail: mailto:teslya@amk.lg.ua Web page http://www.amk.al.lg.ua
carbon, carbon-manganese E.A.F. / Ingot Steelmaking JSC "Dneprotyazhmash" Mykolaiv
carbon, carbon-manganese O H / Ingot
Post Code 49600
Dnepropetrovsk
3, Sukhoi Ostrov St.
As below B.O.S. / Con Cast Steelmaking JSC ''Mariupol Ilyich Iron & Steel Works'' Novorossiysk
E 50 Normal Strength Plates
A, B, D 80
DH40, EH40 25 Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50
360AR, 410AR, 460AR 25 Boiler & Pressure Vessel
360FG, 410FG 80
1 Levchenko Street
Mariupol 87504
Tel: +380 622 322 305/322 306 TELEX 115 157 DEPO UX
As below E.A.F. / Ingot Steelmaking JSC Electrometalurgical Works Dneprospetsstal Mykolaiv
304L, 316L, 321 215 Austenitic Stainless Bars
U1, U2, U3 85 Chain Cable Stock
carbon, carbon-manganese, alloy 300 Machinery
81 Yuzhnoye Shosse
Zaporozhye, 69008
Tel: +38 0612 39 7302 fax: +38 0612 13 1780 Email: mailto:dss@com.ua
Including forged bars and tube blanks ( billets) in all qualities.
As below B.O.S. / Ingot Steelmaking JSC Enakievo Iron and Steel Works Mykolaiv
A, B 11 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32 11 Higher Strength
Yenakievo
Donetsk region
Metallurgov Avenue, 9
Tel +38 (0)6252 53953 Fax +38 (0)6252 53953
86429
As at 19 March 2007 47 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below B.O.S. / Con Cast Steelmaking JSC KRAMATORSK IRON & STEEL WORKS Mykolaiv
A, B, D 14 Normal Strength Sections
AH27S, AH32, DH27S, DH32 14 Higher Strength
Kramatorsk, 84303
Donetsk Region
18.M.Torez, Str.
Tel +007 (0)6264 48329 Fax +007 (0)6264 48329
D 16 Normal Strength Plates OJSC "Donetsk Iron and Steel Works" Mykolaiv
A, B 20
AH27S, AH32, DH27S, DH32 20 Higher Strength
360AR, 410AR 20 Boiler & Pressure Vessel
122 Tkachenko St
Donetsk 83062
Tel: +38 0622 61 26 35 Fax: +38 0623 32 23 49 Email:mailto:oksp@donmz.donetsk.ua
Union of Myanmar
A 30 Normal Strength Plates MYANMAR ECONOMIC CORPORATION Bangkok
360AR, 410AR 30 Boiler & Pressure Vessel
HMAW BI T/S
No.2 STEEL MILL
Myaung Tagar
Tel: 007 951 250 828 Fax: 007 951 241 027 Email mailto:mecstemil2@mptmail.net.mm
United Kingdom
A, B, D, E 10 Normal Strength Sections CAPARO MERCHANT BAR PLC. Scunthorpe
AH32, AH36, DH32, DH36 10 Higher Strength
A, B, D, E 50 Normal Strength Bars
AH32, AH36, DH32, DH36 50 Higher Strength
P.O. Box 15
Scunthorpe
Caparo House
Tel +44 (0)1724 403022 Fax +44 (0)1724 403044 Email: mailto:sales@cmbplc.co.uk Web: www.cmbplc.co.uk
DN16 1XL
E 50 Normal Strength Plates CORUS (UK) Ltd Glasgow
A, B, D 100
FH40 25 Higher Strength
FH32, FH36 30
AH40, DH40, DH42, DH46, EH40, EH42, EH46 65
AH32, AH36, DH32, DH36, EH32, EH36 75
460FG, 490FG, 510FG 75 Boiler & Pressure Vessel
360FG, 410FG 100
LTFH40 25 Ferritic Low Temperature
LTAH32, LTAH36, LTAH40, LTDH32, LTDH36,
LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,
LTFH36
30
Motherwell ML1 1PU
Corus Construction & Industrial
Dalzell Works
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.com
All plates with specified through thickness properties.
APPROVED UNDER THE QUALITY SCHEME FOR MATERIALS QA030
As below B.O.S./Ingot/Con Cast Steelmaking CORUS (UK) Ltd Scunthorpe
carbon, carbon-manganese 305 Slabs Semi-Finished
carbon, carbon-manganese 355 Blooms/Billets
E 50 Normal Strength Plates
B, D 60
A 80
AH42, AH46, DH42, DH46, EH42, EH46, FH32,
FH36, FH40, FH42, FH46
25 Higher Strength
AH40, DH40, EH40 30
AH36, DH36, EH36 50
AH27S, AH32, DH27S, DH32, EH27S, EH32 60
360AR, 410AR 40 Boiler & Pressure Vessel
510FG 50
360FG, 410FG, 460FG, 490FG 60
360, 410 80
LTAH27S, LTAH32, LTAH36, LTAH40,
LTDH27S, LTDH32, LTDH36, LTDH40,
LTEH27S, LTEH32, LTEH36, LTEH40
30 Ferritic Low Temperature
A, B, D, E 50 Normal Strength Sections
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
As at 19 March 2007 48 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
P.O. Box 1
Scunthorpe DN16 1BP
Corus Construction & Industrial
Scunthorpe Works
Tel: +44 1724 405240 Fax: +44 870 9023155 Email:maito:richard.white@corusgroup.com Web:http://www.corusonline.corusgroup.com
All plates with through thickness properties.
APPROVED UNDER THE QUALITY SCHEME FOR MATERIALS QA029
A, B, D, E 77 Normal Strength Sections CORUS (UK) Ltd Middlesbrough
AH27S, AH32, AH36, DH27S, DH32, DH36 77 Higher Strength
Redcar
Teesside
Corus Construction & Industrial
Teesside Works
Tel: +44 (0)1642 406583 Fax: +44 (0)1642 406904 Email: mailto:Robin.Davies@corusgroup.com
Supply of steel ingots and slabs for subsequent rolling to plate with specific through thickness properties.
APPROVED UNDER THE QUALITY SCHEME FOR MATERIALS QA031
TS10 5RD
A, B, D, E 20 Normal Strength Sections CORUS (UK) Ltd Newcastle upon
Tyne
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
P.O. Box 1
Saltburn by the Sea
Corus Special Profiles
Skinningrove Works
Tel: +44 (0)1287 640212 Fax: +44 (0)1287 643467 Email: mailto:Bary.Atkinson@corusgroup.com
APPROVED UNDER THE QUALITY SCHEME FOR MATERIALS QA032
TS13 4ET
As below B.O.S. / Con Cast Steelmaking CORUS (UK) Ltd Newcastle upon
Tyne
carbon, carbon-manganese 295 Slabs Semi-Finished
carbon, carbon-manganese 305 Blooms/Billets
Redcar
Teesside
CORUS TEESSIDE CAST PRODUCTS
Steel House
APPROVED UNDER THE QUALITY SCHEME FOR MATERIALS QSM 033
TS10 5RD
carbon, carbon-manganese, alloy E.A.F./Ingot/Con Cast Steelmaking CORUS ENGINEERING STEELS LIMITED. Scunthorpe
U1, U2, U3, R3, R3S, R4 165 Chain Cable Stock Bars
carbon, carbon-manganese, alloy 381 Semi-finished Products
carbon, carbon-manganese, alloy 300 Machinery
PO Box 50 Aldwarke Lane
Rotherham
Rotherham & Stocksbridge Sites
Tel: +44 (0)1709 826616 Fax: +44 (0)1709 826617 Email mailto:enquiries@corusengineeringsteels.com Web page http://www.corusengineeringsteels.com
South Yorkshire S60 1DW
A 20 Normal Strength Sections CORUS TUBES Newcastle upon
Tyne
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
20 Higher Strength
Brenda Road
Hartlepool
Hartlepool Works
20 Inch H.F.I. Pipe Mill
Tel: +44 (0)1429 266611 Fax: +44 (0)1429 527275 Email: mailto:neil.wilkinson@corusgroup.com Web:http://www.corusgroup.com
Teesside TS25 2EG
U1, U2 65 Chain Cable Stock Bars NIAGARA LaSALLE (UK) LTD.- HOT ROLLED BAR Coventry (UK
Ind. Operations)
Dudley
West Midlands
Peartree Lane
Woodside
Tel +44 (0)121 506 7500 Fax +44 (0)121 506 7501 Email: mailto:hotrolled@niag.com
DY2 0QS
A 50 Normal Strength Sections NIAGARA LaSALLE (UK) LTD.- HOT ROLLED BAR Coventry (UK
Ind. Operations)
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
32 Higher Strength
A 50 Normal Strength Bars
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
50 Higher Strength
As at 19 March 2007 49 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Bull Lane Moxley
Wednesbury
Ductile Wesson - Gadd Dudley Port
Victoria Steelworks
Tel: +44 (0)121 506 7582 Fax: +44 (0)121 506 7501 Email: mailto:jcook@niag.com
West Midlands WS10 8RS
stainless steel E.A.F/A.O.D/L.A.F/ConCast Steelmaking Outokumpu Stainless Ltd. Scunthorpe
stainless steel Slabs Semi-Finished
stainless steel Blooms/Billets
304L, 316L, 317L, 321, 347 6 Austenitic Stainless Strip
P.O. Box 161
Shepcote Lane
The approval for steelmaking and slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitation
hardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international or
national standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approved
chemical composition to enables them to achieve the required physical and mechanical properties.
Tel: +44 (0)114 244 3311 Fax: +44 0114 2014759 Email: mailto:tony.stephenson@outokumpu.com Web: http://www.outokumpu.com
Sheffield, S9 1TR
carbon, carbon-manganese, alloy, austenitic
stainless
E.A.F. / Ingot Steelmaking SHEFFIELD FORGEMASTERS INTERNATIONAL Ltd. Scunthorpe
Brightside Lane
Sheffield S9 2RW
P.O. Box 286
Tel: +44 (0)114 2449071 Fax: +44 (0)114 2422103 Email:mailto:sales@sfel.com Web:http://wwwsheffieldforgemasters.com
United States of America
As below E.A.F. / Con Cast Steelmaking Citisteel USA, Inc. Philadelphia
A, B 30 Normal Strength Plates
4001 Philadelphia Pike
Claymont
Claymont, DE.
Tel: +1 302 792 5403 Fax: +1 302 792 0203
DE 19703-2794
carbon, carbon-manganese, alloy E.A.F. / Ingot Steelmaking ELLWOOD QUALITY STEEL COMPANY Chicago
700 Moravia Street
New Castle
Tel: +1 724 654 4441 Fax: +1 724 658 6849 Email mailto:slubinski@eqs.elwd.com
Ingots and Blooms for forgings
Pennsylvania 16101
As below E.A.F. / Con Cast Steelmaking IPSCO Steel (Alabama) Inc. New Orleans
A, B 50 Normal Strength Plates
AH27S, AH32, AH36, DH32, DH36 38 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 38 Boiler & Pressure Vessel
Axis
Alabama 36050
12400 Highway 43 North
Tel: + 01 256-546-2669 Fax: +01 256-546-2670 email mailto:lbridges@ipsco.com Web http://www.ipsco.com
As below B.O.S. / Con Cast Steelmaking MITTAL STEEL USA Chicago
D 35 Normal Strength Plates
A, B 50
AH27S, AH32, AH36, DH27S, DH32, DH36,
EH27S, EH32, EH36
75 Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 75 Boiler & Pressure Vessel
Burns Harbor
IN 46304-9745
250 West Highway 12
Tel: +1 219 787 4553 Fax: 1 219 787 2139 Email mailto:daniel.elwood@mittalsteel.com
As below E.A.F. / Con Cast Steelmaking NUCOR STEEL TUSCALOOSA INC. New Orleans
A 20 Normal Strength Plates
A 20 Normal Strength Strip
360FG, 410FG 20 Boiler & Pressure Vessel
Tuscaloosa
AL 35404-1000
1700 Holt Road N.E.
A, B, D 50 Normal Strength Plates Oregon Steel Mills Los Angeles
AH27S, AH32, AH36, DH27S, DH32, DH36 12 Higher Strength
360AR, 410AR 40 Boiler & Pressure Vessel
360FG, 410FG 50
P.O. Box 5300
Portland
Tel: +1 503 978 6178 Fax: +1 503 240 5268
Oregon OR 97228
As at 19 March 2007 50 Page
Name and Address Max Thickness/Diameter (mm) Grade Category Product
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As below E.A.F. / Con Cast Steelmaking Republic Technologies International Inc. Cleveland
As below E.A.F. / Ingot
carbon, carbon-manganese 365 Semi-finished Products Bars
2633 Eighth Street N.E.
Canton
Hot Rolled Bar Division
Tel: +1 330 438 5600 Fax: +1 330 438 5695 Email: mailto:bgarver@republicengineered.com
Ohio 44704-2311
As below E.A.F. / Con Cast Steelmaking The Timken Company Steel Business Cleveland
As below E.A.F. / Ingot
carbon, carbon-manganese, alloy 330 Structural Bars
carbon, carbon-manganese, alloy 330 Machinery
Canton
OH 44706-0932
1835 Dueber Avenue S.W.
Tel: +1 330 471 4114 Fax: +1 330 471 4077 Email: mailto:barbara.mardyla@timken.com
As at 19 March 2007 51 Page