F.

Example Calculations
Design a CMU pier and ground anchor foundation for a manufactured home to be placed in
an SFHA Zone AE having a ood velocity of 2 fps. The BFE is 9 feet and existing ground eleva-
tion is approximately 7 feet. The ood depth is 2 feet and the freeboard is 1 foot, which yields
a DFE depth of 3 feet. The manufactured home dimensions for these example calculations are
shown in Figure F-1. The manufactured home is a single unit, 16 feet wide and 60 feet long
with a 30-degree gable roof with a 1-foot overhang. Roong members are spaced 16 inches on
center (o.c.). The manufactured home weighs 20 psf. Assume an NFPA 5000 soil classication
of soft, sandy clay, or clay (allowable bearing pressure q
a
=1,000 psf ; ultimate bearing pressure
q
u
= 2,000 psf). Use ASCE 7 to calculate loads.
Foundation loads selected for this example of a manufactured home in an SFHA differ from
those that may be found in HUD standard 24 CFR 3280. Design loads in this example are in ac-
cordance with ASCE 7-05 and other standards.
These example calculations assume transverse wind loads produce the controlling loading.
Wind in the direction parallel to the roof ridge may produce greater loads for certain cases and
must be evaluated during nal design.
Figure F-1. Manufactured
home dimensions.

ASCE 7-05
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-1
F EXAMPLE CALCULATIONS
Step 1: Determine Design Criteria
NORMAL LOADS
Dead Load (D)
D = 20 psf Given in the example statement
Live Load (L)
L is based on one- and two-family dwellings
L = 40 psf
Roof Live Load (L
r
)
L
r
= 20R
1
R
2
=20(1)(0.85)=17 psf
R
1
= 1 for A
t
200 ft
2
A
t
= 2(9.2 ft)(16 in) =24.5 ft
2
F = number of inches of rise per foot
F = 1ft tan 30 = 7 in
Note that the roof live load falls between the limits giv-
en:
12 L
r
20
ENVIRONMENTAL LOADS
Wind Loading
Structure is a regular shape, located in a windborne debris region with
terrain classication of Exposure C and surrounded by at terrain.
Mean roof height (h)
h = 3 ft + 10 ft + 0.5(4 ft)
= 15 ft
h < 16 ft (least horizontal dimension)
Calculations are for a foundation system, which is a main wind force re-
sisting system (MWFRS).
Velocity Pressures
Velocity pressures are determined using
Method 2: Analytical Procedure

ASCE 7-05
Table 4-1
ASCE 7-05
Section 6.2
Section 6.5
1 ft
12 in
( )
12 in
1 ft
( )
F-2 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
(A simplied alternative is to use ASCE 7, Section 6.4, Method 1. Wind
pressures are tabulated for basic conditions. The wind pressure must be
adjusted for mean roof height and exposure category.)
Velocity Pressure Coefcient (q
z
)
q
z
= 0.00256K
z
K
zt
K
d
V
2
I
Velocity pressure exposure coefcient evaluated at height z (the
height above ground level in feet) (K
z
)
K
z
= 0.85
Topographical factor (K
zt
)
K
zt
=1 (assume a at surface)
Wind directionality factor (K
d
)
K
d
= 0.85
Basic Wind Speed (V)
V = 110 mph (3-second gust)
I = 1 (Category II building: Table 1-1 (ASCE 7))
Therefore, q
z
= 0.00256(0.85)(1)(0.85)(110)
2
(1)
= 23 psf
Design Pressures for MWFRS
Internal Pressure Coefcient (GC
pi
)
GC
pi
= 0.18
External Pressure Coefcient (C
p
)
h = Mean roof height, in feet
L = Horizontal dimension of building, in feet, measured par-
allel to wind direction
B = Horizontal dimension of building, in feet, measured nor-
mal to wind direction
Table F-1 shows the External Pressure Coefcients calculated for the
windward, leeward and side walls. Computations of the External Pres-
sure Coefcients for the windward and leeward roof are shown Table
F-2.

Section 6.5.10
Eq. 6-15
Section 6.5.6
Table 6-3
Section 6.5.6
Section 6.5.4.4
Section 6.5.5
Table 6-1
Section 6.5.4
Section 6.5.11.1
Figure 6-5
Section 6.5.11.2.1
Figure 6-6
Figure 6-6
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-3
F EXAMPLE CALCULATIONS
Table F-1. External Wall Pressure Coefcients
Surface Wind Direction L/B C
p
Windward Wall n/a n/a 0.8
Leeward Wall
Perpendicular to
roof ridge
-0.5
Side Wall n/a n/a -0.7
Table F-2. External Roof Pressure Coefcients
Surface Wind Direction h/L C
p
Windward Roof
Perpendicular to
roof ridge
-0.3
0.2
Leeward Roof -0.6
Foundation systems are considered rigid, therefore, G = 0.85.
Design Pressure (p)
The basic pressure equation (ASCE 7 6-17), which includes the internal
pressure coefcient is as follows:
p = qGC
p
q
i
(GC
pi
)
However, this would only be used if designing individual components
whose effective tributary area is equal to or greater than 700 sf (ASCE
7-05 6.5.12.1.3 and IBC 2006 1607.11.2.1). When determining loads on
the global structure (i.e., shear walls or foundation design), the inter-
nal pressure components will act in equal and opposite directions on
the roof/oor and the leeward/windward walls, thereby algebraical-
ly canceling each other. The resulting simplied form of the pressure
equation is:
p = q x GC
p

Table F-3 summarizes the design pressures calculated using this simpli-
ed wind design pressure equation. Figure F-2 shows the application of
these design pressures on the structure. For foundation design, internal
pressures need not be considered since internal pressure on windward
walls, leeward walls, oors, and roofs cancel each other. For example,
internal pressures acting on a windward wall are equal and opposite to
those acting on a leeward wall and the net force on the foundation from
internal pressures is zero.
15 ft
16 ft
= 0.94
16 ft
60 ft
= 0.27
Figure 6-6
Figure 6-6
Section 6.5.8
Eq. 6-17
F-4 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
While internal pressures cancel, internal pressures for a partially en-
closed building have been included in the example. This is to provide
an example of more general wind load calculations.
Table F-3. Design Pressures for Wind Perpendicular to the Roof Ridge
Surface
Design Wind Pressure
Calculations
pressure
(psf)
Windward Wall p = 23 psf(0.85)(0.8) 15.7
Leeward Wall p = 23 psf(0.85)(-0.5) -9.8
Side Walls p = 23 psf(0.85)(-0.7) -13.7
Windward Roof
p = 23 psf(0.85)(-0.3) -5.9
p = 23 psf(0.85)(0.2) 4.0
Leeward Roof p = 23 psf(0.85)(-0.6) -11.8
MWFRS Roof Overhang Pressures
ASCE 7 only addresses the windward overhang, specifying the use of a
positive pressure coefcient of C
p
= 0.8. Acting on the bottom surface of
the overhang in combination with pressures acting on the top surface.
For the leeward overhang, the coefcient for the leeward wall (C
p
= -0.5)
could be used, but the coefcient has been conservatively taken as zero.
p = 23 psf(0.85)(0.8)
= 15.7 psf
p
OH
= -5.9 psf 15.7 psf = -21.6 psf
A conservative simplication is to use the wind pressure acting away from
the roof case for uplift roof pressure simultaneously with the wind pres-
sure toward the roof for the lateral roof pressure.
ASCE 7-05
Section 6.5.11.4.1
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-5
F EXAMPLE CALCULATIONS
Figure F-2. Maximum
uplift and lateral wind
loads on roof.
SNOW LOADING
Ground Snow Load (p
g
)
p
g
= 20 psf
Flat Roof Snow Load (p
f
)
p
f
= 0.7C
e
C
t
Ip
g
p
f
= 0.7(1.0)(1.0)(1.0)(20)
= 14 psf
But not less than p
f
=(I)p
g
= 20 psf
ASCE 7-05
Section 7.2
Figure 7-1
Section 7.3
Eq. 7-1
F-6 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
Section 7.3.1
Table 7-2
Section 7.3.2
Table 7-3
Section 7.3.3
Table 7-4
Section 7.4
Eq. 7-2
Section 7.4.1
Figure 7-2
Section 7.6
Section 7.6.1
Figure 7-9
Eq. 7-3
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-7
Exposure Coefcient (C
e
)
C
e
= 1.0 (partially exposed roof)
Thermal Factor (C
t
)
C
t
= 1.0
Importance Factor (I)
I = 1.0 (Category II building: Table 7-4 (ASCE 7))
Sloped Roof Snow Load (p
s
)
p
s
= C
s
p
f

= (1.0)(20 psf)
= 20 psf
Warm Roof Slope Factor (C
s
)
C
s
= 1.0 (asphalt shingle not slippery)
Unbalanced Roof Snow Load (p
u
)
Since the roofs eave to ridge distance 20 ft, unbalanced uniform snow
loads shall be applied as follows:
P
windward
= 0.3 p
s
= 6 psf
P
leeward.1
= p
s
= 20 psf
P
leeward.2
= (h
d
)()/(S)
= (1.44 ft)(16.6 pcf)/(1.73)
= 18.2 psf
From the ridge toward the leeward eave a distance of:
x = (8/3)(h
d
)(S)
= 5.1 ft
h
d
= 1.44 ft
= 0.13 p
g
+ 14 30 pcf
= 16.6 pcf
F EXAMPLE CALCULATIONS
FLOOD LOADING
Hydrostatic Load (F
h
)
If the manufactured home is elevated above the BFE on
an enclosed foundation, venting must be provided in all
manufactured homes placed in a SFHA; the hydrostatic
forces on either side of the foundation wall will cancel.
However, the hydrostatic load is calculated because it is
used in the hydrodynamic load calculation.
F
h
= P
h
H
Hydrostatic Pressure (P
h
)
P
h
= H
Specic Weight of Fresh Water ()
= 62.4 pcf
Floodproong Design Depth (H)
H = 2 ft (base ood depth) + 1 ft
Hydrodynamic Load
The hydrodynamic load is calculated by converting it to an equivalent
hydrostatic load by increasing the ood depth. The increase in ood
depth is referred to as d
h.
Drag Coefcient (C
d
)
In the above equation, a value of 2.0 was assumed
for C
d
. This is a conservative estimate; the actual
value for C
d
could be anywhere between 1.2 and
2.0.
Acceleration Due to Gravity (g)
g = 32.2 ft/s
2
with a hydrodynamic pressure of
P
hydr
= (d
h
) = 62.4 pcf (0.13 ft) = 8.2 psf
The equivalent hydrostatic load (F
h/ad
) taken into consid-
eration the hydrodynamic load is :
F
h/ad
= P
hydr
x H = 8.2 psf x3 ft = 24.6 plf
ASCE 7
Eq. 7-5
C
d
V
2
2g
d
h
= = = 0.13 ft
2.0(2
ft
/
s
)
2
2(32.2
ft
/
s
)
FEMAs Coastal Construction Man-
ual (FEMA 55) recommends a value
of 2.0 for square or rectangular piles
and 1.2 for round piles.
For additional guidance regarding
drag coefcients, refer to Volume II
of the U.S. Army Corps of Engineers
Shore Protection Manual (USACE
1984), FEMA 55, and the Engineering
Principles and Practices for Retro-
tting Flood-Prone Residential Struc-
tures (FEMA 259).
Note: A 1-foot freeboard is added
to the BFE depth to provide a
protection above the BFE; 3 feet
becomes the design depth or the
DFE.
F-8 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
Since piers are 16 inches wide, the total hydrodynamic force on
the pier is

CHECK SCOUR
Reference: Publication No. FHWA NHI 00-001, Evaluating Scour at Bridges, 4th Edition, May 2001,
Hydraulic Engineering Circular No. 18.
Y
s
= 2.0 x (K
1
)x (K
2
) x(K
3
) x(K
4
) x (a/Y
1
)
0.65
x F
r1
0.43

Y
1
Where: Y

= Scour depth
Y
1
= Flow depth directly upstream of pier
a = Pier width (ft.)
L = Pier length (ft)
F
r1
= Froude number
F
r1
= V
1
/(gY
1
)
1/2

Where V
1
= Mean velocity of fow directly upstream of pier
g = acceleration due to gravity (32.2 feet/sec
2
)
lb
ft
= 24.6 16 in 32 lbs per pier
1 ft
12 in
L = 16"
a = 8"
L = 16"
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-9
F EXAMPLE CALCULATIONS
K
1
= Factor for pier nose shape. For square nose
K
2
= Factor for Angle of attack . K
2
= (cosine + (L/a) x sine )
0.65
K
3
= Factor for bed condition/. K
3
= 1.1
K
4
= Factor for armoring by bed material size.
Project parameters:
Flood low = 2 fps
Flood depth = 3 ft
Assume food angle of attack = 0
So that:
K
1
= 1.1 (Table 6.1)
K
2
= [cosine 0
o
+(L/a)x sine 0
0
]
0.65
= [1.00 + (1.33/0.67) x 0]
0.65
= 1.00
K
3
= Factor for bed condition/. K
3
= 1.1 (Table 6.3)
K
4
= Factor for armoring by bed material size. K
4
= 1.0 unarmored
F
r1
= V
1
/(gY
1
)
1/2
= 2/[32.2 x 3]
1/2
=2/9.84 = 0.203
And
Y
s
= (2) x (1.1) x (1.0) x (1.1) x (1.0) x (0.67/2)
0.65
x (0.203)
0.43

Y
1
Y
s
= (2.42) x (0.491) x (.504) = 0.6
Y
1
Y
s
= (0.6) x (Y
1
) = (0.6)x(3) = 1.8 ft
Scour protection or increased footing embedment required.
F-10 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
Step 2: Select a Design Methodology and Assess Load
Combinations and Failure Modes
Figure F-3 illustrates the loads applied to the manufactured home. Table F-4 lists the nomencla-
ture of the applied loads shown in Figure F-3.
Table F-4. Load Nomenclature
Nomenclature Load Description
D dead load
L live load
L
R
roof live load
R
H
horizontal reaction
R
LV
leeward vertical reaction
R
WV
windward vertical reaction
S
B
balanced snow load
W
H
horizontal wall wind pressure
W
RH
roof horizontal wind pressure
Figure F-3. Loading on a
manufactured home.
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-11
F EXAMPLE CALCULATIONS
Nomenclature Load Description
W
LRV
leeward roof vertical wind pressure
W
WRV
windward roof vertical wind pressure
Note that snow load governs over roof live load and wind downward load, and wind lateral
load governs over earthquake lateral load. Load combinations for non-governing cases are not
shown.
For the purposes of these calculations, the worst case wind load is taken to be perpendicular to
the roof ridge for all failure modes. Wind in the direction parallel to the roof ridge may pro-
duce greater loads for certain failure modes.
Uplift and Downward Failure Mode
Uplift failure is a vertical force phenomenon. The loads that act vertically are wind, snow, dead,
and live loads. Table F-5 summarizes the loads that inuence uplift and downward failure mode.
Table F-6 assesses uplift and downward failure load combinations. Note that uplift is based on
MWFRS pressures for the global foundation design. Design of the connections to the founda-
tion may require components and cladding (C&C) pressures to be used.
Table F-5. Vertical Load Values
Load
Type
Total load acting on the structure and, therefore, must be supported by the foundation
D D = [dead load per square foot][width of the manufactured home]
D = [20 psf][16 ft]
D = 320 lbs per linear ft of manufactured home length
L L = [live load per square foot][width of the manufactured home]
L = [40 psf][16 ft]
L = 640 lbs per linear ft of manufactured home length
L
r
L
r
= [roof live load per square foot][width of the manufactured home]
L
r
= [17 psf][18 ft]
L
r
= 306 lbs per linear ft of manufactured home length
Table F-4. Load Nomenclature (continued)
F-12 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
Load
Type
Total load acting on the structure and, therefore, must be supported by the foundation
W Maximum wind uplift loads occur for winds parallel to the roof ridge at the windward end.
W = W
WRV
+W
LRV
= [(vertical component roof wind pressures)(area roof)]/manufactured home length
W = [-17.6 psf][(9 ft)(15 ft)(2)] 0 ft to 15 ft +
[-9.8 psf][(9 ft)(15 ft)(2)] 15 ft to 30 ft +
[-5.9 psf][(9 ft)(30 ft)(2)] 30 ft to 60 ft
W = -10,584 lbs/60 ft = -176 lbs per linear foot of manufactured home length (average)
In this case, vertical uplift loads are low and so this simplication is acceptable. However, to
account for the unbalanced uplift if wind loads were higher, either overturning in this direction
would need to be considered, or the windward uplifts conservatively made symmetrical about the
middle.
Maximum wind downward loads occur for wind perpendicular to the roof ridge; however, they are
much less than, and do not govern over, roof live or snow loads.
S S = [snow pressure][horizontal projected roof area]
S = [20 psf][(9 ft)]SW + [20 psf][(9 ft)]SL
S = 360 lbs per linear ft of manufactured home length
Table F-6. Vertical Failure Mode ASD Load Combinations
Load Combinations
4
D + 0.75L + 0.75S
320 lbs + 0.75(640 lbs) + 0.75(360 lbs) = 1,070 lbs per linear ft of manufactured home length
7
0.6D + W
0.6(320 lbs) - 176 lbs = 16 lbs per linear ft of manufactured home length acting downward
Note that, for load combination 7, the 0.6 load factor should be applied to the dead load that
would actually be present over the whole structure. Additions to the dead load tabulation such
as mechanical and miscellaneous or shingles should not be included in this value as they may
not be present in all areas or during a high-wind event and their inclusion would not be con-
servative.
Sliding or Shearing Failure Mode
Sliding failure is a lateral force phenomenon. The loads that act laterally are wind and ood
loads. Table F-7 summarizes the lateral loads and their values. Maximum lateral wind loads oc-
cur when the wind is perpendicular to the roof ridge. Note that lateral wind loads act on the
overall structure (i.e., foundation), whereas ood loads act on the individual piers. Table F-8
gives the load combinations for sliding failure. Once the number of piers is dened, the hy-
drodynamic forces on these piers are to be added to load combination 4, and the foundation
design will have to be checked to make sure it can resist the added hydrodynamic loads.
Table F-5. Vertical Load Values (continued)
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-13
F EXAMPLE CALCULATIONS
Table F-7. Lateral Load Values
Load
Type
Total load acting on the structure and, therefore, must be supported by the foundation
W Maximum lateral wind loads occur for winds

to the roof ridge

W = W
RH
+ W
H
=
[lateral roof pressures][roof height] + [wall pressures][wall height]
W = [4 psf (-11.8 psf)] (4.7 ft)
[(15.7 psf + 9.8 psf)(10 ft)]
W = 329.3 lbs per linear ft of manufactured home length
F
a
Hydrodynamic load per pier
F
a
= [hydrodynamic force][pier length]
F
a
= 32.8 lbs per pier
Assume total of 9 piers x 2 rows for 1
st
iteration
F
a
= (32.8 lbs per pier)(9 piers per row)(2 rows)
F
a
= 590.4 lbs / 60 ft = 9.84 lbs per linear ft of manufactured home length
Table F-8. Sliding Load Combinations
Load Combinations
5 W + 1.5F
a
329.3 lbs + 1.5(9.84 lbs) = 344 lbs per linear ft of manufactured home length
Note: The vertical gravity loads are not considered to be conservative. Thus, the frictional re-
sistance of the footings under the piers has been neglected. This component may be used in
borderline situations at the discretion of the engineer.
Overturning Failure Mode
Overturning failure results from loads that act on the whole structure and pivot about the bot-
tom of the leeward pier. Dead, live, wind, and snow loads can all inuence the overturning
moment. Table F-9 summarizes the moments that affect overturning due to wind in this case.
Table F-10 assesses the moment load combinations. Only the portions of the roof and oor
live loads that are over the part that cantilevers out past the leeward pier will contribute to the
overturning. Since this is the worst overturning case for each, only these conditions will be cal-
culated.
F-14 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
Table F-9. Moment Load Values
Moment
Type
Total moment about the bottom of the leeward foundation support
(positive moment is counter clockwise)
D D = [dead load per square foot][home width][moment arm]
D = [20 psf][(16 ft)(4 ft)]
D = +1,280 ft-lbs per linear ft of manufactured home length
L L
1
= [live load per square foot][home width][moment arm]
L
1
= [40 psf][(16 ft)(4 ft)]
L
1
= 2,560 ft-lbs per linear ft of manufactured home length
L
2
= [live load per square foot][cantilever width][moment arm]
L
2
= [40psf][4 ft][-1 ft]
L
2
= -160 ft lbs per linear ft of manufactured home length
L
r
L
r
= [roof live load per square foot][roof width][moment arm]
L
r
= [17 psf][4 ft][1 ft]
L
r
= -68 ft-lbs per linear ft of manufactured home length
W WIND PERPENDICULAR TO THE ROOF RIDGE
W
WRV
= [vertical component roof wind pressures][roof width][moment arm]
W
WRV
(-21.6 psf)(1 ft)(12.5 ft) + (-5.9 psf)(8 ft)(8 ft)
W
WRV
= -648 ft-lbs per linear ft of manufactured home length
W
LRV
= [vertical component roof wind pressures][roof width][moment arm]
W
LRV
(-11.8 psf)(9 ft)(-0.5 ft)
W
LRV
= +53 ft-lbs per linear ft of manufactured home length
W
RH
= [horizontal component roof wind pressures][roof height][moment arm]
W
RH
= [4 psf (-11.8 psf)](-4.67 ft)](15.3 ft)
W
RH
= -1,129 ft-lbs per linear ft of manufactured home length
W
W+L
= [windward wall pressure + leeward wall pressure][homes height from ground to roof
eave][moment arm]
W
W+L
= [15.7 psf + 9.8 psf](10 ft)(-8 ft)
W
W+L
= -2,040 ft-lbs per linear ft of manufactured home length
F
a
Hydrodynamic load on piers
F
a
= [horizontal component][moment arm]
= (9.84 plf)(-3 ft/2) = -15 ft-lbs per linear foot of manufactured home length
S S
B
= [balanced snow pressure][horizontal projected roof area][moment arm]
S
B
= [20 psf][18 ft][-4 ft]
S
B
= 1,440 ft-lbs per linear ft of manufactured home length
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-15
F EXAMPLE CALCULATIONS
Table F-10. Overturning Load Combinations
Moment Load Combinations (positive moment is counter clockwise)
6 D + 0.75W + 0.75L + 0.75L
r
+ 1.5F
a
(Partial live loading to produce max OT)
(1,280 ft-lbs) + (0.75)(-648 ft-lbs + 53 ft-lbs 1,129 ft-lbs 2,040 ft-lbs) + (0.75)(-160 ft-lbs)+
(0.75)
(-68 ft-lbs) + (1.5)(-15 ft-lbs) = -1,737 ft-lbs per linear ft of manufactured home length
D + 0.75W + 0.75L + 0.75S + 1.5F
a
(Full live and snow to produce max downward reaction)
(1,280 ft-lbs) + (0.75)(-648 ft-lbs + 53 ft-lbs 1,129 ft-lbs 2,040 ft-lbs) + (0.75)(-2,560 ft-lbs) +
(0.75)(1,440 ft-lbs) + (1.5)(-15 ft-lbs) = 1,435 ft-lbs per linear ft of manufactured home length
7 0.6D + W + 1.5F
a
(0.6)(1,280 ft-lbs) + (-648 ft-lbs + 53 ft-lbs 1,129 ft-lbs 2,040 ft-lbs) + (1.5)(-15 ft-lbs)
= -3,019 ft-lbs per linear ft of manufactured home length
Table F-11 summarizes the load combinations that govern for each of the three failure modes.
The maximum roof vertical and lateral load cases are assumed to act simultaneously as a con-
servative simplication.
Table F-11. ASD Load Combinations for Example Problem (loads are in pounds per linear foot)
Failure
Modes
Load Combinations
4 5 7
Uplift 1,070 lbs n/a
1
15 lbs
Sliding n/a
1
313 lbs n/a
1
Overturning n/a
1
n/a
1
-979 ft-lbs
1
Load combination does not govern.
Load combinations 1-3 do not govern. Load combination 6 does not comply with HUD 24 CFR 3280.
Step 3: Select Foundation Type and Materials
The example statement specied a CMU pier and ground anchor foundation type. Since the
ood velocity is 2 fps, CMU piers must have surface bonded mortar that meets ASTM C887-79a
(2001) and ASTM C946-91 (2001) and maintain bonding between CMUs.
Step 4: Determine Forces at Connections and on Foundation
Components
CMU piers transfer the compressive loads from the manufactured home into footings and
then into the ground. The masonry piers are not considered to provide any lateral or uplift
F-16 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
resistance. The governing load combination for downward forces is the vertical failure mode
(load combination 4), which produces a total downward force from the manufactured home
equal to
(downward force)(length of manufactured home)
Therefore, (1,070 lbs)(60 ft) = 64,200 lbs
This downward force governs the number of footings and, therefore, piers needed to transfer
the downward load into the ground.
Following the braced masonry pre-engineered foundation design for ood velocities over 2 fps
specication given in Chapter 10 of the use of a dry-stack 16-inch by 8-inch block pier with a
minimum of an 1/4-inch thick surface bonded mortar and a 24-inch square, 10-inch deep foot-
ing, calculate the number of footings needed to adequately transfer the downward loads to the
ground.
Required footing area =
Consult the geotechnical engineer for the ultimate soil bearing capacity value. An approximate
method to calculate the ultimate soil bearing capacity is to multiply the allowable soil bearing
capacity by a safety factor. The maximum pressure given in the NFPA 5000 Soil Classication
Table can also be used as the ultimate soil bearing capacity.
Required footing area = = 64 ft
2
Individual footing area = (24 in x 24 in) = 4 ft
2
Number of footings =
= = 16 footings/piers
Therefore, provide 8 piers per side of the manufactured home
Pier spacing =
= = 8.6 ft
The maximum spacing of the piers is set to 8 feet to provide effective oodborne debris protec-
tion. To protect against oodborne debris, it is assumed that 1 pier will be lost due to oodborne
debris.
Minimum number of piers = +1= 8.5 piers, say 9 piers per side (i.e., 8 spaces at 7.5
feet). Therefore, the home will be supported by a total of 18 piers (9 piers on each side)
spaced at 7.5 feet.
comprehensive load
allowable soil bearing capacity
64,200 lbs
1,000 psf
1 ft
2
144 in
2 ( )
total required footing area
individual footing area
64 ft
2
4 ft
2
manufactured home length
(number piers per side-1)
60 ft
8-1
60 ft
2
8 ft
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-17
F EXAMPLE CALCULATIONS
Lateral wind loads are resisted by the strapping and ground anchors. The nal number of piers
equals the initial guess; therefore, the lateral load on the piers does not have to be updated.
Calculate the number of anchors needed to resist sliding failure.
The recommended design stiffness of the anchors in Table 7-5 in this guide is given for 5-foot
anchors installed at 45 degrees and axially loaded is 1,200 lb/in (Figure 7-4). The horizontal
component of the ground anchors strength is equal to
(1,200 lbs/in)(cos 45) = 848 lb/in
The manufactured home industry gives an allowable lateral manufactured home movement of
3 inches. So the total lateral strength of a ground anchor is (3 in)(848 lbs) = 2,544 lbs.
Number of ground anchors needed =
Number of ground anchors needed = = 8 anchors per side
Calculate ground anchor spacing = = 8.5 ft
The anchor strapping should attach into a wall stud; therefore, anchor spacing must be adjusted
to 16-inch increments.
Both uplift and overturning failure modes are resisted by the vertical strength of ground an-
chors. The uplift forces will be resisted by all the ground anchors and the overturning moment
will be resisted only by the windward ground anchors.
For the worst uplift of the vertical failure mode, load combination 7 (refer to Table F-6) governs.
However, the maximum net uplift is 16 plf downward, which means that overturning will govern
the uplift requirements.
For the overturning failure mode, load combination 7 (refer to Table F-10) governs for wind
perpendicular to the roof ridge. Overturning moment is only resisted by the windward anchors.
Therefore, the total vertical load each anchor will have to resist is
= 612 lbs per anchor
The vertical component of the anchor stiffness equals
(1,200 lbs/in)(cos 45) = 848 lbs/in
The manufactured home industry gives an allowable vertical movement of 2 inches. This results
in a vertical strength per anchor equal to
(2 in)(848 lbs/in) = 1,697 lbs per anchor
60 ft
(8-1)
(979 ft-lbs)(60 ft)
12 ft
8 anchors
(overturning moment)(length of home)
moment arm
number of anchors per side
=
lateral load
anchors lateral capacity
(313 lb)(60 ft)
2.544 lbs
F-18 PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
EXAMPLE CALCULATIONS F
This is more than the strength needed by each anchor to resist the overturning moment.
The anchor strapping should attach into a wall stud and, therefore, anchor spacing must be ad-
justed to 16-inch increments. Place anchors at each end of the home and space at 72 inches.
For the overturning case, the connection of the straps to the stud and the ground anchor em-
bedment is based on MWFRS pressures. However, although it would likely not govern, to be
thorough, the uplift only condition using C&C pressures should be checked for these two an-
chorages (straps to studs and anchors in ground).
Step 5: Specify Connections and Framing Methods Along with
Component Dimensions to Satisfy Load Conditions
The CMU pier and ground anchor foundation will consist of 16 dry-stack, 16-inch by 8-inch
block piers with a minimum of a 1/4-inch thick surface bonded mortar and 24-inch square,
10-inch deep footings. Ground anchors will be placed at 45-degree angles at each end of the
manufactured home and spaced at 72 inches.
Step 6: Note All Design Assumptions and Details on Drawings
Refer to pre-engineering foundation design drawings contained in Appendix H and specica-
tions presented in Chapter 10 herein as to how to adequately document assumptions and detail
drawings.
PROTECTING MANUFACTURED HOMES FROM FLOODS AND OTHER HAZARDS
A Mul ti - Hazard Foundati on and I nstal l ati on Gui de
F-19