Service Manual: 6632LCT/6632LG

SERVICE MANUAL
32 COLOR LCD TELEVISION
6632LCT/6632LG
IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all
Funai Equipment. The service procedures recommended by Funai and
described in this service manual are effective methods of performing
service operations. Some of these service special tools should be used
when and as recommended.
It is important to note that this service manual contains various CAUTIONS
and NOTICES which should be carefully read in order to minimize the risk
of personal injury to service personnel. The possibility exists that improper
service methods may damage the equipment. It also is important to
understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE.
Funai could not possibly know, evaluate and advice the service trade of all
conceivable ways in which service might be done or of the possible
hazardous consequences of each way. Consequently, Funai has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a
service procedure or tool which is not recommended by Funai must first
use all precautions thoroughly so that neither his safety nor the safe
operation of the equipment will be jeopardized by the service method
selected.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
How to initialize the LCD Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Schematic Diagrams / CBAs and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
The LCD panel is manufactured to provide many years of useful life.

Occasionally a few non active pixels may appear as a tiny spec of color.
This is not to be considered a defect in the LCD screen.
SPECIFICATIONS
< TUNER >
ANT. Input ---------------------- 75 ohm Unbal., F type
Reference Level--------------- 20 Vp-p (LCD Green Cathode)
Test Input Signal -------------- 400 Hz 30% modulation
Description
Condition
Unit
Nominal
Limit
1. Intermediate Freq.
Picture
Sound
MHz
MHz
45.75
41.25
-----
2. Color Killer Sens.
CH-2
CH-10
CH-55
dBV
dBV
dBV
17
17
17
23
23
23
---
MHz
2.4
2.1
Condition
Unit
Nominal
Limit
Horizontal
Vertical
pixels
pixels
1280 3
720
-----
cd/m2
550
---
3. AFT Pull In Range (10 mV input)
< LCD PANEL >

Description
1. Number of Pixels
2. Brightness
3. Response Time (tr+tf)
---
msec
25
---
4. Support Color
---
16.7 mil. (8 bit)
---
5. Viewing Angle
Horizontal
Vertical
-85 to 85
-85 to 85
-----
Condition
Unit
Nominal
Limit
Horizontal
Vertical
%
%
5
5
-----
--x
y
12000
0.272
0.278
--0.03
0.03
Horizontal
Vertical
line
line
400
350
-----
< VIDEO >

Description
1. Over Scan
2. Color Temperature
3. Resolution
< AUDIO >

All items are measured across 8 load at speaker output terminal with L.P.F.
Description
1. Audio Output Power
2. Audio Distortion
3. Audio Freq. Response
Condition
Unit
Nominal
Limit
10% THD: Lch/Rch
5.0/5.0
4.5/4.5
500mW: Lch/Rch
1.0/1.0
4.0/4.0
-6dB: Lch
-6dB: Rch
Hz
Hz
100 to 10 k
100 to 10 k
-----
Note: Nominal specifications represent the design specifications. All units should be able to approximate these.
Some will exceed and some may drop slightly below these specifications. Limit specifications represent
the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet
limit specifications.
1-1
L4300SP
IMPORTANT SAFETY PRECAUTIONS

Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical
codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally
important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV

Circuit
d. Leakage Current Hot Check - With the

instrument completely reassembled, plug the
AC line cord directly into a 120 V AC outlet. (Do
not use an isolation transformer during this
test.) Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI) C101.1
Leakage Current for Appliances and
Underwriters Laboratories (UL) 1410, (50.7).
With the instrument AC switch first in the on
position and then in the off position, measure
from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal
cabinet, screw heads, metallic overlays, control
shafts, etc.), especially any exposed metal
parts that offer an electrical return path to the
chassis. Any current measured must not
exceed 0.5 milli-ampere. Reverse the
instrument power cord plug in the outlet and
repeat the test.
1. Before returning an instrument to the

customer, always make a safety check of the
entire instrument, including, but not limited to, the
following items:
a. Be sure that no built-in protective devices are
defective and have been defeated during
servicing. (1) Protective shields are provided
on this chassis to protect both the technician
and the customer. Correctly replace all missing
protective shields, including any removed for
servicing convenience. (2) When reinstalling
the chassis and/or other assembly in the
cabinet, be sure to put back in place all
protective devices, including but not limited to,
nonmetallic control knobs, insulating
fishpapers, adjustment and compartment
covers/shields, and isolation resistor/capacitor
networks. Do not operate this instrument or
permit it to be operated without all
protective devices correctly installed and
functioning. Servicers who defeat safety
features or fail to perform safety checks
may be liable for any resulting damage.
READING SHOULD
NOT BE ABOVE 0.5 mA
DEVICE
BEING
TESTED
b. Be sure that there are no cabinet openings

through which an adult or child might be able to
insert their fingers and contact a hazardous
voltage. Such openings include, but are not
limited to, (1) spacing between the Liquid
Crystal Panel and the cabinet mask, (2)
excessively wide cabinet ventilation slots, and
(3) an improperly fitted and/or incorrectly
secured cabinet back cover.
LEAKAGE
CURRENT
TESTER
TEST ALL EXPOSED

METAL SURFACES
ALSO TEST WITH

PLUG REVERSED
USING AC
ADAPTER PLUG
AS REQUIRED
c. Antenna Cold Check - With the instrument AC

plug removed from any AC source, connect an
electrical jumper across the two AC plug
prongs. Place the instrument AC switch in the
on position. Connect one lead of an ohmmeter
to the AC plug prongs tied together and touch
the other ohmmeter lead in turn to each tuner
antenna input exposed terminal screw and, if
applicable, to the coaxial connector. If the
measured resistance is less than 1.0 megohm
or greater than 5.2 megohm, an abnormality
exists that must be corrected before the
instrument is returned to the customer. Repeat
this test with the instrument AC switch in the off
position.
EARTH
GROUND
ANY MEASUREMENTS NOT WITHIN THE

LIMITS SPECIFIED HEREIN INDICATE A
POTENTIAL SHOCK HAZARD THAT MUST
BE ELIMINATED BEFORE RETURNING THE
INSTRUMENT TO THE CUSTOMER OR
BEFORE CONNECTING THE ANTENNA OR
ACCESSORIES.
2. Read and comply with all caution and safetyrelated notes on or inside the receiver cabinet, on
the receiver chassis, or on the Liquid Crystal
Panel.
2-1
LTVN_ISP
7. Product Safety Notice - Some electrical and

mechanical parts have special safety-related
characteristics which are often not evident from
visual inspection, nor can the protection they give
necessarily be obtained by replacing them with
components rated for higher voltage, wattage, etc.
Parts that have special safety characteristics are
identified by a # on schematics and in parts lists.
Use of a substitute replacement that does not
have the same safety characteristics as the
recommended replacement part might create
shock, fire, and/or other hazards. The product's
safety is under review continuously and new
instructions are issued whenever appropriate.
Prior to shipment from the factory, our products
are strictly inspected to confirm they comply with
the recognized product safety and electrical codes
of the countries in which they are to be sold.
However, in order to maintain such compliance, it
is equally important to implement the following
precautions when a set is being serviced.
3. Design Alteration Warning - Do not alter or add

to the mechanical or electrical design of this TV
receiver. Design alterations and additions,
including, but not limited to circuit modifications
and the addition of items such as auxiliary audio
and/or video output connections, might alter the
safety characteristics of this receiver and create a
hazard to the user. Any design alterations or
additions will void the manufacturer's warranty and
may make you, the servicer, responsible for
personal injury or property damage resulting
therefrom.
4. Hot Chassis Warning a. Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord and maybe safety-serviced without
an isolation transformer only if the AC power
plug is inserted so that the chassis is
connected to the ground side of the AC power
source. To confirm that the AC power plug is
inserted correctly, with an AC voltmeter,
measure between the chassis and a known
earth ground. If a voltage reading in excess of
1.0V is obtained, remove and reinsert the AC
power plug in the opposite polarity and again
measure the voltage potential between the
chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V
AC(RMS) between chassis and earth ground
regardless of the AC plug polarity. This chassis
can be safety-serviced only with an isolation
transformer inserted in the power line between
the receiver and the AC power source, for both
personnel and test equipment protection.
c. Some TV receiver chassis have a secondary
ground system in addition to the main chassis
ground. This secondary ground system is not
isolated from the AC power line. The two
ground systems are electrically separated by
insulation material that must not be defeated or
altered.
5. Observe original lead dress. Take extra care to
assure correct lead dress in the following areas: a.
near sharp edges, b. near thermally hot parts-be
sure that leads and components do not touch
thermally hot parts, c. the AC supply, d. high
voltage, and, e. antenna wiring. Always inspect in
all areas for pinched, out of place, or frayed wiring.
Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to
have overheated or are otherwise damaged
should be replaced with components, parts, or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.
2-2
LTVN_ISP
Precautions during Servicing

A. Parts identified by the # symbol are critical for
safety.
Replace only with part number specified.
L. When connecting or disconnecting the internal

connectors, first, disconnect the AC plug from the
AC supply outlet.
B. In addition to safety, other parts and assemblies

are specified for conformance with regulations
applying to spurious radiation. These must also be
replaced only with specified replacements.
Examples: RF converters, RF cables, noise
blocking capacitors, and noise blocking filters, etc.
M. When installing parts or assembling the cabinet

parts, be sure to use the proper screws and
tighten certainly.
C. Use specified internal wiring. Note especially:

1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components
(transformers, power cord, etc.), wrap ends of
wires securely about the terminals before
soldering.
F. Observe that the wires do not contact heat
producing parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp
edged or pointed parts.
H. When a power cord has been replaced, check that
5~6 kg of force in any direction will not loosen it.
I.
Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder

droplets, etc.) do not remain inside the set.
K. Crimp type wire connector
The power transformer uses crimp type
connectors which connect the power cord and the
primary side of the transformer. When replacing
the transformer, follow these steps carefully and
precisely to prevent shock hazards.
Replacement procedure
1) Remove the old connector by cutting the wires
at a point close to the connector.
Important: Do not re-use a connector (discard
it).
2) Strip about 15 mm of the insulation from the
ends of the wires. If the wires are stranded,
twist the strands to avoid frayed conductors.
3) Align the lengths of the wires to be connected.
Insert the wires fully into the connector.
4) Use the crimping tool to crimp the metal sleeve
at the center position. Be sure to crimp fully to
the complete closure of the tool.
2-3
LTVN_ISP
Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and
wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified
values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm
specified clearance distance (d) and (d') between
soldered terminals, and between terminals and
surrounding metallic parts. (See Fig. 1)
Chassis or Secondary Conductor

Primary Circuit
Table 1: Ratings for selected area

AC Line Voltage
Region
Clearance
Distance (d), (d)
110 to 130 V
U.S.A. or
Canada
3.2 mm
(0.126 inches)
d'
Note: This table is unofficial and for reference only. Be

sure to confirm the precise values.
Fig. 1
2. Leakage Current Test

Confirm the specified (or lower) leakage current
between B (earth ground, power cord plug prongs) and
externally exposed accessible parts (RF terminals,
antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.) is
lower than or equal to the specified value in the table
below.
Exposed Accessible Part

Z
AC Voltmeter
(High Impedance)
Measuring Method: (Power ON)

Insert load Z between B (earth ground, power cord plug
prongs) and exposed accessible parts. Use an AC
voltmeter to measure across both terminals of load Z.
See Fig. 2 and following table.
Earth Ground
Power Cord Plug Prongs
Fig. 2
Table 2: Leakage current ratings for selected areas

AC Line Voltage
Region
Load Z
Leakage Current (i)
Earth Ground (B) to:
110 to 130 V
U.S.A. or
Canada
0.15 F CAP. & 1.5 k

RES. Connected in parallel
i 0.5 mA rms
Exposed accessible
parts
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2-4
LTVN_ISP
STANDARD NOTES FOR SERVICING

Circuit Board Indications
How to Remove / Install Flat Pack-IC
1. The output pin of the 3 pin Regulator ICs is

indicated as shown.
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
Top View
Out
1. Prepare the hot-air flat pack-IC desoldering

machine, then apply hot air to the Flat Pack-IC
(about 5 to 6 seconds). (Fig. S-1-1)
Bottom View
In
Input
2. For other ICs, pin 1 and every fifth pin are

indicated as shown.
5
Pin 1
10
3. The 1st pin of every male connector is indicated as
shown.
Fig. S-1-1
2. Remove the flat pack-IC with tweezers while
applying the hot air.
Pin 1
3. Bottom of the flat pack-IC is fixed with glue to the

CBA; when removing entire flat pack-IC, first apply
soldering iron to center of the flat pack-IC and heat
up. Then remove (glue will be melted). (Fig. S-1-6)
Pb (Lead) Free Solder
4. Release the flat pack-IC from the CBA using

tweezers. (Fig. S-1-6)
Pb free mark will be found on PCBs which use Pb

free solder. (Refer to figure.) For PCBs with Pb free
mark, be sure to use Pb free solder. For PCBs
without Pb free mark, use standard solder.
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use
an appropriate hot-air flat pack-IC desoldering
machine, whose shape matches that of the Flat
Pack-IC.
2. Do not supply hot air to the chip parts around the
flat pack-IC for over 6 seconds because damage
to the chip parts may occur. Put masking tape
around the flat pack-IC to protect other parts from
damage. (Fig. S-1-2)
Pb free mark
3-1
TVN_SN
With Soldering Iron:
3. The flat pack-IC on the CBA is affixed with glue, so

be careful not to break or damage the foil of each
pin or the solder lands under the IC when
removing it.
CBA
1. Using desoldering braid, remove the solder from

all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)
Hot-air
Flat Pack-IC
Desoldering
Machine
Flat Pack-IC
Desoldering Braid
Soldering Iron
Masking
Tape
Tweezers
Flat Pack-IC
Fig. S-1-3
2. Lift each lead of the flat pack-IC upward one by
one, using a sharp pin or wire to which solder will
not adhere (iron wire). When heating the pins, use
a fine tip soldering iron or a hot air desoldering
machine. (Fig. S-1-4)
Fig. S-1-2
Sharp
Pin
Fine Tip
Soldering Iron
Fig. S-1-4

3-2
TVN_SN
With Iron Wire:
2. Installation

all pins of the flat pack-IC. When you use solder
flux which is applied to all pins of the flat pack-IC,
you can remove it easily. (Fig. S-1-3)

the foil of each pin of the flat pack-IC on the CBA
so you can install a replacement flat pack-IC more
easily.
2. Affix the wire to a workbench or solid mounting

point, as shown in Fig. S-1-5.
2. The mark on the flat pack-IC indicates pin 1.

(See Fig. S-1-7.) Be sure this mark matches the 1
on the PCB when positioning for installation. Then
presolder the four corners of the flat pack-IC. (See
Fig. S-1-8.)
3. While heating the pins using a fine tip soldering

iron or hot air blower, pull up the wire as the solder
melts so as to lift the IC leads from the CBA
contact pads as shown in Fig. S-1-5.
3. Solder all pins of the flat pack-IC. Be sure that

none of the pins have solder bridges.

Example :

Note: When using a soldering iron, care must be
taken to ensure that the flat pack-IC is not
being held by glue. When the flat pack-IC is
removed from the CBA, handle it gently
because it may be damaged if force is applied.
Pin 1 of the Flat Pack-IC

is indicated by a " " mark.
Hot Air Blower
or
Fig. S-1-7
Presolder
Iron Wire
Soldering Iron
To Solid
Mounting Point
Fig. S-1-5
Flat Pack-IC
CBA
CBA
Fig. S-1-8
Fine Tip
Soldering Iron
Flat Pack-IC
Tweezers
Fig. S-1-6
3-3
TVN_SN
Instructions for Handling Semiconductors

Electrostatic breakdown of the semi-conductors may
occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body

Be sure to wear a grounding band (1 M) that is
properly grounded to remove any static electricity that
may be charged on the body.
2. Ground for Workbench

Be sure to place a conductive sheet or copper plate
with proper grounding (1 M) on the workbench or
other surface, where the semi-conductors are to be
placed. Because the static electricity charge on
clothing will not escape through the body grounding
band, be careful to avoid contacting semi-conductors
with your clothing.
<Incorrect>
CBA
<Correct>
Grounding Band
1M
CBA
1M
Conductive Sheet or
Copper Plate
3-4
TVN_SN
CABINET DISASSEMBLY INSTRUCTIONS

1. Disassembly Flowchart
Removal
Step/
Loc.
No.
This flowchart indicates the disassembly steps for the

cabinet parts, and the CBA in order to gain access to
item(s) to be serviced. When reassembling, follow the
steps in reverse order. Bend, route and dress the
cables as they were.
[1] Stand Base
Plate
[2] Stand Hinge
[17] Speaker (R)
[3] Stand Cover
[4] Rear Cabinet
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
Note
[8]
Jack
Holder(A)
D2 4(S-9)
---
[9]
Shield Box
D2 6(S-10), (N-1)
---
4(S-11), *CN151,
*CN253, *CN1111,
D3
*CN1112, *CN1113,
*CN1116
---
[10] Main CBA

[18] Speaker (L)
[11]
[7] Jack Holder(D)
Part
[5] Function CBA
Digital Main
D3 4(S-12), *CN1121
CBA Unit
---
6(S-13), *CN1050,
*CN1100, *CN1150,
D3
*CN1150, *CN1200,
*CN1250, CN1300
[9] Shield Box
[6] Chassis Bracket
[16] LED CBA
Inverter
[12]
CBA
[11] Digital Main

CBA Unit
[8] Jack Holder(A)
[12] Inverter CBA
[13] PCB Holder D3 3(S-14), 2(S-15)
---
6(S-16), 5(S-17),
4(S-18)
---
[10] Main CBA
[13] PCB Holder
[14]
Panel
Holder
D4
[15]
LCD
Module
D4 ---------------
[16] LED CBA
[14] Panel Holder
Removal
Step/
Loc.
No.
Part
Fig.
No.
Remove/*Unhook/
Unlock/Release/
Unplug/Unclamp/
Desolder
3(S-19), *CN803,
*CN804
-----
[18] Speaker (L) D4 4(S-21)
---
[19] Front Cabinet
2. Disassembly Method
Speaker
(R)
---
D4 4(S-20)
[17]
[15] LCD Module
D4
---
[19]
Front
Cabinet
(1)
(2)
D4 ---------------
---
(3)
(5)
(4)
Note:
(1) Order of steps in procedure. When reassembling,
follow the steps in reverse order. These numbers
are also used as the Identification (location) No. of
parts in figures.
Note
[1]
Stand Base
2(S-1A), 4(S-1B),
D1
Plate
6(S-2), 5(S-3)
---
[2]
Stand
Hinge
D1 ---------------
---
[3]
Stand
Cover
D1 ---------------
---
[4]
Rear
Cabinet
D1 8(S-4), 4(S-5)
---
[5]
Function
CBA
D1 3(S-6), *CN1505
---
[6]
Chassis
Bracket
D2 10(S-7)
---
[7]
Jack
Holder(D)
D2 (S-8)
---
(2) Parts to be removed or installed.

(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked,
unlocked, released, unplugged, unclamped, or
desoldered.
N = Nut, L = Locking Tab, S = Screw,
CN = Connector
* = Unhook, Unlock, Release, Unplug, or Desolder
e.g. 2(S-2) = two Screws (S-2),
2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the
Table."
4-1
L4400DC
S-4
S-4
S-6
[5] Function CBA

S-5
S-4
[4] Rear Cabinet
S-1A
S-4
S-1B
S-1B
S-4
[3] Stand Cover
[2] Stand Hinge

[1] Stand Base Plate
S-2
S-3
S-2
4-2
S-3
S-2
Fig. D1
L4400DC
[8] Jack Holder(A)

[6] Chassis Bracket
S-7
S-9
S-7
S-10
[9] Shield Box
S-7
S-10
S-7
N-1
[7] Jack Holder(D)

S-8
Fig. D2
4-3
L4400DC
S-13
[12] Inverter CBA

S-14
S-11
S-15
[13] PCB Holder

S-15
S-12
[11] Digital Main CBA Unit
[10] Main CBA
Fig. D3
4-4
L4400DC
[14] Panel Holder
[19] Front Cabinet
S-18
S-16
[17] Speaker (R)
S-18
S-17
S-17
S-16
S-20
S-16
S-19
[16] LED CBA
S-16
S-21
[18] Speaker (L)
S-17
[15] LCD Module

S-18
S-17
S-16
S-18
[14] Panel Holder

S-16
4-5
S-17
Fig. D4
L4400DC
TV Cable Wiring Diagram

To LCD
Module
Inverter CBA
CN1050
CN1150
CN1250
CN1100
CN1200
CN1300
Function CBA
CN101
CN1000
To LCD
Module
Main CBA
Digital Main
CBA Unit
CN1121
CN253
CN1505
CN111
CN1111
CN1112
CN112
CN1116
CN113
CN1113
CN114
CN151A
CN804
CN803
LED CBA
CN151
To Speaker
Fig. D5
4-6
L4400DC
ELECTRICAL ADJUSTMENT INSTRUCTIONS

How to set up the service mode:
General Note: CBA is abbreviation for

Circuit Board Assembly.
Service mode:
Note: Electrical adjustments are required after

replacing circuit components and certain
mechanical parts. It is important to perform
these adjustments only after all repairs and
replacements have been completed.
Also, do not attempt these adjustments unless
the proper equipment is available.
1. Use the service remote control unit.

2. Turn the power on. (Use main power on the TV
unit.)
3. Press [SLEEP] button on the service remote
control unit. The following screen appears.
"*" differs depending on the models.
Test Equipment Required

Host Ver.
Boot
System
Sub Ver.
1. DC Voltmeter
2. NTSC Pattern Generator (Color Bar W/White
Window, Red Color, Dot Pattern, Gray Scale,
Monoscope, Multi-Burst)
3. Remote control unit: Part No. N0105UD or
N0127UD
: *********
: Push 0 key
: Push 0 key
: *********
Calibration Check
OK
4. Color Analyzer
How to make Service remote

control unit:
1. Prepare normal remote control unit.
(Part No. N0105UD or N0127UD)
Remove 3 Screws from the back lid. (Fig. 1-1)
Screws
Remote control unit (bottom)
Fig. 1-1
J1
2. Add J1 (Jumper Wire) to the remote control CBA.

(Fig. 1-2)
Remote Control CBA
Fig. 1-2
5-1
L4400EA
1. Purity Check Mode
The following adjustment normally are not

attempted in the field. Only when replacing the
LCD Panel then adjust as a preparation.
This mode cycles through full-screen displays of red,

green, blue, and white to check for non-active pixels.
2. White Balance Adjustment
1. Enter the Service mode.
*This adjustment is needed when reparing T-CON

CBA.
2. Each time pressing [7] button on the service

remote control unit, the display changes as
follows.
Purpose: To mix red, green and blue beams correctly

for pure white.
Purity Check Mode
Symptom of Misadjustment: White becomes bluish

or reddish.
Red mode
Test Point Adj. Point
Mode
Input
[7] button
Screen
VOL. p
buttons
[RF/VIDEO1]
C/D
[7] button
Green mode
White Purity
(APL 80%)
or
(APL 20%)
M. EQ.
Spec.
Pattern Generator,
Color analyzer
x: 0.256 to 0.316,
y: 0.264 to 0.324
Figure
[7] button
It carries out in a darkroom.
Blue mode
Perpendicularity
[7] button
L = 3 cm
White mode
INPUT: WHITE 80%
Color Analyzer
Note: Use service remote control unit

1. Operate the unit for more than 20 minutes.
2. Input the White Purity (APL 80% or APL 20%).
3. Set the color analyzer to the CHROMA mode and
bring the optical receptor to the center on the
LCD-Panel surface after zero point calibration as
shown above.
Note: The optical receptor must be set
perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL p] button on
the remote control unit and select C/D mode.
5. When x value and y value are not within
specification, adjust DB (C/D) or DR (C/D).
Refer to 1. Initial Setting.
Note: DB(C/D) or DR(C/D) must be adjusted
within 0.01.
6. Turn the power off and on again. (Main power
button on the TV unit.)
5-2
L4400EA
3. Auto Calibration
4. Flicker Adjustment
Purpose: To bring the color adjustment of each

component into standard alignment.
*This adjustment is needed when reparing T-CON

CBA.
Symptom of Misadjustment: The color adjustment

differs from component to component.
1. Enter the Service mode. (See page 5-1.)

2. Press [2] button on the remote control unit.
The following screen appears.
1. Input white raster signal (10%=10 IRE, 100%=100

IRE) from Component 1 Y jack.
2. Enter the service mode.
3. To enter the Auto Calibration adjustment mode,
press [6] button on the service remote control unit.
4. To start auto adjustment, press [CH o] button on
the service remote control unit.
- In the auto adjustment mode, Calibration Check
appears on the screen.
- Upon completion, Calibration Check OK and
Push FCH UP key appear on the screen.
3. If Flicker Adjustment is not fit, the screen become
the following.
- If the auto adjustment failure, Calibration Check

NG and Push FCH UP key appear on the
screen.
5. Unplug AC cord and plug it in AC outlet again to
reset then enter the service mode again.
FLASH (Go and Off)

4. Turn the VR1 on the LCD Module so that flash
stops.
5-3
L4400EA
HOW TO INITIALIZE THE LCD TELEVISION

How to initialize the LCD television:
1. To turn the power on, press [POWER] button on
the normal remote control unit or the unit.
2. Use the service remote control unit. (Refer to
ELECTRICAL ADJUSTMENT INSTRUCTIONS
section.
3. To enter the service mode, press [SLEEP] button
on the service remote control unit.
- To cancel the service mode, press [TV POWER]
button on the remote control.
4. To initialize the LCD television, press [DISPLAY]
button on the normal remote control unit.
- INITIALIZED (red) appears on the screen.
- After few seconds (completion initialization), the
screen is reset.
6-1
L4300INT
SCL 82
SDA 83
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
IC1102 (MEMORY)
7-1
7
6
5
+3.3V
RESET
IC1104
X1102
55.474MHz
OSC
X1101
25.14MHz
OSC
I2C-CLK-A
I2C-DATA-A
WP
SCL
SDA
SCL 14
SDA 15
TU1001 (TUNER UNIT)
SCL 69
SDA 66
IC1507 (LVDS TRANSMITTER)
IC1401 (HDMI /IF)
XOUT
XIN
B14 RESET
F28
F27
D20 XOUT
D21 XIN
C11 EPROM-WP
AG20 I2C-CLK-A
AK21 I2C-DATA-A
H2
AK8
D17
C17
B17
AG12
RXD AJ21
TXD AH21
BACKLIGHT-SW
AMP-MUTE
AUDIO-SW0
AUDIO-SW1
AUDIO-SW2
AUDIO-MUTE
C16 I2C-CLK-TUNER
D16 I2C-DATA-TUNER
AJ20 I2C-CLK-C
AH20 I2C-DATA-C
IC1504
(MAIN MICRO CONTROLLER)
AUDIO-MUTE
VOLUME 56
P-ON-H 26
PROTECT1
+5V
TO AUDIO
BLOCK DIAGRAM
X1501
4MHz
OSC
XOUT 23
XIN 22
RESET
IC1503
CN1113
19 REMOTE
20 LED1
21 LED2
RESET 19
KEY-IN1 3
KEY-IN3 60
BACKLIGHT-ADJ
DIGITAL MAIN CBA UNIT
14 TXD1
15 RXD1
REMOTE 17
LED1 32
LED2 31
IC1502
(SUB MICRO CONTROLLER)
CN1112
1
3
18
16
20
21
22
CN112
PROTECT1 23
P-ON-H
21
VOLUME
6
AMP-MUTE 8
AUDIO-SW0 4
AUDIO-SW1 3
AUDIO-SW2 2
CN1111
CN111
1 BACKLIGHT-SW 23
2 BACKLIGHT-ADJ 22
CN1505
3 KEY-IN1
1 KEY-IN3
CN101
3
5
CN151A
2 REMOTE
4 LED1
5 LED2
MAIN CBA
CN114
5
4
3
KEY SWITCH
KEY SWITCH
STBY+3.3V
TO AUDIO
BLOCK DIAGRAM
TO POWER SUPPLY
BLOCK DIAGRAM
MAIN CBA
PROTECT1
P-ON-H
VOLUME
AMP-MUTE
AUDIO-SW0
AUDIO-SW1
AUDIO-SW2
BACKLIGHT-SW
BACKLIGHT-ADJ
PROTECT1
STBY
P-ON
TO INVERTER
BLOCK DIAGRAM
LED CBA
D152
D151
REMOTE
SENSOR
FUNCTION CBA
CN151
2
4
5
RCV151
System Control Block Diagram
BLOCK DIAGRAMS
L4400BLS
7-2
VIDEO-Pr-IN2
VIDEO-Pb-IN2
VIDEO-Y-IN2
VIDEO-Pr-IN1
VIDEO-Pb-IN1
VIDEO-Y-IN1
S-VIDEO-IN2
S-VIDEO-IN1
VIDEO-IN2
VIDEO-IN1
1 2
1 2
JK704
JK703
JK702
JK701
BUFFER
Q712
BUFFER
Q711
BUFFER
Q710
BUFFER
Q709
BUFFER
Q708
BUFFER
Q707
BUFFER
Q706
BUFFER
Q705
BUFFER
Q704
BUFFER
Q703
BUFFER
Q702
BUFFER
Q701
MAIN CBA
WF5
WF4
WF3 WF2
WF1
CN1116
22
17
20
19
16
15
7
9
4
6
1
3
10
12
JK1401
CN1113
S-VIDEO-Y-IN1 3
S-VIDEO-C-IN1 2
VIDEO-Y-IN1
13
VIDEO-Pb-IN1 11
VIDEO-Pr-IN1
10
VIDEO-Y-IN2
8
VIDEO-Pb-IN2
6
VIDEO-Pr-IN2
5
VIDEO-IN1
VIDEO-IN2
S-VIDEO-Y-IN2
S-VIDEO-C-IN2
HDMI-DATA
HDMI-CLOCK
DATA 0(+)
DATA 0(-)
DATA 1(+)
HDMI-IN
DATA 1(-)
DATA 2(+)
DATA 2(-)
CLOCK(+)
CLOCK(-)
WF6
CN114
21
22
11
13
14
16
18
19
CN113
2
7
4
5
BUFFER
Q1402
BUFFER
Q1401
IC1402 (HDMI MEMORY)
35
34
38
37
41
40
43
44
74
68
79
71
66
77
49
50
CLAMP
HDMI
RECEIVER
MUX
IIC
I/F
A/D
IC1401 (HDMI INTERFACE)
6 SCL
5 SDA
MUX
AUDIO
DECODER
MATRIX
22
23
27
20
19
12
99
92
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
AUDIO SIGNAL
HDMI BCLK
HDMI LRCLK TO DIGITAL
SIGNAL PROCESS
HDMI SDATA
BLOCK DIAGRAM
DAC-OSCLK
B DATA(0-7)
G DATA(0-7)
R DATA(0-7)
S-VIDEO-C-IN2
S-VIDEO-C-IN1
S-VIDEO-Y-IN2
S-VIDEO-Y-IN1
VIDEO-IN1
VIDEO-IN2
VIDEO SIGNAL
Video Input Block Diagram
L4400BLVIN
TO VIDEO
BLOCK DIAGRAM
VIDEO 4
(ANALOG)
IF-AGC 18
IF1 21
IF2 20
TU1001
(TUNER UNIT)
7-3
P1,
R2-4,
T1,U2-4
U1,
V1-4,
W1-3
G-DATA(0-7)
B-DATA(0-7)
M1,
N1-4,
P2-4
B26
D26
C29
D30
D28
C25
A25
B15
A28
A27
R-DATA(0-7)
S-VIDEO-Y-IN1
S-VIDEO-C-IN1
S-VIDEO-Y-IN2
S-VIDEO-C-IN2
VIDEO-IN1
VIDEO-IN2
BUFFER
Q1002
SAW
FILTER
ANALOG
SW
DEMODU
-LATOR
A/D
CONVERTER
MPEG
DECODER
IC1504 (DIGITAL SIGNAL PROCESS)
DIGITAL
SIGNAL
PROCESS
AUDIO
INTERFACE
59
61
60
20-23,
26-29,
37-42,
45,46,
49-56
PLL
LVDS
TX
DAC-OSCLK
HDMI-BCLK
HDMI-LRCLK
HDMI-SDATA
AD-DATA
DAC-BCLK
DAC-LRCLK
DAC-OSCLK
DAC-DATA
SPDIF
AK4
AJ6
AK5
AJ5
AH10
AK9
AJ10
AG11
AJ9
AG23-27,
AH24,AH25,
AH27,AH28,
AH30,AJ24,AJ25,
AJ28,AJ29,
AK25,AK27
P27,P28,
R27,R28,R30,
T27-29,V27-29,
W27,U27-30
AB27,AB28,
AC27-30,
AD27-30,
AE27,AE28,AE30
H28,
J29,J30,
K29,K30,
L29,L30
M29
IC1105 (SDRAM)
IC1110 (SDRAM)
ADDESS(0-12)
ADDESS(0-12)
TO AUDIO
BLOCK DIAGRAM
TO VIDEO
BLOCK DIAGRAM
28-32,
35-42
2,4,5,7,8,10,
11,13,54,56,
57,59,60,62, DATA(0-15)
63,65
28-32,
35-42
TX0(+)
TX0(-)
TX1(+)
TX1(-)
TX2(+)
TX2(-)
TX3(+)
TX3(-)
TXCLK(+)
TXCLK(-)
I2C-CLK-A
I2C-DATA-A
AUDIO SIGNAL
LCD MODULE
IC1108 (FLASH MEMORY)
CN1121
4
3
8
7
12
11
20
19
16
15
27
29
29-32, DATA(0-7)
41-44
75
74
77
76
81
80
85
84
83
82
2,4,5,7,8,10,
11,13,54,56,
57,59,60,62, DATA(0-15)
63,65
IC1507 (LVDS TRANSMITTER)
TO SYSTEM CONTROL I2C-CLK-A

BLOCK DIAGRAM
I2C-DATA-A
CLOCK AD16
V-SYNC AK15
H-SYNC AJ15
AG13-18,
AH12-14,
AH16-18,
AJ12-14,
AJ17-19,
AK12-14,
AK17-19
VIDEO SIGNAL
Video Block Diagram
L4400BLV
7-4
JK704
JK703
TO SYSTEM
CONTROL
BLOCK DIAGRAM
AUDIO(R)
-IN4
AUDIO(L)
-IN4
AUDIO(R)
-IN3
AUDIO(L)
-IN3
AUDIO(R)
-IN2
AUDIO(L)
-IN2
AUDIO(R)
-IN1
AUDIO(L)
-IN1
JK701
AUDIO-SW0
AUDIO-SW1
AUDIO-SW2
Q453
Q452
Q451
MAIN CBA
CN113
13
12
16
15
9 10 11
SW CTL
INPUT
SELECT
SW
CN1116
11
12
8
9
9 10 11
SW CTL
INPUT
SELECT
SW
Q1006
BUFFER
Q1007
BUFFER
Q1012
DRIVE
Q1009
BUFFER
Q1008
BUFFER
Q1011
MUTE-ON
(L-CH)
30
MTS/SAP
AUDIO SIGNAL
PROCESS
29
(R-CH)
21
SAW
FILTER
FL1002
IC1002
(MTS/SAP AUDIO SIGNAL PROCESS)
Q1515
BUFFER
IC1053
(OP AMP)
HDMIAUDIO(R)
-IN
HDMIAUDIO(L)
-IN
AUDIO(L)
-OUT
AUDIO(R)
-OUT
3 SIF
TU1001(TUNER UNIT)
JK1405
JK1405
14
15
1
2
11
10
15
12
Q1509
BUFFER
4
7
8
5
6
IC1111 (BUFFER)
D/A
CONVERTER
IC1052 (AUDIO D/A CONVERTER)
A/D
CONVERTER
CN151A
7
9
8
10
WF7
SP(L)
SP-GND
SP(R)
SP-GND
Q802
MUTE
CN803
CLN803
SP(R) 1
SP-GND 2
CLN804
CN804
SP(L) 1
SP-GND 2
LED CBA
AMP-MUTE
VOLUME
VOLUME
AMP
AMP
12
SP802
SPEAKER
R-CH
SP801
SPEAKER
L-CH
TO DIGITAL
SIGNAL PROCESS
BLOCK DIAGRAM
AUDIO SIGNAL
DAC-DATA
SPDIF
DAC-BCLK
DAC-LRCLK
DAC-OSCLK
AD-DATA
IC801 (AUDIO AMP)
CN151
7
9
8
10
TO SYSTEM CONTROL
BLOCK DIAGRAM
CN113
CN1116
2 AUDIO(L)-1 22
3 AUDIO(R)-1 21
JK1403
DIGITAL
AUDIO-OUT
(COAXIAL)
Q1010
MUTE-ON
Q1014
BUFFER
Q1013
BUFFER
Q1516
BUFFER
CN113
CN1116
19 AUDIO(L)-2 5
18 AUDIO(R)-2 6
TO SYSTEM CONTROL AUDIO-MUTE

BLOCK DIAGRAM
IC451 (INPUT SELECT)
HDMI-AUDIO(L)-IN
HDMI-AUDIO(R)-IN
TUNER-AUDIO(L)
TUNER-AUDIO(R)
13
14
1
5
2
15
13
14
1
5
2
15
IC452 (INPUT SELECT)
IC1051 (AUDIO A/D CONVERTER)
Audio Block Diagram
L4400BLA
7-5
Q1001
Q1003
Q1002
10
CN253
1-8
19
20
18
HF OSC
OUTPUT
DRIVE
CONTROL
LOGIC
13
12
9
10
6
5
14
2
3
13
12
9
10
6
5
14
VCC 4
IC1550 (COMPARATOR)
2
3
VCC 4
13
15
LOGIC
LOGIC
V-REF
V-REF
V-REF
13
12
1
8
15
14
10
11
Q1000
+5V
REG.
INVERTER CBA
VDD
VDD
DRIVE
DRIVE
DRIVE
DRIVE
IC1001 (DRIVER)
CN1000
INV+24V
13-20
BACKLIGHT-ADJ 2
BACKLIGHT-SW 1
PROTECT1
3
IC1500 (COMPARATOR)
IGNITION
/PROTECTION
CONTROL
LOGIC
LF OSC
SW
CTL
IC1000 (INVERTER CONTROL)
INV+24V
BACKLIGHT-ADJ
TO SYSTEM
BACKLIGHT-SW
CONTROL
BLOCK DIAGRAM PROTECT1
MAIN CBA
VS
IS
HDR2
LDR2
HDR1
LDR1
HDR1
LDR1
HDR2
LDR2
DRIVE
Q1250,Q1251
DRIVE
Q1252,Q1253
DRIVE
Q1100,Q1101
DRIVE
Q1102,Q1103
3
4
2
5
1
6
3
4
2
5
1
6
3
4
2
5
1
6
3
4
2
5
1
6
3
4
2
5
1
6
3
4
2
5
1
6
T1300
T1250
T1200
T1150
T1100
T1050
10
10
10
10
10
10
Q1020
CN1300
1
2
CN1250
1
2
CN1200
1
2
CN1150
1
2
CN1100
1
2
CN1050
1
2
LCD MODULE
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
BACK
LIGHT
Inverter Block Diagram
L4400BLIV
AC601
AC CORD
4A 125V
F601
L601
4A/125V
LINE
FILTER
BRIDGE
RECTIFIER
7-6
MAIN CBA
Q631
SWITCHING
Q602
SWITCHING
CONTROL
Q601
SWITCHING
HOT
Q632
SWITCHING
CONTROL
BRIDGE
RECTIFIER
D638 - D641
Q603
LIMIT
D601 - D604
L602
LINE
FILTER
HOT CIRCUIT. BE CAREFUL.
D542
12
11
IC631
D504
10
T631
15
12
IC602
13
10
14
11
IC601
T601
CAUTION !
Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown , check to see that all components in the power supply
circuit are not defective before you connect the AC plug to the AC power supply.
Otherwise it may cause some components in the power supply circuit to fail.
SHUNT
REG
SHUNT
REG
Q535
Q501
COLD
Q534
4A/125V
Q533
IC534
+5V REG
Q536
IC535
+3.3V
REG
IC532
+1.2V REG
IC536
+5V REG
IC533
+1.8V REG
IC531
+2.5V REG
Q531, Q801, Q803

AUDIO+B
REG
Q502
IC537
+3.3V REG
Q537
Q504
P-ON-H
AUDIO+B
+12V
INV+24V
CN111
+1.8V
+2.5V
STBY+3.3V
+33V
+3.3V
+5V
LCD+5V
+1.2V
TO
SYSTEM
PROTECT1 CONTROL
BLOCK
DIAGRAM
TO SYSTEM
CONTROL
BLOCK DIAGRAM
NOTE:
The voltage for parts in hot circuit is measured using
hot GND as a common terminal.
CAUTION ! : For continued protection against risk of fire,

replace only with same type 4 A, 125V fuse.
ATTENTION : Utiliser un fusible de rechange de mme type de 4A, 125V.
19
12,13
2
1
10
4
6,7
16-18
TO
DIGITAL
MAIN CBA
UNIT
(CN1111)
Power Supply Block Diagram
L4400BLP
SCHEMATIC DIAGRAMS / CBA'S AND TEST POINTS

Standard Notes
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often
pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltage, wattage, etc. Replacement parts that have these special safety
characteristics are identified in this manual and its supplements; electrical components having such features are
identified by the mark # in the schematic diagram and the parts list. Before replacing any of these components,
read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same
safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:
1. Do not use the part number shown on these drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in F (P = 10-6 F).
5. All voltages are DC voltages unless otherwise specified.
Note of Capacitors:
ML --- Mylar Cap.
PP --- Metallized Film Cap.
SC --- Semiconductor Cap.
L --- Low Leakage type
Temperature Characteristics of Capacitors are noted with the following:

B --- 10%
CH --- 060 ppm/C
CSL --- +350~-1000 ppm/C
Tolerance of Capacitors are noted with the following:

Z --- +80~-20%
Note of Resistors:
CEM --- Cement Res.
MTL --- Metal Res.
F --- Fuse Res.
Capacitors and transistors are represented by the following symbols.
CBA Symbols
Schematic Diagram Symbols
(Top View) (Bottom View)

+
Electrolytic Capacitor
Digital Transistor
(Bottom View)
Transistor or Digital Transistor

E
(Top View)
(Top View)
NPN Transistor
PNP Transistor
ECB
ECB
(Top View)
(Top View)
PNP Digital Transistor
NPN Digital Transistor

ECB
ECB
8-1
LC4N_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON

THE FOLLOWING PAGES:
1. CAUTION:
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME
TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE_A,_V.
2. CAUTION:
Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit.
If Main Fuse (F601) is blown, first check to see that all components in the power supply circuit are not
defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components
in the power supply circuit to fail.
3. Note:
1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are
listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below:

Plug the TV power cord into a standard AC outlet.:
1
(Unit: Volt)
5.0
Voltage
5.0
Power on mode
Indicates that the voltage

is not consistent here.
5. How to read converged lines

1-D3
3
Distinction Area
Line Number
(1 to 3 digits)
AREA D3
2
Examples:
1. "1-D3" means that line number "1" goes to the line number
1
"1" of the area "D3".
2. "1-B1" means that line number "1" goes to the line number
"1" of the area "B1".
1-B1
AREA B1
1-D3
A
6. Test Point Information

: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
8-2
LC4N_SC
Main 1/5 Schematic Diagram

VOLTAGE CHART
CN112
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0
3.3
3.3
0
0
1.1
0
0.1
0.1
0
0
0
0
0
0
0
0
0
0
3.4
3.2
1.1
2.3
CN114
8-3
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0
3.4
3.4
1.0
3.4
0
0
3.3
3.3
0
1.7
0
1.7
1.6
0
1.6
0
1.7
1.6
0
1.6
1.7
0
L4400SCM1
VOLTAGE CHART
CN113
8-4
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
0
1.6
0
1.7
1.7
0
1.7
0
0.6
0.6
0
6.0
6.0
0
6.0
6.0
0
6.0
5.9
0
5.3
5.4
0
L4400SCM2
VOLTAGE CHART
CN111
8-5
Pin No.
Voltage
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
32.7
3.4
0
5.0
0
5.0
5.0
0
0
3.3
0
2.7
2.7
0
0
1.3
1.3
1.3
1.8
12
0
0
3.3
L4400SCM3
8-6
L4400SCM4

CAUTION !
4A/125V

8-7
NOTE:
L4400SCM5
Function Schematic Diagram
VOLTAGE CHART
CN101
8-8
Pin No.
Voltage
1
2
3
4
5
0
3.4
3.4
3.4
3.4
L4400SCF
LED Schematic Diagram
8-9
L4400SCL
Inverter Schematic Diagram
8-10
L4400SCINV
Digital Main 1/8 Schematic Diagram
8-11
L4400SCD1
8-12
L4400SCD2

1 NOTE:
1. The order of pins shown in this diagram is different from that of actual IC1504.
2. IC1504 is divided into four and shown as IC1504 (1/4) ~ IC1504 (4/4) in this Digital Main Schematic Diagram Section.
8-13
L4400SCD3

1 NOTE:
8-14
L4400SCD4

1 NOTE:
8-15
L4400SCD5
8-16
L4400SCD6

1 NOTE:
8-17
L4400SCD7
8-18
L4400SCD8
Main CBA Top View

CAUTION !
4A/125V

Because a hot chassis ground is present in the power

supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
8-19
BL4300F01011-1
Main CBA Bottom View

CAUTION !
4A/125V

Because a hot chassis ground is present in the power

supply circuit, an isolation transformer must be used.
Also, in order to have the ability to increase the input
slowly,when troubleshooting this type power supply
circuit, a variable isolation transformer is required.
NOTE:
WF1
PIN 2 OF
CN113
WF3
PIN 22 OF
CN114
WF2
PIN 21 OF
CN114
WF6
PIN 14 OF
CN114
WF5
PIN 13 OF
CN114
WF4
PIN 11 OF
CN114
WF7
PIN 8 OF
CN151A
8-20
BL4300F01011-1
Function CBA Top View
Function CBA Bottom View
8-21
BL4300F01011-2
LED CBA Top View
LED CBA Bottom View
8-22
BL4300F01011-3
Inverter CBA Top View
8-23
BL4400F01021
Inverter CBA Bottom View
8-24
BL4400F01021
WAVEFORMS
WF1 ~ WF7 = Waveforms to be observed at
Waveform check points.
(Shown in Schematic Diagram.)
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1
Pin 2 of CN113
CVBS
WF2
0.2V
WF6
20s
0.2V
WF7
AUDIO
0.2V
20s
Pin 14 of CN114
VIDEO-Pr
20s
0.2V
Pin 13 of CN114
VIDEO-Pb
Pin 22 of CN114
VIDEO-C
WF4
20s
Pin 21 of CN114
VIDEO-Y
WF3
WF5
0.2V
20s
Pin 8 of CN151A
0.1V
0.5ms
Pin 11 of CN114
VIDEO-Y
0.2V
20s
9-1
LC4WF
10-1
LCD MODULE
GND
GND
TX0(-)
TX0(+)
GND
GND
TX1(-)
TX1(+)
GND
GND
TX2(-)
TX2(+)
GND
GND
TX-CLK(-)
TX-CLK(+)
GND
GND
TX3(-)
TX3(+)
GND
D+5V-LCD
D+5V-LCD
D+5V-LCD
D+5V-LCD
GND
I2C-CLK-A
GND
I2C-DATA-A
IX-PANEL-CONFIG1
IX-PANEL-CONFIG2
CN1121
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
CN1116
GND
AUDIO(L)-1
AUDIO(R)-1
GND
AUDIO(L)-2
AUDIO(R)-2
GND
TUNER-AUDIO(L)
TUNER-AUDIO(R)
GND
HDMI-AUDIO(L)-IN
HDMI-AUDIO(R)-IN
GND
NU
NU
GND
VIDEO-IN2
GND
S-VIDEO-C-IN2
S-VIDEO-Y-IN2
GND
VIDEO-IN1
GND
CN1113
GND
S-VIDEO-C-IN1
S-VIDEO-Y-IN1
GND
VIDEO-Pr-IN2
VIDEO-Pb-IN2
GND
VIDEO-Y-IN2
GND
VIDEO-Pr-IN1
VIDEO-Pb-IN1
GND
VIDEO-Y-IN1
GND
S-SW1
S-SW2
GND
NU
REMOTE
LED1
LED2
NU
GND
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
CN114
GND
S-VIDEO-C-IN1
S-VIDEO-Y-IN1
GND
VIDEO-Pr-IN2
VIDEO-Pb-IN2
GND
VIDEO-Y-IN2
GND
VIDEO-Pr-IN1
VIDEO-Pb-IN1
GND
VIDEO-Y-IN1
GND
S-SW1
S-SW2
GND
NU
REMOTE
LED1
LED2
NU
GND
CN113
GND
AUDIO(L)-1
AUDIO(R)-1
GND
AUDIO(L)-2
AUDIO(R)-2
GND
TUNER-AUDIO(L)
TUNER-AUDIO(R)
GND
HDMI-AUDIO(L)-IN
HDMI-AUDIO(R)-IN
GND
NU
NU
GND
VIDEO-IN2
GND
S-VIDEO-C-IN2
S-VIDEO-Y-IN2
GND
VIDEO-IN1
GND
MAIN CBA
VIDEO
-Y-IN1
CN112
PROTECT1
PROTECT2
P-ON-H
DVD-PROTECT(NU)
NU
NU
NU
NU
NU
NU
NU
NU
NU
GND
AMP-STBY
AMP-MUTE
GND
VOLUME
GND
AUDIO-SW0
AUDIO-SW1
AUDIO-SW2
GND
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
VIDEO
-IN2
CN111
BACKLIGHT-SW
BACKLIGHT-ADJ
GND
+12V
+1.8V
+1.2V
+1.2V
+1.2V
GND
GND
+2.5V
+2.5V
GND
+3.3V
GND
GND
LCD+5V
LCD+5V
GND
+5V
GND
STBY+3.3V
+33V
VIDEO VIDEO
-Pb-IN1 -Pr-IN1
VIDEO
-Y-IN2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
CN1505
GND
STBY+3.3V
KEY-IN1
KEY-IN2
KEY-IN3
CN1112
PROTECT1
PROTECT2
P-ON-H
DVD-PROTECT(NU)
NU
NU
NU
NU
NU
NU
NU
NU
NU
GND
AMP-STBY
AMP-MUTE
GND
VOLUME
GND
AUDIO-SW0
AUDIO-SW1
AUDIO-SW2
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
CN1000
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
GND
GND
GND
GND
GND
GND
GND
GND
GND
PROTECT1
BACKLIGHT-ADJ
BACKLIGHT-SW
CN101
GND
STBY+3.3V
KEY-IN1
KEY-IN2
KEY-IN3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
10
CN803
SP(R) 1
CLN803
SP-GND 2
INVERTER CBA
SP801
SPEAKER
CN804
L-CH
SP(L) 1
CLN804
SP-GND 2
SP802
SPEAKER
R-CH
FUNCTION CBA
LED CBA
CN151
GND
REMOTE
STBY+3.3V
LED1
LED2
NU
SP(L)
SP(R)
SP-GND
SP-GND
AC601
AC CORD
TU1001 TUNER UNIT
DIGITAL
AUDIO-OUT HDMIHDMIAUDIO(L) AUDIO(R)
(COAXIAL) AUDIO(L)-IN AUDIO(R)-IN -OUT
-OUT
5
4
3
2
1
CN253
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
INV+24V
GND
GND
GND
GND
GND
GND
GND
GND
GND
PROTECT1
BACKLIGHT-ADJ
BACKLIGHT-SW
CN151A
GND 1
REMOTE 2
STBY+3.3V 3
LED1 4
LED2 5
NU 6
SP(L) 7
SP(R) 8
SP-GND 9
SP-GND 10
AUDIO(L) AUDIO(R) AUDIO(L) AUDIO(R) AUDIO(L) AUDIO(R) AUDIO(L) AUDIO(R)

-IN1
-IN3
-IN1
-IN2
-IN2
-IN3
-IN4
-IN4
CN1111
BACKLIGHT-SW
BACKLIGHT-ADJ
GND
+12V
+1.8V
+1.2V
+1.2V
+1.2V
GND
GND
+2.5V
+2.5V
GND
+3.3V
GND
GND
LCD+5V
LCD+5V
GND
+5V
GND
STBY+3.3V
+33V
VIDEO VIDEO
-Pb-IN2 -Pr-IN2
HDMICONNECTOR
S-VIDEO S-VIDEO VIDEO

-IN1
-IN2
-IN1
WIRING DIAGRAM
L4400WI
EXPLODED VIEWS
Cabinet
A1
L2
A3
B16
B13
B13 L5
A2
A5
B13
B13
L1
Function CBA
B1
B13
L1
B13
Inverter CBA
L5
L5
B19
L6
A4
CLN804
L2
B18
B17
B19
L2
L5
L5
SP802
A7
L5
L5
B14
L1
B19
L6
L2
B13
L5
B18
Main CBA
B15 B2
LED CBA
B16
L1
SP801
L2
B9
CLN253
CLN803
L12
LCD1
L4
AC601
L3
L5
L1
L2
L2
B9
L5
L5
L5
A18
B10
L3
L4
B13
L8
L5
A26
L8
B1
B11
L1
L5
A6
L8
A24
L4
L3
Digital Main CBA Unit
L8
B9
B13
B13
L8
B5
L10
L9
L3
See Electrical Parts List

for parts with this mark.
B4
B3
L3
B13
B4
A25
A25
L8
L8
L10
L8
L10
B12
B6
L11
11-1
L4400CEX
Packing
S2
Packing Tape
Some Ref. Numbers are

not in sequence.
Packing Tape
S4
Packing Tape
X2
X3
S6
X4
Tape
S3
X1
Packing Tape
Packing Tape
S5
FR
ON
Packing Tape
S1
11-2
L4400PEX
MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No. Mark
Ref. No. Mark

A1
A1
Mark
A
6632LG
Description
SPEAKER S0516F06
DSD0813XQ002
S1
CARTON L4400UA
S1
CARTON L4401UB
1EM322011
STYROFOAM TOP L4400UA
1EM020875
1EM321391
S3
STYROFOAM BOTTOM L4400UA
1EM020876
S4
SET BAG L4300UA
1EM321546
S5
SERIAL NO. LABEL L9750UA
----------
S6
STAND SHEET L4300UA
1EM423161
X1
Part No.
FRONT CABINET L4400UA
1EM020848A
FRONT CABINET L4401UB
1EM021393A
BRAND BADGE L T9000UA~SYLVANIA~ 0EM409016
A3
CONTROL PLATE L4300UA
A4
REAR CABINET L4400UA
1EM020849
A5
DECORATION PLATE L4400UA
1EM121052
X2#
X2#
BAG POLYETHYLENE 235X365XT0.03
0EM408420A
OWNERS MANUAL L4400UA
1EMN21430A
OWNERS MANUAL L4401UB
1EMN21763
X3
REMOTE CONTROL NF000UD 170/

ECNLC401/NF000UD
NF000UD
X4
DRY BATTERY(SUNRISE) R6SSE/2S
XB0M451MS002
1EM321266
A6#
RATING LABEL L4400UA
----------
A6#
RATING LABEL L4401UB
----------
FUNCTION KNOB L4300UA
1EM120992
A18
STAND COVER L4300UA
1EM020914
A18
STAND COVER L4301UB
1EM221344
A24
STAND BASE PLATE L4300UA
1EM121113
A25
STAND RUBBER FOOT L4300UA
1EM422534
A26
STAND HINGE L4300UA
1EM220784
B1
PANEL HOLDER L4400UA
1EM020850
B2
PCB HOLDER L4300UA
1EM120995
B3
SHIELD BOX L4300UA
1EM120996
B4
CHASSIS BRACKET L4300UA
1EM120993
B5
JACK HOLDER(A) L4300UA
1EM220681
B6
JACK HOLDER(D) L4300UA
1EM220682
B12
NUT 3/8-32UNEF
0EM401451A
B13
GRAND TAPE L4300UA
1EM423095
B15
GRAND TAPE L4400UA
1EM423347
B16
CLOTH(10X190XT0.3) L0200UA
1EM420019
B17
CLOTH(12X125XT 0.5) L0101JB
0EM408489
B18
CLOTH(10X180XT0.5) L0336JG
0EM408827
B19
CLOTH(20X65XT0.5) L0100JA
0EM407914
CLN253
WIRE ASSEMBLY 104 WX1L4400-104
WX1L4400-104
CLN803
WIRE ASSEMBLY 101 2PIN 210MM

AWG24 RE
WX1L4300-101
CLN804
WIRE ASSEMBLY 101 2PIN 210MM

AWG24 RE
WX1L4300-101
L1
SCREW P-TIGHT 4X14 BIND HEAD
GBJP4140
L2
SCREW P-TIGHT M4X14 PAN

HEAD+BLK
GPHP4140
L3
SCREW S-TIGHT M3X6 BIND HEAD+
GBJS3060
L5
SCREW P-TIGHT 3X10 BIND HEAD+
GBJP3100
L6
DOUBLE SEMS SCREW M4X10 + BLK
FPH34100
L8
DOUBLE SEMS SCREW M4X6 M4X6
FPJ34060
L9
SCREW P-TIGHT 3X10 BIND HEAD+
GBHP3100
L10
SCREW P-TIGHT M3X12 DISH HEAD+
GDJP3120
L11
SCREW TAP TIGHT M3X10 BIND

HEAD+BLK NI
GBHS3100
L12
SCREW P-TIGHT M3X8 BIND HEAD+
GBJP3080
20060316
SP802
ACCESSORIES
A2
A7
DSD0813XQ002
S2
Comparison Chart of Models and Marks

Model
Part No.
SPEAKER S0516F06
PACKING
NOTE: Parts that are not assigned part numbers

(---------) are not available.
6632LCT
Description
SP801
12-1
L4400CA
ELECTRICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a
# have special characteristics important to safety.
Before replacing any of these components, read
carefully the product safety notice in this service
manual. Don't degrade the safety of the product
through improper servicing.
Ref. No.
C451
2. Tolerance of Capacitors and Resistors are noted

with the following symbols.
Part No.
CHD1JZ30F104
C452
ELECTROLYTIC CAP. 100F/10V M
CA1A101SP085
C453
CHIP CERAMIC CAP.(1608) F Z 0.1F/50V
CHD1JZ30F104
C454
CA1C100SP085
C501
CERAMIC CAP. B K 1000pF/500V
CCD2JKP0B102
C503
ALUMINUM ELECTROLYTIC CAP 4700F/35V CE1GMZNTM472

M
NOTES:
1. Parts that are not assigned part numbers (---------)
are not available.
Description
C504
C505
ALUMINUM ELECTROLYTIC CAP 1000F/25V CE1EMZPTM102

M
CA1J100SP085
C506
CERAMIC CAP.(AX) B K 0.01F/50V
CA1J103TU011
C507
CHIP CERAMIC CAP. F Z 0.01F/50V
CHD1JZ30F103
CA1C101SP085
C508
C.....0.25%
D.....0.5%
F.....1%
C509

M
G.....2%
J......5%
K.....10%
C510
CA1C471SP085
C511
ELECTROLYTIC CAP. 0.1F/50V M
CE1JMASDL0R1
M.....20%
N.....30%
Z.....+80/-20%
C531
CERAMIC CAP.(AX) B K 470pF/50V
CCA1JKT0B471
C532
ALUMINUM ELECTROLYTIC CAP 4700F/6.3V CE0KMZNTM472

M
C533
CHD1EZ30F103
C535
CA1J100SP085
C536
ELECTROLYTIC CAP. 1000F/6.3V M
CA0K102SP085
C537
ALUMINUM ELECTROLYTIC CAP 4700F/10V CE1AMZNTM472

M
LCD MODULE ASSEMBLY

*White Balance Adjustment and Flicker Adjustment
are needed when reparing T-CON CBA.
Ref. No.
Description
Part No.
LCD MODULE ASSEMBLY

Consists of the following:
1FSA10108
T-CON CBA
CELL ACF ASSEMBLY
BACKLIGHT ASSEMBLY
1FSA10109
-------------------

Ref. No.
Description
Part No.
1ESA12816
MMA CBA
Ref. No.
Description
Part No.
MMA CBA
1ESA12534
MAIN CBA
FUNCTION CBA
LED CBA
----------------------------
MAIN CBA
Ref. No.
Description
MAIN CBA
Part No.
----------
CAPACITORS
C538
FILM CAP.(P) 0.01F/50V J
CA1J103MS029
C539
CA1J473TU011
C540
ALUMINUM ELECTROLYTIC CAP 1000F/25V CE1EMZPTM102

M
C541
C542

M
CA0K102SP085
C543
C544
CERAMIC CAP.(AX) F Z 0.01F/25V
CA1J100SP085
CDA1EZT0F103
C545
CA1J103TU011
C546
CA1J103TU011
C547
CA0K102SP085
C548
CDA1EZT0F103
C549
CA0K471SP085
C553
CA1E221SP085
C554
CA1A101SP085
C555
CA1J100SP085
C556
CA1J100SP085
C557
CHIP CERAMIC CAP.(1608) B K 0.1F/50V
CHD1JK30B104
C559
CA1A101SP085
C560
CA1J100SP085
C561
CHD1JK30B104
CA1J100SP085
C562
C563
CHD1JK30B104
C564
CHD1JK30B104
C251
CA1A101SP085
C565
CHD1JK30B104
C252
CDA1EZT0F103
C566
CHD1JK30B104
CA0K102SP085
C253
ELECTROLYTIC CAP.(47F/50V) 50MA47HC+T CA1J470SP085
C567
C255
CHD1JZ30F103
C570
CA0K102SP085
C402
CA1J4R7SP085
C572
CCA1JKT0B102
C405
CA1J4R7SP085
C573
CDA1EZT0F103
C408
CA1J4R7SP085
C574
CHD1JZ30F103
C411
CA1J4R7SP085
C575
CHIP CERAMIC CAP.(1608) B K 2700pF/50V
CHD1JK30B272
C415
CA1E4R7SP085
C601#
FILM CAP.(MP) 0.22F/275V K
CT2E224DC011
C418
CA1E4R7SP085
C602#
FILM CAP.(MP) 0.22F/275V K
CT2E224DC011
C421
CA1E4R7SP085
C604
CERAMIC CAP. B K 0.01F/500V
CCD2JKP0B103
C424
CA1E4R7SP085
C605
CCD2JKP0B103
20060316
13-1
L4400EL
Ref. No.
Description
Part No.
C606#
ALUMINUM ELECTROLYTIC CAP 470F/200V CA2D471NC190

M
C609
CERAMIC CAP. BN 1000pF/2KV
CCD3DKA0B102
C610
CA1J333MS029
C615
CA1J683MS029
C633
CA1J333MS029
C634
CERAMIC CAP. BN 680pF/2KV
CCD3DKA0B681
C639
CA1J683MS029
C640
ALUMINUM ELECTROLYTIC CAP 150F/200V CE2DMZNTM151

M
C641
Ref. No.
Description
Part No.
C810
CA1J100SP085
C811
CA1A101SP085
C813
ELECTROLYTIC CAP 1F/50V M
CA1J1R0SP085
C814
ELECTROLYTIC CAP 1F/50V M
CA1J1R0SP085
CONNECTORS
CN111
TWG CONNECTOR 23P TWG-P23P-A1
J3TWA23TG001
CN112
J3TWA23TG001
CN113
J3TWA23TG001
CN114
J3TWA23TG001
CCD2JKP0B103
CN151A
BOARD IN WIRE 106 10PIN 150MM-AWG26
WX1L4300-106
CN253
PH CONNECTOR TOP 20P B20B-PHDSSB(LF)(SN)
J3F5D20JG003
D251
SWITCHING DIODE 1SS133(T-77)
QDTZ001SS133
D501
DIODE SCHOTTKY YG802C10R
QDQZYG802C10
C642
CCD2JKP0B103
C691#
SAFETY CAP. 3300pF/250V
CCG2EMPYV332
C692
SAFETY CAP. 3300pF/250V
CCG2EMPYV332
C701
CHIP CERAMIC CAP.(1608) CH J 100pF/50V
CHD1JJ3CH101
C702
CA1C470SP085
C704
CHD1JZ30F103
C705
CHD1JJ3CH101
C706
CA1C470SP085
C708
CHD1JZ30F103
C709
CHD1JJ3CH101
C710
CA1C470SP085
C711
CHD1JZ30F103
C712
CA1A101SP085
C714
CHD1JJ3CH101
C715
CCA1JKT0B102
C716
CHD1JZ30F103
C718
CHD1JJ3CH101
C719
CA1C470SP085
C720
CHD1JZ30F103
C721
CA1A101SP085
C723
CHD1JJ3CH101
C724
CCA1JKT0B102
C725
CHD1JZ30F103
C727
CA1A101SP085
C728
CA1A101SP085
C729
CHD1JJ3CH330
C730
CA1C470SP085
C732
PCB JUMPER D0.6-P5.0
JW5.0T
C733
CHD1JJ3CH330
C734
CA1C470SP085
C736
JW5.0T
C737
CHD1JZ30F103
C738
CHD1JJ3CH330
C739
CA1C470SP085
C741
CHD1JZ30F103
C742
JW5.0T
C743
CHD1JJ3CH330
C744
CA1C470SP085
C746
JW5.0T
C747
CHD1JJ3CH330
C748
CA1C470SP085
DIODES
D502
SCHOTTKY BARRIER DIODE ERB84-009
QD7Z000ERB84
D503
DIODE FR104-B
NDLZ000FR104
D504
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
D505
ZENER DIODE MTZJT-7712B
QDTB00MTZJ12
D507
QDTZ001SS133
D508
QDTZ001SS133
D509
DIODE 1ZC30(Q)
QDLZ001ZC30Q
D510
QDTB00MTZJ27
D531
DIODE SCHOTTKY 31DQ03L
QDLZ031DQ03L
D532
DIODE SCHOTTKY 31DQ03L
QDLZ031DQ03L
D533
SCHOTTKY BARRIER DIODE ERC81-006
QDQZERC81006
D534
SCHOTTKY BARRIER DIODE ERC81-004
QDPZERC81004
D536
RECTIFIER DIODE FR202-B/P
NDQZ000FR202
D537
DIODE FR104-B
NDLZ000FR104
D538
QDTZ001SS133
D539
ZENER DIODE MTZJT-776.8B
QDTB0MTZJ6R8
D540
DIODE 1ZC43(Q)
QDLZ001ZC43Q
D541
QDTB00MTZJ33
D542
IC SHUNT REGULATOR KIA431-AT/P
NSZBA0TJY036
D543
QDTZ001SS133
D544
QDTZ001SS133
D545
QDTB0MTZJ3R3
D546
QDTZ001SS133
D547
QDTZ001SS133
D549
QDTZ001SS133
D551
QDTZ001SS133
D552
QDTZ001SS133
D553
QDTB00MTZJ15
D554
QDTZ001SS133
D555
QDTZ001SS133
D556
QDTZ001SS133
D557
QDTZ001SS133
D558
QDTZ001SS133
D559
QDTZ001SS133
D561
QDTZ001SS133
D563
RECTIFIER DIODE ERA22-02
QDPZ0ERA2202
D564
QDTZ001SS133
D566
QDTZ001SS133
D582
QDTZ001SS133
D583
QDTZ001SS133
D591
QDTZ001SS133
D592
QDTZ001SS133
QDTB0MTZJ4R7
C750
JW5.0T
C751
CHD1JJ3CH330
C752
CA1C470SP085
C754
JW5.0T
C801
ALUMINUM ELECTROLYTIC CAP 1000F/35V CE1GMZPTM102

M
C802
CA1G221SP085
D593
C803
CA1G221SP085
D594
QDTB0MTZJ3R9
C804
CA1J104MS029
D601#
DIODE 1N5406
NDLZ001N5406
C805
CA1J104MS029
D602#
DIODE 1N5406
NDLZ001N5406
C807
CA1E101SP085
D603#
DIODE 1N5406
NDLZ001N5406
C809
CA1J3R3SP085
D604#
DIODE 1N5406
NDLZ001N5406
20060316
13-2
L4400EL
Ref. No.
Description
D607#
D608
D609
Part No.
Ref. No.
Description
Part No.
QDTB00MTZJ27
Q537
TRANSISTOR KTC3199-GR-AT/P
NQS4KTC3199P
QDTB0MTZJ7R5
Q601#
FET MOS 2SK3797(Q)
QFQZ02SK3797
QDTZ001SS133
Q602#
TRANSISTOR 2SC2120-O(TE2 F T)
QQS02SC2120F
D610
QDTZ001SS133
Q603
NQS4KTC3199P
D611#
QDTZ001SS133
Q631#
MOS FET 2SK3563
QFWZ02SK3563
D612#
QDTB00MTZJ18
Q632#
QQS02SC2120F
D632#
QDTB00MTZJ27
Q701
NQS4KTC3199P
D633
QDTB0MTZJ5R6
Q702
NQS4KTC3199P
D634
QDTZ001SS133
Q703
NQS4KTC3199P
D635
QDTZ001SS133
Q704
NQS4KTC3199P
D636#
QDTZ001SS133
Q705
NQS4KTC3199P
D637#
QDTB00MTZJ18
Q706
NQS4KTC3199P
D638#
DIODE 1N5397-B
NDLZ001N5397
Q707
NQS4KTC3199P
D639#
DIODE 1N5397-B
NDLZ001N5397
Q708
NQS4KTC3199P
D640#
DIODE 1N5397-B
NDLZ001N5397
Q709
NQS4KTC3199P
D641#
DIODE 1N5397-B
NDLZ001N5397
Q710
NQS4KTC3199P
D707
QDTZ001SS133
Q711
NQS4KTC3199P
D708
QDTZ001SS133
Q712
NQS4KTC3199P
D709
QDTZ001SS133
Q801
QQS02SC2120F
D710
QDTZ001SS133
Q802
NQS4KTC3199P
D801
JW5.0T
Q803
TRANSISTOR 2SA1931(Q)
QQZZ2SA1931Q
D802
JW5.0T
Q804
NQS4KTC3199P
D803
QDTB00MTZJ15
D814
QDTZ001SS133
R251
CARBON RES. 1/4W J 22
RCX4JATZ0220
D816
QDTZ001SS133
R254
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
D881
QDTZ001SS133
R257
CHIP RES. 1/10W J 4.7k
RRXAJR5Z0472
R258
CHIP RES. 1/10W J 100
RRXAJR5Z0101
RESISTORS
ICS
IC451
IC ANALOG MULTIPLEXER CD4051BNSR
NSZBA0TTY157
R259
RRXAJR5Z0471
IC452
IC ANALOG MULTIPLEXER CD4051BNSR
NSZBA0TTY157
R260
RRXAJR5Z0472
IC531
VOLTAGE REGULATOR PQ070XF01SZH
QSZBA0SSH054
R261
RRXAJR5Z0472
IC532
REGULATOR IC(3.5V) PQ035ZN1HZPH
QSZBA0TSH078
R262
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
IC533
REGULATOR PQ018EF01SZH
QSZBA0SSH075
R401
CHIP RES. 1/10W J 47k
RRXAJR5Z0473
IC534
IC VOLTAGE REGULATOR 5V KIA7805API/P
NSZBA0SJY041
R402
CARBON RES. 1/4W J 5.6k
RCX4JATZ0562
IC535
IC LD1117V
NSZBA0SSS046
R403
RRXAJR5Z0562
IC536#
REGULATOR PQ1CG2032FZH
QSZBA0SSH071
R404
RRXAJR5Z0473
IC537
REGULATOR(PB FREE) PQ033EF01SZH
QSZBA0SSH060
R405
RCX4JATZ0562
IC601
PHOTOCOUPLER LTV-817C-F
NPEC0LTV817F
R406
RRXAJR5Z0562
IC602
NPEC0LTV817F
R407
RRXAJR5Z0473
IC631
NPEC0LTV817F
R408
RRXAJR5Z0562
IC801
AUDIO POWER IC AN17805A
QSZBA0SMS007
R409
RRXAJR5Z0562
R410
RRXAJR5Z0473
COILS
L501
JW5.0T
R411
RRXAJR5Z0562
L532
POWER INDUCTOR RCR1616-470M
LLC470MSF009
R412
RRXAJR5Z0562
L533
CHOKE COIL 47H
LLBD00PKV022
R413
RRXAJR5Z0473
L534
INDUCTOR 15H-K-5FT
LLARKBSTU150
R414
RRXAJR5Z0562
L601#
FILTER LLBG00ZY2015
LLBG00ZY2015
R415
RRXAJR5Z0562
L602#
FILTER LLBG00ZY2015
LLBG00ZY2015
R416
RRXAJR5Z0473
R417
RRXAJR5Z0562
TRANSISTORS
Q251
NQS4KTC3199P
R418
RRXAJR5Z0562
Q252
NQS4KTC3199P
R419
RRXAJR5Z0473
RRXAJR5Z0562
Q451
NQS4KTC3199P
R420
Q452
NQS4KTC3199P
R421
RRXAJR5Z0562
Q453
NQS4KTC3199P
R422
RRXAJR5Z0473
Q501
TRANSISTOR(PB FREE) KTC2026-Y/P
NQEYKTC2026P
R423
RRXAJR5Z0562
RRXAJR5Z0562
RRXAJR5Z0104
Q502
NQS4KTC3199P
R424
Q503
NQS4KTC3199P
R453
Q504
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
R454
RRXAJR5Z0104
Q531
TRANSISTOR KTA1267-GR-AT/P
NQS1KTA1267P
R455
RRXAJR5Z0104
Q533
NQS4KTC3199P
R456
RRXAJR5Z0104
Q534
NQS4KTC3199P
R457
RRXAJR5Z0104
Q535
NQS4KTC3199P
R458
RRXAJR5Z0104
Q536
NQS1KTA1267P
R459
RRXAJR5Z0101
20060316
13-3
L4400EL
Ref. No.
R460
Description
Part No.
Ref. No.
Description
Part No.
RRXAJR5Z0103
R546
RRXAJR5Z0102
R461
RRXAJR5Z0104
R547
METAL OXIDE FILM RES. 2W J 0.1
RN02R10KE010
R462
RRXAJR5Z0104
R548
RRXAJR5Z0101
R463
RRXAJR5Z0104
R551
RRXAJR5Z0822
R464
RRXAJR5Z0104
R555
RCX4JATZ0561
R465
CARBON RES. 1/4W J 100k
RCX4JATZ0104
R556
RRXAJR5Z0223
R466
RRXAJR5Z0104
R557
RCX4JATZ0821
R473
RRXAJR5Z0104
R558
CHIP RES.(1608) 1/10W F 2.2k
RRXAFR5Z2201
R474
RRXAJR5Z0104
R561
CHIP RES. 1/10W F 680
RRXAFR5H6800
R475
RRXAJR5Z0104
R562
RRXAFR5H2200
R476
RCX4JATZ0104
R563
RRXAJR5Z0223
R477
RRXAJR5Z0104
R565
RCX4JATZ0103
R478
RRXAJR5Z0104
R566
RRXAJR5Z0473
R479
RRXAJR5Z0101
R567
RCX4JATZ0152
R480
RRXAJR5Z0103
R568
RCX4JATZ0152
R481
RRXAJR5Z0104
R569
JW5.0T
R482
RRXAJR5Z0104
R570
RRXAJR5Z0472
R483
RRXAJR5Z0104
R571
RRXAJR5Z0103
R484
RRXAJR5Z0104
R573
RCX4JATZ0103
R485
RRXAJR5Z0104
R574
JW5.0T
R486
RRXAJR5Z0104
R575
RCX4JATZ0221
R488
JW5.0T
R576
RCX4JATZ0473
R491
RCX4JATZ0103
R577
RCX4JATZ0102
R492
RCX4JATZ0103
R583
RRXAJR5Z0223
R493
RCX4JATZ0103
R584
RRXAJR5Z0332
R494
RRXAJR5Z0223
R585
RCX4JATZ0103
R495
RRXAJR5Z0223
R586
RRXAJR5Z0332
R496
RRXAJR5Z0223
R590
RCX4JATZ0621
R500
RN011R2ZU001
R591
RCX4JATZ0102
R501
CHIP RES. 1/10W F 8.2k
RRXAFR5H8201
R601#
CARBON RES. 1/2W J 3.3M
RCX2JZQZ0335
R502
RRXAFR5H8201
R602#
CEMENT RESISTOR 5W J 0.82
RW05R82PAK10
R503
RRXAJR5Z0272
R603#
RCX4JATZ0394
R506
JW5.0T
R604
RCX4JATZ0394
R507
RCX4JATZ0102
R605
JW5.0T
R508
CHIP RES. 1/10W F 22k
RRXAFR5H2202
R606
RCX4JATZ0394
R509
RRXAFR5H1502
R607#
RCX4JATZ0564
R510
RCX4JATZ0821
R608
RCX4JATZ0564
R511
RRXAJR5Z0223
R609
RCX4JATZ0564
R512
CHIP RES.(1608) 1/10W F 2.2k
RRXAFR5Z2201
R611
JW5.0T
R513
RRXAJR5Z0562
R612
RCX4JATZ0334
R514
RRXAJR5Z0222
R613
RCX4JATZ0271
R515
RCX4JATZ0152
R614
RCX4JATZ0221
R516
RCX4JATZ0101
R615
JW5.0T
R517
RCX4JATZ0272
R617
RCX4JATZ0152
R518
RRXAJR5Z0103
R618
RCX4JATZ0181
R519
RRXAJR5Z0562
R620#
RN02R27ZU001
R520
RRXAJR5Z0332
R621
RCX4JATZ0151
R523
METAL RESISTOR 2W J 820
RN02821ZU001
R622
RCX4JATZ0222
R524
METAL RESISTOR 2W J 820
RN02821ZU001
R631#
RCX4JATZ0394
R530
RRXAFR5Z7501
R632
RCX4JATZ0394
R531
CARBON RES. 1/4W G 5.1k
RCX4GATZ0512
R633
RCX4JATZ0394
R532
RCX4JATZ0103
R634
RCX4JATZ0394
R533
RRXAFR5Z6801
R636
RCX4JATZ0271
R534
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R637
RCX4JATZ0221
R535
RRXAJR5Z0472
R639
RCX4JATZ0821
R536
RRXAFR5H1101
R641
RCX4JATZ0560
R537
RRXAFR5Z1001
R642
RCX4JATZ0222
R538
RCX4JATZ0103
R643
RCX4JATZ0151
R540
RRXAJR5Z0103
R644#
RN02R47ZU001
R541
CARBON RES. 1/4W G 1.6k
RCX4GATZ0162
R646
CEMENT RESISTOR 3W K 1.2
RW031R2PAK10
R543
METAL OXIDE FILM RES. 1W J 1k
RN01102ZU001
R701
RCX4JATZ0750
R544
RCX4JATZ0102
R702
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R545
RCX4JATZ0103
R704
RRXAJR5Z0333
20060316
13-4
L4400EL
Ref. No.
Description
Ref. No.
Part No.
Description
Part No.
R705
RRXAJR5Z0393
R783
RRXAJR5Z0333
R706
RRXAJR5Z0391
R784
RRXAJR5Z0393
R707
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R785
RRXAJR5Z0391
R708
RRXAJR5Z0750
R786
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R709
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R787
RRXAFR5Z75R0
R711
RRXAJR5Z0333
R788
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R712
RRXAJR5Z0393
R791
RRXAJR5Z0333
R713
RRXAJR5Z0391
R792
RRXAJR5Z0393
R714
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R793
RRXAJR5Z0391
R715
RRXAJR5Z0750
R794
JW5.0T
R716
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R801
RN02R33ZU001
R718
RRXAJR5Z0333
R803
RCX4JATZ0101
R719
RRXAJR5Z0393
R804
RCX4JATZ0103
R720
RRXAJR5Z0391
R807
RCX4JATZ0103
R721
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R808
RCX4JATZ0101
R722
RCX4JATZ0220
R809
RCX4JATZ0272
R723
RRXAJR5Z0750
R810
JW5.0T
R724
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R811
RCX4JATZ0101
R726
RRXAJR5Z0333
R812
RCX4JATZ0101
R727
RRXAJR5Z0393
R813
JW5.0T
R728
RRXAJR5Z0391
R815
RCX4JATZ0103
R729
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R816
RCX4JATZ0472
R730
RRXAJR5Z0750
R817
METAL OXIDE FILM RES. 2W J 560
RN02561KE010
R731
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R823
JW5.0T
R733
RRXAJR5Z0333
R824
RCX4JATZ0102
R734
RRXAJR5Z0393
R825
RCX4JATZ0391
R735
RRXAJR5Z0391
R826
RCX4JATZ0222
R736
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R827
RCX4JATZ0222
R737
RCX4JATZ0220
R828
RCX4JATZ0391
R738
RCX4JATZ0750
R829
RCX4JATZ0472
R739
JW5.0T
R830
RCX4JATZ0102
R741
RRXAJR5Z0333
R831
RCX4JATZ0103
R742
RRXAJR5Z0393
R881
RCX4JATZ0153
R743
RRXAJR5Z0391
R882
RCX4JATZ0222
R744
JW5.0T
R927
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
R745
RCX4JATZ0220
R931
RRXAJR5Z0103
R746
RCX4JATZ0220
R747
RRXAFR5Z75R0
AC601#
AC CORD LP-11W&PT218P-K90A&S
R748
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
B9
HEAT SINK EAB ASSEMBLY L4300UA
1EM422612
R751
RRXAJR5Z0333
B10
HEAT SINK PKH ASSEMBLY L3201UB
1EM420648
R752
RRXAJR5Z0393
B11
HEAT SINK PLQ ASSEMBLY L4300UA
1EM422615
R753
RRXAJR5Z0391
BC301
JW5.0T
R754
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
BC302
JW5.0T
R755
RRXAFR5Z75R0
BC304
JW5.0T
R756
JW5.0T
BC501
BEAD INDUCTORS FBR07HA121TB-00
LLBF00ZTU021
R759
RRXAJR5Z0333
BC502
LLBF00ZTU021
R760
RRXAJR5Z0393
BC503
LLBF00ZTU021
R761
RRXAJR5Z0391
BC531
LLBF00ZTU021
R762
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
BC532
LLBF00ZTU021
R763
RRXAFR5Z75R0
BC601
LLBF00ZTU021
R764
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
BC602
LLBF00ZTU021
R767
RRXAJR5Z0333
BC631
LLBF00ZTU021
R768
RRXAJR5Z0393
BC632
LLBF00ZTU021
R769
RRXAJR5Z0391
F601#
FUSE STC4A125V U/CT
LLBF00ZTU021
R770
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
FC101
CLAMP FILTER ZCAT1325-0530A
XL03025TE001
R771
RRXAFR5Z75R0
FH601
FUSE HOLDER MSF-015
XH01Z00LY001
R772
JW5.0T
FH602
FUSE HOLDER MSF-015
XH01Z00LY001
R775
RRXAJR5Z0333
GP691
GAP. FNR-G3.10D
FAZ000LD6005
R776
RRXAJR5Z0393
JK701
6PIN JACK MSP-226V27-01 NI FE
JYRL060LY032
R777
RRXAJR5Z0391
JK702
Y/C JACK(SW) YKF51-5563N
JYEL080JC002
R778
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
JK703
JYRL050LY033
R779
RRXAFR5Z75R0
JK704
JYRL050LY033
R780
CHIP RES.(1608) 1/10W 0
RRXAJR5Z0000
20060316
MISCELLANEOUS
13-5
WAC0172LW020
L4400EL
Ref. No.
Description
Part No.
Ref. No.
Description
JW5.0T
Part No.
JS803
L4
SCREW B-TIGHT D3X8 BIND HEAD+
GBJB3080
D151
LED 333GT/E
NPHZ00333GTE
SA601#
SURGE ABSORBER 470V+-10PER
NVQZ10D471KB
D152
LED L-53HT
NP4Z000L53HT
T601#
SW TRANS 6706
LTT4PC0KT001
T631#
SW TRANS 5809
LTT2PC0KT004
R151
RCX4JATZ0221
R152
RCX4JATZ0221
R153
RCX4JATZ0102
R154
RRXAJR5Z0332
R155
RRXAJR5Z0101
DIODES
RESISTORS
FUNCTION CBA
Ref. No.
Description
FUNCTION CBA
Part No.
----------
MISCELLANEOUS
CAPACITORS
C101
CHD1JZ30F104
C102
CHD1JZ30F104
C103
CHD1JZ30F104
C104
CHD1JZ30F104
PH CONNECTOR SIDE 5P S5B-PH-KS(LF)(SN)
JW5.0T
RCV151
PHOTO LINK MODULE KSM-712TH2E
USESJRSKK044
INVERTER CBA
Ref. No.
CONNECTOR
CN101
BC151
J3PHC05JG030
R102

JW5.0T
RRXAJR5Z0103
R103
RRXAJR5Z0103
R104
JW5.0T
R105
RRXAJR5Z0242
R106
RCX4JATZ0432
RRXAJR5Z0822
R108
RRXAJR5Z0243
R110
RRXAJR5Z0822
RRXAJR5Z0242
RRXAJR5Z0432
R113
RRXAJR5Z0822
R114
RRXAJR5Z0243
R107
R111
R112
Part No.
1ESA12537
CAPACITORS
RESISTORS
R101
Description
INVERTER CBA
C1000
CHIP CERAMIC CAP. B K 1000pF/50V
C1001
CHD1JKB0B102
CHD1AZ30F225
C1002
CHD1JKB0B102
C1003
CHD1JKB0B102
C1004
CHIP CERAMIC CAP. B K 0.01F/50V
CHD1JKB0B103
C1005
CHD1JJ3CH102
C1006
CHD1JKB0B473
C1007
CHIP CERAMIC CAP. CH J 330pF/50V
CHD1JJBCH331
C1008
CHD1AZ30F225
C1009
CHIP CERAMIC CAP. F Z 1F/10V
CHD1AZB0F105
C1010
CHIP CERAMIC CAP. F Z 1F/10V
CHD1AZB0F105
C1011
CHD1AK30B474
C1012
CHD1AK30B474
C1015
ALUMINUM ELECTROLYTIC CAP 470F/35V

M
CE1GMZNTM471
R115
RRXAJR5Z0432
R116
JW5.0T
C1016
CHD1JK30B104
R117
RRXAJR5Z0242
CHD1JK30B104
R118
C1017
RRXAJR5Z0103
C1018
CHD1JK30B104
C1019
CHD1JK30B104
SWITCHES
SW101
TACT SWITCH SKQSAB
SST0101AL038
C1020
CHD1JKB0B103
SW102
TACT SWITCH SKQSAB
SST0101AL038
C1030
CE1CMASDL331
SW103
TACT SWITCH SKQSAB
SST0101AL038
C1031
CHD1JK30B104
SW104
TACT SWITCH SKQSAB
SST0101AL038
C1032
CE1GMASDL470
SW105
TACT SWITCH SKQSAB
SST0101AL038
C1040
CHD1JKB0B102
SW114
TACT SWITCH SKQSAB
SST0101AL038
C1043
CE1JMASDL2R2
SW115
TACT SWITCH SKQSAB
SST0101AL038
LED CBA
Ref. No.
Description
LED CBA
Part No.
----------
CAPACITORS
C151
CHD1JZ30F104
C152
CHD1JZ30F104
C153
CHD1JZ30F104
C154
CHD1JZ30F103
C155
ELECTROLYTIC CAP. 47F/10V M H7
CE1AMASSM470
CN151
PH CONNECTOR SIDE10PIN S10B-PH-K-S

(LF)(SN)
J3PHC10JG030
CN803
J3PHC02JG030
J3PHC02JG030
CONNECTORS
CN804
20060316
13-6
C1044
CHIP CERAMIC CAP.(1608) B K 1F/10V
CHD1AK30B105
C1045
CE1JMASDL2R2
C1046
CHIP CERAMIC CAP.(1608) B K 1F/10V
CHD1AK30B105
C1061
CERAMIC CAP. SL D 10pF/3KV
CCD3FDASL100
C1062
CHD1JK30B122
C1063
CHD1JKB0B222
C1064
CCD3FDASL100
C1065
CHD1JK30B122
C1066
CHD1JKB0B222
C1067
CHD1JKB0B103
C1100
CE1GMASDL101
C1101
CHD1JK30B104
C1102
CE1GMASDL101
C1103
CHD1JK30B104
C1111
CCD3FDASL100
C1112
CHD1JK30B122
C1113
CHD1JKB0B222
C1114
CCD3FDASL100
C1115
CHD1JK30B122
L4400EL
Ref. No.
Description
C1116
C1117
C1161
Part No.
Ref. No.
Description
Part No.
CHD1JKB0B222
D1060
QDTZ001SS133
CHD1JKB0B103
D1061
QDTZ001SS133
CCD3FDASL100
D1062
QDTZ001SS133
C1162
CHD1JK30B122
D1063
SCHOTTKY BARRIER DIODE ERA81-004Q
QDLZRA81004Q
C1163
CHD1JKB0B222
D1064
QDTZ001SS133
C1164
CCD3FDASL100
D1065
QDTZ001SS133
C1165
CHD1JK30B122
D1066
QDTZ001SS133
C1166
CHD1JKB0B222
D1067
QDTZ001SS133
C1167
CHD1JKB0B103
D1068
QDTZ001SS133
C1211
CCD3FDASL100
D1110
QDTZ001SS133
C1212
CHD1JK30B122
D1111
QDTZ001SS133
C1213
CHD1JKB0B222
D1112
QDTZ001SS133
C1214
CCD3FDASL100
D1113
QDTZ001SS133
C1215
CHD1JK30B122
D1114
QDTZ001SS133
C1216
CHD1JKB0B222
D1115
QDTZ001SS133
C1217
CHD1JKB0B103
D1116
QDTZ001SS133
C1250
CE1GMASDL101
D1117
QDLZRA81004Q
C1251
CHD1JK30B104
D1118
QDTZ001SS133
C1252
CE1GMASDL101
D1160
QDTZ001SS133
C1253
CHD1JK30B104
D1161
QDTZ001SS133
C1261
CCD3FDASL100
D1162
QDTZ001SS133
C1262
CHD1JK30B122
D1163
QDLZRA81004Q
C1263
CHD1JKB0B222
D1164
QDTZ001SS133
C1264
CCD3FDASL100
D1165
QDTZ001SS133
C1265
CHD1JK30B122
D1166
QDTZ001SS133
C1266
CHD1JKB0B222
D1167
QDTZ001SS133
C1267
CHD1JKB0B103
D1168
QDTZ001SS133
C1311
CCD3FDASL100
D1210
QDTZ001SS133
C1312
CHD1JK30B122
D1211
QDTZ001SS133
C1313
CHD1JKB0B222
D1212
QDTZ001SS133
C1314
CCD3FDASL100
D1213
QDTZ001SS133
C1315
CHD1JK30B122
D1214
QDTZ001SS133
C1316
CHD1JKB0B222
D1215
QDTZ001SS133
C1317
CHD1JKB0B103
D1216
QDTZ001SS133
C1500
CHD1EK30B224
D1217
QDLZRA81004Q
C1501
CHD1EK30B224
D1218
QDTZ001SS133
C1502
CHD1EK30B224
D1260
QDTZ001SS133
C1550
CHD1EK30B224
D1261
QDTZ001SS133
C1552
CHD1EK30B224
D1262
QDTZ001SS133
D1263
QDLZRA81004Q
D1264
QDTZ001SS133
D1265
QDTZ001SS133
CONNECTORS
CN1000
PH CONNECTOR TOP 20P B20B-PHDSSB(LF)(SN)
J3F5D20JG003
CN1050
CONNECTOR/JACK 1747386-1
JB17J02AP002
D1266
QDTZ001SS133
CN1100
JB17J02AP002
D1267
QDTZ001SS133
CN1150
JB17J02AP002
D1268
QDTZ001SS133
CN1200
JB17J02AP002
D1310
QDTZ001SS133
CN1250
JB17J02AP002
D1311
QDTZ001SS133
CN1300
JB17J02AP002
D1312
QDTZ001SS133
D1313
QDTZ001SS133
DIODES
D1000
QDTZ001SS133
D1314
QDTZ001SS133
D1001
QDTZ001SS133
D1315
QDTZ001SS133
D1002
QDTB0MTZJ6R2
D1316
QDTZ001SS133
D1003
QDTB0MTZJ6R2
D1317
QDLZRA81004Q
D1004
QDTB0MTZJ6R2
D1318
QDTZ001SS133
D1005
QDTB0MTZJ6R2
D1500
QDTZ001SS133
D1020
QDTB0MTZJ5R1
D1501
QDTZ001SS133
D1021
QDTZ001SS133
D1502
QDTZ001SS133
D1030
QDTB0MTZJ5R6
D1503
QDTZ001SS133
D1042
QDTB00MTZJ24
D1550
QDTZ001SS133
D1043
QDTZ001SS133
D1551
QDTZ001SS133
D1045
QDTB00MTZJ24
D1552
QDTZ001SS133
D1046
QDTZ001SS133
D1553
QDTZ001SS133
D1049
QDTZ001SS133
20060316
13-7
L4400EL
Ref. No.
Description
Part No.
Ref. No.
R1105
ICS
Description
Part No.
JW5.0T
IC1000
IC PWM CONTROLLER OZ9938GN
NSZBA0TTMC01
R1110
RRXAJR5Z0104
IC1001
IC MOSFET DRIVER OZ9982GN
NSZBA0TTMC02
R1111
RRXAJR5Z0203
IC1500
IC BA10324AF-E2
QSZBA0TRM032
R1112
RRXAFB5H4700
IC1550
IC BA10324AF-E2
QSZBA0TRM032
R1113
RCX4JATZ0103
R1114
RRXAJR5Z0104
TRANSISTORS
Q1000
TRANSISTOR KTC3205(Y)
NQSY0KTC3205
R1115
RRXAJR5Z0203
Q1001
NQS4KTC3199P
R1116
RRXAFB5H4700
Q1002
NQS4KTC3199P
R1117
RCX4JATZ0103
CHIP RES. 1/10W J 1M
RRXAJR5Z0105
Q1003
NPN TRANSISTOR KRC103M-AT/P
NQSZKRC103MP
R1120
Q1020
NQS1KTA1267P
R1121
RRXAJR5Z0102
Q1100
MOS FET 2SK2614
QF1Z2SK2614Q
R1160
RRXAJR5Z0104
Q1101
MOS FET 2SK2614
QF1Z2SK2614Q
R1161
RRXAJR5Z0203
RRXAFB5H4700
Q1102
MOS FET 2SK2614
QF1Z2SK2614Q
R1162
Q1103
MOS FET 2SK2614
QF1Z2SK2614Q
R1163
RCX4JATZ0103
Q1250
MOS FET 2SK2614
QF1Z2SK2614Q
R1164
RRXAJR5Z0104
Q1251
MOS FET 2SK2614
QF1Z2SK2614Q
R1165
RRXAJR5Z0203
RRXAFB5H4700
Q1252
MOS FET 2SK2614
QF1Z2SK2614Q
R1166
Q1253
MOS FET 2SK2614
QF1Z2SK2614Q
R1167
RCX4JATZ0103
R1170
RRXAJR5Z0105
RRXAJR5Z0203
R1171
RRXAJR5Z0102
RRXAJR5Z0104
RESISTORS
R1000
R1001
RRXAJR5Z0103
R1210
R1002
RRXAJR5Z0512
R1211
RRXAJR5Z0203
R1003
RRXAJR5Z0105
R1212
RRXAFB5H4700
R1004
RRXAJR5Z0103
R1213
RCX4JATZ0103
RRXAJR5Z0104
R1005
CHIP RES. 1/10W F 160 k
RRXAFR5H1603
R1214
R1006
RCX4JATZ0103
R1215
RRXAJR5Z0203
R1007
RRXAJR5Z0303
R1216
RRXAFB5H4700
R1008
RRXAJR5Z0303
R1217
RCX4JATZ0103
RRXAFR5H1004
R1220
RRXAJR5Z0105
RRXAJR5Z0102
R1009
CHIP RES. 1/10W F 1M
R1010
RRXAFR5H1303
R1221
R1011
CHIP RES. 1/10W F 110 k
RRXAFR5H1103
R1250
RRXAJR5Z0330
R1020
RRXAJR5Z0105
R1251
RRXAJR5Z0330
RCX4JATZ0471
R1252
RRXAJR5Z0330
RRXAJR5Z0330
R1030
R1031
RRXAJR5Z0472
R1253
R1040
RRXAJR5Z0472
R1254
JW5.0T
R1041
RRXAJR5Z0103
R1255
JW5.0T
RRXAJR5Z0473
R1260
RCX4JATZ0104
RRXAJR5Z0203
RRXAFB5H4700
R1045
R1046
RCX4JATZ0682
R1261
R1047
RRXAJR5Z0105
R1262
R1048
RRXAJR5Z0102
R1263
RCX4JATZ0103
RRXAJR5Z0104
R1050
RRXAJR5Z0473
R1264
R1051
RCX4JATZ0682
R1265
RRXAJR5Z0203
R1052
RRXAJR5Z0105
R1266
RRXAFB5H4700
R1053
RRXAJR5Z0102
R1267
RCX4JATZ0103
RCX4JATZ0222
R1270
RRXAJR5Z0105
RRXAJR5Z0102
R1055
R1056
RRXAJR5Z0332
R1271
R1060
RRXAJR5Z0104
R1310
RRXAJR5Z0104
R1061
RRXAJR5Z0203
R1311
RRXAJR5Z0203
RRXAFB5H4700
R1312
RRXAFB5H4700
RCX4JATZ0103
R1062
R1063
RCX4JATZ0103
R1313
R1064
RRXAJR5Z0104
R1314
RRXAJR5Z0104
R1065
RRXAJR5Z0203
R1315
RRXAJR5Z0203
RRXAFB5H4700
R1316
RRXAFB5H4700
RCX4JATZ0103
R1066
R1067
RCX4JATZ0103
R1317
R1070
RRXAJR5Z0105
R1320
RRXAJR5Z0105
R1071
RRXAJR5Z0102
R1321
RRXAJR5Z0102
RRXAZR5Z0000
R1500
RRXAFR5H9101
RRXAFR5H1001
R1100
CHIP RES.(1608) 1/10W 0
R1101
CHIP RES.(1608) 1/10W 0
RRXAZR5Z0000
R1501
R1102
CHIP RES.(1608) 1/10W 0
RRXAZR5Z0000
R1502
RRXAFR5H9101
R1103
CHIP RES.(1608) 1/10W 0
RRXAZR5Z0000
R1503
RRXAFR5H1001
JW5.0T
R1504
RCX4JATZ0103
R1505
RRXAJR5Z0103
R1104
20060316
13-8
L4400EL
Ref. No.
Description
Part No.
R1506
RRXAJR5Z0103
R1507
RRXAJR5Z0103
R1508
RRXAJR5Z0103
R1509
RRXAJR5Z0103
R1510
RRXAJR5Z0103
R1511
RRXAJR5Z0103
R1550
RRXAFR5H9101
R1551
RRXAFR5H1001
R1554
RRXAJR5Z0103
R1555
RRXAJR5Z0103
R1556
RRXAJR5Z0103
R1557
RRXAJR5Z0103
R1558
RRXAJR5Z0103
R1559
RRXAJR5Z0103
R1560
RRXAJR5Z0103
R1561
RRXAJR5Z0103
MISCELLANEOUS
B14
SHIELD BOX BOTTOM L4400UA
1EM423172
BC1050
JW10.0T
BC1100
JW10.0T
BC1150
JW10.0T
BC1200
JW10.0T
BC1250
JW10.0T
BC1300
JW10.0T
JS1000
JW5.0T
T1050
INVERTER TRANS ETJV27ZJ23AC
LTZ2PC0MS001
T1100
LTZ2PC0MS001
T1150
LTZ2PC0MS001
T1200
LTZ2PC0MS001
T1250
LTZ2PC0MS001
T1300
LTZ2PC0MS001
20060316
13-9
L4400EL
6632LCT/6632LG
L4400UA/01UB
2006-04-12

Service Manual: 6632LCT/6632LG

Uploaded by

Copyright:

Available Formats

Service Manual: 6632LCT/6632LG

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: 6632LCT/6632LG

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

32 COLOR LCD TELEVISION

IMPORTANT SAFETY NOTICE

The LCD panel is manufactured to provide many years of useful life.

2. Color Killer Sens.

3. AFT Pull In Range (10 mV input)

< LCD PANEL >

16.7 mil. (8 bit)

< VIDEO >

< AUDIO >

10% THD: Lch/Rch

IMPORTANT SAFETY PRECAUTIONS

Safety Precautions for LCD TV

d. Leakage Current Hot Check - With the

1. Before returning an instrument to the

b. Be sure that there are no cabinet openings

TEST ALL EXPOSED

ALSO TEST WITH

c. Antenna Cold Check - With the instrument AC

ANY MEASUREMENTS NOT WITHIN THE

7. Product Safety Notice - Some electrical and

3. Design Alteration Warning - Do not alter or add

Precautions during Servicing

L. When connecting or disconnecting the internal

B. In addition to safety, other parts and assemblies

M. When installing parts or assembling the cabinet

C. Use specified internal wiring. Note especially:

Also check areas surrounding repaired locations.

J. Use care that foreign objects (screws, solder

Safety Check after Servicing

Chassis or Secondary Conductor

Table 1: Ratings for selected area

Note: This table is unofficial and for reference only. Be

2. Leakage Current Test

Exposed Accessible Part

Measuring Method: (Power ON)

Table 2: Leakage current ratings for selected areas

Leakage Current (i)

Earth Ground (B) to:

0.15 F CAP. & 1.5 k

STANDARD NOTES FOR SERVICING

How to Remove / Install Flat Pack-IC

1. The output pin of the 3 pin Regulator ICs is

1. Prepare the hot-air flat pack-IC desoldering

2. For other ICs, pin 1 and every fifth pin are

3. Bottom of the flat pack-IC is fixed with glue to the

Pb (Lead) Free Solder

4. Release the flat pack-IC from the CBA using

Pb free mark will be found on PCBs which use Pb

With Soldering Iron:

3. The flat pack-IC on the CBA is affixed with glue, so

1. Using desoldering braid, remove the solder from

3. Bottom of the flat pack-IC is fixed with glue to the

With Iron Wire:

1. Using desoldering braid, remove the solder from

1. Using desoldering braid, remove the solder from

2. Affix the wire to a workbench or solid mounting

2. The mark on the flat pack-IC indicates pin 1.

3. While heating the pins using a fine tip soldering