Gear Coupling Catalogue PDF

JW
Gear
In This Section:
C Types Continuous Sleeve
G
Nyflex and Mite

Dentex
F Types Flanged Sleeve
R Types Rigid Adjustable
Coupling Grease
www.lovejoy-inc.com
115
G-1
G-
JW
Gear
G
Safety Warning
When using Lovejoy products, you must follow these instructions and take the following precautions. Failure
to do so may cause the power transmission product to break and parts to be thrown with sufficient force to
cause severe injury or death.
Refer to this Lovejoy Catalog for proper selection, sizing, horsepower, torque range, and speed range
of power transmission products, including elastomeric elements for couplings. Follow the installation
instructions included with the product, and in the individual product catalogs for proper installation of power
transmission products. Do not exceed catalog ratings.
During start up and operation of power transmission product, avoid sudden shock loads. Coupling assembly
should operate quietly and smoothly. If coupling assembly vibrates or makes beating sound, shut down
immediately, and recheck alignment. Shortly after initial operation and periodically thereafter, where
applicable, inspect coupling assembly for: alignment, wear of elastomeric element, bolt torques, and flexing
elements for signs of fatigue. Do not operate coupling assembly if alignment is improper, or where applicable,
if elastomeric element is damaged, or worn to less than 75% of its original thickness.
Do not use any of these power transmission products for elevators, man lifts, or other devices that carry
people. If the power transmission product fails, the lift device could fall resulting in severe injury or death.
For all power transmission products, you must install suitable guards in accordance with OSHA and
American Society of Mechanical Engineers Standards. Do not start power transmission product before
suitable guards are in place. Failure to properly guard these products may result in severe injury or death
from personnel contacting moving parts or from parts being thrown from assembly in the event the power
transmission product fails.
If you have any questions, contact the Lovejoy Engineering Department at 1-630-852-0500.
G-2
116
630-852-0500
Gear
Table of Contents
Running
Page No.
Section
Page No.
www.lovejoy-inc.com
117
Overview.......................................................................................................................................................118 ............................G-4
Selection Process .........................................................................................................................................126 ..........................G-12
Application Service Factors > Selection Data ..............................................................................................127 ..........................G-13
Gear Coupling Selection Worksheet ............................................................................................................128 ..........................G-14
Continuous Sleeve > Cut Away ....................................................................................................................129 ..........................G-15
C and CFR Type > Performance / Dimensional Data ...................................................................................130 ...................G-16 / 17
CMM Type > Performance / Dimensional Data ............................................................................................132 ...................G-18 / 19
CFS Type > Performance / Dimensional Data .............................................................................................134 ...................G-20 / 21
CSPCR Type > Performance / Dimensional Data ........................................................................................136 ...................G-22 / 23
CCS Type > Performance / Dimensional Data .............................................................................................138 ...................G-24 / 25
CSHP Type > Performance / Dimensional Data ...........................................................................................140 ...................G-26 / 27
Nylex and Mite Type > Performance / Dimensional Data........................................................................142 .................. G-28 / 29
Dentex Type > Performance / Dimensional Data .......................................................................................144 ...................G-30 / 31
C Universal Hub > Dimensional Data ...........................................................................................................146 ..........................G-32
Flanged Sleeve > Cut Away .........................................................................................................................147 ..........................G-33
F Type > Performance / Dimensional Data...................................................................................................148 ...................G-34 / 35
FFR Type > Performance / Dimensional Data ..............................................................................................150 ...................G-36 / 37
FFS Type > Performance / Dimensional Data ..............................................................................................152 ...................G-38 / 39
FHD Type > Performance / Dimensional Data .............................................................................................154 ...................G-40 / 41
FHDFR Type > Performance / Dimensional Data.........................................................................................156 ...................G-42 / 43
FHDFS Type > Performance / Dimensional Data .........................................................................................158 ...................G-44 / 45
FMM Mill Type > Performance / Dimensional Data ......................................................................................160 ...................G-46 / 47
FMM Mill Motor Type > Performance / Dimensional Data ............................................................................162 ...................G-48 / 49
FSL Type > Performance / Dimensional Data ..............................................................................................164 ...................G-50 / 51
FSXL Type > Performance / Dimensional Data ............................................................................................166 ...................G-52 / 53
FSPCR Type > Performance / Dimensional Data.........................................................................................168 ...................G-54 / 55
FLEF Type > Performance / Dimensional Data ............................................................................................170 ...................G-56 / 57
FRR Type > Performance / Dimensional Data .............................................................................................172 ...................G-58 / 59
FLA Type > Performance / Dimensional Data ..............................................................................................174 ...................G-60 / 61
FLAFR Type > Performance / Dimensional Data .........................................................................................176 ...................G-62 / 63
FLAMM and FLAMMFR Type > Performance / Dimensional Data ...............................................................178 ...................G-64 / 65
FA Type > Performance / Dimensional Data.................................................................................................180 ...................G-66 / 67
RA and RAHS Type > Performance / Dimensional Data ..............................................................................182 ...................G-68 / 69
F Universal Hub and Puller Holes > Dimensional Data ................................................................................184 ..........................G-70
F Flange and Hub Gap Details > Dimensional Data ....................................................................................185 ..........................G-71
Continuous Sleeve > Overview ....................................................................................................................186 ..........................G-72
Flanged Sleeve > Overview .........................................................................................................................188 ..........................G-74
Standard Flanged Sleeve Maximum Bores Inch / Metric > Dimensional Data .............................................190 ..........................G-76
Rigid Hub Maximum Bores Interference Fit > Dimensional Data .............................................................191 ..........................G-77
Coupling Grease...........................................................................................................................................192 ..........................G-78
G-3
Gear
Overview
Lovejoy / Sier-Bath Continuous Sleeve and Flanged Sleeve Couplings
Continuous Sleeve Series
Flanged Sleeve Series
Features
Features
Simple and inexpensive all steel type of gear coupling constructed with a
single sleeve and 2 hubs
Patented Vari-Crown tooth form for long coupling life

Precision cut 20 pressure angle gear teeth with minimum backlash
Comparatively simple installation
All steel sleeves and hubs (stainless steel available)
Precision cut 20 pressure angle gear teeth with minimum backlash
Designs for applications requiring horizontal and vertical orientation
Most standard configurations are available as stock items
Most standard configurations are available as stock items
Angular misalignment of 1/2 per gear mesh (flex-plane)
Angular misalignment of 1-1/2 per gear mesh (flex-plane) up to size 5.5,

3/4 for sizes 6 and above
Sizes 7/8 through 12, to accommodate bore sizes up to and including

12.50 inches
Interference fit (standard) and Clearance fit on bores are available
Coupling sizes available through size 30 to accommodate bore sizes up

to and including 44 inches
Load Capacities range from 2,500 in-lbs up to 2,520,000 in-lbs
Interference fit (standard) and Clearance fit on bores are available
Designs for applications requiring horizontal and vertical orientation,

full-flex, flex-rigid, mill-motor, disengagement, sliding hubs, Shear Pin,
floating shaft, and spacers
Exposed bolts standard on all sizes, shrouded available by request up

to size 6
Load capacities range from 7,600 in-lbs up to 47,269,000 in-lbs
Patented and tested BUNA N seal design with reinforced washers

bonded to the inside edges which positively retain lubricant and seal the
interior from outside contaminants
Flanged sleeve couplings are interchangeable with industry standards
Reinforced rubber seals with snap rings to hold in lubricant
Piloted gear fit for higher speeds and less vibration
Two snap rings made of hardened spring steel which securely hold the
coupling together, are easy to install or remove, yet withstand 100,000
pounds of end thrust
Labyrinth all steel seal design in FL series
Standard bolts supplied by Lovejoy are treated to be corrosion resistant
Inch and Metric bore sizes available
Inch and Metric bore sizes available
Standard Types and Sizes
Misalignment and End-Float Capability
Lovejoy / Sier-Bath couplings are stocked in an assortment of configurations

which include C and F standard hubs and sleeves, Mill Motor hubs, Vertical
style, Floating Shaft, and Spacer designs. Lovejoys superb engineering
staff make it possible to support many additional coupling types such as the
Brakedrum type, Sliding Hub type, Shear Pin type, Jordan type, and custom
lengths for non standard shaft separations. Additional size ranges and
designs to meet unusual application requirements can also be manufactured
by Lovejoy to meet market demands. Material can range from standard
steel to alloy steel and even stainless steel. The exceptional simplicity of the
Lovejoy coupling design make this all possible.
The basic principle of Lovejoy / Sier-Bath C and F type couplings is similar

to that of other conventional flexible gear couplings. While it is desirable to
align shafts as accurately as possible, the purpose of any flexible coupling
is to absorb probable angular, parallel, and axial (end-float) misalignment.
Lovejoy/Sier-Bath couplings utilize a unique gear tooth geometry developed
specifically to resolve issues with shaft misalignment and accommodate
from 1/2 to 1-1/2 per gear mesh or flex plane. The hub teeth are fully
crowned to provide for a larger contact area and lower stresses under
misaligned conditions. The crowned tooth design also eliminates most of
the end loading that occurs on straight gear teeth under misalignment.
WARNING
You must refer to page G-2 (Page 116) for Important Safety Instructions and
Precautions for the selection and use of these products. Failure to follow the
instructions and precautions can result in severe injury or death.
G-4
118
630-852-0500
Gear
Overview
Lovejoy / Sier-Bath Nyflex and Mite
Lovejoy / Sier-Bath Nylon couplings are compact and require no
lubrication. They operate over a wide temperature range at speeds up
to 5,000 RPM and are effectively used in applications such as Motor/
Generator sets, pump sets, and many light to medium duty industrial
coupling applications.
No lubricants are ever required, eliminating the need for seals. The resilient
nature of the nylon material makes the contact of the hubs and sleeves
almost frictionless. Since no lubrication is used, the coupling can readily be
adapted to many applications including vertical and blind installations where
the slip-together components offer easy inspection and adjustment.
When completely assembled, the Mite coupling weighs less than 1lb and
the Nyflex only 3.50 lbs. Weights for Dentex couplings can be found on
page G-30.
Features
Molded nylon sleeve
Nylon Sleeve
Resilient,
lightweight,
abrasion and
corrosion resistant
nylon is accurately
molded to mesh
precisely with
hubs. Their
almost frictionless
properties eliminate
the need for
lubrication.
2 Hubs
Sintered iron is
standard in the
Nyflex and Mite.
Teeth are crowned
to provide greater
misalignment
capacity and to
prevent gouging
of Nylon sleeve.
Maintain 0.13 inch
spacing between
hubs.
No internal frictional loss or heat buildup

Minimum backlash
High ambient temperature allowed
Resistance to dirt, moisture, most chemicals
Low maintenance (no seals, lubricant, retainers)
High torque, low intertia
Standard bores are available
Dentex / Dentex FL - The Flexible Coupling

Features
Compensation of axial, radial and angular misalignment
of shafts through double cardanic action
Simple and easy assembly
High electrical insulating property
High thermal stability
No maintenance
www.lovejoy-inc.com
119
G-5
2 Spirolox
Retaining Rings
Sleeve is securely
held on the hubs
by these springsteel retaining
rings. They can
be removed in
seconds, yet theyll
withstand 5,000 lbs
endthrust.
Operationally, the coupling offers a minimum backlash solution that will

operate in ambient temperature environments from -40 to 150 F. Nylon
Sleeve couplings have precision molded sleeves and hubs with no bolts,
pins, flanges, or protrusions to affect balance or safety. The nylon sleeve
permits misalignment up to 5 for Dentex and Nyflex couplings and 3 for
the Mite.
Gear
Overview
Lovejoy / Sier-Bath Continuous Sleeve
Series Couplings
Standard C Type
Basis for all types of Lovejoy / Sier-Bath Continuous Sleeve
Couplings
C Type
CFR Type
Low profile compact design is easy to implement
Section Pages G-16 and G-17
Single (flex-rigid) or double (flex-flex) engagement
Mill Motor CMM Type

Designed with longer universal hub on one end to accommodate
straight or tapered shafts
Standard hub and sleeve on the other end
Universal hub bored to customer specifications
CMM Type
Available with longer universal hubs on both ends
Floating Shaft CFS Type

Two flex-rigid couplings connected by an intermediate shaft
Increased capability to accommodate parallel misalignment
Allows for longer shaft separations
CFS Type
Spacer CSPCR Type

Drop-out spacer design allows for ease of maintenance without
disturbing the equipment mountings
Spacer has rigid teeth to mate with sleeves on each coupling
Increased capability to accommodate parallel misalignment
Allows for longer shaft separations
CSPCR Type
Cut-out Shifter CCS Type

Designed for quick disengagement between the driver and driven
equipment
Special seal in disengagement hub to prevent undue friction when
hub turns in sleeve
Widely used on dual drive operations and equipment operating in
tandem
Available with pins to maintain sleeve in engaged and disengaged
positions
CCS Type
Shifting mechanisms available upon request
Shear Pin CSHP Type

Designed to limit and protect against excessive torque or sudden
shock loads
Sheer pins designed and manufactured for predetermined loads
Pins are inserted in hardened bushings to minimize wear
CSHP Type
Easy to install new pins

For Flanged FSHP Style see page G-8
G-6
120
630-852-0500
Gear
Overview
Lovejoy / Sier-Bath Flanged Sleeve Series
Couplings
Standard F Type
Double engagement (F flex-flex) for parallel and angular
misalignment
Single engagement (FFR flex-rigid) accommodates angular
misalignment only and is ideal for floating shaft applications
Industry standard flange bolt patterns
F Type
FFR Type
FHD Type

FRR Type
FARR Type

Contact Lovejoy Technical Support
FHD Type standard for sizes 10 through 30 (other sizes available

upon request)
Rigid-Rigid FRR Type

Designed for connecting two rigidly mounted shafts with no
misalignment capability
Used for cantilevered loads such as gear boxes that hang off
conveyor systems
Alloy steel available for greater strength (FARR)
Mill Motor FMM Type

First hub designed with longer universal hub on one end to
accommodate straight or tapered shafts
FMM Type
Second hub bored to customer specifications
Section Pages G-46, G-47,

G-48 and G-49
Standard design accommodates AISE Mill Motor frame sizes

Sleeves and second hub are standard
Floating Shaft FFS Type

Two flex-rigid couplings connected by an intermediate shaft
Increased ability to accommodate parallel misalignment
FFS Type
Section Pages G-38
and G-39
Accommodate longer shaft separations

Standard construction with rigid hubs on outboard (equipment)
shafts, flex on inboard (floating) shaft
FHDFS Type
Section Pages G-44
and G-45
Rigid hubs inboard (on floating shaft) available upon request
Spacer FSPCR Type

Drop-out spacer design allows for ease of maintenance without
disturbing the equipment mountings
FSPCR Type
Lightweight construction reduces load on equipment bearings
www.lovejoy-inc.com
121
G-7
Alloy Rigid-Rigid FARR Type

Longer piloted hubs maintain rigidity and concentricity
Gear
Overview
Slide FSL and FSLX Types
Allows for a predetermined amount of axial slide
Longer hubs and sleeves available to accommodate additional
slide capacity
FSL Type
FSLX Type
Section pages G-50, G-51,

G-52 and G-53
Custom slide lengths available
Shear Pin FSHP and FSHPB Types

Designed to limit and protect equipment against excessive torque
or sudden shock loads
Shear pins designed and manufactured to shear at predetermined
torque loads
FSHP and FSHPB Type

Pins are inserted in hardened bushings to minimize wear
Easy to install new pins

Available with bearing support to maintain alignment after the pins
shear
Standard Vertical FVX Type

Designed for use with vertical shafts
FV and FVX Type

Vertical kit prevents shafts from contacting each other

Maintains ability to accommodate misalignment
Available in vertical floating shaft design
Limited End Float FLEF Type

FLEF Type
Designed for equipment with sleeve bearings
Section pages G-56 and G-57
Designed to limit axial travel of the rotor in the motor and prevent
the rotor from coming into contact and damaging sleeve bearings
G-8
122
630-852-0500
Gear
Overview
Lovejoy / Sier-Bath All Metal Labyrinth Seal
Series Couplings
All AISI 4140 Alloy Steel Design

No rubber seals metal labyrinth design
Standard with exposed bolts
Fully interchangeable with Industry standards
Ideal for higher temperature applications
Standard FLA Type

Double engagement (F flex-flex) for parallel and angular misalignment
FLA Type
FLAFR Type
FLAMM Type
FLHD Type
Contact Lovejoy
Technical Support
Single Engagement FLAFR Type
Single engagement (FFR flex-rigid) accommodates angular

Mill Motor FLAMM Type

Lovejoy Forged Steel Series

Standard FLHD Type
Piloted Sleeves
Exposed Bolts Standard
Excellent for high torque at low speeds
Bore range from 7.75 inches up to 44.88 inches
Torque capacity up to 54,390,000 in-lbs
Alloy Steel (AISI 4140) construction available
Single Engagement FLHDFR Type

FLHDFR Type Contact Lovejoy
Technical Support
Capacities the same as FHD

Ideal for heavy duty floating shaft applications
www.lovejoy-inc.com
123
G-9
Gear
Overview
Lovejoy Alloy Steel Series Couplings
All alloy steel construction
Fully molded seals maintain lubricant retention under misalignment
conditions
Exposed bolts are standard, shrouded bolts are optional
Standard FA Type
Double engagement (F flex-flex) for parallel and angular
misalignment
FA Type
FAFR Type
Contact Lovejoy
Technical Support
Single engagement FAFR Type

Single engagement (FFR Flex-Rigid) accommodates angular
Mill Motor FAMM Type

FAMM Type

Contact Lovejoy
Technical Support
Additional Specialty Coupling Types

Stainless Steel
Nylon Sleeves
High Speed RAHS Type
Brake Drum FBD and FBW Types
Insulated FI Type
Vertical Floating Shaft FVFS Type
F Style Cutout Shifter FCS Type
G-10
124
630-852-0500
Gear
Overview
Vari-Crown Tooth Form
Straight
With straight hub teeth, there is a high concentration of load under
misaligned conditions. As misalignment increases, more of the load is
carried by the ends of the teeth, resulting in premature breakdown and
coupling failure.
Conventional Crown
Lovejoy / Sier-Bath Vari-Crown

The Sier-Bath Vari-Crown tooth form has a crown at the center of the tooth
which is similar to a conventionally crowned tooth coupling. However,
as soon as misalignment occurs, the transmitted torque is carried on a
flattened area of the hub tooth which is considerably broader and stronger
than the conventionally crowned tooth form. Note the larger contact area
and reduced stress area of the Vari-Crown tooth form.
Patented Vari-Crown Tooth Form for Long Life

Facts
Constant Velocity Power Transmission

1
It can be shown that bodies with the smallest relative curvature have
the largest area of contact under load, or specifically, a body with the
largest radius of curvature has the largest area of contact with another
body when under load. More importantly, under a given load the bodies
with the greater radii of curvature have lower induced surface contact
stresses.
Gear tooth couplings have fewer teeth in contact as misalignment
increases.
Lower Stresses
Lovejoy / Sier-Baths solution to these facts was the development of the
patented Vari-Crown tooth form. The Vari-Crown tooth form is a curve
with constantly changing radii of curvature. The tooth contact area
under misaligned conditions has a much larger radius of curvature than
conventional crowning. The contact area is larger, thus reducing the unit
stress.
Note:
Lovejoy / Sier-Bath produces the Vari-Crown tooth form by a generating

method maintaining the necessary characteristics for conjugate tooth action,
which are:
1. Constant normal base pitch at any position on the crowned teeth.
2. Correct pressure angle matching of the normal to the curved surface and
the sleeve surface at any position of misalignment.
Less Backlash
The tooth design requires less backlash for a given angle of misalignment
than the conventional or circular arc crown. In many applications this is a
desirable feature in a gear tooth coupling.
N 1 indicates: Hertzs study of contact stresses of curved surfaces.
www.lovejoy-inc.com
125
G-11
Some manufacturers use a conventionally crowned hub tooth known

by various trade names. Regardless of the nomenclature, however, the
contour of the tooth is a segment of an arc. Under all operating conditions,
equal or similar contact areas between the hub teeth and the sleeve teeth
exist.
Gear
Selection Process
Gear Coupling Selection Process
Factors Affecting Selection
The following is a list of the information necessary to assist in making a coupling
selection. Not all of these items will come into play in all selection processes. These
items include, but are not limited to:
Application related:
s Application details
s Type of motor and driven equipment
s Motor horsepower or KW
s Operating/coupling speed
s Shaft sizes and separation
s Space and size constraints
s Environment (temperature, chemicals, etc)
s Balance requirements
s Special modifications
Steps In Selecting A Gear Coupling

Refer to the gear coupling specifications charts displayed with each type of coupling
throughout the Gear Coupling Products section of this catalog. The pictures and charts
provide visualization, specifications, and dimensional data for Lovejoys wide range of gear
coupling products. Typically start with an F Type flanged gear coupling (page G-34) or a C
Type continuous sleeve gear coupling (page G-16) and proceed from there.
Step 1: Review the gear coupling series and type as selected to ensure the selection
meets application requirements.
Step 2: Determine the nominal application torque in inlbs by using the following
formula:
Application Torque ( inlb ) = (HP x 63025)
RPM
or
Nm = (KW x 9550)
RPM
Step 3: Review the Application Service Factor chart for the service factor number
associated with the application where this coupling will be used. Multiply the
application torque by the application service factor to determine the total
torque required for the coupling selection.
Step 4: Compare the required total torque value with the nominal torque capacity
listed in the Gear Coupling Selection chart for the desired coupling type.
Step 5: Check that the maximum bore size and the maximum RPM of the coupling
type selected to ensure the coupling will meet these application requirements.
Step 6: Note any special requirements including the BSE dimension for floating shaft
and spacer types, shear pin torque, slide coupling details, mill motor tapered
shaft data, and any other pertinent information.
Consult with Lovejoy Technical support or Engineering for any unique application
concerns.
Selection Example (Flanged Gear Coupling)

Application Data: This sample application calls for a coupling to connect the output
side of a reducer gearbox to a dredge pump. There is a 400 HP electric motor,
running at 3,600 RPM driving the gearbox which has a 10:1 speed reduction. The
gearbox has a 6 inch diameter shaft, the pump has a 6-1/2 inch diameter shaft. There
is an angular misalignment potential of slightly more than 1.
Please note that any speed decrease at the reducer (gear box) will cause an
increase in the application torque.
Application Torque ( in-lbs ) =
(HP x 63025) = (400 x 63025) = 70,028 in-lbs
RPM
360
Step 1: Since C Type gear couplings are only capable of 1/2 misalignment per flex
plane, the F Type coupling is selected. The F Type coupling is capable of
accommodating 1-1/2 per flex plane. Note, it is highly recommended that
couplings are installed at no more than 20% of the allowable misalignment
since the alignment often changes during operation.
Selection Torque = Application Torque x Service Factor =

70,028 x 2.0 = 140,056 in-lbs
An F 3.5 coupling is rated at 151,200 in-lbs and could easily accommodate
the torque requirement, however, to accommodate the 6-1/2 inch pump
shaft diameter the selection of an F 5E size coupling will be necessary.
The F 5 coupling is rated at 434,700 in-lbs and may seem to be too
large or overrated for this application, but the larger size is necessary to
accommodate the shaft size.
Step 2: Refer to page G-34 and G-35 for Flanged series (F Type) double
engagement, or flex-flex, coupling information. The bore size and torque
should be addressed interactively when selecting a coupling size.
Step 3: The application service factor can be found on page G-13. Application
service factors are multipliers assigned to assorted applications for the
purpose of guiding the coupling selection process to a torque rating that will
prevent premature failure caused by the characteristics of that application.
For this sample application, note that the service factor for a dredge pump
application is 2.0.
Step 4: Calculate the torque requirements for the application using the formula:
Design Torque ( inlbs ) = HP x 63025
RPM
or
Nm = (KW x 9550)
RPM
Selection Torque = Application Torque x Service Factor
In this example, a gearbox is in use that reduces the operating speed
where the coupling is being used from 3,600 RPM on the input side to 360
RPM on the gearbox output side.
G-12
Step 5: Confirm that the RPM is within range specified for the selected coupling. The chart
shows the F 5 has a 2,500 RPM maximum speed and this will accommodate the
360 RPM speed requirement on the output side of the gearbox.
Step 6: Please refer to the coupling specifications on page G-34 and G-35. Note
that F 5E couplings are manufactured with interference fits and exposed
bolts as standard. When contacting your sales representative, the
description for this coupling would be an F 5E gear coupling and include the
bore size, keyway information, and shaft separation. Also, provide a list of
any requirements that might supersede the coupling defaults.
Special Note: If the shaft separation is greater than specified in the chart on Page
G-35, refer to the Floating shaft or Spacer style couplings on pages G-39 or G-55. If
the desired shaft separation, or BSE, is not listed, contact Lovejoy Technical Support
for assistance.
Please refer to the Lovejoy website for installation instructions and lubrication
requirements for gear couplings.
126
630-852-0500
Gear
Application Service Factors
Selection Data
Application Service Factors
Machine Tools
Bending Roll............................................2.0
Punch Press, Gear Driven ......................2.0
Tapping Machines ...................................2.0
Main Drives .............................................1.5
Auxiliary Drives .......................................1.5
Metal Mills
Draw BenchCarriage ...........................2.0
Draw BenchMain Drive........................2.0
Forming Machines ..................................2.0
Slitters .....................................................1.5
Table Conveyors
Non-Reversing .................................2.25
Reversing ...........................................2.5
Wire Drawing &
Flattening Machine...............................2.0
Wire Winding Machine ..........................1.75
Metal Rolling Mills
Blooming Mills ........................................ 2.5
Coilers, hot mill........................................2.0
Coilers, cold mill ......................................1.5
Cold Mills.................................................2.0
Cooling Beds.........................................1.75
Door Openers .........................................2.0
Draw Benches.........................................2.0
Edger Drives .........................................1.75
Feed Rolls, Reversing Mills ....................3.5
Furnace Pushers.....................................2.5
Hot Mills ..................................................3.0
Ingot Cars ...............................................2.5
Kick-outs .................................................2.5
Manipulators ...........................................3.0
Merchant Mills .........................................3.0
Piercers ...................................................3.0
Pusher Rams ..........................................2.5
Reel Drives ...........................................1.75
Reel Drums .............................................2.0
Reelers ....................................................3.0
Rod and Bar Mills....................................3.0
Roughing Mill Delivery Table...................3.0
Runout Tables .........................................2.5
Saws, hot & cold .....................................2.5
Screwdown Drives ..................................3.0
Skelp Mills ...............................................3.0
Slitters .....................................................3.0
Slabing Mills ..........................................1.75
Soaking Pit Cover Drives ........................3.0
Straighteners...........................................2.5
Tables, transfer & runout ........................2.5
Thrust Block ............................................3.0
Traction Drive ..........................................3.0
Tube Conveyor Rolls...............................2.5
Unscramblers ..........................................2.5
Wire Drawing ........................................1.75
Mills, Rotary Type
Ball ........................................................2.25
Dryers & Coolers.....................................2.0
Hammer ................................................1.75
Kilns ........................................................2.0
Pebble & Rod ..........................................2.0
Pug ........................................................1.75
Tumbling Barrels .....................................2.0
Mixers
Concrete Mixers, Continuous..................1.5
Concrete Mixers, Intermittent ..................2.0
Oil Industry
Oil Well Pumping.....................................2.0
Rotary Kilns .............................................2.0
Paper Mills
Agitators, Mixers .....................................1.5
Barker Auxiliaries, Hydraulic ...................2.0
Barker Mechanical ..................................2.0
Barking Drum Spur
Gear Only...........................................2.0
Beater & Pulper.....................................1.75
Bleacher ..................................................1.0
Calenders................................................2.0
Calenders, Super ....................................1.5
Chippers ..................................................2.5
Coaters....................................................1.0
Converting Machines,
except Cutters, Platers.........................1.5
Conveyors ...............................................1.5
Couch Roll ............................................1.75
Cutters, Platters ......................................2.0
Cylinders ...............................................1.75
Disc Refiners.........................................1.75
Dryers....................................................1.75
Felt Stretcher ........................................1.25
Felt Whipper...........................................2.0
Jordans .................................................1.75
Line Shaft ................................................1.5
Log Haul ..................................................2.0
Pulp Grinder ..........................................1.75
Press Roll ................................................2.0
Reel .........................................................1.5
Stock Chests ...........................................1.5
Suction Roll ...........................................1.75
Washers & Thickeners ............................1.5
Winders ...................................................1.5
Printing Presses...........................................1.5
Pumps
Centrifugal ...............................................1.0
Reciprocating
Single Acting 3 or more
Cylinders ...........................................1.5
Double Acting 2 or more
Cylinders ...........................................2.0
Rotary, Gear Type, Lobe
Vane ...................................................1.5
Rubber Industry
Mixer .......................................................2.0
Rubber Calender.....................................2.0
Screens
Rotary, Stone or Gravel ..........................1.5
Steering Gear ...............................................1.0
Stokers ..........................................................1.0
Textile Industry
Dryers......................................................1.5
Dyeing Machinery ...................................1.5
Windlass .......................................................2.0
Notes: N 1 indicates: If people are transported, Lovejoy does not recommend and will not warranty the use of the coupling.
N Values contained in the table should be used as a general guide and are to be applied to smooth power sources such as electric
motors and steam turbines.
N For drives involving internal combustion engines add 1.0 to the values listed.
www.lovejoy-inc.com
127
G-13
Agitators
Pure Liquids ............................................1.0
LiquidsVariable Density .......................1.0
Blowers
Centrifugal ...............................................1.0
Lobe ........................................................1.2
Can Filling Machines ...................................1.0
Car Dumpers ................................................2.0
Car Pullers, Intermittent Duty .....................1.5
Compressors
Centrifugal ...............................................1.0
Reciprocating ..........................................2.2
Multi-Cylinder ..........................................2.0
Single Cylinder ........................................2.0
Conveyors, Uniformly Loaded or Fed
Assembly ................................................1.2
Belt ..........................................................1.2
Screw ......................................................1.2
Conveyors, Heavy Duty
Not Uniformly
Fed Assembly .........................................1.5
Belt ..........................................................1.5
Oven........................................................1.5
Reciprocating ..........................................2.0
Screw ......................................................1.5
Shaker .....................................................1.5
Cranes and Hoists1
Main Hoists .............................................2.0
Reversing ................................................2.0
Skip Hoists ..............................................2.0
Trolley Drive ............................................2.0
Bridge Drive ............................................2.0
Crushers
Ore ..........................................................3.0
Stone .......................................................3.0
Dredges
Conveyors ...............................................2.0
Cutter Head Drives ................................2.0
Maneuvering Winches ............................2.0
Pumps .....................................................2.0
Fans
Centrifugal ...............................................1.0
Cooling Towers Forced Draft ..................1.5
Feeders
Screw ......................................................1.5
Generators
Not Welding.............................................1.0
Welding ...................................................1.5
Hammer Mills................................................2.0
Laundry Washers
Reversing ................................................1.5
Lumber Industry
BarkersDrum Type ..............................2.0
Edger Feed ............................................2.0
Live Rolls.................................................2.0
Log HaulIncline....................................2.0
Log HaulWell Type ..............................2.0
Off Bearing Rolls .....................................2.0
Planer Feed Chains ..............................1.75
Planer Tilting Hoist ................................1.75
Planer Floor Chains ..............................1.75
Slab Conveyor ........................................1.5
Sorting Table ...........................................1.5
Trimmer Feed..........................................1.5
Gear
Selection Worksheet
Customer Name:____________________________________________________ Contact Name: _____________________________________________
Phone Number:_____________________________________________________ Email Address: ______________________________________________
1. Type of Driver (Electric Motor, Combustion Engine, Gearbox, etc.) : ___________________
For combustion engines, define type

Gasoline, Diesel, Natural Gas, etc. : ______________ Number of cylinders _______
2. Driver Horse Power : ____________
3. Driver or Gearbox output RPM : _____________
Retrieve the Application Service Factor from Page G-13 : ______________ then
calculate the Selection Torque using the following formula:
Torque (in-lbs) = HP x 63025 x Service Factor = Selection Torque = ____________ in-lbs
RPM
4. Driver Shaft Diameter : _________ Keyway size : KW Height _________ KW Width _________
Specify Clearance Fit, Interference Fit, Metric (P7, H7, etc), Shaft Locking Device, and Set Screw or No Set Screw
5. Driver Usable Shaft Length : ___________ (Measure from the end of the shaft to any obstruction)
For additional bore and

keyway information, see the
Engineering Data Section
of the Power Transmission
Products Catalog
6. Distance between shaft ends (BSE) : _______________

7. Type of Driven Equipment : _______________________________________
8. Driven Shaft Diameter : _________ Keyway size : KW Height _________ KW Width _________
Specify Clearance Fit, Interference Fit, Metric (P7, H7, etc), Shaft Locking Device, and Set Screw or No Set Screw
9. Driven Usable Shaft Length : ___________ (Measure from the end of the shaft to any obstruction)
10. Total Mounting Length : ______________ (Advise of any obstructions, walls, beams, guards, pipes, etc.)
11. For Tapered Shafts specify the following
Minimum or Maximum Taper diameter: _________________________________
Taper Length: ___________ T (Taper Inch per Foot) : _____________________
Gap or Hub Overhang amount: _______________________________________
Locknut Width: ___________ Size of nut cross corners: ___________________
Thread Size: _____________ Thread Length: ___________________________
Washer Diameter (if used) : ____________ Washer Width: ________________
Lovejoy, Inc.
World Headquarters
2655 Wisconsin Avenue
Downers Grove, IL 60515
G-14
Send this form to:

appleng@lovejoy-inc.com
or fax to: 800-446-0878
128
630-852-0500
Gear
Continuous Sleeve
Cut Away
Lovejoy / Sier-Bath Continuous Sleeve Gear Couplings
One-piece steel sleeve Internal

teeth run full working length
Lubrication holes (2)
Draw-off holes (Optional)
Steel hubs
G
Reinforced rubber lubrication
seals held in by snap rings
Keyway
Oil-hardened spring steel snap rings

positioned by grooves in sleeve
Gear teeth precision-cut, evenly spaced
The One-Piece Sleeve Gear Coupling
www.lovejoy-inc.com
129
G-15
Gear
C and CFR Type
Performance Data
C Type Flex-Flex Couplings
The C Type coupling consists of two flex hubs, one sleeve and one accessory kit
consisting of seals and snap rings.
CFR Type Flex-Rigid Couplings

The CFR Type coupling consist of one flex hub, one rigid hub, one sleeve, one
accessory kit consisting of seals and snap rings.
Features
Simple and inexpensive type of gear coupling
All steel sleves and hubs
Reinforced rubber seals with snap rings to hold lubricant in place
Available as vertical and horizontal couplings
Wide variety of special variations such as full-flex, flex-rigid mill motor
Standard configurations are available of the shelf
C - CFR Performance Data

ID1 - ID2
Nominal
Maximum
Flex & Rigid
Flex & Rigid
Torque
Speed
Max Bore
Rough Stock
Unbal
Size
in-lb
Angular
Misalignment
Bore
mm
in
Degrees
RPM
RPM
in
mm
lbs
kg
in
mm
6,000
18,000
1.25
31
0.44
11
0.005
0.13
7,600
900
5,000
15,000
1.63
42
0.63
16
0.007
0.18
1/2
20,200
2 300
4,200
12,600
2.13
56
0.73
19
13
0.007
0.18
per Mesh
2,500
1.5
2
Parallel
Misalignment
300
7/8
Nn
Bal
Weight
2.5
30,200
3 400
3,750
11,250
2.63
70
0.88
22
20
0.007
0.25
50,400
5 700
3,600
9,000
3.13
84
1.19
30
33
15
0.010
0.30
3.5
88,200
10 000
2,800
8,400
3.63
97
1.25
32
63
29
0.012
0.30
126,000
14 200
2,400
7,200
4.13
111
1.75
44
91
41
0.012
0.30
4.5
184,000
20 800
2,200
6,600
4.75
130
2.38
60
126
57
0.007
0.18
270,900
30 600
2,100
6,300
5.75
160
2.88
73
195
89
0.007
0.48
1/4
378,000
42 700
2,000
6,000
6.63
186
3.88
99
267
121
0.009
0.23
per Mesh
598,500
67 600
1,000
3,000
7.50
200
4.69
119
320
145
0.010
0.25
1,260,000
142 400
800
2,400
9.50
240
5.88
149
520
236
0.011
0.28
11
2,205,000
249 200
600
1,800
11.50
305
7.75
197
925
420
0.013
0.33
12
2,520,000
284 700
550
1,650
12.50
330
9.75
248
1,200
545
0.014
0.36
Ordering Information
Application: Driver and Driven.
Type and size of coupling, horizontal, vertical etc.
Power: Motor horspower or torque requirement.
Speed: Motor RPM or Driven RPM.
Distance between shaft ends (BSE).
Shaft sizes.
G-16
130
630-852-0500
Gear
C and CFR Type
Dimensional Data
C and CFR Type Couplings
C Type Flex-Flex Coupling
CFR Type Flex-Rigid Coupling
C and CFR Type Dimensional Data

R
OAL
LS
SL
ID1 - ID2
HL
Flex & Rigid
Flex & Rigid
Max Bore
Rough Stock
DC
BSE
G
G1
in
in
OD
HD
CBD
in
in
in
Bore
Size
in
in
in
in
in
mm
in
mm
in
in
7/8
3.75
3.13
2.00
1.00
1.25
31
0.44
11
1.50
0.13
0.13
0.38
3.31
2.00
1.94
1.5
4.59
3.75
2.53
1.27
1.63
42
0.63
16
1.81
0.19
0.13
0.50
3.75
2.38
2.25
4.88
4.25
2.56
1.28
2.13
56
0.73
19
2.06
0.19
0.13
0.50
4.75
3.25
3.00
2.5
5.72
4.75
3.06
1.53
2.63
70
0.88
22
2.25
0.25
0.25
0.75
5.50
3.94
3.75
6.88
5.50
3.75
1.88
3.13
84
1.19
30
2.63
0.25
0.25
0.75
6.63
4.75
4.75
3.5
9.25
8.75
4.00
2.00
3.63
97
1.25
30
4.25
0.25
0.25
0.75
7.50
5.38
5.50
9.50
9.00
4.63
2.31
4.13
111
1.75
44
4.38
0.25
0.25
0.75
8.75
6.25
6.50
4.5
10.38
10.25
4.88
2.44
4.75
130
2.38
60
5.00
0.25
0.25
0.75
9.50
7.25
7.25
12.25
12.25
5.75
2.88
5.75
160
2.88
73
6.00
0.25
0.25
0.75
10.75
8.25
8.12
13.38
13.00
6.50
3.25
6.63
186
3.88
99
6.38
0.25
0.25
0.75
12.25
9.50
9.25
15.38
14.88
7.50
3.75
7.50
200
4.69
119
7.25
0.25
0.38
0.88
14.00
10.50
9.75
19.00
19.00
8.13
4.06
9.50
240
5.88
149
9.25
0.25
0.50
1.00
16.25
12.63
12.25
11
22.50
22.50
8.13
4.06
11.50
305
7.75
197
11.00
0.25
0.50
1.00
19.25
15.63
15.00
12
25.00
25.00
8.38
4.19
12.50
330
9.75
248
12.25
0.25
0.50
1.00
20.50
16.50
16.00
Puller Holes are standard on sizes 4 through 12.
Puller Holes are available for sizes 7/8 through 3.5 at an additional charge.
The BSE (distance Between Shaft Ends) may vary between G and G1.
Interference bores with no set screws are standard unless otherwise specified.
Inch bores and keyway tolerances conform to ANSI / AGMA 9002-B04.
For metric bores and keyway tolerances, consult Lovejoy Engineering Section.
Larger sizes are available, please consult Lovejoy Technical Support.
www.lovejoy-inc.com
131
G-17
Gear
CMM Type
Performance Data
CMM Type Mill Motor Couplings
The CMM Type coupling consists of one standard flex hub, one
universal hub, one standard sleeve and one accessary kit consisting
of seals and snap rings.
Features
Specifically designed for mill motors with tapered bores
Universal hub counterbored for the nut on the end of the motor
shaft
One piece cylindrical sleeve for smoother, faster, quieter and and
safer operation
Quick assembly and disassembly
CMM Type Performance Data
ID1 - ID2
Nominal
Maximum Speed
Max Bore
Rough
Torque
Unbal
Bal
RPM
RPM
in
mm
in
Weight
Stock Bore
Parallel
Max Angular
Misalignment
Misalignment
Degrees
Size
in-lb
Nm
mm
lbs
kg
in
mm
7/8
2,500
300
6,000
18,000
1.25
31
0.44
11
3.2
0.005
.13
1.5
7,600
900
5,000
15,000
1.63
42
0.63
16
11
5.0
0.007
.18
20,200
2 300
4,200
12,600
2.13
56
0.73
19
19
8.6
0.007
.18
2.5
30,200
3 400
3,750
11,250
2.63
70
0.88
22
29
13.0
0.007
.18
50,400
5 700
3,600
9,000
3.13
84
1.19
30
46
21.0
0.010
.25
3.5
88,200
10 000
2,800
8,400
3.63
97
1.25
32
77
35.0
0.012
.30
126,000
14 200
2,400
7,200
4.13
111
1.75
44
109
49.0
0.012
.30
4.5
184,000
20 800
2,200
6,600
4.75
130
2.38
60
155
70.0
0.007
.18
270,000
30 600
2,100
6,300
5.75
160
2.88
73
220
100.0
0.007
.18
378,000
42 700
2,000
6,000
6.63
186
3.88
99
315
143.0
0.009
.23
1/2
1/4
Shaft sizes.
Length and taper per foot of Mill Motor shaft.
Size of nut to be used on Mill Motor (DC1 and CBD1).
Specify if keyways are to be parallel to shaft axis or tapered.
G-18
132
630-852-0500
Gear
CMM Type
Dimensional Data
CMM Type Mill Motor Couplings
Standard Type
Alternative Type
CMM Type Dimensional Data
OAL
LS
SL
ID1 - ID2
Max Bore
HL
HL1
DC
DC1
in
OD
HD
CBD
CBD 1
Rough
Size
in
1.5
2
2.5
3
3.5
4
4.5
5
6
Determined by Length of Mill Motor Hub
7/8
in
in
in
in
mm
in
in
in
3.75
in
2.00
1.00
1.25
mm
31
0.44
11
1.50
3.75
0.13
4.59
2.53
1.27
1.63
42
0.63
16
1.81
4.00
0.19
4.88
2.56
1.28
2.13
56
0.73
19
2.06
4.63
0.19
5.72
3.06
1.53
2.63
70
0.88
22
2.25
5.13
0.25
6.88
3.75
1.88
3.13
84
1.19
30
2.63
5.75
0.25
9.25
4.00
2.00
3.63
97
1.25
32
4.25
6.50
0.25
9.50
4.63
2.31
4.13
111
1.75
44
4.38
6.63
0.25
10.38
4.88
2.44
4.75
130
2.38
60
5.00
7.75
0.25
12.25
5.75
2.88
5.75
160
2.88
73
6.00
7.88
0.25
13.38
6.50
3.25
6.63
186
3.88
99
6.38
9.25
0.25
Determined by Customer Specifications
Stock Bore
in
in
in
in
in
0.13
3.31
2.00
1.94
1.63
0.13
3.75
2.38
2.25
1.88
0.13
4.75
3.25
3.00
2.75
0.25
5.50
3.94
3.75
3.25
0.25
6.63
4.75
4.75
3.88
0.25
7.50
5.38
5.50
4.50
0.25
8.75
6.25
6.50
5.13
0.25
9.50
7.25
7.25
5.50
0.25
10.75
8.25
8.13
6.50
0.25
12.25
9.50
9.25
7.75
HL1 Dimensions are the maximum lengths of Universal hubs kept in stock and altered to customer specifications. Longer length hubs are made to order.
Dimension CBD1 as shown is the maximum safe counterbore. Diameter of this counterbore is to customer specifications.
Rough bore mill motor hubs are manufactured to HL1 length with straight bores.
For metric bores and keyway, consult Lovejoy Engineering Section.
www.lovejoy-inc.com
133
G-19
Gear
CFS Type
Performance Data
CFS Type Floating Shaft Coupling
The CFS Type coupling consists of two flex-rigid (CFR) couplings

with a shaft between them. Normally the driver and driven ends
are rigid while the two center hubs connected by the center shaft
are flexible. These hubs can be reversed if necessary without
sacrificing ease of installation or disassembly.
CFS Type Performance Data

ID1 - ID2
Size
Nominal
Maximum
Flex & Rigid
Flex & Rigid
Weight
Parallel
Max Angular
Torque
Speed
Max Bore
Rough Stock
Coupling
Misalignment
Misalignment
in-lb
Nm
Unbal
Bal
RPM
RPM
Bore
in
mm
in
Only
mm
lbs
Degrees
kg
in
mm
7/8
2,500
300
6,000
18,000
1.25
31
0.44
11
10
4.5
0.005
.13
1.5
7,600
900
5,000
15,000
1.63
42
0.63
16
16
7.3
0.007
.18
20,200
2 300
4,200
12,600
2.13
56
0.73
19
26
12.0
0.007
.18
2.5
30,200
3 400
3,750
11,250
2.63
70
0.88
22
40
18.0
0.007
.18
50,400
5 700
3,600
9,000
3.13
84
1.19
30
66
30.0
0.010
.25
3.5
4
88,200
10 000
2,800
8,400
3.63
97
1.25
32
126
57.0
0.012
.30
126,000
14 200
2,400
7,200
4.13
111
1.75
44
182
83.0
0.012
.30
4.5
184,000
20 800
2,200
6,600
4.75
130
2.38
60
252
114.0
0.007
.18
270,000
30 600
2,100
6,300
5.75
160
2.88
73
390
177.0
0.007
.18
378,000
42 700
2,000
6,000
6.63
186
3.88
99
534
242.0
0.009
.23
1/2
1/4
Shaft sizes.
G-20
134
630-852-0500
Gear
CFS Type
Dimensional Data
CFS Type Floating Shaft Couplings
OAL
LS
CFS Type Dimensional Data

SL
ID1 - ID2
HL
Flex & Rigid
Flex & Rigid
Max Bore
Rough Stock
DC
BSE
G1
OD
HD
CBD
in
in
in
in
in
Min
Bore
Size
in
in
in
in
in
mm
in
mm
in
in
in
7/8
3.75
3.13
2.00
1.00
1.25
31
0.44
11
2.00
0.13
3.75
0.13
0.38
3.31
2.00
1.94
1.5
4.59
3.75
2.53
1.27
1.63
42
0.63
16
2.38
0.19
4.63
0.13
0.50
3.75
2.38
2.25
4.88
4.25
2.56
1.28
2.13
56
0.73
19
3.25
0.19
5.13
0.13
0.50
4.75
3.25
3.00
2.5
5.72
4.75
3.06
1.53
2.63
70
0.88
22
3.94
0.25
6.00
0.25
0.75
5.50
3.94
3.75
6.88
5.50
3.75
1.88
3.13
84
1.19
30
4.75
0.25
6.75
0.25
0.75
6.63
4.75
4.75
3.5
9.25
8.75
4.00
2.00
3.63
97
1.25
32
5.38
0.25
9.50
0.25
0.75
7.50
5.38
5.50
9.50
9.00
4.63
2.31
4.13
111
1.75
44
6.25
0.25
9.75
0.25
0.75
8.75
6.25
6.50
4.5
10.38
10.25
4.88
2.44
4.75
130
2.38
60
7.25
0.25
11.00
0.25
0.75
9.50
7.25
7.25
12.25
12.25
5.75
2.88
5.75
160
2.88
73
8.25
0.25
13.00
0.25
0.75
10.75
8.25
8.13
13.38
13.00
6.50
3.25
6.63
186
3.88
99
9.50
0.25
13.75
0.25
0.75
12.25
9.50
9.25
Notes: N
N
N
N
N
N
N
N
FSL Dimension is the minimum length of the floating shaft.

The BSE (distance Between Shaft Ends) vary between G and G1.
www.lovejoy-inc.com
135
G-21
Gear
CSPCR Type
Performance Data
CSPCR Type Spacer Couplings
The CSPCR Type coupling consists of two flex hubs, two sleeves, one spacer,
one accessory kit, two split seals and two lock rings.
Features
Easy removal of hubs without disturbing the mounting of connected units
Spacer teeth are rigid with a slight interference fit with the mating flex hub
Split seals on the spacer
CSPCR Type Performance Data
ID1 - ID2
Nominal
Maximum
Weight
Parallel
Max Angular
Bore
Couplings
Misalignment
Misalignment
Speed
Unbal
Only
Degrees
RPM
RPM
in
mm
in
mm
lbs
in
mm
2,500
300
6,000
18,000
1.25
31
0.44
11
3.2
0.005
.13
1.5
7,600
900
5,000
15,000
1.63
42
0.63
16
11
5.0
0.007
.18
20,200
2 300
4,200
12,600
2.13
56
0.73
19
16
7.3
0.007
.18
1/2
2.5
30,200
3 400
3,750
11,250
2.63
70
0.88
22
26
12.0
0.007
.18
per Mesh
50,400
5 700
3,600
9,000
3.13
84
1.19
30
43
20.0
0.010
.25
3.5
88,200
10 000
2,800
8,400
3.63
97
1.25
32
79
36.0
0.012
.30
126,000
14 200
2,400
7,200
4.13
111
1.75
44
115
52.0
0.012
.30
4.5
184,000
20 800
2,200
6,600
4.75
130
2.38
60
158
72.0
0.007
.18
1/4
270,000
30 600
2,100
6,300
5.75
160
2.88
73
248
113.0
0.007
.18
per mesh
378,000
42 700
2,000
6,000
6.63
186
3.88
99
340
154.0
0.009
.23
Nm
Bal
7/8
Note:
in-lb
Rough Stock
Torque
Size
Max Bore
kg
N 1 indicates: Maximum RPM of spacer coupling determined by critical speed of spacer shaft.
Shaft sizes.
G-22
136
630-852-0500
Gear
CSPCR Type
Dimensional Data
CSPCR Type Spacer Couplings
CSPCR Type Dimensional Data

OAL
LS
SL
ID1 - ID2
Min
Max Bore
Rough Stock
BSE
Min
Min
HL
DC
OD
HD
CBD
Bore
Size
in
in
in
mm
in
mm
in
in
in
in
in
in
in
7/8
6.76
2.00
1.00
1.25
31
0.44
11
4.00
3.50
1.50
0.13
0.13
3.31
2.00
1.94
1.5
7.38
2.53
1.27
1.63
42
0.63
16
4.13
3.50
1.81
0.13
0.19
3.75
2.38
2.25
8.51
2.56
1.28
2.13
56
0.73
19
4.75
4.13
2.06
0.13
0.19
4.75
3.25
3.00
2.5
in
in
9.50
3.06
1.53
2.63
70
0.88
22
5.50
4.50
2.25
0.25
0.25
5.50
3.94
3.75
11.01
3.75
1.88
3.13
84
1.19
30
6.25
5.25
2.63
0.25
0.25
6.63
4.75
4.75
3.5
15.00
4.00
2.00
3.63
97
1.25
32
7.00
6.00
4.25
0.25
0.25
7.50
5.38
5.50
15.89
4.63
2.31
4.13
111
1.75
44
7.63
6.63
4.38
0.25
0.25
8.75
6.25
6.50
4.5
17.38
4.88
2.44
4.75
130
2.38
60
7.88
6.88
5.00
0.25
0.25
9.50
7.25
7.25
20.25
5.75
2.88
5.75
160
2.88
73
8.75
7.75
6.00
0.25
0.25
10.75
8.25
8.13
21.76
6.50
3.25
6.63
186
3.88
99
9.50
8.50
6.38
0.25
0.25
12.25
9.50
9.25
Notes:
N
N
N
N
N
N

www.lovejoy-inc.com
137
G-23
Gear
CCS Type
Performance Data
CCS Type Cut-Out Shifter Couplings
The CCS Type coupling consists of two flex hubs, one special sleeve
without lubrication holes and one accessory kit which includes a special
seal for the hub that disengages to elliminate undue friction when the
disengaged hub is turning in the sleeve. Standard hub is hand packed
with grease.
Features
Permits quick disengagement of driver and driven shafts without
disassembling the coupling
Widely used on dual drives and equipment operated in tandem
Special seal for diengaging hub
Also available with pins to maintain sleeve in both engaged and
disengaged positions
CCS Type Performance Data

ID1 - ID2
Nominal
Maximum Speed
Torque
Unbal
Max Bore
Rough
Bal
Weight
Stock Bore
Parallel
Max Angular
Misalignment
Misalignment
Degrees
Size
in-lb
7/8
2,500
1.5
Nm
RPM
RPM
in
mm
in
mm
300
6,000
18,000
1.25
31
0.44
11
lbs
kg
in
mm
0.005
.13
7,600
900
5,000
15,000
1.63
42
0.63
16
Weight
0.007
.18
20,200
2 300
4,200
12,600
2.13
56
0.73
19
Determined
0.007
.18
2.5
30,200
3 400
3,750
11,250
2.63
70
0.88
22
by
0.007
.18
50,400
5 700
3,600
9,000
3.13
84
1.19
30
W & OD
0.010
.25
3.5
88,200
10 000
2,800
8,400
3.63
97
1.25
32
Dimensions
0.012
.30
126,000
14 200
2,400
7,200
4.13
111
1.75
44
supplied
0.012
.30
4.5
184,000
20 800
2,200
6,600
4.75
130
2.38
60
by
0.007
.18
270,000
30 600
2,100
6,300
5.75
160
2.88
73
Customer
0.007
.18
378,000
42 700
2,000
6,000
6.63
186
3.88
99
0.009
.23
1/2
1/4
Shaft sizes.
Dimensions of Shifter Grove (width and outside diameter).
Specify which hub will be stationary when coupling is disengaged.
G-24
138
630-852-0500
Gear
CCS Type
Dimensional Data
CCS Type Cut-Out Shifter Couplings
Disengaged Position
CCS Type Dimensional Data

R
OAL
LS
ID1 - ID2
HL
Max Bore
Rough
BSE
G
G1
OD
HD1
HD
T1
in
in
in
in
in
3.31
1.985
2.00
0.38
Stock Bore
Size
in
in
in
7/8
4.31
3.13
2.56
1.5
5.38
3.75
3.31
5.75
4.25
3.44
2.5
6.41
4.75
3.88
Specs
7.69
5.50
4.63
3.5
in
in
mm
in
mm
in
in
in
1.25
31
0.44
11
1.50
0.13
0.38
Per
1.63
42
0.63
16
1.81
0.13
0.50
Per
3.75
2.365
2.38
0.63
Cust
2.13
56
0.73
19
2.06
0.13
0.50
Cust
4.75
3.235
3.25
0.56
2.63
70
0.88
22
2.25
0.25
0.75
Specs
5.50
3.925
3.94
0.69
3.13
84
1.19
30
2.63
0.25
0.75
6.63
4.735
4.75
0.75
9.63
8.75
4.88
3.63
97
1.25
32
4.25
0.25
0.75
7.50
5.365
5.38
0.81
10.69
9.00
5.81
4.13
111
1.75
44
4.38
0.25
0.75
8.75
6.235
6.25
1.00
4.5
11.44
10.25
5.94
4.75
130
2.38
60
5.00
0.25
0.75
9.50
7.235
7.25
1.00
14.00
12.25
7.50
5.75
160
2.88
73
6.00
0.25
0.75
10.75
8.235
8.25
1.50
15.44
13.00
8.56
6.63
186
3.88
99
6.38
0.25
0.75
12.25
9.485
9.50
1.88
Notes: N
N

N

N

N

N

N

N
1 indicates: T is the length of travel to disengage sleeve.

The BSE (distance Between Shaft Ends) vary between G and G1.
www.lovejoy-inc.com
139
G-25
Gear
CSHP Type
Performance Data
CSHP Type Shear Pin Couplings
The CSHP Type coupling consists of one standard flex hub, two
piece shear hub and one set of shear pins, one standard sleeve
and accessory kit.
Features
Designed to prevent damage to connected equipment
Manufactured to shear at predetermined loads
New Pins can be quickly inserted
CSHP Type Performance Data

ID1 - ID2
Maximum
Flex or Rigid
Shear Hub
Torque
Speed
Max Bore
Max Bore
Nominal
Size
1.5
in-lb
Nm
Weight
Unbal
Bal
RPM
RPM
in
mm
in
mm
lbs
Parallel
Max Angular
Misalignment
Misalignment
Degrees
kg
in
mm
7,600
900
5,000
15,000
1.63
42
0.938
24
0.007
.18
20,200
2 300
4,200
12,600
2.13
56
1.500
38
10
0.007
.18
2.5
30,200
3 400
3,750
11,250
2.63
70
1.750
44
15
0.007
.18
50,400
5 700
3,600
9,000
3.13
84
2.250
57
23
10
0.010
.25
3.5
88,200
10 000
2,800
8,400
3.63
97
2.625
66
47
21
0.012
.30
126,000
14 200
2,400
7,200
4.13
111
3.625
92
90
41
0.012
.30
4.5
184,000
20 800
2,200
6,600
4.75
130
4.125
104
112
51
0.007
.18
270,000
30 600
2,100
6,300
5.75
160
4.500
114
177
80
0.007
.18
378,000
42 700
2,000
6,000
6.63
186
5.875
149
250
114
0.009
.23
1/2
1/4
Shaft sizes.
Specify which is the Shear Pin hub.
Specify the required shear torque.
G-26
140
630-852-0500
Gear
CSHP Type
Dimensional Data
CSHP Type Spacer Couplings
OAL
LS
CSHP Type Dimensional Data

SL
ID1
ID2
Flex or Rigid
Shear Hub
Max Bore
Size
1.5
in
in
5.28
4.38
LTB
HL
OD
HD
Max Bore
in
in
in
in
mm
in
in
in
in
in
in
2.53
1.27
1.63
42
0.938
24
1.63
2.25
0.50
1.13
3.75
2.38
5.56
4.88
2.56
1.28
2.13
56
1.500
38
1.88
2.50
0.50
1.13
4.75
3.25
2.5
6.50
5.44
3.06
1.53
2.63
70
1.750
44
2.00
2.69
0.75
1.50
5.50
3.94
7.75
6.38
3.75
1.88
3.13
84
2.250
57
2.38
3.25
0.75
1.63
6.63
4.75
3.5
8.13
8.13
4.00
2.00
3.63
97
2.625
66
4.00
3.38
0.75
1.75
7.50
5.38
9.50
9.00
4.63
2.31
4.13
111
3.625
92
4.13
4.13
0.75
2.00
8.75
6.25
4.5
9.88
9.75
4.88
2.44
4.75
130
4.125
104
4.75
4.25
0.75
2.00
9.50
7.25
11.50
11.50
5.75
2.88
5.75
160
4.500
114
5.75
5.00
0.75
2.25
10.75
8.25
13.13
13.00
6.50
3.25
6.63
186
5.875
149
6.13
6.13
0.75
2.88
12.25
9.50
5
6
Notes: N
N

N

N

N

N

Puller Holes are available for sizes 1.5 through 3.5 at an additional charge.
www.lovejoy-inc.com
141
G-27
Gear
Nyflex and Mite Type

Performance Data
Lovejoy / Sier-Bath Nylon Sleeve Gear Couplings
Nyflex and Mite Type Couplings
The Nyflex and Mite coupling consists of two sintered iron flex hubs, one Nylon sleeve and two
Spiirolox rings.
Features
No lubrication required elliminating the need for seals
Sintered Iron hubs with crowned teeth to provider greater misalignment and gouging of nylon
sleeve
Resilient, lightweight, abrasion and corrosion resistant nylon sleeve accurately molded to mesh
with hubs elliminating friction and need of lubrication
Center groove in sleeves readily permits their use in vertical applications and for blind assembly
Securely held hubs and sleeves by spring-steel retaing rings yet capable of easy removal and still
withstand a 5,000 lbs end thrust
Minimum backlash operating in an ambient temperture environment of -40 to 150 F
Nyflex and Mite Type Performance Data

Nyflex
Speed
RPM
100
Nyflex
Mite
Torque
Bore
Torque
Mite
Keyway
Bore
Keyway
HP
in-lb
Nm
HP
in
Nm
in
in
in
in
2.25
1,420
164
0.60
360
40.7
0.375*
No Keyway
0.312**
No Keyway
500
9.50
1,190
135
2.40
307
34.7
0.500
1/8 x 1/16
0.500
1/8 x 1/16
1,000
18.00
1,125
127
4.50
285
32.2
0.625
3/16 x 3/32
0.625
3/16 x 3/32
1,150
20.30
1,110
125
5.10
282
31.9
0.750
3/16 x 3/32
0.750
3/16 x 3/32
3/16 x 3/32
0.875
3/16 x 3/32
1,500
24.00
970
110
6.40
274
30.9
0.875
1,750
25.00
900
102
7.50
270
30.5
0.937
1/4 x 1/8
0.937
1/4 x 1/8
2,000
26.60
840
95
8.40
267
30.2
1.000
1/4 x 1/8
1.000
1/4 x 1/8
2,500
29.80
750
85
11.10
262
29.6
1.125
1/4 x 1/8
1.125
1/4 x 1/8
3,000
32.50
680
77
12.10
256
28.9
1.187
1/4 x 1/8
3,500
35.30
630
76
13.80
254
28.7
1.250
1/4 x 1/8
4,000
37.50
590
67
17.60
251
28.3
1.312
5/16 x 5/32
27.4
1.375
5/16 x 5/32
1.437
3/8 x 3/16
1.500
3/8 x 3/16
1.625
3/8 x 3/16
5,000
42.00
530
60
19.40
243
Notes: N Angular Misalignment: Nyflex 5; Mite 3.

N Clearence fit bores standard through 1.250 inch bores.
N Interference fit bores standard over 1.250 inch bores.
Notes: N * indicates: Rough Stock Bore .375 .390 inches.

N ** indicates: Rough Stock Bore .312 .327 inches.
G-28
142
630-852-0500
Gear
Nyflex and Mite Type

Dimensional Data
Lovejoy / Sier-Bath Nylon Sleeve Gear Couplings
Nyflex and Mite Type Couplings
Nyflex and Mite Type Dimensional Data

ID1 - ID2
OAL
LS
LTB
BSE
OD
HD
Max Bore
Weight
Size
in
in
in
in
in
in
in
lbs
Nyflex
1.625
3.38
1.88
1.63
0.13
3.75
2.38
3.50
Mite
1.125
2.38
1.31
1.13
0.13
2.88
1.75
1.00
Notes: N Clearence fit bores with set screw over keyway is standard through 1.250 inch bores.
N Interference fit bores with no set screw is standard for bores over 1.250 inch.
N Bore and keyway tolerances conform to ANSI / AGMA 9002-B04.
www.lovejoy-inc.com
143
G-29
Gear
Dentex (Nylon Sleeve Series)

Performance Data
Dentex Nylon Sleeve Series Flexible Couplings
The series is a standard coupling with two hubs, a nylon sleeve, and retaining rings depending on the model
selected. The coupling has a precision molded nylon sleeve and powder metal hub with no bolts, pins,
flanges, or protrusions that could have an effect on balance or operational safety. Since no lubrication is
used, the couplings can readily be adapted to many applications including vertical and blind installations.
Features
Compact in size
Maintenance Free No Lubrication required
Can accommodate axial, angular, and parallel misalignment
Easy to assemble
Electrically insulating
Can be used in temperature ranges from -25 to 80 C (optional 140 C)
Nylon sleeve has high resistance to condensation and water, hydrocarbon based petroleums, and alcohols
Not ideal for use with acids, benzyl based products, cresol, or glycols
Dentex B - Series Performance Data

Size
B 14
B 19
B 24
B 28
B 32
B 38
B 42
B 48
B 55
B 65
B 80
B 100
Torque Capacity
Nominal
Maximum
in-lbs
Nm
in-lbs
Nm
89
10
177
20
142
16
283
32
177
20
354
40
398
45
797
90
531
60
1,062
120
708
80
1,416
160
885
100
1,770
200
1,239
140
2,478
280
2,213
250
4,425
500
3,452
390
6,903
780
6,195
700
12,390
1 400
11,063
1 250
22,125
2 500
Max
Speed
RPM
8,000
8,000
8,000
8,000
7,000
6,000
5,400
5,000
4,000
3,800
3,000
2,400
Misalignment
Axial
in
mm
Angular
Degrees
1
Per
Hub
+/-.039
+/-1
Weight1
Parallel
in
mm
0.012
0.3
0.012
0.3
0.016
0.4
0.016
0.4
0.016
0.4
0.016
0.4
0.016
0.4
0.016
0.4
0.016
0.4
0.024
0.6
0.028
0.7
0.031
0.8
kg
0.2
0.3
0.3
0.7
1.0
1.2
1.5
1.8
3.5
5.2
11.5
20.5
lbs
0.4
0.7
0.7
1.6
2.1
2.7
3.3
4.0
7.6
11.4
25.3
45.2
ID1 - ID22
Min Bore
Max Bore
in
mm
in
mm
0.25
6
0.56
14
0.38
9
0.75
19
0.44
10
0.94
24
0.44
10
1.13
28
0.50
12
1.25
32
0.56
14
1.38
38
0.81
20
1.56
42
0.81
20
1.75
48
1.00
25
2.06
55
1.25
32
2.38
65
1.19
30
3.00
80
1.62
40
3.75
100
Notes: N 1 indicates: Weight is calculated using maximum bore and no keyway.

N 2 indicates: Minimum and maximum bore sizes are given for straight bores. For Taper bores and splines, contact Lovejoy Technical Support.
Dentex B4R - Series Performance Data

Size
B4R 32
B4R 45
B4R 65
B4R 80
B4R 100
Torque Capacity
Nominal
Maximum
in-lbs
Nm
in-lbs
Nm
708
80
1,416
160
1,239
140
2,478
280
3,452
390
6,903
780
6,195
700
12,390
1 400
11,063
1 250
22,125
2 400
Max
Speed
RPM
7,000
5,000
3,800
3,000
2,400
Angular
Degrees
1
Per
Hub
Misalignment
Axial
in
mm
+/-.039
+/-1
Weight 1
Parallel
in
mm
0.016
0.4
0.016
0.4
0.024
0.6
0.028
0.7
0.031
0.8
kg
1.1
1.5
5.4
11.7
20.8
lbs
2.4
3.3
11.9
25.8
45.9
ID1 - ID2 2
Min Bore
Max Bore
in
mm
in
mm
0.50
12
1.25
32
0.81
20
1.56
42
1.00
25
2.38
65
1.19
30
3.00
80
1.62
40
3.75
100

Dentex B3R - Series Performance Data

Size
B3R 24
B3R 28
B3R 32
B3R 45
B3R 65
B3R 80
B3R 100
Torque Capacity
Nominal
Maximum
in-lbs
Nm
in-lbs
Nm
177
20
354
40
398
45
797
90
708
80
1,416
160
1,239
140
2,478
280
3,452
390
6,903
780
6,195
700
12,390
1 400
11,063 1 250
22,125
2 400
Max
Speed
RPM
10,200
8,300
7,000
5,000
3,800
3,000
2,400
Angular
Degrees
1
Per
Hub
Misalignment
Axial
in
mm
+/-.039
+/-1
Weight 1
Parallel
in
mm
0.016
0.4
0.016
0.4
0.016
0.4
0.016
0.4
0.024
0.6
0.028
0.7
0.031
0.8
kg
0.3
0.8
1.1
1.5
5.4
11.6
20.7
lbs
0.7
1.8
2.4
3.3
11.9
25.6
45.6
ID1 - ID2 2
Min Bore
Max Bore
in
mm
in
mm
0.44
10
0.94
24
0.44
10
1.13
28
0.50
12
1.25
32
0.81
20
1.56
42
1.25
32
2.38
65
1.19
30
3.00
80
1.62
40
3.75
100

G-30
144
630-852-0500
Gear
Dentex (Nylon Sleeve Series)

Dimensional Data
B4R
B3R
Dentex B - Series Dimensional Data

OAL
in mm
1.97 50
2.13 54
2.20 56
3.31 84
3.31 84
3.31 84
3.46 88
4.09 104
4.88 124
5.67 144
7.32 186
8.98 228
in
1.46
1.46
1.61
1.81
1.89
1.89
1.97
1.97
2.56
2.83
3.66
4.02
HTS
mm
37
37
41
46
48
48
50
50
65
72
93
102
in
0.26
0.28
0.30
0.75
0.71
0.71
0.75
1.06
1.16
1.42
1.83
2.48
LTB
mm
6.5
7.0
7.5
19.0
18.0
18.0
19.0
27.0
29.5
36.0
46.5
63.0
in
0.91
0.98
1.02
1.57
1.57
1.57
1.65
1.97
2.36
2.76
3.54
4.33
BSE
mm
23
25
26
40
40
40
42
50
60
70
90
110
in
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.24
0.31
OD
mm
4
4
4
4
4
4
4
4
4
4
6
8
HD
in
1.57
1.89
2.05
2.60
2.99
3.27
3.62
3.94
4.92
5.51
6.89
8.27
mm
40
48
52
66
76
83
92
100
125
140
175
210
in
0.98
1.18
1.42
1.73
1.97
2.28
2.56
2.68
3.27
3.78
4.88
5.98
mm
25
30
36
44
50
58
65
68
83
96
124
152
R
(Clearance)
in
mm
0.65 16.5
0.71 18.0
0.73 18.5
0.83 21.0
0.87 22.0
0.87 22.0
0.91 23.0
0.91 23.0
1.20 30.5
1.34 34.0
1.71 43.5
1.85 47.0
T - Metric
Set Screw
Size SL (mm)
M5
6
M5
6
M5
6
M8
10
M8
10
M8
10
M8
10
M8
10
M10
20
M10
20
M10
20
M12
30
T - Inch
Set Screw
Size
SL (in)
10-24
0.24
10-24
0.24
10-24
0.24
5/16-18
0.39
5/16-18
0.39
5/16-18
0.39
5/16-18
0.39
5/16-18
0.39
3/8-16
0.79
3/8-16
0.79
3/8-16
0.79
3/8-16
1.18
mm
50
65
96
124
152
R
(Clearance)
in
mm
1.06 27.0
1.10 28.0
1.57 40.0
1.71 43.5
1.85 47.0
T - Metric
Set Screw
Size SL (mm)
M8
10
M8
10
M10
20
M10
20
M12
30
T - Inch
Set Screw
Size
SL (in)
5/16-18
0.39
5/16-18
0.39
3/8-16
0.79
3/8-16
0.79
3/8-16
0.79
mm
36
44
50
65
96
124
152
R
(Clearance)
in
mm
0.93 23.5
1.02 26.0
1.06 27.0
1.10 28.0
1.57 40.0
1.71 43.5
1.85 47.0
T - Metric
Set Screw
Size SL (mm)
M5
6
M8
10
M8
10
M8
10
M10
20
M10
20
M12
30
T - Inch
Set Screw
Size
SL (in)
10-24
0.24
3/8-16
0.39
3/8-16
0.39
3/8-16
0.39
3/8-16
0.39
3/8-16
0.39
3/8-16
0.39
Dentex B4R - Series Dimensional Data

OAL
Size
B4R 32
B4R 45
B4R 65
B4R 80
B4R 100
in
3.31
3.46
5.67
7.32
8.98
LS
mm
84
88
144
186
228
in
2.28
2.36
3.31
3.66
4.02
HTS
mm
58
60
84
93
102
in
0.51
0.55
1.18
1.83
2.48
LTB
mm
13.0
14.0
30.0
46.5
63.0
in
1.57
1.65
2.76
3.54
4.33
BSE
mm
40
42
70
90
110
in
0.16
0.16
0.16
0.24
0.31
OD
mm
4
4
4
6
8
in
3.31
3.94
5.51
6.89
8.27
HD
mm
84
100
140
175
210
in
1.97
2.56
3.78
4.88
5.98
Dentex B3R - Series Dimensional Data

OAL
Size
B3R 24
B3R 28
B3R 32
B3R 45
B3R 65
B3R 80
B3R 100
in
2.20
3.31
3.31
3.46
5.67
7.32
8.98
mm
56
84
84
88
144
186
228
LS
in
2.01
2.20
2.28
2.36
3.31
3.66
4.02
HTS
mm
51
56
58
60
84
93
102
in
0.10
0.55
0.51
0.55
1.18
1.83
2.48
mm
2.5
14.0
13.0
14.0
30.0
46.5
63.0
LTB
in
1.02
1.57
1.57
1.65
2.76
3.54
4.33
mm
26
40
40
42
70
90
110
BSE
in
0.16
0.16
0.16
0.16
0.16
0.24
0.31
OD
mm
4
4
4
4
4
6
8
in
2.28
2.76
3.31
3.94
5.51
6.89
8.27
mm
58
70
84
100
140
175
210
HD
in
1.42
1.73
1.97
2.56
3.78
4.88
5.98
Notes: N Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04.
N Metric bores and keyway tolerances conform to ISO 286 and ANSI / AGMA 9112-A04.
www.lovejoy-inc.com
145
G-31
Size
B 14
B 19
B 24
B 28
B 32
B 38
B 42
B 48
B 55
B 65
B 80
B 100
LS
Gear
C Universal Hub
Dimensional Data
C Type Universal Hub
C Standard and Universal Hub Dimensions

L1
Size
G-32
L2
L3
TW
LTB
LTB1
STD HUB
UNIV HUB
in
in
in
in
in
in
7/8
3.38
1.13
0.13
0.25
1.50
3.75
1.5
3.36
1.17
0.13
0.52
1.81
4.00
4.06
1.50
0.13
0.44
2.06
4.63
2.5
4.39
1.52
0.16
0.58
2.25
5.13
4.89
1.77
0.25
0.61
2.63
5.75
3.5
5.58
3.33
0.25
0.67
4.25
6.50
5.52
3.27
0.25
0.86
4.38
6.63
4.5
6.64
3.89
0.25
0.86
5.00
7.75
6.39
4.52
0.25
1.23
6.00
7.88
7.64
4.52
0.25
1.61
6.38
9.50
146
630-852-0500
Gear
Flanged Sleeve
Cut Away
Lovejoy / Sier-Bath Flanged Sleeve Gear Couplings
Draw-off Holes (Optional)

Gasket
Vari-Crown Hub Teeth
Both Hub Diameters are Identical
Larger Bore
Capacity
O Ring Seals
Interference Fit
Major Diameter Fit
One Piece Sleeve
Heat-Treated Bolts
for High Strength Coated for
Corrosion Resistance
Flanges Available in
Both Shrouded and Exposed
Bolt Design
www.lovejoy-inc.com
Two Lubrication Plugs

in Each Half Sleeve
147
G-33
Med. Carbon Steel

Hubs & Sleeves
Gear
F Type
Performance Data
F Type Flex-Flex Couplings
The F Type coupling consists of two flex hubs, two sleeves and one accessory
kit. This coupling is supplied with exposed bolts as standard. Shrouded bolts are
available upon request through size 5.5.
Features
Patented Vari-Crown tooth form for long life
Standard 20 pressure angle
Heat treated bolts for greater strength
Corrosion resistant bolts and nuts for ease of maintenance
Provides parallel, angular misalignment and end float
Flex Half coupling interchangeable with industry standards
F Type Performance Data

ID1 - ID2
Nominal
Maximum
Torque
in-lb
Rough Stock
Speed
Unbal
Size
Max Bore
Bore
Axial
Max Angular
Misalignment
Misalignment
Bal
Degrees
RPM
RPM
in
in
mm
in
mm
7,600
850
6,000
9,000
1.625
42
0.44
11
0.056
1.4
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
19
0.060
1.5
31,500
3 560
5,000
7,500
2.750
73
0.94
24
34
15
0.085
2.2
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
37
54
25
0.105
2.7
Nm
Weight
mm
lbs
kg
94,500
10 700
4,000
6,000
4.000
107
1.44
37
80
36
0.115
2.9
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
130
59
0.130
3.3
1.5
Per Gear Mesh
220,500
24 900
3,000
4,500
5.375
145
2.44
62
190
86
0.150
3.8
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
250
114
0.175
4.4
434,700
49 100
2,500
3,750
6.500
180
3.00
76
380
173
0.200
5.1
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
520
236
0.220
5.6
749,700
84 700
2,100
3,150
8.250
225
4.00
101
650
295
0.120
3.0
1,008,000
113 900
2,000
3,000
9.500
255
5.00
127
950
431
0.135
3.4
1,323,000
149 500
1,900
2,850
11.500
310
6.00
152
1,560
708
0.160
4.1
1,827,000
206 400
1,800
2,700
12.500
340
6.00
177
2,015
915
0.165
4.2
Shaft sizes.
G-34
148
630-852-0500
Gear
F Type
Dimensional Data
F Type Flex-Flex Couplings
Shrouded bolt design

also available
F Type Dimensional Data

OAL
ID1 - ID2
Max Bore
LTB
BSE
AD
FD
HD
in
in
in
in
in
in
Rough Stock
Bore
Size
in
in
3.50
1.625
42
0.44
11
1.69
0.13
2.04
4.56
3.06
2.31
1.5
4.00
2.125
56
0.69
18
1.94
0.13
2.32
6.00
3.97
3.00
5.00
2.750
73
0.94
24
2.44
0.13
2.94
7.00
4.86
4.00
2.5
6.25
3.250
85
1.44
37
3.03
0.19
3.47
8.38
5.84
4.63
7.38
4.000
107
1.44
37
3.59
0.19
3.97
9.44
6.84
5.63
3.5
8.63
4.625
125
1.81
46
4.19
0.25
4.57
11.00
7.91
6.50
9.75
5.375
145
2.44
62
4.75
0.25
5.00
12.50
9.25
7.50
4.5
10.94
6.000
165
3.00
76
5.31
0.31
5.50
13.63
10.38
8.50
12.38
6.500
180
3.00
76
6.03
0.31
6.34
15.31
11.56
9.50
5.5
14.13
7.500
200
4.00
101
6.91
0.31
7.04
16.75
12.72
10.50
15.13
8.250
225
4.00
101
7.41
0.31
8.35
18.00
14.00
11.50
17.75
9.500
255
5.00
127
8.69
0.38
9.82
20.75
15.75
13.00
22.38
11.500
310
6.00
152
11.00
0.38
12.31
23.25
18.34
15.50
23.50
12.500
340
6.00
177
11.50
0.50
13.00
26.00
20.38
17.00
Notes: N
N
N
N
N
N
N
mm
in
mm
Exposed Bolt Design is standard.

Shrouded Bolt Design available upon request for sizes 1 through 5.5.
Puller Holes are available for sizes 1 through 3.5 at an additional charge.
Bore and keyway tolerances conform to ANSI / AGMA 9002-B04.
www.lovejoy-inc.com
149
G-35
Gear
FFR Type
Performance Data
FFR Single Engagement (Flex-Rigid)
The FRR Type coupling consists of one flex hub, one rigid hub, one sleeve and
one accessory kit. This coupling is supplied with exposed bolts as standard.
Shrouded bolts are available upon request through size 5.5.
Features
Patented Vari-Crown tooth form on the Flex Hub for long life
Accommodates angular misalignment only
Half coupling interchangeable with industry standards
FFR Type Performance Data

ID1
Size
Nominal
Maximum
Flex Hubs
Flex Hubs
Rigid Hubs
Rigid Hubs
Torque
Speed
Max Bore
Rough Stock
Max Bore
Rough Stock
in
in
mm
in-lb
ID2
Nm
Unbal
Bal
RPM
RPM
in
Bore
mm
in
Weight
Max Angular
Misalignment
Bore
mm
mm
lbs
kg
7,600
850
6,000
9,000
1.625
42
0.44
11
2.125
56
solid
solid
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
2.813
76
solid
solid
17
31,500
3 560
5,000
7,500
2.750
73
0.94
24
3.500
95
solid
solid
34
15
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
37
4.250
114
solid
solid
55
25
94,500
10 700
4,000
6,000
4.000
107
1.44
37
4.875
134
solid
solid
86
39
Degrees
1.5
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
5.625
150
solid
solid
125
61
Per
220,500
24 900
3,000
4,500
5.375
145
2.44
62
6.500
176
solid
solid
195
89
Gear
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
7.625
202
solid
solid
268
122
Mesh
434,700
49 100
2,500
3,750
6.500
180
3.00
76
8.750
230
4.00
101
394
179
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
9.500
260
4.50
114
526
239
749,700
84 700
2,100
3,150
8.250
225
4.00
101
10.500
285
5.50
127
687
312
1,008,000
113 900
2,000
3,000
9.500
255
5.00
127
12.000
320
5.75
139
1,017
462
1,323,000
149 500
1,900
2,850
11.500
310
6.00
152
14.000
375
6.50
165
1,609
730
1,827,000
206 400
1,800
2,700
12.500
340
7.00
177
15.500
415
7.50
190
2,128
966
Shaft sizes.
G-36
150
630-852-0500
Gear
FFR Type
Dimensional Data
FFR Type Flex-Rigid Couplings
FFR Type Dimensional Data

OAL
ID1
ID2
LTB
Flex Hubs
Flex Hubs
Rigid Hubs
Rigid Hubs
Max Bore
Rough Stock
Max Bore
Rough Stock
Bore
Size
in
in
3.41
1.625
mm
42
LTB 1
BSE
AD
FD
HD
Bore
in
mm
in
mm
in
mm
in
in
in
in
in
in
in
0.44
11
2.125
56
solid
solid
1.69
1.56
0.16
2.19
4.56
3.06
2.31
1.5
3.94
2.125
56
0.69
18
2.813
76
solid
solid
1.94
1.84
0.16
2.47
6.00
3.97
3.00
4.88
2.750
73
0.94
24
3.500
95
solid
solid
2.44
2.28
0.16
3.10
7.00
4.86
4.00
2.5
6.13
3.250
85
1.44
37
4.250
114
solid
solid
3.03
2.91
0.19
3.65
8.38
5.84
4.63
7.19
4.000
107
1.44
37
4.875
134
solid
solid
3.59
3.41
0.19
4.15
9.44
6.84
5.63
3.5
8.38
4.625
125
1.81
46
5.625
150
solid
solid
4.19
3.97
0.22
4.78
11.00
7.91
6.50
4
4.5
9.50
5.375
145
2.44
62
6.500
176
solid
solid
4.75
4.44
0.31
5.31
12.50
9.25
7.50
10.69
6.000
165
3.00
76
7.625
202
solid
solid
5.31
5.03
0.34
5.97
13.63
10.38
8.50
12.06
6.500
180
3.00
76
8.750
230
4.00
101
6.03
5.69
0.34
6.69
15.31
11.56
9.50
5.5
13.41
7.500
200
4.00
101
9.500
260
4.50
114
6.91
6.16
0.34
7.34
16.75
12.72
10.50
15.22
8.250
225
4.00
101
10.500
285
5.50
127
7.41
7.41
0.41
8.78
18.00
14.00
11.50
17.88
9.500
255
5.00
127
12.000
322
5.75
139
8.69
8.69
0.50
10.31
20.75
15.75
13.00
22.50
11.500
310
6.00
152
14.000
375
6.50
165
11.00
11.00
0.50
12.81
23.25
18.34
15.50
23.56
12.500
340
7.00
177
15.500
415
7.50
190
11.50
11.50
0.56
13.56
26.00
20.38
17.00
Notes: N
N
N
N
N
N
N

www.lovejoy-inc.com
151
G-37
Gear
FFS Type
Performance Data
FFS Floating Shaft Gear Coupling
The FFS Type coupling consists of two flex-rigid couplings and one floating
shaft. This coupling is supplied with rigid hubs outboard unless otherwise
specified. Exposed bolts are standard. Shrouded bolts are available upon
request tru sizes 5.5.
Features
Patented Vari-Crown tooth form on Flex Hubs for long life
Accommodates angular, parallel, and axial misalignment
Removal of center assembly allows for ease of maintenance without
repositioning machinery
Rigid hubs outboard allows for larger shaft diameters
FFS Type Performance Data

Nominal
Maximum
1
Torque
Size
1
in-lb
Speed
Nm
ID1 - ID2
ID1 - ID2
ID1 - ID2
ID1 - ID2
Rigid Hubs
Rigid Hubs
Flex Hubs
Flex Hubs
Max Bore
Rough Stock
Max Bore
Rough Stock
Unbal
Bal
Bore
RPM
RPM
in
mm
in
Weight
Angular
Misalignment
Bore
mm
in
mm
in
Max
mm
lbs
kg
Degrees
7,600
850
6,000
9,000
2.125
56
1.625
42
0.44
11
1.5
18,900
2 140
5,500
8,250
2.813
76
2.125
56
0.69
18
19
31,500
3 560
5,000
7,500
3.500
95
2.750
73
0.94
24
34
15
2.5
56,700
6 410
4,400
6,600
4.250
114
3.250
85
1.44
37
54
25
94,500
10 700
4,000
6,000
4.875
134
4.000
107
1.44
37
80
36
3.5
151,200
17 100
3,500
5,250
5.625
150
4.625
125
1.81
46
130
59
220,500
24 900
3,000
4,500
6.500
176
5.375
145
2.44
62
190
86
Per
4.5
302,400
34 200
2,700
4,050
7.625
202
6.000
165
3.00
76
250
114
Gear
434,700
49 100
2,500
3,750
8.750
231
4.000
101
6.500
180
3.00
76
380
173
Mesh
5.5
573,300
64 800
2,200
3,300
9.500
260
4.500
114
7.500
200
4.00
101
520
236
Solid
w/Center
749,700
84 700
2,100
3,150
10.500
288
5.500
127
8.250
225
4.00
101
650
295
1,008,000
113 900
2,000
3,000
12.000
318
5.750
139
9.500
255
5.00
127
950
431
1,323,000
149 500
1,900
2,850
14.000
380
6.500
165
11.500
310
6.00
152
1,560
708
1,827,000
206 400
1,800
2,700
15.500
418
7.500
190
12.500
340
6.00
177
2,015
915
Note:
1.5
N 1 indicates: Maximum RPM of floating shaft set determined by critical speed of floating shaft.
Equipment shaft sizes.
Specify which hubs are to be used on the equipment (Rigid or Flex).
Rigid hubs will be used on the equipment unless otherwise specified.
G-38
152
630-852-0500
Gear
FFS Type
Dimensional Data
Lovejoy / Sier-Bath Flanged Gear Couplings
FFS Type Floating Shaft Couplings
Rigid Hubs Outboard
Flex Hubs Outboard

Maximum RPM of floating shaft set determined by
critical speed of floating shaft
FFS Type Dimensional Data

OAL
BSE
Min
Min
ID1 - ID2
ID1 - ID2
LTB 1
Rigid Hubs
Rigid Hubs
Flex Hubs
Flex Hubs
Max Bore
Rough Stock
Max Bore
Rough Stock
Bore
Size
in
in
in
8.07
4.94
2.125
1.5
mm
in
LTB
AD
FD
D1
HD
Bore
mm
56
in
mm
in
1.625
42
0.44
mm
11
in
in
in
in
in
in
in
in
1.56
1.69
0.16
2.06
4.56
3.06
3.06
2.31
9.19
5.50
2.813
76
2.125
56
0.69
18
1.84
1.94
0.16
2.37
6.00
3.97
3.97
3.00
12.06
7.50
3.500
95
2.750
73
0.94
24
2.28
2.44
0.16
2.94
7.00
4.84
4.91
4.00
2.5
14.37
8.56
4.250
114
3.250
85
1.44
37
2.91
3.03
0.19
3.53
8.38
5.84
5.91
4.63
16.69
9.88
4.875
134
3.5
19.25
11.31
5.625
150
Solid
w/Center
4.000
107
1.44
37
3.41
3.59
0.19
3.97
9.44
6.84
6.91
5.63
4.625
125
1.81
46
3.97
4.19
0.22
4.56
11.00
7.91
7.91
6.50
21.82
12.94
6.500
176
5.375
145
2.44
62
4.44
4.75
0.31
5.00
12.50
9.25
9.25
7.50
4.5
24.69
14.63
7.625
202
6.000
165
3.00
76
5.03
5.31
0.34
5.69
13.63
10.38
10.38
8.50
28.07
16.69
8.750
231
4.000
101
6.500
180
3.00
76
5.69
6.03
0.34
6.35
15.31
11.56
11.56
9.50
5.5
30.87
18.56
9.500
260
4.500
114
7.500
200
4.00
101
6.16
6.91
0.34
6.59
16.75
12.72
12.81
10.50
35.37
20.56
10.500
288
5.500
127
8.250
225
4.00
101
7.41
7.41
0.41
8.78
18.00
14.00
14.00
11.50
40.63
23.25
12.000
318
5.750
139
9.500
255
5.00
127
8.69
8.69
0.50
10.31
20.75
15.75
15.75
13.00
49.63
27.63
14.000
380
6.500
165
11.500
310
6.00
152
11.00
11.00
0.50
12.81
23.25
18.34
18.50
15.50
52.13
29.13
15.500
418
7.500
190
12.500
340
6.00
177
11.50
11.50
0.56
13.56
26.00
20.38
20.38
17.00
Notes: N
N
N
N
N
N
N

www.lovejoy-inc.com
153
G-39
Gear
FHD Type
Performance Data
Lovejoy / Sier-Bath Heavy Duty Flanged Sleeve Gear Couplings
FHD Type Flex-Flex Couplings
The FHD Type coupling consists of two flex hubs, two sleeves with bolt-on steel carriers and
one accessory kit. This coupling is supplied with exposed bolts only.
Features
Designed for high-torque low-speed applications that occur in mill operations
FHD Type Performance Data

ID1 - ID2
Nominal
Torque
Size
in-lb
Nm
Maximum
Max Bore
Speed
Standard
Unbal
Bal
RPM
RPM
Weight
Parallel
Angular
Misalignment
Misalignment
Keyway
in
Degrees
mm
lbs
kg
in
mm
1,008,000
110 000
2,000
3,000
9.500
255
950
431
0.135
3.429
1 235000
150 000
1,900
2,850
11.500
310
1,560
708
0.160
4.064
1,827,700
210 000
1,750
2,625
12.500
340
2,015
915
0.165
4.191
10
2,521,000
280 000
1,550
2,325
13.750
355
2,500
1,135
0.180
4.572
11
3,466,000
390 000
1,400
2,100
15.500
410
3,380
1,535
0.205
5.207
12
4,412,000
500 000
1,300
1,950
17.000
435
4,165
1,891
0.210
5.334
13
5,249,000
600 000
1,150
1,725
18.250
480
5,215
2,368
0.230
5.842
14
6,429,000
730 000
1,050
1,575
19.500
6,400
2,906
0.255
6.477
15
7,752,000
880 000
900
1,350
21.000
7,710
3,500
0.280
7.112
16
9,454,000
1 070 000
800
1,200
22.500
9,250
4,200
0.295
7.493
18
12,605,000
1 420 000
550
825
25.500
11,890
5,398
0.295
7.493
20
17,017,000
1 920 000
450
675
28.000
16,830
7,641
0.280
7.112
22
21,429,000
2 420 000
380
570
31.000
21,970
9,974
0.310
7.874
24
26,471,000
2 990 000
325
485
34.000
27,735
12,592
0.300
7.620
26
32,773,000
3 700 000
280
420
37.000
34,370
15,604
0.300
7.620
28
39,076,000
4 410 000
240
360
40.000
40,910
18,573
0.320
8.128
30
47,269,000
5 340 000
220
330
42.000
47,470
21,551
0.320
8.128
0.75
Per Gear Mesh
Shaft sizes.
G-40
154
630-852-0500
Gear
FHD Type
Dimensional Data
FHD Type Flex-Flex Couplings
FHD Type Dimensional Data

OAL
ID1 - ID2
Max Bore
1 Rectangular
Standard
Keyway
Keyway
LTB
BSE
FD
HD
in
in
in
in
in
0.38
20.75
15.75
13.00
Width
Depth
in
in
mm
in
in
17.25
9.500
255
2.5000
0.8750
22.38
11.500
310
3.0000
1.0000
11.00
0.38
23.25
18.34
15.50
23.50
12.500
340
3.0000
1.0000
11.50
0.50
26.00
20.38
17.00
10
24.50
13.750
355
3.5000
1.2500
12.00
0.50
28.00
22.31
18.50
11
26.75
15.500
410
4.0000
1.5000
13.13
0.50
30.50
24.36
21.00
12
28.25
17.000
435
4.0000
1.5000
13.88
0.50
33.00
26.63
22.75
13
30.00
18.250
480
5.0000
1.7500
14.63
0.75
33.75
28.88
24.75
14
31.75
19.500
5.0000
1.7500
15.50
0.75
38.00
31.00
26.50
15
33.75
21.000
5.0000
1.7500
16.50
0.75
40.50
32.97
28.50
16
35.75
22.500
6.0000
2.0000
17.38
1.00
43.00
35.13
30.38
18
37.00
25.500
6.0000
2.0000
18.00
1.00
47.25
39.25
34.25
20
43.25
28.000
7.0000
2.5000
21.13
1.00
53.50
43.50
38.00
22
47.00
31.000
8.0000
2.7500
23.00
1.00
59.00
47.63
41.81
24
50.50
34.000
9.0000
3.0000
24.75
1.00
64.25
51.75
45.50
26
54.00
37.000
9.0000
3.0000
26.50
1.00
68.50
55.88
49.38
28
55.25
40.000
10.0000
3.5000
27.13
1.00
73.75
60.00
53.00
30
56.25
42.000
10.0000
3.5000
27.63
1.00
78.00
64.13
57.00
Size
Notes: N
N
N
N
N
8.69

Puller Holes are standard.
Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04, for bores above 18 inches, keyways conform to ANSI B17.1.
For metric bore and keyway tolerances, consult Lovejoy Engineering Section.
www.lovejoy-inc.com
155
G-41
Gear
FHDFR Type
Performance Data
FHDFR Type Flex-Rigid Couplings
The FHDFR Type coupling consists of one flex hub, one sleeve
with bolt-on seal carrier, one rigid hub and one accessory kit. This
coupling is supplied with exposed bolts only.
Features
Designed for high-torque low-speed applications that occur in

mill operations
FHDFR Type Performance Data

Nominal
Maximum
Torque
in-lb
Size
Speed
Nm
x 1000
Unbal
Bal
ID1
ID2
Flex Hubs
Rigid Hubs
Weight
Max
Max Bore
Max Bore
Angular
Std Keyway
Std Keyway
Misalignment
RPM
RPM
1,008
110
2,000
3,000
in
mm
in
mm
lbs
9.500
255
12.000
320
1,017
kg
1,324
150
1,900
2,850
11.500
310
14.000
375
1,609
730
1,827
210
1,750
2,625
12.500
340
15.500
415
2,128
966
10
2,521
280
1,550
2,325
13.750
355
17.000
455
2,723
1,236
Degrees
462
11
3,466
390
1,400
2,100
15.500
410
18.500
500
3,640
1,653
12
4,412
500
1,300
1,950
17.000
435
20.250
4,508
2,047
13
5,249
600
1,150
1,725
18.250
480
22.000
5,600
2,542
14
6,429
730
1,050
1,575
19.500
23.500
6,837
3,104
15
7,752
880
900
1,350
21.000
24.250
8,244
3,743
16
9,454
1 070
800
1,200
22.500
26.000
9,848
4,471
18
12,605
1 420
550
825
25.500
28.000
12,673
5,754
20
17,017
1 920
450
675
28.000
31.000
18,113
8,223
22
21,429
2 420
380
570
31.000
34.000
23,671
10,747
24
26,471
2 990
325
485
34.000
37.000
29,958
13,601
26
32,773
3 700
280
420
37.000
40.000
37,014
16,845
28
39,076
4 410
240
360
40.000
43.000
44,012
19,981
30
47,269
5 340
220
330
42.000
46.000
51,065
23,184
0.75
Per
Gear
Mesh
Shaft sizes.
G-42
156
630-852-0500
Gear
FHDFR Type
Dimensional Data
FHDFR Type Flex-Rigid Couplings
OAL
Size
in
FHDFR Type Dimensional Data

ID1
ID2
Flex Hubs
Rigid Hubs
Max Bore
Max Bore
Std Keyway
Std Keyway
in
mm
in
mm
LTB
LTB1
BSE
FD
HD
in
in
in
in
in
in
17.81
9.500
255
12.000
320
8.69
8.69
0.50
20.75
15.75
13.00
22.50
11.500
310
14.000
375
11.00
11.00
0.50
23.25
18.34
15.50
23.56
12.500
340
15.500
415
11.50
11.50
0.56
26.00
20.38
17.00
10
24.63
13.750
355
17.000
455
12.00
12.00
0.63
28.00
22.31
18.50
11
26.88
15.500
410
18.500
500
13.13
13.13
0.63
30.50
24.36
21.00
12
28.38
17.000
435
20.250
13.88
13.88
0.63
33.00
26.63
22.75
13
30.00
18.250
480
22.000
14.63
14.63
0.75
33.75
28.88
24.75
14
31.75
19.500
23.500
15.50
15.50
0.75
38.00
31.00
26.50
15
33.75
21.000
24.250
16.50
16.50
0.75
40.50
32.97
28.50
16
35.75
22.500
26.000
17.38
17.38
1.00
43.00
35.13
30.38
18
37.00
25.500
28.000
18.00
18.00
1.00
47.25
39.25
34.25
20
43.25
28.000
31.000
21.13
21.13
1.00
53.50
43.50
38.00
22
47.13
31.000
34.000
23.00
23.00
1.13
59.00
47.63
41.81
24
50.63
34.000
37.000
24.75
24.75
1.13
64.25
51.75
45.50
26
54.13
37.000
40.000
26.50
26.50
1.13
68.50
55.88
49.38
28
55.38
40.000
43.000
27.13
27.13
1.13
73.75
60.00
53.00
30
56.38
42.000
46.000
27.63
27.63
1.13
78.00
64.13
57.00
Notes: N
N
N
N

Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04, for bores above 18 inches, keyways
are to ANSI B17.1.
N Metric bore and keyway tolerances conform to ISO 286 and ANSI / AGMA 9112-A04.
N Consult Lovejoy Technical Support for metric bores larger than 500mm.
www.lovejoy-inc.com
157
G-43
Gear
FHDFS Type
Performance Data
FHDFS Type Floating Shaft Couplings
The FHDFS Type coupling consists of two flex-rigid couplings and one floating shaft. The coupling is supplied
with the rigid hubs outboard unless otherwise specified. The coupling comes with exposed bolts only.
Features
Patented Vari-Crown tooth form on Flex Hubs for long life
Accommodates parallel and angular misalignment
Removal of center assembly allows forease of maintenance without repositioning machinery
Rigid hubs outboard allows for larger shaft diameters
Designed for high-torque low-speed applications that occur in mill operations
FHDFS Type Performance Data

Nominal
Maximum
ID2
Rigid Hubs
Max Bore
Max Bore
Torque
Size
ID1
Flex Hubs
Speed
in-lb
Nm
Weight
Max Angular
Misalignment
Unbal
Bal
Std Keyway
Std Keyway
RPM
RPM
in
mm
in
mm
lbs
Degrees
kg
1,008,000
113 900
2,000
3,000
9.500
255
12.000
320
1,017
462
1,323,000
149 000
1,900
2,850
11.500
310
14.000
375
1,609
730
1,827,000
206 400
1,750
2,625
12.500
340
15.500
415
2,128
966
10
2,500,000
280 000
1,550
2,325
13.750
355
17.000
455
2,723
1,236
11
3,500,000
390 000
1,400
2,100
15.500
410
18.500
500
3,640
1,653
12
4,400,000
500 000
1,300
1,950
17.000
435
20.250
4,508
2,047
0.75
13
5,300,000
600 000
1,150
1,725
18.250
480
22.000
5,600
2,542
Per Gear Mesh
14
6,400,000
730 000
1,050
1,575
19.500
23.500
6,837
3,104
15
7,700,000
880 000
900
1,350
21.000
24.250
8,244
3,743
16
9,500,000
1 070 000
800
1,200
22.500
26.000
9,848
4,471
18
12,600,000
1 420 000
550
825
25.500
28.000
12,673
5,754
20
17,000,000
1 920 000
450
675
28.000
31.000
18,113
8,223
22
21,400,000
2 420 000
380
570
31.000
34.000
23,671
10,747
24
26,500,000
2 990 000
325
488
34.000
37.000
29,958
13,601
26
32,800,000
3 700 000
280
420
37.000
40.000
37,104
16,845
28
39,100,000
4 410 000
240
360
40.000
43.000
44,012
19,981
47,300,000
5 340 000
220
330
42.000
46.000
51,065
23,184
30
Note:
N 1 indicates: Maximum RPM of floating shaft set determined by critical speed of floating shaft.

Connecting equipment shaft sizes.
Specify which hubs are to be used on the equipment (Rigid or Flex).
Rigid hubs will be used on the equipment unless otherwise specified.
Length of floating shaft may affect max angular misalignment.
G-44
158
630-852-0500
Gear
FHDFS Type
Dimensional Data
FHDFS Type Floating Shaft Couplings
Flex Hubs Outboard
Rigid Hubs Outboard
Maximum RPM of floating shaft set determined by

critical speed of floating shaft
FHDFS Type Dimensional Data

OAL
Size
in
BSE
in
ID1
ID2
Flex Hubs
Rigid Hubs
LTB 1
Max Bore
Max Bore
Std Keyway
Std Keyway
LTB
FD
D1
HD
in
mm
in
mm
in
in
in
in
in
in
in
9.500
255
12.000
320
8.69
8.69
0.50
20.75
15.75
15.75
13.00
11.500
310
14.000
375
11.00
11.00
0.50
23.25
18.34
18.50
15.50
To Be Determined
From Customer
12.500
340
15.500
415
11.50
11.50
0.56
26.00
20.38
20.38
17.00
10
Specifications
13.750
355
17.000
455
12.00
12.00
0.63
28.00
22.31
22.38
18.50
11
15.500
410
18.500
500
13.13
13.13
0.63
30.50
24.36
24.50
21.00
12
17.000
435
20.250
13.88
13.88
0.63
33.00
26.63
26.63
22.75
13
18.250
480
22.000
14.63
14.63
0.75
33.75
28.88
28.88
24.75
14
19.500
23.500
15.50
15.50
0.75
38.00
31.00
31.00
26.50
15
21.000
24.250
16.50
16.50
0.75
40.50
32.97
33.13
28.50
16
22.500
26.000
17.38
17.38
1.00
43.00
35.13
35.13
30.38
18
25.500
28.000
18.00
18.00
1.00
47.25
39.25
39.25
34.25
20
28.000
31.000
21.13
21.13
1.00
53.50
43.50
43.50
38.00
22
31.000
34.000
23.00
23.00
1.13
59.00
47.63
47.63
41.81
24
34.000
37.000
24.75
24.75
1.13
64.25
51.75
51.75
45.50
26
37.000
40.000
26.50
26.50
1.13
68.50
55.88
55.88
49.38
28
40.000
43.000
27.13
27.13
1.13
73.75
60.00
60.00
53.00
30
42.000
46.000
27.63
27.63
1.13
78.00
64.13
64.13
57.00
Notes: N
N
N
N
N
N

Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04, for bores about 18 inches, keyways are to ANSI B17.1.
Consult Lovejoy Technical Support for metric bores larger than 500mm.
www.lovejoy-inc.com
159
G-45
Gear
FMM Type
Performance Data
FMM Type Mill Couplings
The FMM Type coupling consists of one standard flex hub, one universal straight
bored hub as standard, two sleeves and one accessory kit. This coupling is
supplied with exposed bolts as standard. Shrouded bolts are available upon
request through size 5.5.
Features
Long Universal Hub supplied to customer specifications with straight or

tapered bores
FMM Type Performance Data

ID1 - ID2
Nominal
Maximum
Torque
Speed
Unbal
Size
in-lb
Rough Stock
Weight
Bore
Parallel
Max Angular
Misalignment
Misalignment
Bal
Degrees
RPM
RPM
in
mm
lbs
7,600
850
6,000
9,000
1.625
42
0.44
11
12
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
31,500
3 560
5,000
7,500
2.750
73
0.94
24
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
94,500
10 700
4,000
6,000
4.000
107
1.44
3.5
151,200
17 100
3,500
5,250
4.625
125
220,500
24 900
3,000
4,500
5.375
4.5
302,400
34 200
2,700
4,050
6.000
434,700
49 100
2,500
3,750
5.5
573,300
64 800
2,200
3,300
749,700
84 700
2,100
3,150
Nm
Max Bore
mm
in
kg
in
mm
0.056
1.4
24
11
0.060
1.5
45
20
0.085
2.2
37
71
32
0.105
2.7
37
104
47
0.115
2.9
1.81
46
151
69
0.130
3.3
145
2.44
62
234
86
0.150
3.8
165
3.00
76
310
141
0.175
4.4
6.500
180
3.00
76
450
204
0.200
5.1
7.500
200
4.00
101
609
276
0.220
5.6
8.250
225
4.00
101
764
347
0.120
3.0
1.5
Per Gear Mesh
Shaft sizes.
Taper per foot and length of taper if tapered bore is required.
Specify counterbore dimensions if desired.
Submit a drawing if available.
G-46
160
630-852-0500
Gear
FMM Type
Dimensional Data
FMM Type Mill Couplings
FMM Type Dimensional Data

OAL
ID1 - ID2
Max Bore
LTB
Rough Stock
LTB1
BSE
FD
HD
Max
Bore
Size
in
5.81
in
1.625
mm
42
in
mm
in
in
in
in
in
in
0.44
11
1.69
4.00
0.13
4.56
3.06
2.31
1.5
6.56
2.125
56
0.69
18
1.94
4.50
0.13
6.00
3.97
3.00
8.06
2.750
73
0.94
24
2.44
5.50
0.13
7.00
4.86
4.00
2.5
9.72
3.250
85
1.44
37
3.03
6.50
0.19
8.38
5.84
4.63
10.78
4.000
107
1.44
37
3.59
7.00
0.19
9.44
6.84
5.63
3.5
11.94
4.625
125
1.81
46
4.19
7.50
0.25
11.00
7.91
6.50
13.25
5.375
145
2.44
62
4.75
8.25
0.25
12.50
9.25
7.50
4.5
14.63
6.000
165
3.00
76
5.31
9.00
0.31
13.63
10.38
8.50
15.84
6.500
180
3.00
76
6.03
9.50
0.31
15.31
11.56
9.50
5.5
17.72
7.500
200
4.00
101
6.91
10.50
0.31
16.75
12.72
10.50
18.97
8.250
225
4.00
101
7.41
11.25
0.31
18.00
14.00
11.50
Notes: N LTB1 Dimensions are the maximum lengths of Universal Hubs kept in stock and altered to customer specifications. Longer length
hubs are made to order.
N Exposed Bolt Design is standard.
N Shrouded Bolt Design available upon request for sizes 1 through 5.5.
N Puller Holes are standard on sizes 4 through 6.
N Puller Holes are available for sizes 1 through 3.5 at an additional charge.
N Interference bores with no set screws are standard unless otherwise specified.
N Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04.
N For metric bore and keyway tolerances, consult Lovejoy Engineering Section.
www.lovejoy-inc.com
161
G-47
Gear
FMM Mill Motor Type
Performance Data
FMM Type Mill Motor Couplings
The FMM Type coupling consists of one standard flex hub, one universal straight bored
hub as standard, two sleeves and one accessory kit. This coupling is supplied with
exposed bolts as standard. Shrouded bolts are available upon request through size 5.5.
Features
Long Universal Hub used for AISE Motor Frames
FMM Type Mill Motor Performance Data

ID1 - ID2
Nominal
Maximum
Torque
Speed
Unbal
Size
in-lb
7,600
Nm
850
Max Bore
Rough Stock
Weight
Bore
Parallel
Max Angular
Misalignment
Misalignment
Bal
Degrees
RPM
RPM
in
6,000
9,000
1.625
mm
42
in
mm
lbs
kg
0.44
11
12
in
mm
0.056
1.4
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
24
11
0.060
1.5
31,500
3 560
5,000
7,500
2.75
73
0.94
24
45
20
0.085
2.2
2.5
56,700
6 410
4,400
6,600
3.25
85
1.44
37
71
32
0.105
2.7
94,500
10 700
4,000
6,000
4.000
107
1.44
37
104
47
0.115
2.9
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
151
69
0.130
3.3
220,500
24 900
3,000
4,500
5.375
145
2.44
62
234
86
0.150
3.8
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
310
141
0.175
4.4
434,700
49 100
2,500
3,750
6.500
180
3.00
76
450
204
0.200
5.1
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
609
276
0.220
5.6
749,700
84 700
2,100
3,150
8.250
225
4.00
101
764
347
0.120
3.0
1.5
Per Gear Mesh
Shaft sizes.
Mill Motor frame size.
G-48
162
630-852-0500
Gear
FMM Mill Motor Type
Dimensional Data
FMM Type Mill Motor Couplings
FMM Type Mill Motor Dimensional Data

AISE
ID1
LTB
LTB1
in
6.00
6.56
6.56
7.06
7.06
7.69
7.72
7.72
8.34
8.34
8.91
9.53
9.66
10.28
10.19
10.31
10.94
11.06
10.88
11.50
11.63
12.25
12.31
12.25
12.88
12.94
12.97
13.59
13.66
14.84
14.47
14.53
15.72
16.84
14.97
15.03
16.22
17.34
in
in
2.125
1.94
2.750
2.44
3.250
3.03
4.000
3.59
4.625
4.19
5.375
4.75
6.000
5.31
6.500
6.03
7.500
6.91
8.250
7.41
in
3.00
3.50
3.50
3.50
3.50
4.00
3.50
3.50
4.00
4.50
4.00
4.50
4.50
5.00
4.50
4.50
5.00
5.00
4.50
5.00
5.00
5.50
6.00
5.00
5.50
6.00
5.00
5.50
6.00
6.75
5.50
6.00
6.75
7.25
5.50
6.00
6.75
7.25
G1
BSE
FD
HD
TB
Size
1.5
2
2.5
3.5
4.5
5.5
Notes: N
N
N
N
N
N
N
N
N
N
No
602/802
603/803
604/804
603/803
604/804
606/806
603/803
604/804
606/806
608/808
606/806
608/808
610/810
612/812
608/808
610/810
612/812
614/814
610/810
612/812
614/814
616/816
618/818
614/814
616/816
618/818
614/814
616/816
618/818
620
616/816
618/818
620
622
616/816
618/818
620
622
in
in
in
in
0.13
6.00
3.97
3.00
0.13
7.00
4.86
4.00
0.19
8.38
5.84
4.63
0.19
9.44
6.84
5.63
0.25
11.00
7.91
6.50
0.25
12.50
9.25
7.50
0.31
13.63
10.38
8.50
0.31
15.31
11.56
9.50
0.31
16.75
12.72
10.50
0.31
18.00
14.00
11.50
in
1.7485 - 1.7495
1.998 - 1.999
1.998 - 1.999
1.998 - 1.999
1.998 - 1.999
2.498 - 2.499
1.998 - 1.999
1.998 - 1.999
2.498 - 2.499
2.998 - 2.999
2.498 - 2.499
2.998 - 2.999
3.248 - 3.249
3.623 - 3.624
2.998 - 2.999
3.248 - 3.249
3.623 - 3.624
4.270 - 4.2485
3.248 - 3.249
3.623 - 3.624
4.2470 - 4.2485
4.6220 - 4.6235
4.9970 - 4.9985
4.2470 - 4.2485
4.6220 - 4.6235
4.9970 - 4.9985
4.2470 - 4.2485
4.6220 - 4.6235
4.9970 - 4.9985
5.8720 - 5.8735
4.6220 - 4.6235
4.9970 - 4.9985
5.8720 - 5.8735
6.2470 - 6.2485
4.6220 - 4.6235
4.9970 - 4.9985
5.8720 - 5.8735
6.2470 - 6.2485
1.06 *
1.13 *
1.13 *
1.13
1.13
1.25
1.19
1.19
1.31
1.44
1.31
1.44
1.56
1.69
1.50
1.63
1.75
1.88
1.63
1.75
1.88
2.00
1.56
1.94
2.06
1.63
1.94
2.06
1.63
2.06
2.06
1.63
2.06
2.69
2.06
1.63
2.06
2.69
Mill Motor Hub Kw

W
in
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.75
0.50
0.75
0.75
0.75
0.75
0.75
0.75
1.00
0.75
0.75
1.00
1.25
1.25
1.00
1.25
1.25
1.00
1.25
1.25
1.50
1.25
1.25
1.50
1.50
1.25
1.25
1.50
1.50
in
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.38
0.25
0.25
0.38
0.38
0.50
0.38
0.38
0.50
0.38
0.38
0.50
0.75
0.38
0.50
0.75
0.75
0.38
0.50
0.75
0.75
* indicates: That a counterbore is required.

Bore taper is 1-14 inch per foot on diameter.
Shrouded Bolt Design available upon request for sizes 1.5 through 5.5.
Puller Holes are available for sizes 1.5 through 3.5 at an additional charge.
Inch bore and keyway tolerances conform to ANSI / AGMA 9002-B04.
1/4 inch hub standoff.
www.lovejoy-inc.com
163
G-49
OAL
Frame
Gear
FSL Type
Performance Data
FSL Type Slide Coupling
The FSL Type coupling consists of one or two modified flex hubs depending on the
maximum slide required, two sleeves, one plate with lube holes and one accessory kit.
The coupling is supplied with exposed bolts as standard. Shrouded bolts are available
upon request through size 5.5.
Features
Assembled to suit a wide range of axial movement
Plates with lube holes so both halves of the coupling will be adequately lubricated
FSL Type Performance Data

ID1 - ID2
Size
1
Nominal
Maximum
Torque
Speed
in-lb
Nm
Max Bore
Rough Stock
Weight
Max Angular
Bore
Unbal
Bal
RPM
RPM
in
Misalignment
Degrees
mm
in
mm
lbs
kg
7,600
850
6,000
9,000
1.625
42
0.44
11
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
19
31,500
3 560
5,000
7,500
2.750
73
0.94
24
34
15
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
37
54
25
94,500
10 700
4,000
6,000
4.000
107
1.44
37
80
36
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
130
59
1.5
220,500
24 900
3,000
4,500
5.375
145
2.44
62
190
86
Per Gear Mesh
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
250
114
434,700
49 100
2,500
3,750
6.500
180
3.00
76
380
173
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
520
236
749,700
84 700
2,100
3,150
8.250
225
4.00
101
650
295
1,008,000
113 900
2,000
3,000
9.500
255
5.75
139
950
431
Distance between shaft ends (maximum-minimum shaft separation).
Shaft sizes.
Amount of slide required.
G-50
164
630-852-0500
Gear
FSL Type
Dimensional Data
FSL Type Slide Couplings
Shrouded Bolt Design

Also Available
1 Hub Reversed
And Modified
2 Hubs Reversed
And Modified
FSL Type Dimensional Data

OAL
OAL1
L1
L2
LTB
LTB1
AP1
Rough Stock
Std
Slide
Max
Min
Bore
Hub
Hub
ID1 - ID2
Max Bore
FD
HD
One Hub
Two Hubs
Std
Slide
Reversed
Reversed
Hub
Half
Size
in
in
in
in
in
in
in
in
in
in
in
in
3.81
4.13
1.75
2.06
1.625
42
0.44
11
1.59
1.50
0.41
0.31
4.56
3.06
2.31
1.5
4.25
4.50
2.00
2.25
2.125
56
0.69
18
1.84
1.75
0.34
0.31
6.00
3.97
3.00
5.69
6.38
2.50
3.19
2.750
73
0.94
24
2.34
2.25
0.78
0.31
7.00
4.86
4.00
2.5
7.03
7.81
3.13
3.91
3.250
85
1.44
37
2.94
2.78
0.94
0.38
8.38
5.84
4.63
8.03
8.69
3.69
4.34
4.000
107
1.44
37
3.50
3.13
1.03
0.38
9.44
6.84
5.63
3.5
9.19
9.75
4.31
4.88
4.625
125
1.81
46
4.09
3.59
1.06
0.44
11.00
7.91
6.50
mm
in
mm
10.44
11.13
4.88
5.56
5.375
145
2.44
62
4.56
3.94
1.31
0.63
12.50
9.25
7.50
4.5
12.00
13.06
5.47
6.53
6.000
165
3.00
76
5.13
4.50
1.69
0.69
13.63
10.38
8.50
13.72
15.06
6.19
7.53
6.500
180
3.00
76
5.84
5.22
1.97
0.69
15.31
11.56
9.50
5.5
15.34
16.56
7.06
8.28
7.500
200
4.00
101
6.72
5.88
2.06
0.69
16.75
12.72
10.50
16.53
17.94
7.56
8.97
8.250
225
4.00
101
7.16
7.09
1.47
0.81
18.00
14.00
11.50
19.06
20.38
8.88
10.19
9.500
255
5.75
139
8.38
7.78
1.91
1.00
20.75
15.75
13.00
Notes: N
N
N
N
N
N
N
N
1 indicates: AP Max = Maximum slide per coupling half.

Inch bore and keyway tolerances conform to AGMA 9002-B04.
www.lovejoy-inc.com
165
G-51
Gear
FSLX Type
Performance Data
FSLX Type Long Slide Couplings
The FSLX Type basic coupling consists of a standard flex half and a custom
designed long slide half. The standard flex half can be replaced by a reversed and
modified hub for additional slide requirement. These couplings are also supplied with
a plate with lube holes. The coupling is supplied with exposed bolts as standard.
Shrouded bolts available upon request through size 5.5.
Features
Assembled to suit a wide range of axial movement
Plates with lube holes so both halves of the coupling will be adequately lubricated
FSLX Type Performance Data

ID1 - ID2
Nominal
Maximum
Torque
Size
Max Bore
Rough Stock
Speed
Weight
Max Angular
Bore
Unbal
Bal
Misalignment
Degrees
in-lb
Nm
RPM
RPM
in
1.5
18,900
2 140
5,500
8,250
2.125
31,500
3 560
5,000
7,500
2.750
2.5
56,700
6 410
4,400
6,600
94,500
10 700
4,000
6,000
3.5
151,200
17 100
3,500
220,500
24 900
3,000
4.5
302,400
34 200
434,700
5.5
573,300
mm
in
mm
lbs
kg
56
0.69
18
19
73
0.94
24
34
15
3.250
85
1.44
37
54
25
4.000
107
1.44
37
80
36
5,250
4.625
125
1.81
46
130
59
1.5
4,500
5.375
145
2.44
62
190
86
Per Gear Mesh
2,700
4,050
6.000
165
3.00
76
250
114
49 100
2,500
3,750
6.500
180
3.00
76
380
173
64 800
2,200
3,300
7.500
200
4.00
101
520
236
749,700
84 700
2,100
3,150
8.250
225
4.00
101
650
295
1,008,000
113 900
2,000
3,000
9.500
255
5.75
139
950
431
Distance between shaft ends (maximum-minimum shaft separation).
Shaft sizes.
Amount of slide required.
HL Dimension.
LTB2 Dimension.
G-52
166
630-852-0500
Gear
FSLX Type
Dimensional Data
FSLX Type Long Slide Couplings
Long Slide Half
Standard Half
Alternate Type hub shaft

contact is deep inside hub
One Hub reversed with

long slide half
FSLX Type Dimensional Data

OAL
L1
L2
Std
Slide
Hub
Half
ID1 - ID2
Max Bore
LTB
LTB2
AP1
AP2
AP3
Rough
Std
Slide
Min
Long
Long Slide
Long Slide
Stock
Hub
Hub
Slide
w/one Hub
Both Ends
Max
Reversed
Max
Bore
HL
FD
HD
Max
Size
in
in
in
in
in
mm
in
in
in
in
in
in
in
in
in
in
1.5
10.41
2.00
8.41
2.125
56
0.69
18
1.84
2.19
0.31
3.38
3.72
6.75
4.88
6.00
3.97
3.00
10.88
2.50
8.38
2.750
73
0.94
24
2.34
2.69
0.31
3.31
4.09
6.63
4.91
7.00
4.86
4.00
2.5
13.59
3.13
10.47
3.250
85
1.44
37
2.94
3.28
0.38
4.16
5.09
8.31
6.13
8.83
5.84
4.63
21.72
3.69
18.03
4.000
107
1.44
37
3.50
3.84
0.38
7.78
8.81
15.56
10.06
9.44
6.84
5.63
3.5
22.38
4.31
18.06
4.625
125
1.81
46
4.09
4.44
0.44
7.66
8.72
15.31
10.19
11.00
7.91
6.50
23.00
4.88
18.13
5.375
145
2.44
62
4.56
5.00
0.63
7.50
8.81
15.00
10.31
12.50
9.25
7.50
4.5
23.75
5.47
18.28
6.000
165
3.00
76
5.13
5.56
0.69
7.38
9.06
14.75
10.56
13.63
10.38
8.50
24.16
6.19
17.97
6.500
180
3.00
76
5.84
6.28
0.69
7.06
9.03
14.13
10.56
15.31
11.56
9.50
5.5
25.09
7.06
18.03
7.500
200
4.00
101
6.72
6.88
0.69
6.81
8.88
13.63
10.88
16.75
12.72
10.50
25.66
7.56
18.09
8.250
225
4.00
101
7.16
7.66
0.81
6.81
8.28
13.63
10.88
18.00
14.00
11.50
27.06
8.88
18.19
9.500
255
5.75
139
8.38
8.94
1.00
6.81
8.72
13.63
10.88
20.75
15.75
13.00
Notes: N
N
N
N
N
N
N
mm

www.lovejoy-inc.com
167
G-53
Gear
FSPCR Type
Performance Data
FSPCR Type Spacer Couplings
The FSPCR Type coupling consists of two flex hubs, two sleeves, one spacer and two
accessory kits. This coupling is supplied with exposed bolts as standard. Shrouded bolts are
Features
Removal of spacer provides adequate space for the removal of either coupling half
without moving the driver or driven units
FSPCR Type Performance Data

ID1 - ID2
Nominal
Maximum
Speed
Unbal
in-lb
Rough Stock
Torque
Size
Max Bore
Less
Misalignment
Spacer
Degrees
RPM
RPM
in
in
mm
lbs
850
6,000
9,000
1.625
42
0.44
11
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
19
31,500
3 560
5,000
7,500
2.750
73
0.94
24
34
15
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
37
54
25
mm
Max Angular
7,600
Nm
Bore
Bal
Weight
kg
94,500
10 700
4,000
6,000
4.000
107
1.44
37
80
36
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
130
59
1.5
220,500
24 900
3,000
4,500
5.375
145
2.44
62
190
86
Per Gear Mesh
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
250
114
434,700
49 100
2,500
3,750
6.500
180
3.00
76
380
173
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
520
236
749,700
84 700
2,100
3,150
8.250
225
4.00
101
650
295
1,008,000
113 900
2,000
3,000
9.500
255
5.00
127
950
431
Note:
N 1 indicates: Maximum RPM of spacer set determined by critical speed of spacer.
Shaft sizes.
G-54
168
630-852-0500
Gear
FSPCR Type
Dimensional Data
FSPCR Type Spacer Couplings
Shrouded bolt design also

available
FSPCR Type Dimensional Data

OAL
AD
ID1 - ID2
Max Bore
LTB
BSE
in
in
FD
HD
D1
D2
Rough Stock
Bore
Size
in
in
in
in
mm
in
2.04
1.625
42
0.44
11
1.69
Determined
2.32
2.125
56
0.69
18
1.94
by
2.94
2.750
73
0.94
24
2.44
Shaft
3.47
3.250
85
1.44
37
Separation
3.97
4.000
107
1.44
37
3.5
4.57
4.625
125
1.81
46
5.00
5.375
145
2.44
4.5
5.50
6.000
165
3.00
6.34
6.500
180
5.5
7.04
7.500
200
8.35
8.250
9.82
9.500
1
1.5
2
2.5
3
Notes: N
N
N
N
N
N
N
mm
in
in
in
in
in
0.06
in
2.31
3.06
2.31
3.00
2.41
Determined
0.06
3.00
3.97
3.00
3.75
3.13
by
0.06
4.00
4.86
4.00
4.75
4.00
3.03
Customer
0.09
4.63
5.84
4.63
5.50
4.78
3.59
Specs
0.09
5.63
6.84
5.63
6.50
5.75
4.19
0.13
6.50
7.91
6.50
7.38
6.63
62
4.75
0.13
7.50
9.25
7.50
8.63
7.75
76
5.31
0.16
8.50
10.38
8.50
9.38
8.50
3.00
76
6.03
0.16
9.50
11.56
9.50
10.38
9.56
4.00
101
6.91
0.16
10.50
12.72
10.50
11.44
10.56
225
4.00
101
7.41
0.16
11.50
14.00
11.50
12.38
11.44
255
5.00
127
8.69
0.19
13.00
15.75
13.00
14.00
13.00

www.lovejoy-inc.com
169
G-55
Gear
FLEF Type
Performance Data
FLEF Type Limited End Float Couplings
The FLEF Type coupling consists of two flex hubs, two sleeves, one accessory kit and a
steel plate to limit the movement. This coupling is supplied with exposed bolts as standard.
Shrouded bolts are available upon request through size 5.5.
Features
Provides and maintains restriced end float in sleeve bearings and rotor systems where
thrust is not permitted
Optional flow-through steel plate with lube holes available
FLEF Type Performance Data

ID1 - ID2
Nominal
Maximum
Torque
Size
in-lb
Max Bore
Rough Stock
Speed
Nm
Weight
Bore
Unbal
Bal
RPM
RPM
in
mm
in
Parallel
Max Angular
Misalignment
Misalignment
Degrees
mm
lbs
kg
in
mm
7,600
850
6,000
9,000
1.625
42
0.44
11
0.056
1.4
1.5
18,900
2 140
5,500
8,250
2.125
56
0.69
18
19
0.060
1.5
31,500
3 560
5,000
7,500
2.750
73
0.94
24
34
15
0.085
2.2
2.5
56,700
6 410
4,400
6,600
3.250
85
1.44
37
54
25
0.105
2.7
94,500
10 700
4,000
6,000
4.000
107
1.44
37
80
36
0.115
2.9
3.5
151,200
17 100
3,500
5,250
4.625
125
1.81
46
130
59
0.130
3.3
1.5
220,500
24 900
3,000
4,500
5.375
145
2.44
62
190
86
0.150
3.8
Per Gear Mesh
4.5
302,400
34 200
2,700
4,050
6.000
165
3.00
76
250
114
0.175
4.4
434,700
49 100
2,500
3,750
6.500
180
3.00
76
380
173
0.200
5.1
5.5
573,300
64 800
2,200
3,300
7.500
200
4.00
101
520
236
0.220
5.6
749,700
84 700
2,100
3,150
8.250
225
4.00
101
650
295
0.120
3.0
1,008,000
113 900
2,000
3,000
9.500
255
5.00
127
950
431
0.135
3.4
Shaft sizes.
Amount of thrust on either or both shafts.
G-56
170
630-852-0500
Gear
FLEF Type
Dimensional Data
FLEF Type Limited End Float Couplings
LEF
PLATE
FLEF Type Dimensional Data

OAL
ID1 - ID2
Max Bore
LTB
BSE
Rough Stock
F1
ST
FD
HD
in
in
in
(ref)
Bore
Size
in
3.56
1.625
42
0.44
1.5
4.06
2.125
56
0.69
5.06
2.750
73
0.94
2.5
6.34
3.250
85
1.44
7.47
4.000
107
3.5
8.59
4.625
9.88
5.375
4.5
11.06
12.59
5.5
6
7
Notes: N
N
N
N
N
N
N
N
in
mm
in
mm
in
in
in
in
11
1.69
0.19
0.13
0.13
4.56
3.06
2.31
18
1.94
0.19
0.13
0.13
6.00
3.97
3.00
24
2.44
0.19
0.13
0.13
7.00
4.86
4.00
37
3.03
0.28
0.19
0.19
8.38
5.84
4.63
1.44
37
3.59
0.28
0.19
0.19
9.44
6.84
5.63
125
1.81
46
4.19
0.31
0.25
0.19
11.00
7.91
6.50
145
2.44
62
4.75
0.38
0.25
0.25
12.50
9.25
7.50
6.000
165
3.00
76
5.31
0.44
0.25
0.31
13.63
10.38
8.50
6.500
180
3.00
76
6.03
0.53
0.31
0.38
15.31
11.56
9.50
14.34
7.500
200
4.00
101
6.91
0.53
0.31
0.38
16.75
12.72
10.50
15.28
8.250
225
4.00
101
7.41
0.47
0.31
0.31
18.00
14.00
11.50
17.94
9.500
255
5.00
127
8.69
0.56
0.38
0.38
20.75
15.75
13.00
1 indicates: F is the total end float. (May be modified.)

www.lovejoy-inc.com
171
G-57
Gear
FRR Type
Performance Data
FRR Type Rigid-Rigid Couplings
The F Type coupling consists of two rigid hubs and one accessory kit. This coupling is supplied
with exposed bolts as standard. Shrouded bolts are available upon request through size 5.5.
Features
All Steel construction
Torque capacities that exceed the mild steel shafts to be coupled
Rigid Half coupling interchangeable with industry standards
FRR Type Performance Data

ID1 - ID2
Size
Nominal
Maximum
Torque
Speed
in-lb
Nm
Max Bore
Weight
Rough Stock
Max Angular
Bore
Misalignment
Unbal
Bal
RPM
RPM
in
mm
in
mm
Degrees
lbs
kg
7,600
850
6,000
9,000
2.125
56
solid
solid
10
1.5
18,900
2 140
5,500
8,250
2.813
76
solid
solid
20
5
9
31,500
3 560
5,000
7,500
3.500
95
solid
solid
34
15
2.5
56,700
6 410
4,400
6,600
4.250
114
solid
solid
60
27
94,500
10 700
4,000
6,000
4.875
134
solid
solid
91
41
3.5
151,200
17 100
3,500
5,250
5.625
150
solid
solid
143
65
220,500
24 900
3,000
4,500
6.500
176
solid
solid
211
96
4.5
302,400
34 200
2,700
4,050
7.625
202
solid
solid
289
131
434,700
49 100
2,500
3,750
8.750
230
4.00
101
417
189
5.5
573,300
64 800
2,200
3,300
9.500
260
4.50
114
541
246
749,700
84 700
2,100
3,150
10.500
285
5.50
127
724
329
1,008,000
113 900
2,000
3,000
12.000
320
5.75
139
1,084
492
Shaft sizes.
Submit drawing if available.
G-58
172
630-852-0500
Gear
FRR Type
Dimensional Data
FFR Type Rigid-Rigid Couplings
FRR Type Dimensional Data

OAL
OAL2
ID1 - ID2
LTB
Max Bore
BSE
FD
HD
Rough Stock
Bore
Size
in
in
mm
in
mm
in
in
in
in
in
3.31
1.66
2.125
56
solid
solid
1.56
0.19
4.56
3.06
1.5
3.88
1.94
2.813
76
solid
solid
1.84
0.19
6.00
3.97
4.75
2.38
3.500
95
solid
solid
2.28
0.19
7.00
4.86
2.5
6.00
3.00
4.250
114
solid
solid
2.91
0.19
8.38
5.84
7.00
3.50
4.875
134
solid
solid
3.41
0.19
9.44
6.84
3.5
8.13
4.07
5.625
150
solid
solid
3.97
0.19
11.00
7.91
4
4.5
9.25
4.63
6.500
176
solid
solid
4.44
0.38
12.50
9.25
10.44
5.22
7.625
202
solid
solid
5.03
0.38
13.63
10.38
11.75
5.88
8.750
230
4.00
101
5.69
0.38
15.31
11.56
5.5
12.69
6.35
9.500
260
4.50
114
6.16
0.38
16.75
12.72
14.88
7.44
10.500
285
5.50
127
7.25
0.50
18.00
14.00
17.88
8.94
12.000
320
5.75
139
8.69
0.63
20.75
15.75
Notes: N
N
N
N
N
N
N

www.lovejoy-inc.com
173
G-59
Gear
FLA Type
Performance Data
FLA Type Flex-Flex All-Metal Labyrinth Seal Couplings
The FLA Type coupling consists of two special flex hubs, Two sleeves and one accessory kit. This
coupling is supplied with exposed bolts as standard. Shrouded bolts are available upon request
through size 5.5.
Features
All-Metal Labyrinth Seals
AISI 4140 Alloy Steel Construction
FLA Type Performance Data

ID1 - ID2
Nominal
Maximum
Max Bore
Rough Stock
Speed
Standard
Bore
Torque
Unbal
Bal
RPM
RPM
in
mm
in
Parallel
Max Angular
Misalignment
Misalignment
Keyway
Degrees
Size
in-lb
Nm
1.5
15,000
1 700
12,000
18,000
1.625
41
35,500
4 000
9,300
13,950
2.125
53
2.5
Weight
mm
lbs
0.38
17.6
0.5
12
29.1
kg
in
mm
0.028
0.7
13
0.035
0.9
69,300
7 800
7,900
11,850
2.750
69
0.75
19
50.9
23
0.044
1.1
118,900
13 400
6,800
10,200
3.125
79
1.13
28
74.4
34
0.052
1.3
3.5
188,500
21 300
6,000
9,000
3.750
95
1.50
38
120
55
0.061
1.5
1.5
283,800
32 100
5,260
7,890
4.250
107
1.50
38
185
84
0.700
1.8
Per Gear Mesh
4.5
393,800
44 500
4,770
7,155
4.750
120
1.50
38
240
109
0.079
2.0
551,300
62 300
4,300
6,450
5.500
139
2.50
63
365
166
0.087
2.2
5.5
732,500
82 800
3,880
5,820
5.875
149
3.00
76
435
198
0.096
2.4
952,500
107 600
3,600
5,400
6.500
165
4.00
101
538
244
0.105
2.7
1,512,500
170 900
3,000
4,500
8.0001
203
4.50
114
860
390
0.122
3.1
Note:
N 1 Indicates: Maximum bore for square keyway.
Shaft sizes.
G-60
174
630-852-0500
Gear
FLA Type
Dimensional Data
FLA Type All Metal Labyrinth Seal Couplings
FLA Type Dimensional Data

OAL
ID1 - ID2
LTB
BSE
FD
HD
Max Bore
Rough Stock
C/L - C/L
Puller
Standard
Bore
of Teeth*
Holes
Keyway
Size
in
in
in
mm
in
1.5
2
4.19
1.50
1.625
41
0.38
5.19
1.50
2.125
53
0.50
2.5
6.44
1.75
2.750
69
0.75
7.69
1.75
3.125
79
3.5
8.88
2.25
3.750
95
10.13
2.50
4.250
4.5
11.38
2.50
4.750
12.63
3.00
5.5
14.13
1.88
15.13
2.00
6.500
17.75
2.25
8.0001
Notes: N
N
N
N
N
N
N
N
N
mm
in
in
in
in
in
in
1.94
12
2.44
0.13
6.00
3.97
2.19
3.25
1/4-20
0.13
7.00
4.91
2.88
4.00
38-16
19
3.03
0.19
8.38
5.91
3.63
5.00
1/2-13
1.13
1.50
28
3.59
0.19
9.44
6.91
4.25
6.00
5/8-11
38
4.19
0.25
11.00
7.91
5.00
7.00
5/8-11
107
120
1.50
38
4.75
0.25
12.50
9.25
5.75
8.00
7/8-9
1.50
38
5.31
0.31
13.63
10.38
6.50
9.00
1-8
5.500
5.875
139
2.50
63
6.03
0.31
15.31
11.56
7.31
10.00
1-8
149
3.00
76
6.91
0.31
16.75
12.81
8.00
11.00
1-8
165
4.00
101
7.41
0.31
18.00
14.00
8.81
12.00
1-8
203
4.50
114
8.69
0.38
20.75
15.75
10.31
14.00
1 1/4-7
1 indicates: Maximum bore for square keyway.

* indicates: Center line to center line of teeth.
www.lovejoy-inc.com
175
G-61
Gear
FLAFR Type
Performance Data
FLAFR Type Flex-Rigid All-Metal Labyrinth Seal Couplings
The FLAFR Type coupling consists of one special flex hub, one rigid hub, one sleeve and one
accessory kit. This coupling is supplied with exposed bolts as standard. Shrouded bolts are
Features
All-metal labyrinth seal
AISI 4140 alloy steel construction (flex half)
Provides angular misalignment only
FLAFR Type Performance Data

ID1
ID2
ID1
ID2
Nominal
Maximum
Flex Hubs
Flex Hubs
Rigid Hubs
Rigid Hubs
Torque
Speed
Max Bore
Rough Stock
Max Bore
Rough Stock
Misalignment
Standard
Bore
Standard
Bore
Degrees
Unbal
Bal
Keyway
Weight
Max Angular
Keyway
Size
in-lb
Nm
RPM
RPM
in
1.5
15,000
1 700
12,000
18,000
1.625
41
0.38
2.813
76
0.75
19
19
35,500
4 000
9,300
13,950
2.125
53
0.50
12
3.500
95
1.00
25
31
14
2.5
3
mm
in
mm
in
mm
in
mm
lbs
kg
69,300
7 800
7,900
11,850
2.750
69
0.75
19
4.250
114
1.50
38
55
25
118,900
13 400
6,800
10,200
3.125
79
1.13
28
4.875
134
1.75
44
83
38
1.5
3.5
188,500
21 300
6,000
9,000
3.750
95
1.50
38
5.625
150
2.50
63
131
60
Per
283,800
32 100
5,260
7,890
4.250
107
1.50
38
6.500
176
3.00
76
193
88
Gear
Mesh
4.5
393,800
44 500
4,770
7,155
4.750
120
1.50
38
7.625
202
3.50
88
258
117
551,300
62 300
4,300
6,450
5.500
139
2.50
63
8.750
230
4.00
101
383
174
5.5
732,500
82 800
3,880
5,820
5.875
149
3.00
76
9.500
260
4.50
114
436
198
952,500
107 600
3,600
5,400
6.500
165
4.00
101
10.500
285
5.00
127
536
243
1,512,500
170 900
3,000
4,500
8.0001
203
4.50
114
12.000
320
5.50
139
851
386
Note:
N 1 indicates: Maximum bore for square keyway.
Shaft sizes.
G-62
176
630-852-0500
Gear
FLAFR Type
Dimensional Data
FLAFR Type Flex-Rigid All Metal Labyrinth Seal Couplings
FLAFR Type Dimensional Data

OAL
HL
ID1
ID2
ID1
ID2
Flex Hubs
Flex Hubs
Rigid Hubs
Rigid Hubs
Max Bore
Rough
Max Bore
Rough
Flex
Rigid
Standard
Stock
Standard
Stock
Hub
Hub
Keyway
Bore
Keyway
Bore
mm
in
mm
in
mm
LTB
LTB1
BSE
FD
HD1
HD
D
Puller Holes
Size
in
in
in
in
mm
in
in
in
in
in
in
in
in
in
1.5
4.03
1.94
1.625
41
0.38
2.813
76
0.75
19
1.94
1.84
0.16
6.00
3.97
2.19
3.97
1/4-20
None
4.97
2.38
2.125
53
0.50
12
3.500
95
1.00
25
2.44
2.28
0.16
7.00
4.86
2.88
4.91
38-16 5/16-18
2.5
6.22
3.00
2.750
69
0.75
19
4.250
114
1.50
38
3.03
2.91
0.19
8.38
5.84
3.63
5.91
1/2-13
3/8-16
7.41
3.50
3.125
79
1.13
28
4.875
134
1.75
44
3.59
3.41
0.19
9.44
6.84
4.25
6.91
5/8-11
1/2-13
3.5
8.56
4.06
3.750
95
1.50
38
5.625
150
2.50
63
4.19
3.97
0.22
11.00
7.91
5.00
7.91
5/8-11
1/2-13
9.69
4.63
4.250
107
1.50
38
6.500
176
3.00
76
4.75
4.44
0.31
12.50
9.25
5.75
9.25
7/8-9
5/8-11
4.5
10.91
5.22
4.750
120
1.50
38
7.625
202
3.50
88
5.31
5.03
0.34
13.63
10.38
6.50
10.38
1-8
5/8-11
12.19
5.88
5.500
139
2.50
63
8.750
230
4.00
101
6.03
5.69
0.34
15.31
11.56
7.31
11.56
1-8
3/4-10
5.5
13.41
6.34
5.875
149
3.00
76
9.500
260
4.50
114
6.91
6.16
0.34
16.75
12.72
8.00
12.81
1-8
1-8
15.22
7.66
6.500
165
4.00
101
10.500
285
5.00
127
7.41
7.41
0.41
18.00
14.00
8.81
14.00
1-8
1-8
17.88
9.00
8.0001
203
4.50
114
12.000
320
5.50
139
8.69
8.69
0.50
20.75
15.75
10.31
15.75
1 1/4-7
1-8
Notes: N
N
N
N
N
N
N
N

www.lovejoy-inc.com
177
G-63
Gear
FLAMM and FLAMMFR Type
Performance Data
FLAMM Type Flex-Flex Mill Motor Couplings
The FLAMM Type coupling consists of one standard FLA flex hub, one universal flex
hub bored to an A.I.S.E. frame size, two sleeves and one accessory kit. This coupling
is supplied with exposed bolts as standard. Shrouded bolts are available upon request
through size 5.5.
FLAMMFR Type Flex-Rigid Mill Motor Couplings

The FLAMMFR Type coupling consists of a rigid hub, one universal flex hub bored to
A.I.S.E. frame size, one sleeve and one accessory kit. This coupling is supplied with
exposed bolts as standard. Shrouded bolts are available upon request through size 5.5.
Features
Patented Vari-Crown tooth form for long life on Flex Half

Long Universal Hub used for A.I.S.E. Motor Frames
FLAMM and FLAMMFR Type Performance Data

ID1
ID2
ID1
ID2
Nominal
Max
Flex Hub
Flex Hub
Rigid Hub
Rigid Hub
Torque
Speed
Max Bore
Rough Stock
Max Bore
Rough Stock
Misalignment
Angular
Standard
Bore
Standard
Bore
FLAMM only
Misalignment
Unbal
Size
1.5
Bal
Keyway
in-lb
Nm
RPM
RPM
in
18,900
2 140
5,500
8,250
1.625
Weight
Parallel
Keyway
mm
41
in
0.38
mm
9
in
2.813
Degrees
mm
in
mm
in
mm
76
solid
solid
lbs
24
kg
11
0.28
0.7
31,500
3 560
5,000
7,500
2.125
53
0.50
12
3.500
95
solid
solid
45
20
0.35
0.9
2.5
56,700
6 410
4,400
6,600
2.750
69
0.75
19
4.250
114
solid
solid
71
32
0.44
1.1
Max
94,500
10 700
4,000
6,000
3.125
79
1.13
28
4.875
134
solid
solid
104
47
0.52
1.3
.5
3.5
151,200
17 100
3,500
5,250
3.750
95
1.50
38
5.625
150
solid
solid
151
69
0.61
1.5
Per
220,500
24 900
3,000
4,500
4.250
17
1.50
38
6.500
176
solid
solid
234
86
0.70
1.8
Gear
4.5
302,400
34 200
2,700
4,050
4.750
120
1.50
38
7.625
202
solid
solid
310
141
0.79
2.0
Mesh
434,700
49 100
2,500
3,750
5.500
139
2.50
63
8.750
230
4.00
101
450
204
0.87
2.2
5.5
573,300
64 800
2,200
3,300
5.875
149
3.00
76
9.500
260
4.50
114
609
276
0.96
2.4
749,700
84 700
2,100
3,150
6.500
165
4.00
101
10.500
285
5.50
127
764
347
0.105
2.7
3,000
203
4.50
114
12.000
320
5.75
139
1,212
551
0.122
3.1
1,008,000 113 900
Notes: N
N

N

N

N

N

N

N

N
G-64
2,000
8.000

Shaft sizes.
Mill Motor frame size.
178
630-852-0500
Gear
Dimensional Data
Lovejoy / Seir-Bath Flanged Sleeve Gear Couplings
All Metal Labyrinth Seal Mill Motor Couplings
FLAMM and FLAMMFR Type Dimensional Data

OAL 2
OAL 3
LTB
LTB1
LTB2
BSE
BSE 1
FD
HD
HD 1
TB
Mill Mtr Hub Kw
AISE
Frame
Size
1.5
2
3.5
4.5
5.5
6
7
in
6.00
6.50
7.06
7.06
7.16
7.72
7.72
8.34
7.72
8.28
8.28
8.91
9.53
9.66
8.88
8.88
9.50
10.13
10.25
10.94
10.13
10.75
10.88
11.50
11.63
12.25
11.50
12.12
12.25
12.88
12.94
12.84
12.97
13.59
13.66
14.47
14.53
15.72
16.84
16.22
17.34
19.34
18.69
20.69
in
5.91
6.34
6.91
6.91
7.03
7.59
7.59
8.22
7.53
8.09
8.09
8.72
9.34
9.47
8.66
8.66
9.28
9.91
10.03
10.72
9.81
10.44
10.56
11.19
11.31
11.94
11.22
11.84
11.97
12.59
12.66
12.50
12.63
13.25
13.31
13.72
13.78
14.97
16.09
16.22
17.34
19.34
18.69
20.69
in
1.94
in
1.84
2.44
2.28
3.03
2.28
3.59
2.91
4.19
3.97
4.75
4.44
5.31
5.03
6.03
5.69
6.91
6.16
7.41
7.41
8.69
8.69
in
3.00
3.00
3.50
3.50
3.00
3.50
3.50
4.00
3.00
3.50
3.50
4.00
4.50
4.50
3.50
3.50
4.00
4.50
4.50
5.00
4.00
4.50
4.50
5.00
5.00
5.00
4.50
5.00
5.00
5.50
6.00
5.00
5.00
5.50
6.00
5.50
6.00
6.75
7.25
6.75
7.25
9.25
7.25
9.25
in
1.06
1.06
1.13
1.13
1.13
1.19
1.19
1.31
1.13
1.19
1.19
1.31
1.44
1.56
1.19
1.19
1.31
1.44
1.56
1.75
1.38
1.50
1.63
1.75
1.88
2.00
1.69
1.81
1.94
2.06
1.63
1.81
1.94
2.06
1.63
2.06
1.63
2.06
2.69
2.06
2.69
2.69
2.75
2.75
in
0.13
in
0.16
in
6.00
in
3.97
in
2.19
in
3.97
0.13
0.16
7.00
4.91
2.88
4.86
0.19
0.19
8.38
5.91
3.63
5.84
0.19
0.19
9.44
6.91
4.25
6.84
0.25
0.22
11.00
7.91
5.00
7.91
0.25
0.31
12.50
9.25
5.75
9.25
0.31
0.34
13.63
10.38
6.50
10.38
0.31
0.34
15.31
11.56
7.31
11.56
0.31
0.34
16.75
12.81
8.00
12.72
0.31
0.41
18.00
14.00
8.81
14.00
0.38
0.50
20.75
15.75
10.31
15.75
Notes: N Bore taper is 1-1/4 inch per foot on diameter.

N Exposed Bolt Design is standard.
N Shrouded Bolt Design available upon request for sizes 1.5
through 5.5
.
N Puller Holes are standard on sizes 4 through 7.
N Puller Holes are available for sizes 1.5 through 3.5 at an additional charge.
www.lovejoy-inc.com
in
1.7485 - 1.7495
1.7485 - 1.7495
1.998 - 1.999
1.998 - 1.999
1.7485 - 1.7495
1.998 - 1.999
1.998 - 1.999
2.498 - 2.499
1.7485 - 1.7495
1.998 - 1.999
1.998 - 1.999
2.498 - 2.499
2.998 - 2.999
3.248 - 3.249
1.998 - 1.999
1.998 - 1.999
2.498 - 2.499
2.998 - 2.999
3.248 - 3.249
3.623 - 3.624
2.498 - 2.499
2.998 - 2.999
3.248 - 3.249
3.623 - 3.624
4.2470 - 4.2485
4.6220 - 4.6235
3.248 - 3.249
6.623 - 3.624
4.2470 - 4.2485
4.6220 - 4.6235
4.9970 - 4.9985
3.623 - 3.624
4.2470 - 4.2485
4.6220 - 4.6235
4.9970 - 4.9985
4.6220 - 4.6235
4.9970 - 4.9985
5.8720 - 5.8735
6.2470 - 6.2485
5.8720 - 5.8735
6.2470 - 6.2485
6.9970 - 6.9985
6.2470 - 6.2485
6.9970 - 6.9985
in
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.50
0.75
0.75
0.50
0.50
0.50
0.75
0.75
0.75
0.50
0.75
0.75
0.75
1.00
1.25
0.75
0.75
1.00
1.25
1.25
0.75
1.00
1.25
1.25
1.25
1.25
1.50
1.50
1.50
1.50
1.50
1.50
1.50
in
0.13
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.38
0.28
0.25
0.25
0.38
0.38
0.50
0.25
0.38
0.38
0.50
0.38
0.50
0.75
0.56
0.75
0.75
0.50
0.75
0.75
2.5
No
602/802
602/802
603/803
604/804
602/802
603/803
604/804
606/806
602/802
603/803
604/804
606/806
608/808
610/810
603/803
604/804
606/806
608/808
610/810
612/812
606/806
608/808
610/810
612/812
614/814
616/816
610/810
612/812
614/814
616/816
618/818
612/812
614/814
616/816
618/818
616/816
618/818
620
622
620
622
624
622
624
N Interference bores with no set screws are standard unless

otherwise specified.
N Inch bore and keyway tolerances conform to AGMA 9002-B04.
N For metric bore and keyway tolerances, consult Lovejoy
Engineering Section.
179
G-65
Gear
FA Type
Performance Data
FA Type Alloy Steel Flex-Flex Couplings
The FA Type coupling consists of two flex hubs, two sleeves and one accessory kit. This coupling
is supplied with exposed bolts as standard. Shrouded bolts are available upon request through
size 5.5.
Features
Molded seals maintain proper lubricant retention during misalignment conditions
AISI 4140 Alloy Steel Construction
FA Type Performance Data

ID1 - ID2
Nominal
Maximum
Max Bore
Rough Stock
Speed
Standard
Bore
Torque
Unbal
Nm
Bal
Weight
Parallel
Max Angular
Misalignment
Misalignment
Keyway
Degrees
Size
in-lb
RPM
RPM
in
mm
lbs
kg
in
mm
11,300
1 280
6,000
9,000
1.625
mm
42
0.44
in
11
0.056
1.4
1.5
22,700
2 560
5,500
8,250
2.125
56
0.69
18
19
0.060
1.5
39,000
4 410
5,000
7,500
2.75
73
0.94
24
34
15
0.085
2.2
2.5
69,300
7 930
4,400
6,600
3.25
88
1.44
37
54
25
0.105
2.7
118,000
13 300
4,000
6,000
4.000
107
1.44
37
80
36
0.115
2.9
3.5
177,000
20 000
3,500
5,250
4.625
124
1.81
46
130
59
0.130
3.3
1.5
263,400
29 760
3,000
4,500
5.375
147
2.44
62
190
86
0.150
3.8
Per Gear Mesh
4.5
354,000
40 000
2,700
4,050
6.000
167
3.00
76
250
114
0.175
4.4
508,600
57 470
2,500
3,750
6.500
176
3.00
76
380
173
0.200
5.1
5.5
670,700
75 790
2,200
3,300
7.500
202
4.00
101
520
236
0.220
5.6
877,100
99 110
2,100
3,150
8.250
225
4.00
101
650
295
0.120
3.0
1,179,300
1 332 600
2,000
3,000
9.500
255
5.00
127
950
431
0.135
3.4
Shaft sizes.
G-66
180
630-852-0500
Gear
FA Type
Dimensional Data
FA Type Alloy Steel Couplings
FA Type Dimensional Data

OAL
AD
ID1 - ID2
LTB
Max Bore
Rough Stock
Standard
Bore
BSE
FD
HD
Keyway
Size
in
in
in
mm
in
mm
in
in
in
in
in
3.50
4.19
1.625
42
0.44
11
1.69
0.13
4.56
3.06
2.31
1.5
4.00
4.75
2.125
56
0.69
18
1.94
0.13
6.00
3.97
3.00
5.00
6.00
2.750
73
0.94
24
2.44
0.13
7.00
4.86
4.00
2.5
6.25
7.13
3.250
88
1.44
37
3.03
0.19
8.38
5.84
4.63
7.38
8.13
4.000
107
1.44
37
3.59
0.19
9.44
6.84
5.63
3.5
8.63
9.38
4.625
124
1.81
46
4.19
0.25
11.00
7.91
6.50
9.75
10.25
5.375
147
2.44
62
4.75
0.25
12.50
9.25
7.50
4.5
10.94
11.50
6.000
167
3.00
76
5.31
0.31
13.63
10.38
8.50
12.38
13.00
6.500
176
3.00
76
6.03
0.31
15.31
11.56
9.50
5.5
14.13
14.38
7.500
202
4.00
101
6.91
0.31
16.75
12.72
10.50
15.13
17.00
8.250
225
4.00
101
7.41
0.31
18.00
14.00
11.50
17.75
20.00
9.500
255
5.00
127
8.69
0.38
20.75
15.75
13.00
Notes: N
N
N
N
N
N
N

www.lovejoy-inc.com
181
G-67
Gear
RA and RAHS Type
Performance Data
Lovejoy / Sier-Bath Rigid Adjustable Couplings
RA and RAHS Type Rigid Adjustable Couplings
The RA and RAHS couplings are offered in two different styles. Type II coupling
consists of two rigid hubs, adjusting nut and split ring and split ring for motor
bub. Type IV coupling consists of two rigid hubs, adjusting nut, split ring for
motor hub and spacer.
Features
Axial positioning of the pump impeller in vertical pump applications
Clearence fit bores allows for easy installation and maintenance for pump
and/or motor
Easily adjustable for vertical clearence
Removable spacer for easy maintenance
AISI 1045 Steel
Stainless Steel coupling also available
RA and RAHS Type Performance Data

HP/100
Nominal
Thrust
RPM
Torque
Capacity
in-lb
lbs
Size
Motor & Pump Hubs
Motor & Pump Hubs
Min Bore
Max Bore
in
mm
in
mm
1125
2.7
1,702
4,500
0.44
11
1.125
29
1625
8.0
5,042
11,000
0.63
16
1.625
42
2125
17.9
11,282
31,000
0.73
18
2.125
56
2625
33.8
21,302
31,000
0.88
22
2.625
70
2875
44.4
27,983
31,000
0.88
22
2.875
77
3125
57.0
35,924
41,000
1.19
30
3.125
84
3875
109.0
68,697
73,000
1.25
31
3.875
103
5000
310.0
195,378
160,000
2.38
60
5.000
135
6000
404.0
254,621
300,000
2.88
73
6.000
167
7250
712.0
448,738
300,000
4.00
101
7.250
194
8500
1148.0
723,527
350,000
4.00
101
8.500
225
10500
2164.0
1,363,861
400,000
5.00
127
10.500
276
Speed: Motor Speed or Driven RPM.
Shaft sizes.
Adjusting nut threads.
Amount of trust on either or both shafts.
Submit drawing if available.
G-68
182
630-852-0500
Gear
RA and RAHS Type
Dimensional Data
Lovejoy / Sier-Bath Rigid Adjustable Couplings
RA and RAHS Type Rigid Adjustable Couplings
Item
Description
Upper Hub - Motor
Lower hub - Pump
Spacer
Adjusting Nut, Threaded
Washer, Split
RA and RAHS Accessory Kit
RA and RAHS Accessory Kit
RA and RAHS Type Dimensional Data

STD OAL
Type II
FD
LTB
LTB1
LS
DC
SL
D1
D2
Type IV
S
Std
B.C.
Min
BOLTS
Dia
Size
in
in
in
in
in
in
in
in
in
in
in
in
in
in
Qty
Size
in
1125
5.25
9.56
3.00
1.75
2.13
1.11
2.00
0.89
1.25
0.88
1.75
1.25
4.44
1.63
1/4 - 28
2.375
1625
6.00
10.31
4.00
2.50
2.38
1.36
2.25
0.89
1.50
0.88
2.50
1.75
4.44
1.75
5/16 - 24
3.250
2125
7.13
11.44
5.13
3.13
2.81
1.80
2.69
0.89
1.75
1.00
3.13
2.25
4.44
2.63
1/2 - 20
4.250
2625
9.38
13.69
5.88
3.88
3.06
2.05
2.94
0.89
3.50
1.13
3.88
2.75
4.44
2.63
1/2 - 20
4.938
2875
10.38
14.69
6.38
4.38
3.56
2.55
3.44
0.89
3.50
1.38
4.38
3.00
4.44
2.88
1/2 - 20
5.438
3125
11.50
15.81
6.75
4.63
4.13
3.11
4.00
0.89
3.50
1.63
4.63
3.25
4.44
2.88
1/2 - 20
5.813
3875
12.75
17.06
8.94
5.88
4.50
3.48
4.38
0.89
4.00
1.75
5.88
4.00
4.44
3.13
3/4 - 16
7.625
5000
15.00
NO STD
11.75
7.50
6.25
4.63
6.00
1.38
3.00
2.44
7.50
5.13
NO STD
4.50
1 - 14
10.000
7.63
9.25
1.63
2.38
4.00
9.00
6.13
NO STD
4.75
10
1 - 14
11.500
8.81 10.75
1.94
3.69
4.75
10.75
7.38
NO STD
7.06
14
1 - 14
13.250
6000
20.88
NO STD
13.25
9.00
9.50
7250
25.19
NO STD
15.00 10.75
11.06
7500
33.56
NO STD
17.25 12.50 15.31 13.06 15.00
1.94
3.56
6.63
12.50
8.63
NO STD
7.31
12
1-1/8 - 12
15.000
10500
40.94
NO STD
20.50 15.00 18.69 16.44 18.38
1.94
4.19
8.13
15.00 10.63
NO STD
8.31
12
1-1/8 - 12
18.000
Notes: N
N
N
N
N
Clearence fit bores with set screw are standard.

RA couplings meet standard tolerances.
Inch bore and keyway tolerances conform to AINSI / AGMA 9002-B04.
RAHS couplings conform to API 610 8th edition tolerances.
www.lovejoy-inc.com
183
G-69
Gear
F Universal Hub and Puller Holes
Dimensional Data
F Type Standard and Universal Hub Dimensions
L1
Size
1
L2
L3
TW
LTB
LTB1
STD
UNIV HUB
in
in
in
in
in
in
2.75
0.44
0.75
0.50
1.69
4.00
1.5
3.13
0.56
0.81
0.56
1.94
1.50
3.63
0.56
1.25
0.63
2.44
4.50
2.5
4.22
0.75
1.53
0.75
3.03
6.50
4.44
1.03
1.69
0.88
3.59
7.00
3.5
4.63
1.31
1.88
1.00
4.19
7.50
4.97
1.47
2.16
1.13
4.75
8.25
4.5
5.19
1.50
2.56
1.25
5.31
9.00
5.06
1.59
2.94
1.50
6.03
9.50
5.5
5.56
1.97
3.19
1.75
6.91
10.50
Flex Hubs Puller Bolt Holes

B.C. Diameter
Tap Size
Size
in
UNC
Depth
None
None
None
1.5
None
None
None
3.38
5/8 - 18
0.50
2.5
3.94
3/8 - 16
0.56
4.94
1/2 - 13
0.75
3.5
5.56
1/2 - 13
0.75
6.44
5/8 - 11
0.94
4.5
7.38
5/8 - 11
0.94
8.00
3/4 - 10
1.13
5.5
9.00
1-8
1.50
9.75
1-8
1.50
11.63
1-8
1.50
14.00
1-8
1.50
15.25
1-1/4 - 7
1.88
G-70
184
630-852-0500
Gear
F Flange and Hub Gap Details
Dimensional Data
Flange Details
LS
DC
FD
CBD
B.C.
Dia
B.C.
Dia
Exposed Bolts
Bolts
Length
in
1.66
1.88
2.38
2.88
3.31
3.81
4.25
4.81
5.50
6.00
6.69
7.38
8.38
9.00
in
0.56
0.75
0.75
0.88
0.88
1.13
1.13
1.13
1.50
1.50
1.00
1.13
1.31
1.50
in
0.09
0.09
0.09
0.09
0.09
0.09
0.19
0.19
0.19
0.19
0.25
0.31
0.31
0.31
in
4.56
6.00
7.00
8.38
9.44
11.00
12.50
13.63
15.31
16.75
18.00
20.75
23.75
26.00
in
2.812
3.562
4.562
5.437
6.437
7.375
8.750
9.750
10.750
12.125
13.000
14.625
17.750
19.000
in
Qty
Size
3.750
6
1/4-28
4.812
8
3/8-24
5.875
6
1/-20
7.125
6
5/8-18
8.125
8
5/8-18
9.500
8
3/4-16
11.000
8
3/4-16
12.000 10
3/4-16
13.500
8
7/8-14
14.500 14
7/8-14
15.750 14
7/8-14
18.250 16
1-14
20.750 16 1-1/8-12
23.250 18 1-1/4-12
Normal Hub Arrangement
in
1-1/2
2
2-1/4
2-3/4
2-3/4
3-1/4
3-1/4
3-1/4
4-1/4
4-1/4
3-1/4
3-1/2
Max
Grip
in
3/4
15/16
15/16
7/8
7/8
1
1
1-1/4
1-3/4
1-3/4
23/32
5/8
in
1
1-1/4
1-1/4
1-1/4
1-1/4
1-7/16
1-7/16
1-7/16
2-1/4
2-1/4
1-1/4
1-1/4
Shrouded Bolts
Bolts
Length Min
Body
in
3.750
4.812
5.812
7.000
8.000
9.281
10.625
11.750
13.188
14.437
Qty
6
8
10
10
12
12
14
14
14
16
Size
1/4-28
3/8-24
3/8-24
1/2-20
1/2-20
5/8-18
5/8-18
5/8-18
3/8-16
3/4-16
in
3/4
1
1
1-1/8
1-1/8
1-3/8
1-3/8
1-3/8
1-7/8
1-7/8
in
9/32
9/32
9/32
3/8
3/8
7/16
7/16
7/16
5/8
5/8
L1
in
0.64
0.81
0.81
1.06
1.06
1.31
1.31
1.31
1.56
1.56
in
0.25
0.25
0.25
0.31
0.31
0.38
0.38
0.38
0.56
0.56
Max
Grip
in
7/16
7/16
7/16
1/2
1/2
5/8
5/8
5/8
1
1
EXPOSED BOLTS ONLY
1 Hub Reversed
2 Hubs Reversed
Minimum and Maximum Hub Gaps

Size
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
7
8
9
OAL
in
3.50
4.00
5.00
6.25
7.38
8.63
9.75
10.94
12.38
14.13
15.13
17.75
22.38
23.50
OAL1
in
3.81
4.25
5.81
7.03
8.03
9.19
10.44
12.00
13.72
15.34
16.53
19.06
23.13
24.25
www.lovejoy-inc.com
OAL2
in
4.13
4.50
6.38
7.81
8.69
9.75
11.13
13.06
15.06
16.56
17.94
20.38
23.88
25.00
TS
in
2.13
2.31
3.25
4.00
4.44
5.00
5.69
6.69
7.69
8.44
9.13
10.38
12.13
12.75
CL
in
0.06
0.06
0.06
0.09
0.09
0.09
0.13
0.13
0.19
0.19
0.16
0.19
0.19
0.38
P
in
0.09
0.13
0.13
0.25
0.38
0.50
0.63
0.66
0.69
1.06
0.88
1.50
2.81
2.75
185
P1
in
0.41
0.38
0.81
1.03
1.03
1.06
1.31
1.72
2.03
2.38
2.28
2.81
3.56
3.50
LTB
in
1.69
1.94
2.44
3.03
3.59
4.19
4.75
5.31
6.03
6.91
7.41
8.69
11.00
11.50
G
in
0.13
0.13
0.13
0.19
0.19
0.25
0.25
0.31
0.31
0.31
0.31
0.38
0.38
0.50
G1
in
0.44
0.38
0.81
0.97
0.84
0.81
0.94
1.38
1.66
1.53
1.72
1.69
1.13
1.25
G2
in
0.75
0.63
1.50
1.75
1.50
1.38
1.63
2.44
3.00
2.75
3.13
3.00
1.88
2.00
G-71
Size
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
7
8
9
Min
Body
CBD 1
Gear
Continuous Sleeve
Overview
Vertical Floating Shaft Type
The upper coupling is a Standard Vertical Type coupling. The

lower coupling has a hardened crowned button inserted in the
plate of the lower hub and a hardened flat button inserted in
the plate of the upper hub. The entire floating assembly rests
on these two buttons which carry the weight of the floating
assembly thus maintaining the spacing between the two lower
hubs allowing for flexibility. The hubs on the floating shaft are
flexible and the hubs of the driver and driven shafts are rigid.
Brakedrum Type
Brake Disc Type
Two different designs of brakedrum couplings are illustrated. One

shows the brakedrum as an intergal part of the sleeve and the
two hybs are standard. The other design utilizes one standard
hub and a standard sleeve with the brakedrum as part of a
special hub.
Two different designs of brake disc couplings are illustrated. One

shows the brake disc as an intergal part of the sleeve and the
two hybs are standard. The other design utilizes one standard
hub and a standard sleeve with the brakedrum as part of a
special hub.
G-72
186
630-852-0500
Gear
Continuous Sleeve
Overview
Sliding Hub Type

The sleeve is longer than standard and is designed to allow
for a predetermined amount of axial travel on one shaft. The
short hub is secured to the sleeve by means of a spacer
washer and snap ring which prevents travel. This type is also
manufactured to allow for travel of both hubs in the sleeve.
This coupling is also available with a rigid type short hub.
Jordan Type
Used on Jordan machines and refiners, this design is similar
to the Sliding Hub Type coupling except the long hub is split
and secured to the shaft with a bolt. This permits for quick
axial adjustment of the Jordan shafts in the hub.
Continuous Lubricated Type

This coupling is adapted from our Standard Type coupling,
except the standard seals have been replaced with the special
spacer washers. These washers have a snug fit in the sleeve
with sufficient clearance on the hub OD to allow for injection of
a continuous stream of lubricant.
www.lovejoy-inc.com
187
G-73
Gear
Flanged Sleeve
Overview
Limited End Float Spacer Type
The addition of plates restricts axial travel to the drive or driven

shaft. The spacer makes it possible to remove the hubs from either
shaft without disturbing the connected units.
Vertical Floating Shaft Type

The lower coupling has a hardened crowned
button inserted in the plate of the lower hub.
The entire floating assembly rest on the
button. Optional construction of the upper
coupling would be a rigid hub on the floating
shaft with a flex half on the top.
Vertical Type
This coupling has the same horsepower, RPM and misalignment
capabilities as the standard couplings of corresponding sizes. A
plate with a hardened crowned button rests on the lower shaft
which supports the weight of the sleeve.
Jordan Type
Used on Jordan machines and refiners, this design is similar to the
slide type coupling except the long hub is split and secured to the
shaft with a bolt clamp. This permits quick axial adjustment of the
Jordan shafts i this hub.
Insulated Type
Use of a non-metallic material between flanges and around the
bolts prevents any stray currents from one shaft to the other.
G-74
188
630-852-0500
Gear
Flanged Sleeve
Overview
Engineered Shear Pin Type
Brakewheel and Brake Disc Type
Shear pin couplings are primarily used to limit transmitted torque to a

redetermined load. THis in turn disconnectes the driver and driven shafts
if torque exceeds the specified limits. They are especially suited to protect
equipment when jams occur. Components are re-useable after pins shear.
The coupling will retain lubricant for a short period to allow equipment to be
shut down.
Replaceable brakewheel and brake disc piloted on the outside diameter

of a standard sleeve and/or rigid hub. Offers a choice of applying braking
effort to the load or driving motor.
Double Engagement Half Gear Type
Rigid Alloy Steel FARR Type
Both internal and external teeth in a single sleeve. Can be bolted

to a rotating flywheel, shaft or drum to connect driver or driven
machine with a shaft extension. This coupling has the same
features, ratings and misalignment capability as the standard group
of couplings.
Male/Female piloted rigid coupling coupling with keeper plates.

This coupling is used when a rigid connection is required between
the low speed shaft of a gearbox and the head shaft of a conveyor,
bucket elevator, mixer or any overhung or suspended load.
www.lovejoy-inc.com
189
G-75
Gear
Standard Flanged Sleeve Maximum Bores Inch / Metric
Dimensional Data
Standard Flanged Sleeve Maximum Bores - Inches and Millimeters
Flex Hub Maximum Bores - Interference Fit
Inch
Max
1 Square Keyway
Metric
Max
1 Rectangular Keyway
Max
Metric Keyway
Bore
Width
Depth
Bore
Width
Depth
Bore
Width
Depth
Size
in
in
in
in
in
in
mm
mm
mm
3.3
1.625
0.375
0.188
1.750
0.375
0.125
42
12
1.5
2.125
0.500
0.250
2.250
0.500
0.188
56
16
4.3
2.750
0.625
0.313
2.875
0.750
0.250
73
20
4.9
2.5
3.250
0.750
0.375
3.375
0.875
0.313
85
25
5.4
4.000
1.000
0.500
4.250
1.000
0.375
107
28
6.4
3.5
4.625
1.250
0.625
4.875
1.250
0.438
125
32
7.4
8.4
5.375
1.250
0.625
5.625
1.500
0.500
145
36
4.5
6.000
1.500
0.750
6.500
1.500
0.500
165
40
9.4
6.500
1.500
0.750
7.000
1.750
0.750
180
45
10.4
7.250
1.750
0.875
7.500
1.750
0.750
200
45
10.4
8.000
2.000
1.000
8.250
2.000
0.750
225
50
11.4
9.000
2.000
1.000
9.500
2.500
0.875
255
56
12.4
11.000
2.500
1.250
11.500
3.000
1.000
310
70
14.4
12.000
3.000
1.500
12.500
3.000
1.000
340
80
15.4
10
13.750
3.500
1.250
355
80
15.4
17.4
5.5
11
15.500
4.000
1.500
410
90
12
17.000
4.000
1.500
435
90
17.4
13
18.250
5.000
1.750
480
100
19.5
14
19.500
5.000
1.750
15
21.000
5.000
1.750
16
22.500
6.000
2.000
18
25.500
6.000
2.000
20
28.000
7.000
2.500
22
31.000
8.000
2.750
24
34.000
9.000
3.000
26
37.000
9.000
3.000
28
40.000
10.000
3.500
30
42.000
10.000
3.500
Notes: N Rectangular (reduced) keyways preferred for bores above 6-1/2 inches.
N Maximum bores may be reduced for clearance fit bore applications.
G-76
190
630-852-0500
Gear
Rigid Hub Maximum Bores Interference Fit
Dimensional Data
Rigid Hub Maximum Bores Interference Fit
Rigid Hub Maximum Bores - Interference Fit
Inch
Max
Bore
1 Square Keyway
Width
Depth
Metric
Max
1 Rectangular Keyway
Max
Bore
Width
Depth
Bore
Width
Depth
mm
in
Metric Keyway
Size
in
in
in
in
in
mm
mm
2.125
0.500
0.250
2.250
0.500
0.188
56
16
4.3
1.5
2.813
0.750
0.375
3.062
0.750
0.250
76
22
5.4
3.500
0.875
0.438
3.750
0.875
0.313
95
25
5.4
2.5
4.250
1.000
0.500
4.500
1.000
0.375
114
32
7.4
4.875
1.250
0.625
5.250
1.250
0.438
134
36
8.4
3.5
5.625
1.500
0.750
5.875
1.500
0.500
150
36
8.4
10.4
6.500
1.500
0.750
6.500
1.500
0.500
176
45
7.375
1.750
0.875
7.625
2.000
0.750
202
50
11.4
8.375
2.000
1.000
8.750
2.000
0.750
230
50
11.4
5.5
9.250
2.500
1.250
9.500
2.500
0.875
260
56
12.4
10.125
2.500
1.250
10.500
2.500
0.875
285
63
12.4
11.250
3.000
1.500
12.000
3.000
1.000
320
70
14.4
13.500
3.500
1.750
14.000
3.500
1.250
375
80
15.4
15.000
3.500
1.750
15.500
4.000
1.500
415
90
17.4
10
17.000
4.000
1.500
455
100
19.5
11
18.500
5.000
1.750
500
100
19.5
12
20.250
5.000
1.750
13
22.000
5.000
1.750
14
23.500
6.000
2.000
15
24.250
6.000
2.000
16
26.000
6.000
2.000
18
28.000
7.000
2.500
20
31.000
8.000
2.750
22
34.000
8.000
2.750
24
37.000
9.000
3.000
26
40.000
10.000
3.500
28
43.000
11.000
3.750
30
46.000
11.000
3.750
Notes: N Rectangular (reduced) keyways preferred for bores above 6-1/2 inches.
N Maximum bores may be reduced for clearance fit bore applications.
www.lovejoy-inc.com
191
G-77
4
4.5
Gear
Coupling Grease
Why Coupling Grease?
Adequate lubrication is essential for satisfactory gear coupling

operation. Lovejoy Gear Coupling Grease is specifically
designed for gear coupling applications to increase coupling
life while drastically reducing maintenance time. Its high
viscosity base oil and tackifier combine to keep the grease in
place and prevent separation and it is in complete compliance
with NSI/AGMA 9001-B97 lubrication recommendations.
Lovejoy Coupling Grease is dark brown in color and
manufactured with a lithium soap/polymer thickener, which
has superior resistance to oil separation when subjected to
high centrifugal forces normally found in couplings. Bearing
or general purpose greases tend to separate and lose
effectiveness due to high centrifugal forces on the various
ingredients at high rotational speeds. These high centrifugal
forces encountered in couplings separate the base oil from
the thickeners. Heavy thickeners, which have no lubrication
qualities, accumulate in the gear tooth mesh area resulting
in premature coupling failure. Lovejoy Gear Coupling Grease
is designed to highly resistant to centrifugal separation of the
oil and thickener, which allows the lubricant to be used for a
relatively long period of time.
One of the secrets to the success of Lovejoy Gear Coupling
Grease is the variable consistency throughout the working
cycle of the application. The consistency of our gear coupling
grease changes with the operating conditions. Working of the
lubricant under actual service conditions causes the grease
to become semi-fluid, functionally solash lubricating the wear
surfaces of the coupling. As the grease cools, it returns to the
original consistency, thereby preventing leakage.
Typical Properties of Lovejoy Gear Coupling Grease

NLGI Grade
0/1
Appearance
Dark Brown, Tacky
Lithium Soap / Polymer, wt%

Viscosity
Minimizing of coupling wear

Resistance to water washing
Corrosion and rust protection
High load carrying capabilities
Extended relubrication frequency
>3200
@ 100 C, cSt
>50
Worked, 60x
350
Worked, 10,000, % Change
10
Dropping Point, F
Centrifugal Oil Separation, vol%
Water Spray-Off, wt%
320 (160 C)
None
>3
Rust Protection
Pass
Timken, OK Load, lbs
40+
Four-Bal EP
Use at temperatures up to 325 F

Staying in place under high speeds
Resistance to centrifugal separation
@ 40 C, cST
Penetration. Dmm
Lovejoy Gear Coupling Grease is available from stock in 14

oz. cartridges, 1 lb. and 5 lb. cans.
Features
10.0
Load Wear Index, kgf
68
Weld Point, kgf
400
Four-Ball Wear, mm
1 hr, 75 C, 1200 RPM, 40 kgf
Reduction in down time & maintenance cost
0.4
Guide to Usable Temperature
Lovejoy Gear Coupling Grease has a consistency which

overlaps the NLGI grades 0 and 1. This grease is specially
formulated with a lithium/polymer thickener and fortified with
corrosion, oxidation, extreme pressure, and a effective rust
inhibitor additive package.
G-78
Min, F
192
Below -20 (-29 C)
Continuous Service, Max, F
250 (121 C)
Short Exposure, Max, F
325 (163 C)
630-852-0500

Gear Coupling Catalogue PDF

Uploaded by

Copyright:

Available Formats

Gear Coupling Catalogue PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Gear Coupling Catalogue PDF

Uploaded by

Copyright:

Available Formats

JW

Nyflex and Mite

Lovejoy / Sier-Bath Continuous Sleeve and Flanged Sleeve Couplings

Continuous Sleeve Series

Flanged Sleeve Series

Patented Vari-Crown tooth form for long coupling life

Comparatively simple installation

All steel sleeves and hubs (stainless steel available)

Precision cut 20 pressure angle gear teeth with minimum backlash

Designs for applications requiring horizontal and vertical orientation

Most standard configurations are available as stock items

Most standard configurations are available as stock items

Angular misalignment of 1/2 per gear mesh (flex-plane)

Angular misalignment of 1-1/2 per gear mesh (flex-plane) up to size 5.5,

Sizes 7/8 through 12, to accommodate bore sizes up to and including

Coupling sizes available through size 30 to accommodate bore sizes up

Load Capacities range from 2,500 in-lbs up to 2,520,000 in-lbs

Interference fit (standard) and Clearance fit on bores are available

Designs for applications requiring horizontal and vertical orientation,

Exposed bolts standard on all sizes, shrouded available by request up

Load capacities range from 7,600 in-lbs up to 47,269,000 in-lbs

Patented and tested BUNA N seal design with reinforced washers

Flanged sleeve couplings are interchangeable with industry standards

Reinforced rubber seals with snap rings to hold in lubricant

Piloted gear fit for higher speeds and less vibration

Labyrinth all steel seal design in FL series

Standard bolts supplied by Lovejoy are treated to be corrosion resistant

Inch and Metric bore sizes available

Inch and Metric bore sizes available

Standard Types and Sizes

Misalignment and End-Float Capability

Lovejoy / Sier-Bath couplings are stocked in an assortment of configurations

The basic principle of Lovejoy / Sier-Bath C and F type couplings is similar

No internal frictional loss or heat buildup

Dentex / Dentex FL - The Flexible Coupling

Operationally, the coupling offers a minimum backlash solution that will

Low profile compact design is easy to implement

Section Pages G-16 and G-17

Single (flex-rigid) or double (flex-flex) engagement

Mill Motor CMM Type

Available with longer universal hubs on both ends

Floating Shaft CFS Type

Spacer CSPCR Type

Cut-out Shifter CCS Type

Shifting mechanisms available upon request

Shear Pin CSHP Type

Easy to install new pins

Section Pages G-34 and G-35

Section Pages G-58 and G-59

FHD Type standard for sizes 10 through 30 (other sizes available

Rigid-Rigid FRR Type

Mill Motor FMM Type

Second hub bored to customer specifications

Section Pages G-46, G-47,

Standard design accommodates AISE Mill Motor frame sizes

Floating Shaft FFS Type

Accommodate longer shaft separations

Rigid hubs inboard (on floating shaft) available upon request

Spacer FSPCR Type