Safe Handling of Bitumen

Safety is No Accident
Observe, think and act
Safe Handling of Bitumen

A PRACTICAL GUIDE
2012 Nynas AB
Designed and produced by Hesketh Design Limited, UK
v1 2012
Nynas Policy for Health Safety Security Environment &

Quality (HSSE&Q)
We want to be the preferred long term supplier of high performance specialty oil products
and services, meeting and, where possible, exceeding the expectations of our customers.
We assess the health, safety and environmental impact of our products and do our utmost to
minimise it. We provide guidance for safe use of our products.
We comply with both applicable regulatory and internal requirements as documented
in our management system. We constantly strive to improve the HSSE&Q performance
by minimising the risk of major and minor accidents, the risk to peoples health and the
environment as well as optimising the efficiency of our activities and use of resources.
We promote a strong and positive HSSE&Q culture, where the line management are
responsible. All employees are individually aware and responsible for their working activities.
We operate a fully integrated and certified management system which meets the
requirements of ISO 9001 and for our technical and operational sites also meets the
requirements of ISO 14001 and OHSAS 18001. Our system provides a framework for
establishing and reviewing HSSE&Q objectives and targets and to continuously evaluate and
improve the effectiveness of the management system.
The aim of the Policy is to support Nynas vision and deliver a performance we all can be
proud of, so that confidence can be earned of customers, employees, shareholders, suppliers,
authorities, neighbours and society at large.
Staffan Lennstrm
President Nynas AB
v1 2012
About Nynas
Nynas is a different kind of oil company.

We use oil to create value and more
sustainable options. Within our field of
specialisation we are a world leader.
With over eighty years experience, we are
one of Europe's leading suppliers of bitumen.
We continue to develop bitumen and its
functional performance in a wide variety of
applications. Our long standing focus on
bitumen has earned us the reputation of
being the bitumen specialist - and that is
something we are very proud of.
We are recognised as a reliable supplier of
specific quality bitumen to meet our
customers changing needs and performance
requirements.
We have refineries and a network of
terminals across Europe. Operating as a
coordinated European company we are
geared to meet each customers local or
regional needs as well as pan European
requirements.
By controlling each step of the supply chain shipping crude oil, refining and final product
dispatch - we are able to provide consistent
products with assured performance.
Our customers often require deliveries on
very short notice at any time of the day or
night, at remote locations. Our customer

driven logistics system and non stop, year
round operations consistently meet these
demanding requirements. This is verified by
our certified ISO 9001 quality management
systems. In addition all Nynas refineries
are certified for ISO 14001 and OHSAS
18001 (environmental and safety & health
management systems respectively).
Nynas provides CE marked bitumen for
paving applications in accordance with the
applicable EN specifications. CE marking is
an EU official confirmation that our products
fulfil the product specifications and the
essential requirements of the Construction
Products Directive.
v1 2012
Contents
Nynas Policy for Health Safety Security

Environment & Quality (HSSE&Q)
The hauliers responsibilities
3.3
Use of hose/flex
3.4
About Nynas
Preface
Loading plan - tank cleaning

- checks
3.5
Sampling bitumen products
3.6
1. Product information

Bitumen - general
1.1
4. Handling and storage
Bitumen composition
1.2
Storage of bitumen
4.1
Types of bitumens
1.3
Oxidation
4.2
Bitumen mixtures
1.4
Mixing
4.3
Product quality
1.5
Tank construction and inspection 4.4
Product information
1.6
Venting pipes and other

attachments
4.5
Bitumen storage tank

requirements
4.6
Cleaning and emptying of tanks
4.7
2. Health, safety and environment

REACH
2.1
Classification Labelling and

Packaging
2.2
Bitumen burns
2.3
Hot bitumen in contact with water 2.4
1. Personal Protective Equipment (PPE)
Exposure to bitumen fumes
2.5
2. ADR regulations
Hydrogen sulphide
2.6
3. Bitumen loading checklist
Skin contact with cutbacks

and emulsions
2.7
5. Eurobitume Bitumen Burns Card
Fire hazard
2.8
Emissions and other

environmental effects
6. Recommended bitumen storage

and handling temperatures
2.9
Spill
2.10
7. Nynas sales offices, depots and

emulsion plants
5. Appendices
4. Bitumen unloading checklist
8. Glossary
3. Distribution, transport,
loading and unloading
9. References
Transport
3.1
Preventing accidents during

handling and transportation
3.2
The suppliers responsibilities
3.3
v1 2012
Preface
Bitumen in its solid phase is not hazardous but due to high temperatures for storage, handling
and transportation there are risks when working with the material. The main aim of this book
therefore is to provide the reader with a clear, useful understanding of bitumen from a product
health and safety perspective so that bitumen can be handled safely within the supply chain.
This creates a good knowledge base and an appreciation of the product and its potential risks.
Nynas HSSE&Q Observe, think and act initiative encourages people to be observant of any
risks, think what should be done to mitigate them and then actually do something about the
situation.
The information in this Safe Handling of Bitumen guide is primarily intended for those who
work operationally with bitumen: road tanker drivers, operating personnel in asphalt works
and bitumen depots, surfacing gangs and other production personnel. Other groups that we
hope will use this publication include safety managers, human resource managers of the above
groups, training coordinators and technicians of all kinds.
The advice given in this publication reflects the current knowledge of the hazards and risks
associated with the handling of bitumen products. If the product is mixed with other materials,
the users shall take these into account when identifying any additional hazards and risks which
might arise.
At the time of printing this safety booklet, the full report of IARC monographs on the
evaluation of occupational exposures to bitumen and bitumen emissions, volume 103 had
not been published. For the latest update on the bitumen industry position, which Nynas is
actively following, please check the Eurobitume website on www.eurobitume.eu/hse. If there
are future industry requirements to make changes in safety recommendations these will be
highlighted in our Nynas Safety Data Sheets, latest versions of which can be found on
www.nynas.com.
Nynas has made great efforts to ensure the reliability of data used in this publication but gives
no guarantees and takes no responsibility, direct or indirect, for damage or loss, nor for any
infraction of applicable international, governmental or local laws, nor for infringement of rights
owned by third party, as a consequence of the use of this publication.
Extracts from this publication may be reproduced without any reformatting except for
commercial purposes.
This booklet and Nynas Safety Data Sheets are available on the Nynas website www.nynas.com
Product information
Product information
v1 2012
Bitumen - general
Bitumen is a non volatile, adhesive and

waterproofing material derived from residue
from selected asphaltene rich crude oil
which is completely or nearly completely
soluble in toluene. It is a viscous and elastic
thermoplastic material, brown to black in
colour and very viscous or nearly solid at
ambient temperatures.
There are many different bitumens and
bitumen products with many different fields
of application in both road construction and
industrial manufacturing. Bitumen is defined
as a construction material according to the
Construction Products Directive (CPD).
Bitumens are, from a regulatory standpoint,
regarded as substances although they
contain a complex mixture of high molecular
weight hydrocarbons.
Bitumen should not be confused with coal
tar which is produced from black coal by
destructive distillation at high temperatures.
Coal tar is completely different in chemical
composition and physical properties and is
classified as carcinogenic while bitumens are
non classified.
Bitumen should not be confused with natural
asphalts which are unrefined products.
1.1
v1 2012
Bitumen composition
Bitumens are very complex mixtures of

high molecular weight hydrocarbons which
also contain small amounts of sulphur,
oxygen and nitrogen. Carbon numbers
are predominantly greater than C25, with
molecular weights varying from 350 up
to about 1500 daltons*. They may also
contain small amounts of various metals
such as nickel, iron and vanadium. The
hydrocarbon skeleton consists of four basic
elements: straight chain alkanes, branched
alkanes, saturated rings (naphthenes) and
fused aromatic rings which are combined in
different size and proportions to make the
large variety of molecules in bitumen.
The several hundred thousand different
molecules in bitumen are continuous with
respect to size and other chemical properties
like for example polarity. All current
knowledge about bitumen chemistry is
based on averages from chemical
characterisation. It has just recently been
possible to identify single bitumen molecules
and determine their basic structure in terms
of size and number of rings but still not the
exact structure.
* dalton (Da) is a unit used to indicate the mass on

an atomic or molecular scale.
1.2
v1 2012
Types of bitumens
There are three main types of bitumens.

Paving bitumens are usually produced
from the atmospheric distillation of
petroleum crude oil followed by further
processing such as vacuum distillation,
thermal conversion, air-rectification or
solvent precipitation. A combination of
these processes can be used for production
of different bitumen grades. Road paving
as the name indicates is the principal use.
Hard bitumens are manufactured in similar
processes to paving bitumens but are harder
and more brittle (with lower penetrations
and higher softening points). The principal
use is in the manufacture of flooring,
bitumen paints, preservation of fibreboard
etc.
Oxidised bitumens (air-blown) are
produced by passing air through a bitumen
feedstock. This gives a product with higher
softening point relative to penetration,
with reduced temperature susceptibility.
The properties of the final bitumen product
depend on the degree of blowing and the
process conditions.
A mild degree of air-blowing, known as
air-rectification, is commonly used to
adjust the physical properties in order to
manufacture substances used in paving.
The penetration index for air-rectified
bitumens is 2.
An intense degree of blowing (oxidation)

is commonly used to adjust the physical
properties in order to manufacture
substances used in industrial applications.
The oxidation process may use flux oil to
soften the feed. A catalyst (phosphoric
acid, ferric chloride etc) may also be used to
increase the speed of the reaction. The main
uses for oxidised bitumen include roofing
material, waterproofing, electrical insulation
and many other building and construction
materials.
The penetration index for severely oxidised
bitumens is >2.
1.3
v1 2012
Bitumen mixtures
Bitumen is also used as a raw material

to manufacture mixtures with improved
handling and application characteristics or to
enhance the physical properties of bitumen.
emulsions may also contain a fluxing agent

and/or a solvent and the bitumen phase
may be a modified bitumen (eg containing
polymer).
Modified bitumens usually contain

polymers or waxes which change their
rheological properties and are used in road
paving, roofing and waterproofing.
In the case of polymer modified bitumens
the desired end performance of the product
influences the selection of the polymer
type. Typical polymers used in the bitumen
industry are elastomeric polymers eg SBS
(Styrene Butadiene Styrene co-polymer).
Bitumen emulsion surface treatment.
Wax modified binders exhibit lower

viscosities at elevated temperatures than
unmodified bitumen. This reduced viscosity
allows end users to either:
reduce mixing temperatures typically by
20C or
maintain conventional mixing

temperatures and improve the workability
and time available for effective

compaction when compared to standard
paving grade bitumen.
In addition wax modified binders are
designed to enhance the performance
characteristics of asphalt at specific phases
within construction and in service lives.
Bitumen emulsions are fine dispersions of
bitumens or modified bitumen in water where
the bitumen commonly is the dispersed phase
and water is the continuous phase.
Bitumen emulsions are normally produced
using a high shear rate mill which disperses
the bitumen in the water. Some bitumen
1.4
Greatly enlarged picture of bitumen emulsion.

Bitumen particles are floating in the water.
The bitumen content of an emulsion

typically varies between 40%-80% and
the application temperature ranges from
ambient to about 90C. A higher content of
bitumen usually leads to a higher application
temperature.
Bitumen emulsions are identified by the
type of electrical charge of the emulsifier.
Three types of emulsifiers are used: anionic
(alkaline), cationic (acidic) and non ionic.
v1 2012
In Europe the cationic emulsions are most

frequently used for bitumen applications.
Cutback bitumens are mixtures of bitumen
with volatile petroleum diluents (kerosene,
white spirit etc) to render them more fluid for
ease of handling and application at ambient
temperature. Depending on the type of
diluent the original properties of the bitumen
may be partly or completely recovered as the
solvent evaporates. Cutbacks are mainly used
in road surface dressings and tack coating.
Fluxed bitumens are mixtures of bitumen
with relatively non volatile flux oils to make
the product softer for ease of application.
The flux oils are commonly high boiling
distillates or process oils which tend to
remain in the binder after application. Fluxed
bitumens are mainly used for very flexible
road pavements in areas with a cold climate.
For all of the above types of bitumen an
adhesion agent is sometimes added to
improve the adhesive performance of the
asphalt mix.
Although there may be other bitumen
mixtures available on the market Nynas only
offers the bitumen and bitumen mixtures
described in this chapter.
1.4
v1 2012
Product quality
The quality and performance of bitumen can

be compromised if it is contaminated by light
oil products during transportation or laying.
If there is any doubt the product should be
retested to check the quality.
Even small amounts of solvent, petrol,
fuel oil or diesel can considerably alter the
properties of bitumen films and lead to
deterioration of their adhesive properties
which in turn may lead to failure of the
asphalt.
Deterioration and softening of asphalt due to

fuel spillage.
It is essential that bitumen is handled and

stored at the correct temperature.
If the temperature is too low, coating of
aggregate will be uneven; whereas if the
temperature is too high, the properties of
the bitumen will deteriorate and it may drain
from the aggregate leading to run off.
The temperature at which bitumen can be
pumped and mixed depends on the grade.
These temperatures are calculated on the
basis of viscosity measurements and are
supported by operational experience.
More information can be found in
Recommended bitumen storage and
handling temperatures, Appendix 6.
1.5
A damaged road that suggests the defects could

be due to a poorly mixed asphalt.
v1 2012
Product information
Nynas offers a wide range of bitumen

products.
Safety Data Sheets, Product Data Sheets and
CE Data Sheets can be found on the Nynas
website www.nynas.com or will be sent
upon request.
For additional information please contact
one of the Nynas regional sales offices.
Contact information is given in Appendix 7.
1.6
Health, safety and

environment
Health, safety and environment
v1 2012
REACH
REACH is the European regulation on

chemicals and their safe use. It stands for
Registration, Evaluation, Authorisation and
Restriction of Chemicals. REACH requires
manufacturers and importers of chemicals
to register the substance(s) to the European
Chemical Agency (ECHA). Depending on
annual tonnage and hazards of the substance
there are different deadlines for when the
registration has to be completed.
As from 30 November 2010 all substances
manufactured or imported above 1000
tonnes/year need to be fully registered.
One major part of the registration dossier is
the Chemical Safety Assessment (CSA) which
must include:
hazard assessment; classification and
labelling of human health, environmental
and physiochemical hazards; Derived
1
No Effect Levels (DNELs) ; Predicted
2
No Effect Concentrations (PNECs)
Persistent, Bioaccumulative and Toxic (PBT)
and very Persistent and very

Bioaccumulative (vPvB) assessment.
If the substance meets the criteria for
classification as dangerous or meets the PBT/
vPvB criteria, the CSA shall also include:
an exposure assessment for all identified
and relevant uses of the substance
including the generation of exposure
scenario(s)
a risk characterisation which identifies if

the risks arising from manufacture/import
and uses of a substance are adequately
controlled.

The risk characterisation consists of a

comparison of DNELs and PNECs with
calculated exposure concentrations
respectively to humans and to the
environment. If the calculated exposure
exceeds the DNEL/PNEC there is a need
to implement risk management measures
(protective clothing, ventilation etc).
European bitumen manufacturers have

recently completed a review of the health
and environmental impacts of bitumen,
required as part of the REACH registration
process. Based on the published data at
that time bitumen is considered unlikely to
present a hazard that requires classification
for human health, safety or the environment.
Animal studies on severely oxidised bitumen
(penetration index >2) indicate that repeated
exposure to fumes may present a weak
carcinogenic hazard. The classification
criteria are not fulfilled but additional risk
management measures are communicated in
the Safety Data Sheets for these products.
Since bitumen is not classified as hazardous
under REACH there is no legal requirement
to make an exposure assessment or a risk
characterisation.
Derived No Effect Level:

the level of exposure above which humans
should not be exposed.
1
Predicted No Effect Concentration:

the concentration of the substance below which
adverse effects in the environmental sphere of
concern are not expected to occur.
2
2.1
v1 2012
Safety Data Sheets

REACH also sets up the obligations for
Safety Data Sheets (SDS). Suppliers are
required to provide their customers with SDS
for all classified substances/mixtures.
The SDS is supposed to be the main channel
for communication down the supply chain
on REACH related information. As a
consequence the information requirements
in the SDS have become more extensive
compared to the previous Safety Data Sheet
Directive.
Examples of new information to be included:
identified uses for the substance uses
which have been identified by supplier
and/or customer and for which use is
regarded as safe
REACH registration number - company
specific number that confirms the
substance has been registered
exposure scenarios for classified
substances should be in an annex
to the SDS covering identified uses
DNEL/PNEC - both DNEL and PNEC are

derived from toxicological and
ecotoxicological studies.
Under REACH, bitumen is not classified as
hazardous and there is currently no legal
requirement to provide SDSs for bitumen.
However SDSs do contain very important
information regarding safe handling of
bitumen and therefore it is industry practice,
which is followed by Nynas, to provide them.
2.1
v1 2012
Classification Labelling and Packaging
Classification Labelling and Packaging (CLP)

is the European version of the UN based
system for classification and labelling Globally
Harmonised System (GHS). CLP introduces
a new system including new criteria for
classifications, new types of indications of
danger, pictograms, hazard statements and
precautionary statements.
As from 1 December 2010 all substances
have to be classified according to the
regulation on CLP, EC 1272/2008.
For mixtures there is a transition period for
classification according to CLP until 2015.
Bitumen is not classified as hazardous
according to the CLP regulation.
Bitumen mixtures that contain solvents,
flux, emulsifiers and other additives may be
classified as dangerous to health and/or to
the environment. The classification of these
mixtures is specific since they depend on the
classifications and amount of the different
ingredients. Therefore it is important to check
the SDS.
2.2
v1 2012
Bitumen burns
Bitumen is normally manufactured, stored,

transported and handled hot. Hence the
most significant hazard is the potential to
cause severe burns.
There are several cases where there is a risk
of personnel being covered with hot bitumen
for example:
if a hose bursts
boil-over of a truck or storage tank
if a valve has been blocked and the plug
is released
sampling without correct Personal
Protective Equipment (PPE) or experience
of how to open the valve.
To minimise the risk of burns it is essential
to always wear PPE and to follow proper
working procedures. The required PPE is
shown in Appendix 1. It is recommended
to have a safety shower in the vicinity
(20m radius) of the loading/unloading areas.
For first aid in case of burns

After an accident has occurred the affected
area of the body should be cooled as soon
as possible to prevent the heat from causing
further damage to the skin. The burn
should be drenched in cold water for at
least ten minutes for skin burns and at least
five minutes for eye burns. However body
hypothermia must be avoided.
Never attempt to remove bitumen from
burned areas!
The bitumen layer will be firmly attached
to the skin and removal should not be
attempted unless carried out at a medical
facility under the supervision of a doctor.
The cold bitumen will form a waterproof
sterile layer over the burn which will prevent
the burn from drying out. If the bitumen
is removed from the wound there is the
possibility that the skin will be damaged
further, bringing with it the possibility of
complications.
Furthermore, by exposing a second degree
burn in order to treat it, there is the
possibility that infection or drying out will
make the wound deeper.
Contact with hot bitumen causes severe

burns on exposed skin.
2.3
Eurobitume has published a

recommendations card about burns that
is easy to read and suitable to hang up at
the work site. The Bitumen Burns Card
is available in several languages and can
be ordered from Eurobitume or via Nynas.
A copy of this is illustrated in Appendix 5
(showing the version available at time of
print).
v1 2012
Hot bitumen in contact with water
If water comes into contact with hot

bitumen there is a risk of a violent reaction.
In contact with hot bitumen the water
evaporates and expands in volume which
leads to splattering. In a storage tank or
truck the pressure can increase and result in
a violent eruption of hot bitumen. If closed,
the truck or tank could explode or rupture.
As a consequence it is of utmost importance
to ensure that tanks and trucks are free
from water. See 3.2, 3.5 and 4.1 for more
information.
Still from CCTV footage of an eruption of

bitumen from a tanker.
Examples of risks of boil-over:

previous load of bitumen emulsion or
any product with high water content
cold truck (water condensation/mist)
trapped water in storage tank.
The most common reason for boiling over
is hot bitumen being loaded in a tank that
has previously contained bitumen emulsion.
The water in the emulsion vaporises and
expands. The pressure will increase and
eventually become so high that the steam
will push the bitumen through the manhole.
If the tank is closed the increase of pressure
can cause an explosion.
2.4
v1 2012
Exposure to bitumen fumes
Heated bitumen emits fume consisting of a

gas phase and an aerosol phase. The gas
phase is often called the semi volatile phase
while the aerosol phase is called blue
smoke. Bitumen fumes are not considered
harmful to the public. Exposure to high
concentrations when handling hot bitumen
can cause irritation of the eyes and nose and/
or respiratory tract.
The Derived No Effect Level (DNEL) which

has been derived in the REACH process is
2.9mg/m3 (Total Hydrocarbon Concentration,
TWA* 8h) for bitumen based on irritative
effects.
Working at the correct temperature and

using the correct bitumen products for each
specific application can reduce the fuming of
bitumen during normal handling.
Exposure measurements at paving works

have shown that the light oil molecules
which are present in inhaled air largely come
from solvents such as diesel oil which was
historically used as a release and cleaning
agent when applying the bitumen.
It is recommended to strive for a good

working environment where all unnecessary
exposure is avoided. In certain applications,
for example indoor mastic asphalt works (in
tunnels, buildings or multi storey car parks),
the exposure level can be high.
In these cases adequate ventilation must be
provided (eg tunnel fans) and it is essential to
use the recommended protective equipment.
Due to the presence of solvent, cutbacks
may cause dizziness or nausea when
used in confined spaces. Again in these
circumstances adequate ventilation is always
recommended.
There is no EU occupational exposure limit
(OEL) set for bitumen fumes but several
European countries have established their
own threshold value and/or short term
exposure limit. Please note that these values
are country specific. For more detailed
information please refer to section 8 of the
Safety Data Sheets.
*Time Weighted Average
2.5
For more information on workplace exposure

measurement protocol see
www.eurobitume.eu
Bitumen contains a small amount of

Polycyclic Aromatic Hydrocarbons (PAHs) of
which some are classified as carcinogenic.
As a consequence there have been many
studies to evaluate if there is an increased
risk of cancer among asphalt workers. The
International Agency on Research on Cancer
(IARC) has done an epidemiological study
on asphalt workers in several European
countries. This study showed a small increase
of lung cancer among asphalt workers in
some countries but it was not possible to
see if the cancer was related to bitumen or
other factors (eg tobacco smoking). As a
follow up IARC conducted a study where the
reasons behind the cancers were evaluated.
The outcome of this study showed that there
was no direct link between bitumen and
lung cancer. The increase was probably more
linked to tobacco smoking.
At the time of printing this safety booklet
the full report of IARC monographs on the
evaluation of occupational exposures to
bitumen and bitumen emissions, volume
103, had not been published.
v1 2012
Bitumen fume
BITUMEN FUMING AS A FUNCTION OF HANDLING TEMPERATURE
150
170
190
210
230
250
Temperature
Soft grade bitumen
Hard grade bitumen
For further details on the monograph
conclusions and latest bitumen industry
updates please check Eurobitumes website:
www.eurobitume.eu/hse or Nynas website
www.nynas.com
Although there is no currently available study
showing that even long term exposure to
bitumen fumes is harmful, it is nevertheless
recommended to avoid all unnecessary
exposure.
The following should be noted:
control temperature to reduce fuming
do not use diesel fuel as a release and
cleaning agent.
2.5
v1 2012
Hydrogen sulphide (H2S)
The release of H2S from both crude oil

and certain types of oil products such as
heated bitumen is and has been a common
occurrence in the petroleum industry.
Hydrogen sulphide (CAS # 7783-064,
EINECS # 231-977-3) is a toxic and
flammable gas which is heavier than air
and may accumulate in low areas and
confined spaces. It is characterised by a
strong odour of rotten eggs at low
concentrations. But this odour cannot be
relied upon to warn of the presence of
dangerous concentrations because the gas
rapidly deadens the sense of smell even
at concentrations below hazardous levels.
When handled hot, bitumen odour will also
camouflage the rotten egg odour of H2S.
The principal symptoms of exposure to H2S

are irritation of the eyes, nausea, vomiting,
dizziness and headaches. Prolonged exposure
to concentrations above 50ppm produces
irritation of eyes, nose, throat and lungs. Any
exposure to concentrations above 500ppm
can be fatal. Levels above 700ppm cause
unconsciousness and a person can collapse
within seconds.
In open working areas hydrogen sulphide
is unlikely to pose a risk to health. However
hydrogen sulphide can accumulate in closed
spaces and in the headspace of storage
tanks containing bitumen and can reach
potentially hazardous concentrations (lethal
concentrations may occur).
There is also a risk of potential hazardous
concentrations in headspace of trucks and in
storage tanks further down the supply chain
(asphalt plants etc).
At many loading sites the driver

has to stand here during loading
Inside tanker manlid < 50ppm
1.5m 1ppm
1.0m 3ppm
0.5m 5ppm
Truck tank headspace < 500ppm
Note: figures obtained from Nynas H2S

monitoring measurements 2010/11
2.6
v1 2012
Areas around manlids and ventilation pipes

are risk areas for exposure especially during
filling operations.
There are national Occupational Exposure

Limits (OEL) for hydrogen sulphide. The
values can be found in the Safety Data Sheets
for bitumen.
Access to vents should be restricted with

warning signs for H2S and access prohibited
while the tanks are being filled.
First aid in case of hydrogen sulphide

intoxication or excessive fume exposure
When access is necessary, as for manual tank

measurements, a full gas mask should be
worn.
At loading sites there should be signs that
warn the loader of possible H2S. Personal
Dose Monitors (PDM) are recommended for
those performing the loading.
Before entering confined vapour spaces in
bitumen tanks always check for hydrogen
sulphide.
Tank breather/vent
(signage)
Under safe conditions, remove the person

from the contaminated atmosphere into fresh
air. Rescuers must wear breathing apparatus,
belt and safety rope and follow rescue
procedures. If trained to do so immediately
begin artificial respiration if breathing has
ceased. Provision of oxygen may help. Obtain
medical advice for further treatment. If the
gas has affected the eyes, wash with water
for at least five minutes and seek medical
attention.
Top manlid < 50ppm
Overflow/vent pipework
(signage)
1.5m above manlid 1ppm
Tank headspace < 500ppm

Tank bottom manholes

(signage)
Fume release
(signage)
Note: figures obtained from Nynas H2S

monitoring measurements 2010/11
Bitumen discharge
connection
Bitumen fume
2.6
v1 2012
Skin contact with cutbacks and emulsions
Cutbacks contain a solvent (eg naphtha,

kerosene, white spirit or flux oil) which
depending on the type of solvent may cause
skin irritation at repeated exposure.
Where contact with the skin is repeated over
a long time there is a risk - although a small
one - of permanent skin damage.
Bitumen contains very low concentrations of
Polycyclic Aromatic Hydrocarbons (PAHs) of
which some are known to be carcinogenic.
The concentration of PAHs is lower in
bitumen than in the crude oil itself since
the production process includes a vacuum
distillation step where practically all the PAHs
are lifted out.
In undiluted bitumen the PAHs are not
considered to be bioavailable. However if the
bitumen is mixed with diluents it is believed
that such materials may become bioavailable
if the product has low viscosity at ambient
temperatures.
Bitumen emulsions contain low
concentrations of emulsifiers which can cause
irritation to the skin and eyes. Some of the
emulsions can also contain small amounts of
solvents.
It is therefore essential to wash carefully
the parts of the body that have come into
contact with a bituminous mixture with
soap and water or a vegetable oil. It is
recommended to use an appropriate skin
cream afterwards.
Always check the appropriate Safety Data
Sheet for more information.
2.7
v1 2012
Fire hazard
Danger of fire and explosion

In order to prevent fire in storage tanks the
product should be stored sufficiently below
its ignition temperature. This provides a
safe margin for deviations of any measuring
devices. Bitumen should be stored at least
30C under its flash point. The auto ignition
temperature for pure bitumen is over 300C.
There is a risk of self ignition if bitumen
has leaked into tank insulation. Heating
that leads to self ignition on the surface of
porous or fibrous material that has been
impregnated with bitumen or by condensed
bitumen fume can occur at temperatures
below 100C.
Carbon deposits that can be pyrophoric
may develop on walls and roofs of bitumen
storage tanks. In the presence of oxygen,
these might develop a risk of self ignition.
Actions to prevent fire and explosions

Clean and repair any damaged insulation.
Replace the insulation where it has been
contaminated. If there has been a storage
tank overfill it is very likely that this will
lead to a fire in the insulation unless correct
actions are taken. If contaminated, insulation
cannot be immediately replaced the risk of
fire could be decreased by injecting steam
through the use of steam lances.
Tank insulation that has been impregnated

with bitumen should be replaced.
during or soon after unloading. However

road tankers and railway wagons can be
equipped with heating tubes for heating
bitumen with bottled gas. It is essential that
heating tubes in a tank are well covered by
bitumen (between 10cm and 20cm) during
the heating process. This especially applies
to cutbacks that contain solvent with a low
flash point. The heating tubes should have
a double skin to avoid local overheating.
Flames must never directly heat the tank
surface. If this happens there will be a risk
of ignition. Ensure that protective tubing
is in good condition. A common cause of
bitumen ignition is localised overheating
during the heating process, for instance
during unloading.
Bitumen road tankers and storage tanks

that have contained cutbacks may contain
concentrations of flammable vapours in the
headspace. Therefore no open flame such
as that of a bottled gas burner, blow torch
or similar should be in the immediate vicinity
2.8
v1 2012
Bitumen fires can be very violent.
Fire in a tank is fought with dry powder extinguishers.
Extinguishing bitumen fires

NEVER USE A WATER JET!
Bitumen fires must be extinguished by
smothering so that the continued supply of
oxygen can be prevented.
Small fires can be put out with a blanket
of foam, dry powder or carbon dioxide
extinguishers.
Large fires are extinguished preferably by
using foam or dry powder extinguishers but
there is a danger of fires flaring up again.
Foam and powder do not provide a lasting
oxygen free atmosphere in bitumen fires.
2.8
Fires in tank insulation can be put out using

steam from a spray unit or a dry powder
extinguisher. It is essential to always replace
contaminated insulation. If it is not replaced
the fire could ignite again when oxygen is
reintroduced unless the temperature is well
below 100oC. Ensure that workplaces and
road tankers are equipped with extinguishers
of the correct size and type.
If a bitumen fire arises, always call the local
emergency fire services and tell them what is
on fire.
v1 2012
Emissions and other environmental effects
Bitumen as such is not classified as dangerous

to the environment.
REACH requires assessment of the Persistent
Bioaccumulative Toxic (PBT) and Very
Persistent Very Bioaccumulative (vPvB)
properties of a substance. Bitumens are
neither classified as PBT or vPvB.
Bitumen is a hydrocarbon UVCB (substances
of Unknown or Variable composition,
Complex reaction products or Biological
materials) that does not pose a chronic
hazard to water, soil or sediment. Derivation
of PNEC (Predicted No Effect Concentation)
for bitumen is not scientifically justified due
to limitations on water solubility.
Some components used in bitumen mixtures
are classified as environmentally hazardous.
For example bitumen cutbacks normally
contain solvents that are classified as
dangerous to the environment. Depending
on the type of ingredients used, some of
the bitumen emulsions are also classified
as harmful or toxic to aquatic organisms.
The severeness of the classification depends
on the classifications and amounts of the
ingredients. Always check the Safety Data
Sheet.
2.9
v1 2012
Spill
Bitumen
Spillage of bitumen to ground is relatively
harmless. Leaks and spillages will initially
consist of molten hot material and there may
be a risk of severe burns. The bitumen will
cool down and become solid. The affected
area can be cleaned up using ordinary
equipment such as spades, rakes, wheel
mounted loaders and similar.
In water, bitumen will normally sink into the
sediment at the bottom although in some
circumstances it may float.
The main effect of a spill of bitumen in
water or on soil is adsorption to sediment
causing physical contamination. The water
solubility of bitumen is so low that it could be
considered to be negligible. Bitumens are not
thought to present any significant hazard to
the aquatic environment.
Bitumen constituents are potentially
bioaccumulative but the low water
solubility and high molecular weight make
the bioavailability to aquatic organisms
limited. Bioaccumulation is unlikely. The use
of bitumen in road and roofing construction
shows that bitumen is a persistent material
(ie it is not and should not be biodegradable).
Cutbacks
Cutback spillage to ground can be more
complicated since it has a lower viscosity and
can consequently penetrate the soil and/or
affect nearby watercourses before hardening.
In time the solvent will evaporate from the
product.
2.10
Surface dressing bitumen cutbacks are being

replaced by bitumen emulsions.
If spilled in water the product will form a film

on the surface and spread. The product will
adhere to soil and the solvent will evaporate
from the product. The bitumen itself is
immobile and will remain on the soil surface
where it can be removed mechanically.
Bitumen emulsions
In contact with soil the emulsion will break
and the bitumen particulates are adsorbed
in the upper layer and are therefore easy to
clean up.
In contact with water, the emulsion will
spread out on the surface of water and blend
with the water. The emulsion will finally
collapse on dilution. The emulsifier will partly
dissolve in water and the bitumen phase will
disperse.
v1 2012
Actions and advice in case of a spill

Even though most bitumen products are
not hazardous to the environment they can
cause physical contamination.
A major bitumen spill can for example block
sewers and drains when hardening. For this
reason any spill should be controlled as soon
as possible without endangering peoples
health in the process.
Prevent product from entering sewers, rivers
or other bodies of water since the solidified
product may clog drains and sewers.
Guidance on spillage:
small spill - allow the bitumen to cool
and solidify. Remove mechanically into
containers for disposal or reclamation in
accordance with local regulations
large spill - prevent from spreading by
making a trench or barrier with sand,
earth or other material. Otherwise treat
as a small spillage.
Contact the local authorities and/or
emergency services. Always act according to
the local legislation.
Bitumen residue from cleaning a filter.
Atmospheric emissions
Bitumen at ambient temperature does
not cause any atmospheric emissions.
However storage and application at elevated
temperatures cause diffuse emissions of
mainly hydrocarbons. These emissions
increase with the handling and storage
temperature.
When bitumen is heated, hydrogen sulphide
is given off as well as hydrocarbons. For
more information regarding hydrogen
sulphide please see 2.6.
Waste disposal
For the disposal of bitumen products, refer to
section 13 of the Nynas Safety Data Sheets.
Bitumen itself is not regarded as a hazardous
waste.
2.10
Distribution, transport
Distribution, transport,
v1 2012
Transport
The majority of bitumen products are

transported in bulk by road tankers or
vessels. In some countries rail transport is also
used. Smaller volumes can also be supplied
in drums or mini containers for example
intermediate bulk containers. This is common
practice for emulsions and bituminous
solutions but less common for road bitumen.
Oxidised bitumen and polymer modified
bitumen can also be distributed in pellets or
in blocks, stacked on pallets.
Modern Nynas tanker used for bitumen transport.
Transporting hot bitumen is subject to the

international UN regulation regarding the
transportation of hazardous goods which
applies to:
road transport (ADR)
rail transport (RID)
inland waterways transport (ADN)
sea transport (IMDG).
Road transportation of dangerous goods
in Europe is regulated by the international
agreement Accord Europen relatif au
transport international des marchandises
Dangereuses par Route (ADR). This regulation
implies specific requirements regarding for
example:
the vehicle
labelling of the vehicle (with respect to
the goods being transported)
checking documentation and emergency
information relative to the product
the driver (and co-driver).
For details of ADR refer to Appendix 2.
For the transport of bitumen products refer to
section 14 of the Nynas Safety Data Sheets.
3.1
v1 2012
Preventing accidents during handling and transportation
All equipment and its maintenance

should always follow local, national and
international regulations and codes of
good practice.
During loading of Bitumen

It is important that the tanker does not
contain residues from previous loads, for
example emulsion or a product with a low
boiling point. Bitumen loaded onto water or
emulsion can lead to a violent eruption or
boil-over. It must therefore be avoided at all
times.
Tanks that have carried emulsions have to
be steam cleaned and dried before they can
be used for bitumen products. Procedure
loading must be considered.
If a dead mans handle is to be used during
loading, it is strictly forbidden to override the
operation of the safety handle.
There is a risk of splashing especially
when loading commences. Always use the
correct Personal Protective Equipment
(see Appendix 1).
In the event of an accident the depot
or refinery personnel should always be
contacted and the local site instructions
followed.
Safe bitumen delivery in brief

Use all round Safety Awareness Observe, think and act.
Be aware of the vehicles emergency
locations (fire extinguishers, emergency
stop buttons, main closure valve).
Ensure all personnel are kept at least
6m away from the delivery operation
(exclusion zone).
Driver must stay in attendance at the main
closure valve at all times during delivery.
Check and secure any valves, caps, covers
and padlocks.
Leave the delivery point in a clean
condition.
Sign and complete delivery
documentation.
Report all defects or any problems firstly
to the customer, secondly to your Nynas
contact.
3.2
v1 2012
The suppliers responsibilities

The supplier/consignor is responsible for:
classification of the products under
ADR, RID, ADN and IMDG
using approved packaging for packaged
products ensuring correct marking and
labelling
declaring products in accordance with local
regulations
Information regarding the classification of

each product is given in the Safety Data
Sheets provided by the supplier.
Nynas can provide on request Additional
Information for ADR 5.4.3 Instructions in
Writing. Please see an example in
Appendix 2.
issuing the correct transportation

documents to accompany the delivery.
The hauliers responsibilities
In order to guarantee the correct delivery

it must be ensured that the right product
and quantity at the right temperature is
loaded on the premises of the bitumen
supplier. This should be verified throughout
the entire process.
The temperature of the load can fall
quickly if the vehicles tanks are cold.
Recommended handling temperatures are
given in Appendix 6.
The haulier guarantees that vehicle tanks
are approved for transport according to the
Nynas instructions. The driver must inform
the supplier about the previous load. The
supplier is entitled to verify this information
at any time.
Drivers who transport ADR classified

goods require a special training certificate.
The haulier is responsible for the training
and certification of its drivers.
Accredited bitumen suppliers normally have
equipment and checking procedures so that
the driver can easily monitor the loading
process. If anything goes wrong the driver
should always immediately stop loading and
contact the bitumen suppliers personnel.
The haulier/driver should use the suppliers
accident/incident reporting system as well
as the one used in his own organisation
in order to take preventive and corrective
actions as soon as possible.
It is the hauliers responsibility to:

make sure that vehicles are fully equipped
according to the ADR legislation and that
they are properly marked and labelled
provide their driver/s with ADR Instructions
in Writing 5.4.3.
3.3
v1 2012
Use of hose/flex
The delivery hose/flex is a vital piece of

equipment for the safe delivery of elevated
temperature products. It is therefore very
important to use the correct hose/flex for
the intended use.
It is recommended that the hose should
have a minimum length of four metres.
Importantly for elevated temperature
products the hose/flex must have
temperature rating and a pressure rating.
Testing of the hose/flex should be carried
out according to local legislation and codes
of good practice. It is recommended to test
them at least annually. This will include
equipment certification. Records of the
testing should be kept by the owner.
Hoses that have not been tested should
not be used.
Drivers should carry out checks on their hose/
flex, connection packings and gaskets before
use on a daily basis. If any faults are found
defective equipment should not be used and
corrective actions should be taken.
3.4
v1 2012
Loading plan - tank cleaning - checks
To minimise the risk of accidents and to ensure

a high quality standard of delivered products
it is very important that a vehicles tank does
not contain residue from previous loads.
Special attention should be paid to emulsions
(containing water) and products with a low
flash point. In case of doubt the bitumen
supplier/depot manager should always be
consulted.
Due to the dangers of mixing bitumen
emulsion and bitumen it is recommended that
inspection of the loading vehicle is instigated
and site specific procedure loading is followed.
Always consult with the bitumen loading
facility.
More information regarding safe loading is
described under Preventing accidents during
handling and transportation, 3.2. Loading and
unloading checklists are added as Appendices
3 and 4.
3.5
v1 2012
Sampling bitumen products
Hot bitumen sampling is particularly

hazardous due to the risk of splashes and
spills that can cause burns. It is therefore
essential to wear the appropriate Personal
Protective Equipment (PPE) as indicated in
Appendix 1.
The sampling area should have safe ingress
and egress with adequate lighting.
Local site specific instructions must always
be followed. If in doubt, ask the site
representative.
Bitumen sampling point.
In line sampling valves
Labelling of samples
In this case sampling valves are placed in the

pipe and are used to take a sample directly
from the bitumen flow.
Always fill in the label on the sample

container with the following information:
date of sampling
delivery depot/place of sampling
Dip sampling
delivery note number

receiving tank
Dip sampling is used for small samples using

a weighted receptacle attached to a rope or
rod. Sample taking from road vehicles should
be avoided. There is a risk of exposure to
potentially hazardous concentrations of H2S
during dip sampling (please see section 2.6).
Dip sampling of cutbacks should be avoided
due to the flammable atmosphere in the
tankers vapour space.
3.6
samplers signature.
Handling and storage
Handling and storage
v1 2012
Storage of bitumen
All bitumen products should to a certain

extent be regarded as perishable goods as
their characteristics change when stored
for long periods at varying temperatures.
This applies especially for packaged liquid
bitumen products which therefore can only
be stored for a limited period.
Correct storage temperature of bitumen
products will guarantee product quality in the
final application. From a quality perspective
it is therefore essential that the product is
handled correctly. Bitumen is a construction
material and should be handled accordingly.
Bitumen should be stored in well insulated
tanks. This will reduce the need for extra
heating which in turn will reduce heating
costs. The temperature of the heating source
can also be kept lower so that the bitumen
will not be unnecessarily exposed to excessive
contact temperatures. Please note that
bitumen at the bottom of a storage tank can
have a considerably higher temperature than
in other parts of the tank unless it is properly
agitated.
If the bitumen is overheated locally, deposits
may be produced. These deposits appear on
heating coils and other inner parts of storage
tanks. After a while such deposits may fall
off and interfere with pumping or mixing
actions.
Care should be exercised to ensure that the

temperature at the bottom of an empty tank
does not become so low so as to allow water
to condensate.
An empty cold tank should initially be filled
up gradually. This will give any remaining
moisture time to evaporate. For tanks
containing cold bitumen, heating should be
carried out at a low level until the bitumen
temperature has reached 120C. This enables
moisture to evaporate before hot bitumen
is added to the tank. It is important that
bitumen covers the heating tubes when
heated.
It is recommended to fill tanks in three
stages allowing the temperature in the tank
to equilibrate each time one third has been
loaded.
Packaged bitumen for example in drums
is not as likely to be affected by oil or
contaminants as is bitumen in bulk.
Nevertheless packaged bitumen should be
stored carefully. The warmth of the sun can
cause the light components in the product
to vaporise and form bubbles when the
packaging is damaged. These bubbles can
contain flammable vapours.
For the selection of a products storage

temperature please refer to the bitumen
handling temperature recommendations
given in Appendix 6. In the case of specialty
products please refer to manufacturers
recommendations.
4.1
v1 2012
Oxidation
The characteristics of bitumen products can

change when stored for prolonged periods
at high temperatures. Bitumen will gradually
harden. The penetration, a measure of the
bitumens hardness, may decrease. The
hardening process will increase when higher
storage temperatures are used and will be
worse in partly full tanks where more air is
present.
There is a possibility that flammable
atmospheres can be generated. Pyrophoric
deposits can also be formed. For this reason
controlled oxygen depletion is recommended.
Continuous purging of the tank vapour space
is not recommended because it can promote
the formation of pyrophoric deposits. Oxygen
concentrations between 4% and 6% are
normally sufficient to prevent the build up of
deposits.
If the tank has been operated under
controlled oxygen depletion then any
potentially flammable vapours should be
displaced for example with nitrogen before
air is allowed to enter the tank (ie cooling
before maintenance).
4.2
v1 2012
Mixing
In some cases it is necessary to blend

different grades of bitumen. Such blends
seldom become homogeneous if they are
not stirred mechanically or blended through
an in line blender. Mixing by means of air is
not advisable for bitumen products since this
will result in an oxidation process. The mixers
should be activated occasionally in order to
maintain the proper temperature and quality
of a tanks contents.
Electric driven agitator side mounted on a
bitumen storage tank.
4.3
v1 2012
Tank construction and inspection
Construction, equipment and inspection

of storage tanks for oil products in general
should follow the API standards 650 and 653
regarding Welded steel tanks for oil storage
and Tank inspection, repair, alteration and
reconstruction and/or any additional local
standards such as the latest Bitumen Safety
Code (model code of safety practice)
provided by the Energy Institute.
For bitumen product tankage inspection by
an independent inspection company is not
necessary. Inspection can be handled locally
in a self administered programme.
It is recommended that new tanks are
inspected after 20 years. Tanks older than
20 years should be inspected every 12 years.
Inspection can be more frequent if any
reasons are seen for this, for instance if tank
corrosion is begun to be noticed and the
tank needs to be monitored more closely.
This evaluation can be done by expertise at
the location or in cooperation with Nynas.
A bitumen tank should also be provided
with an inert gas blanketing system to
prevent tank breath (moisture and oxygen
getting into the tank). API 2023 gives
recommendation on when bitumen tanks
shall be inerted.
It is recommended to have a safety shower in
the vicinity of storage tanks in which bitumen
is being unloaded.
In respect of tank entry please refer to 4.7.
4.4
v1 2012
Venting pipes and other attachments
Pipework should comply with local

regulations and standards and should be
as vertical, as short and with as few bends
as possible. If the pipework is required to
be longer than necessary or is in exposed
locations then insulation and heating of the
pipework will be required. The inlet should
be between 0.5m and one metre from
ground level and be fitted with a specialist
flange fitting.
If the line is full and the inlet line is lower
than the bitumen level then syphoning will
take place.
Damage to tanks pipework and equipment

can be prevented through regular inspection
and an adequate preventive maintenance
programme.
Special attention should be paid to the
inlets through the insulation because pitting
may occur there. Bitumen leakage and
condensation of oil mist between the tank
plate and insulation is a frequent cause of
fire. It is important to replace contaminated
insulation as soon as possible!
It is recommended to have independent low,

high and ultra high level alarms installed on
bitumen storage tanks.
Ventilation from the headspace of tanks
should be placed to minimise personal
exposure of hydrocarbon and H2S to the
tank headspace.
Bitumen and bituminous solutions are stable
substances that do not tend to corrode metal
surfaces they contact. However vapours
from the tanks vapour space constantly
move in and out through the vent pipes at
storage depending for instance on weather
conditions. The tank breathes which causes
a continual mixing of air, moisture and
hydrocarbons. This mixture is corrosive.
Coke deposit can also be formed in vent
pipes and cause a harmful over - or under
- pressure inside the tank. This applies
especially to tanks containing oxidised
bitumen. Storage tanks for bitumen
emulsions are normally not affected by
the product.
4.5
v1 2012
Bitumen storage tank requirements
Ladder
Vent
Measuring electronics
- High level alarm
- Level gauge
- Temperature gauge
Handrail and
stairs
Shell plates
Wind girder
Strong winds
can tear down
the shell plates
Choose the right

construction steel
Must be easy to replace
Overflow
pipe
Heating coils
Must be easily accessible
for maintenance
Manlid
Stirrer
Consider the placing for

ease of tank maintenance
Consider power
requirement
and mechanical
stability
Insulation
- Suitable for temperatures
up to 230C
- Good insulation limits
temperature variations in the tank
- Limits deposits
Sloping bottom plate

Easier to empty the tank
4.6
Decontamination
Cleaning
hatch
Valves
- Draining
- Inlet
- Outlet
- Sampling
Gravel or smooth
concrete base on
the area around the
storage tank - for
easier waste handling
v1 2012
Cleaning and emptying of tanks EU Directive

UK Confined Space Entry Regulations
Bitumen deposits created by the oxidation

process can often be found in storage
tanks with a high storage temperature or
uneven temperature distribution. Therefore
tank cleaning should be part of a regular
maintenance programme taking into account
the tanks history and the applicable local
legislation.
When emptying a storage tank it is essential
to be familiar with the layout of the bottom
of the bitumen tank; the way in which the
heating coils are constructed; and how
conduits are connected.
The tank is normally heated to the highest
temperature the product allows for storage
before the content is pumped out. Draining
of the final section should be done slowly to
allow the bitumen sufficient time to flow and
prevent tank implosion.
When a tank is taken out of service always
ensure that the tanks temperature is below
40C before opening the manhole for
ventilation. When the tank has more than one
manhole, the lower one should be opened
first.
Before personnel can enter the tank, the tank
should be ventilated and gas tests should
be performed in order to guarantee a safe
work environment (with safety permit system/
checklist for work in confined spaces in place).
Cleaning activities inside a storage tank.
Tanks for soft bitumen, bituminous solutions

and bitumen emulsions can normally be
cleaned through successive mixing of the
residue with solvent. However care must be
taken to ensure that the temperature is always
kept below the flash point of the mixture.
Whenever products are changed in large
installations the pipework must be emptied.
This can be done by flushing in several stages
which will ensure that only traces of the
previous product will remain in the piping
system.
Bitumen residue that cannot be pumped out or

washed out with oil while it is warm is usually
allowed to solidify and must be chiselled away.
Product remnants should be disposed of in
compliance with local and national regulations.
Recycling is always recommended.
4.7
Appendices
Appendices
One
v1 2012
Appendix 1 - Personal Protective Equipment (PPE)

11
For all tasks involving bitumen handling,
a task Risk Assessment should be
performed detailing the required PPE
for the associated task.
2
3
PPE should be used when working with

bitumen and should cover all parts of
exposed skin to avoid direct contact.
1. Loading and unloading
Always use:
1
2
a safety helmet and
visor .
Eye goggles do not give full face protection
a neck apron to protect the back of the
3
neck
4
a coverall with additional high visibility
5
heat resistant gauntlets/gloves .
Ensure that no bitumen can run into the
gloves (see latest Eurobitume
documentation)
6
7
a one piece protective coverall with
long sleeves and legs worn over boots
8
safety footwear, calf length .
No shoes, sandals, clogs or trainers.
NOTES:
During loading and discharging
it is recommended to wear well fitting
long sleeved gauntlets (see picture).
If close fitting wristlet gloves are used
the cuffs should always be worn inside
coverall sleeves.
In general there may be additional
PPE requirements from local sites eg
Personal Dose Monitor (PDM) for H2S
during loading operations.
Appendix 1
v1 2012
2. Product handling and sampling

Always use:
safety glasses
gloves
3
overall .
3
2
NOTES:
If close fitting wristlet gloves are used,
the cuffs should always be worn inside
overall sleeves. If taking bitumen samples,
full face protection must be used.
Always follow any site specific
requirements.
Appendix 1
v1 2012
Transport containers (tankers)

Trucks used for bitumen transport should
fulfil the technical specifications in the
countries where they are to be used.
Furthermore vehicles and tanks must fulfil
the demands of the ADR/RID/ADN/IMDG*
legislation.
It is essential that tankers are constructed
in such a way that they can be completely
emptied. (In the UK this is done by means
of dump valves. Air is released from the
trailer air suspension and this in turn lowers
the rear air suspension). It is also the reason
why road/railway tanks used for bitumen
transportation nowadays are built with a
completely smooth interior.
ADR legislative requirements should be
followed for tank manufacture with regard
to metal type in order for them to endure
high temperatures and large temperature
changes. The tanks should be well insulated
to maintain the temperature of the product
for as long as possible. Some tankers are
equipped with heating. Equipment is
chosen according to the geographical area
of transportation and the type of product
handled.
Two
Appendix 2 - ADR regulations
Labelling of vehicles according to

ADR regulations
This relates to UK, Nordic and Continental
marking requirements.
Dangerous goods have been divided into
nine different classes.
Within this classification each product is
assigned a UN number, packaging group and
a safety label code.
Bitumen is classified as dangerous due to
its high transport temperature (>100C,
below its flashpoint). Also the low flash
points of cutbacks may imply classification as
dangerous goods.
Bitumen is classified as follows:
UN 3257, ELEVATED TEMPERATURE
LIQUID, N.O.S. at or above 100C and
below its flash point (bitumen)
Class 9
Packaging group lll
Classification code M9.
Bitumen tanks should be constructed and

should function in such a way that the risk
of injuries is reduced to a minimum and the
product retains its quality, homogeneity and
temperature during transit.
* see section 14 of Safety Data Sheets (SDS)
Appendix 2
v1 2012
For UK domestic journeys the marking and

labelling for bitumen
Front
Rear and
both sides
For Nordic and Continental journeys the

marking and labelling for bitumen
Front and
rear
Appendix 2
Rear and
both sides
v1 2012
Nynas provides additional information sheets

on ADR 5.4.3
Additional Information for ADR 5.4.3. Instructions in Writing
3257
9
99
III
UN number :
ADR/RID Class :
Hazard identification number :
Packing group :
LOAD
Proper shipping name :

Name of product or products:
Physical state :
Colour :
Odour :
Solubility :
Elevated temperature liquid, N.O.S. at or above 100C and below its

flashpoint. (Bitumen) (D)
Bitumen
Liquid at normal handling temperature.
Solid at ambient temperature.
Brown to black
Characteristic.
insoluble in water.
NATURE OF DANGER
- Contact of hot liquid with skin causes severe burns.

- Overheating of product may result in fire or explosion.
- Contact with water will result in a violent expansion and a danger of boil-over.
- Respiratory problems or nausea may be induced by high concentration of fumes / vapours.
PERSONAL
PROTECTION
- Safety helmet with integrated full face visor and neck

protection
- One-piece protective coverall
- Safety footwear covering ankle
- Heat resistant gloves with long sleeves
- During loading/unloading there should be no areas of Additional equipment:
exposed skin and the face visor must be down !
- Local or national regulations may require specific
additional equipment to be carried.
GENERAL ACTIONS TO
BE TAKEN BY DRIVER
- Stop the engine.

- No naked lights. No smoking.
- Mark roads and warn other road users or persons passing by.
- Inform the public about the hazard and give advice to keep upwind.
- Notify police and fire brigade as soon as possible.
ADDITIONAL AND/OR
SPECIAL ACTIONS TO
BE TAKEN BY THE
DRIVER
- Only take action if without personal risk.

- Avoid direct contact with the product.
- Stop leaks if possible without risk.
- Contain or absorb leaking liquid with sand / earth or suitable material.
- If practicable : use shovel, broom, small collecting container.
- Prevent liquids from entering water courses, sewers, basements and workpits.
- If product has entered a watercourse or sewer or been spilt on soil or vegetation, advise Police.
FIRE
Information for the driver in case of fire:

- Do not attempt to deal with any fire involving the load.
Information for emergency services:

- Extinguish fire with water fog or fine spray, dry powder,
foam, inert gas, carbon dioxide, sand.
- Do not use water jet.
- Cool closed containers exposed to fire with water.
FIRST AID
In case of burns:
- Drench burn in cold water for a minimum of
10 minutes.
- Do not attempt to remove the bitumen unless blocking
an airway.
- Bitumen acts as a sterile layer and should only be
removed by specialist medical care.
- Send person for medical attention immediately.
- If product gets into the eyes, immediately wash out
with plenty of water and get medical attention.
In case of circumferential burns:

- Where hot bitumen completely encircles a limb or other
body part, the bitumen must be softened and/or split to
prevent restriction of blood flow during cooling
(tourniquet effect).
ADDITIONAL
INFORMATION
Date of issue :
Emergency phone:
2010-01-07.
+44 (0)208 762 8322
In case of respiratory problems:

- Under safe conditions remove person from
contaminated atmosphere into fresh air.
- Seek medical assistance if breathing remains difficult.
Version :
APPLIES ONLY DURING ROAD TRANSPORT
Appendix 2
v1 2012
This is not an extensive list but can be used as an example to formulate questions on site and
address specific requirements for loading bitumen vehicles.
BEFORE LOADING
1. Vehicle owner
2. Vehicle number
3. Load order number
4. Product required
5. Last load
6. Same product (compatible)?
yes - go to number 9/no - cleaning is required
7. Other product (non compatible)?
yes/no
8. Is cleaning required?
yes/no
9. Is tank dry, empty and clean?
yes/no
10. Is procedure loading required?
yes/no
11. Tank/barrel capacity

12. Number of compartments
13. Can tank/barrel carry requested amount?
yes/no
14. Are all tank/barrel valves closed shut?
yes/no
15. Vehicle correctly labelled?
yes/no
16. Correct product temperature?
yes/no
AFTER LOADING BUT BEFORE LEAVING

Delivery note
Instructions in writing (ADR 4 Page requirement)
(Hauliers responsibility)
Additional information to the ADR 5.4.3
Instructions in Writing
Nynas can provide additional information sheets to the ADR 5.4.3

Instructions in Writing (see Appendix 2).
Special directions / instructions (if applicable)

Necessary transport documentation on board
yes/no
Appendix 3
Three
Appendix 3 - Bitumen loading checklist
v1 2012
Appendix 4 - Bitumen unloading checklist
BEFORE UNLOADING
Contact with customers representative?
yes/no
Is the receiving tank number and labelling correct?
yes/no
Is there enough space in the receiving tank?
yes/no
Four
Check that the load corresponds to order
Customer signature for ullage

Correct connection for unloading?
yes/no
Is all emergency equipment working?
yes/no
Are high level alarms and tank gauges working properly?
yes/no
Is a safe exit route available?
yes/no
Appendix 4
v1 2012
Appendix 5 - Eurobitume Bitumen Burns Card
Five
Please check for updates of this card at www.eurobitume.eu
five
Appendix 5
v1 2012
BITUMEN BURNS
>> SECOND DEGREE BURNS

The bitumen should be left in place and covered with a Tulle dressing
containing paraffin or a burn ointment containing paraffin, e.g. Flammazine
(silver sulphadiazine). Such treatment will have the effect of softening the
bitumen enabling it to be gently removed over a period of days. As a result of
the natural re-epithelialisation of the wound any remaining bitumen will peel
off in time.
>> THIRD DEGREE BURNS
Active removal of the bitumen should be avoided unless primary surgical
treatment is being considered due to the location and depth of the wound. In
such cases removal of the bitumen is best carried out in the operating theatre
between the second and fifth day after the burn occurred. By the second day
the capillary circulation has usually recovered and the bed of the wound is
such that a specialist can assess the depth to which the burn has penetrated.
There are normally no secondary problems such as infections to contend with
before the sixth day. However, it is essential to commence treatment using
paraffin based substances from the day of the accident to facilitate removal
during surgery.
>> CIRCUMFERENTIAL BURNS
Where hot bitumen completely encircles a limb or other body part the cooled
and hardened bitumen may cause a tourniquet effect. In the event of this
occurring the adhering bitumen must be softened and/or split to prevent
restriction of blood flow.
>> EYE BURNS
No attempt should be made to remove the bitumen by unqualified personnel.
The patient should be referred urgently for specialist medical assessment and
appropriate treatment.
Considerable effort has been made to assure the accuracy and reliability of the information contained
in this publication. However, neither Eurobitume nor any company participating in Eurobitume can
accept liability for any loss, damage or injury whatsoever resulting from the use of this information.
Eurobitume would like to acknowledge the contribution of Drs M.J. Hoekstra and M.H.E. Hermanns of
the Burns Unit, Red Cross Hospital, Beverwijk, The Netherlands, in compiling this guide.
european bitumen association

E-mail: info@eurobitume.eu
Appendix 5
v1 2012
Appendix 6 - Bitumen storage and handling temperatures

(as recommended by Eurobitume)
The table gives an overview of best practice for handling each grade:
PAVING GRADE BITUMEN

10/20
15/25
20/30
30/45
35/50
Minimum pumping temperature
150
145
140
130
130
Typical storage temperature
175 - 190
175 - 190
165 - 185
160 - 180
155 - 175
Maximum handling/storage temp
200
200
200
200
200
40/60
50/70
70/100
100/150
160/220
125
125
120
115
110
150 - 170
145 - 165
140 - 160
135 - 155
130 - 150
200
200
190
190
190

250/330
330/430
500/650
650/900
100
95
90
85
125 - 145
120 - 140
115 - 135
110 - 130
190
180
170
160
OXIDISED BITUMEN
R&B <100C
R&B >100C
r&b + 80
r&b + 90
200 - 220
210 - 230
230
230
SOFT BITUMEN
V1500
V3000
V6000
V12000
60
65
70
80
80 - 130
85 - 135
90 - 140
100 - 150
130
140
150
150
Appendix 6
Six
v1 2012

This indicates the minimum temperature at which the bitumen reaches a suitable viscosity
for pumping, typically related to 2000 mPa.s.
For normal operations, temperatures 10C to 50C in excess of these may be selected to
facilitate transfer or blending operations but the maximum safe handling temperature must
not be exceeded.
A range is given for each grade. These cover the typical temperatures used for storage of the
bitumen and are consistent with achieving realistic loading rates and delivery to customer
storage tanks. The period during which bitumen is stored and circulated at elevated
temperature should be minimised to prevent hardening. If the bitumen is to be stored for
an extended period without addition of fresh material, the temperature should be reduced
to approximately 20C to 25C above the softening point with circulation stopped. When
reheating the process must be carried out carefully to prevent localised overheating and
operating problems.
Maximum handling/storage temperature
The recommended maximum storage and handling temperatures are based on generally
satisfactory experience for storage in contact with air subject to avoidance of flammable
atmospheres in the vapour space of the tank.
The maximum handling and storage temperatures vary according to bitumen grade but the
current recommended maximum for paving grade bitumen is 200C. For other grades please
refer to the appropriate Safety Data Sheets.
Appendix 6
v1 2012
Belgium
Luxemburg
Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-725 18 18
Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-725 18 18
Denmark
Netherlands
Nynas A/S
Lyngbyvej 20
DK-2100 Copenhagen
Tel: +45-39-15 80 80
Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-725 18 18
Estonia
Norway
AS Nynas
li 5
EE-74115 Maardu
Tel: +372-631 94 22
Nynas AS
Tollbugatan 39B
NO-3044 Drammen
Tel: +47 32 20 25 30
Finland
Spain
Nynas OY
Ayritie 12B
FIN-01510 Vantaa
Tel: +358-20-743 33 10
Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-709 68 51
France

Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-725 18 18
Switzerland
Germany
Poland
Nynas NV
Excelsiorlaan 87
BE-1930 Zaventem
Tel: +32-2-725 18 18
Nynas Sp. z o. o. n
Ul. Grnoslaska 17-18
PL-70-664 Szczecin
Tel: +48-91-462 31 21
Seven
Appendix 7 - Nynas bitumen sales offices
Nynas AG
Dammstrasse 19
CH-6301 Zug
Tel: +41-41-723 33 55
Appendix 7
v1 2012
Appendix 7 - Nynas bitumen sales offices
Sweden
United Kingdom
Nynas AB
PO Box 10700
121 29 Stockholm
Tel: +46-8-602 12 00
Nynas UK AB
North Road
Ellesmere Port CH65 1AJ
Tel: +44-151-327 31 71
Nynas UK AB
East Camperdown Street
Dundee DD1 3LG
Tel: +44-1382-462 211
Appendix 7
v1 2012
Appendix 7 - Nynas bitumen depots
Denmark
Poland
Nynas A/S
Kuwaitvej 3
DK-8000 rhus C
Tel: +45-861 273 44
Fax: +45-861 374 46
Nynas Sp. z o.o.

ul. Gornoslaska 17/18
PL-70-664 Szczecin
Tel: +48-914-623 121
Fax: +48-914-623 188
Nynas A/S
Sdr. Molevej 13-15
DK-4600 Kge
Tel: +45-566 550 50
Fax: +45-56-655014
Sweden
Estonia
AS Nynas
li 5
EE-74115 Maardu
Tel: +372-631 94 22
Nynas AB

Oljevgen 55

SE-418 78 Gteborg
Tel: +46 31 755 12 00
Fax: +46 31 755 12 01
Nynas AB
Tjrhovet
SE-392 31 Kalmar
Tel: +46 480 40 36 90
Fax: +46 480 40 36 91
France
Nynas NV
c/o LBC
Dpt de Bayonne
ZI
Route de la Barre
FR-40220 Tarnos
Tel: +32-2-7252238
Fax: +32-2-7251091
Nynas NV
c/o LBC
Dpt de Nantes
103, Quai E. Cormerais
BP 53
FR-44801 St-Herblain
Tel: +32-2-7252238
Fax: +32-2-7251091
Nynas AB
Oljehamnsvgen
SE-149 82 Nynshamn
Tel: +46 8 520 652 48
Fax: +46 8 520 165 10
Nynas AB
Box 18
SE-820 22 Sandarne
Tel: +46 270 42 84 05
Fax: +46 270 42 84 06
Nynas AB
Ume Uthamn

SE-913 32 Holmsund
Tel: +46 90 14 91 80
Fax: +46 90 14 96 09
Appendix 7
Appendix 7 - Nynas bitumen depots
Sweden
Nynas AB
c/o Vopac Logistics AB
Oljevgen 18

SE-211 24 Malm
Tel: +46 40 93 66 50
Fax: +46 40 18 39 63
Nynas AB
c/o Vopac Logistics AB
Bjrkuddsvgen 1
SE-151 38 Sdertlje
Tel: +46 8 550 115 38
Fax: +46 8 550 105 14
Nynas AB
Oljevgen 2

SE-721 32 Vsters
Tel: +46 21 12 06 47
Fax: +46 21 41 26 94
Appendix 7 - Emulsion plants
Estonia
Sweden
AS Nynas
li 5
EE-74115 Maardu
Tel: +372-631 94 22
Nynas AB
Oljevgen 55

SE-418 78 Gteborg
Tel: +46 31 755 12 00
Fax: +46 31 755 12 01
AS Nynas
Krkna kla
EE-60503 Tartu
Tel: +372-736 61 44
Nynas AB
Kritvgen 1

SE-941 00 Pite
Tel: +46 911 633 20
Fax: +46 911 633 20
Nynas AB
Cisterngatan 3
SE-721 32 Vsters
Tel: +46 73 029 70 89
Fax: +46 70 662 24 78
Appendix 7
v1 2012
Appendix 8 - Glossary
American Petroleum Institute
CLP

EU regulation 1272/2008 on Classification Labelling and Packaging of

substances and mixtures
Concawe

CONservation of Clean Air and Water in Europe. The oil companies

European association for environment, health and safety in refining and
distribution
CSA
Chemical Safety Assessment
DNEL
Derived No Effect Level
ECHA
European Chemical Agency
Eurobitume
The European Bitumen Association
FPC
Factory Production Control
GHS
Globally Harmonised System of Classification and Labelling of Chemicals
Hazard
The potential to cause harm
IARC
International Agency on Research on Cancer
OEL
Occupational Exposure Limit
PAHs
Polycyclic Aromatic Hydrocarbons
PBT
Persistant Bioaccumulative and Toxic
PDM
Personal Dose Monitor (H2S)
PNEC
Predicted No Effect Concentration
ppm
parts per million
vPvB
Very Persistant and Very Bioaccumulative
PPE
Personal Protective Equipment
REACH

EU regulation 1907/2006 on Registration Evaluation Authorisation and

Restriction of Chemicals
Risk
The likelihood of harm
SDS
Safety Data Sheet
TWA
Time Weighted Average
THC
Total Hydrocarbon Concentration
UVCB

Unknown or Variable Composition Complex reaction products or

Biological Materials
Eight
API
Appendix 8
v1 2012
Management system standards

ISO 9001

is a global quality management standard. ISO 9001 applies to all types of

organisations. It can help both product and service organisations achieve
standards of quality that are recognised and respected throughout the
world.
ISO 14001

is an environmental management standard. It specifies a set of

environmental management requirements for environmental management
systems. The purpose of this standard is to help all types of organisations to
protect the environment, to prevent pollution and to improve their
environmental performance.
OHSAS 18001

is an occupational health and safety management standard. It defines a set

of occupational health and safety (OH&S) management requirements for
occupational health and safety management systems (OHSMS).
CE Marking

CE Marking is a legal requirement to place bitumen - for use in paving

applications - on the EU market, except in those countries where CE
Marking is optional to date.
CE Marking on a product is a manufacturers declaration that the product

complies with the essential requirements of the Construction Products
Directive of the European Union and indicates that the product complies
with the relevant national standards transposing the harmonised European
standards and that all the tasks linked to attestation of conformity have
been completed.
CE Marking is not a mark of origin.
CE Marking is the evidence of conformity to the requirements described in

the harmonised product standards.
CE Marking is only possible for those products for which a harmonised

European product standard is available.
The manufacturer must have a system of Factory Production Control (FPC)

in place. FPC has a set of procedures, inspections and tests to control and
ensure the quality and properties of the finished product. The FPC system
covers all manufacturing sites for which CE Marking is required.
External auditing is performed by a certified body whose task is to check

that the quality systems and documentation comply with the requirements
of Annex ZA in the product standard, by visiting the location and examining
the relevant processes, records etc.
Appendix 8
v1 2012
Other
Air-rectified bitumen

Bitumen that has undergone a mild degree of air-blowing for

adjustment of the physical properties. Penetration index 2.0.
Severely oxidised bitumen

Bitumen products that have undergone intensive air-blowing, in

some cases with the presence of a flux. Penetration index >2.0.
Hazardous substances

Substances that, following exposure, can have an adverse effect

on health. Examples of hazardous substances include poisons,
substances that cause burns or skin and eye irritation and
substances that may cause cancer.
Dangerous goods

Substances or articles that, because of their physical, chemical

(physicochemical) or acute toxicity properties, present an
immediate hazard to people, property or the environment.
Types of substances classified as dangerous goods include
explosives, flammable liquids and gases, corrosives, chemically
reactive or acutely (highly) toxic substances.
Appendix 8
v1 2012
Appendix 9 - References
Concawe publications: www.concawe.be

Echa publications: www.echa.europa.eu
Eurobitume publications: www.eurobitume.eu
Nynas publications: www.nynas.com
Information relating to ADR/RID/ADN legislation is available on the UNECE Transport Division
website page www.unece.org/trans/danger/danger
References
Information relating to IMDG legislation is available on the website page http://gisis.imo.org/public

or www.imo.org/publications
B0801204ENG
www.nynas.com

Safe Handling of Bitumen

Uploaded by

Copyright:

Available Formats

Safe Handling of Bitumen

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Safe Handling of Bitumen

Uploaded by

Copyright:

Available Formats

Safety is No Accident

Observe, think and act

Safe Handling of Bitumen

Nynas Policy for Health Safety Security Environment &

Nynas is a different kind of oil company.

night, at remote locations. Our customer

Nynas Policy for Health Safety Security

The hauliers responsibilities

Loading plan - tank cleaning

Sampling bitumen products

4. Handling and storage

Tank construction and inspection 4.4

Venting pipes and other

Bitumen storage tank

Cleaning and emptying of tanks

2. Health, safety and environment

Classification Labelling and

Hot bitumen in contact with water 2.4

1. Personal Protective Equipment (PPE)

Exposure to bitumen fumes

3. Bitumen loading checklist

Skin contact with cutbacks

5. Eurobitume Bitumen Burns Card

Emissions and other

6. Recommended bitumen storage

7. Nynas sales offices, depots and

4. Bitumen unloading checklist

Preventing accidents during

The suppliers responsibilities

Bitumen is a non volatile, adhesive and

Bitumens are very complex mixtures of

* dalton (Da) is a unit used to indicate the mass on

There are three main types of bitumens.

An intense degree of blowing (oxidation)

Bitumen is also used as a raw material

emulsions may also contain a fluxing agent

Modified bitumens usually contain

Bitumen emulsion surface treatment.

Wax modified binders exhibit lower

Greatly enlarged picture of bitumen emulsion.

The bitumen content of an emulsion

In Europe the cationic emulsions are most

The quality and performance of bitumen can

Deterioration and softening of asphalt due to

It is essential that bitumen is handled and

A damaged road that suggests the defects could

Nynas offers a wide range of bitumen

Health, safety and

Health, safety and environment

REACH is the European regulation on

a risk characterisation which identifies if

The risk characterisation consists of a

European bitumen manufacturers have

Derived No Effect Level:

Predicted No Effect Concentration:

Safety Data Sheets

DNEL/PNEC - both DNEL and PNEC are

Classification Labelling and Packaging

Classification Labelling and Packaging (CLP)

Bitumen is normally manufactured, stored,