Vol1 AOM Part1

Aerosoft Digital Aviation
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-1
AIRCRAFT GENERAL / IN FSX
09-Sep-2015
Rev #
Date
Author
Change
Version
001
9-Sep-2015
MK
Start of documentation
0.50
002
18-Sep-2015
MK
Pre Release Candidate
0.90
003
18-Sep-2015
MK
Adding Manager details
0.91
004
21-Sep-2015
MK
Spellchecked and many small things changed
0.92
On behalf of Authority
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-2
09-Sep-2015
TABLE OF CONTENTS
INTRODUCTION..................................................................................................................................... 4
CREDITS................................................................................................................................................. 4
INSTALLING & REMOVING .................................................................................................................... 4
DOWNLOAD ...................................................................................................................................... 4
BOXED ............................................................................................................................................... 5
REMOVING........................................................................................................................................ 5
COPYRIGHTS ......................................................................................................................................... 5
MANUALS ............................................................................................................................................. 5
CONTACT SUPPORT .............................................................................................................................. 6
NAVIGATION DATABASE ....................................................................................................................... 6
VERSION NUMBERS .......................................................................................................................... 6
THE CRJ ................................................................................................................................................. 6
BASIC FACTS ...................................................................................................................................... 7
PILOT INFORMATION FOR TRANSITIONING TO THE BOMBARDIER CRJ700 AND 900 ........................... 7
GEOMETRY ........................................................................................................................................ 7
SYSTEMS ........................................................................................................................................... 8
FLIGHT CHARACTERISTICS ................................................................................................................. 9
AVIONICS AND FLIGHT MANAGEMENT SYSTEM (FMC)..................................................................... 9
THE CRJ IN FLIGHTSIM ........................................................................................................................ 11
LOADING THE CRJ ........................................................................................................................... 11
THE VIRTUAL COCKPIT OVERVIEW .................................................................................................. 11
OVERHEAD PANEL ........................................................................................................................... 12
GLARESHIELD / AUTOPILOT PANEL ................................................................................................. 14
WARNING / ANNUNCIATOR LIGHTS PILOTS SIDE ........................................................................ 15
CENTER INSTRUMENT PANEL.......................................................................................................... 16
CAPTAINS INSTRUMENT PANELS .................................................................................................... 17
CAPTAIN SIDE CONTROL ................................................................................................................. 18
UPPER PEDESTAL ............................................................................................................................ 19
LOWER PEDESTAL ........................................................................................................................... 20
PRE-DEFINED VIEWS ........................................................................................................................... 22
MCDU KEY INPUT ................................................................................................................................ 22
ADDITIONAL TOOLS / OPTIONS........................................................................................................... 24
SAVING AND LOADING A FLIGHT .................................................................................................... 24
USING PANEL STATES .................................................................................................................. 24
DAVE ............................................................................................................................................... 24
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-3
09-Sep-2015
CHECKLISTS ................................................................................................................................. 24
FUEL PLANNER ............................................................................................................................ 24
V-SPEEDS ..................................................................................................................................... 25
OPTIONS ..................................................................................................................................... 25
SERVICES / MAINTENANCE ......................................................................................................... 25
DOORS ........................................................................................................................................ 25
CRJ MANAGER................................................................................................................................. 25
LIVERY MANAGER ........................................................................................................................... 26
ROUTE SUGGESTIONS ......................................................................................................................... 27
DIGITAL AVIATION CRJ900 FLIGHT FROM DSSELDORF (DUS) TO Basel (BSL) ................................ 28
FLIGHT PLANNING ....................................................................................................................... 28
DEPARTURE FROM DUSSELDORF AIRPORT ................................................................................. 30
ENGINE START AND PUSHBACK ON APRON POSITION ............................................................... 31
TAXIING TO RUNWAY 26L ........................................................................................................... 31
TAKE-OFF ON RWY 23L ............................................................................................................... 31
CLIMB AND CRUISE ..................................................................................................................... 33
ARRIVAL TO Basel AIRPORT ......................................................................................................... 34
FINAL APPROACH DIRECTION RWY 15 ........................................................................................ 35
LANDING ..................................................................................................................................... 35
PARKING AND SECURING THE AIRCRAFT .................................................................................... 35
DISCLAIMER ................................................................................................................................ 36
EXTENDED FLIGHT PLAN EDDL-LFSB (SOURCE VATROUTE) ......................................................... 36
EXTENDED FLIGHT PLAN EDDL-LFSB (SOURCE AIVLASOFT EFB) .................................................. 37
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-4
09-Sep-2015
INTRODUCTION
Thank you very much for purchasing Digital Aviation/Aerosoft CRJ700 / CRJ900 package. Development of the
package went through a lot of highs and lows. Thank you for bearing with us.
The CRJ is a typical regional jet to connect smaller airports or remote areas with the bigger hubs. Hence the
CRJ is able to get fast up to cruise altitude and stay there pretty long, but is not designed for world record
cruise speeds.
The CRJs history goes back into the 80s, when first studies were made regarding options to create a regional
jet out of the Challenger 600 business jet. Near the end of the 80s Lufthansa pushed the idea again and the
project was actually started in 1989 with the maiden flight in 1991 and certification in 1992: the CRJ100 was
born. The CRJ200 was developed later on basis of the CRJ100 and equipped with better engines. Both versions
carry 50 passengers.
When the CRJ700 was developed, the fuselage was stretched further to accommodate 70 passengers.
Accordingly the wings needed to be modified, and furthermore new winglets and new engines were attached.
Its maiden flight was in May of 1999. On basis of the CRJ700 the CRJ900 was developed. The fuselage was
stretched again to accommodate 90 passengers.
The CRJ700 / 900 by Digital Aviation/Aerosoft comprises the CRJ700ER and CRJ900ER models with flight
dynamics modelled according the respective flight performance data and of course 3d representations as close
as possible in FS to the real thing. Accurate systems programming reflects behaviour of the real CRJ within
normal operations.
CREDITS
Programming:
3d Modelling, Texturing:
Flight dynamics:
Sound:
Documentation:
Metzger
Project Management:
Advisors:
Livery Manager:
Additional Liveries:
Hans Hartmann (Digital Aviation)

Stefan Hoffmann (Aerosoft)
Alexander Metzger (Digital Aviation)
Turbine Sound Studios
Ingo Voigt (Digital Aviation), Mathijs Kok (Aerosoft), Alexander
Mathijs Kok (Aerosoft)
XX
Hauke Fehr (Fehrware.de)
Holger Sobl
The beta testers of this product deserve special mentioning. In this development we experimented extensively
with involving them directly in the production, they often tested code minutes after it was written, gave
feedback and got new code almost immediate. Without them the product would not be where it is now.
INSTALLING & REMOVING

Installing the product correctly is the first step to getting airborne. Please follow the steps below to avoid
problems.
DOWNLOAD
The downloaded file can be unpacked to any location on your system. We strongly recommend using these
steps to install:
CRJ-700 CRJ-900
1.
2.
3.
4.
5.
6.
AOM PART 1
VOL
1-1-5
09-Sep-2015
Reboot your computer

Log in with administrative rights
Disable the anti-virus software temporary
Install the product
Enable the anti-virus software
Defragment your disk (NOT if you are using an SSD)
BOXED
After inserting the DVD the installer will start automatically (if not navigate to the DVD and start the
setup.exe). We strongly recommend using these steps to install:
1.
2.
3.
4.
5.
6.
Reboot your computer

Log in with administrative rights
Disable the anti-virus software temporary
Install the product
Enable the anti-virus software
Defragment your disk (NOT if you are using an SSD)
REMOVING
Never remove this product by manually removing the files but to use the Windows Software control panel.
COPYRIGHTS
The manual, documentation, video images, software, and all the related materials are copyrighted and cannot
be copied, photocopied, translated or reduced to any electronic medium or machine legible form, neither
completely nor in part, without the previous written consent of AEROSOFT. THE SOFTWARE IS FURNISHED AS
IS AND IT DOES NOT COME FURNISHED WITH ANY GUARANTEE IMPLICIT OR EXPRESS. THE AUTHOR DECLINES
EVERY RESPONSIBILITY FOR CONTINGENT MALFUNCTIONS, DECELERATION, AND ANY DRAWBACK THAT
SHOULD ARISE, USING THIS SOFTWARE.
Copyright 2015 AEROSOFT / Digital Aviation. All rights reserved. All trademarks and brand names are
trademarks or registered trademarks of the respective owners.
Copyrights are serious stuff. If you find any pirated copies of this software please notify us at
support@aerosoft.com. We will make sure reports of copyrights violation are rewarded.
Aerosoft GmbH
Lindberghring 12
D-33142 Bren, Germany
www.aerosoft.com
MANUALS
The documentation for the CRJ700 / CRJ900 comprises of several documents:
Vol.1: AOM part I General Information. You are reading this manual at the moment. Contains
information on installation, where to find support, manual structuring, some basic information on the
CRJ, a transition guide for experienced users, an introduction to loading the CRJ, the external model,
its cockpit, keyboard commands, tools coming along with the CRJ, and some flight suggestions apart
from the tutorial.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-6
09-Sep-2015
Vol.2: Quick Reference Handbook, QRH. Contains information on procedures, limitations and aircraft
performance.
Vol.3: Tutorial. Tutorial flight which takes you from Los Angeles to Monterey guiding you through a
flight from preparation to shutdown.
Vol.4: Normal Ops Checklist. Short checklists on two pages for experienced pilots
Vol.5: AOM part II - Systems Manual. Introduction and explanation on the CRJs systems.
Vol.6: AOM part III Flight Management System, FMS manual. In depth explanation on the Flight
Management System
You will find that we discuss the project in FSX a lot. If you are using Prepar3D V2 it should not be a problem
finding the same locations and settings. If there is a problem just contact us and well assist!
Also note that the readme.txt always contains the information on the latest updates. Before contacting
support do make sure you installed the latest version!
CONTACT SUPPORT
Support for this product is done by Aerosoft. We prefer to do support on the support forum for one simple
reason, it is fast and efficient because customers help customers when we are sleeping. Its also the difference
between one support person reading the question and 500 people, some of why know a LOT about the
aircraft.
CRJ Support Forums: http://forum.aerosoft.com/index.php?/forum/747-crj-700900/

If you prefer support by email: https://aerosoft.zendesk.com/anonymous_requests/new
Please note that email support can be slow when things are busy (shortly after a major release form
example). We try to get back to you in 24 hours, but if you want an answer fast, got to the forums.
We feel strongly about support. Buying one of our products gives you the right to waste our time with
questions you feel might be silly. They are not.
NAVIGATION DATABASE
With this CRJ comes a complete copy of the NavDataPro navigation database. This database contains the LIDO
data and is the worlds most used navigation database in aircraft. The database is fully updateable; check its
product page on our websites: www.aerosoft-shop.com/products/navdatapro/navdatapro.html
The CRJ is fully compatible with the well-known Navigraph database. Although these databases come from a
different source and have some differences they are basically the same and you should not see any differences
between the two.
VERSION NUMBERS
The release version number will be 1.00.

A service pack will show in the tens, 1.10 (first service pack) -> new full build
A hotfix will show in in the hundreds 1.11 (first hotfix to be put on service pack 1)
When there are many hotfixes we will also make full new builds. If you are ever in doubt which version you
have, check the product.cfg that you can find in FSXMainFolder\Aerosoft\CRJ*.
THE CRJ
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-7
09-Sep-2015
As we already looked into the CRJs history during the introduction this chapter provides some basic facts on
the CRJ.
BASIC FACTS
CRJ700
CRJ900
Length
32,3 m
106 ft 1 in.
36,2 m
118 ft 11 in.
Wingspan
23,2 m
76 ft 3 in.
24,9 m
81 ft 7 in.
Height
7,6 m
24 ft 10 in.
7,5 m
24 ft 7 in
Dry Operating Weight
20290kg
44731lbs
22131kg
48790lbs
Maximum zero fuel

weight (MZFW)
28259kg
62300lbs
31751kg
70000lbs
Maximum Payload
8190kg
18055lbs
9907kg
21840lbs
Cargo Weight
2438kg
5375lbs
2756kg
6075lbs
Maximum Ramp Weight
34133kg
75250lbs
37735kg
82750lbs
Maximum take-off
weight (MTOW)
34019kg
75000lbs
37421kg
82500lbs
Maximum landing weight

(MLW)
30391kg
67000lbs
33340kg
73500lbs
Maximum Seat Capability

Maximum range
70
90
2553 km
1378 nm
2439 km
1317 nm
Max. Cruise Speed
473 kts
0.825 Mach
470 kts
0.82 Mach
Takeoff field length

(ISA, Sea Level, Max.
Takeoff Weight)
1605 m
5040 ft
1847 m
6060 ft
Landing field length

(ISA, Sea Level, Max.
Landing Weight)
1536 m
5040 ft
1603 m
5260 ft
PILOT INFORMATION FOR TRANSITIONING TO THE BOMBARDIER CRJ700 AND 900

(By Alexander Metzger)
For those simulator pilots who transition from larger airliners, like an Airbus 320 or a Boeing 737, we would
like to provide you with important information on the specific differences flying the Canadair Regional Jet
(CRJ).
The aim of the development team was to properly transpose the real plane into a simulation that is enjoyable
to beginners and advanced simulation pilots. This document is focused on the differences of the CRJ700 and
CRJ900 in comparison to other airlines you may be familiar with. We encourage you to read the other manuals
so that you will be familiar with the cockpit and the systems that have been simulated at a very high level of
detail.
GEOMETRY
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-8
09-Sep-2015
On the first look from outside, it is obvious that the CRJ has been realized with a different concept of engine
arrangement in the back of the aircraft. As engines are relatively heavy, consequently the wing position, in
reference to the fuselage length, is also much more rearward, to assure that the centre of gravity of the empty
or fully loaded aircraft is within the limits of the wing chord to assure a stable flight behaviour.
Loading the aircraft properly is therefore vital for sufficient control of the elevator which has less of an arm for
pitch control than on a classical arrangement. Please refer to the trim tables to be properly trimmed for takeoff depending on weight and centre of gravity index.
The big advantage of positioning the engines at the rear end of the fuselage is a lighter wing construction no
need to carry the heavy engines and having the whole surface and shape available to produce the required
lift in respect to aircraft weight. This wing is optimized for high speeds and supported by slats and flaps for the
slower flying regime during take-off and approach/landing.
There is also a very noticeable difference while flying an aircraft with that engine arrangement when applying
power changes. On the CRJ the engine thrust is pushing at a position higher than the centre of gravity and
above the wing. This results in a pitch down moment when increasing power and consequently a pitch up
moment when pulling engine levers to idle. While in cruise the autopilot would eliminate this with trim
commands, it is specifically important to bear this in mind during the final landing phase, especially the flare
onto the runway. You need very little pull on the yoke when you slow the descent and retard the engines
before touch down.
Do not retard the engines to idle 50 ft. or even higher, as this will lead to a pitch up of the CRJ and fast loss of
speed too high above the runway and requires a corrective nose down push to avoid a hard landing.
Opposite to the landing, the full power during take-off pushes the nose down and you need pull the yoke
substantially to initiate the rotation. The pitch down attitude, characteristic for these two planes while on
ground, is not helping either to get airborne. Therefore pull firmly, rotate with about 3/s to 15-18 pitch and
trim for the initial climb speed.
A specialty of the CRJ is its automatic trim movement when flying manually and extending or retracting flaps
between the positions UP-1-8-20. This automatic trim travel supports the pilot hand-flying the aircraft when
there is a need to compensate the impact from changing flaps configuration with intense lift changes that
require pitch control.
SYSTEMS
Regional jets are typically doing many flights per day and so does the crew. Bombardier has therefore
automated many systems to release the pilots from routine procedures. Examples are the two button only
start-up of the APU with automatic bleed air assignment. Similar the main engines single button start-up and
thereafter fully controlled by the Full Authority Digital Engine Control (FADEC) system.
Fixed throttle detents for the take-off and climb help setting the correct power for these conditions of flight.
On the other hand the CRJs do not have an auto-throttle system and therefore the pilot flying needs to
manage power in cruise and descent. It also has no vertical navigation capability (VNAV) and therefore decent
planning is in the pilots hand and experience.
In return, there is no need to worry about switching bleed air for controlling cabin pressure or during anti-ice
operations. But due to the smaller engines, the loss of power from using bleed air for heating the wings
leading edge is more noticeable than on a larger aircraft. The climb performance is significantly reduced
despite the setting for N1 targets are a bit higher.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-9
09-Sep-2015
Further, do not be surprised by the increase of N1 and consequent thrust increase during a descent with idle
power when switching on anti-ice. The engines need to turn faster to maintain cabin pressure while hot air
from the turbine is deviated and guided to the engine cowlings and wing leading edges. This can ruin your
planned descent path by picking up more speed and requiring lower rates of descent and it is better to
anticipate icing early in the planning of the descent schedule than being forced to use spoilers to obtain
required rate of descent and not exceeding speed limits.
The two screens in the centre of the panel provide you with a wealth of information on system status, error
awareness or alerts. They also have dedicated screens for the controls and the monitoring role of the pilots
during the start-up of the systems all the way to the engines. We have modelled these pages with great care
and realism. Details can be found in the provided systems documentation and also in the tutorial flights.
FLIGHT CHARACTERISTICS
Beyond the above mentioned specifics of a tail driven aircraft, the CRJ is very stable in flight with easy roll and
pitch response in the speed range that may be typically flown by hand.
At cruise speed the response is very direct and minimal yoke input is required. The lower weights versus the
bigger aircraft you may know make it also more receptive to air turbulence.
In the lower range of the speed band, the controls are becoming less sensitive, but still remain more on the
sportive side as it is a light aircraft with significant less inertia on roll versus an aircraft with wing mounted
engines.
Due to the slats and efficient flaps, you typically have a high margin to stall speed and that enables low landing
speeds and short runways. Pitch attitude during descent and on final is often negative and becoming slightly
positive at reference speed providing a good forward view.
As soon as pitch establishes around +2 during the approach, it is time to select the next flaps setting.
The landing gear has very little drag and hardly any pitch effect. Slats and flaps shall be used to slow down the
aircraft and the flight spoiler may assist when you have left little time to adjust speed but dont expect
miracles from them, especially on the CRJ900.
In flare, level pitch will not cause a nose gear first touchdown as it is shorter than the main gear. The low wing
has a significant ground effect and the CRJ has a tendency to float forever if you come in just a bit too fast for
the landing weight. You need to set down the nose gear gently and pay specific attention when you use
reverse thrust immediately after ground contact.
On outbound taxi, the CRJ starts rolling with a little power push initially and maintains taxi speed close to idle.
On inbound taxi, you may need to use the brakes from time to time to avoid exceeding apron speed limits.
AVIONICS AND FLIGHT MANAGEMENT SYSTEM (FMC)
Every major aircraft producer favours his avionics provider and even when you are used to a Dash-400 built by
the same manufacturer Bombardier as the CRJ, you need to get familiar with the display and the programming
technique of the FMS used on the CRJ700 and CRJ900.
Please refer to the information provided in the systems description and the procedures as part of the tutorial
flights. Two main screens directly located in front of you provide you with a wealth of information on your
flight situation from an aerodynamic point of you and from a navigational perspective. Again, please familiarize
yourself with the many options of displaying data and graphical awareness displays for navigation and route
following.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-10
09-Sep-2015
We would like to encourage you to properly fly the CRJ700 and CRJ900 by investing some time to build a
knowledge base for proper operation.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-11
09-Sep-2015
THE CRJ IN FLIGHTSIM

The following chapter describes how to load the CRJ700 or CRJ900 in your flight simulator, which animations
(like opening doors, cargo hatches) are available, a brief tour of the virtual cockpit with a short overview of
available panels and pre-defined views, closing with the concept of operation (i.e. how do switches,
pushbuttons, etc. work in your flight sim).
LOADING THE CRJ
Its important that your simulator is running with Administrative rights to
avoid problems. This is especially important when your simulator is
installed in the default location (Program Files). If you are not logged in
with administrative rights you can still have the simulator running with
Administrative rights by right clicking and selecting [Run as administrator].
Before loading the CRJ we STRONGLY advise you to load one of the
default FSX aircraft with the engine running. This will avoid a load of
problems.
THE VIRTUAL COCKPIT OVERVIEW

To prevent pilots searching the entire cockpit for a certain knob, the entire cockpit is divided into several
panels. The following picture shows a view of the entire virtual cockpit and numbers indicate the respective
panels. Note that elements described in grey are not simulated.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-12
09-Sep-2015
1.Overhead
2.Glareshield/Autopilot
3. Centre Instrument Panel
4. Captain Instrument Panel
5. Captain Side Panel/Side console
6. First Officer Instrument Panel
7. First Officer Side Panel/Side

Console
8. Upper Pedestal
9. Lower Pedestal
OVERHEAD PANEL
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-13
09-Sep-2015
1. Electrical Power
2. Fire Detection Test System
3. Hydraulic Shutoff Valves (SOV)
4. Externa Lighting Controls
5. Fuel Controls
6. Pneumatic Controls
7. Auxiliary Power Unit Controls
8. Engine Start Panel
9. Hydraulic Controls
10. Emergency Locator Transmitter
11. Cabin Pressure Controls
12. Air Conditioning Controls
13. Anti-Ice Controls
14. Internal Lighting Controls
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-14
09-Sep-2015
GLARESHIELD / AUTOPI LOT PANEL
1. Standby / Whiskey Compass (Traditional compass,

normally only used to check alignment of electronic
compasses.)
2. Seat Position Sight Gauge (Used to position the seats so

your eyes are always in the same location. They gray ball
should hide the gold balls.)
3. Warning / Annunciator Lights Captains Side
4. Navigation / Flight Director / Autopilot control Panel
5. Warning / Annunciator Lights First Officers Side
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-15
09-Sep-2015
WARNING / ANNUNCIATOR LIGHTS PILOTS SIDE
1. ROLL SEL and PLT / CPLT ROLL. The ROLL SEL light comes
on, to indicate that roll priority selection I necessary. The
PL / CPLT ROLL illuminates green to indicate which side
(Captains or First Officers) has been selected for spoileron
control.
2. Master Warning Light. The red Master Warning Light is

illuminated and an aural warning sounds, in case a EICAS
warning message is triggered.
3. Master Caution Light. The amber Master Caution Light

is illuminated and an aural warning sounds, in case an
EICAS caution message is triggered.
4. Stall Warning Light / Switch. Illuminates in case a stall

warning is triggered. After opening the switch protection
the stall warning switch may be pressed to trigger the stall
warning test sequence.
5. Pull Up / GND PROX Warning Light. The Ground

Proximity Warning System, GPWS, may trigger the Pull Up
/ GND PROX warning light depending on the current mode
and warning.
6. LH ENG FIRE Switch.The LH/RH ENG FIRE Switch

illuminates in case an engine fire is detected. Pushing the
switch cuts engine fuel, bleed air and closes the hydraulic
shutoff valves.
7. BOTTLE 1 and 2 ARMED PUSH TO DISCH

The CRJ is equipped with 2 squibs which contain halon to
at least try and extinguish an engine fire. After pressing
the ENG FIRE switch the squib is armed and the BOTTLE 1
and 2 ARMED PUSH TO DISCH switch illuminates.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-16
09-Sep-2015
1. Course 1 Selector
2. Flight Director Switch
3. Auto Pilot Engage Switch
4. Auto Pilot Disengage Switch
5. XFR Mode Switch
6. Turbulence Mode Switch
7. Speed Mode Selector
8. Speed Selector
9. Approach Mode Selector
10. B/C Mode Switch
11. Heading Mode Selector
12. Heading Selector
13. NAV Mode Selector
14. Half Bank Mode Switch
15. Altitude Mode Selector
16. Altitude Selector
17. Vertical Speed Mode Selector
18. Vertical Speed Selector
19. Course 2 Selector
20. Flight Director Switch
CENTER INSTRUMENT PA NEL
1/3. EICAS Display No. 1. Engine Indicating and Crew

Alerting System two displays are available to indicate
engine data and a number of pages with aircraft
information like status of the hydraulic systems.
2. Integrated Standby Instrument Panel

Backup instrument for the attitude direction indicator,
speed indicator and altitude indicator.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-17
09-Sep-2015
CAPTAINS INSTRUMENT PANELS
1. Nose wheel Steering Switch
2. Cockpit Light Controls
3. Windshield Wiper Switch
4. Stall PTCT Pusher Switch. Controls

the Stick Pusher.
5. Clock / Stopwatch
6. Bearing Selector Switch. Switches

navigation reference between NAV1,
NAV2 and ADF1.
7. Format and Range Selector.

Controls MFD format (PLAN, MAP
HSI, weather radar, TCAS) and range.
8. Navigation Course Selector.

Switches navigation source between
FMS1, FSM2, NAV1, NAV2.
9. Vertical Speed Selector. Adjusts the

vertical speed shown on the PFD.
10. Decision Height / Minimum

Descent Altitude selector.
Enables to select whether the
decision height (DH) or minimum
descent altitude (MDA) is indicated
and adjust the value.
11. Barometric selector. Allows

selection in Hg or mbar and adjust the
value.
12. Revisionary Panel. Used to switch

the MFD to PFD, NORM (navigation
information) or EICAS mode.
13. Primary Flight Display, PFD

Combines several instruments in one:
attitude direction indicator, airspeed
indicator, altimeter, vertical speed
indicator, horizontal situation
indicator, V-Speed bugs.
14. Multi-Function-Display, MFD

Offers several display modes (Map,
Plan, Horizontal Situation Indicator,
Weather radar, TCAS) and may be
switched to different nav sources
(FMS, VOR)
15. Voice Recorder Control Panel
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-18
09-Sep-2015
CAPTAIN SIDE CONTROL
1. Skycam. Used to monitor different cameras, for

example to see who is at the cockpit door.
2. Steering Tiller. Used to steer the nose wheel at

low speed.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-19
09-Sep-2015
UPPER PEDESTAL
1. Captain side Flight Management System
2. First Officer side Flight Management System
3. Brake Temperature Monitor System. Used to reset the

system and silence the horn.
4. Anti-Skid Switch. Arms or deactivates the anti-skid

system.
5. MLG BAY Test switches. Test switches for Main Landing

Gear Bay Overheat
6. Gear Lever.
7. Engine Synchronization Switch. The left and right

engines rpm may be synchronized automatically for noise
abatement.
8. Ground Proximity Warning Switch. Illuminate

depending on the activated GPWS mode pressing the
switch silences the associated warning.
9. Roll Disc Handle. Disconnects the control wheels in case

one yoke is jammed.
10. Spoiler Switch. To arm automatic extension of the

ground spoilers after touchdown.
11. Reverser Switches. Arms the reversers so that they

may be deployed during landing roll.
12. Spoiler lever. To extend and retract the spoilers.
13. Thrust Lever. To control thrust (from fuel shutoff to

full power).
14. Pitch Disconnect. Disconnects the control wheels in

case one yoke is jammed.
15. Flap Lever. Used to extend and retract the flaps.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-20
09-Sep-2015
LOWER PEDESTAL
1. Radio Tuning Units. Used to tune communication,

navigation stations as well as the transponder.
2. Audio Control Panels. Used to control sound volume for

several audio sources like navigation station aural
identifiers.
3. Weather Radar Controls.
4. Backup Tuning Unit and ATC Selector Switch. Used to

select the active transponder and a backup tuning unit in
case the RTU fails.
5. Stab / Mach trim Switches. Controls for the Mach and

stabilizer trim.
6. Avionics Fan Controls.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-21
09-Sep-2015
7. Inertial Navigation System Controls, IRS Switches.

Selector knobs for the modes of the IRS system
8. Parking Brake Lever. To set and release the parking

brake.
9. Flight Deck Door Control. Controls for the flight deck

door to deny or allow access to the cockpit.
10. EICAS Control Panel. Panel to select different EICAS

pages.
11. Aileron and Rudder Trim Controls.
12. Cockpit Lightings Controls.
13. Yaw damper switches. Used to activate / deactivate

the yaw dampers.
14. Intercom Control Panel. Used on the real plane to

control communication within the aircraft like passenger
addressing, crew calls, emergency calls and sounding a
chime.
15. Source Selector Panel. The source selector panel

allows to select air data sources as well as switching the
displays to different modes in case a display fails.
16. Landing Gear Alternate Extension. In case the gear

does not extend when selecting gear down via the gear
lever, the alternate gear extension lever may be used to
extend the gear.
17. Air Driven Generator Controls. In case the CRJs engine

and the APU fail a little propeller might be extended which
produces sufficient electrical power to supply the most
important aircraft systems.
18. Head-up Guidance System Controls.
19. Cargo Fire Panel. Controls for fire extinguishing

systems for the cargo areas.
20. Emergency Flap Lever. In case controlling the flaps via

the flap lever is not working the CRJ provides an
emergency flap control.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-22
09-Sep-2015
PRE-DEFINED VIEWS
The CRJ700 / CRJ900 has no 2d-panels. Instead a set of pre-defined views is available which are similar to a 2dpanel. The following list shows the available views and their respective key assignment / hot key. Of course
these views can be undocked and moved to other monitors.
Hot Key
View
Shift + 1
Captains VFR View
Shift + 2
CPT Overhead Panel
Shift + 3
CPT Standard View
Shift + 4
CPT FCP (Autopilot)
Shift + 5
CPT Full Panel (similar to CPT Standard with CDU in view additionally)
Shift + 6
CPT MCDU
Shift + 7
CPT Engine Controls
Shift + 8
CPT Center Console
Shift + 9
MCDU Popup window
Ctrl + Plus
MFD decrease range (CPT)
Ctrl + Minus
MFD increase range (CPT)
Shift + Q
Toggle HUD
Ctrl + W
Toggle Yoke
F10
Overhead Panel (similar to a 2d panel)
F11
FCP (similar to a 2d panel)
F12
MCDU (similar to a 2D panel with PFD/MFD in view)
Ctrl + Shift + 1
Toggle MCDU Keyboard Input (CPT)
Ctrl + Shift + 2
Toggle MCDU Keyboard Input (FO)
Ctrl + Shift + 3
Switch MFD to HSI format
Ctrl + Shift + 4
Switch MFD to NAV format
Ctrl + Shift + 5
Switch MFD to MAP format
Ctrl + Shift + 6
Switch MFD to PLAN format
Ctrl + Shift + 7
Switch MFD to TCAS format
Ctrl + Shift + 8
Switch MFD to WXR format
MCDU KEY INPUT

As soon as you activated MCDU keyboard input (Ctrl + Shift + 1 or +2) you may use your keyboard to enter data
into the keyboard. The following table shows the assignment of key functions and MCDU function.
Function
German Keyboard
U.S. Keyboard
Left MCDU Kybd ON/OFF
Strg + Umschalt + 1
Ctrl + Shift + 1
Right MCDU Kybd ON/OFF
Strg + Umschalt + 2
Ctrl + Shift + 2
LSK 1L
F1
F1
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-23
09-Sep-2015
LSK 2L
F2
F2
LSK 3L
F3
F3
LSK 4L
F4
F4
LSK 5L
F5
F5
LSK 6L
F6
F6
LSK 1R
F7
F7
LSK 2R
F8
F8
LSK 3R
F9
F9
LSK 4R
F10
F10
LSK 5R
F11
F11
LSK 6R
F12
F12
MSG
Strg + F1
Ctrl + F1
Dir/Intc
Strg + F2
Ctrl + F2
Fpln
Strg + F3
Ctrl + F3
Dep/Arr
Strg + F4
Ctrl + F4
Hold
Strg + F5
Ctrl + F5
MCDU Menu
Strg + F6
Ctrl + F6
Index
Strg + F7
Ctrl + F7
Fix
Strg + F8
Ctrl + F8
Legs
Strg + F9
Ctrl + F9
Sec Fpln
Strg + F10
Ctrl + F10
VNAV
Strg + F11
Ctrl + F11
Exec
Return oder Strg + F12
Return or Ctrl + F12
Radio
Umschalt + F1
Shift + F1
Prog
Umschalt + F2
Shift + F2
Perf
Umschalt + F3
Shift + F3
MFD Data
Umschalt + F4
Shift + F4
MFD Menu
Umschalt + F5
Shift + F5
MFD Adv
Umschalt + F6
Shift + F6
A-Z
A-Z
A-Z
0-9
0-9
0-9
SP
Leertaste
Space
DEL
Entf
Delete
CLR
Zurck
Backspace
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-24
09-Sep-2015
ADDITIONAL TOOLS / OPTIONS

Several tools and options are provided to configure the product or to assist you in flight.
SAVING AND LOADING A FLIGHT
When you save a flight using the standard FSX menu option while flying the CRJ, an Aircraft State file will be
created as well. This Aircraft State file contains all the settings that are normally not saved by FSX. When you
load a flight the accompanying Aircraft State file will be loaded so you can continue your flight exactly as you
left off. However this ONLY works if you load a flight using the standard FSX menu and not when you load it via
the Free Flight menu.
USING PANEL STATES
You can also use Aircraft State to configure the aircraft. There are three default Aircraft States:
COLD & DARK: As the aircraft is left

when the last flight of the day is done.
All systems are powered down.
ENG STARTUP: Aircraft configured to
the state just before engines are
started.
ENG RUNNING: Aircraft is configured to
the state where engines have just been
started (you could consider this a
ready for taxi state. Brakes are set and
all lights are set.
It is also possible to create your own states. Just

configure the aircraft as you want and use the
SAVE STATE option after you entered a name.
The name can only be 10 characters (a-z,0-9). In
the image a state Short Final has been saved by the user.
The Aircraft States menu can be reached by pressing the MCDU MENU button on the MCDU. If the aircraft is in
a Cold and Dark state you will have to provide electrical power to the aircraft bus to activate the MCDUs. The
easiest way to do this is to switch on the battery bus (Battery Switch on Overhead to ON) and to use Dave to
provide Ground Power (under the Services option). On the Overhead Electrical panel the AC Available light will
be lit. Press the button to connect it to the aircraft bus.
DAVE
Named after one of the screw members in 2001 Space Oddity (would you believe we are not allowed to call
the thing Hall?). Its a tablet computer mounted on the yoke clipboard..
CHECKLISTS
The checklists (or more precise flows) will assist you in making sure the aircraft is safely operated. Every stage
of the flight is included.
FUEL PLANNER
If you do not want to use the fuel planner you can use Dave to calculate the needed fuel.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-25
09-Sep-2015
V-SPEEDS
Of course the V-Speeds can be calculated and set using the cockpit controls but because that is complex we
included a shortcut option to set V1, Vr, V2 and Vref.
OPTIONS
Diverse options can be set (and saved) in these two pages. Most will be self-explanatory, some guidance on
these:
IRS ALIGN TIME: The inertial reference system uses a system of gyroscopes to measure the movement
of the aircraft. As it knows he starting location it can calculate the current position without any
external references (for example from GPS satellites or radio navigation beacons. To be able to
operate it needs time to spin up and align itself. Depending on conditions this can take quite some
time. The settings here can be used to select realistic time, a compressed time or an instant IRS
aligning.
HELP MESSAGES: Toggles the display of additional EICAS messages. In the CRJ the messages on the
EICAS can be rather cryptic, enabling this option makes then easier to understand. They are always
shown in magenta.
PREPAR3D HDR LIGHTING: When HDR lighting is used in P3D this needs to be activated to make Dave
readable.
SERVICES / MAINTENANCE
WHEEL BLOCKS, GROUND POWER and GROUND AIR option will toggle the display of external objects
but also the actual availability of Ground Power and Ground Air.
AUX DRIVE GEN: When the Auxiliary Drive Generator (known as a Ram Air Turbine in other aircraft) is
deployed it needs to be cranked into stowed position by ground staff.
IDG: The Integrated Drive Generators are engine driven electrical power generating systems. When
you disconnect them in flight they need to be reset by ground staff and this options simulates that.
DOORS
Allows you to open and close the doors and hatches. You can save the configuration so your aircraft will load
with these settings when you load it next.
CRJ MANAGER
You will find the CRJ manager in FSXMainFolder\Aerosoft\Digital Aviation CRJ folder. It allows you to load
passengers and payload and to calculate the fuel load, Center of Gravity and Take-off trim.
Before starting it make sure your simulator is running and your CRJ is the active aircraft on your departure
airport. Also make sure the right aircraft and simulator is selected in the top bar. When all is right a green
Connected should be visible in the top bar.
After you done all calculations you have three options to export the settings to FSX.
Set Fuel & Payload In Flight Simulator: Writes payload and fuel data directly into FSX/FSX-SE/P3D
Save Fuel To Saved Flight File: Writes fuel data into a .FLT or .FXML file (depending on which is
simulator is selected)
Save Payload To Aircraft Configuration: Writes payload data in the aircraft.cfg file
Save Flight Settings: Saves the current payload/fuel settings into a configuration file so CRJ Manager
shows the same data when you start it next time.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-26
09-Sep-2015
LIVERY MANAGER
You will find the livery manager in FSXMainFolder\Aerosoft\Digital Aviation CRJ\Livery Manager Folder.
Installing a livery is as simple as dragging the zip file you downloaded on top of the livery manager. For 90% of
the additional liveries this will work. All other livery ZIP files that meet the following conditions will be handled
automatic (if this method does not work ask the livery designer to be compliant with our standards):
There must be a txt-file ("readme.txt" or different name as long as it's the only txt-file) with the code
snippet for the aircraft.cfg included.
The snippet starts with [FLTSIM.X] and ends with a blank line.
In this snippet the line "ui-type=*aircraft_type*" must be contained, otherwise the manager doesn't
know which plane the livery should be added to.
Each ZIP-file can only contain one livery / alternative versions must be separated into two ZIP files.
The whole file must be a proper ZIP-file containing the file and folder structure on the first level. So do
not zip the folder with the files but only the files themselves.
Beside the text file there needs to be the texture folder with its extension name, containing a
"thumbnail.jpg"
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-27
09-Sep-2015
ROUTE SUGGESTIONS
During preparation of the tutorial we looked into several different routes flown by the CRJ in real life. The
intention was to find a scenic route which is not too short (more stress when climb and descend follow nearly
instantly on to each other) and not too long (overall time it takes to work through the tutorial).
We didnt want all our ideas go to waste and hence include the routes as suggestions for further flights after
going through the tutorial. Alexander Metzger further provided a rather extensive description on one of those
flights, which youll find attached at the end of this section.
So here you go with our route suggestions:
Departure
Arrival
Airline / Flight No
CRJ Type
Hamburg
Copenhagen
Scandinavian
CRJ900
(HAM / EDDH)
(CPH / EKCH)
SK646
09:50
10:40
Copenhagen
Gothenburg
Scandinavian
(CPH / EKCH)
(GOT / ESGG)
SK434
08:10
08:55
Munster-Osnabruck
Frankfurt
Lufthansa
(FMO / EDDG)
(FRA / EDDF)
LH063
06:35
07:25
Dusseldorf
Basel-Mulehouse
Lufthansa / Germanwings
(DUS / EDDL)
(BSL / LFSB)
4U9712
07:10
08:20
Munich
Marseille
Lufthansa
(MUC / EDDM)
(MRS / LFML)
10:45
12:20
LH4362 (meanwhile flown

with ERJ-195
Copenhagen
Aberdeen
Scandinavian
(CPH / EKCH)
(ABZ / EGPD)
SK1521
18:05
18:50
Copenhagen
Berlin Tegel
Scandinavian
(CPH / EKCH)
(TXL / EDDT)
SK0679
15:00
15:55
Copenhagen
Bergen
Scandinavian
(CPH / EKCH)
(BGO / ENBR)
SK2868
14:05
15:25
San Francisco
Jackson Hole
United Airlines
(SFO / KSFO)
(JAC / KJAC)
UA5490
12:50
15:57
Seattle
Santa Barbara
Alaska Airlines
(SEA / KSEA)
(SBA / KSBA)
AS3444
20:15
22:42
CRJ900
CRJ900
CRJ900
CRJ900
CRJ900
CRJ900
CRJ900
CRJ700
CRJ700
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-28
09-Sep-2015
DIGITAL AVIATION CRJ900 FLIGHT FROM DSSELDORF (DUS) TO Basel (BSL)

(by Alexander Metzger)
This is a description of Germanwings flight 4U9712 according the schedule as published on their webpage for
Saturday March 7, 2015. We will be flying one of their Bombardier CRJ900 registered under D-ACNN belonging
to Eurowings which will execute this flight as operator. The planned departure time is 07:00 am and the arrival
should be 70 minutes later at 8:10 am. We will start with our flight planning. You will find a flight situation file
called DA1_DUS-BSL in your flight directory. Have a safe flight!
Please note that we advise you to fly the tutorial flight first as it includes a more detailed
explanation about all systems.
FLIGHT PLANNING
ROUTING
Departure airport: Dsseldorf (IATA: DUS ICAO: EDDL)
Destination airport: Basel (IATA: BSL ICAO: LFSB)
Alternate airport: Zurich (IATA: ZRH ICAO: LSZH)
For European flights, VATroute http://www.vatroute.net/ is a good and simple flight planning page to obtain a
typical route. The query result for EDDL-LFSB at our predicted flight reads like this:
FL196-FL315
MODRU Z283 SUMAS UZ283 RITAX UT27 GTQ UN852 ARPUS
We select flight level 290 (FL290) and the route distance has been calculated to 280 nautical miles (NM). An
additional 20 NM are added to cover departure and arrival routes. As alternate airport we selected Zurich
(LSZH). The distance from LFSB is 45 NM plus 20 NM for the arrival route. We do expect taking off from runway
23L and following the Standard Instrument Departure route (SID) called MODRU 9T.
WEATHER
This is a typical spring morning with refreshing 3 C, light clouds and a moderate, south-easterly wind on
ground.
Based on this data we expect to be taking off from runway 23L. For flight planning we conclude an average
wind component of eleven knots from 032 degrees (11/032) at FL290 and a headwind component of -22 knots
(tailwind) according the weather forecast at cruise altitude.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-29
09-Sep-2015
WEIGHT AND FUEL

For this flight we will be using the following data:
Weight in kg
Weight in pounds
22471 kg
49540 lbs.
72 * 84 = 6048 kg
72 * 185 = 13320 lbs.
Luggage in front compartment
462 kg
1020 lbs.
Cargo in rear compartment
339 kg
748 lbs.
Zero Fuel Weight (ZFW)
29315 kg
64627 lbs.
Weight check against max. ZFW
31752 kg
70000 lbs.
< MZFW OK
Fuel
2700 kg
6000 lbs.
See next page
Take-off weight (TOW)
32015 kg
70672 lbs.
Weight check against max. TOW
37422 kg
82500 lbs.
Dry Operating Weight (DOW)

Passengers: 72 Adult
Comment
< MTOW OK
Detailed calculation for fueling:

Weight in kg
Weight in pounds
32000 kg
70570 lbs.
104 kg (minimum)
230 lbs. (minimum)
Reserve
750 kg
1655 lbs.
Taxi
100 kg
220 lbs.
Minimum fuel
2627 kg
5791 lbs.
Block fuel
2700 kg
6000 lbs.
Distance to destination
340 nm
Take-off weight (TOW)

Flight level to destination
FL290
ISA deviation
-10 C
Headwind component
Contingency
-22 knots
5%
Distance to alternate
45 nm
Flight level to alternate
FL150
Center of Gravity (CoG)

* MAC means Mean Average Chord
22.4% MAC*
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-30
09-Sep-2015
TAKE-OFF DATA
Based on the above determined take-off weight of 31715 kg (69917 lbs.) we will now define the critical
speeds for departure. EDDL runway 23L is long enough (9843 x 148 ft. / 3000 x 45 m) so that there is no
restriction and we can use the speeds from the speed card for 70000 lbs. (31751 kg).
We will be setting flaps to 8 degrees for the take-off and our departure airport altitude is close to sea level.
Outside temperature is less than 10 C. This concludes in the following speed selection:
V1 = 134 knots as maximum speed to abort the take-off.

VR = 135 knots for safe lift-off speed
V2 = 147 knots as safe speed in the case of an engine failure
V2 + 12 = 159 knots as speed for the initial climb phase up to 3000 ft. above aerodrome elevation
(AAE), also used as acceleration altitude
From the same table we also take the speeds for retraction of flaps during the acceleration to initially 210
knots (maximum speed for flaps extended to 8 is 230 kts):
159 knots to retract to position 1

178 knots to retract to position 0
DEPARTURE FROM DUSSELDORF AIRPORT

AIRCRAFT PREPARATION
After completion of the flight preparation it is time to get started. Please load the flight called DA1_DUS-BSL
from the flight menu. You are located at apron position V35 at Dsseldorf airport. It is 5:30 Coordinated
Universal Time (UTC) or 6:30 local time (LT). Our CRJ900 is prepared according to the above described flight
planning with the requested fuel and passenger/freight boarding/loading completed.
Next item as pilot flying (PF) is to finalize cockpit preparation and put the aircraft and the crew into a Request
for start-up and push-back situation.
Programing of Flight Management Systems (FMS)

Our FMS includes a function called Load aircraft state (LOAD STATE), which we will use now to avoid
programing of the FMS and can postpone this learning experience to a later stage. Please load
DA1_DUS from the FCDU Menu.
Check of avionic parameters
o HDG-bug on runway heading
o NAV-CRS on runway heading
o V-Speeds according selection before: 134-135-147-159
o Speed Bug on VT = 159
o ILS-frequency on active runway 23L
o Transponder set to 2-3-5-6 and on standby mode
o Departure route is displayed
o Approved initial flight level 5000 ft. on SID MODRU 9T
o Barometric pressure fine-tuned to airport altitude
o Approved flight plan is complete and active
Check on aircraft
o Fuel according plan
o Hydraulic pumps on - system under pressure
o Elevator trim set according weight and centre of gravity actual set to 6.4 trim units
o All doors closed
o Auxiliary Power Unit (APU) supplies bleed air and current
o Parking brake is set
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-31
09-Sep-2015
o Navigation (NAV) lights and Beacon (BCN) light are on

o Passenger signs Fasten Seatbelts und No Smoking are on
Running Before Start Checklist
o Completed
ENGINE START AND PUS HBACK ON APRON POSITION

The start-up of the engines is executed in a semi-automatic procedure and supervised by the Full Authority
Digital Engine Control (FADEC) system and the pilots.
Throttle lever in CUT OFF position

Press ENG START button typically the right engine first, thereafter the left one
o N2 spooling up to above 20%, check ITT <120C
o Throttle lever into IDLE position
o Kerosene is injected and ignited
o N2 climbing further and N1 to follow
o ITT must be watched Limit is shown in EICAS display
Engine start completed and checked
o N1 stable at 20 to 22%
o Consumption at 250-300 kg/h
o ITT at 400C
o Generators automatically connected and deliver current Check ELEC page
o Ventilation and air conditioning active
Running the After Start Checklist
o Completed
Pushback facing North-East
Pushback completed
Request Taxi Clearance to runway 23L
TAXIING TO RUNWAY 23L

Hint: If you have assigned the front wheel steering via a separate axis assignment on your available hardware
control, this will allow you to steer the CRJ on ground in a realistic way. In addition this will allow you to
execute the flight controls check in a realistic way during taxi time. If you have not, you need to do the check
during standstill.
On the way to the runway you will be setting flaps to position 8 and check the functionality of the controls.
This is done by moving all three control axes to their endpoints and check their movements in the EICAS
display.
The intention to start moving is acknowledged by turning on the TAXI LIGHT. The CRJ starts rolling with just a
bit of power to overcome the inertia and can easily be controlled. If light on weight it may be necessary to
softly brake to avoid exceeding speed limits. Typically 7 to 10 kts are used on apron areas and 20 to 30 kts on a
free taxiway. This depends very much on weather, taxiway conditions and other traffic. And any instructions
from ground control.
Before reaching the holding point of the departure runway the Taxi Checklist must be completed and only
when everything is normal you signal your readiness by switching the transponder code to ON. Some airports
do request to be ON when rolling on the Apron but latest at lining up on departure runway.
TAKE-OFF ON RWY 23L
After having received clearance to Line up and wait, the last preparations for the take-off need to be made:
Alert the flight attendants "Cabin crew prepare for take-off"
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-32
09-Sep-2015
Check identical values for HDG-bug and runway direction should be 232
Running Before Take-off Checklist
o Completed
After having received clearance for taking off you switch on the landing lights and by that signals to the tower
that the take-off is imminent. First move the throttles forward to achieve about 70% N1 and check that both
engines are very close N1%. By that you assure that both engines are delivering similar thrust. Only then you
guide the throttles beyond CLB-dent into the TOGA-dent and monitor that the target N1% is matched while ITT
temperature limit is not exceeded. Any malfunction leads to immediate take-off abortion by the pilot in
charge.
Background information:
Taking off in an aircraft is a relative strict process serving safety of flight and noise abatement procedures. You
may divide into the take-off run up to V1, the rotation at VR and the initial climb at minimum V2 + 10. All these
V-Speeds have been defined during flight preparation as per earlier chapters. See previous chapter of this
tutorial.
Rotation at VR shall not exceed 3 degree/second, so that the tail will not touch the ground (tail strike). Pitch
attitude will be set to 15 to 18 and the trim may be adjusted to match and the gear will be retracted. By that
an optimal rate of climb with a built in safety margin in case of engine failure and minimal speed can be
achieved.
At 1500 ft. above aerodrome elevation (AAE) engine power is reduced for noise abatement.
At 3000 ft. above AAE the acceleration towards the maximum allowed speed of 250 kts will be initiated. This is
executed by an aligned process of flaps lift and flaps drag reduction with synchronous reduction of engine
power and climb rate to achieve the desired acceleration. You may control the aircraft manually or let the
autopilot have the controls.
REGULAR TAKE-OFF SEQUENCE (WITHOUT SPEED LIMIT ON DEPARTURE ROUTE) FOR THIS FLIGHT:
1.
2.
3.
Positive rate of climb

400 ft.
600 ft.
4.
5.
6.
7.
8.
9.
1500 ft.
3000 ft.
> 159 kts
> 178 kts
Flaps are 0
Climb Check
Gear retraction and maintain V2+10 as minimum.

HDG or NAV to be activated
Activate autopilot with active HDG or NAV mode
IAS HOLD mode to be engaged current speed will be set as target
Pull back throttles to CLB dent and keep minimum V2 + 10
Target speed set to 210 kts (maximum speed for flaps 8)
Flaps retraction to position 1
Flaps retraction to position 0
Target speed set to 250 kts (maximum speed <FL100)
After Take-off Checklist to be completed
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-33
09-Sep-2015
CLIMB AND CRUISE

After the busy phase is over and the autopilot follows the horizontal navigation, the route, it is our turn to
secure that all marked speed and altitude restrictions will be followed. We also change to standard barometric
pressure at the transition Altitude (TA) on the MODRU 9T departure route this is at 5000 ft.
Background information: Different to flying in the US, the European altitude control requires changing at
3000 to 5000ft and in mountainous areas higher to meet minimum altitudes above terrain. As of that TL the
flight level will be assigned as FL50 equal to 5000 ft. at standard barometric pressure 1013 mbar (29.92 in HG)
and mentioned by the controller.
The CRJ has no automatic vertical navigation control and it is the task of the pilot flying to concur with possible
restrictions by setting i.e. the next allowed flight level. Our SID includes the following description and
limitations:
MODRU NINE TANGO
On track 232 DY to 3.4 DME DUS/3.6 DME IDNE;
RT, on track 320 to UBORO (_);
LT, on track 199 via NETEX (_) to MODRU(_).
Climb with 7% (425ft/NM) or more until passing 3000.
GPS/FMS RNAV: [A600+] - DL243[K210-; R] |UBORO[L] - NETEX[K250-] - MODRU[F210+].
With the following meaning:
NETEX[K210-] the speed until NETEX is limited to 210 kts, even if you may have exceeded FL100
MODRU[F210+] means that we should be crossing MODRU at FL210 or higher
Background information: Yet the CRJ has a built in autopilot modus that can control the climb or descent
speed by changing the pitch attitude and by that the rate of climb or descent to match a given target speed.
For best performance, thrust lever need to be at least in CLB and the FADEC will set an optimal climb power
according a database that relates to altitude and outside temperature. The typically used speed profile is
250/290/0.74 and this profile is the base for our flight calculation. Alternatively you may choose to fly faster,
i.e. catch up with a delay. This would be 250/300/0.77 or even 250/320/0.80. Naturally both are less
economical.
The first number in this list of speeds is the speed below FL100, which is unified around the world but maybe
lifted by the controller, if current traffic allows.
The second number is the speed for climb and cruise above FL100. With increased flight altitude, there is a
limit for aircraft not only from indicated Airspeed but also from the Mach number that shall not be
exceeded. The mentioned speed profiles keep a safety margin from these structural limits of the aircraft. At
about FL270, you reach an interception of IAS =290 and Mach =0.74 and you need to follow the speed control
by Mach. The speed selection button has a center push button to switch between IAS and Mach.
Passing FL100 we switch off the landing lights and could change the IAS HOLD to the desired 290 kts for the
following climb to FL290. But since the SID contains a speed restriction of maximum 250 kts until waypoint
NETEX, we need to wait until we have that passed. Since our weather is not predicting any special turbulence,
we switch off the Fasten Seat Belt sign.
Just before we reach FL290 we are matching up with Mach 0.74 and change to Mach speed control.
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-34
09-Sep-2015
At 1000 ft. prior to target FL an alert will draw our attention to monitor the levelling off to horizontal cruise
flight. Since this requires less power from the engines, we need to pull out the thrust lever and adjust the N1
manually so that the speed stays at Mach 0.74. From experience we know that the expected N1 is about 81 to
82 % and we adjust to keep a speed of Mach 0.74 consistently.
Cruising is the quietest flight chapter and except for scanning other traffic and ATC handover we just monitor
engine parameters and climate control.
ARRIVAL TO BASEL AIRPORT
DECENT AND ENTRY INTO AIRPORT SPACE
The descent to our destination airport has two distinctive parts. First part is the descent into lower airspace
with the reduction of speed down to 250 knots below FL100. Thereafter follows the arrival according to the
published Standard Arrival Route (STAR) or according vectors given by the approach controller. We follow the
process flying the STAR route which needs to be selected first.
Slight winds from southeast suggest that runway 15 is in use. The approach will be done following the
Instrument Landing System (ILS) starting at the Initial Approach Fix (IAF) called ALTIK at 5500 ft. This is linked
to our last waypoint by the STAR called ARPUS8K. Now the route to our landing runway is defined.
Background information: The arrival to the destination airport will be explained by the pilot flying (PF) in great
detail during the approach briefing. The Pilot Monitoring (PM) is checking the process. Every step will be
indicated and any specialties will be clarified. This may cover speed restriction and minimum altitudes,
obstacles and noise abatement requirements. Further the setup of the navigation instruments like VORs (VHF
Omnidirectional Range) in both NAV devices and in the ADF (Automatic Direction Finder), if an NDB (NonDirectional Bearing) is available. Final item is the process to execute a missed approach, stating the route
which typically ends at a holding at a waypoint, from which a new approach can be executed.
Route preparation:
ILS Y RWY 15 with IAF ALTIK at minimum 5500 ft.

12 DME Arc BLM with frequency 117.45 set in VOR2
ILS with frequency 111.55, identifier MH set in VOR1 and course 154
Threshold elevation 864 ft. entered as LDG ELEV
Missed Approach straight ahead crossing ADF BS 376 set, followed by a right turn with maximum 220
knots intercepting BLM outbound radial 230. Thereafter 15 DME Arc BLM to ALTIK hold
Landing configuration flaps 45 und VRef=136 kts
o Weather classification for ILS. In use are CAT I, CAT II, CAT IIIa to CAT IIIc with lowering safety
altitudes and visibility requirements to initiate the missed approach procedure.
DESCENT CHECK
Entry into airport space:
> 10000 ft. > Setting target speed to 250 kts (maximum speed <FL100) and reducing accordingly
10000 ft > Landing lights on
15 min before landing > Passenger signs on
7 min before landing > Cabin crew information Cabin crew prepare for landing
6000 ft. > Actual barometric pressure set in all altimeters
Approach Check > Running Approach Checklist
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-35
09-Sep-2015
Basel airport is located in the 3 country triangle of France, Germany and Switzerland with the cities of
Mulhouse and Basel and the Jura mountains in the south. Due to this location, the arrival route is quite
complex. Adhering to altitude minimum 4000 ft. and a speed of maximum 185 kts, because of tight turns on
the entry to the DME (Distance Measurement Equipment) arc and the final 90 turn on ILS localizer (LOC),
requires a good control of the aircraft. As a consequence you need to reduce speed to 200 kts and flaps 1 and
185 kts with flaps 8 is necessary.
A more simple arrival can be done by using vectors, i.e. outbound VOR/DME GROSTENQUIN GTQ 111.25 MHz
set in NAV1 and descending to 4000 ft. at 10.4 NM before VOR/DME Basel MULHOUSE BLM 117.45 MHz set in
NAV2 and once close to BLM switch to standby ILS/DME MH 111.55 MHz on NAV 1.
FINAL APPROACH DIREC TION RWY 15
The required 185 kts at 4000 ft. should be flown with flaps 8. We capture the glideslope at 9.5 NM distance
and 3100 ft. altitude difference to the runway. Remaining are about 3 min to achieve landing configuration.
We therefore reduce to 160 kts and flaps 20. 5NM before threshold we drop the gear and reduce speed
further. Consequently flaps 35 and 45 are set so that we achieve landing configuration at 1000 ft. above
runway elevation and the speed should read VRef + 10 = 146 kts. Typically you need about 58% N1 power.
Running the Before Landing Checklists and switching off the autopilot we are cleared to land.
LANDING
During the last 1000 ft. we are concentrated on keeping the speed and the correct position in reference to the
flight director (FD) indication. If the deviation from the ILS LOC/GS happens to be more that 1 dot, the landing
must be aborted and the above discussed Missed Approach Procedure (MAP) must be executed.
Crosswind influences must be equalized precisely and with strong headwinds the value for Vref needs to be
increased by half the headwind. This is done to increase the safety margin.
At 50 ft. above runway well indicated at the RA display we pull the thrust lever to idle and reduce the
vertical speed with a soft pull on the yoke. Once the main wheels have touched the ground, the spoilers are
automatically deployed and the pilot pulls the throttle into reverse position. Drop the nose softly to get the
front wheel on ground and only then use wheel brakes for further speed reduction. At 90 kts you cut reversers
by setting the throttle lever back to idle position and take the next exit left to your parking position.
Crossing the hold line you configure the aircraft for taxiing to position:
Landing lights to off, taxi light remains on

Strobes to off
Flaps to be retracted
Transponder set on Standby
Probes heat to off
Depending on gate or apron position and local prescription we may switch on the APU to assure air
conditioning and electric supplies once we switch off the engines
Turning into position we switch off the taxi lights (danger of blinding ground personnel)
PARKING AND SECURING THE AIRCRAFT

After arrival at the parking position:
Parking brakes set to on

Cut the engines
Fuel pumps switched off
Seatbelt signs switched off
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-36
09-Sep-2015
NAV lights stay typically on

Beacon set to off
Nose wheel steering to off
De-boarding of passengers and recording of flight data

DISCLAIMER
All statements and explanations given in this flight description are meant as introduction to execute a flight
with the add-on CRJ700 and &CRJ900 developed by Digital Aviation for Aerosoft and to be used with the
flight simulators FSX (Microsoft) or Prepar3D (Lockheed Martin).
This is not a training material for real world flying!
The comments represent my knowledge as add-on aircraft developer without a respective pilot license. The
shown screen shots are made from programs that I use for my personal simulator flying.
Alexander M. Metzger, Geneva, March 2015
EXTENDED FLIGHT PLAN EDDL-LFSB (SOURCE VATROUTE)
CRJ-700 CRJ-900
AOM PART 1
VOL
1-1-37
09-Sep-2015
EXTENDED FLIGHT PLAN EDDL-LFSB (SOURCE AIVLASOFT EFB)

Vol1 AOM Part1

Uploaded by

Copyright:

Available Formats

Vol1 AOM Part1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vol1 AOM Part1

Uploaded by

Copyright:

Available Formats

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Pre Release Candidate

Adding Manager details

Spellchecked and many small things changed

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Hans Hartmann (Digital Aviation)

INSTALLING & REMOVING

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Reboot your computer

Reboot your computer

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

CRJ Support Forums: http://forum.aerosoft.com/index.php?/forum/747-crj-700900/

The release version number will be 1.00.

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Dry Operating Weight

Maximum zero fuel

Maximum Ramp Weight

Maximum landing weight

Maximum Seat Capability

Max. Cruise Speed

Takeoff field length

Landing field length

PILOT INFORMATION FOR TRANSITIONING TO THE BOMBARDIER CRJ700 AND 900

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

THE CRJ IN FLIGHTSIM

THE VIRTUAL COCKPIT OVERVIEW

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

3. Centre Instrument Panel

4. Captain Instrument Panel

5. Captain Side Panel/Side console

6. First Officer Instrument Panel

7. First Officer Side Panel/Side

Aerosoft Digital Aviation

AIRCRAFT GENERAL / IN FSX

2. Fire Detection Test System

3. Hydraulic Shutoff Valves (SOV)

4. Externa Lighting Controls

7. Auxiliary Power Unit Controls

8. Engine Start Panel

10. Emergency Locator Transmitter

11. Cabin Pressure Controls

12. Air Conditioning Controls

13. Anti-Ice Controls