ASTM D7136 Low Velocity Impact

Designation: D7136/D7136M 12
Standard Test Method for
Measuring the Damage Resistance of a Fiber-Reinforced

Polymer Matrix Composite to a Drop-Weight Impact Event1
1. Scope
1.1 This test method determines the damage resistance of
multidirectional polymer matrix composite laminated plates
subjected to a drop-weight impact event. The composite
material forms are limited to continuous-fiber reinforced polymer matrix composites, with the range of acceptable test
laminates and thicknesses defined in 8.2.
1.1.1 Instructions for modifying these procedures to determine damage resistance properties of sandwich constructions
are provided in Practice D7766/D7766M.
1.2 A flat, rectangular composite plate is subjected to an
out-of-plane, concentrated impact using a drop-weight device
with a hemispherical impactor. The potential energy of the
drop-weight, as defined by the mass and drop height of the
impactor, is specified prior to test. Equipment and procedures
are provided for optional measurement of contact force and
velocity during the impact event. The damage resistance is
quantified in terms of the resulting size and type of damage in
the specimen.
1.3 The test method may be used to screen materials for
damage resistance, or to inflict damage into a specimen for
subsequent damage tolerance testing. When the impacted plate
is tested in accordance with Test Method D7137/D7137M, the
overall test sequence is commonly referred to as the Compression After Impact (CAI) method. Quasi-static indentation per
Test Method D6264/D6264M may be used as an alternate
method of creating damage from an out-of-plane force and
measuring damage resistance properties.
1.4 The damage resistance properties generated by this test
method are highly dependent upon several factors, which
include specimen geometry, layup, impactor geometry, impactor mass, impact force, impact energy, and boundary conditions. Thus, results are generally not scalable to other configurations, and are particular to the combination of geometric and
physical conditions tested.
1.5 The values stated in either SI units or inch-pound units
are to be regarded separately as standard. The values stated in
1
This test method is under the jurisdiction of ASTM Committee D30 on
Composite Materials and is the direct responsibility of Subcommittee D30.05 on
Structural Test Methods.
Current edition approved April 1, 2012. Published May 2012. Originally
approved in 2005. Last previous edition approved in 2007 as D7136/D7136M - 07.
DOI: 10.1520/D7136_D7136M-12.
each system may not be exact equivalents; therefore, each

system shall be used independently of the other. Combining
values from the two systems may result in non-conformance
with the standard.
1.5.1 Within the text the inch-pound units are shown in
brackets.
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2.1 ASTM Standards:2
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D883 Terminology Relating to Plastics
D3771 Specification for Rubber Seals Used in Concentrating Solar Collectors
D3763 Test Method for High Speed Puncture Properties of
Plastics Using Load and Displacement Sensors
D3878 Terminology for Composite Materials
D5229/D5229M Test Method for Moisture Absorption
Properties and Equilibrium Conditioning of Polymer Matrix Composite Materials
D5678 Test Method for Freeze/Thaw Resistance of Wax
Emulsion Floor Polish
D6264/D6264M Test Method for Measuring the Damage
Resistance of a Fiber-Reinforced Polymer-Matrix Composite to a Concentrated Quasi-Static Indentation Force
D7137/D7137M Test Method for Compressive Residual
Strength Properties of Damaged Polymer Matrix Composite Plates
D7766/D7766M Practice for Damage Resistance Testing of
Sandwich Constructions
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
E18 Test Methods for Rockwell Hardness of Metallic Materials
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.
Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Copyright ASTM International

Provided by IHS under license with ASTM
No reproduction or networking permitted without license from IHS
1Licensee=Universita Bologna - related to 5972936/5935522001

Not for Resale, 11/08/2013 10:40:10 MST
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
This standard is issued under the fixed designation D7136/D7136M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.
D7136/D7136M 12
E122 Practice for Calculating Sample Size to Estimate,
With Specified Precision, the Average for a Characteristic
of a Lot or Process
E177 Practice for Use of the Terms Precision and Bias in
ASTM Test Methods
E456 Terminology Relating to Quality and Statistics
E1309 Guide for Identification of Fiber-Reinforced
Polymer-Matrix Composite Materials in Databases
E1434 Guide for Recording Mechanical Test Data of FiberReinforced Composite Materials in Databases
E2533 Guide for Nondestructive Testing of Polymer Matrix
Composites Used in Aerospace Applications
2.2 Military Standards:
MIL-HDBK-17-3F Composite Materials Handbook, Volume 3Polymer Matrix Composites Materials Usage,
Design and Analysis3
MIL-HDBK-728/1 Nondestructive Testing4
MIL-HDBK-731A Nondestructive Testing Methods of
Composite MaterialsThermography4
Composite MaterialsAcoustic Emission4
Composite MaterialsRadiography4
Composite MaterialsUltrasonics4
NASA Reference Publication 1092 Standard Tests for
Toughened Resin Composites, Revised Edition, July
19835
3. Terminology
3.1 DefinitionsTerminology D3878 defines terms relating
to composite materials. Terminology D883 defines terms
relating to plastics. Terminology E6 defines terms relating to
mechanical testing. Terminology E456 and Practice E177
define terms relating to statistics. In the event of a conflict
between terms, Terminology D3878 shall have precedence
over the other standards.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 If the term represents a physical quantity, its analytical
dimensions are stated immediately following the term (or letter
symbol) in fundamental dimension form, using the following
ASTM standard symbology for fundamental dimensions,
shown within square brackets: [M] for mass, [L] for length, [T]
for time, [u] for thermodynamic temperature, and [nd] for
non-dimensional quantities. Use of these symbols is restricted
to analytical dimensions when used with square brackets, as
the symbols may have other definitions when used without the
brackets.
3.2.2 dent depth, d [L], nresidual depth of the depression
formed by an impactor after the impact event. The dent depth
shall be defined as the maximum distance in a direction normal
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
3
Available from U.S. Army Research Laboratory, Materials Directorate, Aberdeen Proving Ground, MD 21001.
4
Available from U.S. Army Materials Technology Laboratory, Watertown, MA
02471.
5
Available from National Aeronautics and Space Administration (NASA)Langley Research Center, Hampton, VA 23681-2199.

to the face of the specimen from the lowest point in the dent to
the plane of the impacted surface that is undisturbed by the
dent.
3.2.3 nominal value, na value, existing in name only,
assigned to a measurable property for the purpose of convenient designation. Tolerances may be applied to a nominal
value to define an acceptable range for the property.
3.2.4 principal material coordinate system, na coordinate
system with axes that are normal to the planes of symmetry
inherent to a material.
3.2.4.1 DiscussionCommon usage, at least for Cartesian
axes (123, xyz, and so forth), generally assigns the coordinate
system axes to the normal directions of planes of symmetry in
order that the highest property value in a normal direction (for
elastic properties, the axis of greatest stiffness) would be 1 or
x, and the lowest (if applicable) would be 3 or z. Anisotropic
materials do not have a principal material coordinate system
due to the total lack of symmetry, while, for isotropic materials,
any coordinate system is a principal material coordinate
system. In laminated composites, the principal material coordinate system has meaning only with respect to an individual
orthotropic lamina. The related term for laminated composites
is reference coordinate system.
3.2.5 recorded contact force, F [MLT-2], nthe force exerted by the impactor on the specimen during the impact event,
as recorded by a force indicator.
3.2.6 reference coordinate system, na coordinate system
for laminated composites used to define ply orientations. One
of the reference coordinate system axes (normally the Cartesian x-axis) is designated the reference axis, assigned a
position, and the ply principal axis of each ply in the laminate
is referenced relative to the reference axis to define the ply
orientation for that ply.
3.2.7 striker tip, nthe portion or component of the impactor which comes into contact with the test specimen first during
the impact event.
3.3 Symbols:
A = cross-sectional area of a specimen
CE = specified ratio of impact energy to specimen thickness
CV = coefficient of variation statistic of a sample population
for a given property (in percent)
D = damage diameter (see Fig. 11)
d = dent depth
E = potential energy of impactor prior to drop
E1 = absorbed energy at the time at which force versus time
curve has a discontinuity in force or slope
Ea = energy absorbed by the specimen during the impact
event
Ei = actual impact energy (incident kinetic energy)
Emax = absorbed energy at the time of maximum recorded
contact force
F = recorded contact force
F1 = recorded contact force at which the force versus time
curve has a discontinuity in force or slope
Fmax = maximum recorded contact force
g = acceleration due to gravity
h = specimen thickness
H = impactor drop height
D7136/D7136M 12
NOTEClamp tip centered 0.25 in. from edge of cut-out.

FIG. 1 Impact Support Fixture (Inch-Pound Version)
NOTEClamp tip centered 6 mm from edge of cut-out.

FIG. 2 Impact Support Fixture (SI Version)
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
l = specimen length
m = impactor mass
md = impactor mass for drop height calculation
mdlbm = impactor mass in standard gravity for drop height
calculation
n = number of specimens per sample population
N = number of plies in laminate under test
Sn-1 = standard deviation statistic of a sample population for
a given property
t = time during impactor drop and impact event
ti = time of initial contact
tT = contact duration (total duration of the impact event)
w = specimen width
v = impactor velocity
vi = impactor velocity at time of initial contact, ti
W12 = distance between leading edges of the two flag prongs
on velocity indicator
xi = test result for an individual specimen from the sample
population for a given property
x = mean or average (estimate of mean) of a sample population for a given property

d = impactor displacement
4. Summary of Test Method
4.1 A drop-weight impact test is performed using a balanced, symmetric laminated plate. Damage is imparted through
out-of-plane, concentrated impact (perpendicular to the plane
of the laminated plate) using a drop weight with a hemispherical striker tip. The damage resistance is quantified in terms of
the resulting size and type of damage in the specimen. The
damage response is a function of the test configuration;
comparisons cannot be made between materials unless identical test configurations, test conditions, and so forth are used.
4.2 Optional procedures for recording impact velocity and
applied contact force versus time history data are provided.
4.3 Preferred damage states resulting from the impact are
located in the center of the plate, sufficiently far from the plate
D7136/D7136M 12
FIG. 3 Representative Rigid Base (Inch-Pound Version)
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
FIG. 4 Representative Rigid Base (SI Version)
edges such that the local states of stress at the edges and at the
impact location do not interact during the damage formation
event.
5. Significance and Use
5.1 Susceptibility to damage from concentrated out-of-plane
impact forces is one of the major design concerns of many
structures made of advanced composite laminates. Knowledge
of the damage resistance properties of a laminated composite
plate is useful for product development and material selection.

5.2 Drop-weight impact testing can serve the following

purposes:
5.2.1 To establish quantitatively the effects of stacking
sequence, fiber surface treatment, variations in fiber volume
fraction, and processing and environmental variables on the
damage resistance of a particular composite laminate to a
concentrated drop-weight impact force or energy.
5.2.2 To compare quantitatively the relative values of the
damage resistance parameters for composite materials with
different constituents. The damage response parameters can

FIG. 5 Impact Device with Cylindrical Tube Impactor Guide Mechanism
FIG. 6 Impact Device with Double Column Impactor Guide Mechanism
include dent depth, damage dimensions, and through-thickness

locations, F1, Fmax, E1 and Emax, as well as the force versus
time curve.

5.2.3 To impart damage in a specimen for subsequent

damage tolerance tests, such as Test Method D7137/D7137M.

--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
D7136/D7136M 12
D7136/D7136M 12
FIG. 7 Drop-Weight Impact Test Specimen (Inch-Pound Version)
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
FIG. 8 Drop-Weight Impact Test Specimen (SI Version)
5.3 The properties obtained using this test method can

provide guidance in regard to the anticipated damage resistance
capability of composite structures of similar material, thickCopyright ASTM International
ness, stacking sequence, and so forth. However, it must be

understood that the damage resistance of a composite structure
is highly dependent upon several factors including geometry,
D7136/D7136M 12
FIG. 9 Representative Impactor Force versus Time History
FIG. 10 Impactor Force versus Time History with Harmonic Resonance
thickness, stiffness, mass, support conditions, and so forth.

Significant differences in the relationships between impact
force/energy and the resultant damage state can result due to
differences in these parameters. For example, properties obtained using this test method would more likely reflect the
damage resistance characteristics of an unstiffened monolithic

skin or web than that of a skin attached to substructure which
resists out-of-plane deformation. Similarly, test specimen properties would be expected to be similar to those of a panel with
equivalent length and width dimensions, in comparison to
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---


D7136/D7136M 12
FIG. 11 Measurement of Extent of Damage
those of a panel significantly larger than the test specimen,

which tends to divert a greater proportion of the impact energy
into elastic deformation.
5.4 The standard impactor geometry has a blunt, hemispherical striker tip. Historically, for the standard laminate
configuration and impact energy, this impactor geometry has
generated a larger amount of internal damage for a given
amount of external damage, when compared with that observed
for similar impacts using sharp striker tips. Alternative impactors may be appropriate depending upon the damage resistance
characteristics being examined. For example, the use of sharp
striker tip geometries may be appropriate for certain damage
visibility and penetration resistance assessments.
5.5 The standard test utilizes a constant impact energy
normalized by specimen thickness, as defined in 11.7.1. Some
testing organizations may desire to use this test method in
conjunction with D7137/D7137M to assess the compressive
residual strength of specimens containing a specific damage
state, such as a defined dent depth, damage geometry, and so
forth. In this case, the testing organization should subject
several specimens, or a large panel, to multiple low velocity
impacts at various impact energy levels using this test method.
A relationship between impact energy and the desired damage
parameter can then be developed. Subsequent drop weight
impact and compressive residual strength tests can then be

performed using specimens impacted at an interpolated energy
level that is expected to produce the desired damage state.
6. Interferences
6.1 The response of a laminated plate specimen to out-ofplane drop-weight impact is dependent upon many factors,
such as laminate thickness, ply thickness, stacking sequence,
environment, geometry, impactor mass, striker tip geometry,
impact velocity, impact energy, and boundary conditions.
Consequently, comparisons cannot be made between materials
unless identical test configurations, test conditions, and laminate configurations are used. Therefore, all deviations from the
standard test configuration shall be reported in the results.
6.2 Material and Specimen PreparationPoor material
fabrication practices, lack of control of fiber alignment, and
damage induced by improper specimen machining are known
causes of high material data scatter in composites in general.
Important aspects of plate specimen preparation that contribute
to data scatter include thickness variation, out-of-plane curvature, surface roughness, and failure to maintain the dimensions
specified in 8.2.
6.3 Specimen Geometry and Impact LocationThe size,
shape, thickness, and stacking sequence of the plate, along with
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---


D7136/D7136M 12
the impact location, can affect the impact deformation and

damage formation behavior of the specimens significantly. The
degree of laminate orthotropy can strongly affect the damage
formation. Results can be affected if the impact force is not
applied perpendicular to the plane of the laminated plate.
6.4 Support Fixture CharacteristicsResults are affected
by the support fixture cut-out dimensions, material, fixture
bending rigidity, and the rigidity of the surface that the support
fixture is located upon. The location of the clamps, clamp
geometry, and the clamping force can affect the deformation of
the specimen during impact.
6.5 Impact Device CharacteristicsResults are affected by
the rigidity of the impact device, friction between the impactor
and guide(s) during the drop, impactor geometry, and impactor
mass. Errors can result if the test specimen and specimen
support fixture are not centered with respect to the impact
device.
6.6 Force OscillationsForce versus time histories typically contain many oscillations which may be introduced by
two primary sources. The first source is the natural frequency
(or frequencies) of the impactor, and is often referred to as
impactor ringing. The ringing may be more severe if the
impactor components are not rigidly attached. The second
source of force oscillations is the flexural vibration of the
impacted specimen. The ringing oscillations generally occur
at higher frequencies than the oscillations generated by the
specimen. The high-frequency ringing oscillations do not
typically represent an actual force transmitted to the specimen.
However, the oscillations caused by specimen motion are
actual forces applied to the specimen and should not be filtered

or smoothed. For both sources, the oscillations are typically
excited during initial contact and during damage formation.
For further definition and examples of force oscillatons, refer
to Appendix X1 of Test Method D3763.
6.7 Impact VariablesResults are affected by differences in
the drop height, impact velocity, and impact energy. Results are
also affected by wave propagation and vibrations in the
specimen, impactor, impact device and support fixture during
the impact event.
6.8 Non-Destructive InspectionNon-destructive inspection (NDI) results are affected by the particular method
utilized, the inherent variability of the NDI method, the
experience of the operator, and so forth.
6.9 Force F1 and absorbed energy E1 do not physically
represent the initiation of damage, as sub-critical matrix cracks
and small delaminations may initiate at lower force and energy
values. Rather, F1 and E1 represent the initial value of force
and energy at which a change in the stiffness characteristics of
the specimen can be detected, respectively.
6.10 The dent depth may relax or reduce with time or
upon exposure to different environmental conditions.
6.11 Non-laminated, 3-D fiber-reinforced composites may
form damage through different mechanisms than laminates.
7. Apparatus
7.1 Micrometers and CalipersThe micrometer(s) shall be
used for specimen length, width and thickness measurements,
and shall use a 4 to 6 mm [0.16 to 0.25 in.] nominal diameter
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
FIG. 12 Commonly Observed Damage Modes from Out-of-Plane Drop-Weight Impact
D7136/D7136M 12
ball-interface on irregular surfaces such as the bag-side of a
laminate, and a flat anvil interface on machined edges or very
smooth tooled surfaces. A caliper of suitable size shall be used
for measurement of dimensions for detected damage. The
accuracy of the instruments shall be suitable for reading to
within 1 % of the specimen width and thickness. For typical
specimen geometries, an instrument with an accuracy of
60.0025 mm [60.0001 in.] or better is desirable for thickness
measurement, while an instrument with an accuracy of 60.025
mm [60.001 in.] or better is desirable for length, width, and
damage dimension measurement.
NOTE 1Calipers may be used for specimen length and width measurements if the specimen is not intended to undergo subsequent compression residual strength testing in accordance with Test Method D7137/
D7137M. For specimens intended to undergo subsequent residual strength
testing, specimen length and width measurements shall use micrometers to
ensure consistent measurement accuracy for both test methods.
7.2 Support FixtureThe impact support fixture, shown in

Figs. 1 and 2, shall utilize a plate at least 20 mm [0.75 in.] thick
constructed from either aluminum or steel. The cut-out in the
plate shall be 75 6 1 mm by 125 6 1 mm [3.0 6 0.05 in. by
5.0 6 0.05 in.]. The face of the plate shall be flat to within 0.1
mm [0.005 in.] in the area which contacts the test specimen.
Guiding pins shall be located such that the specimen shall be
centrally positioned over the cut-out. Four clamps shall be used
to restrain the specimen during impact. The clamps shall have
a minimum holding capacity of 1100 N (200 lbf). The tips of
the clamps shall be made of neoprene rubber with a durometer
of 70-80 Shore A. The fixture shall be aligned to a rigid base
using bolts or clamps; a representative base design is shown in
Figs. 3 and 4.
NOTE 2When impacted with the standard impactor (defined in 7.3.1)
at the standard energy level defined in 11.7.1, the standard specimen has
historically developed damage sizes less than half of the unsupported
specimen width (38 mm [1.5 in.]). Should the expected damage area
exceed this size (such as in studies for barely visible impact damage, for
example), it is recommended to examine alternative specimen and fixture
designs, such as NASA 1092, which are larger and can accommodate
larger damage areas without significant interaction from edge support
conditions.
7.3 Impact DeviceRepresentative drop-weight impact

testing devices are shown in Figs. 5 and 6. At a minimum, the
impact device shall include a rigid base, a drop-weight impactor, a rebound catcher and a guide mechanism. The rebound
catcher is typically an inertially activated latch that trips upon
the initial impact, then catches the impactor on a stop during its
second decent. The rebound catcher must not affect the motion
of the impactor until after the impactor has lost contact with the
specimen after the initial impact. If such equipment is unavailable, rebound hits may be prevented by sliding a piece of rigid
material (wood, metal, and so forth) between the impactor and
specimen, after the impactor rebounds from the specimen
surface after impact. More complex devices may include
latching and hoist mechanisms, stop blocks or shock absorbers,
and instrumentation for determining impactor velocity and
impact force. The use of velocity and force instrumentation is
recommended to provide additional information about the
impact event, but is not required.
7.3.1 ImpactorThe impactor shall have a mass of 5.5 6

0.25 kg [12 6 0.5 lbm], and shall have a smooth hemispherical
striker tip with a diameter of 16 6 0.1 mm [0.625 6 0.005 in.]
and a hardness of 60 to 62 HRC as specified in Test Methods
E18. Alternative impactors may be used to study relationships
between visible damage geometry (e.g., dent depth, dent
diameter) and the internal damage state. If a different impactor
is used as part of the testing, the shape, dimensions and mass
shall be noted and the results reported as non-standard.
NOTE 3If the desired impact energy level cannot be achieved using
the standard impactor mass dropped from a height of at least 300 mm [12
in.], an impactor with a mass of 2.0 6 0.25 kg [4 6 0.5 lbm] shall be used
instead.
7.3.2 Guide MechanismHistorical guide mechanisms include single cylindrical tubes through which a cylindrical
impactor travels (Fig. 5), as well as double-column guides for
a crosshead-mounted impactor (Fig. 6). The height of the guide
mechanism shall be sufficient to permit drop-weight testing for
the impact desired energy level. For cylindrical drop tubes, the
clearance between the impactor and tube inner diameter should
not exceed 1 mm [0.03 in.]. Details of the guide mechanism
geometry shall be noted. In all respects, guide friction shall be
negligible; otherwise, velocity measurements shall be required
and impact energy calculations shall be based upon the
measured velocity (Eq 4).
7.3.3 Force IndicatorIf utilized, the force indicator shall
be in conformance with Practices E4 and Test Method D3763,
and shall be capable of indicating the impact force imparted to
the test specimen. This device shall be essentially free from
inertia-lag at the predicted impact velocity and shall indicate
the force with an accuracy over the force range(s) of interest to
within 61 % of the indicated value. The force indicator shall
be positioned such that at least 95 % of the impactor mass is
located above it; the error in the force reading increases as the
percentage of mass located above the load cell decreases.
7.3.4 Velocity IndicatorThe impact device may be instrumented to measure the velocity of the impactor at a given point
before impact, such that the impact velocity may be calculated.
Commonly, such systems use a double-pronged flag, which
obstruct a light beam between a photo-diode emitter and
detector. The leading edges of the flag prongs are typically
separated by 3.0 to 10.0 mm [0.125 to 0.400 in.]. The flag
prongs shall be positioned such that velocity measurement is
completed between 3 to 6 mm [0.13 to 0.25 in.] vertically
above the surface of the specimen. The impact velocity is
calculated using the measured time the light beam is obstructed
by each prong, as well as the time that an impact force is first
detected. Velocity measurement shall be accurate to within 5
mm/s [0.20 in./s].
7.4 Conditioning ChamberWhen conditioning materials
at non-laboratory environments, a temperature-/vapor-level
controlled environmental conditioning chamber is required that
shall be capable of maintaining the required temperature to
within 63C [65F] and the required relative humidity level
to within 63 %. Chamber conditions shall be monitored either
on an automated continuous basis or on a manual basis at
regular intervals.
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---

10
Licensee=Universita Bologna - related to 5972936/5935522001
D7136/D7136M 12
8. Sampling and Test Specimens

8.1 SamplingTest at least five specimens per test condition unless valid results can be gained through the use of fewer
specimens, as in the case of a designed experiment. For
statistically significant data the procedures outlined in Practice
E122 should be consulted. The method of sampling shall be
reported.
8.2 Geometry:
8.2.1 Stacking SequenceFor comparison screening of the
drop-weight impact damage resistance of different materials,
the standard specimen thickness shall be 4.0 to 6.0 mm [0.16 to
0.24 in.] with a target thickness of 5.0 mm [0.20 in.] and the
laminate defined as follows:
8.2.1.1 Unidirectional TapeLaminate construction shall
consist of the appropriate number of unidirectional plies to
achieve a total cured thickness nearest to 5.0 mm [0.20 in.]
with a stacking sequence of [45/0/-45/90]NS where N is a
whole number. If the nearest thickness is less than 4.0 mm
[0.16 in.], the next value of N shall be used (N+1). Recommended layups for various nominal cured ply thicknesses are
provided in Table 1. The laminated plate layup is to be defined
such that the 0 fiber orientation is aligned with the lengthwise
(long) dimension.
8.2.1.2 Woven FabricLaminate construction shall consist
of the appropriate number of fabric plies to achieve a total
cured thickness nearest to 5.0 mm [0.20 in.] with a stacking
sequence of [(+45/-45)/(0/90)]NS where N is a whole number.
If the nearest thickness is less than 4.0 mm [0.16 in.], the
next value of N shall be used (N+1). The designations
(+45/-45) and (0/90) represent a single layer of woven fabric
TABLE 1 Recommended Layups for Various Nominal Cured Ply

Thicknesses, Unidirectional Tape
Nominal Cured Ply Thickness
Minimum, mm [in.]
Maximum, mm [in.]
0.085 [0.0033]
0.10 [0.004]
0.13 [0.005]
0.18 [0.007]
0.25 [0.010]
0.50 [0.020]
0.10
0.13
0.18
0.25
0.50
0.75
[0.004]
[0.005]
[0.007]
[0.010]
[0.020]
[0.030]
Ply Count
Layup
48
40
32
24
16
8
[45/0/-45/90]6S
[45/0/-45/90]5S
[45/0/-45/90]4S
[45/0/-45/90]3S
[45/0/-45/90]2S
[45/0/-45/90]S
with the warp and weft fibers oriented at the specified angles.
Fabric laminates containing satin-type weaves shall have
symmetric warp surfaces, unless otherwise specified and noted
in the report. Recommended layups for various nominal cured
ply thicknesses are provided in Table 2. The laminated plate
layup is to be defined such that the 0 fiber orientation is
aligned with the lengthwise (long) dimension.
8.2.1.3 Alternative Stacking SequencesLaminates fabricated using other layups or fiber orientations, or both, may be
evaluated for drop-weight impact damage resistance using this
test method. Tests conducted using alternative stacking sequences must be designated as such, with the stacking sequence recorded and reported with any test results.
8.2.2 Specimen ConfigurationThe geometry of the plate
specimen is shown in Figs. 7 and 8.
NOTE 4It is permissible to impact a panel larger than the specified
dimensions, then to cut out specimens (with the impact site centered) for
subsequent residual strength testing in accordance with Test Method
D7137/D7137M, as long as the panel dimensions and procedures utilized
are recorded as a variation to the test method. Impacting a larger panel can
help relieve interaction between the edge conditions and the damage
creation mechanisms.
8.3 Specimen PreparationGuide D5678 provides recommended specimen preparation practices and should be followed
where practical.
8.3.1 Panel FabricationControl of fiber alignment is
critical. Improper fiber alignment will affect the measured
properties. Erratic fiber alignment will also increase the coefficient of variation. Report the panel fabrication method.
Specimens shall be of uniform cross-section over the entire
surface and shall not have a thickness taper greater than 0.08
mm [0.003 in.] in any direction across the length and width of
the specimen. The coefficient of variation for thickness measurements taken in 11.2.5 should be less than 2 %.
TABLE 2 Recommended Layups for Various Nominal Cured Ply
Thicknesses, Woven Fabric
Nominal Cured Ply Thickness
Minimum, mm [in.]
Maximum, mm [in.]
0.085 [0.0033]
0.10 [0.004]
0.13 [0.005]
0.15 [0.006]
0.18 [0.007]
0.20 [0.008]
0.25 [0.010]
0.36 [0.014]
0.50 [0.020]
1.00 [0.040]
0.10
0.13
0.15
0.18
0.20
0.25
0.36
0.50
1.00
1.50
[0.004]
[0.005]
[0.006]
[0.007]
[0.008]
[0.010]
[0.014]
[0.020]
[0.040]
[0.060]

Ply Count
Layup
48
40
32
28
24
20
16
12
8
4
[(45/-45)/(0/90)]12S
[(45/-45)/(0/90)]10S
[(45/-45)/(0/90)]8S
[(45/-45)/(0/90)]7S
[(45/-45)/(0/90)]6S
[(45/-45)/(0/90)]5S
[(45/-45)/(0/90)]4S
[(45/-45)/(0/90)]3S
[(45/-45)/(0/90)]2S
[(45/-45)/(0/90)]S
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
7.5 Environmental Test ChamberAn environmental test

chamber is required for test environments other than ambient
testing laboratory conditions. This chamber shall be capable of
maintaining the test specimen at the required test environment
during the mechanical test. The test temperature shall be
maintained within 63C [65F] of the required temperature,
and the relative humidity level shall be maintained to within
63 % of the required humidity level.
7.6 Data Acquisition EquipmentFor simple drop-weight
impact testing, no data acquisition equipment is required.
Equipment capable of recording force and velocity data is
required if those measurements are desired. If utilized, such
equipment shall be in accordance with Annex A1, Minimum
Instrumentation Requirements, of Test Method D3763. The
natural frequency of the transducer-impactor assembly shall be
greater than 6 kHz, the analog-to-digital converter shall be
8-bit or greater, the minimum sampling rate shall be 100 kHz,
and the data storage capacity shall be 1000 points or larger.
7.7 Dent Depth IndicatorThe dent depth can be measured
using a dial depth gage, a depth gage micrometer, a tripodmounted depth gage, or a properly calibrated displacement
transducer. The measuring probe shall have a spherical tip with
a maximum radius of curvature of 8.0 mm (0.35 in.). An
instrument with an accuracy of 625 mm [60.001 in.] is
desirable for depth measurement.
7.8 Balance or Weighing ScaleAn analytical balance or
weighing scale is required that is capable of measuring the
impactor mass accurately to 60.5 %.
D7136/D7136M 12
8.3.2 Machining MethodsSpecimen preparation is extremely important for this specimen. Take precautions when
cutting specimens from large panels to avoid notches, undercuts, rough or uneven surfaces, or delaminations due to
inappropriate machining methods. Obtain final dimensions by
water-lubricated precision sawing, milling, or grinding. The
use of diamond-tipped tooling (as well as water-jet cutting) has
been found to be extremely effective for many material
systems. Edges should be flat and parallel within the specified
tolerances. Machining tolerances and surface finish requirements are as noted in Figs. 7 and 8. Record and report the
specimen cutting methods.
8.3.3 LabelingLabel the plate specimens so that they will
be distinct from each other and traceable back to the raw
material, and will neither influence the test nor be affected by
it.
9. Calibration
9.1 The accuracy of all measuring equipment shall have
certified calibrations that are current at the time of use of the
equipment.
10. Conditioning
10.1 The recommended pre-test condition is effective moisture equilibrium at a specific relative humidity as established
by Test Method D5229/D5229M, however, if the test requestor
does not explicitly specify a pre-test conditioning environment,
no conditioning is required and the test specimens may be
tested as prepared.
10.2 The pre-test specimen conditioning process, to include
specified environmental exposure levels and resulting moisture
content, shall be reported with the test data.
NOTE 5The term moisture, as used in Test Method D5229/
D5229M, includes not only the vapor of a liquid and its condensate, but
the liquid itself in large quantities, as for immersion.
10.3 If no explicit conditioning process is performed the

specimen conditioning process shall be reported as unconditioned and the moisture content as unknown.
11. Procedure
11.1 Parameters to be Specified Prior to Test:
11.1.1 The specimen sampling method, specimen type and
geometry, and conditioning travelers (if required).
11.1.2 The damage resistance properties and data reporting
format desired.
NOTE 6Determine specific material property, accuracy, and data
reporting requirements prior to test for proper selection of instrumentation
and data recording equipment. Estimate the specimen damage resistance
to aid in transducer selection, calibration of equipment, and determination
of equipment settings.
11.1.3 The environmental conditioning test parameters.

11.1.4 Diameter of striker tip and mass of impactor.
11.1.5 Nominal impact energy and drop height.
11.1.6 If impact velocity is to be determined, predicted
impact velocity and detector settings (for example, height of
detector above test specimen, distance between leading edges
of flag prongs).
11.1.7 If performed, sampling method, plate specimen geometry, and test parameters used to determine density and
reinforcement volume.
11.2 General Instructions:
11.2.1 Report any deviations from this test method, whether
intentional or inadvertent.
11.2.2 If specific gravity, density, reinforcement volume, or
void volume are to be reported, then obtain these samples from
the same panels being tested. Specific gravity and density may
be evaluated by means of Test Method D792. Volume percent
of the constituents may be evaluated by one of the procedures
of Test Methods D3771.
11.2.3 Following final specimen machining, but before
conditioning, perform a baseline non-destructive inspection of
the specimen to detect flaws or defects which may exist prior
to impact testing. A variety of NDI techniques are available for
detecting both surface and interior flaws in composites. Visual
inspection and liquid penetrant methods can be used for
identifying surface defects, while more sophisticated techniques are required for detecting internal flaws such as cracks,
splits and delaminations. These techniques include ultrasonics,
radiography, thermography, acoustic emission, modal analysis
(such as instrumented tap testing) and eddy-current testing.
Guidance on available techniques and selection of appropriate
methods for specific composite applications is provided in
Guide E2533, as well as section 7.4.2 of MIL-HDBK-17-3F.
Basic principles and procedures for these methods are covered
in the MIL-HDBK-728/1 series, while more specific information on the theory and interpretation of data can be found in
MIL-HDBK-731A for thermography, MIL-HDBK-732A for
acoustic emission, MIL-HDBK-733A for radiography, and
MIL-HDBK-787A for ultrasonics. Record the method(s),
specification(s) and parameters used in the NDI evaluation(s).
NOTE 7The NDI techniques discussed in Guide E2533 and MILHDBK-173F each have particular attributes in regard to sensitivity to
different damage types, ability to detect different types of damage in three
dimensions, and so forth. It may be necessary to utilize a combination of
NDI techniques to properly characterize the three-dimensional damage
state in some instances (for example, when multiple-layer delaminations
and matrix cracks are present).
11.2.4 Condition the specimens as required. Store the specimens in the conditioned environment until test time, if the test
environment is different than the conditioning environment.
11.2.5 Following final specimen machining and any conditioning, but before all testing, measure the specimen width, w,
and length, l, at two locations in the vicinity of the location to
be damaged. The thickness of the specimen shall be measured
at four locations near the impact location, and recorded as the
average of the four measurements. The accuracy of all measurements shall be within 1 % of the dimension. Record the
dimensions to three significant figures in units of millimetres
[inches].
11.3 Test EnvironmentIf possible, test the specimen under
the same fluid exposure level used for conditioning. However,
cases such as elevated temperature testing of a moist specimen
place unrealistic requirements on the capabilities of common
environmental chambers. In such cases the mechanical test
environment may need to be modified, for example, by testing
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---

12
D7136/D7136M 12
at elevated temperature with no fluid exposure control, but with
a specified limit on time to test after withdrawal from the
conditioning chamber. Record any modifications to the test
environment.
NOTE 8When testing a conditioned specimen at elevated temperature
with no fluid exposure control, the percentage moisture loss of the
specimen prior to test completion may be estimated by placing a
conditioned traveler coupon of known weight within the test chamber at
the same time the specimen is placed in the chamber. Upon completion of
the test, the traveler coupon is removed from the chamber, weighed, and
the percentage weight calculated and reported.
11.4 Impactor PreparationPrepare the impactor by attaching the hemispherical striker tip and adding required mass.
If the mass of the impactor (or any component(s) of the
impactor) is unknown or uncertain, weigh the impactor (or
component(s)) to a precision of 60.5 % using the balance or
weighing scale. Mount the impactor in the impact device, and
prepare force measurement instrumentation as required. All of
the components must be rigidly attached to each other, to
minimize resonance during the impact event.
11.5 Specimen InstallationPlace the specimen in the support fixture, ensuring the specimen is centered relative to the
cut-out. Unless otherwise specified, impact the tool side of the
specimen. Secure the specimen in place using the four rubbertipped clamps (applying minimal clamping force such that the
clamp tips barely touch the specimen) to prevent the specimen
from rebounding during the impact event. The clamp tips
should be positioned approximately 25 mm [1.0 in.] from the
specimen edges.
11.6 Velocity IndicatorIf utilized, position the velocity
detector at a point such that the velocity measurement is
completed between 3 to 6 mm [0.13 to 0.25 in.] vertically
above the surface of the specimen.
11.7 Drop Height:
11.7.1 Impact Energy CalculationsCalculate the impact
energy level using Eq 1 unless otherwise specified. Record the
impact energy level to three significant figures.
E 5 CE h
(1)
where:
E = potential energy of impactor prior to drop, J [in.-lbf],
CE = specified ratio of impact energy to specimen thickness, 6.7 J/mm [1500 in.-lbf/in], and
h = nominal thickness of specimen, mm [in.].
11.7.2 Drop Height CalculationCalculate the drop height
required to produce the specified impact energy, and record the
drop height to three significant figures. Utilize Eq 2 when using
SI units and Eq 3 when using inch-pound units.
E
H5m g
(2)
where:
H = drop-height of impactor, m,
md = mass of impactor for drop height calculation, kg, and
g = acceleration due to gravity, 9.81 m/s2.
H5m
where:
E
dlbm
(3)
H
mdlbm
= drop-height of impactor, in., and

= mass of impactor in standard gravity for drop
height calculation, lbm.
NOTE 9The selected impactor mass must permit a minimum drop

height of 300 mm [12 in.].
NOTE 10The pound mass is defined such that one pound force
imparts an acceleration of 32.17 ft/s2 to it. In standard gravity, one pound
force is numerically the same as one pound mass, so it is not necessary to
include the term for gravitational acceleration in the inch-pound version of
the equation.
11.7.3 Raise ImpactorPosition the impactor at the calculated drop height.

11.8 ImpactDrop the impactor to impact the specimen
once without a rebound impact.
NOTE 11Some impact devices may utilize mechanisms to automatically prevent rebound hits. If such equipment is unavailable, this may be
done by sliding a piece of rigid material (wood, metal, and so forth)
between the impactor and specimen, after the impactor rebounds from the
specimen surface after impact.
11.9 Data RecordingIf instrumentation is utilized, record

force versus time data during contact continuously or at
frequent regular intervals; for this test method, a sampling rate
of 100 kHz and a target minimum of 100 data points per test
are recommended. Record the time at which the velocity
indicator light beam is interrupted by each of the flag prongs.
11.9.1 Examples of recorded contact force versus time
curves are shown in Figs. 9 and 10. The onset of specimenimpactor contact is noted by the detection of a non-zero contact
force. As the impactor presses into the specimen, it will flex the
specimen and form a local depression as the contact force
increases. Sharp drops in recorded contact force indicate
damage processes that result in a sudden loss of stiffness in the
contact region.
NOTE 12Rapid increases and decreases in recorded contact force
response with time, shown in Fig. 10, can result from harmonic resonance
of the impactor, load cell or specimen during the impact event. Significant
resonance can make determination of the F1 force and E1 energy difficult.
For material forms such as plastics, post-test digital smoothing is often
utilized to understand the effective peak force and absorbed energy in such
instances. For composite materials, however, the oscillations in the force
response most often reflect actual forces applied to the specimen and
should not be smoothed out. The use of digital post-processing can also
smooth out sharp drops in the impact response curve. If smoothing is
used in data interpretation, both the recorded data and the post-processed
smoothed data shall be reported, along with a description of the
post-processing algorithm. Additional information on interpreting data
from impact force data may be found in Appendix X1 of Test Method
D3763.
11.9.2 Parameters which can be determined from the contact force versus time curve(s) after the test include the F1 force
(recorded contact force at which the force versus time curve
has a discontinuity in force or slope), the maximum contact
force Fmax, absorbed energy E1 (at F1 force), absorbed energy
Emax (at maximum contact force), and contact duration tT.
11.10 Dent DepthMeasure the dent depth, as defined in
3.2.2, using a suitable dent depth indicator as defined in 7.7.
The dent shall be measured immediately after the specimen is
impacted. If distances are measured relative to a fixed point,
the dent depth will be the difference between the lowest point
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---

13
D7136/D7136M 12
NOTE 13Dimensional tolerances for the measured damage width,

length and diameter are dependent upon the NDI method(s) utilized.
11.12.3 Record the damage mode(s) observed for each

specimen, and the surface(s) and location(s) at which the
damage modes are observed. More than one damage mode may
be present in a damaged specimen. Fig. 12 illustrates commonly observed damage modes.
12. Validation
12.1 Property values shall not be calculated for any specimen that forms damage or breaks at some obvious flaw, unless
such flaw constitutes a variable being studied. Retests shall be
performed for any specimen on which values are not calculated.
12.2 If a significant number of specimens in a sample
population exhibit damage originating or extending significantly away from the impact location, the impact support
conditions shall be re-examined. Factors considered should
include fixture alignment, impactor guide tube alignment, gaps

between the specimen and restraints, and specimen thickness
taper.
13. Calculation
13.1 Impact VelocityIf the impact device is capable of
detecting the velocity of the impactor, calculate the impact
velocity using Eq 4 and report the results to three significant
figures. This calculation is performed automatically by most
systems with velocity detection capability, but may be performed manually using the indicated timing data if necessary.
vi 5
~W12!
~t1 1 t2!
1 g ti 2
2
~t2 2 t1!
(4)
where:
= impact velocity, m/s [in./s],
vi
W12 = distance between leading edges of the first (lower)
and second (upper) flag prongs, m [in.],
= time first (lower) flag prong passes detector,
t1
= time second (upper) flag prong passes detector, and
t2
= time of initial contact obtained from force versus
ti
time curve, s.
13.2 Measured Impact EnergyIf the impact device is
capable of detecting the velocity of the impactor, calculate the
actual impact energy using Eq 5 and report the results to three
significant figures. This calculation is performed automatically
by most systems with velocity detection capability, but may be
performed manually if necessary. The measured impact energy
may differ from the nominal impact energy calculated in 11.7.1
due to friction losses during the drop.
m vi2
Ei 5 2
(5)
where:
Ei = measured impact energy, J [in.-lbf], and
m = mass of impactor, kg [lbm].
13.3 StatisticsCalculate the average value, standard deviation, and coefficient of variation (in percent) for d for each
series of tests If the impact device is capable of detecting the
contact force and velocity of the impactor, also perform such
calculations for impact velocity, impact energy, F1, Fmax, E1,
Emax and tT for each series of tests:
n
x 5 ~ ( xi!/n
i51
(
n
Sn21 5
i51
xi2 2 n x2!/~n 2 1!
CV 5 100 3 Sn21/x
(6)
(7)
(8)
where:
x
= sample mean (average),
Sn-1 = sample standard deviation,
CV = sample coefficient of variation, %,
n
= number of specimens, and
= measured or derived property.
xi
13.4 Velocity versus TimeIf the impact device is monitoring contact force, generate a curve of nominal velocity versus
time using Eq 9 and numerical integration of the force versus
time data. A positive velocity value represents downward
14
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
in the dent and the plate surface. The distance to the plane of
the specimens surface shall be the average of four measurements spaced 90 apart and at least 25 mm [1.0 in.] from the
impact point to provide a sufficient distance away from the dent
to not influence the measurement. If the depth is measured
directly using a depth gage, the depth shall be the average of
two measurements with the gage rotated 90 between measurements. The base of the depth gage shall be at least 50 mm [2.0
in.] and sufficiently large to span over the region affected by the
dent. These requirements also apply if the depth is measured
using a tripod-mounted depth gage (one which bases its
reference surface on a micrometer holder that touches the
surface at three points on a prescribed diameter). The dent
depth shall be measured to the nearest 0.03 mm [0.001 in.].
11.11 Dent RelaxationOver time, or under environmental
exposure, the dent depth may decrease due to relaxation of the
composite material. If information on short term dent relaxation is desired, measure the dent depth 7 days after impacting
as in 11.10. Record the dent depth, the time duration after
impacting that the measurement was taken, and the environmental conditions prior to measurement.
11.12 Non-Destructive Inspection:
11.12.1 Evaluate the extent of damage caused by the impact
event using non-destructive inspection (NDI) techniques. Utilize NDI method(s), specification(s), and parameters consistent
with those used to evaluate the specimen prior to impact in
11.2.3. Record the method(s), specification(s), and parameters
used in the NDI evaluation(s).
11.12.2 Measure and record geometric dimensions for the
detected damage, using a suitable instrument as defined in 7.1.
Using Fig. 11 as a guide, determine locations of the eight
indicated points relative to the center of the specimen. Also
determine the damage width, damage length, and maximum
damage diameter. Alternative measurement locations may be
required to characterize the extent of damage for non-standard
layups or fiber orientations, or both. Alternatively, automated
algorithms may be used to define the extent of damage and to
calculate the two-dimensional damage area using digital NDI
data.
motion. Common numerical integration algorithms used in this

application include the trapezoidal rule and Simpsons rule (2
and 3 point Newton-Cotes formulas, respectively.6 The time
step of the numerical integration must be equal to the time step
(inverse of the frequency) of data sampling.
v~t! 5 vi 1 g t 2
F~t!
m dt
(9)
where:
v = impactor velocity at time t, m/s [in./s],
t = time during test, in which t = 0 is the time when the
impactor initially contacts the specimen, s, and
F = measured impactor contact force at time t, N [lbf].
13.5 Impactor Displacement versus TimeIf the impact
device is monitoring contact force, generate a curve of impactor displacement versus time using Eq 10 and numerical
integration of the force versus time data. A positive displacement value represents downward displacement from the drop
height.
g t2
d~t! 5 di 1 vi t 1 2 2
* S*
t
F~t!
m dt dt
(10)
where:
d = impactor displacement at time t, m [in.], and
di = impactor displacement from reference location at time
t = 0, m [in.].
13.6 Absorbed Energy versus TimeIf the impact device is
monitoring contact force, generate a curve of energy absorbed
by the specimen versus time using Eq 11.
Ea~t! 5
m~vi2 2 v~t!2!
1 m g d~t!
2
(11)
where:
Ea = absorbed energy at time t, J [in.-lbf].
14. Report
14.1 Report the following information, or references pointing to other documentation containing this information, to the
maximum extent applicable (reporting of items beyond the
control of a given testing laboratory, such as might occur with
material details or panel fabrication parameters, shall be the
responsibility of the requestor):
NOTE 14Guides E1309 and E1434 contain data reporting recommendations for composite materials and composite materials mechanical
testing.
14.1.1 The revision level or date of issue of this test method.

14.1.2 The name(s) of the test operator(s).
14.1.3 Any variations to this test method, anomalies noticed
during testing, or equipment problems occurring during testing.
14.1.4 Identification of all the applicable constituent information, including: material specification, material type, manufacturers material designation, manufacturers batch or lot
number, source (if not from manufacturer), date of certification, expiration of certification, filament diameter, tow or yarn
filament count and twist, sizing, form or weave, fiber areal
weight, matrix type, matrix content, and volatiles content.
6
Whittaker, E. T., and Robinson, G., The Calculus of Observations: A Treatise
on Numerical Mathematics, 4th ed., New York: Dover, 1967, pp. 156-158.

14.1.5 Description of the fabrication steps used to prepare

the parent laminate including: fabrication start date, fabrication
end date, process specification, cure cycle, consolidation
method, and a description of the equipment used.
14.1.6 Ply orientation and stacking sequence of the laminate, relative to the longitudinal (long) dimension.
14.1.7 If requested, report density, volume percent reinforcement, and void content test methods, specimen sampling
method and geometries, test parameters, and test results.
14.1.8 Method of preparing the test specimen, including
specimen labeling scheme and method, specimen geometry,
sampling method, and specimen cutting method.
14.1.9 Calibration dates and methods for all measurements
and test equipment.
14.1.10 Type and configuration of test machine, data acquisition equipment, data sampling rate.
14.1.11 If applicable, type of velocity detector and key
parameters (for example, height of detector above test specimen, distance between leading edges of flag prongs), type of
force detector.
14.1.12 Measured length, width and thickness for each
specimen (prior to and after damage and conditioning, if
appropriate).
14.1.13 Weight of specimen, type of balance or weighing
scale, and measurement accuracy.
14.1.14 Conditioning parameters and results.
14.1.15 Relative humidity and temperature of the testing
laboratory.
14.1.16 Environment of the test machine environmental
chamber (if used) and soak time at environment.
14.1.17 Number of specimens tested.
14.1.18 Diameter of hemispherical impactor striker tip.
14.1.19 Total mass of impactor.
14.1.20 Nominal impact energy and drop height.
14.1.21 Results of nondestructive evaluation tests, including
method, specification, inspection parameters and operator, both
before and after impact.
14.1.22 Damage geometry, including positions of the eight
specified measurement points, damage width, damage length,
maximum damage diameter, damage area (if calculated), and
through-thickness location.
14.1.23 Damage modes and locations observed for each
specimen.
14.1.24 Individual dent depths, along with average value,
standard deviation, and coefficient of variation (in percent) for
the population.
14.1.25 If dent relaxation is evaluated, individual dent
depths after relaxation, along with the time duration after
impacting and the environmental conditions prior to measurement.
14.1.26 Individual values of F1, Fmax, E1 and Emax, if these
parameters were measured, along with average value, standard
deviation, and coefficient of variation (in percent) for the
population.
14.1.27 Contact force versus time history data for each
specimen so evaluated.
15
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
D7136/D7136M 12
D7136/D7136M 12
14.1.28 Impact velocity and actual impact energy for each
specimen so evaluated, along with average value, standard
deviation, and coefficient of variation (in percent) for the
population.
14.1.29 Contact duration for each specimen so evaluated,
along with average value, standard deviation, and coefficient of
variation (in percent) for the population.
14.1.30 Velocity, impactor displacement and absorbed energy versus time histories for each specimen so evaluated,
along with method of numerical integration utilized.
Committee D30 is currently planning a round-robin test series

for this test method in order to determine precision.
15.2 BiasBias cannot be determined for this test method
as no acceptable reference standard exists.
16. Keywords
16.1 composite materials; damage resistance; drop-weight
impact; impact testing
15. Precision and Bias

15.1 PrecisionThe data required for the development of a
precision statement is not available for this test method.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).

16
--`,``,`````,,``,```````,,`,,``,-`-`,,`,,`,`,,`---
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM D7136 Low Velocity Impact

Uploaded by

Copyright:

Available Formats

ASTM D7136 Low Velocity Impact

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ASTM D7136 Low Velocity Impact

Uploaded by

Copyright:

Available Formats

What is the purpose of this test method?

What is the purpose of this test method?

What parameters are measured in this test method?

What parameters are measured in this test method?

Designation: D7136/D7136M 12

Standard Test Method for

Measuring the Damage Resistance of a Fiber-Reinforced

each system may not be exact equivalents; therefore, each

Copyright ASTM International

1Licensee=Universita Bologna - related to 5972936/5935522001

Copyright ASTM International

NOTEClamp tip centered 0.25 in. from edge of cut-out.

NOTEClamp tip centered 6 mm from edge of cut-out.

x = mean or average (estimate of mean) of a sample population for a given property

FIG. 3 Representative Rigid Base (Inch-Pound Version)

FIG. 4 Representative Rigid Base (SI Version)

Copyright ASTM International

5.2 Drop-weight impact testing can serve the following

4Licensee=Universita Bologna - related to 5972936/5935522001

FIG. 5 Impact Device with Cylindrical Tube Impactor Guide Mechanism

FIG. 6 Impact Device with Double Column Impactor Guide Mechanism

include dent depth, damage dimensions, and through-thickness

Copyright ASTM International

5.2.3 To impart damage in a specimen for subsequent

5Licensee=Universita Bologna - related to 5972936/5935522001

FIG. 7 Drop-Weight Impact Test Specimen (Inch-Pound Version)

FIG. 8 Drop-Weight Impact Test Specimen (SI Version)

5.3 The properties obtained using this test method can

ness, stacking sequence, and so forth. However, it must be

FIG. 9 Representative Impactor Force versus Time History

FIG. 10 Impactor Force versus Time History with Harmonic Resonance

thickness, stiffness, mass, support conditions, and so forth.

damage resistance characteristics of an unstiffened monolithic

Copyright ASTM International

7Licensee=Universita Bologna - related to 5972936/5935522001

FIG. 11 Measurement of Extent of Damage

those of a panel significantly larger than the test specimen,

impact and compressive residual strength tests can then be

Copyright ASTM International

8Licensee=Universita Bologna - related to 5972936/5935522001

the impact location, can affect the impact deformation and

actual forces applied to the specimen and should not be filtered

FIG. 12 Commonly Observed Damage Modes from Out-of-Plane Drop-Weight Impact

7.2 Support FixtureThe impact support fixture, shown in

7.3 Impact DeviceRepresentative drop-weight impact

7.3.1 ImpactorThe impactor shall have a mass of 5.5 6

Copyright ASTM International

8. Sampling and Test Specimens

TABLE 1 Recommended Layups for Various Nominal Cured Ply

11Licensee=Universita Bologna - related to 5972936/5935522001

7.5 Environmental Test ChamberAn environmental test

10.3 If no explicit conditioning process is performed the

11.1.3 The environmental conditioning test parameters.

Copyright ASTM International

= drop-height of impactor, in., and

NOTE 9The selected impactor mass must permit a minimum drop

11.7.3 Raise ImpactorPosition the impactor at the calculated drop height.

11.9 Data RecordingIf instrumentation is utilized, record

Copyright ASTM International

NOTE 13Dimensional tolerances for the measured damage width,