Simulation of Power Electronics Circuits Using SIMULINK

!

"#"$%

"#"$%

"#"$% " &'() *(

+

,

-

.

/

01-2341
5 - / ( (

6 #- 7008
( (
#(-
7004 /

9

% #-) -% /

(
)

!!""#

!"

!

" # $ !%
! & $ '
' ($ ' # % %
) %* %' $ '
+ " % &
' ! #
$,
( $

- .

!
"- ( %

.
% % % %
$ $ $ -
-
- -
// $$$
0
1"1"#23."

4&)*5/ +)

* !6!& 7!8%779:9& % ) 2
; !
* &

/- <:=9>4&)*5/ +)
"3 " & :=9>
Simulation of Power Electronics Circuits

using SIMULINK
by
Hadeed Ahmed Sher

Department of Electrical Engineering,
King Saud University,
Riyadh, Kingdom of Saudi Arabia
Dedicated to my Wife and my family
Preface
Power electronics is a core eld in automation and industrial world. It forms the life
lines of industrial revolution in the present era. A lot of books on power electronics
are available in market. These books, in general, cover the theoretical aspects of power
electronics. Presently software based simulation has gained a lot of attention and is
considered most eective tool for research and development in engineering. MATLAB
is one of the most powerful tools for analyzing the hypothesis and ideas of engineers.
Within MATLAB is SIMULINK, that provides us a modular approach to solve problems.
The prime aim of this book is to facilitate students in an elegant manner about using
SIMULINK in general and SIM POWER SYSTEMS in particular. A very basic approach
is adopted as each and every step is depicted to facilitate the students in getting grip of
this powerful tool. The book has six chapters. First chapter explains the importance of
modeling and simulation and i have tried my best to explain the very basics of modeling
a physical system and above all why simulation is required. This section also highlights
the choice of using SIMULINK mainly when a variety of powerful softwares are available.
Chapter two and three covers the rectiers with a dierence that chapter three is about
the SCR based controlled rectiers. Inverters are discussed in chapter 4. Variety of
dierent inverters including single phase, quasi wave and three phase with induction
motor as load are presented in it. AC-AC conversion is covered in chapter 5 with a
title of cycloconverters. Here only single phase to single phase and three phase to single
phase step down cycloconverter are simulated. Chapter 6 covers basic types of DC-DC
converters and along with them full bridge converters are simulated using unipolar and
bipolar PWM switching.
The focus of this book is simulating power electronics circuits using SIMULINK, therefore detailed theory is not presented. Readers are advised to consult the standard text
books for theoretical explanation of these circuits. The simulation results in this book are
veried using the famous power electronic books by renowned authors. The experiments
in this book are written keeping in view the undergraduate course of power / industrial
electronics in almost all universities and technological institutes of region, however it
can be considered as a useful quick reference guide for the students of graduate classes.
I am greatly thankful to my family, colleagues and friends for providing support in accomplishing this task. Any comments and suggestions regarding this book are greatly
welcomed and should be sent to the hadeedsher[at]gmail[dot]com.
Hadeed Ahmed Sher
KSU, Riyadh, Saudi Arabia
Page II
Contents
1 Introduction to Modeling and Simulation
1.1 Importance of Simulation . . . . . . .
1.2 Why Simulink . . . . . . . . . . . . . .
1.3 SIMPOWER SYSTEM . . . . . . . .
1.4 Architecture of book . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
3
4
5
2 Uncontrolled Rectiers
2.1 Introduction . . . . . . . . . . . . . . . . .
2.2 Single phase half wave rectier . . . . . .
2.2.1 Without freewheeling diode . . . .
2.2.2 With freewheeling diode . . . . . .
2.3 Single phase full wave center tap rectier
2.3.2 With freewheeling diode . . . . . .
2.4 Single phase full wave bridge rectier . . .
2.4.1 Without free wheeling diode . . . .
2.4.2 With free wheeling diode . . . . .
2.5 Three phase full wave rectier . . . . . . .
2.6 Twelve pulse rectier . . . . . . . . . . . .
2.6.1 Simulation Procedure . . . . . . .
2.6.2 Results . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
6
6
6
6
19
20
20
23
23
24
25
27
27
29
29
32
3 Controlled Rectiers/Converters
3.1 Introduction . . . . . . . . . . . . . . . . . . . .
3.2 Single phase half wave controlled converter . .
3.2.1 Simulation Procedure . . . . . . . . . .
3.2.2 Results . . . . . . . . . . . . . . . . . .
3.3 Single phase full wave half controlled converter
3.3.2 Results . . . . . . . . . . . . . . . . . .
3.4 Single phase full wave full controlled converter
3.4.2 Results . . . . . . . . . . . . . . . . . .
3.5 Three phase full controlled bridge converter . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
34
34
35
35
36
38
39
39
40
40
41
43
.
.
.
.
Page III
Contents
3.5.2
Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4 DC-AC Inverters
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Pulse Width Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1 Simulation Procedure . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Single phase half bridge inverter . . . . . . . . . . . . . . . . . . . . . . .
4.3.1 Simulation procedure . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 Single phase PWM inverter with bipolar voltage switching . . . . . . . . .
4.4.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5 Single phase PWM inverter with Unipolar voltage switching . . . . . . . .
4.5.1 Simulation procedure . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.6 Quasi square wave single phase Inverter . . . . . . . . . . . . . . . . . . .
4.6.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.7 Single phase inverter with hysteresis band current controlled PWM . . . .
4.7.1 Simulation Procedure for PWM . . . . . . . . . . . . . . . . . . . .
4.7.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8 PWM based DC-AC 3 phase Inverter . . . . . . . . . . . . . . . . . . . . .
4.8.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.9 SPWM based 3 phase inverter with 3 phase Asynchronous motor as load .
4.9.2 Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
46
47
50
52
52
54
54
54
55
58
58
58
60
60
61
63
64
65
67
67
68
72
72
73
76
5 Cycloconverters
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Single phase to Single phase Step down Cycloconverter
5.2.1 Simulation Procedure . . . . . . . . . . . . . .
5.2.2 Results . . . . . . . . . . . . . . . . . . . . . .
5.3 Three phase to Single phase Step down Cycloconverter
5.3.1 Simulation Procedure . . . . . . . . . . . . . .
5.3.2 Results . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
80
80
83
83
85
87
87
88
6 DC-DC Converters
6.1 Introduction . . . . . . . . . .
6.2 DC-DC Buck Converter . . .
6.2.1 Simulation Procedure
6.2.2 Results . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
91
91
91
92
92
Page IV
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Contents
6.3
6.4
6.5
6.6
DC-DC Boost Converter . . . . . . . . . .

6.3.2 Results . . . . . . . . . . . . . . .
DC-DC Buck / Boost Converter . . . . .
6.4.2 Results . . . . . . . . . . . . . . .
` K DC-DC Converter . . . . . . . . . .
CU
6.5.1 Simulation procedure . . . . . . .
6.5.2 Results . . . . . . . . . . . . . . .
Full Bridge DC DC Converter . . . . . . .
6.6.1 Full Bridge DC DC Converter with
6.6.2 Full Bridge DC DC Converter with
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
Bipolar Voltage Switching .
Unipolar Voltage Switching
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
93
94
95
95
95
97
99
100
101
101
102
105
Page V
List of Figures
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
2.22
2.23
2.24
2.25
2.26
2.27
2.28
2.29
2.30
2.31
2.32
2.33
2.34
2.35
Page VI
1 half wave rectier with RL load . . . . . . . . . . . . . . . . . . . .

Reaching simulink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating a new model . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding a block in the model . . . . . . . . . . . . . . . . . . . . . . . . .
Construction of a model . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the oscilloscope . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the oscilloscope parameters . . . . . . . . . . . . . . . . . . .
Getting towards the simulation parameters . . . . . . . . . . . . . . . .
Adjusting the simulation parameters . . . . . . . . . . . . . . . . . . . .
Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FFT analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Half wave rectier with free wheeling diode . . . . . . . . . . . . . . . .
Output waveforms with free wheeling diode . . . . . . . . . . . . . . . .
FFT of the rectier with free wheeling diode . . . . . . . . . . . . . . .
Circuit arrangement for single phase full wave center tap rectier . . . .
Adjusting the transformer parameters . . . . . . . . . . . . . . . . . . .
Output waveform of center tapped full wave rectier . . . . . . . . . . .
Center tapped full wave rectier with free wheeling diode . . . . . . . .
Output waveform of center tapped full wave rectier with free wheeling
diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full wave bridge rectier . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full wave bridge rectier without freewheeling diode . . . . . . . . . . .
Output of full wave bridge rectier without freewheeling diode . . . . .
Full wave bridge rectier with freewheeling diode . . . . . . . . . . . . .
Full wave bridge rectier with freewheeling diode . . . . . . . . . . . . .
Three phase full wave bridge rectier . . . . . . . . . . . . . . . . . . . .
Simulation setup for three phase full wave rectier . . . . . . . . . . . .
Three phase balanced input . . . . . . . . . . . . . . . . . . . . . . . . .
Three phase balanced input . . . . . . . . . . . . . . . . . . . . . . . . .
Output of three phase full wave bridge rectier . . . . . . . . . . . . . .
Simulation setup for twelve pulse rectier . . . . . . . . . . . . . . . . .
Three phase three winding transformer block parameters . . . . . . . . .
Waveforms for twelve pulse rectier . . . . . . . . . . . . . . . . . . . . .
FFT of primary current of transformer for phase A . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
8
9
9
10
11
13
13
14
16
16
18
18
19
19
20
21
22
22
23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
23
24
24
25
25
26
27
28
29
30
30
31
32
33
33
List of Figures
3.1
3.2
3.3
3.4
3.5
3.6
35
36
36
37
37
3.14
3.15
Single phase half wave controlled rectier . . . . . . . . . . . . . . . . . .

Simulation setup for single phase half wave controlled rectier . . . . . . .
Waveforms for single phase half wave controlled rectier . . . . . . . . . .
Single phase full wave semi-controlled rectier . . . . . . . . . . . . . . . .
Single phase full wave semi-controlled rectier with improved conguration
Simulation setup for two topologies of single phase full bridge half controlled converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Simulation results for two topologies of single phase full bridge half controlled converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single phase full wave Full-controlled converter . . . . . . . . . . . . . . .
Simulation setup for 1 full wave full-controlled converter . . . . . . . . .
Simulation results for 1 full wave full-controlled converter . . . . . . . .
Input parameters waveforms for single phase full bridge full controlled
converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Three phase SCR based full wave full controlled converter . . . . . . . . .
Simulation setup for three phase SCR based full wave full controlled converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage of 3 full wave full-controlled converter . . . . . . . . . .
Input current analysis of 3 full wave full-controlled converter . . . . . .
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
Typical three phase inverter [4] . . . . . . . . . . . . . . . . . . . . .

Pulse Width Modulation . . . . . . . . . . . . . . . . . . . . . . . . .
Three phase sinusoidal PWM [5] . . . . . . . . . . . . . . . . . . . .
Generation of triangular waveform . . . . . . . . . . . . . . . . . . .
Triangular waveform . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWM generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Results of PWM with dierent value of constant. . . . . . . . . . . .
Single phase SinePWM . . . . . . . . . . . . . . . . . . . . . . . . . .
Results of three phase SPWM. . . . . . . . . . . . . . . . . . . . . .
Simulation setup of single phase half bridge inverter . . . . . . . . .
Subsystem for PWM generation of single phase half bridge inverter .
Results of Half bridge Inverter with Resistive load. . . . . . . . . . .
Results of Half bridge Inverter with Inductive load. . . . . . . . . . .
Simulation setup of single phase inverter with bipolar switching . . .
Single phase asynchronous motor . . . . . . . . . . . . . . . . . . . .
Waveforms for Single phase inverter with bipolar switching . . . . .
Simulation setup of single phase inverter with unipolar switching . .
Output waveforms of single phase inverter with unipolar switching .
FFT of output of single phase inverter with unipolar switching . . .
Simulation setup for quasi square wave single phase inverter . . . . .
Subsystem for quasi square wave single phase inverter . . . . . . . .
Results of quasi square wave inverter. . . . . . . . . . . . . . . . . .
Block diagram for simulation of hysteresis band 3 phase inverter [6] .
Conceptual explanation of hysteresis band single phase inverter [6] .
47
48
49
50
51
51
52
53
53
55
55
57
57
58
59
60
61
62
63
64
64
65
65
66
3.7
3.8
3.9
3.10
3.11
3.12
3.13
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
38
39
40
41
41
42
42
44
44
45
Page VII
List of Figures
4.25
4.26
4.27
4.28
4.29
4.30
4.31
4.32
4.33
4.34
4.35
4.36
4.37
4.38
Simulation setup of hysteresis band inverter . . . . . . . . . . . . . . . .

Results of PWM inverter using hysteresis band method. . . . . . . . . .
Modeling of leg of an inverter [1] . . . . . . . . . . . . . . . . . . . . . .
Modeling of output voltages of inverter [1] . . . . . . . . . . . . . . . . .
Complete model of an inverter [1] . . . . . . . . . . . . . . . . . . . . . .
Results three phase Inverter. . . . . . . . . . . . . . . . . . . . . . . . .
FFT of inverter waveform . . . . . . . . . . . . . . . . . . . . . . . . . .
Simulation setup for 3 phase inverter with 3 phase asynchronous motor
as load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter adjustment of universal bridge . . . . . . . . . . . . . . . . .
Asynchronous motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measurement selection of bus selector . . . . . . . . . . . . . . . . . . .
Parameter adjustment of STEP input . . . . . . . . . . . . . . . . . . .
Output of motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal voltages and three phase stator currents . . . . . . . . . . . . .
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
General diagram of a cycloconverter [3] . . . . . . . . . . .

General diagram of a cycloconverter [6] . . . . . . . . . . .
Output waveform of a cycloconverter [3] . . . . . . . . . . .
Simulation setup of a single phase to single phase step down
Selection of measurements . . . . . . . . . . . . . . . . . . .
Plotting of measurements . . . . . . . . . . . . . . . . . . .
Three phase to single phase cycloconverter [3] . . . . . . .
Simulation setup for 3 phase to 1 phase cycloconverter . . .
Timing diagram of pulses . . . . . . . . . . . . . . . . . . .
Output without lter . . . . . . . . . . . . . . . . . . . . . .
Output with lter . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
cycloconverter
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
DC-DC buck converter . . . . . . . . . . . . . . .

DC-DC buck converter simulation setup . . . . .
DC-DC buck converter simulation results . . . .
DC-DC boost converter . . . . . . . . . . . . . .
DC-DC boost converter simulation setup . . . .
DC-DC boost converter output current . . . . .
DC-DC boost converter simulation results . . .
DC-DC buck / boost converter . . . . . . . . . .
DC-DC buck / boost converter simulation setup
Simulation results with 25% duty cycle . . . . .
Simulation results with 50% duty cycle . . . . .
Simulation results with 75% duty cycle . . . . . .
` K DC-DC converter . . . . . . . . . . . . . .
CU
` K DC-DC converter . . .
Simulation setup of CU
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Page VIII
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
67
67
70
71
72
73
74
.
.
.
.
.
.
.
75
76
77
77
78
78
79
.
.
.
.
.
.
.
.
.
.
.
.
.
.
81
82
82
84
85
85
86
86
88
89
89
90
90
92
93
94
94
95
96
96
97
97
98
98
99
99
100
List of Figures
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
` K converter. . . . . . . . . . . . . . . . . . .
Simulation results of CU
Full Bridge DC DC converter [6] . . . . . . . . . . . . . . . . . . . .
Bipolar voltage switching [6] . . . . . . . . . . . . . . . . . . . . . . .
Simulation setup for bridge converter with bipolar voltage switching
Subsystem for bipolar voltage switching . . . . . . . . . . . . . . . .
Simulation results of bridge converter with bipolar voltage switching
Voltage waveforms for unipolar voltage switching [6] . . . . . . . . .
Subsystem for unipolar voltage switching . . . . . . . . . . . . . . .
Simulation results for unipolar voltage switching . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
101
102
103
104
104
105
106
107
108
Page IX

1.1 Importance of Simulation
Circuit performance is a key factor in designing a system in electrical engineering. Each
and every component contributes towards the overall performance of a system. In high
power electronics known as power electronics we need to be very focused towards the
evaluation of system. Not only the components but the junction capacitances and noise
also aect the output waveforms. In this modern world power electronics engineers are
assisted by control engineers that providing them very useful control chips for signal
generation and circuit operation. But these control ICs are also very complex and
therefore it is desired to analyze them using software based tools. Circuit simulation is
fast becoming an alternative to prototyping. Software based simulation is now considered
as an optional aid in learning power electronics. Simulation is an art of converting a
circuit design into a software model and then testing it using input stimuli and output
monitoring. It can be used to evaluate the performance of new circuits for enhancement
of knowledge. The aws in any circuit can be corrected at early design stage with the
help of simulation. Novel techniques can be tested using simulation based packages that
saves cost, time and any potential hazard that can arise from short circuit across power
components. Apart from its wide use in academia, industrial users gains benet from
simulation by verifying their process performance. Simulation in the past received critics
as it adds another step in design cycle but with on going work based on simulation it has
been now proved that, as a product progresses through the design cycle, errors become
more and more costly to correct. It is best for conducting studies for destructive nature
of tests of electric machines. Simulation is an excellent way to reveal logic and/or timing
errors in a circuit before continuing for the prototyping. With simulation we can do a
variety of operations including the following [3, 6]
Waveforms at various points of circuit
Circuit performance in transient and steady state condition that may be very
dicult in hardware prototype.
Assessment of performance improvement / degradations
Measurement of noise and distortion at any node / point of circuit without using
expensive network signal analyzers
Voltage and current ratings by examining the waveforms
Calculation of tolerance level for various components that leads to sensitivity analysis.
Page 1
1.1 Importance of Simulation

Harmonics analysis without using any expensive equipment
Evaluate the eects of non linear elements on circuit performance
Optimize the design of electronic circuits in terms of circuit parameters
Measurement of power losses for various components including the power switches
and diodes.
Development of temperature versus losses curves for circuit elements
Simulation in the eld of power electronics is somewhat dierent then other elds of
electrical engineering due to its interdisciplinary nature. Almost every circuit of power
electronics exhibits an extremely non linear behavior that makes it dicult to accurately
model circuit elements. The simulation time is not constant i.e it may be possible that an
inverter with some electrical load at the output may require less time for simulation then
an inverter driving a motor. It is because the inverter has a time constant in microseconds whereas a motor can not respond so quick so it has a response time in seconds. So
for accurate simulation it is mandatory to keep the step size much smaller that has a
side eect of longer simulation time. Further in power electronics we have to essentially
deal with power switches like MOSFETs, IGBTs, SCRs and diodes. Unfortunately no
accurate model is available therefore that makes it dicult to model them. Specic
requirements can be met only with careful objective based simulation. Since, power
electronics needs a controller therefore sophisticated controllers are modeled along with
to verify the exact system response. Inductors and capacitors used in power electronics
circuits may have some initial states that can hamper the swiftness of simulation. Therefore what we need is to carefully analyze what to achieve from a simulation.Sometimes
we may not need all the responses from a circuit. A good simulation can be dened as
following [6]
The best simulation is the simplest possible simulation that meets the immediate
objective
Therefore we need to specify the system objectives before simulation. For a detailed
system design following steps are followed [6]
Low level simulation or large signal simulation
Small signal model and controller design
High level simulation or large signal system behavior
Usually for initial testing of new system and for choosing the circuit topology controller
is not included in initial level simulation. Predened signals are given to the system to
observe the response. The observations from such low level simulation is then tested
with analytical calculations. This gives an idea about the component ratings and circuit
topology. Normally we need not to use detailed models for devices used at such low level
simulation. Ideal components are used to get a bird eye view of system performance.
Page 2

After deciding the type of circuit the next step is to include the design of controller.
Component values are also specied to create a linear model. Controller design may
include Proportional (P), Proportional Integral (PI) or Proportional Integral Derivative
(PID) control and may be strengthened by use of Fuzzy Logic (FL), or Articial Neural
Network (ANN). The complete design of controller makes it sure to proceed for the high
level simulation where it is combined with the circuit to verify the performance of the
designed system. At this stage the power losses, heat curves and non linear behavior is
also studied in detail. The details of voltage stress on switching devices, the eect of
stray capacitances and leakage inductances are also incorporated in this stage to get a
response closer to the real world. At this stage ideal models are not used , rather we use
detailed models to show the system nonlinearities explicitly. The bottom line here is
Simulation makes it easier to nd design problems early in the design cycle.
1.2 Why Simulink

SIMULINK is available with MATLAB installation and unlike MATLAB it is a model
based software, i.e. it models the system with the help of building blocks and small
elements and then simulates for the analysis of the model. It is so simple that making
a system is not more than plug and play. You put your desired building blocks on
the blank model page, x their values and connect the output to a scope to see the
eect. Various kinds of building blocks are available within SIMULINK ranging from
the simple to advanced one based on articial intelligence techniques. Both linear and
non linear systems can be modeled in it with the same ease. The analysis could be of
dynamic system and can be of any level. The main idea behind every simulation is to
model the system. It can perform mathematical modeling as well as real component
based modeling. The ongoing research in the eld of engineering has proved that the
SIMULINK results are very promising and resembles too close with the real system
provided that the modeling is accurately accomplished. The models can be made in
accordance with the simulation guidelines given in section 1.1. The model once made
can be modied with real values of components. It can be used for the simulation of
following systems
Continuous timed model
Sampled timed model
Hybrid system with both continuous and sample time modeling
Linear system
Non-linear system
With the time, SIMULINK has become so mature in its work that now a very large
portion of research work is based on the simulation results of SIMULINK. Since the
main computational engine used is MATLAB therefore SIMULINK allows you to use the
Page 3
1.3 SIMPOWER SYSTEM

MATLAB functions to work in parallel with the SIMULINK model. Even the MATLAB
function can be made as part of the SIMULINK model. Engineers and scientists are
using this to testify their theoretical hypothesis and novel techniques and its outcome is
saving a lot of time and money. SIMULINK is widely used in the following areas [2]
Aerospace and defense
Automotive
Power system analysis
Power electronics and renewable energy system simulation
Articial intelligence based systems
Communications
Electronics and signal processing
Medical instrumentation
As this book is on the simulation of power electronics therefore we will focus on one of
the functionaries of SIMULINK known as SIMPOWER system.
1.3 SIMPOWER SYSTEM

SimPower Systems software is a very useful tool for the analysis of power system problems. It has produced a lot of ease for engineers and researchers for in depth analysis of
power system using its user friendly interface. As discussed above the work of SIMULINK
is merely a plug and play operation therefore SimPower Systems is easy to use and models can be developed using simple click and drag procedures. SIMULINK is used for
variety of systems and SimPower Systems being an integral part of SIMULINK provides
and opportunity to develop a whole industrial environment with thermal, mechanical
and control blocks connected with the electrical system. In SimPower Systems software
the electrical components are present that can be adjusted to model a specic device.
For example transformer has built in data that can be modied for the input and output
values by simple clicking and editing the value. Besides the transformer SimPower Systems has other components like transmission lines, electrical machines, wind generation,
HVDC and electric drives. For simulation of power electronics systems a semiconductor based library lies within the SimPower Systems. Measurement library allows the
researcher to measure various parameters like current, voltages, power, THD, RMS, and
impedance for single and three phase systems. Input can be selected by a mix library of
input sources that includes the AC and DC voltage and current sources. Very interestingly the POWERGUI block makes it fun calculating the FFT of the waveform at any
instant and any particular point. By selecting the fundamental frequency and the limit
for harmonic analysis one can see details of harmonic pollution within a model in both
graphical and tabular form. People have spent years on the research and development
Page 4

of these components therefore, these models are proven and are tested in reputed laboratories including Power Systems Testing and Simulation Laboratory of Hydro-Qubec,
a large North American utility located in Canada, and also on the experience of cole de
Technologie Suprieure and Universit Laval [2]. The capabilities of SimPower Systems
software for modeling a power electronics system are presented in this book with a lot
of graphical illustrations.
1.4 Architecture of book

Power electronic is a science of power conversion. There are four types of power conversion within the domain of power electronic conversion. These include
AC-DC conversion (Rectiers)
AC-AC conversion (Cycloconverter)
DC-AC conversion (Inverter)
DC-DC conversion (Switch Mode Power Supplies)
In this book the topic of rectiers has been divided into two parts with simulation of
controlled and uncontrolled rectiers. Dierent topologies for single and three phase
rectiers are simulated using free wheeling diode and without using freewheeling diode.
A little theory has also been given for each circuit assuming that the reader know well
about the working of these circuits. Chapter on cycloconverter has two simulations for
single phase to single phase and single phase to three phase cycloconverter with step
down feature. We have tried to cover inverters with detail especially the single phase,
three phase, quasi square wave and SPWM inverters. Last chapter is about DC -DC
converters. All the basic types are simulated and in addition to them the concept of
unipolar and bipolar output has been elaborated using simulation of full bridge DC-DC
converter.
Page 5
2.1 Introduction
Most of the power electronic devices converts the incoming AC voltage of xed frequency
and xed voltage into DC of xed value. The objective here is to obtain useful DC supply
from grid side. Diode based rectiers are used commonly for such purpose. They are also
known as uncontrolled rectiers. In these type of rectiers the power can only ow from
AC side to the DC side hence, we do not have any control on the power ow. The output
is entirely dependent on circuit topology and the biasing condition of diodes. As soon
as the applied voltage exceeds the diode depletion layer potential (typically 1-2 V for a
power diode and 0.7V for ordinary Si diode and 0.3V for ordinary Ge diode) it starts
conducting and keeps on conducting unless and until the voltages becomes less then
the required threshold voltage. Since, everything that happens in this entire process is
automatic and no external parameter can control the power ow therefore such rectiers
are called uncontrolled rectiers. These kind of power electronic devices are also known
as linear power supply and suer from their large size and low eciency. However, these
type of rectiers are widely used in single and three phase domestic applications. In this
chapter we are presenting the simulation for both single phase and three phase rectiers
with various congurations.
2.2 Single phase half wave rectier

Single phase half wave rectiers are the most basic form of rectier. A rectier without
having any control on power ow is based on diodes. These diodes turn on and o
according to the voltages available on their terminals. They cannot be controlled through
some external signal. The term half wave is originated from the fact that these rectiers
only allow half wave to appear across the load. Half of the cycle always drops across
the diode. They have the least number of diodes in their topology that results in poor
power quality, increased voltage drop and less power utilization. They typically have an
eciency of 41 % and a ripple factor of 121 %, therefore such type of rectiers are not
used in practical applications. Since this kind of rectier is a basic building block for
the theoretical advancement in diode based rectiers it is simulated for RL load.
2.2.1 Without freewheeling diode

The single phase half wave rectier is shown in Fig.2.1. It has only one diode that allows
to pass only one half cycle of input AC voltage and blocks the other half. The part of
cycle it blocks depends on the connectivity of diode with input supply. These kind of
Page 6
converters have a xed output and a low eciency due to the wastage of half the supply
voltage.
Figure 2.1: 1 half wave rectier with RL load
Simulation Procedure
We will now simulate this circuit using the following values of circuit components
Resistance = 0.5
Inductance = 6.5 mH
Vin =220 Vrms at 50Hz (312Vp )
Open MATLAB and click on the icon for SIMULINK as shown in g.2.2. Alternatively
you can open SIMULINK by writing SIMULINK in the command window. Another
way is to adopt the way through START icon of MATLAB Start Simulink
Librarybrowser. Click on NEW MODEL or go to F ILE N EW M ODEL and a
new blank model is created as shown in Fig.2.3. You can also reach this point directly
by adopting this route M AT LAB F ile N ew M odel. However, after creating
a blank model you need to open the SIMULINK component storeroom by going to
V iew LibraryBrowser. Select SIMPOWER SYSTEMS then select Power Electronics
library and by right clicking on diode and click on add to untitled will add the diode
in the blank model. Alternatively you can drag the component directly in the model
page as shown in Fig.2.4. Similarly go to ELECTRICAL SOU RCES AC Voltage
Source and add it to untitled. Select Elements and select SERIES RLC BRANCH and
add it to untitled. Simulink do not perform simulation unless and until a measurement
block is present in a system. Since we need to measure the instantaneous input and
output voltages and the load current we need to have 3 instruments (2 voltmeters and
1 ammeter). To add them select Measurement in SIMPOWER SYSTEMS and then
Page 7
Figure 2.2: Reaching simulink
add current measurement and voltage measurement blocks to untitled. Oscilloscope is

not included in SIMPOWER SYSTEMS and is present in the top most block of the left
column that is SIM U LIN K Sinks Scope. We can join various blocks by clicking
on their edges and then drag the wire till the other connection terminal. Construct the
circuit by joining them together in the form as given in Fig. 2.5
Page 8
Figure 2.3: Creating a new model
Figure 2.4: Adding a block in the model
Page 9
Figure 2.5: Construction of a model
Page 10
Figure 2.6: Voltage block
Now double click the voltage block to set the values of voltage and frequency. A dialog
box will appear as shown in Fig.2.6. Inside it various parameters can be set that are
Peak amplitude of the generated voltage, in volts (V)
Set it to 312 V (Default is 100V)(.

Phase in degrees (deg).
Set it to zero (0) degrees.

Frequency in hertz (Hz).
Set it to 50Hz (Default is 60Hz)

Sample time in seconds (s). The default is 0, corresponding to a continuous source.
Let it remain as it is
Measurements
Set it to none because we are not using multi meter (Use of multi meter is
discussed in comming simulations).
Double click on diode and you can set various parameters for DIODE according to the
specic data sheet. Double click on series RLC branch and set the values for R and L
Page 11

as given in the start of the problem. Select the Branch type as RL as shown in Fig.2.7.
It should be noted that for writing the values of L we have to use e-6 for micro and e-3
for milli etc.
In the Scope menu > is shown which can only be connected to the inverse icon <
in the measurement blocks. It has only 1 input terminal. When we need to observe the
waveforms we use scope and if the resultant waveforms are more than one then there
are several methods to display all the three waveforms as given below
Use separate scopes for all the measurements.
Use MUX before the scope.
Adjust the number of axes of scope.
We will adopt the third method. Double click on SCOPE and then click on parameter
icon as shown in Fig.2.8. Make the number of axes equal to 3. Now you can observe that
we have 3 axes that can be used for the three plots as required in problem statement.
Before simulation also adjust the data history of scope by following the Fig.2.9. By
checking the save data to history we can perform the fourier analysis of the waveforms.
You can also remove the limit data points.... by unchecking it.
Page 12
Figure 2.7: Load selection
Figure 2.8: Adjusting the oscilloscope
Page 13
Figure 2.9: Adjusting the oscilloscope parameters
Page 14
Before running the simulation we have to congure the parameters. Go to Simulation
Conf igurationparameters as shown in Fig.2.10. Various kind of solvers are available
for simulation. Each solver uses dierent techniques for solving the system based on sti
and non sti problems. Among the available solvers given below rst four are considered
good for non-sti problems. Rest all are for sti problems [5, 7],
ODE45
It is based on Dormand-Prince which is explicit, one step Runge-Kutta recommended as a rst try method.
ODE23
It uses Bogacki-Shampine that is also explicit, one step Runge-Kutta. May be

more ecient than ODE45 when tolerances are wide.
ODE113
It is multi step, variable order Adams-Bashforth-Moulton PECE solver.When

function evaluation is time consuming and tolerances are tight it is recommended
ODE23t
It is used for moderately sti problems if you need a solution without numerical
damping.
ODE15
Multi step variable order solver based on backward dierentiation formula

ODE23s
One step solver based on Rosenbrock formula of order two. It has the A
stability property.
ODE23tb
It is also for sti problem and can be used for using curde error tolerances to
solve sti systems
Select the ode23tb (Sti/TR-BDF2) or ode15s (Sti/NDS) or any suitable solver as
shown in Fig. 2.11. ode15s (Sti/NDS) is used for simulating this circuit.
Start the simulation by either clicking on Start Simulation icon as shown in Fig. 2.4 or
by going to Simulation Start.
Page 15
Figure 2.10: Getting towards the simulation parameters
Figure 2.11: Adjusting the simulation parameters
Page 16
Results
Double click on scope and observe the three graphs as shown in Fig. 2.12. Left click on
any graph and drag to make a rectangle to get the waveforms for a small period of time.
This actually zoom the waveforms within a specied interval of time. Right click on each
graph and select the axes properties and label each graph. As shown in Fig.2.5 double
click on power GUI and click on FFT analysis. Figure 2.13 shows the FFT window. Set
fundamental frequency as 50 Hz and click on display. The results can also be obtained
in term of tabular form by selecting the display style in FFT window.
Save the le as half wave. It should be noted that simulink do not allow to save les
with spaces therefore usually is included in between two words.
Page 17
Figure 2.16: FFT of the rectier with free wheeling diode

2.3.1 Without freewheeling diode
Full wave rectiers are a rened form of the basic rectiers and are widely used for
low power applications like battery chargers, DC power supplies and computer power
supplies. They are also uncontrolled hence the quantity of the output cannot be controlled. The center tap rectier uses a center tapped transformer and it has only two
diodes to conduct in alternate paths. Figure 2.17 shows the schematic of a center tapped
rectier. The transformer used is center tapped and have two secondary windings with
their center tapped. The central end is connected to ground and the other two ends are
connected through each other via diode D1 and D2. The diode D1 conducts when there
is a positive voltage at the transformer secondary winding. However while D1 conducts
there is a negative voltage at the anode of D2 so it acts as an open circuit. D2 conducts
when it gets a positive voltage at the anode. When it conducts then at that time D1
will act as an open circuit. So in this way it recties both the portions of input cycle. In
this method the transformer is used and only two diodes are used for the rectication.
We will now present the simulation of this circuit using an RL load.
Simulation Procedure
Create a blank page and add the following blocks
Page 20
Figure 2.17: Circuit arrangement for single phase full wave center tap rectier
SimPower SystemsElectrical sources AC voltage source

SimPower SystemsElements Linear transformer
SimPower SystemsPower electronics Diode
SimPower Systems Elements Series RLC branch
Arrange the circuit as shown in g 2.17. The center tapped transformer here is used as
a step down transformer with 12 volts set at the secondary. For having teo secondaries
check the Three winding transformer option given in transformer parameter dialog
box. To set the parameters of this transformer double click on it and enter the value of
input voltage and frequency as shown in Fig. 2.18. The rest of the circuit is very simple
and can be completed by following the rules mentioned in the previous topic.
Results
The waveforms for the above circuit are given in Fig.2.19 and it is very visible that both
the positive and the negative half cycles are rectied using this circuit.
Page 21
2.5 Three phase full wave rectier
Figure 2.28: Simulation setup for three phase full wave rectier
Voltmeter (Simulink Sim Power system Measurements Voltmeter)

Diode ( Simulink Sim Power system Power electronics Diode)
Ground (Simulink Sim Power system Elements Ground)
Multimeter Block (Simulink Sim Power System Measurement Multimeter
)
Mux (Simulink Commonly used blocks Mux)
Assemble the circuit as shown in Fig. 2.28. Double click power GUI and click on
congure parameters. Select simulation type as discrete with sample time of 50e-6. Open
the scope and go to parameters. Select sampling as sample time and make it similar to
the value selected in GUI block (50e-6). To make a three phase supply join the three AC
voltage source as shown in Fig. 2.28 and enter 0,120 and 240 (or -120) in phase tab of each
source respectively. The resultant 3 phase waveforms are shown in Fig.2.29. Connect the
negative terminal to ground. In order to get the line voltage use voltmeter and connect
them to get Vab , Vbc and Vca . It should be noted that Vab = Va Vb , Vbc = Vb Vc and
Vca =Vc Va . Set the value of RLC series branch as RL load with R = 1 ohm and L =
1e3 H. Also select the branch voltage and current in measurement tab. Before running
the circuit make sure the following
Set the solver as ode23tb (sti/TR-BDF2)
Max. step size as 0.001
Double click on multimeter and within the dialog box that will appear, the list on left side
contains the available measurements. Select them and add them in selected measurement
as shown in Fig. 2.30. It should be noted that if we uncheck the measurement tab in
RLC series branch then there will be no available measurement in multimeter.
Page 28
Figure 2.29: Three phase balanced input
Results
Run the simulation for 0.5 sec time Fig. 2.31 shows the output where it can be seen
that current and voltage across the load have phase dierence.
2.6 Twelve pulse rectier

So far we have simulated those rectiers that are most suitable for o line domestic
applications. The most powerful among these rectiers is the three phase full wave
rectier that is also referred as six pulse rectier. These rectiers have high THD for
inrush current and if we need to use them for very high power applications they are
considered inappropriate. This is specically evident in case of HVDC systems, where
we need to keep the THD of input current as low as possible and on the other side the
DC link ripple as minimum as possible. For such high power applications,one method
is to use a combination of two six pulse rectiers connected in delta-wye ( Y ) and
delta-delta( ) connection. The use of and Y at the secondary of transformer
gives a delay of 30 at the secondary. For coping with the high power requirement
the secondary can be connected in series or parallel for high voltage and high current
applications respectively. The main advantage is revealed in the fourier analysis of input
line current that states that the lowest order harmonic that appear are 11th and 13th [6].

For simulation place the following components as shown in Fig. 2.32.
AC voltage source
Three phase transformer, three windings (SIMULINK SIM POWERSYSTEMS
Elements Three phase transformer, three windings)
Diodes
Series RLC branch
Page 29
3.1 Introduction
Controlled rectiers are kind of rectiers that employee thyristors or SCRs. By using
these generic devices the output can be controlled by varying the ring angle. These
type of rectiers provide us some degree of freedom depending on the circuit topology.
Following are the dierent types of controlled rectiers
Half controlled rectiers
Full controlled rectiers
These type of rectiers are applicable for both single and three phase applications. They
form the basis for the four quadrant operation. With it we can design exile power
electronic systems for electric drives and other applications. In the coming sections we
will simulate various types of controlled rectiers.
3.2 Single phase half wave controlled converter

Single phase half wave rectier is the most basic kind of controlled rectier using only
one SCR. Only positive half cycle is used hence the power utilization is minimum. The
ripple voltage contains high harmonics and for such harmonics the current drawn by the
load inductance L will be less. Since the output voltage should not be rich in harmonics
therefore this kind of controlled rectier is seldom used practically and is given in text
books for understanding of basic concepts. Figure 3.1 shows the architecture of this
simple controlled rectier. Here the point where current goes to zero or where SCR stop
conduction is not in our control so we do not know the output ripple across inductance.
Since we have negative conduction here so we should get rid of the negative conduction
portion due after . Also in case of a highly inductive circuit the inductance L will not
allow the current to change instantaneously. So if we want to have eq.3.1 valid here we
have to remove the negative side.
Vo =
Vm
(1 + cos)
2
(3.1)
Therefore we need another part to be installed and there comes the concept of free
wheeling.
Page 34
If the gate pulses are applied at zero degree then this circuit is similar in operation to
a three phase diode bridge rectier. The output voltage obtained is a dierence of the
voltage at positive and negative rail. The supply current is a rectangular waveform with
only non triplen odd harmonics present in them. It should be noted that if we replace
the lower side SCRs i.e T2, T4 and T6 with diodes then the circuit works as a three
phase full wave semi controlled converter. Its simulation is left as an option for the
reader.

Place the following components as shown in g. 3.13.
Thyristors
Pulse generator
AC voltage source
Current measurement
Voltage measurement
Series RLC branch
Scope
Connection port(Simulink SIMPOWER systems Elements Connection
port)
Here three phase input is created by making a subsystem and the output of the subsystem
is connected with the bridge. Three pulse generators are used for ring of all six SCRs.
They are red at 45 with an additional phase delay of 120 and 240 for phase B and
C respectively. The load is taken as highly inductive with R=50 and L=650mH.
3.5.2 Results
For this circuit the waveforms for output voltage, the line current for phase A and the
FFT of the input current are drawn. Figure 3.14 shows the output voltage at = 45 .
Whereas Fig.3.15 shows the line current for phase A and its FFT. It can be seen that
only non triplen odd harmonics are present here.
Page 43
4 DC-AC Inverters
4.1 Introduction
DC-AC inverters are used mostly in applications where we need to have a variable
frequency with either DC or AC input voltage. Typical examples of inverter use are
motor drive applications, Uninterrupted Power Supply (UPS), Renewable energy systems
(Solar PV and Wind) and HVDC link, where the desired task is to generate the frequency
of user choice. Inverters are available in a variety of topologies for three phase and single
phase applications. Figure 4.1 shows the general schematic of a 3 phase inverter1 .
It is fed by a DC source that can either be supplied by rectifying the oine power supply
of utility or by other means like using a DC battery as in case of hybrid vehicles or the
output of a solar array in case of a solar system. For single phase inverters there are
four switches for a full bridge inverter and six switches in a 3 phase inverter. The output
voltage waveform for a voltage source inverter and output current waveform of current
source inverter are stepped waveforms and their quality depends on the switching scheme
of Pulse Width Modulation (PWM). Generally sinusoidal PWM is used for periodic
switching of the inverter switches. For analysis in almost every text book the DC link
is divided into two capacitors each holding half of the DC link voltage such that their
mid point becomes at zero potential as shown in Fig 4.1. The power ow in each phase
is controlled by the ON/OFF ratio or duty cycle of the respective switches. In the
operation of inverter some important relations are
Vao = Van + Vno
(4.1)
Vbo = Vbn + Vno
(4.2)
Vco = Vcn + Vno
(4.3)
Van + Vbn + Vcn = 0
(4.4)
3Vno + 0 = Vao + Vbo + Vco
(4.5)
1
Vno = (Vao + Vbo + Vco )
3
(4.6)
For balanced load phase voltages
Adding these equations, we get
PROJECT SPACE VECTOR PWM INVERTER by JIN-WOO JUNG Ohio State University, USA
Page 46
4 DC-AC Inverters
Figure 4.1: Typical three phase inverter [4]
Putting the value of Vno in Vao , Vbo and Vco we get

2
1
1
Van = Vao Vbo Vco
3
3
3
(4.7)
2
1
1
Vbn = Vbo Vco Vao
(4.8)
3
3
3
2
1
1
Vcn = Vco Vao Vbo
(4.9)
3
3
3
Since,most of the times inverters are used against the inductive load, in order to keep
the transistors safe, diodes are used in antiparallel direction for dissipating the energy
stored in the load inductance. Furthermore, the transistors connected in same leg should
never be turned on simultaneously so as to avoid any short circuit of dc bus bar. In this
chapter dierent types of single phase and three phase inverters are simulated. As PWM
is an essential ingredient of inverters the rst simulation is dedicated to the renement
of the concepts of PWM.
4.2 Pulse Width Modulation

PWM is one of the most widely used technique in power electronics switching. It is a
process of producing pulse trains with variable widths that control the ow of power
through power electronic switches. Various kinds of PWM techniques are available in
literature, from simplest to specialized one like Selected harmonic Elimination (SHE).
Figure 4.2 very clearly shows the simplest PWM scheme in which a triangular wave is
compared with a DC voltage. The amplitude of DC voltage is directly responsible for the
production of pulses with variable width. The output will be high if amplitude of DC is
greater then the amplitude of triangle waveform at any instant.It is obvious from the the
related gures that decreasing the amplitude of DC is actually generating pulses with
narrow pulse width and vice versa. It should be noted that the frequency of waveform
is independent of the amplitude of DC value. Mostly such kind of PWM is employed
in DC DC Converters where the DC is fetched from the output via a voltage divider
Page 47
4 DC-AC Inverters
Figure 4.3: Three phase sinusoidal PWM [5]
Page 49
4.2 Pulse Width Modulation
Figure 4.4: Generation of triangular waveform

We have to generate PWM using SIMULINK.Open the SIMULINK and create new page
and place the following blocks on the model page.
Constant
Integrator
Scope
User dened function f(n)
MUX
We have to rst generate the triangular waveform. To generate this following setup is
required as shown in Fig. 4.4. In Fig. 4.4 we have to write an M le and write the value
of e or alternatively we can enter its value equal to the desired value. The MUX can
have many inputs. In SIMULINK each input is designated as U1, U2, U3 up to Un. So
in our case the input from integrator is U1 and that of constant1 block is U2. In order
to produce a triangular waveform we have to take reminder in order to compare the ever
going ramp as shown in Fig. 4.5 .One more interesting block in this simple model is the
user dened function Fcn. Open Fcn block and write the following function
Rem(u(1),u(2))
It is evident from the Fig. 4.5 that using this function we can generate triangular
waveform. Next step is to compare this triangle waveform with a DC wave to generate
variable widths PWM pulses. Figure 4.6 shows the complete structure of simulation
setup for this simple PWM scheme. Comparing the triangular waveform with an AC
waveform gives us what is called Sinusoidal PWM.
Page 50
4.4 Single phase PWM inverter with bipolar voltage switching
4.3.1 Simulation procedure

To perform the simulation assemble the circuit as shown below in gure 4.10 using the
following components
DC voltage source (Enter any desirable value)
Multimeter
Series RLC branch
Sine wave source
Mosfet
Trignometric function
Gain
Rational Operator
Out port(Simulink Sinks Out 1)
It should be noted that a small resistance Rs is connected in series with the voltage source
Vdc . This is to take care of a simulink error that arises when we connect a capacitor in
shunt with the dc voltage source. For switching the power MOSFETs sinusoidal PWM
is used. It has two reference sine waves with 180 phase dierence. Figure 4.11 shows
the subsystem for PWM generation. The resultant PWM are feeded to the gates of
corresponding MOSFETs
4.3.2 Results
Figure 4.12 shows the output voltage and the FFT of the waveform for resistive load and
Fig.4.13 shows the output voltage and FFT of the waveform for highly inductive load.
It should be noted that 21 Vdc is available at the output and since it is an odd symmetry
therefore the even harmonics are clearly negligible in fourier spectrum.

Single phase inverters has two legs of switches that are connected in parallel with each
other. It is similar to the bridge rectier with the basic dierence of switches in place
of diodes. The switches are turned ON and OFF at specied pattern to produce AC
output. PWM used here works in such a way that we get bipolar switching voltage that
is the output voltage obtained is between +Vdc and Vdc .
Page 54
4 DC-AC Inverters
Figure 4.10: Simulation setup of single phase half bridge inverter

We have to simulate a single phase inverter with bipolar switching with single phase
Asynchronous motor as load and to plot the waveforms for output voltage, the fundamental component of output voltage, the current for the asynchronous motor and dc link
current. Open SIMULINK and create a new model and place the following components
according to the diagram shown in gure 4.14
Discrete PWM generator
Series RLC branch
Figure 4.11: Subsystem for PWM generation of single phase half bridge inverter
Page 55

DC voltage source
MOSFETs
Voltmeter, Ammeter ans scope
Discrete second order lter
Demux
Page 56
4.5 Single phase PWM inverter with Unipolar voltage switching
Figure 4.14: Simulation setup of single phase inverter with bipolar switching
It is chosen to work here as a bandpass lter with cuto frequency of 52Hz and damping
factor and the sample time are left as default. The output of the lter is merged with
the output voltage of inverter using a MUX and is fed to the scope. The motor used
here is an asynchronous motor with 14 hp,110V and 60Hz ratings. Figure 4.15 shows the
parameter adjustment window of an asynchronous motor. Note that for power the value
entered is 0.25*746 that is the desired value.
4.4.2 Results
Figure 4.16 shows the waveforms for output voltage, the fundamental component of
output voltage, the motor armature current and the DC link current.
4.5 Single phase PWM inverter with Unipolar voltage

switching
With a little modication of control logic the circuit used for bipolar switching inverter
can be used to get unipolar output. In this technique the output goes from +Vdc to
zero for positive half cycle and then from zero to -Vdc for the negative half cycle. That
is why it is called Unipolar voltage switching PWM. Thus the two legs on inverter are
controlled separately. Therefore, two control signals are to be used that must be 180
degree out of phase with each other. The advantage of this kind of PWM is that the
harmonics appeared are at side bands of twice the switching frequency.
4.5.1 Simulation procedure

We have to simulate a single phase full bridge inverter using unipolar voltage switching
PWM and plot the waveforms for Van , Vbn , Vab and FFT of the Vab . Crete a new page
and place the following components according to g.4.17
Page 58
4 DC-AC Inverters
Figure 4.15: Single phase asynchronous motor
Discrete PWM Generator

Series RLC branch
DC voltage source
MOSFETs
Voltmeter
Goto
From
Scope
Discrete second order lter
Demux
Page 59
4.8 PWM based DC-AC 3 phase Inverter

also known as tripplen harmonics. However, the fundamental components are summed
to zero provided that the operation is symmetric i.e.
V1ao + V1bo + V1co = 0
(4.14)
where 1 stands for the fundamental component There are topologies that do not have
neutral to get rid of tripplen harmonics. We have to plot the waveforms for eq.4.7, 4.8
and 4.9 for Fig.4.1. A good model is presented in B.K.Bose and we are using that model
with little bit modication in this experiment. Furthermore it is desired to perform the
Fourier analysis of these waveforms. It is also required to plot the current waveform in
each phase for Inductive load of 6.5 mH.

Open the SIMULINK and create new page. Place the following blocks on the model
page.
Three phase SPWM (refer to section4.2)
Switch
Scope
Gain
DEMUX
Integrator
Sum
In section4.2 we have successfully generated the three phase SPWM (also known as Sub
oscillation method) . Place it in the new model for this experiment. In order to model
the three legs of inverter we use the switch. For example consider leg A of Figure 4.1
with S1 and S4. We have to turn them ON in such a way that S1 and S4 can not turn on
simultaneously (Whats the reason?). Therefore it is evident that leg A can have only
one state at a time. Either it can provide positive Vdc to output or it can pass negative
Vdc to output. The switch we are using has three ports. It gives the output based on
the information given at the center input port. Figure 4.27 shows the model for three
legs of inverter with +500 Vdc and a -500 Vdc [1]. In this gure Pulse A , Pulse B and
Pulse C are the waveforms we generated in section4.2. In each phase leg top input is
connected to +500 Vdc and bottom input with -500 Vdc . The output of each phase leg
is Vao , Vbo and Vco for phase A, B and C respectively. Next we have to implement the
equations for Van , Vbn and Vcn . For this we need gain blocks and a sum block. For an
instance consider the following equation reproduced here for clarity
2
1
1
Van = Vao Vbo Vco
3
3
3
Page 68
(4.15)
4 DC-AC Inverters
We have to multiply Vao with 23 and Vbo and Vco with 13 . Then using sum block (double
click and then you can adjust the shape and list of signs which in our case is +) we
add them by giving 23 Vao to +ve and rest two to negative terminal. The output will be
the Van as desired in the problem statement. Since the load is inductive as stated in the
simulation procedure so we know that the relationship for current though the inductor
is given by

1
V dt
(4.16)
iL =
L
Page 69
4.8 PWM based DC-AC 3 phase Inverter
Figure 4.27: Modeling of leg of an inverter [1]
Page 70
4.9 SPWM based 3 phase inverter with 3 phase Asynchronous motor as load
Figure 4.29: Complete model of an inverter [1]
Therefore for getting

the current waveform across an inductive load we have to integrate
the voltages by L1 V dt. Figure 4.28 shows the model for implementation of Van , Vbn
and Vcn .
Figure 4.29 shows the complete model of the inverter that is a modied form of model
presented in the book Modern Power Electronics and AC drives by B.K. Bose.
4.8.2 Results
Figure 4.30 shows the voltage and current waveforms for all the three phases respectively.
It should be noted that current comes to steady state after some time and all the three
waveforms are 120 displaced with each other. In the rst 60 Vbo andVco are opposite so
they cancel each other. Only 32 Vao is available at the output. It should also be noted
that there is a change every 60 so it is also known as six step inverter. There are
5th , 7th and11th harmonics but no tripplen harmonic component is present. Figure 4.31
shows the FFT of the said system
4.9 SPWM based 3 phase inverter with 3 phase Asynchronous

motor as load
Sinusoidal PWM based inverter can be used for the controlled operation of an asynchronous motor. The model developed in the last experiment can be used to run a three
phase motor with little modication however in this section we will be using real components to model a three phase inverter. Apart from this a built in block for diode rectier
is also used to convert the incoming three phase AC into DC. We will plot the waveforms
Page 72
5 Cycloconverters
5.1 Introduction
A cycloconverter is a type of power electronic converter that converts the input frequency
at dierent frequencies without using a dual stage (AC-DC-AC) conversion process. It
is widely used in high power industrial applications. SCRs as well as IGBT can be
used in the implementation of cycloconverter. Today multi-megawatt, thyristors based
cycloconverter are widely used for driving asynchronous motors (up to 15,000kW) at
low speed typically from 0Hz to 20Hz [3]. They have been successfully utilized for
the operation of industrial drives specially in cement industry. They are also used in
aircraft for producing variable speed and constant frequency power generation. They
can be used to replace AC-DC-AC systems where the operation is a variable speed at
xed frequency. Here the input AC is converted into high frequency using a step up
cycloconverter and before feeding it to the load that high frequency link is connected
to a step down cycloconverter that convert it according to the load requirements. In
case of a DC input the step up cycloconverter, which is responsible for high frequency
generation, is replaced with an inverter that is designed to generate high frequency.
The load side part however, remains same [1]. Contrary to the dual stage conversion
process (AC-DC-AC) this works without a DC link thus nullifying the requirement of
bulky DC link capacitors. Cycloconverter can be designed using a bridge topology or
by using center tapped transformer. Two full wave fully controlled single phase bridge
circuits are connected in anti parallel direction. One act as a positive converter and
one as a negative converter so that we can control the voltage and current of both
polarities in the load. It should be noted that both of the converters are fed by the
same source. Figure 5.1 shows a single phase cycloconverter in bridge conguration and
Fig. 5.2 in center tapped conguration. Whereas Fig. 5.3 shows the waveforms of the
cycloconverter. Cycloconverter can control output voltage and frequency up to a certain
extent. So it can be used as an electric drive with constant V/f ratio in a small range. By
controlling the switching of the P and N converter (Fig.5.1) we can change the output
frequency and by changing the ring angle we can control the output voltages. Hence
it can somehow make the torque constant in a specied degree of freedom. However
the ring pulses in both the P and N converter should be at the same angle to produce
symmetric output. There must be a delay in switching the P and N converters, switching
them simultaneously will create a dead short circuit. Therefore when one converter is
switching the other must be inhabited. In literature such kind of operation is referred
as circulating current free mode. In this chapter our main aim is to describe some
brief methods of simulating the basic cycloconverters. We will stick to the basic type
of cycloconverters such that on those basis the advance type of cycloconverters can be
Page 80
5 Cycloconverters

In these type of cycloconverters the input and output both are single phase and the
output has less frequency then the input hence called step down cycloconverters. Figure
5.1 and 5.2 shows the general connection scheme of single phase to single phase cycloconverter. It can be seen that they are merely just the connection of two single phase
controlled converter connected in antiparallel direction so as to utilize both the cycles
of input waveform. Each converter in Fig.5.1 is designated as P and N that tells that
positive and negative output can be obtained by their stand alone operation, i.e we get
positive output if only P is red and negative output if we re only N. Similarly as shown
in Fig.5.2 the correct ring of pairs gives positive and negative outputs. By sequential
switching of converter pairs we can get low frequency at the output. So if the total time
is To then the output frequency is T1o if and only if the pairs of switches or the P and N
converters are turned on for T2O . The output of both positive and negative converter are
equal in magnitude and opposite in polarity. Referring to Fig.5.1 the triggering pulses
for the SCRs are given such that during the positive half cycle of input the P converter
is turned on and if we need a voltage control then T1 and T2 are red at and the
remaining two switches in P converter (T3 and T4) are red at + . For the negative
half cycle of input P converter is isolated and the negative converter works to give the
output. The voltage control should be achieved for same ring angle to get symmetrical output as discussed above. Here T1 and T2 are red at and T3 and T4
are turned on at 2 .

We have to generate a frequency of 5 Hz from 50 Hz power supply with the help of
cycloconverter keeping the voltage level constant. Then plot the waveform for voltage
and current for a resistive load. Open the SIMULINK and create new page. Place the
following components as shown in Fig. 5.4
Ideal switches
Thyristors
Series RLC branch
Multimeter
Pulse generator
NOT gate
Goto (Simulink Signal Routing Goto)
From (Simulink Signal Routing From)
Scope
Page 83
Figure 5.4: Simulation setup of a single phase to single phase step down cycloconverter
There are two bridges that are connected to load through 4 ideal switches (IGBTs in
practical scenario). The two clock sources are used in ring the thyristors. In order to
get the same output voltage we have to switch all the thyristors at 0 degree i.e all the
thyristors will act as diode. The change in frequency is generated by the switching of
ideal switches. The clock feeding the pulses to ideal switches is set at 1 V, frequency of
5.15 Hz and duty cycle of 50% (S1 and S3). The output is 180 degree phase shifted (S2
and S4) to avoid short circuit. The clock for T1, T4, T5 and T8 have an amplitude of 1
V and a frequency of 50 Hz. With pulse width 5%. Same clock properties are provided
to thyristors designated as T2,T3, T6 and T7. Using the Goto and From blocks we
can get rid of the nasty routing. Select the Goto block and connect it with the signal
generator. Double click theGoto and tag it as you like .e.g. let it be A1. Now in order
to route its signals we will use the block From . Attach the From blocks to the gates of
switching devices (T1, T4, T5 and T8) and tag it with the same name as A1. In this
way all the signals are sent to their destinations. It should be noted that if there is a
subsystem in the model then you have to modify the GOTO and FROM properties. In
that case we have to select global visibility. Connect all the clock signals to respected
switching devices using these blocks. For measurement we are using Multimeter. Place
a Multimeter and connect it with scope. Now in order to measure the branch voltage
and current of load double click on load (RLC series branch in this case). A dialogue
box will appear as shown in Fig. 5.5. Since we want to measure the branch voltage and
current so we will select it. Now we will double click the Multimeter and you will see the
available measurements . Select all the desired measurements and add them. In order
to view the plot of measurements we have to check the Plot selected Measurement as
shown in gure 5.6. The input voltage is set at 100 V 50 Hz.
Page 84
5 Cycloconverters
Figure 5.5: Selection of measurements
Figure 5.6: Plotting of measurements
5.2.2 Results
Figure 5.7 shows the branch voltages and Fig. 5.8 shows the branch current. It can be
viewed that the output frequency is 5 Hz.
Page 85
Page 86
5 Cycloconverters

Three phase to single phase cycloconverter is same in working as that of the single phase
to single phase cycloconverter discussed in section 5.2 with the only dierence of multiple
phases in the input. The point of interest here is to generate the pulses for three phase
converter. The load is connected at the point of common coupling of P and N converter
with other side connected to ground. Figure 5.9 below shows the general schematic of
this converter. The simplest cycloconverter is the envelope cycloconverter whose output
is made up of whole number of half cycles of supply waveform. By controlling the point
on wave at which the individual phases are switched we get an output voltage waveform
in which the fundamental is emphasized. Remember, by increasing the pulse number
of the cycloconverter the output can be made much more closer to the sine wave. The
peak output voltage that a cycloconverter can provide depends on the DC bus voltage
that each converter can produce. For a cycloconverter of an n number of pulses and
ignoring overlap
n
o
(5.1)
= sin Vpeakin Cos
Vpeak
n
The ring angle of individual thyristors in the cycloconverter is determined by reference
to the instantaneous value of output voltage required. Firing angle can then be calculated. Three phase to single phase cycloconverter are superior in performance then the
single phase to single phase cycloconverters. They can deliver more power to load and
have less ripple.

We have to generate a frequency of 10 Hz from input power supply of 50Hz with the
help of cycloconverter. Then plot the waveform for voltage and current for a resistive
load. Open the SIMULINK and create new page. Place the following components as
shown in Fig. 5.10
Ideal switches
Thyristors
Series RLC branch
Multimeter
Pulse generator
NOT gate
Goto
From
2nd order lter(Sim power System Extra Library Control blocks 2nd order
lter)
Page 87
5 Cycloconverters
Figure 5.10: Simulation setup for 3 phase to 1 phase cycloconverter
Figure 5.11: Timing diagram of pulses
Page 89
Figure 5.12: Output without lter
Figure 5.13: Output with lter
Page 90
6 DC-DC Converters
6.1 Introduction
DC DC converters are also known as switch mode power supplies and are widely used in
power electronics based systems due to their superior performance in term of eciency,
as compared to the linear power supplies. They are capable of step up/down the input
DC voltages. They are also capable of generating multiple output dc voltages. Moreover
the output can be isolated from input. Power transistors used in SMPS are operated in
the most ecient mode that is in saturation and cut o region. Switching frequency is
very high as compared to the linear supplies (power frequencies) thus, decreasing the size
of the output lter capacitor. The magnetic and capacitive elements are much smaller
then linear power supplies. However they are complex in designing and considerable
high attention in required to get rid of the high frequency noise. Basic topologies are of
three types.
One which step down the input DC voltages ( Buck Converter)
One that steps up the input DC voltages (Boost Converter)
One that ca step up and step down the DC voltages ( Buck/Boost Converter)
The ingredients of designing the most basic circuit for the three kinds of converter are
Power Transistor
Diode
Inductor
Capacitor
The output can either be stepped up or down by dierent combinations of the above
components.
6.2 DC-DC Buck Converter

Figure 6.1 below shows the basic buck converter. Buck converter steps down the DC
voltage. Here when the transistor is turned on the input voltage is applied to the inductor
and diode act as open circuit. When the transistor is turned o the inductor reverses
its polarity and makes the diode forward biased thus making a loop of current. The
voltage transfer ratio is dependent on the duty cycle and can be max to 1 as evident
Page 91
6 DC-DC Converters
Figure 6.2: DC-DC buck converter simulation setup
6.3 DC-DC Boost Converter

Figure 6.4 shows the basic boost converter. Boost converter is also known as ringing
choke converter. It is called boost converter since it steps up the input DC voltages.
Here when the diode is reversed biased the inductor stores energy from input. With
transistor T o the inductor changes its polarity to keep the current owing in the same
direction thus making the total voltage across the Transistor Vin + Vl , thus according to
equation 6.2
(6.2)
Vo = V in + Vl
Where
Vo = Output voltage
Vin = Input voltage
Vl = Voltage across inductor
Equation 6.2 clearly shows that the output voltage is always greater then the input
voltage. Inductor stores energy during the ON time of transistor. Whereas, during the
ON time output capacitor supplies energy to the output circuit. In terms of the duty
cycle the voltage transformation ratio is given by
1
Vo
=
V in
1D
(6.3)
Where,
0 D 1
Equation 6.3 depicts that the output is solely dependent on duty cycle and will theoretically tends to innity with D equals to 1. However, practically there is always some
conduction losses in real components.
Page 93
6 DC-DC Converters
Figure 6.5: DC-DC boost converter simulation setup
6.3.2 Results
Figure 6.6 shows the output current while Fig. 6.7 shows the input and output voltages.
It is visible that the output voltage is greater than the input voltage
6.4 DC-DC Buck / Boost Converter

One type of DC-DC converter can either buck or boost the input voltages. It is called
buck/boost converter. It is also known as polarity inverting converter and is use in
applications up to 200 watt. It is used where we need to reverse the polarity. Figure
6.8 shows the basic structure of buck/boost converter. When T is ON the input voltage
is applied to inductor L and capacitor C supplies power to load. When T is OFF the
inductor reverses its polarity and forward bias the diode D and will supply the energy
to output. The duty cycle decides the operation as buck or boost. When
For D = 0 to 0.5 operation is of buck converter
For D = 0.5 to 1.0 operation is of boost converter
Theoretically at 1 the output must be innity, but in practical it is limited by the losses
due to switching and circuit components. At a duty cycle of 50 % theoretically, the
output is equal to input.

We have to simulate a buck/boost converter capable of buck/boost 10V input. Plot the
waveforms for input and output voltages at duty cycle of 25%, 50% and 75%. Open the
SIMULINK and create new page. Place the following components as shown in Fig. 6.9
Page 95
Figure 6.6: DC-DC boost converter output current
Figure 6.7: DC-DC boost converter simulation results
Mosfet
Series RLC branch
Voltmeter
Pulse generator
Scope
Adjust the values of L as 500 mH and C as 2500 F. Load resistance is taken as 100.
Switching time can be set through the pulse generator and it is set as 0.009sec.
Page 96
Figure 6.10: Simulation results with 25% duty cycle
Figure 6.11: Simulation results with 50% duty cycle
Page 98
6.6 Full Bridge DC DC Converter
Figure 6.23: Simulation results for unipolar voltage switching
Page 108
Bibliography
[1] B.K.Bose. Modern Power Electronics and AC drives. Pearson Education, 2006.
[2] Simulink Help. Simulink help as given within the software.
[3] H.Rashid. Power Electronics Circutis Devices and Applications. Prentice Hall Int.
Ed., 1993.
[4] Jin-Woo Jung. Project Space Vector PWM inverter.
[5] Matlab. www.mathworks.com/help/techdoc/ref/oder23.html.
[6] T. Undeland N.Mohan and W.P.Robbins. Power Electronics Converters, Applications and Design. Wiley India, 2006.
[7] Chee-Mon ONG.
Dynamic Simulation of Electric Machinery using MATLAB/SIMULINK. Prentice Hall, 1998.
Page 109
Buy your books fast and straightforward online - at one of worlds

fastest growing online book stores! Environmentally sound due to
Print-on-Demand technologies.
Buy your books online at
www.get-morebooks.com
Kaufen Sie Ihre Bcher schnell und unkompliziert online auf einer
der am schnellsten wachsenden Buchhandelsplattformen weltweit!
Dank Print-On-Demand umwelt- und ressourcenschonend produziert.
Bcher schneller online kaufen
www.morebooks.de
VDM Verlagsservicegesellschaft mbH
Heinrich-Bcking-Str. 6-8
D - 66121 Saarbrcken
Telefon: +49 681 3720 174

Telefax: +49 681 3720 1749
info@vdm-vsg.de
www.vdm-vsg.de

Simulation of Power Electronics Circuits Using SIMULINK

Uploaded by

Copyright:

Available Formats

Simulation of Power Electronics Circuits Using SIMULINK

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Simulation of Power Electronics Circuits Using SIMULINK

Uploaded by

Copyright:

Available Formats

What are some of the different types of DC-DC converters discussed?

What are some of the different types of DC-DC converters discussed?

How does the duty cycle affect the output voltage of a DC-DC converter?

How does the duty cycle affect the output voltage of a DC-DC converter?



       

/    

 !  "  

4& )*5/ +)

Simulation of Power Electronics Circuits

Hadeed Ahmed Sher

Dedicated to my Wife and my family

DC-DC Boost Converter . . . . . . . . . .

1 half wave rectier with RL load . . . . . . . . . . . . . . . . . . . .

Single phase half wave controlled rectier . . . . . . . . . . . . . . . . . .

Typical three phase inverter [4] . . . . . . . . . . . . . . . . . . . . .

Simulation setup of hysteresis band inverter . . . . . . . . . . . . . . . .

General diagram of a cycloconverter [3] . . . . . . . . . . .

DC-DC buck converter . . . . . . . . . . . . . . .

1 Introduction to Modeling and Simulation

1.1 Importance of Simulation

1 Introduction to Modeling and Simulation

1.2 Why Simulink

1.3 SIMPOWER SYSTEM

1.3 SIMPOWER SYSTEM

1 Introduction to Modeling and Simulation

1.4 Architecture of book

2.2 Single phase half wave rectier

2.2.1 Without freewheeling diode

Figure 2.1: 1 half wave rectier with RL load

2.2 Single phase half wave rectier

Figure 2.2: Reaching simulink

add current measurement and voltage measurement blocks to untitled. Oscilloscope is

Figure 2.3: Creating a new model

Figure 2.4: Adding a block in the model

2.2 Single phase half wave rectier

Figure 2.5: Construction of a model

Figure 2.6: Voltage block

Set it to 312 V (Default is 100V)(.

Set it to zero (0) degrees.

Set it to 50Hz (Default is 60Hz)

2.2 Single phase half wave rectier

Figure 2.7: Load selection

Figure 2.8: Adjusting the oscilloscope

2.2 Single phase half wave rectier

Figure 2.9: Adjusting the oscilloscope parameters

It uses Bogacki-Shampine that is also explicit, one step Runge-Kutta. May be

It is multi step, variable order Adams-Bashforth-Moulton PECE solver.When

Multi step variable order solver based on backward dierentiation formula

2.2 Single phase half wave rectier

Figure 2.10: Getting towards the simulation parameters

Figure 2.11: Adjusting the simulation parameters

2.3 Single phase full wave center tap rectier

Figure 2.16: FFT of the rectier with free wheeling diode

2.3 Single phase full wave center tap rectier

SimPower SystemsElectrical sources AC voltage source

2.5 Three phase full wave rectier

Voltmeter (Simulink Sim Power system Measurements Voltmeter)

/

!"

4&)*5/ +)