Atlas Copco

Desiccant Air Dryers for Superior Productivity

CD+ series (25-1400 l/s, 53- 2968 cfm) / BD+ series (100-3000 l/s, 212-6360 cfm)

Desiccant_dryers_16p_brochure_20100709.indd 1

7/12/10 6:20:11 PM

Selecting the right desiccant dryer

for your application
A dry compressed air system is essential to maintain the reliability of production processes and
the quality of end products. Untreated air can cause corrosion in pipe work, premature failure of
pneumatic equipment, and product spoilage.

How does a desiccant dryer work?

Wet air passes directly through the desiccant medium which adsorbs the moisture. The desiccant medium has a finite capacity for
adsorbing moisture before it must be dried out, or regenerated. To do this, the tower containing saturated desiccant medium
is depressurized and the accumulated water is driven off. How this happens depends on the type of desiccant dryer:
Heatless dryers use only compressed air as a purge.

Blower purge dryers use a combination of air from an external blower, heat and minimal compressed air.

Why desiccant dryers?

Desiccant dryers or twin tower dryers consist of two towers filled with desiccant such as activated alumina
or silica gel. While one tower is drying compressed air, the other is being regenerated. Desiccant dryers can
achieve dewpoints of down to -40C/-40F and -70C/-100F. Three types of desiccant dryer are widely used
throughout industry: heatless, heated purge and blower purge.

Heatless dryers use a small portion of the dried compressed air for regeneration.
Heated purge dryers use a small and heated portion of the dried compressed air for regeneration.
Blower purge dryers use heated ambient air for regeneration.

The drying process

Wet compressed air flows upward through the desiccant which adsorbs the moisture, from bottom to top (1).

The regeneration process

4

Heatless desiccant dryers:

Lifecycle cost
Desiccant dryer selection should be based on the required dewpoints and the cost of energy required to operate the dryer, and not only
the initial capital cost. The energy costs are heavily dependent on the way in which the desiccant is regenerated. The illustration
compares the lifecycle cost for three types of desiccant dryers sized to dry 550 l/s / 1160 cfm.

Dry air from the outlet of the drying tower is expanded to atmospheric
pressure and sent through the saturated desiccant, forcing the
adsorbed moisture out (2) (4).
After desorption, the blow-off valve is closed and the vessel is
re-pressurized.

Dry air

2
Wet air

10 years
life cycle cost

Maintenance

Investment
Heatless

Heated Purge

Blower Purge

The heatless desiccant dryer is the most expensive to operate because of the high amount of compressed air that is consumed for
purging during the regeneration cycle. Typically, 15% of the rated flow capacity of a heatless dryer is consumed as purge air. Although
the cost of operating this type of dryer is high, the heatless type is often selected because of its simplicity and reliability.

Blower purge desiccant dryers

(with and without zero purge cooling):

The blower (5) takes ambient air and blows it over the external heater (6).
The heated air is then sent through the saturated desiccant (2), forcing
the adsorbed moisture out, from bottom to top.

Cooling

CD+ / BD+ series

Site conditions
The selection of a desiccant dryer is also determined by the site conditions in which
it has to operate. Desiccant dryers are particularly important in remote areas or hazardous
sites where the atmosphere may contain explosive gases and powders, and in
applications where the inlet air temperature is high. In such extreme environments,
heatless desiccant dryers are preferred due to their simple design.

Desiccant_dryers_16p_brochure_20100709.indd 2-3

Dry air

Zero purge: After the heating, the hot tower desiccant is cooled.
Cooling is done by sending air from the hot vessel over a cooler and
back into the hot tower, from bottom to top.
Purge: After the heating, the hot tower desiccant is cooled. Cooling
is done by expanding dry compressed air from the outlet of the
adsorbing vessel over the hot reactivated tower, from top to bottom.

6
1

2
5
3

Wet air

Switching
After regeneration, the functions of both towers are switched (3).

CD+/ BD+ series

Energy

7/12/10 6:20:42 PM

Complete protection and energy-efficiency

for your application
Dry and clean compressed air is essential for a broad range of industrial applications. Yet it must be
produced reliably, energy-efficiently and cost-effectively. Atlas Copcos desiccant dryers protect your
systems and processes. Their robust design ensures they operate with total reliability and deliver a
constant, stable dewpoint in full load conditions and even during a temporary overload.

Electronics

Food & Beverage

Exceptional reliability for critical processes

A reliable supply of dry air

Protecting your reputation and production

Compressed air entering the air net is always 100% saturated. When it cools, this moisture will condense, causing damage to your air
system and finished products. Removing moisture from compressed air with a pressure dewpoint as low as -70C/-100F, Atlas Copco
desiccant dryers eliminate system failures, production downtime and costly repairs.

Keeping your production up and running

Key features of Atlas Copcos desiccant dryers ensure maximum uptime for production processes:
Dry air is used to remove microscopic debris from the surfaces of
computer chips and boards. Moisture can play havoc with sensitive
processes and cause oxidation of micro-terminal strips, resulting
in product failure. The electronics industry needs desiccant dryers
offering a dewpoint as low as -70C/-100F , 24/7 availability and
maximum uptime.

The presence of moisture during the preparation of foods and

beverages can cause contamination of end products. Processing
machinery can also be affected by moisture, which interferes with
their operation and obstructs the free and easy movement of the
ingredient or item of food.

A constant Pressure Dewpoint (PDP) down to -70C/-100F at 100% load conditions is the result of large pipes and vessels and
efficient regeneration.
A proven, durable design for the switching valves, the most important moving components in the dryer, significantly improves the
dryer lifetime.
An advanced control and monitoring system takes continuous care of the dryer to ensure production efficiency.

Atlas Copco desiccant dryers meet or exceed the international standards for compressed air purity and are tested according to ISO 7183:2007.
Naturally, all our dryers are IP54 compliant, providing full protection of electrical components, controls and displays.

Oil & Gas

Pharmaceuticals

100% availability in a demanding environment

A tight control on quality

Driving down energy costs

Atlas Copcos desiccant dryers incorporate a range of energy-saving features that will cut your carbon footprint. A low pressure drop below
0.2 bar/2.9 psi drives down energy costs. Dewpoint sensing and control adapts the energy consumption to the real load of the dryer. An
adjustable PDP setpoint enables you to adapt the dryer to your actual needs. A zero purge variant, with closed loop cooling, provides even
further savings by consuming no compressed air at all.

Easy installation and long maintenance intervals

Desiccant_dryers_16p_brochure_20100709.indd 4-5

Strict moisture control is a key factor in the manufacture of most

drugs and medicines. Many materials used to produce
pharmaceuticals have a physical affinity for moisture, which can
cause powdered material to aggregate. Other powders that are
formed into a tablet under high pressures will adhere only when in
a dry state. Humidity can cause a tablet to crumble or the drug to
decompose and diminish in its therapeutic value. To assure
consistently high-quality drugs, the presence of dry air in the
processing area and machinery is therefore vital.

The dryers have a small footprint thanks to an innovative all-in-one design. Delivered ready for use, installation is straightforward, minimizing
costly production downtime. All internal components are easily accessible to facilitate maintenance. The use of high-grade desiccant and
durable valves extends maintenance intervals beyond the standard three years.

Assuring your peace of mind

Through continuous investment in our competent, committed and efficient service organization, Atlas Copco ensures superior customer value
by maximizing productivity. With a presence in over 160 countries, we offer professional and timely service through interaction and involvement.
Uptime is guaranteed by dedicated technicians and 24/7 availability.

CD+/ BD+ series

CD+ / BD+ series

Moisture-laden air is unacceptable for the oil and gas industry,

particularly on offshore establishments. It causes rust and pipe
scale that can clog orifices, foul transmitters and other delicate
sensing equipment, and distort instrument readings. If tools
become rusty or corroded they soon become inoperable, and
replacements are expensive. Oil & gas installations need 24/7
availability of dry compressed air at a low dewpoint.

7/12/10 6:21:25 PM

CD 25+-145+: Reliable and compact

4 Corrosion protected design

Base, heads, panels, valves and extrusion profiles are corrosion protected, increasing
dryer lifetime.

5 Filters
Pre-filter(s) protect desiccant against oil contamination, increasing desiccant lifetime.

After-filter protects network against desiccant dust, avoiding network contamination.

Can be mounted directly on the inlet and outlet of the dryer, for low pressure drop.

Easy to assemble and maintain as no extra piping and filter connections are required.

Overfilled and spring-loaded

high-performance desiccant cartridges

Pressure Dewpoint of -40C/-40F as standard (-70C/-100F as option).

Filter mat increases silencer lifetime by preventing dust exiting during regeneration.

Overfilled cartridges protect against desiccant ageing and overflow peak.

Horizontal operation possible.

6 Advanced control and monitoring system

Timer control variant cycles defined to reach PDP target even at 100% load.

Auto restart after power failure function with cycle status memory.

Full status annunciation on LEDs, display and pressure gauges.

Remote alarm and remote control.

Purge Saver contact: the dryer can freeze purge cycle in case of unload/stop signal.

All controls are protected from water and dust thanks to the IP54 cubicle.

2 Up-sized silencers with integrated

safety valves

Advanced mufflers avoid back-pressure, increase purge efficiency, offer protection

in case of clogging via the integrated safety valve, and reduce noise level during
blow-off.

7 Dewpoint Dependent Switching

(optional)
Real PDP monitoring (hygrometer).

PDP display on controller (and alarm).

The dryer will only switch to the next tower when the desiccant is
saturated (based on PDP input). During that period, the dryer
consumes no purge.

3 High-quality valve block with few moving parts

Designed to minimize pressure drop and increase reliability.

Desiccant_dryers_16p_brochure_20100709.indd 6-7

CD+/ BD+ series

CD+ / BD+ series

7/12/10 6:22:10 PM

CD 110+-1400+: Outstanding reliability

and availability

5 Filters
Pre-filter(s) protect desiccant against oil contamination,
increasing desiccant lifetime.

After-filter protects network against desiccant dust, avoiding

network contamination.

Can be mounted directly on the inlet and outlet of the dryer,

for low pressure drop.

Easy to assemble and maintain as no extra piping and filter

connections are required.

1 High-quality desiccant

Pressure dewpoint of -40C/-40F as standard (-70C/-100F as option).

Up to 30% extra desiccant overfill to deliver consistent performance even in harsh conditions
such as high temperatures and temporary overloads.

2 Stainless steel valves

Fully stainless steel high-performance butterfly valves with actuators
ensure long lifetime.

6 Advanced control and monitoring

system
Fitted inside a real IP54 cubicle for easy cabling and safety.

Monitors all parameters to ensure maximum reliability of the installation.

3 Up-sized silencers with

integrated safety valves
Advanced mufflers avoid back-pressure, increase purge
efficiency, offer protection in case of clogging via the
integrated safety valve, and reduce noise level during
blow-off.

7 Dewpoint
Dependent
Switching
Real PDP monitoring (hygrometer).

PDP display on controller

(and alarm).

The dryer will only switch to the next

tower when the desiccant is saturated
(based on PDP input). During that period,
the dryer consumes no purge.

CD+ / BD+ series

Standard frame, including forklift slots and lifting eyes for easy handling.

Flanged piping simplifies maintenance and minimizes the chance of leakage.

Pipe sizing is optimized to ensure a low pressure drop, resulting in energy savings.

Desiccant_dryers_16p_brochure_20100709.indd 8-9

8 Robust and compact design

Wide vessels ensure a low air speed and a longer contact time.
Flanges connecting vessels are integrated into the top and bottom shells, lowering the total unit height.

CD+/ BD+ series

4 Galvanized piping
with flanged connections

7/12/10 6:23:25 PM

BD 110+-3000+: Rock-solid reliability

& cost-efficiency

5 Filters
Pre-filter(s) protect desiccant against oil contamination,
increasing desiccant lifetime.

After-filter protects network against desiccant dust, avoiding

network contamination.

Can be mounted directly on the inlet and outlet of the dryer,

for low pressure drop.

Easy to assemble and maintain as no extra piping and filter

connections are required.

1 Long-life silica gel desiccant

High adsorption silica gel desiccant needs less reactivation energy than other
drying agents.

2-layer desiccant bed; a water-resistant bottom layer protects the high-performing

top layer.

Pressure dewpoint of -40C/-40F as standard (-70C/-100F as option).

Up to 30% extra desiccant overfill to deliver consistent performance even in harsh

conditions such as high temperatures and temporary overloads.

2 Stainless steel valves

Fully stainless steel high-performance butterfly valves with
actuators ensure long lifetime.

6 Advanced control and monitoring system

Fitted inside a real IP54 cubicle for easy cabling and safety.

Monitoring all parameters to ensure maximum reliability of installation.

3 Low wattage density heater

7 Dewpoint Dependent
Switching

Stainless steel design ensures long lifetime.

Nickel-plated heater pipe protects against corrosion.

Heater is installed in an insulated heater pipe for most energy-efficient setup.

Real PDP monitoring (hygrometer).

Optionally insulated vessels are available to further reduce heat losses and
increase overall efficiency (standard on the -70C/-100F variant).

PDP display on controller (and alarm).

The dryer will only switch to the next tower when the
desiccant is saturated (based on PDP input). During
that period, the dryer consumes no energy.

Desiccant_dryers_16p_brochure_20100709.indd 10-11

Flanged piping simplifies maintenance and minimizes the chance of leakage.

Pipe sizing is optimized to ensure a low pressure drop, resulting in energy savings.

Standard frame, including forklift slots and lifting eyes for easy handling.

Wide vessels ensure a low air speed and a longer contact time.

Flanges connecting vessels are integrated into the top and bottom shells,
lowering the total unit height.

CD+/ BD+ series

CD+ / BD+ series

4 Galvanized piping
with flanged connections

8 Robust and compact design

7/12/10 6:24:10 PM

Superior energy-efficiency

A step ahead in control and monitoring

A dryers energy consumption mainly goes to internal pressure drops and the regeneration process.
The key for designing desiccant dryers is therefore to keep the pressure drop as low as possible, and
to develop technologies that allow regeneration to be as efficient as possible. Atlas Copco's dryers are
designed to have a very low internal pressure drop below 0.2 bar/2.9 psi, and provide the most efficient
regeneration process.

Atlas Copco's Elektronikon control and monitoring system takes continuous care of your CD+ or BD+
desiccant dryer to ensure optimal productivity and efficiency at your site.

Low pressure drop saves energy and reduces operating costs

User-friendly interface

If a desiccant dryer experiences a high internal pressure drop, the compressor

discharge pressure must be set higher than required, which wastes energy and
increases operating costs. For example, on a 7-bar airnet, each 1 bar decrease in
pressure potentially results in a 7% reduction in energy consumption and a 25%
decrease in air leakage losses. Atlas Copco has therefore put considerable
efforts into minimizing pressure drops in its dryers. The result is that most CD+
and BD+ desiccant dryers have a pressure drop below 0.2 bar/2.9 psi.

Available in 32 languages, this graphical 3.5-inch high-definition color display

with pictograms and LED indicators for key events is easy to use. The keyboard
is durable to resist tough treatment in demanding environments.

Annual
energy
cost

1 bar/14.5 psi
Pressure drop

Comprehensive maintenance display

Efficient regeneration due to Dewpoint Dependent Switching

Valuable items of information displayed include the ServicePlan indicator and

preventive maintenance warnings.

Atlas Copcos CD+ and BD+ desiccant dryers incorporate state-of-the-art energy management control with built-in Dewpoint Dependent
Switching. This makes the dryers more efficient, leading to energy savings of up to 90%, depending on installation and usage.
The principle is simple. Although the regeneration time remains constant, the delay before switching from one tower to the other is
controlled via the PDP sensor. This is connected to a hygrometer which precisely measures the remaining humidity in the outlet compressed
air. As soon as the target PDP is reached, the dryer cycle that was on hold will resume by switching to the dry tower. Delaying cycles in this
way leads to major energy savings. This occurs when operating conditions are lower than reference, or the flow fluctuates below maximum
nominal load.

Control and monitoring

Internet-based visualization
The Elektronikon system monitors and displays key parameters such
as dewpoint, vessel pressure and inlet temperature, and includes an
energy-savings indicator. Internet-based visualization of your dryer is
possible by using a simple Ethernet connection.

Typical dryer

Atlas Copco dryer

AIRConnect

Energy consumption
Pressure drop (on average 10%)

Reduced pressure drop below 0.2 bar/2.9 psi

Regeneration (on average 90%)

Dewpoint Dependent Switching for energy savings up to 90%

Desiccant_dryers_16p_brochure_20100709.indd 12-13

CD+/ BD+ series

CD+ / BD+ series

AIRConnect is an optional advanced remote monitoring package that offers complete analysis
and accurate management. It is fully customizable to meet specific customer needs, from
simple alarm notification via email or SMS to visualization via fieldbus, LAN or internet, including
advanced reporting services.

7/12/10 6:24:42 PM

Optimize your system

Technical specifications

Scope of supply

Heatless desiccant dryers

Air circuit

Electrical components

Stainless steel butterfly valves*

Galvanised in- and outlet piping*

In- and outlet air flanges

Insulated heater pipe and connection pipe

to vessels (only on BD+)

Pre-mounted electrical cubicle

Base frame with forklift slots

Elektronikon control and monitoring system**

Lifting holes*

Connections

Framework

IP54 protected

DRYER
TYPE

Pressure dewpoint sensor and control***

PED approval

ASME approval

DIN flanges

CRN approval

ANSI-flanges

ML approval

*
Not on CD 25+-145+
** Not on CD 25+-145+ & CD 110+-300+ with Timer Control
*** Not on CD 25+-300+ with Timer Control

Additional features & options

Options

CD 25+-145+

Maximum working pressure 14.5 bar(e)/210 psig

2nd PDP read out
-70C/-100F pressure dewpoint
Pre- and after-filter package for GA oil-injected compressor*
Pre- and after-filter package for Z oil-free compressor
Pressure relief valves (not on CD+ 50 Hz versions)
Sonic nozzle
Minimum pressure valve
GSM connect
High inlet temperature variant
High ambient temperature variant
Dryer tower insulation
Optimized purge nozzle (4-5.5-8.5-10 bar(e)/58-80-123-145 psig)
Blower inlet filter
External pilot air connection for low pressure inlet
IP65 cubicle
NEMA 4 cubicle
NEMA4X cubicle
Reversed in - outlet piping
Pneumatic control
Wall mounting set
Dp switch on filters
Standard

Optional

CD 100+-300+

CD 330+-1400+

BD 100+-300+
Purge

Purge

Desiccant dryer range

52

LCC

* With electronic pressure drop monitoring

- Not available

+
+
CD
212 25 -1400
848

4240

6360

cfm

bar

psi

50 Hz: G/PN16
60 Hz: NPT/DN

1 m
0,1 ppm

0,01 m
0,01 ppm

1 m

kg

lbs

CD 25
CD 30 +
CD 35 +
CD 50 +
CD 60 +
CD 70 +
CD 80 +
CD 100 +
CD 145 +

25
30
35
50
60
70
80
100
145

90
108
126
180
216
252
288
360
522

53
64
74
106
127
148
170
212
307

0.06
0.09
0.10
0.32
0.12
0.16
0.33
0.35
0.43

0.87
1.23
1.38
4.64
1.74
2.32
4.79
5.08
6.24

"
"
"
1"
1"
1"
1"
1"
1"

DD32
DD32
DD32
DD60
DD60
DD60
DD120
DD120
DD150

PD32
PD32
PD32
PD60
PD60
PD60
PD120
PD120
PD150

DDp32
DDp32
DDp32
DDp60
DDp60
DDp60
DDp120
DDp120
DDp150

550
550
550
550
550
550
550
550
550

201
201
201
201
364
364
364
364
526

1233
1233
1478
1846
1233
1479
1846
1846
1846

21.7
21.7
21.7
21.7
21.7
21.7
21.7
21.7
21.7

7.9
7.9
7.9
7.9
14.3
14.3
14.3
14.3
20.7

48.5
48.5
58.2
72.7
48.5
58.2
72.7
72.7
72.7

50
50
60
80
100
120
160
160
240

110
110
132
176
220
265
353
353
529

CD 110 +
CD 150 +
CD 185 +
CD 250 +
CD 300 +
CD 330 +
CD 400 +
CD 550 +
CD 850 +
CD 1100 +
CD 1400 +

107
150
185
250
300
330
400
550
850
1100
1400

385
540
666
900
1080
1188
1440
1980
3060
3960
5040

227
318
392
530
636
700
848
1166
1802
2332
2968

0.12
0.16
0.20
0.14
0.19
0.10
0.10
0.10
0.10
0.10
0.11

1.74
2.32
2.90
2.03
2.76
1.45
1.45
1.45
1.45
1.45
1.60

1"
1"
1"
2"
2"
DN80
DN80
DN80
DN100
DN100
DN125

DD120
DD150
DD175
DD280
DD280
DD390
DD390
DD520
DD780
DD1050
DD1400

PD120
PD150
PD175
PD280
PD280
PD390
PD390
PD520
PD780
PD1050
PD1400

DDp120
DDp150
DDp175
DDp280
DDp280
DDp390
DDp390
DDp520
DDp780
DDp1050
DDp1400

950
1089
1089
1106
1173
1088
1088
1091
1259
1259
1428

728
848
848
960
1116
1776
1776
1884
2359
2472
2693

1695
1731
1731
1816
1854
2537
2537
2592
2655
2637
2576

37.4
42.9
42.9
43.5
46.2
43
43
43
50
50
56

28.7
33.4
33.4
37.8
43.9
70
70
74
93
97
106

66.7
68.1
68.1
71.5
73.0
99.9
99.9
102
105
104
101

340
415
445
600
650
950
1030
1310
2120
2600
3700

750
915
981
1323
1433
2109
2287
2908
4706
5772
8215

DRYER
TYPE

m/h

Blower purge desiccant dryers

Weight

in

Zero Purge

-/

Dimensions
mm

BD 300+-3000+

Filter sizes (recommended)

Pre-filters
After-filter

Inlet/outlet
connections

l/s

Mechanical approval

Voltage free contacts for remote alarm and

warning signals

Inlet flow
Pressure drop
FAD 7 bar(e)/100 psig (excluding filters)

cfm

Inlet flow
Average power
Pressure drop
Inlet/outlet
FAD 7 bar(e)/100 psig
consumption (excluding filters) connections
l/s

m/h

Purge cooling
BD 100 +
100
360
BD 150 +
150
540
BD 185 +
185
666
BD 250 +
250
900
BD 300 +
300
1080
BD 330 +
330
1188
BD 400 +
400
1440
BD 550 +
550
1980
BD 850 +
850
3060
+
BD 1100
1100
3960
BD 1400 + 1400
5040
BD 1800+ 1800
6480
BD 2200 + 2200
7920
BD 3000 + 3000
10800
Zero purge cooling
BD 330 +
330
1188
BD 400 +
400
1440
+
BD 550
550
1980
BD 850 +
850
3060
BD 1100 +
1100
3960
BD 1400 + 1400
5040
BD 1800 + 1800
6480
BD 2200 + 2200
7920
BD 3000 + 3000
10800

Filter sizes (recommended)

Pre-filters
After-filter

Dimensions
mm

Weight

in

cfm

kW

hp

bar

psi

50 Hz: G/PN16
60 Hz: NPT/DN

1 m
0,1 ppm

0,01 m
0,01 ppm

1 m

212
318
392
530
636
700
848
1166
1802
2332
2968
3816
4664
6360

3
3
5
5.5
5.5
9.3
10.2
12.0
17.1
24.2
33
39
55
69

4.1
4.1
6.8
7.4
7.4
12.6
13.8
16.2
23.1
32.7
44.6
52.7
74.3
93.2

0.20
0.20
0.20
0.20
0.20
0.12
0.12
0.12
0.12
0.12
0.10
0.16
0.22
0.18

2.90
2.90
2.90
2.90
2.90
1.74
1.74
1.74
1.74
1.74
1.45
2.32
3.19
2.61

1 1/2"
1 1/2"
1 1/2"
2"
2"
80
80
80
100
100
150
150
150
150

DD120
DD150
DD175
DD280
DD280
DD390
DD390
DD520
DD780
DD1050
DD1400
DD1800
DD2100
DD3150

PD120
PD150
PD175
PD280
PD280
PD390
PD390
PD520
PD780
PD1050
PD1400
PD1800
PD2100
PD3150

DDp120
DDp150
DDp175
DDp280
DDp280
DDp390
DDp390
DDp520
DDp780
DDp1050
DDp1400
DDp1800
DDp2100
DDp3150

1250
1300
1300
1345
1425
1764
1764
1884
2359
2472
2720
2793
2993
3350

770
870
870
955
1010
1024
1024
1024
1175
1175
2199
2199
2199
2417

1720
1770
1770
1816
1853
2558
2558
2612
2702
2681
2548
2548
2548
2893

49
51
51
53
56
69
69
74
93
97
107
110
118
132

30
34
34
38
40
40
40
40
46
46
87
87
87
95

68
70
70
71
73
101
101
103
106
106
100
100
100
114

640 1421
680 1510
710 1576
775 1721
820 1821
1190 2642
1300 2886
1620 3597
2600 5773
3040 6750
4100 9103
4700 10435
5600 12434
7600 16874

700
848
1166
1802
2332
2968
3816
4664
6360

8.6
10.7
13.2
23.4
32.4
37
45
62
79

11.6
14.4
17.8
31.6
43.7
50.0
60.8
83.7
106.7

0.12
0.12
0.12
0.12
0.12
0.10
0.16
0.22
0.18

1.74
1.74
1.74
1.74
1.74
1.45
2.32
3.19
2.61

80
80
80
100
100
150
150
150
150

DD390
DD390
DD520
DD780
DD1050
DD1400
DD1800
DD2100
DD3150

PD390
PD390
PD520
PD780
PD1050
PD1400
PD1800
PD2100
PD3150

DDp390
DDp390
DDp520
DDp780
DDp1050
DDp1400
DDp1800
DDp2100
DDp3150

1764
1764
1884
2359
2472
2720
2793
2993
3350

1024
1024
1024
1175
1175
2639
2663
2775
2923

2558
2558
2612
2702
2681
2548
2548
2548
2893

69
69
74
93
97
107
110
118
132

40
40
40
46
46
104
105
109
115

101
101
103
106
106
100
100
100
114

1420 3153
1545 3430
1910 4241
2960 6572
3490 7749
4450 9880
5050 11213
5950 13211
7950 17651

kg

lbs

Reference conditions:
Performance data per ISO 7183:2007
Compresser air inlet temperature: 35C/100F
Inlet relative humidity: 100%
Dryer inlet pressure for 11 bar variants, after inlet filtration

CD 25 -1400
+

BD 100+-3000+

25

100

* with zero purge cooling

Desiccant_dryers_16p_brochure_20100709.indd 14-15

400

2000

3000

l/s

H
L

CD+/ BD+ series

CD+ / BD+ series

BD 330+-3000+ *

7/12/10 6:24:44 PM

Driven by innovation
With more than 130 years of innovation and experience, Atlas Copco will deliver the
products and services to help maximize your companys efficiency and productivity.
As an industry leader, we are dedicated to offering high air quality at the lowest
2935 0939 41 Printed in Belgium Subject to alteration without prior notice. Never use compressed air as breathing air without prior purification in accordance with local legislation and standards.

possible cost of ownership. Through continuous innovation, we strive to safeguard

your bottom line and bring you peace of mind.
Building on interaction
As part of our long-term relationship with our customers, we have accumulated
extensive knowledge of a wide diversity of processes, needs and objectives. This
gives us the flexibility to adapt and efficiently produce customized compressed air
solutions that meet and exceed your expectations.
A committed business partner
With a presence in over 160 countries, we will deliver high-quality customer
service anywhere, anytime. Our highly skilled technicians are available 24/7
and are supported by an efficient logistics organization, ensuring fast delivery
of genuine spare parts when you need them. We are committed to providing
the best possible know-how and technology to help your company produce,
grow, and succeed. With Atlas Copco you can rest assured that your superior
productivity is our first concern!

www.atlascopco.com

Desiccant_dryers_16p_brochure_20100709.indd 16

7/12/10 6:24:50 PM