Canal Outlets

Canal Outlets
Department of Civil Engg

UET Lahore, Pakistan
Introduction
An outlet is a hydraulic structure conveying irrigation
water from a state owned distributary to privately

owned water course.
The outlets are large in number as compared to other
irrigation structures in an irrigation system and hence

their design and type has maximum bearing on the
equitable distribution of water.
Therefore proper design of outlet is of utmost

importance.
Canal Outlet
Tail cluster
Pakka nakka (Turnouts)
Essential Requirements of an outlet
An outlet should be strong and be without movable parts

to minimize tempering
Tempering by cultivators should be readily detectable
The outlet must carry its fair share of silt from parent
channel
It should be able to work with small working heads
It should be simple so that construction is easy
The total cost of installation and maintenance should be

minimum
Types of Outlets
Non-Modular Outlets
It is one in which the discharge is dependent upon the
difference of head in water course and parent channel.
Hence, a variation in either affects the discharge.
Semi-Modular (Flexible)
It is one in which the discharge depends upon the water
level in distributary only and is independent of water level
in water course.
This is achieved by producing hydraulic jump within the
flume length.
Modular (Rigid) Outlets

It is one in which the discharge is independent of the
water level in water course and parent channel.
It can be fixed for any discharge value. This is achieved
by creating a free vortex and destroying any extra head
more than allowed for in the designed discharge.
Types of Outlets
Semi-Modular
Modular
(Flexible)
(Rigid)
Non-Modular
Pipe or
Barrel Type,
with
drowned
flow at d/s
Scratchley
outlet
(a pipe type,
with a
cistern d/s)
Weir-Type
Orifice-Type
(OSM)
Harvey
Stoddard
outlet
Kennedy
Gauge
Outlet
Crumps
open
flume
outlet
Crumps
adjustable
proportion
al module
Jamrao
type open
flume
(Crumps APM)
Adjustable
orifice
semi
module
With moving parts

Without moving
parts
Gibbs module
Khanna module
Ghafoor rigid
flume module
Ref: Mahbub SI, Gulhati ND (1964),

Irrigation outlets, Paper No 264, Pakistan
Engineering Congress, Lahore.
Pipe outlet
Ref:. http://www.scribd.com/doc/113998814/6/CANAL-OU
Harveys Outlet
Gibbs Module
Characteristic of Outlets
Flexibility: It is defined as the ratio of rate of change of
discharge in outlet to the rate of change of discharge in
parent channel.
F = (dq/q)/(dQ/Q)
= (m/n)(D/H)
(H/D) is the setting of an outlet
n is exponent of discharge eq (Q=K1Dn) for canal & m is exponent of discharge eq

(q=K2Hm) for outlet. For Trap. channel with :1 side slope, n is 5/3, and for open
flume outlet m is 2/3. Therfore F =0.9 D/H. If we set the crest of outlet at 0.9D
depth below water level, the F will be 1 & the outlet will be proportional outlet.
Flexibility is the capacity of an outlet to vary its discharge

with the change in the discharge of the distributary.
If F=1
If F>1
If F<1
Proportional
Hyper-proportional
Sub-proportional
Sensitivity: It is the ratio of rate of change of discharge of
an outlet to the rate of change in the level of distributary
water surface, i.e. normal depth of channel
S = (dq/q)/(dG/D)
Here, S is the sensitivity and G is the gauge reading of a
gauge which is so set that G = 0 corresponds to the

condition of no discharge through the outlet (i.e., Q0 = 0).
Sensitivity can also be defined as the ratio of the rate of

change of discharge of an outlet to the rate of change of
depth of flow in the distributary channel.
S = nF
n = 5/3 for wide trapezoidal channel with side slope :1
Efficiency: It is equal to the ratio of the head recovered
(or the residual head after the losses in the outlet) to the
input head of the water flowing through the outlet.
Minimum Modular Head: it is the minimum head

required for the proper functioning of the outlet as per its
design.
Modular Limits: The extreme values of any parameter

at which a module or a semi module ceases to be capable
of acting as such.
Modular Range:
The range of conditions between the

modular limits within which a module or semi module works as
designed.
Coefficient of Discharge:
In order to use the outlet as

a measuring device the coefficient of discharge should
remain constant in the full modular range.
Silt Drawing Capacity: It is vital that the outlets should

draw their fair share of silt. This avoids silting or scouring
and consequently remodeling of distributary.
In a distributary system the absorportion losses are

generally taken as 10-15% and therefore the silt conducting
power of outlets should be around 110-115% as compared
to 100% of distributary to enable them to draw their
proportional share.
Adjustability: The adjustment of module may range from
complete reconstruction to the provision of some
mechanical arrangement by which readjustment can be
made at little cost. Readjustments are required in view of
the revision of areas under command and because of
change conditions in the distributary.
Immunity from Tempering:
There is tendency on the

parts of cultivators to draw more than their lawful share of
water by tampering with the outlets. Therefore the outlets
must be tamper proof.
Selection of Type of Outlet

A rigid module (Modular) or a Flexible module (Semimodular) with a constant coefficient of discharge is the
best selection if the discharge and the water levels are
constant in the distributary and necessary working head
is available.
But the problem of choice becomes quite complex when

both the discharge and levels are likely to change.
The following points may be noted;

For a temporary discharge variation a proportional
semi module is desirable to distribute both excess or
deficiency in the parent channel.
Seasonal variation in the slope require the use of
outlets of low flexibility, i.e., sub-proportional.
Selection of Type of Outlet

For channels running with full supply for a certain
period and remaining closed for certain other
periods, i.e. rotational running, it is desirable to have
hyper-proportional or high flexibility outlets in the
head reaches.
The silt drawing capacity of outlet must be 110-115%
assuming a 10-15% loss in parent channel.
In general rigid modules are desirable in the following
circumstances
Direct outlets on a branch canal subject to variation in
supply
In channels which sometimes carry extra discharge for
specific reasons like leaching.
Open Flume Outlets

This is a smooth weir with a throat constricted sufficiently
long to ensure that the controlling section remains with in
the parallel throat for all discharges up to the maximum
Since a hydraulic jump forms at the control section, the
water level of the watercourse does not affect the discharge

through this type of outlet. Hence this is a semi-modular
outlet.
This type of structure is built in masonry, but the controlling
section is generally provided with cast iron or steel bed and

check plates.
Open Flume Outlets
Open Flume Outlets

The discharge formula for the open flume outlet is given
as:
Q = C Bt H3/2
Where: Q is related to the coefficient of discharge, C, as
given in the table below; Bt is the width of the throat;

and H is the height of the full supply level of the supply
channel above the crest level of the outlet in ft.
Bt
C
0.2 ft 0.29 ft,
0.3 ft 0.39 ft
Over 0.4 ft
2.90
2.95
3.00
Crumps Open Flume Outlet Design

Data:
Outlet Discharge = q = 4 cfs
Full Supply Depth = D = 3.5 ft
Working Head = Hw = 1.0 ft
Discharge of Distributory = Q = 60 cfs
Design
1. Canal Section
According to Laceys theory, design of distributory
comes out to be
Side
Slope
1:0.5
D=5
B=38

Setting:
G= Setting of outlet
= 0.9 D
= 3.15 ft
Head above crest of outlet = 3.15 ft
Throat Width:
q= CdBtG3/2
q= 2.9BtG3/2
4=2.9Bt(3.15)3/2
Assuming Cd = 2.9
Bt= 0.2462 = 0.25 ft

Note: The value of Bt lies in between 0.2 to 0.29 ft.
(min. is 0.2ft)

Length of Crest:
Length of Crest = 2.5 G
= 2.5x3.15= 7.875=7.9 ft
Radius of Transition:
R = 2 G=6.30 ft
Setting Back:
This distance by which the wall parallel

to the distributary axis is to be set back bears the same
ratio to the width of distributary as the discharge of the
outlet to that of the distributary.
Setback/width of distributary = q/Q
Setting Back = 2.53 ft

Transition in bed:
The transition in bed is given by curve of radius= 2 G
= 2x3.15=6.3 ft
D/S Transition:
The slope of d/s glacis (1:10 to 1:15) is not defined as it
depend upon the bed level of the water course.
Minimum Modular Head:

MMH = 0.2G =0.2x3.15
= 0.63 ft < working head=1.0 ft (OK)

Flexibility:
(m=3/2, n=5/3)
F=(m/n) (D/G)
=(3/2/5/3)(1/0.9)
=1
Sensitivity:
S = nF
= 5/3 F = 5/3
Efficiency:
=100xHead recovered/Head put in
=100x(Head put in-Working head)/Head put in
=100 x (3.15-1)/3.15= 68.25%
Adjustable Proportional Module

(APM)
In this type of outlet, a cast iron base, a cast iron
roof
block and check plates on either side are used to adjust
the flow and is set in a masonry structure
This outlet works as a semi-module since it does not
depend upon the level of water in the watercourse.
The roof block is fixed to the check plates by bolts which
can be removed and depth of the outlet adjusted after
the masonry is dismantled.
This type of outlet cannot be easily tampered with and at
the same time be conveniently adjusted at a small cost.
The APM is the best type of outlet if the required working
head (MMH) is available and is the most economical in
adjustment either by raising or lowering the roof block or
crest. However, it is generally costlier than the other
types of outlets and also requires more working head.
Schematic Diagram of Outlet

Outlet discharge = q
= Cd Y Bt (Hs)1/2
Roof Block
FSL
Full supply depth in parent

channel = D
Working head = Hw
Discharge of canal = Q
Width of throat = Bt
Depth of water above crest
u/s = G
Flexibility = F
Min. Modular Head = Hm
Distance from tip of roof
block to FSL = Hs
Hs+Y = G, Hs=Y,
G = 0.6 D for proportional
Hs
V
Hm
J
Y
Tail Cluster
When the discharge of a secondary, tertiary or quaternary canal
diminishes below 150 l/s (about 5 cusecs), it is desirable to

construct structures to end the canal and distribute the water
through two or more outlets, which is called a tail cluster. Each
of these outlets is generally constructed as an open flume outlet
Thank you

Canal Outlets

Uploaded by

Copyright:

Available Formats

Canal Outlets

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Canal Outlets

Uploaded by

Copyright:

Available Formats

Canal Outlets

Department of Civil Engg

water from a state owned distributary to privately

The outlets are large in number as compared to other

irrigation structures in an irrigation system and hence

Therefore proper design of outlet is of utmost

Pakka nakka (Turnouts)

Essential Requirements of an outlet

An outlet should be strong and be without movable parts

Tempering by cultivators should be readily detectable

It should be able to work with small working heads

It should be simple so that construction is easy

The total cost of installation and maintenance should be

Modular (Rigid) Outlets

With moving parts

Ref: Mahbub SI, Gulhati ND (1964),

n is exponent of discharge eq (Q=K1Dn) for canal & m is exponent of discharge eq

Flexibility is the capacity of an outlet to vary its discharge

Here, S is the sensitivity and G is the gauge reading of a

gauge which is so set that G = 0 corresponds to the

Sensitivity can also be defined as the ratio of the rate of

Minimum Modular Head: it is the minimum head

Modular Limits: The extreme values of any parameter

The range of conditions between the

In order to use the outlet as

Silt Drawing Capacity: It is vital that the outlets should

In a distributary system the absorportion losses are

Immunity from Tempering:

There is tendency on the

Selection of Type of Outlet

But the problem of choice becomes quite complex when

The following points may be noted;

Selection of Type of Outlet

Open Flume Outlets

Since a hydraulic jump forms at the control section, the

water level of the watercourse does not affect the discharge

This type of structure is built in masonry, but the controlling

section is generally provided with cast iron or steel bed and

Open Flume Outlets

Open Flume Outlets

Where: Q is related to the coefficient of discharge, C, as

given in the table below; Bt is the width of the throat;

Crumps Open Flume Outlet Design

Crumps Open Flume Outlet Design

Bt= 0.2462 = 0.25 ft

Crumps Open Flume Outlet Design

This distance by which the wall parallel

Crumps Open Flume Outlet Design

Minimum Modular Head:

Crumps Open Flume Outlet Design

Adjustable Proportional Module

Schematic Diagram of Outlet

Full supply depth in parent

When the discharge of a secondary, tertiary or quaternary canal

diminishes below 150 l/s (about 5 cusecs), it is desirable to

You might also like