Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 38 views

    Trans Fluid Replacement

    Uploaded by

    john michel
    The document provides instructions for replacing the transmission fluid on a 2007 Chevrolet Equinox with a 3.4L V6 engine. It details removing the drain plug and old fluid, installing a new gasket and drain plug, adding new fluid, and checking the fluid level when hot.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Trans Fluid Replacement

    Uploaded by

    john michel
    38 views2 pages
    The document provides instructions for replacing the transmission fluid on a 2007 Chevrolet Equinox with a 3.4L V6 engine. It details removing the drain plug and old fluid, installing a new gasket and drain plug, adding new fluid, and checking the fluid level when hot.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for replacing the transmission fluid on a 2007 Chevrolet Equinox with a 3.4L V6 engine. It details removing the drain plug and old fluid, installing a new gasket and drain plug, adding new fluid, and checking the fluid level when hot.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    38 views2 pages

    Trans Fluid Replacement

    Uploaded by

    john michel
    The document provides instructions for replacing the transmission fluid on a 2007 Chevrolet Equinox with a 3.4L V6 engine. It details removing the drain plug and old fluid, installing a new gasket and drain plug, adding new fluid, and checking the fluid level when hot.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    2007 Chevrolet EQUINOX

    Submodel: LT | Engine Type: V6 | Liters: 3.4


    Fuel Delivery: FI | Fuel: GAS

    Transmission Fluid Replacement


    Removal Procedure

    Click to Enlarge
    1.

    Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

    2.

    Remove the drain plug and drain fluid. Allow at least 5 minutes for the fluid to drain completely.

    3.

    Remove the gasket from the drain plug and discard.

    Installation Procedure

    Click to Enlarge
    1.

    Install the new gasket on the drain plug.


    Caution!
    Refer to Component Fastener Tightening Notice in the Preface section.

    2.

    Install the drain plug.


    Tighten
    Tighten the drain plug to 39 Nm (29 lb ft).

    3.
    4.

    Make sure vehicle is level .


    Remove the fluid level indicator located behind the front transaxle mount. Refer to Transmission Fluid Level Indicator Replacement .
    Caution!
    Do not remove the 3rd gear anchor band bolt located on top of the transmission for checking fluid or adding fluid. Removing the bolt will dislocate internal components and require
    the transmission to be removed from the vehicle and disassembled for repair.
    Important
    DexronIII automatic transmission fluid is not compatible with this transaxle. If DexronIII ATF is used, transaxle failure will result. Refer to Sealers, Adhesives, and Lubricants .

    5.

    Add approximately 3.1 L (3.3 Qt) of GM T-IV fluid to the transaxle , using the fluid level indicator location.
    Important
    If the check is necessary at a low oil temperature of 30-40C (86-104F), perform check using the COLD range on the level gage. However, the fluid must be re-checked at the
    proper fluid temperature.

    6.

    Start engine and operate vehicle until transaxle fluid temperature reaches 60-70C (140-158F).

    7.

    Apply parking brake.

    8.

    Depress brake pedal and move shift lever slowly through all gear ranges from park (P) to low (L), pausing for about 3 seconds in each range. Return shift lever to park (P) range
    at idle condition.

    9.

    Pull level gauge out again and check if fluid level is within the HOT range.

    10.

    If fluid is not within the correct level, adjust accordingly:


    10.1.

    If fluid is below the HOT range, add enough to bring it up to the correct level.

    10.2.
    11.

    If fluid is above HOT range, drain excess fluid.

    Install the fluid level indicator. Refer to Transmission Fluid Level Indicator Replacement .

    You might also like