Transmission Fluid PDF

A760H AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: A...
Page 1 of 5
Last Modified: 7-19-2010 6.4 N From: 200501
Model Year: 2006 Model: GS300 Doc ID: RM0000013BU01YX
Title: A760H AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: ADJUSTMENT (2006 GS300)
ADJUSTMENT
1. BEFORE FILLING TRANSMISSION
This transmission requires Toyota Genuine ATF WS.

It is necessary to refill the transmission with the correct amount of fluid.
The vehicle must remain level while adjusting the transmission fluid level.
2. FILL TRANSMISSION PAN WITH FLUID
(a) Remove the refill plug and overflow plug.
(b) Fill the transmission through the refill hole until fluid begins to trickle
out of the overflow tube.
(c) Reinstall the overflow plug.
https://techinfo.toyota.com/t3Portal/document/rm/RM1167U/xhtml/RM0000013BU01Y... 07/31/2010
A760H AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: A... Page 2 of 5
3. FILL TRANSMISSION
(a) Fill the transmission with the correct amount of fluid as listed in the table below.
(b) Reinstall the refill plug to avoid fluid splash.
Standard capacity:
PERFORMED REPAIR FILL AMOUNT
Transmission pan and drain plug removal 1.6 liters (1.7 US qts, 1.4 Imp. qts)
Transmission valve body removal 3.7 liters (3.9 US qts, 3.25 Imp. qts)
Torque converter removal 4.7 liters (5.0 US qts, 4.1 Imp. qts)
HINT:
If you cannot add the listed amount of fluid, do the following:
(1) Install the refill plug.
(2) Allow the engine to idle with the air conditioning OFF.
(3) Move the shift lever through entire gear range to circulate fluid.
(4) Wait for 30 seconds with the engine idling.
(5) Stop the engine.
(6) Remove the refill plug and add fluid.
(7) Reinstall the refill plug.
4. CHECK FLUID TEMPERATURE
NOTICE:
The fluid temperature can be confirmed by checking the D sift indicator in the meter or by intelligent tester. It is
necessary to change to fluid temperature detection mode.
HINT:
The fluid temperature should be less than 30°C (86°F) before beginning the fluid temperature check.
(a) When using the intelligent tester:
(1) Turn the ignition switch OFF.
(2) Connect the intelligent tester to the DLC3.
(3) Turn the ignition switch ON
NOTICE:
Do not start engine yet.

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.
(4) Select the tester menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / TC/TE1.
(5) Enter the following menus: DATE LIST / AT FLUID TEMP.
(6) Check AT FLUID TEMP.
NOTICE:
If the fluid temperature is below 46°C (115°F), proceed to the next step. (Recommended ATF temperature 41°C (106°F) or
less.)
If the fluid temperature is 46°C (115°F) or more, turn the ignition switch OFF and wait until the fluid temperature drops
below 46°C (115°F).
(7) According to the display on the intelligent tester TC/TE1 "ON"
(8) Start the engine.
(b) When not using the intelligent tester (using D sift indicator):
(1) Connect terminals CG (4) and TC (13) of the DLC3 using SST.
SST: 09843-18040
(2) Start the engine.
NOTICE:
Check that electrical systems such as the air conditioning system, audio system and lighting system are off.
HINT:
Indicator lights of the meter blink to output DTCs when terminals TC and CG are connected and.
(c) Slowly move the shift lever from the P to the S position, Shift the gear from 1st to 6th and then return the shift lever return
to P position.
(d) Move the shift lever to D, and quickly move back and forth between N and D (once within 1.5 seconds) for at least 6
seconds. This will activate the fluid temperature detection mode.
NOTICE:
D sift indicator remains illuminated for 2 seconds and then off.
(e) When using the intelligent tester:
(1) Return the shift lever to P and press "OFF" on the Active Test display.
(f) When not using the intelligent tester:
(1) Return the shift lever to P and disconnect terminals 13 (TC) and 4 (CG).
(g) Allow the engine to idle until the fluid temperature reaches 41 to 46°C (106 to 115°F).
(h) The D sift indicator will come on again when the fluid temperature reaches 41°C (106°F) and will blink when it exceeds 46°C
(115°F).
D sift Indicator Indication of ATF Temperature
BELOW PROPER TEMPERATURE PROPER TEMPERATURE HIGHER THAN PROPER TEMPERATURE
Date List: [AT FLUID TEMP] Date List: [AT FLUID TEMP] Date List: [AT FLUID TEMP]
41°C (106°F) or less 41 to 46°C (106 to 115°F) 46°C (115°F) or higher
D sift indicator: D sift indicator: D sift indicator:

Turn off Turn on Blinking
NOTICE:
Perform the fluid level inspection while the D sift indicator is turn on.
5. CHECK FLUID LEVEL
NOTICE:
The fluid temperature must be between 41°C (106°F) and 46°C (115°F) to accurately check the fluid level.
(a) Remove the overflow plug with the engine idling.
(b) Check that the fluid comes out of the overflow tube.
If fluid does not come out, proceed to the "REFILL TRANSMISSION

WITH FLUID".
If fluid comes out, wait until the overflow slows to a trickle and
proceed to the "AFTER FILLING TRANSMISSION".
6. REFILL TRANSMISSION WITH FLUID
(a) Install the overflow plug.
(b) Stop the engine.
(c) Remove the refill plug.
(d) Add 0.4 liters (0.42 US qts, 0.35 Imp. qts) of fluid.
(e) Allow the engine to idle and wait for 10 seconds.
(f) Repeat the "CHECK FLUID LEVEL" procedure.
7. AFTER FILLING TRANSMISSION
(a) Install the overflow plug with a new gasket.
Torque: 20 Nm (204 kgfcm, 15ftlbf)
(b) Stop the engine.
(c) Install the refill plug with a new O-ring.
Torque: 39 Nm (400 kgfcm, 29ftlbf)

Transmission Fluid PDF

Uploaded by

Copyright:

Available Formats

Transmission Fluid PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Transmission Fluid PDF

Uploaded by

Copyright:

Available Formats

A760H AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION FLUID: A...

Last Modified: 7-19-2010 6.4 N From: 200501

Model Year: 2006 Model: GS300 Doc ID: RM0000013BU01YX

1. BEFORE FILLING TRANSMISSION

This transmission requires Toyota Genuine ATF WS.

2. FILL TRANSMISSION PAN WITH FLUID

(a) Remove the refill plug and overflow plug.

(c) Reinstall the overflow plug.

(b) Reinstall the refill plug to avoid fluid splash.

PERFORMED REPAIR FILL AMOUNT

If you cannot add the listed amount of fluid, do the following:

(1) Install the refill plug.

(4) Wait for 30 seconds with the engine idling.

(5) Stop the engine.

(6) Remove the refill plug and add fluid.

(7) Reinstall the refill plug.

4. CHECK FLUID TEMPERATURE

(a) When using the intelligent tester:

(1) Turn the ignition switch OFF.

(2) Connect the intelligent tester to the DLC3.

(3) Turn the ignition switch ON

Do not start engine yet.

(5) Enter the following menus: DATE LIST / AT FLUID TEMP.

(6) Check AT FLUID TEMP.

(7) According to the display on the intelligent tester TC/TE1 "ON"

(8) Start the engine.

(2) Start the engine.

(e) When using the intelligent tester:

(f) When not using the intelligent tester:

D sift Indicator Indication of ATF Temperature

BELOW PROPER TEMPERATURE PROPER TEMPERATURE HIGHER THAN PROPER TEMPERATURE

41°C (106°F) or less 41 to 46°C (106 to 115°F) 46°C (115°F) or higher

D sift indicator: D sift indicator: D sift indicator:

5. CHECK FLUID LEVEL

(a) Remove the overflow plug with the engine idling.

If fluid does not come out, proceed to the "REFILL TRANSMISSION

6. REFILL TRANSMISSION WITH FLUID

(a) Install the overflow plug.

(b) Stop the engine.

(c) Remove the refill plug.

(e) Allow the engine to idle and wait for 10 seconds.

(f) Repeat the "CHECK FLUID LEVEL" procedure.

7. AFTER FILLING TRANSMISSION

(a) Install the overflow plug with a new gasket.

Torque: 20 Nm (204 kgfcm, 15ftlbf)

(b) Stop the engine.

(c) Install the refill plug with a new O-ring.

Torque: 39 Nm (400 kgfcm, 29ftlbf)

You might also like

Torque: 20 Nm (204 kgfcm, 15ftlbf)

Torque: 39 Nm (400 kgfcm, 29ftlbf)