Aci350 3 06

ACI 350.
3-06
Seismic Design of Liquid-Containing

Concrete Structures and Commentary
(ACI 350.3-06)
An ACI Standard
Reported by ACI Committee 350
First Printing
November 2006
Seismic Design of Liquid-Containing Concrete Structures

and Commentary
Copyright b y the Amer ican Concrete Institute , Farmington Hills , MI. All r ights reser ved. This mater ial
may not be reproduced or copied, in whole or par t, in any printed, mechanical, electronic, film, or other
distribution and storage media, without the written consent of ACI.
The technical committees responsib le for ACI committee reports and standards str ive to avoid ambiguities,
omissions, and errors in these documents . In spite of these eff orts, the users of A CI documents occasionally find information or requirements that may be subject to more than one inter pretation or may be
incomplete or incorrect. Users who ha ve sugges tions f or the impro vement of A CI documents are
requested to contact ACI.
ACI committee documents are intended f or the use of individuals who are competent to e valuate the
significance and limitations of its content and recommendations and who will accept responsibility for the
application of the material it contains. Individuals who use this publication in any way assume all risk and
accept total responsibility for the application and use of this information.
All information in this publication is provided as is without warranty of any kind, either express or implied,
including but not limited to, the implied warranties of merchantability, fitness for a particular purpose or
non-infringement.
ACI and its members disclaim liability for damages of any kind, including any special, indirect, incidental,
or consequential damages , including without limitation, lost re venues or lost profits , which ma y result
from the use of this publication.
It is the responsibility of the user of this document to establish health and safety practices appropriate to
the specific circumstances in volved with its use . ACI does not mak e any representations with regard to
health and safety issues and the us e of this document. The user m ust determine the applicability of all
regulatory limitations before applying the document and must comply with all applicable laws and regulations, including but not limited to, United States Occupational Safety and Health Administration (OSHA)
health and safety standards.
Order information: ACI documents are available in print, by download, on CD-ROM, through electronic
subscription, or reprint and may be obtained by contacting ACI.
Most ACI standards and committee reports are gathered together in the annually revised ACI Manual of
Concrete Practice (MCP).
American Concrete Institute
38800 Country Club Drive
Farmington Hills, MI 48331
U.S.A.
Phone:
248-848-3700
Fax:
248-848-3701
www.concrete.org
ISBN 0-087031-222-7

Concrete Structures
and Commentary (ACI 350.3-06)
AN ACI STANDARD
REPORTED BY ACI COMMITTEE 350

Environmental Engineering Concrete Structures
Satish K. Sachdev
Chair
Jon B. Ardahl
Vice Chair
Walter N. Bennett
Lucian I. Bogdan
John W. Baker
Secretary
Dennis C. Kohl
Nicholas A. Legatos
Ramon E. Lucero
Andrew R. Philip
Narayan M. Prachand
Risto Protic
Patrick J. Creegan
Carl A. Gentry
Gautam Ghosh
Charles S. Hanskat
Keith W. Jacobson
Andrew R. Minogue
William C. Sherman
Ashok K. Dhingra
Robert E. Doyle
Anthony L. Felder
Dov Kaminetzky
M. Reza Kianoush
David G. Kittridge
Lawrence G. Mrazek
Javeed A. Munshi
Jerry Parnes
Lawrence M. Tabat
Lawrence J. Valentine
Steven R. Close
SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES
350.3-1

Concrete Structures and
Commentary (ACI 350.3-06)
REPORTED BY ACI COMMITTEE 350
This standard prescribes procedures for the seismic
analysis and design of liquid-containing concrete
structures. These procedures address the loading side of
seismic design and are intended to complement ACI 350-06,
Section 1.1.8 and Chapter 21.
Keywords: circular tanks; concrete ta nks; con vective component; earthquake resistance; environmental concrete structures; impulsive component;
liquid-containing structures; rect angular tanks; seismic resistance;
sloshing; storage tanks.
INTRODUCTION
The following paragraphs highlight the development of this
standard and its evolution to the present format:
From the time it embarked on the task of developing an
ACI 318-dependent code, ACI Committee 350 decided to
expand on and supplement Chapter 21, Special Provisions
for Seismic Design, to provide a set of thorough and
comprehensive procedures for theseismic analysis and design of
all types of liquid-containing environmental concrete structures.
The committees decision was influenced by the recognition
that liquid-containing structures are unique structures
whose seismic design is not adequately covered by the
leading national codes and standards. A seismic design
subcommittee was appointed with the charge to implem ent
the committees decision.
The seismic subcommittees work was guided by two
main objectives:
1. To produce a self-contained set of p rocedures that
would enable a practicing engineer to perfo rm a full seismic
analysis and design of a liquid-containing structure. This meant
that these procedures should cover both aspects of seismic
ACI Committee Reports, Guides, Standards, and Commentaries are intended
for guidance in planning, designing, executing, and inspecting construction.
This Commentary is intended for the use of individuals who are competent to
evaluate the significance and limitations of its content and recommendations
and who will accept responsibility for the application of the material it contains.
The American Concrete Institute disclaims any and all responsibility for the
stated principles. The Institute shall not be liable for any loss or damage arising
therefrom. Reference to this commentar y shall not be made in contract documents. If items found in this Commentary are desired by the Architect/Engineer
to be a part of the contract documents , they shall be restated in mandatory
language for incorporation by the Architect/Engineer.
design: the loading side (namely the determination of the

seismic loads based on the mapped maximum considered
earthquake spectral response accelerations at short periods
(Ss) and 1 second ( S1) obtained from the Seismic Ground
Motion maps [Fig. 22-1 through 22-14 of ASCE 7-05,
Chapter 22] and the geometry of the structure); and the
resistance side (the detailed design of the structure in
accordance with the provisions of ACI 350, so as to resist
those loads safely); and
2. To establish the scope of the new procedures consistent
with the overall scope of ACI 350. This required the inclusion of
all types of tanksrectangular, as well as circular; and
reinforced concrete, as well as prestressed.
(Note: While there are currently at least two national standards
that provide detailed procedures for the seismic analysis and
design of liquid-containing structures (ANSI/AWWA
1995a,b), these are limited to circular, prestressed concrete
tanks only).
As the loading side of seismic design is outside the scope of
ACI 318, Chapter 21, it was decided to maintain this practice
in ACI 350 as well. Accordingly, the basic scope, format, and
mandatory language of Chapte r 21 of ACI 318 were retained
with only enough revisions to adapt the chapter to environmental
engineering structures. Provisions similar to Section 1.1.8
of ACI 318 are included in ACI 350. This approach offers
at least two advantages:
1. It allows ACI 350 to maintain ACI 318s p ractice of
limiting its seismic design provisions to the resistance side
only; and
2. It makes it easier to update these seismic provisions so as to
keep up with the frequent changes and improvements in the
field of seismic hazard analysis and evaluation.
ACI 350.3-06 supersedes 350.3-01 a nd became effective on July 3,

2006.
Copyright 2006, American Concrete Institute.
All rights reserved including rights of reproduction and use in any
form or by any means, including the making of copies by any photo
process, or by any electronic or mechanical device, printed or written
or oral, or recording for sound or visual reproduction or for use in any
knowledge or retrieval system ordevice, unless permission in writing
is obtained from the copyright proprietors.
350.3-2
ACI STANDARD/COMMENTARY
The seismic force levels andR-factors included in this standard

provide results at strength levels, such as those included for
seismic design in the 2003 International Building Code (IBC),
particularly the applicable connection provisions of 2003 IBC,
as referenced in ASCE 7-02.When comparing these provisions
with other documents defining seismic forces at allowable
stress levels (for example, th e 1994 Uniform Building Code
[UBC] or ACI 350.3-01), the se ismic forces in this standard
should be reduced by the applicable factors to derive comparable
forces at allowable stress levels.
The user should note the fo llowing general design methods
used in this standard, which represent some of the key
differences relative to tradi tional methodologies, such as

those described in ASCE (1984):
1. Instead of assuming a rigid tank for which the accelerat ion
is equal to the ground acceleration at all locations, this
standard assumes amplification of response due to natura l
frequency of the tank;
2. This standard includes the response modification factor;
3. Rather than combining impulsive and convective modes by
algebraic sum, this standard combines these modes by
square-root-sum-of-the-squares;
4. This standard includes the ef fects of vertical accelerat ion;
and
5. This standard includes an effective mass coefficient,
applicable to the mass of the walls.
CONTENTS
CHAPTER 1GENERAL REQUIREMENTS ............................................................................ 5
1.1Scope
1.2Notation
CHAPTER 2TYPES OF LIQUID-CONTAINING STRUCTURES ......................................... 11

2.1Ground-supported structures
2.2Pedestal-mounted structures
CHAPTER 3GENERAL CRITERIA FOR ANALYSIS AND DESIGN ................................... 13

3.1Dynamic characteristics
3.2Design loads
3.3Design requirements
CHAPTER 4EARTHQUAKE DESIGN LOADS .................................................................... 15

4.1Earthquake pressures above base
4.2Application of site-specific response spectra
CHAPTER 5EARTHQUAKE LOAD DISTRIBUTION........................................................... 21

5.1General
5.2Shear transfer
5.3Dynamic force distribution above base
CHAPTER 6STRESSES....................................................................................................... 27
6.1Rectangular tanks
6.2Circular tanks
CHAPTER 7FREEBOARD ................................................................................................... 29

7.1Wave oscillation
CHAPTER 8EARTHQUAKE-INDUCED EARTH PRESSURES .......................................... 31

8.1General
8.2Limitations
8.3Alternative methods
CHAPTER 9DYNAMIC MODEL ........................................................................................... 33

9.1General
9.2Rectangular tanks (Type 1)
9.3Circular tanks (Type 2)
9.4Seismic response coefficients Ci , Cc, and Ct
9.5Site-specific seismic response coefficients Ci , Cc, and Ct
9.6Effective mass coefficient
9.7Pedestal-mounted tanks
CHAPTER 10COMMENTARY REFERENCES .................................................................... 53
350.3-3
350.3-4
APPENDIX ADESIGN METHOD...........................................................................................55

A.1General outline of design method
APPENDIX BALTERNATIVE METHOD OF ANALYSIS

BASED ON 1997 Uniform Building Code...........................................................................57
B.1Introduction
B.2Notation (not included in Section 1.2 of this standard)
B.3Loading side, general methodology
B.4Site-specific spectra (Section 1631.2(2))
B.5Resistance side
B.6Freeboard
350.3-5
CHAPTER 1GENERAL REQUIREMENTS

COMMENTARY
STANDARD
1.1Scope
R1.1Scope
This standard describes procedures for the design of

liquid-containing concrete structures subjected to seismic
loads. These procedures shall be used in accor dance
with Chapter 21 of ACI 350-06.
This standard is a companion standard to Chapter 21 of the

American Concrete Institute, Code Requirements for Environmental Engineering Concrete Structures and Commentary (ACI
350-06) (ACI Committee 350 2006).
This standard pro vides directions to the designer of liquidcontaining concrete structures for computing seismic forces
that are to be applied to the particular structure. The
designer should also consider the ef fects of seismic forces
on components outside the scope of this standard, such as
piping, equipment (for e xample, clarifier mechanisms), and
connecting walkways where v ertical or horizontal mo vements
between adjoining structures or surrounding backf ill could
adversely influence the ability of the structure to function
properly (National Science Foundation 1981). Moreover,
seismic forces applied at the interf ace of piping or w alkways
with the structure may also in troduce appreciable fle xural or
shear stresses at these connections.
1.2Notation
As
Cc, Ci ,
and Ct =
Cl , Cw =
Cs
=
d, dmax=
D
EBP
=
=
Ec
Es
=
=
Fa
Fv
Gp
R1.2Notation
cross-sectional area of base cab le, strand,

or conventional reinforcement, in.2 (mm2)
ratio of v ertical to hor izontal design acceleration
inside dimension (length or width) of a rectangular tank, perpendicular to the direction of the
ground motion being investigated, ft (m)
period-dependent seismic response coeffi cients defined in 9.4 and 9.5.
coefficients for determining the fundamental
frequency of the tank-liquid system (ref er
to Eq. (9-24) and Fig. 9.3.4(b))
period-dependent seismic coefficient
freeboard (sloshing height) measured from
the liquid surface at rest, ft (m)
inside diameter of circular tank, ft (m)
excluding base pressure (datum line just
above the base of the tank wall)
modulus of elasticity of concrete, lb/in.2 (MPa)
modulus of elasticity of cab le, wire, strand,
or conventional reinforcement, lb/in.2 (MPa)
short-period site coefficient (at 0.2 second
period) from ASCE 7-05, Table 11.4-1
long-period site coefficient (at 1.0 second
period) from ASCE 7-05, Table 11.4-2
shear modulus of elastomer ic bearing pad,
lb/in.2 (MPa)
acceleration due to g
ravity [32.17 ft/s 2
2
(9.807 m/s )]
For Cs, refer to International Building Code (IBC)

(International Code Council 2003), Section 1617.4.
EBP refers to the hydrodynamic design in which it is necess ary
to compute the o verturning of the wall with respect to the
tank floor , e xcluding base pressure (that is, e xcluding the
pressure on the floor itself). EBP h ydrodynamic design is
used to determine the need for hold-downs in nonfixed base
tanks. EBP is also used in determining the design pressure
acting on walls. (For explanation, refer to Housner [1963].)
350.3-6
COMMENTARY
STANDARD
hc
hc
hi
hi
hr
hw
HL
Hw
I
IBP
=
=
=
=
ka
Ka
Ko
L
=
=
=
Lc
Lp
mi
mw
Mb
Mc
height abo ve the base of the w all to the

center of g ravity of the con vective later al
force for the case e xcluding base pressure
(EBP), ft (m)
center of g ravity of the con vective later al
force for the case including base pressure
(IBP), ft (m)
center of g ravity of the impulsiv e later al
force for the case e xcluding base pressure
(EBP), ft (m)
height above the base of the wall to the center
of gravity of the impulsiv e lateral force for the
case including base pressure (IBP), ft (m)
height from the base of the w all to the
center of gravity of the tank roof, ft (m)
height from the base of the w all to the
center of gravity of the tank shell, ft (m)
design depth of stored liquid, ft (m)
wall height (inside dimension), ft (m)
importance factor, from Table 4.1.1(a)
including base pressure (datum line at the
base of the tank including the eff ects of the
tank bottom and supporting structure)
flexural stiffness of a unit width of a rectiline ar
tank w all, lb/ft per f oot of w all width (N/m
per meter of wall width)
spring constant of the tank w
all suppor t
system, lb/ft2 per foot of wall width (N/m per
meter of wall width)
active coefficient of lateral earth pressure
coefficient of lateral earth pressure at rest
inside dimension of a rectangular tank,
parallel to the direction of the ground motion
being investigated, ft (m)
effective length of base cab le or str and
taken as the sleeve length plus 35 times the
strand diameter, in. (mm)
length of individual elastomer ic bear ing
pads, in. (mm)
total mass per unit width of a rectangular
wall = mi + mw , lb-s 2/ft per f oot of w all
width (kg per meter of wall width)
impulsive mass of contained liquid per unit
width of a rectangular tank w all, lb-s 2/ft per
foot of wall width (kg per meter of wall width)
mass per unit width of a rectangular tank
wall, lb-s 2/ft per f oot of w all width (kg per
meter of wall width)
bending moment on the entire tank cross
section just above the base of the tank wall,
ft-lb (kN-m)
bending moment of the entire tank cross
section just above the base of the tank w all
(EBP) due to the con vective force Pc , ft-lb
(kN-m)
as defined in Section R9.2.4, ft (m)
IBP refers to the h ydrodynamic design in which it is necess ary

to in vestigate the o verturning of the entire structure with
respect to the foundation. IBP hydrodynamic design is used
to determine the design pressure acting on the tank floor and
the underlying foundation. This pressure is transferred
directly either to the subgrade or to other supporting
structural elements. IBP accounts for moment effects due to
dynamic fluid pressures on
the bottom of the tank b
y
increasing the effective vertical moment arm to the applied
forces. (For explanation, refer to Housner [1963].)
COMMENTARY
STANDARD
Mc
Mi
Mi
Mo
Mr
Mw
Ncy
Nhy
Niy
Nwy
Ny
pvy
Pc
Pcy
Peg
overturning moment at the base of the tank,

including the tank bottom and suppor ting
structure (IBP), due to the con vective force
Pc, ft-lb (kN-m)
section just above the base of tank wall (EBP)
due to the impulsive force Pi, ft-lb (kN-m)
structure (IBP), due to the impulsiv e f orce
Pi, ft-lb (kN-m)
structure (IBP), ft-lb (kN-m)
(EBP) due to the roof iner tia force Pr, ft-lb
(kN-m)
(EBP) due to the w all iner tia force Pw, ft-lb
(kN-m)
in circular tanks, hoop force at liquid level y,
due to the con vective component of the
accelerating liquid, lb per f oot of w all height
(kN/m)
in circular tanks , hydrodynamic hoop f orce
at liquid level y, due to the eff ect of vertical
acceleration, lb per foot of wall height (kN/m)
due to the impulsiv e component of the
accelerating liquid, lb per foot of wall height
(kN/m)
due to the iner tia force of the acceler ating
wall mass, lb per foot of wall height (kN/m)
in circular tanks , total eff ective hoop f orce at
liquid level y, lb per foot of wall height (kN/m)
unit equivalent hydrodynamic pressure due

to the eff ect of v ertical acceleration, at liqu id
level y, above the base of the tank (pvy = v
qhy), lb/ft2 (kPa)
total later al con vective f orce associated
with Wc , lb (kN)
lateral convective force due to Wc , per unit
height of the tank w all, occurr ing at liquid
level y, lb per foot of wall height (kN/m)
lateral force on the b uried portion of a tank
wall due to the dynamic ear th and g roundwater pressures, lb (kN)
350.3-7
pcy
piy
pwy
unit lateral dynamic convective pressure distributed

horizontally at liquid level y, lb/ft2 (kPa)
unit lateral dynamic impulsi ve pressure distributed
horizontally at liquid level y, lb/ft2 (kPa)
unit lateral inertia force due to w all dead weight,

distributed horizontally at liquid level y, lb/ft2 (kPa)
350.3-8
COMMENTARY
STANDARD
Ph
Phy
Pi
Piy
Pr
Pw
Pw
Pwy
Py
qhy
total hydrostatic force occurring on length B

of a rectangular tank or diameter D of a
circular tank, lb (kN)
lateral h ydrostatic f orce per unit height of
the tank w all, occurr ing at liquid le vel y, lb
per foot of wall height (kN/m)
total lateral impulsive force associated with
Wi , lb (kN)
lateral impulsiv e f orce due to Wi , per unit
height of the tank w all, occurr ing at liquid
level y, lb per foot of wall height (kN/m)
lateral iner tia force of the acceler ating roof
Wr , lb (kN)
lateral iner tia force of the acceler ating wall
Ww, lb (kN)
in a rectangular tank, later al iner tia f orce of
one accelerating wall (Ww ), per pendicular to
the direction of the earthquake force, lb (kN)
lateral iner tia f orce due to Ww , per unit
height of the tank w all, occurring at level y
above the tank base , lb per f oot of w all
height (kN/m)
combined hor izontal f orce (due to the
impulsive and con vective components of
the acceler ating liquid; the w alls iner tia,
and the h ydrodynamic pressure due to the
vertical acceler ation) at a height y abo ve
the tank base, lb per foot of wall height (kN/m)
unit hydrostatic pressure at liquid level y above
the tank base [qhy = L (HL y)], lb/ft2 (kPa)
For a schematic representation of Ph, refer to Fig. R5.3.1(a)

and (b)
q, qmax =
Q
=
r
R
=
=
Qhy
S0
unit shear force in circular tanks, lb/ft (kN/m)

total membrane (tangential) shear force at the
base of a circular tank, lb (kN)
in circular tanks, hydros tatic hoop force at liquid
level y (Qhy = qhy R), lb per foot of w all
height (kN/m)
inside radius of circular tank, ft (m)

response modification factor, a numerical
coefficient representing the combined effect of
the structures ductility , energy-dissipating
capacity, and structural redundancy (Rc for the
convective component of the accelerating
liquid; Ri for the impulsive component) from
Table 4.1.1(b)
effective peak ground acceleration (at T = 0)
related to the maximum considered earthquake;
expressed as a fraction of the acceleration due to
gravity g from a site-specific spectrum. ( S0 is
equivalent to a PGA having a 2% probability of
exceedance in 50 years, as given in the U.S. Geological Survey (USGS) database at website (http://
eqhazmaps.usgs.gov)
COMMENTARY
STANDARD
=
S1
SaM
Sc
ScM
SD1
SDS
Sp
Ss
tp
tw
Tc
=
=
Ti
TS
350.3-9
mapped maxim um considered ear thquake

5% damped spectr al response acceler ation;
parameter at a period of 1 second, expressed
as a fraction of the acceleration due to gravity
g, from ASCE 7-05, Fig. 22-1 through 22-14
Sa
generalized design spectral response acceleration

corresponding to a given natural period
T,
expressed as a fraction of the acceleration due to
gravity g
SD
spectral displacement, ft (m)
maximum considered earth quake spectral

response acceleration, 5% damped, at
period Ti or Tv, taken from a site-specific
acceleration response spectrum
center-to-center spacing between individual
base cable loops, in. (mm)
maximum considered earth quake spectral
response acceleration, 0.5% damped, at
period Tc , taken from a site-specific
acceleration response spectrum
design spectral response acceleration, 5%

damped, at a period of 1 second, as
defined in 9.4.1, expressed as a fraction
of the acceleration due to gravity g
design spectral response acceleration, 5%
damped, at short periods, as defined in
9.4.1, expressed as a fraction of the acceleration due to gravity g
center-to-center spacing of elastomeric
bearing pads, in. (mm)
mapped maxim um considered earthquake
5% damped spectral response acceleration
parameter at short periods, expressed as a
fraction of the acceleration due to gravity g,
from ASCE 7-05, Fig. 22-1 through 22-14
thickness of elastomeric bear ing pads ,
in. (mm)
average wall thickness, in. (mm)
natural period of the first (convective) mode
of sloshing, s
fundamental period of oscillation of the tank
(plus the impulsive component of the
contents), s
SD1/SDS
T S:
In Appendix B,
Cv
Cv
T s = --------------- = 0.40 ------Ca
2.5C a
where Ca and Cv are defined in Appendix B.
350.3-10
COMMENTARY
STANDARD
Tv
V
wp
Wc
=
=
=
We
Wi
WL
Wr
Ww
Ww
=
=
L
w
=
=
=
natural per iod of vibr ation of v ertical liquid

motion, s
effective spectr al acceler ation from an
inelastic v ertical response spectr um, as
defined b y Eq. (4-15) , that is der ived b y
scaling from an elastic hor izontal response
spectrum, e xpressed as a fr action of the
acceleration due to gravity g
total horizontal base shear, lb (kN)
width of elastomeric bearing pad, in. (mm)
equivalent w eight of the con vective comp onent of the stored liquid, lb (kN)
effective dynamic weight of the tank str ucture
(walls and roof) [We = (Ww + Wr )], lb (kN)
equivalent weight of the impulsive component
of the stored liquid, lb (kN)
total equiv alent weight of the stored liquid,
lb (kN)
equivalent w eight of the tank roof , plus
superimposed load, plus applicab le portion
of snow load considered as dead load, lb (kN)
equivalent weight of the tank w all (shell),
lb (kN)
in a rectangular tank, the equiv
alent
weight of one w all per pendicular to the
direction of the earthquake force, lb (kN)
liquid level at which the w all is being in vestigated (measured from tank base), ft (m)
angle of base cab le or strand with hor izontal,
degree
percent of critical damping
density of concrete, [150 lb/ft3 (23.56 kN/m3)
for standard-weight concrete]
density of contained liquid, lb/ft3 (kN/m3)
density of water, 62.43 lb/ft3 (9.807 kN/m3)
effective mass coefficient (ratio of equivalent
dynamic mass of the tank shell to its
actual total mass), Eq. (9-44) and (9-45)
c , i =
=
=
=
polar coordinate angle, degree

coefficient as defined in 9.2.4 and 9.3.4
membrane (hoop) stress in w all of circular
tank at liquid level y, lb/in.2 (MPa)
circular frequency of oscillation of the first
(convective) mode of sloshing, radian/s
circular frequency of the impulsiv e mode of
vibration, radian/s
coefficients as defined in Section R4.2
For , refer to Fig. R5.2.1 and R5.2.2.
350.3-11
CHAPTER 2TYPES OF LIQUID-CONTAINING STRUCTURES

STANDARD
COMMENTARY
2.1Ground-supported structures
R2.1Ground-supported structures
Structures in this category include rectangular and

circular liquid-containing concrete structures, on-grade
and below grade.
For basic conf igurations of ground-supported, liquidcontaining structures, refer to Fig. R2.1.
2.1.1Ground-supported liquid-containing str uctures

are classified according to this section on the basis of
the following characteristics:
R2.1.1The classif ications of Section 2.1.1 are based

on the wall-to-footing connection details as illustrated in
Fig. R2.1.1.
The tank floor and floor support system should be designed

for the seismic forces transmitted therein. With any one of
the tank types covered under this standard, the floor may be
a membrane-type slab, a raft foundation, or a structural slab
supported on piles. This standard, however, does not cover
the determination of seismic forces on the piles themselves.
General configuration (rectangular or circular);

Wall-base joint type (fixed, hinged, or flexible
base); and
Method of construction (reinforced or prestressed
concrete).
Type 1Rectangular tanks
Type 1.1Fixed base
Type 1.2Hinged base
The tank roof may be a free-span dome or column-supported

flat slab, or the tank may be open-topped.
Type 2Circular tanks

Type 2.1Fixed base
2.1(1)Reinforced concrete
2.1(2)Prestressed concrete
Type 2.2Hinged base
2.2(1)Reinforced concrete
2.2(2)Prestressed concrete
Type 2.3Flexible base (prestressed only)
2.3(1)Anchored
2.3(2)Unanchored, contained
2.3(3)Unanchored, uncontained
2.2Pedestal-mounted structures
Structures in this category include liquid-containing
structures mounted on cantilever-type pedestals.
Fig. R2.1Typical tank configurations (adapted from ASCE

[1984]).
350.3-12
COMMENTARY
Fig. R2.1.1Types of ground-supported, liquid-containing structures classified on the basis of their wall-to-footing connection details
(base waterstops not shown).
350.3-13
CHAPTER 3GENERAL CRITERIA FOR ANALYSIS AND DESIGN

STANDARD
COMMENTARY
3.1Dynamic characteristics
R3.1Dynamic characteristics
The dynamic char acteristics of liquid-containing

structures shall be der ived in accordance with either
Chapter 9 or a more r igorous dynamic analysis that
accounts for the interaction between the structure and
the contained liquid.
For an outline of the general steps in volved in the intera ction

between the structure and the contained liquid, refer to
Appendix A.
3.2Design loads
The loads gener ated b y the design ear thquake shall
be computed in accordance with Chapter 4.
3.3Design requirements
3.3.1The w alls, floors , and roof of liquid-containing
structures shall be designed to withstand the effects of
both the design horizontal acceleration and the design
vertical acceler ation combined with the effects of the
applicable design static loads.
3.3.2With regards to the horizontal acceleration, the
design shall take into account the effects of the transfer
of the total base shear between the wall and the footing
and betw een the wall and the roof , and the dynamic
pressure acting on the wall above the base.
3.3.3Effects of maximum horizontal and vertical
acceleration shall be combined by the square-rootsum-of-the-squares method.
350.3-14
Notes
350.3-15
CHAPTER 4EARTHQUAKE DESIGN LOADS

STANDARD
COMMENTARY
4.1Earthquake pressures above base
R4.1Earthquake pressures above base
The walls of liquid-containing structures shall be

designed for the following dynamic forces in addition to
the static pressures in accordance with Section 5.3.1:
The general equation for the total base shear normally

encountered in the earthquake-design sections of governing
building codes V = CsW is modif ied in Eq. (4-1) through
(4-4) by replacing the term W with the four effective
weights: the effective weight of the tank wall Ww and roof
Wr; the impulsi ve component of the liquid weight Wi and
the convective component Wc; and the term Cs with Ci, Cc,
or Cv as appropriate. Because the impulsi ve and convective
components are not in phase with each other, practice is to
combine them using the square-root sum-of-the-squares
method ( Eq. (4-5) ) (Ne w Zealand Standard [NZS] 1986;
ASCE 1981; ANSI/AWWA 1995a).
(a) Inertia forces Pw and Pr ;

(b) Hydrodynamic impulsive force Pi from the contained
liquid;
(c) Hydrodynamic convective force Pc from the contained
liquid;
(d) Dynamic earth pressure from saturated and
unsaturated soils against the buried portion of the wall;
and
(e) The effects of vertical acceleration.
A more detailed discussion of the impulsi ve and convective

components Wi and Wc is contained in Section R9.1.
The imposed ground motion is represented by an elastic
response spectrum that is either derived from an actual
earthquake record for the site, or is constructed by analogy
to sites with known soil and seismic characteristics. The
profile of the response spectrum is defined by Sa, which is a
function of the period of vibration and the mapped accelerations
SS and S1 as described in Section R9.4.
Factor I provides a means for the engineer to increase the
factor of safety for the cate gories of structures described in
Table 4.1.1(a). Engineering judgment may require a factor I
greater than tabulated in Table 4.1.1(a) where it is necess ary to
reduce further the potential level of damage or account for the
possibility of an earthquake greater than the design earthquake.
The response modification factors Rc and Ri reduce the elastic
response spectrum to account for the structures ductility,
energy-dissipating properties, and redundancy (ACI 350-06,
Section R21.2.1).
Explanations of the impulsive and convective pressures Pi
and Pc are contained in Section R9.1 and Housner (1963).
350.3-16
COMMENTARY
STANDARD
4.1.1Dynamic lateral forces
R4.1.1Dynamic lateral forces
The dynamic later al f orces above the base shall be

determined as
A model representation of Wi and Wc is shown in Fig. R9.1.
W w
P w = C i I ----------Ri
(4-1)
W w
P w = C i I ------------Ri
(4-1a)
W
P r = C i I -------r
Ri
(4-2)
Wi
P i = C i I ------Ri
(4-3)
Pc = Cc I
Wc
-------Rc
(4-4)
where Ci and Cc are the seismic response coefficients

determined in accordance with Sections 9.4 and
9.5; I is the impor tance factor defined in Table 4.1.1(a);
Ww and Wr are the weights of the cylindrical tank wall
(shell) and tank roof, respectively, and Ww is the
weight of one wall in a rectangular tank, perpendicular

to the direction of the ground motion being investigated;
is a factor defined in Section 1.2 and deter mined in
accordance with Section 9.6 ; Wi and Wc are the
impulsive and convective components of the stored
liquid, respectively, as defined in Section 1.2 and
determined in accordance with Sections 9.2.1 and
9.3.1; and Ri and Rc are the response modification
factors defined in Section 1.2 and determined in
accordance with Table 4.1.1(b).
Where applicable, the lateral forces due to the
dynamic earth and groundwater pressures against the
buried portion of the walls shall be computed in
accordance with the provisions of Chapter 8.
4.1.2Total base shear
The base shear due to seismic forces applied at the
bottom of the tank wall shall be determined by
V =
( Pi + Pw + Pr ) + P c + P
eg
(4-5)
Where applicab le, the later al f orces due to dynamic

earth and g roundwater pressures against the b uried
Energy Method: An ener gy method of dynamic analysis

may be used instead of the base-shear approach of Section 4.1
for sizing earthquak e cables and base pad for fle xible base
joints (Housner 1963; John A. Blume & Associates 1958;
Medearis and Young 1964; Uang and Bertero 1988; Bertero
1995; Scarlat 1997).
350.3-17
COMMENTARY
STANDARD
portion of the walls shall be included in the deter mination
of the total base shear V.
4.1.3Moments at base, general equation
The moments due to seismic forces at the base of the
tank shall be determined by Eq. (4-10) and (4-13).
Bending moment on the entire tank cross section just
above the base of the tank wall (EBP)
Mb =
Mw = Pw hw
(4-6)
Mr = Pr hr
(4-7)
Mi = Pihi
(4-8)
Mc = Pc hc
(4-9)
2
( M i + M w + M r ) + M c2
(4-10)
Overturning moment at the base of the tank, including

the tank bottom and supporting structure (IBP)
Mo =
M i = P i h i
(4-11)
Mc = Pc hc
(4-12)
2
( M i + M w + M r ) + M c2
(4-13)
Where applicable, the effect of dynamic earth and

groundwater pressures against the buried portion of
the walls shall be included in the deter mination of the
moments at the base of the tank.
4.1.4Vertical acceleration
R4.1.4Vertical acceleration
4.1.4.1 The tank shall be designed for the effects of

vertical acceleration. In the absence of a site-specific
response spectrum, the ratio b of the vertical-tohorizontal acceleration shall not be less than 2/3
The effective fluid pressure will be increased or decreased

due to the ef fects of vertical acceleration. Similar changes
in ef fective weight of the concrete structure may also
be considered.
4.1.4.2 The hydrostatic load qhy from the tank

contents, at level y above the base, shall be multiplied
by the spectral acceleration v to account for the effect
of the vertical acceleration. The resulting hydrodynamic
pressure pvy shall be computed as
IBC (2003), Section 1617.1.1, and Building Seismic Safety

Council (2000), Section 5.2.7, use afactor of 0.2SDS to
account for the effects of vertical ground acceleration in the
definition of seismic effects.
pvy = v qhy
(4-14)
350.3-18
COMMENTARY
STANDARD
where
b
v = C t I ----- 0.2S DS
Ri
(4-15)
where Ct is the seismic response coefficient deter mined

in accordance with Sections 9.4 and 9.5.
4.2Application of site-specific
response spectra
R4.2Application of site-specific
response spectra
4.2.1General
R4.2.1General
Where site-specific procedures are used, the maximum

considered earthquake spectral response acceleration
shall be taken as the lesser of the probabilistic maximum
earthquake spectral response acceleration as defined in
Section 4.2.2 and the deterministic maximum spectralresponse acceleration as defined in Section 4.2.3.
In locations with Ss 1.5 or S1 0.60 and sites with weak soil

conditions, site-specific response spectra are normally used.
4.2.2Probabilistic maximum considered earthquake
R4.2.2Probabilistic maximum considered earthquake
The probabilistic maximum considered earthquake

spectral response acceleration shall be taken as the
spectral response acceleration represented by a 5%
damped acceleration response spectrum having a 2%
probability of exceedance in a 50-year period.
For probabilistic ground motions, a 2% probability of exceedance in a 50-year period is equivalent to a recurrence
interval of approximately 2500 years.
When the a vailable site-specific response spectrum is for a
damping ratio other than 5% of critical, the period-dependent spectral acceleration SaM g iven by s uch s ite-specific
spectrum should be modified by the factor i to account for
the influence of damping on the spectral amplif ication as
follows (Newmark and Hall 1982)
For 0 seconds < (Ti or Tv) < Ts
2.706
i = -----------------------------------4.38 1.04 ln
For Ts < (Ti or Tv) < 4.0 seconds
2.302
i = -----------------------------------3.38 0.67 ln
For = 5%, i = 1.0
When the a vailable site-specific response spectrum is for a
damping ratio other than 0.5% of critical, the perioddependent spectral acceleration ScM given by that spectrum may
be modif ied b y the ratio c to account for the influence of
damping on the spectral amplification as follows
3.043
c = -----------------------------------2.73 0.45 ln
STANDARD
350.3-19
COMMENTARY
For = 0.5%, c = 1.0
For site-specif ic response spectra dra wn on a tripartite
logarithmic plot, the design spectral acceleration ScM can
also be derived by using the relationship
S 2 2
1.226S D
S cM = c -----D- ------ = c ------------------g Tc
T c2
where SD is the spectral displacement corresponding to Tc
obtained directly from the site-specif ic spectrum in the
range Tc > 1.6/Ts.
4.2.3Deterministic maximum considered earthquake
R4.2.3Deterministic maximum considered earthquake
The deterministic maximum considered earthquake

spectral response acceler ation at each period shall be
taken as 150% of the largest median 5% damped
spectral response acceleration computed at that period
for characteristic earthquakes on all known active faults
within the region. The deterministic value of the spectral
response acceler ation shall not be taken lower than
0.6Fv /T e xcept that the lower limit of the spectral
response acceleration shall not exceed 1.5Fa. The site
coefficients Fa and Fv shall be obtained from ASCE 7-05,
Tables 11.4-1 and 11.4-2, respectively.
For deterministic ground motions, the magnitude of a

characteristic earthquake on a given fault should be the
best estimate of the maximum magnitude capable for that
fault, and should not be less than the largest magnitude that
has occurred historically on the fault.
4.2.4 The maximum considered earthquake spectral

response accelerations SaM and ScM shall be determined
in accordance with Section 9.5 using the site-specific
acceleration response spectrum as defined in Section
4.2.1.
350.3-20
STANDARD
Table 4.1.1(a)Importance factor I
Table 4.1.1(b)Response modification factor R
Tank use
Factor I
III
Tanks containing hazardous materials*
1.5
II
Tanks that are intended to remain usable for

emergency purposes after an earthquake, or
tanks that are part of lifeline systems
1.25
Tanks not listed in Categories II or III
1.0
Ri
Type of structure
In some cases, for tanks containi ng hazardous materials, engineering judgment

may require a factor I > 1.5.
*Buried
On or
above
grade Buried* Rc
Anchored, flexible-base tanks
3.25
3.25
1.0
Fixed or hinged-base tanks
2.0
3.0
1.0
Unanchored, contained,
or uncontained tanks
1.5
2.0
1.0
Pedestal-mounted tanks
2.0
1.0
tank is defined as a tank whose maximum water surface at rest is at

or below ground level. For partially buried tanks, the Ri value may be linearly
interpolated between that shown for tanks on grade and for buried tanks.
R = 3.25 is the maximum R value permitted to be used for any liquid-coni
i
taining concrete structure.
Unanchored, uncontained tanks shall not be b uilt in locations where SS

0.75.
350.3-21
CHAPTER 5EARTHQUAKE LOAD DISTRIBUTION

STANDARD
COMMENTARY
5.1General
In the absence of a more rigorous analysis that takes
into account the complex vertical and horizontal
variations in hydrodynamic pressures, liquid-containing
structures shall be designed for the following dynamic
shear and pressure distributions in addition to the
static load distributions:
5.2Shear transfer
R5.2 Shear transfer (NZS 1986)

The horizontal earthquake force V generates shear forces
between the wall and footing and the wall and roof.
5.2.1Rectangular tanks
R5.2.1Rectangular tanks
The wall-to-floor, wall-to-wall, and wall-to-roof joints of

rectangular tanks shall be designed for the earthquake
shear forces on the basis of the following sheartransfer mechanism:
Typically, the distribution of forces and wall reactions in

rectangular tank walls will be similar to that shown in
Fig. R5.2.1.
Walls perpendicular to the direction of the ground

motion being investigated shall be analyzed as slabs
subjected to the horizontal pressures computed in
Section 5.3. The shears along the bottom and side
joints and the top joint in case of a roof-covered tank
shall correspond to the slab reactions; and
Walls parallel to the direction of the ground motion
being investigated shall be analyzed as shearwalls
subjected to the in-plane forces computed in
Section 5.3.
5.2.2Circular tanks
The wall-to-footing and wall-to-roof joints shall be
designed for the earthquake shear forces.
R5.2.2Circular tanks
In fixed- and hinged-base circular tanks (Types 2.1 and 2.2), the
earthquake base shear is transmitted partially by membrane
(tangential) shear and the rest by radial shear that causes vertical
bending. For a tank with a height-to-diameter ratio of 1:4 (D/HL
= 4.0 ), approximately 20% of the earthquake shear force is
transmitted by the radial base reaction to vertical bending. The
remaining 80% is transmitted by tangential shear transfer Q. To
transmit this tangential shear Q, a distributed shear force q is
required at the wall/footing interface, where
Q
q = ----- sin
r
The distribution is illustrated in Fig. R5.2.2.
The maximum tangential shear occurs at a point on the tank
wall oriented 90 degrees to the design earthquake direction
being evaluated and is given by
350.3-22
COMMENTARY
STANDARD
Q
0.8V
q max = ----- = ----------r
r
The radial shear is created by the flexural response of the wall
near the base, and is therefore proportional to the hydrodynamic
forces shown in Fig. R5.2.1. The radial shear attains its
maximum value at points on the tank wall oriented zero
and 180 degrees to the ground motion and should be
determined using cylindrical shell theory and the tank
dimensions. The design of the wall-footing interface
should take the radial shear into account.
In general, the wall-footing interface should have reinforcement
designed to transmit these shears through the joint.
Alternatively, the wall may be located in a preformed slot in
the ring beam footing.
In anchored, flexible-base, circular tanks (Type 2.3(1)) it is
assumed that the entire base shear is transmitted by membrane
(tangential) shear with only insignificant vertical bending.
Q = 1.0V
Q
V
q max = ----- = ----r
r
In tank Types 2.3(2) and 2.3(3) it is assumed that the base
shear is transmitted b y friction only. If friction between the
wall base and the footing, or between the wall base and the
bearing pads, is insufficient to resist the earthquake shear,
some form of mechanical restraint such as dowels, galvanized
steel cables, or preformed slots may be required.
Failure to provide a means for shear transfer around the
circumference may result in sliding of the wall.
When using preformed slots, vertical bending moments
induced in the wall by shear should be considered.
The roof-to-wall joint is subject to earthquake shear from
the horizontal acceleration of the roof. Where dowels are
provided to transfer this shear , the distribution will be the
same as shown in Fig. R5.2.2 with maximum shear given by
0.8P
q max = -------------r
r
where Pr is the force from the horizontal acceleration of
the roof.
For tanks with roof overhangs, the concrete lip can be
designed to withstand the earthquake force. Because the
roof is free to slide on top of the wall, the shear transfer will
take place over that portion of the circumference where the
lip overhang comes into contact with the wall. Typically, the
distribution of forces and wall reactions in circular tanks
STANDARD
350.3-23
COMMENTARY
will be similar to that shown in Fig. R5.2.1, but reacting on
only half of the circumference. The maximum reaction
force will be given by
2.0P
q max = -------------r
r
Fig. R5.2.1Hydrodynamic pressure distribution in tank

walls (adapted from Housner [1963] and NZS [1986]).
Fig. R5.2.2Membrane shear transfer at the base of circular

tanks (adapted from NZS [1986]).
350.3-24
COMMENTARY
STANDARD
5.3Dynamic force distribution above base
R5.3Dynamic force distribution above base
R5.3.1Rectangular tanks
Walls perpendicular to the ground motion being investigated and in the leading half of the tank shall be
loaded perpendicular to their plane (dimension B ) by
the walls own inertia force P w , one-half the impulsive
force Pi , and one-half the convective force Pc .
The v ertical distrib ution, per foot of w all height, of the

dynamic forces acting perpendicular to the plane of the wall
may be assumed as sho wn belo w (adapted from NZS
[1986], Section 2.2.9.5), and Fig. R5.3.1(b).
Walls perpendicular to the ground motion being

investigated and in the trailing half of the tank shall be
loaded perpendicular to their plane (dimension B) by
the walls own inertia force Pw , one-half the impulsive
force Pi; one-half the convective force Pc, and the
dynamic ear th and groundwater pressure against the
buried portion of the wall.
Walls parallel to the direction of the ground motion
being investigated shall be loaded in their plane
(dimension L) by: (a) the walls own in-plane inertia
force Pw and the in-plane forces corresponding to the
edge reactions from the abutting wall(s).
Superimposed on these lateral unbalanced forces
shall be the lateral hydrodynamic force resulting from
the hydrodynamic pressure due to the effect of vertical
acceleration pvy acting on each wall.
5.3.2Combining dynamic f orces for rectangular
tanks
The hydrodynamic force at any given height y from the
base shall be determined by
Py =
2 + ( p B )2
( P iy + P wy ) + P cy
vy
(5-1)
Where applicable, the effect of the dynamic earth and

groundwater pressures against the buried portion of
the walls shall be included.
Fig. R5.3.1(a)Vertical force distribution: rectangular tanks.

The horizontal distribution of the dynamic pressures across
the wall width B is
P wy
p wy = -------B
P cy
p cy = ------B
P iy
p iy = -----B
pvy = v qhy
The dynamic force on the leading half of the tank will be

additive to the hydrostatic force on the wall, and the dynamic
force on the trailing half of the tank will reduce the effects of
the hydroVWDWLF force on the wall.
350.3-25
COMMENTARY
Fig. R5.3.1(b)Distribution of hydrostatic and hydrodynamic pressures and inertia forces on the wall of a rectangular liquidcontaining structure (adapted from Haroun [1984]). (For circular tanks, the vertical distribution of the impulsive and convective
forces is identical to that shown above for rectangular tanks, while the horizontal distribution varies along the tank circumference
as shown in Fig. R5.2.1.)
350.3-26
STANDARD
COMMENTARY
5.3.3Circular tanks
R5.3.3Circular tanks
The cylindrical walls of circular tanks shall be loaded by

the walls own inertia force distributed uniformly around
the entire circumference; one-half the impulsive f orce
Pi applied symmetr ically about = 0 degrees and acting
outward on one half of the w alls circumference, and onehalf Pi symmetr ically about = 180 degrees and acting
inward on the opposite half of the walls circumference;
one-half the convective force Pc acting on one-half of the
walls circumference symmetr ically about = 0 degrees
and one-half Pc symmetrically about = 180 degrees
and acting inward on the opposite half of the walls
circumference; and the dynamic earth and groundwater
pressure against the trailing half of the b uried portion of
the wall.
The vertical distribution, per foot of wall height, of the

dynamic forces acting on one half of the wall may be
assumed as shown below and in Fig. R5.3.3 and Fig. R5.2.1.
Superimposed on these lateral unbalanced forces shall

be the axisymmetric later al h ydrodynamic f orce
resulting from the hydrodynamic pressure pvy acting
on the tank wall.
Fig. R5.3.3Vertical force distribution: circular tanks.

The horizontal distribution of the dynamic pressure across
the tank diameter D may be assumed as follows
P wy
p wy = -------r
16P cy
p cy = ------------- cos
9r
2P
p iy = ---------iy- cos
r
pvy = v qhy
350.3-27
CHAPTER 6STRESSES
COMMENTARY
STANDARD
R6General
In calculating the v ertical bending moments in the w alls of
rectangular and circular tank s, the boundary conditions at
the wall-to-base and w all-to-roof joints should be properly
accounted for . T ypical earthquak e force distrib utions in
walls of rectangular and circular tanks are presented in
R5.3.1 and R5.3.3, respectively.
6.1Rectangular tanks
The vertical and horizontal bending stresses and
shear stresses in the wall and at the wall base due to
lateral earthquake forces shall be computed on the
basis of slab action (Sections 5.2 and 5.3) using pressure
distribution consistent with the provisions of Section 5.3.1.
6.2Circular tanks
R6.2Circular tanks
The vertical bending stresses and shear stresses in the

wall and at the wall base due to lateral earthquake
forces shall be computed on the basis of shell action
using an acceptable pressure distribution.
For free-base circular tanks (T ype 2.3), the terms in Eq. (6-1 )
are defined as
2P
Niy = piy r = ---------iy- for (at = 0)
Hydrodynamic membrane (hoop) forces in the cylindrical

wall corresponding to any liquid le vel y above the tank
base shall be determined by
Ny =
2 + N2
( N iy + N wy ) + N cy
hy
16P cy
Ncy = pcy r = -------------for (at = 0)
9
(6-1)
P wy
Nwy = pwy r = -------
and hoop stress

Ny
(6-2)
y = ----------12t w
N
[ y = ------y in the SI system]
tw
where tw = w all thickness at the le vel being in vestigated
(liquid level y).
Nhy = v Qhy
where
Qhy = qhy r
For fixed- or hinged-base circular tanks (Types 2.1 and 2.2),
the terms in Eq. (6-1) should be modified to account for the
effects of base restraint. Similarly , the terms in Eq. (6-1)
should be modified to account for the restraint of rigid wallto-roof joints.
350.3-28
Notes
350.3-29
CHAPTER 7FREEBOARD
COMMENTARY
STANDARD
7.1Wave oscillation
R7.1Wave oscillation
Provisions shall be made to accommodate the maxim um

wave oscillation dmax generated by earthquake
acceleration.
The horizontal earthquake acceleration causes the contained

fluid to slosh with vertical displacement of the fluid surface.
The maximum vertical displacement dmax to be

accommodated shall be calculated from the following
expressions:
Rectangular tanks
L
d max = ---C c I
2
(7-1)
Circular tanks
The amount of freeboard required in design to accommodate

this sloshing will v ary. Wh ere o vertopping is tolerable, no
freeboard provision is necessary. Where loss of liquid should
be prevented (for example, tanks for the storage of toxic liquids)
or where o vertopping may result in scouring of the foundation
materials or cause damage to pi pes, roof, or both, then one or
more of the following measures should be undertaken:
D
d max = ---- C c I
2
(7-2)
where Cc is the seismic response coefficient as

computed in Section 9.4.
Provide a freeboard allowance;

Design the roof structure to resist the resulting uplift
pressures; and/or
Provide an overflow spillway.
Where site-specific response spectra are used, the maximum

vertical displacement dmax may be calculated from the
following expressions:
Rectangular tanks
( 0.667S D ) 2 2
L
L
d max = --- ( C c I ) = --- I ( c ) ------------------------ ----- 2
2
Tc
g
Circular tanks
( 0.667S D ) 2 2
D
D
d max = ---- ( C c I ) = ---- I ( c ) ------------------------ ----- 2
2
Tc
g
where Cc is defined in Section 9.5; and ScM (as in the equation
for Cc), c , and SD are as defined in Section R4.2.2.
350.3-30
Notes
350.3-31
CHAPTER 8EARTHQUAKE-INDUCED EARTH PRESSURES

STANDARD
COMMENTARY
8.1General
R8.1General
Dynamic earth pressures shall be taken into account

when computing the base shear of a partially or fully
buried liquid-containing structure and when designing
the walls.
The lateral forces due to the dynamic earth and groundwater

pressures are combined algebraically with the impulsi
ve
forces on the tank as in Eq. (4-5).
The effects of groundwater table, if present, shall be

included in the calculation of these pressures.
The coefficient of lateral earth pressure at rest Ko shall
be used in estimating the earth pressures unless it is
demonstrated by calculation that the structure deflects
sufficiently to lower the coefficient to some value
between Ko and the active coefficient of later al ear th
pressure Ka.
In a pseudostatic analysis, the resultant of the seismic
component of the ear th pressure shall be assumed to
act at a point 0.6 of the earth height above the base ,
and when part or all of the structure is below the water
table, the resultant of the incremental increase in
groundwater pressure shall be assumed to act at a
point 1/3 of the water depth above the base.
8.2Limitations
In a buried tank, the dynamic backfill forces shall not
be relied upon to reduce the dynamic effects of the
stored liquid or viceversa.
8.3Alternative methods
The provisions of this chapter shall be per mitted to be
superseded by recommendations of the project geotechnical engineer that are approved by the building
official having jurisdiction.
350.3-32
Notes
350.3-33
CHAPTER 9DYNAMIC MODEL

STANDARD
COMMENTARY
9.1General
R9.1General
The dynamic characteristics of ground-supported liquidcontaining structures subjected to earthquake acceleration

shall be computed in accordance with Sections 9.2, 9.3
and 9.5.
The lateral seismic pressures and forces determined in

accordance with this Standard are based on v ertical tank
walls and v ertical w all elements, and the pressures and
forces may need to be modified for sloping surfaces.
The dynamic char acteristics of pedestal-mounted

liquid-containing str uctures shall be computed in
accordance with Section 9.7.
The following commentary is adapted from Housner (1963):

The design procedures described in Chapter 4 recognize
that the seismic analysis of liquid-containing structures
subjected to a horizontal acceleration should include the
inertia forces generated b y the acceleration of the structure
itself; and the hydrodynamic forces generated by the horizontal
acceleration of the contained liquid.
According to Housner (1963), the pressures associated with
these forces can be separated into impulsive and convective
parts. The impulsive pressures are not impulses in the usual
sense b ut are associated with inertia forces produced b
y
accelerations of the w alls of the container and are directly
proportional to these accelerations. The con vective press ures
are those produced b y the osci llations of the fluid and are
therefore the consequences of the impulsive pressures.
Figure R9.1 (on p. 43) sho ws an equivalent dynamic model for
calculating the resultant seismic forces acting on a groundbased fluid container with rigid w alls. This model has
been accepted by the profession since the early 1960s. In
this model, Wi represents the resultant ef fect of the impuls ive
seismic pressures on the tank w alls. Wc represents the
resultant of the sloshing (convective) fluid pressures.
In the model, Wi is rigidly f astened to the tank w alls at a
height hi above the tank bottom, which corresponds to the
location of the resultant impulsi ve force Pi. Wi moves with
the tank w alls as the y respon d to the ground shaking (the
fluid is assumed to be incompressible and the fluid displacements small). The impulsi ve pressures are generated b y the
seismic accelerations of the tank w alls so that the force Pi is
evenly divided into a pressure force on the w all accelerating into
the fluid, and a suction force on the w all accelerating away from
the fluid. During an earthquak e, the force Pi changes direction
several times per second, corresponding to the change in direction
of the base acceleration; the overturning moment generated by Pi
is thus frequently ineffective in tending to overturn the tank.
Wc is the equi valent weight of the oscillating fluid that
produces the con vective pre ssures on the tank w alls with
resultant force Pc, which acts at a height of hc above the tank
bottom. In the model, Wc is fastened to the tank walls by springs
350.3-34
COMMENTARY
STANDARD
that produce a period of vibration corresponding to the period of

fluid sloshing. The sloshing pr essures on the tank w alls result
from the fluid motion associated with the w ave oscillation. The
period of oscillation of the sloshing depends on the ratio of fluid
depth to tank diameter , and is usually se veral seconds. The
overturning moment e xerted by Pc (Fig. R9.1 [on p. 43])
acts for a sufficient time to tend to uplift the tank wall if there is
insufficient restraining weight. The forces Pi and Pc act
independently and simultaneous ly on the tank. The force Pi
(and its associated pressures) primarily act to stress the tank
wall, whereas Pc acts primarily to uplift the tank w all.
The vertical vibrations of the ground are also transmitted to the
fluid, thus producing pressures that act on the tank w alls. They
act to increase or decrease the hoop stresses.
The pressures and forces on a cylindrical tank are similar to, but
not the same as, those acting on a rectangular tank.
The rapid fluctuations of the force Pi mean that the bending
moments and stresses in the wall of a rectangular tank also vary
rapidly (the effect is not like a constant force acting on the wall).
The duration of the fluctuations is 10 to 15 seconds for earthquakes of magnitude 6.5 to 7.5.
The force Pc fluctuates sinusoidally with a period of vibration
that depends on the dimensions of the tank, and can be se veral
seconds or longer. The duration of sloshing can be 20 to
40 seconds for earthquakes of magnitude 6.5 to 7.5. Note that
the damping of the sloshing w ater is small: approximately
0.5 to 1% of critical damping. The sloshing increases and
decreases the fluid pressure on the w all. Normally, this is
smaller than the impulsi ve effect, but if there is not enough
dead load, the tank will tend to uplift.
R9.2Rectangular tanks (Type 1)
9.2Rectangular tanks (Type 1)

9.2.1Equivalent weights of accelerating liquid
(Fig. 9.2.1 [on p. 44])
L
tanh 0.866 ----- H L
Wi
-------- = ----------------------------------------------WL
L
0.866 -------
H L
(9-1)
W
H
L
-------c- = 0.264 ------- tanh 3.16 ------L-
L
H L
WL
(9-2)
9.2.2Height to center s of gra vity EBP ( Fig. 9.2.2

[on p. 45])
L
For tanks with ------- < 1.333
HL
All equations in Section 9.2 e xcept Eq. (9-9), (9-10), and (9-11)
were originally developed by Housner (1963), and subsequently
used by other authors (Housner 1956; NZS 1986; Haroun 1984;
ASCE 1981; V eletsos and Shi vakumar 1997; ANSI/A WWA
1995a,b; Haroun and Ellaithy 1985).
Equations (9-9), (9-10), and (9-11) were adapted from NZS
(1986).
COMMENTARY
STANDARD
h
L
------i- = 0.5 0.09375 -------
HL
HL
350.3-35
(9-3)
L
For tanks with ------ 1.333
HL
h
------i- = 0.375
HL
(9-4)
H
cosh 3.16 ------L- 1
h
L
------c- = 1 -------------------------------------------------------------------HL
H
H
3.16 ------L- sinh 3.16 ------L-
L
L
(9-5)
For all tanks
9.2.3Heights to center of gravity IBP ( Fig. 9.2.3

[on p. 46])
L
HL
hi
------ = 0.45
HL
(9-6)
L
HL
L
0.866 -------
H L
hi
1
------- = --------------------------------------------------- --HL
8
L
2 tanh 0.866 ------ H L
(9-7)
For all tanks

H
cosh 3.16 ------L- 2.01
hc
L
-------- = 1 -------------------------------------------------------------------HL
H
H
3.16 ------L- sinh 3.16 ------L-
L
L
(9-8)
9.2.4Dynamic properties
R9.2.4Dynamic properties
The str uctural stiffness k shall be computed on the

basis of correct boundary conditions.
i =
k
----m
m = mw + mi
The follo wing equations are pr ovided as e xamples for the

special case of a wall of uniform thickness. (Note that mass
is equal to weight divided by the acceleration due to gravity.)
(9-9)
(9-10)
t w c
m w = H w ----- ---12 g
350.3-36
COMMENTARY
STANDARD
2
T i = ------ = 2 m
----i
k
(9-11)
t w c
[ m w = H w ------- ---- in the SI system]
3
10 g
c = ------L
(9-12)
W L
m i = --------i --- H L ----L-

W L 2 g
( hw mw + hi mi )
h = -----------------------------------( mw + mi )
where
H
3.16g tanh 3.16 ------L-
L
2
2
T c = ------ = ------ L

c
(9-13)
(9-14)
where hw = 0.5Hw, and hi is obtained from Eq. (9-3) and (9-4),

and Fig. 9.2.2 (on p. 44).
For w alls of nonuniform thickness, special analysis is
required to determine mw, mi, and h.
For fixed-base, free-top cantilever walls, such as in open-top
tanks, fle xural stiffness for a unit width of w all k may be
approximated using the following equation
2
from Fig. 9.2.4
-----
E t 3
k = ------c ---w-
48 h
Ec
t 3
[ k = ----------------3 ---w- in the SI system]
4 10 h
Flexural stiffness formulas may be developed for other wall
support conditions. Such spring constants will generally fall
within the low period range (less than about 0.3 seconds) for
tanks of normal proportions.
As an alternati ve to computing the natural period of vibration,
particularly for end conditions other than cantile ver, it is
reasonable to assume the wall rigid. In such a case, Eq. (9-32)
may be conserv atively used to calculate the impulsi ve
forces regardless of the actual boundary conditions of the
structure or structural components being analyzed.
R9.3Circular tanks (Type 2)
9.3Circular tanks (Type 2)

9.3.1Equivalent weights of accelerating liquid
(Fig. 9.3.1 [on p. 48])
D
tanh 0.866 ----- H L
Wi
-------- = ----------------------------------------------WL
D
0.866 -------
H L
(9-15)
W
H
D
-------c- = 0.230 ------- tanh 3.68 ------L-
D
H L
WL
(9-16)
All equations in Section 9.3, e xcept Eq. (9-23) through

(9-28), were originally de veloped by Housner (1963), and
subsequently used by other authors (Housner 1956; NZS 1986;
Haroun 1984; ASCE 1981; V eletsos and Shi vakumar 1997;
ANSI/AWWA 1995a,b; Haroun and Ellaithy 1985).
Equations (9-23) through (9-28) were adapted from NZS
(1986).
350.3-37
COMMENTARY
STANDARD
9.3.2Heights to center s of gra vity (EBP [ Fig. 9.3.2;
on p. 49])
D
HL
h
D
------i- = 0.5 0.09375 -------
H L
HL
(9-17)
D
HL
h
------i- = 0.375
HL
(9-18)
H
cosh 3.68 ------L- 1
h
D
------c- = 1 -------------------------------------------------------------------HL
H
H
3.68 ------L- sinh 3.68 ------L-
D
D
(9-19)
For all tanks
9.3.3Heights to center of gra vity (IBP [ Fig. 9.3.3;

on p. 50])
D
HL
h
------i- = 0.45
HL
(9-20)
D
For tanks with ------- 0.75
HL
D
0.866 -------
H L
hi
------- = --------------------------------------------------- 1
--HL
8
D
2 tanh 0.866 -------
H L
(9-21)
H
cosh 3.68 ------L- 2.01
D
hc
-------- = 1 -------------------------------------------------------------------HL
H
H
3.68 ------L- sinh 3.68 ------L-
D
D
(9-22)
9.3.4Dynamic properties
R9.3.4Dynamic properties
Ti: For tank Types 2.1 and 2.2:
Equations (9-23) and (9-24) are adapted from ASCE (1981)

and Veletsos and Shivakumar (1997).
12
g
i = C l ------- E c ----HL
c
(9-23)
Equations (9-26) and (9-27) are adapted from ANSI/AWWA

(1995a,b).
350.3-38
STANDARD
COMMENTARY
3
1
g
[ i = C l ------- 10 E c ----- in the SI system]
HL
c
Equations (9-13) , (9-14), (9-29), and (9-30) are adapt ed

from Housner (1963).
tw
C l = C w 10 -------12r
(9-24)
[Cw from Fig. 9.3.4(a); on p. 51]

tw
[ C l = C w -------- in the SI system]
10r
2
T i = -----i
(9-25)
For tank Type 2.3

8 ( W w + W r + W i )
------------------------------------------------gDk a
Ti =
(9-26)
but shall not exceed 1.25 seconds.

A s E s cos 2 2G p w p L p
k a = 144 ------------------------------ + -------------------------
Lc Sc
tp Sp
(9-27)
k a = 10
3 A s E s cos 2G p w p L p
------------------------------- + ------------------------- [in the SI system]
Lc Sc
tp Sp
Tc :
c = -------D
(9-28)
where
=
H
3.68g tanh 3.68 ------L-
D
2
2
T c = ------ = ------ D

c
(9-29)
(9-30)
2
[ ------ from Fig. 9.3.4(b); on p. 52]

Tv: For circular tanks
Tv
L DHL2
-----------------------24gt w E c
(9-31)
350.3-39
COMMENTARY
STANDARD
2
L DH L
[ T v = 2 --------------------- in the SI system]
2gt w E c
Y
9.4Seismic response coefficients Ci , Cc ,

and Ct
R9.4Seismic response coefficients Ci, Cc,

and Ct
In practice, Designations Ci, Cc, and Ct define the profile of
the design response spectrum at periods
Ti, Tc, and Tv,
respectively. A plot of the seismic response coef ficient Ci is
shown in the design response spectrum in Fig. R9.4.1,
which is adapted from IBC (2003).
Fig. R9.4.1Design response spectrum.
9.4.1 Ci shall be determined as follows:

For T i TS
Ci = SDS
(9-32)
For Ti > TS
S D1
C i = --------Ti
S DS
(9-33)
where
TS =
D1
--------
S DS
(9-34)
SDS = the design spectr al response acceler ation at

short periods
2
SDS = --- SsFa
3
(9-35)
SD1 = the design spectral response acceleration at a

1 second period
R9.4.1 The mapped spectral response accelerations Ss

and S1 for any location can also be obtained from the late st
database of the U.S. Geological Surv ey (USGS), at http://
eqhazmaps.usgs.gov, using the specif ic zip code or latitude
and longitude that identify the location.
In regions other than those sho wn in the maps in publicat ions
by IBC (2003), Building Se ismic Safety Council (1997,
2000), and ASCE (2005), SS and S1 may be replaced b y
the maximum considered earthquak e spectral response
accelerations from 5% damped response spectra repres enting
earthquakes with a 2% probability of e xceedance in a
50-year period, equi valent to a recurrence interv al of
approximately 2500 years.
350.3-40
COMMENTARY
STANDARD
2
SD1 = --- S1Fv
3
(9-36)
SS and S1 are the mapped spectr al response accelerations at short periods (Ss) and 1 second ( S1), respectively, and shall be obtained from the seismic g round
motion maps in Fig. 22-1 through 22-14 of ASCE 7-0 5,
Chapter 22; and Fa and Fv are the site coefficients and
shall be obtained from T
able 11.4-1 and 11.4-2,
respectively, of ASCE 7-05, in conjunction with
Table 20.3-1, Site Classification, of ASCE 7-05.
9.4.2 Cc shall be determined as follows:
For Tc 1.6/Ts seconds
1.5S D1
C c = -------------------Tc
1.5S DS
(9-37)
R9.4.2 Factor 1.5 represents the approximate ratio of the

spectral amplifications based on 0.5% damping to those
based on 5% damping.
0.4SDS in Eq. (9-38) is an
approximation of the effective peak ground acceleration S0
(at T = 0) reduced by a factor of 2/3.
For Tc > 1.6/Ts seconds

0.4S DS
2.4S DS
C c = 6 ------------------= ------------------2
2
Tc
Tc
(9-38)
9.4.3 Ct shall be determined as follows:

For circular tanks
For Tv TS
Ct = SDS
(9-39)
For Tv >TS
Ct =
S D1
-------Tv
(9-40)
For rectangular tanks, Ct = 0.4SDS.
R9.4.3 The period of vibration of v ertical liquid motion Tv

for a circular tank (upright c ylinder) is deri ved from the
axisymmetric pulsating (breathing) of the cylindrical wall
due to the h ydrodynamic pressures resulting from the v ertical,
piston-like pounding of the st ored liquid b y the v ertically
accelerating ground.
This mode of vibration is relevant only to circular tanks, and
does not apply to rectangular tanks. While the deri vation of
Tv for circular tanks has been th e subject of se veral technic al
papers, the committee is not a ware of an y work devoted to
the deri vation of this parameter for rectangular tanks.
Therefore, for rectangular tanks, Ct is taken independent of
the period of vibration.
9.5Site-specific seismic response

coefficients Ci , Cc , and Ct
R9.5Site-specific seismic response

coefficients Ci, Cc, and Ct
When site-specific procedures are used, the maximum

considered ear thquake spectr al response acceler ations
SaM and ScM shall be obtained from the site-specific
acceleration spectrum as follows:
For damping ratios other than 5% of critical, refer toSection R4.2.
For per iods less than or equal to

TS , SaM shall be
taken as the spectral acceleration obtained from the sitespecific spectra at a per iod of 0.2 seconds, except that it
shall not be tak en less than 90% of the peak spectr al
acceleration at an y per iod larger than 0.2 seco nds. For
If the site-specif ic response spectrum does not e xtend into,

or is not well defined in the Tc range, coefficient Cc may be
calculated using the equation
2
--- S 0 4S
3
C c = 6 --------- = --------02
2
Tc
Tc
350.3-41
COMMENTARY
STANDARD
periods g reater than TS , SaM shall be tak en as the
spectral response acceler ation corresponding to Ti or
Tv , as applicab le. When a 5% damped, site-specific
vertical response spectr um is a vailable, SaM shall be
determined from that spectr um when used to deter mine
Ct ; and
ScM shall be tak en as 150% of the spectr al response
acceleration corresponding to Tc, except that when a
0.5% damped, site-specific horizontal response spectrum
is a vailable, ScM shall be equal to the spectr
al
response acceleration from that spectr um corresponding
to period Tc.
where S0 is the effective site-specific peak ground accelerat ion

(at T = 0) expressed as a fraction of the acceleration due to
gravity g.
The use of site-specific response spectra represents one specific
case of an accepted alterna tive method of analysis permitt ed
in Section 21.2.1.7 of ACI 350-06. Therefore, the 80%
lower limit imposed in 9.5 should be considered the same as
the limit imposed in Section 21.2.1.7 of ACI 350-06.
The seismic response coefficients Ci, Cc, and Ct shall

be deter mined from Eq. (9-41), (9-42), and (9-43),
respectively.
For all periods, Ti
2
C i = --- S aM
3
(9-41)
2
C c = --- S cM
3
(9-42)
2
Ct = --- S aM
3
(9-43)
For all periods, Tc
For all periods, Tv
The values of Ci , Cc, and Ct used for design shall not

be less than 80% of the corresponding v
alues as
determined in accordance with Section 9.4.
9.6Effective mass coefficient
R9.6Effective mass coefficient
The coefficient represents the ratio of the equi valent (or

generalized) dynamic mass of the tank shell to its actual
total mass. Equation (9-44) and (9-45) are adapted from
ASCE (1981).
L 2
L
= 0.0151 ------- 0.1908 ------- + 1.021
H
H
L
1.0 (9-44)
For additional information related to the ef

fective mass
coefficient , consult Veletsos and Shivakumar (1997).
9.6.2Circular tanks
D 2
D
= 0.0151 ------- 0.1908 ------- + 1.021
H
H
L
L
1.0 (9-45)
350.3-42
STANDARD
COMMENTARY
9.7Pedestal-mounted tanks
R9.7Pedestal-mounted tanks
The equivalent weights, Wi and Wc , and heights to the

centers of gravity, hi, hc , hi, and hc of a mounted tank,
shall be computed using the corresponding
Eq. (9-2)
and (9-3) for rectangular and circular tanks, respectively.
Housner (1963), Haroun and

Ellaithy (1985), and A CI
Committee 371 (1998) pro vide additional guidelines on the
dynamic analysis of pedestal-mounted tanks.
The dynamic proper ties, including per iods of vibration

and later al coefficients , shall be per mitted to be
determined on the basis of gener
ally acceptab le
methods of dynamic analysis.
STANDARD
Fig. R9.1Dynamic model of liquid-containing tank rigidly

ASCE [1984]).
350.3-43
COMMENTARY
supported on the gr ound (adapted fr om Housner [1963] and
350.3-44
COMMENTARY
STANDARD
IMPULSIVE AND CONVECTIVE MASS FACTORS vs. L/HL RATIO
Fig. 9.2.1Factors Wi /WL and Wc /WL versus ratio L/HL for rectangular tanks.
L-
tanh 0.866 ----- H L
Wi
-------- = ----------------------------------------------WL
L
0.866 -------
H L
(9-1)
HL
W
L
-------c- = 0.264 -------- tanh 3.16 --------
L
H
WL
L
(9-2)
350.3-45
COMMENTARY
STANDARD
IMPULSIVE AND CONVECTIVE HEIGHT FACTORS vs. L/HL RATIO
Fig. 9.2.2Factors hi /HL and hc /HL versus ratio L/HL for rectangular tanks (EBP).
hi /HL:
L
HL
h
L
------i- = 0.5 0.09375 -------
HL
HL
(9-3)
L
HL
h
------i- = 0.375
HL
(9-4)
hc /HL:
For all tanks
H
cosh 3.16 ------L- 1
L
hc
------- = 1 -------------------------------------------------------------------------HL
H
H
3.16 ------L- sinh 3.16 ------L-
L
L
(9-5)
350.3-46
COMMENTARY
STANDARD
IMPULSIVE AND CONVECTIVE HEIGHT FACTORS vs. L/HL RATIO
Fig. 9.2.3Factors hi/HL and hc/HL versus ratio L/HL for rectangular tanks (IBP).
hi /HL :
L
HL
h
------i- = 0.45
HL
(9-6)
L
HL
L
0.866 -------
H L
hi
1
------- = -------------------------------------------------------- --HL
8
L
2 tanh 0.866 ------ H L
(9-7)
hc /HL :
For all tanks
H
cosh 3.16 ------L- 2.01
L
hc
-------- = 1 -------------------------------------------------------------------HL
H
H
3.16 ------L- sinh 3.16 ------L-
L
L
(9-8)
350.3-47
COMMENTARY
STANDARD
FACTOR (2/)
Fig. 9.2.4Factor 2/ for rectangular tanks.
"For results in the SI system, multiply the factors on the vertical axis by 1.811."
c = ------L
=
H
3.16g tanh 3.16 ------L-
L
2
2
T c = ------ = ------ L

c
(9-12)
(9-13)
(9-14)
350.3-48
COMMENTARY
STANDARD
IMPULSIVE AND CONVECTIVE MASS FACTORS vs. D/HL RATIO
Fig. 9.3.1Factors Wi / WL and Wc/WL versus ratio D/HL for circular tanks.
D
tanh 0.866 -------
H
W
L
--------i = ----------------------------------------------WL
D
0.866 -------
H L
(9-15)
W
H
D
-------c- = 0.230 ------- tanh 3.68 ------L-
D
H L
WL
(9-16)
350.3-49
COMMENTARY
STANDARD
IMPULSIVE AND CONVECTIVE HEIGHT FACTORS vs. D/HL RATIO
Fig. 9.3.2Factors hi / HL and hc /HL versus ratio D/HL for circular tanks (EBP).
hi /HL:
D
HL
h
D
------i- = 0.5 0.09375 -------
H L
HL
(9-17)
D
HL
h
------i- = 0.375
HL
(9-18)
hc /HL:
For all tanks
H
cosh 3.68 ------L- 1
D
hc
------- = 1 -------------------------------------------------------------------HL
H
H
3.68 ------L- sinh 3.68 ------L-
D
D
(9-19)
350.3-50
STANDARD
COMMENTARY
IMPULSIVE AND CONVECTIVE HEIGHT FACTORS vs. D/HL RATIO
Fig. 9.3.3Factors hi /HL and hc /HL versus ratio D/HL for circular tanks (IBP).
hi /HL:
D
HL
h
------i- = 0.45
HL
(9-20)
D
HL
D
0.866 -------
H L
hi
------- = --------------------------------------------------- 1
--HL
8
D
2 tanh 0.866 -------
H L
(9-21)
hc /HL:
For all tanks
H
cosh 3.68 ------L- 2.01
D
hc
-------- = 1 -------------------------------------------------------------------HL
H
H
3.68 ------L- sinh 3.68 ------L-
D
D
(9-22)
350.3-51
COMMENTARY
STANDARD
COEFFICIENT C W
Fig. 9.3.4(a)Coefficient Cw for circular tanks.

For D /HL > 0.667
C w = 9.375 10
5
H 2
H
H 3
H 4
2 H
+ 0.2039 ------L- 0.1034 ------L- 0.1253 ------L- + 0.1267 ------L- 3.186 10 ------L-
D
D
D
D
D
350.3-52
COMMENTARY
STANDARD
FACTOR (2/)
Fig. 9.3.4(b)Factor 2/ for circular tanks.
"For results in the SI system, multiply the factors on the vertical axis by 1.811."
c = -------D
H
3.68g tanh 3.68 ------L-
D
2
2
T c = ------ = ------ D

c
(9-28)
(9-29)
(9-30)
350.3-53
COMMENTARY
CHAPTER 10COMMENTARY
REFERENCES
ACI Committee 350, 2006, Code Requirements for Environmental Engineering Concrete Structures and C ommentary
(350-06), American Concrete Institute, Farmington Hills,
Mich., 484 pp.
ACI Committee 371, 1998, Guide for the Analysis,
Design, and Construction of Concrete-Pedestal W
ater
Towers (A CI 371R-98) (Reappro ved 2003), American
Concrete Institute, Farmington Hills, Mich., 36 pp.
American Society of Civil Engineers (ASCE), 1981, Guidelines for the Seismic Design of Oil and Gas Pipeline Systems,
Committee on Gas and Liquid Fuel Lifelines of the T echnical
Council on Lifeline Earthquake Engineering, Section 7.
American Society of Ci vil Engineering (ASCE), 1984,
Fluid/Structure Interaction During Seismic Excitation,
Report by Committee on Seismic Analysis.
American Society of Ci vil Engineers (ASCE), 2005,
Minimum Design Loads for Buildings and Other Struct ures,
ASCE 7-05, Reston, Va.
ANSI/AWWA, 1995a, AWWA Standard for W ire- and
Strand-Wound, Circular , Prestressed Concrete W
ater
Tanks, ANSI/AWWA D110-95.
ANSI/AWWA, 1995b, AWWA Standard for Circular
Prestressed Concrete W ater T anks with Circumferential
Tendons, ANSI/AWWA D115-95.
Bertero, V. V., 1995, Ener gy Based Design Approach,
Performance-Based Seismic Engineering of Buildings
,
SEAOC, Apr., pp. D-1 to D-12.
Building Seismic Safety C ouncil, 1997, NEHRP Recommended Provisions for Seismic Re gulations for New Buildings
and Other StructuresPart 1: Provisions (FEMA 302) and Part
2: Commentary (FEMA 303), Washington, D.C.
Building Seismic Safety C ouncil, 2000, NEHRP Recommended Provisions for Seismic Re gulations for New Buildings
and Other StructuresP art 1: Pro visions (FEMA 368)
and Part 2: Commentary (FEMA 369), Washington, D.C.
Haroun, M. A., 1984, Stress Analysis of Rectangular
Walls Under Seismically Induced Hydrodynamic Loads,
Bulletin of the Seismolo gical Society of America , V. 74,
No. 3, June, pp. 1031-1041.
Haroun, M. A., and Ellaith y, H. M., 1985, Seismically
Induced Fluid Forces on Elevated Tanks, Journal of Technical
Topics in Civil Engineering , ASCE, V. III, No. 1, Dec.,

pp. 1-15.
Housner, G. W ., 1956, Limit Design of Structures to
Resist Earthquak es, Proceedings, W orld Conference on
Earthquake Engineering, University of California, Berkeley,
pp. 5-1 to 5-13.
Housner, G. W ., 1963, Dynamic Pressure on Fluid
Containers, Technical Information (TID) Document 7024,
Chapter 6 and Appendix F, U.S. Atomic Energy Commission.
International Code Council, 2003, International Building
Code, 656 pp.
International Conference of Building Of ficials (ICBO),
1997, Uniform Building Code, V. 2, Whittier, Calif.
John A. Blume & Associates, 1958, Report of T esting
Program on Earthquak e Cable Detail for the Preload
Company, Inc., July.
Medearis, K., and Y oung, D. H., 1964, Ener gy Absorption
of Structures Under Cyclic Loading, Journal of the
Structural Division, ASCE, V. 90, ST1, Feb., pp. 61-89.
National Science F oundation, 1981, Earthquak e Design
Criteria for Water Supply & Wastewater Systems, National
Science Foundation Report NSF/CE52-81079, Sept.
Newmark, N. M., and Hall, W. J., 1982, Earthquak e
Spectra and Design, Earthquake Engineering Resear ch
Institute Monograph.
New Zealand Standard (NZS), 1986, Code of Practice
for Concrete Structures for the Storage of Liquids, NZS
3106, 77 pp.
Scarlat, A. S., 1997, Design of Soft StoriesA Simplifi ed
Energy Approach, Earthquake Spectra, V. 1 3, N o. 2 , M ay,
pp. 305-315.
Uang, C. M., and Bertero, V. V., 1988, Use of Energy as
a Design Criterion in Earthquak e-Resistant Design, EERC
Report No. UCB/EERC-88, Nov.
Veletsos, S. A., and Shivakumar, P., 1997, Dynamic
Response of Tanks Containing Liquids or Solids, Computer
Analysis and Design of Earthquake-Resistant Structures ,
Earthquake Engineering Series V. 3, D. E. Beskos and S.
A. Anagnostopoulos, eds., Computational Mechanics
Publications, Billerica, Mass., 936 pp.
350.3-54
Notes
350.3-55
COMMENTARY
APPENDIX ADESIGN METHOD

A.1General outline of design method
In the absence of a more rigorous method of analysis, the general procedures out lined below may be used to apply the pro visions of
Chapters 1 through 9.
Basic seismic design parameters:
1. Establish the design depth of the stored liquid HL , the wall height Hw, and the tank length or diameter, L or D, respectively;
2. From the applicable seismic ground motion map of ASCE 7-05, Chapter 22, obtain the mapped maximum considered earthquake spectral response accelerations at short periods and at 1 second (SS and S1, respectively). After selecting the site classification from ASCE 7-05, T able 20.3-1, obtain coef ficients Fa and Fv using ASCE 7-05, T ables 11.4-1 and 11.4-2, and
calculate SDS and SD1 using Eq. (9-35) and (9-36);
3. Select an importance factor I from Table 4.1.1(a);
4. Select the factors Ri and Rc from Table 4.1.1(b) for the type of structure being investigated;
Tank dynamic properties:
5. Calculate the equivalent weight of the tank wall (shell) Ww, roof Wr, and the stored liquid WL. Also, compute the effective
mass coefficient ;
6. Calculate the effective weight of the impulsive component of the stored liquid Wi, and the convective component Wc using
Fig. 9.2.1 for rectangular tanks or Fig. 9.3.1 for circular tanks;
7. Calculate the heights hw, hr, hi, and hc (EBP) and hi and h c (IBP) to the center of gravity of the tank wall, roof, impulsive
component, and convective component, respectively (Fig. 9.2.2, 9.2.3, 9.3.2, and 9.3.3, or Sections 9.2 and 9.3);
8. Calculate the combined natural frequenc y of vibration i of the containment structure and the impulsive component of the
stored liquid (Eq. (9-9) for rectangular tanks or Eq. (9-23) for circular tank Types 2.1 and 2.2). The impulsive mode will generally fall
into the rigid range of the response spectra (that is, the constant spectral acceleration region of the design response spectrum in
Fig. R9.4.1) for common sizes of concrete tanks. Thus, if the maximum value of Ci is used (SDS), calculation of the natural
frequency and natural period is not required;
9. Calculate the frequenc y of the vibration c of the convective component of the stored liquid ( Eq. (9-12) for rectangular
tanks or Eq. (9-28) for circular);
10. Using the frequency values determined in Steps 8 and 9, calculate the corresponding natural periods of vibration Ti and
Tc.(Eq. (9-11) and (9-14) for rectangular tanks, or Eq. (9-25), (9-26), and (9-30) for circular tanks);
11. Based on the natural periods determined in Step 10 and the design spectral response acceleration values derived in Step 2,
calcu-late the corresponding seismic response coefficients Ci and Cc (Eq. (9-32), (9-33), (9-37), and (9-38)). Note: Where
a site-specific response spectrum is constructed in accordance with Section 4.2.1, Ci and Cc are determined in accordance
with Sections 9.5 and R9.5;
Freeboard:
12. Where required, calculate the maximum vertical displacement of liquid surf ace (w ave height) in accordance with Chapter 7 .
Adjust the wall height if required to meet freeboard requirements;
350.3-56
COMMENTARY
Base shear and overturning moments:
13. Compute the dynamic lateral forces (Eq. (4-1) to (4-4)) and total base shear V (Eq. (4-5));
14. Calculate the bending and overturning moments (Eq. (4-10) and (4-13));
Vertical acceleration:
15. Compute the vertical amplification factor Ct in accordance with Section 9.4.3. For circular tanks, first calculate the natural
period of vibration of vertical liquid motion Tv (Eq. (9-31));
16. Calculate the hydrodynamic pressure pvy (Eq. (4-14));
Pressure distribution:
17. Compute the vertical distribution of the force components in accordance with Chapter 5;
Stresses:
18. In rectangular tanks, calculate the stresses in the wall due to the impulsive and convective pressures, depending on the
structural system considered (Section 6.1) and the stresses associated with the increase in effective fluid density due to the
vertical acceleration. In circular tanks, calculate the hoop stresses due to the impulsive and convective pressures and due to the
vertical acceleration (Section 6.2); and
19. Calculate the overall bending stresses due to the overturning moments (from Step 14). Downward pressures on the
neoprene bearing pads of free base circular tanks caused by overturning moments should be co nsidered. If uplift develops on
the heel side, then anchor cables must be provided.
350.3-57
COMMENTARY
APPENDIX BALTERNATIVE METHOD OF ANALYSIS BASED ON

1997 Uniform Building Code
B.1Introduction
B1.1Scope
The purpose of this appendix is to permit the user to adapt the pro visions of ACI 350.3 to the seismic pro visions of the 1997
edition of the Uniform Building Code (UBC) (ICBO 1997). The differences between the 1997 UBC and the 2003 IBC seismic
provisions as used in this Standard are primarily due to differences in the definition of design ground motions and the
construction of the corresponding design response spectra as explained below.
NOTE: All section, table, figure and equation references are to 1997 UBC except as otherwise indicated.
B1.2Design ground motions
This appendix presents an outline of the methodolog y to be followed when computing the loadin g side of seismic analysis in
accordance with 1997 UBC. In this case, the design ground motions are those with a 10% probability of exceedance in
50 years.
B.2Notation (not included in Section 1.2 of this standard)

Ca
= seismic coefficient, as set forth in Table 16-Q
Cv
= seismic coefficient, as set forth in Table 16-R
DL
=
E
=
LL
=
SA, SB, SC,
SD, SE, SF =
dead load
earthquake load as defined in Section 1630.1
live load
soil profile types as set forth in Table 16-J
Ts
= near-source factor used in the determination of Ca in Seismic Zone 4 related to the proximity of the structure to
known faults with magnitudes and slip rates as set forth in Tables 16-S and 16-U
= near-source factor used in the determination of Cv in Seismic Zone 4 related to the proximity of the structure to
known faults with magnitudes and slip rates as set forth in Tables 16-T and 16-U
= 0.40Cv /Ca
= seismic zone factors as given in Table 16-I
Na
Nv
B.3Loading side, general methodology

1. Select the seismic zone (1 through 4) where the site is located, using the seismic zone map (Fig. 16-2);
2. Using the seismic zone determined in Step 1, find the zone factor Z from Table 16-I;
3. Consulting paragraph 1636.2 and Table 16-J, select the soil profile type designation SA through SF that best represents the
soil at the site;
4. Using the zone factor Z and the soil profile designation from Steps 2 and 3, find the seismic coefficient Ca from Table 16-Q
and seismic coefficient Cv from Table 16-R;
5. If the structure is in Seismic Zone 4, select a Seismic So urce Type A, B, or C from Table 16-U, and near-source factors Na
and Nv from Tables 16-S and 16-T, respectively;
350.3-58
COMMENTARY
C
Cv
6. Compute T s = ------------- = 0.40 -----v- ;
2.5C a
Ca
7. Using the values of Ca, Cv, and Ts, construct a design response spectrum as in Fig. 16-3 and B.1;
Fig. B.1Modified UBC 1997 design response spectrum (ICBO 1997).

8. Seismic response coefficients Ci and Cc
8.1 Ci (impulsive component): Compute period of vibration Ti in accordance with Eq. (9-11) of this Standard for rectangular
tanks, and Eq. (9-25) or (9-26) for circular.
(Note 1: Section 1634.1.4 specif ies the method for determining th e fundamental period b y referencing 1630.2.2. F or liquidretaining structures, however, the methods in Chapter 9 of this standard should be used.)
Compute seismic response coefficient Ci corresponding to T, using the above design response spectrum as follows
(Note 2: Section 1629.8, Selection of Lateral-force Procedures, allows three options for computing lateral forces, depending
on the type of structure being investigated: simplified static, static, or dynamic. For liquid-containing structures, this standard
uses the static procedures in accordance with 1629.8.3, modified as indicated in this standard.)
For all seismic zones:
For Ti Ts
Ci = 2.5Ca
(B-1)
Ci = Cv /Ti
(B-2)
Ci 1.6ZNv
(B-3)
For Ti > Ts
In addition, for Seismic Zone 4
8.2 Cc (convective component): Compute period of vibration Tc using Eq. (9-14) of this Standard for rectangular tanks,
and (9-30) for circular tanks.
1.5C
Cc = -------------v 3.75Ca
Tc
(B-4)
350.3-59
COMMENTARY
C
C c = 6 -----a-2
Tc
(B-5)
9. Base shears V
Compute Ww, Wr , and WL;

Compute Wi and Wc using the equations in Sections 9.2 and 9.3 of this Standard;
Select coefficient Ri and Rc from Table 4.1.1(b) of this Standard.
Select an importance factor I from Table 4.1.1(a) of this Standard.
Compute the component parts of the total lateral force, Pw, Pr , Pi , and Pc in accordance with Section 4.1.1 of this Standard
as follows.
For all seismic zones

Ci I
- W w
P w = ------Ri
(B-6)
Ci I
P r = ------- W r
Ri
(B-7)
Ci I
P i = ------- W i
Ri
(B-8)
Cc I
P c = -------W
Rc c
(B-9)
Equation (B-8) and (B-9) take the following form depending on the period Ti and Tc.
For Ti Ts
2.5C a I
P i = ----------------W
i
Ri
[1997 UBC Eq. (30-5)]
For Ti > Ts
Cv I
0.56C a IW i
P i = ----------W
Ri Ti i
[1997 UBC Eq. (30-4) and (34-2)]

6C a I
1.5 ( 2.5C a )I
P c = ----------- W ---------------------------- Wc
2 c
Rc
Rc Tc
(B-10)
1.5C v I
P c = ---------------W
Rc Tc c
(B-11)
350.3-60
COMMENTARY
In addition, for Seismic Zone 4
1.6ZN v I
P i -------------------- Wi
Ri
[1997 UBC Eq. (34-3)]
10. Total base shear VThe total base shear due to Pw , Pr , Pi , and Pc may be computed b y combining these lateral loads
using the square root of the sum of the squares method as in Section 4.1.2 of this Standard
V =
( Pw + Pr + Pi ) + Pc
11. Vertical load distributionThe vertical distribution of the lateral seismic forces may be assumed as shown in Section 5 of
this Standard;
12. Vertical component of ground motionCompute the natural period of vibration of the vertical liquid motion Tv in accordance with
Section 9.3.4 of this Standard.
Compute seismic response coefficient Ct as follows:
For all seismic zones:
For circular tanks
For Tv Ts
Ct = Ca
(B-12)
C
C t = ------v
Tv
(B-13)
Ct = Ca
(B-14)
Ct 1.6ZNv
(B-15)
b
v = C t I----Ri
(B-16)
For Tv > Ts
For rectangular tanks, for all periods Tv
In addition, for Seismic Zone 4:

For rectangular and circular tanks
Compute the spectral acceleration v as follows
13. Overturning momentsCompute overturning moments for the lateral loads described above using the procedures of
Section 4.1.3 of this Standard. Combine th e computed moments using the square root of the sum of the squares method as in
the same section.
B.4Site-specific spectra (Section 1631.2(2))

When a site-specific design response spectrum is available, the coefficients Ci and Ct are replaced by the actual spectral values
corresponding to Ti and Tv, respectively, from the 5% damped site-specific spectrum, and Cc is replaced by the actual spectral
350.3-61
COMMENTARY
value corresponding to Tc from the 0.5% damped site-specific spectrum.
If the site-specific response spectrum does not extend into or is not well defined in the Tc range, coefficient Cc may be calculated using
Eq. (B-4), with Cv representing the effective site-specific peak ground acceleration expressed as a fraction of the acceleration
due to gravity g.
B.5Resistance side
1. The resistance side of the seismic desi gn, including load combinations and streng th reduction factors, may be computed in
accordance with the applicable provisions of 1997 UBC (ICBO 1997) or ACI 350-06, Chapter 9; and
2. Where the approved standard defines acceptance criteria in terms of allowable stresses (as opposed to strengths), the design
seismic forces obtained from this appendix shall be reduced b y a factor of 1.4 for use with allowable stresses, and allo wable
stress increases used in the appro ved standard are permitted. When such a standard is used, the following load combinations
are permitted to be used for design instead of the ASCE 7-05 load factor combinations (Haroun and Ellaithy 1985).
DL + LL + E/1.4
B.6Freeboard
L or D
d max = Cc I -----------------
2
(B-17)
As A CI begins its second centur y of adv ancing co ncrete kno wledge, its or iginal char tered pur pose
remains to pro vide a comr adeship in finding the be st w ays to do concrete w ork of all kinds and in
spreading knowledge. In keeping with this purpose, ACI supports the following activities:
Technical committees that produce consensus reports, guides, specifications, and codes.
Spring and fall conventions to facilitate the work of its committees.
Educational seminars that disseminate reliable information on concrete.
Certification programs for personnel employed within the concrete industry.
Student programs such as scholarships, internships, and competitions.
Sponsoring and co-sponsoring international conferences and symposia.
Formal coordination with several international concrete related societies.
Periodicals; the ACI Structural Journal and the ACI Materials Journal, and Concrete International.
As a member of A CI, y ou join thousands of pr actitioners and prof essionals w orldwide who share a
commitment to maintain the highest industr y st andards f or concrete technolog y, constr uction, and
practices. In addition, A CI chapters provide opportunities for interaction of professionals and practitioners
at a local level.
Benefits of membership include a subscr iption to Concrete Inter national and to an A CI Jour nal. A CI
members receive discounts of up to 40% on all A CI products and ser vices, including documents, seminars
and convention registration fees.
American Concrete Institute

38800 Country Club Drive
Farmington Hills, MI 48331
U.S.A
Phone:
248-848-3700
Fax:
248-848-3701
www.concrete.org
Seismic Design of Liquid-Containing Concrete Structures

and Commentary
The AMERICAN CONCRETE INSTITUTE

was founded in 1904 as a nonprofit mem bership organization dedicated to pub lic
service and representing the user interest in the field of concrete. ACI gathers and
distributes inf ormation on the impro
vement of design, constr
uction and
maintenance of concrete products and structures. The work of ACI is conducted by
individual A CI members and through v olunteer committees composed of both
members and non-members.
The committees, as w ell as A CI as a whole , operate under a consensus f ormat,
which assures all participants the right to have their views considered. Committee
activities include the development of building codes and specifications; analysis of
research and de velopment results; presentation of constr
uction and repair
techniques; and education.
Individuals interested in the activities of ACI are encouraged to become a member.
There are no educational or emplo yment requirements . A CIs membership is
composed of engineers , architects , scientists , contr actors, educators , and
representatives from a variety of companies and organizations.
Members are encouraged to par ticipate in committee activities that relate to their
specific areas of interest. For more information, contact ACI.
www.concrete.org

Aci350 3 06

Uploaded by

Document Informationclick to expand document informationSeismic Design of Liquid-Containing Concrete Structures and Comentary (ACI 350.3-06)

Document Informationclick to expand document information

Copyright:

Available Formats

Aci350 3 06

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aci350 3 06

Uploaded by

Copyright:

Available Formats

ACI 350.

Seismic Design of Liquid-Containing

Reported by ACI Committee 350

Seismic Design of Liquid-Containing Concrete Structures

Seismic Design of Liquid-Containing

REPORTED BY ACI COMMITTEE 350

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

Seismic Design of Liquid-Containing

design: the loading side (namely the determination of the

ACI 350.3-06 supersedes 350.3-01 a nd became effective on July 3,

The seismic force levels andR-factors included in this standard

differences relative to tradi tional methodologies, such as

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

CHAPTER 2TYPES OF LIQUID-CONTAINING STRUCTURES ......................................... 11

CHAPTER 3GENERAL CRITERIA FOR ANALYSIS AND DESIGN ................................... 13

CHAPTER 4EARTHQUAKE DESIGN LOADS .................................................................... 15

CHAPTER 5EARTHQUAKE LOAD DISTRIBUTION........................................................... 21

CHAPTER 7FREEBOARD ................................................................................................... 29

CHAPTER 8EARTHQUAKE-INDUCED EARTH PRESSURES .......................................... 31

CHAPTER 9DYNAMIC MODEL ........................................................................................... 33

CHAPTER 10COMMENTARY REFERENCES .................................................................... 53

APPENDIX ADESIGN METHOD...........................................................................................55

APPENDIX BALTERNATIVE METHOD OF ANALYSIS

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

CHAPTER 1GENERAL REQUIREMENTS

This standard describes procedures for the design of

This standard is a companion standard to Chapter 21 of the

cross-sectional area of base cab le, strand,

For Cs, refer to International Building Code (IBC)

height abo ve the base of the w all to the

as defined in Section R9.2.4, ft (m)

IBP refers to the h ydrodynamic design in which it is necess ary

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

overturning moment at the base of the tank,

unit equivalent hydrodynamic pressure due

unit lateral dynamic convective pressure distributed

unit lateral inertia force due to w all dead weight,

total hydrostatic force occurring on length B

For a schematic representation of Ph, refer to Fig. R5.3.1(a)

unit shear force in circular tanks, lb/ft (kN/m)

inside radius of circular tank, ft (m)

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

mapped maxim um considered ear thquake

generalized design spectral response acceleration

spectral displacement, ft (m)

maximum considered earth quake spectral

design spectral response acceleration, 5%

natural per iod of vibr ation of v ertical liquid

polar coordinate angle, degree

coefficients as defined in Section R4.2

For , refer to Fig. R5.2.1 and R5.2.2.

SEISMIC DESIGN OF LIQUID-CONTAINING CONCRETE STRUCTURES

CHAPTER 2TYPES OF LIQUID-CONTAINING STRUCTURES

Structures in this category include rectangular and

2.1.1Ground-supported liquid-containing str uctures

R2.1.1The classif ications of Section 2.1.1 are based

The tank floor and floor support system should be designed