Omron JX Quick Start Guide

Cat. No.
I128E-EN-01
JX
Compact and complete

Model: 3G3JX
200 V Class Three-Phase Input 0.2 to 7.5 kW
200 V Class Single-Phase Input 0.2 to 2.2 kW
400 V Class Three-Phase Input 0.4 to 7.5 kW
QUICK START GUIDE
Notice:
OMRON products are manufactured for use according to proper procedures
by a qualified operator and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this
manual. Always heed the information provided with them. Failure to heed precautions can result in injury to people or damage to property.
OMRON Product References

All OMRON products are capitalized in this manual. The word Unit is also
capitalized when it refers to an OMRON product, regardless of whether or not
it appears in the proper name of the product.
OMRON, 2012
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of
OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover, because OMRON is constantly striving to improve its high-quality products, the information contained in this manual is subject to change without
notice. Every precaution has been taken in the preparation of this manual. Nevertheless, OMRON assumes no responsibility
for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.
JX Quick Start Guide

1 SPECIFICATIONS ................................................................................. 3
1.1 Upon receipt ......................................................................................................................... 3
1.2 Power ratings........................................................................................................................ 3
1.3 Technical specifications ....................................................................................................... 4
2 INSTALLATION..................................................................................... 5
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Wiring sizes and protection .................................................................................................

Installation dimensions........................................................................................................
Installation environment .....................................................................................................
Wiring overview...................................................................................................................
Power wiring ........................................................................................................................
Control wiring......................................................................................................................
Digital inputs SINK/SOURCE (NPN/PNP) settings .........................................................
5
5
6
7
7
8
9
3 PROGRAMMING JX ........................................................................... 10
3.1 Digital operator..................................................................................................................
3.2 Keypad navigation .............................................................................................................
3.3 Parameter initialization.....................................................................................................
3.4 Basic settings ......................................................................................................................
3.5 Ramps adjustment .............................................................................................................
3.6 DC injection braking..........................................................................................................
3.7 V/F curve............................................................................................................................
3.8 Torque boost function ........................................................................................................
3.9 Digital inputs......................................................................................................................
3.10 Digital outputs .................................................................................................................
3.11 Analog inputs ...................................................................................................................
3.12 Analog output AM terminal............................................................................................
3.13 Electronic thermal function.............................................................................................
3.14 Carrier frequency.............................................................................................................
3.15 PID function.....................................................................................................................
3.16 Overload limit/warning ...................................................................................................
3.17 Overvoltage control function ...........................................................................................
3.18 Controlled stop at power loss...........................................................................................
10
11
12
12
13
14
15
16
17
19
19
20
21
22
22
23
23
24
4 PARAMETER LIST .............................................................................. 25

4.1
4.2
4.3
4.4
4.5
4.6
Parameter group D: Monitors ..........................................

Parameter group A ..................................................
Parameter group B ..................................................
Parameter group C ..................................................
Parameter group H ..................................................
Parameter group F ...................................................
25
25
27
29
30
30

1 SPECIFICATIONS
1.1 Upon receipt
Please perform the following task after receiving the drive:
Inspect the driver for damage. If the drive appear damage upon receipt, contact your supplier.
Verify the receipt of the correct model by checking the information on the nameplate. If you have received the wrong model contact your
supplier.
Refer to the Users Manual for detailed information about the product and functions.
Basic specifications and optional EMC filter

Voltage
1 x 200 V
3 x 200 V
3 x 400 V
Type
3G3JX-
Max Motor (KW)
Rated output current (A)
AB002
0.2
1.4
AB004
0.4
2.6
AB007
0.75
4.0
AB015
1.5
7.1
AB022
2.2
10.0
A2002
0.2
1.4
A2004
0.4
2.6
A2007
0.75
4.0
A2015
1.5
7.1
A2022
2.2
10.0
A2037
3.7
15.9
A2055
5.5
24.0
A2075
7.5
32.0
A4004
0.4
1.5
A4007
0.75
2.5
A4015
1.5
3.8
A4022
2.2
5.5
A4040
4.0
8.6
A4055
5.5
13.0
A4075
7.5
16.0
EMC filter
AX-FIJ1006-RE
AX-FIJ1010-RE
AX-FIJ1026-RE
AX-FIJ2006-RE
AX-FIJ2020-RE
AX-FIJ2040-RE
AX-FIJ3005-RE
AX-FIJ3011-RE
AX-FIJ3020-RE
1.2 Power ratings

Motor (kW)
Single-phase 200 V: 3G3JXThree-phase 200 V: 3G3JXApplicable motor capacity

Inverter capacity (KVA)
Output
characteristics
200 V
240 V

Max. output voltage
Max. output frequency
AB002
A2002
0.2
0.4
0.5
1.4
AB004
A2004
0.4
0.9
1.0
2.6
3.1
1.8
5.8
3.4
Rated input voltage and frequency

Power supply
Rated input current (A) single-phase 200 V

Rated input current (A) three-phase 200 V
Allowable voltage fluctuation
Allowable frequency fluctuation
Built-in filter
Braking torque
At short-time deceleration
At capacitor feedback
Cooling method
Approx. 50%
AB007
AB015
AB022
A2007
A2015
A2022
A2037
0.75
1.5
2.2
3.7
1.3
2.4
3.4
5.5
1.6
2.9
4.1
6.6
4.0
7.1
10.0
15.9
Proportional to input voltage: 0 to 240 V
400 Hz
Single-phase 200 to 240 V 50/60 Hz
Three-phase 200 to 240 V 50/60 Hz
9.0
16.0
22.5
5.2
9.3
13.0
20.0
-15% to +10%
+5%
EMC filter (C1 single phase)
50% for
3-phase
Approx. 20% to 40%
20 to 40% for
A2055
5.5
8.3
9.9
24.0
A2075
7.5
11.0
13.3
32.0
30.0
40.0
Approx. 20%
1-phase
Self cooling
Forced-air-cooling
SPECIFICATIONS
Motor (kW)
Three-phase 400 V: 3G3JXApplicable motor capacity

380 V
480 V
Inverter capacity (KVA)

Output
characteristics
Power supply

Max. output voltage
Max. output frequency
Rated input voltage and frequency
Rated input current (A)
Allowable voltage fluctuation
Allowable frequency fluctuation
A4004
0.4
0.9
1.2
1.5
A4007
0.75
1.6
2.0
2.5
2.0
3.3
Built-in filter
Braking torque
At short-time deceleration
At capacitor feedback
Cooling method
Approx. 50%
Self cooling
A4015
A4022
A4040
1.5
2.2
4.0
2.5
3.6
5.6
3.1
4.5
7.1
3.8
5.5
8.6
Proportional to input voltage: 0 to 480 V
400 Hz
3-phase 380 to 480 V 50/60 Hz
5.0
7.0
11.0
-15% to +10%
+5%
EMC filter C2 class
Approx. 20% to 40%
A4055
5.5
8.5
10.8
13.0
A4075
7.5
10.5
13.3
16.0
16.5
20.0
Approx. 20%
Forced-air-cooling
1.3 Technical specifications
Control functions
Model number 3G3JXControl methods

Output frequency range
Frequency precision
Resolution of frequency set value
Resolution of output frequency
Overload capability
Frequency set value
V/f characteristics
Functionality
Input signals
Output signals
Standard functions
Analogue inputs
Accel/Decel times
Ambient conditions
Protection functions
Display
Motor overload protection

Instantaneous overcurrent
Overload
Overvoltage
Momentary power loss
Cooling fin overheat
Stall prevention level
Ground fault
Power charge indication
Degree of protection
Ambient humidity
Storage temperature
Ambient temperature
Installation
Installation height
Vibration
Specifications
Phase-to-phase sinusoidal modulation PWM (V/F)
0.5 to 400 Hz
Digital set value: 0.01% of the max. frequency
Analogue set value: 0.4% of the max. frequency (25 10 C)
Digital set value: 0.1 Hz
Analogue set value: 1/1000 of maximum frequency
0.1Hz
150% rated output current for one minute
0 to 10 VDC (10 k), 4 to 20 mA (250 ), frequency setting volume (selectable), RS485 Modbus
Constant/reduced torque
FW (forward), RW (reverse), CF1 to CF4 (multi-step speed), JG (jogging), DB (external DC injection braking), SET (2nd function), 2CH
(2-step acceleration/deceleration), FRS (free run), EXT (external trip), USP (USP function), SFT (soft lock), AT (analog current input
function selection), RS (reset), PTC (thermistor input), STA (3-wire startup), STP (3-wire stop), F/R (3-wire forward/reverse), PID (PID
selection), PIDC (PID integral reset), UP (UP of UP/DWN function), DWN (DWN of UP/DWN function), UDC (data clear of UP/DWN
function), OPE (forced OPE mode), ADD (frequency addition), F-TM (forced terminal block), RDY (operation ready), SP-SET (special
setting), EMR (emergency shutoff)
RUN (signal during operation), FA1 (frequency arrival signal 1), FA2 (frequency arrival signal 2), OL (overload warning signal), OD (PID
excess deviation signal), AL (alarm signal), DC (analog input disconnection detection signal), FBV (PID FB status output), NDc (network
error), LOG (logical operation result), ODc (communication option disconnected), LOC (light load signal)
AVR function, V/F characteristics selection, upper/lower limit, 16-step speeds, starting frequency adjustment, jogging operation, carrier
frequency adjustment, PID control, frequency jump, analog gain/bias adjustment, S-shape acceleration/deceleration, electronic thermal
characteristics/level adjustment, retry function, simplified torque boost, trip monitor, soft lock function, frequency conversion display,
USP function, 2nd control function, motor rotation speed UP/DWN, overcurrent suppression function.
2 analogue inputs 0 to 10 V (20 k), 4 to 20 mA (250 )
0.01 to 3600.0 s (line/curve selection), 2nd accel/decel setting available
Status indicator LEDs Run, Program, Power, Alarm, Hz, Amps, Volume Led indicator
Digital operator: Available to monitor frequency reference, output current, output frequency
Electronic Thermal overload relay and PTC thermistor input
180% of rated current
150% for 1 minute
790 V for 400 V type and 395 V for 200 V type
Following items are selectable: alarm, 0 Hz start, frequency output at interruption, maximum frequency
Temperature monitor and error detection
Selectable level applicable only at constant speed or during acceleration and constant speed
Detected at power-on
On when power is supplied to the control part
IP20
90% RH or less (without condensation)
-20C to +65C (short-term temperature during transportation)
-10C to 50C (both the carrier frequency and output current need to be reduced at over 40C)
Indoor (no corrosive gas, dust, etc.)
Max. 1000 m
5.9 m/s2 (0.6 G), 10 to 55 Hz (complies with the test method specified in JIS C0040 (1999).)
INSTALLATION
2 INSTALLATION
2.1 Wiring sizes and protection
Motor output (kW)
Inverter model 3G3JX-
0.2
A2002
Wiring
Power cable (mm )
Earth leakage breaker (ELB)
1.25
5A
A2004
0.4
Applicable device
2
Fuse size (class J) Rated 600 V

10 A
10 A
1.25
5A
A2007
2.0
10 A
A4007
1.25
5A
6A
A2015
2.0
15 A
15 A
A4015
2.0
10 A
10 A
A2022
2.0
20 A
20 A
A4022
2.0
10 A
10 A
A2037
3.5
30 A
30 A
A4040
2.0
15 A
15 A
A2055
5.5
50 A
40 A
A4055
3.5
30 A
20 A
A2075
8.0
60 A
50 A
A4075
3.5
30 A
25 A
0.2
AB002
2.0
5A
14 A
0.4
AB004
2.0
5A
0.75
AB007
2.0
10 A
1.5
AB015
5.5
15 A
2.2
AB022
5.5
20 A
A4004
0.75
1.5
2.2
3.7
5.5
7.5
3A
15 A
2.2 Installation dimensions

Fig ure 1
Fig ure 2
W
W1
5
6
W
W1
5
6
H1
H
H1
H
t1
5
Voltage class
Single-phase
200 V
Three-phase
200 V
Max. applicable
motor output kW
0.2
0.4
0.75
1.5
2.2
0.2
0.4
0.75
1.5
2.2
3.7
5.5
7.5
D1
1.9
t1
D1
Inverter model 3G3JXAB002

AB004
AB007
AB015
AB022
A2002
A2004
A2007
A2015
A2022
A2037
A2055
A2075
1.9
Figure
W1
H1
67
143
80
98
176
110
Dimensions in mm
H
D
95.5
155
109.5
130.5
189
157.5
t1
2.6
D1
13
27
28
55
2.6
13
27
50
67
143
80
155
95.5
109.5
132.5
98
176
110
189
157.5
55
164
235
180
250
167.5
1.6
77.5
Weight (kg)
0.8
0.9
1.5
2.3
2.4
0.8
0.9
1.1
2.2
2.4
4.2
INSTALLATION
Voltage class
Three-phase
400 V
Max. applicable
motor output kW
0.4
0.75
1.5
2.2
4.0
5.5
7.5
Inverter model 3G3JX-
Figure
A4004
A4007
A4015
A4022
A4040
A4055
A4075
W1
H1
Dimensions in mm
H
D
130.5
98
176
110
189
164
235
180
250
t1
2.6
D1
28
157.5
55
167.5
1.6
77.5
Weight (kg)
1.5
2.3
2.4
4.2
INSTALLATION
2.3 Installation environment

Increased ambient temperature will shorten the life of the inverter.
Keep the inverter away from heating elements (such as a braking resistor, DC reactor, etc.). If the inverter is installed in a control panel, keep the ambient temperature within the range of the specifications, taking dimensions and ventilation into consideration.
10 cm min.
Airflow
Wall
5 cm min.
5 cm min.
10 cm min.
You can install multiple 3G3JX inverters side by side in the control panel (side-by-side installation). Again, keep the ambient
temperature within the specified range (40C or below).
If the ambient temperature is from 40C through to 50C, the carrier frequency should be reduced and the inverter capacity
should be increased.
INSTALLATION
2.4 Wiring overview

3-phase 200 VAC
1-phase 200 VAC
3-phase 400 VAC
Inverter
R (L1)
U/T1
S (L2)
V/T2
T/N (L3)
W/T3
For Source logic
Note:
To connect the DC reactor,
remove the short-circuit bar.
P24
4.7 k
Motor
PD/+1
DC reactor
4
P/+
3
2
1
N/PCS
AL1
L
AL2
AL0
Frequency
meter
Relay output
Common
AM
11
10 VDC
H
Frequency
setting unit
1 to 2 k
RY
O
10 k
OI
L
Power supply input

4 to 20 mA DC
250
24 VDC
CM2
2.5 Power wiring

Terminal name
R/L1, S/L2, T/N/L3
Main circuit power supply unit
U/T1, V/T2, W/T3
Inverter output
PD/+1, P/+
P/+, N/-
Purpose
External DC reactor terminal
Details
Used to connect line power to the drive
Drives with single-phase 200 V input power use only terminals R/L1 and N (T/L3), terminal S/L2 is not
available for these units
Used to connect the motor
Normally connected by the short-circuit bar. Remove the short-circuit bar between +1 and P/+2 when a
DC reactor is connected
Regenerative braking unit connection

terminal
Connect optional regenerative braking units (if a braking torque is required)
Grounding
For grounding (grounding should conform to the local grounding code)
INSTALLATION
Main circuit terminal block
Model (3G3JX-)
Screw size
W (mm)
Upper side of the body

R/L1
S/L2
7.1
T/L3
Lower side of the body

N/-
AB002 to AB004
A2002 to A2007 *1
M3.5
7.1
P/+ PD+1
Main Circuit
Terminal Block
U/T1 V/T2 W/T3
Upper side of the body

R/L1 S/L2 T/L3
A2015 to A2037
A4004 to A4040
AB007 to AB022 *1
M4
9.2
A2055 to A2075
A4055 to A4075
M5
13
9.2 or 13
Lower side of the body

U/T1 V/T2 W/T3
N/-
P/+
PD+1
Main Circuit
Terminal Block
*1. For 3G3JX-AB, R/L1 corresponds to L1 and T/L3 to N, terminal S/L2 is not available. Connect a single-phase 200 VAC input to terminals L1 and N.
2.6 Control wiring
Relay
output
AL2 AL1 AL0
Analog Frequency
monitor reference
output
input
AM H
OI
Multi-function input
5
2 1
Multi-function
output
L PCS P24
CM2
11
Short-circuit bar
Type
Digital
input
signals
Analog
input
signals
No.
Signal name
Function
PCS
Input power supply
External power supply terminal for input signal (input)

...At sink logic
Internal power supply output terminal for input signal (output)
...At source logic
P24
Internal 24 VDC
24 VDC internal power supply
Multi-function input selection 1
Factory setting: Forward/Stop
Factory setting: Reverse/Stop
Factory setting: Fault reset
Factory setting: Emergency stop fault
Factory setting: Multi-step speed reference 1
Multi-function input selection common
Frequency reference power supply
10 VDC 10 mA max
Voltage frequency reference signal
0 to 10 VDC (10 k)
OI
Current frequency reference signal
4 to 20 mA (250 )
Frequency reference common
Signal level
24 VDC 10%
24 VDC 10%, 100 mA
27 VAC max
ON voltage: 18 V min
OFF voltage: 3 V max
Load current: 5 mA
Min ON time: 12 ms
INSTALLATION
AL2
Digital
output
signals
Factory default relay settings

Under normal operation: AL2-AL0 closed
Under abnormal operation: AL1-AL0 open
AL1
NO output
AL0
Relay output common
250 VAC 1 A
30 VDC 1 A
5 V, 100 mA min
Multi-function output terminal
Factory setting: Frequency arrival signal at a constant speed
CM2
Output signal common
AM
Analog frequency monitor/Analog output current monitor
Factory setting: Analog frequency monitor
11
Monitor
signal
250 VAC 2.5 A

30 VDC 3 A
NC output
27 VDC
50 mA max
0 to 10 VDC, 1 mA
2.7 Digital inputs SINK/SOURCE (NPN/PNP) settings

Sinking internal supply (for NPN outputs)
+V
Sinking external supply (for NPN outputs)
+V
P24
Short-circuit
bar
PCS
L
P24
PCS
24 V DC
24 V DC
1
5
5
COM
COM
Output unit etc.
Inverter
Output unit etc.
Sourcing internal supply (for PNP outputs)
COM
10
COM
24 V DC
24 V DC
P24
PCS
L
0V
Output unit etc.
Inverter
Sourcing external supply (for PNP outputs)
P24
Short-circuit PCS
bar
L
DC24V
24 V DC
0V
Inverter
Output unit etc.
Inverter
PROGRAMMING JX
3 PROGRAMMING JX
3.1 Digital operator
Data display
RUN command LED indicator
FREQ adjuster
Operation keys
Item
8888
Name
POWER LED indicator
Description
Lit when the power is supplied to the control circuit.
ALARM LED indicator
Lit when an inverter error occurs.
RUN (during RUN) LED indicator
Lit when the inverter is running.
PROGRAM LED indicator
Lit when the set value of each function is indicated on the data display.
Blinks during warning (when the set value is incorrect).
Displays relevant data, such as frequency reference, output current and set values.
Data display
Data display LED indicator
Volume LED indicator
Lit according to the indication on the data display.

Hz: Frequency
A: Current
Lit when the frequency reference source is set to the FREQ adjuster.
FREQ adjuster
Sets a frequency. Available only when the frequency reference source is set to the
FREQ adjuster. (Check that the Volume LED indicator is lit.)
RUN command LED indicator
Lit when the RUN command is set to the Digital operator. (The RUN key on the
Digital operator is available for operation.)
Activates the inverter. Available only when operation via the Digital operator is
selected. (Check that the RUN command LED indicator is lit.)
Forward/Reverse rotation depends on F004 setting.
RUN key
STOP/RESET key
Decelerates and stops the inverter. Functions as a reset key if an inverter error
occurs.
Mode key
Switches between: the monitor mode (d@@@), the basic function mode (F@@@),
and the extended function mode (A@@@, b@@@, C@@@, H@@@).
With this key, you can always change the display as follows.
[Supplemental information]
To jump to d001 from any function mode, hold down the Mode key for 3
seconds.
58.1
or
f001
58.0
f001
57.9
Enter key
Increment key
Decrement key
Note: Always press the Enter key to store any changed data.
Enters and stores changed data.
(To change the set value, be sure to press the Enter key.)
Do not press the Enter key if you dont want to store any changes, for example, if
you have changed the data inadvertently.
Changes the mode.
Also, increases the set value of each function.
Changes the mode.

Also, decreases the set value of each function.
11
PROGRAMMING JX
3.2 Keypad navigation

*4
d001
*4
0.0
*4
Press the key
d083
*4
f001
*5
f004
*3
a001
*1
*5
a---
0000
a001
*2
0001 9999
*5
b---
a002
c---
*1
*2
0000
0001 9999
*5
h---
a003
*1. Data is not stored by pressing the Mode key.

*2. Press the Enter key to store the data.
*3. When you press the Mode key after you return to the parameter number display without storing data in the extended function mode, the mode selection function is selected.
*4. When you press the Enter key with d@@@ or F001 displayed, the monitor value is stored as the initial display that appears
when the power is turned on.
*5. When you press the Enter key, the first digit of each parameter setting is stored as the initial display that appears when the
power is turned on.
(Example: f002 , a--- , etc.)
* To display a specific monitor when the power is turned on, press the Enter key with that monitor displayed. If a parameter for
an extended function code is stored after pressing the Enter key, however, that code (A@@@, b@@@, C@@@, d@@@ or
H@@@) appears at the next power-on. To prevent this, always press the Enter key again with the desired monitor displayed after
storing a parameter.
12
PROGRAMMING JX
3.3 Parameter initialization

Initialize the parameters using the following procedure.
To initialize the parameters, set parameter b084 to 02.
Key sequence
Display example
0.0
b--b001
b084
00
02
b084
Description
Power On
Press the Mode key once, and then press the Decrement key three times to
display b---.
Press the Mode key.

b001 is displayed.
Use the Increment or Decrement key to display b084.
Press the Mode key. The set value in b084 is displayed.
Use the Increment or Decrement key to display 02.
Press the Enter key. The set value is entered and b084 is displayed.
Press the STOP/RESET key while holding down the Mode and Decrement
keys simultaneously.
When the display blinks, release the STOP/RESET key first, and then the
Mode and Decrement keys.
-. 00
(In 1 s)
d001
Displays initialization.
The parameter number is displayed again in approximately 1 s.
3.4 Basic settings

After selecting the inverter mode follow next steps for a basic operation of the inverter
Select frequency reference source on parameter A001

Parameter
A001
A201
Parameter name
Frequency reference selection
Details
00: Digital operator (FREQ adjuster)
01: Terminal
2nd frequency reference selection 02: Digital operator (F001)
03: ModBus communication
10: Frequency operation result
13
PROGRAMMING JX
Select Run command source on parameter A002

Parameter
A002
Parameter name
RUN command selection
2nd RUN command selection
A202
Details
01: Terminal
02: Digital operator
03: ModBus communication
Adjust the stopping method by b091 and the acceleration/deceleration ramps on parameters F002 and F003
Parameter
b091
Parameter name
Stop selection
F002
F202
F003
F203
Details
00: Deceleration to stop
01: Free-run stop
0.01 to 3000. s
Acceleration time 1
2nd acceleration time 1
Deceleration time 1
2nd deceleration time 1
0.01 to 3000. s
Set the motor base frequency and AVR voltage of the motors in parameters A003 and A082
Parameter
A003
A203
A082
Parameter name
Base frequency
2nd base frequency
AVR voltage selection
Details
30. to Max. frequency [A004]
30. to Max. frequency [A204]
200-V class: 200/215/220/230/240 V
400-V class: 380/400/415/440/460/480 V
Set the motor data: rated current (b012), rated power (H003) and number of poles (H004)
Parameter
b012
b212
H003
H203
H004
H204
Parameter name
Electronic thermal level
2nd electronic thermal level
Motor capacity selection
2nd motor capacity selection
Motor pole number selection
2nd motor pole number selection
Details
0.2 x Rated current to 1.0 x Rated current
200-V class: 0.2/0.4/0.75/1.5/2.2/3.7/5.5/7.5 kW
400-V class: 0.4/0.75/1.5/2.2/3.7/5.5/7.5 kW
2/4/6/8 poles
At this point the inverter is ready to run the motor for the first time, but first review this check-list:
Verify the power LED is ON. If not, check the power connections.
Make sure the motor is disconnected from any mechanical load.
Make sure that you have a frequency reference checking the content of F001.
Now give the RUN command from the selected source. The RUN LED will turn ON.
The motor should start turning.
Remove the RUN command or press the STOP key to stop the motor rotation.
3.5 Ramps adjustment

The basic frequency (speed) profile is defined by parameters contained in the F Group as shown to the right. The set running frequency is in Hz, but acceleration and deceleration are specified in
the time duration of the ramp (from zero to maximum frequency,
or from maximum frequency to zero).
Output frequency
Max. frequency
A004/A204
Output frequency set value
Acceleration 1 and Deceleration 1 are the standard default accel

and decel values for the main profile. Accel and decel values for an
alternative profile are specified by using parameters A092 through
A093.
Actual
acceleration
time
F002/F202
Parameter
A004
A204
b082
F001
F002
F202
14
Parameter name
Maximum frequency
2nd maximum frequency
Starting frequency
Output frequency setting/monitor
Acceleration time 1
Actual
deceleration
time
F003/F203
Description
30. to 400. Hz
0.5 to 9.9 Hz
Starting frequency to 1st or 2nd max. frequency
0.01 to 3000. s
PROGRAMMING JX
F003
F203
Deceleration time 1
0.01 to 3000. s
Standard acceleration and deceleration is linear. The inverter CPU can also calculate an S-curve acceleration or deceleration
curve as shown. Even if the shape of the ramps change the time keeps being the same one set in F002/F003.
Curve settings for acceleration and deceleration are independently selected. To enable the S-curve, use function A097 (acceleration) and A098 (deceleration).
Parameter
A097
A098
Parameter name
Acceleration pattern selection
Deceleration pattern selection
Description
00: Line
01: S-shape curve
This table shows the different acceleration shapes:

Set value
Parameter no.
00
01
Line
S-shape curve
Output frequency
Output frequency
A097
(Acceleration)
Time
Output frequency
A098
(Deceleration)
Output frequency
Time
Time
Description
Accelerates/decelerates linearly before reaching the

set output frequency value.
Time
Helps prevent the collapse of cargo on the elevating

machine or conveyor.
3.6 DC injection braking

The DC injection braking feature can provide additional stopping torque during deceleration or before acceleration and is particularly useful at low speeds when normal deceleration torque is minimal. This function injects a DC voltage into the motor windings which generates a DC current that force the motor to stop.
There are several modes available depending on the application requirements:
Normal DC injection braking is used when A051 is set to 01 (Enable during stop) and the RUN command (FW/RV) is
turned OFF, at the moment that deceleration stops the DC injection brake starts with a settable power (A054) and duration
(A055). Additionally is possible to specify a wait time between the end of the ramp and the DC injection braking on parame-
15
PROGRAMMING JX
ter A053, during which the motor will free run. If free-run is selected as stopping method the DC injection braking will start
just when the Run commands turns OFF.
DC Brake at stop
FW
ON
F-SET
A053
A055
F-OUT
DB
A053
DC injection braking by frequency detection can be selected setting A051 to 02 (Frequency control). In this case DC injection braking operates when the output frequency comes down to the one you specified in A052 while the RUN command is
still active. External DB and internal DC injection braking are invalid during the frequency detection mode.
FW
FW
ON
F-SET
F-SET
A052
A052
F-OUT
F-OUT
ON
DB
DB
Eample 1: Step change in F-SET
DB
DB
Example 2: Analog change in F-SET
Last option is to trigger the DC injection by a digital input when the terminal (DB) is turned ON. Set parameters A053 and
A054 to setup this function. There are several cases depending on the motor rotation and Run command status.
[FW,RV]
[DB]
Run from operator with delay
Run from operator
FW or RV DI are ON
1
0
1
0
1
0
1
0
1
0
1
0
delay
A053
F-OUT
Parameter
16
Parameter name
Description
A051
DC injection braking selection
00: Disabled
01: Enabled
02: Frequency control [A052 set value]
A052
DC injection braking frequency
0.0 to 60.0 Hz
PROGRAMMING JX
Parameter
Parameter name
Description
A053
DC injection braking delay time
The delay from the end of controlled deceleration to start of DC

braking (motor free runs until DC braking begins)
0.0 to 5.0 s
A054
DC injection braking power
0. to 100.%
A055
DC injection braking time
Sets the duration for DC braking

0.0 to 60.0 s
A056
DC injection braking method

selection
00: Edge operation

01: Level operation
Be careful to avoid specifying too long braking time or too high carrier frequency that can cause motor overheating. If you use
DC injection braking is recommended to use motors with a built-in thermistor and wire it to inverters thermistor input.
3.7 V/F curve

The inverter generates the motor output according to the V/F algorithm selected on parameter A044. The factory default is Constant torque (00). Review following descriptions to help you choose the best torque control algorithm for your application:
Parameter
Parameter name
Description
A044
V/F characteristics selection
A244
2nd V/F characteristics selection
00: Constant torque characteristics (VC)

01: Reduced torque characteristics (VP 1.7th power)
06: Special reduced torque characteristics (Special VP)
Constant torque characteristics (VC) - Output voltage is proportional to output frequency. While proportional from 0 Hz to
base frequency, the output voltage is constant from base to maximum frequencies regardless of the frequency.
Output
voltage
(100%)
Output
frequency (Hz)
0
Base frequency Max. frequency

(A003/A203)
(A004/A204)
Reduced torque characteristics (VP 1.7th power) - Suitable for a fan or pump that does not require large torque in a low
speed range. These provide high efficiency, reduced noise and vibration, owing to reduced output voltage in a low speed
range.
Output
voltage
(100%)
VP (1.7th
power of VP)
Output
frequency (Hz)
0
(A004/A204)
(A003/A203)
Special reduced torque characteristics (Special VP) - Suitable for a fan or pump that requires torque in a low speed range
using VC characteristics at this area.
Output
voltage
(100%)
VP
(1.7th power)
VC
Output
frequency (Hz)
0
10% of base
frequency
a

(A003/A203)
(A004/A204)
b
Period a: Provides constant torque characteristics (VC) within a range from 0 Hz to 10% of base frequency. (Example) If the
base frequency is 50 Hz, the inverter provides constant torque characteristics within a range from 0 to 5 Hz.
Period b: Provides reduced torque characteristics within a range from 10% to 100% of the base frequency. The inverter outputs voltage based on a curve of the 1.7th power of the frequency.
17
PROGRAMMING JX
Period c: Provides constant voltage within a range from the base frequency to the maximum frequency.
3.8 Torque boost function

This function helps to compensate insufficient motor torque in a low speed range.
Compensates the voltage drop caused by the primary resistance of the motor or wiring increasing the torque in a low speed
range.
To select the simple torque boost in the torque boost selection (A041/A241), set the motor capacity selection (H003/H203)
and motor pole number selection (H004/H204) according to your motor.
18
PROGRAMMING JX
Manual torque boost (A042/A242, A043/A243)
Adds the voltage set in A042/A242 and A043/A243 to the V/F

characteristics, and outputs the resulting voltage. The addition
value is set in percentage terms based on the AVR voltage
selection (A082) as 100%.
The manual torque boost frequency (A043/A243) is set in per-
Output
voltage (100%)
Manual torque
boost voltage
(A042/A242)
V/f characteristics
(Example: VC)
centage terms based on the base frequency as 100%.

0
If you raise the set value of the manual torque boost (A042/
A242) be careful about motor overexcitation. Otherwise the
motor may burn out.
Manual torque boost

frequency (A043/A243)

(A003/A203)
(A004/A204)
Output frequency (Hz)
Simple torque boost (A041/A241)
If simple torque boost is selected in the torque boost selection (A041/A241: 01), it operates to adjust the output voltage
depending on the load level.
To select simple torque boost in the torque boost selection (A041/A241), set the motor capacity selection (H003/H203) and
motor pole number selection (H004/H204) according to your motor.
You may avoid a possible overcurrent trip during deceleration by always setting the AVR selection to ON (A081: 00).
Sufficient characteristics may not be obtained if you select two or more lower rank motor size than specified.
Parameter
Parameter name
A041
Description
Torque boost selection
00: Manual torque boost only

01: Automatic (simple) torque boost
A241
2nd torque boost selection
A042
Manual torque boost voltage
A242
2nd manual torque boost voltage
A043
Manual torque boost frequency
A243
2nd manual torque boost frequency
Can boost starting torque between 0 and 20% above normal V/f
curve
0.0 to 20.0%
Sets the frequency of the V/f breakpoint for torque boost
0.0 to 50.0%
3.9 Digital inputs

The function codes in the following table let you assign between a wide range of functions to any of the five logic inputs for the
3G3JX inverter. The functions C001 through C005 configure the terminals [1] through [5] respectively. The value of these particular parameters is not a scalar value, but it is a discrete number that selects one option from many available options.
Input function summary table
Option
code
Terminal
symbol
00
FW
01
RV
Function name
Forward command
Reverse command
02
CF1
Multi-step speed setting binary 1
03
CF2
04
CF3
05
CF4
Description
ON
Inverter is in Run Mode, motor runs forward
OFF
Inverter is in Stop Mode, motor stops
ON
Inverter is in Run Mode, motor runs reverse
OFF
Inverter is in Stop Mode, motor stops
ON
Binary encoded speed selection bit 3 to bit 0
OFF
06
JG
Jogging
ON
Inverter is in Run Mode, output to motor runs at jog parameter frequency
07
DB
External DC injection braking
ON
DC injection braking will be applied during deceleration
08
SET
2nd control selection
ON
The inverter uses 2nd motor parameters for generating frequency output to motor
09
2CH
2-step acceleration/deceleration
11
FRS
Free-run stop
12
EXT
External trip
13
15
16
USP
SFT
AT
Power recovery restart protection

Soft lock
Analog input switching
OFF
The inverter uses 1st (main) motor parameters for generating frequency output to motor
ON
Frequency output uses 2nd-stage acceleration and deceleration values
OFF
Frequency output uses standard acceleration and deceleration values
ON
Causes output to turn OFF, allowing motor to free run (coast) to stop
ON
When assigned input transitions OFF to ON, inverter latches trip event and displays E 12
OFF
No trip event for ON to OFF, any recorded trip events remain in history until reset
ON
The inverter will not resume a Run command
OFF
The inverter will resume a Run command that was active before power loss
ON
The keypad and remote programming devices are prevented from changing parameters
OFF
The parameters may be edited and stored
ON
Refer to Analog Input selection
OFF
19
PROGRAMMING JX

Option
code
Terminal
symbol
18
RS
Function name
Reset
Description
ON
The trip condition is reset, the motor output is turned OFF, and powerup reset is asserted
OFF
Normal power-ON operation
ON
The inverter can detect motor temperature and, if the temperature exceeds the specified level, trips
to shut off the output (E35). The level is fixed.
19
PTC
Thermistor input
20
STA
3-wire start
21
STP
3-wire stop
ON
Stops the motor rotation
22
F/R
3-wire forward/reverse
ON
Selects the direction of motor rotation: ON = FWD. While the motor is rotating, a change of F/R
will start a deceleration, followed by a change in direction
OFF
Selects the direction of motor rotation: OFF = REV. While the motor is rotating, a change of F/R
will start a deceleration, followed by a change in direction
ON
Temporarily disables PID loop control. Inverter output turns OFF as long as PID Enable is active
(A071=01)
23
PID
24
PIDC
PID enabled/disabled
OFF
If the thermistor is not connected, the inverter trips (E35) to shut off the output
ON
Starts the motor rotation
OFF
Has no effect on PID loop operation, operates normally if PID Enable is active (A071=01)
PID integral reset
ON
Resets the PID loop controller. Main consequence is that integrator sum is forced to zero
Accelerates (increases output frequency) motor from current frequency
27
UP
UP/DWN function accelerated
ON
28
DWN
UP/DWN function decelerated
ON
Decelerates (decreases output frequency) motor from current frequency
29
UDC
UP/DWN function data clear
ON
Clears the UP/DWN frequency memory by forcing it to equal the set frequency parameter F001.
31
OPE
Forced operator
ON
Forces the source of the output frequency setting A001 and the source of the Run command A002
to be from the digital operator
50
ADD
Frequency addition
51
F-TM
Forced terminal block
52
RDY
Ready function
53
SP-SET
64
EMR
255
no
Special 2nd function selection

Emergency shutoff
No function
OFF
Source of output frequency set by A001 and source of Run command set by A002 is used
ON
Adds the A145 (add frequency) value to the output frequency
OFF
Does not add the A145 value to the output frequency
ON
Force inverter to use input terminals for output frequency and Run command sources
OFF
Source of output frequency set by A001 and source of Run command set by A002 is used
ON
The inverter is ready
OFF
Normal stop status
ON
Enables the parameter for the special 2nd motor
OFF
Disables the parameter for the special 2nd motor
ON
Emergency shutoff is ON
Digital input not used
All this functions could be assigned to any of the multi-function inputs on parameters C001 to C005, select if the input will be
normally open or normally close and the response time of the input.
Parameter
C001
Parameter name
Multi-function input 1 selection
C201
2nd multi-function input 1 selection
C002
C202
C003
C203
C004
C204
C005
C205
C011
Multi-function input 1 operation selection
C012
C013
C014
C015
Description
Refer to upper table for available settings
00: NO (normally open)

01: NC (normally closed)
An input terminal configured for option code 18 ([RS] Reset command) cannot be configured for normally closed operation.
20
PROGRAMMING JX
3.10 Digital outputs

Function codes in the following table let you assign different options into logical outputs (terminal [11] and [AL]) on parameters
C021 and C026.
Option
code
Terminal
symbol
00
RUN
Signal during RUN
01
FA1
Constant speed arrival signal
Function name
Description
ON
When the inverter is in Run Mode
ON
When output to motor is at the set frequency
OFF
When output to motor is OFF, or in any acceleration or deceleration ramp
ON
When output to motor is at or above the set frequency, even if in acceleration (C042) or
deceleration (C043) ramps
02
FA2
Over set frequency arrival signal
OFF
When output to motor is OFF, or at a level below the set frequency
03
OL
Overload warning
ON
When output current is more than the set threshold (C041) for the overload signal
04
OD
Excessive PID deviation
ON
When PID error is more than the set threshold for the deviation signal
05
AL
Alarm output
ON
When an alarm signal has occurred and has not been cleared
06
Dc
07
FBV
Disconnection detection
ON
When the inverter is in trip status
PID FB status output
ON
Shifts output when exceeding the upper limit or falling below the lower limit
08
NDc
Network error
ON
The communication watchdog timer times out
09
LOG
Logic operation output
ON
This function outputs a logic operation result of combination of two functions
10
ODc
Not used
43
LOC
Light load detection signal
ON
Motor current is less than the specified value (C039)
In the same way of that the digital inputs is possible to choose between normally close and normally open and even is possible to
use some On and Off delay for each of the outputs.
Parameter
Parameter name
C021
Description
Multi-function output terminal 11 selection
C026
Relay output (AL2, AL1) function selection
C031
Multi-function output terminal 11 contact selection
C036
Relay output (AL2, AL1) contact selection
Refer to upper table for available settings

00: NO contact at AL2; NC contact at AL1
01: NC contact at AL2; NO contact at AL1
3.11 Analog inputs

Two types of external analog inputs are available for frequency reference plus the built-in VR. For voltage input, you can set a frequency from 0 to maximum by applying a voltage from 0 to 10 V between inputs O and L. For current input, apply 4 to 20 mA
between inputs OI and L. Note that voltage and current cannot be input simultaneously. Also, do not connect the signal lines for
inputs O and OI simultaneously.
H
OI
A001
[AT]
Reference voltage (10 V)
Frequency setting
Inverter VR
Voltage input
Current input
Analog ground
OI
Switching between the inputs could be done by a digital input setting parameter A005.
Parameter
A005
Parameter name
O/OI selection
Related parameters
Required settings
Data
00: Switches between O/OI via terminal AT
02: Switches between O/FREQ adjuster via terminal AT
03: Switches between OI/FREQ adjuster via terminal AT
04: O input only
05: OI input only
Default setting
Unit
02
A011 to A016, A101 to A105, A151 to A155, C001 to C005. C081, C082
A001= 01
Allocate AT (16) to any of the multi-function inputs with the frequency reference set to the terminal block (A001 or A201 = 01).
Data
Symbol
16
AT
Related parameters
Function name
Analog input switching
Status
Description
ON
Depends on the combination with the A005 setting

(see the below table)
OFF
Same as above
C001 to C005
21
PROGRAMMING JX
The settings are as follows. (VR: FREQ adjuster). If AT is not allocated to any of the multi-function input, this means the AT
input = OFF in the above table.
A005 set value
00
02
03
04
AT terminal input status
OFF
ON
OFF
ON
OFF
ON
Analog input enabled
O-L
OI-L
O-L
VR
OI-L
VR
OFF
05
ON
OFF
O-L
ON
OI-L
3.12 Analog output AM terminal

This function allows you to monitor the output frequency and current from the AM terminal on the control terminal block. Analog voltage output from 0 to 10 V.
AM selection
Select a signal to output from the following table:
Parameter
C028
Parameter name
AM selection
Description
00: Output frequency
01: Output current
Output frequency - Outputs the voltage according to the output frequency, with the maximum frequency being full scale.
This is intended for display indication and cannot be used as a line speed signal. Through the accuracy is 5%, this could be
exceeded depending on your meter. Outputs a frequency obtained by multiplying the output frequency by the conversion
coefficient [b086], with the maximum frequency being full scale.
AM H
OI
Meter
10V, 1mA
Output current - Outputs a current value with 200% of the inverter rated voltage being full scale. The output method is the
same as the output frequency. Monitor accuracy is 10% at the halfway point of base frequency.
AM adjustment
You can adjust the calibration of the analog voltage (0 to 10 VDC) from the AM terminal on the control terminal block by using
the inverter setting.
Parameter
Parameter name
Data
Default setting
Unit
b080
AM adjustment
0. to 255. (adjust to the scale)
100.
C086
AM offset adjustment
0.0 to 10.0 (see the figure below)
0.0
Related parameters
A011 to A015, A101 to A105
Note: If the offset (C086) is changed, the point to reach 10 V changes accordingly because of parallel movement. To avoid this,
adjust the offset (C086) before the gain (b080).
When b080 = 100
When C086 = 0.0

AM output
AM output
10V
b080=0 to 255
10V
C086=0 to 10
Parallel shift
5V
5V
0
1/2 FS
22
Full scale (FS)

Hz or A
1/2 FS
Full scale (FS)

Hz or A
PROGRAMMING JX
3.13 Electronic thermal function

This function electronically protects the motor from overheating.
Causes an overload trip (E05) to protect the motor from overheating by setting according to the motor rated current.
Provides the most appropriate protection characteristics, taking into account the decline of a standard motor cooling capability at a low speed.
To set a value over the rated current of the motor, be careful of any temperature rise of the motor.
Parameter
b012
Parameter name
Description
b212*
b013
Electronic thermal characteristics selection
b213*
2nd electronic thermal characteristics

selection
00: Reduced torque characteristics 1

01: Constant torque characteristics
Related parameters
C021
* To switch to the 2nd control, allocate 08 (SET) to the multi-function input terminal and then turn it on.
Electronic thermal level (motor protection level)
(Example) 3G3JX-AB007, rated current: 4.0 A, setting range: 0.8 to 4.0 A.
Time before trip (s)
Example where electronic
thermal level is b012 = 5.0 A
60
4
0
Motor current (A)

4.6
6.0
8.0 (Ratio to the rated
(116%) (150%)(200%) current of the Inverter)
Electronic thermal characteristics

Frequency characteristics are multiplied by the b012/212 set value above. The lower the output frequency is, the lower the cooling capability of the standard motors self-cooling fan.
Reduced torque characteristics 1 - Multiplied by the time limit characteristics set in b012/212 for each frequency.
Constant torque characteristics - Do not skip this setting when using a constant torque motor. Multiplied by the time limit
characteristics set in b012/212 for each frequency.
Reduced torque characteristics 2 - Multiplied by the limit characteristics set in b012/212 for each frequency.
Constant torque
characteristics
Reduced torque
characteristics 1
Reduced torque
characteristics 2

X1.0
X1.0
X1.0
X0.8
X0.8
X0.667
X0.6
0
20
60
Inverter output
frequency (Hz)
60
Inverter output
frequency (Hz)
20
60
Inverter output
frequency (Hz)
23
PROGRAMMING JX
3.14 Carrier frequency

You can change the PWM waveform carrier frequency output from the inverter.
Parameter
b083
Parameter name
Data
Carrier frequency
Default setting
Unit
3.0
kHz
2.0 to 12.0
With the carrier frequency set high, you can reduce metallic noise from the motor. However, this may increase electrical noise
or leakage current from the inverter.
Carrier frequency adjustment also helps avoid mechanical or motor resonance.

To raise the carrier frequency, reduce the output current (or derate the rated current). Check users manual for details.
3.15 PID function
This function enables process control such elements as flow rate, air volume, and pressure.
Parameter
A071
Parameter name
Data
Default setting
Unit
00
PID selection
00: Disabled
01: Enabled
A072
PID P gain
0.2 to 5.0
1.0
A073
PID I gain
0.0 to 150.0
1.0
A074
PID D gain
0.00 to 100.0
0.0
A075
PID scale
0.01 to 99.99
1.00
Time
A076
PID feedback selection
00: OI
01: O
02: RS485 communication
10: Operation function output
00
A077
Reverse PID function
00: OFF (Deviation = Target value - Feedback value)

01: ON (Deviation = Feedback value - Target value)
00
A078
PID output limit function
0.0 to 100.0
0.0
C044
PID deviation excessive level
0.0 to 100.0
3.0
C052
PID FB upper limit
0.0 to 100.0
100.0
C053
PID FB lower limit

Related parameters
0.0
d004, A001, A005, C001 to C005, C021, C026
To use this function, set A071 to 01.

To switch between enable/disable via the terminal block (external signal), allocate 23 (PID enable/disable) to the desired
multi-function input. Select OFF for enable and ON for disable.
Basic structure of PID control (example)
Control
value
Target value + Deviation
1
Normal control
K p 1+
+ Td s
M
of the Inverter
fs
0 to 10 V Ti s
4 to 20 mA
Feedback
0 to 10 V
4 to 20 mA
Kp: Proportional gain
Ti: Integral time
Td: Derivative time
Sensor
=
Transducer
s: Operator
: Deviation
PID enable/disable
Data
Symbol
23
PID
Related parameters
Function name
PID enabled/disabled
Status
Description
ON
Disables the PID function
OFF
Does not affect the PID function
C001 to C005
Excessive deviation/output
Data
Symbol
04
OD
Function name
Excessive PID deviation
Status
Description
ON
The PID deviation has exceeded the C044 set value
OFF
The PID deviation has not reached the C044 set value
Available output terminals 11-CM2, AL2-AL0 (or AL1-AL0)

Requires settings
24
C021, C026, C044
PROGRAMMING JX
PID feedback (FB) upper/lower limit

Data
Symbol
07
FBV
Function name
PID FB status output
Status
ON
OFF
Description
Shifts output when exceeding the upper limit or falling
below the lower limit
Available output terminals 11-CM2, AL2-AL0 (or AL1-AL0)

Requires settings
C021, C026, C052, C053
PID integral reset

Data
Symbol
24
PIDC
Related parameters
Function name
PID integral reset
Status
Description
ON
Forcibly sets the PID integral value to zero
OFF
Does not affect the PID function
C001 to C005
3.16 Overload limit/warning

This function helps prevent an overcurrent trip due to rapid load fluctuation in acceleration or constant speed operation.
Parameter
Parameter name
b021
Overload limit selection
b221*
2nd overload limit selection
b022
Overload limit level
b222*
2nd overload limit level
b023
Overload limit parameter
b223*
2nd overload limit parameter
b028
Overload limit source selection
b228*
2nd overload limit source selection
C041
Overload warning level
C241*
2nd overload warning level

Related parameters
Data
Default setting
Unit
01
1.5 x Rated
current
0.1 to 3000.0
1.0
00: b022, b222 set values

01: Input terminal O
00
Rated current
00: Disabled
01: Enabled in acceleration/constant speed operation
02: Enabled in constant speed operation
0.0: Does not operate

C021, C026
* To switch to the 2nd control, allocate 08 (SET) to the multi-function input terminal and then turn it on.
The inverter monitors the motor current during acceleration or constant speed operation. If it reaches the overload limit
level, the output frequency is lowered automatically according to the overload limit parameter.
b022
Deceleration set by the overload
limit parameter
Output current
Max. frequency
A004/A204
Inverter output
frequency
Target frequency
F001
b023
For more detailed information please check the users manual.

3.17 Overvoltage control function
This function helps avoid an overvoltage trip during deceleration. Note that the actual deceleration time may be longer than the
set value. This function automatically keeps DC voltage at the set level during deceleration. The aim of this function is the same
as the overvoltage LAD stop function, described in b130 and b131. However, this functions have different deceleration characteristics and you can select either function according to your system.
Parameter
Default setting
Unit
b055
Overvoltage protection proportional

gain during deceleration
0.2 to 5.0
0.2
b056
Overvoltage protection integral time

during deceleration
0.0 to 150.0
0.2
Parameter name
Data
25
PROGRAMMING JX
Parameter
Parameter name
Data
b130
Overvoltage LAD stop function
00: Disabled
01: Enabled
b131
Overvoltage LAD stop function level

setting
200-V class: 330. to 395.

400-V class: 660. to 790.
b133
Overvoltage protection function

selection during deceleration
00: Disabled
01: Enabled
b134
Overvoltage protection level setting

during deceleration
200-V class: 330. to 395.

400-V class: 660. to 790.
Default setting
Unit
00
380/760
00
380/760
Internal DC
voltage
Set level (B134)
t
Output
frequency
t
Normal
Overvoltage protection during deceleration
3.18 Controlled stop at power loss

This function decelerates the inverter by a controlled stop to avoid a trip or free running in case of power supply disconnection
or momentary power interruption during operation.
Parameter
Default setting
Unit
b050
Selection of non-stop function at

momentary power interruption
Parameter name
00: Disabled
01: Enabled (stop)
02: Enabled (restart)
Data
00
b051
Starting voltage of non-stop function

at momentary power interruption
0.0 to 1000.
0.0
b052
Stop deceleration level of non-stop

function at momentary power
interruption
0.0 to 1000.
0.0
b053
Deceleration time of non-stop

function at momentary power
interruption
0.01 to 3000.
1.0
b054
Deceleration starting width of nonstop function at momentary power

interruption
0.0 to 10.0
0.0
Hz
OFF
Power supply
Internal DC
voltage
b052
b051
Undervoltage level
Output frequency
b054
b053
b053
b053
26
PARAMETER LIST
4 PARAMETER LIST
The PDU (Process Data Unit) register number are addressed starting at zero. Therefore register numbered 0012h addressed as
0011h. Register address value (transmitted on Modbus line) is 1 less than the Register number of the table
4.1 Parameter group D: Monitors

Parameter No.
Function name
d001
d002
d003
Output frequency monitor

Output current monitor
Rotation direction monitor
d004
PID feedback value monitor
d005
Multi-function input monitor
Monitoring or data range (digital operator)

0.0 to 400.0
0.0 to 999.0
F: Forward
o: Stop
r: Reverse
0.00 to 9999.
(Enabled when the PID function is enabled)
ON
OFF
5
d006
Multi-function output monitor
ON
OFF
AL2
d007
Output frequency monitor (after conversion)
d013
d016
Changes
during
operation
-
1005 (high)
1006 (low)
1007
1008
1009 (high)
100A (low)
100C
100E (high)
100F (low)
1010 (high)
1011 (low)
116A
0011
0012 to 001B
Default
setting
Unit
Modbus
address (hex)
Hz
A
-
1002
1003
1004
Terminal
4, 2: ON
Terminal
5, 3, 1: OFF
Terminal 11: ON
Terminal AL2: OFF
11
Output voltage monitor

Total RUN time
0.00 to 39960
(Output frequency x Conversion factor of b086)
0. to 600.
0. to 99990 hours
V
h
d017
Power ON time monitor
0. to 99990 hours
d018
d080
d081
Fin temperature monitor

Fault frequency monitor
Fault monitor 1 (Latest)
C
-
d082
Fault monitor 2
d083
Fault monitor 3
d102
d104
DC voltage monitor
Electronic thermal monitor
0.0 to 200.0
0. to 9999.
Error code (condition of occurrence)
Output frequency [Hz]
Output current [A]
Internal DC voltage [V]
RUN time [h]
ON time [h]
0.0 to 999.9
0.0 to 100.0
001C to 0025
0026 to 002F
-
V
%
116C
116D
4.2 Parameter group A

Parameter
No.
Function name
A001
Frequency reference selection
A201
2nd frequency reference selection
A002
A202
RUN command selection

2nd RUN command selection
A003
A203
A004
A204
A005
Base frequency
2nd base frequency
Maximum frequency
2nd maximum frequency
O/OI selection
A011
A012
A013
A014
A015
O start frequency
O end frequency
O start ratio
O end ratio
O start selection
A016
A020
A220
O, OI sampling
Multi-step speed reference 0
2nd multi-step speed reference 0

01: Terminal
02: Digital operator (F001)
03: Modbus communication
10: Frequency operation result
01: Terminal
03: Modbus communication
30 to maximum frequency [A004]
30 to 2nd maximum frequency [A204]
30. to 400.
00: Switches between O/OI via terminal AT
02: Switches between O/FREQ adjuster via terminal AT
03: Switches between FI/FREQ adjuster via terminal AT
04: O input only
05: OI input only
0.0 to Max. frequency
0. to 100.
00: External start frequency (A011 set value)
01: 0 Hz
1. to 17.
0.0/starting frequency to max. frequency
0.0/starting frequency to 2nd max. frequency
Default
setting
00
Changes
during
operation
No
Unit
Modbus
address
(hex)
1019
02
No
101A
50
No
Hz
50
No
Hz
02
No
101B
150C
101C
150D
101D
0.0
No
Hz
0.
100.
01
No
No
8.
6.0
No
Yes
Hz
1020
1022
1023
1024
1025
1026
1029
150F
27
PARAMETER LIST
Parameter
No.
Function name
A021
A022
A023
A024
A025
A026
A027
A028
A029
A030
A031
A032
A033
A034
A035
A038
A039

Jogging frequency
Jogging stop selection
A041
A241
A042
A242
A043
A243
A044
A244
Torque boost selection

2nd torque boost selection
Manual torque boost voltage
2nd manual torque boost voltage
Manual torque boost frequency
2nd manual torque boost frequency
V/F characteristics selection
2nd V/F characteristics selection
A045
A245
A051
Output voltage gain

2nd output voltage gain
DC injection braking selection
A052
A053
A054
A055
A056
DC injection braking frequency

DC injection braking delay time
DC injection braking power
DC injection braking time
DC injection braking method selection
A061
A261
A062
A262
A063
A064
A065
A066
A067
A068
A071
Frequency upper limit

2nd frequency upper limit
Frequency lower limit
2nd frequency lower limit
Jump frequency 1
Jump frequency width 1
Jump frequency 2
Jump frequency 3
PID selection
A072
A073
A074
A075
A076
PID P gain
PID I gain
PID D gain
PID scale
PID feedback selection
A077
Reverse PID function
A078
A081
PID output limit function

AVR selection
A082
AVR voltage selection
A085
RUN mode selection
A086
A092
Energy-saving response/accuracy adjustment

Acceleration time 2
A292
28
Modbus
address
(hex)
102B
102D
102F
1031
1033
1035
1037
1039
103B
103D
103F
1041
1043
1045
1047
1048
1049
0.0/starting frequency to max frequency
0.0
Changes
during
operation
Yes
0.00/starting frequency to 9.99

00: Free-run stop
01: Deceleration stop
02: DC injection braking stop
00: Manual torque boost only
01: Automatic (simple) torque boost
6.00
00
Yes
No
Hz
-
00
No
0.0 to 20.0
5.0
0.0
2.5
0.0
00
Yes
Yes
No
100.
Yes
00
No
104E
1514
1051
0.5
0.0
50
0.5
01
No
No
No
No
No
Hz
s
%
s
1052
1053
1054
1055
1056
0.0
No
Hz
0.0
No
Hz
0.0
0.5
0.0
0.5
0.0
0.5
00
No
Hz
No
105A
1517
105B
1518
105D
105E
1060
1061
1063
1064
1068
1.0
1.0
0.0
1.00
00
Yes
Yes
Yes
No
No
s
s
Time
1069
106A
106B
106C
106D
00
No
106E
0.0
02
No
No
106F
1070
200/400
No
1071
00
No
1072
50
15.00
No
Yes
%
s
1073
1074 (high)
1075 (low)
1519 (high)
151A (low)
0.0 to 50.0
00: Constant torque characteristics (VC)
01: Reduced torque characteristics (VP 1.7th power)
06: Special reduced torque characteristics (Special VP)
20. to 100.
00: Disabled
01: Enabled
02: Frequency control [A052 set value]
0.0 to 60.0
0.0 to 5.0
0. to 100.
0.0 to 60.0
00: Edge operation
01: Level operation
0.0/frequency lower limit to max frequency
0.0/2nd frequency lower limit to 2nd max frequency
0.0/starting frequency to frequency upper limit
0.0/starting frequency to 2nd frequency upper limit
Jump frequency: 0.0 to 400.0
Jump frequency width: 0.0 to 1.0
00: Disabled
01: Enabled
0.2 to 5.0
0.0 to 150.0
0.0 to 100.0
0.01 to 99.99
00: OI
01: O
10: Operation function result
00: OFF (Deviation = Target value - Feedback value)
01: ON (Deviation = Feedback value - Target value)
0.0 to 100.0
00: Always ON
01: Always OFF
02: OFF during deceleration
200-V class: 200/215/220/230/240
400-V class: 380/400/415/440/460/480
00: Normal operation
01: Energy-saving operation
0 to 100
0.01 to 3000.
Default
setting
Unit
Hz
104A
1510
104B
1511
104C
1512
104D
1513
PARAMETER LIST
Parameter
No.
Function name
A093
Deceleration time 2
A293
A094
A294
A095
A295
A096
A296
A097
A098
A101
A102
A103
A104
A105
2-step accel/decel selection

2nd 2-step accel/decel selection
2-step acceleration frequency
2nd 2-step acceleration frequency
2-step deceleration frequency
2nd 2-step deceleration frequency
Acceleration pattern selection
Deceleration pattern setting
OI start frequency
OI end frequency
OI start ratio
OI end ratio
OI start selection
A141
Operation frequency input A setting
A142
Operation frequency input B setting
A143
Operator selection
A145
A146
Frequency addition amount

Frequency addition direction
A151
A152
A153
A154
A155
VR start frequency
VR end frequency
VR start ratio
VR end ratio
VR start selection
00: Switched via multi-function input 09 (2CH)

01: Switched by setting
0.0 to 400.0
00
No
0.0
No
Hz
0.0 to 400.0
0.0
No
Hz
00: Line
01: S-shape curve
0.0 to 400.0
00
No
0.0
No
Hz
0.
100.
01
No
No
Modbus
address
(hex)
1076 (high)
1077 (low)
151B (high)
151C (low)
1078
151D
107A
151F
107C
1521
107D
107E
1080
1082
1083
1084
1085
01
No
108E

0.01 to 3000.
0. to 100.
00: Use OI start frequency [A101]
01: 0 Hz start
02: Input O
03: Input OI
00: Addition (A + B)
01: Subtraction (A - B)
03: Multiplication (A x B)
0.0 to 400.0
00: Adds A145 value to output frequency
01: Subtract A145 value from output frequency
0.0 to 400.0
0. to 100.
00: Use VR start frequency [A151]
01: 0 Hz start
15.00
Changes
during
operation
Yes
Default
setting
Unit
s
02
108F
00
No
1090
0.0
00
Yes
No
Hz
1091
1093
0.0
No
Hz
0.
100.
01
No
No
1095
1097
1098
1099
109A
Default
setting
00
Changes
during
operation
No
1.0
1.0
00
4.3 Parameter group B

Parameter
No.
Function name
b001
Retry selection
b002
b003
b004
Allowable momentary power interruption time

Retry wait time
Momentary power interruption/undervoltage trip
during stop selection
b005
Momentary power interruption retry time

selection
b011
Starting frequency at active frequency matching

restart
b012
b212
b013
b213

Electronic thermal characteristics selection
2nd electronic thermal characteristics selection
b021
b221
Overload limit selection

2nd overload limit selection
b022
b222

2nd overload limit level
b023
b223
b028
b228
b029
Overload limit parameter

2nd overload limit parameter
Overload limit source selection
2nd overload limit source selection
Deceleration rate constant at active frequency
matching restart level
Active frequency matching restart level
b030

00: Alarm
01: 0 Hz start
02: Frequency matching start
03: Trip after frequency matching deceleration stop
0.3 to 25.0
0.3 to 100.0
00: Disabled
01: Enabled
00: 16 times
01: No limit
00: Frequency at interruption
01: Max. frequency
02: Set frequency
01: Constant torque characteristics
00: Disabled
01: Enabled in acceleration/constant speed operation
02: Enabled in constant speed operation
0.1 to 3000.0
00: b022, b222 set values
01: Input terminal O
0.1 to 3000.0
Modbus
address
(hex)
10A5
No
No
No
s
s
10A6
10A7
10A8
00
No
10A9
00
No
1170
Rated
current
No
00
No
10AD
1527
10AE
1528
01
No
10B5
1529
1.5 x
Rated
current
1.0
No
10B6
152A
No
00
No
0.5
No
10B7
152B
10BB
152C
1171
Rated
current
No
1172
Unit
29
PARAMETER LIST
Parameter
No.
Function name
b031
Soft lock selection
b050
Selection of non-stop function at momentary

power interruption
b051
b080
Starting voltage of non-stop function at

Stop deceleration level of non-stop function at
Deceleration time of non-stop function at
Deceleration starting width of non-stop function
at momentary power interruption
Overvoltage protection proportional gain during
deceleration
Overvoltage protection integral time during
deceleration
AM adjustment
b082
b083
b084
Starting frequency
Carrier frequency
Initialization selection
b085
b086
b087
Initialization parameter selection

Frequency conversion coefficient
STOP key selection
b088
Free-run stop selection
b089
Monitor display selection
b091
Stop selection
b092
Cooling fan control
b130
Overvoltage LAD stop function
b131
Overvoltage LAD stop function level setting
b133
Overvoltage protection function selection during

deceleration
b134
Overvoltage protection level setting during

deceleration
b140
Overcurrent suppression function
b150
Automatic carrier reduction
b151
Ready function selection
b052
b053
b054
b055
b056
30

00: Data other than b031 cannot be changed when terminal SFT is ON
01: Data other than b031 and the specified frequency
parameter cannot be changed when terminal SFT is ON
02: Data other than b031 cannot be changed
03: Data other than b031 and the specified frequency
parameter cannot be changed
10: Data other than parameters changeable during operation cannot be changed
00: Disabled
01: Enabled (Stop)
02: Enabled (Restart)
0.0 to 1000.
Modbus
address
(hex)
10BC
No
10C9
No
10CA
01
Changes
during
operation
No
00
0.0
Default
setting
Unit
10CB
0.01 to 3000
1.0
No
10CC
0.0 to 10.0
0.0
No
Hz
10CE
0.2 to 5.0
0.2
Yes
1173
0.0 to 150.0
0.2
Yes
1174
0. to 255.
(Shared with C086 for AM offset adjustment)
0.5 to 9.99
2.0 to 12.0
00: Clears the trip monitor
01: Initializes data
02: Clears the trip monitor and initializes data
00 (Do not change)
0.1 to 99.9
00: Enabled
01: Disabled
00: 0 Hz start
01: Active frequency matching restart
01: Output frequency monitor
02: Output current monitor
03: Rotation direction monitor
04: PID feedback value monitor
05: Multi-function input monitor
06: Multi-function output monitor
07: Frequency conversion monitor
00: Decel-Stop
01: Free-RUN
00: Always ON
01: ON during RUN
02: Depends on the fin temperature
00: Disabled
01: Enabled
200-V class: 330. to 395.
400-V class: 660. to 790.
00: Disabled
01: Enabled
200-V class: 330. to 395.
400-V class: 660. to 790.
00: Disabled
01: Enabled
00: Disabled
01: Enabled
00: Disabled
01: Enabled
100.
Yes
10CF
1.5
3.0
00
No
No
No
Hz
kHz
10D1
10D2
10D3
00
1.0
00
No
Yes
No
10D4
10D5
10D6
00
No
10D7
01
Yes
10D8
00
No
10DA
01
No
10DB
00
No
10F5
380/760
Yes
10F6
00
No
1176
380/760
No
1177
01
No
10F7
00
No
10F8
00
No
10F9
PARAMETER LIST
4.4 Parameter group C

Parameter
No.
Function name
C001
C201
C002
C202
C003
C203
C004
C204
C005
C205
C011
C012
C013
C014
C015
C021

Multi-function output terminal 11 selection
C026
Relay output (AL2, AL1) function selection
C028
AM selection
C031
C036
C038
Multi-function output terminal 11 contact

selection
Relay output (AL2, AL1) contact selection
Light load signal output mode
C039
Light load detection level
C041
C241
C042
C043
C044
C052
C053
C070
Overload warning level

2nd overload warning level
Arrival frequency during acceleration
Arrival frequency during deceleration
PID deviation excessive level
PID FB upper limit
PID FB lower limit
Operator/Modbus selection
C071
Communication speed selection (Baud rate

selection)
C072
Communication station No. selection

00: FW (forward)
01: RV (reverse)
02: CF1 (multi-step speed setting binary 1)
06: JG (jogging)
07: DB (external DC injection braking)
08: SET (2nd control)
09: 2CH (2-step acceleration/deceleration)
11: FRS (free-run stop)
12: EXT (external trip)
13: USP (USP function)
15: SFT (soft lock)
16: AT (analog input switching)
18: RS (reset)
19: PTC (thermistor input)
20: STA (3-wire start)
21: STP (3-wire stop)
22: F/R (3-wire forward/reverse)
23: PID (PID enabled/disabled)
24: PIDC (PID integral reset)
27: UP (UP/DWN function accelerated)
28: DWN (UP/DWN function decelerated)
29: UDC (UP/DWN function data clear)
31: OPE (forced operator)
50: ADD (frequency addition)
51: F-TM (forced terminal block)
52: RDY (ready function)
53: SP-SET (special 2nd function)
64: EMR (emergency shutoff*1)
255: No function
Default
setting
00
Changes
during
operation
No
Unit
Modbus
address
(hex)
1103
00
1532
01
1104
01
1533
18
1105
18
1534
12
1106
12
1535
02
1107
02
1536
*1. The EMR is set forcibly with switch S8, not with parameters.
00: NO
01: NC
00
No
00: RUN (signal during RUN)

01: FA1 (constant speed arrival signal)
02: FA2 (over set frequency arrival signal)
03: OL (overload warning)
04: OD (excessive PID deviation)
05: AL (alarm output)
06: Dc (disconnection detection)
07: FBV (PID FB status output)
08: NDc (network error)
09: LOG (logic operation output)
10: ODc (do not use)
43: LOC (light load detection signal)
00: Output frequency
01: Output current
00: NO contact at AL2, NC contact at AL1
01: NC contact at AL2, NO contact at AL1
00
No
00: Enabled during acceleration/deceleration/constant

speed
01: Enabled only during constant speed
0.0 to 2.0 x Rated current (0.0 setting: function disable)
0.0: Does not operate
0.0 to 400.0
0.0 to 100.0
0.0 to 100.0
02: Digital Operator
03: Modbus
04: 4800 bps
05: 9600 bps
06: 19200 bps
1. to 32.
05
110B
110C
110D
110E
110F
1114
1119
00
No
111B
00
No
111D
01
01
No
1122
1178
Rated
current
Rated
current
No
1179
No
0.0
No
Hz
3.0
100.0
0.0
02
No
No
%
%
No
1124
153A
1126
1128
1129
112E
112F
1137
04
No
1137
1.
No
1139
31
PARAMETER LIST
Parameter
No.
Function name
C074
Communication parity selection
C075
Communication stop bit selection
C076
Communication error selection
C077
C078
C081
C082
C086
C091
C101
Communication error timeout

Communication wait time
O adjustment
OI adjustment
AM offset adjustment
Not used
UP/DWN selection
C102
Reset selection
C141
Logic operation function A input
C142
Logic operation function B input
C143
Logic operator selection
C144
C145
C148
C149
Output terminal 11 ON delay

Output terminal 11 OFF delay
Relay output ON delay
Relay output OFF delay
Modbus
address
(hex)
113B
No
113C
02
No
113D
0.00
0.
100.0
No
No
Yes
s
ms
%
0.0 to 10.0
Use 00 (Do not change)
00: Do not store the frequency data
01: Store the frequency data
00: Trip reset at rising edge of RS input
01: Trip reset at falling edge of RS input
02: Enabled only during trip (Reset at rising edge of RS
input)
00: RUN (signal during RUN)
01: FA1 (constant speed arrival signal)
02: FA2 (over set frequency arrival signal)
03: OL (overload warning)
04: OD (excessive PID deviation)
05: AL (alarm output)
06: Dc (disconnection detected)
07: FBV (PID FB status output)
08: NDc (network error)
10: ODc (do not use)
43: LOC (light load detection signal)
00: AND
01: OR
02: XOR
0.0 to 100.0
0.0
00
00
Yes
No
113E
113F
1141
1142
1145
1149
00
No
114A
00
No
1150
0.0 to 100.0

00: No parity
01: Even
02: Odd
1: 1-bit
2: 2-bit
00: Trip
01: Trip after deceleration stop
02: Ignore
03: Free run
04: Deceleration Stop
0.00 to 99.99
0. to 1000.
0.0 to 200.0
00
Changes
during
operation
No
Default
setting
Unit
01
1151
00
No
1152
0.0
No
0.0
No
1153
1154
1157
1158
Default
setting
Changes
during
operation
Unit
Factory
default
No
kW
No
4.5 Parameter group H

Parameter
No.
Function name
H003
Motor capacity selection
H203
2nd motor capacity selection
200-V class: 0.2/0.4/0.75/1.5/2.2/3.7/5.5/7.5

400-V class: 0.4/0.75/1.5/2.2/3.7/5.5/7.5
H004
Motor pole number selection
2/4/6/8
H204
2nd motor pole number selection
H006
Stabilization parameter
H206
2nd stabilization parameter
Modbus
address
(hex)
1165
1541
Pole
1166
1542
0. to 255.
100
Yes
1168
1544
4.6 Parameter group F

Parameter
No.
Function name
F001
Output frequency setting/monitor
Starting frequency to 1st or 2nd max. frequency
F002
Acceleration time 1
0.01 to 3000.
F202
F003
Deceleration time 1
F203
F004
Operator rotation direction selection
Changes
during
operation
Unit
Yes
Hz
10.0
Yes
1014 (high)
Default
setting
Modbus
address
(hex)
1015 (low)
1501 (high)
1502 (low)
0.01 to 3000.
10.0
Yes
1016 (high)
1017 (low)
1503 (high)
1504 (low)
32
00: Forward
01: Reverse
00
No
1018
OmRON EUROPE B.V. Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
Tel: +31 (0) 23 568 13 00 Fax: +31 (0) 23 568 13 88 industrial.omron.eu
Austria
Tel: +43 (0) 2236 377 800
industrial.omron.at
France
Tel: +33 (0) 1 56 63 70 00
industrial.omron.fr
Netherlands
Tel: +31 (0) 23 568 11 00
industrial.omron.nl
Spain
Tel: +34 902 100 221
industrial.omron.es
Belgium
Tel: +32 (0) 2 466 24 80
industrial.omron.be
Germany
Tel: +49 (0) 2173 6800 0
industrial.omron.de
Norway
Tel: +47 (0) 22 65 75 00
industrial.omron.no
Sweden
Tel: +46 (0) 8 632 35 00
industrial.omron.se
Czech Republic
Tel: +420 234 602 602
industrial.omron.cz
Hungary
Tel: +36 (0) 1 399 30 50
industrial.omron.hu
Poland
Tel: +48 22 458 66 6
industrial.omron.com.pl
Switzerland
Tel: +41 41 748 13 13
industrial.omron.ch
Denmark
Tel: +45 43 44 00 11
industrial.omron.dk
Italy
Tel: +39 02 326 81
industrial.omron.it
Portugal
Tel: +351 21 942 94 00
industrial.omron.pt
Turkey
Tel: +90 212 467 30 00
industrial.omron.com.tr
Finland
Tel: +358 (0) 207 464 200
industrial.omron.fi
South Africa
Tel: +27 (0) 11 579 2600
industrial.omron.eu
Russia
Tel: +7 495 648 94 50
industrial.omron.ru
United Kingdom
Tel: +44 (0) 870 752 08 61
industrial.omron.co.uk
Note: Specifications subject to change without notice.

Cat. No. I128E-EN-01

Omron JX Quick Start Guide

Uploaded by

Copyright:

Available Formats

Omron JX Quick Start Guide

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omron JX Quick Start Guide

Uploaded by

Copyright:

Available Formats

Cat. No.

Compact and complete

QUICK START GUIDE

OMRON Product References

JX Quick Start Guide

Wiring sizes and protection .................................................................................................

4 PARAMETER LIST .............................................................................. 25

JX Quick Start Guide

Parameter group D: Monitors ..........................................

JX Quick Start Guide

JX Quick Start Guide

Basic specifications and optional EMC filter

Max Motor (KW)

Rated output current (A)

1.2 Power ratings

Single-phase 200 V: 3G3JXThree-phase 200 V: 3G3JXApplicable motor capacity

Rated output current (A)

Rated input voltage and frequency

Rated input current (A) single-phase 200 V

JX Quick Start Guide

Three-phase 400 V: 3G3JXApplicable motor capacity

Inverter capacity (KVA)

Rated output current (A)

1.3 Technical specifications

Model number 3G3JXControl methods

Motor overload protection

JX Quick Start Guide

Inverter model 3G3JX-

Earth leakage breaker (ELB)

Fuse size (class J) Rated 600 V

2.2 Installation dimensions

JX Quick Start Guide

Inverter model 3G3JXAB002

Inverter model 3G3JX-

JX Quick Start Guide

2.3 Installation environment

JX Quick Start Guide

2.4 Wiring overview

For Source logic

Power supply input

2.5 Power wiring

Main circuit power supply unit

U/T1, V/T2, W/T3

External DC reactor terminal

Regenerative braking unit connection

Connect optional regenerative braking units (if a braking torque is required)

For grounding (grounding should conform to the local grounding code)

JX Quick Start Guide

Main circuit terminal block

Upper side of the body

Lower side of the body

U/T1 V/T2 W/T3

Upper side of the body

Lower side of the body

2.6 Control wiring

Input power supply

External power supply terminal for input signal (input)

24 VDC internal power supply

Multi-function input selection 1